ELB-1001EWA中文资料

合集下载

Allen-Bradley

安装说明原版说明书译文Hiperface-to-DSL 反馈整流器套件产品目录号 2198-H2DCK变更摘要在后盖板增加了 EAC 徽标。

关于反馈整流器套件本套件适用于 Allen-Bradley® 2090 系列电机反馈电缆，且配备 10 个 Hiperface 编码器信号的接线端子。

Hiperface 编码器信号被转换成兼容的数字伺服链路 (DSL) 反馈信号。

必须为 10 针整流器套件连接器接线，并在正确放置电缆屏蔽层和电缆护套的情况下组装连接器壳体。

准备电缆如要将反馈整流器套件用于现有 Bulletin 2090 电缆，需要进行一些准备工作，以确保电缆屏蔽层、导线长度和剥线长度正确无误。

准备反馈电缆时，请遵循以下说明：•将屏蔽层修剪平整，以免绞线造成相邻端子短路。

•测量导线长度，确保其足够长，以提供工作回路。

•在每根导线上将剥掉足够长的屏蔽层，以提供合适的剥线长度。

反馈电缆尺寸单位为 mm (in.)在电缆护套上的位置2罗克韦尔自动化出版物 2198-IN006D-ZH-P - 2019年10 月Hiperface-to-DSL 反馈整流器套件安装整流器套件按照以下步骤安装整流器套件。

1.拆下保护盖，将信号线连接至合适的端子，为每个连接端留出工作回路。

有关 10 针端子插脚引线，请参见第第3 页页的连接器数据。

2.以 0.25 N•m (2.2 lb•in) 的最大扭矩，拧紧端子螺丝。

3.将屏蔽夹夹到 12 mm (0.5in.) 的裸露电缆屏蔽层上，以在屏蔽编织层和屏蔽夹之间实现高效搭接。

4.连接扎带 (随套件一起提供)，以消除应力。

5.以 0.3 N•m (2.6 lb•in) 的最大扭矩，拧紧屏蔽夹螺丝。

6.更换保护盖，然后安装保护盖螺丝。

以 0.3 N•m (2.6 lb•in) 的最大扭矩，拧紧保护盖螺丝。

7.将 2 针 DSL 连接器插入驱动连接器，然后将安装支架安装到其中一个安装位置 (共 3 个) 上。

78 ZIEHL industrie-elektronik UFR1001E 电压频率监测器商品说明

Voltage Monitoring Type UFRThe grid- and plant protection de-vice UFR1001E monitors voltage and frequency in plants for own generation of electricity. It com-plies with the requirements of VDE-AR-N 4105:2018-11, VDE-AR-N 4110:2018-11, G98, G99, ÖVE/ÖNORM E 8001-4-712:2009 and other standards for generators connected to the public grid.The UFR1001E is a dual-channel device and thus one-fault-proof.Voltage and Frequency Relay UFR1001EGrid- and Plant Protection VDE-AR-N 4105 and 4110, ÖVE-standard, G98 + G99, DIN V VDE 0126-1-1, VFR2013/2014, NRS 0972-1:2017 Ed 2, Synergrid C10/C11UFR1001E••••••••NEW: VDE-AR-N 4105:2018-11, VDE-AR-N 4110:2018-11Part number:S222296The function of the output-relays and of the connected switches can be monitored with feed-back contacts. When a connected switch does not switch off, the UFR does not switch on again. When a switch does not switch on it makes 2 restarts and thus improves availability of monitored plant.The limits are pre-set according to VDE-AR-N 4105-2018-11, VDE-AR-N 4105:2018-11 and other standards. They can be changed if required and be protected with a code and/or a seal.With a 2-step test both channels can be tested indivi-dually and the triggering time of connected switches is measured.The standby input allows a remote shutoff e.g. with a RCR.Under and overvoltage monitoring 15…520 VMeasuring phase-neutral or phase-phaseMonitoring of under- and overfre-quency 45…65 HzMonitoring of quality of voltage (10-minutes-average)Monitoring of vector shift 2…65°Monitoring of rate of change of frequency (ROCOF, df/dt) 0,100...5,000 Hz/sOne-fault-proof with monitoring of connected switches (defeatable), 2 automatic restarts at errorPassive anti-islanding pro-tection acc. to ch. 6.5.3 and app. D2Switching delay adjustable 0.05 … 300 sSwitching back delay adju-stable 0 … 6.000 s Preset values acc. toVDE-AR-N 4105:2018-11 (Pr2), VDE-AR-N 4105-2011-08 (Pr1)VDE-AR-N 4110:2018-11 (PR11-14) and BDEW (Pr 3-6)G98 (G83/2) and G99 (G59/3) for Great Britain ÖVE standard for AustriaVSE/EEA-CH 2014 for SwitzerlandAlarm counter for 100 alarms (trip value, cause and rel. time stamp)Record of added times of alarmsInput for standby with counter and recording of time Test button and simulation with measuring of switching-timesSealing. All values can be read-out when sealed Easy installation and programming with pre-set programsHousing for DIN-rail-mount, 105 mm wide, mounting height 66 mm•••••••••••-----Certificate of conformity Grid and Plant protection acc. to VDE-AR-N 4105 2011-08 and 2018-11 "Plants for generati-on of own energy in low voltage grid"Cerfiticate of conformity Grid and Plant protection acc. to BDEW requirement "Plants for generation of own energy in medium voltage grid"Certificates:CertificateÖVE/ÖNORM E 8001-4-712:2009-12, Anhang ACertificate of compliance DIN V VDE 0126-1-1Certificate de conformitéDIN V VDE 0126-1-1, VFR2013/VFR 2014Certificate of complianceNRS 097-2-1:2010 ed 2.0 South Africa approved Synergrid C10/C11approved Energex RED STD00233accepted by TepcoCertificate of compliance EN 50438:2013Certificate of compliance G59/3:2013, G83/2:2012, G99/1-1+2+3:2018 and G98/1-1+2:2018RD1699:2011 / RD413:2014Technical Data UFR1001EVoltage Monitoring Type UFR2AC/DC 24-270 V, 0/45...65 Hz, <5VA DC: 20,4...297 V, AC: 20,4...297 V 2 change-over contacts see operating manualAC 15...530 V (< 5 V display: 0)AC 15...520 VAC 10...310 V (< 5 V display: 0)AC 15...300 V true RMSadjustable 1,0...180 Vwith neutral: ±0,6% of measured value without neutral: ±0,8% of measured value >100V: -1 digit (resolution 1 V) <100V: -1 digit (resolution 0,1 V)3-phase with / without neutraladjustable 0,05 (± 15ms)...300,0 sadjustable 0 (approx. 200 ms)...6.000 s 40...70 Hz45,00...65,00 Hz 0,05...10,00 Hz ± 0,04 Hz ± 1 digitadjustable 0,05 (± 15ms)...300,0 s adjustable 0 (>200 ms)...6.000 s 0...90,0°2,0...65,0°< 50 msadjustable 3...240 s adjustable 2...20 s0,100...5,000 Hz/s, 4...50 cycles DC 4,5...27 Vmax. 20 mA / output DC 15...35 Vadjustable 0,5...99,0 sEN 602554000 V III 2300 V 100 %-20 °C...+55 °C -25 °C...+70 °C3K5 (except condesation and formation of ice)EN 61 000-6-2EN 61 000-6-3V690 x 105 x 69 mm, mounting height 66 mm IP30IP20DIN-rail 35 mm according to EN 60 715 or screws M4ca. 250 gPower supply Rated supply voltage UsMeasurement phase-phase Setting range phase-phaseMeasuring voltage phase-neutral Setting range phase-neutral Measurement method HysteresisMeasurement accuracy Accuracy of display Measurement functions Switching-delay (dAL)Switching-back-delay (doF)Measurement range Setting range HysteresisMeasurement accuracy Switching delay (dAL)Switching-back-delay (doF)Measurement range Setting rangeSwitching-delay (dAL)Switching-back-delay (doF)Delay at Us on Setting range Voltage I1Current Q1...Q5Voltage Y0...Y1/2Switching time connected swit-chesRated impulse voltage Overvoltage category Pollution degreeRated Insulation voltage Ui Operating timeOperating temperature Storage temperatureClimatic conditions (IEC/EN 60721-3-3)EMC - immunity EMC - emissionDesignDimensions (h x w x d) Protection housing Protection terminals Attachment WeightHousingRelay output Test ConditionsVoltageFrequencyVector-ShiftDigital outputs insulated Input Feed-back-contactsROCOF (df/dt)。

Azbil ACTIVAL 流量计和控制值阀显示面板说明书

© 2015–2016 Azbil Corporation All Rights Reserved.Display Panelfor ACTIVAL ™ Flow Measurement and Control ValveStandalone ModelGeneralDisplay Panel Model QY5010S1000 is the data indicator for ACTIVAL Flow Measurement and Control Valve ModelFVY513X. Display Panel displays data measured by Model FVY513X (flow pressure, flow temperature, flow) and valve position.Besides, the setting buttons on the Display Panel allow you to set and change various data.Features∙Multiple data in a single displayYou can check flow temperature of AHU inlet/outlet, flow pressure of valve inlet/outlet, and flow measured by Model FVY513X and the valve position at one time. ∙Installable 164 ft (50 m) away from Model FVY513XDisplay panel is connected to Model FVY513X with AWG 22 (0.3 mm²), 4-core cable, and max. cable length is 164 ft (50 m).∙ Continuous displayDisplay Panel displays data all the time. You can thus check flow conditions and valve position at any time. ∙Compact and lightweightSmall and light body facilitates installation on an AHU panel or inside a control panel cabinet.∙ Easy wiringSince Display Panel main unit is connected to the base plate with the connector inside, wiring to Display Panel is complete only by connecting the wires to the base plate. ∙Parameter setting and error code check availableDisplay Panel allows you to set parameters and check error codes of Model FVY513X.∙CE Marking certifiedThis product conforms to all the applicable standards of CE Marking.AB-7358-USafety InstructionsPlease read instructions carefully and use the product as specified in this manual. Be sure to keep this manual nearby for quick reference.Usage RestrictionsThis product is targeted for general air conditioning. Do not use this product in a situation where human life might be affected. Also, do not install this product in an atmosphere containing explosive gas or flammable gas.If this product is used in a clean room or a place where particularly high reliability or control accuracy is required, please contact our sales representative. Azbil Corporation will not bear any responsibility for the results produced by the operators.Warnings and CautionsWARNING Alerts users that improper handling may cause death or serious injury.CAUTION Alerts users that improper handling may cause minor injury or material loss.SignsAlerts users possible hazardous conditions caused by erroneous operation or erroneous use. The symbol inside I indicates the specific type of danger.(For example, the sign on the left warns of the risk of electric shock.)Notifies users that specific actions are prohibited to prevent possible danger. The symbol inside Q graphically indicates the prohibited action.(For example, the sign on the left notifies that disassembly is prohibited.)Instructs users to carry out a specific obligatory action to prevent possible danger. The symbol inside d graphically indicates the actual action to be carried out.(For example, the sign on the left indicates general instructions.)WARNINGBefore wiring or maintenance, be sure to turn off the power to the product.Failure to do so might cause electric shock or device failure.CAUTIONInstall and use the product under the operating conditions (for temperature, humidity, power, vibration, shock, mounting direction, atmospheric condition, etc.) as listed in the specifications.Failure to do so might cause fire or device failure.Installation and wiring must be performed by qualified personnel in accordance with all applicable safety standards. All wiring must comply with applicable codes and ordinances.Take anti-lightening measures based on regional and building characteristics.Lightening might cause fire or critical damage to the products without the anti-lightening measures.If more than the rated power voltage is applied to the product, replace the product with new one for your safety.Failure to do so might cause device failure or overheating.Do not disassemble the product.Doing so might cause device failure.Dispose of the product as industrial waste in accordance with your local regulations.Do not reuse all or part of this product.AB-7358-U IMPORTANT:In case an Azbil Corporation product fails, you are required to provide your Equipment with safety design suchas fool-proof design*1, and fail-safe design*2 (anti-flame propagation design, etc.), whereby preventing anyoccurrence of physical injuries, fires, significant damage, and so forth. Furthermore, fault avoidance*3, faulttolerance*4, or the like should be incorporated so that the said Equipment can satisfy the level of reliability andsafety required for your use.*1. A design that is safe even if the user makes an error.*2. A design that is safe even if the device fails.*3. Avoidance of device failure by using highly reliable components, etc.*4. The use of redundancy.Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when theequipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequencyenergy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radiocommunications. Operation of this equipment in a residential area is likely to cause harmful interference in which casethe user will be required to correct the interference at his own expense.Model NumberModel number DescriptionQY5010 Base model number of Display Panel for Model FVY513XS1000S-001 Power supplied from ACTIVAL Flow Measurement and Control Valve standalone model (Model FVY513X)SpecificationsItem Specification Power supply 12 V DC ± 1 V (supplied from Model FVY513X)Power consumption Max. 0.1 VACable AWG 22 (0.3 mm2) , 4-core cableEnvironmental conditions Rated operatingcondition*1Ambient temperature 32 ︒F to 122 ︒F (0 ︒C to 50 ︒C)Ambient humidity 10 % RH to 85 % RH (non-condensing)Vibration 19.4fps2 (5.9 m/s2), 10 Hz to 150 Hz Transport/storageconditionsAmbient temperature -4 ︒F to 158 ︒F (-20 ︒C to 70 ︒C)Ambient humidity 10 % RH to 85 % RH (non-condensing)Vibration 32.2fps2 (9.8 m/s2), 10 Hz to 150 HzEnclosure rating IEC IP40 (dustproof)Display*2Device Liquid Crystal Display (LCD)Items to display Pvin Valve inlet pressure (psig)Pvout Valve outlet pressure (psig)Q Actual flow (GPM)T1 Coil inlet temperature (︒F)T2 Coil outlet temperature (︒F)HC Heat/CoolE ErrorOpening Actual valve position (% in bar graph)Flowrate Actual flow rate (% in bar graph) Communication Transmissionsystem AP-bus (RS-485 communication)Transmission speed 4800 bpsTransmission distance Max. 164 ft (50 m)Number of Display PanelconnectableOne per single Model FVY513XMaterials Case Modified polyphenylene ether (PPE)Base plate Modified polyphenylene ether (PPE)Face plate Polyester (PET)Accessory - Two tapping screws (M4) for mounting- Two 'kPa' unit stickersWeight 0.33 lb (150 g)Notes:*1 LCD service life may shorten if Display Panel is used in an environment with high temperature and humidity. *2 For display accuracy, refer to specification data of Model FVY513X.AB-7358-URecommended Wire SpecificationsCable typeWiring lengthAWG 22 (0.3 mm 2), 4-core(Cable is not supplied with Display Panel.)164 ft (50 m)OptionItem Note Waterproof boxPart No. 83170324-001 Required when Display Panel is installed outdoors.CE Marking ConformityThis product complies with the following Electromagnetic Compatibility (EMC).EMC : EN61326-1 Class A Table 2 (For use in an industrial electromagnetic environment)DimensionsOutside dimensionsFigure 1. Outside dimensionsMounting dimensions of the base plateFigure 2. Mounting dimensions of the base plate1.89" (48 mm) 1.89" (48 mm)1.30" (33 mm)0.59" (15 m m )2.60" (66 m m )Mounting holesCable conduitHook to remove the casefrom the base plate0.59" (15 m m )2.03" (51.5 m m )3.78" (96 mm)3.78" (96 m m )Base plate CaseAB-7358-U Parts IdentificationFigure 3. Parts identification from the base plate Face plateInsertion guide (female)LCD Insertion guide (male)AB-7358-UItems to be displayed on LCDAnalog values such as pressure, flow, and temperature are displayed on the LCD. Setting buttons set/change various parameters and display error description (when an error occurs). Be sure to enable the parameter setting (Parameter 60) before changing any parameters. For details, see AB-7363-U Instruction Manual of ACTIVAL Flow Measurement and Control Valve Standalone Model .Analog values display screenAnalog values display screen appears on the LCD when you turn on the Display Panel.Figure 4. Analog values display screenDisplay areaDescriptionDisplay rangeUnit Item Display Panel connected to: Range 1 Pvin Valve inlet pressure Model FVY5137 0 to 160 psig Model FVY513E 0 to 320 psig 2PvoutValve outlet pressureModel FVY5137 0 to 160 psig Model FVY513E0 to 320psig 3 QActual flow0.000 to 999.9 GPM 4 T 1Coil inlet temperature 14 to 212 °F 5 T 2Coil outlet temperature14 to 212°F Opening Valve position indicated in a bar graph 0 to 100 (with every 10 % increment) % Flowrate Flow indicated in a bar graph 0 to 100 (with every 10 % increment) % E Error occurred ([E] flashes.)− − H C AHU operation mode ([H]: Heat / [C]: Cool)−−Setting buttonsFunction[→] Cursor button Not used in the analog values display screen.[∨] Down button Press this button to switch to the error display screen when the error indicator [E] flashes. [∧] Up buttonPress this button to switch to the error display screen when the error indicator [E] flashes. [ENT] Enter buttonPress and hold this button to switch to the parameter setting screen.Heat/Cool operation modeindicatorDisplay area 1Enter buttonError indicatorDisplay area 2Display area 3 Display area 4Display area 5Up button Down button Cursor button Valve position in bar graphFlow rate in bar graphAB-7358-U● Parameter setting screenPress and hold the [ENT] button to switch to the parameter setting screen from the analog values display screen.Figure 5. Parameter setting screenDisplay area Display item1indicating the parameter setting screen2 Parameter number3 Current setpoint set for the parameter shown in thedisplay area 2.4 No item displayed5 No item displayedSetting buttons Function [→] Cursor button Press this button to select the digit of theparameter number and of the setpoint. The selected digit flashes.[∨] Down button Press this button to change the selected digit.[∧] Up button Press this button to change the selected digit.[ENT] Enter button Press this button to finally set the changedparameter.Press and hold this button to go back to the analog values display screen.Note:No button operation for continuous 10 minutes on the parameter setting screen will automatically switch from the parameter setting screen to the analog values display screen.● Error display screenFigure 6. Error display screenDisplay area Display item [E] Error occurred 1indicating the error display screen2 Error code3 No item displayed4 No item displayed5 No item displayedSetting buttons Function [→] Cursor button Not used in the error display screen. [∨] Down button Press this button to go back to the analogvalues display screen.[∧] Up button Press this button to go back to the analogvalues display screen.[ENT] Enter button Not used in the error display screen. Note:For details of the error codes, refer to AB-7363-U Instruction Manual of ACTIVAL Flow Measurement and Control Valve Standalone Model .Display area 1Display area 2Display area 1Display area 2Display area 3AB-7358-UWiring and InstallationWARNINGBefore wiring or maintenance, be sure to turn off the power to the product.Failure to do so might cause electric shock or device failure.Wiring1) Press the hook on the bottom of the base plate and detach the case.2) Use 0.22" Dia. to 0.24" Dia. (5.5 mm Dia. to 6.0 mm Dia) cable (AWG 22 (0.3 mm2) , 4-core cable recommended) forconnection. Strip 0.20" to 0.24"(5 mm to 6 mm) sheath of each lead wire. (See Fig. 7.)3) Refer to the wiring label (attached to the base plate) and insert stripped lead wires to each terminal.TerminalsarrangementTerminal number Type Lead wire color*1 12 V DC (+) Red (RED)2 0 V Black (BLK)3 AP-bus (+) White (WHT)4 AP-bus (-) Green (GRN)Note: Lead wire color shown in the above table is the wirecolors of the recommended cable.4) Lock each lead wire with lever lock provided on each terminal. Use a tool such as slotted screwdriver to slide the lever lock.Figure 8. Lead wire connection5) Insert the cable into the slit and fix the cable on the base plate with a cable tie.Figure 9. Cable fixed on the base plate0.20" to 0.24"CableAB-7358-UInstallationIMPORTANT:∙ Do not install this product in an atmosphere containing corrosive gas or explosive gas.∙ Do not install this product in a location exposed to direct sunlight. Direct sunlight accelerates LCD degradation.∙ Waterproof box (optional) is required for the product to be installed outdoors. Ask our sales personnel for the waterproof box.Procedure1) Make two holes for two M4 tapping screws (one for upper and the other for lower sides) on a mounting location, such as anAHU side plate or a panel cabinet. Distance between the centers of upper and lower M4 screws is 2.6" ± 0.08" (66 ± 2 mm). 2) Lead the cable (connected to the base plate terminals) out of the base plate through the base plate conduit (on the bottomright), and mount the base plate on the mounting location with the two M4 tapping screws (accessory of Display Panel).Figure 10. Mounting of the base plate with two M4 tapping screws3) Assemble the case with the base plate by inserting the male insertion guide of the case into the female insertion guide of thebase plate. Four insertion guides are provided on the right and left sides (Two on each side). Press the case well so that the case is completely assembled with the base plate. The case is connected to the base plate with the internal connector.Figure 11. Case assembly with the base plateTwo M4 tapping screwsCable conduit(female)Insertion guides (male)CaseAB-7358-U4) Arrange the cable connected to Display Panel.Cautions for arranging the cable: ∙ Do not pull the cable. ∙ To prevent water from flowing down to Display Panel through the cable, let the cable sag, as Fig. 12 shows. ∙ When installing Display Panel on an AHU side plate, seal the wiring hole on the AHU side plate, as Fig. 12 shows. Damp or dew condensation may damage the Display Panel, otherwise.Figure 12. Cable arrangement5) Film is attached to the front surface (face plate) of Display Panel for protection before shipment. Remove the film beforeactivating Display Panel.6) Display Panel is generally installed on a visible position such as on a wall in a machine room or on a control panel cabinet.However, it may possibly be installed outdoors or in a ceiling. In such a case, install the Display Panel as shown in Figs. 13 and 14. Consider the conditions and requirements of your Display Panel installation and decide the location.Figure 13. Display Panel installed outdoors (in a rainproof box)Display PanelSealing materialCableLet the cable sag.Cable led out of the rear side of Display PanelCable led through the conduit of Display Panel 2" (50 mm) stanchionDisplay Panel in a protection boxDisplay Panel in a protection box directly on a wall2" (50 mm) stanchion Display Panel in a plastic box(commercially available)AB-7358-U If Display Panel needs to be installed in a ceiling, install it near the ceiling access panel. Mount Display Panel in a dustproof box to install in a dusty area in a ceiling.Details of AFigure 14. Display Panel installed in a ceilingWiring to Model FVY513XIMPORTANT:Do not pull the cable connected from the terminals of Display Panel to the terminals of Model FVY513X. Display Panel is used in combination with Model FVY513X. To connect the cable to Model FVY513X, refer to Specification/Installation of Model FVY513X.- AB-7350-U: ACTIVAL Flow Measurement and Control Valve Standalone Model Models FVY5137J (PN10/GG-20)- AB-7354-U: ACTIVAL Flow Measurement and Control Valve Standalone Model Models FVY513EJ (JIS 20K/SCPH2)MaintenanceFor replacement of Display Panel, whole unit must be replaced. Display Panel cannot be partially replaced.Care for the face plateClean the face plate with dry soft cloth. Never use detergent or organic solvent to clean the screen. Otherwise, LCD screen will get scratched, discolored, or deformed.AB-7358-URev. 3.0 Jun. 2016 AB-7358-U。

EKB00AA168L00中文资料

For technical questions, contact: aluminumcaps1@Document Number: 25013EKBVishay RoedersteinAluminum CapacitorsRadial StyleFEATURES•Polarized aluminum electrolytic capacitors,non-solid electrolyte•Radial leads, cylindrical aluminum case•Miniaturized, high CV-product per unit volume •Extended temperature range: 105 °C •RoHS compliantAPPLICATIONS•General purpose, industrial and audio-video•Coupling, decoupling, timing, smoothing, filtering,buffering in SMPS•Portable and mobile equipment (small size, low mass)Note10 % capacitance tolerance on request Component outlinesQUICK REFERENCE DATADESCRIPTIONUNIT VALUENominal case size (Ø D x L)mm 5 x 11 to 8 x 11.510 x 12.5 to 18 x 40Rated capacitance range C R µF 2.2 to 22 000Capacitance tolerance %± 20Rated voltage rangeV 6.3 to 100160 to 350400 to 450Category temperature range °C - 55 to + 105- 40 to + 105- 25 to + 105Load lifeh10002000Based on sectional specification IEC 60384-4/EN 130300Climatic category 55/105/5640/105/5625/105/56IEC 60068SELECTION CHART FOR C R , U R AND RELEVANT NOMINAL CASE SIZES (Ø D x L in mm)C R (µF)RATED VOLTAGE (V) (> 100 V see next page)6.31016253550631002.2→→→→→→ 5 x 11 5 x 113.3→→→→→→ 5 x 11 5 x 114.7→→→→→→ 5 x 11 5 x 116.8→→→→→→ 5 x 11 5 x 1110→→→→→→ 5 x 11 5 x 1115→→→→→→ 5 x 11 6.3 x 1122→→→→→→ 5 x 11 6.3 x 1133→→→→→ 5 x 11 6.3 x 118 x 11.547→→→→ 5 x 11→ 6.3 x 1110 x 12.568→→→ 5 x 11 6.3 x 11→8 x 11.510 x 16100→→ 5 x 11→ 6.3 x 11→8 x 11.510 x 20150→ 5 x 11→ 6.3 x 118 x 11.5→10 x 12.512.5 x 20220→ 5 x 11 6.3 x 11→8 x 11.510 x 12.510 x 1612.5 x 25330→ 6.3 x 11→8 x 11.510 x 12.510 x 1610 x 2016 x 25470→ 6.3 x 118 x 11.510 x 12.510 x 1610 x 2012.5 x 2016 x 256808 x 11.5→10 x 12.510 x 1612.5 x 1612.5 x 2012.5 x 2516 x 31.510008 x 11.510 x 12.510 x 1610 x 2012.5 x 2012.5 x 2516 x 2518 x 401500→10 x 1612.5 x 1612.5 x 2016 x 2016 x 2516 x 35.5-2200→10 x 2012.5 x 2012.5 x 2516 x 2516 x 31.516 x 35.5-330012.5 x 1612.5 x 2012.5 x 2516 x 2516 x 35.516 x 35.518 x 40-470012.5 x 2012.5 x 2516 x 2516 x 31.516 x 35.5---680012.5 x 2516 x 2516 x 31.518 x 35.5----10 00016 x 2516 x 35.518 x 35.5-----15 00016 x 35.518 x 35.5------22 00018 x 40-------Document Number: 25013For technical questions, contact: aluminumcaps1@EKBAluminum CapacitorsRadial StyleVishay RoedersteinNote10 % capacitance tolerance on requestSELECTION CHART FOR C R , U R AND RELEVANT NOMINAL CASE SIZES (Ø D x L in mm)C R (µF)RATED VOLTAGE (V)1602002503504004502.2→→ 6.3 x 11→8 x 11.510 x 12.53.3→ 6.3 x 11→8 x 11.510 x 12.510 x 164.7 6.3 x 11→8 x 11.5→10 x 12.510 x 166.88 x 11.5→10 x 12.5→10 x 1610 x 2010→→10 x 12.510 x 1610 x 2012.5 x 2015→→10 x 1610 x 2012.5 x 2012.5 x 2522→10 x 1610 x 2012.5 x 2012.5 x 2516 x 2533→10 x 2012.5 x 2012.5 x 2516 x 2516 x 31.547→12.5 x 2012.5 x 2516 x 2516 x 31.516 x 35.56812.5 x 2516 x 2016 x 2516 x 31.518 x 35.518 x 4010012.5 x 2516 x 2516 x 31.518 x 35.518 x 40-15016 x 2516 x 35.518 x 35.518 x 40--22016 x 31.518 x 35.518 x 40---33018 x 35.518 x 40----47018 x 40----- For technical questions, contact: aluminumcaps1@Document Number: 25013EKBVishay RoedersteinAluminum CapacitorsRadial StyleGENERAL NOTE•For Standard Packaging Quantity (SPQ) and Minimum Order Quantity (MOQ) please refer to our price list or contact customer service •For other packaging forms please refer to Vishay Roederstein General InformationNoteUnless otherwise specified, all electrical values apply at T a = 20 °C , P = 80to 120kPa, RH =45to 75 %.ORDERING EXAMPLEEKB 3300 µF/25 V, ± 20 %, size: 16 x 25 mm Leads: LongOrdering code: MALREKB00JG433E00K Leads: ShortOrdering code: MALREKB05...For 5 ≤ Ø D ≤ 8 mmLeads: Bent open, shortened and formed Ordering code: MALREKB09...For 10 ≤ Ø D ≤ 18 mmLeads: Shortened and formed Ordering code: MALREKB06 ...ELECTRICAL DATASYMBOL DESCRIPTIONU R rated voltageC R rated capacitance at 120 Hz tan δmax. dissipation factor at 120 HzR ESR calculated equivalent series resistance at 120Hz I Rrated ripple current (rms) at 120 Hz and upper category temperatureDocument Number: 25013For technical questions, contact: aluminumcaps1@EKBAluminum CapacitorsRadial StyleVishay RoedersteinELECTRICAL DATA AND ORDERING INFORMATIONU R (V)C R 120Hz (µF)DIMENSIONSD x L (mm)tan δ120 Hz R ESR 120Hz (Ω)I R120 Hz/105 °C(mA)WEIGHT (g)CATALOG NUMBER (Long Leads)6.36808 x 11.50.280.55348 1.10MALREKB00PB368B00K 10008 x 11.50.280.37422 1.10MALREKB00PB410B00K 330012.5 x 160.340.14983 3.00MALREKB00FD433B00K 470012.5 x 200.360.101219 4.00MALREKB00FE447B00K 680012.5 x 250.400.081480 5.00MALREKB00FG468B00K 10 00016 x 250.460.0618078.50MALREKB00JG510B00K 15 00016 x 35.50.560.05223311.0MALREKB00JL515B00K 22 00018 x 400.700.04265214.6MALREKB00KK522B00K 10150 5 x 110.24 2.121340.45MALREKB00AA315C00K 220 5 x 110.24 1.451620.45MALREKB00AA322C00K 330 6.3 x 110.240.962280.46MALREKB00BA333C00K 470 6.3 x 110.240.682720.46MALREKB00BA347C00K 100010 x 12.50.240.32544 2.05MALREKB00DC410C00K 150010 x 160.260.23680 2.20MALREKB00DD415C00K 220010 x 200.280.17844 3.10MALREKB00DE422C00K 330012.5 x 200.300.121148 4.00MALREKB00FE433C00K 470012.5 x 250.320.091421 5.00MALREKB00FG447C00K 680016 x 250.360.0717378.50MALREKB00JG468C00K 10 00016 x 35.50.420.06217211.0MALREKB00JL510C00K 15 00018 x 35.50.520.05248214.0MALREKB00KL515C00K 16100 5 x 110.20 2.651190.45MALREKB00AA310D00K 220 6.3 x 110.20 1.212030.46MALREKB00BA322D00K 4708 x 11.50.200.56349 1.10MALREKB00PB347D00K 68010 x 12.50.200.39488 2.05MALREKB00DC368D00K 100010 x 160.200.27648 2.20MALREKB00DD410D00K 150012.5 x 160.220.19862 3.00MALREKB00FD415D00K 220012.5 x 200.240.141055 4.00MALREKB00FE422D00K 330012.5 x 250.260.101323 5.00MALREKB00FG433D00K 470016 x 250.280.0816578.50MALREKB00JG447D00K 680016 x 31.50.320.06198210.0MALREKB00JS468D00K 10 00018 x 35.50.380.05240914.0MALREKB00KL510D00K 2568 5 x 110.16 3.121080.45MALREKB00AA268E00K 150 6.3 x 110.16 1.411850.46MALREKB00BA315E00K 3308 x 11.50.160.64324 1.10MALREKB00PB333E00K 47010 x 12.50.160.45449 2.05MALREKB00DC347E00K 68010 x 160.160.31591 2.20MALREKB00DD368E00K 100010 x 200.160.21782 3.10MALREKB00DE410E00K 150012.5 x 200.180.161017 4.00MALREKB00FE415E00K 220012.5 x 250.200.121235 5.00MALREKB00FG422E00K 330016 x 250.220.0915628.50MALREKB00JG433E00K 470016 x 31.50.240.07191610.0MALREKB00JS447E00K 680018 x 35.50.280.05233514.0MALREKB00KL468E00KEKBVishay Roederstein Aluminum CapacitorsRadial Style3547 5 x 110.14 3.95960.45MALREKB00AA247F00K 68 6.3 x 110.14 2.731320.46MALREKB00BA268F00K 100 6.3 x 110.14 1.861600.46MALREKB00BA310F00K 1508 x 11.50.14 1.24231 1.10MALREKB00PB315F00K 2208 x 11.50.140.84280 1.10MALREKB00PB322F00K 33010 x 12.50.140.56399 2.05MALREKB00DC333F00K 47010 x 160.140.40521 2.20MALREKB00DD347F00K 68012.5 x 160.140.27740 3.00MALREKB00FD368F00K 100012.5 x 200.140.19974 4.00MALREKB00FE410F00K 150016 x 200.160.141188 6.00MALREKB00JE415F00K 220016 x 250.180.1114268.50MALREKB00JG422F00K 330016 x 35.50.200.08185711.0MALREKB00JL433F00K 470016 x 35.50.220.06222414.0MALREKB00JL447F00K5033 5 x 110.12 4.82920.45MALREKB00AA233H00K 22010 x 12.50.120.72376 2.05MALREKB00DC322H00K 33010 x 160.120.48504 2.20MALREKB00DD333H00K 47010 x 200.120.34657 3.10MALREKB00DE347H00K 68012.5 x 200.120.23927 4.00MALREKB00FE368H00K 100012.5 x 250.120.161226 5.00MALREKB00FG410H00K 150016 x 250.140.1214428.50MALREKB00JG415H00K 220016 x 31.50.160.10144210.0MALREKB00JS422H00K 330016 x 35.50.180.07179411.0MALREKB00JL433H00K632.2 5 x 110.1060.29260.45MALREKB00AA122J00K3.3 5 x 110.1040.19320.45MALREKB00AA133J00K4.7 5 x 110.1028.22380.45MALREKB00AA147J00K 6.8 5 x 110.1019.50460.45MALREKB00AA168J00K 10 5 x 110.1013.26560.45MALREKB00AA210J00K 15 5 x 110.108.84680.45MALREKB00AA215J00K 22 5 x 110.10 6.03830.45MALREKB00AA222J00K 33 6.3 x 110.10 4.021160.46MALREKB00BA233J00K 47 6.3 x 110.10 2.821390.46MALREKB00BA247J00K 688 x 11.50.10 1.95197 1.10MALREKB00PB268J00K 1008 x 11.50.10 1.33239 1.10MALREKB00PB310J00K 15010 x 12.50.100.88340 2.05MALREKB00DC315J00K 22010 x 160.100.60451 2.20MALREKB00DD322J00K 33010 x 200.100.40603 3.10MALREKB00DE333J00K 47012.5 x 200.100.28844 4.00MALREKB00FE347J00K 68012.5 x 250.100.2011075.00MALREKB00FG368J00K 100016 x 250.100.1314908.50MALREKB00JG410J00K 150016 x 35.50.120.11177011.0MALREKB00JL415J00K 220016 x 35.50.140.08177011.0MALREKB00JL422J00K 330018 x 400.160.06268914.6MALREKB00KK433J00KELECTRICAL DATA AND ORDERING INFORMATIONU R (V)C R120Hz(µF)DIMENSIONSD x L(mm)tan δ120 HzR ESR120Hz(Ω)I R120 Hz/105 °C(mA)WEIGHT(g)CATALOGNUMBER(Long Leads)Document Number: 25013For technical questions, contact: aluminumcaps1@EKBAluminum CapacitorsRadial StyleVishay Roederstein1002.2 5 x 110.0848.23260.45MALREKB00AA122L00K3.3 5 x 110.0832.15320.45MALREKB00AA133L00K4.7 5 x 110.0822.58380.45MALREKB00AA147L00K 6.8 5 x 110.0815.60460.45MALREKB00AA168L00K 10 5 x 110.0810.61560.45MALREKB00AA210L00K 156.3 x 110.087.07780.46MALREKB00BA215L00K 22 6.3 x 110.08 4.82950.46MALREKB00BA222L00K 338 x 11.50.08 3.22137 1.10MALREKB00PB233L00K 4710 x 12.50.08 2.26190 2.05MALREKB00DC247L00K 6810 x 160.08 1.56251 2.20MALREKB00DD268L00K 10010 x 200.08 1.06332 3.10MALREKB00DE310L00K 15012.5 x 200.080.71477 4.00MALREKB00FE315L00K 22012.5 x 250.080.48630 5.00MALREKB00FG322L00K 33016 x 250.080.328568.50MALREKB00JG333L00K 47016 x 250.080.2310218.50MALREKB00JG347L00K 68016 x 31.50.080.16134410.0MALREKB00JS368L00K 100018 x 400.080.11192514.6MALREKB00KK410L00K 1604.7 6.3 x 110.1542.33340.46MALREKB00BA147M00K 6.88 x 11.50.1529.2649 1.10MALREKB00PB168M00K 6812.5 x 250.15 2.93273 5.00MALREKB00FG268M00K 10012.5 x 250.15 1.99331 5.00MALREKB00FG310M00K 15016 x 250.15 1.334508.50MALREKB00JG315M00K 22016 x 31.50.150.9059610.0MALREKB00JS322M00K 33018 x 35.50.150.6082214.0MALREKB00KL333M00K 47018 x 400.150.42101514.6MALREKB00KK347M00K 2003.3 6.3 x 110.1560.29290.46MALREKB00BA133S00K 2210 x 160.159.04111 2.20MALREKB00DD222S00K 3310 x 200.15 6.03149 3.10MALREKB00DE233S00K 4712.5 x 200.15 4.23208 4.00MALREKB00FE247S00K 6816 x 200.15 2.93279 6.00MALREKB00JE268S00K 10016 x 250.15 1.993688.50MALREKB00JG310S00K 15016 x 35.50.15 1.3351711.0MALREKB00JL315S00K 22018 x 35.50.150.9067114.0MALREKB00KL322S00K 33018 x 400.150.6085014.6MALREKB00KK333S00K 2502.2 6.3 x 110.1590.43230.46MALREKB00BA122N00K 4.78 x 11.50.1542.3340 1.10MALREKB00PB147N00K 6.810 x 12.50.1529.2656 2.05MALREKB00DC168N00K 1010 x 12.50.1519.8968 2.05MALREKB00DC210N00K 1510 x 160.1513.2692 2.20MALREKB00DD215N00K 2210 x 200.159.04121 3.10MALREKB00DE222N00K 3312.5 x 200.15 6.03175 4.00MALREKB00FE233N00K 4712.5 x 250.15 4.23227 5.00MALREKB00FG247N00K 6816 x 250.15 2.933038.50MALREKB00JG268N00K 10016 x 31.50.15 1.9940210.0MALREKB00JS310N00K 15018 x 35.50.15 1.3355414.0MALREKB00KL315N00K 22018 x 400.150.9069414.6MALREKB00KK322N00KELECTRICAL DATA AND ORDERING INFORMATIONU R (V)C R 120Hz (µF)DIMENSIONSD x L (mm)tan δ120 Hz R ESR 120Hz (Ω)I R120 Hz/105 °C(mA)WEIGHT (g)CATALOG NUMBER (Long Leads) For technical questions, contact: aluminumcaps1@Document Number: 25013EKBVishay RoedersteinAluminum CapacitorsRadial Style3503.38 x 11.50.2080.3834 1.10MALREKB00PB133O00K 1010 x 160.2026.5375 2.20MALREKB00DD210O00K 1510 x 200.2017.68100 3.10MALREKB00DE215O00K 2212.5 x 200.2012.06143 4.00MALREKB00FE222O00K 3312.5 x 250.208.04190 5.00MALREKB00FG233O00K 4716 x 250.20 5.642528.50MALREKB00JG247O00K 6816 x 31.50.20 3.9033210.0MALREKB00JS268O00K 10018 x 35.50.20 2.6540714.0MALREKB00KL310O00K 15018 x 400.20 1.7752314.6MALREKB00KK315O00K 4002.28 x 11.50.20120.628 1.10MALREKB00PB122X00K3.310 x 12.50.2080.3839 2.05MALREKB00DC133X00K4.710 x 12.50.2056.4447 2.05MALREKB00DC147X00K 6.810 x 160.2039.0162 2.20MALREKB00DD168X00K 1010 x 200.2026.5382 3.10MALREKB00DE210X00K 1512.5 x 200.2017.68118 4.00MALREKB00FE215X00K 2212.5 x 250.2012.061555.00MALREKB00FG222X00K 3316 x 250.208.042118.50MALREKB00JG233X00K 4716 x 31.50.20 5.6427610.0MALREKB00JS247X00K 6818 x 35.50.20 3.9037314.0MALREKB00KL268X00K 10018 x 400.20 2.6542714.6MALREKB00KK310X00K 4502.210 x 12.50.20120.627 2.05MALREKB00DC122P00K3.310 x 160.2080.3836 2.20MALREKB00DD133P00K4.710 x 160.2056.4443 2.20MALREKB00DD147P00K 6.810 x 200.2039.0156 3.10MALREKB00DE168P00K 1012.5 x 200.2026.5380 4.00MALREKB00FE210P00K 1512.5 x 250.2017.681075.00MALREKB00FG215P00K 2216 x 250.2012.061448.50MALREKB00JG222P00K 3316 x 31.50.208.0419310.0MALREKB00JS233P00K 4716 x 35.50.20 5.6424211.0MALREKB00JL247P00K 6818 x 400.203.9035214.6MALREKB00KK268P00KELECTRICAL DATA AND ORDERING INFORMATIONU R (V)C R120Hz(µF)DIMENSIONSD x L (mm)tan δ120 Hz R ESR 120Hz (Ω)I R120 Hz/105 °C(mA)WEIGHT (g)CATALOG NUMBER (Long Leads)LOW TEMPERATURE BEHAVIORIMPEDANCE RATIOZ(T2)/Z(T1)RATED VOLTAGE(V)T2/T1 6.31016253550 ~ 100160200 ~ 350400450- 25/+ 20 °C 54322234610- 40/+ 20 °C108643348--ADDITIONAL ELECTRICAL DATAPARAMETERCONDITIONSVALUECurrent Leakage current(T est conditions: U R , 20 °C)After 1 minute at U R I L1 ≤ 0.03 x C R x U R or 4 µA for U R ≤ 100 V (whichever is greater)After 2 minutes at U R I L2 ≤ 0.01 x C R x U R or 3 µA for U R ≤ 100 V (whichever is greater) After 5 minutes at U RI L5 ≤ 0.02 x C R x U R+ 15 µAfor U R > 100 V (whichever is greater)ResistanceEquivalent series resistance (ESR)Calculated from tan δmax.and C RESR = tan δ/2 π f C RDocument Number: 25013For technical questions, contact: aluminumcaps1@EKBAluminum CapacitorsRadial StyleVishay RoedersteinMULTIPLIER OF RIPPLE CURRENT (I R ) AS A FUNCTION OF FREQUENCYFREQUENCY(Hz)I R MULTIPLIER FOR U R ≤ 100 VC R ≤ 47 µFC R = 68 to 680 µFC R ≥ 1000 µF500.750.800.85120 1.00 1.00 1.00300 1.35 1.25 1.101000 1.55 1.35 1.15≥ 10 0002.001.501.15MULTIPLIER OF RIPPLE CURRENT (I R ) AS A FUNCTION OF FREQUENCYFREQUENCY(Hz)I R MULTIPLIER FOR U R 160 V to ≤ 450 VC R = 47 to 220 µFC R ≥ 330 µF500.800.90120 1.00 1.00300 1.25 1.101000 1.40 1.13≥ 10 0001.601.15TEST PROCEDURES AND REQUIREMENTSTESTPROCEDURE (QUICK REFERENCE)REQUIREMENTSLoad lifeT amb = 105 °C U R and I R appliedAfter 1000 hours Ø 5, Ø 6.3, Ø 8 mm After 2000 hours ≥ Ø 10 mmΔ C/C: ± 20 % of initial value I L ≤ spec. limittan δ ≤ 2 x spec. limitShelf lifeT amb = 105 °C No voltage applied After 1000 hoursAfter test: U R to be applied for 30 minutes 24 to 48 hours before measurementΔ C/C: ± 20 % of initial value I L ≤ spec.limittan δ ≤ 2 x spec. limitDisclaimer Legal Disclaimer NoticeVishayAll product specifications and data are subject to change without notice.Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product.Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products.No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay.The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.Product names and markings noted herein may be trademarks of their respective owners.元器件交易网Document Number: 。

亿佰特(Ebyte)-E01nRF24L01芯片-内置PA+LNA-带屏蔽-抗干扰-低辐射-板材特殊-耐高温的无线模块

产品概述
E01 系列是成都公司标志性产品的 2.4G 无线模块，SPI 接口，目前已经稳定量产，并适用于多种应用场景。 E01 系列采用挪威 Nordic 公司原装进口的 nRF24L01P 芯片，所有阻容感器件均采用进口元器件，尤其是晶体，我们使用了高精度宽温晶体，保证其工业特性。发射功率为 20dBm 的模块内置了 PA 功率放大器与 LNA 低噪声放大器，从而提高通信稳定性，延长通信距离；发射功率为 0dBm 的模块均采用进口器件，优秀的设计亦保证了卓越的射频性能，是追求低功耗的客户首选。 E01 系列均严格遵守 FCC、CE、CCC 等国内国外设计规范，满足各项射频相关认证，满足出口要求。
1.1. 通用参数 3 1.2. 电气参数 3 1.2.1. 发射电流 3 1.2.2. 接收电流 3 1.2.3. 关断电流 3 1.2.4. 供电电压 4 1.2.5. 通信电平 4 1.3. 射频参数 4 1.3.1. 发射功率 4 1.3.2. 接收灵敏度 4 1.3.3. 推荐工作频率............................................................................................................................................................................................. 5 1.4. 实测参数 5 1.4.1. 实测距离 5 2. 机械特性.............................................................................................................................

罗克韦尔自动化 1411 型电流互感器数据手册说明书

Technical DataBulletin 1411 Current TransformersCatalog Numbers 1411-2xxx, 1411-8xxx, 1411-125, 1411-126, 1411-180, 1411-600, 1411-601, 1411-604, 1411-606, 1411-608, 1411-615, 1411-616, 1411-617, 1411-ALTopic PageSummary of Changes21411-2xxx Dimensions and Accuracy21411-8xxx Dimensions and Accuracy31411-125 Dimensions and Accuracy51411-126 Dimensions and Accuracy61411-180 Dimensions and Accuracy71411-600 and 1411-601 Dimensions and Accuracy91411-604 Dimensions and Accuracy101411-606 and 1411-608 Dimensions and Accuracy111411-615 Dimensions and Accuracy121411-616 Dimensions and Accuracy131411-617 Dimensions and Accuracy141411-AL Dimensions and Accuracy15Agency Certifications152Rockwell Automation Publication 1411-TD001B-EN-P - June 2017Bulletin 1411 Current TransformersSummary of ChangesThis publication contains new and updated information as indicated in the following table.1411-2xxx Dimensions and AccuracyFigure 1 - 1411-2xxx DimensionsTable 1 - Summary of ChangesTopicPage Updated available catalog numbers.ThroughoutATTENTION: Proper safety precautions must be followed during installation by a trained electrician. Never install while bus is energized. The current transformer must have its secondary terminals that are short circuited or the burden that is connected, before energizing the primary circuit.Table 2 - 1411-2xxx AccuracyCat. No.Current Ratio Models 2SFT, 2SHTModel 2DRL Accuracy at 60 Hz Burden VA at 60 HzAccuracy at 60 Hz Burden VA at 60 Hz 1411-2(1)-500(1)When ordering, prefix Cat No. with model designation required, for example, 1411-2SFT-301 or 1411-2DRL-301.50:5±3% 1.5±2% 1.51411-2(1)-80080:5±2% 2.0±2% 4.01411-2(1)-101100:5±1% 2.0±1% 5.01411-2(1)-151150:5±1% 4.0±1%8.01411-2(1)- 201200:5±1% 4.0±1%10.01411-2(1)-301300:5±1%8.0±1%15.01411-2SFT 1411-2SHT 1411-2DRLRockwell Automation Publication 1411-TD001B-EN-P - June 20173Bulletin 1411 Current Transformers1411-8xxx Dimensions and AccuracyFigure 2 - 1411-8xxxDimensions1411-8SHT1411-8RL4Rockwell Automation Publication 1411-TD001B-EN-P - June 2017Bulletin 1411 Current TransformersTable 3 - 1411-8xxx AccuracyCat. No.Current Ratio VA for ±1% Class ANSI Metering Class at 60 Hz Secondary W inding Resistance (ohms at 75 °C (167°F))Continuous Thermal Rating Factor B0.1B0.2B0.5B0.9B1.8at 30 °C (86 °F)at 55 °C (131 °F)1411-8(1)-201(1)When ordering, prefix catalog number with model designation required, for example, 1411-8SHT-201 or 1411-8RL-301.200:5 5.0 1.2 1.2 2.4 4.8 4.80.030 2.0 2.01411-8(1)-301300:5(2)(2)Approved for revenue metering by Industry Canada No. T-188.15.00.60.6 1.2 2.4 2.40.049 2.0 2.01411-8(1)-401400:5(2)25.00.30.30.6 1.2 2.40.079 2.0 1.51411-8(1)-601600:5(2)50.00.30.30.60.6 1.20.147 1.5 1.331411-8(1)-1021000:5(2)75.00.30.30.30.60.60.246 1.33 1.01411-8(1)-1621600:5(2)100.00.30.30.30.30.60.337 1.330.81411-8(1)-2022000:5(2)120.00.30.30.30.3-0.422 1.00.81411-8(1)-3023000:560.00.30.30.30.3-0.526 1.00.81411-8(1)-4024000:580.00.30.30.30.3-0.9730.80.6Bulletin 1411 Current Transformers1411-125 Dimensions and AccuracyFigure 3 - 1411-125 DimensionsTable 4 - 1411-125 AccuracyCat. No.Current Ratio ANSI Metering Class at 60 HzSecondary Winding Resistance (ohms at 75 °C(167°F))Continuous Thermal Rating FactorB0.1B0.2B0.5B0.9B1.8at 30 °C(86 °F)at 55°C(131 °F)1411-125-1021000:50.30.30.30.6 1.20.187 1.6 1.331411-125-1621600:50.30.30.30.30.60.304 1.6 1.331411-125-2022000:50.30.30.30.30.60.280 1.6 1.01411-125-3023000:50.30.30.30.30.60.421 1.33 1.01411-125-4024000:50.30.30.30.30.30.696 1.00.8Rockwell Automation Publication 1411-TD001B-EN-P - June 201756Rockwell Automation Publication 1411-TD001B-EN-P - June 2017Bulletin 1411 Current Transformers1411-126 Dimensions and AccuracyFigure 4 - 1411-126 DimensionsTable 5 - 1411-126 AccuracyCat. No.Current RatioVA for ±1% ClassANSI Metering Class at 60 HzSecondaryWinding Resistance (ohms at 75 °C (167°F))Continuous Thermal Rating Factor B0.1B0.2B0.5B0.9B1.8at 30 °C (86 °F)at 55 °C (131 °F)1411-126 -401400:5 4.00.6 1.2 2.4 2.4 4.80.116 2.0 2.01411-126-601600:510.00.60.6 1.2 1.2 2.40.173 2.0 2.01411-126-1021000:525.00.30.30.60.6 1.20.289 2.0 1.51411-126-1621600:550.00.30.30.30.30.60.462 1.5 1.01411-126-2022000:560.00.30.30.30.30.30.578 1.33 1.01411-126 -3023000:590.00.30.30.30.30.30.722 1.33 1.01411-126-4024000:5126.00.30.30.30.30.30.962 1.00.81411-126-6026000:5140.00.30.30.30.30.31.2781.00.8Rockwell Automation Publication 1411-TD001B-EN-P - June 20177Bulletin 1411 Current Transformers1411-180 Dimensions and AccuracyFigure 5 - 1411-180 Dimensions1411-180RL1411-180SHT8Rockwell Automation Publication 1411-TD001B-EN-P - June 2017Bulletin 1411 Current TransformersTable 6 - 1411-180 AccuracyCat. No.Current RatioVA for ±1% ClassANSI Metering Class at 60 HzSecondary Winding Resistance (ohms at 75 °C (167°F))Continuous Thermal Rating B0.1B0.2B0.5B0.9B1.8at 30 °C (86 °F)at 55 °C (131 °F)1411-180(1)-500(1)When ordering, prefix catalog number with model designation required, for example, 1411-180RL-301 or 1411-180SHT-301.50:5 1.5 2.4----0.009 1.33 1.01411-180(1)-101100:5 2.5 1.2 2.4 4.8--0.021 1.33 1.01411-180 (1)-151150:5 (2)(2)Approved for revenue metering by Industry Canada. No. T-189.5.00.6 1.2 2.4 4.8-0.038 1.33 1.01411-180(1)-201200:5 (2)12.50.60.6 1.2 2.4-0.051 1.33 1.01411-180(1)-301300:5 (2)25.00.30.30.6 1.2 2.40.076 1.33 1.01411-180(1)-401400:5 (2)50.00.30.30.30.6 1.20.102 1.33 1.01411-180(1)-601600:5 (2)50.00.30.30.30.6 1.20.177 1.33 1.01411-180 (1)-1021000:5 (2)100.00.30.30.30.30.60.253 1.33 1.01411-180(1)-1621600:5 (2)175.00.30.30.30.30.30.359 1.25 1.01411-180(1)-2022000:5 (2)200.00.30.30.30.30.30.4491.00.75Bulletin 1411 Current Transformers1411-600 and 1411-601 Dimensions and AccuracyFigure 6 - 1411-600 and 1411-601 DimensionsTable 7 - 1411-600 AccuracyCat. No.Current Ratio VA at 1% Class ANSI Metering Class at 60 Hz B0.1B0.2B0.51411-600-301300:5 A 2.0 2.4--1411-600-401400:5 A 1.5 2.4 4.8-1411-600-601600:5 A 2.5 2.4 2.4-1411-600-1021000:5 A7.5 1.2 1.2 2.4 1411-600-1621600:5 A20.00.60.6 1.2 1411-600-2022000:5 A30.00.60.60.6 Table 8 - 1411-601 AccuracyCat. No.Current Ratio VA at 1% Class ANSI Metering Class at 60 Hz B0.1B0.2B0.51411-601-301300:5 2.0 2.4--1411-601-401400:5 A 1.0 4.8--1411-601-601600:5 A 2.0 2.4-1411-601-1021000:5 A 5.0 1.2 1.2 4.8 1411-601-1621600:5 A15.0 1.2 1.2 1.2 1411-601-2022000:5 A20.00.60.6 1.2*Modell 1411-600Modell 1411-601Rockwell Automation Publication 1411-TD001B-EN-P - June 20179Bulletin 1411 Current Transformers1411-604 Dimensions and AccuracyFigure 7 - 1411-604 DimensionsCat. No.Current Ratio Burden VA Accuracy1411-604-101100:51±5% 1411-604-151150:51±4% 1411-604-201200:51±2% 1411-604-301300:52±1.5% 1411-604-401400:5 2.5±1.5%10Rockwell Automation Publication 1411-TD001B-EN-P - June 2017Bulletin 1411 Current Transformers1411-606 and 1411-608 Dimensions and AccuracyFigure 8 - 1411-606 and 1411-608 DimensionsTable 10 - 1411-606 AccuracyCat. No.Current Ratio Burden VA Accuracy at 60 Hz1411-606-201200:5 2.52%1411-606-301300:5 3.51%1411-606-401400:551%1411-606-601600:581%1411-606-1021000:5151%1411-606-1221200:5201%Table 11 - 1411-608 AccuracyCat. No.Current Ratio Burden VA Accuracy1411-608-601600:581%1411-608-801800:5121%1411-608-1021000:5131%1411-608-1621600:5271%1411-608-2022000:5331%1411-608-3023000:5501%1411-608-3223200:5541%Rockwell Automation Publication 1411-TD001B-EN-P - June 201711Bulletin 1411 Current Transformers1411-615 Dimensions and AccuracyFigure 9 - 1411-615 DimensionsTable 12 - 1411-615 AccuracyCat. No.Current Ratio Burden VA Accuracy 1411-615-101100:515% 1411-615-201200:523% 1411-615-301300:5 3.51% 1411-615-401400:58.51%12Rockwell Automation Publication 1411-TD001B-EN-P - June 2017Rockwell Automation Publication 1411-TD001B-EN-P - June 201713Bulletin 1411 Current Transformers1411-616 Dimensions and AccuracyFigure 10 - 1411-616 DimensionsTable 13 - 1411-616 AccuracyCat. No.Current RatioBurden Accuracy 1411-616-201200:52VA 3%1411-616-401400:55VA 1%1411-616-801800:55VA1%14Rockwell Automation Publication 1411-TD001B-EN-P - June 2017Bulletin 1411 Current Transformers1411-617 Dimensions and AccuracyFigure 11 - 1411-617 DimensionsTable 14 - 1411-617 AccuracyCat. No.Current Ratio VA at 1% Class ANSI Metering Class B0.1B0.2B0.51411-617-401400:5 A 1.5 2.4 4.8-1411-617-801800:5 A 5.0 1.2 1.2 2.41411-617-1021000:5 A 7.5 1.2 1.2 2.41411-617-1221200:5 A15.00.61.21.2Rockwell Automation Publication 1411-TD001B-EN-P - June 201715Bulletin 1411 Current Transformers1411-AL Dimensions and AccuracyFigure 12 - 1411-AL DimensionsAgency CertificationsTable 15 - 1411-AL AccuracyCat. No.Current Ratio Accuracy at 60 Hz Burden VA at 60 Hz 1411-AL-50050:5±3% 1.51411-AL-80080:5±2% 2.01411-AL-101100:5±1% 2.01411-AL-151150:5±1% 4.01411-AL-201200:5±1% 4.01411-AL-301300:5±1%8.01411-AL-401400:5±1%10.0Cat. No.1411-2xxx1411-8xxx1411-1251411-1261411-1801411-600 and 1411-6011411-6041411-6061411-6081411-6151411-6161411-6171411-ALX X X X X X X X XX X X X X X X X X X X X ANSI/IEEE C57.13X X X X X X X X X X X X X IEC 44-1XXXXXXXXXXXXX16Rockwell Automation Publication 1411-TD001B-EN-P - June 2017Bulletin 1411 Current TransformersAdditional ResourcesThese documents contain additional information concerning related products from Rockwell Automation.Y ou can view or download publications at /global/literature-library/overview.page . T o order paper copies of technical documentation, contact your local Allen-Bradley distributor or Rockwell Automation sales representative.ResourceDescriptionBulletin 1411 Current Transformer Selection Matrix, publication 1411-SG001Provides selection information for the current transformers.Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1Provides general guidelines for installing a Rockwell Automation industrial system.Product Certifications website, /global/certification/overview.pageProvides declarations of conformity, certificates, and other certification details.Bulletin 1411 Current Transformers Notes:Rockwell Automation Publication 1411-TD001B-EN-P - June 201717Allen-Bradley, LISTEN. THINK. SOLVE., Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc.Trademarks not belonging to Rockwell Automation are property of their respective companies.Publication 1411-TD001B-EN-P - June 2017Supersedes Publication 1411-TD001A-EN-P - August 2013Copyright © 2017 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.Rockwell Automation SupportUse the following resources to access support information.Documentation FeedbackY our comments will help us serve your documentation needs better. If you have any suggestions on how to improve this document, complete the How Are W e Doing? form at /idc/groups/literature/documents/du/ra-du002_-en-e.pdf .Technical Support CenterKnowledgebase Articles, How-to Videos, FAQs, Chat, User Forums, and Product Notification /knowledgebase Local Technical Support Phone Numbers Locate the phone number for your country./global/support/get-support-now.pageDirect Dial Codes Find the Direct Dial Code for your product. Use thecode to route your call directly to a technical support engineer./global/support/direct-dial.pageLiterature LibraryInstallation Instructions, Manuals, Brochures, and Technical Data./literatureProduct Compatibility and Download Center (PCDC)Get help determining how products interact, check features and capabilities, and find associated firmware./global/support/pcdc.pageRockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, T el: +90 (216) 5698400Rockwell Automation maintains current product environmental information on its website at /rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page .。

德国Elma超声波清洗系统说明书

made ingermanyQ From manual to fully automatic systems,optimised for fine and ultra-fine cleaning with multi-frequency in 5 tank sizes Q Individually extendible system with option of interface to the clean room (optionally also available with enclosure and laminar flow technology) Q Optional side-ultrasound for complex component geometry Q Various drying systems for different material requirementsUltrasonic Cleaning SystemsTechnical dataUltrasonic Cleaning Re-definedAdvantages and benefitsQ Modular system set-up with 5 tank sizesQ Multi-frequency technology with 25/45 kHz or 37/130 kHzQ For fine and ultra-fine cleaningwith rounded tank corners and special pipeworkQ Optional side-ultrasound technology for special component geometryQ Different drying systems (hot-air, infra-red and vacuum drying) for different material requirementsQ Compact system design with easy-to-clean surfaces Q Integrated ancillaries such as filters, oil separators, etc. Q IPC control with intuitive operating concept Q Equipped with floor tank as standardQ Extremely service and maintenance friendly thanks to the compact system design with easily accessible andswiftly replaceable componentsx tra line 2 is at home in the following industries.The right cleaning system for the task at handDesigned for fine and ultra-fine cleaning tasks, the x tra line 2 can be flexibly deployed and extended due to the modular sys-tem concept (building block system) at any time. Different tank sizes can even be easily accommodated in one system, so that individualised systems are conceptualised.The compact, closed system design enables easy system maintenance. Ancillaries for bath care, such as oil separators, filter units or similar, are positioned inside the system in order to save space. Removable back elements facilitate the easy maintenance and servicing of the x tra line 2. All of the pipework can therefore also be easily accessed.With the new transport robot, the conversion speed is increased by up to 20 %. Furthermore, the following baskets and carriers can be used with the transport robot: Q Normal baskets in transport mode, Q Horizontal turning devices for bulk materials baskets, Q Vertical rotation devices for fixed parts, such as optical lenses, as well asQ Lift rotation devices for positioned components in carriers.Q Production of medical technology and precision optics, Q In the aerospace industry, Q Pharmaceutical industry, Q Manufacture of watches and jewellery, Q Electronics and metalworking industry, and much more.Service, ancillaries and accessories for x tra line 2 systems Individually aligned to your requirementsDifferent parts can be cleaned using the different basket types. Whether it is bulk materials or individually positioned parts, baskets/carriers with different mesh sizes or with coated contact surfaces, the transport of parts is individually tailored to customer requirements and the cleaning process.With bath care, filtration and disposal ancillaries of the x tra line 2, the contamination is easily collected and separated. For example oil, in concentrated form, is collected and can be disposed of in an environmentally-friendly way.Not only is this good for the environment, but it also saves money.Our modular system (building block principle) allows the integration of many of the ancillaries at the rear of the system. Due to the fact that these components can be easily inserted and replaced - through modular, exchange technology - maintenance and servicing periods are reduced to a minimum. Thereby, the system is back in action again very quickly.Another advantage of the x tra line 2 is the small amount of space required by these systems. Due to the integration of individual ancillaries such as oil sepa-rators, filters, etc., the systems require up to 30 % less space and have a neat, structured and easy-to-maintain appearance.So each x tra line 2 cleaning system can be easily integrated into existing production processes.Baskets and carriersThe x tra line 2 offers a comprehensive range of accessories precisely chosen to meet individual customer requirements. Automatic filling/emptying of the tanks, metering systems with automatic filling level control as well as measurement and status monitoring of the media used contribute to ensuring that the optimised cleaning processes remain safe and stable. This provides consistent and reproducible cleaning results for validation purposes.System ancillaries for bath care, filtration and disposalService and maintenance friendly designWith an x tra line 2 cleaning system, the first steps into professional precision cleaning are easy. For smaller quantities, a manual sys-tem, EASY x tra line 2, is the most suitable. If the system capacity is too small, it can be extended at any time thanks to the modular design, or supplemented by various ancillaries.Q In case of low throughputQ Easily extendible process, at any timeQ Throughput-optimised with transport robots and conveyor belts Q Process-safe, as IPC controlledQ Consistently high cleaning qualityQ With enclosureQ in order to meet highest cleaning requirements, Q for noise reduction and Q as interface to clean roomQ Enhanced by semi-automatic handling system for the movement of heavy partsQ User-friendly and ergonomically optimised operationx tra line 2The modular system that adapts to requirementsThus it is quite easy to adapt - even afterwards - to changing conditions and increasing requirements in terms of parts cleaning. Different transport systems such as the pneumatic handling system or the automatic transport system for heavy parts provide high throughput with the required level of process safety.Elma Schmidbauer GmbH · Gottlieb-Daimler-Straße 17 · D-78224 Singen (Germany) · Tel. +49 7731 882-0 · Fax +49 7731 882-266 · The Elma process laboratoryPerfect cleaning results are the measure of all things. In order to achieve these, the focus lies on designing the right sequence of individual process steps.This is where the Elma service concept comes in. Together with our customers, we individually develop a tailor-made cleaning process in the Elma process laboratory. Equipped with state-of-the-art technology, our laboratory carries out cleaning tests for customers on a daily basis and checks these results for the re-quired cleanliness level.Take advantage of our many years of experience and knowledge, and let us design your process solution!S u b j e c t t o t e c h n i c a l a n d o p t i c a l c h a n g e s . · x t r a l i n e 2_E N _11_17Tailor-cut Elma ServiceThe all-round carefree package for your cleaning systemThe Elma Service ConceptFrom process development through to system qualification, commissioning and assembly on site - for our customers we are a reliable and experienced partner for cleaning technology at their side. The worldwide network of Elma sales and service partners ensures that the supply of replacement parts, repair works and maintenance are carried out quickly and efficiently. The re-qualification of your system is also possible at any time. Our customers‘ systems are therefore always swiftly available for operation, contributing to theirsuccess.。

伊玛产品类别

四线
18~36 VDC
PNP NO/NC,NPN NO/NC
4~20 mA,0~10 V
可
PA1108
智慧型
7 LED
内螺纹
G 1/4
400 bar
四线
18~36 VDC
PNP NO/NC,NPN NO/NC
4~20 mA,0~10 V
可
PA1109
智慧型
7 LED
内螺纹
G 1/4
2 bar
四线
18~36 VDC
200
60
M12
接插件
N
Y
N
IP67
否
IA0031
齐平
brass
10~36VDC
1
两线
NO
DC PNP/NPN
200
60
M12
接插件
N
Y
N
IP67
否
IA0032
齐平
brass
10~36VDC
1
两线
NC
DC PNP/NPN
200
60
M12
接插件
N
Y
N
IP67
否
IA0033
非齐平
brass
10~36VDC
可
TA1099
智慧型
7 LED
内螺纹
M18 X 1.5
-40~150°C
四线
20~30 VDC
PNP NO/NC,NPN NO/NC
4~20 mA,0~10 V
可
产品类别
压力变送器(模拟量输出)
压力变送器(开关量输出)
订货号
功能
显示
牙口形式

HMC1001 HMC1002 一维、二维磁阻微电路芯片磁阻传感器说明书

概述HMC1001是一维磁阻微电路，是一个单边封装（SIP）的磁场传感器，感应与管脚方向平行的磁场。

HMC1002是两维磁阻微电路，是封装在小型集成电路封装（SOIC）的双磁场传感器。

两个传感器的敏感方向互相垂直。

传感器A感应与外封装长边方向平行的磁场，传感器B感应与外封装长边方向垂直且与表面平行的磁场。

在外磁场的作用下，磁阻的变化引起输出电压（OUT＋和 OUT-）的变化，并直接表示磁场的强度。

由于器件本身不需聚磁器，所以不会导致迟滞和非重复性。

芯片内置有霍尼韦尔专利的电流带，不需要外部线圈。

传感由四个800-900欧姆的磁阻臂组成惠斯通电桥，在± 2Oe 的范围内具有灵敏度为2.6mV/V/Oe的线性输出，电桥的噪声密度在1Hz以上为25nV/Hz.。

传感器的工作电压为0—10V。

电桥输出的差分放大受桥路的失调电压影响。

当工作电压为8V时，无外磁场作用下的失调电压通常为-10—25mV。

除了磁阻电桥电路之外，传感器内有有一个磁耦合电流带可进行多种模式的操作。

磁场偏置电流带（OFFSET+ 和OFFSET-）上每通过50mA的电流。

相当于在与敏感轴交叉的方向上提供1Oe的磁场。

另一种用法是在偏置电流带上提供反馈信号电流，传感器工作在闭环模式下。

参数电桥电压电桥电阻测量范围磁场分辨率(4)线性度(4)电桥失调灵敏度补偿电流带置位/复位电流带置位/复位电流干扰磁场(4)带宽噪声密度灵敏度温度系数电阻温度系数条件工作电压，-40~85℃桥路电流=10mA线性全量程带宽=0~10Hz,S/R脉冲=4A最佳曲线拟合法设置脉冲后零磁场，电桥电压=8VI offset=50mA ,电桥电压＝８V从OFFSET+至OFFSET-测量从S/R+到S/R-测量0.1%的占空比，2u S电流脉冲灵敏度开始下降，需开始使用S/R脉冲磁信号，下限频率为直流1Hz，电桥电压=5VTCS，电桥电压=8V，-40~85˚CTCR，电桥电压=8V，-40~85˚C最小值600-2.0552.523.03典型值5850270.11-153.22.51.53.2529-30002500最大值121200+2.00.52304.03.51.85单位VΩGaussµ Gauss% 满量程mVmV/V/GaussΩΩAGaussMHznV/Hzppm/˚Cppm/˚C二十脚小型封装的二维磁阻传感器管脚示意图箭头所指方向为传感器产生正输出的磁场方向±1 gauss±2 gaussHMC1001/1002外另加磁场—输出电压特性曲线磁阻传感器在受到强磁场影响（>5Guass ）时输出信号会变坏。

《elma超声波清洗机》课件

ELMA超声波清洗机的安装与调试
01
02
03
安装环境
选择平整、干燥、通风良好的地面或台面，确保电源插座符合安全标准。
安装步骤
按照说明书逐步安装各部件，确保稳固、安全。
调试步骤
检查电源是否正常，调整清洗槽水位至合适位置，开启电源，检查设备运行是否正常。
ELMA超声波清洗机的操作步骤
清洗前准备
通过超声波的高频振动，有效去除各种顽固污渍，提高清洁度。
延长使用寿命
能够彻底清洗精密部件，延长其使用寿命。
节省时间
与传统的手工清洗相比，ELMA超声波清洗机大大提高了清洗效率，节省了大量时间。
安全可靠
在清洗过程中不会对物品造成损伤，安全可靠。
03
CATALOGUE
ELMA超声波清洗机使用方法
这种冲击力能够将物品表面的污垢、油渍等清洗干净，达到高效的清洗效果。
超声波清洗机的应用领域
电子行业
用于清洗电路板、电子元件等，去除松香、焊剂等残留物。
医疗行业
用于清洗手术器械、牙科工具等，确保医疗器械的清洁卫生。
机械行业
用于清洗各种机械零件、金属制品等，去除油污、锈迹等。
光学行业
用于清洗各种光学镜头、眼镜等，去除污垢、油脂等。
总结词：清洗效果不佳可能是由于清洗液选择不当、清洗时间过短或设备功率不足等原因引起的。
根据清洗物品的材质和污渍程度选择合适的清洗液。
检查设备功率是否调整至合适档位，确保足够的清洗力度。
问题三
总结词
遇到故障时，应先了解故障现象，然后根据具体情况进行排查和处理。
了解故障现象
首先需要了解设备出现了什么问题，是否有异常声音、气味或指示灯等。

莱宝真空泵中文说明书

GA/ET-02307/8SOGEV ACSV200, SV300 BR2使用说明书（包括备件清单）适用的编号：10926/10927 : J 97 12 00001 (SV200)10930/10931 : J 97 12 00001 (SV300)95526/95527 – (JAPAN) : J 97 12 00001 (SV200)95536/95537 – (JAPAN) : J 97 12 00001 (SV300)95027 – (USA) : J 97 12 00001 (SV200)95031 – (USA) : J 97 12 00001 (SV300)操作说明书备件清单合格证的EC声明我们，LEYBOLD SA，在此郑重声明，以下规定的产品在设计、型号及流通过程中的改型方面均满足有关EEC指令的安全和健康基本要求。

如果没有我们批准而对产品做任何改变，本声明将无效。

产品结构：单级旋片泵SOGEV AC型号：UV25SV 16 – SV 25 – SV 40 – SV 65SV 100 – SV 200 – SV 300 – SV 585SV 630 – SV 750 – SV 1200和它们的改型，但不带电机交付的泵和带Eex…..电机交付的泵除外。

产品满足下述指令要求：- EEC 机械指令（89/392/EWG）和相继指令91/336/EWG- EEC 低电压指令（73/23/EWG）- EEC 电磁兼容性指令（89/336/EWG）应用协调标准：- EN 1012.1 (project 1993)292.1- EN- EN292.260204.1- EN真空泵安装和启动前，必须阅读并弄懂本使用说明书。

注意：按照最新技术标准和安全规程已经制造出SOGEV AC真空泵。

如果不能正确的安装或不能按指导正确使用，会发生危险。

在一定的运行条件下，当运转真空泵时可能出现危险状态。

如果发生这种情况，请与我们当地办事处联系。

背光L1001说明书

ISW
8
mA
Oscillator frequency振荡频率
Fosc
Hz
4、APPLICATION DIAGRAM＆PAD Description
PAD
NAME
X
Y.
说明
1
IND
－189.5
123.5
调制脉冲输出
2
EL1
－189.5
392
1/8脉冲输出14
TP
204.5
L1001说明书
1、FEATURES功能叙述
L1001为EL背光源驱动电路。工作电压为1.5V或3V。周边元件只需一只电感，
一只二极体和二只三极管。
L1001提供一个高电平的有效的触发端。
*CMOS工艺，高可靠性，高稳定性*内置延时功能（3秒）
*极低的功耗* EL1和EL2的选择可适应不同的这PCB板
266.5
内部测试
5
OSCI
195
141
内部振荡输入
6
OSCO
195
－392
内部振荡输出
7
SEL1
55
－392
选择IND输出类型
8
TG
－189.5
－392
触发输入
9
VDD
－189.5
－247
电源正极
10
SEL2
－189.5
－102
1/8脉冲输出2
`
size:1.02*0.62mm2
* 1.5V和3V电压皆可工作*改变电感参数可驱动大面积EL片。适用于电子表、
电话机、VCD等。
2
*钟表、礼品、电话机、VCD等背光源、妆饰等。
3
PARAMETER

E1001中文资料

T -1 and T -1¾ ,Ultra Bright, Red GaAlAs LEDsLuminous IntensityViewing Forward VoltagePeak Line Part at 20mAAngle at 20mAWave Length No.No.Size Lens Minimum Maximum 2θ½Typical Maximum at 20mADrawing1E169T -1Clear 360mcd 500mcd 50° 1.85V 2.50V 660nm A 2E170T -1Clear 500mcd 700mcd 50° 1.85V 2.50V 660nm A 3E171T -1Clear 700mcd 1000mcd 50° 1.85V 2.50V 660nm A 4E197T -1Clear 1200mcd 1400mcd 50° 1.85V 2.50V 660nm A 5E181T -1¾Clear 500mcd 1000mcd 30° 1.85V 2.5V 660nm B 6E183T -1¾Clear 1300mcd 1600mcd 30° 1.85V 2.5V 660nm B 7E184T -1¾Clear 2000mcd 3500mcd 30°1.85V2.5V 660nm B 8E301T -1¾Diffused 110mcd 200mcd 60° 1.85V 2.5V 660nm B 9E303T -1¾Diffused 200mcd 300mcd 60° 1.85V 2.5V 660nm B 10E304T -1¾Diffused300mcd500mcd60°1.85V2.5V660nmB• RED • RED • RED • RED • RED • RED • RED • RED • RED• RED T -1 and T -1¾, Ultra Bright, Orange InGaAlP LEDsLuminous IntensityViewing Forward VoltagePeak Line Part at 20mAAngle at 20mAWave Length No.No.Size Lens Minimum Maximum 2θ½Typical Maximum at 20mADrawing11E199T -1Orange 500mcd 1600mcd 50° 1.8V 2.3V 620nm C Translucent 12E194T -1¾Orange 700mcd 3000mcd30°1.8V2.3V620nmDTranslucent•ORANGE •ORANGET -1 and T -1¾, Ultra Bright , Yellow InGaAlP LEDsLuminous IntensityViewing Forward VoltagePeak Line Part at 20mAAngle at 20mAWave Length No.No.Size Lens Minimum Maximum 2θ½Typical Maximum at 20mADrawing13E198T -1Y ellow 300mcd 1000mcd 50° 2.0V 2.5V 595nm E Translucent •YELLOW 64Telephone: 781-935-4442sales@ Fax: Engineering Catalog 169T -1 and T -1¾, Super Bright, Green GaP LEDsLuminous IntensityViewing Forward Voltage PeakLine Part at 20mAAngle at 20mA Wave Length No.No.Size Lens Minimum Maximum 2θ½Typical Maximum at 20mA Drawing1E166T -1Clear 100mcd 300mcd 50° 2.2V 2.5V 565nm A 2E196T -1Diffused 40mcd 60mcd 60° 2.2V 2.5V 565nm A 3E168T -1¾Clear100mcd200mcd30°2.2V2.5V565nmB• GREEN • GREEN•GREEN Luminous Intensity ViewingForward VoltageReverse Peak Line Part at 20mA Angle at 20mACurrent Wave Length No.No.Size LensMinimum Typical 2θ½Typical Maximum(V R =5.0V)at 20mADrawing4 E902 T -1 Clear 6800mcd 13,200mcd 15° 3.5V 4.0V 50µA 525nm C5 E903 T -1¾ Clear 13,800mcd 16,000mcd 15° 3.5V 4.0V 50µA 525nm D•GREEN•GREEN65Telephone: 781-935-4442sales@ Fax: Engineering Catalog 169T -1 and T -1¾, Super Bright, Blue GaN LEDsLuminous IntensityViewing Forward VoltagePeak Line Part at 20mAAngle at 20mAWave Length No.No.Size Lens Minimum Maximum 2θ½Typical Maximum at 20mADrawing1E472T -1Clear 20.0mcd90.0mcd20° 4.5V 5.5V 430nm A 2E474T -1¾Clear60.0mcd 150.0mcd16°4.5V5.5V430nmB•BLUE•BLUET -1 and T -1¾, Mega Bright Blue GaN LEDsLuminous Intensity ViewingForward VoltageReverse Peak Line Part at 20mA Angle at 20mACurrent Wave Length No.No.Size LensMinimum Typical 2θ½Typical Maximum(V R =5.0V)at 20mADrawing3 E482 T -1 Clea r 1940mcd 2300mcd 15° 3.6V 4.0V 50µA 470nm C4 E484 T -1¾ Clear 4120mcd 4800mcd 15° 3.6V 4.0V 50µA 470nm D•BLUE •BLUE66Telephone: 781-935-4442sales@ Fax: Engineering Catalog 169T -1¾ Full Color LEDsLuminous IntensityViewing Forward VoltagePeak LinePart at 20mAAngle at 20mAWave Length No.No.Lens Minimum Maximum 2θ½Typical Maximum at 20mADrawing 90mcd 200mcd 15° 2.0V 2.5V 625nm 3E1000Clear50mcd 90mcd 15° 2.2V 2.5V 565nm C12.5mcd 40mcd 15° 4.5V 5.5V 430nm Diffused 20.0mcd 90.0mcd 30° 2.0V 2.5V 625nm 4E1001White20.0mcd 70.0mcd 30° 2.2V 2.5V 565nm C3.2mcd12.5mcd30°4.5V5.5V430nmO WHITEOWHITET -1 and T -1¾, Mega Bright White LEDsLuminous Intensity ViewingForward VoltageReverse Chromaticity Line Part at 20mA Angle at 20mACurrent Coordinates No.No.Size LensMinimum Typical 2θ½Typical Maximum(V R =5.0V)X Typ. Y Typ.Drawing1 E1004 T -1 Clear 3900mcd 4600mcd 25° 3.6V 4.0V 50µA 0.31 0.32 A 2 E1003 T -1¾ Clear 7800mcd 9200mcd 15° 3.6V 4.0V 50µA 0.31 0.32 B•WHITE •WHITE。

亿佰特(Ebyte)-E103-W01是一款超高性价比的100mW(20dBm)串口转Wi-Fi模块-贴片小体积封装

3. 快速入门............................................................................................................................................................................................................6 3.1. 模块作为 Client 与 TCP 服务器连接............................................................................................................................................ 6 3.2. 模块作为 AP 建立 TCP SERVER 与 PC 无线连接...................................................................................................................15 3.3. Smart Config 使用....................................................................................................................................................................... 17 3.4. PWM 的使用.................................................................................................................................................................................. 18 3.5. GPIO 的使用...................................................................................................................................................................................19 3.6. ADC 的使用.................................................................................................................................................................................... 20 3.7. 修改串口波特率............................................................................................................................................................................. 20

Belimo EV100+AKRX-E 能量计量热水系统和冷水系统无线控制阀说明书

EV100+AKRX-EEnergy metering pressure independentcontrol valve that optimizes, documents and proves water coil performance in chilled and hot water systems.• Nominal voltage AC/DC 24 V• Control Modulating, Communicative, Hybrid, Cloud• Measures Energy • Controls Power • Manages Delta TComponentsStructureThe Belimo Energy Valve consists of a characterized control valve, an actuator and a thermal energy meter with a logic and a sensor module.The logic module provides the power supply, the communication interface and the NFC connection of the energy meter. All relevant data are measured and recorded in the sensor module.This modular design of the energy meter means that the logic module can remain in the systemif the sensor module is replaced.External temperature sensor T1Integrated temperature sensor T2Logic module 1Sensor module 2Characterized control valve with actuator 3Technical dataElectrical dataNominal voltageAC/DC 24 V Nominal voltage frequency50/60 HzRemark about nominal voltage range AC 19.2...28.8 V / DC 21.6...28.8 V Power consumption in operation 14 W Transformer sizing 23 VA Connection EthernetRJ45 socketEV100+AKRX-E Electrical data Power over Ethernet PoE DC 37...57 V11 W (PD13W)Conductors, cables AC/DC 24 V, cable length <100 m, no shieldingor twisting requiredShielded cables are recommended for supplyvia PoEData bus communication Communicative control BACnet/IP, BACnet MS/TPModbus TCP, Modbus RTUMP-BusCloudFunctional data Valve size [mm]1" [25]Operating range Y 2...10 VOperating range Y note 4...20 mA w/ ZG-R01 (500 Ω, 1/4 W resistor)Input impedance100 kΩ (0.1 mA), 500 ΩOperating modes optional VDC variablePosition feedback U 2...10 VPosition feedback U variable VDC variableRunning Time (Motor)90 sRunning time fail-safe<35 sNoise level, fail-safe45 dB(A)Control accuracy±5%Min. controllable flow1% of V'nomFluid chilled or hot water, up to 60% glycol max(open loop/steam not allowed)Fluid Temp Range (water)14...250°F [-10...120°C]Close-off pressure ∆ps200 psiDifferential Pressure Range 5...50 psi or 1...50 psi see flow reductions chartin tech docFlow characteristic equal percentage or linearBody Pressure Rating360 psiGPM18.2Pipe connection Internal threadNPT (female)Servicing maintenance-freeManual override external push buttonMeasuring data Measured values FlowTemperatureTemperature sensor Pt1000 - EN 60751, 2-wire technology,inseparably connectedCable length external sensor T1: 3 m Temperature measurement Measuring accuracy absolute temperature± 0.35°C @ 10°C (Pt1000 EN60751 Class B)± 0.6°C @ 60°C (Pt1000 EN60751 Class B)Measuring accuracy temperature difference±0.22 K @ ΔT = 10 K±0.32 K @ ΔT = 20 KResolution0.05°CRemote Temperature Sensor Length Standard: 9.8 ft. [3m]Flow measurement Measuring accuracy flow±2%*Measurement repeatability±0.5% (Flow)Flow measurementSensor technologyUltrasonic with glycol and temperature compensation Safety data Power source ULClass 2 SupplyDegree of protection IEC/ENIP54IP54 when using protective cap or protective grommet for RJ45 socket. Sensor module: IP65Degree of protection NEMA/UL NEMA 1Enclosure UL Enclosure Type 1Agency ListingcULus acc. to UL60730-1A/-2-14, CAN/CSA E60730-1:02CE acc. to 2014/30/EU and 2014/35/EU Quality Standard ISO 9001UL 2043 CompliantSuitable for use in air plenums per Section 300.22(C) of the NEC and Section 602 of the IMCAmbient humidity Max. 95% RH, non-condensing Ambient temperature -22...122°F [-30...50°C]Storage temperature-40...176°F [-40...80°C]MaterialsValve bodyNickel-plated brass body Flow measuring pipe brass body nickel-plated Stem stainless steel Stem seal EPDM (lubricated)SeatPTFE Characterized disc TEFZEL®O-ring EPDM Ballstainless steel••••Safety notesThis device has been designed for use in stationary heating, ventilation and air-conditioning systems and must not be used outside the specified field of application, especially in aircraft or in any other airborne means of transport.Outdoor application: only possible in case that no (sea) water, snow, ice, insolation or aggressive gases interfere directly with the actuator and that is ensured that the ambient conditions remain at any time within the thresholds according to the data sheet.Only authorized specialists may carry out installation. All applicable legal or institutional installation regulations must be complied with during installation.The device contains electrical and electronic components and must not be disposed of as household refuse. All locally valid regulations and requirements must be observed.Application OperationProduct featuresWater-side control of heating and cooling systems for AHUs and water coils.The Energy Valve is an energy metering pressure independent control valve that measures, documents and optimises water coil performance.Operating modeFlow measurement PoE (Power over Ethernet)The HVAC performance device is comprised of four components: characterized control valve(CCV), measuring pipe with flow sensor, temperature sensors and the actuator itself. The adjusted maximum flow (V'max) is assigned to the maximum control signal DDC (typically 10 V /100%). Alternatively, the control signal DDC can be assigned to the valve opening angle or to thepower required on the heat exchanger (see power control). The HVAC performance device can be controlled via communicative or analog signals. The fluid is detected by the sensor in the measuring pipe and is applied as the flow value. The measured value is balanced with the setpoint. The actuator corrects the deviation by changing the valve position. The angle of rotation α varies according to the differential pressure through the control element (see flow curves).*All flow tolerances are at 68°F [20°C] & water.If necessary, the thermal energy meter can be supplied with power via the Ethernet cable. Thisfunction can be enabled via the Belimo Assistant App.DC 24 V (max. 8 W) is available at wires 1 and 2 for power supply of external devices (e.g.actuator or active sensor).Caution: PoE may only be enabled if an external device is connected to wires 1 and 2 or if wires1 and2 are insulated!AccessoriesReplacement sensor modules Description TypeT-piece with thermowell DN 1/2" [15]A-22PE-A09T-piece with thermowell DN 3/4" [20]A-22PE-A10T-piece with thermowell DN 1" [25]A-22PE-A11T-piece with thermowell DN 1 1/4" [32]A-22PE-A12T-piece with thermowell DN 1 1/2" [40]A-22PE-A13T-piece with thermowell DN 2" [50]A-22PE-A14Tools Description TypeConverter Bluetooth / NFCZIP-BT-NFCWire colors:1 = black2 = red3 = white5 = orange6 = pink7 = grey Functions:1 = Com2 = AC/DC 24 V3 = Sensor (optional) 5 = 0...10 V, MP-Bus C1 = D- = A (wire 6) C2 = D+ = B (wire 7)Electrical installationSupply from isolating transformer.Parallel connection of other actuators possible. Observe the performance data.The wiring of the line for BACnet MS/TP / Modbus RTU is to be carried out in accordance withapplicable RS485 regulations.Modbus / BACnet: Supply and communication are not galvanically isolated. Connect earth signalof the devices with one another.Sensor connection: An additional sensor can optionally be connected to the thermal energymeter. This can be a passive resistance sensor Pt1000, Ni1000, NTC10k (10k2), an active sensorwith output DC 0...10 V or a switching contact. Thus the analogue signal of the sensor can beeasily digitised with the thermal energy meter and transferred to the corresponding bussystem.Analog output: An analog output is available on the thermal energy meter. This can be selectedas DC 0...10 V, DC 0.5...10 V or DC 2...10 V. For example, the flow rate or the temperature of thetemperature sensor T1 / T2 can be output as an analog value.EV100+AKRX-EBACnet IP / Modbus TCPAnalog Control BACnet IP / Modbus TCPPoE with BACnet IP / Modbus TCPCable colors:1 = black, GND 2 = red, AC/DC 24 V3 = white, Sensor optional5 = orange, DC 0...10 V, MP-Bus6 = pink, C1 = D- = A7 = grey, C2 = D+ = BBACnet MS/TP / Modbus RTUC₁ = D- = A C₂ = D+ = BConnection with passive sensorConnection with switching contactConnection with active sensorElectrical installationEV100+AKRX-EFunctionsFunctions with specific parameters (parametrisation necessary)MP-Bus, supply via 3-wire connectionMP-Bus via 2-wire connection, local power supplyA) additional MP-Bus nodes(max. 8)A) additional MP-Bus nodes (max. 8)M-Bus with converterM-Bus with converter in parallel mode with BACnet IP / Modbus TCPM-Bus with converter in parallel mode with PoE with BACnet IP /Modbus TCPMP-Bus via 2-wire connection,local power supplyEV100+AKRX-EFunctions with specific parameters (parametrisation necessary)Override control and limiting with DC 24 V with relay contacts (with conventional control or hybrid mode)1) Position control 2) Flow control 3) Power controlFunctionsPermissible installation orientationInstallation location in return Water quality requirementsServicing Flow direction Cleaning of pipes Prevention of stressesInstallation notesThe ball valve can be installed upright to horizontal. The ball valve may not be installed in ahanging position, i.e. with the stem pointing downwards.Installation in the return is recommended.The water quality requirements specified in VDI 2035 must be adhered to.Belimo valves are regulating devices. For the valves to function correctly in the long term, they must be kept free from particle debris (e.g. welding beads during installation work). The installation of a suitable strainer is recommended.Ball valves, rotary actuators and sensors are maintenance-free.Before any service work on the control element is carried out, it is essential to isolate the rotary actuator from the power supply (by unplugging the electrical cable if necessary). Any pumps in the part of the piping system concerned must also be switched off and the appropriate slide valves closed (allow all components to cool down first if necessary and always reduce the system pressure to ambient pressure level).The system must not be returned to service until the ball valve and the rotary actuator have been correctly reassembled in accordance with the instructions and the pipeline has been refilled by professionally trained personnel.The direction of flow, specified by an arrow on the housing, is to be complied with, since otherwise the flow rate will be measured incorrectly.Before installing the thermal energy meter, the circuit must be thoroughly rinsed to remove impurities.The energy meter must not be subjected to excessive stress caused by pipes or fittings.EV100+AKRX-EInlet sectionIn order to achieve the specified measuring accuracy, a flow-calming section or inflow section in the direction of the flow is to be provided upstream from the flow sensor. Its dimensions shouldbe at least 5x DN.Installation notesDimensionsDimensional drawingsTypeWeight EV100+AKRX-E 8.2 lb [3.7 kg]ABC D E F 17.4" [443]11.1” [282] 6.4" [163] 5.5" [140]1.8" [46]1.8" [46]。

伊莱科导轨电表的参数

伊莱科导轨电表的参数伊莱科导轨电表是一种先进的电能表计量设备，它具有诸多优势，能够准确测量电能消耗，并提供可靠的数据支持。

本文将以人类的视角来介绍伊莱科导轨电表的参数，并生动地描述其功能和特点。

我们来了解一下伊莱科导轨电表的外观和尺寸。

该电表由高强度的金属材料制成，具有紧凑的外形设计，适用于各种户内和户外环境。

它的体积小巧，重量轻，便于安装和携带。

不仅如此，伊莱科导轨电表还采用了先进的防护技术，具有防尘、防水、防腐蚀等功能，能够在恶劣的环境条件下正常工作。

我们来看一下伊莱科导轨电表的电参数。

该电表具有广泛的电压和电流测量范围，能够满足不同用电需求。

它采用了高精度的电流互感器和电压互感器，能够实时监测电源的电压和电流变化，并将数据准确传输到中央处理单元。

同时，伊莱科导轨电表还具备多个电能脉冲输出接口，可方便地与其他设备进行数据传输和通信。

除了电参数，伊莱科导轨电表还具备丰富的功能和特点。

首先，它支持多种数据采集方式，可以通过有线或无线方式将数据传输至数据采集终端，方便用户实时监测和管理电能消耗。

其次，伊莱科导轨电表还具备完善的电能计费功能，能够根据设定的电价和用电时间进行精确计费，为用户提供准确的电费结算数据。

此外，该电表还具备数据存储和查询功能，可记录历史用电数据，并支持用户自定义查询和报表生成。

我们来谈一下伊莱科导轨电表的可靠性和安全性。

该电表采用了先进的电路设计和制造工艺，具有稳定性高、抗干扰能力强的特点，能够在各种复杂的电网环境下正常工作。

同时，伊莱科导轨电表还具备多重安全保护功能，如过载保护、短路保护和反接保护等，能够有效防止电表损坏和电网事故的发生。

总的来说，伊莱科导轨电表是一种功能强大、性能稳定的电能计量设备，具有精准测量、可靠性强、安全性高等优势。

它的出现为电能计量领域带来了创新和进步，为用户提供了可靠的电能消耗数据，促进了能源的合理利用。

相信随着科技的不断发展，伊莱科导轨电表将会进一步完善和优化，为人们的生活带来更多便利和舒适。

郑州百年导波雷达说明书

郑州百年阀门有限公司导波雷达说明书目录测量原理 -------------------------------------------------1 产品简介 -------------------------------------------------3 安装指南 -------------------------------------------------4 调试 -------------------------------------------------7 仪表尺寸 --------------------------------------------------8 技术参数 -------------------------------------------------8 产品选型 --------------------------------------------------9导波雷达物位计测量原理导波雷达是基于时间行程原理的测量仪表，雷达波以光速运行，运行时间可以通过电子部件被转换成物位信号。

探头发出高频脉冲并沿缆式或杆式探头传播，当脉冲遇到物料表面时反射回来被仪表内的接收器接收，并将距离信号转化为物位信号。

输入反射的脉冲信号沿缆式或杆式探头传导至仪表电子线路部分，微处理器对此信号进行处理，识别出微波脉冲在物料表面所产生的回波。

正确的回波信号识别由脉冲软件完成，距离物料表面的距离D与脉冲的时间行程T成正比：D=C×T/2其中C为光速因空罐的距离E已知，则物位L为：L=E-D输出通过输入空罐高度E（=零点），满罐高度F（=满量程）及一些应用参数来设定，应用参数将自动使仪表适应测量环境。

对应于4－20mA输出。

测量范围说明：H----测量范围L----空罐距离B----顶部盲区E----探头到罐壁的最小距离顶部盲区是指物料最高料面与测量参考点之间的最小距离。

(彼爱琪)低压互感器样本

6
BH-0.66 ᇹ೰ư࢟ഗઑঢ໭ BH-0.66 SERIES Ⅱ CURRENT TRANSFORMERS
技术参数
Technical Parameters
规格型号母排规格/根数
准确级
130II
180II
200II
220×50II
130×10/1～2
180×10/1～2
100I 62 100×10/1 80×10/1-2 0.2 0.5
5 10 10 20 20 20 20 30 30
订货须知
Placing an Order
1. 请注明互感器型号、额定电流比、准确级、额定容量及安装方式等； 2. 如有特殊要求，可与我公司联系，以便按需订制。 3. 订货时未注明则按黑色所注参数制作，蓝色为特殊制作参数。
BH-0.66 ᇹ೰Ư࢟ഗઑঢ໭ BH-0.66 SERIES I CURRENT TRANSFORMERS
特点
Feature
方圆孔型，主要适用于单根、多根电缆穿越或单根母排穿
越，作为电流测量和电能计量使用。
该产品系列全、规格多、适用面广；30×30I 为加大容量型，100A 及以下额定容量可达到 5～10VA（穿芯匝数仅 2～3 匝）。
5 10 2.5
5
2.5
5
10 15 5
5
5
10 15 5
5
5
10 15 5
5
5
5
10 15 5
5
5
10
10
10
10
10
10
10
10
10
5
10 5
10 5
10
15
15

1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。

EVERLIGHT ELECTRONICS CO.,LTD.
Device Number :DDB-100-029REV: 1.1 10 Bar Graph Displays
MODEL NO :ELB-1001EWA ECN :Page:1/5█ Features :█ Applications:
●Industrial standard size. ●Audio equipment
●Low power consumption. ●Instrument panels
●Categorized for luminous intensity.●Digital read out display
█ Descriptions :
●The ELB-1001 series are ten-element
bar graph displays. D esign for
viewing distances up to 7 meters.
●There are separate anodes and
cathodes for each light segment and
choice of five colors is offered.
●These device is made with white
segments and gray surface.
PART NO CHIP C.C. or C.A.
Material Emitted Color
ELB-1001EWA GaAsP/GaP Orange****
OFFICE : NO. 25,Lane 76,Sec.3, Chung Yang Rd., Tucheng 236, Taipei, Taiwan, R.O.C.
TEL : 886-2-2267-2000,2267-9936
FAX : 886-2-2267-6244,22676189,22676306
EVERLIGHT ELECTRONICS CO.,LTD.
Device Number :DDB-100-029REV: 1.1 10 Bar Graph Displays
MODEL NO :ELB-1001EWA ECN :Page:2/5
█ NOTES:
1.All dimensions are in millimeters tolerance is 0.25mm unless otherwise noted.
2.Above specification may be changed without notice.
Supplier will reserve authority on material change for above specification.
EVERLIGHT ELECTRONICS CO.,LTD.
Device Number :DDB-100-029REV: 1.1
10 Bar Graph Displays
MODEL NO :ELB-1001EWA ECN :Page:3/5
█Absolute maximum ratings at Ta = 25℃：
Parameter Symbol Rating Unit
Reverse Voltage Vr5V
Forward Current If30mA
Operating Temperature Topr-40 to +85℃
Sto r age Temperature Ts t g-40 to +100℃
Soldering Temperature Tsol260 ± 5℃
Power Dissipation Pd100mW
Peak Forward Current(Duty
If(Peak)160mA
1/10 @ 1KHZ)
█Electronic optical characteristics :
Parameter Symbol MIN.TYP.MAX.Unit Condition Luminous Intensity Iv 1.4 2.8----mcd If=10mA
Peak Wavelengthλp----635----nm If=20mA
Dominant Wavelengthλd----625----nm If=20mA
Spectrum Rediation
----45----nm If=20mA Bandwidth△λ
Forward Voltage Vf 1.7 2.0 2.4V If=20mA
Reverse Current Ir--------10µA Vr=5V
EVERLIGHT ELECTRONICS CO.,LTD.
Device Number :DDB-100-029REV: 1.1 10 Bar Graph Displays
MODEL NO :ELB-1001EWA ECN :Page:4/5█ Reliability test item and condition:
NO Item Test Conditions
Test
Hours/Cycle
Sample Size Ac/Re
1Solder Heat TEMP : 260℃ ± 5 ℃ 5 SEC76 PCS0/1
H : +85℃ 30min
2Temperature Cycle∫ 5 min50 CYCLE76 PCS0/1
L : -55℃ 30min
H : +100℃ 5min
3Thermal Shock∫ 10 sec50 CYCLE76 PCS0/1
L : -10℃ 5min
4High Temperature Storage TEMP : 100℃1000 HRS76 PCS0/1 5Low Temperature Storage TEMP : -55℃1000 HRS76 PCS0/1 6DC Operating Life If = 10 mA1000 HRS76 PCS0/1
7High Temperature / High
Humidity
85℃/85% RH1000 HRS76 PCS0/1
EVERLIGHT ELECTRONICS CO.,LTD.
Device Number :DDB-100-029REV: 1.1 10 Bar Graph Displays
MODEL NO:ELB-1001EWA ECN :Page:5/5。