BADM 350Class4
CSESJ350 3
• Operating Manual • Warning Information• Parts ListCSESJ3503½ TonService JackMeets or exceeds ASME PALD-2005standards for performance & safety.Copyright © Professional Tool Products, 2009All rights reserveddeScripTionCSESJ350 service jack is a self-contained device designed for lifting, but not sustaining, a partial vehicular load. It consists of a frame with wheels and swivel casters supporting a mechanism that actuates a pivoting lift arm equipped with a saddle. It is designed for use by professional auto mechanics.***owner/uSer reSponSibiliTyThe owner and/or user must have an understanding of the manufacturer’s operating instructions and warnings before using this jack. Personnel involved in the use and operation of equipment shall be careful, competent, trained, and qualified in the safe operation of the equipment and its proper use when servicing motor vehicles and their components. Warning information should be emphasized and understood. If the operator is not fluent in English, the manufacturer’s instructions and warnings shall be read to and discussed with the operator in the operator’s native language by the purchaser/owner, making sure that the operator comprehends its contents.Owner and/or user must study and maintain for future reference the manufacturer’s instructions and pertinent warning information. Owner and/or user is responsible for keeping all warning labels and instruction manuals legible and intact. Replacement labels and literature are available from the manufacturer.inSpecTionVisual inspection should be made before each use of the jack, checking for leaking hydraulic fluid and damaged, loose or missing parts. Each jack must be inspected by a manufacturer’s repair facility immediately, if subjected to an abnormal load or shock. Any jack which appears to be damaged in any way, is found to be badly worn, or operates abnormally MUST BE REMOVED FROM SERVICE until necessary repairs are made by a manufacturer’s authorized repair facility. It is recommended that an annual inspection of the jack be made by a manufacturer’s authorized repair facility and that any defective parts, decals or warning labels be replaced with manufacturer’s specified parts. A list of authorized repair facilities is available from the manufacturer.OPERATIONIMPORTANT: Before attempting to raise a vehicle, check vehicle service manual for recommended lifting surfaces.1. To raise load: Close release valve tightly (by turning handle clockwise). DO NOT OVERTIGHTEN. Position jack under load so that saddle will contact load firmly and load is centered so it cannot slip. Operate jack handle until saddle approaches the load. Once again check to see that saddle is correctly positioned. Raise load to desired height. Place jack stands of appropriate capacity under the vehicle. DO NOT CRAWL UNDER VEHICLE WHILE LIFTING VEHICLE OR PLACING OR REMOVING JACK STANDS! Place jack stands at vehicle manufacturer's recommended lift areas that provide stable support for the raised vehicle.2. To lower load: Open release valve VERY SLOWLY (by turning handle counterclockwise). When release valve is opened, saddle and load will be lowered. Lower the vehicle slowly so as not to shock load the jack stands. Once repairs are completed, raise vehicle enough to remove jack stands. Lower vehicle very slowly.CAUTION: Keep hands or feet away from the hinge mechanism of the jack.hydraulic JacK mainTenanceIMPORTANT: Service jacks are designed for lifting purposes only; always support raised load with jack stands.regular mainTenance• Monthly or as necessary (depending on usage)1. Using a grease gun, add grease to grease fitting in the lift arm pivot shaft. (Use a multi-purpose NLGI type grease only.)2. Lubricate all linkages and pivot points. (Use white lithium spray grease only.)3. Remove handle; lubricate handle receptacle and handle end. (Use white lithium spray grease only.)4. Lubricate both rear casters, bearings and both front wheels. (Use white lithium spray grease only.)5. Tighten all accessible hardware.CSESJ350 Power Unit* Included in Seal Kit - RS35NSKOnly items identified by part number are available for purchase.RS35B20NPARTS BREAKDOWN - CSESJ350Item PartNo.No.DescriptionQty.1 RS35T01 Retaining Ring2 2 RS35T02 Washer 23 RS35B03 Front Wheel2 4 RS35B10 Rear Caster Ass'y.2 5 RS35T08 Hex Nut & Lock Washer2 6 RS35B11 Yoke Retaining Bolt & Washer 2 7 RS35T17 Handle Lever "B" 1 8 RS35T15 Handle Lever "A" 1 9 RS35009C Handle Bumper 1 10 RS35T13 Set Screw - Handle 1 11 RS35011C Handle Yoke 1 12 RS35B20N Power Unit Ass'y. 1 13 RS35T18 Universal Joint Ass'y.1 14 RS35B24 Block Linkage (incl. Split Pin, Ret. Rings) 1 15 RS35T12 Grease Fitting 1 16 RS35T04 Retaining Ring 2 17 RS35017 Saddle1 18 RS35018 Saddle Screw1 19 RS35019C Rubber Saddle Pad 1 20 RS35T19 Spring2Index PartNo.No.DescriptionQty.1 * Steel Ball 5 62 Large Pump Housing 13 * O-Ring 15 x 2.65 24 * Back-Up Washer 20 x 15.6 x 1.25 2 5 Big Pump Piston 16 Pump Spring 17 RSDC22N Dust Cover1 8 Washer1 9 RSRR27N Retaining Ring 201 10 RS35T18 Universal Joint Assembly1 11 * Steel Ball 6 1 12 * Brass Washer 2 13 Small Pump Housing 1 14 * O-Ring 10 x 2.65 2 15 * Back-Up Washer 15 x 10.6 x 1.25 2 16 Small Pump Piston 1 17 Pump Spring 1 18 RSDC15 Dust Cover1 19 Washer1 20 RSRR16 Retaining Ring 151 21 RS0FS37 Screw (incl. #22 o-ring)3 22 * O-Ring 7.1 x 1.8 3 23 Relief Valve Bolt 2 24 * Relief Valve Spring 2 25 * Plug 2 26 * Steel ball 4 1 27 Hydraulic Block 1 28 * Cylinder Seal 1 29 Cylinder 1 30 * O-Ring 31 x 4.6 1 31 * Gasket 1 32 Ram Bearing 1 33 Retaining Ring 30 1 34 Ram 1 35 Cylinder Nut 1 36 * O-Ring 29.6 x 3.5 1 37 * Gasket 1 38 Reservoir Tube 1 39 * Gasket 1proper STorageIt is recommended that this jack be stored in a dry location with all wheels touching the ground on a relatively level surface. TroubleShooTingImportant: Service jacks are self-contained devices used for lifting, but not sustaining, a partial vehicular load. In accordance with ASME-PALD standard, section 10-4.1.2 Load Sustaining Test: “A load not less than the rated capacity…shall not lower more than 1/8” (3.18mm) in the first minute, nor a total of .1875” (4.76mm) in 10 minutes.” Leak down within this range is considered normal operation and is NOT a warrantable defect.WARRANTY COVERAGECornwell Quality Tools Company (“Cornwell”) warrants against defects the hydraulic pump on this product for a period of TWO (2) YEARS from the date of original retail purchase. Cornwell Quality Tools Company (“Cornwell”) warrants against defects the balance of components on this product for a period of 90 days from the date of original retail purchase. Subject to the conditions and limitations set forth below, Cornwell will, at its option, either repair or replace any part of the product(s) that proves defective by reason of improper workmanship or materials.This warranty does not cover any damage to this product that results from accident, abuse, misuse, natural or personal disaster, or any unauthorized disassembly, repair, or modification. Repairs, disassembly and modification are only authorized to be made by Cornwell or a warranty service center approved by Cornwell. WARRANTY SERVICETo obtain warranty service, contact your Cornwell dealer.EXCLUSIONS AND LIMITATIONSTHIS WARRANTY AND THE REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, REMEDIES AND CONDITIONS, WHETHER ORAL OR WRITTEN, EXPRESS OR IMPLIED. CORNWELL SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, TO THE EXTENT PERMITTED BY APPLICABLE LAW, ANY WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IF CORNWELL CANNOT LAWFULLY DISCLAIM IMPLIED WARRANTIES UNDER THIS LIMITED WARRANTY, ALL SUCH IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. IN NO EVENT SHALL CORNWELL BE LIABLE TO THE PURCHASER OR TO THE USER OF A CORNWELL PRODUCT FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES BASED UPON BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE, TORT, OR ANY OTHER LEGAL THEORY. SUCH DAMAGES INCLUDE, WITHOUT LIMITATION, EXPENSES, LOST REVENUES, LOST SAVINGS, LOST PROFITS, OR ANY OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE PURCHASE, USE OR INABILITY TO USE THE CORNWELL PRODUCT.Some states do not allow the exclusion or limitation of incidental or consequential damages or exclusions or limitation on the duration of implied warranties or conditions, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary by state. Repair kits and replacement parts are available for many Cornwell products, regardless of whether or not the product is still covered by a warranty plan.Cornwell Quality Tools Company667 Seville Road • Wadsworth, OH 44281-1094。
色卡-RAL-德国色表标准
© 2000 by Günther Productions · Zöllnerstraße 38 · 51491 Overath
RAL 2002 Blutorange
RAL 2003 Pastellorange RAL 2004 Reinorange
RAL 2005 Leuchtorange RAL 2007 Leuchthellorange
RAL 1005 Honiggelb
RAL 1006 Maisgelb
RAL 1007 Narzissengelb RAL 1011 Braunbeige RAL 1012 Zitronengelb
CMYK 10 30 100 0 CMYK 5 30 90 0 CMYK 0 40 100 0 CMYK 30 40 70 0 CMYK 10 10 90 0
RAL 6005 Moosgrün
RAL 6006 Grauoliv
RAL 6007 Flaschengrün RAL 6008 Braungrün
RAL 6009 Tannengrün
CMYK 100 60 90 20 CMYK 90 80 90 20 CMYK 80 50 80 60 CMYK 70 50 70 80 CMYK 90 50 90 60
RAL 3027 Himbeerrot RAL 3031 Orientrot
RAL 4001 Rotlila
RAL 4002 Rotviolett
RAL 4003 Erikaviolett
CMYK 0 100 70 20 CMYK 20 100 90 20 CMYK 60 70 5 10 CMYK 40 100 90 5 CMYK 10 70 10 0
Classic 840-HR/841-GL
SM物料培训教材课件
较好，损耗小， 绝缘电阻高，但容量小，适用于高频电路；
铁电陶瓷电容容值较 大，但损耗和温度系数较大；适用于
低频电路(分SMD、DIP)。
B、铝电解电容：它是由铝圆筒做负 极，里面装有液体电解质， 插入一 片弯曲的铝带做正极制成，还需经电流电压处理， 处理使正极上形成 一层氧化膜做介质；其特点是容量大， 但漏电，稳定性差，有正负极性，适于电源滤波和低频电路 中；使用时正负极不可接反。
附4 某公司141系列承认书（例2）
SUCCESS
THANK YOU
2024/10/11
9、排阻
排阻是由若干个电阻组合，它有多个脚，有A型(RN) 和B型(RP)两种：A有一个公共端，其他各引脚与公共脚之 间的电阻为R：B型(RP)是相邻两脚的电阻为R。
由若干个电阻组合，它有多个脚，有A型（RN）和B型（RP）两 种；A型有一个公共脚，其他各引脚之间的电阻为R；B型（RP） 是相邻两脚的电阻为R。
再打印四位数字， 不但印刷成本高，而且肉眼 难于辨别，故有E96系 列的标示方法。
E96贴片电阻器的阻值通常用4位数字表示（3位基本值加一位乘 10的次方数）。这在3216（1206型）、2125（0805型）外形的电阻器上 尚可清晰地印刷与辨认。但在1608（0603）外形规格的电阻器上，再打 印4位数，不但印刷成本高而且肉眼难于辨认。
3 2.00 2.05 2.10 2.15 2.21 2.26 2.32 2.37 2.43 2.49
4 2.55 2.61 2.67 2.74 2.80 2.87 2.94 3.01 3.09 3.16
5 3.24 3.32 3.40 3.48 3.57 3.65 3.74 3.83 3.92 4.02
例如： 一颗电阻本体上印有473则表示电阻值为47X103欧=47千欧，100欧的 电阻本体上印字为101。
Omega SV-351 产品说明书
BVE83-SS
Control Input 120 Vac 120 Vac
120 Vac
Rating – –
–
FVL-400, visit /fvl400
BV81-SS, visit /bv80
Model No. Connection
SVP
¹⁄₈ NPT
SV-1200
¹⁄₈ or UNF
SV-1500
¹⁄₈ to 1¹⁄₂"
SV-1600A
¹⁄₄"
SV-1800A
¹⁄₄"
SV240/250
¹⁄₄"
SV4100/4300 ¹⁄₈ to ¹⁄₄"
SV-900
³⁄₈ to ³⁄₄"
Material1 Plastic PVDF or ¹⁄₄-28 BR Plastic Plastic BR BR PVC
J-3
SVPR, SVPL, and two SVP-1, visit /svp for more details.
SV-1600A, visit /sv1600
SV4100 visit /sv4100_sv4300
3 and 4-Way Solenoid Valves
BVP80
¹⁄₄ to 2"
BR or SS
BVPS80
¹⁄₄ to 2"
BR or SS
BVE80
¹⁄₄ to 2"
BR or SS
Type
Pneumatic Actuated Ball Valves
Pneumatic with Spring Return Actuated Ball Valves
克勒S-350 CD DVD玩家指南说明书
NoteSave all packing materials.If you need to ship the S-350 in the future, repack the unit in its original packaging to prevent shipping damage.S-350CD/DVD PlayerQUICK SETUP GUIDEGetting StartedThank you for your purchase of the Krell S-350. The S-350 CD/DVD Player is a modular design featuring reference caliber CD playback as well as an optional state-of-the-art video engine that provides stunning 1080p performance and video processing controls.The S-350 can be outfitted with different outputs to match the requirements of any high performance audio or home theater system.Configurations include:• S-350a - High performance CD player with balanced analog outputs • S-350av - Complete package including audio and video optionsPlease contact your authorized dealer, distributor, or Krell if you have any questions not addressed in the owner’s reference.Do not place the compact disc player where it could be exposed to dripping or splashing. Do not remove or bypass the ground pin on the end of the AC cord. This may cause radio frequency interference (RFI) to be introduced into your playback system.The ventilation grids on the top and bottom of the S-350 must be unobstructed at all times during operation. Do not place flammable material on top of or beneath the component.Turn off all systems' power before connecting the S-350 to any component. Make sure all cable terminations are of the highest quality, free from frayed ends, short circuits, or cold solder joints. Caution: Visible and invisible laser radiation. When the cover is open, avoid exposure to beam. This unit employs a laser. To prevent possible eye injury, only a qualified service person should remove the cover or attempt to service this device. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.THERE ARE NO USER-SERVICEABLE PARTS INSIDE ANY KRELL PRODUCT.1.Open the shipping box and remove the top layer of foam. You see these items:2.Grasp the underside of the foam end-caps that encase the S-350 and lift it straight out of the shipping box.3.Place the S-350 in a safe location and remove the protective plastic wrapping.Place the S-350 on a firm, level surface, away from excessive heat, humidity, andmoisture. The S-350 requires at least two inches (5 cm) of clearance on each side and at least two inches (5 cm) of clearance above and below the component to provide adequate ventilation. Installations inside cabinetry may need extra ventilation. Do not place the S-350 near hum sensitive components such as preamplifier phono stages or turntables. Although the S-350 is well shielded, placing it near these components could create interference and cause hum.The S-350 has superb regulation and does not require a dedicated AC circuit. Avoid connections through extension cords or multiple AC adapters. Highquality 15 amp grounded AC strips are acceptable. High quality AC line conditioners may be used if they are grounded and meet or exceed the unit's power supply rating of 50V A.WARNINGSKrell S-350 1UnpackingKrell Industries, LLC., 45 Connair Road,Orange, CT 06477-3650 USA TEL 203-799-9954, FAX 203-891-2028, E-MAIL *********************WEB SITE Connecting the S-350 to Your SystemFollow these steps to connect the S-350 to your system.1.Make sure all power sources and components are off before connecting inputs and outputs.2.Neatly organize the wiring between the S-350 and all system components.Separate AC wires from audio cables to prevent hum or other unwanted noises from being introduced into the system.3.Balanced outputs use three-pin XLR connectors. Single-ended outputs use RCA connectors. Maintain the correct left/right orientation of these outputs.4.T o play DVD discs (S-350av), connect desired video output to preamp/processor or display's video input. For use with apreamplifier/processor, connect digital audio output to digital audio input. 5.For two-channel compact disc playback only, connect the S-350 digital audio outputs to the D/A convertor or preamplifier/processor digital input orbalanced/single-ended analog audio outputs to the preamplifier balanced or single-ended analog audio inputs.6.Plug the AC power cord into the IEC power connector on the back panel.Then plug the AC power cord into the wall socket.Press the back panel power switch (35) labeled “1”. When the S-350 is initialized and in the stand-by mode, the red stand-by LED (2) on the front panelilluminates. Then press the power button on the front panel or the power key (1)on the remote control, to place the S-350 in the operational mode. When the blue power LED (2) illuminates, the S-350 is in the operational mode. 1. Insert disc into the slot2. Press the play button or key. The format type is visible in the front paneldisplay. The format type disappears and the front panel display reads TRACK 1 and the track time, as the disc begins playing.3.Adjust the volume level through your system volume control.4.Press the stop button or key to end disc playback.5.Press the play button or key (6) to begin playback again, from the first track.6.T o return the S-350 to the stand-by mode, press the power button or key (1).1. Do not install near any heat sources such as radiators, heat registers, stoves,or other apparatus (including amplifiers) that produce heat.2. Unplug this apparatus during lightning storms or when unused for long periods of time.3. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as a power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.4. The ventilation grids on the top of the apparatus and the space underneath it must be unobstructed at all times during operation. Do not place flammable material above or beneath the apparatus.5. Before making connections to the Evolution 505, ensure that the power is off and other components are in mute or stand-by mode. Make sure all cable terminations are of the highest quality, free from frayed ends, short circuits, or cold solder joints.Please contact Krell if you have questions not addressed in this guide.4 Krell S-350Licensing attributions:Manufactured under license from Dolby Laboratories.Dolby is a trademark of Dolby Laboratories.Manufactured under license under U.S. Patent #'s:5,451,942; 5,956,674; 5,974,380; 5,978,762;6,487,535 & other U.S. and worldwide patents issued & pending. DTS and the Symbol are registered trademarks & DTS Digital Surround and the DTS logos are trademarks of DTS, Inc. Product includes software. ©DTS, Inc. All Rights Reserved.Safety notices:This CLASS I apparatus must be connected to a MAINS socket outlet with a protective earthing connection.Operating the S-350This product complies with the EMC directive (89/336/EEC)and the low-voltage directive (73/23/EEC).1 S-350 1 S-350 remote control1 IEC connector (AC power) cord2 AAA batteries1 12 VDC (12 V trigger) cable1 T-10 T orx wrench 1 Quick Setup GuidePlacementAC POWER GUIDELINESP/N 310784v 1.0Krell recommends using balanced interconnect cables. Balancedinterconnect cables not only can minimize sonic loss but are also immune to induced noise, especially with installations using long cables. Balanced connections have 6dB more gain than single-endedconnections. When level matching is critical, keep this gain value in mind. Pin assignments for XLR connectors:Pin 1Shield (ground)Pin 2Non-inverting (hot) (0°)Pin 3Inverting (cold) (180°)NoteThe S-350 reads data discs. For example, if you prepare a CDR or DVR containing MP3 audio files,you can play the discs on the S-350. The following terminology appears in the front panel display, to help you navigate a data disc:ROOT = The beginning of the disc. F = A closed folder. TOP = An open folder.Press the enter button or key (11) to open a folder,move to the previous folder, or play a track.Press the up and down arrows or keys (10) to move between tracks in a folder.S-350MODELSERIALNUMBERFigure 1 The S-350 Front PanelFigure 3 The S-350 RemoteFigure 2 The S-350 Back PanelKrell ®is a registered trademark of Krell Industries, LLC, and is restricted for use by Krell Industries, LLC. its subsidiaries, and authorized agents. T osLink ®is a trademark of T oshiba Corporation. All other trademarks and trade names are registered to their respective companies.©2006 by Krell Industries, LLC, All rights reservedBack Panel2 Krell S-350Krell S-350 3。
红外距离传感器产品参考手册说明书
Laser type and high power narrow beam LED type BGS! Types with sensing distances of 100 mm and 300 mm Industry standard sizeHighly accurate height difference detection through low hysteresisRelatedproductsUniversal voltage typeBGS-2VP.384Higher accuracyBGS-HL,BGS-HDLP.310Transparent object detectionZ3R-QP.404 Selection tableFor the connector type, please purchase an optional JCN series connector cable.Options/AccessoriesConnector cablesL-shapedJCN-SCable length: 2 mJCN-5SCable length: 5 mJCN-10SCable length: 10 mJCN-LCable length: 2 mJCN-5LCable length: 5 mJCN-10LCable length: 10 mProtective mounting bracketUltra-durable 2 mm thick typeRust-resistant stainless steelS ensor is firmly secured using M3 Hexsocket head cap screwsT he bracket is also firmly secured usingM6 screwsLK-S01LK-S02 Meander detection of sheet materials Detection of multi-colored trays Detection of items on stainless steel lines Laser type application 1LED type application 1LED type application 2Straight326Laser, standard type BGS-ZL, BGS-Z seriesLaser types (Class 1) and high power narrow beam LED types are availableIdeal for height difference detection using low hysteresisIndustry standard sizeShort-range type hysteresis ≤ 3% (typical value)Mounting hole pitch: 25.4 mmLaser type (equipped with laser OFF input)High power narrow beam LED light source typeThe spot size of the laser type is ø1 mm at 100 mm (short-range type). Optimal for applications that in which small object detection and high repeat accuracy are required. It is also a Class 1 laser in which eye protection for workers is not necessary.*Classified as Class II in the US FDA standards.A short-range type with a sensing distance of 100 mm that achieves a low hysteresis of ≤ 3%. Demonstrates its strength in small height difference detection.* A mid-range type with a sensing distance of 300 mm that achieves a hysteresis of ≤ 5%.Features an industry standard pitch of 25.4 mm.Features a high power narrow beam LED light source . Because the spot light can be seen clearly even in brightfactories regardless of the LED light, confirmation of detection position is easier than for any other conventional model.*Compared to conventional models: Using LED light source.Laser typeH y s t e r e s i s (%)Sensing distance X (mm)High power narrow beam LED typeH y s t e r e s i s (%)Sensing distance X (mm)Laser, standard type BGS-ZL, BGS-Z seriesSpecifications*2. Classified as Class II in the US FDA standards.*3. D efined with center strength 1/e 2 (13.5%). There may be light leakage outside of the specified spot size. The sensor may be affected when there is a highly reflective object close to the target area.*4. Mounting bracket BEF-W100-A is included with the connector type.Specifications are subject to change without prior notice for product improvement purposes.Laser, standard type BGS-ZL, BGS-Z seriesI/O circuit diagramNPN output typePNP output typeConnector typeConnecting1 to 4 are connector pin No.NotesC onnect frame ground to the earth when the switching regulator is used for power supply. B ecause wiring sensor wires with high-voltage wires or power supply wires can result in malfunctions due to noise, which can cause damage, make sure to wire separately. Avoid using the transient state while the power is on (approx. 100 ms). T he connector direction is fixed as in the drawing to the right when you use L-shaped connector cable. Be aware that rotation is not possible.This product emits a Class 1 (II) visible laser beam that is compliant with IEC/JIS, FDA laser safety standards.Warning and explanation labels are affixed to the sides of the sensor.Laser type: BGS-ZL10 /BGS-ZL30Laser light precautions1 10 to 30 VDC2 Laser OFF input (laser type only)3 0 V4 Control output(Pin con guration)Sensor sideConnector cable sideWarningDo not look directly at the laser or intentionally shine the laser beam in another person’s eyes.Laser, standard type BGS-ZL, BGS-Z seriesDimensionsSensorConnector cable (optional)Cable typeConnector typeJCN-S, JCN-5S, JCN-10SJCN-L, JCN-5L, JCN-10L(Unit: mm)Light ON / Dark ONselection switchOutput indicator (orange)Light ON / Dark ONselection switchø4.7, 4-wire × 0.325 mm 2ø4.7, 4-wire × 0.325 mm 2Laser, standard type BGS-ZL, BGS-Z seriesConnector type (when using BEF-W100-A)(Unit: mm)Mounting bracketCable type (when using BEF-W100-B)Laser, standard type BGS-ZL, BGS-Z seriesTypical characteristic dataBGS-ZL10 Laser typeBGS-ZL30 Laser type③S e n s i n g a r e a Y (m m )④③Distance X (mm)④③D i s t a n c eY (m m )④③Sensing distance X (mm)④③Sensing distance (mm)④③Sensing distance (mm)④③H y s t e r e s i s (%)④③S e n s i n g d i s t a n c e (m m )④W h i t e p a p e rB l a c k p a p e rV e n e e b o a r d C a r d b o a r dB l a c k r u b b e rB l a c k s p o n g ③S e n s i n g a r e a Y (m m )④③D i s t a n c e Y(m m )④③H y s t e r e s i s (%)④Hysteresis51002003001015203025③S e n s i n g d i s t a n c e (m m )④③O p t i c a l p l a n e ④③Sensing distance X (mm)④③Sensing distance (mm)④③Distance X (mm)④③Sensing distance (mm)④White paperGray paper/white paper Black paper/white paperW h i t e p a p e rB l a c k p a p e rV e n e e b o a r dC a r d b o a r dB l a c k r u b b e rB l a c k s p o n gLaser, standard type BGS-ZL, BGS-Z seriesBGS-Z10 LED typeBGS-Z30 LED type③S e n s i n g d i s t a n c e (m m )④③S e n s i n g a r e a Y (m m )④③Distance X (mm)④③D i s t a n c e Y (m m )④③Sensing distance X (mm)④③O p t i c a l p l a n e ④③Sensing distance (mm)④③H y s t e r e s i s (%)④③Sensing distance (mm)④W h i t e p a p e rB l a c k p a p e rV e n e e b o a r dC a r d b o a rdB l a c k r u b b e rB l a c k s p o n g③S e n s i n gd i s t a n ce (m m )④③H y s t e r e s i s (%)④③Sensing distance (mm)④③S e n s i n g a r e a Y (m m )④③D i s t a n c e Y (m m )④③Sensing distanceX (mm)④③Distance X (mm)④1020304050③Sensing distance (mm)④③O p t i c a l p l a n e ④5W h i t e p a p e rB l a c k p a p e rV e n e e b o a r dC a r d b o a r dB l a c k r u b b e rB l a c k s p o n g。
A-不锈钢管 参数
$prp@SWAompartno$prp@Pipe Identifier $prp@SpecificationNominalDiameter@FilterSketchA标,DN15,Sch5s A标,DN15,Sch5s DN15,Sch5s Sch5s15 A标,DN20,Sch5s A标,DN20,Sch5s DN20,Sch5s Sch5s20 A标,DN25,Sch5s A标,DN25,Sch5s DN25,Sch5s Sch5s25 A标,DN32,Sch5s A标,DN32,Sch5s DN32,Sch5s Sch5s32 A标,DN40,Sch5s A标,DN40,Sch5s DN40,Sch5s Sch5s40 A标,DN50,Sch5s A标,DN50,Sch5s DN50,Sch5s Sch5s50 A标,DN65,Sch5s A标,DN65,Sch5s DN65,Sch5s Sch5s65 A标,DN80,Sch5s A标,DN80,Sch5s DN80,Sch5s Sch5s80 A标,DN90,Sch5s A标,DN90,Sch5s DN90,Sch5s Sch5s90 A标,DN100,Sch5s A标,DN100,Sch5s DN100,Sch5s Sch5s100 A标,DN125,Sch5s A标,DN125,Sch5s DN125,Sch5s Sch5s125 A标,DN150,Sch5s A标,DN150,Sch5s DN150,Sch5s Sch5s150 A标,DN200,Sch5s A标,DN200,Sch5s DN200,Sch5s Sch5s200 A标,DN250,Sch5s A标,DN250,Sch5s DN250,Sch5s Sch5s250 A标,DN300,Sch5s A标,DN300,Sch5s DN300,Sch5s Sch5s300 A标,DN350,Sch5s A标,DN350,Sch5s DN350,Sch5s Sch5s350 A标,DN400,Sch5s A标,DN400,Sch5s DN400,Sch5s Sch5s400 A标,DN450,Sch5s A标,DN450,Sch5s DN450,Sch5s Sch5s450 A标,DN500,Sch5s A标,DN500,Sch5s A标,DN500,Sch5s Sch5s500 A标,DN15,Sch10s A标,DN15,Sch10s DN15,Sch10s Sch10s15 A标,DN20,Sch10s A标,DN20,Sch10s DN20,Sch10s Sch10s20 A标,DN25,Sch10s A标,DN25,Sch10s DN25,Sch10s Sch10s25 A标,DN32,Sch10s A标,DN32,Sch10s DN32,Sch10s Sch10s32 A标,DN40,Sch10s A标,DN40,Sch10s DN40,Sch10s Sch10s40 A标,DN50,Sch10s A标,DN50,Sch10s DN50,Sch10s Sch10s50 A标,DN65,Sch10s A标,DN65,Sch10s DN65,Sch10s Sch10s65 A标,DN80,Sch10s A标,DN80,Sch10s DN80,Sch10s Sch10s80 A标,DN90,Sch10s A标,DN90,Sch10s DN90,Sch10s Sch10s90 A标,DN100,Sch10s A标,DN100,Sch10s DN100,Sch10s Sch10s100 A标,DN125,Sch10s A标,DN125,Sch10s DN125,Sch10s Sch10s125 A标,DN150,Sch10s A标,DN150,Sch10s DN150,Sch10s Sch10s150 A标,DN200,Sch10s A标,DN200,Sch10s DN200,Sch10s Sch10s200 A标,DN250,Sch10s A标,DN250,Sch10s DN250,Sch10s Sch10s250 A标,DN300,Sch10s A标,DN300,Sch10s DN300,Sch10s Sch10s300 A标,DN350,Sch10s A标,DN350,Sch10s DN350,Sch10s Sch10s350 A标,DN400,Sch10s A标,DN400,Sch10s DN400,Sch10s Sch10s400 A标,DN450,Sch10s A标,DN450,Sch10s DN450,Sch10s Sch10s450 A标,DN500,Sch10s A标,DN500,Sch10s DN500,Sch10s Sch10s500 A标,DN15,Sch20s A标,DN15,Sch20s DN15,Sch20s Sch20s15 A标,DN20,Sch20s A标,DN20,Sch20s DN20,Sch20s Sch20s20 A标,DN25,Sch20s A标,DN25,Sch20s DN25,Sch20s Sch20s25 A标,DN32,Sch20s A标,DN32,Sch20s DN32,Sch20s Sch20s32 A标,DN40,Sch20s A标,DN40,Sch20s DN40,Sch20s Sch20s40 A标,DN50,Sch20s A标,DN50,Sch20s DN50,Sch20s Sch20s50 A标,DN65,Sch20s A标,DN65,Sch20s DN65,Sch20s Sch20s65 A标,DN80,Sch20s A标,DN80,Sch20s DN80,Sch20s Sch20s80 A标,DN90,Sch20s A标,DN90,Sch20s DN90,Sch20s Sch20s90A标,DN100,Sch20s A标,DN100,Sch20s DN100,Sch20s Sch20s100 A标,DN125,Sch20s A标,DN125,Sch20s DN125,Sch20s Sch20s125 A标,DN150,Sch20s A标,DN150,Sch20s DN150,Sch20s Sch20s150 A标,DN200,Sch20s A标,DN200,Sch20s DN200,Sch20s Sch20s200 A标,DN250,Sch20s A标,DN250,Sch20s DN250,Sch20s Sch20s250 A标,DN300,Sch20s A标,DN300,Sch20s DN300,Sch20s Sch20s300 A标,DN350,Sch20s A标,DN350,Sch20s DN350,Sch20s Sch20s350 A标,DN400,Sch20s A标,DN400,Sch20s DN400,Sch20s Sch20s400 A标,DN450,Sch20s A标,DN450,Sch20s DN450,Sch20s Sch20s450 A标,DN500,Sch20s A标,DN500,Sch20s DN500,Sch20s Sch20s500OuterDiameter @PipeSketch $prp@WallThickness$属性@名称$属性@代号$属性@类型21.3 1.6DN15(φ21.3x1.6)GA/T 12459-2005 A标无缝不锈钢管26.9 1.6DN20(φ26.9x1.6)GA/T 12459-2005 A标无缝不锈钢管33.7 1.6DN25(φ33.7x1.6)GA/T 12459-2005 A标无缝不锈钢管42.4 1.6DN32(φ42.4x1.6)GA/T 12459-2005 A标无缝不锈钢管48.3 1.6DN40(φ48.3x1.6)GA/T 12459-2005 A标无缝不锈钢管60.3 1.6DN50(φ60.3x1.6)GA/T 12459-2005 A标无缝不锈钢管 76.1（73）2DN65(φ76.1（73）x2)GA/T 12459-2005 A标无缝不锈钢管88.92DN80(φ88.9x2)GA/T 12459-2005 A标无缝不锈钢管101.62DN90(φ101.6x2)GA/T 12459-2005 A标无缝不锈钢管114.32DN100(φ114.3x2)GA/T 12459-2005 A标无缝不锈钢管139.7 2.9DN125(φ139.7x2.9)GA/T 12459-2005 A标无缝不锈钢管168.3 2.9DN150(φ168.3x2.9)GA/T 12459-2005 A标无缝不锈钢管219.1 2.9DN200(φ219.1x2.9)GA/T 12459-2005 A标无缝不锈钢管273 3.6DN250(φ273x3.6)GA/T 12459-2005 A标无缝不锈钢管323.94DN300(φ323.9x4)GA/T 12459-2005 A标无缝不锈钢管355.64DN350(φ355.6x4)GA/T 12459-2005 A标无缝不锈钢管406.44DN400(φ406.4x4)GA/T 12459-2005 A标无缝不锈钢管4574DN450(φ457x4)GA/T 12459-2005 A标无缝不锈钢管5085DN500(φ508x5)GA/T 12459-2005 A标无缝不锈钢管21.3 2.1DN15(φ21.3x2.1)GA/T 12459-2005 A标无缝不锈钢管26.9 2.1DN20(φ26.9x2.1)GA/T 12459-2005 A标无缝不锈钢管33.7 2.8DN25(φ33.7x2.8)GA/T 12459-2005 A标无缝不锈钢管42.4 2.8DN32(φ42.4x2.8)GA/T 12459-2005 A标无缝不锈钢管48.3 2.8DN40(φ48.3x2.8)GA/T 12459-2005 A标无缝不锈钢管60.3 2.8DN50(φ60.3x2.8)GA/T 12459-2005 A标无缝不锈钢管 76.1（73）3DN65(φ76.1（73）x3)GA/T 12459-2005 A标无缝不锈钢管88.93DN80(φ88.9x3)GA/T 12459-2005 A标无缝不锈钢管101.63DN90(φ101.6x3)GA/T 12459-2005 A标无缝不锈钢管114.33DN100(φ114.3x3)GA/T 12459-2005 A标无缝不锈钢管139.7 3.4DN125(φ139.7x3.4)GA/T 12459-2005 A标无缝不锈钢管168.3 3.4DN150(φ168.3x3.4)GA/T 12459-2005 A标无缝不锈钢管219.14DN200(φ219.1x4)GA/T 12459-2005 A标无缝不锈钢管2734DN250(φ273x4)GA/T 12459-2005 A标无缝不锈钢管323.9 4.5DN300(φ323.9x4.5)GA/T 12459-2005 A标无缝不锈钢管355.65DN350(φ355.6x5)GA/T 12459-2005 A标无缝不锈钢管406.45DN400(φ406.4x5)GA/T 12459-2005 A标无缝不锈钢管4575DN450(φ457x5)GA/T 12459-2005 A标无缝不锈钢管508 5.5DN500(φ508x5.5)GA/T 12459-2005 A标无缝不锈钢管21.3 2.6DN15(φ21.3x2.6)GA/T 12459-2005 A标无缝不锈钢管26.9 2.6DN20(φ26.9x2.6)GA/T 12459-2005 A标无缝不锈钢管33.7 3.2DN25(φ33.7x3.2)GA/T 12459-2005 A标无缝不锈钢管42.4 3.2DN32(φ42.4x3.2)GA/T 12459-2005 A标无缝不锈钢管48.3 3.2DN40(φ48.3x3.2)GA/T 12459-2005 A标无缝不锈钢管60.3 3.6DN50(φ60.3x3.6)GA/T 12459-2005 A标无缝不锈钢管 76.1（73） 3.6DN65(φ76.1（73）x3.6)GA/T 12459-2005 A标无缝不锈钢管88.94DN80(φ88.9x4)GA/T 12459-2005 A标无缝不锈钢管101.64DN90(φ101.6x4)GA/T 12459-2005 A标无缝不锈钢管114.34DN100(φ114.3x4)GA/T 12459-2005 A标无缝不锈钢管139.75DN125(φ139.7x5)GA/T 12459-2005 A标无缝不锈钢管168.35DN150(φ168.3x5)GA/T 12459-2005 A标无缝不锈钢管219.1 6.3DN200(φ219.1x6.3)GA/T 12459-2005 A标无缝不锈钢管273 6.3DN250(φ273x6.3)GA/T 12459-2005 A标无缝不锈钢管323.9 6.3DN300(φ323.9x6.3)GA/T 12459-2005 A标无缝不锈钢管355.68DN350(φ355.6x8)GA/T 12459-2005 A标无缝不锈钢管406.48DN400(φ406.4x8)GA/T 12459-2005 A标无缝不锈钢管4578DN450(φ457x8)GA/T 12459-2005 A标无缝不锈钢管5088DN500(φ508x8)GA/T 12459-2005 A标无缝不锈钢管。
美国费纳德吉他产品说明书
PARTS LISTREF#DESCRIPTION PARTNUMBER 1BODY AM ELITE STRAT 3TSB7708470500 1BODY AM ELITE STRAT BLK7708471510 1BODY AM ELITE STRAT OLP7708471523 1BODY AM ELITE STRAT ACB7708472531 1BODY AM ELITE STRAT SBM7708471536 1BODY AM ELITE STRAT TBS7708472552 1BODY AM ELITE STRAT ABM7708471596 2NECK ASSY AM ELITE STRAT MAPLE7708464000 2NECK ASSY AM ELITE STRAT ROSEWOOD7708465000 3KEY LOCKING 1,2,3 POLISHED CHROME EA0073114000 4BUSHING KEY SET0058820049 5WASHER KEY SET 0053106049 6STRING TREE AM ELITE GUITAR CHROME7708381000 7SCREW SMA 2 X 9/16 FHP NICKEL0051621000 8NECK PLATE GUITAR DELUXE CHROME ALUM RH NO HOLE7708496000 9SCREW SMA 8 X 1-3/4 OHP NICKEL0015636049 10PICKGUARD AM ELITE STRAT SSS MG/BLK/MG 7708282000 10PICKGUARD AM ELITE STRAT SSS BROWN SHELL7708281000 11SCREW SMAB 4 X 1/2 ONP NICKEL0015578049 125-WAY SWITCH LEVER DISCRETE/COM0078776000 13SWITCH KNOB VINTAGE AGED WHITE0994938000 14SCREW M 6-32 X 5/8 RHP NICKEL0015800049 15CAPACITOR CD .01µF 600V 10% 1/2” DIAMETER0054504049 16RESISTOR 1/4W 470KΩ0066911000 17KNOB STRAT VOLUME S-1 SOFT OVERMOLD AGED WHITE7708070000 18SWITCH CAP S-1 STRAT AGED WHITE VOLUME0059266030 19SWITCH/POT S-1 250K .25 BUSHING W/NUT & WASHER0078777000 20WASHER LOCKING INTL 3/8 X .687 X .065 NICKEL0016436049 21NUT HEX 3/8-32 X 3/32 NICKEL0016352049 22CONTROL 250K 10% TAPER 0078779000 23KNOB STRAT TONE SOFT OVERMOLD AGED WHITE7708072000 24CONTROL 250K 10% TAPER NO-LOAD 0078780000 25CAPACITOR MPF RDL .022µF 250V 10%0024832000 26FERRULE JACK CHROME0991940000 27JACK PHONE OPEN CIRCUIT 110021956049*=NOT PICTURED IN DIAGRAMREF#DESCRIPTION PARTNUMBER 28BRIDGE ASSY STRAT AM DLX RH0077092000 28A BRIDGE PLATE ULTRA STRAT0036527000 28B BLOCK TREMOLO AM DLX STRAT RH 0077090000 28C BRIDGE SECTION ULTRA STRAT0990840100 28D SPRING BRIDGE 4 COIL 3/8 BLACK0019394049 28E SPRING-BRIDGE 3 COIL 1/4 BLACK0019395049 28F SCREW M 4-40x5/8 PHP BLK0017031049 28G SCREW HEIGHT ADJ. 1/40026779049 28H SCREW HEIGHT ADJ. 5/160026780049 28I SCREW M 8-32x3/8 FHP NI0019656049 28J SPRING CLIP, ULTRA0036531000 28K BUSHING NYL BLK .31OD .22ID x .87L0036614000 28L SCRW SET 10-32x3/16 HEX SKT FP BLXL0036615049 29PIVOT POST ASSY0093273000 30PICKUP ASSY STRAT DELUXE NOISELESS AGED WHITE BRIDGE7708558000 31COVER PICKUP STRAT DELUXE NOISELESS AGED WHITE7708561030 32SCREW SPECIAL M 4-40 X 13/16 #5 HEAD NICKEL0099474000 33TUBING SILICONE RUBBER CUT RED .5000063398000 34PICKUP ASSY STRAT DELUXE NOISELESS AGED WHITE MIDDLE7708557000 35PICKUP ASSY STRAT DELUXE NOISELESS AGED WHITE NECK7708428000 36STRAP BUTTON CHROME SET W/HDWR0990690000 37SCREW SMAB 5 X 1 OHP NICKEL0015610049 38FELT WASHERS BLACK V0994929000 38FELT WASHERS WHITE0994930000 39BACK COVER STRAT STD W/SLOT BROWN SHELL0991324000 39BACK COVER STRAT STD W/SLOT MG/BLK/MG0054029000 40SPRING CLAW TENSION NICKEL0010272100 41SPRING TREMOLO TENSION BLK 0018671049 *CASE MOLDED AM ELITE GUITAR7708547000 *TREMOLO ARM ULTRA DLX SNAPIN 0036534049 *WRENCH .050 HEX KEY SHORT ARM 0018531049 *WRENCH 3/32 HEX KEY SHORT ARM0018622000*=NOT PICTURED IN DIAGRAMPICKUP WIRING .01µF.022µFBLACK & WHITEWIRES FROM OUTPUTVOLUMES1 SWITCHBLACK WIRETO TREM CLAW NECK PICKUPMIDDLE PICKUPBRIDGE PICKUP5-WAY SWITCHRESISTOR 470KΩTONE 1 CONTROL TONE 2 CONTROLCAPACITOR.01µF CAPACITOR.022µFSWITCH AND CONTROL FUNCTION1910VOLUME8234765TONE124356TONE132154801978769212. BRIDGE PICKUP IN PARALLEL WITH NECK & MIDDLE PICKUPS IN SERIES.1. NECK PICKUP IN PARALLEL WITH MIDDLE & BRIDGE PICKUPS IN SERIES.MASTER VOL.S-1 SWTICHTONE 1TONE 25-WAY SWTICHNECK PICKUP (A)MID PICKUP (B)BRIDGE PICKUP (C)2345PICKUP IS OFFPICKUP IS ON 1DIMINISHED VOLUMETONE CONTROLS-1 SWITCH ON (DOWN POSITION)51432T1 ONLYT2 ONLYT1 & T2T2 ONLYT2 ONLY(UP POSITION)S-1 SWITCH OFF SELECTOR POSITION5 WAY TONE CONTROL51432T1 ONLY T2 ONLY T2 ONLYMIDDLE PU (B)BRIDGE PU (C)NECK PU (A)SELECTOR POSITION5 WAY 101897L U V OE M 101897L U V OE M COMBINED PICKUPS ARE IN PARALLELCOMBINED PICKUPS ARE IN SERIES T1 & T2T2 ONLY AS SHOWN ADDITIONAL COMMENTPARALLELSERIESMIDDLE PU (B)BRIDGE PU (C)NECK PU (A)SERIESPARALLEL。
永宏PLC使用手册
第 4 章：安装须知
4.1 安装环境 ................................................................................................... H4-1 4.2 PLC 安装的注意事项 ............................................................................... H4-1
1.7.12 通讯板(CB) ........................................................................................... H1-17 1.8 机型外观尺寸图 ........................................................................................ H1-18
7.3.1 继电器单端共点输出电路结构及其接线 ................................................ H7-3 7.3.2 晶体管单端共点 SINK 及 SRCE 输出电路结构及其接线 ....................... H7-4 7.3.3 晶闸管(TRIAC)单端共点输出电路结构及其接线 ................................... H7-5 7.4 晶体管单端共点输出电路反应速率的提升(仅高速和中速) .................. H7-5 7.5 数字量输出电路的输出组件保护及噪声抑制 ........................................ H7-6 7.5.1 继电器接点的保护与噪声抑制............................................................... H7-6 7.5.2 晶体管的保护与噪声维抑制 .................................................................. H7-7
MP-350 快速入门指南说明书
■ Read this guide and the separate “IMPORTANT SAFEGUARD” carefully before using the projector.■ This guide describes the basic operation of the projector taking for example of the connection to a computer. Refer to the instruction manual of the BOXi for any other operations and detailed information.©2012 Copyright ELMO Co., Ltd. All rights reserved .Any names, company names and product names referred to in this guide are trademarks or registered trademarks of the respective companies.MP-350QUICK START GUIDETABLE OF CONTENTSTABLE OF CONTENTS (2)1GETTING STARTED (3)Checking the package contents (3)Part names and functions (4)Preparing the remote control (5)2USING THE PROJECTOR (6)Installing the projector (6)Connecting to a device (7)Powering on (8)Detecting the input signal (9)Adjusting the projected image (10)Powering off (11)1GETTING STARTEDChecking the package contentsPart names and functions TOP/FRONT TOP/BACKRemote controlPreparing the remote controlA battery is pre-installed in the remote control at the time of shipment (with insulation sheet). Remove the insulation sheet before using the remote control for the first time.Volume ＋button －buttonMUTE buttonPower button2USING THE PROJECTORInstalling the projectorDecide the position to place the projector.The distance between the projector and the screen should be between 48cm (screen size: 25 inch) and 133cm (screen size: 68 inch).→ Refer to the instruction manual of the BOXi for detailed information.Connecting to a device1. Connect the power supply (AC adapter and power cord) to the projector.2. Connect the projector to the device such as a computer using RGB cable.BACKWhen using HDMI, use the HDMI terminal and HDMI cable (sold separately).Device (such as a computer) -Connecting using RGB terminalPowering on1. Pressbutton on the projector or the remote control.The opening screen appears.Detecting the input signal Wait until the projector automatically detects the input signal AUTO function to automatically detect the input signal is enabled at the time ofshipment. When the device is connected using RGB terminal or HDMI terminal, the input signal is detected automatically.Selecting the input signal from the menu1. Press button on the remote control or button on the control panel.「Input signal selection menu」appears.2. Select the input signal using buttons.3. Press button to execute.Input signal selection menuRemote controlControl panelAdjusting the projected imageFocusing the image1.Use the focus dial to focus the image.Correcting the keystone distortions1. Press + or - ofbutton on the remote control.「Keystone adjustment dialog 」 appears.2.Keystone adjustment dialogPowering off1.button on the projector or the remote control.2. button again.Power indicatorturns off.(Wireless LAN indicatorturns off at the same time.)Unplug the cable after the fan has stopped.When the warning indicator is lit or flashing, it indicates that some malfunction occurred to the projector. Refer to the instruction manual of the BOXi. CAUTIONRemote controlControl panel6X1SPJBC3(en) R0-Xex。
ANSI Class 300 气体控制阀门说明书
800-543-9038 866-805-7089 203-791-8396 •Bubble tight shut-off to ANSI Class 300 Standards • Long stem design allows for 2” insulation minimum• Valve Face-to-face dimensions comply with API 609 & MSS-SP-68•Designed to be installed between ASME/ANSI B16.5 Flanges •Completely assembled and tested, ready for installationApplicationThese valves are designed to meet the needs of HVAC and Commercial applications requiring positive shut-off for liquids at higher pressures and temperatures. Typical applications include chiller isolation, cooling tower isolation, change-over systems, large air handler coil control, bypass and process control applications. The large C v values provide for an economical control valve solution for larger fl ow applications.Dead End ServiceUtilizes larger retainer ring set screws to allow the valve to be placed at the end of the line without a down stream fl ange in either fl ow direction while still holding full pressure.MOD ON/OFF ValveSize C v 10°20°30°40°50°60°70°80°90°F650-300SHP 2”F665-300SHP 2½”F680-300SHP 3”F6100-300SHP 4”F6125-300SHP 5”F6150-300SHP 6”F6200-300SHP 8”F6250-300SHP 10”F6300-300SHP 12”F6350-300SHP 14”F6400-300SHP 16”F6 Series 2-Way, ANSI Class 300 Butterfl y Valve Reinforced Tefl on Seat, 316 Stainless DiscTechnical Data Servicechilled, hot water, 60% glycol,steam to 50 psi Flow characteristic modifi ed equal percentage, unidirectional Controllable fl ow range 82°Sizes2" to 24"Type of end fi tting ANSI 300 fl anges Materials Body Disc Seat ShaftGland seal Bushingscarbon steel full lug 316 stainless steel RPTFE17-4 PH stainless PTFEglass backed PTFEMedia temperature range -20°F to 400°F [-30°C to 204°C]Body pressure rating ANSI Class 300Close-off pressure 740 psiRangeability100:1 (for 30 deg to 70 deg range)Maximum velocity 32 FPS Leakagebubble tight2-way ValvesSuitable ActuatorsValve Nominal SizeNon Fail-SafeFail-SafeSpring ReturnElectronicC v90°C v 60°Inches ANSI 300 2-way 300300300102562F650-300SHP G M S e r i e sP R S e r i e sA F S e r i e sG K S e r i e s146802½F665-300SHP2281253F680-300SHP 4512484F6100-300SHP 7143925F6125-300SHP P K R11036076F6150-300SHP 206411358F6200-300SHPS Y (2 Y e a r W a r r a n t y )3517193410F6250-300SHP 4837266012F6300-300SHP 6857359214*F6350-300SHP102 1.50 6.10142639567799102146 2.208.8020375580110142146228 3.4014325787125171221228451 6.8027631141712483384374517141143100180271393536693714110317661542784196078271070110320643112428952078411351548200220643517532114928861336193426383411351748377329067712191838266036284692483768579039291416462481359248986530685792871325311230222933614865663488459287203-791-8396 F6 Series 2-Way, ANSI Class 300 Butterfl y ValveReinforced Tefl on Seat, 316 Stainless DiscDimension “A” does not include fl ange gaskets. (2 required per valve)Application Notes 1. V alves are rated at 725 psi differential pressure in the closed position @ 100°F media temperature.2. Valves are furnished with lugs tapped for use between ANSI Class 250/300 fl anges conforming to ANSI B16.5 Standards.3. 2-way assemblies are furnished assembled, calibrated and tested, ready for installation.4. Dimension “D” allows for actuator(s) removal without the need to remove the valve from the pipe.5. Weather shields are available, dimensional data furnished upon request.6. Dual actuated valves have actuators mounted on a single common shaft.7. Flange gaskets (2 required, not provided with valve) MUST be used between valve and ANSI fl ange.8. F lange bolts are not included with the valve. These are furnished by others.Maximum Dimensions (Inches)F650-300SHP 2”102 1.759.009.0019.50 5.0085/8-11 UNC 2*AF150Spring Return F665-300SHP 2½”146 1.889.009.0020.00 5.8883/4-10 UNC 150F680-300SHP 3”228 1.929.009.0020.50 6.6383/4-10 UNC 150F6100-300SHP 4”451 2.139.009.0021.007.8883/4-10 UNC 150F650-300SHP 2”1.759.009.0019.50 5.0085/8-11 UNC GK150Electronic Fail-Safe F665-300SHP 2½”1.889.009.0020.00 5.8883/4-10 UNC 150F680-300SHP 3”1.929.009.0020.50 6.6383/4-10 UNC 150F6100-300SHP 4”2.139.009.0021.007.8883/4-10 UNC 150F650-300SHP 2” 1.759.009.0019.50 5.0085/8-11 UNC 2*GK400F665-300SHP 2½” 1.889.009.0020.00 5.8883/4-10 UNC 400F680-300SHP 3” 1.929.009.0020.50 6.6383/4-10 UNC 400F650-300SHP 2”1.759.009.0019.50 5.0085/8-11 UNC GM285Non-Spring Return Electronic Fail-Safe (K)F665-300SHP 2½”1.889.009.0020.00 5.8883/4-10 UNC 285F680-300SHP 3”1.929.009.0020.50 6.6383/4-10 UNC 285F6100-300SHP 4”2.139.009.0021.007.8883/4-10 UNC 150F650-300SHP 2” 1.758.008.0022.25 4.7585/8-11 UNC PR/PKR 600F665-300SHP 2½” 1.888.008.0022.75 5.5083/4-10 UNC 600F680-300SHP 3” 1.928.008.0023.00 6.0083/4-10 UNC 600F6100-300SHP 4” 2.138.008.0023.757.5083/4-10 UNC 600F6125-300SHP 5”714 2.258.008.0024.259.2583/4-10 UNC PR/PK 400F6150-300SHP 6”1103 2.298.008.0024.7510.63123/4-10 UNC PR/PK 285F6200-300SHP 8”2064 2.8812.0012.0032.0013.00127/8-9 UNC SY4…600F6250-300SHP 10”3517 3.2512.0012.0033.0015.25161-8 UNC SY5…400SY7…600F6300-300SHP 12”4837 3.6212.0012.0035.0017.7516 1 1/8-8 UNC SY5…285SY7…600F6350-300SHP14”68574.6214.0014.0036.0020.25201 1/8-8 UNCSY7…400SY8…600ACBD102146228451102146228102146228451102146228451PRXUP-MFT-T Modulating, Non Fail-Safe, 24...240 V, NEMA4X with BACnetTechnical dataElectrical data Nominal voltage AC 24...240 V / DC 24...125 VNominal voltage frequency50/60 HzPower consumption in operation20 WPower consumption in rest position 6 WTransformer sizing20 VA @ AC/DC 24 V (class 2 power source), 23VA @ AC/DC 120 V, 52 VA @ AC 230 VAuxiliary switch 2 x SPDT, 3 A resistive (0.5 A inductive) @ AC250 V, 1 x 10° / 1 x 0...90° (default setting 85°)Switching capacity auxiliary switch 3 A resistive (0.5 A inductive) @ AC 250 VElectrical Connection Terminal blocks, (PE) Ground-ScrewOverload Protection electronic thoughout 0...90° rotationFunctional data Communicative control BACnet MS/TPModbus RTUMP-BusOperating range Y 2...10 VOperating range Y note 4...20 mAInput Impedance100 kΩ for 2...10 V (0.1 mA), 500 Ω for 4 (20)mA, 1500 Ω for On/OffOperating range Y variable Start point 0.5...30 VEnd point 2.5...32 VOptions positioning signal variable (VDC, on/off, floating point)Position feedback U 2...10 VPosition feedback U note Max. 0.5 mAPosition feedback U variable VDC variableDirection of motion motor reversible with appManual override7 mm hex crank, suppliedAngle of rotation90°Running Time (Motor)default 35 s, variable 30...120 sRunning time motor variable30...120 sNoise level, motor68 dB(A)Position indication integral pointerPassive sensor inputs2x (Pt1000, Ni1000, NTC10k2)Safety data Degree of protection IEC/EN IP66/67Degree of protection NEMA/UL NEMA 4XEnclosure UL Enclosure Type 4XAgency Listing cULus acc. to UL60730-1A/-2-14, CAN/CSAE60730-1:02, CE acc. to 2014/30/EU and2014/35/EU-22...122°F [-30...50°C]PRXUP-MFT-TApplicationOperationSafety dataStorage temperature -40...176°F [-40...80°C]Ambient humidity Max. 100% RH Servicingmaintenance-free Weight Weight13 lb [5.9 kg]MaterialsHousing materialDie cast aluminium and plastic casingProduct featuresPR Series valve actuators are designed with an integrated linkage and visual position indicators. For outdoor applications, the installed valve must be mounted with the actuator at or above horizontal. For indoor applications the actuator can be in any location including directly under the valve.The PR series actuator provides 90° of rotation and a visual indicator shows the position of the valve. The PR Series actuator uses a low power consumption brushless DC motor and is electronically protected against overload. A universal power supply is furnished to connect supply voltage in the range of AC 24...240 V and DC 24...125 V. Included is a smart heater with thermostat to eliminate condensation. Two auxiliary switches are provided; one set at 10° open and the other is field adjustable. Running time is field adjustable from 30...120 seconds by using the Near Field Communication (NFC) app and a smart phone.†Use 60°C/75°C copper wire size range 12...28 AWG, stranded or solid. Use flexible metal conduit. Push the listed conduit fitting device over the actuator’s cable to butt against the enclosure. Screw in conduit connector. Jacket the actuators input wiring with listed flexible conduit. Properly terminate the conduit in a suitable junction box. Rated impulse Voltage 4000 V. Type of action 1. Control pollution degree 3.AccessoriesGatewaysDescriptionType Gateway MP to BACnet MS/TP UK24BAC Gateway MP to LonWorks UK24LON Gateway MP to Modbus RTUUK24MOD Electrical accessoriesDescriptionType Service Tool, with ZIP-USB function, for programmable andcommunicative Belimo actuators, VAV controller and HVAC performance devicesZTH USMechanical accessoriesDescriptionType Hand crank for PR, PKR, PM ZG-HND PR Service toolsDescriptionTypeConnection cable 10 ft [3 m], A: RJ11 6/4 ZTH EU, B: 3-pin Weidmüller and supply connectionZK4-GEN Service Tool, with ZIP-USB function, for programmable and communicative Belimo actuators, VAV controller and HVAC performance devicesZTH USElectrical installationMeets cULus requirements without the need of an electrical ground connection.Universal Power Supply (UP) models can be supplied with 24 V up to 240 V.Disconnect power.Provide overload protection and disconnect as required.Two built-in auxiliary switches (2x SPDT), for end position indication, interlock control, fanstartup, etc.Only connect common to negative (-) leg of control circuits.Actuators may be controlled in parallel. Current draw and input impedance must be observed.PRXUP-MFT-TDuring installation, testing, servicing and troubleshooting of this product, it may be necessaryto work with live electrical components. Have a qualified licensed electrician or other individualwho has been properly trained in handling live electrical components perform these tasks.Failure to follow all electrical safety precautions when exposed to live electrical componentscould result in death or serious injury.Wiring diagramsOn/OffOn/OffBACnetModulatingPRXUP-MFT-T Floating PointTemperature Sensors Auxiliary SwitchesDimensionsDimensional drawings。
平板电脑MID整机成品检验标准
平板电脑MID整机成品检验标准一、目的：制定平板电脑成品检验标准，指导生产检验及成品出货检验，使QA在检验及判定时有据可依，使产品质量符合客户要求。
二、适用范围：本标准适用于QA对MID产品的验收。
三、名词解释和定义3.1、微处理器：由一个或多个处理器及其内部存储器组成的一种功能单元，其元件小型化到一个或几个集成电路。
3.2、硬件系统：以CPU为核心，包括RAM、ROM、I/O接口电路以及实体内配接的外围设备、电源或扩充单元等构成的硬件设备的总成；3.3致命缺陷：（Critical）危及人生安全，易招致不安全因素的项目以及导致其基本功能失效的项目。
3.4严重缺陷：（Major）不会危及人生安全，但可能导致功能失误或降低原有使用功能的项目。
3.5次要缺陷：（Minor）单位产品的一般性质量特征不符合规定或单位产品的质量特性轻微不符合规定，对产品的使用性能没有影响或只有轻微影响的项目。
四、抽样方案：1、抽样水准：AQL：MIL-STD-105EII级水准，CR=0MA=1.0MI=2.52、缺陷定义：CR：致命缺陷（影响用户生命、财产安全的缺陷）MA：主要缺陷（影响客户正常购买使用的缺陷）MI：一般缺陷（存在一定缺陷但不影响用户购买使用的外观缺陷）3、抽样数量：每100个为一个抽检计量单位，新机种、新物料第一批量产全检，每批订单清尾（每个订单的最后100台）需全检。
五、测试条件及工具a、工具：电脑、TF卡、鼠标、3G模块、耳机、充电器、U盘、塞规b、距离：目视与被测物距离35CM（±5CM）c、时间：每次检验目视与光源成45度，上下左右转动15度d、光线：正常荧光灯40W（光照强度：700-1000LUX）光源具被测物1-1.2M六、检查项目1、包装检查：未开箱前确认包装箱是否有破损，潮湿或者脏污现象，外箱标贴粘贴的方向、位置应正确，内容应符合客户的要求，不允许有粘贴二层现象，开箱后确认附件是否齐全及错放，包装彩盒应完好，主机摆放位置应正确，2、外观检查：2.1、检查步骤：（检验顺序正面-左右面-上下面-底面）a、外观不应有划伤、碰伤、掉漆、脏污、缩水、变形等不良b、文字、LOGO、功能丝印应完整、正确、清晰、无倾斜、偏移、模糊等不良c、面壳、中框、底壳、TP间的配合应完好，不能有缝隙、短差、TP翘等不良d、螺钉应无生锈、松动、脱落、滑牙、用错等不良e、接插口不应有明显变形、氧化、偏位、凸凹等不良f、同一面上颜色应均匀一致、无色差g、显示屏内应无杂物，水印等不良h、按键手感应良好、不能有凸凹不良，丝印应正确，摄像头不能有偏、陷、歪等不良2.2、检查标准及判定标准详见附表二3、功能检测3.1、检测步骤：a、按开机键开机，开机画面显示是否正常，开机LOGO是否正确，开机指示灯是否亮起，指示灯的颜色是否正确；b、进入系统是否正常，有无不进系统和进入时间长等不良，待机桌面及桌面文件是否符合客户要求；c、触摸测试：在触摸屏上、下、左、右、四角、中心触摸应有效，要求反应正常，不能有触摸不灵等不良d、显示屏测试：用红、绿、白、黑色画面检测彩点、亮点、暗点、漏光、透光等不良e、音乐、电影、喇叭测试：用不同格式的媒体文件进行播放，应播放正常，不应有咔音、显示花屏，内置喇叭声音应正常，不能有无声、单音、杂音等不良，同时将耳机插入耳机口，耳机声音应正常，不能有无声、杂音、单音等不良f、按键测试：整机所有的按键都应与丝印的功能相对应，不能有功能错乱、无功能、功能不灵等不良g、录音测试：进入录音界面，并点击开始录音（录音时间应在10秒钟以上），然后录音播放，应能清晰的听到录音的声音，不应有无声、杂音、破音等不良h、重力感应测试：将机器90度的旋转确认画面是否随机器的旋转而旋转i、摄像头测试：进入照相画面，画面应清晰，点击照相进行拍照，照片播放图像应无斑点、模糊、花屏、照片不能保存等不良，再点击摄像，摄像播放应能清晰的听到声音，图像应清晰，不能有花屏、模糊等不良j、USB口测试：分别用鼠标、U盘对USB接口进行连接，功能应正常，MimiUSB接口连接电脑，是否能连接，USBHOST接口接OTG线连接是否能识别，插拔设备时是否有阻碍等不良k、充电口测试：接通带电的充电器，是否连接充电正常，指示灯应正常亮起l、HDMI测试：连接HDMI转接线，确认显示是否显示正常，是否切换正常，分辨率是否正常，不应有花屏，显示不良等现象m、WIFI测试：打开WIFI，并自动搜索到无线网络设备化，且能正常连接，查看信号的强度（有必要时可安装WIFI分析仪查看WIFI的信号强度）和显示正确的IP地址，打开网页能自动进入并正确显示网页内容，网页放大、缩小能正常放大和缩小n、蓝牙测试（带蓝牙功能）：测试时需打开蓝牙，然后需点击蓝牙搜索，对蓝牙设备进行连接，连接后需能正常使用o、APK安装测试：APK文件是否能识别及安装，APK文件是否能正常删除p、3G测试（带3G功能）：机器在断电的状态插入已开通上网权限的SIM卡（或者外挂3G模块及卡），然后再开机，打开网络项的移动网络，将数据漫游及内置模块的电源打开，此时机器应能自动搜索到3G并能正常连接，连接后应能正常打开网页3.2、检查标准及判定标准详见附表二4、可靠性试验4.1试验的条件：a、更换了关键的元器件或供应商；b、新产品试产；c、第一次量产机器；d、同一型号产品连续生产了5K时；e、客户要求试验时4.2试验数量：a、进行极端的破坏性试验时，机器数量为1台至5台；b、环境试验数量为2台至20台4.3、试验具体事项：（如附表一）5、3C符合性检验5.1关键元器件一致性确认：a、核对关键元器件的实物与型式检验报告上的丝印、型号、规格等是否一致。
SE350套管升降器 蛛网操作手册说明书
SE350CASING ELEVATOR/SPIDER OPERATION MANUALSE350-SMGoldenman Petroleum Equipment Co., Ltd Add:7/F, Wanda International Mansion, 67 Fuqian Street , Dongying ChinaTel：+0086-546-8058779 E-mail:********************CONTENTS1. PRODUCT INTRODUCTION2. MAIN TECHNICAL PARAMETERS3. MAIN PARTS STRUCTURE AND WORKING PRINCIPLE4. INSTALLATION5. OPERATION INSTRUCTIONS6. LUBRICATION7. MAINTENANCE8. TROUBLE SHOOTING1. Product IntroductionSE350 casing elevator/spider is a kind of pneumatically operated well head tools, applicable for onshore and offshore casing operation. It can handle casing ranging from 4” to 14”. By operating the reversing air valve may bring slips up or down to clamp or release casing. Meanwhile, the lock device on control valve may lock slips safely.SE500 casing elevator/spider can be used alone as a spider, or as an elevator. The elevator is fitted with a bell guide and bottom guide. The spider is fitted with a top guide that centers the spider over the master bushing. (Fig. 1) The elevator is attached to the derrick traveling block and hook with 350 ton standard API links. The Spider locates directly on the pin drive master bushing (27 1/2 MSPC, 37 1/2 and 49 1/2 MPCH), and square drive master bushing (27 1/2 MSS), and will accommodate any other master bushing when used with an Adapter Plate.Fig.12. Technical Parameters2.1 Applicable casing OD 101.6-355.6mm (4-14in)2.2 Load capacity 3150kN 2.3 Air pressure 0.6-0.8MPa 2.4 Dimensions of elevator 1080*1052*986mm 2.5 Dimensions of spider1080*1052*764mmFig.22.6 Weight of elevator 2473 kg (with one slip assembly)2.7 Weight of spider2383kg (with one slip assembly)2.8 Design and lowest working temperature -20℃2.9 Refer to the following table 1 for Specification of slip assemblies,inserts, bell guides, and top guides.Table 1:InsertsElevatorSpiderCasing Size(in)Slip Body SizeInsertsNumberBeveled InsertsNumberBell Guide Top Guide 424164.1/2216824 2168B 164-4.1/24-4.1/25216924 2169B16555.1/2 2170405.3/45.1/2405.1/2-5.3/45.1/2-5.3/4Inserts Elevator Spider Casing Size(in)Slip Body SizeInsertsNumbe r Beveled Inserts Inserts6.5/82632362632B 2472623362623B 246.5/8-777.5/82633607.3/47.5/82649-1607.5/8-7.3/47.5/8-7.3/48.5/82640482640B 328.3/42650482650B 328.5/8-8.3/48.5/8-8.3/49.5/82633809.5/89.5/89.3/42649-1809.7/89.5/82649-1809.3/4-9.7/89.3/4-9.7/810.3/42640602640B 4010.7/82650602650B 4010.3/4-10.7/810.3/4-10.7/811.3/4263710011.7/811.3/4265110011.3/4-11.7/811.3/4-11.7/812.3/42657602657B 4012.3/412.3/413.3/82636602636B 4013.3/813.3/813.1/22652602652B 4013.5/82653602653B 4013.3/42655602655B 4013.1/2-13.3/413.1/2-13.3/41414263510014143. Main Parts Structure and Working Principle3.1 Main Parts StructureSE350 casing elevator/spider mainly involves housing assembly (include house, active hinged pin, etc.), balance beam assembly, spider assembly (include slips, inserts, etc.), air line assembly (include control valve), air cylinder parts and manual socket. 3.2 Working principleOperating reversing valve will activate air cylinders to raise or lower the slips. The slips are suspended on two inter-locking leveling beams that are driven by four air cylinders. This feature allows the slips to operate in synchronization in both the set and raised positions, while permitting the cylinders to work together so no one cylinder overrides any other, causing misalignment and binding. A manual override system is also provided in theevent of a temporary loss of rig air pressure.A G1/2” filter-regulator (to be prepared by user) will regulate and filter the rig air and send it to the lubricator (mounted on the Elevator and Spider) to add a small amount of oil mist to lubricate the four drive cylinders. The air from the lubricator is sent to the control valve that operates the leveling beams. As directed by the control lever, the air cylinders will raise or lower the slips attached to the leveling beam.4. Installation4.1 Prepare a G1/2” filter-regulator and a tee joint.4.2 Refer to Table 1 and check slips, inserts, bell guide and to guide for meeting the casing size to handle. And ensure all the parts are fixed correctly in place. Refer to Fig.1 and Fig.3 for installation.Regulator-Filter attached to rig air resource4.3 Installing spiderThe spider should be set on master bushing, and fastened by anchor chain. If opening of rotary table is less than 20 1/2” I.D., (with bushing removed), it is needed to install the adaptor plate on the top of rotary table.4.4 Installing elevatorAttach links to two ears of Elevator and secure with bolts.4.5 Connecting Air Lines4.5.1 Mount regulator-filter at a location on derrick. Connect air-in end with air source and the air-out end with a tee joint, which will connect Elevator and Spider respectively.4.5.2 Attach a 50 foot long, 1/2” air line between Elevator and the Stand Pipe located 45 feet above the rig floor, near the derrick stabbing board. Both ends of air lines are quick disconnecting type.4.5.3 Attach a 25 foot 1/2” air line between Spider and regulator-filter.4.5.4 Attach rig air line to regulator-filter and adjust regulator to 0.7-0.8MPa.Note: If the regulator-filter will not remain permanently with rig, use two 50 foot air lines. Tie one 50 foot section of hose 45 feet above floor near casing stabber. Attach second section of hose to first hose with the other end to Elevator.4.6 Removing and Replacing Slip Segments4.6.1 Removing Slip Segments-Fig.4a. Power the slip segments to the up position.b. Connect an overhead lifthook into slip segment lifting ring.With the weight off the removelynch pin.c. Remove link pin.d. Remove a single slipsegment.e. Repeat steps b through cand remove other slip segments.4.6.2 Installing Replacement SlipSegmenta. Apply liberal amount of multi-purpose grease to back of replacement slip segment and mating bowl surfaces.Note: Back of segment and inside of Spider must be clean before applying grease and slip segments.b. Using the hoist, lower the required slip segment in place, aligning link with mating hole on slip segment.c. Install lower pin in place and insert lynch pin in lower pin.d. Repeat steps a through c to install other slip segment.4.7 Removing and Installing Guides4.7.1 Removing Guides-Fig.5a. Remove removable hinge pin with lift.b. Spread hinged body to provide access to guides.c. Remove bolt and keeper from each side of guide ring.d. With an overhead lift, raise the Spider body off the floor and block-up at about 100mm.e. Slide guide ring out of slot in house body.4.7.2 Installing Guidesa. Insert new guides into slot of house body and secure in place with bolts and keeper.b. Lift and close Elevator/Spider house body and insert hinge pin.c. Operate slip segments to determine proper operation, as indicated in Section 5.5. Operation Instructions5.1 OperationThe Elevator and Spider operation is controlled by a lever operated, controlvalve located on the body of each unit. (Fig.6)5.1.1 Moving the lever to the up position raises the slips.5.1.2 Moving the lever to fully down position sets the slips.If an air pressure failure should happen, the slip segments can be operated manually, as follows：a. Place a 5 foot pry bar into manual lift lever.b. Push down on pry bar and move the control lever handle to the up position. This moves the latch plate under the leveling beam to hold slips in the up position.c. To set slips (lower slips) push control lever handle down.5.2 Attentions for operation5.2.1 Only operate the Elevator/Spider when pipe to handlecompletely stops, or it will get stuck.5.2.2 It is necessary to use backup casing tong during making-up or breaking-out. As the Elevator/Spider do not have the function of anti-torque. 5.2.3 Remember to secure the spider with anchor chain and make spider center identical with wellhead center.5.2.4 Lowering speed should be very slow when casing coupling going through Elevator/Spider inside.5.2.5 Add fluid oil after every 50 joint casing run. If sticking of slips happens in the house body, inject fluid oil between house body and slips. (Fluid oil may bring away impurities.)6. LubricationLubricate after every 50 joint casing run and more frequently if necessary to prevent slips from sticking in the Elevator or Spider Body. To lubricate properly the slips should be in the set position without any casing load on unit.Table 2No.Item Number ofLube Point Application Lube Cycle1Bowl/Slip Surfaces16Multi-PurposeWaterless GreaseSee Note Below2Cylinder Assemblies 4Multi-PurposeWaterless GreaseBefore EachJob3Hinge Pins2Multi-PurposeWaterless GreaseBefore EachJob4Flow Control Valve2Multi-purposeWaterless GreaseWeekly5Link Pins8SAE 10 oil Weekly 7. Maintenance7.1 Preventive MaintenanceDO’S1. Lubricate are required in Table2.2. Check guides and gripping inserts for wear and replace as require.3. Avoid unnecessary shock loading of slip segments.Warning:The plastic bowl used on this device can be damaged andpossibly fail if exposed to certain solvents, strong alkalinesubstances, or compressor oils containing aromatic hydrocarbons (fire retardant oils). Fumes of these substances in contact with the bowl can cause damage to the bowl.DON’TS1. Never paint over moving parts or grease fittings.2. Avoid unnecessary impact load on slips.3. Avoid contamination of air lines.4. Never restrict air flow.5. Avoid dry or over-oiled lubricator.6. Never use equipment that is not opening properly.7.2 Transportation and Storage7.2.1 Crash is forbidden when in transportation of the elevator. It must be prevented from rain.7.2.2 The products must be stored in the dry and well-ventilated place and prevented from in the sun or in the rain. It is forbidden to let the products contact acids, alkalis, salts and some other corrosion substance.8. TroubleshootingTroubles Reasons SolutionsSlip Segments do not operate or operate slowly in both directions a. Air pressure at regulator not in therange 0.6-0.8MPa.b. Air lines are pinched or kinked leakswhich could decrease air pressure.c. Not enough oil in lubricator andoperation of the drive cylinders is affected.d. Control valve fails to work.e. Dust ring in cylinders is worn andrestrict cylinder action.a. Adjust the regulator topressure at 0.6-0.8MPa.b. Straight out the airlines.c. Add oil to lubricatoruntil the cylinders canwork normally.d. Repair or replace thevalve.e. Replace the dust ring.Pipe Slips a. One or two incorrect slip segmentsmixed with correct size slip segments.b. Worn or damaged inserts.c. Back of slip segment is worna. Check and replacewith correct segments.b. Replace inserts.c. Repair or replace slips.Damage on pipe a. There is incorrect slip segment in slipassembly.b. Badly worn or damage of inserts.a. Check and replacewith correct segments.b. Replace inserts.Exploded View of SE350 Casing Elevator/SpiderParts List of SE350 Casing Elevator/SpiderNo.Part No.Description Qty.1RS297.000-（01～15）TOP GUIDE(4-14")2/each 2ASME BOLT, Hex Head 3/4"-10×2"63ASME LOCKWASHER 3/4"64RS297.000-01COVER25RS297.200-02LINK PIN, Upper46RS297.200-03LINK, Slip Hanger47ASME NUT, Hex, 1.1/4"-12UNF48ASME LOCKWASHER 1.1/4"49ASME FLATWASHER 1.1/4"4 10RS297.200-01LEVELING BEAM2 11RS297.210.00A LINK PIN, Lower4 12RS295.100-02LONG BOLT2 13GREASE FITTING, 1/8 NPT 18 14RS295.300.00SLIP SEGMENT4/each 15ASME CAP SCREWS 3/4" -10×2"2 16RS297.100-05BUTTON, Register2 17RS297.100-06GUIDE,KEPPER4 18ASME BOLT, Hex Head,1"-8×2-1/2"4 19ASME LOCKWASHER 1" Dia.4 20RS297.000-29GUIDE RING2 21RS297.600.00BELL GUIDE2 22RS297.100-01BODY2 23ASME BOLT, Hex Head, 1/2" -13x1-1/28 24ASME LOCKWASHER 1/2" Dia.8 25RS297.220.00LYNCH PIN4 26GB/T91COTTER PIN 5×40 8 27RS295.110.00HINGE PIN, Removable1 28RS295.110-02HINGE PIN, Stationary1 29ASME BOLT, Hex Head,5/8"-11×1-3/4"10 30ASME LOCKWASHER 5/8"18 31RS297.520.00LUBRICATOR MOUNTING BRACKET1 32ASME BOLT, Hex Head,1/2"-13×1.1/2" 8 33RS297.000-31CYLINDER HOLDING BLOCK8 34RS295.200-01BRACKET SEAT1 35RS295.200-02SUPPORTING BLOCK 136RS295.200-03PIN1 37ASME NUT, Hex, 1.1/8"-12UNF2No.Part No.Description Qty.38RS297.510.00CONTROL VALVE and LATCH ASSEMBLY139RS297.700-02PIN,PIVOT φ25.41 40GB/T91COTTER PIN 3.2×40 2 41RS297.700-01MANUAL CONTROL BRACKET1 42RS297.700-03SOCKET,MANUAL LIFT1 43RS297.400.00CYLINDER4。
SMS 4 SMS 5安全门板产品介绍说明书
SMS 4 / SMS 5 safety mat Product informationSafety mats are used forthe protection of man on machinery and plants with hazardous movements. Typical fields of application are, for instance, the protection of hazardous areas and surfaces on wood-processing machines, scissor lifts or punching presses.The safety mats build a uniplanar safety device, which detects the presenceof persons. If a person steps onto the safety mat, the connected safety-monitoring module will immediately stop the hazardous movement. The safety mats can be connected in line with each other in order to provide for a smooth and fast protection of hazardous areas. To this end, different standard sizes are available. Futhermore, special sizes or special shapes can be realized upon request.The SMS 4 series is connec-ted to the floor by meansof an aluminium profile and special corner sections. As a result of the beveled form of the profile, tripping hazards are avoided. The aluminium profile additionally serves as edge protection, when fork-lift trucks or other floor conveyors drive over the safety mats.In the SMS 5 series, the po-lyurethane actuating profile is directly moulded to the active surface of the safety mat.The safety mats are characterized by their very robust design and high resistance to acids, caustic solutions, oil and gasoline. In combination withthe SRB 301HC/R or SRB 301HC/T safety-monitoring modules, the safety mats meet the requirements of control category 3 to EN 954-1.SMS 4 / SMS 5 safety mats2Safety distanceThe proper arrangement of the safety mat with regard to the adjacent hazardous area mainly depends on the after-travel time of the machine and the approaching speed of the operator. The standard EN 999 (Safety of Machinery, Approaching Speed ofBody Members) provides a formula to calculate the safety distance for this connection.Safety distanceS = K x (T1 +T2) + (1200 - 0,4 H)S M inimum safety distance in millimetres, measured fromthe hazardous area to thedetection point, the detec-tion line or the protectedfieldK C onstant in millimetres per second, derived from datathrough the approachingspeed of the body or thebody member (1600 mm/s)H D istance through the refe-rence plane (e.g. the floor)in millimetres (for safetymats generally 0 mm)T1 t he maximum responsetime of the safety devicebetween the triggering ofthe perceptive element (thesafety mat) and the time,at which the safety guard(safety-monitoring module)has switched the outputsignal to the "OFF" state.T2 t he response time of themachine, i.e. the timerequired to shutdown themachine or to eliminate therisk, after the transmissionof the output signal of thesafety guardT he safety distance there-fore generally can be calcu-lated in the following way:S = 1600 mm/s x (T1 +T2) +1200 mmExample:The safety distance must becalculated with a responsetime of 142.5 ms for the ma-chine and a response time of45 ms for the safety guard.The safety mat is installed atground level.S = 1600 mm/s x (0.045 s +0.1425 s) + 1200 mmS = 1600 mm/s x (0.1875 s)+ 1200 mmS = 300 mm + 1200 mmS = 1500 mmCalculation of the safety distance to the danger point3Safety mats• Certified to EN 1760-1• Control category 3 to EN 954-1 in combination with safety-monitoring module SRB 301HC/R• Response time max. 25 ms• Robust design• High resistance to chemicals• Slip-free surface• Cascading possible• Special sizes and shapes available on request• No additional terminating resistor required • Aluminium frame and corner sections availableLegend:A: active surface • Certified to EN 1760-1• Control category 3 to EN 954-1 in combination with safety-monitoring module SRB 301HC/R• Response time max. 25 ms• Robust design• High resistance to chemicals• Slip-free surface• Cascading possible• Special sizes and shapes available on request• No additional terminating resistor required • With moulded ramp profileLegend:A: active surfaceTotal size = A + 2 x 35 mmApprovals F Approvals FOrdering details Ordering detailsSMS 4-➀No. Option Description➀Active surface 250-500250 x 500 mm500-500500 x 500 mm500-1000500 x 1000 mm750-1000750 x 1000 mm1000-10001000 x 1000 mm1000-15001000 x 1500 mm SMS 5-➀No. Option Description➀Active surface250-500250 x 500 mm500-500500 x 500 mm500-1000500 x 1000 mm750-1000750 x 1000 mm1000-10001000 x 1000 mm1000-15001000 x 1500 mmStandards: EN 1760-1Control category: 3 to EN 954-1Surface material: polyurethane, blackProtection class: IP 65 to EN 60529Ambient temperature: 0° C ……60°CFitting height: 14 mmWeight: 17 Kg / m2Actuating force: 150Nwith round body ø 80mmCable: 4 x 0.34 mm2 SMS42 pc. 2 x 0.34 mm2 SMS 5Cable length: 6mResponse time: ≤ 25 msMechanical life: >1.5 million operationsAdmissible load: 2000 N / 80 mm øInactive edge ≤ 10mmNoteChemical resistance:Water : Good10% acids: Resistant10% caustic solutions: ResistantOils: ResistantG asoline: ResistantOther on requestin preparationin preparation4SMS 4 safety mats accessoriesOrdering detailsFixing rail3000 mm long SMS 4-BS-3000Ordering detailsCorner section (1 pc) SMS 4-EVOrdering detailsRamp rail3000 mm long SMS 4-RS 3000Trim kits(Includes ramp rail and corner sections)250x500 mm SMS 4-RS 250-500500x500 mm SMS 4-RS 500-500500x1000 mm SMS 4-RS 500-1000750x1000 mm SMS 4-RS 750-10001000x1000 mm SMS 4-RS 1000-10001000x1500 mm SMS 4-RS 1000-150056Standards:IEC/EN 60204-1, IEC/EN 60947-5-1, EN 954-1, BG-GS-ET-20Classification to EN 954-1: control category 4Start conditions:automatic or start button (optionally monitored)With feedback circuit (Y/N): yes ON delay with reset button:≤ 50 ms Drop-out delay on "emergency stop": ≤ 20 ms Drop-out delay on "supply failure": ≤ 100 msRated operating voltage U e : 48-240 VAC; 24 VAC/DCFrequency range:50 / 60 HzFuse rating for the operating voltage:230 VAC version: primary side: melting fuse, tripping current >1.0 A;secondary side: internal electronic fuse, tripping current > 0.12 A; 24 VAC/DC version:internal electronic fuse, tripping current > 0.5 AInternal electronic fuse (Y/N): 230 VAC version: no 24 VAC/DC version: yes Current consumption:230 VAC version: 1.6 W; 4.2 VA 24 VAC/DC version: 1.4 W; 3.3 VAInputs monitoring: Cross-wire detection: yes Wire breakage detection: yes Earth leakage detection: yes Number of NC contacts: 2Number of NO contacts: 0Max. total line resistance: 40 ΩOutputs:Stop category 0: 3Stop category 1: 0Number of safety contacts: 3Number of signalling outputs: 1Max. switching capacity of the safety contacts: 250 VAC, 8 A ohmic (inductive with suitable protective circuit)Utilisation category to EN 60947-5-1: AC-15: 230 V / 6 A DC-13: 24 V / 6 A Mechanical life: 107 operationsAmbient conditions:Operating ambient temperature: – 25°C … + 60°C Storage and transport temperature: – 25°C … + 85°C Protection class: enclosure: IP 40, terminals: IP 20, terminal space: IP 54Mounting: snaps onto standard DIN rails to DIN EN 60715Connection type: plug-in type screw terminals min. cable section: 0.25 mm 2 max. cable section: 2.5 mm 2Weight: 230 VAC version: 340 g 24 VAC/DC version: 320 g Dimensions (height/width/depth): 100 x 45 x 121 mm Note : Inductive loads (e.g. contactors, relays, etc.) areto be supressed by means of a suitable circuitSafety mats• Safety-monitoring module for safety mats • 3 enabling contacts • 1 signalling contact • Cross-wire detection• Feedback circuit to monitor external contactors• Monitored start or automatic start • LED status indication • Plug-in terminalsApprovalsH FSRB 301HC/➀-➀No.Option Description ➀R Manual start T Automatic start ➀230 V 48-240 VAC 24 V24 VAC/DCSafety mats• Protection of a safety mat toand EN 1760-1• Start button with edge detection• Feedback circuit S to monitorthe external contactors• Series-wiring of multiplesafety mats possible• Reset button JSMSSThe wiring example is shown with the safety mat in non-actuated and de-energized condition.715 Skyline DriveTarrytown, New York 10532Tel: (914) 347-4775Fax: (914) 347-1567E-mail:**********************USA29 Centennial Road, Unit 1Orangeville, Ontario L9W 1R1Tel: (519) 307-7540Fax: (519) 307-7543E-mail:*************************www.schmersalcanada.caCanada。
早教朗器工作坊综合assembling指南说明书
saw holder©2008 Lakeshore LC104 (800) 428-4414Ages 3+Assembling the WorkbenchMedium pilot holes face outward.Secure the bolts that are closest to the corners first.Make sure the edges of the legs are flush with the frame.Small holes on edges face ends of table.Use 2 bolts, 2 washers, and 2 nuts to secure each leg. You may want to use an adjustable wrench for steps 2 and 3.Note:Tighten the bolts only until snug. You will tighten them completely when all the bolts and screws are in place.are flush. Push the legs sideways if needed. (They will “give” a little.)3.Attach the long braces to the legs. Be sure to tighten the bolts that are closest to the corners first.bolts first.4.Attach the short braces.These edgesmust be flush.Attach the screwsthat go into thelong braces first.edges are flush,and then attach the screws that gointo the legs.e 6 screws to secure the legs to the table top.6.Position the vise on the pre-attached vise block as shown below.Make sure the left edge is flush with the table. Then, use a hammer and nail to create four starter holes in the vise block. To do this,simply tap a nail into the vise block using the holes in the vise as a guide.e 4 screws to secure the vise.Note:8.Position the saw holder as shown,aligning the brackets with the pilot holes. Use the 2 saw holder screws to secure the holder.9.Now it’s time to use a little muscle. Tighten every screw and bolt all the way in! (A socket wrench will make this task easier.) Once everything is secure, turn the workbench over.10.From the side, slide the bottom shelf between the legs and drop itinto place.Dark panel11.Insert the hardware cup in the round hole. (The square holes are designed to hold hammers.)Important Safety Note:Woodworking tools are dangerous. Never allow children to usetools without adult supervision. When children are not using the workbench, remove the saw, hardware, and other toolsfrom their holders and store them safely out of children’s reach.。
Belimo B350 50型号3路混合 分流阀数据表说明书
B350•Stainless Steel Ball and StemType overviewType DNB35050Technical dataFunctional data Valve size2" [50]Fluid chilled or hot water, up to 60% glycolFluid Temp Range (water)0...250°F [-18...120°C]Body Pressure Rating400 psiClose-off pressure ∆ps200 psiFlow characteristic A-port equal percentage, B-port modified forconstant common port flowServicing maintenance-freeFlow Pattern3-way Mixing/DivertingLeakage rate0% for A – AB, <2.0% for B – ABControllable flow range75°Cv57Cv Flow Rating A-port: as stated in chart B-port: 70% of A – ABCvMaterials Valve body Nickel-plated brass bodyStem stainless steelStem seal EPDM (lubricated)Seat PTFECharacterized disc TEFZEL®Pipe connection NPT female endsO-ring EPDM (lubricated)Ball stainless steelSuitable actuators Non-Spring ARB(X)Spring AFSafety notesWARNING: This product can expose you to lead which is known to the State of California tocause cancer and reproductive harm. For more information go to B350ApplicationMode of operationProduct featuresThis valve is typically used in air handling units on heating or cooling coils, and fan coil unit heating or cooling coils. Some other common applications include Unit Ventilators, VAV box re-heat coils and bypass loops. This valve is suitable for use in a hydronic system with variable or constant flow.Flow/Mounting detailsProduct featuresLocal Control SY2~12, 110vac ModDimensionsType DN B35050ARB, ARXAB C D E F H110.5" [267]4.9" [125]7.7" [196]6.0" [152]1.7" [44]2.6" [66]0.8" [20]ARB N4, ARX N4AB C D E F 11.4" [289]4.9" [125]9.8" [249]8.0" [203]3.1" [80]3.1" [80]B350ARQB, ARQXA B C D E F H1H29.9" [251] 4.9" [125]8.3" [211] 6.6" [168] 2.3" [58] 2.6" [66]0.8" [20]0.6" [15]AFRB, AFRXA B C D E F11.3" [286] 4.9" [125]8.3" [211] 6.6" [168] 2.6" [66] 2.6" [66]AFRB N4, AFRX N4A B C D E F13.0" [330] 4.9" [125]11.8" [300]9.9" [251] 3.7" [95] 3.7" [95]ARX24-3-T N4FootnotesNEMA 4X, On/Off, Floating Point Control, Non-Spring Return, 24 VTechnical dataElectrical dataNominal voltageAC/DC 24 V Nominal voltage frequency 50/60 Hz Power consumption in operation 2.5 W Power consumption in rest position 0.5 WTransformer sizing 5.5 VA (class 2 power source)Electrical Connection Terminal blocksOverload Protectionelectronic thoughout 0...90° rotation Functional dataDirection of motion motor selectable with switch 0/1Manual override under cover Angle of rotation 90°Angle of rotation note adjustable with mechanical stop Running Time (Motor)90 s / 90°Running time motor variable 90 or 150 s Noise level, motor 45 dB(A)Position indicationpointer Safety dataDegree of protection IEC/EN IP66/67Degree of protection NEMA/UL NEMA 4XEnclosure UL Enclosure Type 4XAgency ListingcULus acc. to UL60730-1A/-2-14, CAN/CSA E60730-1:02, CE acc. to 2014/30/EU and 2014/35/EU Quality Standard ISO 9001Ambient temperature -22...122°F [-30...50°C]Ambient temperature note -40...50°C for actuator with integrated heating Storage temperature -40...176°F [-40...80°C]Ambient humidity Max. 100% RH Servicingmaintenance-freeMaterialsHousing material Die cast aluminium and plastic casing†Rated Impulse Voltage 800V, Type of action 1, Control Pollution Degree 4.Electrical installationINSTALLATION NOTESProvide overload protection and disconnect as required.Actuators may be connected in parallel. Power consumption and input impedance must beobserved.Actuators may also be powered by DC 24 V.ARX24-3-T N4Actuators Hot wire must be connected to the control board common. Only connect common toneg. (-) leg of control circuits. Terminal models (-T) have no-feedback.Actuators are provided with a numbered screw terminal strip instead of a cable.Meets cULus requirements without the need of an electrical ground connection.Warning! Live electrical components!During installation, testing, servicing and troubleshooting of this product, it may be necessaryto work with live electrical components. Have a qualified licensed electrician or other individualwho has been properly trained in handling live electrical components perform these tasks.Failure to follow all electrical safety precautions when exposed to live electrical componentscould result in death or serious injury.Wiring diagramsOn/Off Floating PointFloating Point - Triac Source Floating Point - Triac SinkDimensions。
ASTM A350-2004
7.1.3 试验的位置和方向——试验样品应从锻件或试验毛坯最厚的截 面上取下，截面的位置按照,7.1.3.1, 7.1.3.2, 7.1.3.5 或根据锻件的尺寸和 形状，尽可能接近所规定的位置。 7.1.3.1 对于锻件或试验毛坯，它的最大热处理厚度 T 为 2 英寸（50 毫米）或以下时，试样 的纵向轴应在其厚度中间取下，试验样品的中间长度至少从第二个热 处理表面起 2 英寸（50 毫米）处，不包括最大热处理厚度 T 尺寸的 表面。（这种情况一般指 1/2T×2 英寸【50 毫米】）。？？？ 7.1.3.2 对于锻件的或试验毛坯的最大热处理厚度 T 大于 2 英寸（50 毫米）时，试验样品的中心轴应从最接近的热处理表面算起的 1/4T 处，从任何第二个热处理表面量起最大热处理厚度应为 T 或 4 英寸 （100 毫米），取最小值。淬火和回火的锻件，试验样品的中间长度应 是离任何第二个热处理表面至少 T 的距离。单独锻制的淬火和回火锻 件的试验毛坯，其试样位置见图 1。
的锻造材料，和这种小规格中最大尺寸样品沿切口宽度至少是锻件厚 度的 80%，试样应按照表 4 的温度进行试验，当小规格最大尺寸样品 沿切口宽度小于材料厚度的 80%时，试验温度应低于表 4 的温度，这 个降低值是对应于代表材料厚度的温度降低数和对应于实际测得试 样宽度的温度降低数的差。 7.3 硬度试验 7.3.1 只生产一个锻件的情况除外，7.1.2.1 规定的每批 HB 熔炉量或连 续熔炉热处理中至少两个锻件要进行硬度试验，以保证在热处理后， 锻件机械性能的硬度不超过 197HB。硬度测量方法应根据 A370 试验 方法和定义。当只生产一个锻件时，它也要进行硬度试验，以保证它 的硬度符合本规范的 197HB 最大值，只要试验不影响锻件的用途， 购买方可通过在锻件的任何地方进行试验来证明它已经符合本规范 的要求。
Gator Cases 混音台混音器与配件交叉参考表说明书
G-Mix-B 2020: (20" x 20" x 5.5")Manufacturer Model TypeALESIS STUDIO 24 MixerALLEN & HEATH XONE 464 MixerALTO AUDIO L-16 MixerALTO AUDIO L-20 MixerALTO AUDIO PM-12 DRAGONFLY MixerBEHRINGER MX1804X MixerBEHRINGER MX2004A MixerBEHRINGER PMH1000 Powered Mixer BEHRINGER PMH3000 Powered Mixer BEHRINGER PMP1000 Powered Mixer BEHRINGER PMP3000 Powered Mixer BEHRINGER UB2442FX-PRO MixerBEHRINGER XENYX 2442 FX MixerCOOPER SOUND SYSTEM 6 MixerCOOPER SOUND SYSTEM 8 MixerCREST AUDIO XR20 MixerCREST AUDIO XR24 MixerCREST AUDIO XRM MixerDIGIDESIGN COMMAND 8 MixerDIGIDESIGN DIGI-003 MixerMACKIE 1604 VLZ PRO MixerMACKIE 1642 VLZ PRO MixerMACKIE 1642-VLZ3 MixerMACKIE CFX 12 MixerMACKIE CFX12MK2 MixerMACKIE HUI MixerNADY CMX16A MixerNADY MXE1212 MixerPEAVEY RQ 2310 MixerPEAVEY UNITY 1002-8 RQ MixerPHONIC MM1805(X) MixerPHONIC MR 1843X MixerPHONIC POWERPOD 1840 MixerPHONIC POWERPOD 1860II MixerROLAND MC-909 SequencerROLAND MV-8000 SamplerROLAND MV-8800 Recording Workstation ROLAND VS-2400CD Recording Workstation SAMSON MDR10 Mixer SOUNDCRAFT FX8 Mixer SOUNDCRAFT MPM12 (NO SIDE PANELS) Mixer SOUNDCRAFT SPIRIT E8 Mixer SOUNDCRAFT SPIRIT FX8 Mixer SOUNDCRAFT SPIRIT M12 Mixer SOUNDCRAFT SPIRIT M8 Mixer STUDIOMASTER CSX MixerTASCAM FW-1082 Recording Interface TOPAZ S18-4 MixerYAMAHA 01X Digital InterfaceG-Mix-B 2020: (20" x 20" x 5.5")Manufacturer Model TypeYAMAHA EMX3000 MixerYAMAHA MD4S Recording Workstation YAMAHA MD8 Recording Workstation YAMAHA MG124C MixerYAMAHA MG124CX MixerYAMAHA MG16/4 MixerYAMAHA MG16/6FX MixerYAMAHA MX12/4 MixerYAMAHA MX12/6 MixerYAMAHA MX200-8 MixerZOOM MRS1608CD Recording Workstation This list is intended as a guide; not a substitute for testing the actual fit of an instrument. All product information referenced above is based on the manufacturer's published specifications. These specifications may change over time and without notice. If you have questions on a specific case or product, or see that a correction is needed, ***********************************************************************************.。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
What to Look for in a Job Posting
1. Name of company, position title, field: 2. Primary needs of company as stated: 3. Any implied needs: 4. Immediate priorities of company: 5. Job responsibilities: 6. Expectations of employer: 7. What do you think the personal qualities or traits of a successful applicant would be? 8. What experiences do you have that are in the field and/or represent similar responsibilities, personality traits, or priorities?
Some Common Terms in Job Postings
PROFICIENCY REQUIRED Besides the generic traits that employers like to see in applicants for any position, job advertisements will make statements about specific skills related to a specific job. It seems that the most favorite description to use is "proficiency in". Other popular descriptors are "command of" and "working knowledge of". These phrases might be used to describe understanding of software, industry expertise, etc. They all mean the same thing, but many people don't realize what that is. Whenever you see specific skill requirements and wonder whether or not you meet them, consider these issues: Being proficient means being comfortable using something on a day-to-day basis and being able to answer simple questions about it. When it comes to languages, there is a difference between being fluent and understanding most things. There is no shame in saying you have a "conversational" understanding. Certain skills have official certifications. If you have an official certification, be sure it is on your resume. If the same skills continue to pop-up in job postings, it may be time for you to acquire them.
Brainstorming: Finding Applicable Skills
Think about the particular field you are planning on applying for a job in.
Start with organizational skills. Think about a project you have done in class or for a club in either high school or college. How would you describe it for an employer? How could you stress teamwork and ability to work to deadline? Next, think about Proficiency. For your field, what proficiencies will they expect? What classes have you taken and projects have you done that would be important for your employer to know? Finally, think about experience. Assume you want to apply for a job that asks for a few years of experience that you do NOT have. What experience, either in a class project, at a part time job, or for a club or organization could you relate to the actual job?
Some Common Terms in Job Postings
ORGANIZATION SKILLS REQUIRED Anytime a job advertisement makes a point to mention "organizational skills" or "communication skills", the employer actually wants to know three things: do you get the job done on time, do you do the job correctly, and do you work well in teams. Be sure to incorporate your ability to work with deadlines and work on team projects into your resume. Your resume creates the first image an employer will have of you. That image must be what the employer is looking for. Employers love multi-tasking. Convey the fact that you had many responsibilities at previous jobs, and you always succeeded. Don't beat around the bush. Explicit examples are always good. If they do not fit in your resume, work them into your cover letter. Otherwise, be sure to mention them in your interview.
Brainstorming: Finding Applicable Skills
When you apply for your first job, you often don’t have the exact skill set they are looking for. So it is important to think about what experiences you can use from your life to show the potential employer you have what it takes.
Brainstorming: Finding Applicable Skills
One last question:
Which of these fields (organization, proficiency, experience) do you most need to work on before you apply for a job? Realistically, what might you do in the next few years?
BADtegies
Matching Skills and Employer’s Needs
Some Common Terms in Job Postings Brainstorming: Finding Applicable Experiences What to Look for in a Job Posting Example Job Posting
Some Common Terms in Job Postings
(/newsletter/interpreting-job-postings.html)
EXPERIENCE REQUIRED The single most common requirement stated in job advertisements is experience. Some positions require no experience at all, while others might require 1-2 years of experience, while the most senior positions might require 10 or more years of experience! These numbers can be very intimidating, but the right approach can make a difference. When thinking about the experience required by a job, consider these three options: Tailor your resume to fit the job description. If an advertisement says that a position requires 3 years of experience in sales, make sure your resume highlights the fact that you have 3 years of experience in sales Work experience is NOT just typical jobs. Internships, volunteer work, and clubs are all valid forms of experience. Any learning opportunity is considered work experience. Not meeting experience requirements does not take you out of the running. More than anything, companies want good employees. Between your resume and your cover letter, if you can persuade a company to think you are diligent and quick to learn new skills, you have a good shot at the job.