路灯模组参数

ProductName CertaFlux PLM II 3000lm 740 Gen1
Description PLM Order code
929000895808
Status
Preliminary product datasheet
1 Document scope
This Product Datasheet covers the electrical, optical, mechanical, environmental and thermal characteristics and acceptance requirements of the Philips Certaflux Protected LED Module (PLM) II, an IP66 module with integrated heatsink and optics. Optical performance of PLM II is included. The product specifications as mentioned in this document are applicable for products specified in Table 1. Product description
12NC Philips CertaFlux PLM II 3000lm 740 Gen1
929000895808 CertaFlux PLM 2/3 multi-connector 929000895908 CertaFlux PLM 4/5 multi-connector
929000896008 Xitanium 50W 0.70A 230V-2C I67 929000846808 Xitanium 75W 0.70A 230V-3C I67 929000846508 Xitanium 150W 0.70A 230V-6C I67
929000846008
Table 1: Products for which this technical specification is applicable
ProductName CertaFlux PLM II 3000lm 740 Gen1
Description PLM Order code
929000895808
Status
Preliminary product datasheet
2 Product components
Part
Count Lens Single glass lens 1 PCB IMS 1.6 mm
1 LEDs Mid power CRI 70 4000K 36 Heatsink Metal plate heatsink
1 Bracket For glass mounting and IP66 rating 1 Cable gland IP66 rating 1 Breather
1 IP sealing Silicon Gasket for IP66 rating
1 IP 67 Cable
2 lead wire from L2 to driver with end connector 1 2/
3 multi
connector cable For 2or 3 module serial connection 1 4/ 5 multi
connector cable
For 4 or 5 module serial connection
1
Table 2: Product components for which this technical specification is applicable
3 Optical distribution
Figure 1: Polar intensity diagram
ProductName CertaFlux PLM II 3000lm 740 Gen1
Description PLM Order code
929000895808
Status
Preliminary product datasheet
4 Product dimensions
RLM Gen2
4.1
Product dimensions as reference (mechanical model leading)
Dimensions
L mm Length of the module
300.0 Lm mm Length from mounting holes 286 ± 0.5 W mm Width of the module
70.0 Wm mm Width from mounting holes 30.0 H
mm
Height of the module
75.0
Table 3. RLM Gen2 Dimensions Figure 2. RLM Gen2 drawing (tbd)
ProductName CertaFlux PLM II 3000lm 740 Gen1
Description PLM Order code
929000895808
Status
Preliminary product datasheet
5 Electrical interfaces
PLM II modules can be connected using the cable interface as specified below. This cable allows connection with fixed output drivers and serial connection from 1 and up to 5 modules.
Figure 3. IP67 connector clip function
Figure 4. CertaFlux PLM 2/3 multi-connector
Figure 5. CertaFlux PLM 4/5 multi-connector
ProductName CertaFlux PLM II 3000lm 740 Gen1
Description PLM Order code
929000895808
Status
Preliminary product datasheet
6 Performance specification
The following paragraphs contain the performance of PLM II. Table 5 contains performance specification as has been estimated and evaluated at Tcase 65o C and drive current of 700mA.
Performance specifications at Tcase 65o C
6.1
Initial Lumens Φinit Lm Initial luminous flux (0 hr) 2700 3000 3300
Module Efficacy ηmodule lm/W Initial Efficacy (0 hr)
113
System Efficiency ηdriver lm/W
103 Initial Power Consumption Pel ,init W Initial Power Consumption (0 hr) 24.5 26.5 28.5 CCT CCT K Nominal colour temperature 4000 Color point x x [-]
Target colour point x
0.382
Color point y
y [-] Target colour point y
0.381
Initial Colour Accuracy ∆uv
SDCM
Initial standard deviation colour matching with respect to the target colour point (x,y)
7
Table 5.1 Performance specification of the Philips RLM Gen2 at typical operational conditions
Note:
• Philips maintains a tolerance +/- 6.5% on luminous flux measurements, +/- 0.06V on forward voltage
measurements, +/- 2 on CRI measurements and +/- 5% on CCT measurements
ProductName CertaFlux PLM II 3000lm 740 Gen1
Description PLM Order code
929000895808
Status
Preliminary product datasheet
Color consistency
6.2Target color coordinates as specified for drive current 700mA, Tcase 65°C.
Figure 5. Color consistency
7 Thermal management
The Philips PLM II module is equipped with an integrated heatsink to enable lifetime statement. There is no thermal protection i.e. NTC to prevent overheating and extreme lifetime degradation of the LEDs.
Thermal measurement
7.1On the back of the module there is a Tcase (Tc) point, which should be used for all temperature measurements. The location for measuring the maximum temperature of the module is in the middle at the bottom of the heatsink.
Thermal specifications
7.2
item
symbol unit Description
max Case
temperature T case
°C
Case temperature: temperature at which the module operates within specifications 65
Delta T
∆T
°C
The maximum temperature difference between Tambient and Tcase
40
Table 6. Thermal ratings of the system
0.360
0.370
0.380
0.390
0.400
0.352
0.362
0.372
0.382
0.392
0.402
0.412
C i e y
Cie x
4000K
5.0 SDCM BBL
ProductName CertaFlux PLM II 3000lm 740 Gen1
Description PLM Order code
929000895808
Status
Preliminary product datasheet
8 Surge protection
A surge solution with by-pass capacitors is implemented on the L2 board to protect them from electrical
overstress. Capacitors will bypass excessive current to the ground. The solution is valid for all the released driver and module combinations.
9 Compatible system drivers
1x fits 2x fits 3x fits 4x fits 5x
fits
Table 7 RLM Gen2 mapping with IP 65 drivers 10 Product usage conditions
The Philips PLM II modules as sold under the following conditions. • Product is suitable for direct exposure to moisture, dust, etc. • Product is suitable for dry and damp locations
• Product is protected against powerful water jets from any direction shall (IP66).
11 RoHS & Reach
The modules are compliant with European Directive 2011/65/EU recasting 2002/95/EC on Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment (RoHS). The modules are complaint to Reach as defined by the EU Chemical Agency.
12 Certification
To be defined
ProductName CertaFlux PLM II 3000lm 740 Gen1
Description PLM Order code
929000895808
Status
Preliminary product datasheet
13 Electrostatic device (ESD) measures
Philips PLM II module system does not require ESD measures in a production environment. • Do not use damaged or defective modules • Do not touch LEDs
• Do not drop the LED module or let any object fall on top of the module as this may damage the insulation
layer of the LED board. Do not use the LED module if it has been dropped or an object has fallen on it and there are visible defects or damage.
14 Appendix
Abbreviations and definitions
Abbreviation
Definition
12NC Standard 12-digit number for Philips coding CRI Color Rendering Index LED Light Emitting Diode
NTC Negative Temperature Coefficient PCB Printed Circuit Board Philips
Philips Lighting B.V.
Table 8: Abbreviation and definitions。