WN 100 - Center bore
管道常用缩写词分析
本规定用于设计图纸及表格中，使达到缩写词的用法统一，同时解决图面空位不够及简化表示方法的作用。
对于技术文件的文字部分如不易了解缩写词的含意时应避免采用缩写词，如必须采用时，除标有*号者外，应加注释。
本规定仅列入管道专业常用的缩写词，未包括流体缩写及常用计量单位符号。
1缩写词ABBREVIATIONSAA Anchor 固定ABS *Absolute 绝对的AISI *American Iron andSteel Institute 美国钢铁学会ANSI *American NationalStandards Institute 美国国家标准学会API *American Petroleum Institute 美国石油学会APPROX *Approximate 大约，近似的ASB Asbestos 石棉ASME *American Society OfTesting Material 美国机械工程师协会ASSY *Assembly 装配，组装ASTM *American Society OfTesting Material 美国材料实验协会ATM *Atmosphere 大气压AWG *American Wire Gage 美国线规AWS *American Welding Society 美国焊接协会AWWA *American Water WorksAssociation 美国水工协会BBB Bolted Bonnet 栓柱连接的阀盖BB By Buyer 买方供货B-B Beveled End-Beveled End 两端为坡口端BC Bolt Circle 螺栓中心圆B.C Bolted Cover(cap) 螺栓连接的阀兰盖（帽）BE Beveled End (for welding) 坡口（焊接用）B.E Bell End 承口BEP Both Ends Plain 两端平BET Both Ends Threaded 两端带螺纹BL Battery Limit 装置区边界BF Blind Flange 法兰盖BLD Blind 盲板BLDG *Building 建筑物BM Bill Of Material 材料表BOP Bottom Of Pipe 管底B-P Beveled End —Plain End 坡口端.平端BV Butterfly valve 蝶阀BWG * Birmingham Wire Gage 伯明翰线规BW Butt Weld 对焊cC Cap 管帽C-C Center to Center 中至中C-E Center to End 中至端面C-F Center to Face 中至面CH-OP Chain Operated 链条操纵的CH.PL Checkered Plate 花纹钢管C.I *Cast Iron 铸铁CL *Class 英制压力等级，等级，种类CLEAR Clearance 间隙COD Continued on Drawing 接续图COL *Column 柱，塔CONC Concentric 同心的CONN Connection 连接，接口CONT *Continue 连续CONT.V. Control Valve 控制阀CPLG Coupling 管接头，连轴节C.R. Concentric Reducer 同心异径管C.S. *Carbon Steel 碳钢C.S. Cold Spring 冷紧C.S.C. Car Seal Close 在关闭状态下封住C.S.O. Car Seal Open 在开启状态下封住CUST Customer 客C.V Check Valve 止回阀DDEG *Degree 度DF Drain funnel 排液漏斗DIA *Diameter 直径DIM *Dimension 尺寸DISCH *Discharge 出口，排出Diaphragm VELVE 隔膜阀DMF Double Male And Female 双重凹凸DN *Double Male And Female 公称直径DN Down 下DR Drain 排液DS Directional Stop 定向限为架DWG *Drawing 图EE *East 东EC External Coating 外面涂防腐层ECC Eccentric 偏心EFW Electric Fusion Welded 电容焊的EL(ELEV) *Elevation 标高；立面ELL Elbow 弯头EQIOP Equipment 设备，装置EQUIV Equivalent 相当的E.R. Eccentric Reducer 偏心异经管ERW Electric Resistance Welded 电阻焊的EW Eye Washer & Shower 洗眼器及淋浴器EXP.JT Expansion Joint 膨胀节FFDN Foundation 基础FF Flat Faced Or Full Faced 全平面；满平面F-F Face To Face 面至面FGW Fusion Gas Welding 气熔焊FIG *Figure 图FL Floor 楼面FLEX TUBE Flexible Tube 挠性管FLG Flange 法兰FLGD Flanged 法兰式的FLGF Flanged Face 法兰面FOB Flat On Bottom 底面平FOT Flat On Top 顶面平FP Fix Point 固定点FS Forged Steel 锻钢FTF Fitting To Fitting 管件直连FTG Fitting 管件FURND Furnished 提供的，装设的FW Field Weld 现伤焊GG Guide 导向GA *Gage 表，表压，规（线规）GALV *Galvanize 镀锌GL Ground Level 地面GLV Globe Valve 截止阀GEAR OP Gear Operated 齿轮传动的GMAW Gas Metal Arc Welding 金属极惰气体保护焊GSKT Gasket 垫片GTAW (Inert)Gas Tungsten Arc Welding 惰性气体保护钨极电弧焊GV Gate Valve 闸阀HH Hanger 吊架HC Hose Connection 软管接头H.CPLG Half Coupling 半节管接头HDR Header 总管HEX *Hexagon 六角形HF Hard Alloy Face on阀内件（阀心）为Valve Trim 硬质合金密封面HH Hand Pole 手孔HOR Horizontal 水平的H.P *High Pressure 高压HS Hose Station 软管IID *Inside Diameter 内径IN *Inch 英寸INS Insulation 隔热INST Instrument 仪表INV Invert (inside bottom of pipe) 管子内底IPS Iron Pipe size 铁管尺寸ISO Isometric Drawing 周测图（空视图）I.S.B.L Inside Battery Limit 装置边界内恻ISNS Inside screw & Non-rising Stem 内螺纹非升杆ISRS Inside screw & Rising stem 内螺纹升杆JJT Joint 接头JS Jack Screw 顶开（起）螺栓LLC Locked Closed 在关闭状态下锁定LEP Large end plain 大端为平的LET Large end Threaded 大端带螺纹LG Long 长LGF Lens Gasket Face 透镜垫连接面L.H.THD Left Hand Thread 左螺纹LIFT Lift Type 升降式LJ Lap Joint 搭接LJF Lap Joint Flange 松套法兰LO Locked Open 在开启状态下锁定L.P. Low Pressure 低压LR Long Radius 长半径LRE Long Radius Elbow 长半径弯头LTG Large Tongue & Groove 大椎槽MMA TL Material 材料MAX Maximum 最大MB Machine Bolt 机器螺栓（单头）MF Male and Female 凸和凹MFG Manufacture 制造MF *Manufacture 制造厂MH Manhole 人孔MI Malleable Iron 可锻铸铁MIN *Minimum 最小MJ Mechanical Joint 机械接头M.L Match Line 连续线MSS * Manufacturers StandardizationSociety of the Valve andFittings Industry, Inc.美国阀门和管件制造商标准化协会MTO Material take-off 材料统计MW Minimum Wall 最小壁厚M.W. Mineral Wool 矿（物）棉NN *North 北NB Nominal Bore 公称孔径N.B. Non-Bonnet 无阀盖NC Normally Closed 常闭NIP Nipple 短管NO Normally Open; 常开*Number号；数量NO INS No Insulation 不隔热NOM Nominal 公称的；额定的NOZ Nozzle 管口NPS Nominal Pipe Size 公称管径NPSH Net Positive Suction Head 净正吸入压头NPT *American National Taper 美国锥管螺纹Pipe ThreadNS Nominal Size 公称直径 NV Needle Valve 针形阀OOD *Outside Diameter 外径 OET One end Threaded 一端带螺纹 OR Outside Radius 外半径 ORF Orifice 孔板 ORIENT Orientation 方位OS & Y Outside Screw and Yoke 外螺纹阀杆和阀轭OSNB Outside Screw Non-Bonnet 外螺纹无阀盖PP Plug 堵头PAP Piping Arrangement Plan 管道布置平面图PB Pressure Seal Bonnet 压力密封的阀盖 P-B Plain End –Bevel End 平端—坡口端 PC Pressure Seal Cap 压力密封的阀帽 P.C.D. Pitch Circle Diameter 节圆直径 Pcs 个PE Plain End (not beveled) 平端（无坡口） PF Platform 平台PID Piping & Instrument Diagram 管道及仪表流程图PN *Nominal Pressure 公称压力 PN Plant North 工厂北向 POS point of Support 支承点 P-P Plain End —Plain End 两端为平端 PREP Preparation 加工准备 PSIA *Pounds Per Square Inch Absolute 磅/（绝）英寸2 PSIG Pounds Per Square Inch Gage 磅/（表）英寸2PT Point 点PTFE *Polytetrafluoroethylene 聚四氟乙烯 PT.NO Part No. 件号 PV Plug Valve 旋塞阀PVC *Poly Vinyl Chloride 聚氯乙烯QQTY *Quantity 数量RR *Radius 半径 RED Reducer 异径管 REF Reference 参考 REINF Reinforce 加强 REQD Required 需要；申请 REV *Revision 修改 RF Raised Face 凸面 RG Ring Gasket 环形垫片R.H.THD Right Hand Thread 右螺旋 RJ Ring Joint 环垫接头 RO Restriction Orifice 限流孔板 RPM *Revolutions Per Minute 转/分 RPS *Revolutions Per Second 转/秒 RS Resting Support 支承架，滑动架 RTJ Ring Type Joint （见RJ ） RV Relief Valve 安全泄液阀SS *South 南S Spring 弹簧（管架用）SAW (Automatic)Submerged Arc Welding 自动埋弧焊SB Stud Bolt 双头螺栓 SB Screwed Bonnet 螺纹阀盖 SC Sample Cooler 取样冷却器 SCH *Schedule 管壁厚系列号 SCRD Screwed 螺纹SEP Small end Plain 小端为平的 SET Small end Threaded 小端带螺纹SF Semi-Finished 半光SG Sight Glass 视镜SH Surface Hard Facing 硬质密封面SK Sketch 草图SMAW Shielded Metal Arc Welding 有保护的金属电弧焊SMLS Seamless 无缝SN Swaged Nipple 异径短管SO Slip – On 滑套SOF Slip – On Flange 滑套法兰SPEC *Specification 规定，说明SPL Sound Pressure Lever 升压水准SQ *Square 方的，平方SR Shout Radius 短半径SRE Short Radius Elbow 短半径弯头SS *Stainless Steel 不锈钢ST Steam Trap 蒸汽疏水阀STD *Standard 标准STG Small Tongue & Groove 小椎槽面STL *Steel 钢STM Steam 蒸汽STM.TR Steam Tracing 蒸汽拌热SUCT Suction 吸入口SV Safety Valve 安全泄气阀SW Socket Weld 承插焊SWG Swage 锻造，模锻SWMG Swing Type 旋启式SYM Symmetrical 对称的TT Tee 三通TE Threaded End 螺纹端TEMP *Temperature 温度TG Tongue & Groove 椎槽THD *Threaded 螺纹的THK *Thickness 厚度TL Tangent Line 切线TN True North 真实北向TOC Top of Concrete 混凝土北向TOP Top of pipe 管顶TOS Top of Support 支架顶面Top of Steel 钢结构顶面TYP Typical 典型的UUB Union Bonnet 带活接头的阀盖UC Union Cap 带活接头的阀帽UN Union 活接头VV Valve 阀V AC Vacuum 真空V AR Variable 可变的VERT Vertical 垂直的VOL *V olume 卷，册，容量，体积WW *West 西WB Weld Branch 焊接支管WC Weld Cap 焊接管帽WD Width 宽度WE Weld End 焊接端WL Welding Line 焊接线WN Welding Neck 对焊法兰（颈部）WNF Weld Neck Flange 对焊法兰WP Working Pressure 工作压力W.P. Working Point 工作点WT Wall Thickness 壁厚Weight 重量XXH Extra Heavy 加强的，加厚的XXH Double Extra Heavy 双倍加强（厚）的XS Extra Strong 加强的XXS Double Extra Strong 双倍加强的YYP Yield Point 屈服点A——公称直径单位为mm L Angle(L Shape)角钢B——公称直径单位为IN [Channel([Shape)槽钢LBS Pounds 磅I I —Beam 工字钢ΦDiameter 直径WF Wide Flange 宽缘工字钢φCenter Line 中心线R Plate 钢板英寸#Pounds Per Square Inch 磅/2#（为于阿拉伯数字的左上角）Number 号。
工艺标准管道英文代号及其缩写
石油天然气工艺管道安装常用英语缩写1、SWAGED NIPPLE CONC SMLS.：大小头同心无缝2、BLE/PSE：Beveled Large End/Plain Small End 大端开破口/小端平端3、PE/PE、PBE、BLE/PSE、BSE/PLE：平端/平端、两端平端、大端开破口/小端平端、小端开破口/大端平端4、ELBOW 90 DEG LR BW SMLS.：弯头 90度长半径（R=1.5DN）对焊无缝5、PIPE SMLS PE/BE：无缝管平口/坡口6、GASKET FLAT RING：垫圈平面环形7、compressed asbestos fiber jointing sheet：石棉胶板8、SPECTACLE BLIND：8字盲板9、STUDBOLT ALLOY STEEL：双头螺栓合金钢10、SR ：短半径（R=1.0DN）11、Mild Steel 软钢; 低碳钢软钢丝12、Mild Steel Arc Welding Electrode 低碳钢焊条13、Mild Steel Channel 槽钢14、Mild Steel Checkered Plate 花纹钢板15、Mild Steel Equal Angle 等边角钢16、Mild Steel Expanded Sheets 钢板网17、Mild Steel Fire Box 软钢板火箱18、Mild Steel Hexagonal Bolts 六角螺丝梗19、Mild Steel Hexagonal Bolts And Nuts 六角螺丝闩20、Mild Steel I-Beam 低碳工字钢21、Mild Steel Ingot 低碳钢锭22、Mild Steel Plate 软钢板23、Mild Steel Reinforcement (含钢量0.12--0.25%) 软钢钢筋24、Mild Steel Shank 软钢手柄25、Mild Steel Sheet 软钢皮26、TS：螺母（nut的复数）27、BOLT：螺栓28、FULL BORE：与管子等径的、直通式（Valve Ball, Full Bore全通径球阀）29、REDUCED/REGULAR BORE：缩径（Valve Ball, Reduced/Regular Bore缩径球阀）30、SW ENDS / CARBON STEEL BODY / DIMS TO BS EN：承插焊/碳钢阀体/尺寸按照英国及欧洲标准31、RF FLANGED ENDS：凸面法兰连接（表示阀门连接形式）32、TEE EQUAL：等径三通33、SOCKOLET：承插支管台34、THREBOLET：螺纹支管台35、常见阀门连接面英文表示：⑴ LUGGED ------>凸耳对夹式的,法门的一种结构形式.一般用于大直径的止回阀或蝶阀,属于对夹连接的一个变种,要配对法兰.连接螺栓要加长⑵ RING TYPE JOINT------>环连接面,这是法兰密封面的类型,一般这样写要法兰的.⑶ SOCKET WELD------>承插焊连接,不需法兰⑷ THREADED---->螺纹连接,不要法兰⑸ WAFER------>对夹式连接,类似于凸耳的,也是一种阀门的结构形式,属于FLANGELESS 阀门,阀门本体没有法兰,但是要有配对法兰连接.螺栓要加长⑹ BUTTERWELD/THREADED------>对焊/罗纹.都不要法兰,一般是用于描述小阀门,两端的连接形式不同的情况⑺ SOCKET WELD /THREADED--->承插焊/螺纹,都不要法兰,一般是用于描述小阀门,两端的连接形式不同的情况36、VALVE GATE / SOLID WEDGE：闸阀/整体楔形闸板37、MANUFACTURERS STANDARD：行业标准38、union：通常指的是活接头，也就是老师傅常说的“油印”；nipple：一般是指用于软管站连接软管的接头，连接方式为多样（焊接／丝接／法兰连接）；pipe：一般就指短管，其中的couple特指两头带法兰的短管连接，即俗称的“车轱辘管”。
华三路由器软件升级指南
清洗剂系列表面活性剂(1)
5-20%使用和DF-21搭配即是高档清洗剂
进口
AEC
醇醚羧酸盐
50KG/桶
6-7
进口
XW-100
增溶剂
200KG/桶
6-9
增加无机盐在表面活性剂中溶解度
本厂
W—10
缓蚀剂
50KG/桶
6-9
在碱性清洗剂中起缓蚀作用避免金属腐蚀
本厂
SW—10
缓蚀剂
25KG/桶
6-7
在酸洗过程中防止酸过腐蚀伤害基材
本厂
W-10A
缓蚀剂
25KG/桶
9-11
防止碱性清洗过程中过腐蚀
进口
渗透剂TA
200KG/桶
6-7
金属清洗剂乳化剂渗透剂
上海
6503
净洗剂
200KG/桶
8-9
定产
6501
净洗剂
200KG/桶
8-9
辽宁
三乙醇胺
220KG/桶
8-10
进口
一乙醇胺
215KG/桶
8-10
进口
特乙胺
200KG/桶
8-10
吉化
深圳新葳科技
清洗剂系列表面活性剂
产地
产品编号
产品名称
包装规格
PH
简要说明
本厂
WS—100
清洗剂
25KG.桶
8-10
5-10%使用，适合搞精密零部件清洗，无毒无污染，配合超神波清洗效果更佳
本厂
AL—80
纯铝清洗剂
25KG
2-5
适合清洗散热片表面发白除油，表面脱氧
进口
CF-60
聚醚多元醇3300IN
200KG/桶
工艺管道英文代号及缩写
石油天然气工艺管道安装常用英语缩写1、SWAGED NIPPLE CONC SMLS.：大小头同心无缝2、BLE/PSE：Beveled Large End/Plain Small End 大端开破口/小端平端3、PE/PE、PBE、BLE/PSE、BSE/PLE：平端/平端、两端平端、大端开破口/小端平端、小端开破口/大端平端4、ELBOW 90 DEG LR BW SMLS.：弯头 90度长半径（R=1.5DN）对焊无缝5、PIPE SMLS PE/BE：无缝管平口/坡口6、GASKET FLAT RING：垫圈平面环形7、compressed asbestos fiber jointing sheet：石棉胶板8、SPECTACLE BLIND：8字盲板9、STUDBOLT ALLOY STEEL：双头螺栓合金钢10、SR ：短半径（R=1.0DN）11、Mild Steel 软钢; 低碳钢软钢丝12、Mild Steel Arc Welding Electrode 低碳钢焊条13、Mild Steel Channel 槽钢14、Mild Steel Checkered Plate 花纹钢板15、Mild Steel Equal Angle 等边角钢16、Mild Steel Expanded Sheets 钢板网17、Mild Steel Fire Box 软钢板火箱18、Mild Steel Hexagonal Bolts 六角螺丝梗19、Mild Steel Hexagonal Bolts And Nuts 六角螺丝闩20、Mild Steel I-Beam 低碳工字钢21、Mild Steel Ingot 低碳钢锭22、Mild Steel Plate 软钢板23、Mild Steel Reinforcement (含钢量0.12--0.25%) 软钢钢筋24、Mild Steel Shank 软钢手柄25、Mild Steel Sheet 软钢皮26、TS：螺母（nut的复数）27、BOLT：螺栓28、FULL BORE：与管子等径的、直通式（Valve Ball, Full Bore全通径球阀）29、REDUCED/REGULAR BORE：缩径（Valve Ball, Reduced/Regular Bore缩径球阀）30、SW ENDS / CARBON STEEL BODY / DIMS TO BS EN：承插焊/碳钢阀体/尺寸按照英国及欧洲标准31、RF FLANGED ENDS：凸面法兰连接（表示阀门连接形式）32、TEE EQUAL：等径三通33、SOCKOLET：承插支管台34、THREBOLET：螺纹支管台35、常见阀门连接面英文表示：⑴ LUGGED ------>凸耳对夹式的,法门的一种结构形式.一般用于大直径的止回阀或蝶阀,属于对夹连接的一个变种,要配对法兰.连接螺栓要加长⑵ RING TYPE JOINT------>环连接面,这是法兰密封面的类型,一般这样写要法兰的.⑶ SOCKET WELD------>承插焊连接,不需法兰⑷ THREADED---->螺纹连接,不要法兰⑸ WAFER------>对夹式连接,类似于凸耳的,也是一种阀门的结构形式,属于FLANGELESS 阀门,阀门本体没有法兰,但是要有配对法兰连接.螺栓要加长⑹ BUTTERWELD/THREADED------>对焊/罗纹.都不要法兰,一般是用于描述小阀门,两端的连接形式不同的情况⑺ SOCKET WELD /THREADED--->承插焊/螺纹,都不要法兰,一般是用于描述小阀门,两端的连接形式不同的情况36、VALVE GATE / SOLID WEDGE：闸阀/整体楔形闸板37、MANUFACTURERS STANDARD：行业标准38、union：通常指的是活接头，也就是老师傅常说的“油印”；nipple：一般是指用于软管站连接软管的接头，连接方式为多样（焊接／丝接／法兰连接）；pipe：一般就指短管，其中的couple特指两头带法兰的短管连接，即俗称的“车轱辘管”。
WNG-100逆功率监控装置说明书V1.01
b. 功率测量误差不超过额定值的±1%;
c. 开关量输入电压（DC24V），分辨率不大于 2ms；
d. 脉冲量输入电压（DC24V），脉冲宽度不小于 20ms。
2.10 触点容量
a. 在电压不大于 250V，电流不大于 1A，时间常数 I/r 为 5ms±0.75ms 的直流有感负荷电
路中，触点断开容量为 50W，长期允许通过电流不大于 5A。
b. 快速瞬变干扰试验：能承受 GB/T14598.10－2007 第四章规定的严酷等级为 A 级的快速
瞬变干扰试验。
c. 辐射电磁场干扰试验：能承受 GB/T14598.9－2002 第四章规定的严酷等级的辐射电磁
场干扰试验。
d. 静电放电试验：能承受 GB/T14598.14-1998 中 4.1 规定的严酷等级为Ⅲ级的静电放电
检测交流电网（AC400V，50Hz）供电回路三相电压、电流（测量点），判断功率流向和功 率大小。如果电网供电回路出现逆功率现象，当逆功率值大于逆功率定值（可设定，单位 W 二次功率值）时，按照各个出口延时时限的不同，当延时超过相应出口的延时后，驱动该出 口动作，跳闸顺序为先跳出口 1，再跳出口 2，依次类推， 逐级断开清洁电源并网系统中 8 个模组，直到逆功率现象消失。（需要清洁电源的控制开关提供分合闸操作回路）。保护原理 如图 1 所示。
WNG-100 微机逆功率监控装置
WNG-100 逆功率监控装置
1 装置简介 WNG-100 逆功率监控装置（以下简称装置）主要针对部分并网型光伏发电站，这部分并
网电站所谓并网其实只是与电网接通，并非发电输送电网，白天用户光伏所发电量主要供自 己厂区内的用电负荷使用，晚上没有光伏发电时仍旧需要使用电网所输电量，因此才并网的。 这类光伏电站要求在并网处加以控制，尽量使光伏发电量刚好满足厂区内的用电负荷使用。 1.1 功能配置
管件的各种英文缩写
管件的各种英文缩写管道英文缩写A Anchor 固定ABS *Absolute 绝对的AISI *American Iron andSteel Institute 美国钢铁学会ANSI *American NationalStandards Institute 美国国家标准学会API *American Petroleum Institute 美国石油学会APPROX *Approximate 大约，近似的ASB Asbestos 石棉ASME *American Society Of Mechanical Engineers美国机械工程师协会ASSY *Assembly 装配，组装ASTM *American Society OfTesting Material 美国材料实验协会ATM *Atmosphere 大气压AWG *American Wire Gage 美国线规AWS *American Wel**** Society 美国焊接协会AWWA *American Water WorksAssociation 美国水工协会BBB Bolted Bonnet 栓柱连接的阀盖BB By Buyer 买方供货B-B Beveled End-Beveled End 两端为坡口端BC Bolt Circle 螺栓中心圆B.C Bolted Cover(cap) 螺栓连接的阀兰盖（帽）BE Beveled End (for wel****) 坡口（焊接用）B.E Bell End 承口BEP Both Ends Plain 两端平BET Both Ends Threaded 两端带螺纹BL Battery Limit 装置区边界BF Blind Flange 盲板法兰BLD Blind 盲板BLDG *Buil**** 建筑物BM Bill Of Material 材料表BOP Bottom Of Pipe 管底B-P Beveled End —Plain End 坡口端.平端BV Butterfly valve 蝶阀BWG * Birmingham Wire Gage 伯明翰线规BW Butt Weld 对焊CC Cap 管帽C-C Center to Center 中至中C-E Center to End 中至端面C-F Center to Face 中至面CH-OP Chain Operated 链条操纵的CH.PL Checkered Plate 花纹钢管C.I *Cast Iron 铸铁CL *Class 英制压力等级，等级，种类CLEAR Clearance 间隙COD Continued on Drawing 接续图COL *Column 柱，塔CONC Concentric 同心的CONN Connection 连接，接口CONT *Continue 连续CONT.V. Control Valve 控制阀CPLG Coupling 管接头，连轴节C.R. Concentric Reducer 同心异径管C.S. *Carbon Steel 碳钢C.S. Cold Spring 冷紧C.S.C. Car Seal Close 在关闭状态下封住C.S.O. Car Seal Open 在开启状态下封住CUST Customer 客C.V Check Valve 止回阀DDEG *Degree 度DF Drain funnel 排液漏斗DIA *Diameter 直径DIM *Dimension 尺寸DISCH *Discharge 出口，排出Diaphragm VELVE 隔膜阀DMF Double Male And Female 双重凹凸DN Norminal Diameter公称直径DN Down 下DR Drain 排液DS Directional Stop 定向限为架DWG *Drawing 图EE *East 东EC External Coating 外面涂防腐层ECC Eccentric 偏心EFW Electric Fusion Welded 电容焊的EL(ELEV) *Elevation 标高；立面ELL Elbow 弯头EQIOP Equipment 设备，装置EQUIV Equivalent 相当的E.R. Eccentric Reducer 偏心异经管ERW Electric Resistance Welded 电阻焊的EW Eye Washer & Shower 洗眼器及淋浴器EXP.JT Expansion Joint 膨胀节FFDN Foundation 基础FF Flat Faced Or Full Faced 全平面；满平面F-F Face To Face 面至面FGW Fusion Gas Wel**** 气熔焊FIG *Figure 图FL Floor 楼面FLEX TUBE Flexible Tube 挠性管FLG Flange 法兰FLGD Flanged 法兰式的FLGF Flanged Face 法兰面FOB Flat On Bottom 底面平FOT Flat On Top 顶面平FP Fix Point 固定点FS Forged Steel 锻钢FTF Fitting To Fitting 管件直连FTG Fitting 管件FURND Furnished 提供的，装设的FW Field Weld 现伤焊GG Guide 导向GA *Gage 表，表压，规（线规）GALV *Galvanize 镀锌GL Ground Level 地面GLV Globe Valve 截止阀GEAR OP Gear Operated 齿轮传动的GMAW Gas Metal Arc Wel**** 金属极惰气体保护焊GSKT Gasket 垫片GTAW (Inert)Gas Tungsten Arc Wel**** 惰性气体保护钨极电弧焊GV Gate Valve 闸阀HH Hanger 吊架HC Hose Connection 软管接头H.CPLG Half Coupling 半节管接头HDR Header 总管HEX *Hexagon 六角形HF Hard Alloy Face on阀内件（阀心）为Valve Trim 硬质合金密封面HH Hand Hole 手孔HOR Horizontal 水平的H.P *High Pressure 高压HS Hose Station 软管IID *Inside Diameter 内径IN *Inch 英寸INS Insulation 隔热INST Instrument 仪表INV Invert (inside bottom of pipe) 管子内底IPS Iron Pipe size 铁管尺寸ISO Isometric Drawing 周测图（空视图）I.S.B.L Inside Battery Limit 装置边界内恻ISNS Inside screw & Non-rising Stem 内螺纹非升杆ISRS Inside screw & Rising stem 内螺纹升杆JJT Joint 接头JS Jack Screw 顶开（起）螺栓LLC Locked Closed 在关闭状态下锁定LEP Large end plain 大端为平的LET Large end Threaded 大端带螺纹LG Long 长LGF Lens Gasket Face 透镜垫连接面L.H.THD Left Hand Thread 左螺纹LIFT Lift Type 升降式LJ Lap Joint 搭接LJF Lap Joint Flange 松套法兰LO Locked Open 在开启状态下锁定L.P. Low Pressure 低压LR Long Radius 长半径LRE Long Radius Elbow 长半径弯头LTG Large Tongue & Groove 大椎槽MMATL Material 材料MAX Maximum 最大MB Machine Bolt 机器螺栓（单头）MF Male and Female 凸和凹MFG Manufacture 制造MF *Manufacture 制造厂MH Manhole 人孔MI Malleable Iron 可锻铸铁MIN *Minimum 最小MJ Mechanical Joint 机械接头M.L Match Line 连续线MSS * Manufacturers Standardization Society of the Valve and Fittings Industry, Inc.美国阀门和管件制造商标准化协会MTO Material take-off 材料统计MW Minimum Wall 最小壁厚M.W. Mineral Wool 矿（物）棉NN *North 北NB Nominal Bore 公称孔径N.B. Non-Bonnet 无阀盖NC Normally Closed 常闭NIP Nipple 短管NO Normally Open; 常开*Number号；数量NO INS No Insulation 不隔热NOM Nominal 公称的；额定的NOZ Nozzle 管口NPS Nominal Pipe Size 公称管径NPSH Net Positive Suction Head 净正吸入压头NPT *American National Taper 美国锥管螺纹Pipe ThreadNS Nominal Size 公称直径NV Needle Valve 针形阀OOD *Outside Diameter 外径OET One end Threaded 一端带螺纹OR Outside Radius 外半径ORF Orifice 孔板ORIENT Orientation 方位OS & Y Outside Screw and Yoke 外螺纹阀杆和阀轭OSNB Outside Screw Non-Bonnet 外螺纹无阀盖PP Plug 堵头PAP Piping Arrangement Plan 管道布置平面图PB Pressure Seal Bonnet 压力密封的阀盖P-B Plain End –Bevel End 平端—坡口端PC Pressure Seal Cap 压力密封的阀帽P.C.D. Pitch Circle Diameter 节圆直径PE Plain End (not beveled) 平端（无坡口）PF Platform 平台PID Piping & Instrument Diagram管道及仪表流程图PN *Nominal Pressure 公称压力PN Plant North 工厂北向POS point of Support 支承点P-P Plain End—Plain End 两端为平端PREP Preparation 加工准备PSIA *Pounds Per Square InchAbsolute 磅/PSIG Pounds Per Square Inch Gage 磅/PT Point 点PTFE *Polytetrafluoroethylene 聚四氟乙烯PT.NO Part No. 件号PV Plug Valve 旋塞阀PVC *Poly Vinyl Chloride 聚氯乙烯QQTY *Quantity 数量RR *Radius 半径RED Reducer 异径管REF Reference 参考REINF Reinforce 加强REQD Required 需要；申请REV *Revision 修改RF Raised Face 凸面RG Ring Gasket 环形垫片R.H.THD Right Hand Thread 右螺旋RJ Ring Joint 环垫接头RO Restriction Orifice 限流孔板RPM *Revolutions Per Minute 转/分RPS *Revolutions Per Second 转/秒RS Resting Support 支承架，滑动架RTJ Ring Type Joint（见RJ）RV Relief Valve 安全泄液阀SS *South 南S Spring 弹簧（管架用）SAW (Automatic)Submerged Arc Wel**** 自动埋弧焊SB Stud Bolt 双头螺栓SB Screwed Bonnet 螺纹阀盖SC Sample Cooler 取样冷却器SCH *Schedule 管壁厚系列号SCRD Screwed 螺纹SEP Small end Plain 小端为平的SET Small end Threaded 小端带螺纹SF Semi-Finished 半光SG Sight Glass 视镜SH Surface Hard Facing 硬质密封面SK Sketch 草图SMAW Shielded Metal Arc Wel**** 有保护的金属电弧焊SMLS Seamless 无缝SN Swaged Nipple 异径短管SO Slip – On 滑套SOF Slip – On Flange 滑套法兰SPEC *Specification 规定，说明SPL Sound Pressure Lever 升压水准SQ *Square 方的，平方SR Shout Radius 短半径SRE Short Radius Elbow 短半径弯头SS *Stainless Steel 不锈钢ST Steam Trap 蒸汽疏水阀STD *Standard 标准STG Small Tongue & Groove 小椎槽面STL *Steel 钢STM Steam 蒸汽STM.TR Steam Tracing 蒸汽拌热SUCT Suction 吸入口SV Safety Valve 安全泄气阀SW Socket Weld 承插焊SWG Swage 锻造，模锻SWMG Swing Type 旋启式SYM Symmetrical 对称的TT Tee 三通TE Threaded End 螺纹端TEMP *Temperature 温度TG Tongue & Groove 椎槽THD *Threaded 螺纹的THK *Thickness 厚度TL Tangent Line 切线TN True North 真实北向TOC Top of Concrete 混凝土北向TOP Top of pipe 管顶TOS Top of Support 支架顶面Top of Steel 钢结构顶面TYP Typical 典型的UUB Union Bonnet 带活接头的阀盖UC Union Cap 带活接头的阀帽UN Union 活接头VV Valve 阀VAC Vacuum 真空VAR Variable 可变的VERT Vertical 垂直的VOL *Volume 卷，册，容量，体积WW *West 西WB Weld Branch 焊接支管WC Weld Cap 焊接管帽WD Width 宽度WE Weld End 焊接端WL Wel**** Line 焊接线WN Wel**** Neck 对焊法兰（颈部）WNF Weld Neck Flange 对焊法兰WP Working Pressure 工作压力W.P. Working Point 工作点WT Wall Thickness 壁厚Weight 重量XXH Extra Heavy 加强的，加厚的XXH Double Extra Heavy 双倍加强（厚）的XS Extra Strong 加强的XXS Double Extra Strong 双倍加强的YYP Yield Point 屈服点。
第四部分湿度测量
第四节 高分子湿度传感器
一．高分子电容式湿度传感器
C S / d
根据电容公式可知，在 电容两个极板旳面积和 间距不变旳情况下，当 介电常数发生变化时将 引起电容值旳变化。
一．高分子电容式湿度传感器
特点：迅速吸湿、脱湿，滞后小，响应快， 不受气流速度影响，测量范围宽，抗污染能 力强，稳定性好。
一．高分子电容式湿度传感器
1．一般干湿球温度计
构造 同精度温度计两支、脱脂纱布、 蒸馏水
特点 无风速控制，无屏蔽辐射 水易污染 测量误差较大
注意： ①湿球温度计安装时，要求温度计旳球 部离开水杯上沿至少2～3cm， ②应使湿球温度计周围空气流速保持在 2.5m/s以上，使A为常数。
Tw Ts
通风干湿球温度计（阿斯曼）
环境温度对输出影响较大，所以要进行温度补偿。
最高使用温度55℃，当不小于55℃，氯化锂溶液 轻易蒸发。
扩大氯化锂湿度计旳测量范围
r
r
r
r
A
RAB=f()
B
R4
R3
R2
R1
75~95% 55~75% 35~55% 15~35%
扩大氯化锂湿度计旳测量范围
电阻(K )
(%) 15 35 55 75 95
二．高分子电阻式湿度传感器
使用高分子固体电解质 材料制作感湿膜，当相 对湿度大时，膜中旳可 移动离子浓度增大，电 阻降低，当相对湿度降 低时，膜中旳可运动离 子浓度降低，电阻阻值 增大。这么可经过电极 间旳电阻值旳变化测量 相对湿度。
二．高分子电阻式湿度传感器
HPR-MQ-M52R
（M52R）是一款环境 保护型旳高分子湿度传 感器。在空调、加湿器、 除湿机等民用家电产品 中得到了广泛旳应用。
管件的各种英文缩写
管件的各种英文缩写管道英文缩写A Anchor 固定ABS *Absolute 绝对的AISI *American Iron andSteel Institute 美国钢铁学会ANSI *Americ an NationalStandards Institute 美国国家标准学会API *Americ an Petroleum Institute 美国石油学会APPR OX *Appr oximate 大约，近似的ASB Asbestos 石棉ASME *American Society Of Mechanical Engineers美国机械工程师协会ASSY *Assembly 装配，组装ASTM *American Society OfTesting Material 美国材料实验协会ATM *Atmospher e 大气压AW G *American Wire Gage 美国线规AW S *American Wel**** Society 美国焊接协会AWW A *Americ an W ater Wor ksAssociation 美国水工协会BBB Bolted Bonnet 栓柱连接的阀盖BB By Buyer买方供货B-B Beveled End-Beveled End 两端为坡口端BC Bolt C ircle 螺栓中心圆B.C Bolted Cover(cap) 螺栓连接的阀兰盖（帽）BE Beveled End (for wel****) 坡口（焊接用）B.E Bell End 承口BEP Both Ends Plain 两端平BET Both Ends Threaded 两端带螺纹BL Batter y Limit 装置区边界BF Blind Flange 盲板法兰BL D Blind 盲板BL DG *Bui l**** 建筑物BM Bill Of Material 材料表BOP Bottom Of Pipe 管底B-P Beveled End —Plain End 坡口端.平端BV Butterfly valve 蝶阀BW G * Bir mingham Wire Gage 伯明翰线规BW Butt Weld 对焊CC Cap 管帽C-C Center to Center中至中C-E Center to End 中至端面C-F Center to Fac e 中至面CH-OP Chain Operated 链条操纵的CH.PL Chec kered Plate 花纹钢管C.I *Cast Iron 铸铁C L *Class 英制压力等级，等级，种类C L EAR Clearanc e 间隙COD Continued on Dr aw ing 接续图CO L *Column 柱，塔CONC Conc entric 同心的CONN Connection 连接，接口CONT *Continue 连续CONT.V. Control Valve 控制阀CPL G Coupling 管接头，连轴节C.R. Concentric Reducer同心异径管C.S. *Car bon Steel 碳钢C.S. Cold Spring 冷紧C.S.C. Car Seal Close 在关闭状态下封住C.S.O. Car Seal Open 在开启状态下封住CUST Customer 客C.V Check Valve 止回阀DDEG *Degree 度DF Drain funnel 排液漏斗DIA *Diameter直径DIM *Dimension 尺寸DISCH *Discharge 出口，排出Diaphragm VEL VE 隔膜阀DMF Double Male And Female 双重凹凸DN Nor minal Diameter公称直径DN Down 下DR Drain 排液DS Directional Stop 定向限为架DW G *Drawing 图EE *East 东EC External Coating 外面涂防腐层ECC Ecc entric 偏心EFW Electric Fusion Welded 电容焊的EL(ELEV) *Elevation 标高；立面ELL Elbow 弯头EQI OP Equipment 设备，装置EQUI V Equi valent 相当的E.R. Eccentric Reduc er 偏心异经管ERW Electric Resistanc e Welded 电阻焊的EW Eye W asher & Shower 洗眼器及淋浴器EX P.JT Expansion Joint 膨胀节FFDN Foundation 基础FF Flat F ac ed Or Full Fac ed 全平面；满平面F-F Face To Fac e 面至面FGW Fusion Gas Wel**** 气熔焊FIG *F igure 图F L Floor楼面F L EX TUBE Flexible Tube 挠性管F LG F lange 法兰F L GD F langed 法兰式的F L GF Flanged Fac e 法兰面FOB Flat On Bottom 底面平FOT F lat On Top 顶面平FP F ix Point 固定点FS Forged Steel 锻钢FTF Fitting To Fitting 管件直连FTG F itting 管件FURND Furnished 提供的，装设的FW F ield Weld 现伤焊GG Guide 导向GA *Gage 表，表压，规（线规）GAL V *Galvanize 镀锌GL Gr ound Level 地面GL V Globe Valve 截止阀GEAR OP Gear Operated 齿轮传动的GMAW Gas Metal Arc Wel**** 金属极惰气体保护焊GSKT Gasket 垫片GTAW (Inert)Gas Tungsten A rc Wel**** 惰性气体保护钨极电弧焊GV Gate Valve 闸阀HH Hanger 吊架HC Hose Connection 软管接头H.CPL G Half Coupling 半节管接头HDR Header 总管HEX *Hexagon 六角形HF Har d Alloy Face on阀内件（阀心）为Valve Trim 硬质合金密封面HH Hand Hole 手孔HOR Horizontal 水平的H.P *High Pr essure 高压HS Hose Station 软管IID *Inside Diameter 内径IN *Inc h 英寸INS Insulation 隔热INST Instr ument 仪表INV Invert (inside bottom of pipe) 管子内底IPS Iron Pipe size 铁管尺寸ISO Isometric Drawing 周测图（空视图）I.S.B.L Inside Batter y Limit 装置边界内恻ISNS Inside screw & Non-rising Stem 内螺纹非升杆ISRS Inside screw & Rising stem 内螺纹升杆JJT Joint 接头JS Jack Screw 顶开（起）螺栓LLC Locked Closed 在关闭状态下锁定LEP Lar ge end plain 大端为平的LET Large end Threaded 大端带螺纹LG Long 长LGF Lens Gasket Face 透镜垫连接面L.H.THD Left Hand Thread 左螺纹LIFT Lift Type 升降式LJ Lap Joint 搭接LJF Lap Joint F lange 松套法兰L O Locked Open 在开启状态下锁定L.P. Low Pressure 低压LR Long Radius 长半径LRE Long Radius Elbow 长半径弯头LTG Large Tongue & Groove 大椎槽MMATL Material 材料MAX Maximum 最大MB Machi ne Bolt 机器螺栓（单头）MF Male and Female 凸和凹MFG Manufactur e 制造MF *Manufactur e 制造厂MH Manhole 人孔MI Malleable Iron 可锻铸铁MIN *Mini mum 最小MJ Mechanical Joint 机械接头M.L Matc h Line 连续线MSS * Manufacturers Standardization Society of the Valve and F ittings Industr y, Inc.美国阀门和管件制造商标准化协会MTO Material take-off 材料统计MW Mini mum W all 最小壁厚M.W. Miner al W ool 矿（物）棉NN *North 北NB Nominal Bore 公称孔径N.B. Non-Bonnet 无阀盖NC Normally Closed 常闭NIP Nipple 短管NO Normally Open; 常开*Number号；数量NO INS No Insulation 不隔热NOM Nominal 公称的；额定的NOZ Nozzle 管口NPS Nominal Pipe Size 公称管径NPSH Net Positive Suction Head 净正吸入压头NPT *American National Taper 美国锥管螺纹Pipe ThreadNS Nominal Size 公称直径NV Needle Valve 针形阀OOD *Outside Diameter 外径OET One end Threaded 一端带螺纹OR Outside Radius 外半径ORF Orific e 孔板ORIENT Orientation 方位OS & Y Outside Scr ew and Yoke 外螺纹阀杆和阀轭OSNB Outside Screw Non-Bonnet 外螺纹无阀盖PP Plug 堵头PAP Piping A rr angement Plan 管道布置平面图PB Pr essur e Seal Bonnet 压力密封的阀盖P-B Plain End –Bevel End 平端—坡口端PC Pr essur e Seal Cap 压力密封的阀帽P.C.D. Pitch Circle Diameter 节圆直径PE Plain End (not beveled) 平端（无坡口）PF Platfor m 平台PID Piping & Instrument Diagram管道及仪表流程图PN *Nominal Pr essure 公称压力PN Plant North 工厂北向POS point of Support 支承点P-P Plain End—Plain End 两端为平端PREP Preparation 加工准备PSIA *Pounds Per Square InchAbsolute 磅/PSIG Pounds Per Square Inc h Gage 磅/PT Point 点PTFE *Polytetrafluoroethylene 聚四氟乙烯PT.NO Part No. 件号PV Plug Valve 旋塞阀PVC *Poly Vinyl Chloride 聚氯乙烯QQTY *Quantity 数量RR *Radius 半径RED Reducer 异径管REF Refer ence 参考REINF Reinforc e 加强REQD Requir ed 需要；申请REV *Revision 修改RF Raised F ac e 凸面RG Ring Gasket 环形垫片R.H.THD Right Hand Thread 右螺旋RJ Ring Joint 环垫接头RO Restriction Orifice 限流孔板RPM *Revolutions Per Minute 转/分RPS *Revolutions Per Second 转/秒RS Resti ng Support 支承架，滑动架RTJ Ring Type Joint（见RJ）RV Relief Valve 安全泄液阀SS *South 南S Spring 弹簧（管架用）SAW (Automatic)Submerged Arc W el**** 自动埋弧焊SB Stud Bolt 双头螺栓SB Scr ewed Bonnet 螺纹阀盖SC Sample Cooler 取样冷却器SCH *Schedule 管壁厚系列号SCRD Screwed 螺纹SEP Small end Plain 小端为平的SET Small end Thr eaded 小端带螺纹SF Semi-Finished 半光SG Sight Glass 视镜SH Surfac e Hard Facing 硬质密封面SK Sketch 草图SMAW Shi elded Metal Arc W el**** 有保护的金属电弧焊SML S Seamless 无缝SN Swaged Nipple 异径短管SO Slip – On 滑套SOF Slip – On Flange 滑套法兰SPEC *Specification 规定，说明SPL Sound Pressure Lever 升压水准SQ *Square 方的，平方SR Shout Radius 短半径SRE Short Radius Elbow短半径弯头SS *Stainless Steel 不锈钢ST Steam Tr ap 蒸汽疏水阀STD *Standard 标准STG Small Tongue & Gr oove 小椎槽面STL *Steel 钢STM Steam 蒸汽STM.TR Steam Tracing 蒸汽拌热SUCT Suction 吸入口SV Safety Valve 安全泄气阀SW Soc ket Weld 承插焊SW G Swage 锻造，模锻SW MG Swing Type 旋启式SYM Symmetrical 对称的TT Tee 三通TE Thr eaded End 螺纹端TEMP *Temperatur e 温度TG Tongue & Gr oove 椎槽THD *Threaded 螺纹的THK *Thickness 厚度TL Tangent Line 切线TN True North 真实北向TOC Top of Concrete 混凝土北向TOP Top of pipe 管顶TOS Top of Support 支架顶面Top of Steel 钢结构顶面TYP Typic al 典型的UUB Union Bonnet 带活接头的阀盖UC Union Cap 带活接头的阀帽UN U ni on 活接头VV Valve 阀VAC Vacuum 真空VAR Variable 可变的VERT Vertical 垂直的VO L *Volume 卷，册，容量，体积WW *West 西WB W eld Br anch 焊接支管W C W eld Cap 焊接管帽WD Width 宽度WE Weld End 焊接端WL W el**** Line 焊接线WN Wel**** Nec k 对焊法兰（颈部）WNF W eld Nec k F lange 对焊法兰WP Wor king Pr essur e 工作压力W.P. Working Point 工作点WT Wall Thic kness 壁厚W eight 重量XXH Extr a Heavy 加强的，加厚的XXH Double Extra Heavy 双倍加强（厚）的XS Extr a Strong 加强的XXS Double Extra Strong 双倍加强的YYP Yield Point 屈服点。
红旗泰(赫茨HZ)RF100系列通用经济型变频器说明书
-1-
安全注意事项
安装、运行、维护或检查之前要认真阅读本说明书。 本说明书中有关安全运行的注意事项分类成“警告”或当心。
警告 指出潜在的危险情况，如果不避免，可能导致人身伤亡。 当心 指出潜在的危险情况，如果不避免，可能导致人身轻度或中度的伤害和设备损 坏。这也可用来对不安全操作进行警戒。
图 1-1
-3-
1.3 变频器型号说明
1.4 变频器系列机型
变频型号
RF100-1-R40-GB-1 RF100-1-R75-GB-1 RF100-1-1R5-GB-1 RF100-1-2R2-GB-1 RF100-1-R75-GB-4 RF100-1-1R5-GB-4 RF100-1-2R2-GB-4 RF100-1-3R7-GB-4 RF100-1-5R5-GB-4 RF100-1-7R5-GB-4 RF100-1-011-GB-4 RF100-1-015-GB-4 RF100-1-018-GB-4 RF100-1-022-G-4 RF100-1-030-G-4 RF100-1-037-G-4 RF100-1-045-G-4 RF100-1-055-G-4 RF100-1-075-G-4
until DC Bus capacitors discharge. ●Use proper grouding techniques. ●Never connect AC power to output UVW terminal.
-2-
一、产品概况
1.1 技术特性
● 输入输出特性
◆ 输入电压范围：220V/380V压、过温、缺相、过压（流）失速保护功能
◆ 8 段速控制功能，PLC 控制功能
管件的各种英文缩写
管件的各种英文缩写管道英文缩写A Anchor 固定ABS *Absolute 绝对的AISI *American Iron andSteel Institute 美国钢铁学会ANSI *American NationalStandards Institute 美国国家标准学会API *American Petroleum Institute 美国石油学会APPROX *Approximate 大约，近似的ASB Asbestos 石棉ASME *American Society Of Mechanical Engineers美国机械工程师协会ASSY *Assembly 装配，组装ASTM *American Society OfTesting Material 美国材料实验协会ATM *Atmosphere 大气压AWG *American Wire Gage 美国线规AWS *American Wel**** Society 美国焊接协会AWWA *American Water WorksAssociation 美国水工协会BBB Bolted Bonnet 栓柱连接的阀盖BB By Buyer 买方供货B-B Beveled End-Beveled End 两端为坡口端BC Bolt Circle 螺栓中心圆B.C Bolted Cover(cap) 螺栓连接的阀兰盖（帽）BE Beveled End (for wel****) 坡口（焊接用）B.E Bell End 承口BEP Both Ends Plain 两端平BET Both Ends Threaded 两端带螺纹BL Battery Limit 装置区边界BF Blind Flange 盲板法兰BLD Blind 盲板BLDG *Buil**** 建筑物BM Bill Of Material 材料表BOP Bottom Of Pipe 管底B-P Beveled End —Plain End 坡口端.平端BV Butterfly valve 蝶阀BWG * Birmingham Wire Gage 伯明翰线规BW Butt Weld 对焊CC Cap 管帽C-C Center to Center 中至中C-E Center to End 中至端面C-F Center to Face 中至面CH-OP Chain Operated 链条操纵的CH.PL Checkered Plate 花纹钢管C.I *Cast Iron 铸铁CL *Class 英制压力等级，等级，种类CLEAR Clearance 间隙COD Continued on Drawing 接续图COL *Column 柱，塔CONC Concentric 同心的CONN Connection 连接，接口CONT *Continue 连续CONT.V. Control Valve 控制阀CPLG Coupling 管接头，连轴节C.R. Concentric Reducer 同心异径管C.S. *Carbon Steel 碳钢C.S. Cold Spring 冷紧C.S.C. Car Seal Close 在关闭状态下封住C.S.O. Car Seal Open 在开启状态下封住CUST Customer 客C.V Check Valve 止回阀DDEG *Degree 度DF Drain funnel 排液漏斗DIA *Diameter 直径DIM *Dimension 尺寸DISCH *Discharge 出口，排出Diaphragm VELVE 隔膜阀DMF Double Male And Female 双重凹凸DN Norminal Diameter公称直径DN Down 下DR Drain 排液DS Directional Stop 定向限为架DWG *Drawing 图EE *East 东EC External Coating 外面涂防腐层ECC Eccentric 偏心EFW Electric Fusion Welded 电容焊的EL(ELEV) *Elevation 标高；立面ELL Elbow 弯头EQIOP Equipment 设备，装置EQUIV Equivalent 相当的E.R. Eccentric Reducer 偏心异经管ERW Electric Resistance Welded 电阻焊的EW Eye Washer & Shower 洗眼器及淋浴器EXP.JT Expansion Joint 膨胀节FFDN Foundation 基础FF Flat Faced Or Full Faced 全平面；满平面F-F Face To Face 面至面FGW Fusion Gas Wel**** 气熔焊FIG *Figure 图FL Floor 楼面FLEX TUBE Flexible Tube 挠性管FLG Flange 法兰FLGD Flanged 法兰式的FLGF Flanged Face 法兰面FOB Flat On Bottom 底面平FOT Flat On Top 顶面平FP Fix Point 固定点FS Forged Steel 锻钢FTF Fitting To Fitting 管件直连FTG Fitting 管件FURND Furnished 提供的，装设的FW Field Weld 现伤焊GG Guide 导向GA *Gage 表，表压，规（线规）GALV *Galvanize 镀锌GL Ground Level 地面GLV Globe Valve 截止阀GEAR OP Gear Operated 齿轮传动的GMAW Gas Metal Arc Wel**** 金属极惰气体保护焊GSKT Gasket 垫片GTAW (Inert)Gas Tungsten Arc Wel**** 惰性气体保护钨极电弧焊GV Gate Valve 闸阀HH Hanger 吊架HC Hose Connection 软管接头H.CPLG Half Coupling 半节管接头HDR Header 总管HEX *Hexagon 六角形HF Hard Alloy Face on阀内件（阀心）为Valve Trim 硬质合金密封面HH Hand Hole 手孔HOR Horizontal 水平的H.P *High Pressure 高压HS Hose Station 软管IID *Inside Diameter 内径IN *Inch 英寸INS Insulation 隔热INST Instrument 仪表INV Invert (inside bottom of pipe) 管子内底IPS Iron Pipe size 铁管尺寸ISO Isometric Drawing 周测图（空视图）I.S.B.L Inside Battery Limit 装置边界内恻ISNS Inside screw & Non-rising Stem 内螺纹非升杆ISRS Inside screw & Rising stem 内螺纹升杆JJT Joint 接头JS Jack Screw 顶开（起）螺栓LLC Locked Closed 在关闭状态下锁定LEP Large end plain 大端为平的LET Large end Threaded 大端带螺纹LG Long 长LGF Lens Gasket Face 透镜垫连接面L.H.THD Left Hand Thread 左螺纹LIFT Lift Type 升降式LJ Lap Joint 搭接LJF Lap Joint Flange 松套法兰LO Locked Open 在开启状态下锁定L.P. Low Pressure 低压LR Long Radius 长半径LRE Long Radius Elbow 长半径弯头LTG Large Tongue & Groove 大椎槽MMATL Material 材料MAX Maximum 最大MB Machine Bolt 机器螺栓（单头）MF Male and Female 凸和凹MFG Manufacture 制造MF *Manufacture 制造厂MH Manhole 人孔MI Malleable Iron 可锻铸铁MIN *Minimum 最小MJ Mechanical Joint 机械接头M.L Match Line 连续线MSS * Manufacturers Standardization Society of the Valve andFittings Industry, Inc.美国阀门和管件制造商标准化协会MTO Material take-off 材料统计MW Minimum Wall 最小壁厚M.W. Mineral Wool 矿（物）棉NN *North 北NB Nominal Bore 公称孔径N.B. Non-Bonnet 无阀盖NC Normally Closed 常闭NIP Nipple 短管NO Normally Open; 常开*Number号；数量NO INS No Insulation 不隔热NOM Nominal 公称的；额定的NOZ Nozzle 管口NPS Nominal Pipe Size 公称管径NPSH Net Positive Suction Head 净正吸入压头NPT *American National Taper 美国锥管螺纹 Pipe ThreadNS Nominal Size 公称直径NV Needle Valve 针形阀OOD *Outside Diameter 外径OET One end Threaded 一端带螺纹OR Outside Radius 外半径ORF Orifice 孔板ORIENT Orientation 方位OS & Y Outside Screw and Yoke 外螺纹阀杆和阀轭OSNB Outside Screw Non-Bonnet 外螺纹无阀盖PP Plug 堵头PAP Piping Arrangement Plan 管道布置平面图PB Pressure Seal Bonnet 压力密封的阀盖P-B Plain End –Bevel End 平端—坡口端PC Pressure Seal Cap 压力密封的阀帽P.C.D. Pitch Circle Diameter 节圆直径PE Plain End (not beveled) 平端（无坡口）PF Platform 平台PID Piping & Instrument Diagram管道及仪表流程图PN *Nominal Pressure 公称压力PN Plant North 工厂北向POS point of Support 支承点P-P Plain End—Plain End 两端为平端PREP Preparation 加工准备PSIA *Pounds Per Square InchAbsolute 磅/PSIG Pounds Per Square Inch Gage 磅/ PT Point 点PTFE *Polytetrafluoroethylene 聚四氟乙烯PT.NO Part No. 件号PV Plug Valve 旋塞阀PVC *Poly Vinyl Chloride 聚氯乙烯QQTY *Quantity 数量RR *Radius 半径RED Reducer 异径管REF Reference 参考REINF Reinforce 加强REQD Required 需要；申请REV *Revision 修改RF Raised Face 凸面RG Ring Gasket 环形垫片R.H.THD Right Hand Thread 右螺旋RJ Ring Joint 环垫接头RO Restriction Orifice 限流孔板RPM *Revolutions Per Minute 转/分RPS *Revolutions Per Second 转/秒RS Resting Support 支承架，滑动架RTJ Ring Type Joint（见RJ）RV Relief Valve 安全泄液阀SS *South 南S Spring 弹簧（管架用）SAW (Automatic)Submerged Arc Wel**** 自动埋弧焊SB Stud Bolt 双头螺栓SB Screwed Bonnet 螺纹阀盖SC Sample Cooler 取样冷却器SCH *Schedule 管壁厚系列号SCRD Screwed 螺纹SEP Small end Plain 小端为平的SET Small end Threaded 小端带螺纹SF Semi-Finished 半光SG Sight Glass 视镜SH Surface Hard Facing 硬质密封面SK Sketch 草图SMAW Shielded Metal Arc Wel**** 有保护的金属电弧焊SMLS Seamless 无缝SN Swaged Nipple 异径短管SO Slip – On 滑套SOF Slip – On Flange 滑套法兰SPEC *Specification 规定，说明SPL Sound Pressure Lever 升压水准SQ *Square 方的，平方SR Shout Radius 短半径SRE Short Radius Elbow 短半径弯头SS *Stainless Steel 不锈钢ST Steam Trap 蒸汽疏水阀STD *Standard 标准STG Small Tongue & Groove 小椎槽面STL *Steel 钢STM Steam 蒸汽STM.TR Steam Tracing 蒸汽拌热SUCT Suction 吸入口SV Safety Valve 安全泄气阀SW Socket Weld 承插焊SWG Swage 锻造，模锻SWMG Swing Type 旋启式SYM Symmetrical 对称的TT Tee 三通TE Threaded End 螺纹端TEMP *Temperature 温度TG Tongue & Groove 椎槽THD *Threaded 螺纹的THK *Thickness 厚度TL Tangent Line 切线TN True North 真实北向TOC Top of Concrete 混凝土北向TOP Top of pipe 管顶TOS Top of Support 支架顶面Top of Steel 钢结构顶面TYP Typical 典型的UUB Union Bonnet 带活接头的阀盖UC Union Cap 带活接头的阀帽UN Union 活接头VV Valve 阀VAC Vacuum 真空VAR Variable 可变的VERT Vertical 垂直的VOL *Volume 卷，册，容量，体积WW *West 西WB Weld Branch 焊接支管WC Weld Cap 焊接管帽WD Width 宽度WE Weld End 焊接端WL Wel**** Line 焊接线WN Wel**** Neck 对焊法兰（颈部）WNF Weld Neck Flange 对焊法兰WP Working Pressure 工作压力W.P. Working Point 工作点WT Wall Thickness 壁厚Weight 重量XXH Extra Heavy 加强的，加厚的XXH Double Extra Heavy 双倍加强（厚）的XS Extra Strong 加强的XXS Double Extra Strong 双倍加强的YYP Yield Point 屈服点钢材的各种英文字母表示方法H Steel 宽缘工字钢Hadfield Manganese Steel 哈德菲尔德锰钢Hadfield Steel 哈德菲尔德高锰钢; 哈特非钢; 奥氏体高锰钢Hadifield Steel 高锰钢Half Spherical Steel Bobbin 半圆形钢质滚轮Half Steel 钢性生铁Half-Hard Steel 半硬钢Halvan Tool Steel 铬钒系工具钢Hammered Steel 锻钢Hand Drill Steel 手持式钢钎Hand Steel Snap 手用钢铆钉模Hard Alloy Steel 硬合金钢; 硬质合金钢Hard Steel 硬钢Hard-Drawn Steel Wire 硬拉钢丝Hardened And Tempered Steel 调质钢Hardened Steel 硬化钢; 淬火钢Hardened Steel Roller 淬火钢滚轮Hardened-Steel Bushing 淬火钢衬套Hardened-Steel Guideway 淬火钢导轨Hardened-Steel Tire 硬化钢环箍Hardening Of Steel 钢的硬化Harvey Steel 固体渗碳硬化钢Heat And Corrosion Resistant Steel 耐热防锈钢Heat Treatment Of Steel 钢的热处理Heat-Resistant Steel 耐热钢Heat-Resisting Alloy Steel 耐热合金钢Heat-Resisting Steel 耐热钢; 热强钢Heat-Treatable Steel 热处理钢Heat-Treated Steel 热处理钢Heat-Treated Steel Track 热处理钢履带Heavy Section Steel 大型型钢Heavy Steel Rolling Mill 大型轧钢厂Helical Steel Support 螺旋形井筒支架Hexagon Bar Steel 六角条钢Hexagonal Steel Bar 六角形钢筋Hi-Stren Steel 低合金高强度钢High Alloy Steel 高质合金钢High Angle Smooth Bottom Steel Bench Plane 高角平底钢刨High Boron Steel 高硼钢High Carbon Steel 高碳钢High Chrome Alloy Steel 高铬合金钢High Chrome Steel 高铬钢; 高铬钢High Chromium Steel 高铬钢High Frequency Steel Furnace 高频炼钢炉High Manganese Carbon Steel 高锰碳钢High Manganese Cast Steel 高锰铸钢High Manganese Stainless Steel 高锰不锈钢High Manganese Steel 高锰钢High Manganese Steel Casting 高锰钢铸件High Manganese Steel Frog 高锰钢辙叉High Manganese Steel Rail And Guard Rail 高锰钢辙叉及护轨High Nickel Steel 高镍钢; 高镍合金钢High Nickel-Chrome Steel 高镍铬钢High Pressure Stainless Steel Hose 高压不锈钢软管High Quality Steel 高级钢High Speed Steel Bit 高速钢钻头High Speed Steel Cutter 高速钢刀具High Speed Steel Ground Tap 高速钢磨削丝锥High Speed Steel Lathe Tool 高速钢车刀High Speed Steel Power Hacksaw Blade 高速钢机用锯条High Speed Steel Tool Bit 高速钢刀具High Speed Steel Turning Tool 高速钢车刀High Speed Steel Twist Drill 高速钢麻花钻High Speed Steel Wire 高速钢丝High Steel 高碳钢; 硬钢High Strength Alloy Steel Shackle 高强度合金钢锁扣High Strength Bevel Steel Washer 高强度钢斜垫圈High Strength Construction Steel 高强结构钢High Strength Hull Steel 高强度船体结构钢High Strength Low Alloy Steel 高强度低合金钢; 低合金高强度钢High Strength Plain Steel Washer 高强度平钢垫圈High Strength Steel 高强度钢材High Strength Steel Bar 高强钢筋High Strength Steel Plate 高强钢板High Strength Steel Washer 高强度钢垫圈High Strength Structural Steel 高强度结构钢High Tensile Deformed Steel Bar 高拉力异形钢筋High Tensile Reinforing Steel 高强钢筋High Tensile Steel 高强度钢; 高级钢High Tensile Steel Plate 高强钢板High Tensile Steel Tube 高强度钢管High Tensile Steel Wire 高强钢丝High Tensile Thin Steel Plate 高强薄钢板High Yield Stress Steel 高屈服强度钢High-Alloy Steel 高合金钢High-Alloy Steel Vessel 高合金钢容器High-Carbon Alloy Steel 高碳合金钢High-Carbon Chromium Steel 高碳铬钢High-Carbon High-Tensile Steel 高碳高张力钢High-Carbon High-Tensile Steel Wire 高碳高张力钢线High-Carbon Steel 高碳钢High-Carbon Steel Heat Treated 热处理过的高碳钢High-Chromium Stainless Steel 高铬不锈钢High-Creep Strength Steel 高蠕变强度钢High-Ductility Steel 高韧性钢; 高塑性钢High-Duty Steel 高强度钢High-Elastic Limit Steel 高弹性极限钢; 高弹性限度钢High-Frequency Electric Welded Steel Pipe 高频电焊钢管High-Frequency Transformer Silicon Steel Sheet 高频变压器硅钢片High-Grade Alloy Steel 高级合金钢High-Grade Alloy Structure Steel 高级合金结构; 高级合金结构钢High-Grade Carbon Steel 高级碳素钢High-Grade Steel 高级钢High-Quality Nickel Steel Tube 高级镍钢管High-Quality Steel 高质量钢; 优质钢High-Speed Steel 高速钢; 高速工具钢High-Speed Steel Bit 高速钢车刀High-Speed Steel Drill 高速钢钻头High-Speed Steel End Mill 高速钢端铣刀High-Speed Steel Geared Tap 高速钢磨牙丝锥High-Speed Steel Ingot 高速钢锭High-Speed Steel Lathe Tool 白钢车刀High-Speed Steel Tool 高速钢刀具High-Speed Tool Steel 高速工具钢; 高工钢High-Strength Bevel Steel Washer 高强度斜垫圈High-Strength Cast Steel 高速铸铁High-Strength Low Alloy Steel 高强低合金钢High-Strength Low-Allow Steel 高强度耐低温钢High-Strength Plain Steel Washer 高强度平垫圈High-Strength Quality Steel Wire 高强优质钢丝High-Strength Steel 高强度钢High-Strength Steel Electrode 高强度钢焊条High-Strength Steel Washer 高强度垫圈High-Sulfur Steel 高硫钢High-Temper Steel 高温回火钢High-Temperature Steel 耐高温钢High-Tensile Steel 高强度钢; 高强钢High-Tensile Steel Bar 高强度钢筋High-Tensile Steel Bars 高强度粗钢筋High-Tensile Steel Reinforcement Bar Fixture 高强钢筋夹具High-Tensile Steel Wires 高强度钢丝High-Tensile Structural Steel 高强度结构钢High-Vanadium Steel 高矾钢; 高钒钢High-Yield Strength Steel 高屈服点钢; 高屈服强度钢Highyield Low-Alloy Steel 高强度低合金钢Hoe Steel 中耕机锄铲Hole Steel Propeller 钢制空心螺旋桨Hollow Drill Steel 中空钻探钢Hollow Square Steel 空心方钢Hollow Steel 空心钢; 中空钢Hollow Steel Propeller 中空钢制螺旋桨Hollow Steel Rim 空心轮辋Hollow Steel Roller 空心钢辊Hollow Steel Section 薄壁型钢Hollow Steel Spoke Wheel 空心钢辐轮Hollow-Drill Steel 空心钻杆Homogeneous Steel 均质钢; 均质钢Homogeneous Steel Plate 均质钢板; 均质钢板Honda Steel 本多磁钢Hoop Steel 箍钢带Hot Die Steel 热锻模钢; 热作模具钢Hot Work Tool Steel 热镀模具钢; 热锻模具钢Hot-Die Steel 热变形模具钢; 高温模具钢Hot-Dip Galvanized Steel Wire 热镀锌钢丝Hot-Dipped Galvanized Sheet Steel 热浴镀锌薄板钢材Hot-Rolled Mild Steel 热轧软钢Hot-Rolled Sheet Steel 热轧钢板Hot-Rolled Sillcon Steel Sheet 热轧硅钢板Hot-Rolled Steel 热轧钢Hot-Rolled Steel Bar 热轧钢筋Hot-Rolled Steel Channel 热轧槽钢Hot-Rolled Steel Joist 热轧钢龙骨Hot-Rolled Steel Section 热轧型钢Hot-Working Die Steel 热锻模钢Hubbing Steel 冲模钢Hull Steel 船用钢; 造船钢Hy-Tuf Steel 海图夫低合金高强度钢Hydra Steel 海德拉热模具钢Hydraulic Steel Holder 液压持纤器Hydraulic Steel Support 液压钢支架Hynack Steel Plate 海纳克护膜耐蚀钢板Hypereutectoid Steel 过共析钢; 超共析钢Hypoeutectoid Steel 亚共析钢Hysteresis Steel 磁滞钢I-Section Steel Pile 工字型钢桩I-Steel 工字形钢; 窄边工字钢I-Steel Pile 工字型钢桩Inclusion In Steel 钢内夹杂Indented Steel Wire 齿纹钢丝Industrial Steel Window 工业厂房钢窗Ingot Steel 钢锭; 锭钢Inland Steel (美国) 内陆钢铁公司Instrument For Measuring Oxygen In Molten Steel 钢液定氧仪Integral (Drill) Steel 整体钢钎Integral Steel 整体钢钎Integrated Iron And Steel Works 综合性钢铁厂Intermediate Grade Steel 中级钢Internal Fixation With Steel Plate 钢板内固定术Invar Steel 殷钢Iron And Steel Base 钢铁基地Iron And Steel Casting 钢铁铸件Iron And Steel Company 钢铁公司Iron And Steel Industry 钢铁工业Iron And Steel Manufacture 钢铁制造Iron And Steel Material Shaped 钢铁型材Iron And Steel Plant 钢铁厂Iron And Steel Scrap 废钢铁Iron And Steel Sheet And Plate 钢铁板材Iron And Steel Sheet Piling 铁及钢板桩法凿井Iron And Steel Wire 钢铁丝材Iron And Steel Works 钢铁厂Iron-And-Steel Furnace 黑色金属冶金炉Irreversible Steel 不可逆钢Joist Steel 梁钢Joy Extensible Steel Band 乔伊可伸缩式钢带运输机Jumper Steel 钻杆钢; 长凿钢Jute-Covered Steel Pipe 包黄麻钢管Killed Carbon Steel (KCS) 镇静碳钢Killed Steel 镇静钢Killed Steel (去氧钢) 脱氧钢Krupp Austenite Steel 奥氏体铬镍合金钢Krupp Triple Steel 克鲁普铬钼钒高速钢L.P.N. Steel 低氮碱性底吹转炉钢Lacquer-Coated Steel Sheet 涂漆薄钢板Lead Bearing Steel 含铅钢Lead Treated Steel 含铅易切削钢Lead-Coated Steel Plate 镀铅钢板Lead-Sheathed Steel-Taped 铅包钢带Leaded Low-Phosphorus Steel 含铅低磷钢Lean Alloy Steel 低合金钢Ledloy Free Cutting Steel 加铅易切削钢Light Channed Steel 轻型槽钢Light Gauge Steel 轻量型钢Light Weight Steel Shape 轻型钢材Light-Gauge Steel Section 薄壁型钢Light-Weight Angle Steel 轻型角钢Lightgage Steel Joist 轻钢龙骨Lightweight Steel Construction 轻钢结构Lightweight Steel Shape 冷弯型钢Lip Hat Section Steel 带缘帽型钢Lip Z Steel 带缘Z型钢Liquid Steel 钢水Liquid-Compressed Steel 液态挤压钢; 加压凝固钢Little Bessemer Steel 小型酸性转炉钢Lock Bar Steel Pipe 箍锚钢管Locking Steel Wire 锁紧钢丝Long Steel Tape 钢卷尺Long Steel Wire Saw 长钢丝锯Long-Span Steel Framing 大跨钢构架Low Alloy Steel 低合金钢Low Alloy Steel High Side Wagon 低合金钢敞车Low Alloy Steel Plate 低合金钢板Low Alloy Tool Steel 低合金工具钢Low Alloyed Steel 低合金钢Low Carbon Steel 低碳钢Low Carbon Steel Electrode 低碳钢焊条Low Carbon Steel Pipe 低碳钢管Low Carbon Steel Welding Electrode 低碳钢电焊条Low Hysteresis Steel 低磁滞钢; 低磁滞硅钢Low Machinability Steel 难切削钢Low Manganess Steel 低锰钢Low Pressure Stainless Steel Hose 低压不锈钢软管Low Steel 低碳钢Low Steel Proportion 低含钢率Low Temperature Steel Electrode 低温钢焊条Low Tungsten High Speed Steel 低钨高速钢Low-Alloy High-Strength Steel 低合金高强度钢Low-Alloy High-Tensile Structural Steel 低合金高强度结构钢Low-Alloy Steel Covered Arc Welding Electrode 低合金钢焊条Low-Alloy Threading Steel 低合金螺纹钢Low-Alloy Tool Steel 低合金工具钢Low-Angle Smooth Bottom Steel Bench Plane 低角平底钢刨Low-Carbon Cast Steel 低碳铸钢Low-Carbon Steel 低碳钢Low-Chrome Steel 低铬钢Low-Ductility Steel 低塑性钢Low-Expansion Steel 低膨胀钢Low-Temperature (Low Temperature) Steel 低温钢Lowalloy Structural Steel 低合金钢Machine Steel 机件钢; 机器钢Machinery Steel 机器钢Magnaflux Steel 航空用高强度钢Magnet Steel 磁钢Magnetic Steel 磁钢; 磁性钢Magnetic Steel Detector 钢筋磁性检测仪Magnetically Soft Steel 软磁钢Main Reinforcing Steel 主钢筋Major-Orthotropic Steel-Plate Bridge 主正交各向异性钢板桥Malleable Mild Steel 韧性低碳钢; 韧性软钢Malleable Steel 展性钢; 软钢; 韧性钢Man-Ten Steel 低合金高强度钢Manganese Silicon Spring Steel 锰硅弹簧钢Manganese Silicon Steel 锰硅钢Manganese Silicon Tool Steel 锰硅工具钢Manganese Spring Steel 锰弹簧钢Manganese Steel 锰钢; 哈德菲尔德锰钢Manganese Tool Steel 锰工具钢Manganese Vanadium Steel 锰钒钢Manganese Vanadium Tool Steel 锰矾工具钢; 锰钒工具钢Manufacture Of Iron And Steel By Melting 钢铁熔炼Maraging Steel 马氏体时效钢Marconi Steel Tape Recorder 马可尼磁带录音机Martensite Steel 马登斯体钢; 马氏体钢Martensitic Stain Less Steel 马氏体不锈钢Martensitic Steel 马氏体钢Martensitic Steel 马氏永磁体Martin Steel 平炉钢; 马丁钢Martinel Steel 马蒂内尔结构钢; 硅锰钢; 硅锰结构钢Mattress Netting Steel Wire 钢丝床用钢丝Measuring Case Depth For Steel 钢表层硬化深度测定法; 钢的表层硬化深度测定法Mechanically Capped Steel 机械封顶钢Medium Alloy Steel 中合金钢Medium Carbon Steel 中碳钢Medium Hard Steel 中等硬度钢; 中硬钢; 在硬钢Medium Manganese Steel 中锰钢Medium Steel (MS) 中碳钢Medium Temper Steel 中等回火钢Medium Width Steel Strip 中等宽度带钢Medium-Hard Steel 中硬钢Merchant Steel 商品钢; 商品条钢; 条钢Mercury-In-Steel Thermometer 钢管水银温度计; 钢壳水银温度计Mild Carbon Steel 低碳钢Mild Carbon Steel Strip 低碳带钢Mild Sheet Steel 软钢板Mild Steel 软钢; 低碳钢Mild Steel Arc Welding Electrode 低碳钢焊条Mild Steel Channel 槽钢Mild Steel Checkered Plate 花纹钢板Mild Steel Equal Angle 等边角钢Mild Steel Expanded Sheets 钢板网Mild Steel Fire Box 软钢板火箱Mild Steel Hexagonal Bolts 六角螺丝梗Mild Steel Hexagonal Bolts And Nuts 六角螺丝闩Mild Steel I-Beam 低碳工字钢Mild Steel Ingot 低碳钢锭Mild Steel Plate 软钢板Mild Steel Reinforcement (含钢量0.12--0.25%) 软钢钢筋Mild Steel Shank 软钢手柄Mild Steel Sheet 软钢皮Mild Steel Welding Rod 低碳钢焊丝Mild Steel Wire 低碳钢丝Mild-Carbon Steel Strip 低碳带钢; 低碳钢带Mild-Steel Domestic Boiler 软钢家用锅炉Mild-Steel Sheet 低碳钢薄板Mini Steel Plant 小型钢铁厂Mishima Magnet Steel 铝镍强磁钢Mold Steel 型模钢Molten Steel 钢水; 钢液Molybdenum High Speed Steel 钼高速钢第31 页。
相机术语中英文对照表
62 standard white 63 false color 64 image recording quality 65 recording image quality 66 recording pixel count 67 image protection and erase 68 image recording format 69 recording media 70 cloudy 71 creative zone 72 processing 73 processing parameters 74 optical viewfinder 75 active AF point indicator 76 merge 77 frame
126 tab sheet 127 [Remove checkmark] button 128 autoflash system
129 noise reduction for long exposures 130 communication 131 TIFF format 132 TTL auto white balance 133 TTL 3 point AiAF (1 point measurement is possible) 134 apply 135 digital AF/AE SLR 136 digital signature 137 digital zoom 138 digital terminal 139 digital exposure compensation 140 digital exposure compensation amount
transmitting images to or from a CF card (while 141 connecting to a computer) 142 Design rule for Camera File system (sRGB143 cDoemsipglniarnutl)e for Camera File system, DPOF-compliant
管道英文缩写译文
管道英文缩写译文/wingman1985/archive/2008/12/10/1240055.htmlA Anchor 固定ABS *Absolute 绝对的AISI *American Iron andSteel Institute 美国钢铁学会ANSI *American NationalStandards Institute 美国国家标准学会API *American Petroleum Institute 美国石油学会APPROX *Approximate 大约，近似的ASB Asbestos 石棉ASME *American Society Of Testing Material 美国机械工程师协会ASSY *Assembly 装配，组装ASTM *American Society OfTesting Material 美国材料实验协会ATM *Atmosphere 大气压AWG *American Wire Gage 美国线规AWS *American Wel**** Society 美国焊接协会AWWA *American Water WorksAssociation 美国水工协会BBB Bolted Bonnet 栓柱连接的阀盖BB By Buyer 买方供货B-B Beveled End-Beveled End 两端为坡口端BC Bolt Circle 螺栓中心圆B.C Bolted Cover(cap) 螺栓连接的阀兰盖（帽）BE Beveled End (for wel****) 坡口（焊接用）B.E Bell End 承口BEP Both Ends Plain 两端平BET Both Ends Threaded 两端带螺纹BL Battery Limit 装置区边界BF Blind Flange 法兰盖BLD Blind 盲板BLDG *Buil**** 建筑物BM Bill Of Material 材料表BOP Bottom Of Pipe 管底B-P Beveled End —Plain End 坡口端.平端BV Butterfly valve 蝶阀BWG * Birmingham Wire Gage 伯明翰线规BW Butt Weld 对焊CC Cap 管帽C-C Center to Center 中至中C-E Center to End 中至端面C-F Center to Face 中至面CH-OP Chain Operated 链条操纵的CH.PL Checkered Plate 花纹钢管C.I *Cast Iron 铸铁CL *Class 英制压力等级，等级，种类CLEAR Clearance 间隙COD Continued on Drawing 接续图COL *Column 柱，塔CONC Concentric 同心的CONN Connection 连接，接口CONT *Continue 连续CONT.V. Control Valve 控制阀CPLG Coupling 管接头，连轴节C.R. Concentric Reducer 同心异径管C.S. *Carbon Steel 碳钢C.S. Cold Spring 冷紧C.S.C. Car Seal Close 在关闭状态下封住C.S.O. Car Seal Open 在开启状态下封住CUST Customer 客C.V Check Valve 止回阀DDEG *Degree 度DF Drain funnel 排液漏斗DIA *Diameter 直径DIM *Dimension 尺寸DISCH *Discharge 出口，排出Diaphragm VELVE 隔膜阀DMF Double Male And Female 双重凹凸DN *Double Male And Female 公称直径DN Down 下DR Drain 排液DS Directional Stop 定向限为架DWG *Drawing 图EE *East 东EC External Coating 外面涂防腐层ECC Eccentric 偏心EFW Electric Fusion Welded 电容焊的EL(ELEV) *Elevation 标高；立面ELL Elbow 弯头EQIOP Equipment 设备，装置EQUIV Equivalent 相当的E.R. Eccentric Reducer 偏心异经管ERW Electric Resistance Welded 电阻焊的EW Eye Washer & Shower 洗眼器及淋浴器EXP.JT Expansion Joint 膨胀节FFDN Foundation 基础FF Flat Faced Or Full Faced 全平面；满平面F-F Face To Face 面至面FGW Fusion Gas Wel**** 气熔焊FIG *Figure 图FL Floor 楼面FLEX TUBE Flexible Tube 挠性管FLG Flange 法兰FLGD Flanged 法兰式的FLGF Flanged Face 法兰面FOB Flat On Bottom 底面平FOT Flat On Top 顶面平FP Fix Point 固定点FS Forged Steel 锻钢FTF Fitting To Fitting 管件直连FTG Fitting 管件FURND Furnished 提供的，装设的FW Field Weld 现伤焊GG Guide 导向GA *Gage 表，表压，规（线规）GALV *Galvanize 镀锌GL Ground Level 地面GLV Globe Valve 截止阀GEAR OP Gear Operated 齿轮传动的GMAW Gas Metal Arc Wel**** 金属极惰气体保护焊GSKT Gasket 垫片GTAW (Inert)Gas Tungsten Arc Wel**** 惰性气体保护钨极电弧焊GV Gate Valve 闸阀HH Hanger 吊架HC Hose Connection 软管接头H.CPLG Half Coupling 半节管接头HDR Header 总管HEX *Hexagon 六角形HF Hard Alloy Face on阀内件（阀心）为Valve Trim 硬质合金密封面HH Hand Pole 手孔HOR Horizontal 水平的H.P *High Pressure 高压HS Hose Station 软管IID *Inside Diameter 内径IN *Inch 英寸INS Insulation 隔热INST Instrument 仪表INV Invert (inside bottom of pipe) 管子内底IPS Iron Pipe size 铁管尺寸ISO Isometric Drawing 周测图（空视图）I.S.B.L Inside Battery Limit 装置边界内恻ISNS Inside screw & Non-rising Stem 内螺纹非升杆ISRS Inside screw & Rising stem 内螺纹升杆JJT Joint 接头JS Jack Screw 顶开（起）螺栓LLC Locked Closed 在关闭状态下锁定LEP Large end plain 大端为平的LET Large end Threaded 大端带螺纹LG Long 长LGF Lens Gasket Face 透镜垫连接面L.H.THD Left Hand Thread 左螺纹LIFT Lift Type 升降式LJ Lap Joint 搭接LJF Lap Joint Flange 松套法兰LO Locked Open 在开启状态下锁定L.P. Low Pressure 低压LR Long Radius 长半径LRE Long Radius Elbow 长半径弯头LTG Large Tongue & Groove 大椎槽MMATL Material 材料MAX Maximum 最大MB Machine Bolt 机器螺栓（单头）MF Male and Female 凸和凹MFG Manufacture 制造MF *Manufacture 制造厂MH Manhole 人孔MI Malleable Iron 可锻铸铁MIN *Minimum 最小MJ Mechanical Joint 机械接头M.L Match Line 连续线MSS * Manufacturers Standardization Society of the Valve and Fittings Industry, Inc.美国阀门和管件制造商标准化协会MTO Material take-off 材料统计MW Minimum Wall 最小壁厚M.W. Mineral Wool 矿（物）棉NN *North 北NB Nominal Bore 公称孔径N.B. Non-Bonnet 无阀盖NC Normally Closed 常闭NIP Nipple 短管NO Normally Open; 常开*Number号；数量NO INS No Insulation 不隔热NOM Nominal 公称的；额定的NOZ Nozzle 管口NPS Nominal Pipe Size 公称管径NPSH Net Positive Suction Head 净正吸入压头NPT *American National Taper 美国锥管螺纹Pipe ThreadNS Nominal Size 公称直径NV Needle Valve 针形阀OOD *Outside Diameter 外径OET One end Threaded 一端带螺纹OR Outside Radius 外半径ORF Orifice 孔板ORIENT Orientation 方位OS & Y Outside Screw and Yoke 外螺纹阀杆和阀轭OSNB Outside Screw Non-Bonnet 外螺纹无阀盖PP Plug 堵头PAP Piping Arrangement Plan 管道布置平面图PB Pressure Seal Bonnet 压力密封的阀盖P-B Plain End –Bevel End 平端—坡口端PC Pressure Seal Cap 压力密封的阀帽P.C.D. Pitch Circle Diameter 节圆直径PE Plain End (not beveled) 平端（无坡口）PF Platform 平台PID Piping & Instrument Diagram管道及仪表流程图PN *Nominal Pressure 公称压力PN Plant North 工厂北向POS point of Support 支承点P-P Plain End—Plain End 两端为平端PREP Preparation 加工准备PSIA *Pounds Per Square InchAbsolute 磅/PSIG Pounds Per Square Inch Gage 磅/PT Point 点PTFE *Polytetrafluoroethylene 聚四氟乙烯PT.NO Part No. 件号PV Plug Valve 旋塞阀PVC *Poly Vinyl Chloride 聚氯乙烯QQTY *Quantity 数量RR *Radius 半径RED Reducer 异径管REF Reference 参考REINF Reinforce 加强REQD Required 需要；申请REV *Revision 修改RF Raised Face 凸面RG Ring Gasket 环形垫片R.H.THD Right Hand Thread 右螺旋RJ Ring Joint 环垫接头RO Restriction Orifice 限流孔板RPM *Revolutions Per Minute 转/分RPS *Revolutions Per Second 转/秒RS Resting Support 支承架，滑动架RTJ Ring Type Joint（见RJ）RV Relief Valve 安全泄液阀SS *South 南S Spring 弹簧（管架用）SAW (Automatic)Submerged Arc Wel**** 自动埋弧焊SB Stud Bolt 双头螺栓SB Screwed Bonnet 螺纹阀盖SC Sample Cooler 取样冷却器SCH *Schedule 管壁厚系列号SCRD Screwed 螺纹SEP Small end Plain 小端为平的SET Small end Threaded 小端带螺纹SF Semi-Finished 半光SG Sight Glass 视镜SH Surface Hard Facing 硬质密封面SK Sketch 草图SMAW Shielded Metal Arc Wel**** 有保护的金属电弧焊SMLS Seamless 无缝SN Swaged Nipple 异径短管SO Slip – On 滑套SOF Slip – On Flange 滑套法兰SPEC *Specification 规定，说明SPL Sound Pressure Lever 升压水准SQ *Square 方的，平方SR Shout Radius 短半径SRE Short Radius Elbow 短半径弯头SS *Stainless Steel 不锈钢ST Steam Trap 蒸汽疏水阀STD *Standard 标准STG Small Tongue & Groove 小椎槽面STL *Steel 钢STM Steam 蒸汽STM.TR Steam Tracing 蒸汽拌热SUCT Suction 吸入口SV Safety Valve 安全泄气阀SW Socket Weld 承插焊SWG Swage 锻造，模锻SWMG Swing Type 旋启式SYM Symmetrical 对称的TT Tee 三通TE Threaded End 螺纹端TEMP *Temperature 温度TG Tongue & Groove 椎槽THD *Threaded 螺纹的THK *Thickness 厚度TL Tangent Line 切线TN True North 真实北向TOC Top of Concrete 混凝土北向TOP Top of pipe 管顶TOS Top of Support 支架顶面Top of Steel 钢结构顶面TYP Typical 典型的UUB Union Bonnet 带活接头的阀盖UC Union Cap 带活接头的阀帽UN Union 活接头VV Valve 阀VAC Vacuum 真空VAR Variable 可变的VERT Vertical 垂直的VOL *Volume 卷，册，容量，体积WW *West 西WB Weld Branch 焊接支管WC Weld Cap 焊接管帽WD Width 宽度WE Weld End 焊接端绝对标高 absolute elevation海平面标高 over-sea mean level (OSL)标高，立面 elevation (EL)混凝土顶面 top of concrete架顶面 top of support (TOS)钢结构顶面 top of steel梁项面 top of beam (TOB)支撑点 point of support (POS)管顶 top of pipe (TOP)管底 bottom of pipe (BOP)沟底 bottom of trench管子内底 invert (inside bottom of pipe)底平 flat on bottom (FOB)顶平 flat on top (FOT)工作点 working point (W.P.)面至面 face to face (F-F)中心至端面 center to end (C-E)中心至面 center to face (C-F)中心至中心.中至中 center to center (C-C)坐标 coordinate坐标原点 origin of coordinate出口中心线 center line of discharge入口中心线 center line of suction中心线 centerline (CL)入口 inlet, suction出口 outlet, discharge排出口 exhaust距离 distance另外常用的还有：COP－管道中心标高TOP－管道顶标高TOB－支撑管道的管架顶标高（一般用于同一管架上的一排管道）所有管道标高均与其是否保温，保温厚度等无关，指的均是管道本身。
特瑞堡中文泛塞密封
2
特康® 泛塞®
■ 概述
特康® 泛塞® 是一种单作用，弹簧施力的密封件，用于 动态和静态运动。
泛塞® 在广泛的应用中是十分有效的。适用于要求具有 较好的耐化学介质的性能时，或者要求密封件工作在 极端温度下，以及用于需要良好的挤压和压缩性能的 场合。
最新资料请访问 2008年5月版
1
特康® 泛塞®
■ 选择正确的密封件
特康® 泛塞® 在所有工业领域的诸如液压缸和气缸之类 的元件设计中提供非常重要的作用，包括: - 极好的密封性能 - 非常耐磨损 - 抗间隙挤出性好 - 良好的耐腐蚀和耐磨性能 - 非常好的温度性能 - 摩擦系数小 - 结构紧凑 - 安装简单 特康® 泛塞® 有各种几何形状和结构，允许针对每种用 途选择最佳的形状。它们能够由各种特康® 材料（我们 的专利PTFE基复合物）制成，这些复合物是专门针对 密封件的配方，并且提供上乘的特性，专门满足我们 客户的要求。 当需要时，也能够用佐康® 材料（我们的专利聚乙烯基 复合物）制成。 为了针对您的用途，选择最好的特康® 泛塞® ，您必须 首先确定功能参数，第4页的表I和表II，以及第5页的 表III则能够用来对密封件和材料进行初选。这些表中详 细给出了在样本的何处能够找到进一步的细节。 考虑配合面的质量也是重要的，它对密封系统的使用 寿命和功能有重大的影响，有关这方面的指南在13页 和14页给出。 如果就有关密封件的技术规格需要帮助，请联系特瑞 堡密封系统公司，可以找您当地的市场部门，或登陆
下面列出泛塞在高达15ms49英尺s的速度下能够密封能够承受200mpa2000bar29000psi以上的高压能够安装在符合milg5514f和din3771的沟槽中弹簧力系统压力varisealvariseal选择表动态mpabapsi静态mpabapsim215454506527606008702709426050015m2s1645450652760600870270942605001005t40202002900606008702709423044615404005801808001160312018426050001t05hf28404005801808001160320032826050001t05roto2815150217525250362510014826050010c满足表ii外套材料选择指南turcont05turcont24turcont24turcont40turcont40turcont01zurconz80turcont78turcont01turcont01最新资料请访问wwwtsstrelleborgcom2008年5月版密封件接触的介质或工作条件静态或稍微动态往复旋转技术数据用途材料型式页码最高压力用途的类型工作温度最高速度标准材料空气气体水蒸气油原油普通化学品石油化学品食品药品真空材料选择指南t012500mm2500mm2500mm2500mm2500mm2500mm2500mm2500mm特殊材料适合较高的辐射负载有关这方面的进一步详细资料请联系特瑞堡密封系统公司
管件的各种英文缩写
管件的各种英文缩写管道英文缩写A Anchor 固定ABS *Absolute 绝对的AISI *American Iron andSteel Institute 美国钢铁学会ANSI *American NationalStandards Institute 美国国家标准学会API *American Petroleum Institute 美国石油学会APPROX *Approximate 大约，近似的ASB Asbestos 石棉ASME *American Society Of Mechanical Engineers美国机械工程师协会ASSY *Assembly 装配，组装ASTM *American Society OfTesting Material 美国材料实验协会ATM *Atmosphere 大气压AWG *American Wire Gage 美国线规AWS *American Wel**** Society 美国焊接协会AWWA *American Water WorksAssociation 美国水工协会BBB Bolted Bonnet 栓柱连接的阀盖BB By Buyer 买方供货B-B Beveled End-Beveled End 两端为坡口端BC Bolt Circle 螺栓中心圆B.C Bolted Cover(cap) 螺栓连接的阀兰盖（帽）BE Beveled End (for wel****) 坡口（焊接用）B.E Bell End 承口BEP Both Ends Plain 两端平BET Both Ends Threaded 两端带螺纹BL Battery Limit 装置区边界BF Blind Flange 盲板法兰BLD Blind 盲板BLDG *Buil**** 建筑物BM Bill Of Material 材料表BOP Bottom Of Pipe 管底B-P Beveled End —Plain End 坡口端.平端BV Butterfly valve 蝶阀BWG * Birmingham Wire Gage 伯明翰线规BW Butt Weld 对焊CC Cap 管帽C-C Center to Center 中至中C-E Center to End 中至端面C-F Center to Face 中至面CH-OP Chain Operated 链条操纵的CH.PL Checkered Plate 花纹钢管C.I *Cast Iron 铸铁CL *Class 英制压力等级，等级，种类CLEAR Clearance 间隙COD Continued on Drawing 接续图COL *Column 柱，塔CONC Concentric 同心的CONN Connection 连接，接口CONT *Continue 连续CONT.V. Control Valve 控制阀CPLG Coupling 管接头，连轴节C.R. Concentric Reducer 同心异径管C.S. *Carbon Steel 碳钢C.S. Cold Spring 冷紧C.S.C. Car Seal Close 在关闭状态下封住C.S.O. Car Seal Open 在开启状态下封住CUST Customer 客C.V Check Valve 止回阀DDEG *Degree 度DF Drain funnel 排液漏斗DIA *Diameter 直径DIM *Dimension 尺寸DISCH *Discharge 出口，排出Diaphragm VELVE 隔膜阀DMF Double Male And Female 双重凹凸DN Norminal Diameter公称直径DN Down 下DR Drain 排液DS Directional Stop 定向限为架DWG *Drawing 图EE *East 东EC External Coating 外面涂防腐层ECC Eccentric 偏心EFW Electric Fusion Welded 电容焊的EL(ELEV) *Elevation 标高；立面ELL Elbow 弯头EQIOP Equipment 设备，装置EQUIV Equivalent 相当的E.R. Eccentric Reducer 偏心异经管ERW Electric Resistance Welded 电阻焊的EW Eye Washer & Shower 洗眼器及淋浴器EXP.JT Expansion Joint 膨胀节FFDN Foundation 基础FF Flat Faced Or Full Faced 全平面；满平面F-F Face To Face 面至面FGW Fusion Gas Wel**** 气熔焊FIG *Figure 图FL Floor 楼面FLEX TUBE Flexible Tube 挠性管FLG Flange 法兰FLGD Flanged 法兰式的FLGF Flanged Face 法兰面FOB Flat On Bottom 底面平FOT Flat On Top 顶面平FP Fix Point 固定点FS Forged Steel 锻钢FTF Fitting To Fitting 管件直连FTG Fitting 管件FURND Furnished 提供的，装设的FW Field Weld 现伤焊GG Guide 导向GA *Gage 表，表压，规（线规）GALV *Galvanize 镀锌GL Ground Level 地面GLV Globe Valve 截止阀GEAR OP Gear Operated 齿轮传动的GMAW Gas Metal Arc Wel**** 金属极惰气体保护焊GSKT Gasket 垫片GTAW (Inert)Gas Tungsten Arc Wel**** 惰性气体保护钨极电弧焊GV Gate Valve 闸阀HH Hanger 吊架HC Hose Connection 软管接头H.CPLG Half Coupling 半节管接头HDR Header 总管HEX *Hexagon 六角形HF Hard Alloy Face on阀内件（阀心）为Valve Trim 硬质合金密封面HH Hand Hole 手孔HOR Horizontal 水平的H.P *High Pressure 高压HS Hose Station 软管IID *Inside Diameter 内径IN *Inch 英寸INS Insulation 隔热INST Instrument 仪表INV Invert (inside bottom of pipe) 管子内底IPS Iron Pipe size 铁管尺寸ISO Isometric Drawing 周测图（空视图）I.S.B.L Inside Battery Limit 装置边界内恻ISNS Inside screw & Non-rising Stem 内螺纹非升杆ISRS Inside screw & Rising stem 内螺纹升杆JJT Joint 接头JS Jack Screw 顶开（起）螺栓LLC Locked Closed 在关闭状态下锁定LEP Large end plain 大端为平的LET Large end Threaded 大端带螺纹LG Long 长LGF Lens Gasket Face 透镜垫连接面L.H.THD Left Hand Thread 左螺纹LIFT Lift Type 升降式LJ Lap Joint 搭接LJF Lap Joint Flange 松套法兰LO Locked Open 在开启状态下锁定L.P. Low Pressure 低压LR Long Radius 长半径LRE Long Radius Elbow 长半径弯头LTG Large Tongue & Groove 大椎槽MMATL Material 材料MAX Maximum 最大MB Machine Bolt 机器螺栓（单头）MF Male and Female 凸和凹MFG Manufacture 制造MF *Manufacture 制造厂MH Manhole 人孔MI Malleable Iron 可锻铸铁MIN *Minimum 最小MJ Mechanical Joint 机械接头M.L Match Line 连续线MSS * Manufacturers Standardization Society of the Valve and Fittings Industry, Inc.美国阀门和管件制造商标准化协会MTO Material take-off 材料统计MW Minimum Wall 最小壁厚M.W. Mineral Wool 矿（物）棉NN *North 北NB Nominal Bore 公称孔径N.B. Non-Bonnet 无阀盖NC Normally Closed 常闭NIP Nipple 短管NO Normally Open; 常开*Number号；数量NO INS No Insulation 不隔热NOM Nominal 公称的；额定的NOZ Nozzle 管口NPS Nominal Pipe Size 公称管径NPSH Net Positive Suction Head 净正吸入压头NPT *American National Taper 美国锥管螺纹Pipe ThreadNS Nominal Size 公称直径NV Needle Valve 针形阀OOD *Outside Diameter 外径OET One end Threaded 一端带螺纹OR Outside Radius 外半径ORF Orifice 孔板ORIENT Orientation 方位OS & Y Outside Screw and Yoke 外螺纹阀杆和阀轭OSNB Outside Screw Non-Bonnet 外螺纹无阀盖PP Plug 堵头PAP Piping Arrangement Plan 管道布置平面图PB Pressure Seal Bonnet 压力密封的阀盖P-B Plain End –Bevel End 平端—坡口端PC Pressure Seal Cap 压力密封的阀帽P.C.D. Pitch Circle Diameter 节圆直径PE Plain End (not beveled) 平端（无坡口）PF Platform 平台PID Piping & Instrument Diagram管道及仪表流程图PN *Nominal Pressure 公称压力PN Plant North 工厂北向POS point of Support 支承点P-P Plain End—Plain End 两端为平端PREP Preparation 加工准备PSIA *Pounds Per Square InchAbsolute 磅/PSIG Pounds Per Square Inch Gage 磅/PT Point 点PTFE *Polytetrafluoroethylene 聚四氟乙烯PT.NO Part No. 件号PV Plug Valve 旋塞阀PVC *Poly Vinyl Chloride 聚氯乙烯QQTY *Quantity 数量RR *Radius 半径RED Reducer 异径管REF Reference 参考REINF Reinforce 加强REQD Required 需要；申请REV *Revision 修改RF Raised Face 凸面RG Ring Gasket 环形垫片R.H.THD Right Hand Thread 右螺旋RJ Ring Joint 环垫接头RO Restriction Orifice 限流孔板RPM *Revolutions Per Minute 转/分RPS *Revolutions Per Second 转/秒RS Resting Support 支承架，滑动架RTJ Ring Type Joint（见RJ）RV Relief Valve 安全泄液阀SS *South 南S Spring 弹簧（管架用）SAW (Automatic)Submerged Arc Wel**** 自动埋弧焊SB Stud Bolt 双头螺栓SB Screwed Bonnet 螺纹阀盖SC Sample Cooler 取样冷却器SCH *Schedule 管壁厚系列号SCRD Screwed 螺纹SEP Small end Plain 小端为平的SET Small end Threaded 小端带螺纹SF Semi-Finished 半光SG Sight Glass 视镜SH Surface Hard Facing 硬质密封面SK Sketch 草图SMAW Shielded Metal Arc Wel**** 有保护的金属电弧焊SMLS Seamless 无缝SN Swaged Nipple 异径短管SO Slip – On 滑套SOF Slip – On Flange 滑套法兰SPEC *Specification 规定，说明SPL Sound Pressure Lever 升压水准SQ *Square 方的，平方SR Shout Radius 短半径SRE Short Radius Elbow 短半径弯头SS *Stainless Steel 不锈钢ST Steam Trap 蒸汽疏水阀STD *Standard 标准STG Small Tongue & Groove 小椎槽面STL *Steel 钢STM Steam 蒸汽STM.TR Steam Tracing 蒸汽拌热SUCT Suction 吸入口SV Safety Valve 安全泄气阀SW Socket Weld 承插焊SWG Swage 锻造，模锻SWMG Swing Type 旋启式SYM Symmetrical 对称的TT Tee 三通TE Threaded End 螺纹端TEMP *Temperature 温度TG Tongue & Groove 椎槽THD *Threaded 螺纹的THK *Thickness 厚度TL Tangent Line 切线TN True North 真实北向TOC Top of Concrete 混凝土北向TOP Top of pipe 管顶TOS Top of Support 支架顶面Top of Steel 钢结构顶面TYP Typical 典型的UUB Union Bonnet 带活接头的阀盖UC Union Cap 带活接头的阀帽UN Union 活接头VV Valve 阀VAC Vacuum 真空VAR Variable 可变的VERT Vertical 垂直的VOL *Volume 卷，册，容量，体积WW *West 西WB Weld Branch 焊接支管WC Weld Cap 焊接管帽WD Width 宽度WE Weld End 焊接端WL Wel**** Line 焊接线WN Wel**** Neck 对焊法兰（颈部）WNF Weld Neck Flange 对焊法兰WP Working Pressure 工作压力W.P. Working Point 工作点WT Wall Thickness 壁厚Weight 重量XXH Extra Heavy 加强的，加厚的XXH Double Extra Heavy 双倍加强（厚）的XS Extra Strong 加强的XXS Double Extra Strong 双倍加强的YYP Yield Point 屈服点。
CENTERLINE 2100 水平操作手柄电机控制中心（MCC）单元安装说明书
Installation InstructionsCENTERLINE 2100 Motor Control Center (MCC) Units with Horizontal Operating HandlesCatalog Number 2100About This Publication Use these instructions to install CENTERLINE® 2100 MCC units withhorizontal operating handles.For more information on the CENTERLINE 2100 Motor Control Center(MCC), refer to the CENTERLINE 2100 Low Voltage Motor Control CentersInstruction Manual, publication 2100-IN012.T o install units with vertical operating handles, refer to the CENTERLINE 2100Motor Control Center (MCC) Units with Vertical Operating HandlesInstallation Instructions, publication 2100-IN014.Topic Page About This Publication 1Important User Information 2Before You Begin 3Recommended Tools 5Ground the Unit 5Install the Unit Support Pan 5Install Swing-out Latch Brackets 8Install the Unit 8Install the Door 10More Resources 13ATTENTION: All covers and doors must be in place before you apply power tothe MCC. If units are removed, they must be replaced with the appropriate itemssuch as units, doors, and unit support pans. If the unit is not replaced, the arcresistant rating does not apply.2Rockwell Automation Publication 2100-IN060E-EN-P - February 2015CENTERLINE 2100 Motor Control Center (MCC) Units with Horizontal Operating HandlesImportant User InformationRead this document and the documents listed in the additional resources section about installation, configuration, and operation of this equipment before you install, configure, operate, or maintain this product. Users are required tofamiliarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws, and standards.Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required to be carried out by suitably trained personnel in accordance with applicable code of practice.If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the use or application of this equipment.The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or liability for actual use based on the examples and diagrams.No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or software described in this manual.Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation, Inc., is prohibited.Throughout this manual, when necessary, we use notes to make you aware of safety considerations.Labels may also be on or inside the equipment to provide specific precautions.WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous environment,which may lead to personal injury or death, property damage, or economic loss.ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property damage, or economic loss. Attentions help you identify a hazard, avoid a hazard, and recognize the consequence.IMPORTANTIdentifies information that is critical for successful application and understanding of the product.SHOCK HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that dangerousvoltage may be present.BURN HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that surfaces mayreach dangerous temperatures.ARC FLASH HAZARD: Labels may be on or inside the equipment, for example, a motor control center, to alert people topotential Arc Flash. Arc Flash will cause severe injury or death. Wear proper Personal Protective Equipment (PPE). Follow ALLRegulatory requirements for safe work practices and for Personal Protective Equipment (PPE).CENTERLINE 2100 Motor Control Center (MCC) Units with Horizontal Operating HandlesBefore You Begin Follow this procedure before you begin installing your unit.1.Remove all packaging material from the unit.2.Read the unit installation instructions.3.Manually exercise all switches, control auxiliary switches, circuit breakers,their respective operators, unit interlocks, trip mechanisms (test bypushing the ‘Push to T rip’ button), and any other operating mechanisms toverify proper operation.IMPORTANT Plug-in units with horizontal operating handles cannot be used in sectionswith series letters A...D. In sections with series letters E...J, these units can beplugged into only the top 5.5 space factors. There is no vertical bus in thebottom 0.5 space factor.IMPORTANT Sections with series letters E…J require retrofit kit, catalog number 2100H-R1,for 0.5 space factor, or catalog number 2100H-R2 for 1.0 or larger space factor.See CENTERLINE 2100 Motor Control Centers Retrofitting Units with HorizontalOperating Handles into Series E…J Sections, publication 2100-IN065, for moreinformation.ATTENTION: When you install units for CENTERLINE 2100 Motor Control Centers(MCC) with ArcShield™ baffles, you must make sure that you are installing a unitthat has the same arc resistance rating as the MCC in which it is being installed.Units that are not rated for 100 ms arc duration must not be installed in asection that is rated for 100 ms arc duration. If the incorrect unit is installed, thearc resistant rating does not apply. The 0.5 space factor units and doors are notavailable in ArcShield units with 100 ms arc duration designs. Do not use 0.5space factor units in 100 ms arc duration rated MCC sections.Rockwell Automation Publication 2100-IN060E-EN-P - February 201534Rockwell Automation Publication 2100-IN060E-EN-P - February 2015CENTERLINE 2100 Motor Control Center (MCC) Units with Horizontal Operating Handles Unit Support Pan Bushing Unit Support Pan Plastic Retaining Rivet Unit Latch/Interlock Pilot Devices Control Circuit Fuse Bloc and Fuses Control Terminal Block Handle Mechanism Circuit Breaker (shown) or Fusible Disconnect Control Circuit Transformer Unit Stab Assembly Overload Relay Contactor or Starter Starter Unit Nameplate Unit DoorRockwell Automation Publication 2100-IN060E-EN-P - February 20155CENTERLINE 2100 Motor Control Center (MCC) Units with Horizontal Operating HandlesRecommended Tools W e recommend having a screwdriver available for installation.Y ou need a 5/16 in. and a 3/8 in. socket wrench for installing ArcShield units.Ground the Unit Follow this procedure to ground the unit.1.Determine the minimum size grounding-conductor required from the following table.2.T o ground the unit to the structure ground bus, attach a unit grounding conductor between the unit chassis and the structure ground bus.The size of the grounding connector is based on the unit current rating.Install the Unit Support PanFollow this procedure to install the support pan.ATTENTION: If this unit is installed in a series E…J section without a verticalplug-in ground bus, it is necessary to either install a vertical plug-in ground buskit, catalog number 2100H-GS1, 2100H-79U, or 2100H-79UT, or ground the unitto the structure ground bus.Follow NFPA 70E safety guidelines when working on energized equipment.To avoid personal injury and damage to the unit, be certain that the unitoperating handle is in the OFF/O position before proceeding.Grounding Connector (minimum size #AWG)Current Ratings (A)Horsepower Rated Units (NEMA Size)100…601, 2861 (10036)101 (20044)201 (3005)3301…400-IMPORTANT The unit support pans above (or wireway pan for the topmost units in asection) and below the unit compartment must be in place before installingthe unit.ATTENTION: All covers and doors must be in place before you apply power tothe MCC. If units are removed, they must be replaced with the appropriate itemssuch as units, doors, and unit support pans.ATTENTION: If power sources are connected to the motor control center, useextreme caution when you insert units. All buses and the line sides of theinserted units are energized, and contact with these parts can cause injury anddeath.Follow NFPA 70E safety guidelines when working on energized equipment.6Rockwell Automation Publication 2100-IN060E-EN-P - February 2015CENTERLINE 2100 Motor Control Center (MCC) Units with Horizontal Operating Handles1.For ArcShield sections with 100 ms arc duration rating, remove the vertical wireway baffle and set aside for installation later.2.If present, remove the isolation barrier from the vertical-wireway wall cutout.3.De-energize the unit in the space below where the unit support pan is to be installed.4.Open the unit door above and below where the unit support pan is to be installed.5.Place the unit support pan into the unit space, hold the right side of the support pan approximately 4 in. (102 mm) higher than the left side.6.Place the left front corner of the support pan into the slot on the front of the left sidesheet flange.7.Place the left rear corner of the support pan into the slot of the left sidesheet C-channel.8.Lower the right edge of the unit support pan into the vertical-wireway wall cutout, and press down firmly.Rockwell Automation Publication 2100-IN060E-EN-P - February 20157CENTERLINE 2100 Motor Control Center (MCC) Units with Horizontal Operating Handles9.Secure the support pan.See the table for more instructions.Non-ArcShield Unit Support Pan InstallationArcShield Unit Support Pan Installation10.Replace the isolation barrier if one was removed.ForFollow This Step Non-ArcShield units Insert the white plastic retaining-clip through the holes in the vertical wirewaywall and pan. Work from inside the vertical wireway as shown. See Non-ArcShield Unit Support Pan Installation .All ArcShield units Secure the unit support pan to the right unit support with the ¼-20self-tapping screw that is supplied with the bracket. Tighten to 55 lb•in (6 N•m)with a 3/8 in. socket wrench. See ArcShield Unit Support Pan Installation.ArcShield units with 100ms arc duration ratingSecure the left-rear corner of the unit support pan with a 10-32 self-tappingscrew and tighten to 32lb•in. (3.6 N•m) by using a 5/16 in. socket wrench.PlasticRetaining ClipUnit Support PanUnit Support PanScrew Arc ResistantLatchBracketArc Resistant Latch Bracket ScrewUnit Support Pan8Rockwell Automation Publication 2100-IN060E-EN-P - February 2015CENTERLINE 2100 Motor Control Center (MCC) Units with Horizontal Operating HandlesInstall Swing-out Latch Brackets Swing-out latch brackets are used on all latch positions for all units withhorizontal handles.1.W ork from the inside of the vertical wireway cutout and place the swing-out latch bracket on the back of the front flange of the right unitsupport.2.Align the latch bracket with the slot in the right unit support so that the alignment tab of the bracket is resting on the bottom of the slot.3.W ork from the inside of the vertical wireway and tighten the two 10-32 self-tapping screws to 32 lb •in (3.6 N •m) to secure the swing-out latch bracket to the right unit support.Install the Unit Follow this procedure to install the unit.1.Remove the protective caps from the stab openings or open the manual shutters if present (automatic shutters open as the units are inserted).Vertical WirewayVertical Wireway CutoutRight Unit SupportSwing-out Latch ATTENTION: De-energize all units before installing or removing.When you install or remove MCC units, when possible, de-energize, lockout,and tag-out all sources of power to the MCC. If the MCC units are installed orremoved with power applied to the main power bus, follow establishedelectrical safety work practices. See the NFPA 70E Standard for Electrical Safetyin the Workplace publication.Review your company safety lockout and tag-out procedure.If power sources are connected to the motor control center, use extreme cautionwhen you insert units. All buses and the line sides of the inserted units areenergized, and contact with these parts can cause injury or death.All covers and doors must be in place before you apply power to the MCC. Ifunits are removed, they must be replaced with the appropriate items such asunits, doors, and unit support pans.ATTENTION: Plug-in MCC units can be heavy or awkward to handle. Use anassistant or a platform lift device if necessary to help you handle the unit.Rockwell Automation Publication 2100-IN060E-EN-P - February 20159CENTERLINE 2100 Motor Control Center (MCC) Units with Horizontal Operating HandlesReposition your hands as necessary to properly support the unit while you are installing the unit into the MCC.2.Place the unit on the bottom unit-support pan, slide the unit interlock to the left, and push the unit into the section until it is in the desired position,then release the unit interlock.3.Install other cables or devices.Bushing Slot Unit Support Pan Right Unit GuideLeft Unit GuideDisconnected PositionNormal Operating PositionUnit devices have been omitted for clarity.IMPORTANT There are two positions available (normal operating and disconnected). In thenormal operating position, the power and ground stabs are connected to theirrespective busses. In the disconnected position, the unit is partially removedfrom the MCC and the intermediate slot in the interlock plate is in line with thebushing located in the unit support pan. When the unit is locked in thisposition, the unit power and ground stabs are disengaged. This position can beused to prevent insertion of a unit into the MCC.ATTENTION: For proper operation of the latch/interlock mechanism, a style 3unit-support pan with bushing must be used below the unit. If the unit supportpan with bushing is not used, the unit could be removed under load, which can result in injury or death.TIP For the CENTERLINE 2100 MCC units with swing-out door latches, it isnecessary to rotate the movable portion of the latch bracket to a vertical orientation to avoid interference when installing the unit.IMPORTANTBe sure to comply with the National Electric Code 6.7 ft (2 m) unit handle-to-floor height limitation, as identified in NEC 2005 Article 404.8(A) and ULstandard 845, for units in the topmost location of a vertical section.A unit operating-handle extender kit, catalog number 2100H-NE1, is available for any handles higher than 6.7 ft (2 m) off the ground.10Rockwell Automation Publication 2100-IN060E-EN-P - February 2015CENTERLINE 2100 Motor Control Center (MCC) Units with Horizontal Operating Handles 4.For ArcShield sections with 100 ms arc duration rating, replace the vertical wireway baffle.Install the DoorFollow these procedures to install the door.1.Position the door over the unit opening while holding the right side of the door slightly toward you and push in the left side until it is flush with thefront of the structure.Rockwell Automation Publication 2100-IN060E-EN-P - February 201511CENTERLINE 2100 Motor Control Center (MCC) Units with Horizontal Operating Handles2.Swing the door open and slide each hinge pin through the door and structure hinges.3.If a control station is present, place it in the door cutout and tighten thecaptive screws.For Units With Follow This StepA control station Slide the hinge pin through the tab on the control station wiring first, then into the closest hinge.ArcShield with 100ms arc duration ratingTwo hinges are required for each hinge leaf.1.The upper hinge on each door must be removed from the structure to install/remove the uppermost hinge pin.2.Insert the hinge pin through the upper hinge, then through the hinge leaf and lower hinge.3.Install the upper hinge on the MCC structure with the ¼-20 self-tapping screw that is provided and tighten to 55 lb•in (6N•m) with a 3/8 in. socket wrench.Only top hinge must be removed to install hinge pin.Hinge Hinge Pin Hinge LeafHinge for Standard Units and ArcShield Units with Device Limited RatingHinge for ArcShield Units with 100 ms Arc Duration RatingCENTERLINE 2100 Motor Control Center (MCC) Units with Horizontal Operating Handles4.Rotate the movable portion of the swing-out latch bracket in the counter-clockwise direction unit it stops, close the door, and secure the latch.See CENTERLINE 2100 Low Voltage Motor Control CentersInstruction Manual, publication 2100-IN012, for more information onproper door latch orientations.For Follow This StepNon-arc resistant latches Turn each door latch ¼ turn until it catches on the unit support pan orstructure and holds the door closed.Units that are equipped witharc-resistant door latchesOrient the slot of the latch so that it is horizontal, then push in the latch androtate ¼ turn.TIPLatches can require a flat-head screwdriver to open and close.IMPORTANT If this unit is installed in a series E...J section, it is necessary to install a longerlatch assembly to latch into the wireway opening. The latch is included in theplug-in unit retrofit kit, catalog number 2100H-R1, or 2100H-R2.Arc Resistant LatchLatchTIP When properly latched, the slots on the arc resistant latches are vertical andthe latch springs are compressed. The spacing of the spring coils isdecreased.UncompressedSpring, UnlatchedCompressedSpring,Latched12Rockwell Automation Publication 2100-IN060E-EN-P - February 2015Rockwell Automation Publication 2100-IN060E-EN-P - February 201513CENTERLINE 2100 Motor Control Center (MCC) Units with Horizontal Operating HandlesMore ResourcesThese documents contain more information about related products from Rockwell Automation.Y ou can view or download publications at/literature/. T o order paper copies of technical documentation, contact your local Allen-Bradley® distributor or Rockwell Automation sales representative.ResourceDescriptionCENTERLINE 2100 Low Voltage Motor Control Centers Instruction Manual, publication 2100-IN012 Provides general instructions for MCC Units.CENTERLINE 2100 Motor Control Center Units with Vertical Operating Handles, publication 2100-IN014Provides information on the installation of units with vertical operating handles.Safety Guidelines for the Application, Installation, and Maintenance of Solid- state Control Installation Instructions, publication SGI-1.1Provides safety guidelines for the application, installation, and maintenance of solid-state control.Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1Provides general guidelines for installing a Rockwell Automation® industrial system.Product Certifications website, /products/certificationProvides declarations of conformity, certificates, and other certification details.Allen-Bradley, Rockwell Software, Rockwell Automation, CENTERLINE, and ArcShield are trademarks of Rockwell Automation, Inc.Trademarks not belonging to Rockwell Automation are property of their respective companies.Publication 2100-IN060E-EN-P - February 2015Supersedes Publication 2100-IN060D-EN-P - March 2014Copyright © 2015 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.Rockwell Automation SupportRockwell Automation provides technical information on the Web to assist you in using its products.At /support you can find technical and application notes, sample code, and links to software service packs. Y ou can also visit our Support Center at https:/// for software updates, support chats and forums, technical information, FAQs, and to sign up for product notification updates.In addition, we offer multiple support programs for installation, configuration, and troubleshooting. For more information, contact your local distributor or Rockwell Automation representative, or visit /services/online-phone .Installation AssistanceIf you experience a problem within the first 24 hours of installation, review the information that is contained in this manual. You can contact Customer Support for initial help in getting your product up and running.New Product Satisfaction ReturnRockwell Automation tests all of its products to help ensure that they are fully operational when shipped from the manufacturing facility. However, if your product is not functioning and needs to be returned, follow these procedures.Documentation FeedbackY our comments will help us serve your documentation needs better. If you have any suggestions on how to improve this document, complete this form, publication RA-DU002, available at /literature/.United States or Canada 1.440.646.3434Outside United States or CanadaUse the Worldwide Locator at /rockwellautomation/support/overview.page , or contact your local Rockwell Automation representative.United States Contact your distributor. You must provide a Customer Support case number (call the phone number above to obtain one) to your distributor to complete the return process.Outside United StatesPlease contact your local Rockwell Automation representative for the return procedure.Rockwell Automation maintains current product environmental information on its website at/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page.Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, T el: +90 (216) 5698400。
维贝雷利单轴稳定头（MH-100）说明书
INSTRUCTIONS: Wimberley MonoGimbal Head (MH -100)Page 1Wimberley, Inc. ©2019, All Rights Reserved Revised 190930Nylon WasherThrust WasherRadial RollerThrust BearingStainless Steel Captivating ScrewCover forBearing Assembly KnobStainless Steel Tilt ShaftSafety Stop ScrewQuick -Release ClampPage 4Quick -Release Knob Quick -ReleaseTilt KnobArca -We offer a convenient telephoto flash bracket that attaches directly to the lens plate and makes telephoto flash a breeze. down and folds for easy 6 Flash Bracket2Captivating ScrewTilt Mechanism: To disassemble the tilt mechanism, removethe captivating screw and unscrew the Tilt Knob. If you need to remove the grease in the mechanism, it is okay to use the tilt mechanism without grease until you have the opportunity to send it in for us to refurbish.Tilt Knob 2 3 1 out a QR clamp.Step 1: Install the safety stop screw compatibility warnings in included safety stop screw kit)Step 2: Open the QR clamp. The head has optional safety stop screws. These preventaccidental sliding out of the quick release. If you use these stops you must be usinga QR clamp that can be opened wide enough to load your head from the top (instead of sliding it in). See Fig 3 Step 3: Attaching the MonoGimbalPosition the flat side of the head ’s mounting base against the clamp face. Clamp it securely . Safety StopScrew InstallationFig. 3 - Attaching the MonoGimbal to a QR ClampThe monopod mountingplatform can typically beremoved if it interfereswith the full rotation of the clamp or knobs or if a lighter setup is desired.Moving JawLevel PlaneThe MonoGimbal is now ready to use. Simply loosen the tilt knob about a quarter turn and start shooting. The lens should be very easy to point, should stay pointed and should not tend to flop or creep. You can shoot with the knob loose for fluid mo-tion, or lock -in on a target by tightening the knob.If you have questions or need help setting it up, please contact us.Page 2Prerequisite: In order to attach your lens to the MonoGimbal Head, it must be fitted with an release clampwide enough so that the jaws clear therelease plate or replacementBALANCING YOUR LENS ON THE MONOPOD HEAD:STEP 1: Preparing to Balance:Tighten the Monopod Head ’s tilt knob. Mount your lens (with camera body attached). Stand behind the lens/camera setup and grab the camera body as if you are going to take a picture.If the front of the lens tilts downward you will need to slide the lens backward (toward you) in the clamp.If the front of the lens tilts upward, you will need to slide the lens forward (away from you.)PROPER HORIZONTAL BALANCE:Adjust the position of the lens in small increments until there is no tendency for it to tip.STEP 2: Balance the Horizontal Position of the Lens:Hold camera body with a relaxed grip and loosen the tilt knob of the MonoGimbal.Adjust the horizontal position of the lens forward or backwards depending on how the lens tips (see figures below). You will notice that the lens will want to tilt forward or backward. Don ’t forget to re -tighten the clamp after each adjustment.132Monopod Head on LeftSmaller lenses (e.g. the 300 f/4, 70-200 2.8) are shorter and lighter compared to most pro camera bodies. In order to balance a small lens, the quick release clamp may have to be so close to the camera body that there is not enough room for your fingers.Some solutions to this problem are using a lighter camera body or mounting the MonoGimbal to the left side of the lens (which allows much more room because of the shape of most cameras)USING SMALL LENSES (OR FOR VERTICAL SHOOTING)Monopod Head on Right Tripod Mounting foot Low -Profile Replacement Foot。
常用管道英文缩写
常用管道英文缩写默认分类2009-10-08 11:48:34 阅读73 评论0 字号：大中小ABS *Absolute 绝对的AISI *American Iron andSteel Institute 美国钢铁学会ANSI *American NationalStandards Institute 美国国家标准学会API *American Petroleum Institute 美国石油学会APPROX *Approximate 大约，近似的ASB Asbestos 石棉ASME *American Society Of Testing Material 美国机械工程师协会ASSY *Assembly 装配，组装ASTM *American Society OfTesting Material 美国材料实验协会ATM *Atmosphere 大气压AWG *American Wire Gage 美国线规AWS *American Wel**** Society 美国焊接协会AWWA *American Water WorksAssociation 美国水工协会BBB Bolted Bonnet 栓柱连接的阀盖BB By Buyer 买方供货B-B Beveled End-Beveled End 两端为坡口端BC Bolt Circle 螺栓中心圆B.C Bolted Cover(cap) 螺栓连接的阀兰盖（帽）BE Beveled End (for wel****) 坡口（焊接用）B.E Bell End 承口BEP Both Ends Plain 两端平BET Both Ends Threaded 两端带螺纹BL Battery Limit 装置区边界BF Blind Flange 法兰盖BLD Blind 盲板BLDG *Buil**** 建筑物BM Bill Of Material 材料表BOP Bottom Of Pipe 管底B-P Beveled End —Plain End 坡口端.平端BV Butterfly valve 蝶阀BWG * Birmingham Wire Gage 伯明翰线规BW Butt Weld 对焊CC Cap 管帽C-C Center to Center 中至中C-E Center to End 中至端面C-F Center to Face 中至面CH-OP Chain Operated 链条操纵的CH.PL Checkered Plate 花纹钢管C.I *Cast Iron 铸铁CL *Class 英制压力等级，等级，种类CLEAR Clearance 间隙COD Continued on Drawing 接续图COL *Column 柱，塔CONC Concentric 同心的CONN Connection 连接，接口CONT *Continue 连续CONT.V. Control Valve 控制阀CPLG Coupling 管接头，连轴节C.R. Concentric Reducer 同心异径管C.S. *Carbon Steel 碳钢C.S. Cold Spring 冷紧C.S.C. Car Seal Close 在关闭状态下封住C.S.O. Car Seal Open 在开启状态下封住CUST Customer 客C.V Check Valve 止回阀DDEG *Degree 度DF Drain funnel 排液漏斗DIA *Diameter 直径DIM *Dimension 尺寸DISCH *Discharge 出口，排出Diaphragm VELVE 隔膜阀DMF Double Male And Female 双重凹凸DN *Double Male And Female 公称直径DN Down 下DR Drain 排液DS Directional Stop 定向限为架DWG *Drawing 图EE *East 东EC External Coating 外面涂防腐层ECC Eccentric 偏心EFW Electric Fusion Welded 电容焊的EL(ELEV) *Elevation 标高；立面ELL Elbow 弯头EQIOP Equipment 设备，装置EQUIV Equivalent 相当的E.R. Eccentric Reducer 偏心异经管ERW Electric Resistance Welded 电阻焊的EW Eye Washer & Shower 洗眼器及淋浴器EXP.JT Expansion Joint 膨胀节FFDN Foundation 基础FF Flat Faced Or Full Faced 全平面；满平面F-F Face To Face 面至面FGW Fusion Gas Wel**** 气熔焊FIG *Figure 图FL Floor 楼面FLEX TUBE Flexible Tube 挠性管FLG Flange 法兰FLGD Flanged 法兰式的FLGF Flanged Face 法兰面FOB Flat On Bottom 底面平FOT Flat On Top 顶面平FP Fix Point 固定点FS Forged Steel 锻钢FTF Fitting To Fitting 管件直连FTG Fitting 管件FURND Furnished 提供的，装设的FW Field Weld 现伤焊GG Guide 导向GA *Gage 表，表压，规（线规）GALV *Galvanize 镀锌GL Ground Level 地面GLV Globe Valve 截止阀GEAR OP Gear Operated 齿轮传动的GMAW Gas Metal Arc Wel**** 金属极惰气体保护焊GSKT Gasket 垫片GTAW (Inert)Gas Tungsten Arc Wel**** 惰性气体保护钨极电弧焊GV Gate Valve 闸阀HH Hanger 吊架HC Hose Connection 软管接头H.CPLG Half Coupling 半节管接头HDR Header 总管HEX *Hexagon 六角形HF Hard Alloy Face on阀内件（阀心）为Valve Trim 硬质合金密封面HH Hand Pole 手孔HOR Horizontal 水平的H.P *High Pressure 高压HS Hose Station 软管IID *Inside Diameter 内径IN *Inch 英寸INS Insulation 隔热INST Instrument 仪表INV Invert (inside bottom of pipe) 管子内底IPS Iron Pipe size 铁管尺寸ISO Isometric Drawing 周测图（空视图）I.S.B.L Inside Battery Limit 装置边界内恻ISNS Inside screw & Non-rising Stem 内螺纹非升杆ISRS Inside screw & Rising stem 内螺纹升杆JJT Joint 接头JS Jack Screw 顶开（起）螺栓LLC Locked Closed 在关闭状态下锁定LEP Large end plain 大端为平的LET Large end Threaded 大端带螺纹LG Long 长LGF Lens Gasket Face 透镜垫连接面L.H.THD Left Hand Thread 左螺纹LIFT Lift Type 升降式LJ Lap Joint 搭接LJF Lap Joint Flange 松套法兰LO Locked Open 在开启状态下锁定L.P. Low Pressure 低压LR Long Radius 长半径LRE Long Radius Elbow 长半径弯头LTG Large Tongue & Groove 大椎槽MMATL Material 材料MAX Maximum 最大MB Machine Bolt 机器螺栓（单头）MF Male and Female 凸和凹MFG Manufacture 制造MF *Manufacture 制造厂MH Manhole 人孔MI Malleable Iron 可锻铸铁MIN *Minimum 最小MJ Mechanical Joint 机械接头M.L Match Line 连续线MSS * Manufacturers Standardization Society of the Valve and Fittings Industry, Inc.美国阀门和管件制造商标准化协会MTO Material take-off 材料统计MW Minimum Wall 最小壁厚M.W. Mineral Wool 矿（物）棉NN *North 北NB Nominal Bore 公称孔径N.B. Non-Bonnet 无阀盖NC Normally Closed 常闭NIP Nipple 短管NO Normally Open; 常开*Number号；数量NO INS No Insulation 不隔热NOM Nominal 公称的；额定的NOZ Nozzle 管口NPS Nominal Pipe Size 公称管径NPSH Net Positive Suction Head 净正吸入压头NPT *American National Taper 美国锥管螺纹Pipe ThreadNS Nominal Size 公称直径NV Needle Valve 针形阀OOD *Outside Diameter 外径OET One end Threaded 一端带螺纹OR Outside Radius 外半径ORF Orifice 孔板ORIENT Orientation 方位OS & Y Outside Screw and Yoke 外螺纹阀杆和阀轭OSNB Outside Screw Non-Bonnet 外螺纹无阀盖PP Plug 堵头PAP Piping Arrangement Plan 管道布置平面图PB Pressure Seal Bonnet 压力密封的阀盖P-B Plain End –Bevel End 平端—坡口端PC Pressure Seal Cap 压力密封的阀帽P.C.D. Pitch Circle Diameter 节圆直径PE Plain End (not beveled) 平端（无坡口）PF Platform 平台PID Piping & Instrument Diagram管道及仪表流程图PN *Nominal Pressure 公称压力PN Plant North 工厂北向POS point of Support 支承点P-P Plain End—Plain End 两端为平端PREP Preparation 加工准备PSIA *Pounds Per Square InchAbsolute 磅/PSIG Pounds Per Square Inch Gage 磅/PT Point 点PTFE *Polytetrafluoroethylene 聚四氟乙烯PT.NO Part No. 件号PV Plug Valve 旋塞阀PVC *Poly Vinyl Chloride 聚氯乙烯QQTY *Quantity 数量RR *Radius 半径RED Reducer 异径管REF Reference 参考REINF Reinforce 加强REQD Required 需要；申请REV *Revision 修改RF Raised Face 凸面RG Ring Gasket 环形垫片R.H.THD Right Hand Thread 右螺旋RJ Ring Joint 环垫接头RO Restriction Orifice 限流孔板RPM *Revolutions Per Minute 转/分RPS *Revolutions Per Second 转/秒RS Resting Support 支承架，滑动架RTJ Ring Type Joint（见RJ）RV Relief Valve 安全泄液阀SS *South 南S Spring 弹簧（管架用）SAW (Automatic)Submerged Arc Wel**** 自动埋弧焊SB Stud Bolt 双头螺栓SB Screwed Bonnet 螺纹阀盖SC Sample Cooler 取样冷却器SCH *Schedule 管壁厚系列号SCRD Screwed 螺纹SEP Small end Plain 小端为平的SET Small end Threaded 小端带螺纹SF Semi-Finished 半光SG Sight Glass 视镜SH Surface Hard Facing 硬质密封面SK Sketch 草图SMAW Shielded Metal Arc Wel**** 有保护的金属电弧焊SMLS Seamless 无缝SN Swaged Nipple 异径短管SO Slip – On 滑套SOF Slip – On Flange 滑套法兰SPEC *Specification 规定，说明SPL Sound Pressure Lever 升压水准SQ *Square 方的，平方SR Shout Radius 短半径SRE Short Radius Elbow 短半径弯头SS *Stainless Steel 不锈钢ST Steam Trap 蒸汽疏水阀STD *Standard 标准STG Small Tongue & Groove 小椎槽面STL *Steel 钢STM Steam 蒸汽STM.TR Steam Tracing 蒸汽拌热SUCT Suction 吸入口SV Safety Valve 安全泄气阀SW Socket Weld 承插焊SWG Swage 锻造，模锻SWMG Swing Type 旋启式SYM Symmetrical 对称的TT Tee 三通TE Threaded End 螺纹端TEMP *Temperature 温度TG Tongue & Groove 椎槽THD *Threaded 螺纹的THK *Thickness 厚度TL Tangent Line 切线TN True North 真实北向TOC Top of Concrete 混凝土北向TOP Top of pipe 管顶TOS Top of Support 支架顶面Top of Steel 钢结构顶面TYP Typical 典型的UUB Union Bonnet 带活接头的阀盖UC Union Cap 带活接头的阀帽UN Union 活接头VV Valve 阀VAC Vacuum 真空VAR Variable 可变的VERT Vertical 垂直的VOL *Volume 卷，册，容量，体积WW *West 西WB Weld Branch 焊接支管WC Weld Cap 焊接管帽WD Width 宽度WE Weld End 焊接端WL Wel**** Line 焊接线WN Wel**** Neck 对焊法兰（颈部）WNF Weld Neck Flange 对焊法兰WP Working Pressure 工作压力W.P. Working Point 工作点WT Wall Thickness 壁厚Weight 重量XXH Extra Heavy 加强的，加厚的XXH Double Extra Heavy 双倍加强（厚）的XS Extra Strong 加强的XXS Double Extra Strong 双倍加强的YYP Yield Point 屈服点。
数据采集器MW100基本操作
可编辑
2. 点击 “Network Config.”
© Copyright 2005 Yokogawa Electric Corporation. All Rights Reserved. G2
MW100 Prerelease Information Internal Use Only
No Mode 1 VOLT
Range
Span
Lower
Upper
100mV -75mV
75mV
Calc Refch
Scale
D.P
Lower Upper
sacle
-6000 6000
1
Unit
© Copyright 2005 Yokogawa Electric Corporation. All Rights Reserved. G2
Page.6
演示设定
打开电脑，点开本地连接，进入 属性目录，在TCP/IP标签下，设 定PC的IP地址为：192.168.1.xxx （0~100,设定的数字要比数据采 集器上设定的大）
© Copyright 2005 Yokogawa Electric Corporation. All Rights Reserved. G2
Ch.011 按测量周期分组记录 (1s) 抽值记录 : On (周期 : 4s)
MW100 Prerelease Information Internal Use Only
Page.24
记录通道设定 (1)
实行 “Apply”
选择 “001-010” 设定 Ch.1-Ch.4 对应信号发生器
Ch.001-Ch.004 按测量周期分组记录 (100ms) 抽值记录 : off
常用管道英文缩写
常用管道英文缩写默认分类2009-10-08 11:48:34 阅读73 评论0 字号：大中小ABS *Absolute 绝对的AISI *American Iron andSteel Institute 美国钢铁学会ANSI *American NationalStandards Institute 美国国家标准学会API *American Petroleum Institute 美国石油学会APPROX *Approximate 大约，近似的ASB Asbestos 石棉ASME *American Society Of Testing Material 美国机械工程师协会ASSY *Assembly 装配，组装ASTM *American Society OfTesting Material 美国材料实验协会ATM *Atmosphere 大气压AWG *American Wire Gage 美国线规AWS *American Wel**** Society 美国焊接协会AWWA *American Water WorksAssociation 美国水工协会BBB Bolted Bonnet 栓柱连接的阀盖BB By Buyer 买方供货B-B Beveled End-Beveled End 两端为坡口端BC Bolt Circle 螺栓中心圆B.C Bolted Cover(cap) 螺栓连接的阀兰盖（帽）BE Beveled End (for wel****) 坡口（焊接用）B.E Bell End 承口BEP Both Ends Plain 两端平BET Both Ends Threaded 两端带螺纹BL Battery Limit 装置区边界BF Blind Flange 法兰盖BLD Blind 盲板BLDG *Buil**** 建筑物BM Bill Of Material 材料表BOP Bottom Of Pipe 管底B-P Beveled End —Plain End 坡口端.平端BV Butterfly valve 蝶阀BWG * Birmingham Wire Gage 伯明翰线规BW Butt Weld 对焊CC Cap 管帽C-C Center to Center 中至中C-E Center to End 中至端面C-F Center to Face 中至面CH-OP Chain Operated 链条操纵的CH.PL Checkered Plate 花纹钢管C.I *Cast Iron 铸铁CL *Class 英制压力等级，等级，种类CLEAR Clearance 间隙COD Continued on Drawing 接续图COL *Column 柱，塔CONC Concentric 同心的CONN Connection 连接，接口CONT *Continue 连续CONT.V. Control Valve 控制阀CPLG Coupling 管接头，连轴节C.R. Concentric Reducer 同心异径管C.S. *Carbon Steel 碳钢C.S. Cold Spring 冷紧C.S.C. Car Seal Close 在关闭状态下封住C.S.O. Car Seal Open 在开启状态下封住CUST Customer 客C.V Check Valve 止回阀DDEG *Degree 度DF Drain funnel 排液漏斗DIA *Diameter 直径DIM *Dimension 尺寸DISCH *Discharge 出口，排出Diaphragm VELVE 隔膜阀DMF Double Male And Female 双重凹凸DN *Double Male And Female 公称直径DN Down 下DR Drain 排液DS Directional Stop 定向限为架DWG *Drawing 图EE *East 东EC External Coating 外面涂防腐层ECC Eccentric 偏心EFW Electric Fusion Welded 电容焊的EL(ELEV) *Elevation 标高；立面ELL Elbow 弯头EQIOP Equipment 设备，装置EQUIV Equivalent 相当的E.R. Eccentric Reducer 偏心异经管ERW Electric Resistance Welded 电阻焊的EW Eye Washer & Shower 洗眼器及淋浴器EXP.JT Expansion Joint 膨胀节FFDN Foundation 基础FF Flat Faced Or Full Faced 全平面；满平面F-F Face To Face 面至面FGW Fusion Gas Wel**** 气熔焊FIG *Figure 图FL Floor 楼面FLEX TUBE Flexible Tube 挠性管FLG Flange 法兰FLGD Flanged 法兰式的FLGF Flanged Face 法兰面FOB Flat On Bottom 底面平FOT Flat On Top 顶面平FP Fix Point 固定点FS Forged Steel 锻钢FTF Fitting To Fitting 管件直连FTG Fitting 管件FURND Furnished 提供的，装设的FW Field Weld 现伤焊GG Guide 导向GA *Gage 表，表压，规（线规）GALV *Galvanize 镀锌GL Ground Level 地面GLV Globe Valve 截止阀GEAR OP Gear Operated 齿轮传动的GMAW Gas Metal Arc Wel**** 金属极惰气体保护焊GSKT Gasket 垫片GTAW (Inert)Gas Tungsten Arc Wel**** 惰性气体保护钨极电弧焊GV Gate Valve 闸阀HH Hanger 吊架HC Hose Connection 软管接头H.CPLG Half Coupling 半节管接头HDR Header 总管HEX *Hexagon 六角形HF Hard Alloy Face on阀内件（阀心）为Valve Trim 硬质合金密封面HH Hand Pole 手孔HOR Horizontal 水平的H.P *High Pressure 高压HS Hose Station 软管IID *Inside Diameter 内径IN *Inch 英寸INS Insulation 隔热INST Instrument 仪表INV Invert (inside bottom of pipe) 管子内底IPS Iron Pipe size 铁管尺寸ISO Isometric Drawing 周测图（空视图）I.S.B.L Inside Battery Limit 装置边界内恻ISNS Inside screw & Non-rising Stem 内螺纹非升杆ISRS Inside screw & Rising stem 内螺纹升杆JJT Joint 接头JS Jack Screw 顶开（起）螺栓LLC Locked Closed 在关闭状态下锁定LEP Large end plain 大端为平的LET Large end Threaded 大端带螺纹LG Long 长LGF Lens Gasket Face 透镜垫连接面L.H.THD Left Hand Thread 左螺纹LIFT Lift Type 升降式LJ Lap Joint 搭接LJF Lap Joint Flange 松套法兰LO Locked Open 在开启状态下锁定L.P. Low Pressure 低压LR Long Radius 长半径LRE Long Radius Elbow 长半径弯头LTG Large Tongue & Groove 大椎槽MMATL Material 材料MAX Maximum 最大MB Machine Bolt 机器螺栓（单头）MF Male and Female 凸和凹MFG Manufacture 制造MF *Manufacture 制造厂MH Manhole 人孔MI Malleable Iron 可锻铸铁MIN *Minimum 最小MJ Mechanical Joint 机械接头M.L Match Line 连续线MSS * Manufacturers Standardization Society of the Valve and Fittings Industry, Inc.美国阀门和管件制造商标准化协会MTO Material take-off 材料统计MW Minimum Wall 最小壁厚M.W. Mineral Wool 矿（物）棉NN *North 北NB Nominal Bore 公称孔径N.B. Non-Bonnet 无阀盖NC Normally Closed 常闭NIP Nipple 短管NO Normally Open; 常开*Number号；数量NO INS No Insulation 不隔热NOM Nominal 公称的；额定的NOZ Nozzle 管口NPS Nominal Pipe Size 公称管径NPSH Net Positive Suction Head 净正吸入压头NPT *American National Taper 美国锥管螺纹Pipe ThreadNS Nominal Size 公称直径NV Needle Valve 针形阀OOD *Outside Diameter 外径OET One end Threaded 一端带螺纹OR Outside Radius 外半径ORF Orifice 孔板ORIENT Orientation 方位OS & Y Outside Screw and Yoke 外螺纹阀杆和阀轭OSNB Outside Screw Non-Bonnet 外螺纹无阀盖PP Plug 堵头PAP Piping Arrangement Plan 管道布置平面图PB Pressure Seal Bonnet 压力密封的阀盖P-B Plain End –Bevel End 平端—坡口端PC Pressure Seal Cap 压力密封的阀帽P.C.D. Pitch Circle Diameter 节圆直径PE Plain End (not beveled) 平端（无坡口）PF Platform 平台PID Piping & Instrument Diagram管道及仪表流程图PN *Nominal Pressure 公称压力PN Plant North 工厂北向POS point of Support 支承点P-P Plain End—Plain End 两端为平端PREP Preparation 加工准备PSIA *Pounds Per Square InchAbsolute 磅/PSIG Pounds Per Square Inch Gage 磅/PT Point 点PTFE *Polytetrafluoroethylene 聚四氟乙烯PT.NO Part No. 件号PV Plug Valve 旋塞阀PVC *Poly Vinyl Chloride 聚氯乙烯QQTY *Quantity 数量RR *Radius 半径RED Reducer 异径管REF Reference 参考REINF Reinforce 加强REQD Required 需要；申请REV *Revision 修改RF Raised Face 凸面RG Ring Gasket 环形垫片R.H.THD Right Hand Thread 右螺旋RJ Ring Joint 环垫接头RO Restriction Orifice 限流孔板RPM *Revolutions Per Minute 转/分RPS *Revolutions Per Second 转/秒RS Resting Support 支承架，滑动架RTJ Ring Type Joint（见RJ）RV Relief Valve 安全泄液阀SS *South 南S Spring 弹簧（管架用）SAW (Automatic)Submerged Arc Wel**** 自动埋弧焊SB Stud Bolt 双头螺栓SB Screwed Bonnet 螺纹阀盖SC Sample Cooler 取样冷却器SCH *Schedule 管壁厚系列号SCRD Screwed 螺纹SEP Small end Plain 小端为平的SET Small end Threaded 小端带螺纹SF Semi-Finished 半光SG Sight Glass 视镜SH Surface Hard Facing 硬质密封面SK Sketch 草图SMAW Shielded Metal Arc Wel**** 有保护的金属电弧焊SMLS Seamless 无缝SN Swaged Nipple 异径短管SO Slip – On 滑套SOF Slip – On Flange 滑套法兰SPEC *Specification 规定，说明SPL Sound Pressure Lever 升压水准SQ *Square 方的，平方SR Shout Radius 短半径SRE Short Radius Elbow 短半径弯头SS *Stainless Steel 不锈钢ST Steam Trap 蒸汽疏水阀STD *Standard 标准STG Small Tongue & Groove 小椎槽面STL *Steel 钢STM Steam 蒸汽STM.TR Steam Tracing 蒸汽拌热SUCT Suction 吸入口SV Safety Valve 安全泄气阀SW Socket Weld 承插焊SWG Swage 锻造，模锻SWMG Swing Type 旋启式SYM Symmetrical 对称的TT Tee 三通TE Threaded End 螺纹端TEMP *Temperature 温度TG Tongue & Groove 椎槽THD *Threaded 螺纹的THK *Thickness 厚度TL Tangent Line 切线TN True North 真实北向TOC Top of Concrete 混凝土北向TOP Top of pipe 管顶TOS Top of Support 支架顶面Top of Steel 钢结构顶面TYP Typical 典型的UUB Union Bonnet 带活接头的阀盖UC Union Cap 带活接头的阀帽UN Union 活接头VV Valve 阀VAC Vacuum 真空VAR Variable 可变的VERT Vertical 垂直的VOL *Volume 卷，册，容量，体积WW *West 西WB Weld Branch 焊接支管WC Weld Cap 焊接管帽WD Width 宽度WE Weld End 焊接端WL Wel**** Line 焊接线WN Wel**** Neck 对焊法兰（颈部）WNF Weld Neck Flange 对焊法兰WP Working Pressure 工作压力W.P. Working Point 工作点WT Wall Thickness 壁厚Weight 重量XXH Extra Heavy 加强的，加厚的XXH Double Extra Heavy 双倍加强（厚）的XS Extra Strong 加强的XXS Double Extra Strong 双倍加强的YYP Yield Point 屈服点。