精密仪器手表行业表面检查指引登记表dial inspection guide

Inspected by eye 視檢
2.19 Logo requirement
字嘜要求
Receive goods according to P.O.,Can refer to stocked sample or stocked goods 照P.O.要求收貨﹐可參考存辦或存貨
Inspected by eye 視檢
Inspected by eye 視檢
2
Dial(表面)
Inspection Qty 抽檢數量LEVEL S1
Qualified Target 合格指標 1.0
2.01 Dial outer diameter Receive goods according to drawing Normal Tolerance:+010/-005
and edge貼邊字距 確認邊字位印刷﹐不會被殼開面位遮蓋
2.11 Number and Index
Centripetalism
Inspect with standard printed line and confirm it is centripetal
字﹐釘向心情況 用參考之印線菲林咭作檢視﹐能向心便可。
2.14 Components tightness status 種件松緊情況
No components out when fall on a hard flat from 1/3m highness 于一尺高以上跌于硬台面﹐無任何種件甩出便可
Clamp 夾具
2.15 Dial feet Tightness No feet fall off when pull the feet with clamp
movement 表面配機芯
window size should fit with movement 試配機芯﹐面腳要能順配及要對十字線﹐面孔及窗距要與機芯配合
Callipers 卡尺
Callipers 卡尺
Inspected by eye 視檢
Callipers edge 卡尺邊 With hand and inspect by eye 徒手﹐視檢
面腳松緊
用夾鉗鉗緊橫拉﹐甩腳便可
Clamp 夾鉗
2.16
Receive goods according to P.O.,Can refer to dial color sample or stocked
Dial color 表面顏色 goods
Inspected by eye
照P.O.要求收貨﹐可參考面顏色辦或存貨（于石英燈下顏色需不變） 視檢
2.12 Case back flatness
status
Confirm the case back is flat and have no pin feet,glue etc.
面底平坦情況
確認面底要平坦及無什么物凸出﹐如釘腳﹐膠水類
2.13 Dial fit for
Dial feet could match and fit with cross line,dial post and
Inspection Qty 抽檢數量LEVEL2
Qualified Target2.5 合格指標 2.5
Inspect the scratching, pin sctatching,black spot and index status (take sample of scratching and spot for reference) 檢查面花﹐釘花﹐面黑點﹐字釘情況（參考花﹐點限度辦）
2.2 Luminaire status 夜光情況
Confirm that is luminant when in black place 需于黑暗位置確定夜光能發光
Inspected by eye 視檢
2.21
After confirm that dial fit with movement,stem place should be correspond
表面外徑
照圖紙收貨 一般公差+010/-005
Callipers 卡尺
2.02 Dial thickness 厚度
Receive goods according to drawing Normal Tolerance:+005/-003 照圖紙收貨 一般公差+005/-003
Callipers 卡尺
2.09 Dial feet size 面腳
Receive goods according to drawing Normal Tolerance:+/-005 照圖紙收貨 一般公差+/-005
2.1 Distance between
Number
Confirm that the printed number willn't be covered by dial operning
2.17 Color of pin and stone 釘﹐石顏色
Receive goods according to P.O. 照P.O.要求收貨
Inspected by eye 視檢
2.18 Dial style requirement 面款要求
Receive goods according to P.O.,Can refer to stocked sample or stocked goods 照P.O.要求收貨﹐可參考存辦或存貨
日歷窗尺寸
照圖紙收貨 一般公差+/-005
2.08 Distance of calendar Receive goods according to drawing Normal Tolerance:+/-005
window日歷窗距 照圖紙收貨 一般公差+/-005
Callipers 卡尺 Callipers 卡尺 Callipers 卡尺
2.06 Dial post diameter Receive goods according to drawing Normal Tolerance:+/-005
配面針柱直徑
照圖紙收貨 一般公差+/-005
2.07 Calendar window size
Receive goods according to drawing Normal Tolerance:+/-005
Stem place 霸芯時位
to original disign,can refer to the drawing of dial and component spec.
需確定表面配機芯后﹐霸芯時位位置與原定設計相符﹐可參照有面圖
紙及
Inspected by eye
配件規格之注明
視檢
字釘石尺寸
照圖紙收貨 一般公差+/-010
Callipers 卡尺
2.05 Pin,Stone height 釘﹐石高度
Receive goods according to drawing Normal Tolerance: Pin:0.30+/-005 Stone:0.45+/-010 照圖紙收貨 一般公差 釘:0.30+/-005 石:0.45+/-010 Callipers 卡尺
Dial Inspection Guide 表面檢查指引
As for 圖the紙尺 寸﹐如 ==抽Ac檢cepted 合格
No. 序號
(7.6) Dial Inspection Guide
(7.6)表面檢查指引
Inspection Report No.檢查報告編號﹕
x= Rx e=je抽cte檢d 不合格
2.03 Outer index ring size Receive goods according to drawing Normal Tolerance:+/-015
外字圈尺寸
照圖紙收貨 一般公差+/-015
Callipers 卡尺
2.04 Index,Pin,Stone Size Receive goods according to drawing Normal Tolerance:+/-010
O= ROeq=ui需red 作全檢
NA = Not Applicable
NA = 此欄不適用
Item 項目
Reference 數據
Tool 工具
Filled工by程部需及時填寫
Technical
Judgeme
Spec. 規 Actual Testing nt
格
實測
判斷
1
Dial(表面)
1