AT070TN94_v1

合集下载

群创7寸数字屏规格书

The copyright belongs to InnoLux. Any unauthorized use is prohibited.INNO L U X DISPLAY CORPORATIONLCD MODULESPECIFICATIONCustomer: Model Name: AT070TN94SPEC NO.: A070-94-TT-01 Date: 2009/12/02 Version:01□Preliminary Specification ■Final SpecificationFor Customer ’s AcceptanceApproved byCommentApproved byReviewed by Prepared byJoe Lin2009/12/08James Yu2009/12/08David Lee2009/12/02InnoLux copyright 2004All rights reserved,Copying forbidden.Record of RevisionVersion Revise Date Page ContentPre-Spec.01 2009/07/07 All Initial ReleaseFinal-spec.01 2009/12/02 All The first version final specification.6 Modify V COM to 3.8V(Typ.), 3.6V(Min.) and 4.0V(Max.).9 Add Input Clock and Data Timing Diagram.18 Update the Mechanical Drawing.The copyright belongs to InnoLux. Any unauthorized use is prohibited.I NNO L U XContents1. General Specifications (1)2. Pin Assignment (2)3. Operation Specifications (5)3.1. Absolute Maximum Ratings (5)3.1.1. Typical Operation Conditions (6)3.1.2. Current Consumption (7)3.1.3. Backlight Driving Conditions (7)3.2. Power Sequence (8)3.3. Timing Characteristics (9)3.3.1. AC Electrical Characteristics (9)3.3.2. Input Clock and Data Timing Diagram (9)3.3.3. Timing (10)3.3.4. Data Input Format (11)4. Optical Specifications (12)5. Reliability Test Items (16)6. General Precautions (17)6.1. Safety (17)6.2. Handling (17)6.3. Static Electricity (17)6.4. Storage (17)6.5. Cleaning (17)7. Mechanical Drawing (18)8. Package Drawing (19)8.1. Packaging Material Table (19)8.2. Packaging Quantity (19)8.3. Packaging Drawing (20)The copyright belongs to InnoLux. Any unauthorized use is prohibited.1. General SpecificationsNo. Item Specification Remark1 LCD size 7.0 inch(Diagonal)2 Driver element a-Si TFT active matrix3 Resolution 800 × 3(RGB) × 4804 Display mode Normally White, Transmissive5 Dot pitch 0.0642(W) × 0.1790(H) mm6 Active area 154.08(W) × 85.92(H) mm7 Module size 164.9(W) ×100.0(H) ×5.7(D) mm Note 18 Surface treatment Anti-Glare9 Color arrangement RGB-stripe10 Interface Digital11 Backlight power consumption 1.674W (Typ.)12 Panel power consumption 0.226W (Typ.)13 Weight 150g (Typ.)Note 1: Refer to Mechanical Drawing.2. Pin AssignmentFPC Connector is used for the module electronics interface. The recommended model is FH12A-50S-0.5SH manufactured by Hirose.Pin No. Symbol I/O Function Remark1 V LED+P Power for LED backlight (Anode)2 V LED+P Power for LED backlight (Anode)3 V LED-P Power for LED backlight (Cathode)4 V LED-P Power for LED backlight (Cathode)5 GND P Power ground6 V COM I Common voltage7 DV DD P Power for Digital Circuit8 MODE I DE/SYNC mode select Note 19 DE I Data Input Enable10 VS I Vertical Sync Input11 HS I Horizontal Sync Input12 B7 I Blue data(MSB)13 B6 I Blue data14 B5 I Blue data15 B4 I Blue data16 B3 I Blue data17 B2 I Blue data18 B1 I Blue data Note 219 B0 I Blue data(LSB) Note 220 G7 I Green data(MSB)21 G6 I Green data22 G5 I Green data23 G4 I Green data24 G3 I Green data25 G2 I Green data26 G1 I Green data Note 227 G0 I Green data(LSB) Note 228 R7 I Red data(MSB)29 R6 I Red data30 R5 I Red data31 R4 I Red data32 R3 I Red data33 R2 I Red data34 R1 I Red data Note 235 R0 I Red data(LSB) Note 236 GND P Power Ground37 DCLK I Sample clock Note 338 GND P Power Ground39 L/R I Left / right selection Note 4,540 U/D I Up/down selection Note 4,541 V GH P Gate ON Voltage42 V GL P Gate OFF Voltage43 AV DD P Power for Analog Circuit44 RESET I Global reset pin. Note 645 NC - No connection46 V COM I Common Voltage47 DITHB I Dithering function Note 748 GND P Power Ground49 NC - No connection50 NC - No connectionI: input, O: output, P: PowerNote 1: DE/SYNC mode select. Normally pull high.When select DE mode, MODE=”1”, VS and HS must pull high.When select SYNC mode,MODE= ”0”, DE must be grounded.Note 2: When input 18 bits RGB data, the two low bits of R,G and B data must be grounded.Note 3:Data shall be latched at the falling edge of DCLK.Note 4: Selection of scanning modeSetting of scan control inputU/D L/R Scanning direction GND DV DD Up to down, left to right DV DD GND Down to up, right to left GND GND Up to down, right to left DV DDDV DDDown to up, left to rightNote 5: Definition of scanning direction. Refer to the figure as below:Note 6: Global reset pin. Active low to enter reset state. Suggest to connect with an RCreset circuit for stability. Normally pull high.Note 7: Dithering function enable control, normally pull high. When DITHB=”1”,Disable internal dithering function, When DITHB=”0”,Enable internal dithering function,RightLeft DownUp3. Operation Specifications3.1. Absolute Maximum Ratings(Note 1)ValuesItem SymbolMin. Max.Unit RemarkDV DD -0.3 5.0 VAV DD 6.5 13.5 VV GH -0.3 40.0 VV GL -20.0 0.3 V Power voltageV GH-V GL- 40.0 V Operation Temperature T OP -30 85 ℃Storage Temperature T ST-30 85 ℃LED Reverse Voltage V R- 1.2 VEach LEDNote 2 LED Forward Current I F- 25 mA Each LEDNote 1: The absolute maximum rating values of this product are not allowed to be exceeded at any times. Should a module be used with any of the absolute maximum ratingsexceeded, the characteristics of the module may not be recovered, or in an extremecase, the module may be permanently destroyed.Note 2: V R Conditions: Zener Diode 20mA3.1.1. Typical Operation Conditions( Note 1)ValuesUnit Remark Item SymbolMin. Typ. Max.DV DD 3.0 3.3 3.6 V Note 2AV DD 10.2 10.4 10.6 VPower voltageV GH 15.3 16.0 16.7 VV GL -7.7 -7.0 -6.3 VInput signal voltage V COM 3.6 3.8 4.0 VInput logic high voltage V IH 0.7 DV DD - DV DD VNote 3 Input logic low voltage V IL 0 - 0.3 DV DD VNote 1: Be sure to apply DV DD and V GL to the LCD first, and then apply V GH.Note 2: DV DD setting should match the signals output voltage (refer to Note 3) of customer’s system board.Note 3: DCLK,HS,VS,RESET,U/D, L/R,DE,R0~R7,G0~G7,B0~B7,MODE,DITHB.3.1.2. Current ConsumptionValuesItem SymbolMin. Typ. Max.Unit RemarkI GH - 0.2 1.0 mA V GH =16.0VI GL - 0.2 1.0 mA V GL = -7.0V IDV DD - 4.0 10 mA DV DD =3.3VCurrent for DriverIAV DD - 20 50 mA AV DD =10.4V3.1.3. Backlight Driving ConditionsValuesItem SymbolMin. Typ. Max.Unit Remark Voltage for LED backlight V L 8.4 9.3 10.2 V Note 1 Current for LED backlight I L 170 180 200 mALED life time - 20,000 - - Hr Note 2Note 1: The LED Supply Voltage is defined by the number of LED at Ta=25℃ andI L =180mA.Note 2: The “LED life time” is defined as the module brightness decrease to 50% original brightness at Ta=25℃ and I L =180mA. The LED lifetime could be decreased ifoperating I L is lager than 180mA.3.2. Power Sequencea. Power on:Note: Data include R0~R7, B0~B7, GO~G7, U/D, L/R, DCLK, HS,VS,DE.DV DD→VGL→AVDD→VGH→Data→B/LB/L→Data→VGH→AVDD→VGL→DV DD3.3. Timing Characteristics3.3.1. AC Electrical CharacteristicsValuesItem SymbolMin. Typ. Max.Unit Remark HS setup time T hst8 - - nsHS hold time T hhd 8 - - nsVS setup time T vst8 - - nsVS hold time T vhd8 - - nsData setup time T dsu8 - - nsData hole time T dhd8 - - nsDE setup time T esu 8 - - nsDE hole time T ehd8 - - nsDV DD Power On Slew rate T POR - - 20 ms From 0 to 90% DV DDRESET pulse width T Rst 1 - - ms DCLK cycle time T coh 20 - - ns DCLK pulse duty T cwh 40 50 60 %3.3.2. Input Clock and Data Timing Diagram3.3.3. TimingValuesUnit Remark Item SymbolMin. Typ. Max.Horizontal Display Area thd- 800 - DCLKDCLK Frequency fclk26.4 33.3 46.8 MHzOne Horizontal Line th862 1056 1200 DCLKHS pulse width thpw 1 - 40 DCLKHS Blanking thb46 46 46 DCLKHS Front Porch thfp 16 210 354 DCLKValuesItem SymbolUnit RemarkMin. Typ. Max.Vertical Display Area tvd- 480 - THVS period time tv 510 525 650 THVS pulse width tvpw 1 - 20 THVS Blanking tvb23 23 23 THVS Front Porch tvfp7 22 147 TH3.3.4. Data Input Format4. Optical SpecificationsValuesItem Symbol ConditionMin. Typ. Max.Unit RemarkθL Φ=180°(9 o’clock) 60 70 -θRΦ=0°(3 o’clock) 60 70 -θTΦ=90°(12 o’clock) 40 50 -Viewing angle(CR≥ 10)θBΦ=270°(6 o’clock) 60 70 -degree Note 1T ON - 10 20 msec Note 3 Response timeT OFF - 15 30 msec Note 3 Contrast ratio CR 400 500 - - Note 4W X 0.26 0.31 0.36 -Color chromaticityW Y 0.28 0.33 0.38 -Note 2Note 5Note 6 Luminance L 320 400 - cd/m² Note 6 LuminanceuniformityY UNormalθ=Φ=0°70 75 - % Note 7Test Conditions:1. DV DD=3.3V, I L=180mA (Backlight current), the ambient temperature is 25℃.2. The test systems refer to Note 2.Note 1: Definition of viewing angle rangeFig. 4-1 Definition of viewing angleNote 2: Definition of optical measurement system.The optical characteristics should be measured in dark room. After 30 minutesoperation, the optical properties are measured at the center point of the LCD screen. (Response time is measured by Photo detector TOPCON BM-7, other items are measured by BM-5A/Field of view: 1° /Height: 500mm.)Normal line θ=Φ=0°Photo detectorΦ=90°12 o’clock directionΦ=270° 6 o’clock directionΦ=0°Φ=180°Active Area500mmLCMNormal line θ=Φ=0°Φ=90°12 o’clock directionΦ=270°6 o’clock directionΦ=0°Φ=180°Active AreaθLθTθBθRLCMNote 3: Definition of Response timeThe response time is defined as the LCD optical switching time interval between“White” state and “Black” state. Rise time (T ON) is the time between photo detector output intensity changed from 90% to 10%. And fall time (T OFF) is the timebetween photo detector output intensity changed from 10% to 90%.Fig. 4-3 Definition of response timeNote 4: Definition of contrast ratiostateBlack""theonLCDwhenmeasuredLuminancestateWhite""theonLCDwhenmeasuredLuminance(CR)ratioContrast=Note 5: Definition of color chromaticity (CIE1931)Color coordinates measured at center point of LCD.Note 6: All input terminals LCD panel must be ground while measuring the center area of the panel.The LED driving condition is I L=180mA .90%10%0%Photodetectoroutput(Relativevalue)ONTWhite (TFT OFF) Black (TFT ON) White (TFT OFF)Note 7:Definition of Luminance UniformityActive area is divided into 9 measuring areas (Refer to Fig. 4-4 ).Every measuring point is placed at the center of each measuring area.maxminBB(Yu)UniformityLuminance=L-------Active area length W----- Active area widthWW/3W/3W/6L/3L/3L/6LFig. 4-4 Definition of measuring pointsB max: The measured maximum luminance of all measurement position.B min: The measured minimum luminance of all measurement position.5. Reliability Test Items(Note3)Item Test Conditions Remark High Temperature Storage Ta = 85℃240hrs Note 1，Note 4 Low Temperature Storage Ta = -30℃240hrs Note 1，Note 4 High Temperature Operation Ts = 85℃240hrs Note 2，Note 4 Low Temperature Operation Ta = -30℃240hrs Note 1，Note 4 Operate at High Temperatureand Humidity+60℃, 90%RH 240hrs Note 4Thermal Shock -30℃/30 min ~ +85℃/30 min for a total 100cycles, Start with cold temperature and endwith high temperature.Note 4Vibration Test Frequency range:10~55Hz Stroke:1.5mmSweep:10Hz~55Hz~10Hz2 hours for each direction of X. Y. Z.(6 hours for total)Mechanical Shock 100G 6ms,±X, ±Y, ±Z 3 times for each directionPackage Vibration Test Random Vibration :0.015G*G/Hz from 5-200HZ, -6dB/Octave from 200-500HZ2 hours for each direction of X. Y. Z.(6 hours for total)Package Drop Test Height:60 cm1 corner, 3 edges, 6 surfacesElectro Static Discharge ± 2KV, Human Body Mode, 100pF/1500ΩNote 1: Ta is the ambient temperature of samples.Note 2: Ts is the temperature of panel’s surface.Note 3: In the standard condition, there shall be no practical problem that may affect the display function. After the reliability test, the product only guarantees operation,but don’t guarantee all of the cosmetic specification.Note 4: Before cosmetic and function test, the product must have enough recovery time, at least 2 hours at room temperature.6. General Precautions6.1. SafetyLiquid crystal is poisonous. Do not put it in your mouth. If liquid crystal touches your skin or clothes, wash it off immediately by using soap and water.6.2. Handling1. The LCD panel is plate glass. Do not subject the panel to mechanical shock or toexcessive force on its surface.2. The polarizer attached to the display is easily damaged. Please handle it carefullyto avoid scratch or other damages.3. To avoid contamination on the display surface, do not touch the module surfacewith bare hands.4. Keep a space so that the LCD panels do not touch other components.5. Put cover board such as acrylic board on the surface of LCD panel to protect panelfrom damages.6. Transparent electrodes may be disconnected if you use the LCD panel underenvironmental conditions where the condensation of dew occurs.7. Do not leave module in direct sunlight to avoid malfunction of the ICs.6.3. Static Electricity1. Be sure to ground module before turning on power or operating module.2. Do not apply voltage which exceeds the absolute maximum rating value.6.4. Storage1. Store the module in a dark room where must keep at 25±10℃ and 65%RH or less.2. Do not store the module in surroundings containing organic solvent or corrosivegas.3. Store the module in an anti-electrostatic container or bag.6.5. Cleaning1. Do not wipe the polarizer with dry cloth. It might cause scratch.2. Only use a soft sloth with IPA to wipe the polarizer, other chemicals mightpermanent damage to the polarizer.7. Mechanical Drawing8. Package Drawing8.1. Packaging Material TableNo. ItemModel(Material)Dimensions(mm)UnitWeight(kg)Quantity Remark1 LCMModuleAT070TN94 164.9 × 100.0 × 5.7 0.150 50pcs2 Partition BC Corrugatedpaper512 × 349 × 226 1.466 1set3 CorrugatedPaperB Corrugatedpaper510 × 350 0.071 4pcs4 CorrugatedBarB Corrugatedpaper512 × 11 × 3 0.046 4pcs5 Dust-ProofBagPE 700 × 530 0.048 1pcs6 A/S Bag PE 180 × 133 × 0.2 0.002 50pcs7 Carton Corrugatedpaper530 × 355 × 255 1.100 1pcs8 Total weight 10.682 kg± 5%8.2. Packaging QuantityTotal LCM quantity in Carton: no. of Partition 2 Rows × quantity per Row 25 = 508.3. Packaging Drawing。

Motorola 3.5 kHz 产品说明书

RVN4126 3.59100-386-9100-386/T DEVICERVN41772-CD2-3.5MCS/MTSRVN41821-CD2-3.5XTS3000/SABER PORTABLE YES RKN4046KHVN9085 3.51-20 R NO HLN9359 PROG. STAND RVN4057 3.532 X 8 CODEPLUG NO3080385B23 & 5880385B30 MDVN4965 3.59100-WS/T CONFIG KITRVN4053 3.5ASTRO DIGITAL INTERFACE NO3080385B23RVN41842-CD RKN4046A (Portable) 2-3.5ASTRO PORTABLE /MOBILE YES3080369B73 or0180300B10 (Mobile) RVN41831-CD3080369B732-3.5ASTRO SPECTRA MOBILE YES(Low / Mid Power)0180300B10 (High Power) RVN4185CD ASTRO SPECTRA PLUS MOBILE NO MANY OPTIONS; SEESERVICE BRIEF#SB-MO-0101RVN4186CD ASTRO SPECTRA PLUS MANY OPTIONS;MOBILE/PORTABLE COMB SEE SERVICE BRIEF#SB-MO-0101RVN4154 3.5ASTROTAC 3000 COMPAR.3080385B23RVN5003 3.5ASTROTAC COMPARATORS NO3080399E31 Adpt.5880385B34RVN4083 3.5BSC II NO FKN5836ARVN4171 3.5C200RVN4029 3.5CENTRACOM SERIES II NO VARIOUS-SEE MANUAL6881121E49RVN4112 3.5COMMAND PLUS NORVN4149 3.5COMTEGRA YES3082056X02HVN6053CD CT250, 450, 450LS YES AAPMKN4004RVN4079 3.5DESKTRAC CONVENTIONAL YES3080070N01RVN4093 3.5DESKTRAC TRUNKED YES3080070N01RVN4091 3.5DGT 9000 DESKSET YES0180358A22RVN4114 3.5GLOBAL POSITIONING SYS.NO RKN4021AHVN8177 3.5GM/GR300/GR500/GR400M10/M120/130YES3080070N01RVN4159 3.5GP60 SERIES YES PMLN4074AHVN9128 3.5GP300 & GP350RVN4152 3.5GP350 AVSRVN4150 3.5GTX YES HKN9857 (Portable)3080070N01(Mobile) HVN9025CD HT CDM/MTX/EX SERIES YES AARKN4083/AARKN4081RiblessAARKN4075RIBLESS NON-USA RKN4074RVN4098H 3.5HT1000/JT1000-VISAR YES3080371E46(VISAR CONV)RVN4151 3.5HT1000 AVSRVN4098 3.5HT1000/ VISAR CONV’L.YES RKN4035B (HT1000) HVN9084 3.5i750YES HLN-9102ARVN4156 3.5LCS/LTS 2000YES HKN9857(Portable)3080070N01(Mobile) RVN4087 3.5LORAN C LOC. RECV’R.NO RKN4021ARVN4135 3.5M100/M200,M110,M400,R100 includesHVN9173,9177,9646,9774YES3080070N01RVN4023 3.5MARATRAC YES3080070N01RVN4019 3.5MAXTRAC CONVENTIONAL YES3080070N01RVN4139 3.5MAXTRAC LS YES3080070N01RVN4043 3.5MAXTRAC TRK DUPLEX YES3080070N01RVN4178CD MC SERIES, MC2000/2500DDN6124AW/DB25 CONNECTORDDN6367AW/DB9 CONNECTOR RVN41751-CD Rib to MIC connector 1-3.5MCS2000 RKN4062BRVN41131-3.5MCS2000RVN4011 3.5MCX1000YES3000056M01RVN4063 3.5MCX1000 MARINE YES3000056M01RVN4117 3.5MDC/RDLAP DEVICESRVN4105 3.5MOBILE PROG. TOOLRVN4119 3.5MOBITEX DEVICESRVN4128 3.5MPT1327-1200 SERIES YES SEE MANUALRVN4025 3.5MSF5000/PURC/ANALOG YES0180355A30RVN4077 3.5MSF5000/10000FLD YES0180355A30RVN4017K 3.5MT 1000YES RTK4205CRVN4148 3.5MTR 2000YES3082056X02RVN4140 3.5MTRI 2000NORVN41761-CD MTS2000, MT2000*, MTX8000, MTX90001-3.5*programmed by DOS which is included in the RVN4176RVN4131 3.5MTVA CODE PLUG FIXRVN4142 3.5MTVA DOCTOR YES3080070N01RVN4131 3.5MTVA3.EXERVN4013 3.5MTX800 & MTX800S YES RTK4205CRVN4097 1-CD MTX8000/MTX9000,MTS2000,MT2000*,* programmed by DOS which is included in the RVN4176HVN9067CD MTX850/MTX8250MTX950,MTX925RVN4138 3.5MTX-LS YES RKN4035DRVN4035 3.5MX 1000YES RTK4203CRVN4073 3.5MX 800YES RKN4006BHVN9395 P100, P200 LB, P50+, P210, P500, PR3000RVN4134 3.5P100 (HVN9175)P200 LB (HVN9794)P50+ (HVN9395)P210 (HVN9763)P500 (HVN9941)PR3000 (HVN9586)YES RTK4205HVN9852 3.5P110YES HKN9755A/REX1143 HVN9262 3.5P200 UHF/VHF YES RTK4205RVN4129 3.5PDT220YVN4051 3.5PORTABLE REPEATER Portable rptr.P1820/P1821AXRVN4061C 3.5PP 1000/500NO3080385B23 & 5880385B30 RVN5002 3.5QUANTAR/QUANTRO NO3O80369E31RVN4135 3.5R100 (HVN9177)M100/M200/M110/M400YES0180358A52RVN4146 3.5RPM500/660RVN4002 3.5SABER YES RTK4203CRVN4131 3.5SETTLET.EXEHVN9007 3.5SM50 & SM120YESRVN4039 3.5SMART STATUS YES FKN5825AHVN9054 3.5SOFTWARE R03.2 P1225YES3080070N01HVN9001 3.5SOFTWARE R05.00.00 1225LS YES HLN9359AHVN9012 3.5SP50RVN4001N 3.5SPECTRA YES3080369B73 (STANDARD)0180300B10 (HIGH POWER) RVN4099 3.5SPECTRA RAILROAD YES3080369B73RVN4110 3.5STATION ACCESS MODULE NO3080369E31RVN4089A 3.5STX TRANSIT YES0180357A54RVN4051 3.5SYSTEMS SABER YES RTK4203BRVN4075 3.5T5600/T5620 SERIES NO3080385B23HVN9060CD TC3000, TS3000, TR3000RVN4123 3.5VISAR PRIVACY PLUS YES3080371E46FVN4333 3.5VRM 100 TOOLBOX FKN4486A CABLE &ADAPTORRVN4133 3.5VRM 500/600/650/850NORVN4181CD XTS 2500/5000 PORTABLES RKN4105A/RKN4106A RVN41002- 3.5XTS3000 ASTRO PORTABLE/MOBILERVN4170 3.5XTS3500YES RKN4035DRIB SET UPRLN4008E RADIO INTERFACE BOX (RIB)0180357A57RIB AC POWER PACK 120V0180358A56RIB AC POWER PACK 220V3080369B71IBM TO RIB CABLE (25 PIN) (USE WITH XT & PS2)3080369B72IBM TO RIB CABLE (9 PIN)RLN443825 PIN (F) TO 9 PIN (M) ADAPTOR (USE W/3080369B72 FOR AT APPLICATION) 5880385B308 PIN MODULAR TO 25 PIN ”D” ADAPTOR (FOR T5600 ONLY)0180359A29DUPLEX ADAPTOR (MOSTAR/TRAXAR TRNK’D ONLY)Item Disk Radio RIB Cable Number Size Product Required Number Item Disk Radio RIB Cable Number Size Product Required NumberUtilizing your personal computer, Radio Service Software (RSS)/Customer Programming Software (CPS)/CustomerConfiguration Software (CCS) enables you to add or reprogram features/parameters as your requirements change. RSS/CPS/CCS is compatible with IBM XT, AT, PS/2 models 30, 50, 60 and 80.Requires 640K RAM. DOS 3.1 or later. Consult the RSS users guide for the computer configuration and DOS requirements. (ForHT1000, MT/MTS2000, MTX838/8000/9000, Visar and some newer products —IBM model 386, 4 MEG RAM and DOS 5.0 or higher are recommended.) A Radio Interface Box (RIB) may be required as well as the appropriate cables. The RIB and cables must be ordered separately.Licensing:A license is required before a software (RVN) order is placed. The software license is site specific (customer number and ultimate destination tag). All sites/locations must purchase their own software.Be sure to place subsequent orders using the original customer number and ship-to-tag or other licensed sites; ordering software without a licensed customer number and ultimate tag may result in unnecessary delays. To obtain a no charge license agreement kit, order RPX4719. To place an order in the U.S. call 1-800-422-4210. Outside the U.S., FAX 847-576-3023.Subscription Program:The purchase of Radio ServiceSoftware/Customer Programming/Customer ConfigurationSoftware (RVN & HVN kits) entitles the buyer/subscriber to three years of free upgrades. At the end of these three years, the sub-scriber must purchase the same Radio Service Software kit to receive an additional three years of free upgrades. If the sub-scriber does not elect to purchase the same Radio Service Software kit, no upgrades will be sent. Annually a subscription status report is mailed to inform subscribers of the RSS/CPS/CCS items on our database and their expiration dates.Notes:1)A subscription service is offered on “RVN”-Radio Service Software/Customer Programming/Customer Configuration Software kits only.2)“RVN” software must only be procured through Radio Products and Services Division (RPSD). Software not procured through the RPSD will not be recorded on the subscription database; upgrades will not be mailed.3)Upgrades are mailed to the original buyer (customer number & ultimate tag).4)SP software is available through the radio product groups.The Motorola General Radio Service Software Agreement is now available on Motorola Online. If you need assistance please feel free to submit a “Contact Us” or call 800-422-4210.SMART RIB SET UPRLN1015D SMART RIB0180302E27 AC POWER PACK 120V 2580373E86 AC POWER PACK 220V3080390B49SMARTRIB CABLE (9 PIN (F) TO 9 PIN (M) (USE WITH AT)3080390B48SMARTRIB CABLE (25 PIN (F) TO 9 PIN (M) (USE WITH XT)RLN4488ASMART RIB BATTERY PACKWIRELESS DATA GROUP PRODUTS SOFTWARERVN4126 3.59100-386/9100T DEVICES MDVN4965 3.59100-WS/T CONFIG’TN RVN41173.5MDC/RDLAP DEVICESPAGING PRODUCTS MANUALS6881011B54 3.5ADVISOR6881029B90 3.5ADVISOR ELITE 6881023B20 3.5ADVISOR GOLD 6881020B35 3.5ADVISOR PRO FLX 6881032B30 3.5BR8506881032B30 3.5LS3506881032B30 3.5LS5506881032B30 3.5LS7506881033B10 3.5LS9506881035B20 3.5MINITOR III8262947A15 3.5PAGEWRITER 20008262947A15 3.5PAGEWRITER 2000X 6881028B10 3.5TALKABOUT T3406881029B35 3.5TIMEPORT P7308262947A15 3.5TIMEPORT P930NLN3548BUNIVERSAL INTERFACE KITItem Disk Radio NumberSize Product。

台湾群创液晶显示屏,参数

0.066(W) X 0.198(H) 0.0529(W)X0.1587(H) 0.077(W)X0.231(H) 50/70/70/70 6 O'Clock 50% 500 500 25 58 40pin FPC, Parallel 24bit RGB -20~70 -30~80 60℃,90% RH MP 50/70/70/70 6 O'Clock 50% 250 500 25 TBD 50pin FPC, Parallel 24bit RGB -20~70 -30~80 40℃,90% RH WS 50/70/70/70 6 O'Clock 50% X 500 25 25 40pin FPC, Parallel 24bit RGB -20~70 -30~80 60℃,90% RH MP
Prepared :MDBU/MKT Update:2013/03/13 Size & Model Name Item Product type Screen Size Aspect Ratio Display Mode Resolution PPI ( Pixel per inch ) Module/Panel Size(mm) Active Area(mm) Dot Pitch(mm) Viewing Angle (Tpy.)θT/ θB/θL/θR Viewing direction NTSC Luminance(nits) Contrast Ratio Response Time(ms) Weight (g) Interface Operation Temperature( ℃ ) Storage Temperature (℃ ) HTHH.(op) Status AT043TN24 V.7 Module+T/P 4.3" 16:9 Transmissive 480X3(RGB)X272 128 105.5 x 67.2 x 4.05 95.04 x 53.856 0.066(W) X 0.198(H) 50/70/70/70 6 O'Clock 50% 400 500 25 58 40pin FPC, Parallel 24bit RGB -20~70 -30~80 60℃,90% RH MP 4.3"D AT043TN25 V.2 Module 4.3" 16:9 Transmissive 480X3(RGB)X272 128 105.5 x 67.2 x 2.9 95.04 x 53.856 5"DN TBD Module 5.0'' 4:3 Transmissive 640X3(RGB)X480 160 117.65 x 88.43 x 5.7 101.568 x 76.176 5.0"DW AT050TN30 FOG 5.0'' 16:9 Transmissive 480X3(RGB)X272 110 117.70 × 72.80 × 1.43 110.88 x 62.832 HE050NA-01F FOG 5.0'' 15:9 Transmissive 800X3(RGB)X480 188 115.6 × 74.38 × 1.43 108 x 64.8 0.045(W) x 0.135(H) 50/70/70/70 6 O'Clock 50% / 500 25 26 50pin FPC, Parallel 24bit RGB -20~70 -30~80 60℃,90% RH MP 5"DH EJ050NA-01G Module 5.0" 15:9 Transmissive 800X3(RGB)X480 188 120.7 x 76.3x 3.1 108 x 64.8 0.045(W) x 0.135(H) 50/70/70/70 6 O'Clock 50% 350 500 25 60 50pin FPC, Parallel 24bit RGB -20~70 -30~80 60℃,90% RH MP AT056TN53 V.1 Module 5.6'' 4:3 Transmissive 640X3(RGB)X480 144 126.5 x 100.0 x 5.7 112.896 x 84.672 0.0588(W) x 0.1764(H) 50/70/70/70 6 O'Clock 50% 350 500 25 83 40pin FPC, Parallel 18bit RGB -20~70 -30~80 40℃,90% RH MP 5.6"D AT056TN52 V.3 Module 5.6'' 4:3 Transmissive 640X3(RGB)X480 144 126.5 x 100.0 x 5.7 112.896 x 84.672 0.0588(W) x 0.1764(H) 50/70/70/70 6 O'Clock 50% 200 500 25 127.5 50pin FPC, Parallel 24bit RGB -20~70 -30~80 40℃,90% RH MP ZE065NA-01B FOG 6.5" 16:9 Transmissive 800X3(RGB)X480 150 152.10 × 86.60 × 1.43 143.40 × 76.70 0.060(W) × 0.160 (H) 50/70/70/70 6 o’clock 50% NA 500 25 TBD 50pin FPC, Parallel 24bit RGB -20~60 -30~70 40℃,90% RH WS 6.57 V.D Module 7" 16:9 Transmissive 480X3(RGB)X234 74 164.9 x 100.0 x 5.7 154.08 x 86.58 0.107(W) X 0.370(H) 40/60/60/60 6 O'Clock 50% 200 300 35 166 Analog(26 Pin FPC) -30~85 -30~85 60℃,90% RH MP AT070TN83 V.1 Module 7" 15:9 Transmissive 800X3(RGB)X480 133 165 x 104 x 4.4 152.4 x 91.44

液晶AV驱动板规格书-AdafruitIndustries

液晶驱动板规格书产品名称 PCB-800099驱动板文件编号 TYT20120909供应商：深圳市天宇朗通科技有限公司地址：深圳福田区振华路高科德电子市场42073联系人张先生客户名称：客户地址：联系人文件级别公共文件发布日期2012-09-091.产品说明：本驱动板可以1，1路VGA信号输入2，2路A V信号输入3，1路HDMI信号输入,且本IC支持的是HDMI1.14，1路倒车信号输入5，支持宽电压输入，并可以在，5V-24V之间正常工作，6，标准背光6PIN，接口，可外接高压板7，驱动板集成液晶屏LED背光驱动板路，8，标准LVDS信号输出，可支持单6，单8，双6，双8等标准的LVDS信号的液晶屏,但只支持屏供电为3.3V的液晶屏9，标准按键板接口，并支持双色LED指示灯显示10，支持TTL信号输出，可支持AT070TN92,AT065TN14AT080TN52AT090TN12AT090TN10AT070TN90AT070TN93AT070TN94等，通用50PIN接口的TTL液晶屏11，配合本公司编号为PCB800100的液晶屏转接板，可支持如下液晶屏EJ070NA01-1024X600分辨率EJ080NA04B-1024X768分辨率ZJ070NA01,型号的通用40PIN高分液晶屏12,配合PCB800100,还可以支持4。

3，5，6，7寸，40PIN通用的屏，定义参见AT0543TN24V,113,本驱动板最大输出显示分辨率为，1920X1080超过,1440X900显示分辨率时，需要视IC的工作情况，增加散热片，以降低IC的工作温度）14本IC，VGA部分可以直接输入YPBPR信号，通过程序实现15，本驱动板可增加遥控功能（需要通过软件实现）16，本驱动板可以自动检测，并显示相关的输入电压信息-----注，此功能为定制功能，需要联系我公司技术部17，本驱动板可以支持自动检测信号开关机功能，--此功能为定制功能18，本驱动板可以加BNC接口---需要定制19，支持倒车控制，并显示A V2上，倒车电压支持50V以内的电压输入20，本驱动板定位孔为四个，21，如果特殊要求，我公司可以提供其它的定制服务22，客户需要改程序，需要连接我公司，购买相关的程序下载板，23，利用本公司的USB接口程序下载板，可以自行在BIN代码上添加LOGO6产品尺寸图7接口功能详细说明7.1CON1,接口定义8 运输，存储，使用要求1，不要重压和弯折变形 2，防静电和水3，相对湿度，小于80% 4, 使用温度 -1-度--+60度 5，使用湿度0-+40度。

Innolux-群创 CONNECTOR

连接器P/N
107C51-0000RA-G4 107C51-0000RA-G4 093G30-B0001A 093G30-B2001A 093G30-B0001A FI-R51S-HF MSAKT2407P30HA 093G30-B0001A
FH23-39S-0.3SHW (05)
液晶屏P/N
M260J1-L01 M240J1-L03 M240J1-L02 M240J1-L01 M236H5-L0A M236H5-L02 M236H5-L01 M236H3-LA2 M236H3-L02 M236H3-L01 M236H1-L08 M236H1-L07 M236H1-L01 M220Z3-LA1 M220Z3-L07 M220Z3-L03 M220Z1-L09 M220Z1-L08 M220Z1-L07 M220Z1-L06 M220Z1-L05 M220Z1-L03 M220Z1-L02 M220Z1-L01 M220J1-L01 M216H5-L01 M216H1-L07 M216H1-L05 M216H1-L03 M216H1-L02 M216H1-L01 M215H3-LA1 M215H3-L01 M215H1-L03 M215H1-L02 M215H1-L01 M201U1-L01 M201P1-L03 M201P1-L01 M200O3-LA1 M200O3-L01 M200O1-L05 M200O1-L03 M200O1-L02 M200O1-L01 M190Z1-P01 M190Z1-L03 M190Z1-L01 M190E6-L01 M190E5-L0G M190E5-L0E M190E5-L0B M190E5-L0A M190E3-L02 M190E3-L01 M190E2-L01 M190A1-L10 M190A1-L0G M190A1-L0F M190A1-L0C M190A1-L0B M190A1-L0A M190A1-L09 M190A1-L08 M190A1-L07 M190A1-L06 M190A1-L05 M190A1-L03 M190A1-L02 M190A1-L01

BITEK BIT1628B v2.00 原理图

Title Size Document Number Date:The circuits shown are intended to explain applications of the products concerned.BiTEK is not responsible for any infringement of third party or any other intellectual property rights that may arise from the use of these circuits.01. POWERTuesday, April 08, 2014Title Size Document Number Date:The circuits shown are intended to explain applications of the products concerned.BiTEK is not responsible for any infringement of third party or any other intellectual property rights that may arise from the use of these circuits.02. BIT1628A/BTuesday, April 08, 2014BIT1628A/B_LQFP64Title Size Document Number Date:The circuits shown are intended to explain applications of the products concerned.BiTEK is not responsible for any infringement of third party or any other intellectual property rights that may arise from the use of these circuits.03. LED_BLACKLIGHT A Tuesday, April 08, 2014Title Size Document Number Date:The circuits shown are intended to explain applications of the products concerned.BiTEK is not responsible for any infringement of third party or any other intellectual property rights that may arise from the use of these circuits.04. OUTPUTTuesday, April 08, 2014Title Size Document Number Date:The circuits shown are intended to explain applications of the products concerned.BiTEK is not responsible for any infringement of third party or any other intellectual property rights that may arise from the use of these circuits.05. DESIGN HISTORY A Tuesday, April 08, 2014。

LMT070DICFWD-NAA-Manual-Rev0.2

LMT070DICFWD-NAA
LCD Module User Manual
Prepared by: K.C.
Date: 2010-11-18
Checked by: Date:
Approved by: Date:
Rev. Descriptions 0.1 Preliminary release 0.2 Update Jumper Setting
Vertical Sync Input
Pull Hi
Horizontal Sync Input
Data Clock Input
Data shall be latched at the falling edge of DCLK.
Touch Screen X- terminal
Touch Screen X+ terminal
VCC
3
B0
:
:
10
B7
11
GND
12
G0
:
:
19
G7
20
GND
21
R0
:
:
28
R7
29
GND
30
LED_ADJ
31
NC
32
NC
33
DE
34
VS
35
HS
I/O
Power
Input
Power
Input
Power
Input
Power Input --Input Input Input
36
DCLK
Input
Digital 18-bits RGB a-Si TFT active matrix Transmissive / Normal White 7.0” 190.0 x 112.0 x 12.2 (mm) (see attached drawing for details) 154.08 x 85.92 (mm) 800 x 3 (RGB) x 480 0.0642 x 0.179 (mm) RGB Stripe LED Anti-Glare Treatment 6 o’clock 4wire resistive -20 ~ +70°C -30 ~ +80°C

日本白光HAKKO主机型号大全

锡线 HEXSOL FS301-01 FS302-01 FS302-02 FS302-03 FS302-04 FS303-01 FS303-02
锡线 HEXSOL FS300-01 FS400-01 FS400-02 FS401-01 FS401-02
锡线 HEXSOL FS402-01 FS402-02 FS402-03 FS402-04
化学助焊膏 PASTE(FS-120) FS120-01 FS120-02
助焊剂 001 001-01 001-02 001-03 001-04
助焊剂 CHEMICAL 1
助焊剂 SUSSOL-F 89-031 89-100 89-400 89
锡线 HEXSOL FS500-01 FS501-01 FS501-02 FS501-03 FS600-01 FS600-02 FS600-03 FS600-04
化学膏 FS-100 FS-100
焊咀清洁器 FT-700 FT700-01
电热剥线钳 FT-801 FT801-01
切割机电动装备 152B 152B
电阻切割成形机 153 153-1
电阻切割成形机 154 154-1
电阻切割机 155 155-1 155-2
精钢电子工具剪钳 106-01~08 106-01 106-02 106-03 106-04 106-05 106-06 106-07 106-08
自动出锡焊铁 958 958-01 958-02
自动出锡焊铁 959 959-01 959-02
电烙铁 FX-600 FX600-01 FX600-02
电烙铁 FX-601 FX601-01 FX601-03
定温烙铁 DASH N452 N453 N454 N452E N453E N454E

10.1寸液晶屏选型指导

7 800*480
-20 70 250
7 800*480
0 50 250
10.4 800*600
-20 70 400
10.4 1024*768 -30 70 500
10.4 640*480
-20 70 350
10.1 1024*600 -20 70
10.1 1024*600 -20 80 450
10.1 2560*1600
平板平板平板平板车用车用
平板平板平板平板平板工业工业工业工业工业工业工业工业工业工业
EINK元太
工业
天马
平板
原装原装原装原装原装原装原装原装原装原装原装原装原装原装原装原装原装原装组装组装组装组装
HSD101PXN1-B HSD101PWW3-B HSD101PWW1-H HSD101PWW1-G HSD101PFW5-C/-00 HSD101PWW1-H HSD100IFW1-A00
-20
原装 AM-1280800N1TZQW-00H 10.1 1280*800 -20
原装 BP101WX1-400
10.1 1280*800 -20
原装 BP101WX1-300
10.1 1280*800 -20
原装
AT101WSM-NW03800(3900)
10.1 1024*600 -20
原装 HV070WS1-105
0
10.1
FG1001L0DSSWMG01
10.1 1280*800 -20
原装 AM-1024600L2TMQW-00H 10.1 1024*600 -20
原装 AM-1024600L3TMQW-00H 10.1 1024*600 -20

AT070TN94

INNO L U X DISPLAY CORPORATIONLCD MODULESPECIFICATIONCustomer: Model Name: AT070TN94SPEC NO.: A070-94-TT-01 Date: 2009/07/07 Version:01ϮPreliminary Specification ϭFinal SpecificationFor Customer ’s AcceptanceApproved byCommentApproved byReviewed byPrepared byJoe Lin2009/07/07James Yu2009/07/07David Lee2009/07/07InnoLux copyright 2004All rights reserved,Copying forbidden.Record of RevisionVersion Revise Date Page ContentPre-Spec.01 2009/07/07 Initial ReleaseI NNO L U XContents1. General Specifications (1)2. Pin Assignment (2)3. Operation Specifications (5)3.1. Absolute Maximum Rating (5)3.1.1. Typical Operation Conditions (6)3.1.2. Current Consumption (7)3.1.3. Backlight Driving Conditions (7)3.2. Power Sequence (8)3.3. Timing Characteristics (9)3.3.1. AC Electrical Characteristics (9)3.3.2. Data Input Format (10)3.3.3. Timing (11)4. Optical Specifications (12)5. Reliability Test Items (16)6. General Precautions (17)6.1. Safety (17)6.2. Handling (17)6.3. Static Electricity (17)6.4. Storage (17)6.5. Cleaning (17)7. Mechanical Drawing (18)8. Package Drawing (19)8.1 Packaging Material Table (19)8.2 Packaging Quantity (19)8.3 Packaging Drawing (20)1. General SpecificationsNo. Item Specification Remark1 LCD size 7.0 inch(Diagonal)2 Driver element a-Si TFT active matrix3 Resolution 800 × 3(RGB) × 4804 Display mode Normally White, Transmissive5 Dot pitch 0.0642(W) × 0.1790(H) mm6 Active area 154.08(W) × 85.92(H) mm7 Module size 164.9(W) ×100.0(H) ×5.7(D) mm Note 18 Surface treatment Anti-Glare9 Color arrangement RGB-stripe10 Interface Digital11 Backlight power consumption 1.674W (Typ.)12 Panel power consumption 0.226W (Typ.)13 Weight (150g) (Typ.)Note 1: Refer to Mechanical Drawing.2. Pin AssignmentTFT LCD Panel Driving SectionFPC Connector is used for the module electronics interface. The recommended model is FH12A-50S-0.5SH manufactured by Hirose.Pin No. Symbol I/O Function Remark1 V LED+P Power for LED backlight (Anode)2 V LED+P Power for LED backlight (Anode)3 V LED-P Power for LED backlight (Cathode)4 V LED-P Power for LED backlight (Cathode)5 GND P Power ground6 V COM I Common voltage7 DV DD P Power for Digital Circuit8 MODE I DE/SYNC mode select Note 19 DE I Data Input Enable10 VS I Vertical Sync Input11 HS I Horizontal Sync Input12 B7 I Blue data(MSB)13 B6 I Blue data14 B5 I Blue data15 B4 I Blue data16 B3 I Blue data17 B2 I Blue data18 B1 I Blue data Note 219 B0 I Blue data(LSB) Note 220 G7 I Green data(MSB)21 G6 I Green data22 G5 I Green data23 G4 I Green data24 G3 I Green data26 G1 I Green data Note 227 G0 I Green data(LSB) Note 228 R7 I Red data(MSB)29 R6 I Red data30 R5 I Red data31 R4 I Red data32 R3 I Red data33 R2 I Red data34 R1 I Red data Note 235 R0 I Red data(LSB) Note 236 GND P Power Ground37 DCLK I Sample clock Note 338 GND P Power Ground39 L/R I Left / right selection Note 4,540 U/D I Up/down selection Note 4,541 V GH P Gate ON Voltage42 V GL P Gate OFF Voltage43 AV DD P Power for Analog Circuit44 RESET I Global reset pin. Note 645 NC - No connection46 V COM I Common Voltage47 DITHB I Dithering function Note 748 GND P Power Ground49 NC - No connection50 NC - No connectionI: input, O: output, P: PowerNote 1: DE/SYNC mode select. Normally pull high.When select DE mode, MODE=”1”, VS and HS must pull high.When select SYNC mode,MODE= ”0”, DE must be grounded.Note 2: When input 18 bits RGB data, the two low bits of R,G and B data must be grounded.Note 3:Data shall be latched at the falling edge of DCLK.Note 4: Selection of scanning modeSetting of scan control inputU/D L/RScanning directionGND DV DD Up to down, left to rightDV DD GND Down to up, right to leftGND GND Up to down, right to leftDV DD DV DD Down to up, left to rightNote 5: Definition of scanning direction.Refer to the figure as below:Note 6: Global reset pin. Active low to enter reset state. Suggest to connect with an RC reset circuit for stability. Normally pull high.Note 7: Dithering function enable control, normally pull high.When DITHB=”1”,Disable internal dithering function,When DITHB=”0”,Enable internal dithering function,RightLeftDownUp3. Operation Specifications3.1. Absolute Maximum Ratings(Note 1)ValuesItem SymbolMin. Max.Unit RemarkDV DD -0.3 5.0 VAV DD 6.5 13.5 VV GH -0.3 40.0 VV GL -20.0 0.3 V Power voltageV GH-V GL- 40.0 V Operation Temperature T OP -30 85 ℃Storage Temperature T ST-30 85 ℃LED Reverse Voltage V R- 1.2 VEach LEDNote 2 LED Forward Current I F- 25 mA Each LEDNote 1: The absolute maximum rating values of this product are not allowed to be exceeded at any times. Should a module be used with any of the absolute maximum ratingsexceeded, the characteristics of the module may not be recovered, or in an extremecase, the module may be permanently destroyed.Note 2: V R Conditions: Zener Diode 20mA3.1.1. Typical Operation Conditions( Note 1)ValuesUnit Remark Item SymbolMin. Typ. Max.DV DD 3.0 3.3 3.6 V Note 2AV DD 10.2 10.4 10.6 VPower voltageV GH 15.3 16.0 16.7 VV GL -7.7 -7.0 -6.3 VInput signal voltage V COM 3.8 4.0 4.2 VInput logic high voltage V IH 0.7 DV DD - DV DD VNote 3 Input logic low voltage V IL 0 - 0.3 DV DD VNote 1: Be sure to apply DV DD and V GL to the LCD first, and then apply V GH.Note 2: DV DD setting should match the signals output voltage (refer to Note 3) of customer’s system board.Note 3: DCLK,HS,VS,RESET,U/D, L/R,DE,R0~R7,G0~G7,B0~B7,MODE,DITHB.3.1.2. Current ConsumptionValuesItem SymbolMin. Typ. Max.Unit RemarkI GH - 0.2 1.0 mA V GH =16.0VI GL - 0.2 1.0 mA V GL = -7.0V IDV DD - 4.0 10 mA DV DD =3.3VCurrent for DriverIAV DD - 20 50 mA AV DD =10.4V3.1.3. Backlight Driving ConditionsValuesItem SymbolMin. Typ. Max.Unit Remark Voltage for LED backlight V L 8.4 9.3 10.2 V Note 1 Current for LED backlight I L 170 180 200 mALED life time - 20,000 - - Hr Note 2Note 1: The LED Supply Voltage is defined by the number of LED at Ta=25℃ andI L =180mA.Note 2: The “LED life time” is defined as the module brightness decrease to 50% original brightness at Ta=25℃ and I L =180mA. The LED lifetime could be decreased ifoperating I L is lager than 180mA.3.2. Power Sequencea. Power on:Note: Data include R0~R7, B0~B7, GO~G7, U/D, L/R, DCLK, HS,VS,DE.DV DD→VGL→VGH→Data→B/LB/L→Data→VGH→VGL→DV DD3.3. Timing Characteristics3.3.1. AC Electrical CharacteristicsValuesItem SymbolMin. Typ. Max.Unit Remark HS setup time T hst8 - - nsHS hold time T hhd 8 - - nsVS setup time T vst8 - - nsVS hold time T vhd8 - - nsData setup time T dsu8 - - nsData hole time T dhd8 - - nsDE setup time T esu 8 - - nsDE hole time T ehd8 - - nsDV DD Power On Slew rate T POR - - 20 ms From 0 to 90% DV DDRESET pulse width T Rst 1 - - ms DCLK cycle time T coh 20 - - ns DCLK pulse duty T cwh 40 50 60 %3.3.2. Data Input Format3.3.3. TimingValuesUnit Remark Item SymbolMin. Typ. Max.Horizontal Display Area thd- 800 - DCLKDCLK Frequency fclk26.4 33.3 46.8 MHzOne Horizontal Line th862 1056 1200 DCLKHS pulse width thpw 1 - 40 DCLKHS Blanking thb46 46 46 DCLKHS Front Porch thfp 16 210 354 DCLKValuesItem SymbolUnit RemarkMin. Typ. Max.Vertical Display Area tvd- 480 - THVS period time tv 510 525 650 THVS pulse width tvpw 1 - 20 THVS Blanking tvb23 23 23 THVS Front Porch tvfp 7 22 147 TH4. Optical SpecificationsValuesItem Symbol ConditionMin. Typ. Max.Unit RemarkθL Φ=180°(9 o’clock) 60 70 -θRΦ=0°(3 o’clock) 60 70 -θTΦ=90°(12 o’clock) 40 50 -Viewing angle(CR≥ 10)θBΦ=270°(6 o’clock) 60 70 -degree Note 1T ON - 10 20 msec Note 3 Response timeT OFF - 15 30 msec Note 3 Contrast ratio CR 400 500 - - Note 4W X 0.26 0.31 0.36 -Color chromaticityW Y 0.28 0.33 0.38 -Note 2Note 5Note 6 Luminance L 320 400 - cd/m² Note 6 LuminanceuniformityY UNormalθ=Φ=0°70 75 - % Note 7Test Conditions:1. DV DD=3.3V, I L=180mA (Backlight current), the ambient temperature is 25℃.2. The test systems refer to Note 2.Note 1: Definition of viewing angle rangeFig. 4-1 Definition of viewing angleNote 2: Definition of optical measurement system.The optical characteristics should be measured in dark room. After 30 minutesoperation, the optical properties are measured at the center point of the LCD screen. (Response time is measured by Photo detector TOPCON BM-7, other items are measured by BM-5A/Field of view: 1° /Height: 500mm.)Fig. 4-2 Optical measurement system setupNormal line θ=Φ=0°Photo detectorΦ=90°12 o’clock directionΦ=270°6 o’clock directionΦ=0°Φ=180°Active Area500mmLCMNormal line θ=Φ=0°Φ=90°12 o’clock directionΦ=270°6 o’clock direction Φ=0°Φ=180°Active AreaθLθTθBθRLCMNote 3: Definition of Response timeThe response time is defined as the LCD optical switching time interval between“White” state and “Black” state. Rise time (T ON) is the time between photo detector output intensity changed from 90% to 10%. And fall time (T OFF) is the timebetween photo detector output intensity changed from 10% to 90%.Fig. 4-3 Definition of response timeNote 4: Definition of contrast ratiostateBlack""theonLCDwhenmeasuredLuminancestateWhite""theonLCDwhenmeasuredLuminance(CR)ratioContrast=Note 5: Definition of color chromaticity (CIE1931)Color coordinates measured at center point of LCD.Note 6: All input terminals LCD panel must be ground while measuring the center area of the panel.The LED driving condition is I L=180mA .90%10%0%Photodetectoroutput(Relativevalue)ONTWhite (TFT OFF) Black (TFT ON) White (TFT OFF)Note 7:Definition of Luminance UniformityActive area is divided into 9 measuring areas (Refer to Fig. 4-4 ).Every measuring point is placed at the center of each measuring area.maxminBB(Yu)UniformityLuminance=L-------Active area length W----- Active area widthWW/3W/3W/6L/3L/3L/6LFig. 4-4 Definition of measuring pointsB max: The measured maximum luminance of all measurement position.B min: The measured minimum luminance of all measurement position.5. Reliability Test Items(Note3)Item Test Conditions Remark High Temperature Storage Ta = 85℃240hrs Note 1，Note 4 Low Temperature Storage Ta = -30℃240hrs Note 1，Note 4 High Temperature Operation Ts = 85℃240hrs Note 2，Note 4 Low Temperature Operation Ta = -30℃240hrs Note 1，Note 4 Operate at High Temperatureand Humidity+60℃, 90%RH 240hrs Note 4Thermal Shock -30℃/30 min ~ +85℃/30 min for a total 100cycles, Start with cold temperature and endwith high temperature.Note 4Vibration Test Frequency range:10~55Hz Stroke:1.5mmSweep:10Hz~55Hz~10Hz2 hours for each direction of X. Y. Z.(6 hours for total)Mechanical Shock 100G 6ms,±X, ±Y, ±Z 3 times for each directionPackage Vibration Test Random Vibration :0.015G*G/Hz from 5-200HZ, -6dB/Octave from 200-500HZ2 hours for each direction of X. Y. Z.(6 hours for total)Package Drop Test Height:60 cm1 corner, 3 edges, 6 surfacesElectro Static Discharge ± 2KV, Human Body Mode, 100pF/1500ΩNote 1: Ta is the ambient temperature of samples.Note 2: Ts is the temperature of panel’s surface.Note 3: In the standard condition, there shall be no practical problem that may affect the display function. After the reliability test, the product only guarantees operation,but don’t guarantee all of the cosmetic specification.Note 4: Before cosmetic and function test, the product must have enough recovery time, at least 2 hours at room temperature.6. General Precautions6.1. SafetyLiquid crystal is poisonous. Do not put it in your mouth. If liquid crystal touches your skin or clothes, wash it off immediately by using soap and water.6.2. Handling1. The LCD panel is plate glass. Do not subject the panel to mechanical shock or toexcessive force on its surface.2. The polarizer attached to the display is easily damaged. Please handle it carefullyto avoid scratch or other damages.3. To avoid contamination on the display surface, do not touch the module surfacewith bare hands.4. Keep a space so that the LCD panels do not touch other components.5. Put cover board such as acrylic board on the surface of LCD panel to protect panelfrom damages.6. Transparent electrodes may be disconnected if you use the LCD panel underenvironmental conditions where the condensation of dew occurs.7. Do not leave module in direct sunlight to avoid malfunction of the ICs.6.3. Static Electricity1. Be sure to ground module before turning on power or operating module.2. Do not apply voltage which exceeds the absolute maximum rating value.6.4. Storage1. Store the module in a dark room where must keep at 25±10℃ and 65%RH or less.2. Do not store the module in surroundings containing organic solvent or corrosivegas.3. Store the module in an anti-electrostatic container or bag.6.5. Cleaning1. Do not wipe the polarizer with dry cloth. It might cause scratch.2. Only use a soft sloth with IPA to wipe the polarizer, other chemicals mightpermanent damage to the polarizer.7. Mechanical Drawing8. Package Drawing8.1. Packaging Material TableNo. ItemModel(Material)Dimensions(mm)UnitWeight(kg)Quantity Remark1 LCMModuleAT070TN94 164.9 × 100.0 × 5.7 (0.150) 50pcs2 Partition BC Corrugatedpaper512 × 349 × 226 1.466 1set3 CorrugatedPaperB Corrugatedpaper510 × 350 0.071 4pcs4 CorrugatedBarB Corrugatedpaper512 × 11 × 3 0.046 4pcs5 Dust-ProofBagPE 700 × 530 0.048 1pcs6 A/S Bag PE 180 × 133 × 0.2 0.002 50pcs7 Carton Corrugatedpaper530 × 355 × 255 1.100 1pcs8 Total weight (10.682 kg± 5%)8.1 Packaging QuantityTotal LCM quantity in Carton: no. of Partition 2 Rows × quantity per Row 25 = 508.2 Packaging Drawing。

群创(INNOLUX)量产面板匹配连接器料号清单

P101KDZ-3Z2 P101KDA-AF0 P101KDA-AB0 P101KDA-AF4 P101LCA-3P1 P101KDZ-3Z1 ZJ101IA-17A ZJ101ZA-03B DJ103IA-03B G104X1-L04 G104X1-L03 G104S1-L01 G104V1-T03 G104AGE-L02 N116BGE-EA2 N116BGE-E32 N116BGE-EB2 N116BCA-EA1 N116BGE-E42 N116BGE-EB2 Rev.C3 N116HSG-WJ1 P120ZDG-BF1 G121X1-L04 G121X1-L03 G121AGE-L03 G121S1-L02 G121I1-L01 G121XCE-L0 G121XGE-L01 DJ123IA-01B JJ123IA-01E N125HCE-GN1 N125HCE-G61 G133IGE-L03 N133HCE-GP1 N133BGE-E31 N133BGE-EAB N133HCE-EN1 N133HCE-GA1
品牌
庆良广濑电机松下松下广濑电机广濑电机松下松下松下昆旺 DDK DDK 昆旺松下 I-PEX I-PEX I-PEX 广濑电机广濑电机 I-PEX 广濑电机广濑电机广濑电机广濑电机松下广濑电机广濑电机广濑电机 I-PEX 松下广濑电机 LS Mtron LS Mtron LS Mtron
LS Mtron I-PEX I-PEX 广濑电机昆旺昆旺 I-PEX 昆旺昆旺昆旺 I-PEX I-PEX I-PEX
昆旺 I-PEX 昆旺 I-PEX 广濑电机广濑电机信盛精工信盛精工广濑电机昆旺广濑电机 I-PEX 广濑电机昆旺广濑电机广濑电机昆旺松下昆旺 I-PEX I-PEX 广濑电机昆旺

安捷伦示波器探头选型指南1

1.5 m
10:1 500 MHz
1 MΩ, 6-15 pF
400 V CAT II
5000 系列 (500 MHz) 6000 (300 MHz-1 GHz)、 7000、5464x、54830 和 8000 系列
1.5 m
10:1 150 MHz
1 MΩ, 9-17 pF
400 V CAT II
单端有源探头特性
型号 N2795A N2796A 1157A 1158A
衰减 10:1 10:1 10:1 10:1
探头带宽 1 GHz 2 GHz 2.5 GHz 4 GHz
输入动态范围 0 至 ±8 V 0 至 ±8 V 0 至 ±2.5 V 0 至 ±2.5 V
应用和使用对数字系统和模拟系统设计执行通用、高速探测
10076B N2771B
电缆长度衰减典型探头带宽补偿示波器输入最大输入电压推荐示波器
1.5 m
1:1 20 MHz
高阻抗
400 V CAT II
1000、3000、2000 X、3000 X、5000、6000、 7000、8000、54600 系列
1.3 m
1:1 35 MHz
1 MΩ
衰减
要根据测试信号的幅度和示波器垂直灵敏度范围，选择探头的衰减比 (1:1、10:1、100:1、1000:1)。
带宽 (BW)
探头的额定带宽应与示波器相匹配，并保有对测试信号的裕量。但在较高频率时，地线电感和输入电容对系统性能的影响比探头带宽的影响更大。
最大输入电压 (Vmax)
为了确保用户安全，同时帮助用户保护示波器输入不会受到破坏性电压的影响及避免探头损坏，所选探头的额定电压必须高于被测信号。

A060SE02 V1 TFT Spec 091014_1

CUSTOMER APPROVAL SHEETCompany NameMODEL A060SE02 V1CUSTOMERAPPROVED□ APPROVAL FOR SPECIFICATIONS ONLY (Spec. Ver. 0.5)□ APPROVAL FOR SPECIFICATIONS AND ES SAMPLE (Spec. Ver. 0.5)□ APPROVAL FOR SPECIFICATIONS AND CS SAMPLE (Spec. Ver. 0.5)□ CUSTOMER REMARK :AUO PM : YW LiuP/N :Comment :1 Li-Hsin Rd. 2. Science-Based Industrial ParkHsinchu 300, Taiwan, R.O.C.Tel: +886-3-500-8899Fax: +886-3-577-2730Doc. version : 0.5Total pages : 24Date : 2009/10/14Product Specification6" EPD MODULE Model Name：A060SE02 V1 Planned Lifetime: From 2009/Jul. To2011/Jul. Phase-out Control: From 2011/Mar. To2011/Jul.EOL Schedule: 2011/Jul.< >Preliminary Specification◆< >Final SpecificationNote: The content of this specification is subject to change.© 2009 AU Optronics All Rights Reserved, Do Not Copy.Record of RevisionVersion Revise Date Page Content0.0 2009/05/04 All First Draft.7、9 Update VCOMDC、VCOMH、VCOML、VDPS、VDNS pin define16 Add VCOM relationship.0.1 2009/07/0617~18 Update power on/off sequence19 Update reflectance21 Update RA condition10 Add I/O pin sturcture0.2 2009/07/0919 Update Optical condition21 Update RA condition3 Update thickness4 Update module drawing0.3 2009/09/0410 Update power consumption17 Update optical performance19 Update RA condition0.4 2009/09/08 17 Update optical performance10 Update Power Consumption15 Update Power On/Off Characteristics0.5 2009/10/1418~19 Update RA conditions24 Update application CircuitContentsA.General Information (3)B.Outline Dimension (4)C.Electrical Specifications (5)1.Pin Assignment (5)2.Absolute Maximum Ratings (9)D.Electrical Characteristics (10)E.Input timing AC Characteristics (11)1. Horizontal input timing (11)1.1 Relation ship of input data and source output voltage (12)2. Vertical input timing (13)3. VCOM voltage definition (14)4. VCOM relationship (14)F.Power On/Off Characteristics (15)G.Optical Specification (16)H.Reliability Test Items (18)I.Packing and Marking (20)1. Packing Form (20)2. Module/Panel Label Information (21)3. Carton Label Information (21)J.Application Note (22)1. Application Circuit (22)A. General InformationThis product is for Electric Book application.NO. Item Unit Specification Remark1 Screen Size inch 6 (Diagonal)2 Display Resolution dot 800 (H)× 600(V)3 Overall Dimension mm 130.4(H) × 104.6(V) × 1.33(T) Note 14 Active Area mm 122.4(H)×90.6(V)5 Dot Pitch mm 0.153 (H)x 0.151(V)6 Gray level -- 167 Weight g (34.3)Note 1: Not include FPC but include sealant. Refer next page to get further information.ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PAPER SHALL NOT BE REPRODUCED, COPIED, OR TRANSFORMED TO ANY OTHER FORMSWITHOUT PERMISSION FROM AU OPTRONICS CORP.B. Outline DimensionC. Electrical Specifications1. Pin AssignmentRecommended connector : FH12-50S-0.5SH.Pin No. Symbol I/OI/OStructureDescription Remark1 Dummy -- -- Dummy pin2 VCOM O -- VCOM polarity output signal3 VCOM_BOT I -- VCOM signal setting pin4 VCOMDC P Type2 External voltage for VCOMDC power.5 VCOMH P -- External voltage for VCOM high power.6 VCOML P -- External voltage for VCOM low power.7 RST_N I Type 3 Global reset pin. Low reset.8 SHD_N I Type 3 DC-DC converter shut down pin. “0” : Enable.(Panel shut down;Default) “1” : Disable.9 PWR_RDY O Type 1 Power ready output.When SHD_N from “1” to “0”: PWR_RDY will become “0”.When SHD_N from “0” to “1”: after 100ms, PWR_RDY willbecome “1”.Note110 VCOMIN_0 I Type 2 Logic Input for VCOM voltage generate.11 VCOMIN_1 I Type 2 Logic Input for VCOM voltage generate.12 YOE I Type 3 Vertical output enable pin. Note213 YCLK I Type 3 Vertical clock. input Note214 UD I Type 3 Vertical (up/down) scan direction. U/D = "L": Shift up to down. Default U/D = "H": Shift down to up.15 YDIOD I/O Type 516 YDIOU I/O Type 5 Vertical start pulse input/output.These pins are used to input and output shift data. These pins are switched as input or output by setting the UD pin as follow.UD YDIOU YDIODL Output InputH Input Output17 XDIOL I/O Type 518 XDIOR I/O Type 5 Horizontal start pulse input/output.These pins are used to input and output shift data. These pins are switched as input or output by setting the SHL pin as follow.SHL XDIOL XDIORL Input OutputH Output Input19 LD I Type 3 Latch data.20 D0 I Type 3 Data input, First pixel LSB21 D1 I Type 3 Data input, First pixel MSB22 D2 I Type 3 Data input, Second pixel LSB23 D3 I Type 3 Data input, Second pixel MSB24 D4 I Type 3 Data input, Third pixel LSB25 D5 I Type 3 Data input, Third pixel MSB26 D6 I Type 3 Data input, Forth pixel LSB27 D7 I Type 3 Data input, Forth pixel MSB28 SHL I Type 3 Horizontal (left/right) scan direction. SHL = “L”: Shift right to left.SHL = “H”:Shift left to right. Default29 XCLK I Type 3 Horizontal Clock input.. Note330 VREF C -- For power setting capactor connected pin.31 VR P -- VCOMDC reference voltage32 AVDD C -- For power setting capactor connected pin.33 C1P C -- For charge pump capactor connected pin.34 C1N C -- For charge pump capactor connected pin.35 VSS P -- Digital ground36 VSSA P -- Analog ground.37 VDD P -- Analog power.38 VREF_POS C -- For power setting capactor connected pin.39 VREF_NEG C -- For power setting capactor connected pin.40 VDDX8 P -- DCDC positive voltage41 NVDDX8 P -- DCDC negative voltage42 VDD_DRV P -- DCDC power.43 ADRVU O Type 1 PWM output for DCDC converter.44 ADRVD O Type 1 PWM output for DCDC converter.45 VSS_DRV P -- DCDC ground.46 VDPS P -- External voltage for source postive power.47 VDNS P -- External voltage for source negative power.48 VDPG C -- For power setting capactor connected pin.49 VDNG C -- For power setting capactor connected pin.50 Dummy D -- Dummy pinI: Input pin; O:output pin, I/O: Input / Output; P: Power pin; C: capacitor pin; D：Dummy Note 1: Please reference chapter FNote 2: Please reference chapter ENote 3: Please reference chapter EI/O Pin Structure:2. Absolute Maximum RatingsItem Symbol Condition Min. Max. Unit Remark Power voltage VDD VSSA=VSS=0 -0.3 +5.0 VPower voltage VDD_DRV VSS_DRV=0 -0.3 +5.0 VVDPS VSSA=VSS=0 +20 V Source voltageVDNS VSSA=VSS=0 -20 VVDPG VSSA=VSS=0 -0.3 VDNG+40Gate voltageVDNG VSSA=VSS=0 VDPG-40 +0.3Storage temperature Tstg - -25 70 ℃Operating Topa - 0 50 ℃D. Electrical CharacteristicsItem Symbol Condition Min. Typical Max. UnitVDD VSSA=VSS=VSS_DRV=0V -- 3.3 -- V Supply VoltageVDD_DRV VSSA=VSS=VSS_DRV=0V -- 3.3 -- Low Level InputVoltageVil Digital input pins GND - 0.3xVDD V High Level InputVoltageVih Digital input pins 0.7xVDD - VDD V OperatingtemperatureT op- -- - °COperation Power Dissipation VDD=VDD_DRV=3.3VVDNS＝-15VVDPS＝15VVCOMH＝11.5V，VCOML＝-18.5V-- (21) (28) mAStandby Power Dissipation VDD=VDD_DRV=3.3VVDNS＝0VVDPS＝0VVCOMH＝0V，VCOML＝0V-- (0.2) (1) mAE. Input timing AC Characteristics1. Horizontal input timingFigure 1: LD input timingN=800Figure 2: Horizontal data Input timing(VDD=VDD_DRV=3.3V, VSSA=VSS=VSS_DRV=0V, TA=25℃)PARAMETER SYMBOL MIN. TYP. MAX. UNIT Clock pulse width T WXDCLK13 nsData setup time T setup 2 - - nsData hold time T hold 2 - - nsLD pulse width T WLD 1 - - XCLKTime from LD to XDIOL/XDIOR T LD_DIO 5 - - XCLK1.1 Relation ship of input data and source output voltageThe source driver output voltage will base on input 2 bits data, and the relationship is as below:MSB LSB Function0 0 Source output is 0V0 1 Source output is VDPS(+15V)1 0 Source output is VDNS(-15V)1 1 Source output is floating2. Vertical input timingYCLKYDIOU/YDIOD (Input)YDIOU/YDIOD (Output)YOEG1G212N3G3GNN=600Figure 3: Vertical input timing3. VCOM voltage definitionThe VCOM output voltage will base on input pins VCOMIN[1:0], and the relationship is as below:VCOMIN[1 :0] Function00 VCOM output is (-VDC) v01 VCOM output is (VDPS-VDC) v10 VCOM output is (VDNS-VDC) v11 VCOM output is floating4. VCOM relationshipVCOM will change while VOCMIN changeSource output will change while LD signal falling edge.F. Power On/Off Characteristics1. Recommended Power On/off SequenceThe suggested power on/off sequence is below:2. Power off sequence:G. Optical SpecificationAll optical specification is measured under typical condition (Note 1, 2)Item Symbol Condition Min. Typ. Max. Unit Remark Reflectance R white 30 33 -- %Note1,4Contrast RatioCRAt optimized viewing angle56--Note1, 5Response timeT r T f 30V 30V(300)(300)ms Note 3Note 1. Ambient temperature =25℃Note 2. Reflectance and constrast ratio are measured by KONICA MINOLTA spectrophotometerCM-2600d.Note 3. Definition of response time:The response time is defined as the time from image load to full updated display.The output signals of photo detector are measured when the input signals are changed from “black” to “white”(raising time) and from “white” to “black”(falling time), respectively. Refer to figure as below.Note 4. Definition of Reflectance:The Reflectance is expressed as:R = Reflectance Factor white board x (L center / L white board )L center is the luminance measured at center in a white area. L white board is the luminance of a standard white board.Note 5. Definition of contrast ratio:The contrast ratio (CR) is the ratio between the reflectance in a full white area (Rl) and reflectance in a dark area (Rd).RdRl(CR) ratio Contrast =S i g n a l (R e l a t i v e V a l u e )"Black"0 %90 %100 %H. Reliability Test ItemsTest Condition Condition Remark1 High-TemperatureOperationTamb=+50℃, RH=30% for 240hrs IEC 60068-2-2BpAt the end of the test electric,mechanical,and optical specifications shall besatisfied.2 Low-TemperatureOperationTamb=0℃for 240hrs IEC 60068-2-2AbAt the end of the test electric,mechanical,and optical specifications shall besatisfied.3 High-TemperaturefunctionalTamb=+60℃, RH=26% for 240hrs IEC 60068-2-2BpAt the end of the test electric,mechanical,specifications shall be satisfied.4 Low-TemperaturefunctionalTamb=-10℃for 240hrs IEC 60068-2-2AbAt the end of the test electric,mechanical,specifications shall be satisfied.5 High-TemperatureStorageTamb=+70℃, RH=23% for 240hrs IEC 60068-2-2BpAt the end of the test electric,mechanical,and optical specifications shall besatisfied.6 Low-TemperatureStorageTamb=-25℃for 240hrs IEC 60068-2-2AbAt the end of the test electric,mechanical,and optical specifications shall besatisfied.7 High-Temperature,High-HumidityOperationTamb=+40℃, RH=90% for 168hrs IEC 60068-2-3CAAt the end of the test electric,mechanical,specifications shall be satisfied.8 High-Temperature,High-HumidityStorageTamb=+60℃, RH=80% for 240hrs IEC 60068-2-3CAAt the end of the test electric,mechanical,specifications shall be satisfied.9 Temperature Cycle 1 Cycle：[-25∘C 30min] ->[+70∘C 30min]：100 cyclesIEC 60068-2-14At the end of the test electric,mechanical,specifications shall be satisfied.10 Sunlight effect1120mW/cm2 for 168hrs, 40℃IEC 60068-2-5Sa At the end of the test electric,mechanical, and optical specifications shall be satisfied.11 Package Vibration 1.04G, Frequency：10 ~ 500HZDirection：X, Y, ZDuration： 1 hours in eachdirectionAt the end of the test electric,mechanical,and optical specifications shall besatisfied.12 Package Drop Impact Drop from height of 100 cm onconcrete surface.Drop sequence：1 corner, 3edges, 6 faces one drop for each.At the end of the test electric,mechanical,and optical specifications shall besatisfied.13Electrostatic discharge Air-mode : +/- 8kV Contact-mode : +/- 4kV IEC 61000-4-2At the end of the test electric,mechanical, specifications shall be satisfied. (Note. 3) 14 Altitude test Operation700hPa(=3,000m) 48hrsAt the end of the test electric,mechanical, specifications shall be satisfied.15 Altitude test Storage 260hPa(=10,000m) 48hrsAt the end of the test electric,mechanical, specifications shall be satisfied.16FPC Soldering StrengthPull the FPC soldered part with a force of 500g in the horizontal and vertical directionsAt the end of the test electric,mechanical, specifications shall be satisfied.17FPC bending PerformanceApply MIT method.Bending rate radius ：1.0mm Weight 500gf, Bending angle ：±135∘Bending cycle ：20 timesAt the end of the test electric,mechanical, specifications shall be satisfied.18Stylus TappingPOLYACETAL Pen ：Top R0.8mmLoad ：300gf Speed ：3 times/sec Total 13,500 timesPass criteria - no glass breakage or damage to microcapsules.Note 1. Tamb: Ambient Temperature = 25℃Note 2. In the standard conditions, there is not display function NG issue occurred. All the cosmetic specification is judged before the reliability stress.Note 3. ESD testing method.1. Ambient: 24~26℃, 56~65%RH, atmospheric pressure : 940~960hPa2. Instruments:NoisekenESS-2000,3. Operation System: AUO pattern generator4. Test Mode: Non-operating mode, test pattern: chess5. Test Method:a. Contact Discharge: 150pF(330Ω) 1sec, 8 points, 25 times/pointb. Air Discharge: 150pF(330Ω) 1sec, 8 points, 25 times/point6. Test point:I. Packing and Marking1. Packing Form2. Module/Panel Label InformationThe module/panel (collectively called as the “Product”) will be attached with a label of Shipping Number which represents the identification of the Product at a specific location.Refer to the Product outline drawing for detailed location and size of the label. The label is composed of a 22-digit serial number and printed with code 39/128 with the following definition:3. Carton Label InformationThe packing carton will be attached with a carton label where packing Q’ty, AUO Model Name, AUO Part Number, Customer Part Number (Optional) and a series of Carton Number in 13 or14 digits are printed. The Carton Number is apparing in the following format:Refer to the drawing of packing format for the location and size of the carton label.J. Application Note1. Application CircuitPrecautions1. Do not twist or bend the module and prevent the unsuitable external force for display moduleduring assembly.2. Adopt measures for good heat radiation. Be sure to use the module with in the specifiedtemperature.3. Avoid dust or oil mist during assembly.4. Follow the correct power sequence while operating. Do not apply the invalid signal, otherwise,it will cause improper shut down and damage the module.5. Less EMI: it will be more safety and less noise.6. Please operate module in suitable temperature. The response time & brightness will drift bydifferent temperature.7. Be sure to turn off the power when connecting or disconnecting the circuit.8. Display surface never likes dirt or stains.9. A dewdrop may lead to destruction. Please wipe off any moisture before using module.10. High temperature and humidity may degrade performance. Please do not expose themodule to the direct sunlight and so on.11. Acetic acid or chlorine compounds are not friends with display module.12. Static electricity will damage the module, please do not touch the module without anygrounded device.13. Do not disassemble and reassemble the module by self.14. Be careful do not touch the rear side directly.15. No strong vibration or shock. It will cause module broken.16. Storage the modules in suitable environment with regular packing.17. Be careful of injury from a broken display module.18. Please avoid the pressure adding to the surface (front or rear side) of modules, because itwill cause the display non-uniformity or other function issue.。

液晶驱动板用户手册

PCB-800099驱动板1.产品说明：本驱动板可以1，1路VGA信号输入2，2路A V信号输入3，1路HDMI信号输入,且本IC支持的是HDMI1.14，1路倒车信号输入5，支持宽电压输入，并可以在，5V-24V之间正常工作，6，标准背光6PIN，接口，可外接高压板7，驱动板集成液晶屏LED背光驱动板路，8，标准LVDS信号输出，可支持单6，单8，双6，双8等标准的LVDS信号的液晶屏,但只支持屏供电为3.3V的液晶屏9，标准按键板接口，并支持双色LED指示灯显示10，支持TTL信号输出，可支持AT070TN92,AT065TN14AT080TN52AT090TN12AT090TN10AT070TN90AT070TN93AT070TN94等，通用50PIN接口的TTL液晶屏11,本驱动板最大输出显示分辨率为1920X108012，支持倒车控制，并显示A V2上，倒车电压支持50V以内的电压输入13，本驱动板定位孔为四个2 接口功能说明位号功能说明备注RCA1 A V输入TP1 A V信号输入和倒车电压输入口J4 VGA输入DB15 VGA输入HDMI HDMI输入HDMI标准为1.1DCIN 电源输入J3 电源输入J1 外接高压板口J7 LED背光座CON1 TTL-50PIN信号输出CN1 LVDS信号输出J6 按键，遥控，LED指示灯接口3，VGA模式640X480 支持800X600 支持1024X768 支持1024X600 支持1280X1024 支持1366X768 支持1440X900 支持....... .......1920X1080 支持需要支持其它分辨率，可以后续增加4，A V模拟NTSC 支持PAL 支持5产品外观图6产品尺寸图7接口功能详细说明7.1J6 按键板，遥控器输入接口序号定义说明1 5V 遥控器供电，实为3.3V2 GND 地3 IR 遥控输入4 POWER 开关机功能5 MENU 菜单显示功能6 + 加7 _ 减8 SOURCE 信号源转换9 LED-R LED指示灯10 LED-G LED指示灯DB15--VGA信号输入接口序号定义说明1 D-15 标准接口J1 高压板接口1 +12V 正电源输入2 +12V 正电源输入3 EN 高压板开关信号4 空空5 GND GND6 GND GNDCN1-----LVDS屏接口序号定义说明1 VCC 液晶屏供电2 VCC 液晶屏供电3 VCC 液晶屏供电4 GND 地5 GND 地6 GND 地7 LAX0+ LVDS信号8 LAX0- LVDS信号9 LAX1+ LVDS信号10 LAX1- LVDS信号11 LAX2+ LVDS信号12 LAX2- LVDS信号13 GND14 GND15 LACK+ LVDS信号16 LACK- LVDS信号17 LAX3+ LVDS信号18 LAX3- LVDS信号19 LBX0+ LVDS信号20 LBX0- LVDS信号21 LBX1+ LVDS信号22 LBX1- LVDS信号23 LBX2+ LVDS信号24 LBX2- LVDS信号25 GND26 GND27 LBCK+ LVDS信号28 LBCK- LVDS信号29 LBX3+ LVDS信号30 LBX3- LVDS信号J3-DCIN 电源接口1 +12V 正电源输入2 +12V 正电源输入3 GND GND4 GND GNDHDMI 接口1 HDMI标准接口标准线材可用J5,A V信号和倒车控制电源接口1 ACC 倒车电压输入，12V输入后强制到A V22 A V1 A V1输入3 GND GND4 A V2 A V2输入5 GND GNDJ4-VGA IN1 GND GND2 V V3 H H4 GND GND5 R R6 GND 地7 G G8 GND 地9 B B10 GND 地11 SDA 升级用12 SCL 升级用CON1,接口定义8 运输，存储，使用要求1，不要重压和弯折变形2，防静电和水3，相对湿度，小于80% 4, 使用温度-1-度--+60度5，使用湿度0-+40度。

1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。

3.1. Absolute Maximum Rating.............................................................................................. 5 3.1.1. Typical Operation Conditions.................................................................................. 6 3.1.2. Current Consumption ............................................................................................. 7 3.1.3. Backlight Driving Conditions ................................................................................... 7
3.2. Power Sequence ............................................................................................................ 8 3.3. Timing Characteristics .................................................................................................... 9
3.3.1. AC Electrical Characteristics .................................................................................. 9 3.3.2. Data Input Format................................................................................................. 10 3.3.3. Timing................................................................................................................... 11 4. Optical Specifications............................................................................................................ 12 5. Reliability Test Items ............................................................................................................. 16 6. General Precautions ............................................................................................................. 17 6.1. Safety ........................................................................................................................... 17 6.2. Handling ....................................................................................................................... 17 6.3. Static Electricity ............................................................................................................ 17 6.4. Storage ......................................................................................................................... 17 6.5. Cleaning ....................................................................................................................... 17 7. Mechanical Drawing ............................................................................................................. 18 8. Package Drawing ................................................................................................................. 19 8.1 Packaging Material Table.............................................................................................. 19 8.2 Packaging Quantity ...................................................................................................... 19 8.3 Packaging Drawing....................................................................................................... 20
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
INNOLUX 1. General Specifications
SPEC NO.: A070-94-TT-01 Date :2009/07/07 Page:1/20
INNOLUX DISPLAY CORPORATION
LCD MODULE
S P E C I F I C AT I O N
Customer: Model Name: SPEC NO.: Date: Version:
AT 0 7 0 T N 9 4 A0 7 0 - 9 4 - T T- 0 1 2009/07/07 01
RGB-stripe
10 Interface
Digital
11 Backlight power consumption 1.674W (Typ.)
12 Panel power consumption
0.226W (Typ.)
13 Weight
(150g) (Typ.)
Note 1: Refer to Mechanical Drawing.
David Lee
2009/07/07
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
Version Pre-Spec.01
Record of Revision
InnoLux copyright 2004 All rights reserved, Copying forbidden.
5 Dot pitch
0.0642(W) × 0.1790(H) mm
6 Active area
154.08(W) × 85.92(H) mm
7 Module size
164.9(W) ×100.0(H) ×5.7(D) mm
8 Surface treatment
Anti-Glare
9 Color arrangement
TFT LCD Panel Driving Section
FPC Connector is used for the module electronics interface. The recommended model is FH12A-50S-0.5SH manufactured by Hirose.
Pin No. Symbol I/O
Function
Remark
1
VLED+
P Power for LED backlight (Anode)
2
VLED+
P Power for LED backlight (Anode)
3
VLED-
Revise Date Page
Content
2009/07/07
Initial Release
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
INNOLUX
Contents
1. General Specifications ............................................................................................................ 1 2. Pin Assignment....................................................................................................................... 2 3. Operation Specifications ......................................................................................................... 5