5050RGB-6-s

东莞市东赑光电有限公司

DONGGUAN DONGBI OPTOELECTRONICS CO.，LTD.

承认书

SPECIFICATION FOR APPROVAL

客户名称Customer：

产品型号Model：DOB-5050RGB-6-s

承认书编号No.：101153

制作日期Date：2016-02-21

附产品规格书Enclosure is the specification

地址：东莞市茶山镇文化路66号3F

电话Tel: 0086-769-89879224

传真Fax: 0086-769-89037265

Email: xuchaobing@

Website:

Modify records

Technical Data Sheet

TOP View White LED (5050)

For: IF= 60mA

Contents

1. Features

2. Applications

3. Package outline dimension

4. Absolute maximum ratings

5. Electrical-optical characteristics

6. Typical electro-optical characteristics curves

7. Wavelength

8. Luminous intensity

9. Forward voltage

10. Reliability test items and conditions

11. Precautions for use

12. Package method

1.0 Features:

1.1 Package: 5.0*5.0*1.6mm (TOP view white LED) 1.2 Colorless clear window. 1.3 Interior reflector. 1.4 Wide viewing angle.

1.5 Suitable for vapor-phase reflow, infrared reflow and wave solder processes. 1.6 Computable with automatic placement equipment. 1.7 Pb-free.

1.8 Comply ROHS standard

2.0 Applications:

2.1 LCD back light. 2.2 Mobile phones: LCD.

2.3 Status indicators: Consumer & industrial electronics.

2.4 General use.

3.0 Package Outline Dimension:

3.1 NOTES:

3.1.1 All dimensions are in millimeters (inches). 3.1.2 Tolerance is ±0.10mm unless otherwise specified.

3.1.3 Specifications are subject to change without notice.

4.0 Absolute Maximum Ratings(Ta=25℃)

4.1 ＊1 I FP condition: pulse of 1/10 duty and 0.1ms width.

5.0 Electrical-optical characteristics(Ta=25℃)

5.1 Note:

5.1.1 Tolerance of luminous intensity is ±10% 5.2.2 Tolerance of forward voltage is ±0.05V

6.0 Typical Electro-Optical Characteristics Curves 6.1 Electro-Optical Characteristics Curves (R)

6.2 Electro-Optical Characteristics Curves (G)

6.3 Electro-Optical Characteristics Curves (B)

7.0 Wavelength (tolerance is ±0.05nm@If=60mA):

8.0 Luminous intensity (tolerance is ±10%@ If=60mA):

9.0 Forward voltage (tolerance is ±0.05V@If=60mA):

10.0 Reliability test items and conditions:

11.1.1 Iv: Below 50% of initial values

11.1.2 Vf: Over 20% of upper limit value

11.1.3 IR: Over 2 times of upper limit value

10.2 Note:

10.2.1 Measurement shall be taken between 2 hours and after the test LED have been returned to

normal ambient conditions after completion of each test.

11.0 Precautions for use :

11.1 Customer must apply the current limiting resistor in the circuit so as to drive the LEDs within

the rated current. Otherwise slight voltage shift maybe will cause big current change and burn out will happen.

11.2 Also, caution should not be taken to overload the LEDs with instantaneous high voltage at the turning

ON and OFF of the circuit.

11.3 Storage:

12.3.1 SMD LED must be stored in dry, the humidity should be kept less than 60%RH to prevent damping.

12.3.2 Ensure the aluminum foil bag is perfectly sealed before use. Any leaking or damage of the

bag is not acceptable, should return back to the factory for repacking.

12.3.3 as the product is perfectly sealed and stored within 60%RH of humidity, the product can be

used without any further baking process in a month. If the product is stored over a month,

it should be baked without the bag before use. Baking treatment: 75℃ for 72 hours. Any unsealed

product should be used up within 6 hours, otherwise the product should follow the baking

treatment to prevent any disability incurred of the product

12.3.4 reflow soldering is recommended for this product. Any soldering with temperature over 300℃

is not recommended.

12.3.5 reflow soldering temperature should be set around 230℃, and should not over 250℃. Reflow

soldering should be done within 7 minute, the time used in high temperature zone should less

than 7 seconds. Different solder paste require different soldering temperature, we recommend

to use hypothermia solder paste since it lower the expansion rate of the SMD LED. We also