新版NS-1 钻铤标准(2013版中英对照)

Quality & Inspection Requirements for New and Refurbished
Drilling and Well Completion Equipment
关于新制和翻新钻井和完井装备的质量与检验的要求
NS-1 Number: NS 03.38.10.1110
Revision Date: January 2013
Equipment Name: DRILL COLLARS
Manufacturer: GENERAL
Model/Type: TYPICAL VARIOUS
Material Group: LOW ALLOY STEEL
Service: NON-SOUR
NS-1编号：NS 03.38.10.1110
修订日期：2013年1月
装备名称：钻铤
制造厂商：通用
型号类型：所有类型
金属级别：低合金钢
工作范围：非酸性环境
Rev Date Description Change Note
01 08/92 SUPPLEM. REQ.’S, PART 4, RENUMBERED
APPLICABLE PARA’S AND ADDED TITLES
02 01/95 REF. SUPPLEMENTARY REQ. PARA 2; ADDED 3
NEW SUB-PARA’S ON COLD WORK ’CW’ STAMP,
BENCHMARK & NOTE. PARA 2 & 4.4 REPLACED API
RP 7G WITH ISO 10407, ADDED ELEVATOR RECESS
03 11/04 FORMAT CHANGE
04 06/07 MINOR HEADER AND FRONT PAGE ADJUSTMENT
05 01/13 INTERNAL REVIEW
修订日期说明修改备注
01 1992.08 补充要求第4部分重新编写了适用部分的编号，增加了标题
02 1995.01 参考补充要求第2部分增加了3条有关冷滾压的模印“CW”、
基准标识和注意等新的子部分。

第2部分和4.4用ISO 10407
替换了API RP 7G，增加了吊卡瓦槽。

03 2004.11 格式变化
04 2007.06 小幅标题和网页调整
05 2013.01 内部审核
SCOPE
This GENERAL NS-1™ specifies the minimum quality and inspection requirements applied to wrought Low Alloy Steel Drill Collars, covering the following types:
1. Cylindrical (slick) drill collars
2. Cylindrical (slick) drill collar pup joints
3. Drill collars with slip recess
4. Spiral drill collars
5. Spiral drill collar pup joints
范围：
本通用NS-1标准规定了适用于锻造的低合金钢钻铤的最低质量和检验要求，包括如下类型：
1.圆柱（光滑）钻铤
2.圆柱（光滑）钻铤短节
3.带卡瓦槽的钻铤
4.螺旋钻铤
5.螺旋钻铤短节
It applies to:
• All operating temperatures
• Non-SOUR service conditions
• All drill collar sizes
This equipment shall conform to the requirements of API Spec.7-1 (ISO 10407-1), API Spec 7-2 (ISO 10407-2) and the requirements of this NS-1™. If in conflict the requirements of this NS-1™ shall prevail.
Design verification, approval and other design related parameters are specifically excluded from this NS-1™.
适用于：
•所有操作温度
•非酸性工作环境
•所有钻铤尺寸
这些装备应该符合API Spec.7-1 (ISO 10407-1)、API Spec 7-2 (ISO 10407-2)和本NS-1标准的要求。

如与本标准相抵触则执行本标准。

设计校对、审批和其他相关参数的设计不包括在本标准范围之内。

SUPPLEMENTARY REQUIREMENTS
The following requirements are supplementary to and shall be applied in conjunction with the quality subspecifications called out in the matrix of this NS-™1 Specification.
1. WELDING
No fabrication or repair welding shall be performed.
补充要求
下列要求为补充要求，连同本NS-1规范清单列出质量子规范一并应用。

1.焊接
不进行制造焊接或修理焊接。

2. THREADED CONNECTIONS AND RECESSES
2.1 The thread roots of all API rotary connections NC38 and larger shall be cold rolled after final machining.
2.2 All API rotary pin connections NC38 and larger, shall be provided with a stress relief groove to API Spec. 7-2 latest revision.
2.3 All box connections NC38 and larger shall be provided with a stress relief feature which may be either external or internal (e.g. API style, Drilco style, ’bore-back’).
2.4 All stress relief features and radii of the upper shoulders of the slip and elevator recesses shall be cold worked after final machining. All connections which have been cold worked shall be marked by stamping the connection with a circle enclosing the letters ’CW’ as specified in API Spec. 7-2 latest revision.
2.螺纹连接和应力槽
2.1 所有API标准的NC38及更大尺寸的旋转连接的螺纹根部在最终机械加工结束后都应进行冷滾压。

2.2 所有API标准的NC38及更大尺寸的旋转连接的外螺纹都应按照API Spec 7-2最新版提供应力释放槽。

2.3 所有API标准的NC38及更大尺寸的旋转连接的内螺纹都应在其外部或内部提供应力释放结构（如：API型、Drilco型、bore-back型）。

2.4 所有应力释放槽和吊卡瓦槽上部台肩的R处都应该在最终机械加工结束后进行冷滾压。

所有进行过冷滾压的螺纹连接都应该按照API Spec7-2最新版规定在螺纹连接处模印内有“CW”字母的圆环。

2.5 All new rotary connections shall be provided with a benchmark (this does not apply to pin connections having a stress relief groove) in accordance with the requirements of ISO 10407-2, latest revision as a minimum. The preferred form of the benchmark is an indicator which provides a 360°reference around the connection. This type of benchmark is superior to the API one, in that it reveals not only the extent of refacing but also how perpendicular the refaced seal is to the pipe’s axis.
Note: Various manufacturers can provide the preferred 360° benchmark form. The purchaser should confirm this with the supplier prior to manufacture.
2.5 所有新的旋转螺纹连接都应该按照ISO 10407-2最新版最低要求提供一个基准标识（这条不适用于具有应力释放槽的外螺纹连接）。

基准标识的首选形式是提供一个围绕螺纹连接的360°参照指示。

这种基准标识优于API的基准标识，它不仅显示了基准面的范围，而且也显示了基准密封面与管体轴线的垂直度。

注意：各制造商可以提供优先的360°基准标识形式。

购买方应该在制造之前与供应方进行确认。

3. MATERIAL TESTING (Ref. Sub-Spec. 10.1 & Sub-Spec. 10.4)
3.1 Chemical Analysis
Chemical analysis shall be carried out on a heat basis, demonstrating conformance to the manufacturer’s applicable material specification for all elements tabulated.
3.2 Tensile Testing
Tensile testing to ASTM A370 shall as a minimum, establish yield strength, tensile strength, elongation and reduction in area on a heat/heat treatment lot basis.Test specimens shall be taken from a location as per API Spec. 7-1.
3.材料试验（参考子规范10.1和子规范10.4）
3.1 化学分析
化学成分分析应按炉取样，应包括制造商适用的材料证明中列出的所有元素。

3.2 拉伸试验
拉伸试验要满足ASTM A370的最低要求，每一炉号或热处理批号都要检测屈服强度、拉伸强度、伸长率和断面收缩率。

试样应该按照API Spec7-1规定的位置取得。

3.3 Impact Testing
The Charpy ’V’ notch energy level shall be 42 joules (31 ft.lbf.) minimum average of three test specimens tested at room temperature. No individual value shall be less than 32 joules (24 ft.lbf.).
Three longitudinal impact test specimens per heat/heat treatment lot of material shall be taken from at least one (1) inch below the O.D. surface of the material.
3.3 冲击试验
在室温下三组试样的夏比‘V’形槽冲击功的最小平均值应达到42焦耳（31ft.lbf.）。

不允许有单个数值低于32焦耳（24ft.lbf.）。

材料的每一炉号或热处理批号的三组纵向冲击试验试样应该取自材料表面外径下面至少1英寸的位置。

3.4 Hardness Testing
Through thickness hardness verification shall be carried out on the wrought material, applying the sampling basis indicated below. Measurements shall be taken at room temperature on a radial cross section as indicated in Appendix 1.
Pre-heat treated bar stock or mechanical tubing shall have a test specimen taken at least one radius from the end of each bar/tube.
3.4 硬度试验
对于锻造材料应该进行全壁厚的硬度验证，采用下面显示的抽样方法。

在室温下按照附录1显示在径向横截面上进行。

预热处理的棒料和机械加工的管材，至少有一个试样取自每个棒料或管材端面半径上。

When drill collars are rough machined (O.D. and I.D.) prior to final heat treatment, hardness tests shall be carried out on a heat/heat treatment lot basis using a test sample of similar O.D. and I.D. dimensions (taken at a location of max. wall thickness of a rough machined body). The length of the test sample shall be at least equal to the sample O.D. the cross section specimen shall be taken at mid length.
All hardness test results taken on a single cross section shall be within a range of 6 HRC points, with no single value below 30 HRC (285 BHN). The absolute values shall meet the manufacturer’s material specification.
当钻铤在最终热处理之前进行机械粗加工（外圆和内孔）时，每一炉号或热处理批号应该采用类似于外径和内径尺寸的试样（在机械粗加工材料上壁厚最大的位置取样）进行硬度试验。

试样的长度至少应该等于在中部取样的样本橫截面上的样本外径。

在单个橫截面测量的所有硬度试验结果应该在6HRC范围之内，且没有一个单个值低于30 HRC (285 BHN)。

绝对值应该满足制造商的材料规范。

4. DIMENSIONAL INSPECTION (Ref. Sub-Spec. 90.1)
4.1 Drill Collar Bore Concentricity
When boring of the drill collar bar is carried out from both ends, the match point shall be located and checked for eccentricity by means of ultrasonic examination carried out to the manufacturer’s documented procedures. The circumference of the drill collar shall be inspected at the step location.
The variation in wall thickness across the step shall not exceed 1.6 mm (1/16"). Steps within the above acceptance criteria shall be dressed to a smooth finish.
The bore at each end shall be concentric with the centreline, eccentricity shall not exceed 1.6 mm (1/16").
4. 尺寸检验（参考：子规范90.1）
4.1 钻铤内孔的同心度
当钻铤棒料进行两端钻孔时，应该按照制造商的工艺文件通过超声波检测工具对中间接刀台进行定位和偏心度测量。

在台阶位置应该检测钻铤一周。

台阶处壁厚变化不应超过1.6 mm (1/16")。

在上述接收标准范围内台阶应最后加工平滑。

内孔的每端都应该与中心线保持同心，偏心度不超过1.6 mm (1/16")。

4.2 Drill Collar Straightness
Drill collar straightness shall be in accordance with API Spec. 7-1. Deflections of up to 10 mm in 2500 mm (1/2" in 10’) may be corrected by cold pressed straightening with stress relieving at manufacturer’s option.
Deflections of over 10 mm in 2500 mm (1/2" in 10’) shall be corrected by press straightening at 540°C to 570° C (1000°F to 1050°F) followed by stress relieving at the same temperature.
4.2 钻铤的平直度
钻铤的平直度应该符合API Spec 7-1规定。

如果每2500 mm不超过10 mm（或10´不超过1/2"）的偏差，就需要采用制造商选用的具有应力释放功能的冷压校直方法进行校正。

如果每2500 mm超过10 mm（或10´超过1/2"）的偏差，就需要在540°C至570°C（1000°F至1050°F）的温度下配套相同温度下应力释放功能的压力校直方法进行校正。

4.3 Spiral Grooves
Spiral grooving, when applicable, shall be in accordance with the manufacturer’s specification, however, the loss of mass due to spiral grooving shall not be more than 4% of the mass of a cylindrical (slick) drill collar.
4.4 Slip and Elevator Recess
The location and dimensions of the slip and elevator recesses shall be as specified in ISO 10407, latest revision.
4.3 螺旋槽
如果适用，螺旋槽应该按照制造商的规范进行加工，然而由于加工螺旋槽所去除的质量不能超过圆柱（光滑）钻铤质量的4%。

4.4 吊卡瓦槽
吊卡瓦槽的位置和尺寸应该按照ISO 10407最新版的规定。

5. FUNCTIONAL TESTING (Ref. Sub-Spec. 130.1)
Functional testing shall be carried out to the manufacturer’s specifications but shall include as a minimum, a drift test of the bore of each drill collar as per API Spec. 7-1.
5. 功能试验（参考：子规范130.1）
功能试验应该按照制造商的规范进行，但至少应该包括每一支钻铤内孔都应按照API Spec7-1要求进行通径试验。

6. MARKING (Ref. Sub-Spec. 20.3)
6.1 In addition to the marking requirements of API Spec. 7-1, each drill collar shall be provided with a recess located on the O.D. two feet (2 ft) below the rotary box connection.
6.2 The recess shall be stamped in accordance with the requirements of Sub- Spec. 20.3.
6.3 Size of the recess shall be in accordance with API Spec. 7-1.
6. 标识（参考：子规范20.3）
6.1 除了API Spec7-1要求的标识外，每支钻铤应该在旋转内螺纹连接下方两英尺的外径位置加工一个凹槽。

6.2 凹槽内应该按照子规范20.3的要求模印标识。

6.3 凹槽的尺寸应该符合API Spec7-1的要求。

MATRIX
Equipment Name: Drill Collars
Specification: 03.38.10.1110
Manufacturer: General
Model/Type: Various
Material Group: Low Alloy Steel
Service: Non-Sour
引用规范清单
装备名称：钻铤
标准编号：03.38.10.1110
制造厂商：通用
型号类型：所有类型
金属级别：低合金钢
工作范围：非酸性环境
D.C. Cylindrical (Slick)
Class: B, C, D
Material: Wrought Low Alloy Steel
Number Title
10.1 Material Certificates – General
10.2.2 Material Certificates – Assembly Certificate
10.4 Type B Material Test Certificate
20.3 Traceability – Serialization Traceability
20.4 Traceability – Heat/Heat Treatment Lot Traceability
40.1 NDE Surface, General
圆柱（光滑）钻铤
类别： B、C、D
材料锻造低合金钢
编号标题
10.1 材料证明书----通用
10.2.2 材料证明书----组装证明书
10.4 B类材料试验证明书
20.3 可追溯性----序列化可追溯性
20.4 可追溯性----炉号/热处理批的可追溯性
40.1 表面无损探伤，通用
40.6.1.3 Magnetic Particle and Visual Examination (MT + VE) of Threads – Technique – Wet Fluorescent Method
40.6.2.3 Magnetic Particle and Visual Examination (MT + VE) of Threads –Required Extent –One Hundred Percent
40.6.3.3 Magnetic Particle and Visual Examination (MT + VE) of Threads – Acceptance Standard – Relevant Indications
50.1 Detection and Acceptance of Sub-Surface Imperfections – General
50.5.1.2 Ultrasonic Examination (UT) of Forgings/Mech. Tubing/ Barstock (Non-Austenitic Steels) – Technique – Applied Techniques/Conditions
50.5.2.3 Ultrasonic Examination (UT) of Forgings/Mech. Tubing/ Barstock (Non-Austenitic Steels) – Required Extent – One Hundred Percent
50.5.3.2 Ultrasonic Examination (UT) of Forgings/Mech. Tubing/ Barstock (Non-Austenitic Steels) – Acceptance Standard – Acceptable Indications
40.6.1.3 螺纹的磁粉探伤和目视检查（MT+VE）----工艺----湿荧光方法
40.6.2.3 螺纹的磁粉探伤和目视检查（MT+VE）----要求范围----100%
40.6.3.3 螺纹的磁粉探伤和目视检查（MT+VE）----接收标准----相关指标
50.1 浅表面缺陷的检测和接收----通用
50.5.1.2 锻件、机械加工的管材和棒材（非奥氏体钢）的超声波探伤（UT）----工艺----适用工艺条件50.5.2.3 锻件、机械加工的管材和棒材（非奥氏体钢）的超声波探伤（UT）----要求范围----100% 50.5.3.2 锻件、机械加工的管材和棒材（非奥氏体钢）的超声波探伤（UT）----接收标准----相关指标
60.1 Disposition of Defects – Surface Dressing
70.1 Hardness Testing – General
90.1 Dimensional Inspection – General
90.2 Dimensional Inspection – Threads
130.1 Functional Testing – General
150.1 Impact Testing – General
160.1 Non-Conformity Procedure – General
170.1 Boxing/Packing/Marking – General
180.1.3 Quality Documentation for Non-Welded Products
60.1 不合格品的处置----表面修整
70.1 硬度试验----通用
90.1 尺寸检查----通用
90.2 尺寸检查----螺纹
130.1 功能试验---通用
150.1 冲击试验----通用
160.1 不合格品程序----通用
170.1 打包/装箱/标识----通用
180.1.3 非焊接产品的质量文件
D.C. Pup Joint Cylindrical
Class: B, C, D
Material: Wrought Low Alloy Steel
Number Title
10.1 Material Certificates – General
10.2.2 Material Certificates – Assembly Certificate
10.4 Type B Material Test Certificate
20.3 Traceability – Serialization Traceability
20.4 Traceability – Heat/Heat Treatment Lot Traceability
40.1 NDE Surface, General
圆柱（光滑）钻铤短节
类别： B、C、D
材料锻造低合金钢
编号标题
10.1 材料证明书----通用
10.2.2 材料证明书----组装证明书
10.4 B类材料试验证明书
20.3 可追溯性----序列化可追溯性
20.4 可追溯性----炉号/热处理批的可追溯性
40.1 表面无损探伤，通用
40.6.1.3 Magnetic Particle and Visual Examination (MT + VE) of Threads – Technique – Wet Fluorescent Method
40.6.2.3 Magnetic Particle and Visual Examination (MT + VE) of Threads –Required Extent –One Hundred Percent
40.6.3.3 Magnetic Particle and Visual Examination (MT + VE) of Threads – Acceptance Standard – Relevant Indications
50.1 Detection and Acceptance of Sub-Surface Imperfections – General
50.5.1.2 Ultrasonic Examination (UT) of Forgings/Mech. Tubing/ Barstock (Non-Austenitic Steels) – Technique – Applied Techniques/Conditions
50.5.2.3 Ultrasonic Examination (UT) of Forgings/Mech. Tubing/ Barstock (Non-Austenitic Steels) – Required Extent – One Hundred Percent
50.5.3.2 Ultrasonic Examination (UT) of Forgings/Mech. Tubing/ Barstock (Non-Austenitic Steels) – Acceptance Standard – Acceptable Indications
40.6.1.3 螺纹的磁粉探伤和目视检查（MT+VE）----工艺----湿荧光方法
40.6.2.3 螺纹的磁粉探伤和目视检查（MT+VE）----要求范围----100%
40.6.3.3 螺纹的磁粉探伤和目视检查（MT+VE）----接收标准----相关指标
50.1 浅表面缺陷的检测和接收----通用
50.5.1.2 锻件、机械加工的管材和棒材（非奥氏体钢）的超声波探伤（UT）----工艺----适用工艺条件50.5.2.3 锻件、机械加工的管材和棒材（非奥氏体钢）的超声波探伤（UT）----要求范围----100% 50.5.3.2 锻件、机械加工的管材和棒材（非奥氏体钢）的超声波探伤（UT）----接收标准----相关指标
60.1 Disposition of Defects – Surface Dressing
70.1 Hardness Testing – General
90.1 Dimensional Inspection – General
90.2 Dimensional Inspection – Threads
130.1 Functional Testing – General
150.1 Impact Testing – General
160.1 Non-Conformity Procedure – General
170.1 Boxing/Packing/Marking – General
180.1.3 Quality Documentation for Non-Welded Products
60.1 不合格品的处置----表面修整
70.1 硬度试验----通用
90.1 尺寸检查----通用
90.2 尺寸检查----螺纹
130.1 功能试验---通用
150.1 冲击试验----通用
160.1 不合格品程序----通用
170.1 打包/装箱/标识----通用
180.1.3 非焊接产品的质量文件
D.C. with Slip Recess
Class: B, C, D
Material: Wrought Low Alloy Steel
Number Title
10.1 Material Certificates – General
10.2.2 Material Certificates – Assembly Certificate
10.4 Type B Material Test Certificate
20.3 Traceability – Serialization Traceability
20.4 Traceability – Heat/Heat Treatment Lot Traceability
40.1 NDE Surface, General
带卡瓦槽的钻铤
类别： B、C、D
材料锻造低合金钢
编号标题
10.1 材料证明书----通用
10.2.2 材料证明书----组装证明书
10.4 B类材料试验证明书
20.3 可追溯性----序列化可追溯性
20.4 可追溯性----炉号/热处理批的可追溯性
40.1 表面无损探伤，通用
40.6.1.3 Magnetic Particle and Visual Examination (MT + VE) of Threads – Technique – Wet Fluorescent Method
40.6.2.3 Magnetic Particle and Visual Examination (MT + VE) of Threads –Required Extent –One Hundred Percent
40.6.3.3 Magnetic Particle and Visual Examination (MT + VE) of Threads – Acceptance Standard – Relevant Indications
50.1 Detection and Acceptance of Sub-Surface Imperfections – General
50.5.1.2 Ultrasonic Examination (UT) of Forgings/Mech. Tubing/ Barstock (Non-Austenitic Steels) – Technique – Applied Techniques/Conditions
50.5.2.3 Ultrasonic Examination (UT) of Forgings/Mech. Tubing/ Barstock (Non-Austenitic Steels) – Required Extent – One Hundred Percent
50.5.3.2 Ultrasonic Examination (UT) of Forgings/Mech. Tubing/ Barstock (Non-Austenitic Steels) – Acceptance Standard – Acceptable Indications
40.6.1.3 螺纹的磁粉探伤和目视检查（MT+VE）----工艺----湿荧光方法
40.6.2.3 螺纹的磁粉探伤和目视检查（MT+VE）----要求范围----100%
40.6.3.3 螺纹的磁粉探伤和目视检查（MT+VE）----接收标准----相关指标
50.1 浅表面缺陷的检测和接收----通用
50.5.1.2 锻件、机械加工的管材和棒材（非奥氏体钢）的超声波探伤（UT）----工艺----适用工艺条件50.5.2.3 锻件、机械加工的管材和棒材（非奥氏体钢）的超声波探伤（UT）----要求范围----100% 50.5.3.2 锻件、机械加工的管材和棒材（非奥氏体钢）的超声波探伤（UT）----接收标准----相关指标
60.1 Disposition of Defects – Surface Dressing
70.1 Hardness Testing – General
90.1 Dimensional Inspection – General
90.2 Dimensional Inspection – Threads
130.1 Functional Testing – General
150.1 Impact Testing – General
160.1 Non-Conformity Procedure – General
170.1 Boxing/Packing/Marking – General
180.1.3 Quality Documentation for Non-Welded Products
60.1 不合格品的处置----表面修整
70.1 硬度试验----通用
90.1 尺寸检查----通用
90.2 尺寸检查----螺纹
130.1 功能试验---通用
150.1 冲击试验----通用
160.1 不合格品程序----通用
170.1 打包/装箱/标识----通用
180.1.3 非焊接产品的质量文件
D.C. Spiral Grooved
Class: B, C, D
Material: Wrought Low Alloy Steel
Number Title
10.1 Material Certificates – General
10.2.2 Material Certificates – Assembly Certificate
10.4 Type B Material Test Certificate
20.3 Traceability – Serialization Traceability
20.4 Traceability – Heat/Heat Treatment Lot Traceability
40.1 NDE Surface, General
螺旋槽的钻铤
类别： B、C、D
材料锻造低合金钢
编号标题
10.1 材料证明书----通用
10.2.2 材料证明书----组装证明书
10.4 B类材料试验证明书
20.3 可追溯性----序列化可追溯性
20.4 可追溯性----炉号/热处理批的可追溯性
40.1 表面无损探伤，通用
40.6.1.3 Magnetic Particle and Visual Examination (MT + VE) of Threads – Technique – Wet Fluorescent Method
40.6.2.3 Magnetic Particle and Visual Examination (MT + VE) of Threads –Required Extent –One Hundred Percent
40.6.3.3 Magnetic Particle and Visual Examination (MT + VE) of Threads – Acceptance Standard – Relevant Indications
50.1 Detection and Acceptance of Sub-Surface Imperfections – General
50.5.1.2 Ultrasonic Examination (UT) of Forgings/Mech. Tubing/ Barstock (Non-Austenitic Steels) – Technique – Applied Techniques/Conditions
50.5.2.3 Ultrasonic Examination (UT) of Forgings/Mech. Tubing/ Barstock (Non-Austenitic Steels) – Required Extent – One Hundred Percent
50.5.3.2 Ultrasonic Examination (UT) of Forgings/Mech. Tubing/ Barstock (Non-Austenitic Steels) – Acceptance Standard – Acceptable Indications
40.6.1.3 螺纹的磁粉探伤和目视检查（MT+VE）----工艺----湿荧光方法
40.6.2.3 螺纹的磁粉探伤和目视检查（MT+VE）----要求范围----100%
40.6.3.3 螺纹的磁粉探伤和目视检查（MT+VE）----接收标准----相关指标
50.1 浅表面缺陷的检测和接收----通用
50.5.1.2 锻件、机械加工的管材和棒材（非奥氏体钢）的超声波探伤（UT）----工艺----适用工艺条件50.5.2.3 锻件、机械加工的管材和棒材（非奥氏体钢）的超声波探伤（UT）----要求范围----100% 50.5.3.2 锻件、机械加工的管材和棒材（非奥氏体钢）的超声波探伤（UT）----接收标准----相关指标
60.1 Disposition of Defects – Surface Dressing
70.1 Hardness Testing – General
90.1 Dimensional Inspection – General
90.2 Dimensional Inspection – Threads
130.1 Functional Testing – General
150.1 Impact Testing – General
160.1 Non-Conformity Procedure – General
170.1 Boxing/Packing/Marking – General
180.1.3 Quality Documentation for Non-Welded Products
60.1 不合格品的处置----表面修整
70.1 硬度试验----通用
90.1 尺寸检查----通用
90.2 尺寸检查----螺纹
130.1 功能试验---通用
150.1 冲击试验----通用
160.1 不合格品程序----通用
170.1 打包/装箱/标识----通用
180.1.3 非焊接产品的质量文件
D.C. Pup Joint Spiral Grooved
Class: B, C, D
Material: Wrought Low Alloy Steel
Number Title
10.1 Material Certificates – General
10.2.2 Material Certificates – Assembly Certificate
10.4 Type B Material Test Certificate
20.3 Traceability – Serialization Traceability
20.4 Traceability – Heat/Heat Treatment Lot Traceability
40.1 NDE Surface, General
螺旋槽的钻铤短节
类别： B、C、D
材料锻造低合金钢
编号标题
10.1 材料证明书----通用
10.2.2 材料证明书----组装证明书e
10.4 B类材料试验证明书
20.3 可追溯性----序列化可追溯性
20.4 可追溯性----炉号/热处理批的可追溯性
40.1 表面无损探伤，通用
40.6.1.3 Magnetic Particle and Visual Examination (MT + VE) of Threads – Technique – Wet Fluorescent Method
40.6.2.3 Magnetic Particle and Visual Examination (MT + VE) of Threads –Required Extent –One Hundred Percent
40.6.3.3 Magnetic Particle and Visual Examination (MT + VE) of Threads – Acceptance Standard – Relevant Indications
50.1 Detection and Acceptance of Sub-Surface Imperfections – General
50.5.1.2 Ultrasonic Examination (UT) of Forgings/Mech. Tubing/ Barstock (Non-Austenitic Steels) – Technique – Applied Techniques/Conditions
50.5.2.3 Ultrasonic Examination (UT) of Forgings/Mech. Tubing/ Barstock (Non-Austenitic Steels) – Required Extent – One Hundred Percent
50.5.3.2 Ultrasonic Examination (UT) of Forgings/Mech. Tubing/ Barstock (Non-Austenitic Steels) – Acceptance Standard – Acceptable Indications
40.6.1.3 螺纹的磁粉探伤和目视检查（MT+VE）----工艺----湿荧光方法
40.6.2.3 螺纹的磁粉探伤和目视检查（MT+VE）----要求范围----100%
40.6.3.3 螺纹的磁粉探伤和目视检查（MT+VE）----接收标准----相关指标
50.1 浅表面缺陷的检测和接收----通用
50.5.1.2 锻件、机械加工的管材和棒材（非奥氏体钢）的超声波探伤（UT）----工艺----适用工艺条件50.5.2.3 锻件、机械加工的管材和棒材（非奥氏体钢）的超声波探伤（UT）----要求范围----100% 50.5.3.2 锻件、机械加工的管材和棒材（非奥氏体钢）的超声波探伤（UT）----接收标准----相关指标
60.1 Disposition of Defects – Surface Dressing
70.1 Hardness Testing – General
90.1 Dimensional Inspection – General
90.2 Dimensional Inspection – Threads
130.1 Functional Testing – General
150.1 Impact Testing – General
160.1 Non-Conformity Procedure – General
170.1 Boxing/Packing/Marking – General
180.1.3 Quality Documentation for Non-Welded Products
60.1 不合格品的处置----表面修整
70.1 硬度试验----通用
90.1 尺寸检查----通用
90.2 尺寸检查----螺纹
130.1 功能试验---通用
150.1 冲击试验----通用
160.1 不合格品程序----通用
170.1 打包/装箱/标识----通用
180.1.3 非焊接产品的质量文件
Appendices
附录
Appendix 1
附录 1
全壁厚材料验证的硬度试验位置
附录 2。