SZ604D中文资料
SA605D中文规格书
SA605数据手册-SA605高性能低功率的混频器（中频调频系统）-菲利普半导体（1992年11月3日）简介：SA605是一种单片式的高性能、低功耗、能够调频中频系统的混频器/振荡器，有两个限幅中频放大器、积分检波器，可以进行噪声抑制，对数信号接受强度指示（RSSI）器和电压调节器，SA605结合西格尼蒂克公司的SA602和SA604A的功能，但具有更高的混频器输入截点，更高的中频带宽（25MHz）和温度补偿的RSSI以及限制器，可以应用于更高的性能要求。
该芯片提供20引脚DIP(双列直插式塑料封装)、20引脚SOL （表面安装微型封装）和20引脚SSOP（小外形封装）。
SA605和SA615在功能上属于相同的类型。
两个设备之间的不同之处在于保证规格。
SA615具有较高的Icc，较低的输入三阶截点，较低的变频混频器增益，更低的增益限，更低的调幅抑制，低SINAD（信纳比），THD（总谐波失真）较高，以及比SA605更高的RSSI误差。
无论是SA605或SA615都满足EIA（电子工业协会）的AMPS和TACS蜂窝式无线应用。
更多技术信息，请参考应用手册AN1994，1995和1996，其中包括示例应用程序图和该产品的完整概述和参考插图。
应用：•蜂窝无线中频调频•高性能通信接收器•单次转换VHF/UHF接收器•SCA（软件通信体系框架）接收器•射频电平表•频谱分析仪•仪表•FSK和ASK数据接收机•对数放大器•宽带低电流放大引脚配置：1.RF IN2.RF旁路3.XTAL OSC（外部时钟输入振荡器）4.XTAL OSC5.静音输入6.Vcc7.RSSI输出8.静音音频输出9.非静音音频输出10.正交输入20.混频输出19.中频放大去耦端18.中频放大输入17.中频放大去耦端16.中频放大输出15.接地14.限幅器输入13.限幅器去耦端12.限幅器去耦端11.限幅器输出•低功耗：6V时通常5.7mA•混频器输入>500MHz•混频器的转换功率增益在45MHz下为13dB•晶振有效值到达150MHz（LC振荡器达到1GHz；LO本机振荡器可以注入频率）•中频放大器/限幅器的增益为102分贝•限值为25MHz的小信号带宽•温度补偿的对数接收信号强度指示（RSSI）有过量的90分贝动态范围•两个音频输出-静音，非静音•低外部元件数量；适用于晶体/陶瓷/LC过滤器•卓越的灵敏度；0.22μV转换成50Ω的匹配网络时，SINAD（信噪和失真比）为12分贝（频率为1kHz时、RF在45MHz时、IF在455kHz时）（0.22µV into50Ωmatching network for12dB SINAD(Signal to Noise and Distortion ratio)for1kHz tone with RFat 45MHz and IF at455kHz）•SA605符合蜂窝无线电规格•ESD（静电释放）固化订购信息：①：20引脚DIP(双列直插式塑料封装)SA605N②：20引脚SOL（表面安装微型封装)SA605D③：20引脚SSOP（小外形封装）SA605DK1.RF IN20.混频输出2.RF旁路19.中频放大去耦端3.XTAL OSC(外部时钟输入振荡器)18.中频放大输入4.XTAL OSC17.中频放大去耦端5.静音输入16.中频放大输出6.Vcc15.接地7.RSSI输出14.限幅器输入8.静音音频输出13.限幅器去耦端9.非静音音频输出12.限幅器去耦端10.正交输入11.限幅器输出绝对最大额定值：①：单电源电压②：存储温度范围③：热阻抗直流电气特性：（除了另作说明的情况一般默认：V CC=+6V,T A=25°C）①：电源供应电压范围②：直流漏电流③：静音开关输入阈值交流电气特性：（除了另作说明的情况一般默认：V CC=+6V,T A=25°C，射频频率为45MHz与14.5dbv的射频输入升压；中频频率为455KHZ；R17为5.1K ；射频电平为-45dbm；FM调制为1kHz与±8kHz的峰偏差。
深圳四万通变频器说明书
深圳四万通变频器说明书一、产品概述深圳四万通是一家专业生产变频器的公司，其产品广泛应用于各个领域。
本说明书将为您介绍深圳四万通变频器的特点、使用方法以及注意事项，以帮助您更好地了解和使用我们的产品。
二、产品特点1.高效节能：深圳四万通变频器采用先进的变频控制技术，能够根据负载情况自动调节输出功率，实现能耗的最优化。
2.稳定可靠：产品采用高质量的电子元件和先进的控制算法，具有良好的稳定性和可靠性，能够满足各种复杂工况的需求。
3.精确控制：变频器具备精确的速度和扭矩控制功能，可以满足不同设备的精细运行要求。
4.操作简便：产品具备友好的人机界面，操作简单方便，适用于各种应用场景。
5.安全可靠：变频器具备多重保护功能，包括过载保护、短路保护、过温保护等，确保设备和人员的安全。
三、使用方法1.安装：在安装变频器时，请确保电源已切断，并按照产品说明书中的指引正确连接电源和负载。
2.参数设置：使用前，请根据实际需求设置好相关参数，包括电机额定功率、额定电流等。
3.启动：接通电源后，按照说明书中的步骤进行启动操作，并观察指示灯的状态，确保正常运行。
4.运行控制：通过控制面板或外部控制信号，可以实现变频器的启停、速度调节等功能。
5.故障排除：如果发生故障，请首先检查电源和负载的连接是否正常，然后参考说明书中的故障排除方法进行处理。
四、注意事项1.请勿将变频器安装在有腐蚀性气体或易燃易爆场所。
2.避免长时间连续运行，适当休息以延长变频器的使用寿命。
3.请勿随意更改变频器的参数设置，以免影响设备的正常运行。
4.使用前请确保电源和负载的额定电压和额定电流与变频器匹配。
5.定期检查变频器的散热器是否清洁，保持通风良好。
6.禁止非专业人员拆卸和维修变频器，如需维修请联系售后服务。
五、结语深圳四万通变频器是一款高性能、稳定可靠的产品，具有广泛的应用领域。
通过本说明书，您可以更好地了解和使用我们的产品，希望能为您的工作和生活带来便利和效益。
HT604中文资料
HT604L/614/692318Series of Decoders1April 24,2000Features·Operating voltage:2.4V~12V·Low power and high noise immunity CMOS technology·Low standby current·Capable of decoding 18bits of information ·Pairs with Holtek ¢s 318series of encoders ·9~10address pins ·2~8data pins·Trinary address setting·Two times of receiving check·Built-in oscillator needs only a 5%resistor ·Valid transmission indicator·Easy interface with an RF or an infrared transmission medium·Minimal external components·Package information:refer to Selection TableGeneral DescriptionThe 318decoders are a series of CMOS LSIs for remote control system applications.They are paired with the 318series of encoders.For proper operation,a pair of encoder/decoder pair with the same number of address and data for-mat should be selected (refer to the encoder/de-coder cross reference tables).The 318series of decoders receive serial address and data from that series of encoders that are transmitted by a carrier using an RF or an IR transmission medium.It then compares the se-rial input data twice continuously with its local address.If no errors or unmatched codes areencountered,the input data codes are decoded and then transferred to the output pins.The VT pin also goes high to indicate a valid transmis-sion.The 318decoders are capable of decoding 18bits of information that consists of N bits of address and 18-N bits of data.To meet various applica-tions they are arranged to provide a number of data pins whose range is from 0to 8and an ad-dress pin whose range is from 8to 18.In addi-tion,the 318decoders provide various combinations of address/data number in differ-ent packages.Applications·Burglar alarm system·Smoke and fire alarm system ·Garage door controllers ·Car door controllers ·Car alarm system ·Security system ·Cordless telephones·Other remote controlsystemsSelection TableFunction AddressNo.DataVT Oscillator Trigger PackagePart No.No.TypeHT604L104LÖRC oscillator DIN active²Hi²20DIP/SOP HT614104MÖRC oscillator DIN active²Hi²20DIP/SOP HT692102MÖRC oscillator DIN active²Hi²18DIPNote:Data type:M stands for momentary type data output.L stands for latch type data output.VT can be used as a momentary data output.Block DiagramNote:The address/data pins are available in various combinations(refer to the address/data table).2April24,2000Pin AssignmentLatch series Momentary seriesPin DescriptionPin Name I/O InternalConnection DescriptionA0~A12I TRANSMISSIONGATE Input pins for address A0~A12settingThey can be externally set to VDD,VSS or left open.D10~D17O CMOS OUT Output data pinsDIN I CMOS IN Serial data input pinVT O CMOS OUT Valid transmission,active highOSC1I OSCILLATOR Oscillator input pinOSC2O OSCILLATOR Oscillator output pinVSS¾¾Negative power supply,groundVDD¾¾Positive power supply3April24,2000Absolute Maximum RatingsSupply Voltage...............................-0.3V to13V Storage Temperature.................-50°C to125°C Input Voltage.................V SS-0.3V to V DD+0.3V Operating Temperature..............-20°C to75°CNote:These are stress ratings only.Stresses exceeding the range specified under²Absolute Maxi-mum Ratings²may cause substantial damage to the device.Functional operation of this de-vice at other conditions beyond those listed in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability.Electrical Characteristics Ta=25°CSymbol ParameterTest ConditionsMin.Typ.Max.Unit V DD ConditionsV DD Operating Voltage¾¾3¾12VI STB Standby Current 5VOscillator stops¾0.11m A 12V¾24m AI DD Operating Current5V No loadf OSC=100kHz¾0.21mAI O Data Output Source Current(D10~D17)5VV OH=4.5V-0.5-1¾mAData Output Sink Current(D10~D17)V OL=0.5V0.51¾mAI VT VT Output Source Current5VV OH=4.5V-2-4¾mA VT Output Sink Current V OL=0.5V12¾mAV IH²H²Input Voltage5V¾ 3.5¾5VV IL²L²Input Voltage5V¾0¾1Vf OSC Oscillator Frequency10V R OSC=330k W¾100¾kHz4April24,2000Functional DescriptionOperationThe318series of decoders provide various com-binations of address and data pins in different packages.It is paired with the318series of encoders.The decoders receive data transmit-ted by the encoders and interpret the first N bits of the code period as address and the last 18-N bits as data(where N is the address code number).A signal on the DIN pin then acti-vates the oscillator which in turns decodes the incoming address and data.The decoders will check the received address twice continuously. If all the received address codes match the con-tents of the decoder¢s local address,the18-N bits of data are decoded to activate the output pins,and the VT pin is set high to indicate a valid transmission.That will last until the ad-dress code is incorrect or no signal has been re-ceived.The output of the VT pin is high only when the transmission is valid.Otherwise it is always low.Output typeThere are two types of output to select from:·Momentary typeThe data outputs follow the encoder during a valid transmission and then reset.·Latch typeThe data outputs follow the encoder during a valid transmission,and are then latched in this state until the next valid transmission occurs.FlowchartNote:The oscillator is disabled in the standby state and activated as long asa logic²high²signal is applied to theDIN pin.i.e.,the DIN should be kept²low²if there is no signal input.5April24,2000Decoder timingEncoder/Decoder selection tables ·Latch type of data outputPart No.DataPins AddressPins VT Pair EncoderPackageEncoder DecoderDIP SOP SKDIP DIP SOP SKDIPHT604L410ÖHT6002020¾2020¾HT620720¾·Momentary type of data outputPart No.DataPins AddressPins VT Pair EncoderPackageEncoder DecoderDIP SOP SKDIP DIP SOP SKDIPHT692210ÖHT68018¾¾18¾¾HT614410ÖHT6002020¾2020¾HT620720¾6April24,2000Address/Data sequenceThe following provides a table of address/data sequence for various models of the 318series decoders.A correct device should be selected according to the sindividual address and data requirements.Part No.Address/Data Bits0~3456~91011121314151617HT604L A0~A3A4¾A6~A9¾A11D12D13D14D15¾¾HT614A0~A3A4¾A6~A9¾A11D12D13D14D15¾¾HT692A0~A3¾¾A6~A9¾A11A12¾D14D15¾¾Note:²¾²is a dummy code which is left ²open ²and not bonded out.Oscillator frequency vs supply voltageThe recommended oscillator frequency is f OSCD (decoder)@f OSCE (encoder)7April 24,2000C 2222222 2.Application CircuitsNote:Typical infrared receiver:PIC-12043T/PIC-12043C(KODENSHI CORP.)or LTM9052(LITEON CORP.)Typical RF receiver:JR-200(JUWA CORP.)RE-99(MING MICROSYSTEM,U.S.A.)8April24,20009April 24,2000Copyright ã2000by HOLTEK SEMICONDUCTOR INC.The information appearing in this Data Sheet is believed to be accurate at the time of publication.However,Holtek assumes no responsibility arising from the use of the specifications described.The applications mentioned herein are used solely for the purpose of illustration and Holtek makes no warranty or representation that such applications will be suitable without further modification,nor recommends the use of its products for application that may pres-ent a risk to human life due to malfunction or otherwise.Holtek reserves the right to alter its products without prior notification.For the most up-to-date information,please visit our web site at .Holtek Semiconductor Inc.(Headquarters)No.3Creation Rd.II,Science-based Industrial Park,Hsinchu,Taiwan,R.O.C.Tel:886-3-563-1999Fax:886-3-563-1189Holtek Semiconductor Inc.(Taipei Office)5F,No.576,Sec.7Chung Hsiao E.Rd.,Taipei,Taiwan,R.O.C.Tel:886-2-2782-9635Fax:886-2-2782-9636Fax:886-2-2782-7128(International sales hotline)Holtek Semiconductor (Hong Kong)Ltd.RM.711,Tower 2,Cheung Sha Wan Plaza,833Cheung Sha Wan Rd.,Kowloon,Hong Kong Tel:852-2-745-8288Fax:852-2-742-8657。
ZSN603 读卡专用芯片说明书
ZSN603读卡专用芯片DS01060100 1.0.05 Date:2021/02/02—————————————— 概述ZSN603读卡专用芯片是广州致远微电子有限公司开发的一款集成了卡操作指令的芯片，用户不需要进行编程，只需要发送简单的命令，即可完成对卡片的读写。
外部电路设计简单，可以快捷、高效地开发出产品。
—————————————— 产品特性 ◆ 宽工作电压2.8V~3.6V ；◆支持ISO/IEC 14443 TypeA/B 读写器模式； ◆ 集成 TypeB 、PLUS CPU 、Mifare UltraLight 、Mifare S50/S70、SAM 卡的操作命令；◆ 提供ISO14443-4 的半双工块传输协议接口，可方便支持符合 ISO14443-4A 的 CPU 卡及符合 ISO14443-4B 的 TypeB 卡片，支持ISO7816-3接口标准；◆ 支持UART 串口进行指令操作； ◆ 支持I2C 接口指令操作； ◆ 支持直接外接2个读卡天线；◆ 读卡距离可达7cm （取决于天线设计）；———————————— 产品应用 ◆ 交通票务 ◆ 智能家居 ◆ 金融财务 ◆ 医疗卫生◆ 休闲娱乐管理———————————————————————————————— 产品图片©2020 Guangzhou ZHIYUAN Micro Electronics Co., Ltd修订历史目录1. 产品简介 (1)1.1产品概述 (1)1.2产品特性 (1)1.3芯片尺寸 (1)1.4命名规则 (1)1.5产品选型表 (2)2. 硬件描述 (3)2.1引脚分布 (3)2.2引脚说明 (3)3. 电气参数 (5)3.1极限额定参数 (5)3.2芯片管脚电气特性 (5)3.3功耗特性 (5)3.4读卡特性 (5)3.5复位特性 (5)4. 典型应用 (7)4.1普通模式应用 (7)4.2八天线扩展模式应用 (7)5. 封装尺寸 (9)6. 表面贴装条件 (12)7. 存储与运输 (13)8. 包装信息 (14)9. 免责声明 (15)1. 产品简介1.1 产品概述ZSN603读卡专用芯片是广州致远微电子有限公司开发的一款集成了卡操作指令的芯片，用户不需要进行编程，只需要发送简单的命令，即可完成对卡片的读写。
深圳远景达自助收银机参数
产品细节：
尺寸：65*60*80cm
重量：23kg
用途：自助识别检测商品、称重商品，自助扫码结账收银，手机支付结账：手机二维码支付，网络支付（支付宝/微信）、人脸识别无感支付广告屏幕：26寸LCD/LED高清超薄屏幕
安装模式：立式/落地式
性能参数：
触摸屏：19寸电阻，21.5寸电容触摸控制屏
主机：工业主机系统，双核CPU，2G内存，500G硬盘
专业级现金纸币器，加强防伪。
80mm热敏打印，自动切纸和出纸
有线/WIFI连网
∙
∙处理器1037U 1.8GHz 双核
∙芯片组intel 1037U+nm70
∙主板1037U
∙存储2GB DDR3
∙硬盘32GB 固态硬盘
∙网卡集成网卡
∙显示器15英寸高清LED屏幕
∙顾客显示屏8位数码顾客显示屏
∙键盘专用PS/2键盘端口和鼠标端口
∙外设连接条码阅读器，电子秤，PC
∙360×300×410mm
∙产品重量8.5kg
∙电源电压220V或110V
∙电源功率380W
∙其它参数操作系统：Windows7
∙其它特点高触控电容屏、兼容性强、运行稳定，15寸大屏幕高触控电容屏，送58打印机∙工作环境工作温度：5-35℃，存放温度：-20-55℃
∙附赠软件清华紫光有美食云餐饮管理系统标准版
∙选配设备IC卡阅读器，磁卡阅读器
参数表：。
康海时代 NC604D 规格说明书
NC604D
规格说明书
安徽康海时代科技股份有限公司 产品技术中心2021版
证券简称：康海时代 证券代码：833422 第2页/共8页
特点
完整的软硬件自有知识产权及产品认证
支持WEB 控制台（HTTP）进行管理配置，友好的中/英文菜单配置界面 网络端通信协议支持 TCP、UDP、Telnet
采用ARM CPU 内核，主频最高72Mhz，SRAM 64K，FLASH 256K+1024K 1个10/100 Mbps 自适应网口，支持MDI/MDI-X 自适应功能
4个RS232串口，接口形式：5Pin 端子。
支持TXD、RXD、RTS、CTS、GND 串口信号 单个串口可支持2个会话
输入电压范围： DC 9~36V
证券简称：康海时代 证券代码：833422 第3页/共8页 认证和专利
康海时代、COMHIGHER、
详细规格
证券简称：康海时代 证券代码：833422 第4页/共8页
证券简称：康海时代 证券代码：833422 第5页/共8页
工作环境
工作温度
标准品：-20~75℃ 工业级：-40~85℃ 存储温度
标准品：-20~75℃ 工业级：-40~85℃
工作湿度 5~95% 存储湿度
5~95%
尺寸
串口接线定义
5PIN串口接口定义
PIN RS232
1 TXD
2 RXD
3 RTS
4 CTS
证券简称：康海时代 证券代码：833422 第6页/共8页
证券简称：康海时代 证券代码：833422 第7页/共8页 订购信息
证券简称：康海时代 证券代码：833422 第8页/共8页 配件线缆（单独选购）。
三汇示波器说明书(Ver1.0)
DST4000 和 DST1000 系列数字存储示波器用户手册
i
目录
5.1 显示区 ........................................................................................ 20 5.2 信息区域..................................................................................... 23 5.3 波形显示..................................................................................... 23
三汇系列产品
DST4000 和 DST1000 系列 数字存储示波器
Version 1.0
杭州三汇科技有限公司 www.
目录
目录
目 录 ...........................................................................................................i 版权申明 .......................................................................................................................................................................v 第 1 章 安全事项......................................................................................... 1
防腐型雷达物位计型号
防腐型雷达物位计型号防腐型雷达物位计型号1. 简介防腐型雷达物位计是一种用于测量液体、粉末和颗粒物料的高精度非接触式测量仪器。
它采用微波技术，能够在恶劣环境下进行稳定的工作，具有高精度、高可靠性、高稳定性等优点，被广泛应用于化工、石油、制药、食品等行业。
2. 型号目前市场上常见的防腐型雷达物位计型号有：（1）SITRANS LR560：西门子公司生产的一款防腐型雷达物位计，适用于各种液体和固体介质的非接触式测量。
（2）Rosemount 5400：艾默生公司生产的一款防腐型雷达物位计，适用于化学品、石油和天然气等行业。
（3）Guidense TDR2000：美国Vega公司生产的一款防腐型雷达物位计，适用于各种液体和固体介质的非接触式测量。
3. 特点（1）耐腐蚀性强：采用特殊材料制造，能够在酸碱等腐蚀性介质中长期稳定工作。
（2）测量范围广：适用于各种液体、粉末和颗粒物料的非接触式测量，可满足不同行业的需求。
（3）高精度：采用微波技术，具有高精度、高可靠性和高稳定性等优点。
（4）易安装：无需接触物料，安装简便、维护方便。
4. 应用防腐型雷达物位计广泛应用于化工、石油、制药、食品等行业。
具体应用包括：（1）化工行业：测量各种液体和固体介质的液位、料位和界面。
（2）石油行业：测量储罐内的原油、天然气等介质的液位和料位。
（3）制药行业：测量各种液体药剂的液位和料位。
（4）食品行业：测量各种粉末和颗粒物料的料位。
5. 注意事项使用防腐型雷达物位计时需要注意以下事项：（1）正确选择型号：根据实际需求选择合适的型号。
（2）安装位置：应选择在介质表面以上，以免影响测量精度。
（3）维护保养：定期检查和清洁物位计，确保其正常工作。
（4）避免干扰：防止外部电磁场等干扰物位计的正常工作。
zsld电磁铁规格书
zsld电磁铁规格书摘要：一、引言二、zsld 电磁铁的规格说明1.电磁铁的类型2.电磁铁的主要技术参数3.电磁铁的尺寸和重量三、zsld 电磁铁的工作原理1.电磁铁的磁化过程2.电磁铁的磁性强度3.电磁铁的磁极四、zsld 电磁铁的应用领域1.电磁铁在工业上的应用2.电磁铁在医疗设备上的应用3.电磁铁在科学研究上的应用五、zsld 电磁铁的维护与保养1.电磁铁的清洁与防护2.电磁铁的故障排查与维修六、结论正文：【引言】zsld 电磁铁是一款具有高磁性强度、稳定性能和广泛应用领域的电磁设备。
本规格书旨在详细介绍zsld 电磁铁的各项性能参数、工作原理、应用领域以及维护保养方法。
【zsld 电磁铁的规格说明】zsld 电磁铁采用了一种特殊的磁性材料，具有较高的磁性强度。
电磁铁的类型分为直流电磁铁和交流电磁铁两种，用户可以根据实际需求进行选择。
主要技术参数包括额定电压、额定电流、磁性强度、工作频率等，用户可以根据这些参数来判断电磁铁的性能优劣。
此外，zsld 电磁铁的尺寸和重量也都在合理范围内，方便用户进行安装和使用。
【zsld 电磁铁的工作原理】电磁铁的工作原理主要是利用电流在线圈中产生磁场，进而使磁性材料产生磁化。
磁化后的磁性材料具有磁性，可以吸引或排斥其他磁性物质。
zsld 电磁铁的磁性强度较高，可以满足大部分应用领域的需求。
磁极方面，zsld 电磁铁具有两个磁极，分别为N 极和S 极，用户可以根据需要调整磁极方向。
【zsld 电磁铁的应用领域】zsld 电磁铁广泛应用于工业、医疗设备、科学研究等领域。
在工业生产中，电磁铁可以用于电磁制动、电磁起重、电磁继电器等设备；在医疗设备中，电磁铁可以用于核磁共振成像（MRI）等设备；在科学研究中，电磁铁可以用于粒子加速器、磁悬浮列车等高精尖设备。
【zsld 电磁铁的维护与保养】为了保证zsld 电磁铁的正常工作和使用寿命，用户需要定期对其进行维护保养。
D40ML系列RFID磁锁产品说明书
1Stainless SteelPlasticDie-cast MetalMagnetic latching combines with RFID technology to deliver high holding force and tamper resistance•RFID provide s a high degree of t a mper re s i s t a nce.•Cle a n/Sa nitize in Pl a ce – s t a inle ss s teel ver s ion s a re r a ted IP69K •LED s s upport e as y f a ult di a gno s i s •In s t a ll up to 20 s witche s in s erie s•Re s idu a l m a gneti s m a ct s as light door l a tch a fter unlocking •Two a ctu a tor type s with type 4 coding•B as ic – a ll a ctu a tor s in the s y s tem a re identic a lly coded.•Unique – every a ctu a tor i s individu a lly coded. 32,000,000 code s •Both offer toler a nce for mi sa lignment•Two s witch s ize s provide multiple holding force option s •Medium Duty-S t a inle ss S teel: F1m a x (typic a l) 600N, F zh 450N -Pl as tic a nd Diec as t: F1m a x (typic a l) 900N, F zh 675N •He a vy Duty-S t a inle ss S teel: F1m a x (typic a l) 950N, F zh 700N-Pl as tic a nd Diec as t: F1m a x (typic a l) 1500N, F zh 1150N •Three c as e m a teri a l sPl as tic, diec as t met a l, 316 s t a inle ss s teel•For u s e on m a chine s with no rundown time if power i s lo s tDiagnostic Indicator FunctionYellow LED indicates OPENS hown in Gu a rd Open Po s itionGreen LED indicates CLOSEDS hown in Gu a rd Clo s ed Po sition Switch StatusGuard Green LED Yellow LEDSafety OutputLockedClo s ed S te a dy Off Clo s ed S olenoid Power OFF (unlocked)Clo s ed Fl as hing Off Open Gu a rd Open Open Off S te a dy Open Door Forced OpenOpenOffFl as hingOpenD40ML Series2Ordering InformationSwitchesSpare ActuatorsNote:S p a re a ctu a tor s a re not a v a il a ble for uniquely coded s witche s.AccessoriesNote:1.The quick di s connect c a ble h as a n identic a l c a ble pining as the Cable Wiring on p a ge 42.Y92E-M12PUR S H8S M-L di s connect c a ble s a re a l s o comp a tible with D40ML.Case Material Holding Force F1max (typical)Actuator Type Cable Configuration Model Number316 S t a inle ssS teel (IP69K)600NUnique5m C a ble D40ML-SS2-U-5M10m C a ble D40ML-SS2-U-10MPigt a il w/ M12 Connector D40ML-SS2-U-M12B as ic5m C a ble D40ML-SS2-B-5M10m C a ble D40ML-SS2-B-10MPigt a il w/ M12 Connector D40ML-SS2-B-M12 950NUnique5m C a ble D40ML-SS1-U-5M10m C a ble D40ML-SS1-U-10MPigt a il w/ M12 Connector D40ML-SS1-U-M12B as ic5m C a ble D40ML-SS1-B-5M10m C a ble D40ML-SS1-B-10MPigt a il w/ M12 Connector D40ML-SS1-B-M12Pl as tic (IP67)900NUnique5m C a ble D40ML-P2-U-5M10m C a ble D40ML-P2-U-10MPigt a il w/ M12 Connector D40ML-P2-U-M12B as ic5m C a ble D40ML-P2-B-5M10m C a ble D40ML-P2-B-10MPigt a il w/ M12 Connector D40ML-P2-B-M12 1500NUnique5m C a ble D40ML-P1-U-5M10m C a ble D40ML-P1-U-10MPigt a il w/ M12 Connector D40ML-P1-U-M12B as ic5m C a ble D40ML-P1-B-5M10m C a ble D40ML-P1-B-10MPigt a il w/ M12 Connector D40ML-P1-B-M12Diec as t Met a l(IP67)900NUnique5m C a ble D40ML-M2-U-5M10m C a ble D40ML-M2-U-M12Pigt a il w/ M12 Connector D40ML-M2-U-M12B as ic5m C a ble D40ML-M2-B-5M10m C a ble D40ML-M2-B-10MPigt a il w/ M12 Connector D40ML-M2-B-M12 1500NUnique5m C a ble D40ML-M1-U-5M10m C a ble D40ML-M1-U-10MPigt a il w/ M12 Connector D40ML-M1-U-M12B as ic5m C a ble D40ML-M1-B-5M10m C a ble D40ML-M1-B-10MPigt a il w/ M12 Connector D40ML-M1-B-M12Product Description Model Number S t a inle ss S teel; IP69K; 950N; B as ic Code; Actu a tor D40ML-SS1-B-ACTS t a inle ss S teel; IP69K 600N; B as ic Code; Actu a tor D40ML-SS2-B-ACT Diec as t Met a l; IP67; 1500N; B as ic Code; Actu a tor D40ML-M1-B-ACTDiec as t Met a l; IP67; 900N; B as ic Code; Actu a tor D40ML-M2-B-ACTPl as tic; IP67; 1500N; B as ic Code; Actu a tor D40ML-P1-B-ACTPl as tic; IP67; 900N; B as ic Code; Actu a tor D40ML-P2-B-ACTProduct Description Model Number Quick Di s connect C a ble, 8-pin M12 to Flying Le a d s, PVC J a cket, 5 Meter Length D40ML-CBL-M12-5M Quick Di s connect C a ble, 8-pin M12 to Flying Le a d s, PVC J a cket, 10 Meter Length D40ML-CBL-M12-10MD40ML Series3SpecificationsNote:When the product u s e devi a te s from the s e ass umption s (different lo a d, oper a ting frequency, etc.) the v a lue s mu s t be a dju s ted a ccordingly.Codes and StandardsIEC 60947-5-3:2013, EN 60947-5-1:2004 + AC:2005 + A1:2009, EN 60947-1:2007 + A1:2011, EN I S O 13849-1:2008 + AC:2009, EN 62061:2005 + AC:2010 + A1:2013, I S O 14119:2013, UL508Safety Classificationand Reliability Data Minimum Switched Current 10VDC 1mA Dielectric Withstand 250VAC Insulation Resistance 100M ΩShock Resistance 11m s 30GVibration Resistance 10 to 55Hz, 1mm a mplitude Switching Distance S a o 1mm Clo s e; S a r 10mm OpenMisalignment Between s witch a nd a ctu a tor, 2mm in a ny direction Switching Frequency 1.0Hz m a ximum Response Time (On –> Off)10m s m a x.Operating Time (Off –> On)150m sApproach Speed200mm/m to 1000mm/sBody MaterialD40ML-P_: Pl as ticD40ML-M_: Diec as t Met a lD40ML-SS _: 316 S t a inle ss S teel Actu a tor S e a l: S iliconeEnc a p s ul a tion: High Temper a ture Epoxy Operating Temperature Range–25 to 40°CAmbient Operating Humidityup to 90% a t 25 ~ 40°CEnclosure Protection IP67 (Pl as tic or Diec as t Met a l)IP69K (S t a inle ss s teel ver s ion s with flying le a d s )Cable Type PVC 8 core, 6mm outer di a meter Mounting Bolts 2 × M5 Tightening torque 1.0Nm Mounting Position AnyPower Supply 24VDC ±10% (s elv / pelv)Power ConsumptionUnlocked: 50mA m a x.Locked:- Medium Duty 325mA m a x. - He a vy Duty 500mA m a x.Holding ForceMedium Duty- S t a inle ss S teel: F1m a x (typic a l) 600N, F zh *1 450N - Pl as tic a nd Diec as t: F1m a x (typic a l) 900N, F zh 675N He a vy Duty- S t a inle ss S teel: F1m a x (typic a l) 950N, F zh 700N- Pl as tic a nd Diec as t: F1m a x (typic a l) 1500N, F zh 1150N *1A new te s t h as been introduced with the coefficient 1.3. A device with a s pecified m a ximum holding force (F zh ) of 500N need s to hold up a force te s t (F1m a x ) a t 650N.According to the s t a nd a rd the locking force F zh s hould be s t a ted for every gu a rd locking s witch.Max. Switched Current (Outputs)200mA (min. intern a l re s i s t a nce 8.5 Ohm s )Auxiliary Signal+24 VDC (Door Open)Characteristic Data according to EN ISO13849-1PLe: If both ch a nnel s a re u s ed in combin a tion with a S IL3/PLe control device C a tegory: C a t. 4MTTFd: 1100aDi a gno s tic Cover a ge DC: 99% (high)Number of oper a ting d a y s per ye a r: d op = 365d Number of oper a ting hour s per d a y: h op = 24h B10d: Not mech a nic a l p a rt s implemented Characteristic Data according to IEC62061 (used as a sub system)Sa fety Integrity Level: S IL3PFH (1/h): 4.77E-10 Corre s pond s to 4.8% of S IL3PFD: 4.18E-05 Corre s pond s to 4.2% of S IL3Proof Te s t Interv a l T 1: 20aInformation with regard to UL508U s e LVLC or Cl ass 2 s upply. Type 1 enclo s ure.Risk Time in accordance with EN 60947-5-3150m s (s witching off del a y a t remov a l of a ctu a tor)D40ML Series4Cable WiringTypical Operating Distance (Front Approach)Note:DO NOT u s e s witch a nd a ctu a tor as a gu a rd door stop.Solenoid Supply 24 VDCAuxSafety Output 2Safety Output 1External Supply 24 VDCNon-Contact RFID Locking Switch Wiring DiagramQuick Connect(CC)M12 8-way maleplugConductorColorsFunction Power Rating8Or a ngeApply Lock(24VDC ±10%)50mA M a x5BrownAuxili a ry S ign a l(Door Open/Clo s ed)+24VDC(200mA)4Yellow Sa fety Output 2200mA M a x6Green Sa fety Output 21White Sa fety Output 1200mA M a x7Bl a ck Sa fety Output 13Blue0VDC500mA M a x2Red+24VDC ±10%Misalignment mmDistance mmD40ML Series5Dimensions(Unit: mm)D40ML Medium Duty SwitchD40ML Heavy Duty SwitchInstallation:•In s t a ll a tion of a ll D40ML s erie s sa fety s witche s mu s t be in a ccord a nce with a ri s k ass e ss ment for the individu a l a pplic a tion.•The u s e of a sa fety rel a y i s required for monitoring RFID coded s witche s . The s e rel a y s monitor two redund a nt circuit s as per I S O13849-1 for up to PLe/C a tegory 4 protection.•D40ML s erie s s witche s a re de s igned to oper a te with mo s t du a l ch a nnel sa fety rel a y s to sa ti s fy EN60947-5-3.•M5 mounting bolt s mu s t be u s ed to mount the s witche s . Tightening torque for mounting bolt s to en s ure reli a ble fixing i s 1.0 Nm. Alw a y s mount on non-ferrou s m a teri a l s .•Do not mount a dj a cent s witche s or a ctu a tor s clo s er th a n 30mm.•To a chieve nomin a l holding force en s ure f a ce-to-f a ce a lignment of m a gnetic p a rt s .•After in s t a ll a tion a lw a y s check e a ch s witch function by opening a nd clo s ing e a ch gu a rd individu a lly in turn a nd en s uring th a t the Green LED on the s witch a nd the LED s on the sa fety rel a y a re illumin a ted when the s witch i s clo s ed a nd a re extingui s hed when the s witch i s open. Check th a t the m a chine s top s a nd c a nnot be re-s t a rted when e a ch s witch i s open.Maintenance/Safety Checks: Monthly: Check a lignment of a ctu a tor a nd look for s ign s of mech a nic a l d a m a ge to the s witch c as ing or c a ble s .The sa fety function s a nd mech a nic s mu s t be te s ted regul a rly. For a pplic a tion s where infrequent gu a rd a cce ss i s fore s ee a ble, the s y s tem mu s t h a ve a m a nu a l function te s t to detect a po ss ible a ccumul a tion of f a ult s . At le as t once per month for PLe C a t3/4 or once per ye a r for PLd C a t3 (I S O13849-1). Where po ss ible it i s recommended th a t the control s y s tem of the m a chine dem a nd s a nd monitor s the s e te s t s , a nd s top s or prevent s the m a chine from s t a rting if the te s t i s not done. (I S O14119). Check th a t the m a chine s top s a nd c a nnot be re-s t a rted when e a ch s witch i s open.NOTE: The sa fety output s will only clo s e when the a ctu a tor i s in pl a ce a nd the lock m a gnet i s energized. Forcing open of the lock will c a u s e the sa fety output s to open.IMPORTANT: The gu a rd holding h as no interlock function. The Ri s k A ss e ss ment for the p a rticul a r a pplic a tion s hould include the ri s k of s p a re a ctu a tor s . S p a re a ctu a tor s s hould not be re a dily a v a il a ble a nd mu s t be s ecurely controlled. Record a ny RFID code s as required by f a ctory rule s or with reference to a ny ri s k ass e ss ment for the p a rticul a r a pplic a tion a nd u s er loc a tion.Fixing Holes for M5 ScrewsACTUATORSWITCHFixing Holes for M5 Screws64648896Ø 5058.5060.50411R 32437523225445232626.50SWITCH Fixing Holes for M5 ScrewsFixing Holes for M5 ScrewsACTUATOR11579.5010575.50Ø 6544116666Ø 76Ø 805252443228.504338631D40ML Series6Wiring OptionsD40ML to G9SE-201(up to Safety PLe acc. EN ISO13849-1)D40ML to G9SE-201 - Series Connections (up to SafetyPLd acc. EN ISO 13849-1, maximum 20 switches)M: 3-phase motorTerms and Conditions AgreementRead and understand this catalog.Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments.Warranties.(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanshipfor a period of twelve months from the date of sale by Omron (or such other period expressed in writingby Omron). Omron disclaims all other warranties, express or implied.(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENT ATION, EXPRESS OR IMPLIED, ABOUTNON-INFRINGEMENT, MERCHANT ABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THEPRODUCTS. BUYER ACKNOWLEDGES THA T IT ALONE HAS DETERMINED THA T THE PRODUCTS WILLSUIT ABL Y MEET THE REQUIREMENTS OF THEIR INTENDED USE.Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) thenon-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above warranty.See /global/ or contact your Omron representative for published information.Limitation on Liability; Etc.OMRON COMP ANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENT AL, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.Suitability of Use.Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.NEVER USE THE PRODUCT FOR AN APPLICA TION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT ENSURING THA T THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THA T THE OMRON PRODUCT(S) IS PROPERL Y RA TED AND INST ALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.Programmable Products.Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence thereof.Performance Data.Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.Change in Specifications.Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to confirm actual specifications of purchased Product.Errors and Omissions.Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions.Authorized Di s tributor:In the interest of prod u ct improvement,specifications are s ub ject to change witho u t notice.Cat. No. F22E-EN-01C0421(0613)© OMRON Corporation 2013-2016 All Rights Reserved.OMRON Corporation Indu s trial Automation CompanyOMRON ELECTRONIC S LLC2895 Greenspoint Parkway, S u ite 200 Hoffman Estates, IL 60169 U.S.AT el: (1) 847-843-7900/Fax: (1) 847-843-7787Regional Headquarters OMRON EUROPE B.V.Wegalaan 67-69, 2132 JD Hoofddorp The NetherlandsTel: (31) 2356-81-300/Fax: (31) 2356-81-388 Contact: www.indu s trial.omron.euOMRON A S IA PACIFIC PTE. LTD.No. 438A Alexandra Road # 05-05/08 (Lo bb y 2), Alexandra T echnopark, Singapore 119967T el: (65) 6835-3011/Fax: (65) 6835-2711OMRON (CHINA) CO., LTD.Room 2211, Bank of China T ower, 200 Yin Cheng Zhong Road,P u Dong New Area, Shanghai, 200120, China T el: (86) 21-5037-2222/Fax: (86) 21-5037-2200。
UM604中文资料
UM600 SERIES 15 Watt DC-DC Converters ♦2:1 Input Range♦15W Isolated Output♦Efficiency to 84%♦Remote On/Off Control♦100 KHz Switching Frequency ♦Six-Sided ShieldSPECIFICATIONSAll specifications are typical at nominal line, full load and 25°C unless otherwise noted.INPUT SPECIFICATIONSInput Voltage Range,12V.………………..……..……..9-18V24V.…………………………...18-36V48V..…………………………..36-72V Input Filter…………………………………….…....Pi Network Reverse Voltage Protection1……….…..Internal Shunt DiodeUse External FuseOUTPUT SPECIFICATIONSVoltage Accuracy, Single Output ……………..…... ±1% max.Dual +Output .…………...….... ±1% max.-Output .………...……... ±3% max.Triple, 5V ……….…..………... ±2% max.±12V/15V ……..…..….... ±3% max. Voltage Balance, Dual Output at Full Load .…... ±1.0% max. Transient ResponseSingle,25%Step Load Change....................<500µsec. Dual,FL-1/2L,±1%Error Band.....................<500µsec. External Trim Adj. Range . (10)Ripple and Noise, 20MHz BW ……………. 10mV RMS max.75mV P-P max. Temperature Coefficient .…….………….….. ±0.02%°C max. Short Circuit Protection .…………………….…... Continuous. Overvoltage Protection, 5V ……………………………... 6.8V12V (15V)15V (18V)Line Regulation2, Single/Dual Output ………….. ±0.2% max.Triple Output .……….…..…….. ±1% max. Load Regulation3,Single/Dual Output .……….….. ±1% max.Triple Output ……………………. ±5% max.GENERAL SPECIFICATIONSEfficiency……………………….…………………..See Table Isolation Voltage.……………….……………..500VDC min. Isolation Resistance .………….…………..…. 108 Ohms min. Switching Frequency .………….…………………….. 100KHz Case Grounding.………………..Capacity Coupled to Input Operating Temperature RangeAmbient, None Derating ……..…………..... -25°C to +71°C Cooling .……….……………………….. Free Air Convection Storage Temperature Range .……………... -55°C to+105°C EMI/RFI ……………………..... Six-Sided Continuous Shield. Dimensions ………………………..... 2.56 * 3.0 * 0.83 inches(65 * 76.2 * 21.1mm) Case Material………………….... Black-Coated Copper withNon-Conductive Base Weight…………………..……………………………....... 180gNOTES:1.Determine the correct fuse size by calculating themaximum DC current drain at low line input, maximum load and then adding 20% to 25% to get the desired fuse size.2.Measured from high line to low line.3.Measured from full load to 1/4 full load.NOTES:1.Maximum total power from alloutputs is limited to 15 watts butno output should be allowed toexceed its maximum current.2.Minimum current on eachoutput is required to maintainspecified regulation.TRIPLE OUTPUT LOADING TABLE1Amperes Output Voltage2。
AD604中文文档
第一页模拟设备双倍的，超低噪音，可变的增益放大器。
AD604特点：在最大增益上的超低输入噪音：0.8nV/…两个独立的对数线性通道每通道的绝对增益范围：0 dB 到+48dB（前级放大器增益= +14dB），从+6 dB到+54 dB（前级放大增益= +20dB）增益精度是±1.0dB带宽：40MHZ（-3dB）。
300K欧输入电阻可变增益的缩放比例：20dB/V到40dB/V温度下的稳定增益和提供对单端信号可变单级增益控制能够直接驱动A/D转换器应用：超声和声呐时间增益控制高性能AGC系统信号测量产品描述：AD604是一个在超声应用中基于时间可变的增益控制，具有超低噪声，非常精确，双通道，对数线性的特点的可变增益放大器。
并且他将支持很多需求低噪声、宽带可变增益控制的应用。
为了容易使用，AD604的每一个通道都提供一个300 K欧的输入电阻和单级的增益控制。
用户决定增益范围，增益缩放比例和输出的dc 水平移位来更高的提高应用性能。
AD604的每一个通道都使用一个高性能的提供与输入有关的0.8nV/HZ(根号)噪音电压前置放大器。
AD604的不同输入指数级扩音器结构实现非常精确的对数线性响应。
每一个DSX-AMPs （指数级扩音器）包含一个可变的0 dB到48.36 dB衰减器和一个高速的固定增益放大器。
衰减器是基于一个七阶段的R-1.5R的梯形网络。
衰减器中间抽头点是6.908 dB和48.36 dB 对于梯形网络AD604的每一个独立的通道提供一个增益范围为48dB能够被通过编程优化在前置放大器反馈路径有单一外置的寄存器的前置放大器的应用。
AD604的对数增益响应能够被如下等式描述G (dB) = (GainScaling (dB/V) × VGN(V)) + (Preamp Gain (dB) – 19 dB)。
前置放大器增益在5到10 之间（+14 dB and +20 dB）提供全部的增益范围每个通道是0dB到+48 dB和+6dB 到+54dB。
ZZ-IO404D-RS485四路控制器说明书
ZZ-IO404D-RS485 四路控制器产品使用说明书目录一、产品特点 (3)二、产品功能 (3)三、产品选型 (3)四、主要参数 (3)五、接口说明 (4)六、接线说明 (5)1、RS485级联接线方式 (5)2、输出接线 (5)3、输入接线 (8)七、测试软件说明 (9)1、软件界面 (9)2、通讯测试 (9)八、参数及工作模式设置 (10)1、设备地址 (10)2、工作模式 (12)3、闪开闪断功能及设置 (13)九、开发资料说明 (14)1、通讯协议说明 (14)2、Modbus寄存器说明 (14)3、指令生成说明 (15)4、指令列表 (15)5、指令详解 (16)十、常见问题与解决方法 (19)十一、联系方式 (19)十二、质保售后 (19)十三、免责声明 (20)一、产品特点⚫DC7-30V；⚫继电器输出触点隔离；⚫通讯接口支持RS485；⚫通信波特率：2400,4800,9600,19200,38400（可以通过软件修改，默认9600）；⚫通信协议：支持标准modbus RTU协议；⚫可以设置0-255个设备地址，5位地址拨码开关可以设置1-31地址码，大于31的可以通过软件设置；⚫具有闪开、闪断功能，可以在指令里边带参数、操作继电器开一段时间自动关闭；二、产品功能⚫四路继电器控制；⚫四路开关量输入；⚫支持电脑软件手动控制；⚫支持本机非锁联动模式；⚫支持本机自锁联动模式；三、产品选型型号modbus RS232 RS485 USB WiFi 继电器输入 ZZ-IO404D-RS485 ●● 4 4四、主要参数参数说明触点容量10A/30VDC 10A/250VAC耐久性10万次数据接口RS485额定电压DC 7-30V电源指示1路红色LED指示输出指示4路红色LED指示温度范围工业级，-20℃～85℃尺寸115*95*41mm重量330g默认通讯格式9600,n,8,1波特率2400,4800,9600,19200,38400软件支持配套配置软件、控制软件；支持各家组态软件；支持Labview等五、接口说明引脚说明：序号引脚说明1 + 电源正极2 - 电源负极3 VIN 无源输入时VIN和COM短接用，具体查看输入接线图4 COM+ 无源输入时VIN和COM短接用，具体查看输入接线图5 IN1 第一路开关量输入6 IN2 第二路开关量输入7 IN3 第三路开关量输入8 IN4 第四路开关量输入9 COM- 无源输入时使用，具体查看输入接线图10 常开第一路继电器输出常开端11 公共端第一路继电器输出公共端12 常闭第一路继电器输出常闭端13 常开第二路继电器输出常开端14 公共端第二路继电器输出公共端15 常闭第二路继电器输出常闭端16 常开第三路继电器输出常开端17 公共端第三路继电器输出公共端18 常闭第三路继电器输出常闭端19 常开第四路继电器输出常开端20 公共端第四路继电器输出公共端21 常闭第四路继电器输出常闭端六、接线说明1、RS485级联接线方式电脑自带的串口一般是RS232，需要配232-485转换器（工业环境建议使用有源带隔离的转换器），转换后RS485为A、B两线，A接板上A端子，B接板上B端子，485屏蔽可以接GND。
SCI收录中国期刊国家一级期刊名录一览表
SCI收录中国期刊一览表JuneSnow-王从彦序英文刊名号9Acta Biochmicaet Biophysica Sinca Acta Botanica SinicaActa Ahimica SinicaActa Geologica Sinica-English EditionActa Mathematical Sinica-New SeriesActa Mechanica SinicaActa Mechanica Solida SiniaActa Pharmacologica SinicaActa Physica Sinica- 0verseas Edition中文刊名生物化学与生物物理学报植物学报化学学报地质学报（英文版）数学学报（新辑，英文版）力学学报（英文版）固体力学学报（英文版）中国药理学报物理学报（海外版）物理化学学报高分子学报代数集刊（英文版）ISSN------6818SCIsearchCDE789US1000-9515 891004-423X-05-Acta PhySico-Chimica Sinica11Acta Polymerica Sinica12AIgebra Colloquium13Applied Mathematics and Mechanics-English Edition应用数学和力学（英文版）SZ0253-482789生物医学与环境科学（英文版）4Biomedicaland Environmental Sciences15Chemical Journal of Chinese Universties-Chinese16Chemical Research in Chinese Universities17China Ocean Engineering18Chinese Annals of Mathematics Services B19Chinese Chemical Letters20ChineseJournalo of Chemical Engineering21ChineseJournalo of Chemistry22ChineseJournal of Polymer Science23Chinese Medical Journal24Chinese Physics Letters25Chinese Science Bulletin26Communications in Theoretical Physics27High Energy Physicsand Nuclear Physics28Journal of Computational Mathematics29Journal of Infrared and Millimeter Waves30Journal of Inorganic Materials31Journal of Iron and Steel Research Internatinal32Journal of Materials Science＆TechnOlogy高等学校化学学报高等学校化学研究（英文版）中国海洋工程（英文版）0890-548789数学年刊-B辑（英文版）中国化学快报（英文版）中国化学（英文版）高分子学报（英文版）中华医学杂志（英文版）中国物理快报（英文版）科学通报（英文版）理论物理通讯（英文版）高能物理与核物理计算数学学报（英文版）红外与毫米波学报无机材料学报材料科学技术（英文版）SZ-604C--US0256-307X- 65386 890253- 61--89中国化学工程学报（英文版）- 324X891005-0302国际钢铁研究学报（英文版）1006-706X稀上学报（英文版）33Journal of Rare EarthsJournal of Wuhan University of Technology-Mater Sci武汉工业大学学报（材料科学,34英）Ed35Progress in Biochemistry and Biophysics36Progress in natural Science生物化学与生物物理进展自然科学进展（英文版）US1002-0071 678937Rare Metal Materials and Engineering38ScienceinChinaA-Mathematics,Physics,Astronom稀有金属材料与工程1002-185X9789Series 中国科学-A辑（数学,物理,天1006-9283文学,英）3940Science in China Series C-Life Sciences41Science in China Series D-Earth Sciences42Science in China Seried E-Technological Sciences中国科学- B辑（化学，英）16789中国科学- c辑（生命科学，英）1006n中国科学- D辑（地球科学，英）1006-9313中国科学-E辑（技术科学，英）3Transactionsof Nonferrous Metals Society of China中国有色金属学报（英文版）中国教育与社会？44Chinese Educationand SocietyUS1061-1932 78945Chinese Law and Government46Chinese Literature47Chinese Sociology and Anthropology48Chinese Studies in Philosophy49Chinese Studies in History50Contemporary ChineseThought法律与政府？中国社会学与人类学中国哲学研究中国历史研究当代思潮（中文版）US0009-460989FOOO9-4617 89US0009-4625 789US0023-8627 7 9US097-146789国家一级期刊名录JuneSnow-王从彦http://liuyuexue.any国家一级刊物目录是根据国务院学位委员会办公室，原国家教委研究生工作办公室确定的一级刊物。
康佳电视说明书
康佳电视说明书康佳电视说明书篇一:康佳电视说明康佳“T”系列彩电简介在201X年春天，康家集团多媒体事业部以科技创新为动力，运用最新的数字视频处理技术开发出新一代“高清”数字电视P3460T、P3409T、P2902T、P2906T等系列新产品，为提升康佳品牌形象作出了新的努力。
为了配合作好新产品的推广和技术服务工作，现将P3460T系列彩电的电路结构特点和检修参考数据介绍如下。
康佳P3460T彩电的电路结构特点简介康佳P3460T系列彩电的核心电路主要由大规模数字处理芯片构成，其中包含视频信号数字处理芯片U1(DPTV-3D/MV);伴音信号数字处理芯片N205(MSP3463G);微处理控制系统N601(SDA555XFL);N602(AT24C16);以及扫描及视频处理N301(SDA9380)等集成电路。
为了保持电路简洁，合理利用有效空间，本机采用主电路板与单元电路板相结合的方式组成整机电路。
本机的印刷电路板包含主信号处理板、电源扫描伴音功放输出板、视放输出板、速度调制输出板、AV输入板、遥控按键输入板。
还有三个单元电路板通过多脚双排插座与主信号板相连。
即以SDA555XEL为核心的微处理控制单元电路板，通过XS001(64脚双排插座)与主电路板相连。
以DPTV-3D/MV为核心的视频信号数字单元电路板，通过X002、X003与主信号板相连。
以SDA9380为核心的扫描视频信号输出单元电路板通过X004与主信号板相连，为了帮组快速判断电路故障点，下列P3460T总线流程图与电路框图康佳“T”系列彩电故障检修 T系列机故障检修实例1 机型P2903T 故障现象: 伴音平衡失控分析与检修:开机后伴音平衡不起作用，拔掉XS202或XS203任一插排，另一声道也无伴音，用另一性能完好的TV信号处理板试机故障依旧，故障应在功放部分，检查功放外围元件无损坏，这时发现扬声器负极的两根黑线连接不正常，应连接左声道的黑线连到了右声道的负极，连接右声道的黑线连接在左声道的负极，将两根线正确连接后开机故障排除。
德威仪表 Series 604A 差压传感器操作指南说明书
13/321/4[11.91]The Dwyer Series 604A Differential Pressure Transmitterconverts air or compatible gas pressure into a standard 4-20 mAoutput signal for pressure ranges from 0-0.4” up to 0-120˝ w.c.(0-2.54 mm up to 0-304.9 mm w.c.). Each of these modelsoverlap in range so that any range within these limits can beachieved by adjustment of the span and zero controls. Versatilecircuit design enables use in 2, 3 or 4-wire current loops.Positive, negative or differential pressures can be measuredwithin an accuracy of ±2% of span. The Series 604A uses anisolated piezoresistive pressure sensor to produce a resistancechange across a wheatstone bridge. The signal is conditionedand converted into a 4-20 mA output signal.For applications requiring direct pressure or percent of full spanreadings, the optional A-701 digital readout makes an idealcompanion device. It provides a bright .6˝ (15.3 mm) high, 3-1/2digit, LED display while also supplying power to the Series 604ATransmitter.SPECIFICATIONSService: Air and non-combustible, compatible gases.Wetted Materials: Consult factory.Accuracy: ±2% of full span output (Includes linearity,hysteresis and repeatability).Stability:±1% F.S./yr.Temperature Limits: 0 to 140°F (-17.8 to 60°C).Compensated Temperature Limits:20 to 120°F (-6.67 to48.9°C).Pressure Limits: 2 psig for models 604A-0, 604A-1; 11 psigfor models 604A-2, 604A-3.Thermal Effect: ±0.025% F.S./°F (0.045% F.S./°C).Power Requirements: 10-35 VDC (2-wire*).Output Signal: 4 to 20 mA.Zero and Span Adjustments: Internally accessiblePotentiometers.Loop Resistance: DC; 0-1250 ohms maximum.Current Consumption: DC; 38 mA maximum.Electrical Connections: Terminal block.Process Connections: Barbed, for 3/16˝ (4.76 mm) I.D.tubing.Mounting Orientation: Diaphragm in vertical position. Consultfactory for other position orientations.Weight: 5.6 oz (159 g).Agency Approvals:CE.Model604A-0604A-1604A-2604A-3As Stocked0-0.5 (0-12.7 mm)0-2.0 (0-50.8 mm)0-10 (0-254 mm)0-50 (0-127 cm)Min. Range0-0.4 (0-10.1 mm)0-0.5 (0-12.7 mm)0-2.0 (0-50.8 mm)0-15 (0-381 mm)Max.Range0-1.0 (0-25.4 mm)0-4.0 (0-101.6 mm)0-20 (0-50.8 cm)0-120 (0-305 cm)RANGES IN INCHES OF WATERPatent No. 301,018INSTALLATIONLOCATION: Select a location where temperature of the unit will be between 20°F and 120°F (7°C and 49°C). Distance from the receiver is limited only by total loop resistance. See “Electrical Connections.” The tubing feeding pressure to the instrument can be run practically any length required, but long lengths will slightly increase response time. Avoid surfaces with excessive vibration.POSITION: The Model 604A-0 must be mounted and operated only in a vertical position due to its sensitivity to gravitational forces. Higher range models will perform properly at other angles, but they must be spanned and zeroed in the position in which they will be used. The minimum and maximum ranges possible may shift depending upon degree of tilt.PRESSURE CON N ECTION S: Two barbed connectors are provided for use with 3/16˝ I.D. vinyl or rubber tubing. Attach tubing from positive pressure source to HI port. Leave LO port vented. For negative (vacuum) pressure, connect to LO port and leave HI port vented. For differential pressures, connect the higher to HI port and lower to LO port.MOUNTING: Attach the Series 604A Transmitter to a vertical surface using the #10 x 1˝ pan head sheet metal screws provided. Mounting holes are located in upper left and lower right corners of case.ELECTRICAL CONNECTIONSCAUTION: DO NOT EXCEED SPECIFIED SUPPLY VOLTAGE RATIN GS. PERMAN EN T DAMAGE N OT COVERED BY WARRAN TY WILL RESULT. THIS UN IT IS N OT DESIGN ED FOR 120 VAC or 240 VAC LINE OPERATION.Electrical connections to the Series 604A Transmitter are made inside the enclosure on the left side of the unit. Remove the cover, feed stripped and tinned leads through the bottom and connect to terminal block screws marked 1,2,3 or 4. Refer to Figure B for locations of terminal block, span and zero adjust potentiometers.Wire Length - The maximum length of wire connecting transmitter and receiver is a function of wire size and receiver resistance. Wiring should not contribute more than 10% of receiver resistance to total loop resistance. For extremely long runs (over 1000 ft. [305 m]), choose receivers with higher resistances to minimize size and cost of connecting leads.Where wiring length is under 100 ft. (30.48 m), lead wire as small as 22 AWG can be used.2-Wire Operation - An external power supply delivering 13-35VDC with minimum current capability of 40 mA DC (per transmitter) must be used to power the control loop. See Fig. C for connection of the power supply, transmitter and receiver.Note the jumper between terminals 3 and 4. The range of appropriate receiver load resistance (R L ) for the DC power supply voltage available is expressed by the formula and graph in Fig. F. Shielded two wire cable is recommended for control loop wiring. If grounding is required use negative side of control loop after receiver. In Fig.C below, if power supply lead to terminal 1 is positive, ground should be connected to wiring at right of receiver. Otherwise, in 2 wire operation it is not necessary to observe polarity of control loop connections.3-Wire Operation - An external power supply delivering 13-35VDC with minimum current capability of 40 mA DC (per transmitter) is required. See Fig. D for connection of power supply, transmitter and receiver. The range of appropriate receiver load resistance (R L ) for the DC power supply available is expressed by the formula and graph in Fig. F. Shielded cable is recommended for control loop wiring. Do not employ a separate ground in 3 wire operation. Unit will not function properly and/or damage could result. Control loop polarity must be observed in the following respect. Although power supply terminals 1 and 2 are not polarized, the receiver must be connected between terminal 4 of transmitter and negative side of power supply.3-WIRE CONNECTIONVoltage Output - Series 604A Differential Pressure Transmitters can be easily adapted for receivers requiring 1-5 VDC or 2-10 VDC input. Insert a 249 OHM, 1/2watt(1-5 VDC) or 499 ohm (2-10 VDC) resistor in series with the current loop but in parallel with the receiver input. L ocate this resistor as close as possible to the input. Because resistor accuracy directly influences output signal accuracy, we recommend use of a precision ±0.1% tolerance resistor tominimize this effect. See Figs. H and J.SERIES 604A PRESSURE TRANSMITTERPOWER SUPPLY 13-35 VDC 18-26 VAC4-WIRE CONNECTION (1-5/2-10 VDC OUTPUT)Fig. HFig. J。
欧姆龙RFID
⑤本产品目录中述及的应用事例仅作为参考之用，实际使用时，应事前确认设备·装置的功能以及安全性等 之后，再进行使用。
Con la presente Omron dichiara che la RFID Sistema, V680-HS52Serie, V680-HS63 Serie, V680-HS65 Serie, V680-HA63B Serie sono conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
6.价格
本手册中记载的标准价格仅供参考。此价格中不包含消费税。
7.适合范围
上述内容仅限日本国内地区的交易。 其他地区和海外的交易及使用注意事项请与当地销售网点的人员咨询。
RFID 系统
操作手册 3
前言
前言
安全注意事项
●安全使用警告标志 本说明书中的以下标志用于指出在确保安全使用 V680-HS63/-HS52/-HS65/-HA63B 和 V680-D2KF67/-D2KF67M/D2KF52M/-D8KF68/-D32KF68系统时，必须警惕的地方。这些注意事项中包含重要的安全信息，请务必阅读。
前言
放大器 V680-HA63B
天线
V680-HS52 V680-HS63 V680-HS65
英语 芬兰语 荷兰语 法语 瑞典语 丹麦语 德语 希腊语 意大利语 西班牙语 葡萄牙语 罗马尼亚语
IXDD604SIA;IXDI604PI;IXDF604SIA;IXDN604SIA;IXDN604SI;中文规格书,Datasheet资料
IXD_604
Applications
• • • • • • Efficient Power MOSFET and IGBT Switching Switch Mode Power Supplies Motor Controls DC to DC Converters Class-D Switching Amplifiers Pulse Transformer Driver
INTEGRATED CIRCUITS DIVISION
Features
• 4A Peak Source/Sink Drive Current • Wide Operating Voltage Range: 4.5V to 35V • -40°C to +125°C Extended Operating Temperature Range • Logic Input Withstands Negative Swing of up to 5V • Matched Rise and Fall Times • Low Propagation Delay Time • Low, 10A Supply Current • Low Output Impedance
Packing Method
Tape & Reel Tube Tube Tape & Reel Tube Tape & Reel Tube Tube Tape & Reel Tube Tape & Reel Tube Tube Tape & Reel Tube Tape & Reel Tube Tube Tape & Reel Tube Tape & Reel
RoHS
2002/95/EC
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
Notes : ( 1 ) The type number listed have a standard tolerance on the nominal zener voltage of ± 10%, altered the fourth number of type from " 0 " for ± 10% tolerance to be " 5 " for ± 5.0% tolerance. ( 2 ) " SZ " will be omitted in marking on the diode.
Symbol
PD VF TJ Ts
Value
5.0 1.2 - 55 to + 150 - 55 to + 150
Unit
W V °C °C
Note : (1) T L = Lead temperature at 5.0 mm2 ( 0.013 mm thick ) copper land areas.
SZ603D SZ603G SZ603J SZ604D SZ604H SZ605B SZ605G SZ606A SZ606C SZ606I SZ607F SZ608C SZ608H SZ609B SZ6010 SZ6011 SZ6012 SZ6013 SZ6014 SZ6015 SZ6016 SZ6017 SZ6018 SZ6019 SZ6020 SZ6022 SZ6024 SZ6025 SZ6027 SZ6028 SZ6030 SZ6033 SZ6036 SZ6039 SZ6043 SZ6047 SZ6051 SZ6056 SZ6060 SZ6062 SZ6068 SZ6075 SZ6082 SZ6087 SZ6091 SZ60B0 SZ60B1 SZ60B2 SZ60B3 SZ60B4 SZ60B5 SZ60B6 SZ60B7 SZ60B8 SZ60B9 SZ60D0 3.3 3.6 3.9 4.3 4.7 5.1 5.6 6.0 6.2 6.8 7.5 8.2 8.7 9.1 10 11 12 13 14 15 16 17 18 19 20 22 24 25 27 28 30 33 36 39 43 47 51 56 60 62 68 75 82 87 91 100 110 120 130 140 150 160 170 180 190 200 380 350 320 290 260 240 220 200 200 175 175 150 150 150 125 125 100 100 100 75 75 70 65 65 65 50 50 50 50 50 40 40 30 30 30 25 25 20 20 20 20 20 15 15 15 12 12 10 10 8.0 8.0 8.0 8.0 5.0 5.0 5.0 3.0 2.5 2.0 2.0 2.0 1.5 1.0 1.0 1.0 1.0 1.5 1.5 2.0 2.0 2.0 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 3.0 3.0 3.5 3.5 4.0 5.0 6.0 8.0 10 11 14 20 25 27 35 40 42 44 45 65 75 75 90 125 170 190 230 330 350 380 430 450 480 400 500 500 500 450 400 400 300 200 200 200 200 200 150 125 125 125 100 75 75 75 75 75 75 75 75 100 110 120 130 140 150 160 170 190 210 230 280 350 400 500 620 720 760 760 800 1000 1150 1250 1500 1500 1650 1750 1750 1850 1850
Dimensions in millimeter
MAXIMUM RATINGS
Rating at 25 °C ambient temperature unless otherwise specified
Rating
DC Power Dissipation at T L = 75 °C (Note1) Maximum Forward Voltage at I F = 1.0 A Junction Temperature Range Storage Temperature Range
IZK (mA)
1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
Maximum DC Zener Current IZM (mA)
1440 1320 1220 1100 1010 930 856 790 765 700 630 580 545 520 475 430 395 365 340 315 295 280 265 250 237 216 198 190 176 170 158 144 132 122 110 100 93.0 86.0 79.0 76.0 70.0 63.0 58.0 54.5 52.5 47.5 43.0 39.5 36.6 34.0 31.6 29.4 28.0 26.4 25.0 23.6
SURFACE MOUNT SILICON ZENER DIODES
SMB (DO-214AA)
4 .8 ± 0 .1 5
5 .4 ± 0 .15
1.1 ± 0 .3
2.0 ± 0.1 3.6 ± 0.1 5 2.3 ± 0.2
0.22 ± 0.07
MECHANICAL DATA
* * * * * * Case : SMB (DO-214AA) Molded plastic Epoxy : UL94V-O rate flame retardant Lead : Lead formed for Surface mount Polarity : Color band denotes cathode end Mounting position : Any Weight : 0.093 gram
Fig. 1 POWER TEMPERATURE DERATING CURVE PD, MAXIMUM DISSIPATION (WATTS)
5.0 4.0 3.0 2.0 1.0 0 0 25 50 75 100 125 150 175 5.0 mm2 ( 0.013 mm thick ) copper land areas.
Maximum Leakage Current IR @ V R (V) (µA)
300 150 150 150 150 150 150 150 150 150 150 150 150 150 150 50 2.0 1.0 1.0 1.0 1.0 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 1.0 1.0 1.0 1.0 1.0 1.0 2.0 3.0 4.0 4.9 5.4 5.9 6.3 6.6 7.2 8.0 8.6 9.4 10.1 10.8 11.5 12.2 13.0 13.7 14.4 15.8 17.3 18.0 19.4 20.1 21.6 23.8 25.9 28.1 31.0 33.8 36.7 40.3 43.0 44.6 49.0 54.0 59.0 63.0 65.5 72.0 79.2 86.4 93.2 101 108 115 122 130 137 144
T L, LEAD TEMPERATURE ( °C)
Page 1 of 2
Rev. 03 : March 25, 2005
元器件交易网
ELECTRICAL CHARACTERISTICS
Rating at 25 °C ambient temperature unless otherwise specified Nominal Zener Maximum Zener Voltage Impedance TYPE V Z @ IZT IZT Z ZT @ IZT ZZK @ IZK (V) (mA) (Ω) (Ω)
元器件交易网
SZ603D - SZ60D0
VZ : 3.3 - 200 Volts PD : 5 Watts
FEATURES :
* Complete Voltage Range 3.3 to 200 Volts * High peak reverse power dissipation * High reliability * Low leakage current * Pb / RoHS Free
Page 2 of 2
Rev. 03 : March 25, 2005