模具常用术语中英文对照

模芯Parting Core 耐落胶Teflon Paste 局部视图Partial View 偏移量Offset
冷料Cold Slag 水塞Water Line Plug 线切割Wire E.D.M 撬模脚Ppy Slot
轮廓Contour 重新加工Reworked 螺纹孔Tapping Hole 配件Components 连接件Fittings 补偿Compensation 斜针Angle Pin 平面度Parallel
接合Engage 倒角Chamfer
替换镶件Interchangeable Mold Inserts 模胚Mold Base
指定吨位的注塑机Specific Press 热嘴Hotnozzle
水嘴接头Water Fitting 火花机Edm
螺纹Eyebolt Thread 熔接线Weildline
回针Stop Pin 压机Press
二级顶出针Sub-Leaderd Pin 嗮纹Texturing
镶件Mold Insert 梯形Trapezoid
加硬Harden 凸缘、法兰Flange
唧嘴Sprue 方铁Spacer Block
设计筒图Design Preliminary 顶针板Ejector Plate
名称块表Title Block 顶针底板Ejector Retainer Plate
版本标识Revision Level 垫板Retainer Plate
材料清单Stock List 后模镶针Core Pin
制模Build Mold 垃圾钉Stop Pin
手动滑块Hand Slide 有托顶针Shoulder Ejector Pin
漏水测试Leak Test 顶针板导套Guided Ejection Bushing
流道排气Runner Vents 针板导柱Guided Ejection Leader Pin
抛光Draw Polish 唧嘴Sprue Bushing
侧抽芯Slide Action 三板模延伸式唧嘴Extension Noozzle Bulishing 加强筋Reinforcing 水口板导套Runner Stripper Pin
三角撑Gusset 定位圈（法兰）Locating Ring
柱子Bossed 管钉（定位销）Dowel Pin
出模斜度Draft 管状管钉Tubular Dowel
外廊Contour 吊环Safety Hoist Ring
落单会议Kick-off 日期印Dating Insert
装卸孔Handing Hole 环保印Recycling Insert
运输安全带Moldstrap 气顶Air Poppet Valve
码模槽Clamp Slot 截水口镶件Runner Shut-Off Insert 撑头Support Pillar 早回Early Ejector Return
螺牙1/2-13 Eye 1/2-13Tap 加速项Accelerated Ejector
导柱位Leader Pin Location 客户Client
产品名Part Name 产品编号Part No
缩水Shrinkage 版本Rev
下模镶件Core Block 上模镶件Cavity Block
小镶件Sub-Insert 下模小镶件Core Sub-Insert
上模小镶件Core Sub-Insert 行位Slide
行位镶件Slide Insert 压条Gib
压紧块（铲机）Jaw 扁顶Blade
硬片（摩擦片）Wear Plate 出模斜波Draft
水口铁Runner Bar 手动滑块模具Hand Slide-In Type Mold 上模水口铁Upper Runner Bar 回针板Backup
下模水口铁Lower Runner Bar 合模Shutoff
弹簧Spring 空隙槽Clearance Slot
水口钩针Sprue Puller Pin 导柱及导套Leader Pin Bushing
顶针Ejector Pin 水口拉钩Spuer Puller
撑头Support Pillar 模框镶件Pocket Insert
直身锁Side Lock 成型热固性塑料模具Thermoset Mold 斜度锁Inter Lock 三板模3-Plat Mold
锁模板Safty Bar 分型面Parting Line
‘O’令（密封圈）O’Ring 司筒Ejector Sleeve
喉塞Plug 垫圈Washer
隔水片Baffrle 烙接线（夹水纹）Weldlin
波子螺丝（行为定位螺丝）吸针Sucker Pin
斜顶Lifter 回针板Retainer Plate
控制开关Switch 顶出板Knock-Out Plate
回针Return Pin 电动安全开关Electrical-Safety Switch 斜导柱Angle Pin 脱开Cut Of Position
推板Stripper Plate 预先决定Preload
A’板A’Plate 缓冲器Bumper
B’板B’Plate 衬垫Cushion
方铁（垫铁）Spacer Block 公差Tolerance
顶针板Ejector Plate 突然性动作Slam
顶针底板Ejector Retainer Plate 销针Dowel
垫板Retainer Plate 钩槽Gib
精磨Finished 有托顶针Shoulder Ejector Pin
通框Through Window 顶针板导套Guided Ejector Bushing
粘后模Stricking Core 针板导柱Guided Ejector Leader Pin 粘水口Sticking Sprue 不干胶Adhesive Sticker
夹水纹Weld Line 线切割Wire-Cut
变形Warpage 电火花Edm
走水不平均Filling 抛光Polishing
走不齐Short Shot 蚀纹Texture
挂成品Part Hanging 探热针Thermocouple
漏水Water Leakage 三打螺丝毫（限螺丝）Stripper Bolt 刮花（擦伤）Galling 盖板Cover Plate
漏电Ele Leakage 齿轮Gear
困气Air Trapping 油唧Hydraulic Cylinder
温度Temperature 司筒Ejector Sleeve
注塑模Injection Mold 导柱Leader Pin
入水Gate 冷料Cold Slag
试板Sampling 压力Pressure
倒圆Fillet 螺纹孔Tapping Hole
顶棍Ejector 连接件Fitting
顶白Stress Mark 粘前模Sticking Cav
名称块表Title Block 替换镶件Interchangeable Mold Insert
版本标识Revision Level 制定吨位的注塑机Specific Press
材料清单Stock List 水嘴接头Water Fitting
斜导柱（斜边）Angle Pin 螺纹Eyebolt Thread
分模面Parting Surface 倒扣Under-Cut
披峰Flash 锁定位Lock
缩水Sink Mark 楔子（铲机）Wedge
氮化Nitride 高产量模量High Volume Running Mold 不规则四边形Trapezoid 剖面图Cross Section
缩水Shrinkage 模具结构Mold Construction
连续的Consecutive 出模角Draft
热流道Manifold 擦位Shut-Off(S/O)
型腔数Cav No 导套Bushing
模号Mold No 导向针Guide Pin
回针Return Pin 胶料Material
加硬Harden 尺寸Dimension
唧嘴Sprue 重要尺寸Critical Dimension 设计筒图Design Preliminary 雕刻Engrave
丝印Silkprint 托司EJ.Guide Pin。