结构工程常用词汇英汉对照
最全英语专业术语--机械、结构
最全英语专业术语--机械、结构模具述语一、入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口： pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座： connector socket密封/封料： seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker 四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝： screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）： mold base上内模：cavity insert下内模：core insert行位（滑块）： slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴： sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch模具述语一、入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口： pin-point gate水口大小：gate size转水口：switching runner/gate 唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座： connector socket密封/封料： seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker 四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝： screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）： mold base上内模：cavity insert下内模：core insert行位（滑块）： slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴： sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance 模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin 料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.不准用镶件： Do not use (core/cavity) insert用铍铜做镶件： use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper electrode 注塑成形不良用语aberration 色差 atomization 霚化bank mark 滞料纹 bite 咬入blacking hole 涂料孔(铸疵) blacking scab 涂料疤blister 起泡 blooming 起霜blow hole 破孔 blushing 泛白body wrinkle 侧壁皱纹 breaking-in 冒口带肉bubble 膜泡 burn mark 糊斑burr 毛边 camber 翘曲cell 气泡 center buckle 表面中部波皱check 细裂痕 checking 龟裂chipping 修整表面缺陷 clamp-off 铸件凹痕collapse 塌陷 color mottle 色斑corrosion 腐蚀 crack 裂痕crazing 碎裂 crazing 龟裂deformation 变形 edge 切边碎片edge crack 裂边 fading 退色filler speak 填充料斑 fissure 裂纹flange wrinkle 凸缘起皱 flaw 刮伤flow mark 流痕 galling 毛边glazing 光滑 gloss 光泽grease pits 污斑 grinding defect 磨痕haircrack 发裂 haze 雾度incrustation 水锈 indentation 压痕internal porosity 内部气孔 mismatch 偏模mottle 斑点 necking 缩颈nick 割痕 orange peel 橘皮状表面缺陷overflow 溢流 peeling 剥离pit 坑 pitting corrosion 点状腐蚀plate mark 模板印痕 pock 麻点pock mark 痘斑 resin streak 树脂流纹resin wear 树脂脱落 riding 凹陷sagging 松垂 saponification 皂化scar 疤痕 scrap 废料scrap jam 废料阻塞 scratch 刮伤/划痕scuffing 深冲表面划伤 seam 裂痕shock line 模口挤痕 short shot 充填不足shrinkage pool 凹孔 sink mark 凹痕skin inclusion 表皮折迭 straightening 矫直streak 条状痕 surface check 表面裂痕surface roughening 橘皮状表皮皱折 surging 波动sweat out 冒汗 torsion 扭曲warpage 翘曲 waviness 波痕webbing 熔塌 weld mark 焊痕whitening 白化 wrinkle 皱纹冲压英语stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to.to send delinery backto retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑common vocabulary for die engineering模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die 连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓alloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 硅钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel 钨钢vinyl tapped steel sheet 塑料覆面钢板模具常用刀具与工作法用语adjustable spanner 活动扳手 angle cutter 角铣刀anvil 铁钻 arbour 心轴backing 衬垫 belt sander 带式打磨机buffing 抛光 chamfering machine 倒角机chamfering tool 去角刀具 chisel 扁錾chuck 夹具 compass 两角规concave cutter 凹面铣刀 convex cutter 凸形铣刀cross joint 十字接头 cutting edge clearance 刃口余隙角drill stand 钻台 edge file 刃用锉刀file 锉刀 flange joint 凸缘接头grinder 砂轮机 hammer 铁锤hand brace 手摇钻 hatching 剖面线hexagon headed bolt 六角头螺栓 hexagon nut 六角螺帽index head 分度头 jack 千斤顶jig 治具 kit 工具箱lapping 研磨 metal saw 金工锯nose angle 刀角 pinchers 钳子pliers 铗钳 plug 柱塞头polisher 磨光器 protable driller 手提钻孔机punch 冲头 sand paper 砂纸scraper 刮刀 screw driver 螺丝起子scribing 划线 second out file 中纹锉spanner 扳手 spline broach 方栓槽拉刀square 直角尺 square sleeker 方形镘刀square trowel 直角度 stripping 剥离工具T-slot T形槽 tool for lathe 车刀tool point angle 刀刃角 tool post 刀架tosecan 划线盘 trimming 去毛边waffle die flattening 压纹效平 wiper 脱模钳wrench 螺旋扳手机床行业部分英汉对照机床行业部分英汉对照（1)：按英文字母排序3-Jaws indexing spacers 三爪、分割工具头A.T.C.system 加工中心机刀库Aluminum continuous melting & holding furnaces 连续溶解保温炉Balancing equipment 平衡设备Bayonet 卡口Bearing fittings 轴承配件Bearing processing equipment 轴承加工机Bearings 轴承Belt drive 带传动Bending machines 弯曲机Blades 刀片Blades,saw 锯片Bolts,screws & nuts 螺栓,螺帽及螺丝Boring heads 搪孔头Boring machines 镗床Cable making tools 造线机Casting,aluminium 铸铝Casting,copper 铸铜Casting,gray iron 铸灰口铁Casting,malleable iron 可锻铸铁Casting,other 其他铸造Casting,steel 铸钢Chain drive 链传动Chain making tools 造链机Chamfer machines 倒角机Chucks 夹盘Clamping/holding systems 夹具/支持系统CNC bending presses 电脑数控弯折机CNC boring machines 电脑数控镗床CNC drilling machines 电脑数控钻床CNC EDM wire-cutting machines 电脑数控电火花线切削机CNC electric discharge machines 电脑数控电火花机CNC engraving machines 电脑数控雕刻机CNC grinding machines 电脑数控磨床CNC lathes 电脑数控车床CNC machine tool fittings 电脑数控机床配件CNC milling machines 电脑数控铣床CNC shearing machines 电脑数控剪切机CNC toolings CNC刀杆CNC wire-cutting machines 电脑数控线切削机Conveying chains 输送链Coolers 冷却机Coupling 联轴器Crimping tools 卷边工具Cutters 刀具Cutting-off machines 切断机Diamond cutters 钻石刀具Dicing saws 晶圆切割机Die casting dies 压铸冲模Die casting machines 压铸机Dies-progressive 连续冲模Disposable toolholder bits 舍弃式刀头Drawing machines 拔丝机Drilling machines 钻床Drilling machines bench 钻床工作台Drilling machines,high-speed 高速钻床Drilling machines,multi-spindle 多轴钻床Drilling machines,radial 摇臂钻床Drilling machines,vertical 立式钻床drills 钻头Electric discharge machines(EDM) 电火花机Electric power tools 电动刀具Engraving machines 雕刻机Engraving machines,laser 激光雕刻机Etching machines 蚀刻机Finishing machines 修整机Fixture 夹具Forging dies 锻模Forging,aluminium 锻铝Forging,cold 冷锻Forging,copper 铜锻Forging,other 其他锻造Forging,steel 钢锻Foundry equipment 铸造设备Gear cutting machines 齿轮切削机Gears 齿轮Gravity casting machines 重力铸造机Grinder bench 磨床工作台Grinders,thread 螺纹磨床Grinders,tools & cutters 工具磨床Grinders,ultrasonic 超声波打磨机Grinding machines 磨床Grinding machines,centerless 无心磨床Grinding machines,cylindrical 外圆磨床Grinding machines,universal 万能磨床Grinding tools 磨削工具Grinding wheels 磨轮Hand tools 手工具Hard/soft and free expansion sheet making plant 硬(软) 板(片)材及自由发泡板机组Heat preserving furnaces 保温炉Heating treatment funaces 熔热处理炉Honing machines 搪磨机Hydraulic components 液压元件Hydraulic power tools 液压工具Hydraulic power units 液压动力元件Hydraulic rotary cylinders 液压回转缸Jigs 钻模Lapping machines 精研机Lapping machines,centerless 无心精研机Laser cutting 激光切割Laser cutting for SMT stensil 激光钢板切割机Lathe bench 车床工作台Lathes,automatic 自动车床Lathes,heavy-duty 重型车床Lathes,high-speed 高速车床Lathes,turret 六角车床Lathes,vertical 立式车床Lubricants 润滑液Lubrication Systems 润滑系统Lubricators 注油机Machining centers,general 通用加工中心Machining centers,horizontal 卧式加工中心Machining centers,horizontal & vertical 卧式及立式加工中心Machining centers,vertical 立式加工中心Machining centers,vertical double-column type 立式双柱加工中心Magnetic tools 磁性工具Manifolds 集合管Milling heads 铣头Milling machines 铣床Milling machines,bed type 床身式铣床Milling machines,duplicating 仿形铣床Milling machines,horizontal 卧式铣床Milling machines,turret vertical 六角立式铣床Milling machines,universal 万能铣床Milling machines,vertical 立式铣床Milling machines,vertical & horizontal 立式及卧式铣床Mold & die components 模具单元Mold changing systems 换模系统Mold core 模芯Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair 模具维修Molds 模具Nail making machines 造钉机Oil coolers 油冷却器Overflow cutting machines for aluminium wheels 铝轮冒口切断机P type PVC waterproof rolled sheet making plant P型PVC高分子防水PCB fine piecing systems 印刷电器板油压冲孔脱料系统Pipe & tube making machines 管筒制造机Planing machines 刨床Planing machines vertical 立式刨床Pneumatic hydraulic clamps 气油压虎钳Pneumatic power tools 气动工具Powder metallurgic forming machines 粉末冶金成型机Presses,cold forging 冷锻冲压机presses,crank 曲柄压力机Presses,eccentric 离心压力机Presses,forging 锻压机Presses,hydraulic 液压冲床Presses,knuckle joint 肘杆式压力机Presses,pneumatic 气动冲床Presses,servo 伺服冲床Presses,transfer 自动压力机Pressing dies 压模Punch formers 冲子研磨器Quick die change systems 速换模系统Quick mold change systems 快速换模系统Reverberatory furnaces 反射炉Rollers 滚筒Rolling machines 辗压机Rotary tables 转台Sawing machines 锯床Sawing machines,band 带锯床Saws,band 带锯Saws,hack 弓锯Saws,horizontal band 卧式带锯Saws,vertical band 立式带锯shafts 轴Shapers 牛头刨床Shearing machines 剪切机Sheet metal forming machines 金属板成型机Sheet metal working machines 金属板加工机Slotting machines 插床spindles 主轴Stamping parts 冲压机Straightening machines 矫直机Switches & buttons 开关及按钮Tapping machines 攻螺丝机Transmitted chains 传动链Tube bending machines 弯管机Vertical hydraulic broaching machine 立式油压拉床Vises 虎钳Vises,tool-maker 精密平口钳Wheel dressers 砂轮修整器Woven-Cutting machines 织麦激光切割机Wrenches 扳手表面处理关连用语age hardening 时效硬化 ageing 老化处理air hardening 气体硬化 air patenting 空气韧化annealing 退火anode effect 阳极效应anodizing 阳极氧化处理 atomloy treatment 阿扥木洛伊表面austempering 奥氏体等温淬火 austenite 奥斯田体/奥氏体bainite 贝氏体 banded structure 条纹状组织barrel plating 滚镀 barrel tumbling 滚筒打光blackening 染黑法 blue shortness 青熟脆性bonderizing 磷酸盐皮膜处理 box annealing 箱型退火box carburizing 封箱渗碳 bright electroplating 辉面电镀bright heat treatment 光辉热处理 bypass heat treatment旁路热处理carbide 炭化物 carburized case depth 浸碳硬化深层carburizing 渗碳 cementite 炭化铁chemical plating 化学电镀 chemical vapor deposition化学蒸镀coarsening 结晶粒粗大化 coating 涂布被覆cold shortness 低温脆性 comemtite 渗碳体controlled atmosphere 大气热处理 corner effect 锐角效应creeping discharge 蠕缓放电 decarburization 脱碳处理decarburizing 脱碳退火 depth of hardening 硬化深层diffusion 扩散 diffusion annealing 扩散退火electrolytic hardening 电解淬火 embossing 压花etching 表面蚀刻 ferrite 肥粒铁first stage annealing 第一段退火 flame hardening 火焰硬化flame treatment 火焰处理 full annealing 完全退火gaseous cyaniding 气体氧化法 globular cementite 球状炭化铁grain size 结晶粒度 granolite treatment 磷酸溶液热处理graphitizing 石墨退火 hardenability 硬化性hardenability curve 硬化性曲线 hardening 硬化heat treatment 热处理 hot bath quenching 热浴淬火hot dipping 热浸镀 induction hardening 高周波硬化ion carbonitriding 离子渗碳氮化 ion carburizing 离子渗碳处理ion plating 离子电镀 isothermal annealing 等温退火liquid honing 液体喷砂法 low temperature annealing 低温退火malleablizing 可锻化退火 martempering 麻回火处理martensite 马氏体/硬化铁炭 metallikon 金属喷镀法metallizing 真空涂膜 nitriding 氮化处理nitrocarburizing 软氮化 normalizing 正常化oil quenching 油淬化 overageing 过老化overheating 过热 pearlite 针尖组织phosphating 磷酸盐皮膜处理 physical vapor deposition 物理蒸镀plasma nitriding 离子氮化 pre-annealing 预备退火precipitation 析出 precipitation hardening 析出硬化press quenching 加压硬化 process annealing 制程退火quench ageing 淬火老化 quench hardening 淬火quenching crack 淬火裂痕 quenching distortion 淬火变形quenching stress 淬火应力 reconditioning 再调质recrystallization 再结晶 red shortness 红热脆性residual stress 残留应力 retained austenite 残留奥rust prevention 防蚀 salt bath quenching 盐浴淬火sand blast 喷砂处理 seasoning 时效处理second stage annealing 第二段退火 secular distortion 经年变形segregation 偏析 selective hardening 部分淬火shot blast 喷丸处理 shot peening 珠击法single stage nitriding 等温渗氮 sintering 烧结处理soaking 均热处理 softening 软化退火solution treatment 固溶化热处理 spheroidizing 球状化退火stabilizing treatment 安定化处理 straightening annealing 矫直退火strain ageing 应变老化 stress relieving annealing 应力消除退火subzero treatment 生冷处理 supercooling 过冷surface hardening 表面硬化处理 temper brittleness 回火脆性temper colour 回火颜色 tempering 回火tempering crack 回火裂痕 texture 咬花thermal refining 调质处理 thermoechanical treatment加工热处理time quenching 时间淬火 transformation 变态tufftride process 软氮化处理 under annealing 不完全退火vacuum carbonitriding 真空渗碳氮化 vacuumcarburizing 真空渗碳处理vacuum hardening 真空淬火 vacuum heat treatment 真空热处理vacuum nitriding 真空氮化 water quenching 水淬火wetout 浸润处理常用塑料英语缩略语一英文简称英文全称中文全称ABA Acrylonitrile-butadiene-acrylate 丙烯腈/丁二烯/丙烯酸酯共聚物ABS Acrylonitrile-butadiene-styrene 丙烯腈/丁二烯/苯乙烯共聚物AES Acrylonitrile-ethylene-styrene 丙烯腈/乙烯/苯乙烯共聚物AMMA Acrylonitrile/methyl Methacrylate 丙烯腈/甲基丙烯酸甲酯共聚物ARP Aromatic polyester 聚芳香酯AS Acrylonitrile-styrene resin 丙烯腈-苯乙烯树脂ASA Acrylonitrile-styrene-acrylate 丙烯腈/苯乙烯/丙烯酸酯共聚物CA Cellulose acetate 醋酸纤维塑料CAB Cellulose acetate butyrate 醋酸-丁酸纤维素塑料CAP Cellulose acetate propionate 醋酸-丙酸纤维素CE Cellulose plastics, general 通用纤维素塑料CF Cresol-formaldehyde 甲酚-甲醛树脂CMC Carboxymethyl cellulose 羧甲基纤维素CN Cellulose nitrate 硝酸纤维素CP Cellulose propionate 丙酸纤维素CPE Chlorinated polyethylene 氯化聚乙烯CPVC Chlorinated poly(vinyl chloride) 氯化聚氯乙烯CS Casein 酪蛋白CTA Cellulose triacetate 三醋酸纤维素EC Ethyl cellulose 乙烷纤维素EMA Ethylene/methacrylic acid 乙烯/甲基丙烯酸共聚物EP Epoxy, epoxide 环氧树脂EPD Ethylene-propylene-diene 乙烯-丙烯-二烯三元共聚物EPM Ethylene-propylene polymer 乙烯-丙烯共聚物EPS Expanded polystyrene 发泡聚苯乙烯ETFE Ethylene-tetrafluoroethylene 乙烯-四氟乙烯共聚物EVA Ethylene/vinyl acetate 乙烯-醋酸乙烯共聚物EVAL Ethylene-vinyl alcohol 乙烯-乙烯醇共聚物FEP Perfluoro(ethylene-propylene) 全氟（乙烯-丙烯）塑料FF Furan formaldehyde 呋喃甲醛HDPE High-density polyethylene plastics高密度聚乙烯塑料HIPS High impact polystyrene 高冲聚苯乙烯IPS Impact-resistant polystyrene 耐冲击聚苯乙烯LCP Liquid crystal polymer 液晶聚合物LDPE Low-density polyethylene plastics 低密度聚乙烯塑料LLDPE Linear low-density polyethylene 线性低密聚乙烯LMDPE Linear medium-density polyethylene 线性中密聚乙烯MBS Methacrylate-butadiene-styrene 甲基丙烯酸-丁二烯-苯乙烯共聚物MDPE Medium-density polyethylene 中密聚乙烯MF Melamine-formaldehyde resin 密胺-甲醛树脂MPF Melamine/phenol-formaldehyde 密胺/酚醛树脂常用塑料英语缩略语二英文简称英文全称中文全称PA Polyamide (nylon) 聚酰胺（尼龙）PAA Poly(acrylic acid) 聚丙烯酸PADC Poly(allyl diglycol carbonate) 碳酸-二乙二醇酯·烯丙醇酯树脂PAE Polyarylether 聚芳醚PAEK Polyaryletherketone 聚芳醚酮PAI Polyamide-imide 聚酰胺-酰亚胺PAK Polyester alkyd 聚酯树脂PAN Polyacrylonitrile 聚丙烯腈PARA Polyaryl amide 聚芳酰胺PASU Polyarylsulfone 聚芳砜PAT Polyarylate 聚芳酯PAUR Poly(ester urethane) 聚酯型聚氨酯PB Polybutene-1 聚丁烯-[1]PBA Poly(butyl acrylate) 聚丙烯酸丁酯PBAN Polybutadiene-acrylonitrile 聚丁二烯-丙烯腈PBS Polybutadiene-styrene 聚丁二烯-苯乙烯PBT Poly(butylene terephthalate) 聚对苯二酸丁二酯PC Polycarbonate 聚碳酸酯PCTFE Polychlorotrifluoroethylene 聚氯三氟乙烯PDAP Poly(diallyl phthalate) 聚对苯二甲酸二烯丙酯PE Polyethylene 聚乙烯PEBA Polyether block amide 聚醚嵌段酰胺PEBA Thermoplastic elastomer polyether 聚酯热塑弹性体PEEK Polyetheretherketone 聚醚醚酮PEI Poly(etherimide) 聚醚酰亚胺PEK Polyether ketone 聚醚酮PEO Poly(ethylene oxide) 聚环氧乙烷PES Poly(ether sulfone) 聚醚砜PET Poly(ethylene terephthalate) 聚对苯二甲酸乙二酯PETG Poly(ethylene terephthalate) glycol 二醇类改性PETPEUR Poly(ether urethane) 聚醚型聚氨酯PF Phenol-formaldehyde resin 酚醛树脂PFA Perfluoro(alkoxy alkane) 全氟烷氧基树脂PFF Phenol-furfural resin 酚呋喃树脂PI Polyimide 聚酰亚胺PIB Polyisobutylene 聚异丁烯PISU Polyimidesulfone 聚酰亚胺砜PMCA Poly(methyl-alpha-chloroacrylate) 聚α-氯代丙烯酸甲酯PMMA Poly(methyl methacrylate) 聚甲基丙烯酸甲酯PMP Poly(4-methylpentene-1) 聚4-甲基戊烯-1 PMS Poly(alpha-methylstyrene) 聚α-甲基苯乙烯POM Polyoxymethylene, polyacetal 聚甲醛PP Polypropylene 聚丙烯PPA Polyphthalamide 聚邻苯二甲酰胺PPE Poly(phenylene ether) 聚苯醚PPO Poly(phenylene oxide) deprecated 聚苯醚PPOX Poly(propylene oxide) 聚环氧（丙）烷PPS Poly(phenylene sulfide) 聚苯硫醚PPSU Poly(phenylene sulfone) 聚苯砜PS Polystyrene 聚苯乙烯PSU Polysulfone 聚砜PTFE Polytetrafluoroethylene 聚四氟乙烯PUR Polyurethane 聚氨酯PVAC Poly(vinyl acetate) 聚醋酸乙烯PVAL Poly(vinyl alcohol) 聚乙烯醇PVB Poly(vinyl butyral) 聚乙烯醇缩丁醛PVC Poly(vinyl chloride) 聚氯乙烯PVCA Poly(vinyl chloride-acetate) 聚氯乙烯醋酸乙烯酯PVDC Poly(vinylidene chloride) 聚（偏二氯乙烯）PVDF Poly(vinylidene fluoride) 聚（偏二氟乙烯）PVF Poly(vinyl fluoride) 聚氟乙烯PVFM Poly(vinyl formal) 聚乙烯醇缩甲醛PVK Polyvinylcarbazole 聚乙烯咔唑PVP Polyvinylpyrrolidone 聚乙烯吡咯烷酮S/MA Styrene-maleic anhydride plastic 苯乙烯-马来酐塑料SAN Styrene-acrylonitrile plastic 苯乙烯-丙烯腈塑料SB Styrene-butadiene plastic 苯乙烯-丁二烯塑料Si Silicone plastics 有机硅塑料SMS Styrene/alpha-methylstyrene plastic 苯乙烯-α-甲基苯乙烯塑料SP Saturated polyester plastic 饱和聚酯塑料SRP Styrene-rubber plastics 聚苯乙烯橡胶改性塑料TEEE Thermoplastic Elastomer,Ether-Ester 醚酯型热塑弹性体TEO Thermoplastic Elastomer, Olefinic 聚烯烃热塑弹性体TES Thermoplastic Elastomer, Styrenic 苯乙烯热塑性弹性体TPEL Thermoplastic elastomer 热塑(性)弹性体TPES Thermoplastic polyester 热塑性聚酯TPUR Thermoplastic polyurethane 热塑性聚氨酯TSUR Thermoset polyurethane 热固聚氨酯UF Urea-formaldehyde resin 脲甲醛树脂UHMWPE Ultra-high molecular weight PE 超高分子量聚乙烯UP Unsaturated polyester 不饱和聚酯VCE Vinyl chloride-ethylene resin 氯乙烯/乙烯树脂VCEV Vinyl chloride-ethylene-vinyl 氯乙烯/乙烯/醋酸乙烯共聚物VCMA Vinyl chloride-methyl acrylate 氯乙烯/丙烯酸甲酯共聚物VCMMA Vinyl chloride-methylmethacrylate 氯乙烯/甲基丙烯酸甲酯共聚物VCOA Vinyl chloride-octyl acrylate resin 氯乙烯/丙烯酸辛酯树脂VCVAC Vinyl chloride-vinyl acetate resin 氯乙烯/醋酸乙烯树脂VCVDC Vinyl chloride-vinylidene chloride 氯乙烯/偏氯乙烯共聚物模具术语punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣机械词汇Piping work: 铺管工程Steam trace: 加热蒸汽管道Cutting: 切割socket weld承插焊接fillet weld角焊,填角焊branch connection分支接续fabrication tolerance.制造容差local heat treatment 局部热处理threaded pipe螺纹管seal welding.密封焊接flange joint 凸缘接头undercut 底切feeder馈电线conduit outlet电线引出口seal fitting 密封接头, 密封配件Screw thread lubricant螺纹润滑剂Seal: 绝缘层weld reinforcement 焊缝补强lock washer 锁紧[止动, 防松]垫圈electrical panel.配电板,配电盘nipple螺纹接头zinc plated.镀锌的ring joint 环接, 围缘接合bolt 螺栓control: 控制器National Electrical Code 全国电气规程master schedule 主要图表, 综合图表, 设计任务书, 主要作业表torque wrench 转矩扳手job site 施工现场flange connection.凸缘联接Hard hat：安全帽Goggles：护目镜stockpile贮存packing list装箱单crate: 柳条箱purchased material list原材料进货单back-feed反馈wire coil线盘，线卷，NPT thread. 美国标准锥管螺纹cable gland 电缆衬垫terminal block线弧, 接头排接线盒, 接线板, 线夹power drill机械钻connector. 接线器insulated sleeve绝缘套管wire connector接线器wire terminal电线接头control wiring控制线路motor lead电动机引出线power wiring电力布线tender document．提供证件orifice plate.挡板nut 螺母flange gasket 法兰垫片dimensional inspection 尺寸检验burn through 烧蚀piping system.管道系统reinforcement of weld加强焊缝fabrication.制造dye penetrant examination染料渗透试验法magnetic particle examination 磁粉检验girth weld环形焊缝cement lined piping 水泥衬里weld joint 焊缝, 焊接接头spool drawing 管路图, 管路详图spot test 抽查, 当场测试butt weld 对接焊缝Random Radiography随机射线照相检查radiographic examination 射线照相检查assembly.装配erection 架设examination试验cable tray.电缆盘rigid steel conduit 钢制电线管power control 功率控制arc welding 电弧焊control cable控制电缆操纵索normal bend 法向[法线]弯管cable glands: 电缆衬垫exfoliation剥落power receptacle 电力插座grounding conductor 接地导体lighting fixture照明器材junction box 分线箱race way 电缆管道terminal box接线盒distribution board配电盘, 配电屏receptacle 插座tumble switch.翻转开关,拨动式开关cathodic protection system 阴极保护系统Circuit breaker断路开关amplifier panel 放大器盘control console 控制台electrical material电气材料convenience receptacle.电源插座cable gland 电缆衬垫TIG： Tungsten-arc Inert-Gas welding 钨极电弧惰性气体保护焊filler rod焊条tensile strength 抗张强度shield gas 保护气体shield jig保护夹具high frequency generator.高频发电机welding rod 焊条filler metal 焊料, 焊丝shop fabrication 车间制造field installation 现场安装welding bead 焊道both sides welding.双面焊接residual stress 残余应力electrode 电焊条condensation 冷凝longitudinal.纵向的horizontal line 水平线circumferential joint 周圈接缝nondestructive examination.非破坏性检验, qualification: 合格性construction work施工工程welded joint焊接缝焊接节点gas cutting.气割arc cutting电弧切割grind off 磨掉metallic luster 金属光泽Screwed Piping Joints螺丝状的管接头gouging .刨削槽Bending: 挠曲witness test订货人在场的试验Welding: 焊接Threading: 车缧纹Leveling：校平color identification 彩色识别Alignment：对准,定位调整check against 检查, 核对Fixing：固定Console：控制台cubicle室,箱audit 审计material certificate.材料合格证vertical panel竖直面板power distribution panel 配电盘gauge board仪表板beveling 磨斜棱,磨斜边local panel 现场配电盘grouting 灌浆fabrication 加工,制造instrument rack 计测器支架tank gauge 液面计flushing 冲洗，填缝analyzer分析器piping管道敷设tubing敷设管道cable fitting电缆配件elbow.弯管接头main pipe 主管道bend.弯管弯头solvent 溶剂postweld heat treatment 焊后热处理jig.夹具arc gouging 电弧刨削chipping修琢machining 机械加工bridges.管式桥clamp.夹钳tack welding 点焊butt welding 对接焊grinder. 磨床commencement.开始gusset plate角撑板, 加固板process pipe 工艺管道land 纹间表面tee 三通管丁字钢 T形梁opening 开口reinforcing pad.补强垫,增强衬板flux 焊剂wet developer 湿显像剂blowhole气泡,气孔inclusion 杂质imperfection 缺陷limitation 限度valve 阀,闸门structural attachment 结构附件tapered allowance 削尖余量tack welding 平头焊接。
常用机械加工工艺术语英汉对照
常用机械加工工艺术语英汉对照1. 弯曲（Bending）中文译名：弯曲定义：将工件或材料沿着一定弯曲半径的轴线弯成所需形状的工艺。
常见英文词汇： Bending、Bend常见应用场景：金属板件的弯曲加工、管道的折弯等。
2. 铣削（Milling）中文译名：铣削定义：利用铣刀在工件上旋转切削的方法，将工件表面的不规则部分切削成平整的形状。
常见英文词汇： Milling、Milling cutter常见应用场景：金属、塑料等工件的表面加工、平面铣削等。
3. 钻削（Drilling）中文译名：钻削定义：利用钻头在工件上旋转切削的方法，将工件表面钻出孔洞。
常见英文词汇： Drilling、Drill常见应用场景：金属、木材等工件的孔洞加工、螺纹加工等。
4. 拉伸（Stretching）中文译名：拉伸定义：利用外力施加在工件上，使工件拉长或变形的一种加工方法。
常见英文词汇： Stretching、Stretch常见应用场景：金属板材的拉伸成型、塑料薄膜的拉伸加工等。
5. 折弯（Folding）中文译名：折弯定义：将工件沿一定的折弯线折弯或折叠的一种工艺。
常见英文词汇： Folding、Fold常见应用场景：金属片的折叠加工、纸张等的折叠加工等。
6. 车削（Turning）中文译名：车削定义：利用车床上旋转的工件，通过刀具的切削将工件外形加工成所需形状的一种方法。
常见英文词汇： Turning、Turn常见应用场景：圆柱形工件的精密加工、内外圆柱的加工等。
7. 切削（Cutting）中文译名：切削定义：利用刀具沿工件表面进行切削的过程，将工件切割、修整或产生新的形状。
常见英文词汇： Cutting、Cut常见应用场景：金属、木材等工件的切割、修整等。
8. 研磨（Grinding）中文译名：研磨定义：利用磨料通过相对运动与工件表面进行切削、磨削的一种加工方法。
常见英文词汇： Grinding、Grind常见应用场景：金属、陶瓷等材料的表面处理、精加工等。
建筑施工名词中英文对照
建筑施工名词中英文对照建筑施工是一个复杂而细致的过程，其中涉及大量的专业名词。
对于从事建筑施工行业的人士来说，掌握这些名词的中英文对照是非常重要的。
本文将介绍一些常用的建筑施工名词的中英对照，帮助读者更好地理解和运用这些术语。
1. Foundation - 基础基础是建筑物最底部的结构，通常是混凝土的平面，用来支撑整个建筑物的重量。
2. Reinforced concrete - 钢筋混凝土钢筋混凝土是一种由混凝土和钢筋组成的材料，具有高强度和耐久性，广泛应用于建筑施工中。
3. Masonry - 砌体结构砌体结构是一种由砖块或石块按照一定的方式砌筑而成的结构，常用于建筑物的墙体和隔墙。
4. Column - 柱子柱子是一种纵向的结构元素，通常用于支撑建筑物的荷载，并传递到基础。
5. Beam - 梁梁是一种横向的结构元素，通常用于支撑楼板和屋顶，并将荷载传递到柱子上。
6. Slab - 板板是建筑物的水平支撑结构，通常用于构成楼板、屋顶和平台等。
7. Wall - 墙体墙体是建筑物的竖向结构，通常用于分隔空间并承受水平荷载。
8. Roof - 屋顶屋顶是建筑物的最顶部覆盖结构，用于保护建筑物免受自然环境的影响。
9. Foundation pit - 基坑基坑是在施工过程中挖掘的一个具有一定深度和形状的空间，用于建筑物的基础施工。
10. Excavation - 开挖开挖是指移除地表土壤或岩石以形成基坑或其它结构的过程。
11. Pile - 桩基桩基是在土壤或岩石中打入的长桩，用于增加地基的稳定性和承载能力。
12. Formwork - 模板模板是一种用于在混凝土浇筑过程中支撑和成型的结构，通常由木材或金属构造而成。
13. Rebar - 钢筋钢筋是一种用于增加混凝土结构强度的金属材料，通常以长条形式使用。
14. Concrete mixer - 混凝土搅拌机混凝土搅拌机是一种用于将水泥、沙子、石子和水混合制成混凝土的设备。
结构工程常用英语词汇
结构工程常用英语词汇混凝土：concrete 钢筋：reinforcing steel bar钢筋混凝土：reinforced concrete（RC）钢筋混凝土结构：reinforced concrete structure板式楼梯：cranked slab stairs 刚度：rigidity徐变：creep 水泥：cement钢筋保护层：cover to reinforcement 梁：beam柱：column 板：slab 剪力墙：shear wall 基础：foundation剪力：shear 剪切变形：shear deformation 剪切模量：shear modulus拉力：tension 压力：pressure 延伸率：percentage of elongation位移：displacement 应力：stress 应变：strain应力集中：concentration of stresses 应力松弛：stress relaxation 应力图：stress diagram 应力应变曲线：stress-strain curve 应力状态：state of stress 钢丝：steel wire 箍筋：hoop reinforcement 箍筋间距：stirrup spacing 加载：loading抗压强度：compressive strength 抗弯强度：bending strength抗扭强度：torsional strength 抗拉强度：tensile strength裂缝：crack 屈服：yield 屈服点：yield point 屈服荷载：yield load屈服极限：limit of yielding 屈服强度：yield strength屈服强度下限：lower limit of yield 荷载：load 横截面：cross section 承载力：bearing capacity 承重结构：bearing structure弹性模量：elastic modulus 预应力钢筋混凝土：prestressed reinforced concrete 预应力钢筋：prestressed reinforcement 预应力损失：loss of prestress 预制板：precast slab现浇钢筋混凝土结构：cast-in-place reinforced concrete双向配筋：two-way reinforcement 主梁：main beam次梁：secondary beam 弯矩：moment 悬臂梁：cantilever beam延性：ductileity受弯构件：member in bending 受拉区：tensile region 受压区：compressive region 塑性：plasticity轴向压力：axial pressure 轴向拉力：axial tension吊车梁：crane beam 可靠性：reliability 粘结力：cohesive force外力：external force 弯起钢筋：bent-up bar 弯曲破坏：bending failure 屋架：roof truss 素混凝土：non-reinforced concrete无梁楼盖：flat slab 配筋率：reinforcement ratio配箍率：stirrup ratio 泊松比：Poisson’s ratio偏心受拉：eccentric tension 偏心受压：eccentric compression偏心距：eccentric distance 疲劳强度：fatigue strength偏心荷载：eccentric load 跨度：span 跨高比：span-to-depth ratio跨中荷载：midspan load 框架结构：frame structure集中荷载：concentrated load 分布荷载：distribution load分布钢筋：distribution steel 挠度：deflection设计荷载：design load 设计强度：design strength构造：construction 简支梁：simple beam 截面面积：area of section 浇注：pouring 浇注混凝土：concreting钢筋搭接：bar splicing 刚架：rigid frame脆性：brittleness 脆性破坏：brittle failure。
土木工程常用英语术语
土木工程常用英语术语第一节普通术语1. 工程结构building and civil engineering structures2. 工程结构设计design of building and civil engineering structures3. 房屋建造工程building engineering5. 马路工程highway engineering6. 铁路工程railway engineering10. 建造物（构筑物）construction works11. 结构structure12. 基础foundation13. 地基foundation soil; subgrade; subbase; ground14. 木结构timber structure15. 砌体结构masonry structure16. 钢结构steel structure17.混凝土（砼）结构concrete structure以混凝土为主制作的结构。
它包括素混凝土结构、钢筋混凝土结构和预应力混凝土结构等。
18. 特种工程结构special engineering structure20.工业建造industrial building21. 民用建造civil building; civil architecture22. 马路highway24. 高速马路freeway32. 铁路车站railway station33. 港口port; harbour39. 水库reservoir40. 水工建造物hydraulic structure; marine structure; maritime construction50. 安全设施safety device第二节房屋建造结构术语第 1 页/共23 页1. 混合结构mixed structure2. 板柱结构slab-colume system3. 框架结构frame structure6. 壳体结构shell structure8. 悬索结构cable-suspended structure21.9. 充气结构pneumatic structure10. 剪力墙（结构墙）结构shear wall structure在高层和多层建造中，竖向和水平作用均由钢筋混凝土或预应力混凝土墙体承受的结构。
机械行业常用英语对照--机械英语
机械行业常用英语对照--机械英语2010年09月05日星期日下午 09:34stamping, press冲压punch press, dieing out press冲床uncoiler &strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上逝世点bottom stop下逝世点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to.to send delinery backto retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption耗费to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑common vocabulary for die engineering 模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die 持续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变更die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓机械行业部分英汉对照按英文字母排序3-Jaws indexing spacers 三爪、分割工具头A.T.C.system 加工中心机刀库Aluminum continuous melting &holding furnaces 持续溶解保温炉Balancing equipment 平衡设备Bayonet 卡口Bearing fittings 轴承配件Bearing processing equipment 轴承加工机Bearings 轴承Belt drive 带传动Bending machines 弯曲机Blades 刀片Blades,saw 锯片Bolts,screws &nuts 螺栓,螺帽及螺丝Boring heads 搪孔头Boring machines 镗床Cable making tools 造线机Casting,aluminium 铸铝Casting,copper 铸铜Casting,gray iron 铸灰口铁Casting,malleable iron 可锻铸铁Casting,other 其他铸造Casting,steel 铸钢Chain drive 链传动Chain making tools 造链机Chamfer machines 倒角机Chucks 夹盘Clamping/holding systems 夹具/支撑系统CNC bending presses 电脑数控弯折机CNC boring machines 电脑数控镗床CNC drilling machines 电脑数控钻床CNC EDM wire-cutting machines 电脑数控电火花线切削机CNC electric discharge machines 电脑数控电火花机CNC engraving machines 电脑数控雕刻机CNC grinding machines 电脑数控磨床CNC lathes 电脑数控车床CNC machine tool fittings 电脑数控机床配件CNC milling machines 电脑数控铣床CNC shearing machines 电脑数控剪切机CNC toolings CNC刀杆CNC wire-cutting machines 电脑数控线切削机Conveying chains 输送链Coolers 冷却机Coupling 联轴器Crimping tools 卷边工具Cutters 刀具Cutting-off machines 切断机Diamond cutters 钻石刀具Dicing saws 晶圆切割机Die casting dies 压铸冲模Die casting machines 压铸机Dies-progressive 持续冲模Disposable toolholder bits 舍弃式刀头Drawing machines 拔丝机Drilling machines 钻床Drilling machines bench 钻床工作台Drilling machines,high-speed 高速钻床Drilling machines,multi-spindle 多轴钻床Drilling machines,radial 摇臂钻床Drilling machines,vertical 立式钻床drills 钻头Electric discharge machines(EDM) 电火花机Electric power tools 电动刀具Engraving machines 雕刻机Engraving machines,laser 激光雕刻机Etching machines 蚀刻机Finishing machines 修整机Fixture 夹具Forging dies 锻模Forging,aluminium 锻铝Forging,cold 冷锻Forging,copper 铜锻Forging,other 其他锻造Forging,steel 钢锻Foundry equipment 铸造设备Gear cutting machines 齿轮切削机Gears 齿轮Gravity casting machines 重力铸造机Grinder bench 磨床工作台Grinders,thread 螺纹磨床Grinders,tools &cutters 工具磨床Grinders,ultrasonic 超声波打磨机Grinding machines 磨床Grinding machines,centerless 无心磨床Grinding machines,cylindrical 外圆磨床Grinding machines,universal 全能磨床Grinding tools 磨削工具Grinding wheels 磨轮Hand tools 手工具Hard/soft and free expansion sheet making plant 硬(软)板(片)材及自由发泡板机组Heat preserving furnaces 保温炉Heating treatment funaces 熔热处理炉Honing machines 搪磨机Hydraulic components 液压元件Hydraulic power tools 液压工具Hydraulic power units 液压动力元件Hydraulic rotary cylinders 液压回转缸Jigs 钻模Lapping machines 精研机Lapping machines,centerless 无心精研机Laser cutting 激光切割Laser cutting for SMT stensil 激光钢板切割机Lathe bench 车床工作台Lathes,automatic 主动车床Lathes,heavy-duty 重型车床Lathes,high-speed 高速车床Lathes,turret 六角车床Lathes,vertical 立式车床Lubricants 润滑液Lubrication Systems 润滑系统Lubricators 注油机Machining centers,general 通用加工中心Machining centers,horizontal 卧式加工中心Machining centers,horizontal &vertical 卧式及立式加工中心Machining centers,vertical 立式加工中心Machining centers,vertical double-column type 立式双柱加工中心Magnetic tools 磁性工具Manifolds 集合管Milling heads 铣头Milling machines 铣床Milling machines,bed type 床身式铣床Milling machines,duplicating 仿形铣床Milling machines,horizontal 卧式铣床Milling machines,turret vertical 六角立式铣床Milling machines,universal 全能铣床Milling machines,vertical 立式铣床Milling machines,vertical &horizontal 立式及卧式铣床Mold &die components 模具单元Mold changing systems 换模系统Mold core 模芯Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair 模具维修Molds 模具Nail making machines 造钉机Oil coolers 油冷却器Overflow cutting machines for aluminium wheels 铝轮冒口切断机P type PVC waterproof rolled sheet making plant P型PVC高分子防水PCB fine piecing systems 印刷电器板油压冲孔脱料系统Pipe &tube making machines 管筒制作机Planing machines 刨床Planing machines vertical 立式刨床Pneumatic hydraulic clamps 气油压虎钳Pneumatic power tools 气动工具Powder metallurgic forming machines 粉末冶金成型机Presses,cold forging 冷锻冲压机presses,crank 曲柄压力机Presses,eccentric 离心压力机Presses,forging 锻压机Presses,hydraulic 液压冲床Presses,knuckle joint 肘杆式压力机Presses,pneumatic 气动冲床Presses,servo 伺服冲床Presses,transfer 主动压力机Pressing dies 压模Punch formers 冲子研磨器Quick die change systems 速换模系统Quick mold change systems 快速换模系统Reverberatory furnaces 反射炉Rollers 滚筒Rolling machines 辗压机Rotary tables 转台Sawing machines 锯床Sawing machines,band 带锯床Saws,band 带锯Saws,hack 弓锯Saws,horizontal band 卧式带锯Saws,vertical band 立式带锯shafts 轴Shapers 牛头刨床Shearing machines 剪切机Sheet metal forming machines 金属板成型机Sheet metal working machines 金属板加工机Slotting machines 插床spindles 主轴Stamping parts 冲压机Straightening machines 矫直机Switches &buttons 开关及按钮Tapping machines 攻螺丝机Transmitted chains 传动链Tube bending machines 弯管机Vertical hydraulic broaching machine 立式油压拉床Vises 虎钳Vises,tool-maker 精密平口钳Wheel dressers 砂轮修整器Woven-Cutting machines 织麦激光切割机Wrenches 扳手。
英汉化工设计施工图解词汇
Layout
8.2管道材料 2
Piping Material
3 8.3管道机械
Piping Mechanics
4 8.4地下管道
Underground Piping
5
8.5绝热 Insulation
8.6工程图常用缩写 词（按字母顺序排列）
Abbreviations for Use on
Drawing （in Alphabetical
2.3化工企 业三废污染 控0 3制 Chemical Industri al Enterpri se Wastes Pollutio n Control
20 .4 4 大 气 污 染物扩散 Air Pollutan t Dispersi on
05
2.5固体废 弃物处理 Waste Solid Treatmen t
1006 . 6 控 制 及保护器件 Control and Protecti on Devices
10.8供电系统 Power Supply
System
10.7电气防爆设备 Explosion Protected Apparatus
10.9电线、电缆及 附件 Wires， Cables and
Accessories
1.4工艺流程模拟计 算 Process Flowsheet Simulation
2.1化工企 业排放的主 要0 1污 染 物 Pollutan ts Discharg ed by Chemical Industri al Enterpri se
02
2.2环境质 量 Environm ental Quality
仪表 Level Meter
5 9.5过程分析
仪表 Process Analyzer
(新)模具术语英汉对照-aberration 色差_
aberration 色差atomization 霚化bank mark 滞料纹bite 咬入blacking hole 涂料孔(铸疵) blacking scab 涂料疤blister 起泡blooming 起霜blow hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡center buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕orange peel 橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap 废料scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮折迭straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱折surging 波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位qualified products, up-to-grade products良品defective products, not up-to-grade products不良品waste废料。
工程英汉对照表
工程英语英汉对照词汇表编者前言：鉴于项目管理和施工需要，特编辑工程英语英汉对照词汇表。
目的是为了提供项目常用的中英文对照词汇，方便大家使用，以便更好地实施或服务于本项目。
本此词汇按照工程简介、项目管理部门及岗位名称、工程材料、工程机具、单项别墅项目工序名称、测量工程、钢筋工程、模板工程、混凝土工程、砌筑工程、脚手架工程、装饰工程、给排水通风空调电气工程、质量、环保、消防、文明施工、工程缩略语等15大类进行编纂。
一、工程简介1.阿联酋: united arab emirates, U.A.E.2.棕榈岛,花园别墅项目: PALM JUMEIRAH, GARDEN HOMES VILLAS3.主干,枝叶,圆环挡水岛: trunk, frond, water-retaining crescent4.别墅、公寓: villa, apartment5.世界第八奇迹: the eighth miracle of the world.6.花园别墅类型: types and styles of Garden Home Villas6.1 GARDEN GALLERY: 花园楼座6.2 ATRIUM ENTRY: 中厅入口6.3 CENTRAL ROTUNDA: 中央圆顶6.4 GRAND FOYER: 大前厅6.5 Arabic style: 阿拉伯风格6.6 Mediterranean style: 地中海风格6.7 Moroccan style: 摩洛哥风格6.8 Costa Del Sol style: 哥斯德尔索风格6.9 Santa Fe style: 圣达菲风格6.10 Greek style: 希腊风格7.22种别墅名称说明：7.1 AEAR4：中厅入口, 阿拉伯风格, 4卧室7.2 AEAR4+1F：中厅入口, 阿拉伯风格, 4卧室, 3层7.3 AEAR5：中厅入口, 阿拉伯风格, 5卧室,7.4 AEME4：中厅入口, 地中海风格, 4卧室7.5 AEME4+1F：中厅入口, 地中海风格, 4卧室, 3层7.6 AEME5: 中厅入口, 地中海风格, 5卧室7.7 AESF4: 中厅入口, 圣达菲风格, 4卧室7.8 AESF5: 中厅入口, 圣达菲风格, 5卧室7.9 CRAR4: 中央圆顶, 阿拉伯风格, 4卧室7.10 CRAR5: 中央圆顶, 阿拉伯风格, 5卧室7.11 CRME4: 中央圆顶, 地中海风格, 4卧室7.12 CRME5: 中央圆顶, 地中海风格, 5卧室7.13 CRMO4: 中央圆顶, 摩洛哥风格, 4卧室7.14 CRMO5: 中央圆顶, 摩洛哥风格, 5卧室7.15 GFAR4: 大前厅, 阿拉伯风格, 4卧室7.16 GFAR4+1F: 大前厅, 阿拉伯风格, 4卧室, 3层7.17 GFGR4: 大前厅, 希腊风格, 4卧室7.18 GFME4: 大前厅, 地中海风格, 4卧室7.19 GFME4+1F: 大前厅, 地中海风格, 4卧室, 3层7.20 GGAR3: 花园楼座, 阿拉伯风格, 3卧室7.21 GGME3: 花园楼座, 地中海风格, 3卧室7.22 GGCS3: 花园楼座, 哥斯德尔索风格, 3卧室8.业主: NAKHEEL (纳克希尔)9.监理: SCHUSTER PECHTOLD PARTNERS（SPP）10.设计单位: CRANG & BOAKE INC,(克朗伯克有限公司)11.承包单位: China State Construction Engineering Corporation12.别墅房间布局相关词语12.1 dining room: 吃饭间12.2 kitchen: 厨房12.3 majlis: 客厅12.4 W.C.: 厕所12.5 maid’s room: 女仆间12.6 store: 储藏室12.7 toilet: 厕所12.8 closet: 壁储12.9 garage: 车库12.10 guest bedroom/study: 客卧室间/学习室12.11 shower: 淋浴室12.12 pool: 泳池12.13 master bedroom: 主卧室12.14 services: 服务间12.15 stair/staircase: 楼梯12.16 hall: 大厅12.17 foyer: 前厅12.18 laundry: 洗衣房12.19 balcony: 阳台12.20 lavatory: 洗脸间12.21 bathtub: 浴缸12.22 roof terrace: 屋顶平台12.23 parapet: 女儿墙12.24 linen: 亚麻衣橱12.25 main entrance: 大门12.26 ensuite: 套房12.27 planter: 花盆间12.28 entry porch: 门廊12.29 boundary wall: 围墙12.30 plot limit: 地界12.31 soft landscape: 植草12.32 neighbouring plot: 相邻地块12.33 patio: 院子12.34 ground floor: 一楼12.35 first floor: 二楼12.36 second floor: 三楼12.37 plan: 平面图12.38 elevation: 立面图12.39 details: 详图12.40 section: 断面图12.41 dome: 穹顶二、项目管理部门及岗位名称1 工程管理部: Construction Dept. 2技术部: Technical Dept.3机电部: MEP Dept. 4合约商务部: Contracts and Commercial Dept. 5物资设备部: Materials and Plant Dept. 6财务部: Finance Dept.7 行政部: Administration Dept. 8项目经理:Project Manager (PM)9 项目副经理: Deputy Project Manager 10项目总工程师: Chief Project Engineer11 项目经理助理: Assistant Project Manager12 项目生产助理: Assistant Construction Manager13 技术经理: Technical Manager 14 机电部经理: MEP Manager15合约部经理: Contracts Manager 16 工程部经理: Engineering Manager17 财务经理: Financial Manager 18 行政经理: Administration Manager19 物资设备经理: Materials and Plant Mananger20 采购经理: Procurement Manager 21 采购员: purchaser22 现场工程师: site engineer 23 安全员: safety officer24 测量师: survey engineer 25 计划工程师: planning engineer26 翻译: translator 27 技术协调员: technical coordinator28 施工图设计员: shopdrawing designer 29 试验工程师: testing engineer30 前台秘书:receptionist 31 秘书: secretary32 行政助理: Administration assistant 33 急救员: first aider34 办公室服务员: office boy 35 预算员: quantity surveyor36 钢筋工: steel fixer 37 瓦工: mason38 木工: carpenter 39 机修工: mechanic40 架子工: scaffolder 41 测量员: surveyor42 工人: worker, manpower 43 抹灰工: plasterer44质量工程师:quality engineer 45土建工程师: civil engineer46机电工程师: mechancial/electrical engineer47厨师: chef 48出纳: cashier49医生: doctor 50材料员: material man51 司机: driver 52 公共关系人: public relations officer (PRO) 53 沏茶员: tea boy 54 电工：electrician５５装饰工: decorator 56试验员: testing personnel５７油漆工painter 58估算员; 数量检验员quantity surveyor59 绘图员draftsman 60工头foreman61 小工hodman, hod carrier 62 焊工welder63细木工人joiner 64玻璃工匠glazier65管子工plumber, pipe fitter 66.吊车司机crane driver监理和业主人员名称1. project manager 项目经理2. resident engineer 驻地工程师3. electrical engineer 电气工程师4. mechanincal engineer 暖通工程师5. planning engineer 计划工程师6. senior architect 高级建筑师7. interior architect 室内建筑师8. SPP inspector 监理验收员9. quantity surveyor 预算员10. project coordinator 项目协调员11. 秘书secretary 12. 服务生office boy三、工程材料1 普通硅酸盐水泥: ordinary portland cement (OPC)2 抗硫酸盐水泥: sulphate resisting cement (SRC)3 中等抗硫酸盐水泥: moderate sulphate resisting cement (MSRC)4 “T”高屈服点强度变形钢筋: “T” high yield strength deformed bar5 模板: formwork, form, shuttering6 脚手架: scaffold, scaffolding7 木方: timber8 钢管: steel tube 9 商品混凝土: ready-mixed concrete10 防水材料: waterproofing material( polyethylene sheet, rubberized bitumen)11 纯聚亚安酯: pure polyurethane12 柔性防水膜: flexible waterproofing membrane13 密封剂: sealant 14 刚性绝缘: rigid insulation15 织物过滤器: filter fabric 16 屋面瓦: roof tile paver17 铝质防水板:aluminum flashing 18 copper sheet: 薄铜板19 kerbstone: 路缘石20 backfilling granular: 回填粒状材料21 interlocking concrete paver: 交错砼铺面块22 landscaping: 绿化23 weatherstripping:挡风雨条24 garage door: 车库自动门25 white cement: 白水泥26 lime: 石灰27 sand: 砂子28 G.I. anchor: 镀锌锚片29 hot dipped galvanized steel bar: 热浸镀锌钢筋30 GRP water tank: 玻璃钢水箱31 autoclaved insulated block: 高压蒸养保温砌块32 hollow block: 空心砌块33 solid block: 实心砌块34 GRC: 玻璃丝混凝土35 GRP: 玻璃增强塑料,俗称玻璃钢36 precast lintel: 预制过梁37 polypropylene fiber: 聚丙烯纤维38 paint: 涂料39 plaster board (gypsum): 石膏板40 terracotta tile: 陶瓷砖41 vitreous tile: 铀面瓷砖42 graniti tile: 花岗岩砖43 marble sill: 大理石窗台44 acoustic panel: 吸声板45 ceiling plank: 吊顶厚木板46 fine textured paint to ceiling: 吊顶细纹涂料47 fenomastic paint: 乳香树脂涂料48 emulsion paint: 乳胶漆49 roof access hatch: 屋顶检修口50 plywood: 九夹板51 portal scaffold: 门式脚手52 cuplock scaffold, tube-coupler scaffold: 碗扣式脚手53 tie rod: 对拉螺栓54 channel steel: 槽钢55 toe board: 跳板56 form release agent: 脱模剂57 gunny bag, sack: 麻袋58 safety net: 安全网59 wall tile墙面砖60 floor tile 地面砖61 false ceiling: 吊顶62 mashrabiah:木雕刻63 railing: 栏杆64 UPVC: 未增塑聚氯乙烯65 sanitary wares: 卫生洁具66 waste material: 废料67 nail: 钉子68 terrazzo: 水磨石69 putty: 油灰, 腻子70 batten: 板条71 typical forms: 定型模板72 primary runner channel: 主龙骨73 secondary runner channel: 次龙骨74 fire blanket: 消防毯75 concrete block: 混凝土垫块76 non-slip insert: 防花嵌块77 precast concrete lintel: 预制混凝土过梁78 modified SBS heavy laminate bituminious felt: 改性SBS层压沥青油毡79 polyethylene sheet 1000 gauge: 1000规格聚乙烯防水膜80 light weight concrete: 轻质混凝土81 polystyrene: 聚苯乙烯82 skirting: 踢脚线83 PVC faced acoustic ceiling panels: PVC面吸声吊顶板84 Galvanize steel sheet for duct: 镀锌铁皮风管85 Shock absorber support: 减震支架86 split damper: 分离阻尼器87 flexible connection: 软接头88 Duct acoustic lining: 风管吸声衬里89 Duct insulation material: 风管保温材料90 canvas: 帆布91 sheet Aluminium: 铝板92 refrigerant pipe: 冷却管93 drainage pipe: 排水管94 drainage pipe fittings: 排水管配件95 pipe insulation material: 管道保温材料96 Shut-off valve: 截止阀，断流阀97 filter: 过滤器98 Thermostat: 恒温器[箱, 槽] 99 Sight Glass: 窥镜, 观察孔100 supply air grille: 供气格栅101 return air grille: 回风格栅102 supply air diffuser: 送风风口103 exhaust air diffuser: 排气风口104 return air diffuser: 回风风口105 exhaust air grille: 排气格栅106 L.P.G. chamber: 煤气室107 isolating valve: .隔离阀,关闭塞108 first stage regulator: 一级调节器109 adjustable regulator: 可调调节器110 solenoid valve: 螺线管阀,电磁阀111 gas meter: 煤气表112 Manual shut off valve: 手工断流阀/截止阀113 gas detector: 气体检测器114 electric switch: 电源开关115 flexible hose: 软管116 PE pipe: 聚乙烯管117 gas line 燃气管路118 MUPVC Waste pipe: 改性聚氯乙烯污水管119 Trap for shower: 淋浴室弯管120 floor drain 地面排水管121 Double sink: 双水槽122 gully trap阴沟头123 Manhole: 人孔, 检修孔124 Floor Grating Drain: 格栅地面排水管125 plumbing pipe: 给水管126 PP Cold water plumbing pipe聚丙烯冷水管; 127 stop cock 停止旋塞,止水栓128 Gate valve闸式阀, 闸门阀129 Rubber Insulation橡胶保温130 float valve浮阀131 Check valve: 止回阀132 Cast iron: 铸铁, 锻铁133 House bibs: 室内水龙头134 Aluminum water meter cabinet: 铝水表盒135 vent cock: 放气旋塞［龙头］136 Aluminum Cover: 铝盖137 PVC cable : 聚氯乙烯电缆138 cabinet for Isolators: 绝缘体柜139 Chandelier: 枝形吊灯140 earthing system: 接地系统141 manhole cover: 人孔盖142 steel galvanized conduit: 镀锌铁管143 Video Intercom power outlets: 视频内部通信电源出口144 Water Heater: 热水器145 PVC wire: 聚氯乙烯电线146 conduit: 电管147 cable: 电缆148 outlet: 插座,出口149 MDF: 总配线架, 主配线板150 TV outlet: 电视输出口151 fish wire电缆牵引线甲方供料Client Supply Items1. distribution board配电盘2. ceramic porcelain tiles瓷砖3. A/C equipment 空调设备4. exhaust fan排气扇5. water pump 水泵6. water heater热水器7. marble大理石8. graniti tiles/marble花岗岩砖/大理石9. lighting fixtures灯具10. sanitary fixtures卫生洁具11. balcony balustrade and staircase hand rails阳台栏杆和楼梯扶手12. mirror镜子13. vanity top 梳洗台14. upvc doors and windows: upvc门窗15. bathroom accessories浴室附件16. kitchen cabinet: 菜橱, 碗柜17. water mixer: 搅水器18. wardrobe衣柜, 衣厨19. electric switch电源开关20. timber door木门21. iron mongery: 五金器具22. red roofing tiles: 红色屋面砖四、工程机具Constructional plant1发电机组: generator set 2移动灯: mobile lamp3交通大巴: shuttle bus 4砂浆搅拌机: mortar mixer5强制式搅拌机: forcing mixer 6交流电焊机: AC welding machine7气焊(割)工具: gas welding(cutting) machine8电刨: electric planer 9电锯: electric saw10玻璃钢水罐:GRP water tank 11钢筋切断机: bar cutting machine12钢筋弯曲机: bar bending machine 13卷扬机: hoist14拖拉机: tractor 15机动翻斗车: mobile dumper16汽车吊: truck crane 17全站仪: total station instrument18激光扫平仪: laser swinger 19汽车砼输送泵: mobile concrete pump 20混凝土振动器: concrete vibrator 21叉车: forklift22自卸式翻斗汽车: dump truck 23运水车: water tanker24洒水车: watering truck 25 两头忙(JCB): backhoe loader26装载机: loader 27打夯机(振动式): rammer (vibration type) 28打夯机(平板式): rammer (flatplate type)29压路机: roller 30空压机: air compressor31水罐（带水泵）: water tank (with a pump)32加油车: diesel tanker 33潜水泵: submersible pump34自动温度控制仪: automatic temperature controller35水钻: hydraulic drill 36弯管机: pipe bender37沙轮切割机: abrasive cutting machine 38台钻: bench drill39电锤: electric hammer 40电动试压泵: electric hydraulic test pump 41手动试压泵: manual hydraulic test pump42电动套丝机: electric pipe threading machine43举杆车: telescopic handler 44手推车wheelbarrow45托泥板float 46 铅锤线plumb line47推土机bulldozer 48吊车crane49机械钻power drill 50 平地机grader51 挖掘机excavator 52 压路机roller53 夯土机compactor 54凿子chisel55圆锯circular saw五、项目工序名称Name of process1. substructure: 下部结构、基础2. superstructure: 上部结构3 internal finishing: 内装修 4. external finishing:外装修5. MEP works 机电工程6. blockwork: 砌筑7. plaster 抹灰8. tiles: 贴砖9. ceiling works 吊顶工程10. project commencement项目开工11. phase 1 一期12. phase 2: 二期单项别墅基础工程工序13. blinding concrete 垫层混凝土14. swimming pool structure游泳池结构15. footing-formwork 基础-模板16. footing/column neck –steel reinforcement基础/颈柱-钢筋17. boundary wall foundation围墙基础18. footing concrete: 基础混凝土19. bitumen/curing to foundation: 沥青/基础养护20. ground beam-formwork 地梁-模板21. ground beam-reinforcement地梁-钢筋22. ground beam concrete地梁混凝土23. bitumen-ground beam 地梁刷沥青24. backfill/levelling/compaction 回填/平整/压实25. ground floor slab/stair at entrance 地坪/入口楼梯26. RCC columns-formwork-GF一楼钢筋混凝土柱- 模板27. RCC columns-steel reinforcement-GF一楼钢筋混凝土柱–钢筋28. RCC columns concrete-GF一楼钢筋混凝土柱–混凝土29. RCC beams/slab-formwork/scaffolding-FF 二楼钢筋混凝土梁/板–模板/脚手架30. RCC beams/slab-reinforcement-FF二楼钢筋混凝土梁/板–钢筋31. Staircase internal-formwork 室内楼梯- 模板32. Staircase internal-steel reinforcement室内楼梯–钢筋33. RCC beams/slab/staircase-concrete pouring-FF二楼钢筋混凝土梁/板/楼梯–浇筑混凝土34. RCC columns-formwork-FF二楼钢筋混凝土柱–模板35. RCC columns-reinforcement-FF二楼钢筋混凝土柱–钢筋36. RCC columns-concrete-FF二楼钢筋混凝土柱–混凝土37. beams/slab-formwork-SF三楼梁/板–模板38. beams/slab-steel reinforcement-2nd FL三楼梁/板-钢筋39. beams/slab-concrete pouring-2nd FL 三楼梁/板-浇筑混凝土40. RCC columns-roof floor 屋顶钢筋混凝土柱41. RCC beams/slab –formwork-roof floor屋顶钢筋混凝土梁/板-模板42. RCC beams/slab –steel reinforcement-roof floor屋顶钢筋混凝土梁/板-钢筋43. decorative arches in elevation装饰拱44. RCC beams/slab –concrete pouring-roof floor屋顶钢筋混凝土梁/板-浇筑混凝土45. upstand/parapet立柱/女儿墙单项别墅机电工程工序46. drainage upvc sleeves in concrete 混凝土中upvc排水套管47.water supply upvc sleeves in concrete混凝土中upvc给水套管48. electrical system holes, trenches and ducts in concrete 混凝土中电气系统的孔洞、沟槽和导管49. electrical pvc pipe, junction, switch and socket box：pvc电管、接线盒、配电箱、插座50. installation of roof drain inlet, balcony drain SL屋面排水口、阳台排水口的安装？51. duct installation 风管安装52. lighting system wiring 照明系统配线53. pipe/cable tray installation 管道/电缆托架安装54. low current-LV system wiring 弱电系统配线55.junction, switch and socket box接线盒、配电箱、插座56.cabinet (panel) SMDB/DB/FDB installation总配电箱\分配电箱\小配电箱安装57. PEX pipe installation with fittings: PEX给水管及配件安装58. LPGS pvc sleeve pipe in wall墙中液化石油气pvc套管59. cable installation 电缆安装60. electrical meter box installation 电器仪表箱安装61. installation of telephone MDF, LCJB, socket电话主配线板、分线箱、插座安装62. installation of duct flexible connectors风管软接头安装63. A/C electrical tube and cable installation空调电管和电缆安装64. installation of audio visual system 视频、音频系统安装65. cabinet, speaker, KP, control cable电柜、扬声器、KP、控制电缆66. installation of floor drain cover, grating地面排水管盖子和格栅的安装67. LPGS valve chamber液化石油气阀室68. CCTV system rack, monitor, camera installation闭路电视系统架子、监视器和摄像机的安装69. installation of fan coil units风机盘管安装70. LPGS meter boxes液化石油气仪表箱71. testing and commissioning检测和调试72. installation of water pump in water plant room自来水厂水泵的安装73. installation of exhaust fan排气扇的安装74. video intercom system equipment, handset wiring视频内部通信系统设备和电话机的配线75. telephone and data system testing and commissioning 电话和数据系统测试和调试76. LPGS equipment installation液化石油气设备安装77. water heater installation热水器安装78. installation of grills, diffusers, louvers and damper格栅、风口、遮光栅格、格栅阀的安装79. video intercom system testing and commissioning 视频内部通信系统测试和调试80. LPGS detector and switch液化石油气检测器和开关81. A/C thermostat installation空调恒温器安装82. lighting equipment and light fixtures installation照明设备和灯具安装83. LPGS testing and commissioning液化石油气检测和调试84. installation of sanitary fixtures and water mixers卫生洁具和搅水器的安装85. installation of fire extinguishers灭火器的安装86. door bell installation门铃安装87. testing and commissioning-W/S system防水系统的测试和安装？88. testing and commissioning-power and lighting system电力和照明系统的测试和调试89. fire blanket installation消防毯安装90. portable fire extinguishers便携式灭火器91. A/C equipment base空调设备基础92. installation of A/C duct split unit风管分离装置的安装93. A/C-testing and commissioning空调的测试和调试94. electrical and mechanical testing and commissioning机电测试和调试单项别墅内装修工序95. hollow/solid/thermal block空心／实心／保温砌块96. precast lintels预制过梁97. internal plaster for concrete soffit室内混凝土底面抹灰98. blockwork-boundary wall围墙砌筑99. internal wall plaster with preparation室内墙壁抹灰及制备100 boundary wall columns and coping围墙柱子和墙帽101 plaster to boundary wall围墙抹灰102 wall tile with preparation墙砖及准备103 external plaster preparation室外抹灰准备104 water proofing wet areas潮湿部位防水105 floor tiles with preparation地板砖及准备106 external plaster室外抹灰107 marble slab-20mm大理石板－２０mm108 marble-skirting大理石踢脚线109 marble sills for windows大理石窗台110 marble steps for internal stairs室内楼梯大理石台阶111 terracotta tile陶瓷砖112 gypsum plaster board/gypsum tiles/bulkhead/PVC/MDF石膏板／石膏砖／隔板／PVC ／中密度板113 terracotta skirting陶瓷踢脚线114 terracotta tile for external steps室外台阶陶瓷砖115 threshold门槛116 counter top/vanity top柜台／梳洗台117 typical railings to staircase and terrace楼梯和平台的标准栏杆118 light weight foam concrete轻质泡沫混凝土119internal paint for ceiling室内吊顶刷涂料120 UPVC exterior doors and windows室外UPVC门窗121 washroom accessories盥洗室附件122 internal paint to gypsum board ceiling室内石膏板吊顶刷涂料123 mirrors with polished aluminum frames抛光铝框镜子124 roof water proofing屋面防水125 internal paint for plastered wall室内抹灰墙面刷涂料126 railing to rotunda圆顶栏杆127 door for electrical room配电房的门128 water mixer混合器129 roof tile pavers/roofing works屋面砖／屋面工程130 fixing of kitchen cabinets厨柜的安装131 wooden doors internal 室内木门132 roof access hatch and ladder/GRP ladder for water tank屋面检查孔和梯子／水箱的玻璃钢梯子133 clay tiles陶砖134 fixing of wardrobes壁橱的安装135 wooden gates-front and seaside正面和海边的木门136 marshrabiah/timber fencing木雕刻／木围墙单项别墅外装修和室外工程工序137 GRC works around windows窗子周围的玻璃（纤维）增强混凝土138 GRC works around doors门周围的玻璃（纤维）增强混凝土139 compacted granular fill/soft landscaping压实的粒状填料／软绿化140 hardscaping硬质景观141swimming pool finishes游泳池装修142 external paint for exterior elevation外墙立面刷涂料143 paint to boundary wall围墙刷涂料144 kerbs and kerbstones路缘石145 interlock concrete pavers嵌锁混凝土铺面块146 snagging and final inspection清除困难和最终验收147 demobilization and handing over撤场和移交148 mobilization: 施工准备、动员149 project duration项目工期150 cash flow现金流量151 critical path专键路径152 milestone 里程碑153 critical acitivity 专键作业六、测量工程survey work１．现场site, jobsite ２．控制点control point (station)３．坐标coordinates 4. 高程level, elevation5. 平面坐标plane coordinates6. 全站仪total station instrument7. 夹角angle 8. 误差error9. 允许误差permissible tolerances 10. 水准仪spirit level11. 往返测量to-and-from survey 12. 闭合差misclosure13. 现场控制网Site Control Grid14.现场控制点加密Addition of site control points15. 轴线axis 16. 角点corner points17. 围墙边界fence wall boundary 18 地块边界plot limit19. 定位positioning 20. 边长border length21. 一级控制网first control grid 22. 极坐标法method of polar coordinates23. 闭合closure 24. 附合测法method of connecting level survey 25. 施工测量Construction Survey 26. 控制线control line27. 位置线position lines 28. 轴线投测transfer survey of axes29. 标高抄测level survey 30. 水平线level line31. 弹线draw a line 32. 基准点datum point33. 平均标高mean elevation (level) 34. 引测transfer survey35. 平行借线法method of parallel line transfer36. 沉降观测Observation and Measurement of Settlement37. 验线Verification of Lines 38. 测量员surveyor39. 经纬仪theodolite 40. 钢尺steel rule41. 塔尺leveling pole七、钢筋工程REINFORCEMENT1. 变形钢筋deformed bar2. 特征强度characteristic strength3. 规格和型号specs and type4. 出厂质量证明书mill certificate5. 试验报告单test report6. 切割和弯曲cut and bend7. 钢筋检验test of reinforcement 8. 性能复试performance.retest9. 试验样品test specimen (sample) 10. 钢筋保护层Rebar Cover11. 砼的腐蚀corrosion of concrete 12. 钢筋锈蚀rusting of reinforcing steel13. 密实性compactibility 14. 细石砼垫块fine stone concrete block15. 钢筋的连接rebar joining 16. 钢筋搭接rebar splicing17. 纵筋longitudinal reinforcement 18. 搭接长度splice length19. 光圆钢筋plain round bar 20. 钢筋加工rebar processing21. 化学成分试验chemical (composition) analysis22. 构件element 23. 跨度span24. 截面cross section 25. 排放图rebar shopdrawing26. 配料单cutting list 27. 钢筋下料cut and bend28. 钢筋上挂牌label on rebar29. 加工、存放、运输、绑扎process, storage, transport and binding of rebar.30. 铁锈iron rust 31. 油渍oil stain32. 无损伤free of damage 33. 钢筋绑扎rebar placement34. 铁丝iron wire 35. 八字扣8 character-like buckle36. 箍筋stirrup, link 36. 弯钩hook37. 基础钢筋Foundation Rebar 38. 工艺流程process flow39. 柱子插筋column starter，starter bar 40. 钢筋网bar mesh41. 柱钢筋Column Bar 42. 主筋main reinforcement43 柱外皮尺寸线outer dimension lines of column44. 箍筋间距stirrup spacing 45. 缠扣绑扎tangled buckle46. 梁钢筋reinforcement of Beam47. 连续梁、悬臂梁、简支梁continuous beam, cantilever beam, simply-supported beam48. 上部纵筋top main reinforcements 49. 楼板钢筋slab reinforcement50. 钢筋马凳chair bar 51. 楼梯钢筋staircase reinforcement52. 分布筋distribution bar 53. 踏步筋step bar54. 末端锚固end anchorage55. 缺扣、松扣absent buckles or loose buckles56. 成品保护protection of finished product 57. 钢筋调整adjustment of bar58. 预留钢筋reserved bars59. 自检、互检、交接检self-check, mutual check and cross check60. 绳卡rope clip 61. 钢筋绑扎rebar placement62 主筋main reinforcement, principal reinforcement63 上部和下部钢筋top and bottom reinforcement64 钢丝wire fabric 65 定位钢筋spacer bar66 点焊tack welding 67 弯曲试验bend test68 环氧涂层epoxy coating 69 cutting list, bar bending schedule下料单八、模板工程formwork, shuttering1. 模板配置allocation of formwork2. 定型模板typical formwork3. 支架supporting structure4. 稳定性stability5. 18mm厚多层双面覆膜胶合板18mm double-face glued plywood6. 木方timber7. 水平背楞horizontal beam8. 钢管steel tube 9. 对拉螺栓tie rod (bolt)10. 圆形柱和异形柱circular and irregular columns11. 矩形柱及方形柱rectangular and square columns12. 竖龙骨vertical beam 13定型侧帮模，挡板模typical side form, baffle form 14. 柱模板column formwork 15. 定位钢筋positioning rebar16. 木方柱箍timber hoop 17. 钢筋环rebar ring18. 柱头模板formwork of column head 19. 模板拆除formwork removal(striking) 20. 钢柱箍steel hoop 21. 临时孔temporary hole22. 顶模、底模与侧模top form, bottom form and side form23. 木方斜撑timber prop 24. 塑料套管plastic sleeve25. 起拱高度cambered amount 26. 水平拉杆horizontal tie bar27. 拆除模板的时间removal time 28. 拆模顺序removal sequence29. 支撑prop 30. 脱模剂form release agent31. 板面平整度surface evenness of forms32. 强度，刚度和稳定性strength, rigidity and stability33. 接缝严密tight joint 34. 漏浆leakage of mortar35. 垂直度plumbness 36. 公差tolerance37. 临时支撑temporary shoring 38. 交叉作业intersecting operations39. 楔子wedge九、混凝土工程concrete work1. 商品砼ready-mixed concrete2. 砼浇注concrete pouring3. 砼搅拌站batching plant4. 砼标号concrete grade5. 钢筋砼结构reinforced concrete structure(RCC structure)6. 水泥含量cement content7. 水灰比water to cement ratio (W/C raito)8. 胶结材料cementitious material9. 磨细矿渣ground granulated blastfurnace slag (GGBS)10. 普通硅酸盐水泥ordinary Portland cement (OPC)11. 抗硫酸盐水泥sulphate resisting Portland cement (SRC)12. 中等抗硫酸盐水泥moderate sulphate resisting Portland cement (MSRC)13. 硅粉Micriosilica ( “MS”) 14. 断级配集料Gap-graded aggregate 15. 单一尺寸集料Single-size aggregate 16. 目标平均强度target mean strength 17. 全集料“all-in” aggregate 18. 矿渣slag, blastfurnace slag19. 级配石子graded stone 20. 细骨料fine aggregate21. 干净砂clean sand 22. 含盐量salt content23. 粗骨料coarse aggregate 24. 砼配合比设计concrete mix design 25. 砼试块concrete test cube 26. 试配trial mix27. 掺合料admixture 28. 试验结果test result (report)29. 电脑打印单computer printout 30. 稠度consistency31. 进料单delivery ticket32. 砼罐车和汽车泵truck mixer (transit mixer) and concrete pump33. 砼浇注计划concreting plan34. 浇筑区域和浇注的连续时间bay number and the succession of concreting35. 砼凝结concrete setting 36. 浇注地点area of pouring (placement) 37. 浇注间隙pouring break 38. 施工缝construction joint39. 终凝final setting 40. 养护curing41. 插入式振捣器internal (immersion) vibrator42. 管槽或滑槽trunking or chutes 43. 砼离析segregation.44. 砼振捣Concrete Vibration 45. 砼初凝initial setting46. 垂直振捣vertical vibration 47. 斜向振捣inclined (slanting) vibration 48. 气泡air bubble 49. 拉通线draw a straight line50. 抹平搓实finishing 51. 麻袋sack52. 坍落度slump 53. 抗压强度compressive strength54. 凝固后的密度hardened density 55. 渗水性water permeability56. 快速氯化物渗透rapid chloride penetration (RCP)57. 泌水性Bleeding 58. 氯化物Chloride (CI)59. 硫酸盐Sulphate 60. 轻质混凝土light weight concrete61. 硬化剂和密封料hardener and sealer 62. 止水带waterstop63. 填缝料joint filler 64. 隔粘剂bond breaker65. 不收缩灰浆Nonshrink Grout 66. 腐蚀抑制剂corrosion Inhibitor admixture 67. 配料单Batch Ticket 68. 砼坍落度Concrete Slump69. 对集料的视检查（洗后）Visual Examination of Aggregates (after washing)70.混凝土密度和抗压强度Concrete density and compressive strength71硫酸盐和氯化物含量SO3 and Cl contents72常规的混凝土取芯样Concrete Coring73混凝土进场concrete delivery 74不合格混凝土non-compliant concrete75水泥浆grout 76有缺陷的混凝土defective concrete77水泥沟缝cement pointing 78 取样率sampling rate (frequency)79 热养护heat cured 80 新浇混凝土fresh concrete81 减水剂water reducing admixture 82 加气剂air-entraining admixture83 高效增塑剂superplasticizing admixture 84 配料员batcherman85 袋装水泥bag cement 86 地磅weighbridge87 维比稠度vebe degree 88 随机取样random sample89. 素混凝土plain concrete 90砂浆棒mortar bar91 浇筑层lift 92 伸缩缝expansion joint93 工厂试验plant trial 94 实验室试验laboratory trial95 float，trowel抹子、镘刀96 hardener 硬化剂97 non-compliant concrete 不合格混凝土98 defective concrete 有缺陷的混凝土十、砌筑工程BLOCKWORK1. 砼砌块concrete block2. 迪拜市政府批准的证书Dubai Municipality approved certificate3. 加筋件stiffener4. 水平灰缝和竖向灰缝bed joint and perpend joint5. 砂浆饱满度mortar satiation degree6. 镀锌锚片G.I. anchor7. 热浸镀锌钢筋hot dipped galvanized steel bar8. 镀锌扁钢、墙体连接件和水平墙钢筋Galvanized flat bar, wall tie and horizontal wall reinforcement9. 砂浆层mortar course 10. 空心砼砌块hollow concrete block11. 实心砼砌块solid concrete block 12. 允许偏差Permissible tolerance13. 水平槽或斜槽horizontal or inclined groove14. 砌筑masonr 15. 砌筑钢筋masonry reinforcement16. 进场和储存delivery and storage17. 高压蒸养标准砖autoclave modular Blocks18. 线性收缩linear shrinkage 19. 湿涨缩moisture movement20. 水硬性石灰hydrated lime 21. 砂浆配合比mortar mix22. 石灰水泥砂浆cement lime mortar23. 高压蒸养加气混凝土砌块Autoclaved Aerated Concrete Block24. 轻质隔墙Light Partition Wall 25. 干密度Dry Density26. 垫层砂浆Bed Mortar 27. 粘结剂Binder:28. 塑化剂、粘性提高剂、保水剂Plasticizing agent, adhesion promoting agent, Water retaining agents29. 砌筑接缝masonry joint30. 垂直接缝和水平接缝Vertical and horizontal joints31. 控制缝control joint 32. 潜入、预埋embedment33 勾缝和填缝jointing and pointing 34 砌筑砌块laying blocks35 顺砖砌筑stretcher 36 凹槽砖frog brick37 清水墙fair-faced masonry 38 伸缩缝movement joint39 嵌缝材料caulking material十一、脚手架工程SCAFFOLDING, FALSEWORK1. 外脚手架exterior scaffolds (scaffolding)2. 双排脚手架double-row scaffolding3. 标准型门架Standard portal frame4. 立杆standard5. 脚手架配件scaffold fittings6. 横杆ledger, horizontal lacing tube7. 斜撑杆diagonal bracing tube 8. 脚手板toe board9. 马道catwalk 10. 剪刀撑Cross bracing11. 填充梁(次楞) infill beam (secondary beam) 12. 主梁(楞) primary beam13. U托: U bracket 14 底座base Jack15. 管接头sleeve coupler 16. 底板baseplate十二、装修工程FINISHING WORK1. 精装修fine finishing2. 粗装修coarse finishing3. 各专业trades4. 十字中心线cross centerline5. 墙面饰面, 地面饰面wall finishing, floor finishing6. 五金配件finish hardware7. 机电安装MEP installations8. 地面防水floor waterproofing 9. 墙面瓷砖wall tiles10. 顶棚龙骨runner channels on the ceiling 11. 地面砖floor tiles12卫生洁具sanitary wares 13. 电气安装electrical installation14 盥洗台vanity top 15. 天棚吊顶安装installation of false ceiling 16. 墙面抹灰Plastering on the Walls 17. 基层base course18. 房间规方squaring room 19. 标准灰饼standard spacer block20. 底层抹灰,中层抹灰,面层抹灰plastering base course, undercoat and topcoat21. 简易门式脚手架Simple portal scaffolding 22. 内墙抹灰internal plastering23. 金属网wire netting 24. 阴阳角inside and outside corners25. 分格缝grid seams 26. 吊顶工程Ceiling Work27. 大龙骨吊杆hangers for main runner channel28. 大龙骨main runner channel29. 中、小龙骨medium and small runner channels30. 安装罩面板install ceiling panels31. 铝格和隐藏式木板吊顶aluminum grid and recessed board ceiling32. 石膏板吊顶gypsum board ceiling 33. 膨胀螺栓expansion bolts34. 吊点hanging points 35. 吊筋hanging bar36. 照明、通风、消防等专业such trades as lighting, ventilation and fire fighting37. 预留孔洞reserved openings 38. 自攻螺钉self-drilling screws39. 专用胶带及腻子special adhesive tape and putty40. 厕所、洗衣房、洗涤间、厨房toilets, laundries, washrooms and kitchens41. 瓷砖墙裙ceramic tile skirting 42. 防水涂料waterproofing paint43. 釉面砖vitreous tiles 44. 底子灰priming putty45. 纵横皮数quantities of horizontal and transverse tiles46. 瓷砖预排pre-arrangement of the tiles 47. 楼地面工程Flooring48. 交错砖地面interlocked tile flooring 49. 大理石地面marble flooring50 水泥沙浆cement mortar 51 涂料Paint52 相对湿度relative humidity 53表面麻面pockmarked face, pitting54样板间mockup 55 耐水性的腻子water-resistant putty56 流坠drop 57. 溶剂型涂料solvent paint58. 粘度或稠度viscosity or consistency 59. 防水封闭层Waterproofing enclosure course 60 防火resistance to fire 61 防潮resistance to damp penetration62 防潮层damp proof course 63 表面缺陷surface blemish64. 隐蔽工程验收concealment inspection 65 滚铺法roller pavement method66. 冲筋、刮杠、砂浆找平层：screed 67 防火门fire rated door68. 底层油漆、内层油漆和面漆prime coat, undercoat and topcoat69. 施作人员：applicator 70. 压力喷浆gunite71 木制品millwork 72 辅助框架subframe73 框缘architrave十三、给排水工程、通风空调工程、电气工程PLUMBING AND DRAINAGE, VENTILATION AND AIR CONDITIONING, ELECTRICAL WORKS1 质量保证文件warranty 2阀件Valve3 耐压试验、试压pressure test4 主干管main pipeline5 立管standpipe, riser pipe, vertical pipe6 排水管drain pipe7 吊架或托架hanger frame or bracket 8 给水系统plumbing system9 隐蔽hide, conceal10 贯通水试验water run-through test, penetration test11 通球试验Ball test 12防腐anti-corrosion, antisepsis13 除锈derusting 14电线管、盒electrical conduit and box15预埋件embedded item, embedding 16预留洞reserved opening17配电箱distribution box 18照明系统Lighting system。
结构专业常用英语词汇
结构专业常⽤英语词汇结构专业常⽤英语词汇1. ⼀般术语房屋建筑⼯程building engineering ⼟⽊⼯程civil engineering 建构筑物construction works 结构structure基础foundation地基ground; foundation soils ⽊结构timber structure 砌体结构masonry structure 钢结构steel structure 混凝⼟结构concrete structure 特种结构special engineering structure房屋建筑building⼯业建筑industrial building 民⽤建筑civil building⽔⼯建筑物marine structure 剪⼒墙结构shear wall structure 混合结构mixed structure 板柱结构slab-column system 框架结构frame structure 壳结构shell structure 拱结构arch strucuture桁架结构truss⽹架结构space grid structure 悬索结构cable-suspended structure 框架-剪⼒墙结构frame-shear wallstructure筒体结构tube structure ⾼耸结构high-rise structure 斜拉桥cable stayed bridge 悬索桥suspension bridge 桁架桥trussed bridge 拱桥arch bridge 引桥approach span 桥墩pier 隧道tunnel 混凝⼟坝concrete dam 渠道channel2. 结构构件构件member 部件component; assembly parts 梁beam截⾯section 板slab; plate 柱column 墙wall 壳shell 桁架truss框架frame刚架rigid frame排架bent frame简⽀梁 simply supported beam 悬臂梁cantilever beam 连续梁continuous beam 叠合梁superposed beam 伸缩缝expansion and contraction joint 截⽔沟(天沟)catch ditch;intercepting channel 排⽔沟 drainage ditch 护坡slope protection;revetment 挡⼟墙retaining wall ⽌⽔sealing; seal;节点joint 桩pile沉降缝settlement joint 防震缝aseismic joint施⼯缝construction joint基础梁foundation beam桩承台pile cap; bearing platform底板 bottom slab⽔池顶板basin top slab现浇墙板cast-in-place wall panel预制墙板pre-cast wall panel钢筋混凝⼟框架reinforced concreteframe钢筋混凝⼟柱reinforced concretecolumn先张法预应⼒混凝⼟管桩pretensioned spunconcrete piles钢筋混凝⼟现浇板cast-in-placereinforced concreteslab斜梁 stringer平台梁 beams of platform⼥⼉墙 parapet⼈孔盖板 manhole cover集⽔坑catchment pit溢流槽 flood relief channel 爬梯 ladder⽜腿 bracket仪表槽盒⽀架instrument trench support电缆⽀架cable trench support ⽀撑brace⽀架support3. 结构材料预埋件embedded plate钢板steel plate钢圆环 steel ring plate⾬⽔篦⼦板 rain water grating 钢筋reinforcing bar I 级 grade I热轧光圆钢筋hot rolled plainsteel bars热轧带肋钢筋hot rolled ribbedsteel bars插筋anchor rebar钢筋锚固长度bond length of rebars钢筋搭接bar splicing箍筋stirrup纵向钢筋longitudinal bar弯起钢筋bent-up bar钢筋间距rod spacing;bar spacing搭接长度overlapping length胀锚螺栓 expansion bolts螺母nut锚栓anchor bolt地脚螺栓foundation boltM30六⾓螺帽M30 six angle screw cap外露100，丝扣80outcrop 100mm，thread 80mm 垫⽚ washer C40混凝⼟C40 concrete: class 40早强剂early-strength admixture细⽯混凝⼟fine aggregate concrete防冻附加剂antifreeze admixture配合⽐mixture ratio抗渗等级P8 seepage class:抗压强度compression strength混凝⼟保护层厚度minimum concrete cover普通硅酸盐⽔泥ordinary portland cement 砂sand卵⽯pebble碎⽯crushed stone砾⽯gravel⾻料aggregate⽔泥cement粘⼟砖clay brick 垫层cushion4. 地基基础扩展基础spread foundation地基ground,foundation soils 刚性基础rigid foundation 独⽴基础single footing 联合基础combined footing 条形基础strip founcation 壳体基础shell foundation 箱形基础box foundation 筏形基础raft foundation 桩基础pile foundation沉井基础open caisson foundation ⼤直径桩基础cylinder pile foundation ⼟岩组合地基soil-rock composite ground地基允许变形值allowable subsoil deformation地基处理ground treatment 复合地基composite foundation 强夯dynamic compaction ⽀档结构retaining structure 基坑⼯程excavation engineering ⾼应变动⼒检测high strain dynamic testing of piles 单桩竖向抗压静载试验vertical compression bearing capacity static test for single pile 单桩⽔平静载试验lateral bearing capacitystatic test for single pile 单桩竖向抗拔静载试验vertical up-lifting bearing capacitystatic test for single pile 单桩竖向抗压极限承载⼒vertical ultimatecompress bearing capacity of a singlepile 桩侧摩阻⼒skin friction resistance 桩顶⽔平位移lateral displacement 桩端阻⼒end bearing resistance 单桩静载试验static test of single pile 单桩⽔平极限承载⼒ultimate lateral bearing capacity for a single pile 单桩竖向抗拔极限承载⼒ultimate vertical up-lifting bearing capacityfor a single pile 素填⼟ Plain Fill 粉⼟ Silt 粉质粘⼟ Silty Clay 淤泥质粉质粘⼟Sludgy Silty Clay 粉砂Silty Sand ⾼压缩性 high compressibility 中粗砂medium sand 中等压缩性 medium compressibility 中细砂fine sand 低压缩性 low compressibility 可塑~硬塑状态 plastic-hard plastic 泥质粉砂岩 Muddy Silty stone 流塑状态 flow plastic 粉砂质泥岩 Silty mudstone 局部软塑状态 partly soft plastic 泥岩 Mudstone 饱和saturated 强风化 high weathered 松散incompact 中等风化 medium weathered 轻微裂缝 slight defective pile 断桩 breakage of pile 桩⾝完整 pile of body integrity 缩颈 pile diameter reduction 缺陷 defect 压缩系数coefficient of compressibility 渗流seepage flow 内聚⼒（粘聚⼒） cohesion5. 钢结构钢结构 steel structure底漆 paint primer涂层 coating中间漆intermediate painting 油漆，涂料 paint⾯漆 finish coat流坠 hanging透底 disclosure皱⽪ wrinkle漏涂 miss painting返锈 rust again漆膜厚度 film thickness结构构件 structural member垂直⽀撑vertical bracing桁架 truss⼩⽴柱 postWA325钢格栅板 WA325 grating斜梁 stringer踏步板 treads钢梯 steel stairway踏步钢格板 grating for stair tread斜梯栏杆 guard rails不锈钢栏杆 stainless steel handrail预制场地 prefabrication area 平台栏杆 GR of platform原材料 raw material半成品 semi-finished goods除锈 remove rust, cleaning 切割 cutting喷砂 sand blasting打磨坡⼝ grinding型钢 section steel热轧⼯字钢hot-rolled I-beam steel热轧钢板 hot-rolled plates热轧不等边⾓钢hot-rolled unequal-legangle steel热轧等边⾓钢hot-rolled equal-legangle steel热轧H型钢hot-rolled H steel热轧槽钢hot-rolled channel steel ⽆缝钢管 seamless steel pipes扁钢 strap steel 不锈钢板 stainless steel plate垂直度 verticality分⽚组装be assembled by sections现场成框 framed at site焊缝 weld seam V型坡⼝V-type bevel焊缝⾼度 weld height焊枪 welding gun焊缝长度 weld length焊机 welding machine⽓焊 gas welding 焊炬 welding torch电焊 electric welding ⾃动和半⾃动电弧焊automatic andsemi-automatic welding ⼿⼯焊 hand welding对焊 butt welding 焊条weld rod, electrode ⾓焊缝 fillet 间断焊接 gap welding 咬边 undercut 针孔 pinhole 夹渣 slag裂纹 crack烧穿 burning out 漏焊 losing welding 弧坑 concavity 未焊透lack of fusion 打磨 grind⽕焰切割 torch cutting 喷砂除锈The sand blasting 机械钻孔drill by machine预拉⼒ prestressed ⾼强度⼤六⾓头螺栓Set of big hexagonalhigh-strength bolt 抗滑移系数Slide coefficient of faying surface 扭矩系数torsional moment coefficient终拧扭矩final torsional moment6. 荷载、强度、可靠度剪⼒shear 剪切变形shear deformation压⼒pressure 延伸率percentage of elongation 剪切模量shear modulus 拉⼒tension 应⼒stress 应变strain应⼒集中concentration of stress 应⼒松弛stress relaxation 应⼒图stress diagram 应⼒状态state of stress位移 displacement 弹性变形 elastic deformation 变形 deformation 塑性变形 plastic deformation 应变 strain 剪应变 shear strain 线应变 linear strain 主应变 principal strain 轴向⼒ normal force 主应⼒ principal stress 正应⼒ normal stress 预应⼒prestress应⼒应变曲线stress-strain curve 裂缝crack抗压强度compressive strength 抗弯强度bending strength 抗扭强度torsional strength 抗拉强度tensile strength 屈服yield屈服点yield point屈服荷载yield load 屈服极限limit of yielding 屈服强度yield strength 屈服强度下限lower limit of yield 荷载load横截⾯section, cross 承载⼒bearing capacity 承重结构bearing structure 弹性模量elastic modulus 塑性plasticity延性ductileity受弯构件member in bending轴向拉⼒axial tension受拉区tensile region可靠性reliability受压区compressive region粘结⼒cohesive force配筋率reinforcement ratio偏⼼受拉eccentric tension配箍率stirrup ratio偏⼼受压eccentric compression泊松⽐Poisson’s ratio偏⼼距eccentric distance跨度span疲劳强度fatigue strength跨⾼⽐span-to-depth ratio偏⼼荷载eccentric load设计限值 limiting design value截⾯宽度 breadth of section截⾯⾼度 height of section截⾯厚度 thickness of section截⾯直径 diameter of section截⾯⾯积 area of section截⾯周长 perimeter of section截⾯模量（抵抗矩） section modulus截⾯惯性矩 second moment of area截⾯极惯性矩polar second moment of area 截⾯回转半径 radius of gyration长细⽐slenderness ratio偏⼼矩 eccentricity偏⼼率 relative ecdentricity振动 vibration⾃振频率 natural frequency加速度 acceleration振周期natural period of vibration 频率 frequency振幅 amplitude of vibration⾃由度 degree of freedom振型 mode of vibration阻尼 damp共振 resonance强迫振动 forced vibration设计荷载design load挠度deflection设计强度design strength构造construction脆性破坏brittle failure延性破坏ductile failure可靠性 reliability适⽤性 serviceability安全性 safety耐久性 durability设计基准期 design reference period可靠概率 probability of survival可靠指标 reliability index失效概率 probability of failure概率设计法 probabilistic method极限状态设计法 limit states method容许应⼒设计法 permissible stressesmethod正常使⽤极限状态serviceability limitstates承载能⼒极限状态 ultimate limit states极限状态 limit states分项系数 partial safety factor体分布⼒ force per unit volume 作⽤ action⼒矩 moment of force线分布⼒ force per unit length永久作⽤ permanent action⾯分布⼒ force per unit area可变作⽤ variable action偶然作⽤ accidental action静态作⽤ static action固定作⽤ fixed adtion动态作⽤ dynamic action⾃重 self weight温度作⽤ temperature action施⼯荷载 site load地震作⽤ earthquake action⼟压⼒ earth pressure⽔压⼒ water pressure风荷载 wind load雪荷载 snow load风振 wind vibration吊车荷载crane load屋⾯活荷载floor live load浮⼒ buoyance浪压⼒（波浪⼒） wave pressure泥沙压⼒ silt pressute冰压⼒ ice pressure冻胀⼒ frost heave force静⽔压强 hydro-static pressure静⽔总压⼒total hydro-static pressure 动⽔压强 hydro-dynamic pressure压⼒⽔头 pressure head作⽤代表值 representative valueof an action作⽤准永久值quasi-permanent valueof an action作⽤标准值 characteristic valueof an action作⽤组合值combination value ofactions作⽤设计值 design value of anaction作⽤效应 effects of actions作⽤组合值系数coeffcient forcombination value ofactions作⽤效应系数coefficient of effectsof actions作⽤效应基本组合 fundamentalcombination foraction effects短期效应组合combination for short-term action effects作⽤效应偶然组合 accidentalcombination foraction effects长期效应组合combination for long-term action effects轴线axes标⾼elevation; datum mark坐标coordinate基准点，标⾼datum mark中⼼标⾼center elevation绝对标⾼absolute elevation相对标⾼relative elevation平⾯控制plane control⾼程控制elevation control⽔准点bench mark经纬仪transit坐标控制点coordinate control points ⽔准仪surveyor level测杆surveying rod 钢卷尺steel tape测距仪range finder7. ⼟建施⼯挖掘 excavate履带式推⼟机crawler dozer挖⼟机 excavator履带式起重机crawler crane反铲挖⼟机 back digger压路机 road roller挖沟机 trench digger翻⽃车 tipping skip铲运机 scraper⾃卸卡车 dumping truck洒⽔车 sprinkler回填 back fill⼟⽅⼯程 earth work蛙式打夯机 frog rammer钢筋切断机 bar cutter钢筋弯曲机 angle--bender基坑foundation pit双排竖管脚⼿架independent scaffold脚⼿架scaffold管⼦脚⼿架pipe scaffold 单排竖管脚⼿架putlog scaffold 满堂脚⼿架full framing ⽴杆 the standing pole 扫地杆 ground bars 横杆 ledger脚⼿板 scaffold board 防护栏 protective barrier,guard rail隔离剂 isolating agent扣件coupler旋转扣件swivel coupler ⼗字扣件double coupler 套筒扣件sleeve coupler 钢筋加⼯ rebar fabrication 铁丝 iron wire 钢筋连接rebar connection 绑扎lashing 搭接lap焊接 welding搭接接头 lap joint 焊接接头 welded joint 搭接焊lap welding 砂浆垫块mortar block制模，模板⼯程formwork 组合钢模板 combined steel formwork 模板form模板配板 formwork configuration 模板⽀设 formwork erection 安装偏差 installation deviation 模板接缝the formwork joint泵送混凝⼟pumping of concrete 混凝⼟中⼼搅拌站 centralized concretemixing plant 浇灌混凝⼟concrete pouring, depositing concrete,模板拆除 formwork removal 混凝⼟搅拌汽车concrete mixer truck混凝⼟搅拌concrete agitation 插⼊式振捣器 insertion type vibrator 振捣混凝⼟ vibrated concrete 平板振动器 plate vibrator 抹⼦，泥⼑ trowel 抹灰，抹光 toweling坍落度slump两组试块two sets of testing blocks 混凝⼟取样witness sampling of concrete混凝⼟施⼯缝处理treatment of concrete construction joint 初凝 initial set 终凝final set初凝时间 initial setting time 终凝时间final setting time 混凝⼟养护concrete curing 草垫 straw mattress回填back fill回填夯实backfill consolidation 1:2⽔泥砂浆20厚1:2 cenment mortarthickness 20mm 找平层leveling blacket 抹灰plastering抹平，找平screeding 抹灰底层rendering coat 抹光，压光trowel finish 灌缝；灌浆grout抹灰罩⾯层setting coat ⼆次灌浆post-grouting 填料filling 翼环plate ring套管pipe sleeve ⽯棉⽔泥asbestos cement 油⿇oil-- hemp 橡胶⽌⽔带rubber water stop 密封胶joint sealant 沥青涂层asphalt coating填缝板joint filler镀锌铁⽪galvanized iron sheet ure ;revetment80mmpile ompressibility area f vibration ssure ol pointsocks。
工程管理专业词汇英汉对照
工程项目管理常用词汇英汉对照“戴明环”“戴明环”Plan - Do - Check - Action, PDCA “交钥匙”承包“交钥匙”承包Turn - key Contract “三时”估计法“三时”估计法Three - Time - Estimate S 曲线曲线S - Curve 按费用设计按费用设计Design - to - Cost 保留金保留金 Retention Money 保险保险Insurance 保证金保证金 Retainage 报表报表Statement 报告关系报告关系Reporting Relationship 报价邀请报价邀请Requestfor Quotation, RFQ 变更指令变更指令Variation Order, Change Order 标前会议标前会议Pre - Bid Meeting 补充资料表补充资料表Schedule of Supplementary lnformation 不可接受风险不可接受风险Unacceptable Risk 不可抗力不可抗力Force Majeure 不可预见不可预见Unforeseeable 不平等条款不平等条款Unequal Term 平衡报价法平衡报价法Unbalanced Bids 材料材料Materials 材料费材料费 Material Cost 财产风险财产风险Probable Risk 留风险留风险 Residual Risk 层次分析法层次分析法Analytic Hierarchy Process 产品产品Product 超前超前Lead 成本预算成本预算Cost Budgeting 承包方承包方 Contractor 承包商代表承包商代表Contractor's Representative 承包商人员承包商人员Contractor's Personnel 承包商设备承包商设备Contracto Contracto’’s Equipment 承包商文件承包商文件Contractor's Documents 承发包方式承发包方式Contract Approach 承诺 Acceptance 承诺诚实信用原则 In Good Faith 诚实信用原则触发器 Triggers 触发器纯粹风险 Pare Risk 纯粹风险次关键路线 Near - Critical Path 次关键路线大型项目 Program 大型项目代理型CM, 非代理型CM CM／Agency, CM／Non Agency 单代号搭接网络图 Multi - Dependency Network 单代号搭接网络图单代号网络图 Activity - on - Network, AON 单代号网络图单价合同 Unit Price Contract 单价合同单时估计法 Single - Time - Estimate 单时估计法担保 Guarantee 担保当地货币 Local Currency 当地货币当事方(一方) Party 到岸价格 Cost lnsurance and Freight, CIF 到岸价格道义索赔 Ex - Gratia Claims 道义索赔德尔裴法 Delphi 德尔裴法调整 Updating, Adjustment 调整定额 Quota 定额动员预付款 Pre - Payment 动员预付款二次风险 Secondary Risk 二次风险法律 Laws 法律反义居先原则 Contra Preferential 反义居先原则返工 Rework 返工方差 V ariance 方差非工作时间 Idle Time 非工作时间费用计划 Cost Planning 费用计划费用索赔 Claims for Lossand Expense 费用索赔分包商 Sub - Contractor 分包商分项工程 Section 分项工程分支网络 Fragnet 分支网络风险 Risk 风险风险定量分析 Quantitative Risk Analysis 风险定量分析风险定性分析 Qualitative Risk Analysis 风险定性分析风险规避 Risk Avoidance 风险规避风险监控 Risk Monitoring and Control 风险监控风险减轻 Risk Mitigation 风险减轻风险接受 Risk Acceptance 风险接受风险类别 Risk Category 风险类别风险评审技术 Venture Evaluation and Review Technique, VERT 风险评审技术风险识别 Risk Identification 风险识别风险应对 Risk期Response 风险应对风险转移 Risk Transference 风险转移付款证书 Payment Certificate 付款证书概率与影响矩阵 Probability and Impact Matrix 概率与影响矩阵赶工 Crashing 赶工个人间的联系 Interpersonal Interfaces 个人间的联系工程变更 Variation, Change 工程变更工程量表 Bill of Quantities 工程量表工程师 The Engineer, Consultant 工程师工程现场勘测 Site Visit 工程现场勘测工程项目采购 Proiect Procurement 工程项目采购工程项目分解 Project Decomposition 工程项目分解工程项目沟通管理 Project Communication Management 工程项目沟通管理工程项目简介 Project Brief 工程项目简介工程项目建设模式 Proiect Construction Approach 工程项目建设模式工程项目决策 Decision to Project 工程项目决策工程项目人力资源管理 Project Human Resource Management 工程项目人力资源管理工程项目审计 Project Audit 工程项目审计工程项目收尾阶段 Project Closure 工程项目收尾阶段工程项目投产准备 Preparation for Proiect Operation 工程项目投产准备工程项目团队 Project Team 工程项目团队工程项目质量 Projectoualitv 工程项目质量工程项目质量控制 Proiect Quality Control 工程项目质量控制工程项目组织方式 Project Organization Approach 工程项目组织方式工期 Proiect Duration 工期工期压缩 Duration Compression 工期压缩工艺关系 Process Relation 工艺关系工作规范 Specification of Work 工作规范工作说明 Statement of Work, SOW 工作说明公开招标 Open Tenderine／Public Invitation 公开招标沟通 Communications 沟通购买—建设—经营经营 Buy - Build - Operate, BBO 顾客 Customer顾客雇主 Employer 雇主雇主人员 Employer's Personnel 雇主人员雇主设备 Employer's Equipment 雇主设备关键活动 Critical Activity 关键活动关键路线 Critical Path 关键路线关键线路法 Critical Path Method, CPM 关键线路法国际标准化组织 International Standard Organization, ISO 国际标准化组织国际项目管理协会 International Project Management Association, IPMA 国际项目管理协会国际咨询工程师联合会 Federation Internationate Des Ingenieurs-Conseils, FIDIC 国际咨询工程师联合会国家私人合作模式 Public - Private Partnership, PPP 国家私人合作模式合同 Contract 合同合同工期 Duration of Contract 合同工期合同管理 Contract Administration 合同管理合同价格 Contract Price 合同价格合同内索赔 Contractual Claims 合同内索赔合同条件 Conditions of Contract 合同条件合同外索赔 Non - Contractual Claims 合同外索赔合同协议书 Contract Agreement 合同协议书合资公司 Joint Enterprise 合资公司横道图 Gantt Charts 横道图环境管理体系 Environmental Management System, EMS 环境管理体系环境绩效 Environmental Performance 环境绩效环境指标 Environmental Target 环境指标回路 Logical Loop 回路混合型合同 Mixed Contract 混合型合同活动持续时间估计 Activity Duration Estimation 活动持续时间估计活动范围 Scope 活动范围活动逻辑关系 Activity Logical Relations 活动逻辑关系活动描述 Activity Description, AD 活动描述活动排序 Activity Sequencing 活动排序活动清单 Activity List 活动清单伙伴模式 Partnering 伙伴模式货物采购 Goods Procurement 货物采购基准计划 Baseline 基准计划基准日期 Base Date 基准日期绩效评估与激励 Performance Appraisaland Reward 绩效评估与激励计划工期 Planned Project Duration 计划工期计划评审技术 Program Evaluation Review Technique, PERT 计划评审技术计日工作计划 Daywork Schedule 计日工作计划计算工期 Calculated Project Duration 计算工期技术规范 Technical Specifications 技术规范技术联系 Technical Interfaces 技术联系价值工程 Value Engineering, VE 价值工程间接费 Indirect Cost 间接费监理工程师 The Engineer, Supervision Engineer 监理工程师监视 Monitoring 监视检查表 Checklist 检查表建设工期 Durationof Project Construction 建设工期建设—经营—拥有—转让 Build - Operate - Own - Transfer, BOOT 建设—经营—拥有—转让建设—经营—转让 Build - Operate - Transfer, BOT 建设—经营—转让建设实施 Construction 建设实施建设—拥有—经营 Build - Own - Operate, BOO 建设—拥有—经营建设—转让—运营 Build - Transfer - Operate, BTO 建设—转让—运营建设准备 Construction Preparation 建设准备建议书邀请 Request for Proposal, RFP 建议书邀请建筑师 Architect 建筑师接收证书 Taking - Over Certificate 接收证书节点 Node 节点节点编号 Node Number 节点编号结束到结束 Finishto Finish, FTF 结束到结束结束到开始 Finishto Start, FTS 结束到开始截止日期 As - of Date 截止日期紧后活动 Back Closely Activity 紧后活动紧前活动 Front Closely Activity 紧前活动进度报告 Progress Reports 进度报告进度偏差 Schedule Variance, SV 进度偏差纠正措施 Corrective Action 纠正措施矩阵型组织结构 Matrix Organization 矩阵型组织结构决策树分析 Decision Tree Analysis 决策树分析决策网络计划法 Decision Network, DN 决策网络计划法竣工时间 Time for Completion 竣工时间竣工试验 Tests on Completion 竣工试验竣工验收 Project Acceptance 竣工验收开工日期 Commencement Date 开工日期开始到结束 Start to Finish, STF 开始到结束开始到开始 Start to Start, STS 开始到开始可交付成果 Deliverable 可交付成果可接受风险 Acceptable Risk 可接受风险可原谅的延误 Excusable Delay 可原谅的延误控制 Control 控制控制图 Control Charts 控制图快速路径法 Fast Track 快速路径法类比估计 Analogous Estimating 类比估计离岸价格 Free on Board, FOB 离岸价格里程碑 Milestone 里程碑历史数据 Historical Results 历史数据利润 Profit 利润例外计划报告 Exception Report 例外计划报告联合集团 Consortium 联合集团联营体 Joint V enture 联营体临时工程 Temporm. Works 临时工程流程图 Flow Diagram 流程图路径会聚 Path Convergence 路径会聚履约保函 Performance Guarantee 履约保函履约保证 Performance Security 履约保证履约证书 Performance Certificate 履约证书卖方 Seller 卖方蒙特卡罗分析 Monte Carlo Analysis 蒙特卡罗分析敏感性分析 Sensitive Analysis 敏感性分析模糊数学法 Fuzzy Set 模糊数学法拟完工程计划费用 Budgeted Cost of Work Scheduled, BCWS 拟完工程计划费用逆推法 Backward Pass 逆推法欧洲发展基金会 European Development Fund, EDF 欧洲发展基金会巴雷托图 Pareto Diagrams 排列图, 巴雷托图偏差变量 Cost V ariance, CV 偏差变量评标 Bid Evaluation 评标期望值 Expectation 期望值期中付款证书 Interim Payment Certificate 期中付款证书启动 Initiation 启动起始节点 Start Node 起始节点潜在的损失值 Risk Event V alue 潜在的损失值赢得值法 Earned V alue 曲线法, 赢得值法全面质量控制 Total Quality Control, TQC 全面质量控制权变措施 Workoround 权变措施缺陷通知期限 Defects Notification Period 缺陷通知期限确凿证据优先 Prima Facie 确凿证据优先人工费 Labor Cost 人工费人工量 Effort 人工量人力资源 Human Resource 人力资源人身风险 Life Risk 人身风险人为风险 Personal Risk 人为风险人员配备要求 Staffing Requirements 人员配备要求任务 Task 任务上控制线 Upper Control Limit, UCL 上控制线设计方 Designer 设计方设计一建造方式 Design - Build, DB 设计一建造方式设计图纸 Drawings 设计图纸生产设备 Plant 生产设备生命周期成本计算 Life - circle Costing 生命周期成本计算剩余工期 Remaining Duration 剩余工期施工合同 Construction Contract 施工合同施工合同分包 Subcontract 施工合同分包施工合同转让 Assignment 施工合同转让施工机械使用费 Expensesof Using Construction Machinery 施工机械使用费施工进度计划 Construction Schedule 施工进度计划施工组织设计 Construction Planning 施工组织设计时距 Time Difference 时距实际成本 Actual Cost 实际成本实际成本加百分比合同 Cost Plus Percentage - of - Cost Contract 实际成本加百分比合同实际成本加固定费用合同 Cost Plus Fixed - Fee (CPFF) Contract 实际成本加固定费用合同实际成本加奖金合同 Cost Plus Incentive - Fee (CPIF) Contract 实际成本加奖金合同实际开始日期 Actual Start Date, AS 实际开始日期实际完成日期 Actual Finish Date, AF 实际完成日期世界银行 The World Bank 世界银行事件 Event 事件受资源约束的进度计划 Resource - Limited Schedule 受资源约束的进度计划授予合同 Award of Contract 授予合同书面文字优先原则 Written Word Prevail 书面文字优先原则数据日期 Data Date 数据日期双代号时标网络法 Time - Coordinate Network, Time Scale Network 双代号时标网络法双代号网络图 Activity - on - Arrow Network, AOA 双代号网络图税金 Tax 税金私人主动融资 Project Finance Initiative, PFI 私人主动融资松弛时间 Slack 松弛时间索赔 Claims 索赔条形图 Bar Chart 条形图通货膨胀 Currency Inflation 通货膨胀统计和概率法 Statistics 统计和概率法投标 Bidding 投标投标保证 Bid Security 投标保证投标报价 Bid Price 投标报价投标函 Letter of Tender 投标函投标决策 Decision to Bid 投标决策投标人 Bidder 投标人投标人须知 Instruction to Bidders 投标人须知投标书 Tender 投标书投标书附录 Appendix to Tender 投标书附录投标文件的递送 Submission of Bids 投标文件的递送投标邀请书 Initiation to Bids 投标邀请书投标有效期 Bid V alidity 投标有效期投机风险 Speculative Risk 投机风险投资方 Investor 投资方投资估算 Cost Estimating 投资估算投资回报期 Investment Recovery Period 投资回报期图示评审技术 Graphical Evaluation Review Technique, GERT 图示评审技术团队成员 Team Member 团队成员退却计划 Fallback Plan 退却计划外币 Foreign Currency 外币完成百分比 Percent Complete (PC) 完成百分比完工估算 Estimate at Completion, EAC 完工估算完工尚需估算 Estimate to Complete, ETC 完工尚需估算完工预算 Budget at Completion, BAC 完工预算五条件 Unconditional, no Demand 五条件无限竞争性招标 Unlimited Competitive Tendering 无限竞争性招标下控制线 Lower Control Limit, LCL 下控制线现场 Site 现场线路 Path 线路限定性估算 Definitive Estimate 限定性估算项目 Project 项目项目报告 Project Report, PR 项目报告项目档案 Project Files 项目档案项目的执行与监督 Project Executionand Supervision 项目的执行与监督项目定义 Project Defining 项目定义项目风险 Project Risk 项目风险项目干系人 Stakeholder 项目干系人项目管理班子 Project Management Team 项目管理班子项目管理班子的偏好 Preferences of the Project Management Team 项目管理班子的偏好项目管理承包型 Project Management Contract, PMC 项目管理承包型项目管理模式 Project Management Approach 项目管理模式项目管理软件 Project Management Software 项目管理软件项目管理协会 Project Management Institute, PMI 项目管理协会项目管理知识体系 Project Management Body of Knowledge, PMBOK 项目管理知识体系项目管理咨询型 Project Management, PM 项目管理咨询型项目后评价 Project Post - evaluation 项目后评价项目计划 Project Planning 项目计划项目结构分解 Project Breakdown Structure 项目结构分解项目结束 project Closing 项目结束项目内在联系 Project Interfaces 项目界面, 项目内在联系项目进度计划 Project Schedule 项目进度计划项目负责人 Project Manager 项目经理, 项目负责人项目可行性研究 Project Feasibility Study 项目可行性研究项目控制 Project Controlling 项目控制项目评估 Project Appraisal 项目评估项目设计 Project Design 项目设计项目谈判 project Negotiation 项目谈判项目型组织 Projectized Organization 项目型组织项目选定 Project Identification 项目选定项目业主 Owner 项目业主项目预评估 Project Pre - Appraisal 项目预评估项目章程 Project Charter 项目章程项目执行 Project Executing 项目执行项目周期 Project Cycle 项目周期项目准备 Project Preparation 项目准备项目综合管 Project Integration Management 项目综合管信息技术 Information Technology, IT 信息技术虚活动 Dummy Activity 虚活动询价 Solicitation 询价亚洲开发银行 Asian Development Bank, ADB 亚洲开发银行延长工期索赔 Claims for Extensionof Time, Claims for EOT 延长工期索赔邀请招标 SelectiveTenderin6／InvitedBidding 邀请招标要约 Offer 要约已完工程计划费用 Budgeted Costof Work Performed, BCWP 已完工程计划费用已完工程实际费用 Actual Cost of Work Performed, ACWP 已完工程实际费用因果分析图 Cause - and - Effect Diagram 因果分析图银行保函 Bank Guarantee 银行保函应急储备 Contingency Reserve 应急储备应急费 Contingency Allowance 应急费英国土木工程师学会 Institute of Civil Engineer, ICE 英国土木工程师学会营运 Operation 营运影响图 Influence Diagram 影响图永久工程 Permanent works 永久工程优化 Optimization 优化有条件 Conditional 有条件有限竞争性招标 Limited Competitive Tendering 有限竞争性招标预可行性研究 Pre - Feasibility Study 预可行性研究运费在内价 Cost and Freight, CFR 运费在内价暂定金 Provisional Sum 暂定金责任风险 Liability Risk 责任风险招标 Bid Invitation／Tendering 招标招标人拒绝投标书的权利 Right to Reiiect Any or All Bids 招标人拒绝投标书的权利招标准备 Tendering Preparation 招标准备争端裁决委员会 Dispute Adiudication Board, DAB 争端裁决委员会正推法 Forward Pass 正推法直方图 Histogram 直方图直线型组织结构 Line Organization 直线型组织结构直线一职能型组织结构 Line - Functional Organization 直线一职能型组织结构职能型组织 Functional Organization 职能型组织职业健康安全 Occupational Healthand Safety, OHS 职业健康安全制约和限制 Constraintsand Limitations 制约和限制质量 Ouality 质量质量保证 Quality Assurance 质量保证质量成本 Cost of Quality 质量成本质量环 Quality Loop 质量环滞后 Lag 滞后中标函 Letter of Acceptance 中标函中标合同金额 Accepted Contract Amount 中标合同金额中介人 Intermediary 中介人中心线 Center Limit, CL 中心线终止节点 End Node 终止节点重叠 Overlap 重叠主导语言 Ruling Language 主导语言专家谈判估计 Expert Judgement 专家谈判估计咨询方 Consulter 咨询方资料表 Schedules 资料表资源计划 Resource Planning 资源计划资源配置 Resource Requirements 资源配置资源平衡 Resource Leveling 资源平衡资源效果 Resource Capabilities 资源效果子网络 Subnetwork 子网络子项目 Subproject 子项目自然风险 Natural Risk 自然风险自由时差 Free Float, FF 自由时差总承包商 General Contractor 总承包商总价合同 Lump Sum Contract 总价合同总时差 Total Float, TF 总时差租赁一建设一经营 Lease - Build - Operate, LBO 租赁一建设一经营组织关系 Organizational Relation 组织关系组织规划设计 Organizational Planning 组织规划设计组织机构 Organization Structure 组织机构组织结构分解 Organizational Breakdown Structure, OBS 组织结构分解组织联系 Organizational Interfaces 组织联系最悲观时间 Most Pessimistic Time 最悲观时间最迟结束时间 Latest Finish Date, LP 最迟结束时间最迟开始时间 Latest Start Date, I5 最迟开始时间最可能时间 Most Probable Time 最可能时间最乐观时间 Most Optimistic Time 最乐观时间最早结束时间 Earliest Finish Date, EF 最早结束时间最早开始时间 Earliest Start Date, ES 最早开始时间最终报表 Final Statement 最终报表最终付款证书 Pinsl Payment Certificate 最终付款证书。
工程常用英语词汇
目录1、电力设计基本术语2、给水排水设计基本术语3、水泵专业英语词汇4、阀门种类英汉术语对照5、阀门专用英语词汇6、照明术语7、工程结构设计基本术语电力设计基本术语abrasion-Proof component of burner 燃烧器耐磨件arm-brace 撑脚ash conditoner 调灰器basket removal panel 元件盒检修护板BDV blow down valve 疏水阀，排污阀blind 堵板blind flange 法兰堵板/盲板法兰（盖calling 催交campell diagram 叶片埃贝尔曲线dado 墙裙daily service fuel tank level switch 日用油缸液位掣damage 损毁damper 挡板damper linkage 风闸联动装置damper motor 风闸马达damping mat 阻尼垫dangerous earth potential 危险性对地电势dashpot 减震器data transmission 数据传输DC/AC converter 直流电／交流电转换器dead 不带电dead weight 自重decanter 沉淀分取器declaration of conformity 符合标准声明decommissioning 解除运作；停止运作decompression chamber 减压室decorative lighting 装饰照明；灯饰deep bore well pump 深钻井泵defect liability period 故障修理责任期；保用期defectograph 钢缆探伤仪；故障检查仪defence in depth 纵深防御definite sequence 固定次序deflection 偏转；挠度deflector sheave 折向轮；导向轮defrost timer 防霜时间掣defrost unit 溶雪组合dehumidifier 抽湿机deleterious substance 有害物质delivery and return air temperature 送风及回风温度delivery connection 出油接头delivery pressure 输出压力demand side management 用电需求管理demand side management agreement 用电需求管理协议demand side management programme 用电需求管理计划dent 凹痕dental instrument 牙科仪器dental scaler 洗牙具Departmental Administration Division [Electrical and Mechanical Services Department] 行政部〔机电工程署〕Departmental Safety Unit [Electrical and Mechanical Services Department] 部门安全组〔机电工程署〕deposition 沉积物depth measuring facility 深度测量装置derating factor 额定值降低因子derust 除锈descale 清除氧化皮design current 设计电流design parameter 设计参数designated employee 指定雇员detachable grip 可拆除的夹扣Details of Branch Offices of Registered Electrical Contractors 注册电业承办商分行详情申报deterioration 变质；变坏Deutsche Industrie Normen [DIN] 德国工业标准device 器件；装置dewatering 脱水；排水diaphragm 膜片；隔板dielectric strength test 电介质强度测试diesel fuel tank 柴油燃料缸diesel oil 柴油differential gasket 差速器衬垫differential lock 差速器锁differential oil 差速器机油diffuser 透光罩；扩散器dilute 稀释dim sum trolley 点心手推车dim transformer 光暗变压器diminution of value 减值dimmer 调光器；光暗掣；光暗器dip tube 液位探测管Diploma in Electrical Engineering 电机工程学文凭dipstick 量油尺direct current [DC] 直流电direct current control 直流控制direct current electric drive 直流电电力驱动direct current reactor 直流电抗器direct drive 直接驱动direct purging 直接驱气direct-acting lift 直接驱动升降机direct-fired vaporizer 明火直热式汽化器direction arrow 方向箭头direction arrow plate 方向指示板direction indicator 方向指示器Director of Electrical and Mechanical Services 机电工程署署长Directory of Accredited Laboratories 认可实验所名册Directory of Quality System Registration Bodies 品质系统注册团体指南disassemble 拆散discharge 放电；卸载discharge lamp 放电灯；放电管discharge lighting 放电照明设施discharge of electricity 释电；放电discharge valve 排水阀disciplinary board 纪律审裁委员会disciplinary board panel 纪律审裁委员团disciplinary tribunal 纪律审裁小组disciplinary tribunal panel 纪律审裁委员团；纪律审裁委员会discolouring 变色disconnection 截断；截离steam hamerring analysis 汽锤分析steam packing unloading valve 汽封卸载阀steam purity 蒸汽纯度steam seal diverting valve 汽封分流阀steam seal feed valve 汽封给水阀steam water mixture 汽水混合物steel bar 扁钢steel supporting 钢支架steel wire brush 钢丝轮steel works 钢结构step load change 负荷阶跃still air 蒸馏气体stirrup 镫形夹stoikiometric ratio 化学当量比stopper 制动器、塞子storage vessell 贮水箱stppage alarm 停转报警stranded copper cable 铜绞线电缆strength 强度strong backs 支撑stud bolt 柱头螺栓、双头螺栓sub cooling line 欠热管submerged arc welding 埋弧焊substation 配电装置substation island 电气岛superficial corrosion 表面腐蚀superheat 过热度supersaturation 过饱和supervisory instrument 监测装置supply transformer 供电变压器support trunnion 支撑端轴surfactant 表面活性剂surge 喘振suspended diode 中断二极管suspended particles 悬浮颗粒switch board 开关柜switch gear 开关柜sychronization 并网sychroscope 同步指示器、同步示波器T square 丁字尺T/G transformer 发变组tackling system 起吊系统tamped/compacted backfill 夯实回填土tanks and accessories 箱罐和附件taper land thrust bearing 斜面式推力轴承tar epoxy paint 柏油环氧漆tarpaulin 防水布temperature digital display meter 温度数显表tensile test 拉伸试验tension test 拉伸试验，张力试验tensioning rod 拉杆terminal box 接线盒terminal poit 接口termination flange 接口法兰tertiary air 三次风test connection 试验接头test permition 试验合格the expansion coordinate system 热膨胀系统theodilite\transit instrument 经纬仪thermal insulatiion for tuebine casing 汽缸保温thermo resistor 热电阻thermostat 恒温器、恒温调节器thinner 稀释剂threaded flange 螺纹法兰throudh type 直通式、穿入式through bolt 贯穿螺栓、双头螺栓thrust plate 推力板tier tube 间隔管tilting pad 可倾瓦块tilting pad bearing 可倾瓦块轴承tip shroud 围带、环形叶栅外柱面tip speed 叶顶速度toe board/plate (kick plate) 踢脚板top crown plate seal 高冠板式密封装置top girder 顶板top penthouse 顶部雨棚top plan view 俯视图torquemeter 扭矩测量仪totalnumber of welding 焊口总数trajectory 轨道、轨迹transducer board 变送器屏transfer pipe 引出管transition piece 过渡连接件transtion piece 过渡段transverse strength 弯曲强度、抗挠强度transverse stress 横向应力、弯曲应力transverse test 抗弯试验trapezoid corrugated plate seperater 梯形波形板分离器、顶帽travelling crab 小车起重机travelling hoist 移动卷扬机tread width 踏步宽度trestle 组合支架trim and grind the welding 修磨焊点trisector air preheater 三分仓空预器trunk cable pair 主电缆对trunnion air seal assembly 端轴空气密封tube exchanger 管式热交换器tubing stress analysis 管系应力分析turbidity analyser 浊度分析仪turbine lube oil and conditioning system 汽机润滑油及净化系统turning oil 循环油twisted pair conveyer 双绞线传送器undercut 坡口underflow 地流、潜流、下溢union 活接头、管节unit control 单元控制unloadding spout vent fan 卸料口通风风机unloading valve 卸载阀urgent need equipment 急需设备urgtented need equipment 急需设备u-shape hanger chains u形曲链片吊挂装置UT ultrasonic testing 超声波探伤UTS ultimate tensible strength 极限抗拉强度vacuum belt filter 皮带真空吸滤器valve opening chart at load rejection 甩负荷阀门开启阀valve seat body seat 阀座valve spindle 阀轴、阀杆valve stem 阀杆vapor proof 防水灯variable inlet guide vane centrifugal fan 进口可调导叶离心式风机variable moning blade axial flow fan 动叶可调轴流式风机variable moving blade double stage axial fan 动叶可调双级轴流式风机variable speed driver 变速马达variables 变量vent capacity 排放量vent line 放气管ventilator valve 通风阀vernier caliper 游标卡尺vertical deflection 垂直挠度vertical movement 垂直位移vertical spindle coal pulveriser 立式磨煤机vibration isolation 隔振装置viewing lamp 观察指示灯viscosity 粘滞度、内摩擦viscous fluid 粘性液体visual examination of coating 外观质量vlve body 阀体void 无效volatily 挥发分voltage class 电压等级vortex gasket 涡流垫片wall type and retractable soot blower 墙式、伸缩式吹灰器warm air curtain 热风幕rwarming line 加热管water balance 水平衡water induction prevent control 防进水控制water level gauge 水位计water stop flange 止水法兰water supply facility island 水工岛wear hardness 可抗磨能力wear template 防磨板wearing bush 防磨套wearing plate 防磨板、护板weigh feeder 重量计量进料器weld bolt 焊接螺栓weld contamination 焊接杂质weld groove 焊缝坡口weld pass 焊道weld penetration 熔深weld preparation 焊缝坡口加工weld with shop beveled ends 工厂加工坡口焊接welder helment 面罩welding line 焊缝welding plate flange 焊接板式法兰welding rod 焊条welding rods dryer barrel 焊条保温筒welding run 焊道welding seam 对接焊缝welding technological properties 焊接工艺性能welding tool 电焊钳welding torch 焊枪welding wire 焊丝welds counting quantity 焊口统计数量wellington boot 防水长统靴whirl plate 折流板wide column 宽立柱winding resistance 绕组电阻wire feed speed 送丝速度wire netting/metal mesh 铁丝网wire wool 擦洗用的）钢丝绒，百洁丝withstand voltage test 耐压试验working medium 工质worm hole （焊缝）条虫状气孔yield strength 屈服强度yoke 磁轭、人孔压板、座架联板firproof paint 防火漆manifold valve 汇集阀saw trace 锯痕tapping point 取样点bushing current transformer 套管式电流互感器light gauge plate/sheet 薄钢板notch 槽口、凹口holding strip 压板straight edge 校正装置trailing edge 后缘lance 喷枪lighting off 点火gaseous fuel 气体燃料entrain 夹带、传输combustion air 助燃风hot stand by 热备用行波travelling wave模糊神经网络fuzzy-neural network神经网络neural network模糊控制fuzzy control研究方向 research direction副教授associate professor电力系统the electrical power system大容量发电机组large capacity generating set输电距离electricity transmission超高压输电线supervltage transmission power line 投运commissioning行波保护Traveling wave protection自适应控制方法adaptive control process动作速度speed of action行波信号travelling wave signal测量信号measurement signal暂态分量transient state component非线性系统nonlinear system高精度high accuracy自学习功能selflearning function抗干扰能力antijamming capability自适应系统adaptive system行波继电器travelling wave relay输电线路故障transmission line malfunction仿真simulation算法algorithm电位electric potential短路故障short trouble子系统subsystem大小相等，方向相反equal and opposite in direction 电压源voltage source故障点trouble spot等效于equivalent暂态行波transient state travelling wave偏移量side-play mount电压electric voltage附加系统add-ons system波形waveform工频power frequency延迟变换delayed transformation延迟时间delay time减法运算subtraction相减运算additive operation求和器summator模糊规则fuzzy rule参数值parameter values可靠动作action message等值波阻抗equivalent value wave impedance附加网络additional network修改的modified反传算法backpropagation algorithm隶属函数membership function模糊规则fuzzy rule模糊推理fuzzy reasoning样本集合 sample set给定的given模糊推理矩阵fuzzy reasoning matrix采样周期sampling period三角形隶属度函数Triangle-shape grade of membership function 负荷状态load conditions区内故障troubles inside the sample space门槛值threshold level采样频率sampling frequency全面地all sidedly样本空间sample space误动作malfunction保护特性protection feature仿真数据simulation data灵敏性sensitivity小波变换wavelet transformation神经元neuron谐波电流harmonic current电力系统自动化power system automation继电保护relaying protection中国电力 China Power学报 journal初探primary exploration标准的机组数据显示 (Standard Measurement And Display Data)负载电流百分比显示 Percentage of Current load(%)单相/三相电压 Voltage by One/Three Phase (Volt.)每相电流 Current by Phase (AMP)千伏安 Apparent Power (KVA)中线电流 Neutral Current (N Amp)功率因数 Power Factor (PF)频率 Frequency(HZ)千瓦 Active Power (KW)千阀 Reactive Power (KVAr)最高/低电压及电流 Max/Min. Current and Voltage输出千瓦/兆瓦小时 Output kWh/MWh运行转速 Running RPM机组运行正常 Normal Running超速故障停机 Overspeed Shutdowns低油压故障停机 Low Oil Pressure Shutdowns高水温故障停机 High Coolant Temperature Shutdowns起动失败停机 Fail to Start Shutdowns冷却水温度表 Coolant Temperature Gauge机油油压表 Oil Pressure Gauge电瓶电压表 Battery Voltage Meter机组运行小时表 Genset Running Hour Meter怠速-快速运行选择键 Idle Run – Normal Run Selector Switch运行-停机-摇控启动选择键 Local Run-Stop-Remote Starting Selector Switch其它故障显示及输入 Other Common Fault Alarm Display and input给水排水设计基本术语一、通用术语给水排水工程的通用术语及其涵义应符合下列规定：1、给水工程water supply engineering 原水的取集和处理以及成品水输配的工程。
模具工程常用词汇英汉对照(超全汇总)
常見鈑金設計術語中英文對照表海外工程图面标注说明英文化.中文名称英文名称中文名称英文名称向上抽孔upward extrude 压线 score 向下抽孔downward extrude 垫脚 locator 正面压螺母(钉)(柱) positive pressing nut(screw) (standoff)色拉孔counter sink反面压螺母(钉)(柱) negative pressing nut(screw) (standoff)向上凸点upward bump正面色拉孔 positive counter sink向下凸点downward bump反面色拉孔negative counter向上半剪upward halt-shear 向上抽芽孔 upward threaded holedownward halt-shear 向下抽芽孔downward threaded 半剪 halt-shear向上反折压平upward folding and flattening 接地标志向下反折压平downward folding and flattening 螺柱点焊 spot weld 穿孔(通孔) through hole丝印 silk screen 抽引,抽凸draw, extrude攻芽 tap 冲孔pierce(pier cing)断差 offset 变形deformatio n压平(两个料厚) hem 成形form(formi ng)向上抽引,抽凸upward draw, form 凸点bump抽凸downward draw, form 拉钉 rivet 扩孔enlarge hole 规格大小specificati on代号 mark 数量amount加工性质character 备注instruction表二 (钣金设计中常用的其它术语)中文名称英文名称中文名称英文名称扩孔enlarge hole 自铆self-chinching 全周压毛边all round burr 平头拉钉 set-head rivet 表面处理finish 定位销 dowel pin挂钩hook 平头铆钉closed-end rivet焊接线weld line 塑料固定栓fastener,plastic,push-type 压合胶粘剂pressuresensitiveadhesive 尼龙绑带tie wrap,五金件hardware 泡棉静电导片gasket, foam, emi 贴纸labeling 铍铜静电导片 gasket, beck, emi 烤漆 paint 圆头螺钉button-head screw电镀plating 平头螺母 nut flush铭板nameplate 平齐自铆flush, self-clinching 包装packing 紧固螺丝 fix screw铁材零件sheetmetal parts 组装assembly 塑料零件plastic parts 凹陷,顶针 sink mark压边铆钉open-endrivet / /插孔 jackcaps表三 (钣金设计中常用的其它术语)中文名称英文名称中文名称英文名称厚度 thick 文字,记号char actor半冲孔spring slice 角corner基座chassis 自锁螺母 nut self-clenching 承座bracket 轴肘式铆接toggle lock 承架horsing 卡尺 caliper 下盖 base 打印字模stamp letter去毛边deburr反面 far side正面inside下料blank(blan king)去除remove量具measuring tools板规 plate gauge比例规proportion al dividersstandard gauge齿轮规gear tooth gauge丁字尺 t-square分线规divider; dividers钢尺 steel rule工作量规working gauge厚薄规feeler(gau ge)角尺 angle square角规 angle gauge金属卷尺metallic tape卡尺calipers; caliper刻度尺graduation ruler块规gauge(blo ck)量规gauge螺距规screw pitch螺纹千分尺 screw micromete 内径千分尺micromete r inside caliper; inside内卡钳inside caliper皮尺tape(/mea sure)surface gauge千分表dial千分尺micromete 曲尺carpenters square三角尺 set square深度千分尺micromete r depth gauge; depth椭圆规ellipsogra ph外径千分尺 outside micromete 外卡钳outside caliper隙规gap(/clear ance)线规 wire gauge斜角规bevel square游标卡尺vernier caliper圆规compasse 折尺folding pocket measure(/直尺straight edge中心规centre gauge锥度规taper gaugecombinati on set。
工程项目管理专用词汇英汉对照
工程项目管理常用词汇英汉对照“戴明环”Plan - Do - Check - Action, PDCA“交钥匙”承包Turn - key Contract“三时”估计法Three - Time - EstimateS曲线S - Curve按费用设计Design - to - Cost保留金Retention Money保险Insurance保证金Retainage报表Statement报告关系Reporting Relationship报价邀请Requestfor Quotation, RFQ变更指令Variation Order, Change Order标前会议Pre - Bid Meeting补充资料表Schedule of Supplementary lnformation 不可接受风险Unacceptable Risk不可抗力Force Majeure不可预见Unforeseeable不平等条款Unequal Term平衡报价法Unbalanced Bids材料Materials材料费Material Cost财产风险Probable Risk留风险Residual Risk层次分析法Analytic Hierarchy Process产品Product超前Lead成本预算Cost Budgeting承包方Contractor承包商代表Contractor's Representative承包商人员Contractor's Personnel承包商设备Contracto’s Equipment承包商文件Contractor's Documents承发包方式Contract Approach承诺Acceptance诚实信用原则In Good Faith触发器Triggers纯粹风险Pare Risk次关键路线Near - Critical Path大型项目Program代理型CM, 非代理型CM CM／Agency, CM／Non Agency 单代号搭接网络图Multi - Dependency Network单代号网络图Activity - on - Network, AON单价合同Unit Price Contract单时估计法Single - Time - Estimate担保Guarantee当地货币Local Currency当事方(一方) Party到岸价格Cost lnsurance and Freight, CIF 道义索赔Ex - Gratia Claims德尔裴法Delphi调整Updating, Adjustment定额Quota动员预付款Pre - Payment二次风险Secondary Risk法律Laws反义居先原则Contra Preferential返工Rework方差Variance非工作时间Idle Time费用计划Cost Planning费用索赔Claims for Lossand Expense分包商Sub - Contractor分项工程Section分支网络Fragnet风险Risk风险定量分析Quantitative Risk Analysis风险定性分析Qualitative Risk Analysis风险规避Risk Avoidance风险监控Risk Monitoring and Control风险减轻Risk Mitigation风险接受Risk Acceptance风险类别Risk Category风险评审技术Venture Evaluation and Review Technique, VERT 风险识别Risk Identification风险应对Risk期Response风险转移Risk Transference付款证书Payment Certificate概率与影响矩阵Probability and Impact Matrix赶工Crashing个人间的联系Interpersonal Interfaces工程变更Variation, Change工程量表Bill of Quantities工程师The Engineer, Consultant工程现场勘测Site Visit工程项目采购Proiect Procurement工程项目分解Project Decomposition工程项目沟通管理Project Communication Management工程项目简介Project Brief工程项目建设模式Proiect Construction Approach工程项目决策Decision to Project工程项目人力资源管理Project Human Resource Management工程项目审计Project Audit工程项目收尾阶段Project Closure工程项目投产准备Preparation for Proiect Operation工程项目团队Project Team工程项目质量Projectoualitv工程项目质量控制Proiect Quality Control工程项目组织方式Project Organization Approach工期Proiect Duration工期压缩Duration Compression工艺关系Process Relation工作规范Specification of Work工作说明Statement of Work, SOW公开招标Open Tenderine／Public Invitation沟通Communications购买—建设—经营Buy - Build - Operate, BBO顾客Customer雇主Employer雇主人员Employer's Personnel雇主设备Employer's Equipment关键活动Critical Activity关键路线Critical Path关键线路法Critical Path Method, CPM国际标准化组织International Standard Organization, ISO国际项目管理协会International Project Management Association, IPMA 国际咨询工程师联合会 Federation Internationate Des Ingenieurs-Conseils, FIDIC 国家私人合作模式Public - Private Partnership, PPP合同Contract合同工期Duration of Contract合同管理Contract Administration合同价格Contract Price合同内索赔Contractual Claims合同条件Conditions of Contract合同外索赔Non - Contractual Claims合同协议书Contract Agreement合资公司Joint Enterprise横道图Gantt Charts环境管理体系Environmental Management System, EMS环境绩效Environmental Performance环境指标Environmental Target回路Logical Loop混合型合同Mixed Contract活动持续时间估计Activity Duration Estimation活动范围Scope活动逻辑关系Activity Logical Relations活动描述Activity Description, AD活动排序Activity Sequencing活动清单Activity List伙伴模式Partnering货物采购Goods Procurement基准计划Baseline基准日期Base Date绩效评估与激励Performance Appraisaland Reward计划工期Planned Project Duration计划评审技术Program Evaluation Review Technique, PERT 计日工作计划Daywork Schedule计算工期Calculated Project Duration技术规范Technical Specifications技术联系Technical Interfaces价值工程Value Engineering, VE间接费Indirect Cost监理工程师The Engineer, Supervision Engineer监视Monitoring检查表Checklist建设工期Durationof Project Construction建设—经营—拥有—转让Build - Operate - Own - Transfer, BOOT建设—经营—转让Build - Operate - Transfer, BOT建设实施Construction建设—拥有—经营Build - Own - Operate, BOO建设—转让—运营Build - Transfer - Operate, BTO建设准备Construction Preparation建议书邀请Request for Proposal, RFP建筑师Architect接收证书Taking - Over Certificate节点Node节点编号Node Number结束到结束Finishto Finish, FTF结束到开始Finishto Start, FTS截止日期As - of Date紧后活动Back Closely Activity 紧前活动Front Closely Activity 进度报告Progress Reports进度偏差Schedule Variance, SV 纠正措施Corrective Action矩阵型组织结构Matrix Organization决策树分析Decision Tree Analysis 决策网络计划法Decision Network, DN 竣工时间Time for Completion 竣工试验Tests on Completion竣工验收Project Acceptance开工日期Commencement Date 开始到结束Start to Finish, STF开始到开始Start to Start, STS可交付成果Deliverable可接受风险Acceptable Risk可原谅的延误Excusable Delay控制Control控制图Control Charts快速路径法Fast Track类比估计Analogous Estimating 离岸价格Free on Board, FOB里程碑Milestone历史数据Historical Results利润Profit例外计划报告Exception Report联合集团Consortium联营体Joint Venture临时工程Temporm. Works流程图Flow Diagram路径会聚Path Convergence履约保函Performance Guarantee 履约保证Performance Security 履约证书Performance Certificate卖方Seller蒙特卡罗分析Monte Carlo Analysis敏感性分析Sensitive Analysis模糊数学法Fuzzy Set拟完工程计划费用Budgeted Cost of Work Scheduled, BCWS 逆推法Backward Pass欧洲发展基金会European Development Fund, EDF排列图, 巴雷托图Pareto Diagrams偏差变量Cost Variance, CV评标Bid Evaluation期望值Expectation期中付款证书Interim Payment Certificate启动Initiation起始节点Start Node潜在的损失值Risk Event Value曲线法, 赢得值法Earned Value全面质量控制Total Quality Control, TQC权变措施Workoround缺陷通知期限Defects Notification Period确凿证据优先Prima Facie人工费Labor Cost人工量Effort人力资源Human Resource人身风险Life Risk人为风险Personal Risk人员配备要求Staffing Requirements任务Task上控制线Upper Control Limit, UCL设计方Designer设计一建造方式Design - Build, DB设计图纸Drawings生产设备Plant生命周期成本计算Life - circle Costing剩余工期Remaining Duration施工合同Construction Contract施工合同分包Subcontract施工合同转让Assignment施工机械使用费Expensesof Using Construction Machinery施工进度计划Construction Schedule施工组织设计Construction Planning时距Time Difference实际成本Actual Cost实际成本加百分比合同Cost Plus Percentage - of - Cost Contract实际成本加固定费用合同Cost Plus Fixed - Fee (CPFF) Contract实际成本加奖金合同Cost Plus Incentive - Fee (CPIF) Contract实际开始日期Actual Start Date, AS实际完成日期Actual Finish Date, AF世界银行The World Bank事件Event受资源约束的进度计划 Resource - Limited Schedule授予合同Award of Contract书面文字优先原则Written Word Prevail数据日期Data Date双代号时标网络法Time - Coordinate Network, Time Scale Network 双代号网络图Activity - on - Arrow Network, AOA税金Tax私人主动融资Project Finance Initiative, PFI松弛时间Slack索赔Claims条形图Bar Chart通货膨胀Currency Inflation统计和概率法Statistics投标Bidding投标保证Bid Security投标报价Bid Price投标函Letter of Tender投标决策Decision to Bid投标人Bidder投标人须知Instruction to Bidders投标书Tender投标书附录Appendix to Tender投标文件的递送Submission of Bids投标邀请书Initiation to Bids投标有效期Bid Validity投机风险Speculative Risk投资方Investor投资估算Cost Estimating投资回报期Investment Recovery Period图示评审技术Graphical Evaluation Review Technique, GERT 团队成员Team Member退却计划Fallback Plan外币Foreign Currency完成百分比Percent Complete (PC)完工估算Estimate at Completion, EAC完工尚需估算Estimate to Complete, ETC完工预算Budget at Completion, BAC五条件Unconditional, no Demand无限竞争性招标Unlimited Competitive Tendering下控制线Lower Control Limit, LCL现场Site线路Path限定性估算Definitive Estimate项目Project项目报告Project Report, PR项目档案Project Files项目的执行与监督Project Executionand Supervision项目定义Project Defining项目风险Project Risk项目干系人Stakeholder项目管理班子Project Management Team项目管理班子的偏好Preferences of the Project Management Team 项目管理承包型Project Management Contract, PMC项目管理模式Project Management Approach项目管理软件Project Management Software项目管理协会Project Management Institute, PMI项目管理知识体系Project Management Body of Knowledge, PMBOK 项目管理咨询型Project Management, PM项目后评价Project Post - evaluation项目计划Project Planning项目结构分解Project Breakdown Structure项目结束project Closing项目界面, 项目内在联系Project Interfaces项目进度计划Project Schedule项目经理, 项目负责人Project Manager项目可行性研究Project Feasibility Study项目控制Project Controlling项目评估Project Appraisal项目设计Project Design项目谈判project Negotiation项目型组织Projectized Organization项目选定Project Identification项目业主Owner项目预评估Project Pre - Appraisal项目章程Project Charter项目执行Project Executing项目周期Project Cycle项目准备Project Preparation项目综合管Project Integration Management信息技术Information Technology, IT虚活动Dummy Activity询价Solicitation亚洲开发银行Asian Development Bank, ADB延长工期索赔Claims for Extensionof Time, Claims for EOT邀请招标SelectiveTenderin6／InvitedBidding要约Offer已完工程计划费用Budgeted Costof Work Performed, BCWP已完工程实际费用Actual Cost of Work Performed, ACWP 因果分析图Cause - and - Effect Diagram银行保函Bank Guarantee应急储备Contingency Reserve应急费Contingency Allowance英国土木工程师学会Institute of Civil Engineer, ICE营运Operation影响图Influence Diagram永久工程Permanent works优化Optimization有条件Conditional有限竞争性招标Limited Competitive Tendering预可行性研究Pre - Feasibility Study运费在内价Cost and Freight, CFR暂定金Provisional Sum责任风险Liability Risk招标Bid Invitation／Tendering招标人拒绝投标书的权利Right to Reiiect Any or All Bids招标准备Tendering Preparation争端裁决委员会Dispute Adiudication Board, DAB 正推法Forward Pass直方图Histogram直线型组织结构Line Organization直线一职能型组织结构Line - Functional Organization职能型组织Functional Organization职业健康安全Occupational Healthand Safety, OHS 制约和限制Constraintsand Limitations质量Ouality质量保证Quality Assurance质量成本Cost of Quality质量环Quality Loop滞后Lag中标函Letter of Acceptance中标合同金额Accepted Contract Amount中介人Intermediary中心线Center Limit, CL终止节点End Node重叠Overlap主导语言Ruling Language专家谈判估计Expert Judgement咨询方Consulter资料表Schedules资源计划Resource Planning资源配置Resource Requirements资源平衡Resource Leveling资源效果Resource Capabilities子网络Subnetwork子项目Subpmject自然风险Natural Risk自由时差Free Float, FF总承包商General Contractor总价合同Lump Sum Contract总时差Total Float, TF租赁一建设一经营Lease - Build - Operate, LBO组织关系Organizational Relation组织规划设计Organizational Planning组织机构Organization Structure组织结构分解Organizational Breakdown Structure, OBS 组织联系Organizational Interfaces最悲观时间Most Pessimistic Time最迟结束时间Latest Finish Date, LP最迟开始时间Latest Start Date, I5最可能时间Most Probable Time最乐观时间Most Optimistic Time最早结束时间Earliest Finish Date, EF最早开始时间Earliest Start Date, ES最终报表Final Statement最终付款证书Pinsl Payment Certificate。
常用理工科专业词汇英汉对照表
常用无损检测专业词汇英汉对照表Aablution 清洗Absorbed dose 吸收剂量A.C magnetic saturation 交流磁饱Absorbed dose rate 吸收剂量率和acceptance specification 验收规范Acceptanc limits 验收范围Acceptance level 验收水平验收标准Acceptance standard 验收标准Accessories 附件配件辅助设备辅助器材Accumulation test 累积检测Accuracy 精确度准确度acetone 丙酮Acoustic emission transducer 声发Acoustic emission count 声发射计数射换能器Acoustic emission (AE) 声发射Acoustic holography 声全息术Acoustic impedance matching 声阻Acoustic impedance 声阻抗抗匹配Acoustic impedance method 声阻法Acoustic wave 声波Acoustic-ultrasonic 声-超声（AU）Acoustical lens 声透镜across 交叉横过Activation 活化Activity 活度Adequate shielding 适当防护、适当屏蔽address: 地址: additional stress 附加应力AE 声发射air header 集气管air set 空气中凝固, 常温自硬自然硬化air supply 气源aisle 过道走廊alkaline battery 碱性电池alarm level 报警电平alarm condition 报警状态allowable variation 允许偏差容Alignment 对准定位调整校直许变化alternating current 交流电aluminum powder 铝粉amount 数量Ampere turns 安匝数amplifier panel 放大器面板Amplitude 振幅、幅度anchor bolt 锚定螺栓地脚螺栓Angle beam method 斜射法、角波束analyzer 分析器法Angle beam probe 斜探头、角探头Angle of incidence 入射角Angle of reflection 反射角Angle of spread 扩散角Angle of squint 偏向角、偏斜角Angle probe 斜探头、角探头Angstrom unit 埃(长度单位) angle square 角尺angle iron 角钢角铁angle steel 角钢angle fitting 弯头application drawing 操作图应用图arc welding 电弧焊arc cutting 电弧切割arc gouging 电弧刨削arc starting 起弧Area amplitude response curve 面积振幅响应曲线Area of interest 评定区、关注区域Arliflcial disconlinuity 人工不argon arc welding 氩弧焊连续性、人工缺陷arrival time interval（Δtij）到arrangement diagram 布置图达时间差(Δtij)Artifact 人为缺陷Artificial defect 人工缺陷A-scan A型扫描A-scope A型显示assembly 装配Attenuation coefficient 衰减系数Audible leak indicator 音响泄漏指Attenuator 衰减器示器Automatic testing 自动检测Autoradiography 自动射线照相术automatic temperature recorder 温度自动记录器axonometric drawing 轴测图axiality 同轴度轴对称性Bback-feed 反馈background target 目标本底backwall echo 底波底面回波baiting valve 放料阀banjo fixing 对接接头band plate 带板Barium concrete 钡混凝土Barn 靶Base fog 片基灰雾Bath 槽液、浴池、槽base material 基底材料Bayard-Alpert ionization gage B-A型电离计Beam 声束、光束Beam ratio 光束比Beam angle 波束角、束张角Beam path location 声程定位、声束Beam axis 声束轴线路径位置Beam path 声程、声束路径Beam spread 声束扩散bellow type 波纹管式beveled edges 坡口Bending 挠曲弯曲beveling 磨斜棱磨斜边成斜角bending deformation 挠曲变形弯曲变形Betatron 电子感应加速器Bimetallic strip gage 双金属片计Bid 投标出价bend 弯管弯头弯曲Black light filter 黑光滤波器、黑Bipolar field 双极磁场光过滤片bisectrix 等分线Black light 黑光，紫外光Blackbody 黑体Bleakney mass spectrometer 波利克Blackbody equivalent temperature 黑体等效温度尼质谱仪blowhole 喷水孔通风孔通气孔 (气)孔铸孔砂[气]眼气泡Bleedout 渗出、漏出blind 挡板窗帘blinding plate 盲板blind plate 隔离盲板盲板block up 封堵垫高bolt 螺栓螺钉bolton 螺栓紧固bonding wire 接合线焊线boost pressure 升压bottom plate 底板Bottom echo 底波底面回波both sides welding 双面焊接Bottom surface 底面Boundary echo 边界回波、界面回波branch connection 分支接续分支Brand name 商标名称品牌连接Bremsstrahlung 轫致辐射Broad-beam 宽射束宽（声、光）束bridge 桥breaking of contact 断接卡Brush application 刷涂B-scan presentation B型扫描显示B-scan B型扫描 B扫描B-scope B型显示buckling deformation 翘曲变形buckle 满扣扣住buried depth 埋深butt joint 对接butt jointing 对接接头burn through 烧蚀烧穿butt weld 对接焊缝butt welding 对接焊bus duct 母线槽CC-scan C型扫描 C扫描C-scope C型显示C-shape detector C型探测器（X射线实时成像）cable fitting电缆配件cable routing电缆路由选择cable gland 电缆衬垫cable tray 电缆盘cable armor 电缆铠装Cable sheath 电缆包皮层cable testing bridge 电缆测试电桥cable laying 电缆敷设cable channel 电缆槽电缆管道cable trunk 电缆管道电缆主干线Capping ends 顶盖末端calculation sheet 计算书calorimeter 热量计Calibration instrument 校准仪器Capillary action 毛细管作用carbon steel tube 碳钢管carbon steel 碳钢Carry over of penetrate 渗透剂转Carrier fluid 载液入cascade connection 串联连接Cassette 暗盒Cathode 阴极caulking metal 填隙合金[金属](材cathodic protection system 阴极保护系统料)CCD Camera 电荷耦合摄像机center line 中心线center plate 中心板拨盘centralized 集中的cement lined piping 水泥衬里管线channel bases沟渠基底center bearing bracket 中心支架Charge Coupled Device 电荷耦合器certification of fitness 质量合格证书件（简称CCD）Central conductor method 中心导体Central conductor 中心导体中线（三相四线制）法channel steel expansion ring 槽钢centripetal canting pull rope 向心斜拉索胀圈Characteristic curve of film 胶片Characteristic curve 特性曲线特性曲线Characteristic radiation 特征辐射标识辐射Chemical fog 化学灰雾check against 检查, 核对chipping 修琢check valve 止回阀chronometer精密计时表Cine-radiography 射线(活动)电影Ci 居里摄影术连续射线照相Circuit breaker断路开关circumferential weld 环焊缝Circumferential field 周向磁场Circumferential coils 圆环线圈环形磁场Circumferential magnetization method 周向磁化法circumferential joint 周圈接缝civil engineer 土木工程师civil works 土建工程建筑工程Clean 清理clamp 夹钳clamping fixture 胎具夹具Clean-up 清除Clearing time 定透时间coaxial cable 同轴电缆cockle stairs 螺旋梯Coercive force 矫顽力Coherence 相干性Coherence length 相干长度（谐波列长度）Coil test 线圈试验Coil size 线圈尺寸Coil spacing 线圈间距Coil technique 线圈技术线圈法Coil method 线圈法Coincidence discrimination 符合Coil reference 线圈参考（参照线圈）性鉴别一致性鉴别cold lap 冷隔Cold-cathode ionization gage 冷阴极电离计collar extension 环口Collimation 准直Collimator 准直器collision 碰撞冲突color identification 彩色识别Combined colour contrast and fluorescent penetrant 着色荧光渗透剂component part 构件 (组合)零件commencement 开始部件Compressed air drying 压缩空气干Compressional wave 压缩波燥compression pump 压缩机压气机comprehensive analysis and judgement 综合分析判断[泵]compression joint 压接压力接合comply with 遵守company 公司Compton scatter 康普顿散射condensation 冷凝conduit box [电]导管分线匣conducting wire 导线conductive paste 导电膏conduit outlet 电线引出口conduit entry 导管引入装置connector 接线器连接器Console 控制台construction work 施工工程content gauge 液位计contactor 触头接触器触点开关Contact pads 接触垫Continuous linear array 连续线性Continuous emission 连续发射阵列Continuous method 连续法Continuous spectrum 连续谱Continuous wave 连续波Continuously Welded (CW) 连续焊Contrast stretch 对比度扩展Contrast 对比度衬度Contrast agent 对比剂造影剂Contrast aid 反差增强剂Contrast sensitivity 对比灵敏度Copper intensifying screens 铜增Control echo 控制回波感屏control 控制控制器control wiring 控制线路control cable控制电缆操纵索control console 控制台control unit 控制单元control valve actuator 阀控传动机构control valve控制阀convenience receptacle 电源插座core rod 芯棒corresponding 相应的cotton fibre 棉质纤维Couplant 耦合剂Coupling 耦合Coupling medium 耦合介质Coupling losses 耦合损失Cracking 破裂裂纹裂化裂解Creeping wave 爬波蠕变波crate 板条箱柳条箱Critical angle 临界角Cross section 横截面Cross talk 串音Cross-drilled hole 横孔Crystal 晶片晶体Curie point 居里点cubicle 室,箱cushion 垫层衬垫Curie temperature 居里温度Curie(Ci) 居里Current induction method 电流感应Current flow method 通电法电流法法current attenuation 电流衰减Current magnetization method 电流磁化法Cut-off level 截止电平Cutting 切割cutting opening 切孔切开CW (Continuously Welded) 连续焊DDark room packing 暗室包装（在暗室条件下将X射线胶片装入暗盒）data logger 数据记录器datum mark 基准点Dead zone 盲区死区Decay curve 衰变曲线Decibel(dB) 分贝Defect 缺陷Defect resolution 缺陷分辨力Defect detection sensitivity 缺陷探测灵敏度Definition 清晰度定义Demagnetization factor 退磁因子Demagnetization 退磁退磁系数Demagnetizer 退磁装置退磁器Densitometer 黑度计密度计Density Strip 黑度比较片密度比Density 黑度（底片）密度较条Density comparison strip 黑度比较片密度比较条depth scan 深度扫描description 说明描述design pressure 设计压力Detecting medium 检验介质Detergent remover 洗净液去垢剂Developer 显像剂显影剂Developer station 显像工位显影台Developer aqueous 水性显像剂Developer dry 干式显象剂Developer liquid film 液膜显象剂Developing time 显像时间显影时Developer nonaqueous（suspend）非水（悬浮）显象剂间differential discriminator (电子) Development 显影差动式鉴频器Diffraction mottle 衍射斑点衍射斑纹Diffuse indications 扩散指示Digital image acquisition system Diffusion 扩散漫射数字图像采集系统Digital display 数字显示数显Dilatational wave 膨胀波疏密波Digital timer for darkroom 暗室用计时器（在暗室中可调及报警）Digital Thermometer 数字温度计（用于测定胶片处理液的温度）digital detector 数字探测器（X射dimensional inspection 尺寸检验线实时成像）Direct contact magnetization 直接Dip and drain station 浸渍和流滴工位浸渍与滴落台接触磁化Direct exposure imaging 直接曝光成像Direct contact method 直接接触法directional beam 定向辐射（指定向辐射的工业X射线机）Directivity 指向性disassembly and assembly 拆装Discontinuity 不连续性Distance-gain-size DGS曲线（距离-增益-尺寸曲线）（DGS德文为AVG）Distance marker 距离标志distribution board 配电盘, 配电屏Dose equivalent 剂量当量dosimeter 剂量计Dose rate meter 剂量率计Dosemeter 剂量计Double crystal probe 双晶探头Double probe technique 双探头法doubleskin 重皮dose 剂量Double traverse technique 双光路Double transceiver technique 双发双收法技术down lead 引下线Dragout 废酸洗液Drain time 滴落时间排液时间drain 排水管排水沟排水道排水draught 气流drying 烘干Drift 漂移Dry method 干法Dry powder 干粉Dry technique 干法Dry developer 干式显像剂Dry developing cabinet 干式显像柜Drying oven 干燥箱干燥炉Drying station 干燥工位干燥台Drying time 干燥时间D-scan D型扫描dual element transducers 双晶探头D-scope D型显示双晶片换能器Dual search unit 双探头双探测装置双探测器Dual-focus tube 双焦点(X射线)管due date 到期日预定日期duplicate part 备件Duplex-wire image quality indicator 双线像质指示器双线像质计Duplex wire type Image Quality Indicator 双线型像质指示器双线像质计Duration 持续时间Dwell time 停留时间dye penetrant examination 着色渗Dye penetrant 着色渗透剂透检验Dynamic leak test 动态泄漏检测Dynamic leakage measurement 动态泄漏测量Dynamic range 动态范围Dynamic radiography 动态射线照相法Eearth wire 接地线地线earthing device 接地装置earthing pole 接地极earth resistance 接地电阻Echo 回波Echo frequency 回波频率Echo height 回波高度Echo indication 回波指示Echo transmittance of sound pressure 声压往复透过率Echo width 回波宽度Eddy current 涡流涡电流Eddy current flaw detector 涡流探伤仪Eddy current testing 涡流检测Edge 边缘棱边Edge effect 边缘效应Edge echo 棱边回波Effective focus size 有效焦点尺寸Effective depth penetration （EDP）有效穿透深度有效透入深度Effective magnetic permeability 有效磁导率Effective resistance 有效电阻Effective permeability 有效磁导率有效渗透率相对渗透率Effective reflection surface of flaw 缺陷有效反射面Elastic medium 弹性介质elbow 弯管接头管肘Electric displacement 电位移electric heat tracing 电伴随加热electric force compounded grease 电力复合脂electric pressure 电压electric machine 电机electrified 带电Electrical center 电中心Electrode 电极电焊条electrical panel 配电板,配电盘electrical material电气材料electrical appliance 电器Electromagnet 电磁铁electron linear accelerator 电子直线加速器Electrolytic Sliver recovery unit 电解银回收装置（从定影液中回收银）Electromagnetic induction 电磁感Electro-magnetic acoustic transducer 电磁声换能器应Electromagnetic radiation 电磁辐射Electromagnetic testing 电磁检测Electron radiography 电子辐射照Electro-mechanical coupling factor 机电耦合系数相术Electron volt 电子伏恃Electronic noise 电子噪声Electrostatic spraying 静电喷涂Emulsification 乳化embedded part 预埋件嵌入[埋置] E-mail: 电子邮件: 电子邮箱:部分Emulsification time 乳化时间Emulsifier 乳化剂emission count （声）发射计数Encircling coils 环形线圈End effect 端部效应端点效应Energizing cycle 激励周期enfoldment 折迭end socket 端头, (钢索的)封头Equalizing filter 均衡滤波器平envelope 包络包迹衡滤波器equipment 器材设备Equivalent I.Q.I. Sensitivity 当Equivalent 当量量象质指示器灵敏度Equivalent nitrogen pressure 等效氮压当量氮气压力Equivalent method 当量法Equivalent penetrameter sensifivty 当量透度计灵敏度erection 架设Erasabl optical medium 可消光介质Etching 浸蚀腐蚀侵蚀蚀刻Evaluation threshold 评价阈值评Evaluation 评定定阈Event count 事件计数Event count rate 事件计数率examination 试验检验考试examine and approve 审批Examination area 检验范围Examination region 检验区域exfoliation 剥落脱落Exhaust pressure/discharge pressure 排气压力/排放压力出口压力输送压力Expanded time-base sweep 时基线展Exhaust tubulation 排气管道宽时基扫描扩展expansion joint 伸缩接头expansion bolt 伸缩栓, 扩开螺栓Exposure 曝光Exposure table 曝光表Exposure chart 曝光曲线Exposure fog 曝光灰雾Exposure 曝光Extended source 扩展源延长源external diameter 外径eye survey 目测Ffabrication tolerance 制造容差fabrication 加工制造fabrication drawing 制造图纸制作图fall off 脱落Facility scattered neutrons 易散射中子False indication 假指示虚假指示Family 族系列Far field 远场Fast neutron detectors 快中子探测Fast/slow timing Oscilloscope 带快慢调速的示波器器FBH 平底孔(缩写) Fax: 传真:Feed-through coil 穿过式线圈Field 场（磁场、声场）feeder 馈电线field installation 现场安装field instrument 携带式仪表field fabricated 工地制造的现场装配的ferritic 铁素体的Fill factor 填充系数Film speed 胶片速度(胶片感光速度胶片感光度)fillet weld 角焊填角焊filler rod 焊条filler metal 焊料焊丝film density 胶片密度filling water test 充水试验filament 灯丝Film badge 胶片剂量计Film base 片基film cassette 胶片暗盒Film contrast 胶片对比度Film processing 胶片冲洗加工底Film gamma 胶片γ值（胶片灰度系数）片处理Film Hangers for manual processing 洗片架（手工洗片的胶片挂架）Film Hangers （Clip Type）夹式洗片架（手工洗片的一种洗片架类型）Film Hangers （Channel Type）槽式洗片架（手工洗片的一种洗片架类型）Film processing chemicals 胶片处理药品洗片药品Film unsharpness 胶片不清晰度film viewer 底片评片灯观片灯底Film viewing screen 胶片观察屏片观察用光源Filter 滤波器滤光板过滤器Final test 最终检验Fixing 固定fire barriers 防火间隔防火屏障flange joint 凸缘接头flange connection 凸缘联接flange gasket 法兰垫片flange 边缘轮缘凸缘法兰flange sealing surface 法兰密封面Flaw echo 缺陷回波Flat-bottomed hole equivalent 平Flat-bottomed hole 平底孔底孔当量Flaw characterization 伤特性缺Flaw 伤缺陷瑕疵裂纹陷特征flash plate 闪熔镀层Flexural wave 弯曲波flexible conduit 软管flicker-free images 无闪烁图像Floating threshold 浮动阀值Fluorescence 荧光floor slab 楼板flow sheet 流程图flow instrument 流量计flushing 冲洗填缝flux 焊剂Fluorescent examination method 荧Fluorometallic intensifying screen 荧光金属增感屏光检验法Fluorescent magnetic particle inspection 荧光磁粉检验Fluorescent dry deposit penetrant 干沉积荧光渗透剂Fluorescent light 荧光荧光灯Fluorescent magnetic powder 荧光磁粉Fluorescent penetrant 荧光渗透剂Fluorescent screen 荧光屏Fluoroscopy 荧光检查法Flux leakage field 磁通泄漏场漏fluorography 荧光照相术磁场Flux lines 磁通线Focal spot 焦点Focal distance 焦距Focus length 焦点长度聚焦长度Focus size 焦点尺寸聚焦尺寸Focus width 焦点宽度聚焦宽度Focused beam 聚焦束（声束、光束、Focus electron 电子焦点聚焦电子束电子束）Focusing probe 聚焦探头Fog 灰雾Focus-to-film distance(f.f.d) 焦点-胶片距离（焦距）Fog density 灰雾密度Footcandle 英尺烛光formula 公式foundation ring 底圈foundation settlement 基础沉降Freguency 频率Frequency constant 频率常数Fringe 干涉带干扰带条纹边缘Front distance 前沿距离Front distance of flaw 缺陷前沿距离Full-wave direct current（FWDC）全full-scale value 满刻度值波直流Fundamental frequency 基频Furring 毛状迹痕毛皮fusion 熔融熔合fusion arc welded 熔弧焊GGage pressure 表压表压力gage glass 液位玻璃管Gain 增益gamma camera γ射线照相机（γ射线探伤机）gamma equipment γ射线设备Gamma radiography γ射线照相术Gamma ray source γ射线源Gamma ray source container γ射线源容器Gamma rays γ射线Gamme ray unit γ射线机γ射线装Gamma-ray radiographic equipment γ射线照相装置置gamma source γ射线源γ源Gap scanning 间隙扫查间隙扫描Gas 气体gas cutting 气割gas shielded arc welding 气体保护焊Gating technique 选通技术脉冲选Gate 闸门通技术gauge board 仪表板样板模板规准尺Gauss 高斯Geiger-Muller counter 盖革.弥勒计数器generating of arc 引弧Geometric unsharpness 几何不清晰度girth weld 环形焊缝gland bolt 压盖螺栓Goggles 护目镜gouging 刨削槽Grazing incidence 掠入射切线入Gray(Gy) 戈瑞射Grazing angle 掠射角切线角入射余角grind off 磨掉grinder 磨床磨工grinding wheel 砂轮片砂轮grounding conductor 接地导体Group velocity 群速度grouting 灌（水泥）浆guide wire 尺度[定距]索,准绳gusset plate角撑板, 加固板HHalf life 半衰期Half-wave current （HW）半波电流Half-value method 半波高度法半Half-value layer(HVL) 半值层半价层值法Halogen 卤素Halogen leak detector 卤素检漏仪Hard-faced probe 硬膜探头硬面探头hanger 吊架挂架洗片架Hard hat 安全帽Hard X-rays 硬X射线Harmonic analysis 谐波分析Harmonic distortion 谐波畸变Harmonics 谐频谐波head face 端面Head wave 头波heat exchangers 热交换器heat absorbing glass 吸热玻璃Heating boxes 加热箱heat affected area 热影响区heat transfer 热传输Helium bombing 氦轰击法Helium drift 氦漂移Helium leak detector 氦检漏仪Hermetically tight seal 气密密封密封密封装置High vacuum 高真空high frequency generator 高频发电High energy X-rays 高能X射线机highly sophisticated image processing 高度完善的图像处理hoisting upright column 吊装立柱high frequency 高频Holography 全息照相术（光全息、声全息）horizontal line 水平线Hydrophilic remover 亲水性洗净剂Hydrophilic emulsifier 亲水性乳化剂亲水性去除剂Hydrostatic test 水压试验静水压试验Hysteresis 磁滞滞后hydrostatic pressure test静水压试验IIACS =International Annealed Copper Standard 国际退火(软)铜标准ice 冰ice chest 冰箱ice machine 制冰机，冷冻机iconoscope 光电摄像管ID (①inside ②inside dimensions) ①内径②内部尺寸ID coil ID线圈 =Inside Diameter 内径线圈Image definition 图像清晰度idea 概念，意见，思想ideal 理想的，想象的identical 同一的，恒定的，相同的identification 鉴定，辨别，验明identification mark 识别标志identifier 鉴别器identify pulse 识别脉冲IEM (ion exchange membrane) 离子idiopathetic 自发的，特发的交换膜I.F. (intermediate frequency) 中频（30～3000千周/秒）illuminance 照（明）度illuminant 照明的，发光的illuminating lamp 照明灯泡illuminating loupe 放大照明镜illuminating mirror 照明镜illumination 照明的，照射illumination apparatus 照明器illumination plate 照明板illuminator ①照明器，照明装置②反光镜illuminometer 照度计image amplifier 图像放大器，影像illustration(abbr. illus.) 图解，例证，具体说明增强器image analysis system 图像分析系统image converter 影像转换器Image contrast 图像对比度影像对比Image enhancement 图像增强image intensifier 像亮化器，图像image freeze 影像冻结增强器image intensifier tube 影像增强管图像增强管image pick-up tube 摄像管Image magnification 图像放大Image quality 图像质量image monitor 图像监视器image multiplier 影像倍增器Image Quality Indicator 像质计像质指示器IQI 像质计像质指示器Image quality indicator sensitivity 像质指示器灵敏度imager 图像仪，显像仪image reproducer 显像管，显像器Imaging line scanner 图像线扫描器image quality indication 像质指示图像行扫描器image store 图像存储器image tube 显像管imagination 想象imagine 想象，推测，设想immediate payment 立即付款immersion 浸没，浸渍Immersion rinse 浸没清洗浸液清Immersion probe 液浸探头洗immersion system 浸渍装置液浸系统Immersion testing 液浸试验Immersion time 浸没时间浸入时间impacter 冲击器impact strength 冲击强度Impedance plane diagram 阻抗平面Impedance 阻抗图impedance transducer 阻抗传感器，impedance matching 阻抗匹配阻抗换能器impeller ①叶轮，转子②压缩机imperial quart 英制夸脱imperial gallon(abbr. ip gal) 英国标准加仑（英制容量单位合4.546升）Impulse eddy current testing 脉冲Imperfection 不完整性缺陷涡流检测import ①进口②输入import and export firm 进出口商行importation ①输入，传入②进口货import border station 进口国境站名import licence position 进口许可证impression 压迹，印模，版impression technic 印模术impression tray 印模盘impulse 冲动，搏动，脉冲impulse generator 脉冲发生器impulse oscilloscope 脉冲示波器impulser 脉冲发生器，脉冲传感器impulse recorder 脉冲自动记录器impulse scaler 脉冲计数器impulse transmitting tube 脉冲发impulse timer 脉冲计数器射管In (①indium ②inch) ①铟②英寸impurity 不纯，杂质（等于25.4毫米）inaction 无作用inadequacy 机能不全，闭锁不全Inc. (incorporated) 股份有限公司incandescent lamp 白炽灯inch(abbr.In;in) 英寸incidence ①入射，入射角②发生率incidental 偶发的，非主要的incident illumination 入射光incident light 入射光incident ray 入射光inclined tube type manometer 斜管inclination 倾斜，斜度式压力计include 包括，计入inclusion 包含包埋杂质incoming line 进线口incompatible 不相容的，禁忌的incompetence 机能不全，闭锁不全inconvertible 不可逆的incorporation ①并入②公司increase 增加，增大，增长indent 订单Indicated defect area 缺陷指示面Incremental permeability 增量磁导率积index ①指数，索引②指针index card 索引卡片indexer 指数测定仪，分度器index hand 指针indicated light 指示灯indicating bell 指示铃indicator ①指示器，显示器②指针indicating lamp 指示灯③指示剂indicatrix 指示量，指示线，特征曲indicator paper 试纸线index signal 指示信号indicate 指示，表明Indicated defect length 缺陷指示长度Indication 指示indifferent electrode 无关电极indiffusible 不扩散的indirect export 间接出口indirect import 间接进口indium(abbr.In) 铟individual 个体的，个别的Indirect exposure 间接曝光Indirect magnetization 间接磁化Indirect magnetization method 间接磁化法Indirect scan 间接扫查indoor 室内的induce 引起，感应，诱导induced electricity 感生电，感应电induct 感应，引导，引入inductance bridge flowmeter 感应inductance 电感，感应系数电桥流量计Induced field 感应磁场感生场Induced current method 感应电流法induction ①引导，前言②感应，电inductance meter 电感测定计感③吸气induction apparatus 感应器induction coil 感应线圈inductive transducer 感应传感器inductogram X射线照片inductometer 电感计inductor 感应器，感应机inductorium 感应器inductosyn 感应式传感器industrial(abbr.indust.) 工业的，产品的industrial exhibition 工业展览会industrial robot 工业机器人industry 工业，产业indutrial X-ray machin 工业X射线Industrial X-ray films 工业X射线胶片机industrial radiographic film dryer 工业射线胶片干燥器inert 惰性的，无效的inference 推论，推断infinite 无限的，无穷的infinitesimal 无限小的，无穷小的infinity 无穷大，无限，无限距inflame 燃，着火inflammable 可燃的，易燃的inflation 膨胀，充气，打气inflator 充气机inflow 流入，吸入，进气influence 影响，感应influx 流入，注入information 情报，资料，消息，数inform 报告，通告，告诉据information storage unit 信息存储information generator 信息发送器器infra- 下，低于，内，间infranics 红外线电子学infrared ①红外线的②红外线infrared detector 红外线探测器infrared drier 红外线干燥器infrared equipment 红外线设备infrared gas analyzer 红外线气体infrared furnace 红外线炉分析仪infrared heater 红外线加热器infrared lamp 红外线灯infrared laser 红外激光器infrared light 红外线infrared liner polarizer 红外线直线偏振镜infrared photography 红外摄影术infrared radiation 红外线照射infrared radiator 红外线辐射器infrared spectrophotometer 红外infrared rays 红外线分光光度计Infrared sensing device 红外传感Infrared imaging system 红外成象系统装置infrasonic frequency 次声频infrequent 稀有的，不常见的infrared thermography 红外热成象红外热谱Inherent fluorescence 固有荧光inherent 生来的，固有的，先天的inheritance 遗传，继承inhibition 抑制，延迟，阻滞inhibitor 抑制剂抑制器inhomogeneous 不纯的，不均匀的in-house 自身的，内部的initial 开始的，最初的initial charge 起始电荷initial data 原始数据initiator ①创造人②引发剂Initial permeability 起始磁导率Inherent filtration 固有滤波初始磁导率Initial pulse width 始波宽度始脉Initial pulse 始脉冲冲宽度injection 注射，喷射injection syringe 注射器injector 注射器，喷射器injector pump 注射泵injury 伤，损伤，损害ink 墨水，油墨ink jet printer 墨水喷射印刷机，喷水式打印机ink jet recorder 墨水喷射记录器ink writing oscillograph 记录示波ink writer 印字机仪inlay 嵌体，嵌入inlead 引入线inlet 入口，入线，输入inlet port 入口inner 内部的innocuous 无害的，良性的innovation 革新，改革innumerable 无数的，数不清的ino- 纤维inoperative 无效的，不工作的inorganic 无机的inorganic chemistry 无机化学inosculation 吻合，联合in-out box 输入-输出盒in parallel 并联in phase 同相的input 输入，输入电路input buffer 输入缓冲器input coupler 输入耦合器input device 输入装置input filter 输入滤波器input impedance 输入阻抗input output adapter 输入-输出衔接器input tranformer 输入变压器inscription 标题，注册in series 串联insert ①插入物，垫圈②插入，植入inserter 插入器，插入物insertion 插入insert tube 嵌入式X射线管inset 插页，插图，插入inside 内部，内侧，在……里面Inserted coil 插入式线圈Inside coil 内部线圈Inside-out testing 外泄检测泄出检测Inspection 检查检验insignificant 无意义的，轻微的insolation 曝晒，日照insoluble 不溶解的inspection 验收，检查，商检inspection certificate 检验证明书inspection fee 检验费inspection machine 检验设备inspection standard 检验标准inspector ①测定器②检验员inspectoscope 检查镜Inspection medium 检查介质检验介质Inspection frequency 检测频率inspissator 浓缩器，蒸浓器instability 不稳定性install 安装，装置installation ①安装②装置，设备installation fundamental circle 安装基准圆installing 安装，插入instance 例证，实例，情况instantaneous value 瞬时值，即时值instead 代替，更换instillation 滴注法，灌注institute 学会，协会，研究所instruction ①指示，命令②说明，institution 机关，机构，学校，制度说明书instruction counter 指令计数器instrument 仪器，器械，仪表instrumentation ①器械，设备②器instrumental error 仪器误差械操作法instrument air 仪表气源instrument board 仪表板instrument cabinet 器械柜instrument carriage 器械车instrument case 器械箱instrument cover 仪器外表instrument cupboard 器械柜instrument light 仪表信号灯instrument lubricant 器械润滑剂instrumenent repairing table 器械instrument rack 器械架仪器架修理台instrument stand 仪器架instrument table 器械台，器械桌insulant 绝缘材料insulated cable 绝缘电缆insulated sleeve 绝缘套管insulating oil 绝缘油insulation 绝缘，绝热，隔离insulation resistance 绝缘电阻insulator 绝缘体，绝热体insullac 绝缘漆insusceptible 不受……影响的，不接受……的intact 完整的，未受损伤的integral ①积分（的）②完整的integraph 积分仪integrated circuit microelectrode integrated circuit(abbr.IC) 集成电路集成电路微电极integrated circuit storage 集成电路存储器integrating dosimeter 累计剂量仪integrating instrument 积分仪，积算仪表integrator 积分仪integrogram 积分图integronics 综合电子设备intellect 智力，才智intensifier ①增强器②照明装置Intensifying factor 增感系数Intensifying screen 增感屏intensimeter X射线强度计intensionometer X射线强度量计intensity level ①强度级（声音）②intensity 强度亮度intensity output 声强输出intensive 加强的，集中的，重点的interaction 相互影响，相互作用，inter- 在……中间，内，相互干扰interception 相交，折射（光）interchange 交替，交换interchanger 交换器intercondenser 中间电容器intercooler 中间冷却器interdiction 禁止，制止interest 兴趣，关心，注意，利益interesting 有趣的Interval arrival time （Δtij) 到interface （计算机）接口界面达时间差(Δtij)Interface boundary 界面interface echo 界面回波interfacial tensiometer 界面张力计interfacial tension 界面张力Interface trigger 界面触发Interference 干涉int erference filter ①干涉滤波器interference absorber 干扰吸收器②干涉滤光镜interference refractometer 干涉interference preventer 防干扰装置折射计interference spectroscope 干涉分光镜interferogram 干涉图interferometer 干涉仪，干扰计interferoscope 干涉镜interior angle welding line joint interior 内部，内部的内侧角焊缝接头intermission 间断间歇interlayer 夹层隔层intermediate frequency(abbr.I.F.) 中频（300～3000千周/秒）internal energy 内能internal exposure 体内照射international(abbr.Int.) 国际的，internal gauge 内径规世界的international candle 国际烛光international fair 国际博览会international market 国际市场international standard 国际标准international unit(abbr. I.U) 国international treaty 国际条约际单位interphase 界面interpolation 插入，内插法interpretation 翻译，解释，说明interpreter 翻译程序，翻译机interrupt 断续，中断interrupter 断流器，断续器interspace 空间，间隙，中间interstage amplifier 级间放大器inter-sync 内同步interval 间隔，时间间隔，中断期intervalometer 定时器，时间间隔计interval timer 限时器in toto 全，整体intra- 在内，内，内部interpretation 解释intrasonic 超低频introduce ①引进，引导②前言，绪intro- 入口，在内论introduction 说明书，前言，绪论intromission 插入，输入introscope 内腔检视仪，内孔窥视仪in vacuo 在真空中invagination 凹入，折入，套叠invasive 侵害的，侵入的invention 发明，创造inventor 发明者，创造者inventory ①清单，存货单②设备，机器inversion 转换，逆转inverted cone 倒锥形inverted image 倒像inverter 倒相器，交换器，换流器inverting amplifier 倒相放大器inverting eyepiece 倒像目镜invest 包埋，围模，附于invisible light filter 不可见光滤inv estigation ①调查，研究②调查报告光镜invisible spectrum 不可见光谱involuntary 不随意的，偶然的involve 包含，包括inward 内，向内的Io(ionium) 碘iodide 碘化物iodine(abbr. I) 碘iodo- 碘iodoform 碘仿，三碘甲烷ion pump 离子泵ion 离子ion analyser 离子分析仪ion exchange chromatography 离子ion exchange 离子交换交换色谱法ion exchanger ①离子交换器②离子交换器ion exchange resin 离子交换树脂ionic rays 离子射线ionic strength 离子强度ionic weight 离子量ionization 电离，游离，离子化ionization chamber 电离室ionization constant 电离常数ionization meter 电离测量仪ion source 离子源Ionization chamber 电离室Ionization vacuum gage 电离真空计Ionization potential 电离电位电离真空压力计ion laser 离子激光器ion meter 离子计ionocolorimeter 氢离子比色计ionogram 电离图ionometer ①X射线量计②离子计ionosphere 电离层Ir-192 Gamma ray projector 铱192 Ionography 离子放射照相法γ射线探伤机ionotron 静电消除器ion source 离子源iontoquantimeter ①X射线量计②离子计iontoradiometer X射线量计IP (iso-electric point) 等电点Ir (iridium) 铱ir- “不，无，非”（同in-,但冠于r字头的词前）iraser 红外激射器，红外激光iris ①虹膜②隔膜，膜片③可变光iridium(abbr. Ir) 铱阑iris aperture 可变光圈，可变光阑iron 铁Irradiance E 辐射通量密度，辐照度Iron intensifying screens 铁增感屏Eiron triangle 铁三角架irradiation 照光，辐射irradiator 辐照器，辐射器irregular 不规则的，无规律的irregular lighting 不规则照明irreversibility 不可逆性IR spectrophotometer 红外线分光光度计iso- 同，等，均匀isochore 等容线（在等体积下温度气isobar 等压线压关系曲线）isochrone 等时线，瞬压曲线isochronism 等时性Isolation 隔离度绝缘Isotope 同位素isolation room 隔离室isolator 绝缘体，隔离器，隔离物isomer （同分）异构体isopotential 等电势的，等电的isothermal line 等温线isotope tracer 同位素示踪物ISP(infrared spectrophotometer) isotopic tracer 同位素指示剂，示踪原子红外分光光度计Jjig 夹具jigger rotor 盘车转子job site 施工现场junction box 接线盒分线箱KK value K值Kaiser effect 凯塞(Kaiser)效应Kiloelectron volt 千电子伏特Kilo volt 千伏特（kv）（keV）Krypton 85 氪85LL/D ratio L/D比（长/径比）Lamb wave 兰姆波land (刀刃的)厚度 (纹间)表面 (钻头的)刃带 (活塞的)环槽 (柱塞的)挡圈连接盘焊接区lap width 搭接宽度Latent image 潜象Lateral scan 左右扫查横向扫描lateral translation 侧向平移layout drawing 布置图Latitude of an emulsion 胶片曝光Lateral scan with oblique angle 斜平行扫查宽容度lead foil 铅箔lead pipe铅管Lead intensifying screens 铅增感屏Lead screen 铅屏铅增感屏。
结构英汉对照工程词汇
英汉对照工程常用词汇AN USUAL ENGLISH-CHINESE VOCABULLARY IN ENGINEERING DESIGN（全册）信息产业电子第十一设计研究院有限公司技术质量部二00三年七月编制说明《本英汉对照工程设计常用词汇》原编于1996年12月，收集了我院有关工程设计方面的常用词汇﹑词组和句子。
现在原版的基础上重新进行了统编，为配合院办发[2003]96号《关于提高我院职工英语口语水平的强制性规定》,方便设计人员查阅，并在提高英语口语的同时，也不断提高阅读﹑翻译工程设计文件的能力和水平，以便更好地在工程设计中和外方顾客就技术问题进行有效地沟通与交流。
该“词汇”按专业分成了六部份，虽然多达190页，但还需要不断补充和完善。
技术质量部翻译组的同志将在以后继续做好这项工作。
技术质量部2003年7月30日目录1.图面常用词汇 32.土建部份213.给排水部份614.气动部份865.电气部份966.暖通部份1261. 工程设计图面常用词汇CONCLISE ENGLISH OF DRAWING PACKAGE总论GENERAL图纸目录Drawing list标准图目录Standard drawing list典型图目录Typical drawing list标准、规范目录Standard and regulation list统一详图目录Uniform detail list标准图集Standard drawing collection设备清单Equipment list材料表Material list建筑物、构筑物一览表List of buildings andstructures施工进度表Schedule of construction建筑构件表List of architectural members 管道及管件汇总表Summary of pipes and pipefittings楼面、屋面构造表Construction chart of floor androof各种管道数量表Bill of piping quantity预埋件明细表Schedule of embeddedelements比例Scale无比例、不按比例Not to scale项目名称Project, item标题栏Caption of drawing, drawingheading图号Drawing no.(DWG NO.)张号Page序号No.编号Code型号Type规格Specification单位Unit图例Legend说明Notes备注Remarks由…设计Designed by…由…校对Checked by…由…审核Approved by…由…发行Issued by…专业Specialty总图Site plan土建Civil建筑Architecture结构Structure机械Mechanical给水排水Water supply and drainage暖通Heating, ventilation and airconditioning (HV AC)电气Electrical供电Power supply电照Lighting自控Automatic control通信Communication物理概念Physical concept长度Length宽度Width高度Height净高Clear height深度Depth面积Area体积V olume时间Time速度Speed, velocity温度Temperature湿度Humidity功率Power压力Pressure力Force公斤Kilogram( Kg)克Gram (g)吨Ton (t)米Meter (m)厘米Centimeter (cm)毫米Millimeter (mm)平方米Square meter (㎡)立方米Cubic meter (m3)秒Second (s)分Minute (m)时Hour (h)厚度Thickness直径Diameter半径Radius弯曲半径Curve radius内径Inside diameter外径Outside diameter圆形Circle, round方形Square矩形Rectangle矩形的Rectangular立方体Cube椭圆Ellipse重量Weight毛重Gross weight净重Net weight质量Quality数量Quantity自然条件Natural conditions气象Meteorology气象资料Meteorological data日照Sun shine年平均日照时数Yearly mean sun shine hours 风级Wind class风向Wind direction风力Wind force风向标Weather cock逐月风向频率Monthly wind direction andfrequency最大（平均）风速Maximum (mean) windvelocity主导风向Prevailing wind dirction最大风速Maximum wind velocity台风Typhoon季节风Monsoon降雨资料Rainfall data降雨频率Rainfall frequency降雨强度Rainfall intensity降雨日数Number of rainy days最大（平均）降雨量Maximum (mean) rainfall年降雨量Annual rainfall极限降水量Maximum possiblepricipitation雨量Rain precipitation降雨面积Rain precipitation暴雨Rain area持续时间Rain storm降雨历时Duration暴雨历时Duration of rainfall年平均雷暴时数Duration of rain storm溢流周期Yearly mean lightning andthunder days年平均气温Overflow period年绝对最低气温Yearly absolute temperature, lowest年绝对最高气温Yearly absolute temperature,highest最冷月或最热月平均温度Mean temperature, coldest month or hottest month年、月、平均温度，最高、最低Temperature, yearly, monthly, mean, highest, lowest最高或最低绝对温度Absolute temperature, highestor lowest湿球温度Wet bulb thermometer湿球温度计Wet bulb thermometer干球温度Dry bulb temperature干球温度计Dry bulb thermometer干湿温差Psychometric chart冰冻期Frost period冰冻深度Frost penetration最大积雪深度Maximum snow penetration 采暖地区Region with heating provision 不采暖地区Region without heatingprovision采暖室外计算温度Calculating outdoortemperature for heating通风（冬季）室外计算温度Calculating outdoor temperature for ventilation (winter)绝对大气压Absolute atmospheric pressure 蒸发量Vaporization volume相对湿度Relative humidity建筑材料Building material水泥Cement水泥标号Cement grade硅酸盐水泥Portland cement矿渣硅酸盐水泥Portland slag cement灌浆水泥Grout cement快凝水泥Rapid setting cement防潮水泥Waterproof cement高强度水泥High-strength cement高标号水泥High-strength cement水泥沙浆强度Cement mortar strength水泥沙浆需水量Water demand of cementmortar砖Brick普通粘土砖Common clay brick实心砖Solid brick异形砖Special brick角砖Angle brick拱顶砖Key brick面砖Face brick勒脚砖Springer带槽砖Brick with groove空心砖Hollow brick承重空心砖Load-bearing hollow brick通风空心砖Ventilating brick耐火砖Fire brick高耐火砖High duty fire clay brick特级粘土耐火粘土砖Super-duty fire clay brick轻质耐火粘土砖Light weight fire clay brick工字钢底砖Clip tile (brick)矿渣砖Slag brick多孔砖Porous brick瓦Tile屋面瓦Roof tile石板瓦Slate陶土瓦Vitrified tile粘土瓦Clay shingle脊瓦Ridge tile斜沟瓦Vallay tile槽形瓦Grooved tile石棉瓦Asbestos tile方块毛石Square rubble条石、块石Block stone花岗石Granite花岗石饰面板Granite finishing plank大理石Marble大理石板Marble slab人造大理石Artificial marble预制水磨石Precast terrazzo砌块Block混凝土砌块Concrete block加气混凝土砌块Aerated concrete block实心砌块Solid block空心砌块Hollow block耐火砌块Refractory block衬里砌块Bushing block玻璃Glass光学玻璃Optical glass防眩光玻璃Anti-dazzle glass耐热玻璃Heat resisting glass隔声玻璃Sound proof glass平板玻璃Plate glass标准玻璃Standard glass抛光平板玻璃Polished plate glass中空玻璃Double glazing glass双层中空玻璃Glazing glass, insulating glass 浮法玻璃Float glass新釉面玻璃Neo-ceramic glass有机玻璃Organic glass钢化玻璃Armourplate glass强化玻璃Strengthened glass磨光玻璃Abrades glass, polished glass 毛玻璃Obscured glass, frosted glass 夹丝安全玻璃Wired glass无色玻璃White glass不透明玻璃Opaque glass漫射玻璃Diffusing glass波形玻璃Corrugated glass槽形玻璃Channel glass淬火玻璃Heat treated glass薄膜玻璃Film glass兰色玻璃Blue glass琥珀色玻璃Amber glass中性灰色滤光玻璃Neutral-tinted glass乳色玻璃Opalescent glass乳白玻璃Opal glass压花玻璃Patterned glass酸蚀刻玻璃Acid-etched glass大理石玻璃Marbled glass磨沙玻璃Ground glass雪花玻璃Alabaster glass玻璃纤维板Glass fiber board钢Steel碳素钢Carbon steel低（中、高）碳钢Low (medium, high) carbonsteel结构钢Structural steel高强度结构钢High-strength structural steel 普通碳素结构钢Ordinary carbon structuralsteel铸钢Cast steel耐酸钢Acid-resisting steel型钢Shaped steel圆钢Round steel bar热轧圆钢Hot rolled round steel扁钢Flat steel bar角钢Angle steel方钢Square steel槽钢Channel steel冷轧碳素钢板Cold rolled carbon steel plate 波纹钢板Corrugated steel花纹钢板Reliefed steel plate不锈钢管Stainless steel pipe焊接钢管Welded steel pipe无缝钢管Seamless steel pipe镀锌钢管Galvanized steel pipe高强度钢丝High strength steel wire绑扎用钢丝Binding wire冷拨低碳钢丝Cold drawn mild steel wire钢筋Steel bar, steel reinforcement 铸件管Cast iron pipe铸铁给水管Cast iron water pipe铸铁污水管Cast iron soil pipe铜Copper黄铜Brass铝Aluminum铅Lead锡Bin镍Nickel锌Zinc螺栓Bolt螺孔直径Diameter of bolt hole垫板Packing垫片Spacer锚固螺栓Anchor bolt现场安装螺栓Field bolt safety nut安全螺帽Safety nut地脚螺栓Holding-down bolt, groundbolt调整螺栓Adjusting nut平头螺栓Cheese head bolt源头螺栓Botton head bolt夹紧螺栓Clinch bolt埋头螺栓Countersunk bolt防松螺帽Self-locking nut带销螺栓头Bolt head with feather柳钉Rivet螺丝Screw垫圈Washer平垫圈Flat washer弹簧垫圈Spring washer防松垫圈Lock washer胶合板Plywood纤维板Fiber board聚合物Polymer高分子化合物High-molecular compound树脂Resin环氧树脂Epoxy resin聚乙烯Polyethylene (PE)聚录乙烯Polyvinyl chloride (PVC)聚苯乙烯Polystyrene聚脂树脂Polyester resin聚丙烯Polyropylene发泡聚案脂Foamed polyurethane建筑及结构设计规范Code for architectural andstructural design施工及验收规范Code for construction andacceptance建筑抗震设计规范Building seismic design code 建筑材料标准Standard for buildingmaterials地基及基础规范Code for soil and foundation 防火规范Fire-protection code卫生标准Sanitary standard电气设计及装置规范Code for electrical design andinstallation给排水规范Code for water supply anddrainage供暖及通风设计及装置规范Code for heating and ventilating design and installation工艺Technology工艺流程图Process flow chart运输流程图Transport flow chart加工图Process technology drawing 工艺设备平面布置图Process equipment layout装配图Assembly drawing人流Person flow物流Goods flow产品大纲Product program生产线Production line生产能力Production capacity年生产量Annual yield, annual output工作制度Work system组织机构表Organization chart工艺对建筑的要求Process requirements onbuildings设计Design设计单位Designer用户Client大学University工厂Factory公司Company有限公司Company limited (Ltd)集团公司、总公司Corporation研究所Research institute设计文件Design document设计资料Design data设计任务书Design prospectus设计说明书Design instruction设计范围Design scope设计周期Design period设计程序Design procedure方案投标Scheme tender方案比较Scheme comparison审批Approval设计阶段Design stage可行性研究（报告）Feasibility study方案设计Initial design初步设计Preliminary design施工图设计Final design设计修改Design modification设计联络Design liaison合同Contract签定合同Sign contract协议、协定Agreement会议纪要Minutes of meeting施工单位Constructor承包单位Contractor供货单位Supplier施工监理Construction supervisor工地经理Site manager职务名称Title董事长﹑院长President总经理General manager总工程师General engineer主任、处长Department manager总设计师Chief designer项目经理Project manager主任工程师Chief engineer工程师Engineer图纸Drawing总平面图General plan布置图Layout工艺专业有关词汇Words concerning technology 工艺Technology工艺过程Process工艺过程设计Process design设备平面布置Plant design工艺要求Technological level电子产品Electronic product半导体Semiconductor电子管Electron tube二级管Diode三级管Triode晶体管Transistor集成电路Integrated circuit (IC)大规模集成电路Large scale integration (ofcircuits) (LSI)超大规模集成电路Very large scale integration (ofcircuits) (VLSI)计算机Computer微型计算机Microcomputer微处理机Microprocessor个人计算机Personal computer计算机终端Terminal电子打字机Electronic type writer计算机打印机Computer printer机器人Robot电子游戏机Electronic gamer电视机Television彩色电视机Color TV黑白电视机Black and white TV显象管Kinescope彩色显象管Color kinescope; chromoscope 黑白显象管Monochrome picture tuve录机Radio cassette电子琴Electronic piano微波炉Microwave oven录象机Video recorder电传机Teleprinter传真机Facsimile printer电话单机Telephone电话交换机Telephone exchange光导纤维Optical fiber雷达Radar激光（器）Laser发射机Transmitter天线Antenna声纳（定位器）Sound radar剖面图放大图Section大样图、详图Enlarged detail安装图Installation drawing标准图（定型）Standard drawing示意图Schematic diagram流程图Flow diagram系统图System diagram原理图Principle diagram综合管道平面图General layout of pipingsystem屋面平面图Roof plan立面图、正视图Elevation侧、横、背、正面图Side, back, front elevation 横、纵、局部剖面图Cross, longitudinal, partsection装配图Assembly drawing鸟澉图Bird’s eye view底图Transparent drawing草图Sketch表格和说明Table and instruction图纸目录List of drawings材料表List of material重复使用图纸目录List of repeat drawing说明Instruction建筑物构筑物明细表List of buildings andstructures建筑一览表Schedule of buildings建设单位Client子项工程名称Sub-project日期Date处室Department专业Specialty比例Scale图纸名称Name of drawing图号Drawing No.张数Page quantity张号Page No.编号Code序号Serial No.代号Mark名称Name型号规格Type and specification数量Quantity单位Unit备注Remark设计阶段Stage (of design)物理概念Physical concept长度Length宽度Width高度Height; altitude深度Depth面积Area时间Time速度Speed温度Temperature湿度Humidity功率Power压力Pressure力Force公斤Kilogram (Kg)克Gram (g)吨Ton (t)米Meter (m)厘米Centimeter (cm)毫米Millimeter (mm)平方米Square meter立方米Cubic meter秒Second分Minute时Hour厚度Thickness直径Diameter半径Radius外径Outside diameter内径Inside diameter圆形Circle方形Square立方体Cube椭圆Ellipse重量Weight毛重Gross weight净重Net weight质量Quality规范Regulation; handbook手册handbook设计规范，手册Regulation, handbook fordesign施工安装规范，手册Regulation, handbook forconstruction and installation 验收规范Regulation for acceptance消防规范Regulation for fire fighting环境保护Environment protection设备手册Handbook of equipment材料手册Handbook of material设计基础资料Basic data of design自然条件Natural condition气象Meteorology气候Climate风向Wind direction主导风Prevailing wind水位Water level地下水位Underground water level最大风速Maximum wind speed最高水位Highest water level最低水位Lowest water level冰冻日数Frost duration冰冻深度Frost penetration海拔Above sea level海拔高度Altitude标高Elevation level原地面标高Natural ground elevation设计地面标高Designed ground elevation地坪Ground level室外地坪标高Outdoor ground elevation室内地坪标高Indoor ground elevation室内外高差Difference of elevationbetween indoor and outdoor中心标高Center elevation雷暴日数Number of lightening days地形Topography经度Longitude纬度Latitude土壤Soil回填土Back filled earth相对湿度Relative humidity选厂基础资料Basic data for site selection选厂报告Report of site selection厂址调查Site investigation生产条件Condition of production生产流程Production process生产能力Production capacity班制Shift per day日班Day shift夜班Nightshift工作日Working day假日Vacation我院专业设置Specialist set up in EDRI工艺Technology无线电技术Radio technique机械Mechanical电化学Electro-chemistry元器件Electronic component电真空器件Electric vacuum component总图General plan土建Civil建筑Architecture结构Structure机械Mechanical暖通Heating, ventilation andair-conditioning (HV AC)给排水Water supply and drain气体动力Gas utility环境保护Environment protection非标准设计Design of non-standardproduct电气Electrical供电Power supply电照Power distribution andlighting自动控制Automatic control通信Communication一层First floor二层Second floor三层Third floor夹层Mezzanine技术夹层Technical floor走廊Corridor外廊Open corridor门廊Porch门厅Entrance hall前厅Lobby出口Exit入口Entrance楼梯间Staircase竖井Shaft电梯间Lift shaft电梯Lift; elevator自动扶梯Escalator办公室Office会议室Meeting room会客室，接待室Reception room展览室Display room休息室Lobby阅览室Reading room资料室Reference room实验室Laboratory医务室Clinic衣帽间Cloak room更衣室Locker room厂长室Director’s room经理室Manager’s room秘书室Secretary’s room会计室Counter’s room值班室Duty room助理室Assistant’s room总务室General affairs office 小食堂Lunch room食堂Canteen厨房Kitchen餐厅Dining hall备餐间Food preparation room 茶室Tea room咖啡室Coffee room酒吧Bar卧室Bed room起居室Living room客厅Parlor书房Study浴室Bathroom厕所Toilet男厕Men’s女厕Women’s工艺设备Production equipment 车床Lathe磨床Grinder转床Driller冲床Puncher电锯Electric saw电梯Elevator电炉Electric furnace电弧炉Arc furnace电阻炉Electronic furnace ofresistance type烘箱，干燥机Drier起重机Crab吊车Crane电焊机Shot welder送风机Air-supply fan鼓风机Blast fan排风机Exhaust fan泵Pump扩散泵Diffusion pump装配线Assembly line生产线Production line生产车间Workshops车间Workshop辅助车间Auxiliary shop机械加工车间Machine shop锻工车间Blacksmith shop冲压车间Press shop焊接车间Welding shop电镀车间Electroplating shop钳工车间Fitter shop机修车间Machine repairing shop金工车间Smith shop装配车间Assembly shop;包装车间Packing shop工具间Packing shop维修间Tool room洁净室Maintenance room净化厂房Purification factory微波暗室Anechoic chamber磁屏暗室Magnetic shielding chamber 设计室Design room房间名称Room names底层Ground floor一层First floor公用建筑Public buildings俱乐部Club电影院Cinema礼堂Assembly hall火车站Railway station飞机场Airport汽车站Bus station游泳池Swimming pool运动场Sports ground体育馆Stadium图书馆Library招待所Hostel医院Hospital公寓Apartment宿舍Dormitory宿舍区Living quarters平房Single-story building公用设施Public utilities facilities电话站Exchange station计算机房Computer room空调机房Air conditioning room新风机室Fresh air room水泵房Water pump house压缩机房Compressor room控制室Control room工作平台Working platform空压站Air compressor station变电站Transformer station冷却塔Cooling tower洗涤塔Scrubber热交换站Heat exchanger station污水处理站Sewage treatment station氢氧（发生）站Hydrogen and oxygen(generation) station油库Fuel storage微波站Microwave station锅炉房Boiler house冷冻站Chiller station2. 土建部分总图专业常用词汇Words concerning generalplan厂区Factory area生活区Living area停车场Parking yard车库Garage自行车棚Bicycle shed大门Gate门房Gate house围墙Enclosure wall围栏Fence建筑红线Property line办公楼Office building科研楼Research building食堂Canteen水泵房Water pump station车间Workshop成品库Finished product store旗杆Flag pole广场Square绿化带Greenbelt喷泉Fountain雕塑Sculpture花园Garden道路Road桥Bridge公路Highway铁路Railway弯道Turn建筑面积Building area建筑占地面积Area occupied by building空地Spare space十字路口Cross零点线Zero line斜坡Slope挖方Excavation老土Natural soil原土Original soil换土Earth shift室外管道Outdoor pipeline室外管沟Outdoor trench雨水明沟Rainwater channel排洪沟Flood trench下水道Sewer下水道检查井Sewer manhole明沟Open channel热力管沟Heating trench草坪Lawn树木，乔木Tree灌木Shrub花坛Flower bed防火距离Fire protection distance抗（地）震Aseismatic抗振动Anti-vibration防振动Vibration-proof防爆Explosion proof防酸Acid-proof防尘Dust-proof经济专业有关词汇Words concerning economy 概算Budgetary estimate预算Budget决算Final accounts估算Estimation估价Cost estimate价、费、成本Cost价格Price成本核算Cost keeping投资Investment投资费、基建费Capital cost工程费Construction cost安装费Cost of installation不可预见费Unpredicted cost额外费用Extra cost设备费Cost of equipment单价Unit price出厂价格Factory price市场价格Market price运费Freight关税Customs duty兑换率Foreign exchange人民币Rate of exchange外汇人民币(RMB)外汇兑换卷Foreign exchange certificate 美元U.S. dollar日元Japanese yen港元Hongkong dollar英镑Pound sterling西德马克DM法国法郎 F.F瑞士法郎S.F.荷兰盾H.FL卢布Ruble总图Site plan基址图Site plot总体规划图Master plan位置图Location map发展规划图Development planning长远规划图Long-term planning总平面图及竖向布置图Site plan and verticalarrangement土方工程图Earth-work drawing土方累计图Mass diagram土方累计曲线Mass curve围墙结构构造图Structural construction chartof fence wall道路结构构造图Structural construction chartof road道路纵剖面图Road profile道路横剖面图Cross section of road室外管线平面图Outdoor pipeline plan道路和堆放场构造图Construction of road andstorage yard工厂组成表Factory composition table工厂区划图Factory blocking地形图Topographical map工厂区，工业区Industrial district工业发展区Industrial development area生活区Residential area, living area商业区Commercial area长区面积Site area建筑面积Floor area建筑占地面积Built-up area铺砌面积Paving area使用面积Usable floor area有效面积Effective floor space建筑总面积Total floor area建筑各层面积Floor space of each story容积率Building volume ratio利用系数，利用率Utilization factor方位，朝向Orientation结构面积Structural area通道面积Passage area道路及广场面积Area of roads and plaza建筑系数Building occupationcoefficient绿化系数Landscaping factor建筑密度Building density城市规划City planning住宅区方案Residential district planning 住宅小区Living quarters总建筑基地面积Gross site area人行道Pedestrian-way行车道Traffic line露天堆放场Storage yard街道交叉处的转盘道Turnaround停车区Parking area停车道Parking lane围墙Fence wall钢丝网围墙Wire-net fence绿化地带Green belt草坪Lawn花坛Flower bed旗杆座Flag-pole stand预留发展地Space for furture extension边线，界线Border line建筑红线Red line安全距离Sfety distance防火间隔Fire break纵坐标Ordinate横坐标Abscissa基准点Datum mark水准基点Bench mark地区水准点Regional bench mark标高Level相对标高Relative elevation设计标高Designed elevation室外地面标高Elevation of ground室外道路标高Road level室外散水标高Outdoor water discharge level 室内地坪标高Elevation of indoor grade绝对标高Absolute altitude等高线Contour line道路纵剖面Profile of road道路横剖面Cross section of road道路交叉点标高Elevation of road intersection 高差Elevation difference土方Earth work土方工程量V olume of earthwork土方平衡表Earthwork balance sheet填土高度Height of filling余土Surplus earth缺土Earth to回填Backfill洼地Depression坡度Inclination坡道Ramp阶梯地面Terraced ground中整场地Site leveling运土Transported soil砂石移运Detritus transport人工填土Artificial fill台阶式挖土法Bench method台阶式挖掘Bench excavation平衡挖填Balance of cuts and fills借土挖方Borrow cut借土填方Borrow fill超挖Overbreak超填Overfill挡土板Lagging挡墙，板桩Bulkhead原状土样Undisturbed soil sample重塑土样Remolded sample爆破工程Explosion work管道Pipeline架空管道Overhead piping地下管道Underground piping管道系统Piping system埋管深度Pipe laying depth城市给水City water supply热力管道Heating pipe line工艺管道Process pipe line氧气管道Oxygen pipe line雨水明沟Rainwater channel下水道Sewer下水道检查井Sewer manhole明沟Ditch, open drain涵洞Culvert边沟Gutter截流井Catch basin给水井Feed well集水井Collecting well室外管沟Outdoor trench排洪沟Flood trench建筑Architecture建筑工程说明General notes建筑草图Architectural sketch建筑透视图Perspective室内装修表Room finish schedule建筑阴影（投影）图Architectural shades andshadows建筑渲染图Architectural rendering1号建筑一层平面布置图Fist floor plan, building No.1 屋面平面图Roof plan1号建筑立面图Elevation, building No.11号建筑剖面图Section, building No.1A-A剖面图Section A-A门厅吊顶平面图Entrance hall suspend ceilingplan铝合金门窗，幕墙图Drawing of aluminium door,window and glazing curtainwall1号建筑一层吊顶平面图Suspended ceiling plan, firstwall一层吊顶平面图Suspended ceiling plan电梯井道平面放大图Enlarged plan of elevator shaft 楼梯平面图Stair plan砖墙节点详图Brick wall joint detail统一建筑详图Uniform architectural details 建筑构件表List of architecturalcomponents1号建筑节点详图Joint detail, building No.1办公大楼Office building装配大楼Assembly building配变电站Substation, transformer station 冷冻站Chiller station纯水站Pure water station去离子水站Deionized water station动力站Utility station乙炔发生站Acetylene generation station 压缩空气站Compressor station配气站Gas distribution station煤气发生站Gas generation station热力站Heat energy station液化厂油气站Liquefied petroleum gasstation氧气站Oxygen氮氧站Nitrogen-oxygen station冷却塔Cooling tower微波站Microwave station洗涤塔Scrubber污水处理站Sewage treatment station氢氧发生站Hydrogen and oxygen station 锅炉房Boiler house热交换站Heat exchanger station走廊Corridor外廊Open corridor门廊Porch净化走道Purified corridor参观走道Viewing corridor服务走道Service corridor缓冲走道Buffer corridor门厅Entrance hall前厅Lobby出口Exit入口Entrance雇员入口Employee entrance行政人员入口Staff entrance办公室Office开敞式办公室Open office行政办公室Administration office经理办公室Manager office秘书办公室Secretary office助理办公室Assistant office人事办公室Personnel office财务办公室Financial office会计室Counte r’s room总务室General affair office收发货办公室Receiving and shipping office 会议室Meeting room会客室Reception room展览室Demonstration room医务室Clinic值班室Duty room图书室Library资料室Information center数据中心Data center食堂Canteen厨房Kitchen餐厅Dining room备餐室Food preparation room茶室Tea room咖啡室Coffee room休息室Break room酒吧Bar洗手间Wash room盥洗室Toilet男厕所Men’s女厕所Women’s更衣室Changing room淋浴室Shower room保安中心Security center储存室Store开水间Kettle room实验室Laboratory产品开发实验室Development laboratory维修间Maintenance room仓库Store原材料仓库Raw material store成品仓库Finished product store备件存放间Parts store材料入检Incoming goods inspection发货区Shipping area化学品存放间Chemical store维修备件存放间Maintenance parts store水泵房Water pump room空调设备室Air handling units room电梯间Elevator room锅炉房Boiler room楼梯间Staircase room车间Workshop辅助车间Auxiliary workshop机械加工车间Mechanical process workshop锻工车间Blacksmith shop冲压车间Press shop焊接车间Welding shop电镀车间Electroplating shop;钳工车间Fitter shop机修车间Machine repairing shop金工车间Smith shop装配车间Assembly shop包装车间Packing shop烧结车间Sintering shop工具间Tools room洁净室Clean room净化厂房Purified factory微波暗室Anechoic chamber拉丝区Drawing area耐火构造Fire resisting construction建筑耐火等级Fire resistance rating ofbuilding饿抵抗能够耐火时限Rated fire-resistance duration 耐火极限Limited of fire resistance开间Bay进深Depth柱网Column grid柱列轴线Axis of column row墙Wall外墙external wall内墙Internal wall隔墙Wall partition砖墙Brick wall空斗墙Row lock wall抹面墙Rendered wall空心墙Hollow wall混凝土砌块墙Concrete block wall承重墙Bearing wall非承重墙Non-bearing wall剪力墙Shear wall围护墙Cladding wall挡土墙Earth-retaining wall背墙Back wall胸墙Breast wall地龙墙Sleeper wall幕墙Curtain wall山墙Gable wall女儿墙Parapet砖压顶女儿墙Brick-cap parapet玻璃隔墙Glazed partition隔断Shower stall活动隔断Movable partition防火墙Fire proof wall抗震墙Earthquake resisting wall地面和楼面面层Ground and floor surfacecourse现浇混凝土楼面Cast-in-place concrete floor水泥沙浆楼面Cement mortar floor现浇水磨石楼面Cast-in-site terrazzo floor块料楼面Block flooring砖楼面Brick floor预制混凝土块楼面Precut concrete block floor预制水磨石楼面Precut terrazzo floor人造大理石楼面Manu marble block floor碎拼大理石楼面Filler broken-marble floor缸砖楼面Clinker floor马赛克楼面Mosaic tile floor镶嵌楼面Floor inlaid拼花楼面Mosaic pavement水泥花砖楼面Cement tile floor水泥压光Cement troweled塑料面Plastic floor纤维板楼面Hard board floor胶合板楼面Glued slab floor无缝楼面Jointless floor叠层楼面Laminated floor供形楼面Arched floor抗静电活动地板Anti-static movable floor活动地板支架Support of movable floor有吊顶的楼板Double floor人造石铺面Granolithic finish玻璃钢面Glassfiber floor拼花花岗岩Granite floor地砖Floor tile防滑砖Non-slip tile抗静电铝合金地面Anti-static aluminium alloyfloor地毯Carpet踢脚Skirting木踢脚Wooded skirtingPVC踢脚PVC skirting玻璃钢踢脚Fiber glass skirting水泥踢脚Cement skirting门Door木门Wooded door钢门Steel door钢丝网门Chain ink铁门Iron door玻璃门Glazed door组合门Composite door两面包铁皮门Door clad with sheet iron onboth sides内门Internal door外门External door大门Gate防火门Fire resisting door隔声门Sound proof door保温门Thermal insulation door冷藏门Cooler door太平门Emergency door安全门Exit door防爆门Explosion proof door防护门Protection door屏蔽门Shield door防射线门Rediation resisting door防风砂门Weather tight door密闭门Sealed door泄压门Pressure release door壁橱门Closet door引风门Ventilation door平开门Side hung door单开门Single action door双向门Double action door双扇门Double action door双扇对开门Double hinged door单开或双开弹簧门Single or double acting door 双开弹簧门Swing door推拉门Sliding door竖向推拉门Vertical sliding door隔栅推拉门Sliding grating door折门According door套叠门Telescoping door水平翻门Trap door卷门Rolling door转门Revolving door自动门Automatic door法式门French door固定门Fixed door夹板门Plywood door镶板门Paneled door平板玻璃门Plate glass door隔栅门Grille door百叶门Shutter door连窗门Door with side window空心门Hollow door窗Window木窗Wooded window钢窗Steel window铝合金窗Aluminium alloy window 塑料窗Plastic framed window纱窗Screen window供窗Arch window凸窗Bay window凹窗Bow window圆窗Round window方窗Square window多角窗Canted window无框格窗Sashless window防火窗Fire resisting window隔声窗Sound proof window保温窗Heat insulation window间隔窗Partition window防护窗Protection window安全窗Security window屏蔽窗Shield window防射线窗Rediation resisting window 防风沙窗Weather tight window密闭窗Sealed window泄压窗Pressure release window 换气窗Vent sash假窗Blank window陈列橱窗Display window扩散窗Diffuse window平开窗Side hung window右（左）开平窗Side hung right (left) handwindow内开平窗Inward opening window推拉窗Sliding window垂直推拉窗Vertically sliding window旋转窗Pivoted window自动开窗Automatic window折叠窗Folding window固定窗Fixed window单层窗Single window双层窗Double window三层窗Triple window山墙窗Gable window边窗Side light腰窗Fanlight带窗Continuous window子母扇窗Attached sash window组合窗Composite window落地窗French window带纱扇窗Window with screen sash固定百叶窗Louver window遮阳式窗Awning window卷帘百叶窗Rolling shutter天窗Skylight上框Head边框Jamb中横框Transom中竖框Mullion下框Sill窗框Sash frame上梃Top rail中梃Middle rail下梃Bottow rail边梃Stile风雨板Weather board挡风雨条Weather strip窗帘Window blind窗铁栅Window guard窗插梢Sash bolt拉手Handle铰链Hinge可拆铰链Loose joint。
建筑工地常用语英汉对照
建筑工地常用语英汉对照一、日常用语100句古得依文宁号阿哟？范恩三克哟号度哟度？格赖的土米特哟三克哟外瑞骂吃三克丝哟阿外儿可么东特们身内的闹的哎套伊科斯Q（字母）思咪扫瑞怕的嗯，普利斯（清音）？代次奥如哎特（清音）奈V呃迈恩的沃此哟儿内么？买内么一子李四古得拜嗨V呃奈斯吹P（清音）侃哎嗨儿P哟？普利斯斯币克斯娄雷普利斯斯币克捞德儿爱康特嘿儿哟可利尔雷Pleaepeaklouder.26我听不懂/不知道。
Idon’tundertand/know.爱动特安得斯但的/Nou27等一会儿。
Jutamoment,pleae.扎斯特呃谋们特（清音）普利斯28等等。
Holdon.侯当29我要等多久？HowlonghouldIwait号浪树的爱位特（清音）？30再等5分钟。
Anotherfiveminute.安那啧Fai唔咪你呲31快点儿。
Hurryup.哈瑞阿P32请这边走。
Thiway,pleae.迪斯味普利斯33请跟我来。
Followme,pleae.发娄咪普利斯34我将告诉你路向。
Iwillhowyoutheway.爱威噢授哟啧味35继续前行。
Goahead.够呃嗨的36当心。
Becareful.毕开尔否37这个还是那个？Thioneorthatone迪斯万噢儿代特万？38主要一点。
Jutalittle.扎斯特呃雷头39（菜）够了，谢谢。
Nomore,thankyou.Nou莫尔，三恩克哟40不了，谢谢。
No,thank.Nou三恩克丝41请坐。
Sitdown,pleae.西当普利斯255继续工作。
Keepworking.K一p沃King55天色渐晚。
I t’gettinglate.依次盖听雷特56让我试试。
Letmetry.莱特咪踹57新年快乐。
HappyNewYear.嗨呸牛耶儿58圣诞快乐。
MerryChritma.买瑞克瑞斯么斯59你也快乐。
Theametoyou.啧Sei么吐哟三恩克丝佛哟儿嗨儿P依次迈泊莱热佛盖提特迈恩的哟凸卡么呃雷扫瑞爱佛告特爱么韩格瑞嗨V撒么兴凸义特阿哟凹Ruai特？爱告特呃非V呃哟逆的呃Ruai斯特（清音）威尔旦卡么凸买噢非斯沃特阿哟嘟应？阿哟K瑞贼？威尔阿哟闹？爱么因呃咪挺耗依兹哟儿沃克？埃么背贼闹爱么泰尔的爱逆的凸京克撒么窝特威尔阿哟勾应？凸啧咔帕克凸啧砍替恩83这太脏了。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
结构工程常用词汇英汉对照混凝土：concrete
钢筋：reinforcing steel bar
钢筋混凝土：reinforced concrete（RC）
钢筋混凝土结构：reinforced concrete structure
板式楼梯：cranked slab stairs
刚度：rigidity
徐变：creep
水泥：cement
钢筋保护层：cover to reinforcement
梁：beam
柱：column
板：slab
剪力墙：shear wall
基础：foundation
剪力：shear
剪切变形：shear deformation
剪切模量：shear modulus
拉力：tension
压力：pressure
延伸率：percentage of elongation
位移：displacement
应力：stress
应变：strain
应力集中：concentration of stresses
应力松弛：stress relaxation
应力图：stress diagram
应力应变曲线：stress-strain curve
应力状态：state of stress
钢丝：steel wire
箍筋：hoop reinforcement
箍筋间距：stirrup spacing
加载：loading
抗压强度：compressive strength
抗弯强度：bending strength
抗扭强度：torsional strength
抗拉强度：tensile strength
裂缝：crack
屈服：yield
屈服点：yield point
屈服荷载：yield load
屈服极限：limit of yielding
屈服强度：yield strength
屈服强度下限：lower limit of yield
荷载：load
横截面：cross section
承载力：bearing capacity
承重结构：bearing structure
弹性模量：elastic modulus
预应力钢筋混凝土：prestressed reinforced concrete
预应力钢筋：prestressed reinforcement
预应力损失：loss of prestress
预制板：precast slab
现浇钢筋混凝土结构：cast-in-place reinforced concrete 双向配筋：two-way reinforcement
主梁：main beam
次梁：secondary beam
弯矩：moment
悬臂梁：cantilever beam
延性：ductileity
受弯构件：member in bending
受拉区：tensile region
受压区：compressive region
塑性：plasticity
轴向压力：axial pressure
轴向拉力：axial tension
吊车梁：crane beam
可靠性：reliability
粘结力：cohesive force
外力：external force
弯起钢筋：bent-up bar
弯曲破坏：bending failure
屋架：roof truss
素混凝土：non-reinforced concrete
无梁楼盖：flat slab
配筋率：reinforcement ratio
配箍率：stirrup ratio
泊松比：Poisson’s ratio
偏心受拉：eccentric tension
偏心受压：eccentric compression
偏心距：eccentric distance
疲劳强度：fatigue strength
偏心荷载：eccentric load
跨度：span
跨高比：span-to-depth ratio
跨中荷载：midspan load
框架结构：frame structure
集中荷载：concentrated load
分布荷载：distribution load 分布钢筋：distribution steel 挠度：deflection
设计荷载：design load
设计强度：design strength 构造：construction
简支梁：simple beam
截面面积：area of section 浇注：pouring
浇注混凝土：concreting
钢筋搭接：bar splicing
刚架：rigid frame
脆性：brittleness
脆性破坏：brittle failure。