HP交换机配置手册
HP FlexFabric 11900交换机系列的48口10Gbps SFP+ 光纤接口卡说明书
48-Port 10-GE SFP+ Fiber Interface Card–LSU1TGS48SF9 1 Card identifierThe mark LSU1TGS48SF9 is printed in the upper right corner of the front panel to identify the card.2 SpecificationsTable 1LSU1TGS48SF9 specificationsItem LSU1TGS48SF9Processor MIPS64 (Dual Core), 1GHzPower consumption 164 W to 255 WConnector LCPort quantity Forty-eight SFP+ Ethernet portsInterface transmission speed 10 Gbps, 1 GbpsOptional modules See Table 2 , Table 3 , Table 4Applied to HP FlexFabric 11900 Switch SeriesFor supported SFP+ modules, see the following table.Table 2SFP+ module specificationsProduct code Moduledescription Centralwavelength(nm)Fiberdiameter(μm)Multimode fibermodal bandwidth(MHz × km)MaxtransmissiondistanceJD092B HP X130 10GSFP+ LC SRTransceiver85050/1252000300 m (984.25ft)500 82 m (269.03 ft)400 66 m (216.54 ft)62.5/125200 33 m (108.27 ft)160 26 m (85.3 ft.)JD094B HP X130 10GSFP+ LC LRTransceiver1310 9/125 N/A10 km (6.21miles)JG234A HP X130 10GSFP+ LC ER40kmTransceiver1550 9/125 N/A40 km (24.86miles)For supported SFP+ cable, see the following table.Table 3 Specifications of SFP+ cable Product codeDescription Cable length Cable type DescriptionJD096C HP X240 10G SFP+ SFP+ 1.2m DA Cable 1.2 m (3.94 ft) SFP+ cableUsed forconnecting SFP+ portsJD097C HP X240 10G SFP+ SFP+ 3m DA Cable 3 m (9.84 ft) JG081CHP X240 10G SFP+ SFP+ 5m DA Cable5 m (16.40 ft)For supported SFP modules, see the following table. Table 4 SFP module specificationsProduct codeModule descriptionCentral wavelength (nm)Fiber diameter (μm)Multimode fiber modal bandwidth (MHz*km)Maxtransmission distanceJD089BHP X120 1G SFP RJ45 T TransceiverN/ACategory-5twisted pairN/A100 m (328.08 ft) JD118BHP X120 1G SFP LC SX Transceiver85050/125500550 m (1804.46 ft)400 500 m (1640.42 ft)62.5/125 200 275 m (902.23 ft) 160 220 m (721.78 ft) JD119BHP X120 1G SFP LC LX Transceiver13109/125N/A 10 km (6.21 miles) 50/125500 550 m (1804.46 ft)40062.5/125 500550 m (1804.46 ft)JD061A HP X125 1G SFP LC LH40 1310nm Transceiver 1310 9/125 N/A 40 km (24.86 miles) JD062A HP X120 1G SFP LC LH40 1550nm Transceiver 1550 9/125 N/A 40 km (24.86 miles) JD063B HP X125 1G SFP LC LH70 Transceiver1550 9/125 N/A70 km (43.50 miles)JD103AHP X120 1G SFP LC LH100 Transceiver 1550 9/125 N/A100 km (62.14 miles) JD098B HP X120 1G SFP LC BX10-UTransceiverThe two modules must beused together. Tx: 1310nm Rx: 1490nm9/125 N/A 10 km (6.21 miles)JD099BHP X120 1G SFP LC BX 10-DTransceiverTx: 1490nm Rx: 1310nm9/125 N/A 10 km (6.21 miles)Productcode Module description Centralwavelength(nm)Fiberdiameter(μm)Multimodefiber modalbandwidth(MHz*km)MaxtransmissiondistanceJD113A HP X170 1G SFP LC LH701470 Transceiver1470 9/125N/A70 km (43.50miles)JD114A HP X170 1G SFP LC LH701490 Transceiver1490 9/125N/A70 km (43.50miles)JD115A HP X170 1G SFP LC LH701510 Transceiver1510 9/125N/A70 km (43.50miles)JD116A HP X170 1G SFP LC LH701530 Transceiver 1530 9/125N/A70 km (43.50miles)JD109A HP X170 1G SFP LC LH701550 Transceiver 1550 9/125N/A70 km (43.50miles)JD110A HP X170 1G SFP LC LH701570 Transceiver 1570 9/125N/A70 km (43.50miles)JD111A HP X170 1G SFP LC LH701590 Transceiver 1590 9/125N/A70 km (43.50miles)JD112A HP X170 1G SFP LC LH701610 Transceiver 1610 9/125N/A70 km (43.50miles)3 Obtaining documentationFor card installation, see HP FlexFabric 11900 Switch Series Installation Guide.For software upgrade, see HP FlexFabric 11900 Switch Series Software Upgrade Guide.To find related documents, browse to the Manuals page of the HP Business Support Center website: /support/manuals© Copyright 2012 Hewlett-Packard Development Company, L.P.The information in this document is subject to change without notice.5998-4094。
HP交换机主要配置
test(config)# ip default-gateway 10.0.6.1 //设置默认网关
方式2:
test(config)# vlan 600 ip address 10.0.6.8 255.255.255.0 //设置管理地址
test(config)# ip default-gateway 10.0.6.1 //设置管理地址
3、设置管理员用户账户和密码
test# configure
test(config)# password manager user-name admin //设置用户名
New password for Manager: ******** //输入密码password
Please retype new password for Manager: ******* //确认输入password
4、配置VLAN
test(config)#vlan 600 tagged 1-3 //给1-3口打上vlan600的tag
1、配置主机名
test(config)# hostname test
2、配置管理IP
方式1:
test(config)# VLAN 600
test(vlan-600)# IP ADDress 10.0.6.8 255.255.255.0 //设置管理地址,管理VLAN为600
test(config-con0)#password MD5 12345678
test(config-con0)#login
8、配置telnet密码
testconfig)#line telnet 0 4
HP交换机简明使用手册
HP交换机简明使用手册HP5400/5300及HP26002006/10目录HP交换机简明使用手册 (1)第一章交换机的初始配置 (4)1.1使用CONSOLE口进行交换机的配置 (4)1.2使用TELNET或者WEB方式对交换机进行配置 (6)1.2.1使用TELNET方式对交换机进行配置 (6)1.2.2通过WEB方式对交换机进行配置 (6)1.3 设置用户名及密码 (7)1.4 配置SNMP相关信息 (8)1.5 LLDP配置 (9)1.6密码恢复方法 (11)1.7 交换机映像更新及配置文件备份与恢复 (11)1.将配置文件备份到TFTP服务器上 (11)2.将从TFTP服务器上的配置文件恢复到交换机 (12)3.升级交换机的映象文件 (12)第二章二层相关协议设置 (13)2.1端口的命名方式 (13)2.2端口物理参数配置 (13)1.设置端口的工作模式 (14)2.对端口的流量进行限制 (14)2.3 802.1qVLAN的基本概念 (15)2.4基于端口的VLAN划分方法 (15)2.5 GVRP的配置 (16)2.6 TRUNKING(LAG)的配置 (17)2.7 生成树的基本概念(STP/RSTP)及配置方法 (17)2.7.1.生成树的基本概念 (17)2.7.2.生成树的配置方法 (19)2.8 实验 (20)一、演示设备架构 (20)二、基本操作命令 (21)三、演示配置 (22)1、5304xl (22)2、2626_1 (23)3、2626_2 (24)4、测试结果 (24)第三章第三层相关设置 (25)3.1 VLAN间路由的配置 (25)3.2 静态路由的配置 (25)3.3 RIP路由协议基本概念 (26)3.4 RIP的配置 (26)3.5 OSPF路由协议的基本概念 (29)3.6 OSPF的配置 (30)3.7路由重分发 (31)3.8 VRRP/XRRP配置 (32)3.9 DHCP Relay 的配置 (34)第四章安全与认证 (36)4.1端口安全性(MAC绑定) (36)4.2访问控制表 (37)4.2.1标准访问控制列表 (37)4.2.2扩展访问控制表 (37)4.4 802.1X认证(OPEN VLAN) (37)4.5 WEB认证 (39)4.6 MAC认证 (40)4.7病毒抑制的原理与配置 (40)第五章组播协议 (42)5.1组播基本概念 (42)5.2 IGMP的配置 (42)5.3 PIM的配置 (42)附件A:5400交换机的许可证安装与删除 (44)第一章 交换机的初始配置1.1使用CONSOLE口进行交换机的配置1.超级终端配置如下:开始-附件-通讯-超级终端,在COM口属性的窗口中选择还原默认值。
Hp交换机操作手册中文版
第一章交换机的初始配置1.1 使用 CONSOLE 口进行交换机的配置 1.超级终端配置如下:开始-附件-数据位: 2.配置好超级终端后,回车登陆。
H P 系列产品默认需要认证,才能进行管理配置,默认的用户名为空,口令为空。
图:此时将进入登陆模式,登陆模式的符号是一个大于号“>”,在此模式下可以实现基本的状 态查看功能,通过问号“?”可以查看此状态下所有可操作的命令.HP 系列产品所有模式下(登陆模式,管理模式和配置模式)均有这种帮助功能,同时 在输入命令时,可以通过<tab>键进行命令补足.登陆模式:以“>”开头,仅仅能够进行一些基本状态查看管理模式:以“#”开头,能够进行所有状态信息的查看,同一时刻允许有多个管 理员处在此模式下。
从登陆模式进入管理模式的命令:en able (可简写为 e n ),通过 enab le 口令 认证后,即可进入管理模式。
配置模式:以“(con fig)”开头,能够对设备进行配置和管理,同一时刻仅仅允许一个管理人员处在配置模式下。
此模式下可以同时具有管理模式和登陆模式的功能。
从管理模式进入配置模式的命令为:conf igur e,即可进入配置模式。
从高级模式退出到低级模式的命令为exi t或disa b le。
3.基本命令1、查看操作系统版本及硬件信息⓿系统当前版本:⓿系统C P U类型:⓿系统内存容量:⓿系统启动时间:⓿系统当前时间:⓿系统端口类型:⓿系统序列号:⓿系统当前能实现的功能:2.配置主机名:实例:例如需要配置设备的名称为B lue,则命令如下。
ip de fault-gate way<ip-a ddress>B lue(c onfi g)#ip def ault-gat eway192.168.0.1H P系列产品提供了P ing和tra cero ute来检查网路的联通状况p ing命令示例:Blue(config)#pi ng192.168.0.1T racer out e命令示例:Blue(config)#tr aceroute192.168.10.11.2使用TELNET或者WEB方式对交换机进行配置1.2.1使用TELNET方式对交换机进行配置1.配置CLI接口访问语法:show conso le下面图例显示交换机缺省的控制台,串口的配置信息:接口访问允许/禁列出事件值和类型控制台控制选项语法:[no]tel net-server语法:Procurv e(config)#no telnet-s erver语法:Procurv e(config)#t elnet-serv er语法:Procurv e(config)#t elnet192.168.2.351.2.2通过WEB方式对交换机进行配置语法:[no]web-management语法:Procurv e(config)#no web-mana gement语法:Procurv e(config)#w eb-managem ent可以后如下图所示:1.3设置用户名及密码1.通过CLI方式配置用户名和密码对于一个企业的安全来说保密是非常重要的。
HP A5810-48G 交换机数据手册说明书
HP A5810-48G Switch Data sheetProduct overviewThe HP A5810-48G Switch delivers unparalleled QoS across 48 10/100/1000Base-T Ethernet ports, two multiplex Gigabit Ethernet (GbE) combination SFP ports, and two 10-GbE SFP+ ports for the most demanding enterprise network environments.Key featuresHigh performance for core and distribution "Flex chassis": modular/stackable in onePowerful IPv4/IPv6 ACL/QoS/VoQPowerful buffer capability—24M bufferingRedundant, hot-swappable power supplies, fansFeatures and benefitsManagement•Remote configuration and management: is available through a secure Web browser or a command-line interface (CLI)•IEEE 802.1ab LLDP discovery: advertises and receives management information from adjacent devices on a network•USB support:–File copy: allows users to copy switch files toand from a USB flash drive•DHCP options: client allows automatic setting of IP address•sFlow: provides scalable, ASIC-based, network monitoring and accounting; this allows network operators to gather a variety of sophisticated network statistics and information for capacity planning and real-time network monitoring purposes •SNMPv1, v2c, and v3: facilitate centralized discovery, monitoring, and secure management of networking devicesConnectivity•Auto-MDIX: automatically adjusts forstraight-through or crossover cables on all 10/100 and 10/100/1000 ports•Jumbo frames: on Gigabit and 10-Gigabit ports, allow high-performance remote backup and disaster-recovery services•High-density port connectivity: provides10/100/1000 port configurations up to 80 ports, and an Intelligent Resilient Framework (IRF) stack of up to 576 10/100/1000 portsPerformance•Hardware-based wire-speed access control lists (ACLs): feature-rich ACL implementation (TCAM based) helps ensure high levels of security and ease of administration without impacting network performanceManageability•RMON (remote monitoring): provides advanced monitoring and reporting capabilities for statistics, history, alarms, and events•Web interface: allows configuration of the switch from any Web browser on the network•Multiple configuration files: allow multiple configuration files to be stored to flash image •Troubleshooting: ingress and egress port monitoring enable network problem solvingLayer 2 switching•16K MAC address table: provides access to many Layer 2 devices•4094 port-based VLANs: provide security between workgroups•Gigabit Ethernet port aggregation: allows grouping of ports to increase overall data throughput to a remote device•10 GbE port aggregation: allows grouping of ports to increase overall data throughput to a remote device•Spanning Tree/MSTP, RSTP, and STP Root Guard: prevent network loopsLayer 3 services•Address Resolution Protocol (ARP): determines the MAC address of another IP host in the same subnet; supports static ARPs; gratuitous ARP allows detection of duplicate IP addresses; proxy ARP allows normal ARP operation between subnets or when subnets are separated by a Layer 2 networkLayer 3 routing•Layer 3 IP routing:–Static IP routing: provides basic routing(supporting up to 1K static routes); allows manual configuration of routingSecurity•Port security: allows access only to specified MAC addresses, which can be learned or specified by the administrator•Advanced processor queuing mechanism: helps prevent denial-of-service (DoS) attacks, while DHCP snooping helps ensure that devices can only receive an IP address from a legitimate DHCP server on the network•IEEE 802.1X-based dynamic delivery of QoS, ACLs, and VLANs: allows complete control over user network access•MAC-based authentication: allows or denies access to the switch based on client MAC address•IP source guard: helps prevent IP spoofing attacks•HTTPS management: provides secure Web management•RADIUS/HWTACACS: eases switch managementsecurity administration by using a passwordauthentication server•Secure Shell (SSHv2): encrypts all transmitteddata for secure, remote command-line interface (CLI)access over IP networksConvergence•LLDP-MED: is a standard extension thatautomatically configures network devices, includingLLDP-capable IP phonesMonitor and diagnostics•Port mirroring: enables traffic on a port to besimultaneously sent to a network analyzer formonitoringAdditional information•Green IT and power: use the latest advances insilicon development, shut off unused ports, and usevariable-speed fans to improve power efficiencyWarranty and support•Lifetime warranty: for as long as you own theproduct with advance replacement andnext-business-day delivery (available in mostcountries)*•Electronic and telephone support: limitedelectronic and telephone support is available fromHP; refer to /networking/warranty fordetails on the support provided and the periodduring which support is available•Software releases: refer to/networking/warranty for details onthe software releases provided and the periodduring which software releases are available foryour product(s)*Hardware warranty replacement for as long as you own the product, with next business day advance replacement (available in most countries) with a five-year hardware warranty replacement for the disk drive included with HP AllianceONE Services zl Module, HP Threat Management Services zl Module, HP PCM+ Agent with AllianceONE Services zlSpecificationsHP A5810-48G Switch (JF242A)Ports48 RJ-45 auto-negotiating 10/100/1000 ports (IEEE 802.3 Type 10Base-T, IEEE 802.3u Type 100Base-TX, IEEE 802.3ab Type 1000Base-T)2 SFP 100/1000 Mbps ports2 SFP+ fixed 1000/10000 SFP+ ports; Duplex: full only1 RJ-45 serial console portPower supplies 2 power-supply slots1 minimum power-supplies required (ordered separately)Physical characteristicsDimensions16.54(d) x 17.32(w) x 1.72(h) in. (42 x 44 x 4.36 cm) (1U height)Weight17.64 lb. (8 kg)Memory and processor512 MB SDRAM, 512 MB flash; packet buffer size: 24 MBMounting Mounts in EIA-standard 19 in. telco rack or equipment cabinet (hardware included)PerformanceThroughput up to 101 million ppsRouting/Switching capacity136 GbpsMAC address table size16,000 entriesEnvironmentOperating temperature32°F to 113°F (0°C to 45°C)Operating relative humidity10% to 90%, non-condensingElectrical characteristicsMaximum heat dissipation614 BTU/hr (647.77 kJ/hr)Voltage100-120 / 200-240 VACFrequency50 / 60 HzSafety UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser Products-Part 2; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; Anatel;ULAR; GOST; EN 60950-1/A11; FDA 21 CFR Subchapter J; NOM; ROHS ComplianceEmissions VCCI Class A; EN 55022 Class A; ICES-003 Class A; ANSI C63.4 2003; AS/NZS CISPR22 Class A; EN 61000-3-2:2006; EN 61000-3-3:1995+A1:2001+A2:2005; EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class AImmunityGeneric ETSI EN 300 386 V1.3.3EN EN 55024:1998+ A1:2001 + A2:2003ESD EN 61000-4-2; IEC 61000-4-2Radiated EN 61000-4-3; IEC 61000-4-3EFT/Burst EN 61000-4-4; IEC 61000-4-4Surge EN 61000-4-5; IEC 61000-4-5Conducted EN 61000-4-6; IEC 61000-4-6Power frequency magnetic field IEC 61000-4-8; EN 61000-4-8Voltage dips and interruptions EN 61000-4-11; IEC 61000-4-11Harmonics EN 61000-3-2, IEC 61000-3-2Flicker EN 61000-3-3, IEC 61000-3-3Management IMC - Intelligent Management Center; command-line interface; Web browser; out-of-band management; SNMP Manager; Telnet; HTTPS; RMON1; FTPNotes A5810 switch provides a power module when shipped. Customer can select two power modules to implement 1+1 power supply redundancy.Services3-year, 4-hour onsite, 13x5 coverage for hardware (UV882E)3-year, 4-hour onsite, 24x7 coverage for hardware (UV885E)3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support (UV888E)3-year, 24x7 SW phone support, software updates (UV891E)4-year, 4-hour onsite, 13x5 coverage for hardware (UV883E)4-year, 4-hour onsite, 24x7 coverage for hardware (UV886E)4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (UV889E)4-year, 24x7 SW phone support, software updates (UV892E)5-year, 4-hour onsite, 13x5 coverage for hardware (UV884E)5-year, 4-hour onsite, 24x7 coverage for hardware (UV887E)5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (UV890E)5-year, 24x7 SW phone support, software updates (UV893E)3 Yr 6 hr Call-to-Repair Onsite (UW969E)4 Yr 6 hr Call-to-Repair Onsite (UW970E)5 Yr6 hr Call-to-Repair Onsite (UW971E)Specifications (continued)HP A5810-48G Switch (JF242A)Refer to the HP website at /networking/services for details on the service-level descriptions and product numbers. For details about services andresponse times in your area, please contact your local HP sales office.Standards and protocols General protocolsIEEE 802.1ag Service Layer OAMIEEE 802.1D MAC BridgesIEEE 802.1p PriorityIEEE 802.1Q VLANsIEEE 802.1s (MSTP)IEEE 802.1v VLAN classification by Protocol andPortIEEE 802.1w Rapid Reconfiguration of SpanningTreeIEEE 802.1X PAEIEEE 802.3ad Link Aggregation Control Protocol(LACP)IEEE 802.3ae 10-Gigabit EthernetIEEE 802.3x Flow ControlRFC 768 UDPRFC 792 ICMPRFC 793 TCPRFC 826 ARPRFC 854 TELNETRFC 925 Multi-LAN Address ResolutionRFC 951 BOOTPRFC 1519 CIDRRFC 1542 BOOTP ExtensionsRFC 2131 DHCPRFC 3576 Ext to RADIUS (CoA only)RFC 4675 RADIUS VLAN & Priority MIBsIEEE8021-PAE-MIBIEEE8023-LAG-MIBRFC 1213 MIB IIRFC 1493 Bridge MIBRFC 2011 SNMPv2 MIB for IPRFC 2013 SNMPv2 MIB for UDPRFC 2233 Interface MIBRFC 2273 SNMP-NOTIFICATION-MIBRFC 2571 SNMP Framework MIBRFC 2572 SNMP-MPD MIBRFC 2573 SNMP-Notification MIBRFC 2618 RADIUS Client MIBRFC 2620 RADIUS Accounting MIBRFC 2665 Ethernet-Like-MIBRFC 2674 802.1p and IEEE 802.1Q Bridge MIBRFC 2688 MAU-MIBRFC 2819 RMON MIBRFC 2925 Ping MIBRFC 3414 SNMP-User based-SM MIBRFC 3415 SNMP-View based-ACM MIBRFC 3418 MIB for SNMPv3RFC 3826 AES for SNMP's USM MIBRFC 4133 Entity MIB (Version 3)LLDP-EXT-DOT1-MIBLLDP-EXT-DOT3-MIBLLDP-MIBNetwork managementIEEE 802.1AB Link Layer Discovery Protocol (LLDP)RFC 2819 Four groups of RMON: 1 (statistics), 2(history), 3 (alarm) and 9 (events)RFC 3176 sFlowANSI/TIA-1057 LLDP Media Endpoint Discovery(LLDP-MED)SNMPv1/v2c/v3SecurityIEEE 802.1X Port Based Network Access ControlRFC 1492 TACACS+RFC 2865 RADIUS (client only)RFC 2866 RADIUS AccountingSecure Sockets Layer (SSL)SSHv2 Secure ShellHP A5810-48G Switch accessories© Copyright 2010 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an To learn more, visit /networkingTransceiversHP X124 1G SFP LC LH40 1310nm Transceiver (JD061A)HP X120 1G SFP LC LH40 1550nm Transceiver (JD062A)HP X125 1G SFP LC LH70 Transceiver (JD063B)HP X110 100M SFP LC LH40 Transceiver (JD090A)HP X110 100M SFP LC LH80 Transceiver (JD091A)HP X130 SFP+ LC SR Transceiver (JD092B)HP X130 SFP+ LC LRM Transceiver (JD093B)HP X130 SFP+ LC LR Transceiver (JD094B)HP X110 100M SFP LC FX Transceiver (JD102B)HP X125 1G SFP LC SX Transceiver (JD118B)HP X120 1G SFP LC LX Transceiver (JD119B)HP X110 100M SFP LC LX Transceiver (JD120B)HP X240 SFP+ SFP+ 0.65 m Direct Attach Cable (JD095B)HP X240 SFP+ SFP+ 1.2 m Direct Attach Cable (JD096B)HP X240 SFP+ SFP+ 3 m Direct Attach Cable (JD097B)CablesNEW HP 0.5 m PremierFlex OM3+ LC/LC Optical Cable(BK837A)Power SupplyHP A5800 300W AC Power Supply (JC087A)Fan TrayHP A5800 1RU Spare Fan Assembly (JC098A)。
惠普 HP ProCurve Switch 1700系列 交换机 说明书
抗干扰性 EN ESD 辐射 EFT/脉冲 电涌 导电 电源频率磁场 电压突降与中断 谐波 闪动 管理 备注
HP ProCurve Switch 1700-24 (J9080A)
22个自适应10/100端口(IEEE 802.3 Type 10Base-T、IEEE 802.3u Type 100Base-TX);介质类型:Auto-MDIX;双工:半双工或全双工
HP ProCurve Switch 1700系列
功能和优势
业界知名的保修服务
监控和诊断
• 端口镜像:使端口上的流量可以同时发送到网络分析器,以便进 行监控
易用性
• 带端口指示器的综合LED显示屏:可以一目了然地查看状态、活 动、速度和全双工运行情况
恢复能力和高可用性
• ProCurve/IEEE Auto-MDIX:自动适应所有10/100/1000端口上 的直连或交叉电缆
惠普网络“网”者之选
重要功能 • 可Web化管理第2层10/100交换机 • 8端口和24端口机型 • 可静音运行的无风扇交换机 • 2个mini-GBIC双功能定制插槽(J9080A) • 业界知名的保修服务
产品技术资料
HP ProCurve Switch 1700系列
HP ProCurve Switch 1700系列包括2款可Web化管理的10/100无风扇交换机,特别适合从非网管连接转移到可网 管网络的企业。HP ProCurve Switch 1700-24是一款24端口交换机,配有22个10/100端口和2个双功能定制端 口。HP ProCurve Switch 1700-8是一款小外形交换机,配有7个10/100端口和1个10/100/1000端口。此外, ProCurve Switch 1700 系列还可以在不增加复杂性的前提下带来更多网络功能。
HPGG刀片交换机配置
HP 6125G/XG交换机配置1、HP 6125G/XG 以太网刀片交换机- 概述 (2)产品描述 (2)产品特性 (2)2、HP 6125G/XG 以太网刀片交换机- 确认组件 (4)前视图 (4)3、HP 6125G/XG 以太网刀片交换机- 规格 (5)系统规格 (5)组件规格 (5)物理规格 (6)电气规格 (6)环境规格 (6)网络布线规格 (6)支持的标准 (7)安全认证 (9)4、HP 6125G 以太网刀片交换机- VLAN 配置命令vlan (9)5、HP 6125G 以太网刀片交换机- VLAN 配置命令shutdown (10)6、HP 6125G 以太网刀片交换机- VLAN 配置命令reset counters interface vlan-interface (11)7、HP 6125G 以太网刀片交换机- VLAN 配置命令name (11)8、HP 6125G 以太网刀片交换机- VLAN 配置命令ip address (11)9、HP 6125G 以太网刀片交换机- VLAN 配置命令interface vlan-interface (12)10、HP 6125G 以太网刀片交换机- VLAN description 配置命令 (13)11、HP 6125G 以太网刀片交换机- VLAN 配置命令display vlan (14)12、HP 6125G 以太网刀片交换机- VLAN display interface vlan-interface 配置命令 .. 1513、HP 6125G 以太网刀片交换机- 以太网端口loopback-detection per-vlan enable 配置命令 (18)14、HP 6125G 以太网刀片交换机- 以太网端口loopback-detection interval-time 配置命令 (18)15、HP 6125G 以太网刀片交换机- 以太网端口loopback-detection enable 配置命令1916、HP 6125G 以太网刀片交换机- 以太网端口loopback-detection control enable 配置命令 (19)17、HP 6125G 以太网刀片交换机- 以太网端口loopback-detection action 配置命令2018、HP 6125G 以太网刀片交换机- 以太网端口Loopback 配置命令 (21)19、HP 6125G 以太网刀片交换机- 以太网端口Interface 配置命令 (22)20、HP 6125G 以太网刀片交换机- 以太网端口Flow-Interval 配置命令 (22)21、HP 6125G 以太网刀片交换机- 以太网端口Flow-Control 配置命令 (23)22、HP 6125G 以太网刀片交换机- 以太网端口Speed Auto 配置命令 (23)23、HP 6125G 以太网刀片交换机- 以太网端口Speed 配置命令 (25)24、HP 6125G 以太网刀片交换机- 以太网端口Duplex 配置命令 (25)25、HP 6125G 以太网刀片交换机- 接口批量配置命令 (26)26、HP 6125G 以太网刀片交换机- Smart Link配置命令 (28)27、HP 6125G 以太网刀片交换机- Monitor Link配置命令 (36)1、 HP 6125G/XG 以太网刀片交换机 - 概述产品描述 产品特性 兼容产品 重要链接 产品描述HP 6125G/XG c-Class BladeSystem 端口、口,本。
HP交换机配置手册(免费下载)
交换机配置手册
Байду номын сангаас 目
第一章 1.1 1.2
录
HP 交换机简明使用手册................................................................................................................ 1 交换机的初始配置 ...................................................................................................... 4 使用 CONSOLE 口进行交换机的配置 ....................................................................... 4 使用 TELNET 或者 WEB 方式对交换机进行配置................................................... 6 1.2.1 使用 TELNET 方式对交换机进行配置 ............................................................. 6 1.2.2 通过 WEB 方式对交换机进行配置........................................................... ......... 6 1.3 设置用户名及密码 .................................................................................... .................... 7 1.4 配置 SNMP 相关信息
惠普Procurve以太网交换机配置指南-Version-1.0
中国惠普有限公司2011年5月5日惠普ProCurve 以太网交换机安装配置指南 Version1.0惠普ProCurve 以太网交换机安装配置指南中国惠普有限公司安装规划中心产品介绍ProCurve 6120系列交换机分为两种型号:●6120G/XG●6120XG产品名称的规则:以6120产品的G/XG为例,G和XG都指端口速率,其中G表示1Gb per second,XG表示10Gb per second;”/”以前的部分特指内部端口速率,”/”以后的部分特指外部端口速率。
前面板及端口介绍:端口•10GbE CX4—The CX4 interface requires the use of copper cabling, similar to the variety used in InfiniBand technology, and is designed to work up to a distance of 15 m. CX4 technology is an attractive solution because it has the lowest cost per port of all 10Gb interconnects, at the expense of range. CX4 has a bigger form factor than either SFP or SFP+.•10GbE XFP ports—These 10GbE ports support SR (multi-mode fiber, 300 m) and LR (single-mode fiber, 10 km) optic transceivers based on the XFP version of the small form factor pluggable specification.XFP transceivers have a smaller form factor compared to several standards (XENPAK, X2, XPAK) that preceded it. The XFP ports support Industry Standard Servers (ISS) optics only.•1GbE SFP ports—These 1GbE ports support SX (multi-mode fiber, 550 m) and LX (single-mode fiber, 10 km) optic transceivers basedon the SFP version of the small form factor pluggable specification using an LC physical connector. These ports also support 1000BASE-T copper connections using an RJ-45 connector. The SFP ports support ISS and ProCurve optics.•10/100/1000 RJ-45 ports—These ports support standard RJ-45 Ethernet cables and each port can operate at one of three autosensing speeds.•5x 10GbE SFP+ ports—These five ports are dedicated10GbE SFP+ ports that support SR (multi-mode fiber, 300 m), LR (single-mode fiber, 10 km), and LRM (multi-mode fiber, 220 m) optic SFP+ transceivers.•2x 10GbE SFP+ ports—Individually, the two ports labeled 23 and 24 can be used as either external 10GbE SFP+ ports or internal 10GbE switch-to-switch (cross-link) ports. For SFP+ connectivity, these ports support the same fiber optic transceivers as the other SFP+ ports.•Internal Network Ports—The 6120G/XG also has “internal”Ethernet ports that function as downlinks to devices in the enclosure. The internals ports are essentially communication interfaces used to transfer data to and from server blades, storage blades, and even another 6120G/XG (if it is installed in an adjacent bay of the enclosure). The internal ports use the enclosure’smidplane circuitry to communicate with the other c-Class enclosure components.•Management Port—The IP address within the OA subnet that you assign to the blade switch is used by a switch component known as Out-Of-Band Management (OOBM).交换机系统指示灯:Module status LED:绿色表示交换机工作正常;橙色表示有故障Module locator LED:用户可以通过命令chassislocate <off|on|blink>来控制其状态,方便用户找到此交换机端口指示灯介绍:Link status LED:绿色表示已连接;橙色表示有故障Link activity LED绿色闪烁表示正在通讯RJ-45指示灯绿色闪烁表示端口正在10/100Mb per second速率通讯橙色闪烁表示端口正在1000Mb per second速率通讯管理口介绍:Mini USB接口,交换机产品包装里都有对应的线缆;使用其管理交换机时,需要先安装相应的驱动程序,并通过终端模拟器软件访问。
HP ProCurve Switch 5400zl、3500yl和 6200yl系列交换机 说明书
技术概述HP ProCurve Switch 5400zl 、3500yl 和6200yl 系列目录摘要 (4)简介 (4)产品定位 (5)概述 (5)HP ProCurve Switch 5400zl 和3500yl 系列 (6)HP ProCurve Switch 6200yl-24G-mGBIC (6)ProVision ASIC 架构 (6)ProVision ASIC 架构内部 (7)分类和查找 (7)策略实施引擎 (8)网络交换机引擎的可编程性 (8)矩阵接口 (8)ProVision ASIC CPU (9)矩阵ASIC (9)管理子系统 (9)产品系列的高级功能 (9)多功能智能端口(VIP) (9)ProVision 硬件弹性 (9)HP ProCurve Switch 5400zl 系列 (10)5400zl 机箱布局 (11)5412zl 机箱布局 (12)电源..................................................................................................................................12 惠普网络“网”者之选风扇托盘 (14)zl模块 (15)管理模块 (15)线路接口模块 (15)电源配置 (17)规格 (19)管理模块 (19)线路接口模块 (20)HP ProCurve Switch 3500yl系列 (25)规格 (26)附加的线路接口模块 (26)HP ProCurve Switch 6200yl (27)附加的线路接口模块 (28)特性与优点概述 (29)性能 (29)安全特性 (29)QoS功能 (30)融合 (30)第2层交换 (31)桥接协议 (31)路由协议 (31)IPv6 (31)组播协议 (31)高可用性和冗余 (31)管理 (32)诊断 (32)适应未来需求 (32)低拥有成本 (32)标准和协议 (33)设备管理 (33)通用协议 (33)IP组播 (33)IPv6 (34)MIB (34)网络管理 (34)OSPF (35)QoS/Cos (35)安全性 (35)性能与容量 (35)容量与性能比较 (35)每端口缓冲区大小 (36)路由和转发表 (36)优化10-GbE端口配置 (36)吞吐率和延迟性能数据 (38)万兆性能流量模式 (40)吞吐率测试 (40)延迟测量 (40)HP ProCurve保修与支持 (41)业界知名的保修服务 (41)附录A:Premium许可 (42)智能边缘和Premium许可 (42)附录B:策略实施引擎 (44)策略实施引擎的优点 (45)ACL的线速性能 (45)附录C:Power over Ethernet (46)PoE设备类型 (46)供电选项 (47)PoE协商 (47)附加的PoE电源 — 外置电源 (47)支持802.3af准标准用电设备 (48)附录D:PIM稀疏模式 (48)附录E:LLDP-MED (49)附录F:病毒遏制安全性 (50)响应选项 (52)灵敏度 (52)连接速率ACL (52)附录G:VRRP (52)5300xl交换机上的XRRP支持 (53)附录H:OSPF等价多路径 (54)附录I:基于高级分类器的QoS (55)附录J:服务器到交换机分布式汇聚 (56)局限/限制 (56)附录K:故障排除 (57)5400zl系列的LED状态指示灯 (57)3500yl和6200yl系列的LED状态指示灯 (60)部件号及现场可更换单元 (62)更多信息 (64)摘要HP ProCurve Networking拥有多种围绕HP ProCurve适应性边缘架构™(AEA)概念而构建的网络产品。
DS-3E0106HP 100Mbps 远程PoE交换机用户手册说明书
2345Device ConnectionConnect your devices according to your actual networking requirements.InterfacesRear PanelFront PanelPacking List1Switch x 1Quick StartGuide x 1Power Cord x 1Hi-PoE PortHi-PoE port is used for other Hi-PoE PTZ cameras connection, and the max. power is 60 W .1/2 PortsHigh priority ports, can guarantee prior and stable transmission .PoE Ports100 Mbps PoE ports are used for other PoE devices connection .RJ45 Ports100 Mbps RJ45 ports are used for device connection via network cables .LINK/ACT Indicator PoE Indicator PoE-MAX Indicator PWRIndicatorPoE Ports RJ45 PortsGrounding TerminalPower SupplyLINK/ACTIndicator Power Adapter x 1Applicable ModelsThis manual is applicable to DS-3E0106HP series 100 Mbps Long-Range PoE switch.Symbol ConventionsThe symbols that may be found in this document are defined as follows.During the installation and utilization of the device, please strictly conform to electrical safety rules in different nations and regions.Use the attached power adaptor only and not to change the adaptor randomly. Please refer to specification table for specific requirements of power adaptor.Never attempt to disassemble the device yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.)The device must be installed in machine room only, and only maintenance staff or qualified person should access to the device.Do not touch the upper cover area of the device that may be overheated.Power must be shut down during cable connection, device installation and dismantlement.You shall acknowledge that the use of the device with Internet access might be under network security risks, please strengthen protection for your personal information and data security. If you find the device might be under network security risks, please contact with us.Proper configuration of all passports and other security settings is the responsibility of the installer, and you shall keep user name and passports properly.Please keep all original packing materials properly. If the product does not work properly, pack the switch in its original packing materials for shipping. We shall not assume any responsibility for damages caused by improper packing materials during shipping.Ensure that your devices powered via the PoE port have their shells protected and fire-proofed, because the switches are not compliant with the Limited Power Source (LPS) standard.This is a class A product and may cause radio interference in which case the user may be required to take adequate measures.Indicates a hazard with a high level of risk, which if not avoided, will result in death or serious injury.SymbolDescriptionProvides additional information to emphasize or supplement important points of the main text.Indicates a potentially hazardous situation, which if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results.•••••••••••DIP SwitchON : Extend mode, ports 1-4 support network transmission of up to 300 m, and the speed rate of the port is 10 Mbps.OFF : Standard mode, the network transmission of PoE ports is up to 100 m, and the speed rate of the port is 100 Mbps.Grounding TerminalThe grounding terminal is used to connect to the ground cable to protect the switch from lightning.Power SupplyUse the attached power cord to connect the switch to socket.If any accessories are damaged or lost, keep the package intact and contact your dealer for replacement.DIP Switch4-Port 10/100M PoE10/100M Unmanaged PoE Pro-SeriesDS-3E0106HP4-Port 100 Mbps Long-Range PoE SwitchQuick Start GuideUD13637B-A678Power-On CheckingSee the following table and check whether your devices are correctly connected. After proper connection, you can use your switch without doing any settings.The switch supports auto MDI/MDIX of ports, you can usestraight-through cable or crossover cable to connect the switch and opposite Ethernet devices.Regulatory InformationFCC InformationPlease take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.FCC ConditionsThis device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:1. This device may not cause harmful interference.2. This device must accept any interference received, including interference that may cause undesired operation.EU Conformity StatementThis product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, the LVD Directive 2014/35/EU,the RoHS Directive 2011/65/EU.2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For properrecycling,returnthis product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points.For more information see: 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb),or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: Industry Canada ICES-003 ComplianceThis device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.Quick Start GuideCOPYRIGHT ©2019 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED.Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”). This user manual (hereinafter referred to be “the Manual”) cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties, guarantees or representations, express or implied, regarding to the Manual.About this ManualThe Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version in the company website (/en/).Please use this user manual under the guidance of professionals.Trademarks Acknowledgementand other Hikvision’s trademarks and logos are the properties of Hikvision in various jurisdictions. Other trademarks and logos mentioned below are the properties of their respective owners.Legal DisclaimerTO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKEANY RESPONSIBILITES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.。
HPE OfficeConnect 1620 交换机系列概述说明书
QuickSpecs HPE OfficeConnect 1620 Switch SeriesOverviewHPE OfficeConnect 1620 Switch SeriesModelsHPE OfficeConnect 1620 8G Switch JG912A HPE OfficeConnect 1620 24G Switch JG913A HPE OfficeConnect 1620 48G Switch JG914AKey features•Entry-level, smart managed layer 2 switches•8-, 24-, and 48-port gigabit models are rack mount capable with included hardware•8- and 24 port models run quiet (fanless)•All models include internal power supplies•Limited Lifetime WarrantyProduct overviewHPE OfficeConnect 1620 Switch Series are entry configurable switches for small business networking, a step up from unmanaged devices, with features to enhance network security, performance and reliability. The series is part of the OfficeConnect portfolio of Hewlett Packard Enterprise small business networking products.These Gigabit switches are plug-and-play out of the box, yet network operations can be fine-tuned through features available from a simple Web browser-based GUI, if necessary. Enhance security using virtual LANs, link aggregation, or IGMP Snooping boost uplink performance, and loop prevention enhances network reliability..The series consists of 8-, 24-, and 48-port 10/100/1000BASE-T models each providing non-blocking gigabit per port performance. All models can be rack mounted and include the necessary rack-mounting hardware; the 8-port model can also be wall mounted. All models come with internal power supplies and localized power cord removing the need to manage externalpower adapters. The 8- and 24-port models are fanless for silent operation.HPE OfficeConnect 1620 Switch Series is covered by a limited lifetime warranty.Features and benefitsManagement•Simple Web managementallows for easy management of the switch even by nontechnical users through an intuitive Web GUI; supports HTTP and HTTP Secure (HTTPS)•Secure Web GUIprovides a secure, easy-to-use graphical interface for configuring the switch via HTTPS.•SNMPv1, v2c, v3facilitates management of the switch, as the device can be discovered and monitored from an SNMP management station.•Port mirroringenables traffic on a port to be simultaneously sent to a network analyzer for monitoring.•Default DHCP client modeallows the switch to be directly connected to a network, enabling plug-and-play operation; in absence of a DHCP server on the network, the switch will fall back to a unique static address determined by the switch's MAC address.•Network Time Protocol (NTP)synchronizes timekeeping among distributed time servers and clients; keeps timekeeping consistent among all clock-dependent devices within the network so that the devices can provide diverse applications based on the consistent time.•Manual network time configurationmanually set the date and time on the switch in the absence of a NTP server.•Dual flash imagesprovides independent primary and secondary operating system files for backup while upgrading •Limited CLIenables users to quickly deploy and troubleshoot devices in the network.Quality of Service (QoS)•IEEE 802.1p prioritization with DSCPdelivers data from the switch to devices based on the priority and type of traffic using Differentiated Services Code Point (DSCP).•Broadcast controlallows limitation of broadcast traffic rate to cut down on unwanted network broadcast traffic.•Rate limitingsets per-port ingress enforced maximums and per-port, per-queue minimums.Connectivity•Auto-MDI/MDIXautomatically adjusts for straight-through or crossover cables on all ports.•IEEE 802.3X flow controlprovides a flow throttling mechanism propagated through the network to prevent packet loss at a congested node.•Loopback detectionif the switch detects a loop, it disables the source port from forwarding data packets originating from the switch to avoid broadcast storms.•Energy Efficient Ethernetcompliant with IEEE 802.3az standard requirements to save energy during periods of low data activity.•Port power save modeenables a port to operate at the lowest transmission speed or go down during a specific time range on certain days of a week. The port resumes when the effective time period ends.•Cable testperforms a check on the status of the cable connected to an Ethernet port on the device. The test determines whether a short circuit or open circuit is present on the cable and the approximate length to the fault in the cable. Performance•Half-/full-duplex auto-negotiating capability on every portdoubles the throughput of every port.•IGMP snooping, v1, v2 and v3improves network performance through multicast filtering, instead of flooding traffic to all ports.Layer 2 switching•VLAN support and taggingsupports IEEE 802.1Q with 4096 simultaneous VLAN IDs.•Jumbo frame supportsupports up to 10 kilobyte frame size to improve the performance of large data transfers.Resiliency and high availability•Link aggregationgroups together multiple ports (up to a maximum of eight ports per trunk) automatically using Link Aggregation Control Protocol (LACP), or manually, to form an ultra-high-bandwidth connection to the network backbone; helps prevent traffic bottlenecks. NOTE:8 port model support 4 trunks, 24 port model support 8 trunks, and the 48 port model support 16 trunks.Warranty and support•Limited Lifetime WarrantySee /officeconnect/support for warranty and support information included with your productpurchase.Build To Order: BTO is a standalone unit with no integration. BTO products ship standalone are not part of a CTO or Rack-Shippable solution.HPE OfficeConnect 1620 8G Switch JG912A•8 RJ-45 autosensing 10/100/1000 ports •1U - Height See ConfigurationNOTE:1PDU Cable NA/MEX/TW/JP JG912A#B2B •C15 PDU Jumper Cord (NA/MEX/TW/JP)PDU Cable NA/MEX/TW/JP JG912A#B2C •C15 PDU Jumper Cord (ROW)High Volt Switch/Router to Wall Power Cord JG912A#B2E •NEMA L6-20P Cord (NA/MEX/JP/TW)HPE OfficeConnect 1620 24G Switch JG913A•24 RJ-45 autosensing 10/100/1000 ports •1U - Height See ConfigurationNOTE:1PDU Cable NA/MEX/TW/JP JG913A#B2B •C15 PDU Jumper Cord (NA/MEX/TW/JP)PDU Cable NA/MEX/TW/JP JG913A#B2C •C15 PDU Jumper Cord (ROW)High Volt Switch/Router to Wall Power Cord JG913A#B2E •NEMA L6-20P Cord (NA/MEX/JP/TW)HPE OfficeConnect 1620 48G Switch JG914A•48 RJ-45 autosensing 10/100/1000 ports •1U - Height See ConfigurationNOTE:1PDU Cable NA/MEX/TW/JP JG914A#B2B •C15 PDU Jumper Cord (NA/MEX/TW/JP)PDU Cable NA/MEX/TW/JP JG914A#B2C •C15 PDU Jumper Cord (ROW)High Volt Switch/Router to Wall Power Cord JG914A#B2E •NEMA L6-20P Cord (NA/MEX/JP/TW)Configuration Rules:Note 1 Localization (Wall Power Cord) required on orders without #B2B, #B2C (PDU Power Cord) or #B2E.(See Localization Menu)Page 4Internal Power SuppliesPower supplies includedRemarks Drop down under power supply should offer the following options and results:Switch/Router/Power Supply to PDU Power Cord - #B2B in North America, Mexico, Taiwan, andJapan or #B2C ROW. (Watson Default B2B or B2C for Rack Level CTO)Switch/Router/Power Supply to Wall Power Cord - Localized Option (Watson Default for BTO andBox Level CTO)High Volt Switch/Router/Power Supply to Wall Power Cord - #B2E Option. (Offered only in NorthAmerica, Mexico, Taiwan, and Japan)HPE OfficeConnect 1620 8G Switch (JG912A)I/O ports and slots8 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: fullonlyAdditional ports and1 RJ-45 console port to access limited CLI portslotsPhysical characteristics Dimensions10.47(w) x 6.38(d) x 1.73(h) in (26.59 x 16.21 x 4.39 cm) (1U height)Weight 2.2 lb (1 kg)Memory and processor MIPS @ 500 MHz, 32 MB flash, 128 MB SDRAM; packet buffer size: 512 KBMounting and enclosure Mounts in an EIA standard 19-inch telco rack or equipment cabinet (hardware included), wall mount Performance100 Mb Latency< 7 µs1000 Mb Latency< 5 µsThroughput up to 11.9 Mpps (64-byte packets)Switching capacity16 GbpsMAC address table size8192 entriesReliability MTBF (years)138.89Environment Operating temperature32°F to 104°F (0°C to 40°C)Operating relative5% to 95%, noncondensinghumidityNonoperating/Storage-40°F to 158°F (-40°C to 70°C)temperatureNonoperating/Storage5% to 95%, noncondensingrelative humidityAltitude up to 16,404 ft (5 km)Acoustic No FanElectrical characteristics Frequency50/60 HzVoltage100 - 240 VAC, ratedMaximum power rating7 WNotes Maximum power rating and maximum heat dissipation are the worst-casetheoretical maximum numbers provided for planning the infrastructurewith fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and allmodules populated.Safety IEC 60950-1; EN 60950-1; CSA 22.2 60950-1; UL 60950-1 2nd EditionEmissions FCC part 15 Class A; VCCI Class A; EN 55022 Class A; CISPR 22 Class A; EN 55024; EN 61000-3-2 2000, 61000-3-3; ICES-003 Class AServices Refer to the Hewlett Packard Enterprise website at /networking/services for details on the service-level descriptions and product numbers. For details about services and responsetimes in your area, please contact your local Hewlett Packard Enterprise sales office.HPE OfficeConnect 1620 24G Switch (JG913A)I/O ports and slots24 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full;1000BASE-T: full onlyAdditional ports and1 RJ-45 console port to access limited CLI portslotsPage 6Physical characteristics Dimensions17.32(w) x 6.81(d) x 1.73(h) in (43.99 x 17.3 x 4.39 cm) (1U height)Weight 4.85 lb (2.2 kg)Memory and processor MIPS @ 500 MHz, 32 MB flash, 128 MB SDRAM; packet buffer size: 4.1 MBMounting and enclosure Mounts in an EIA standard 19-inch telco rack or equipment cabinet (hardware included) Performance100 Mb Latency< 7 µs1000 Mb Latency< 5 µsThroughput up to 35.7 Mpps (64-byte packets)Switching capacity48 GbpsMAC address table size8192 entriesReliability MTBF (years)123.46Environment Operating temperature32°F to 104°F (0°C to 40°C)Operating relative5% to 95%, noncondensinghumidityNonoperating/Storage-40°F to 158°F (-40°C to 70°C)temperatureNonoperating/Storage5% to 95%, noncondensingrelative humidityAltitude up to 16,404 ft (5 km)Acoustic No FanElectrical characteristics Frequency50/60 HzVoltage100 - 240 VAC, ratedMaximum power rating15 WNotes Maximum power rating and maximum heat dissipation are the worst-casetheoretical maximum numbers provided for planning the infrastructurewith fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and allmodules populated.Safety IEC 60950-1; EN 60950-1; CSA 22.2 60950-1; UL 60950-1 2nd EditionEmissions FCC part 15 Class A; VCCI Class A; EN 55022 Class A; CISPR 22 Class A; EN 55024; EN 61000-3-2 2000, 61000-3-3; ICES-003 Class AServices Refer to the Hewlett Packard Enterprise website at /networking/services for details on the service-level descriptions and product numbers. For details about services and responsetimes in your area, please contact your local Hewlett Packard Enterprise sales office.HPE OfficeConnect 1620 48G Switch (JG914A)I/O ports and slots48 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full;1000BASE-T: full onlyAdditional ports and1 RJ-45 console port to access limited CLI portslotsPhysical characteristics Dimensions17.32(w) x 9.37(d) x 1.73(h) in (43.99 x 23.8 x 4.39 cm)Weight7.28 lb (3.3 kg)Memory and processor MIPS @ 650 MHz, 32 MB flash, 128 MB SDRAM; packet buffer size: 512 KB 1.5 MBMounting and enclosure Mounts in an EIA standard 19-inch telco rack or equipment cabinet (hardware included) Performance100 Mb Latency< 7 µs1000 Mb Latency< 5 µsThroughput up to 71.4 Mpps (64-byte packets)Switching capacity96 GbpsMAC address table size16384 entriesReliability MTBF (years)81.30Environment Operating temperature32°F to 104°F (0°C to 40°C)Operating relativehumidity5% to 95%, noncondensingNonoperating/Storagetemperature-40°F to 158°F (-40°C to 70°C)Nonoperating/Storagerelative humidity5% to 95%, noncondensingAltitude up to 16,404 ft (5 km)Acoustic Power: 49.7 dB, Pressure: 49.7 dB; ISO 7779Electrical characteristics Frequency50/60 HzVoltage100 - 240 VAC, ratedMaximum power rating28.2 WNotes Maximum power rating and maximum heat dissipation are the worst-casetheoretical maximum numbers provided for planning the infrastructurewith fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and allmodules populated.Safety IEC 60950-1; EN 60950-1; CSA 22.2 60950-1; UL 60950-1 2nd EditionEmissions FCC part 15 Class A; VCCI Class A; EN 55022 Class A; CISPR 22 Class A; EN 55024; EN 61000-3-2 2000, 61000-3-3; ICES-003 Class AServices Refer to the Hewlett Packard Enterprise website at /networking/services for details on the service-level descriptions and product numbers. For details about services and responsetimes in your area, please contact your local Hewlett Packard Enterprise sales office.Standards and Protocols (applies to all products in series)General protocolsIEEE 802.1D MAC BridgesIEEE 802.1p PriorityIEEE 802.1Q VLANsIEEE 802.3 Type 10BASE-TIEEE 802.3ab 1000BASE-TIEEE 802.3ad Link Aggregation Control Protocol (LACP) IEEE 802.3az Energy Efficient EthernetIEEE 802.3i 10BASE-TIEEE 802.3x Flow ControlDate Version History Action Description of Change:04-Sep-2017 From Version 5 to 6 Changed Updates made on Features and benefits25-Apr-2017 From Version 4 to 5 Changed Minor edit made on Technical Specifications07-Apr-2017 From Version 3 to 4 Changed Minor edit made on Configuration section06-May-2016From Version 2 to 3Changed Document name changed to HPE OfficeConnect 1620Switch Series. SKU descriptions, Overview and TechnicalSpecifications updated.01-Dec-2015From Version 1 to 2Changed Overview and Technical Specifications updatedQuickSpecs HP 1620 Switch series Summary of ChangesSign up for updates© Copyright 2017 Hewlett Packard Enterprise Development LP. The information contained herein issubject to change without notice. The only warranties for Hewlett Packard Enterprise products and services are set forth in the express warranty statements accompanying such products and services.Nothing herein should be construed as constituting an additional warranty. Hewlett Packard Enterpriseshall not be liable for technical or editorial errors or omissions contained herein.To learn more, visit: /networkingc04474819 - 15108 - Worldwide - V6 - 04- September-2017。
hp交换机怎么设置
这个问题对于很多人来说是一个比较难的问题其实交换机的设置与产品的品牌也有关系要视情况而定那么我们平时要怎么设置交换机呢
hp交换机怎么设置
hp交换机怎么设置?以下是小编整理的HPColorLaserJet6015系列word自动双面打印设置方法:
1、在驱动图标上鼠标点击右键,选择“打印机属*”。见图一
2、选择“设备设置”。见图二
3、在“可安装选项”中,找到“双面打印器(用于双面打印)”修改成“已安装”。见图三
4、下找到“允许手动双面打印”,修改成“已禁用”,点击“确定”。见图四
5、打开需要打印的word文档,点击”打印”选项,选择CP6015的打印机,找到“属*”,选择“完成”,将“双面打印”前面的选框勾选上,点击“确定”,进行打印即可。见图五
HP交换机上配置VRF的单一站点部署技术配置指南说明书
Configuring VRF on HP Switches: in a single site deploymentTechnical Configuration GuideVersion:2.1January 2013Table of ContentsTable of Contents (2)Introduction (3)Background Information (3)Requirements (3)Network Diagram (4)Configure (4)Core Device Configuration (4)Configure Core Device Routing (5)Edge Device Configuration (6)Configure Edge Device Routing (7)Demonstration (7)Appendix A – Configurations (7)Core switch configuration (7)Distribution Switch Configuration (11)Server switch configuration (13)Edge switch configuration (15)For more information (17)IntroductionThis Technical Configuration Guide (TCG) describes how to configure Virtual Routing and Forwarding (VRF) in a single site environment. The intended audience is HP Solution Architects, HP Technical Consultants, HP resellers and HP customers.Background InformationCustomer networks have become a critical component in the daily operation of a company. A network outage can result in lost revenue as well as lost productivity from unavailable resources. While some outages are related to failures, most outages are due to a misconfiguration or a small hardware failure, like a NIC card, that has ultimately failed. While most networks employ VLANs to reduce broadcast traffic, there are certain instances where having a VRF are more beneficial. One such instance is when R&D or test labs are connected to the corporate network. Having separate infrastructures is no longer a viable option due to the rising CAPEX and OPEX costs to maintain these standalone networks. By deploying VRFs, these labs are isolated from the corporate network so any failures or misconfigurations can be contained local and not result in a corporate wide outage. VRFs can also provide a level of network security since these lab environments, if compromised, cannot access corporate resources. While some manufacturers, including HP, have released virtualization features that segment out a single physical switch, sometimes the implementation of a switch that has these features is cost prohibitive and typically is limited in scale. VRFs provide another way to accomplish this network segmentation and isolation. RequirementsReaders of this document should be familiar with features and configuration of HP switches.The following hardware is required:•HP Networking switches that support the VRF feature. In this guide a core switch, HP 12500, is used with 5800s and 5820s as the IDF switches.The following software is required:•The latest firmware should be used.The following tools are required:•If a demonstration of the feature is necessary, having a server and some end points as well as access to a traffic generation tool will help demonstrate failure scenarios.Network DiagramFigure 1 illustrates the connectivity for this configuration.Figure 1 VRF Network DiagramConfigureFirst we will configure the core switch since this is really the bulk of the configuration steps. If HP’s IRF technology is to be used, the switches should already be configured with IRF before continuing. Core Device Configuration•Create an IP-VPN instance and Route-Distinguisher (RD)[VRF-Core]ip vpn-instance idf[VRF-Core-vpn-instance-idf]route-distinguisher 100:1[VRF-Core]ip vpn-instance server[VRF-Core-vpn-instance-idf]route-distinguisher 101:1[VRF-Core]ip vpn-instance disti[VRF-Core-vpn-instance-idf]route-distinguisher 102:1The RD is just a distinguishing number used for the routing table and as such can be arbitrary. In this example we will use the transport VLAN for the different VPN-instances.•Create the VLANs that will be used to transport port information between VRFs. You can also at this point create any VLANs that are going to be associated with each VRF or are to be configured on the core device itself.[VRF-Core]vlan 100 to 102[VRF-Core-vlan100]vlan 10 to 20•Create and bind the vlan-interface to each vpn-instance. It is recommended that you configure the IP address after binding the interface since this command removes any previously configured information.[VRF-Core] interface vlan-interface 100[VRF-Core-Vlan-interface100]ip binding vpn-instance idf[VRF-Core-Vlan-interface100]ip address 172.16.100.254 24[VRF-Core] interface vlan-interface 101[VRF-Core-Vlan-interface101]ip binding vpn-instance server[VRF-Core-Vlan-interface101]ip address 172.16.101.254 24[VRF-Core] interface vlan-interface 102[VRF-Core-Vlan-interface102]ip binding vpn-instance disti[VRF-Core-Vlan-interface102]ip address 172.16.102.254 24•Create the bridge aggregation groups that you will be using to connect the IDF, server farm and distribution switches to the core[VRF-Core] interface Bridge-Aggregation100[VRF-Core-Bridge-Aggregation100]port link-type trunk[VRF-Core-Bridge-Aggregation100]port trunk permit vlan 1 10 20100 [VRF-Core-Bridge-Aggregation100]link-aggregation modedynamic[VRF-Core-Bridge-Aggregation100]mad enable•Create the remaining bridge aggregation groups and add the corresponding ports to the groups(CLI commands omitted)Configure Core Device RoutingTo be able to route between VRFs the following steps must be taken. Once configured, all VLANs in all VRFs will be able to communicate. If certain VLANs are to be restricted, route policies must be configured to prevent routing information from being exchanged.[VRF-Core]bgp 65000[VRF-Core-bgp]router-id 1.1.1.1[VRF-Core-bgp]ipv4-family vpn-instance idf[VRF-Core-bgp-idf]peer 172.16.100.252 as-number 65001[VRF-Core-bgp-idf]peer 172.16.100.253 as-number 65001[VRF-Core-bgp-idf]import-route direct[VRF-Core-bgp-idf]quit[VRF-Core-bgp]ipv4-family vpn-instance server[VRF-Core-bgp-server]peer 172.16.101.253 as-number 65002[VRF-Core-bgp- server]import-route direct[VRF-Core-bgp- server]quit[VRF-Core-bgp]ipv4-family vpn-instance disti[VRF-Core-bgp-disti]peer 172.16.102.253 as-number 65003[VRF-Core-bgp- disti]import-route direct[VRF-Core-bgp- disti]quit•The following commands are what allow the exchange of routing information between VRFs. Note that the RD used is that of the vpn-instance you are trying to reach not of the originating vpn-instance.[VRF-Core-vpn-instance-idf]vpn-target 101:1 both[VRF-Core-vpn-instance-idf]vpn-target 102:1 both[VRF-Core-vpn-instance-server]vpn-target 100:1 both[VRF-Core-vpn-instance-server]vpn-target 102:1 both[VRF-Core-vpn-instance-disti]vpn-target 100:1 both[VRF-Core-vpn-instance-disti]vpn-target 101:1 bothEdge Device ConfigurationFor this scenario, the intelligence of VRF is in the core 12500 hardware. Each stackable switchhas minimal configuration.•First configure the VLANs that each device will have locally as well as the transport VLAN for VRF.[vrf-idf01]vlan 10[vrf-idf01]vlan 20[vrf-idf01]vlan 100•Next configure the IP address for each VLAN[vrf-idf01-Vlan-interface100]ip address 172.16.100.253 24[vrf-idf01-Vlan-interface10]ip address 10.1.10.1 24[vrf-idf01-Vlan-interface20]ip address 10.1.20.1 24 •Create the Bridge Aggregation group and add the corresponding ports to the group[VRF-idf01] interface Bridge-Aggregation100[VRF-idf01-Bridge-Aggregation100]port link-type trunk[VRF-idf01-Bridge-Aggregation100]port trunk permit vlan 110 20 100[VRF-idf01-Bridge-Aggregation100]link-aggregation modedynamic[VRF-idf01-Ten-GigabitEthernet1/0/1]port link-type trunk[VRF-idf01-Ten-GigabitEthernet1/0/1]port trunk permit vlan1 10 20 100[VRF-idf01-Ten-GigabitEthernet1/0/1]port link-aggregationgroup 100Configure Edge Device Routing•The final step is to configure BGP on the IDF switch(es). In this example, a static route has been configured to the core. A dynamic routing protocol could be used as well.[VRF-idf01]bgp 65001[VRF-idf01-bgp]peer 172.16.100.254 as-number 65000[VRF-idf01-bgp]quit[VRF-idf01]ip route-static 0.0.0.0 0.0.0.0 172.16.100.254 DemonstrationHere’s an example of a demonstration that can be used to verify this configuration:Introduce a broadcast storm in a VRF to show that it stays localized. Creating a STP Loop isanother effective demo as well.∙If you have access to Ixia test gear, this equipment can generate a broadcast storm at line rate 10G.∙To prove that only the local VRF is affected, streaming video and ICMP requests were monitored in the other VRFs. A physical server in the server VRF can share a folder and laptops in the otherVRFs (IDF and Disti) can play the same video. When there is no broadcast storm, the videos are in sync and play smoothly and there are no ICMP timeouts. When the Ixia test port was enabled and introduced a broadcast storm into a VRF, video degradation was seen only on the laptop in thesame VRF as the Ixia and there were multiple ICMP timeouts. Once the broadcast was eliminated the video resumed playing normally with no ICMP timeouts.∙If test equipment or a traffic generator isn’t available you could use hacking tools like Metasploit and launch a DOS attack or ping of death to achieve similar results.Appendix A – ConfigurationsBelow are the actual configurations from an IRF 12508 core with 5800, 5820 and 5500-EI as edge devices:Core switch configurationsysname CORE12508#irf mac-address persistent always irf auto-update enableundo irf link-delay#domain default enable system#forward-path check enablehardware-failure-detection chipwarning hardware-failure-detection boardwarning hardware-failure-detection forwarding#ip vpn-instance edge route-distinguisher 100:1 vpn-target 101:1 102:1 export-extcommunityvpn-target 101:1 102:1 import-extcommunity#ip vpn-instance server route-distinguisher 101:1 vpn-target 102:1 100:1 export-extcommunityvpn-target 102:1 100:1 import-extcommunity#ip vpn-instance disti route-distinguisher 102:1 vpn-target 101:1 100:1 export-extcommunityvpn-target 101:1 100:1 import-extcommunity#vlan 1#vlan 10#vlan 20#vlan 100 to 102#domain system access-limit disable state active idle-cut disableself-service-url disable#user-group system#interface Bridge-Aggregation100description LAG to Edgeport link-type trunkport trunk permit vlan 1 10 20 100link-aggregation mode dynamicmad enable#interface Bridge-Aggregation101description LAG to Serverport link-type trunkport trunk permit vlan 1 101link-aggregation mode dynamicmad enable#interface Bridge-Aggregation102description LAG to Distiport link-type trunkport trunk permit vlan 1 102link-aggregation mode dynamicmad enable#Interface Bridge-Aggregation110 description LAG to edge_5800_2port link-type trunkport trunk permit vlan 1 10 20 100link-aggregation mode dynamicmad enable#interface NULL0#interface LoopBack0ip address 10.10.10.10 255.255.255.255 #interface Vlan-interface10ip address 10.1.10.254 255.255.255.0#interface Vlan-interface20ip address 10.1.20.254 255.255.255.0#interface Vlan-interface100ip binding vpn-instance edgeip address 172.16.100.254 255.255.255.0 #interface Vlan-interface101ip binding vpn-instance serverip address 172.16.101.254 255.255.255.0 #interface Vlan-interface102ip binding vpn-instance distiip address 172.16.102.254 255.255.255.0 #interface Ten-GigabitEthernet1/2/0/1 port link-type trunkport trunk permit vlan 1 102port link-aggregation group 102#interface Ten-GigabitEthernet1/2/0/2 port link-type trunkport trunk permit vlan 1 102port link-aggregation group 102#interface Ten-GigabitEthernet1/2/0/3 port link-type trunkport trunk permit vlan 1 101port link-aggregation group 101#Configuration omitted for brevityinterface Ten-GigabitEthernet1/2/0/4 port link-type trunkport trunk permit vlan 1 101port link-aggregation group 101#interface Ten-GigabitEthernet1/2/0/5 port link-type trunkport trunk permit vlan 1 10 20 100 port link-aggregation group 100#interface Ten-GigabitEthernet1/2/0/6 port link-type trunkport trunk permit vlan 1 10 20 100port link-aggregation group 110#interface Ten-GigabitEthernet2/2/0/1 port link-type trunkport trunk permit vlan 1 102port link-aggregation group 102#interface Ten-GigabitEthernet2/2/0/2 port link-type trunkport trunk permit vlan 1 102port link-aggregation group 102#interface Ten-GigabitEthernet2/2/0/3 port link-type trunkport trunk permit vlan 1 101port link-aggregation group 101#interface Ten-GigabitEthernet2/2/0/4 port link-type trunkport trunk permit vlan 1 101port link-aggregation group 101#interface Ten-GigabitEthernet2/2/0/5 port link-type trunkport trunk permit vlan 1 10 20 100 port link-aggregation group 100#interface Ten-GigabitEthernet2/2/0/6 port link-type trunkport trunk permit vlan 1 10 20 100port link-aggregation group 110#bgp 65000router-id 1.1.1.1 undo synchronization #ipv4-family vpn-instance edgepeer 172.16.100.252 as-number 65001peer 172.16.100.253 as-number 65001 import-route direct#ipv4-family vpn-instance serverpeer 172.16.101.253 as-number 65002 import-route direct#ipv4-family vpn-instance distipeer 172.16.102.253 as-number 65003preference 20 200 20 import-route direct#user-interface con 1/0 2/1user-interface aux 1/0 2/1user-interface vty 0 4#irf-port 1/1port group interface Ten-GigabitEthernet1/2/0/7 port group interface Ten-GigabitEthernet1/2/0/8 #irf-port 2/2port group interface Ten-GigabitEthernet2/2/0/7 port group interface Ten-GigabitEthernet2/2/0/8 #returnDistribution Switch Configurationversion 5.20, Feature 1208#sysname VRF-Disti#irf mac-address persistent timer irf auto-update enableundo irf link-delay#domain default enable system#telnet server enable#vlan 1#vlan 50#vlan 60#vlan 102#vlan 300#Configuration omitted for brevityBridge-Aggregation12 description LAG to 12500port link-type trunkport trunk permit vlan 1 102link-aggregation mode dynamic#interface NULL0#interface Vlan-interface50ip address 10.1.50.1 255.255.255.0#interface Vlan-interface60ip address 10.1.60.1 255.255.255.0#interface Vlan-interface102ip address 172.16.102.253 255.255.255.0 #interface Vlan-interface300ip address 10.1.30.1 255.255.255.0#interface GigabitEthernet1/0/15port link-mode bridgeport access vlan 50#interface GigabitEthernet1/0/16port link-mode bridgeport access vlan 50#interface GigabitEthernet1/0/17port link-mode bridgeport access vlan 60#interface GigabitEthernet1/0/18port link-mode bridgeport access vlan 60#interface Ten-GigabitEthernet1/0/1port link-mode bridgeport link-type trunkport trunk permit vlan 1 102port link-aggregation group 12#interface Ten-GigabitEthernet1/0/2port link-mode bridgeport link-type trunkport trunk permit vlan 1 102port link-aggregation group 12#interface Ten-GigabitEthernet1/0/4port link-mode bridgeport access vlan 50#bgp 65003router-id 3.3.3.3 import-route direct undo synchronizationpeer 172.16.102.254 as-number 65000#load xml-configuration#user-interface aux 0user-interface vty 0 15#returnServer switch configurationversion 5.20, Feature 1208#sysname VRF-Server#irf mac-address persistent timer irf auto-update enableundo irf link-delay#domain default enable system#telnet server enable#vlan 1#vlan 30#vlan 40#vlan 101#radius scheme system server-type extendedprimary authentication 127.0.0.1 1645primary accounting 127.0.0.1 1646 user-name-format without-domain#domain system access-limit disable state active idle-cut disableself-service-url disable#user-group system#interface Bridge-Aggregation101description Server LAGport link-type trunkport trunk permit vlan 1 101link-aggregation mode dynamic#interface NULL0#interface Vlan-interface30ip address 10.1.30.1 255.255.255.0#interface Vlan-interface40ip address 10.1.40.1 255.255.255.0#interface Vlan-interface101ip address 172.16.101.253 255.255.255.0 #interface GigabitEthernet2/0/15port link-mode bridgeport access vlan 30#interfaceGigabitEthernet2/0/16port link-mode bridgeport access vlan 30#Interface GigabitEthernet2/0/17port link-mode bridgeport access vlan 40#interface GigabitEthernet2/0/18port link-mode bridgeport access vlan 40#interface Ten-GigabitEthernet2/0/1port link-mode bridgeport link-type trunkport trunk permit vlan 1 101port link-aggregation group 101#interface Ten-GigabitEthernet2/0/2port link-mode bridgeport link-type trunkport trunk permit vlan 1 101port link-aggregation group 101#Configuration omitted for brevity#bgp 65002 import-route directundo synchronizationpeer 172.16.101.254 as-number 65000#load xml-configuration#user-interface aux 1user-interface vty 0 15#returnEdge switch configurationversion 5.20, Release 1206#sysname VRF-01#irf mac-address persistent timer irf auto-update enableundo irf link-delay#domain default enable system#telnet server enable#vlan 1#vlan 10 to 15#vlan 100description VRF to MCE#radius scheme system server-type extendedprimary authentication 127.0.0.1 1645primary accounting 127.0.0.1 1646 user-name-format without-domain#domain system access-limit disable state active idle-cut disableself-service-url disable#user-group system#interface NULL0#interface Vlan-interface10ip address 192.168.10.1 255.255.255.0#interface Vlan-interface100ip address 172.16.100.253 255.255.255.0#interface GigabitEthernet1/0/1port link-mode bridgeport access vlan 10#interface GigabitEthernet1/0/2port link-mode bridgeport access vlan 10#interface GigabitEthernet1/0/3port link-mode bridgeport access vlan 10#interface GigabitEthernet1/0/4port link-mode bridgeport access vlan 10#interface GigabitEthernet1/0/5port link-mode bridgeport access vlan 10#interface GigabitEthernet1/0/6port link-mode bridgeport access vlan 10#interface Ten-GigabitEthernet1/0/25port link-mode bridgeport access vlan 100#Configuration omitted for brevityospf 1area 0.0.0.0network 172.16.100.0 0.0.0.255network 192.168.10.0 0.0.0.255#ip route-static 0.0.0.0 0.0.0.0 172.16.100.254 #load xml-configuration#user-interface aux 0user-interface vty 0 15#returnFor more informationTo read more about HP Networking Products, go to /go/networking Share with colleagues Rate this document。
HP交换机基本命令配置
test_5304xl(config)# show rate-limit all
三、基于端口的 VLAN 划分方法
基于端口 VLAN 划分命令
语法:vlan < vid >
4、配置网关
配置网关命令: ip default-gateway<ip-address>
实例:配置一个缺省的网关 Blue(config)# ip default-gateway 192.168.0.1
第二页,共37页。
5、测试网络联通情况
HP 系列产品提供了 Ping 和 traceroute 来检查网路的联通 状况。
一、基本命令
1、超级终端的配置
开始-附件-通讯-超级终端,在 COM 口属性的窗口中选择还原 默认值。
每秒位数(B):9600 数据位(D): 8 奇偶校验(P):无
停止位(S):1
数据流控制(F): 无
2、配置主机名 命令:hostname <name-string>:其中主机名长度最长为 64 字节
test_5304xl(config)# show name
Port Names Port Type Name A1 100/1000T link_web_server
A2 100/1000T Link_client_2
第十页,共37页。
二、端口物理参数配置
1.设置端口的工作模式
显示每个端口的工作模式,使用命令: 语法:show interfaces [ brief | config | < port-list >]
HPE FlexFabric 12910 交换机模块说明书
Manual version: 6P103-20160715 BOM: 3123A0Q0 Part number: 5998-4319R LSX1FAB10B1 Switching Fabric Module(JG623A/JH115A)1 Card identifierThe mark LSX1FAB10B1 is printed at the upper left corner of the front panel, and is used to identifythe card.2 SpecificationsTable 1 LSX1FAB10B1 specificationsItem SpecificationProcessor MIPS64 (Dual Core), 1GHz.SDRAM 2GB DDR3 SDRAM.Power consumption 135 W to 170 W.Compatible device models HPE FlexFabric 12910 Switch.NOTE:•To verify compatibility of the card with the software release you are using, see the release notes.•Before you install the card to the switch, remove the protective box for the card.When you install a switching fabric module, hold the ejector levers of the module with both hands,press the buttons on the ejector levers, and pull the ejector levers outward, and then press theejector levers inward after the module is fully seated into the slot.When you remove a switching fabric module, press the buttons on the ejector levers and pull theejector levers outward, and then pull out the switching fabric module.3 Obtaining documentationFor card installation, see the HPE FlexFabric 12900 Switch Series Installation Guide.For software upgrade, see the HPE FlexFabric 12900 Switch Series Software Upgrade Guide.To access documentation and support services, go to the Hewlett Packard Enterprise SupportCenter website:/support/hpesc5998-4319RThe information in this document is subject to change without notice.© Copyright 2016 Hewlett Packard Enterprise Development LP1。
- 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。
第一章交换机的初始配置1.1 使用 CONSOLE 口进行交换机的配置 1.超级终端配置如下:开始-附件-数据位: 2.配置好超级终端后,回车登陆。
H P 系列产品默认需要认证,才能进行管理配置,默认的用户名为空,口令为空。
图:此时将进入登陆模式,登陆模式的符号是一个大于号“>”,在此模式下可以实现基本的状 态查看功能,通过问号“?”可以查看此状态下所有可操作的命令.HP 系列产品所有模式下(登陆模式,管理模式和配置模式)均有这种帮助功能,同时 在输入命令时,可以通过<tab>键进行命令补足.登陆模式:以“>”开头,仅仅能够进行一些基本状态查看管理模式:以“#”开头,能够进行所有状态信息的查看,同一时刻允许有多个管 理员处在此模式下。
从登陆模式进入管理模式的命令:en able (可简写为 e n ),通过 enab le 口令 认证后,即可进入管理模式。
配置模式:以“(con fig)”开头,能够对设备进行配置和管理,同一时刻仅仅允许一个管理人员处在配置模式下。
此模式下可以同时具有管理模式和登陆模式的功能。
从管理模式进入配置模式的命令为:conf igur e,即可进入配置模式。
从高级模式退出到低级模式的命令为exi t或disa b le。
3.基本命令1、查看操作系统版本及硬件信息⓿系统当前版本:⓿系统C P U类型:⓿系统内存容量:⓿系统启动时间:⓿系统当前时间:⓿系统端口类型:⓿系统序列号:⓿系统当前能实现的功能:2.配置主机名:实例:例如需要配置设备的名称为B lue,则命令如下。
ip de fault-gate way<ip-a ddress>B lue(c onfi g)#ip def ault-gat eway192.168.0.1H P系列产品提供了P ing和tra cero ute来检查网路的联通状况p ing命令示例:Blue(config)#pi ng192.168.0.1T racer out e命令示例:Blue(config)#tr aceroute192.168.10.11.2使用TELNET或者WEB方式对交换机进行配置1.2.1使用TELNET方式对交换机进行配置1.配置CLI接口访问语法:show conso le下面图例显示交换机缺省的控制台,串口的配置信息:接口访问允许/禁列出事件值和类型控制台控制选项语法:[no]tel net-server语法:Procurv e(config)#no telnet-s erver语法:Procurv e(config)#t elnet-serv er语法:Procurv e(config)#t elnet192.168.2.351.2.2通过WEB方式对交换机进行配置语法:[no]web-management语法:Procurv e(config)#no web-mana gement语法:Procurv e(config)#w eb-managem ent可以后如下图所示:1.3设置用户名及密码1.通过CLI方式配置用户名和密码对于一个企业的安全来说保密是非常重要的。
如果不设置密码那么任何人知道IP地址的人都可以通过WEB/CLI/菜单的方式查看和修改交换机的配置。
其后果是非常严重的,所以强烈建议客户设置本地密码和用户名。
只有专人才能控制和管理这台设备。
语法:[no]passwo rd<manager/operator> [user-name ASC II][no]pas sword all>置操作员密码用设置用(操作员只有只读的权限)B lue#configB lue(c onfi g)#password opera tor12345678(密码将显示成:********)12345678为密码12345678(再次输入密码进行校验)置管理员B lue#configB lue(c onfi g)#password manag er usernam e svacomm svacomm为用户名12345678(密码将显示成:********)12345678为密码12345678(再次输入密码进行校验)2.通过WEB方式设置用户名和密码设置操(管理员有完全的读和写的权限)这里有两种访问的权限Read-only access只分配给普通用户权限,而下面的read-write access是分配给管理员的权限。
输入相应的用户名和密码点击A pply Changes按钮保存即可。
客户再次登陆时候会弹出以下窗口,输入相应的用户名和密码就能获得相应的权限。
普通用户可以是没有用户名的。
只输入密码点击O K就可以。
1.4配置SNMP相关信息a.打开SNMP3使用snmp3enable命令。
一个初始用户登陆将会产生MD5验证和DES数据加密。
b.可以限制对SNMP3代理的访问可以使用snmpv3only命令。
同时你也可以限制对1.开启或关闭S NMPV3代理访问交换机,包括建立初始的用户记录。
语法:[no ]sn mpv3 e nabl e语法:[no ]sn mpv3 o nl y语法:[no ]sn mpv3 r estr i cted -a cces s 语法:s h o w sn mpv3 e n a ble语法:s h o w sn mpv3 rest r icted -acce ss以下案例将详细介绍了 S NMPV3 的详细配置:打开 SNMPv3SNMPV3 管理程序建立初始用户模式设 置 限 制 非 SNMPV3 信息。
设置SNMPV3 共同体名称 SNMPV3 共同体允许使用 V1,V2 版本的交换机进行访问。
共同体只能在支持 2C 及 1C 的组接口级别设备上进行映像。
这一映像可在有组件接口授权的设备上自动生成,但特殊映 像必须使用 snmpv3 communty 命令1.5 LLDP 配置IE EE业网络的故障查找变得更加容易,并加强网络管理工具在多厂商环境中发现和保持精确网络 拓扑结构的能力。
链路层发现协议(Link Layer Discovery Protocol ,LLDP )是 802.1ab 中定义的新协议, 它可使邻近设备向其他设备发出其状态信息的通知,并且所有设备的每个端口上都存储着定义自己的信息,如果需要还可以向与它们直接连接的近邻设备发送更新的信息,近邻的设备会将信息存储在标准的SNMP MIBs。
网络管理系统可从MIB处查询出当前第二层的连接情况。
LLDP不会配置也不会控制网络元素或流量,它只是报告第二层的配置。
802.1ab中的另一个内容是使网络管理软件利用LLDP所提供的信息去发现某些第二层的矛盾之处。
IEEE 目前使用的是IETF现有的物理拓扑、接口和Entity MIBs。
简单说来,LLDP是一种邻近发现协议。
它为以太网网络设备,如交换机、路由器和无线局域网接入点定义了一种标准的方法,使其可以向网络中其他节点公告自身的存在,并保存各个邻近设备的发现信息。
例如设备配置和设备识别等详细信息都可以用该协议进行公告。
语法:s h o w lld p co nfig如下图所示:语法:s h o w lld p co nfig<port-list>如下图所示3.打开和禁止LLDP功能。
语法:[no]lld p ru n1.6密码恢复方法如果密码丢失点击交换机面板前的clear按钮。
当点击c lear按钮后将删除交换面的密码和用户名。
可以使用面板上的reset及clear按钮恢复设备的出厂值:同时按住r eset及clear按钮,大约5秒钟后放开reset按钮,继续按住c lear按钮,等面板上的sefltest,放开按钮。
为了保护你交换机的配置安全,建议将交换机放置在安全的场所,不被外人有物理接触。
该按钮的可以使用如下命令行禁止:语法:[no]fro nt-p anel-securi t y p ass w ord-clea r reset-on-clea r1.7交换机映像更新及配置文件备份与恢复1.将配置文件备份到TFTP服务器上语法:copy<star tup-config|r unning-con fig>tftp<ip-addr><remote-file>[pc|un ix]或copy co nfig<filename>tftp<ip-addr><remote-file>[pc|unix]实例:将配置文件备份到一台T FT P服务器上Pro C ur v e#co py sta rtu p-config tft p10.28.227.105d:\conf igs\s w53002.将从TFTP服务器上的配置文件恢复到交换机将交换机的配置备份到远程的TFTP服务器上。
3.升级交换机的映象文件先到网站上下载映象文件。
/rnd/software/switches.htm该站点包含了最新的升级软件。
实例:将TFT P服务器上的映像文件拷贝到交换机上区域:第二章二层相关协议设置2.1端口的命名方式HP5300/5400交换机的面板如下图所示,端口在配置文件中的命名是以槽位/序号的方式进行:以5406为例,槽位编号从左至右,从上到下分别是:A、B、C、D、E、F 如A模块的第一个端口就叫:A1其它的非模块化交换机的端口命名以序号标识:如2626的15个端口就是15给一个端口或一些端口配置一个友好的名字语法:inte rfac e<port-list>na m e<port-nam e-在端口列表中删除实例:给一个端口配置一个名字l in k_w eb_se r v ertest_5304xl(co nfig)#i n t a1n a m e lin k_w eb_ser v ertest_5304xl(co nfig)#s h o w na m ePort N a m esPort Typ e N a m eA1100/1000T l in k_w eb_ser v er2.2端口物理参数配置1.设置端口的工作模式显示每个端口的工作模式,使用命令:查看端口的情况:2.对端口的流量进行限制A4|D isa bled N o-o v errid e2.3802.1qVLAN的基本概念802.1Q VLAN:802.1Q主要定义了V LAN。
VLAN可使属于同一VLAN的设备实现互相访问,使属于不同VLAN间的设备不能互相访问,划分了网络的广播域。
利用VLAN可大大减少网络中不必要的数据交换的数量,提升网络传输性能。