RI-I11-114B-S1中文资料
西威变频器调试资料-中文版
西威变频器调试资料一. 变频器线路说明1。
同步变频器选型方法2。
与常见微机板匹配注意事项(蓝光、新时达、中秀、奔克、里霸)3。
与常用曳引机匹配注意事项(蓝光、欣达、孚信、阿尔法、蒙特纳利、威特）4。
端子与接线说明二。
外部部件说明与选配1。
制动电阻选型2. 滤波器选型3. 编码器与分频卡海德汉hipeface内密控4. 旋转变压器与RES卡三。
操作说明1。
面板操作说明2。
参数修改步骤3。
参数保存方法四。
参数设置表及简要说明五. 变频器自学习调试1。
电流自学习2. 无齿定位自学习六。
速度曲线与时序的说明七. 舒适感调试说明1。
PI调节2。
预转矩调试八。
常见显示错误与处理方法1. 报警清除方法2。
软件报错的说明3。
硬件故障处理方法九。
3.5与3.4新增、改变内容对照表十。
附录1 3.5版本说明十一。
反馈表一。
变频器线路说明1。
同步变频器选型方法当永磁同步无齿曳引机选配变频器型号时,除了要符合曳引机的铭牌参数外，一般还需要满足1.6 Ib>2。
0Ij，的电流公式。
Ib:变频器的额定电流。
Ij：曳引机的额定电流。
2. 与常见微机板匹配注意事项（蓝光、新时达、中秀、奔克、里霸)（未完善）因西威变频器软件系统比较强大,启动时比一般变频器要慢.在电梯系统上电后,变频器正常信号给的比较慢，新时达微机板等会不断的断合变频器电源，从而无法正常运行运行。
具体处理方法：将变频4060号参数置1（反），微机板中Drive OK输入端设为常闭有效。
3。
与常用曳引机匹配注意事项（蓝光、欣达、孚信、阿尔法、蒙特纳利、威特）（未完善) 进口曳引机参数不详，，具体参数要向曳引机销售方咨询。
4. 端子与接线说明（详细参见说明书P50)a、主线路注意事项制动电阻应接在BR1和C之间，不能接在C和D或者D和BR1之间，如果接错会损坏变频器"主线路端子在接线时要拧紧，不然会影响变频器和电机性能，容易产生故障"b、控制线路注意事项采用变频器内部24V时，需要将变频器18、19端子接入回路。
Keysight Technologies P-Series Power Meters and P-
Keysight TechnologiesP-Series Power Meters andP-Series Wideband Power SensorsConfiguration GuideP-Series Power Meters:N1911A Power Meter (single channel)N1912A Power Meter (dual channel)P-Series Power Sensors:N1921A Power Sensor (50 MHz to 18 GHz)N1922A Power Sensor (50 MHz to 40 GHz)IntroductionThis configuration guide describes standard configurations, options and compatible accessories. Contact your local Keysight Technologies, Inc. representative for additional information.P-Series Power MetersThe P-Series power meters provide peak, average, peak-to-average ratio power measurements, time-gated and free run modes, rise time, fall time and pulse width measurements.The P-Series power meters are compatible with the 8480, E-Series and new P-Series power sensors. The P-Series power meters have a different sensor input connector than the EPM and EPM-P Series power meters, so it is necessary to use adapter cables. These adapter cables come in three different lengths. When using the 8480 or E-Series sensors, refer to the Cable Accessories section in this guide. For additional information, refer to the Literature References section.The standard P-Series power meters include:–Single-channel power meter, order N1911A or dual-channel power meter, order N1912A–Input sensor connector(s) on the front panel–Reference calibrator (1 mW, 50 MHz) connector on the front panel–Documentation CD-ROM–Keysight Instrument Control DVD–IO libraries suite–Command expert–BenchVue software platform–30-day free trial of BenchVue power meter/sensor control and analysis app–Supplied accessories: power cord (plug matches country destination requirements)–USB adapter cable (part number 8121-1583, Cable-Assembly 4Pin-5Pin Male USB 2000 mm-LG)P-Series Wideband Power SensorsThe P-Series wideband power sensors are designed specifically for operation with the P-Series power meters for wide bandwidth power and time measurements. These sensors are the only Keysight power sensors that have their cable permanently wired (hard-wired) into the sensor. This provides better wide bandwidth specifications compared to having a removable cable. Refer to the Sensor Cable Lengths section in this guide for part number and cable length information.The standard P-Series power sensors include:–Power sensor 50 MHz to 18 GHz, order N1921A–Power sensor 50 MHz to 40 GHz, order N1922A–Documentation CD-ROM1. The Installation Guide is in English, French, and Japanese languages (part number N1912-90009).CompatibilityPower sensor compatibilityThe P-Series power meters are compatible with all current (N)8480, E-Series andP-Series power sensors. Refer to the Accessories section, P-Series meter cable adaptorsN1917A/B and C.Connector options for P-Series power metersThe following options are available on the P-Series power meters. 1Table 1. Connector options for P-Series power meters.Option DescriptionN1911A-003Rear panel sensor and power reference connectors (single channel)N1912A-003Rear panel sensor and power reference connectors (dual channel)Video output option (H01)The video output provides a DC voltage proportional to the measured input power through a BNC connector on the rear panel. The DC voltage can be displayed on an oscilloscope for time measurement. This option replaces the recorder output on the rear panel. The video output impedance is 50 Ω.–Video rise time: 13 ns–Frequency range: 50 MHz to 40 GHz 21. The P-Series power meters are configured for either front panel connectors (both sensor and powerreference) or rear panel connectors. There are no options for parallel front and rear panel sensor inputs.2. Need to turn off the auto-zero feature; otherwise, this will appear as a glitch in the video output signal.P-Series Power Meter Optional AccessoriesTable 2. P-Series power meter optional accessories.Accessory part number DescriptionN1911A-908N1912A-908Rack mount kit (one instrument)N1911A-909N1912A-909Rack mount kit (two instruments)34131A Basic instrument transit case 34161AAccessory pouchSoftware AccessoriesKeysight BenchVue softwareKeysight BenchVue software for the PC accelerates testing by providing intuitive, multiple instrument measurement visibility and data capture with no programming necessary. You can derive answers faster than ever by easily viewing, capturing and exporting measurement data and screen shots. The N1911A/12A Power Meters are supported by Keysight BenchVue software’s BV0007B Power Meter/Sensor Control and Analysis app.For more information, /find/BenchVueCable AccessoriesPower sensor adapters for use with 8480 and E-Series power sensors:Table 3. Cable accessories for use with 8480 and E-Series power sensors.Accessory part number DescriptionN1917A P-Series meter cable adaptor, 1.5 m (5 ft)N1917B P-Series meter cable adaptor, 3 m (10 ft)N1917CP-Series meter cable adaptor, 10 m (31 ft)P-Series Wideband Power Sensor Cable LengthsThree fixed cable length options are available for the P-Series power sensors at 1.5 m, 3.0 m and 10 m. Option 105 is the standard (default) option.Table 4. P-Series wideband power sensor cable lengths.OptionDescriptionN1921A-105N1922A-105Fixed 1.5 m (5 ft) cable length N1921A-106N1922A-106Fixed 3 m (10 ft) cable length N1921A-107N1922A-107Fixed 10 m (31 ft) cable lengthCalibration OptionThe P-Series power meters and sensors are available with Option 1A7 (ISO17025 compliant calibration) or Option A6J (ANSI Z540 compliant calibration).DocumentationThe P-Series power meters are supplied with a Product Reference CD which contains the installation guide, user’s guide, programing guide and service guide User’s Guide Programming Guide. The following tables supply the option number as well as the Keysight part number (where appropriate) to order the documentation.Table 5. Documentation.Option DescriptionN1911A-0BK N1912A-0BK Additional English language manual set (User’s Guide, part number N1912-90002 and Programming Guide part number N1912-90009)N1911A-0BFN1912A-0BFEnglish-language Programming Guide (part number N1912-90009)N1911A-0BWN1912A-0BWService Guide (part number N1912-90015)N1911A-ABJN1912A-ABJJapanese localization, User’s Guide part number N1912-90007N1921A-0B1 N1922A-0B1Additional English language manual set, Operating and Service Manual, part number N1920-90007Literature ReferencesPublication title Publication number P-Series Power Meters and P-Series Wideband Power Sensors – Technical Overview5989-1049ENN1911A/N1912A P-Series Power Meters and N1921A/N1922A Wideband PowerSensors - Data Sheet5989-2471ENE4416A/E4417A EPM-P Series Power Meters and E-Series E9320 Peak and AveragePower Sensors – Data Sheet5980-1469E EPM Series Power Meters E-Series and 8480 Series Power Sensors - Data Sheet5965-6382E Fundamentals of RF and Microwave Power Measurements (Part 1) - Application Note5988-9213EN Fundamentals of RF and Microwave Power Measurements (Part 2) - Application Note5988-9214EN Fundamentals of RF and Microwave Power Measurements (Part 3) - Application Note5988-9215EN Fundamentals of RF and Microwave Power Measurements (Part 4) - Application Note5988-9216EN4 Steps for Making Better Power Measurements - Application Note5965-8167E Choosing the Right Power Meter and Sensor - Application Note5968-7150EThis information is subject to change without notice.© Keysight Technologies, 2009 - 2018Published in USA, March 7, 20185989-1252ENLearn more at/find/software Start with a 30-day free trial./find/free_trialsDownload your next insightKeysight software is downloadableexpertise. From first simulation through first customer shipment, we deliver the tools your team needs to accelerate from data to information to actionable insight. – Electronic design automation (EDA) software– Application software– Programming environments –Productivity softwareEvolving Since 1939Our unique combination of hardware, software, services, and people can help you reach your next breakthrough. We are unlocking the future of technology.From Hewlett-Packard to Agilent to Keysight.myKeysight/find/mykeysightA personalized view into the information most relevant to you./find/emt_product_registrationRegister your products to get up-to-date product information and find warranty information.Keysight Channel Partners/find/channelpartnersGet the best of both worlds: Keysight’s measurement expertise and product breadth, combined with channel partner /find/powermetersFor more information on KeysightTechnologies’ products, applications or services, please contact your local Keysight office. The complete list is available at:/find/contactus Americas Canada (877) 894 4414Brazil 55 11 3351 7010Mexico001 800 254 2440United States(800) 829 4444Asia Pacific Australia 1 800 629 485China800 810 0189Hong Kong 800 938 693India 1 800 11 2626Japan 0120 (421) 345Korea 080 769 0800Malaysia 1 800 888 848Singapore 180****8100Taiwan0800 047 866Other AP Countries (65) 6375 8100Europe & Middle East Austria 0800 001122Belgium 0800 58580Finland 0800 523252France 0805 980333Germany ***********Ireland 1800 832700Israel 1 809 343051Italy800 599100Luxembourg +32 800 58580Netherlands 0800 0233200Russia 8800 5009286Spain 800 000154Sweden 0200 882255Switzerland0800 805353Opt. 1 (DE)Opt. 2 (FR)Opt. 3 (IT)United Kingdom0800 0260637For other unlisted countries:/find/contactus (BP-9-7-17)。
IL711-1E中文资料
IsoLoop is a registered trademark of NVE Corporation. *U.S. Patent numbers 5,831,426; 6,300,617 and others.REV. QHigh Speed/High Temperature Dual Digital IsolatorsFunctional DiagramsIL711IL712IN 1IN 2OUT 1OUT2OUT 1IN 2OUT 2IN 1Features• +5 V/+3.3 V CMOS / TTL Compatible• High Speed: 150 Mbps Typical (IL711S/IL712S)• High Temperature: −40°C to +125°C (IL711T/IL712T) • 2500 V RMS Isolation (1 min.)• 300 ps Typical Pulse Width Distortion (IL711S/IL712S) • 4 ns Typical Propagation Delay Skew • 10 ns Typical Propagation Delay• 30 kV/μs Typical Common Mode Transient Immunity • 2 ns Channel-to-Channel Skew• 8-pin MSOP, SOIC, and PDIP Packages • UL1577 and IEC 61010-2001 ApprovalApplications• ADCs and DACs • Digital Fieldbus • RS-485 and RS-422• Multiplexed Data Transmission • Data Interfaces• Board-to-Board Communication • Digital Noise Reduction • Operator Interface• Ground Loop Elimination • Peripheral Interfaces •Serial Communication • Logic Level ShiftingDescriptionNVE’s IL700 family of high-speed digital isolators are CMOS devices manufactured with NVE’s patented* IsoLoop ® spintronic GiantMagnetoresistive (GMR) technology. The IL711S and IL712S are theworld’s fastest two-channel isolators, with a 150 Mbps typical data rate for both channels.The symmetric magnetic coupling barrier provides a typical propagation delay of only 10 ns and a pulse width distortion as low as 300 ps (0.3 ns), achieving the best specifications of any isolator. Typical transient immunity of 30 kV/µs is unsurpassed. The IL711 has two transmit channels; the IL712 has one transmit and one receive channel. The IL712 operates full duplex, making it ideal for many fieldbus applications, including PROFIBUS. The IL711 and IL712 are available in 8-pin MSOP, SOIC, and PDIPpackages. Standard and S-Grade parts are specified over a temperature range of −40°C to +100°C; T-Grade parts are specified over a temperature range of −40°C to +125°C.Absolute Maximum RatingsParameters Symbol Min. Typ. Max. Units Test Conditions Storage Temperature T S −55 150 °CAmbient Operating Temperature (1)IL711T/IL712T T A −55 125135 °CSupply Voltage V DD 1, V DD 2 −0.5 7 V Input Voltage V I −0.5 V DD + 0.5 V Output Voltage V O −0.5 V DD + 0.5 V Output Current Drive I O 10 mA Lead Solder Temperature 260 °C 10 sec. ESD 2 kV HBMRecommended Operating ConditionsParametersSymbol Min. Typ. Max. Units Test ConditionsAmbient Operating Temperature IL711/IL712 and IL711S/IL712S IL711T/IL712T T A −40 −40 100 125°C °CSupply VoltageV DD 1, V DD 2 3.0 5.5 V Logic High Input Voltage V IH 2.4 V DD V Logic Low Input VoltageV IL 0 0.8 V Input Signal Rise and Fall Timest IR , t IF 1 μsInsulation SpecificationsParametersSymbol Min. Typ. Max. Units Test ConditionsCreepage Distance MSOP 3.01 mm SOIC 4.03 mm PDIP 7.04mmLeakage Current 0.2 μA 240 V RMS , 60 Hz Barrier Impedance>1014||3Ω || pFPackage CharacteristicsParametersSymbol Min. Typ. Max. Units Test Conditions Capacitance (Input–Output)(5) C I –O 2 pF f = 1 MHz Thermal ResistanceMSOP θJC 168 °C/WSOIC θJC 144 °C/WPDIPθJC 54 °C/WThermocouple at centerunderside of packagePackage Power DissipationP PD150 mW f = 1 MHz, V DD = 5 VSafety and ApprovalsIEC61010-1TUV Certificate Numbers: N1502812, N1502812-101Classification as Reinforced InsulationModel PackagePollution Degree Material Group Max. WorkingVoltage IL711-1; IL712-1 MSOP Pending Approval IL711-2; IL712-2 PDIP II III 300 V RMS IL711-3; IL712-3 SOIC II III 150 V RMSUL 1577Component Recognition Program File Number: E207481 Rated 2500V RMS for 1 minuteSoldering ProfilePer JEDEC J-STD-020C, MSL=2IL711 Pin Connections1 V DD1 Supply voltage2 IN 1 Data in, channel 13 IN 2 Data in, channel 24 GND 1 Ground return for V DD15 GND 2 Ground return for V DD26 OUT 2 Data out, channel 27 OUT 1 Data out, channel 18 V DD2 Supply voltageIN 1IN 2V DD1GND 1OUT 2OUT 1V DD2GND 2IL711IL712 Pin Connections1 V DD1 Supply voltage2 IN 1 Data in, channel 13 OUT 2Data out, channel 2 4 GND 1 Ground return for V DD1 5 GND 2 Ground return for V DD2 6 IN 2 Data in, channel 2 7 OUT 1 Data out, channel 1 8 V DD2 Supply voltageIN 1IN 2V DD1GND 1OUT 2OUT 1V DD2GND 2Timing DiagramLegendt PLH Propagation Delay, Low to High t PHL Propagation Delay, High to Low t PW Minimum Pulse Width t R Rise Time t F Fall Time3.3 Volt Electrical SpecificationsElectrical specifications are T min to T max unless otherwise stated. Parameters Symbol Min. Typ. Max. Units Test ConditionsDC SpecificationsInput Quiescent Supply Current IL711 8 10 μA IL712 I DD11.5 2 mAOutput Quiescent Supply Current IL711 3.3 4 mA IL712 I DD21.5 2 mA Logic Input Current I I −10 10 μAV DD – 0.1 V DD I O = −20 μA, V I = V IH Logic High Output Voltage V OH0.8 x V DD0.9 x V DD V I O = −4 mA, V I = V IH 0 0.1 I O = 20 μA, V I = V IL Logic Low Output Voltage V OL0.5 0.8 V I O = 4 mA, V I = V ILSwitching SpecificationsMaximum Data Rate IL711/IL712 and IL711T/IL712T IL711S and IL712S 100 130 110 140 Mbps MbpsC L = 15 pFC L = 15 pF Pulse Width (7)PW 10 7.5 ns 50% Points, V O Propagation Delay Input to Output (High to Low)t PHL 12 18 ns C L = 15 pF Propagation Delay Input to Output (Low to High)t PLH 12 18 ns C L = 15 pF Pulse Width Distortion (2) IL711/IL712 and IL711T/IL712T IL711S and IL712SPWD2 13 3 ns C L = 15 pF Propagation Delay Skew (3)t PSK 4 6 ns C L = 15 pF Output Rise Time (10%–90%) t R 2 4 ns C L = 15 pF Output Fall Time (10%–90%) t F 2 4 ns C L = 15 pF Common Mode Transient Immunity (Output Logic High or Logic Low) (4) |CM H |,|CM L | 20 30 kV/μs V CM = 300 V Channel-to-Channel Skew t CSK 2 3 ns C L = 15 pFDynamic Power Consumption (6)140 240 μA/MHz per channel Magnetic Field Immunity (8)(V DD2= 3V, 3V<V DD1<5.5V)Power Frequency Magnetic Immunity H PF 1000 1500 A/m 50Hz/60Hz Pulse Magnetic Field Immunity H PM 1800 2000 A/m t p = 8µs Damped Oscillatory Magnetic Field H OSC 1800 2000 A/m 0.1Hz – 1MHzCross-axis Immunity Multiplier (9)K X 2.55 Volt Electrical SpecificationsElectrical specifications are T min to T max unless otherwise stated. Parameters Symbol Min. Typ. Max. Units Test ConditionsDC SpecificationsInput Quiescent Supply Current IL711 10 15 μA IL712 I DD12.5 3 mA Output Quiescent Supply Current IL711 5 6 mA IL712 I DD22.5 3 mA Logic Input Current I I −10 10 μAV DD − 0.1 V DD I O = −20 μA, V I = V IH Logic High Output Voltage V OH0.8 x V DD0.9 x V DD V I O = −4 mA, V I = V IH 0 0.1 I O = 20 μA, V I = V IL Logic Low Output Voltage V OL0.5 0.8 V I O = 4 mA, V I = V ILSwitching SpecificationsMaximum Data Rate IL711/IL712 and IL711T/IL712T IL711S and IL712S 100 130 110 150 Mbps MbpsC L = 15 pFC L = 15 pF Pulse Width (7)PW 10 7.5 ns 50% Points, V O Propagation Delay Input to Output (High to Low)t PHL 10 15 ns C L = 15 pF Propagation Delay Input to Output (Low to High)t PLH 10 15 ns C L = 15 pF Pulse Width Distortion (2) IL711/IL712 and IL711T/IL712T IL711S and IL712SPWD2 0.3 3 3 ns C L = 15 pF Propagation Delay Skew (3) t PSK4 6 ns C L = 15 pF Output Rise Time (10%–90%) t R 1 3 ns C L = 15 pF Output Fall Time (10%–90%) t F 1 3 ns C L = 15 pF Common Mode Transient Immunity (Output Logic High or Logic Low)(4) |CM H |,|CM L | 20 30 kV/μs V cm = 300 V Channel to Channel Skew t CSK 2 3 ns C L = 15 pFDynamic Power Consumption (6)200 340 μA/MHz per channel Magnetic Field Immunity (8)(V DD2= 5V, 3V<V DD1<5.5V)Power Frequency Magnetic Immunity H PF 2800 3500 A/m 50Hz/60Hz Pulse Magnetic Field Immunity H PM 4000 4500 A/m t p = 8µs Damped Oscillatory Magnetic Field H OSC 4000 4500 A/m 0.1Hz – 1MHzCross-axis Immunity Multiplier (9)K X 2.5Notes (apply to both 3.3 V and 5 V specifications):1. Absolute maximum ambient operating temperature means the device will not be damaged if operated under these conditions. It does notguarantee performance.2. PWD is defined as |t PHL − t PLH |. %PWD is equal to PWD divided by pulse width.3. t PSK is the magnitude of the worst-case difference in t PHL and/or t PLH between devices at 25°C.4. CM H is the maximum common mode voltage slew rate that can be sustained while maintaining V O > 0.8 V DD 2. CM L is the maximumcommon mode input voltage that can be sustained while maintaining V O < 0.8 V. The common mode voltage slew rates apply to both rising and falling common mode voltage edges.5. Device is considered a two terminal device: pins 1–4 shorted and pins 5–8 shorted.6. Dynamic power consumption is calculated per channel and is supplied by the channel’s input side power supply.7. Minimum pulse width is the minimum value at which specified PWD is guaranteed.8. The relevant test and measurement methods are given in the Electromagnetic Compatibility section on p. 6.9. External magnetic field immunity is improved by this factor if the field direction is “end-to-end” rather than to “pin-to-pin” (see diagram on p. 6).80 ns Application InformationElectrostatic Discharge SensitivityThis product has been tested for electrostatic sensitivity to thelimits stated in the specifications. However, NVE recommends that all integrated circuits be handled with appropriate care to avoid damage. Damage caused by inappropriate handling or storage could range from performance degradation to complete failure.Electromagnetic CompatibilityIL700-Series Isolators are fully compliant with generic EMC standards EN50081, EN50082-1 and the umbrella line-voltage standard for Information Technology Equipment (ITE) EN61000. The IsoLoop Isolator’s Wheatstone bridge configuration and differential magnetic field signaling ensure excellent EMC performance against all relevant standards. NVE conducted compliance tests in the categories below:EN50081-1Residential, Commercial & Light Industrial Methods EN55022, EN55014 EN50082-2: Industrial EnvironmentMethods EN61000-4-2 (ESD), EN61000-4-3 (Electromagnetic Field Immunity), EN61000-4-4 (Electrical Transient Immunity), EN61000-4-6 (RFI Immunity), EN61000-4-8 (Power Frequency Magnetic Field Immunity), EN61000-4-9 (Pulsed Magnetic Field), EN61000-4-10 (Damped Oscillatory Magnetic Field) ENV50204Radiated Field from Digital Telephones (Immunity Test)Immunity to external magnetic fields is even higher if the fielddirection is “end-to-end” rather than to “pin-to-pin” as shown in the diagram below:Cross-axis Field DirectionDynamic Power ConsumptionIsoLoop Isolators achieve their low power consumption from the way they transmit data across the isolation barrier. By detecting the edge transitions of the input logic signal and converting these to narrow current pulses, a magnetic field is created around the GMR Wheatstone bridge. Depending on the direction of the magnetic field, the bridge causes the output comparator to switch following the input logic signal. Since the current pulses are narrow, about 2.5 ns, the power consumption is independent of mark-to-space ratio and solely dependent on frequency. This has obvious advantages over optocouplers, which have power consumption heavily dependent on mark-to-space ratio.Power Supply DecouplingBoth power supplies to these devices should be decoupled with low-ESR 47 nF ceramic capacitors. Ground planes for both GND 1 and GND 2 are highly recommended for data rates above 10 Mbps. Capacitors must be located as close as possible to the V DD pins.Signal Status on Start-up and Shut DownTo minimize power dissipation, input signals are differentiated and then latched on the output side of the isolation barrier to reconstruct the signal. This could result in an ambiguous output statedepending on power up, shutdown and power loss sequencing. Therefore, the designer should consider including an initialization signal in the start-up circuit. Initialization consists of toggling the input either high then low, or low then high.Data Transmission RatesThe reliability of a transmission system is directly related to the accuracy and quality of the transmitted digital information. For a digital system, those parameters which determine the limits of the data transmission are pulse width distortion and propagation delay skew.Propagation delay is the time taken for the signal to travel through the device. This is usually different when sending a low-to-high than when sending a high-to-low signal. This difference, or error, is called pulse width distortion (PWD) and is usually in nanoseconds. It may also be expressed as a percentage:PWD% = Maximum Pulse Width Distortion (ns) x 100% Signal Pulse Width (ns)For example, with data rates of 12.5 Mbps:PWD% = 3 ns x 100% = 3.75%This figure is almost three times better than any availableoptocoupler with the same temperature range, and two times better than any optocoupler regardless of published temperature range. IsoLoop isolators exceed the 10% maximum PWD recommended by PROFIBUS, and will run to nearly 35 Mb within the 10% limit.Propagation delay skew is the signal propagation differencebetween two or more channels. This becomes significant in clocked systems because it is undesirable for the clock pulse to arrive before the data has settled. Short propagation delay skew is therefore especially critical in high data rate parallel systems for establishing and maintaining accuracy and repeatability. Worst-case channel-to-channel skew in an IL700 Isolator is only 3 ns, which is ten times better than any optocoupler. IL700 Isolators have a maximum propagation delay skew of 6 ns, which is five times better than any optocoupler.Application DiagramsIsolated PROFIBUS / RS-485NVE offers a unique line of PROFIBUS / RS-485 transceivers, but IL700 high-speed digital signal isolators can also be used as part of multi-chip designs with non-isolated PROFIBUS transceivers.Package Drawings, Dimensions and Specifications8-pin MSOPPin spacing is a BASICdimension; tolerances do not accumulateNOTE:8-pin SOIC PackageDimensions in inches (mm)0.060 (1.5)Pin spacing is a BASICdimension; tolerances do not accumulateNOTE:8-pin PDIPOrdering Information and Valid Part Numberslank = Tube= 7'' Tape and Reel= 13'' Tape and Reel= 80/20 Tin/Lead PlatingE = RoHS Compliant-1 = MSOP-2 = PDIP-3 = 0.15'' 8-pin SOIClank = StandardT = High TemperatureS = High Speed711 = 2 Drive Channels712 = 1 Drive Channel1 Receive ChannelIL = Isolators Valid Part NumbersIL711-1IL711-1EIL711S-1IL711S-1EIL711T-1IL711T-1EIL711-2IL711-2EIL711T-2IL711T-2EIL711-3IL711S-3IL711T-3IL711-3EIL711S-3EIL711T-3EAll MSOP and SOIC partsare available on tape and reel.IL712-1IL712-1EIL712S-1IL712S-1EIL712T-1IL712T-1EIL712-2IL712-2EIL712T-2IL712T-2EIL712-3IL712S-3IL712T-3IL712-3EIL712S-3EIL712T-3ERoHSCOMPLIANTISB-DS-001-IL711/12-Q March 2008 Changes• Added magnetic field immunity and electromagnetic compatibility specifications.ISB-DS-001-IL711/12-P Changes• Correct SOIC package drawing.ISB-DS-001-IL711/12-O Changes• Note on all package drawings that pin-spacing tolerances are non-accumulating;change MSOP pin-spacing dimensions and tolerance accordingly.ISB-DS-001-IL711/12-N Changes• Changed lower limit of length on PDIP package drawing.• Tightened pin-spacing tolerance on MSOP package drawing.ISB-DS-001-IL711/12-M Changes• Changed ordering information to reflect that devices are now fully RoHScompliant with no exemptions.ISB-DS-001-IL711/12-L Changes• Eliminated soldering profile chartISB-DS-001-IL711/12-K Changes• Added RS-485 application circuitISB-DS-001-IL711/12-J Changes• MSOP packages, S- and T-Grades added• Order information updatedISB-DS-001-IL711/12-I ChangesAdded MSOP SpecificationsUpdated IEC and UL Approval NumbersIL711/IL71211About NVEAn ISO 9001 Certified CompanyNVE Corporation manufactures innovative products based on unique spintronic Giant Magnetoresistive (GMR) technology. Products include Magnetic Field Sensors, Magnetic Field Gradient Sensors (Gradiometers), Digital Magnetic Field Sensors, Digital Signal Isolators, and Isolated Bus Transceivers.NVE pioneered spintronics and in 1994 introduced the world’s first products using GMR material, a line of ultra-precise magnetic sensors for position, magnetic media, gear speed and current sensing.NVE Corporation11409 Valley View RoadEden Prairie, MN 55344-3617 USATelephone: (952) 829-9217Fax: (952) 829-9189 Internet: e-mail: isoinfo@The information provided by NVE Corporation is believed to be accurate. However, no responsibility is assumed by NVECorporation for its use, nor for any infringement of patents, nor rights or licenses granted to third parties, which may result from its use. No license is granted by implication, or otherwise, under any patent or patent rights of NVE Corporation. NVECorporation does not authorize, nor warrant, any NVE Corporation product for use in life support devices or systems or other critical applications, without the express written approval of the President of NVE Corporation.Specifications shown are subject to change without notice.ISB-DS-001-IL711/12-QMarch 2008元器件交易网。
LOC111中文资料
LOC111中⽂资料LOC111Linear OptocouplersApplicationsFeaturesDescriptionApprovalsOrdering Information Pin ConfigurationLOC111 is a linear optocoupler for use in telecom, med-ical and power supply isolation circuits. They are available in 8 pin DIP , surface mount or flatpack packages.Modem Transformer Replacement With No Insertion LossDigital Telephone IsolationPower Supply Feedback Voltage/Current Medical Sensor Isolation Audio Signal InterfacingIsolation of Process Control TransducersUL Recognized: File Number E76270CSA Certified: File Number LR 43639-10BSI Certified:BS EN 60950:1992 (BS7002:1992)Certificate #:7344 BS EN 41003:1993Certificate #:73448 Pin Flatpack or DIP PAckage (PCMCIA Compatible)?Couples Analog and Digital Signals ?Wide Bandwidth (>200kHz)?High Gain StabilityLow Input/Output Capacitance Low Power Consumption 0.01% Servo Linearity THD 87dB TypicalMachine Insertable, Wave SolderableSurface Mount and Tape Reel Versions Available VDE CompatibleLOC111 PinoutDLED +LED +V cc 1I1NC NC +V cc 2I 2LOC111Absolute Maximum Ratings are stress ratings. Functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this data sheet is not implied. Exposure of the device to the absolute maximum ratings for an extended period may degrade the device and effect its reliability.Absolute Maximum Ratings (@ 25o C)Electrical Characteristics2Derate Linearly 6.67 mW/°CK3 Sorted Bins Bin A= 0.550-0.605Bin B = 0.606-0.667Bin C = 0.668-0.732Bin D = 0.733-0.805Bin E = 0.806-0.886Bin F = 0.887-0.974Bin G = 0.975-1.072Bin H = 1.073-1.179Bin I = 1.180-1.297Bin J= 1.298-1.426The LOC110/LOC111/LOC112 are shipped in anti-static tubes of 50pieces. Each tube will contain one K3 sorted bin.Bin designation marked on each device (A-J).Orders for the LOC110 product will be shipped using bins available at the date of the order. Any bin (A-J) can be shipped.For customers requiring selected bins D E F G we offer part num-bers LOC111 or LOC112.LOC111Performance Data*The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application department.LOC111Dimensionsmm (inches)Mechanical DimensionsCPC7581 Mechanical DimensionsDimensionsmm(inches)CLARE LOCATIONSClare Headquarters78 Cherry Hill DriveBeverly, MA01915Tel: 1-978-524-6700Fax: 1-978-524-4900Toll Free: 1-800-27-CLARE Clare Micronix Division 145 ColumbiaAliso Viejo, CA92656-1490 Tel: 1-949-831-4622Fax: 1-949-831-4628SALES OFFICES AMERICASAmericas HeadquartersClare78 Cherry Hill DriveBeverly, MA01915Tel: 1-978-524-6700Fax: 1-978-524-4900Toll Free: 1-800-27-CLARE Eastern RegionClareP.O. Box 856Mahwah, NJ 07430Tel: 1-201-236-0101Fax: 1-201-236-8685Toll Free: 1-800-27-CLARE Central RegionClare Canada Ltd.3425 Harvester Road, Suite 202 Burlington, Ontario L7N 3N1 Tel: 1-905-333-9066 Fax: 1-905-333-1824Western RegionClare1852 West 11th Street, #348 Tracy, CA95376Tel: 1-209-832-4367Fax: 1-209-832-4732Toll Free: 1-800-27-CLARE CanadaClare Canada Ltd.3425 Harvester Road, Suite 202 Burlington, Ontario L7N 3N1 Tel: 1-905-333-9066 Fax: 1-905-333-1824EUROPEEuropean HeadquartersCP Clare nvBampslaan 17B-3500 Hasselt (Belgium)Tel: 32-11-300868Fax: 32-11-300890FranceClare France SalesLead Rep99 route de Versailles 91160 ChamplanFranceTel: 33 1 69 79 93 50Fax: 33 1 69 79 93 59 GermanyClare Germany Sales ActiveComp Electronic GmbH Mitterstrasse 1285077 ManchingGermanyTel: 49 8459 3214 10Fax: 49 8459 3214 29ItalyC.L.A.R.E.s.a.s.Via C. Colombo 10/AI-20066 Melzo (Milano) Tel: 39-02-95737160Fax: 39-02-95738829 SwedenClare SalesComptronic ABBox 167S-16329 Sp?ngaTel: 46-862-10370Fax: 46-862-10371United KingdomClare UK SalesMarco Polo HouseCook WayBindon RoadTauntonUK-Somerset TA2 6BG Tel: 44-1-823 352541Fax: 44-1-823 352797ASIA PACIFICAsian HeadquartersClareRoom N1016, Chia-Hsin, Bldg II,10F, No. 96, Sec. 2Chung Shan North RoadTaipei, Taiwan R.O.C.Tel: 886-2-2523-6368Fax: 886-2-2523-6369/doc/0fd841f2770bf78a64295400.html Worldwide Sales OfficesSpecification: DS-LOC111-R6Copyright 2001, Clare, Inc.All rights reserved. Printed in USA.02/23/01Clare cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in this Clare product. No circuit patent licenses nor indemnity are expressed or implied. Clare reserves the right to change the specification and circuitry, with-out notice at any time. The products described in this document are not intended for use in medical implantation or other direct life support applications where malfunction may result in direct phys-ical harm, injury or death to a person.。
元素周期表详表
铥 镱 镥 铪 钽 钨 铼 锇 铱 铂 金 汞 铊 铅 铋 钋 砹 氡 钫 镭 锕 钍 镤 中文 铀 镎 钚 镅 锔 锫 锎 锿 镄 钔 锘
丢 意 鲁 哈 坦 乌 来 鹅 衣 伯 今 拱 他 千 必 泼 艾 冬 方 雷 阿 土 仆 读音 由 拿 不 眉 局 陪 开 哀 费 门 诺
169 173 175 178.5 181 184 186 190 192 195 197 200.6 204.5 207 209 209 210 222 223 226 227 232 231 原子量 238 237 244 243 247 247 251 252 257 258 259
砷 硒 溴 氪 铷 锶 钇 锆 铌 钼 锝 钌 铑 钯 银 镉 铟 锡 锑 碲 碘 氙 铯 钡 镧 铈 镨 钕 钷 钐 铕 钆 铽 镝 钬 铒
申 西 秀 克 如 思 乙 告 尼 目 得 liǎo 老 巴 吟 隔 因 西 梯 帝 典 仙 色 贝 兰 市 普 女 颇 衫 有 轧 忒 滴 火 耳
75 79 79 83.8 85.5 87.5 89 91 93 96 98 101 103 106.5 108 112.5 115 118.5 122 127.5 127 131.3 133 137.3 139 140 141 144 145 150.5 152 157 159 162.5 165 167
4s2 4p3 4s2 4p4 4s2 4p5 4s2 4p6 5s1 5s2 4d1 5s2 4d2 5s2 4d4 5s1 4d5 5s1 4d5 5s2 4d7 5s1 4d8 5s1 4d10 4d10 5s1 4d10 5s2 5s2 5p1 5s2 5p2 5s2 5p3 5s2 5p4 5s2 5p5 5s2 5p6 6s1 6s2 5d1 6s2 4f1 5d1 6s2 4f3 6s2 4f4 6s2 4f5 6s2 4f6 6s2 4f7 6s2 4f7 5d1 6s2 4f9 6s2 4f10 6s2 4f11 6s2 4f12 6s2
自动控制原理及其应用(第二版黄坚)课后习题答案
n
P2=G3G2 Δ2 =1
C(s) R(s)
=
Σk=1PkΔk
Δ
=1+GG22HG11++GG12GG23H2
第二章习题课 (2-11b)
2-11(b) 求系统的 传递函RC数(s()s)
R(s)
解:
G3(s) G3(s)
R=(sG_) 1G11+2+G+_GG4GH1 12GGGG112(3Hs+) G++G1G1G2GG42+(GH3sG)4(CsG4)(2Hs()s)
(s+1s)+22(s+3)est
+
s=0
s(ss++21)2est s=-3
+
lsim-1
d[
s(ss++23)est ds
]
=
2 3
+
1 12
e-3t+slim-1[
(-s(2s-24+s3-6)2)est+
(s+2)test s2+3s ]
(2-4-1) 求下列微分方程。
A2=(s+2)Y(s) s=-2 A3=(s+3)Y(s) s=-3
力所示,试采用复数阻抗法写出它们的传
递函数。
C
R2
R3
ui R1
－
∞ ＋
uo
＋
R4
R5
UR1I==－－UU(ROIR=4=2－＋+－RRR4(RR5+R1R)3＋SR5R(2RR4CRRR5+325(2RU13R5R+SR1O33RC(5SSUR3+CC)O3R(+S+(RRR2CR1+－232)+2+RSR+1RRC3R3))32＋R+S(3RR1C54R)4R+++315RRSR)C535U)＋O1
RC411操作员手册说明书
RC411 Operator ManualFOREWORD1.Read the instructions contained in the enclosed booklet carefully, because it contains important information on installation, operation and maintenance safety. Store this booklet carefully for any further consultation by other operators.2.Having removed the packing material, check that all the equipment is present.If there is any doubt, do not use it and contact qualified personnel.The packing elements (plastic bags, foam polystyrene, nails, etc.) should be kept away from children, because they are dangerous.3.Before switching the equipment on, make sure that the model plate data conforms to that of the electrical and water distribution network.4.Installation should be carried out by qualified personnel according to the manufacturer's instructions.5.This equipment should be destined to the use which it has been conceived for. Any other application should be considered improper and consequently dangerous.6.The equipment should only be used by personnel trained for its use.7.Operators must strictly follow all hygienic requirements in the handling of clean dishware and cutlery.8.Do not leave the machine in an environment at temperatures lower than 0°C.9.The protection of the machine is IP X4, therefore it should not be washed with high pressure directed water jets.10.Qualified personnel only can access the control panel, after having disconnected the machine from the primary current supply.11.The appliance is made according to EEC 89/336 regarding radio noise suppression and electromagnetic compatibility.12.According to EEC directive nr.23 of 19/02/1973 and the law of actuation nr.791 of 18/10/1987, our appliances are built-up according to the good technique norms in force in Italy and abroad.13.Noise level of the machine, less than 63dB(A)INSTRUCTIONS FOR USECONTROL PANELH3Q1H2H2Pilot lamp "machine READY"H3Pilot lamp "machine WORKING"Q1 Main switchOFFGREEN MachineRED Machine ON / Wash cycleselectorS9CycleOPERATION AND USE1. Before washing make sure that:•the wall-mounted on/off switch is switched on;•the water tap is open;•water is present in the distribution network;•the pump protection filters are installed in their respective positions;•the overflow in inserted;•all rotating parts are free;•the rinse aid dispenser is full;•make sure that dishware is in good conditions as it may cause cleaning difficulty and haven bacteria.2. Press the "Q1" button (RED) to enable the automatic wash tank filling and the consequent triggering of the heating element.3. As soon as visual indicator "H2" is ON; pour about 30 gr. of detergent directly into the tank, paying attention to distribute it uniformly on the filters, the quantity being according to supplier's instructions. Add 15 gr. every 7 cycles to achieve a concentration of 1,5gr/lt. In order to respect our environment, use only the correct amount of detergent.When using chlorinated detergent, it is suggested to use an automatic dispenser; otherwise, brownish spots might appear on the surfaces due to chlorine reactions. Detergent should always be placed near the pump filter.4. Then, introduce the glasses or the cups to wash, after having removed the solid waste and having placed them into the proper racks. The cups and the glasses should be turned upside down, while the cutlery should be put vertically into the proper container, and the same applies to dishware.5. Press the "S9" button to select the wash cycle according to conditions of•(pos.short cycle with normally dirty dishes;•(pos.long cycle with particularly dirty dishes or deep dishes 6. Close the door for the wash cycle start.The end of which will be indicated by the switching off of the "H3" lamp.standards, guaranteeing a final rinse at 85°C. Wash cycle automatically lengthened if final rinse temperature is not reached. When this auto-cycle intervenes and the cycle is pro-longed, after 8 minutes the "H3" indicator flashes to indicate this intervention and the cycle continues (water supply temperature is likely to be the problem, otherwise contact an assistance centre since it is a rinse water heating intervention.). Turn off the machine to remove this alarm.7. Remove the rack and slightly incline it to permit a perfect drain; allow dishware to dry and after having washed one’s hands, handle the rack in order not to touch the dishware inside then place the rack on hygienically clean shelves.8. At the end of washing, with the machine off (Q1 – GREEN pos.), empty out the tank by taking out the overflow tube, then close the door and with the machine on (Q1 – RED pos.).for a few minutes to wash the machine. Then again with the machine off and wait until the tank is completely emptyAt this point, the tank filter can be taken out, in order to be washed, then replace it with the overflow in its place.For any further information concerning equipment cleaning, read chapter "USEFUL SUGGESTIONS".turning off the main supply through the general wall switch and close the water supply.INSTRUCTIONS DURING THE WASHING1) Do not plunge bare hands into the water containing the detergent. If this happens, wash them immediately and abundantly with fresh water.2) When the machine is operating, do not open the door too rapidly.3) Use only specific anti-foaming detergents.4) Disconnect the equipment in case the machine is out of order or it does not work properly. For the repairs consult a technical assistance centre authorised by the manufacturer and ask only for an original spare parts.5) Never modify the thermostat settings.6) Check that lamp "H2" is on.7) Wash tank water should be changed at least twice a day or according to daily wash requirements.8) Do not subject clean dishware to any further cleansing treatment such as brushes or drying towels.If these instructions are not followed, the safety of the equipment can be compromised.USEFUL SUGGESTIONS1) MAINTENANCEIMPORTANT: Before carrying out the cleaning and maintenance operations, disconnect the equipment from the electric supply.Frequently check and clean the nozzles. The frequency of this operation will depend on the quantity of residues, which may result in an unsatisfactory washing result.♦For the inside and outside cleaning of the machine, do not use corrosive products such as sodium hypochlorite (bleach) savelling water and hydrochloric acid, acids, steel wool or steel brushes.♦The presence of calcium and magnesium salt in the water can compromise machine performance, thus ask qualified personnel to remove the deposits periodically.♦In order to avoid some oxidation risks, or chemical reactions, generally the stainless steel surfaces have to be well cleaned.2) OPTIMAL RESULTS:A possible wash deficiency can be noticed when residue remains.Marks can be caused by an insufficient rinse: in this case checkthat the rinse nozzles are clean and that there is sufficient water supply pressure.In case of dishware residue check that:•the washing nozzles are clean•the water temperature is around 60°C•there is detergent•the pump suction filter is clean•the racks are suitable for the dishes and cutlery that are to be washed•the position of the cutlery and the dishes in the racks are correct3) TEMPORARY MACHINE NON-USEIn case the machine is stopped for some weeks, it is recommended before closing it to fill the tank and run the machine with clean water, then empty it out, in order to avoid the forming of bad odour and that any residue remains in the pump.If necessary repeat this operation until the water leaving the machine is clean. If the machine is stopped for many weeks, it is recommended to oil the stainless steel surfaces with paraffin oil and to discharge the water from the boiler and the electric pump.4) SANITIZING THE MACHINESanitizing the machine at least once a week is of the utmost importance in order to guarantee hygiene even when the machine is not in use.It is advisable to use a disinfecting product suggested by an authorised detergent dealer.The use of this product will satisfy hygienic requirements, even during machine non use.Before switching off the machine run the machine briefly with cleanwater.5) HARD WATER CONDITIONSIf a hard water supply is present, mineral deposits will form within the machine and also on dishware.In order to avoid the above conditions a periodic removal of these deposits is necessary.The frequency and method of this operation upon consultation by your detergent supplier.INSTALLATION AND MAINTENANCEINSTRUCTIONSThe following instructions are addressed to qualified personnel the only one authorised to carry out checks and repairs, if any.The manufacturer declines any responsibility in the case of interventions made by a non-qualified personnel or the use of spare parts other than those supplied by the Manufacture.INSTALLATIONDuring installation, carry out proper machine levelling, which is a prerequisite for a correct operation thereof (max. tolerance 2°).In order to prevent any damage caused by steam going out of the machine, make sure that the surrounding materials do not deteriorate in its presence. After machine installation check thermostat settings, booster 85°C, tank 60°C.1) ELECTRICAL CONNECTIONThe electrical safety of this equipment is only assured if it is connected as follows. It is necessary to connect the equipment to an effective earthing as specified by the electrical safety regulations in force. Check that this basic requirement is complied with, in case of any doubt ask for a careful check of the installation by a qualified personnel. In the case the earthing is not efficient there will be a dispersion due to the suppresser.The machine shall be included in a correctly dimensioned equipotential, whose effectiveness is to be very tight in accordance to the procedures set for in the applicable safety standards. The connection shall be performed through a screw marked by the plate near the rear side of the appliance.The manufacturer declines any responsibility for any damages caused by lack of an effective ground installation. For the electrical power supply have available a wall circuit breaker switch with multiple phase protection according the following table with contact aperture distance, equal to or not exceeding 3mm and a supply cable no less than 2.5mm².kW 230/240V∼ 230/240V3N∼3∼ 400/415V7,75kW 40A 25A 16A5,45W 32A 16A 16A3,10kW 16AFor other supplies the cable cross section and the circuit breaker switch must be calculated according to voltage and length of cabling. If cabling too long adjust cable size to Amp rating; do not pull on supply cable or install it under tension. If cable needs to be replaced use type H07RN-F.2) WATER CONNECTIONInstall a 55°C water tap in a well accessible place, terminating in a 3/4" fitting, which the pipe strainer and inlet hose shall be connected to. Carefully comply with any national or regional regulations in force.The operating pressure should be neither less than 2 bars or greater that 4 bars (200/400 kPa). If water pressure is inferior then 2 bar, a pressure increase pump is necessary. If water pressure exceeds 4 bar, a pressure reducer is necessary.In order to obtain best results, it is suggested that the water supply have a hardness not greater that 8 Clarke.3) WATER DRAINArrange a water drain towards the floor with siphon and connect the machine with the flexible tube given with the machine, so that it leans towards the drain. Moreover, make sure that the hose does not have constrictions.Make sure that the building drain tubing withstands temperatures up to 70°C.4) RINSE AID DOSAGEMake sure that rinse aid suction hose is correctly installed in its proper container. The dosage is automatic with the adjusting of the screw "I", which after screwing to a full stop unscrew two turns. At this point the machine automatically takes the necessary liquid for every rinse: during the washing operations, check that the liquid of the container does not run short.For filling the dosing tube, start the machine without plugging the overflow in: at that point switch the machine on and off. Repeat this operation several times at intervals of few seconds, until the rinse aid reaches the injector. Wait until the machine reaches the correct temperature (lamp "H2" on). Make some empty cycles, then try to wash: if the objects washed show some drops, this means that the rinse aid is insufficient. On the contrary, the presence of marks can mean that there is too much rinse aid or the water is too hard. The regulation can change according to the kind of rinse aid.5) DETERGENT DOSAGE (for machines with built-in detergent dispenser)With the screw on the side of the detergent pump, close completely the product intake, and then slowly open the screw until the desired intake quantity has been reached. The correct quantity is indicated by the detergent supplier. Check that the intake of the pipe during the rinse cycle is as preset. (1cm = 1g approximately). Maximum intake or delivery distance: 2 meters.6) LOADING AND UNLOADING OF THE MACHINEFor the transportation of the machine from the delivery point to the final installation position, use a fork lift or adequate lifting equipment used by authorised staff. Lift the machine by its frame, taking care that any protruding parts are not damaged (discharges, wiring etc.).7) MACHINE DISMANTLINGAt the end of its normal lifetime, the machine has to be taken apart according to the local regulations in force by separating the components as follows: • metal parts: hood, platforms, frames, filters• electrical parts: motors, remote control switches, microswitches, wiring • plastic parts: racks, connections • rubber parts: tubes, sleevesENERGY CONSUMPTIONModel Wash tank capacity (l) Rinse waterconsumpt. (l)Tankheater (W)Rinse heater (W)Wash pump (W)Total electric load (W)Output in racks per hour with 55°C inlet waterOutput in racks per hour with 12°C inlet waterRC41121 3,5 2000MAX7000750MAX 775030/20 20In the event of low water supply temperature, the will be a subsequent machine output drop.WIRING DIAGRAMC1 Anti noise filterC3 CondensatorheaterE2 BoosterE3 TankheaterH2 Pilot lamp machine readyH3 Pilot lamp machine workingKE2 Booster heater contactorKE2b Safety contactor of booster heaterM2 Rinse pump (if required)M3 Wash pumpM5 Drain pump (if required)MD Detergent dispenser (if required)switchQ1 MainswitchS1 DoorS2 PressureswitchS9 Cycle selection push buttonthermostatSE2 BoosterSE2a Booster thermostatSE2b Booster safety thermostatthermostatSE3 TankSE3b Tank safety thermostatY1 Rinse solenoid valveX1 JunctionThe manufacturer declines any responsibility for any printing errors contained in this booklet. The manufacturer also reserves the right to make any modifications to its products that do not affect the basic characteristics thereof.。
National Instruments PXIe系列产品数据手册说明书
Board Assembly Part Number(s)Part Number Description159040B-01L or later NI PXIe-7846R159040B-02L or later NI PXIe-7847R159040B-03L or later NI PXIe-7856R159040B-04L or later NI PXIe-7857R159040B-05L or later NI PXIe-7858RManufacturer: National InstrumentsVolatile MemoryUser Accessible/ BatteryType Size System Accessible1Backup? Purpose Method of Clearing2(7846R/7847R/7856R/7857R)FPGA Block RAM 11,700 KB Yes/Yes No Data storage during Cycle PowerVI Execution(7858R)FPGA Block RAM 16,020 KB Yes/Yes No Data storage during Cycle PowerVI Execution (7847R/7857R/7858R)DRAM 512MB Yes/Yes No Onboard Memory Storage Cycle PowerNon-Volatile MemoryUser Accessible/ BatteryType Size System Accessible Backup? Purpose Method of Clearing(7846R/7847R/7856R/7857R)Flash 64 Mb No- Device information No/Yes Product Identification None available to user- Calibration data3No/Yes Calibration Information None available to user- Calibration metadata Yes/Yes User-defined See Clearing Notes- FPGA bitstream Yes/Yes User LV FPGA VI Bitstream See Clearing Notes(7858R)Flash 128 Mb- Device information No/Yes No Product Identification None available to user- Calibration data3No/Yes Calibration Information None available to user- Calibration metadata Yes/Yes User-defined See Clearing Notes- FPGA bitstream Yes/Yes User LV FPGA VI Bitstream See Clearing Notes1 Items are designated No for the following reason(s):a) Hardware changes or a unique software tool from National Instruments are required to modify contents of the memorylisted.b) Hardware-modifying software tools are not distributed to customers for any personal access or customization, also knownas non-normal use.2 The designation None Available to User indicates that the ability to clear this memory is not available to the user undernormal operation. The utilities required to clear the memory are not distributed by National Instruments to customers fornormal use.3 Calibration constants that are stored in device calibration memory include information for the device’s full operating range. Calibration constants do not maintain any unique data for specific configurations at which the device is used unlessotherwise specified.Media StorageUser Accessible/ BatteryType Size System Accessible Backup? Purpose Method of Clearing NONEClearing Notes:Calibration metadata: There are two items in the calibration metadata that need to be cleared:1.To clear the user-defined information, you can use the Calibration Utility to write a known value to the user stringfield.2.To clear the calibration password, you can use the Calibration Utility to change the password to a known value.FPGA bitstream: You can use the NI-RIO Device Setup utility to erase the FPGA bitstream data. For more details, visit /info and enter the infocode fpgaflashclr.Terms and DefinitionsUser Accessible Allows the user to directly write or modify the contents of the memory during normal instrument operation. System Accessible Does not allow the user to access or modify the memory during normal instrument operation. However, system accessible memory may be accessed or modified by background processes. This can be something that is not deliberate by the user and can be a background driver implementation, such as storing application information in RAM to increase speed of use.Cycle Power The process of completely removing power from the device and its components. This process includes a complete shutdown of the PC and/or chassis containing the device; a reboot is not sufficient for the completion of this process. Volatile Memory Requires power to maintain the stored information. When power is removed from this memory, its contents are lost.Non-Volatile Retains its contents when power is removed. This type of memory typically contains calibration or chip configuration information, such as power up states.。
S1-245B_S1-262A 管螺纹车床电路图200912
8.10 / 1
-SB9
21 22 47
47
47
13
-SB10
14
49
-XT1 39
47
-XT3 43
47
13
-KM4
/9.5 14
-XT1 40
49
-XT3 42
49
49
49
49 / 10.4
8.10 / 6
A1
-KM4
A2
6
1
2 /4.5
S1-245B/S1-262A管螺纹车床电路图200912
页描述：主电机/卡盘电机 图号：
= +
10
L11 / 4.1 L21 / 4.1 L31 / 4.1
4 第 3 页 共 21 页
1
3.10 / L11 3.10 / L21 3.10 / L31
2
3
快速电机
1.5mm² L11 L21 L31
电磁阀电源
照明/指示灯
控制电源
1.5mm² L11
L31
1
3
-QF6
10A
2
4
-TC
JBK5-400 PE
-PE
PE 28V/50VA
03
04
1
3
-VC
˜
10A
-
+
˜
2
4
-24V
+24V
-XT3 52
53
-24V
+24V
-XT1 52
53
-24V
+24V
-24V
11.7
+24V
11.7
网络和信息安全第3章 对称密码体系
2019/11/23
5
3.1 流密码一般模型
流密码原理框图
k
安全信道
k
密钥流 生成器
zi
mi E(zi,mi) ci
信道
密钥流 生成器
zi
ci D(zi,ci) mi
2019/11/23
6
3.1 流密码一般模型
流密码体制的安全性 当流钥序列是具有均匀分布的离散无记忆随机序列 时, 在理论上是不可破译的.
zi f ( i, k ), ci E (zi,m i). F :状 态 转 移 函 数 f :密 钥 流 生 成 函 数
2019/11/23
k
密钥流生成器
zi
mi E(zi,mi)
ci
10
3.1 流密码一般模型
自同步流密码(SSSC)
密钥流生成器是一种有记忆变换器 密钥流与明文符号有关：
2019/11/23
3
流密码的基本概念
流密码是将明文划分成字符(如单个字母)，或其编码的 基本单元(如0, 1数字)，字符分别与密钥流作用进行加 密，解密时以同步产生的同样的密钥流实现。
流密码强度完全依赖于密钥序列的随机性(Randomness) 和不可预测性(Unpredictability)。
(1) J=J+SI+KI （mod 256）； (2) 交换SI和SJ 。
2019/11/23
RC4可以支持不同密钥长度，美国政府特别限定，用 于出口的RC4的密钥长度不得超过40位。
2019/11/23
14
3.1.2 快速软、硬件实现的流密码算法
RC4使用了一个28字节大小的非线性数据表(简称S表), S表的值S0,S1,…,S255是数字0到255的一个排列。对S表 进行非线性变换,得到密钥流。
S1D13305中文资料
元器件交易网
The information of the product number change
Starting April 1, 2001, the product number will be changed as listed below. To order from April 1, 2001 please use the new product number. For further information, please contact Epson sales representative.
SDU1374#0C SDU1375#0C SDU1376#0C SDU1376BVR SDU1378#0C
• S1D1380x Series New No. Previous No.
SDU1386#0C
New No.
S5U13806P00C
S5U13503P00C S5U13504P00C S5U13505P00C S5U13506P00C
S1D13305 Series S1D13305D00A S1D13305F00A S1D13305F00B
S1D1370x Series S1D13704F00A S1D13705F00A S1D13706B00A S1D13706F00A S1D13708 Series
• S1D1350x Series Previous No.
S5U13704P00C S5U13705P00C S5U13706P00C S5U13706B32R S5U13708P00C
• S1D13A0x Series Previous No.
SDU13A3#0C SDU13A4#0C
New No.
NEC DTH11SLP-BLK_Manual.pdf USER GUIDE
LOCATION OF CONTROLSBottom ViewTop ViewNothing contained in this manual shall be deemed to be, and this manual does not constitute, a warranty of, or representation with respect to, any of the equipment covered. This manual is subject to change without notice and NEC Infrontia Corporation has no obligation to provide any updates or corrections to this manual. Further, NEC Infrontia Corporation also reserves the right, without prior notice, to make changes in equipment design or components as it deems appropriate. No representation is made that this manual is complete or accurate in all respects and NEC Infrontia Corporation shall not be liable for any errors or omission. In no event shall NEC Infrontia Corporation be liable for any incidental or consequential damages in connection with the use of this manual. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied or reproduced without prior written consent of NEC Infrontia Corporation.2004 by NEC Infrontia Corporation All Rights Reserved.IMPORTANT SAFETY INSTRUCTIONSWhen using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons by doing the following:1. Read and understand all instructions.2. Follow all warnings and instructions marked on the product.3. Do not use this product near water. For example, near a bathtub, kitchensink or laundry tub, in a wet basement, or near a swimming pool.4. Do not place this product on an unstable cart, stand, or table. The productmay fall, causing serious damage to the product.5. Slots and openings in the cabinet and the back or bottom are provided forventilation. T o protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation unless proper ventilation is provided.6. Never push objects of any kind into this product through cabinet slots asthey may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product.7.To reduce the risk of electric shock, do not disassemble this product.Take it to a qualified serviceman when service or repair work is required.Opening or removing covers may expose you to dangerous voltages or other risks. Incorrect reassembly can cause electric shock when the product is subsequently used.8.Avoid using a telephone during an electrical storm. There may be aremote risk of electric shock from lightning.9. Do not use the telephone to report a gas leak in the vicinity of the leak. Please keep this unit away from equipment that uses radio waves or microwaves such as a portable radio or a microwave oven. This type of equipment may cause improper operation.CONNECTION TO THE TELEPHONE LINEConnect the line cord to the bottom of the DTH-1-1 (BK) TEL and to PBX/KTS Phone Jack.Note : Use the DTH-1-1(BK)TEL only behind a PBX or a KTS. SPECIFICATIONSDP dialMake ratio:39 1%Pulse speed :10 1ppsDTMF dialLevel (High group):0 -5.5dBm(Low group):0 -7.5dBmSignal duration:80 10msMinimum pause:80 10msFlashFlash time:630 20msDIAL MODEEither "T (T one/DTMF)" or "P (Pulse/DP)" mode is selected by the Dial Mode switch which is located on the bottom of the DTH-1-1 (BK) TEL.Note : Confirm T elephone Network method or PBX/KTS method.T PTEMPORARY SWITCH OVER OF THE DIALING MODEAfter a connection has been set up to use PULSE dialing, switch over to TONE dialing can be made by pressing the * button. Certain services offered by some Public T elephone Exchanges or PBXs, e.g. control of a telephone answering system, simple data traffic, etc, can then be utilized by dialing additional digits.The telephone is automatically reset to PULSE dialing when the handset is cradled.FLASHMAKING A CALL1. Lift Handset. The IN USE LED will illuminate.2. Wait for the Dial Tone and then dial the telephone number .3. Hang up to terminate the call.Note : A Trunk Access Code may be necessary before dialing an external telephone number if the DTH-1-1 (BK) TEL is connected to a PBX/KTS.1. While on a call, press FLASH Key ..VOLUME CONTROLThe handset earpiece volume can be adjusted in 6 stepped increments during a call.Press p to increase the volume (3 steps up), or q to decrease the volume (2 steps down).Note : If the DTH-1-1 (BK) TEL is connected to a PBX/KTS, you can send the command by pressing the FLASH Key. If the DTH-1-1 (BK) TEL is connected to the Telephone Network, you can "Disconnect and Recall" by pressing the FLASH Key.TELEPHONE RINGER SET UPThere are three different ringers available and three different volumes for each ringer. The ringer and volume levels can be set using the following operation.1. Lift Handset.2. Press MUTE Key.3. Dial "#".4. Select a number 0-9 from the table.5. Press MUTE Key.6. Hang up to finish.Note : If you disconnect the phone from the network, the ringing tone assignment will default to the factory setting within a few hours.Dial 1234567890A A A B B B C C C -Ringer Type Low Low Low Mid Mid Mid High High High OffVolume Default:6"Flash"HANDSET MIC MUTE1. While on a call, press MUTE Key to mute.2. Press MUTE Key again to resume conversation.Speed Dial Memory Keys.Note : Flash can be stored in memory dial, but will count as one of the total 21 digits allowed.Note :MESSAGE WAITING INDICATORMany PBX systems have a feature called Message Waiting. DTH-1-1 (BK) TEL will show if a message was received in your absence by flashing the Message Waiting Indicator. This function operates differently depending on the PBX / KTS being used. Please contact the system administrator for more information.MEMORYDTH-1-1 (BK) TEL has 4 One-T ouch Speed Dial Memory Keys. Once a number has been stored in a Memory location, you only have to go off-hook and press one button to make the call.Storing One-Touch 1. Lift Handset and press MUTE (ignore anything you hear in the earpiece).2. Select a location by pressing the corresponding Speed Dial key.3. Enter the telephone number to be stored (up to 21 digits) using the number keys.4. Press MUTE again and replace the handset. The number is now stored.Dialing Using One-Touch Memory Keys.1. Lift the handset and wait for a dial tone.2. Dial the desired number by pressing the corresponding Memory Key.If you disconnect the phone from the network,One-Touch memories will be erased in a few hours.LAST NUMBER REDIAL1. Lift Handset.2. Press REDIAL Key to dial the last # dialed.Note : If you disconnect the phone from the network, redial memory will be erased in a few hours.WALL MOUNTINGThe DTH-1-1 (BK) TEL is suitable for wall mounting. Check for hidden cables, water pipes, etc. before drilling holes. Before you commence, check that the intended mounting point is within reach of a Telephone Socket.1. Use the template to mark the position of the two screws (not supplied) which will secure the DTH-1-1 (BK) TEL in position.2. Drill the holes.3. Fit the screws (not supplied) to the wall, leaving 3.3 mm sticking out (use wall anchors if necessary, not supplied).4. Place the two holes on the base of the telephone over the installed screws, then slide into place.Note: When the DTH-1-1 (BK) TEL is wall mounted, the hanger hook (with serrated top) is located on the base. Rotate 180 degrees (so the lip protrudes) and replace.FCC Part 68 RegistrationThe equipment complies with Part 68 of the FCC Rules. A label which contains the FCC Registration Number and ringer equivalence number(Ren) for the equipment, country of origin, and model number among other information, is located on the bottom of the equipment. If requested this information should be provided to the telephone company.The equipment uses the following USOC jacks: RJ11C.KX-type telephone with message waiting and/or line status indicators may only be connected to host systems and not to the Network.The REN is used to determine the quality of the device which may be connected to the telephone line. Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most, but not in all areas, the sum of RENs should not exceed five (5.0). T o be certain of the number of devices that may be connected to the line, as determined by the total RENs, contact the telephone company to determine the maximum REN for the calling area.If the equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. If advance notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.The telephone company may make changes in its facilities, equipment, operation, or procedures that could effect the operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make the necessary modifications in order to maintain uninterrupted service.If trouble is experienced with this equipment, please contact your NEC Dealer for repair and/or warranty information. If the trouble is causing harm to the telephone network, the telephone company may request you to remove the equipment from the network until the problem is resolved.NO REPAIRS CAN BE DONE BY THE CUSTOMER.The equipment is hearing-aid compatible.CAUTION: The act of monitoring or recording telephone conversations under certain circumstances may violate federal or state statutes. Consultation with your legal counsel prior to engaging in such practices would be advisable.FCC Part 15C omplies with the limits for a Class B computing device pursuant to Subpart J of Part 15 of FCC Rules.INDUSTRY CANADA (CS-03)The Load Number of the equipment: N/A"Notice: The Industry Canada label identifies certified equipment. The certification means that the equipment meets certain telecommunication network protective operational and safety requirements. Industry Canada does not guarantee the equipment will operate to the user's satisfaction." "Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of local telecommunications company. The equipment must also be installed using an acceptable method of connection. In some cases, the company's inside wiring associated with a single line individual service may be extended by means of a certified connector assembly (telephone extension cord). The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.""Repairs to certified equipment should be made by an authorized Maintenance facility designated by the supplier.Any repairs or installations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request that the user disconnect the equipment.Users should ensure, for their own protection, that the electrical ground connections of the power utility, telephone lines, and internal metallic water pipe system, if present, are connected together. This protection may be particularly important in rural areas."Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.SAFETY CONSIDERATIONS:This equipment complies with Underwriters Laboratories Standard U.L. 60950 First Edition.。
常见碳素钢管换算
作为主要钢材，钢管在我们日常生活中应用广泛。
石油、天然气的运输，制造建筑结构网架，制造公路桥梁等领域，可以说钢管不仅减轻了支架重量，节省了建材，还使得施工也变得越来越简易。
想必在钢材买卖和建筑施工中了解钢管的重量是必要的。
那么，钢管理论重量是如何计算的呢？一起来看各种钢管理论重量表大全。
无缝钢管理论重量表:镀锌钢管理论重量表:捉榕外径壁厚IN1最小2E烬管（6米定尺）据薜管（6米定尺）公称内径页寸米重kg根重關米重蚯根重kg DN1S1/Z 21.3 2.8 2.45 1 28 7.68 1.357 8,14 DNZO3丹2& 9 2.6 2.45 1 7b10 56 DN25133.7 3.2 2.0 2. 41 14 46 2 554 IS. 32 DH32 1.25 42. 4 3.5 3. 06 3.36 2D. 16 3.56 22DN4015 4S.3 3.5 3一吧 3 07 23. £2 4,10 24.60 DH50 2 创3 3.9 3,325 5.29 31.74 s.eor 33. &4 DM65 2.5 76. 1 4 0 3 5 7 1142 667 53645 21 DN80380.9 4.08 38 50.28 8 88 53.29DN1004114.3 4,01C 88 65 2311.53 63 18DH12S 5 140 4.515.0490. 2415.942BN1S06168.3 4,516 18109.08 19,27 115.62DW2008 Z13.16-0（輝I）31 53 189. 18镀锌钢管重量计算公式：［（外径-壁厚）*壁厚］*0.02466=kg/米（每米的重量）不锈钢管理论重量表:焊接钢管理论重量表:螺旋钢管理论重量表:矩形方钢管理论重量表:方矩形钢管理论重量计算公式：正方形和长方形（矩形）截面碳钢钢管：每米重量单位：kg/m（千克/米）& lb/ft（磅/英尺）常用方矩管计算公式为：（长+宽）X 2-3.14 -厚度X厚度X 0.02466= kg/m公式二：kg/m = (Oc - 4Wt) * Wt * 0.00785其中：Oc是钢管外周长，Wt是钢管壁厚；正方形Oc=4*a;长方形Oc=2a+2b a,b是边长通俗的解释为：4x壁厚x（边长-壁厚）x7.85其中，方管边长和壁厚都以毫米为单位，直接把数值代入上述公式，得出即为每米方管的重量，以克为单位。
Marantz NA-11S1 Reference Network Audio Player and DAC
鱼
日 ； ＿ 、
Ｉ ・ ● ●
一
Ｈ一
¨
——— ——— —］蝴
囝 圈
ｆ 闰 酋
霞
ＮＡ－ １ Ｉ Ｓ １ 必 须通 过 有线 连接 加
个硬盘干 啥？
０
基 本 的 设 置 对 我 完 全 不 是 问题 ，我 的路 由器开 启了Ｄ ＨＣ Ｐ 功 能 ，而 且 已经 连到 外 网 。用 网线 把ＮＡ一１ １ Ｓ １ 连 到路 由器的
Ｍａ ｃ 的ｉ Ｔ ｕ ｎ ｅ ｓ 作 为讯 源 ，这一 功
能需 要 无 线 Ｗｉ —Ｆ ｉ 网络 环 境 ，
Ｍ ａ ｒ ａ ｎ ｔ ｚ
Ｎ Ａ一１ １ Ｓ １ Ｒ ｅ ｆ ｅ ｒ ｅ ｎ ｃ ｅ Ｎｅ ｔ ｗｏ ｒ ｋ Ａｕ ｄ ｉ ｏ Ｐ ｌ ａ ｙ ｅ ｒ ａ ｎ ｄ ＤＡ Ｃ
文 ● 刘 意思 摄 影 ● 庄 宏道
国内市场上能够见 到的网络音 乐播放器 并不多 ，而 且 除了Ｌ ｉ ｎ ｎ ，几乎没有一个发烧 品牌把这种产 品作 为数字音 源的主 力产 品在做 。而马兰 士Ｎ Ａ 一 １ １ Ｓ １ 是最近 加入这 个高档网络音 乐播放器俱 乐部的新成
是 由 日本 的白河工 厂制造
键 、 ＵＳ Ｂ ｇ ｌ 耳 机插 口所 占据 ， 左右 两侧 区域 是 从 中间 向 外 逐
ｉ ｎ ｋ 光纤和 同轴数字输 入各 网络播放功 能
光 线和 同轴 输 出 各 一 ，剩 如 前 所 述 ， ＮＡ—ｌ ｌ Ｓ
渐收 拢 的 曲面 。 两 道 凹 槽之 中
基 本 上 ，根 据 数 字 音 乐 节
目的来 源 ，ＮＡ －１ １ Ｓ １ 的 网络 功 人 爱 用 的ＵＳ Ｂ 解 码功 能嘛 ，只 能可 分为３ 类 ，第 一 类 是 基于 要 有 了 网 络 ，还 要 笨 拙 地 外 挂
部编新人教版三年级上册1-8单元看拼音写词语(1)(1)(1)(1)复习过程
部编新人教版三年级上册1- 8 单元看拼音写词语( 1 ) ( 1 ) ( 1 ) ( 1)第一单元z do ch 印r on g qi u h cn z u xi m y cn f u zhu an g ji eb ci d a b cn chu on d C on j n g t n g zh i c u zhu C g d ^ziy n g zi lu o y e hu an g y e tiC o w u xico yu 印 j ng C------------ 1 ---------------------------------- 1 --------------- inii*III----------------- J ---------------------------------- 1 ---------------- inii----------------- 1---------------- ----------------- 1 ----------------1 ii U 1 1 [I lli h Iii |i h»sh ou b i 11 I II II II [1 II I d n g dzh a o y n zh e xi e 1 11zh en y u \1II II 1II二工卜1 [I1II H Hf I [ iu c d o~" 1C o hu eng b e i s o ng r e nao—3 ------------------------------- 1—I j ----------------------------------------------------------- 1 ~pi a o y C g k ou d i百 zh u Ii sh U zh I g u I a zh i g m yg (n g k e lan Ii 印 di a n t o u y l y i y a y a j shu ilu O sh ich u yi j i m cn g m cn g xu cn I i du o c dp ito u s cn f e( )AABB式词语：（）、（）、（）、( )( ）、（）、（）、（) 拟声词：( ）、（）、( ) 、( )( ）不（）、「（）不（）、（）不（)填动词：（）招呼（）游戏（）热闹（）功课( ) 口笛（）墙角（）孔雀舞（）学校( ）座位（）课文（）问题（）双臂( ）大手（）戒尺填入恰当的修饰词：（）的服装、（）的老师、（）的枝干（）的铜钟、（）的国旗、（）的小学、( )粉墙（）的东风、（）的灰雀、（）地背出、( )地听着泰戈尔，享誉世界的（）诗人、（）家。
112B中文资料
Previous Page | Return to Index | Next Page1/4" ENCLOSED PHONE JACKS1. Series 11*2. PC Terminal View*3. Series N11*click here to download a schematic drawing(you will need to have Adobe Acrobat installed on your system to do this)Hi-D® Jax 2- and 3-CONDUCTORHi-D Jax® 2- and 3-conductor enclosed phone jacks are ideal for panel/chassis and PC board mounting. Unitized molded housing protects springs, provides mechanical and electrical reliability, minimizes leakage and provides low capacity between springs. Mounts on .625 inch minimum centers in rows or arrays. .25 inch or .21 in inside diameter bushing types, metal or thermoplastic bushings (for insulated mounting). Insulated Hi-D Jax® jacks are specifically designed for in-circuit (insulated) mounting from mounting surface and have fully protected enclosed internal sleeve feature. Solder lugs or PC terminals may be selected.MOUNTINGJacks mount in a single .375 inch diameter hole on .625 inch minimum centers. Series11*, N11*, NS11* and S11* mount in panels up to .156 inch thick. Series L11* andNL11* (long bushing) mount in panels up to .25 inch thick. Jacks with PC terminals mount on PC boards up to .094 inch thick. Formed "shoulders" on each terminal provide stable stand-off mount. Threaded bushing permits mechanical connection to equipment panel. Mounting hardware is supplied.SERIES 11* - 2- and 3-conductor types, threaded metalbushing .276 inch long. .25 inch inside diameterbushings.SERIES L11* - Same as Series 11*, except bushing is .375inch long for mounting in panels up to .25 inch thick.SERIES N11* - Same as Series 11*, except bushing ismolded thermoplastic for insulated mounting.SERIES NL11* - Same as Series N11*, except bushingis .375 inch long for insulated mounting in panels up to.25 inch thick.SERIES S11* - Same as Series 11*, except bushing has.21 inch inside diameter. Smaller diameter protects againstaccidental insertion of plugs with .25 inch diameter fingers.ý NS11* - (SPECIAL ORDER ONLY) - Same asSeries N11*, except bushing is .21 inch inside diameter.113BPC1M AND 114BPC1M - Versatile, 3-conductor 113BPC1M and 114BPC1M feature springs which accept a wide variety of 1/4 inch plug designs. Self-aligning PC terminals allow for easier insertion into a printed circuit board. Also feature a metric thread mounting.TWO CONDUCTOR PART NUMBERSSolder Lug Part Number PC TerminalsPart NumberDescription Jack Schematic1TypicalMating Plug2111111PC Open circuit I250 N111N111PC Insulated bushing I250NL111-.375 " long insulatedbushingI250112A112APC Single closed circuit III250 L112A L112APC.375" long bushing III250 N112A N112APC Insulated bushing III250NL112A-.375" long insulatedbushingIII250113113PC Isolated "make" circuit V250 N113-Insulated bushing V250ý 113D113DPC Transfer circuit (1-C)VI 3250 113E113EPC Isolated "break" circuit IX250 THREE CONDUCTOR PART NUMBERS112B112BPC Double open circuit IV267L112B-.375" long bushing IV267 N112B N112BPC Insulated bushing IV267 NL112B-.375" long bushing IV267-S112BPC .210" inside diameterbushingIV S-267113B113BPC Single closed circuit VII267-113BPC1M Single closed circuit VII-L113B-.375" long bushing VII267 N113B N113BPC Insulated bushing VII267 NL113B-.375" long bushing VII267 113F113FPC Ring circuit closed XXVIII267 114B114BPC Double closed circuit XII267 114BPC1M Double closed circuit XII-L114B L114BPC.375" long bushing XII267 N114B N114BPC Insulated bushing XII267 NL114B NL114BPC.375" long bushing XII2671 Other circuits available; contact factory. Schematics pages 65 and 66.2 See Plug Section for other options.3 Two tip springs.ý Special order only. Contact Switchcraft.SPECIFYING NOTE:Unless otherwise shown in "Description", jacks have .276 inch long threaded bushings with .25 inch inside diameter.Hi-D Jax® 2- and 3-CONDUCTORSPECIFICATIONSMATERIALMounting Bushing: Series 11*, L11*, S11* - Nickel-plated copper alloy. Series N11*, NL11*, NS11* - Molded thermoplastic over nickel-plated copper alloy sleeve.Previous Page | Return to Index | Next PageTo search a category please click on the corresponding icon:| Connectors | Jacks and Plugs || Patch Panels, Patch Kits & Jackfields | Cable Assemblies and Patch Cords | Switches | All products shown are covered by Switchcraft's limited lifetime warranty.| Switchcraft home |About Us | Products | What's New | Search | Contact Us。
市民文体活动中心体艺健身中心提档升级项目室内背景噪声计算分析报告
第六章室内背景噪声计算分析报告项目名称：市民文体活动中心（体艺健身中心提档升级）项目项目地址：建设单位：设计单位：施工单位：规范标准参考依据：1、《绿色建筑评价标准》GB/T50378-20192、《民用建筑隔声设计规范》GB50118-20103、《建筑隔声评价标准》GB/T50121-20054、《建筑声学设计手册》（中国建筑工业出版社出版，中国建筑科学研究院建筑物理研究所主编，出版时间1987.07）5、《建筑隔声设计一空气声隔声技术》（中国建筑工业出版社出版，康玉成主编，出版时间：2004.10）6、《民用建筑热工设计规范》GB50176-20167、《建筑隔声与吸声构造》08J931一.建筑概况1.1基本信息城市：邛喇北纬二30.70。
，东经=IO4.00。
)建筑类型：公建建筑朝向：南偏东151度建筑层数：地上2层，地下0层建筑物高度：11.00m1.2层高汇总表1.3建筑轴测图二、指标要求针对建筑室内背景噪声性能的评价标准主要为《绿色建筑评价标准》GB/T50378-2019第5.1.4条第一款控制项及第526条评分项的要求,评价分值8分。
具体条目如下：5.1.4条第一款主要功能房间的室内噪声级应满足现行国家标准《民用建筑隔声设计规范》GB50118中的低限要求。
【控制项】5.2.6采取措施优化主要功能房间的室内声环境，评价总分值为8分。
【评分项】1噪声级达到现行国家标准《民用建筑隔声设计规范》GB50118中的低限标准限值和高要求标准限值的平均值，得4分；2达到高要求标准限值，得8分。
三.计算原理允许噪声级是室内噪声容许标准，一般可以用NR评价曲线或A声级来规定。
NR评价曲线是人为规定的各频带(从低频到高频)噪声声压级曲线，往往用它检查哪些频带的噪声有问题。
在通常的声级范围内，A 声级与人们对声源响度的主观感觉有良好的相关性，使用简便，是被广泛采用的单值评价方法。
本项目根据《民用建筑隔声设计规范》GB50118的要求，使用A声级作为考察指标，综合考虑了组合构件的隔声量、房间吸声、孔洞缝隙及多噪声源的影响，最终确定室内的背景噪声值。
三菱PLC指令详解资料
一顺控指令1触点指令00 LD逻辑操作开始01 LDI逻辑非操作开始02 AND逻辑乘03 ANI逻辑乘非04 OR逻辑加05 ORI逻辑加非2连接指令06 ANB AND逻辑块与07 ORB OR逻辑块或08 MPS储藏操作结果09 MRD从MPS读取操作结果10 MPP从MPS读取操作结果并除去结果3输出指令11 OUT软元件输出12 SET软元件置位13 RST软元件复位14 PLS在输入信号的上升沿15 PLF在输入信号的下降沿16 CHK软元件输出翻转4移位指令17 SFT元件移1位18 SFTP元件移1位5主控指令19 MC主控开始20 MCR主控复位6结束指令21 FEND结束主程序22 END总的程序尾端，返回第 0步7其他指令23 STOP停止24 NOP空操作二基本指令1比较指令16位数据比较25 LD=当S1=S2,接通，当 S1≠S2, 断开26AND=27OR=28LD<> 当 S1≠S2, 接通，当S1=S2, 断开29AND<>30OR<>31LD> 当 S1>S2, 接通，当S1≤S2, 断开32AND>33OR>34LD<= 当 S1≤S2, 接通，当S1>S2, 断开35AND<=36OR<=37LD< 当 S1<S2, 接通，当S1≥S2, 断开38AND<39OR<40LD>= 当 S1≥S2, 接通，当S1<S2, 断开41AND>=42OR>=32位数据比较43 LDD=当(S1+1,S1)=(S2+1,S2),接通44ANDD=45ORD=46 LDD<>当(S1+1,S1)≠(S2+1,S2),接通47ANDD<>48ORD<>49LDD> 当(S1+1,S1)>(S2+1,S2), 接通50ANDD>51ORD>52LDD<= 当 (S1+1,S1) ≤(S2+1,S2), 接通53ANDD<=54ORD<=55LDD< 当(S1+1,S1)<(S2+1,S2), 接通56ANDD<57ORD<58LDD>= 当 (S1+1,S1) ≥(S2+1,S2), 接通59ANDD>=60ORD>=2算术运算指令二进制 16 位加/减61 + (D)+(S)→ (D)62+P63+ (S1)+(S2) →(D)64+P65- (D)-(S) → (D)66-P67- (S1)-(S2) →(D)68-P二进制 32 位加/减69 D+ (D+1,D)+(S+1,S)→ (D+1,D) 70D+P71D+ (S1+1,S1)+(S2+1,S2)→(D+1,D) 72D+P73 D- (D+1,D)-(S+1,S)→ (D+1,D)74D-P75D- (S1+1,S1)-(S2+1,S2) →(D+1,D) 76D-P77* (S1) ×(S2) →(D+1,D)78*P79/ (S1)/(S2) →商 (D), 余数 (D+1)80/P81D* (S1+1,S1) ×(S2+1,S2) →(D+3,D+2,D+1,D)82D*P83D/ (S1+1,S1)/(S2+1,S2) →商(D+1,D), 余数 (D+3,D+2)84D/P85 B+ (D)+(S)→(D)86B+P87B+ (S1)+(S2) →(D)88B+P89B- (D)-(S) →(D)90B-P91B- (S1)-(S2) →(D)92B-P93 DB+ (D+1,D)+(S+1,S)→(D+1,D) 94DB+P95DB+ (S1+1,S1)+(S2+1,S2)→(D+1,D) 96DB+P97DB- (D+1,D)-(S+1,S) →(D+1,D)98DB-P99DB- (S1+1,S1)-(S2+1,S2) →(D+1,D) 100DB-P101B* (S1) ×(S2) →(D+1,D)102B*P103B/ (S1)/(S2) →商 (D), 余数 (D+1) 104B/P105DB* (S1+1,S1) ×(S2+1,S2) →(D+3,D+2,D+1,D)106DB*P107DB/ (S1+1,S1)/(S2+1,S2) →商(D+1,D), 余数 (D+3,D+2)108DB/P109INC (D)+1 → (D)110INCP111 DINC (D+1,D)+1→(D+1,D) 112DINCP113DEC (D)-1 →(D)114DECP115 DDEC (D+1,D)-1→(D+1,D) 116 DDECP3 BCD —二进制变换117 BCD (S) → (D)BCD 变换118BCDP119DBCD (S+1,S) →(D+1,D) 120DBCDP121BIN (S) →(D) 二进制变换122BINP123DBIN (S+1,S) →(D+1,D)124DBINP4数据传达指令125 MOV (S)→(D)126MOVP127DMOV (S+1,S) → (D+1,D)128DMOVP129CML (S) →(D)130CMLP131DCML (S+1,S) → (D+1,D)132DCML133DCMLP134BMOV (S) →(D)n 个135BMOVP136FMOV (S) →(D)n 个137FMOVP138XCH (D1) ←→ (D2)139XCHP140 DXCH (D1+1,D1)←→ (D2+1,D2) 141 DXCHP5程序分支指令142 CJ条件满足，跳转到P** 处143 SCJ条件满足后紧接的扫描周期,跳转到 P** 处144 JMP无条件跳转到P** 处145 CALL执行P**处子程序146CALLP147RET 从子程序返回148EI 赞同中断149DI 禁止中断150IRET 从中断程序返回151SUB 执行 n 指定的程序152SUBP6程序切换指令153 CHG在主副程序间切换7刷新指令154 COM执行通讯刷新155 EI赞同通讯刷新156 DI禁止通讯刷新157 SEG对应软元件的刷新，仅执行1个扫描周期，M9052 ON时有效三应用指令1逻辑运算指令158 WAND (D) AND (S)→ (D)159 WANDP160 WAND (S1) AND (S2)→(D)161 WANDP162 DAND (D+1,D) AND (S+1,S)→(D+1,D) 163 DANDP164 WOR (D) OR (S)→(D)165 WORP166 WOR (S1) OR (S2)→(D)167 WORP168 DOR (D+1,D) OR (S+1,S)→ (D+1,D) 169 DORP170 WXOR (D) XOR (S)→(D) 异或171 WXORP172 WXOR (S1) XOR (S2)→(D)173 WXORP174 DXOR (D+1,D) XOR (S+1,S)→(D+1,D) 175 DXORP176 WXNR (D) XOR (S)→(D)177 WXNRP178 WXNR (S1) XOR (S2)→(D)179 WXNRP180 DXNR (D+1,D) XOR (S+1,S)→(D+1,D) 181DXNRP182NEG 0-(D) →(D) 补码183NEGP2旋转指令184 ROR n位右转185RORP186RCR n 位右转 (带进位 ) 187RCRP188ROL n 位左转189ROLP190RCL n 位左转 (带进位 ) 191RCLP192DROR n 位右转193DRORP194DRCR n 位右转 (带进位 ) 195DRCRP196DROL n 位左转197DROLP198DRCL n 位左转 (带进位 ) 199DRCLP3移位指令200 SFR n 位右移201SFRP202SFL n 位左移203SFLP204 BSFR 1 位右移205BSFRP206BSFL 1 位左移207BSFLP208DSFR 1 位右移209DSFRP210DSFL 1 位左移211DSFLP4数据办理指令212 SER数据找寻213SERP214SUM 位检查215SUMP216DSUM217DSUMP218DECO 译码编码219DECOP220ENCO221ENCOP222SEG 7 段编码223BSET 对字中 n 地址位224BSETP225 BRST对字中n位复位226BRSTP227DIS 组合分别228DISP229UNI230UNIP231ASC ASCII 转变5先进先出指令232 FIFW FIFO写233FIFWP234FIFR FIFO 读235FIFRP6内存缓冲区存取指令236 FROM从特别功能模块读取数据237FROMP238DFRO239DFROP240TO 向特别功能模块写数据241TOP242DTO243FROM 从远程 I/O 站读数据244FROMP245DFRO246DFROP247TO 向远程站写数据248TOP249DTO250DTOP7 FOR/NEXT指令251 FOR重复n次252 NEXT8 当地站、远程I/O 站存取指令253 LRDP从当地站读数据254 LWTP向当地站写数据255 RFRP从远程特别功能模块读数据256 RTOP向远程特别功能模块写数据9显示指令257 PR从指定的8点字软元件输出16 个字符的 ASCII 码258 PR序次向输出模块输出ASCII 码 , 直到结束符 NUL(00H)259 PRC将字软元件的说明变换成ASCII 码，并输出260 LED将指定的8点字软元件显示16 个字符的 ASCII 码261 LEDA显示指定的英文数字字符262LEDB263LEDC 显示软元件 S 的说明264LEDR 显示复位10其他指令265 WDT WDT复位266WDTP267CHK 故障检测268SLT 按参数设定的条件 ,数据被锁定269SLTR 状态锁存复位，且执行 SLT 270STRA 按参数设定的条件 ,采样数据存入271STRAR 采样追踪复位，且赞同执行272STC 进位标志 (M9012)ON273CLC 进位标志 (M9012)OFF274DUTY 用户定义时钟11伺服指令275 DSFRP央求启动伺服程序276 PSFLP数据更正特别继电器和特别存放器一特别继电器M 清单M9000熔丝断M9002 I/O组件校验出错M9004 MINI网通讯出错M9005 AC电源掉电检测M9006电池电压低M9007电池电压低锁存M9008自诊断出错M9009信号报警器检测M9010运算出错标志M9011运算出错标志锁存M9012进位标志M9016数据储藏区清零标志M9017数据储藏区清零标志M9018数据通讯监控切换M9020 0号用户准时时钟M9021 1号用户准时时钟M9022 2号用户准时时钟M9023 3号用户准时时钟M9024 4号用户准时时钟M9025时钟数据设置央求M9026时钟数据出错M9027时钟数据显示M9028时钟数据读央求秒时钟秒时钟M9032 1秒时钟M9033 2秒时钟M9034 1分钟时钟M9036常开M9037常闭M9038 RUN后第一个扫描周期ON M9039运行标志M9040 暂停 PAUSE 赞同线圈M9041 PAUSE状态触点M9042停止状态触点M9043采样追踪完成M9044采样追踪M9046采样追踪M9047采样追踪准备M9048 RUN LED闪烁标志M9049切换输出字符数量M9050存放操作结果的储藏区交换触点M9051 CHG指令执行禁止M9052 SEG指令切换M9053 EI/DI指令切换M9054单步运行标志M9055状态锁存完成标志M9056 主程序 P, I 设置央求M9057 副程序 P, I 设置程序M9060 副程序 2P, I 设置程序M9061 副程序 3P, I 设置程序M9060远程终端出错M9061通讯出错M9065分别传达状态M9066传达办理切换M9067 I/O组件出错检测M9068测试模式M9069线路故障时的输出M9073 WDT出错标志M9074 PCPU准备完成标志M9075测试模式标志M9076外面急停输入标志M9077手动脉冲发生器轴设置错误标志M9078测试模式央求出错标志M9079伺复程序设置出错标志M9081对远程模块的通讯央求M9082最后站数不一致M9084出错检测M9086运行标志 BASIC 程序M9087暂停 (PAUSE) 标志M9091操作运行出错细节标志M9091微机子程序调用出错标志M9092双电源模块过热M9093双工电源模块出错M9094I/O改变标志M9095双工运行校验出错M9096A3VCPU A自校出错M9097A3VCPU B自校出错M9098A3VCPU C自校出错M9099A3VTU 自校出错M9100SFC程序登记M9101SFC程序起 /停M9102SFC启动状态M9103连续步转移有效 / 无效M9104连续转移防范标志M9108步转移监控准时器初步( 对应 D9108)M9109步转移监控准时器初步( 对应 D9109)M9110步转移监控准时器初步( 对应 D9110)M9111步转移监控准时器初步( 对应 D9111)M9112步转移监控准时器初步( 对应 D9112)M9113步转移监控准时器初步( 对应 D9113)M9114步转移监控准时器初步( 对应 D9114)M9180激活步采样追踪完成标志M9181激活步采样追踪执行标志M9182激活步采样追踪有效M9196在块停止时控制输出M9197~9198保险丝熔断，I/O校核出错显示切换二特别存放器D9000保险丝断D9001保险丝断D9002 I/O组件校验出错D9003 SUM指令检测位数D9004 MINI网主通讯组件出错D9005 AC掉电计数D9006电池不足D9008自诊断出错D9009信号报警器检测D9010出错步D9011出错步D9014 I/O控制模式D9015 CPU运行状态D9016 ROM/RAM设置D9017最小扫描时间D9018当前扫描时间D9019最大扫描时间D9020恒定扫描D9021扫描时间D9022 1秒计数器D9025 时钟数据 (年，月 )D9026 时钟数据 (日，时 )D9027 时钟数据 (分，秒 )D9028 时钟数据 (星期 )D9021~D9034远程终端组件参数设置D9035 远程 I/O 组件的通讯属性D9035扩展文件存放器D9036总的站数D9036~9037供指定扩展文件存放器软件地址D9038~9039 LED显示优先级D9044采样追踪D9050 SFC程序出错代码D9051出错块D9052出错步D9053转移出错D9054出错顺控步D9055状态锁存步序号D9061通讯出错代码D9072 PC通讯检测D9081对远程终端模块的已执行的通讯央求数D9082最后的站号D9090微机子程序输入数据区首软元件号D9091指令出错D9094 待更换的 I/O 组件的首地址D9095 A3VTS系统和A3VCPU的运行状态D9096 A3VCPU A自检出错D9097A3VCPU B自检出错D9098A3VCPU C自检出错D9099A3VTU 自检测出错D9100~D9107断保险丝的组件D9100保险丝熔断的组件D9108~D9114步转移监控准时器设置D9116~D9123 I/O组件校验出错D9124信号器报警数量检测D9125~D9132信号报警器地址号D9133~D9140远程终端卡信息D9141~D9172通讯重发次数D9173模式设置D9174设置重发次数D9175线缆出错模块出错代码D9180~9193远程终端模块出错代码D9180 轴 1 和轴 2 的限位开关输出状态储藏区D9181 轴 3 和轴 4 的限位开关输出状态储藏区D9182 轴 5 和轴 6 的限位开关输出状态储藏区D9183 轴 7 和轴 8 的限位开关输出状态储藏区D9184 CPU出错的原因D9185伺服放大器接线数据D9187手动脉冲发生器轴设置出错D9188在TEST模式下启动轴号央求出错D9189出错程序号D9190数据设置出错D9191伺服放大器种类D9196~9199故障站检测D9200LRDP办理结果D9201LWTP办理结果D9204通讯状态D9205执行回送的站D9206执行回送的站D9207通讯扫描时间 (最大值 )D9208通讯扫描时间 (最小值 )D9209通讯扫描时间 (当前值 )D9210重发次数D9211环路切换计数D9212就地站运行状态 (1~16)D9213就地站运行状态 (17~32)D9214就地站运行状态 (33~48)D9215 就地站运行状态 (49~64)D9216 就地站出错检测 (1~16)D9217 就地站出错检测 (17~32)D9218 就地站出错检测 (33~48)D9219 就地站出错检测 (49~64)D9220 就地站参数不般配或(1~16)远程站 I/O 分配出错D9221 就地站参数不般配或(17~32)远程站 I/O 分配出错D9222 就地站参数不般配或(33~48)远程站 I/O 分配出错D9223 就地站参数不般配或(49~64)远程站 I/O 分配出错D9224 主站与从站和远程I/O 站之间的初始通讯 (1~16)D9225 主站与从站和远程I/O 站之间的初始通讯 (17~32)D9226 主站与从站和远程I/O 站之间的初始通讯 (33~48)D9227 主站与从站和远程I/O 站之间的初始通讯 (49~64)D9228 就地站或远程I/O 站出错 (1~16)D9229就地站或远程 I/O 站出错 (17~32) D9230就地站或远程 I/O 站出错 (33~48) D9231就地站或远程 I/O 站出错 (49~64) D9232就地站或远程 I/O 站环路出错D9233就地站或远程 I/O 站环路出错D9234就地站或远程 I/O 站环路出错D9235就地站或远程 I/O 站环路出错D9236就地站或远程 I/O 站环路出错D9237就地站或远程 I/O 站环路出错D9238就地站或远程 I/O 站环路出错D9239就地站或远程 I/O 站环路出错D9240检测到接收出错的次数D9243本站站号检测D9244从站的总数D9245检测到的接收出错次数D9248就地站运行状态D9249就地站运行状态D9250就地站运行状态D9251就地站运行状态D9252就地站出错检测D9253就地站出错检测D9254就地站出错检测D9255就地站出错检测各种软元件一览表项目 A1,A1NA1S A2,A2NA2C A2-S1A2N-S1 A3,A3NA3A A 2U,A3UA4UI/O 软元件点 256 512 1024 2048 8192输入继电器 X 0~FF 0~1FF 0~3FF 0~7FF 0~FFF输出继电器 Y 0~FF 0~1FF 0~3FF 0~7FF 0~FFF辅助继电器内部继电器(1000点)M0~M999 M0~M999, M2 048~8191特别继电器(256 点 )M9000~M9255锁存继电器(1048 点 )L1000~L2048通讯用继电器(2048 点)B0~B3FF B0~BFFF准时器 100ms准时器(200点)T0~T19910ms 准时器 (56 点)T200~T255100ms记忆准时器(0 点 )计数器 (256 点)C0~C255存放器数据存放器 (1024 点)D0~D1023 D0~D6143特别存放器(256 点 )D9000~D9255通讯存放器(1024 点 )W0~W3FF W0~WFFF累加器 (2 点)A0,A1变址存放器 (2 点 )Z, V Z,Z1~Z6(7点), V,V1~V6(7点)嵌套 (8 点 )N0~ N7指针 (256 点)P0~P255中断指针 (32 点)I0~I31常数十进制K (16 位)-32768~+32767(32 位 )-2147483648 ~+2147483647十六进制 H (16 位 )0~FFFF(32 位 )0~FFFFFFFF。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.
5,000
(1) For highest possible read-out coverage, operate readers at a modulation depth of 20% or higher. (2) After integration into paper (3) After PVC lamination
Delivery
Typical quantity of good units per reel
PART NUMBER
RI-I11-114A-S1
RI-I11-114B-S1
ISO/IEC 15693-2, -3; ISO/IEC 18000-3
13.56 MHz
13.86 MHz ± 200 kHz (includes frequency offset to compensate further integration into
The Tag-it HF-I Pro transponder inlays are manufactured with TI’s patented laser tuning process to provide consistent read performance. Prior to delivery, the transponders undergo complete functional and parametric testing, in order to provide the high quality that customers have come to expect from TI.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
(Anti-Collision)
• Password Protected Write Command • Command to Disable IC Functionality
APPLICATIONS
• Product Authentication • Ticketing • Stored Value
Supported standard Recommended operating frequency
Passive resonance frequency (at 25°C)
Typical required activation field strength to read (at 25°C) Typical required activation field strength to write (at 25°C) Factory-programmed read-only number Memory (user programmable) Typical programming cycles (at 25°C) Data retention time (at 55°C) Simultaneous identification of tags Antenna size Foil width Foil pitch Base material Operating temperature Storage temperature (single inlay) Storage temperature (on reel)
0x08 0x09
0x0A
0x0B
RI-I11-114A-S1, RI-I11-114B-S1
SCBS822 – NOVEMBER 2006
MEMORY ORGANIZATION
32 bits
Lock Bits FU
F = Factory Lock, U = User Lock
User data (256 bits)
X
UID Number
(64 bits)
AFI Password
Submit Documen交易网
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
元器件交易网
RI-I11-114A-S1, RI-I11-114B-S1
Tag-it™ HF-I PRO TRANSPONDER INLAYS SQUARE
SCBS822 – NOVEMBER 2006
FEATURES
• ISO/IEC 15693-2, -3; ISO/IEC 18000-3 Compliant
Copyright © 2006, Texas Instruments Incorporated
元器件交易网
RI-I11-114A-S1, RI-I11-114B-S1
SCBS822 – NOVEMBER 2006
SPECIFICATIONS (1)
paper)
14.4 MHz ± 200 kHz (includes frequency offset to
compensate PVC lamination)
98 dBµA/m(2)
98 dBµA/m(3)
101 dBµA/m(2)
101 dBµA/m(3)
64 bits
256 bits organized in 8-bit × 32-bit blocks
DESCRIPTION
Texas Instruments Tag-it™ HF-I Pro transponder inlays consist of 13.56-MHz high-frequency (HF) transponders that are compliant with the ISO/IEC 15693 and ISO/IEC 18000-3 global open standards. These products offer a user-accessible memory of 256 bits, organized in eight blocks, and an extended command set including password protect write available in five different antenna shapes, with frequency offset for integration into paper, PVC, or other substrates.
SUPPORTED COMMAND SET
REQUEST
REQUEST MODE(1)
REQUEST CODE INVENTORY ADDRESSED NON-ADDRESSED
AFI
OPT. FLAG
ISO 15693 Mandatory and Optional Commands
Inventory
Substrate: PET (polyethylenetherephtalate); Antenna: aluminum