轧钢英语大全

合集下载

轧钢专业词汇表

轧钢专业词汇表一、首钢京唐（酸轧机组）常用词1.entry W/B conveyor 入口步进梁运输机2. entry coil turner 旋转台3.entry coil car 入口钢卷车4.pay off reel 开卷机5.processor 处理器6.coll opener 开卷器7.ertry shear with pinch roll 入口剪带夹送辊8.scrap disposal equipment 废料处理装置9.deflector pinch roll 转向夹送辊10. deflector roll 转向辊11.welder 焊机12.notcher 月牙剪13.side guide 边部对中14.bridle roll 张力辊15.steering roll 纠偏辊16.tension meter roll 张力计辊17.tension leveller 拉伸破磷机18.entry wringer roll 入口挤干辊19.dryer 干燥器20.side notcher 月牙剪21.hold down roll 压辊22.side trimmer 切边剪23.scrap chopper 碎边剪24.scrap conveyor 废料运输带25.burr masher 去毛刺机l 轧机2l motor 轧机主电机28.rotary shear 飞剪29.carrousel reel 张力卷取机30.inspection table 检查台31.sleeve bucket transfer car 套筒运输车32.delivery coil conveyor 出口步进梁运输机33.skid 鞍座34.nozzle 喷嘴二、浙江东南1. Reversing Cold Mill RCM 可逆式冷轧机2. Motor Control Center MCC 电机控制中心3. E-house 电器室4. transformer 变压器5. skin pass mill 或temper mill 平整机6. product mix 产品大纲7.coil weight 卷重8. stack weight 垛重9. workbase 炉台10. Specific coil weight 卷材单重11. inner cover 内罩12. heating bell 加热罩13. cooling bell 冷却罩14. filter mesh 过滤器网15. pressure switch 压力开关16. isolating unit 隔离装置17. control relay 控制继电器18. emulsion room 乳化液站19. combustion 燃烧20. butterfly valve 蝶形阀21. Safety Equipment 安全设备22. roll chock 轴承座23. Spraying header 喷淋水管（喷淋头）24. Mill stand piping 轧机机座管系管线25. Drive spindles 驱动轴26. Cross cut shear 横剪机组27. Pivot 枢轴28. Coil car 卷材移动台车29. Segments （胀缩式卷筒）扇形体30. Snubber roll 缓冲辊31. Groove 凹槽32. flange 法兰33. Shape Measuring Roll 板形仪34. Delivery entryTension Reel 出入口卷取机35. Foundation Bolts and Nuts 基础螺栓36. Interconnecting piping 中间管线37. Gear Coupling 齿轮联轴器38. Load test 负载测试39. Breakage 断带40. Stoppage 停车cold rolled: 冷轧的冷态滚压的coating section:涂镀断面cold rolled steel sheet: 冷轧薄钢板welding: 焊接cold rolled coil : 冷轧薄卷scale breaker: 除鳞机铁皮清除机electrical steel sheet: 电工钢（片）heat treating furnace: 热处理炉uncoiler: 开卷机minimize spangle: 微化晶粒reheating furnace: 再加热炉coating bath: 镀槽cold leveling: 冷平整，冷矫正air cooling: 空气冷却pickling: 酸洗water cooling: 水冷却cold rolling mill: 冷轧机leveling: 矫正平整electrolytic cleaner: 电解清洗液Hot-dip galvanized steel strip: 热浸镀锌钢preheating: 预热带（卷）soaking cooling: 均匀退热Electrolytic cleaning：电解处理rapid cooling: 快速冷却Electrolytic cleaner：电解清洗液over aging: 过时效老化过度final cooling: 最后冷却reheating furnace：重热熔炉continuous annealing line：连续退火线crack：裂化recoiling：重绕temper rolling：斜坡轧制，硬化冷轧表面temper rolling: 硬化冷轧表面光轧平整光轧平整batch annealing line: 成批退火线Coil preparation line：成卷预热线cold rolled coil: 冷轧薄板Over aging ：过时效老化过度side trimming: 切侧边final cooling：最后冷却shearing line: 剪切线tandam cold rolling：拉锯冷轧cold rolled sheet: 冷轧薄板Trimmer 切边机pay off reel：松卷机Skinpass：表皮光轧shearer：剪切机剪断机delivery looper：传送活套entry looper: 进口活套BP coil：镀锡原板tension leveler：张力平整机Heating area:加热区Furnace：加热炉Bend：弯曲Gas：煤气Combust：燃烧Mixed gas：混合煤气Temperature：温度Nitrogen：氮气Centigrade degree：摄氏度Oxygen：氧气Pyrometer ：高温计Resident oxygen：炉内残氧Thermocouples：热电偶Pressure：压力Fixed beam：固定梁Vol ume：体积、流量Walking beam：步进梁Valve ：阀门Forward：向前Slab：板坯Backward：向后Slab yard：板坯库Discard：剔除Continuous cast slab：连铸板坯Discard table：剔除辊道Width：宽度Charge：装炉Thickness：厚度Discharge：出炉Length：长度Preheating zone：预热区Weight：重量Heating one：加热区Soaking zone：均热区Discharge machine：出钢机Vaporizing cooling/ vapor cooling：气化冷Compressed air 压缩空气却Burner 烧嘴Soft water：软水Combustion air fan 助燃风机Scale：氧化铁皮Recuperative 有恢复力的Ventilate：通风heat exchanger 回热式热交换器Chimney：烟囱Refractory brick 耐火砖Exhaust：废气Mathematic model 数学模型Stack：烟道Feed-forward 前馈Roller able：辊道Feedback 反馈Baffle：挡板Furnace pressure 炉压Charge machine：装钢机Temperature profile 温度曲线Hot rolling shop：热轧车间Mill 轧机Spindle 接轴4-high finishing mill 四辊精轧机Universal Spindle 万向接轴Rough mill 粗轧Shaft 轴Screw down 压下Roll changing device 换辊装置Screw up 抬升辊缝Crane 行车Edger 立辊轧机，轧边机Bite 咬入High-pressure descaling system 高压水除Cascade speed adjustment 串联调速鳞系统Cobble 堆钢事故，中间事故坯料Nozzle 喷嘴Tension 张力Heat cover 保温罩Tension control 张力控制Shear 剪机Loop height 活套量/活套高度Hydraulic loop 液压活套Speed up 升速Looper 活套Lock cylinder 锁紧缸Side guide 侧导卫Balance cylinder 平衡缸Interstand cooling 机架间冷却Lift 提升Run-out table 精轧输出辊道Shift 横移Laminar cooling 层流冷却Leveling 校平，调平Head water tank 高位水箱Zero 校零Side stripper 侧喷头Alignment 对中Pinch roll 夹送辊Industrial water 循环水Down Coiler 卷取机Water volume 水量Mandrel 卷取机芯轴Water pressure水压Wrapper roller 助卷辊Cooling r ate 冷却速度Coil stripper car 卸卷小车Speed cone 速度锥Strip catcher 卷取区域带钢拦截装置Maintenance 检修，维护Gear motor 齿轮马达Pneumatic system 气动系统Coupling 接手，连接器Roll shop 轧辊间Roll 轧辊Work roll 工作辊Grinder 磨床Back-up roll 支撑辊Work roll grinder 工作辊磨床Barrel 辊身Combinative/universal grinder 组合磨床Roll neck 辊颈Roll cooling 轧辊冷却Vertical 垂直的Work roll chock 工作辊轴承座Calibration 校准，刻度Work roll bending system 工作辊弯辊系统Compensation 补偿Work roll shifting system 工作辊窜辊系统Correction 纠正Back-up roll chock 支撑辊轴承座Control panel 控制面板，操作控制台Bearing 轴承Deviation 偏差Work roll bearing 工作辊轴承Error 误差，错误Oil film bearing/morgoil bearing 油膜轴承Offset 偏差量Headstock 头架Definition 定义Tailstock 尾架Reverse 反转Grinding carriage 磨头滑架Swivel 回转，转动Wheel 砂轮Distance 距离Dressing diamond 修整金刚石Range 范围Measure 测量Chamfer 凸度Diameter 直径Centerline 中心线Ovality 不圆度Infeed mode 进给模式Roundness 圆度Limit 限制，极限Eccentricity 偏心度Limit switch 限位开关Contour 外形轮廓Scan 扫描Geometry 几何尺寸，几何形状Coolant 冷却剂Curve 曲线Surface 表面Sine curve 正弦曲线Plunge grinding 掏沟磨削Active curve 实际曲线Caliper 测量卡规Rated curve 额定曲线/设定的曲线Optimize 优化Position 位置Load roll 装辊Axis 轴，数轴Unload roll 卸辊Horizontal 水平的Calibrate caliper 校准测量卡规Finishing area 精整区域Coil marking machine 钢卷标号机Walking beam transfer 步进梁运输机Coil strapping machine 钢卷打捆机Coil yard 钢卷库Coil weighing device 钢卷称重装置Skin pass 平整机Sampling shear 取样剪Saddle 鞍座Transfer chain 链条运输机Electric room 电气室Motor 电机Process computer 过程计算机Main motor 主电机Program 程序，编程Load 载荷PLC：programmable logic controller 可编Over load 过载程控制器Motor load 电机负荷Encoder 编码器Rolling force 轧制力Information 信息Rolling speed 轧制速度Ghost rolling 模拟轧制MPM: meter per minute 米/分钟Measuring instrument 测量仪表Torque 扭矩X-ray X 射线Rated torque 额定扭矩Thickness gauge 测厚仪Voltage 电压Width gauge 测宽仪HMD: hot material detector 热金属探测仪Emergency 紧急，急停CMD: cold material detector 冷金属探测仪Joggle 点动Light barrier 光栅HMI：human machine interface 人机界面Automatic model 自动模式AC frequency converter 交流变频器Semi-auto model 半自动模式I/O：input/output 输入/输出端口Manual model 手动模式Step control 卷取机助卷辊的“踏步”控制Hydraulic system 液压系统Grease 甘油Pump 泵Oil station 油站Screw pump 螺杆泵SSC: Short stroke control 短行程控制Filter 过滤器，滤网AGC: automatic gauge control 自动压下Cylinder 液压缸，圆柱体控制Valve stand 阀台AWC: automatic width control 自动宽度Accumulator 蓄能器控制Leakage 泄漏Product 产品Grade 钢种Ferrite 铁素体Batch 一炉，一批Pearlite 珠光体Batch No. 炉批号Deep drawn 深冲Coil 钢卷SPHC 普通级热轧钢板（卷）Strip 带钢，薄带钢SPHD 深冲级热轧钢板（卷）Sheet 钢板，薄钢板SPCC 普通级冷轧钢板（卷）Plate 中厚板SPCD 深冲级冷轧钢板（卷Physical performance 物理性能High strength low-alloy steel 低合金高强Mechanical performance 机械性能度钢Strength 强度Silicon steel 硅钢，电工钢Elongation 延伸Galvanizing 镀锌Flatness 平直度Coating 涂镀，涂层Plasticity 塑性Heat treatment 热处理Crown/chamber 凸度Aging 时效处理Hardness 硬度Annealing 退火Microstructure 微观组织结构Quenching 淬火Austenite 奥氏体Alarm 报警Radioactive hazard 放射性伤害Anchoring bolt 地脚螺栓Caution 注意，小心Yield 产量，成材率Layout 平面布置Ton 吨Document 文件Annual 一年的Documentation 技术文本，技术文件报价Shift 班书Safety 安全TOP: take-over poi n t 交接点耐磨性abrasive碰撞仪butt gauge气孔abscess计算calculation横坐标abscissa凸轮cam容纳、收纳accommodating曲线度cambering amount空气喷射air ejection辊型误差cambering profile气动电机air motor悬梁cantilever自动踏步控制AJCautomatic jumping有能力的capablecontrol能力capacity定中心、对中align渗碳carburized排成直线、列队、对中alignment小车，砂轮架carriage交替、轮流alternate延伸辊道carry over table电流量amperage连铸坯分段剪CC shear锚固、地脚anchor中心线centerline退火的annealed离心机centrifuge一年一次的annual房间chamber能应用的、适用的、适合的applicable 轴承座chock应用application垫板choke liner增多，重视appreciateC 形沟C-hook接近、进给approach溜槽chute适合的、特有的appropriate圆周运动circular motion裙板apron过滤设备clean-up device相变arrest间隙clearance装配、组装、配件assembly废钢收集装置cobble catcher分配assignment带卷打捆机coil banding machine奥氏体austenite带卷运输机coil conveyor奥氏体轧制austenite rolling带卷检查线coil inspection line 奥氏体的austenitic带卷提升机coil lifter辅助液压auxiliary hydraulic托卷臂coil loading arm轴向的axial带卷打号机coil marking machine 后退、退回backlash开卷机coil opener平衡力balance force带卷鞍座coil saddle球面丝杆ball jack screw带卷鞍座coil skid包装带分配器banding dispenser 带卷站coil station打捆带banding strap卸卷小车coil stripper car冷却段bank带卷回转台coil turner轴承架bearing bracket带卷称重装置coil weighter轴承箱bearing ca.。

轧钢专业英语必备词汇[1]1

(5)轧钢Rolling八辊轧机MKW mill 板坯slab 半连续热带轧机semi-continuous hot-strip mill 薄板sheet 薄板轧机sheet mill 保温炉heat holding furnace 扁锭slab i ngot, slab 扁钢flat bar 不可逆轧机non-reversing mill 步进梁式加热炉walki ng beam type furnace 槽钢channel 车底式加热炉car bottom furnace 车轮轧机railway-wheel mill 车丝机threading machine 成卷coiling 成品包装跨packing bay 初轧机blooming mill 初轧坯翻转装置bloom turnover device 出料拉杆kick-out arm 穿孔机piercing mill 粗轧机rough mill 淬火炉harde ning furnace 搭接炉焊管机lap-welded pipe mill 打包用带钢轧机package mill 打捆机bundle machine 打捆机bundler 打印台stamping station 大型型钢轧机heavy section mill 导辊装置roller guide 地上卷取机up coiler 地下卷取机down coiler 地下卷取机down coiler 地下油库oil cellar 地下运输机t unnel conveyer 叠板轧机pack mill 定径机sizing mill 定心机centering mac hine 镀槽coating bath 镀锡板tinning sheet 镀锡槽tinning bath 镀锡线tinn ing line 镀锌板galvanized sheet 镀锌槽galvanizing bath 镀锌线galvanizin g line 堆储跨storage bay 堆垛机piler 钝化处理passivation 多辊矫直机mu lti-roll straightening machine 方钢square bar 方坯bloom 非连续性轧机no n-continuous rolling mill 飞锯flying saw 干燥台drying station 钢坯, 小方坯billet 钢坯库billet store 钢坯修磨conditioning 高速线材轧机high speed wi re rod mill 高压水除鳞hydraulic jet descaler 工字钢I-bar 工字钢轧机I-bea m mill 工作辊换辊装置work roll changer 工作辊支撑装置work roller suppo rting apparatus 钩式运输机hook transfer 光亮退火炉bright annealing furn ace 轨梁轧机rail-beam section mill 滚筒剪drum type shear 横切机transv ersal shear 厚板heavy plate 厚板轧机heavy plate mill 环形加热炉rotary hearth furnace 换辊小车roll change carriage 荒管, 毛管, 空心坯pierced bi llet, hollow billet 回火炉tempering furnace 回转剪rotary cropping shear 活套loop 活套张紧辊bridle roll 机后输出辊道mill run-out table 机架, 牌坊stand, housing 机架辊breast roll 机前输入辊道mill run-in table 挤压机ex truder 夹送辊deflector pinch roll 加热炉heating furnace 碱槽alkaline bath 剪切跨shear bay 减径机reducing mill 矫直机straightening machine, stra ightening mill 角钢angle steel 揭盖机cover carriage 紧卷tight coil 进料拉杆kick-in arm 浸镀immersion coating 井式炉pit batch type furnace 精轧机finish mill 精整加工线finishing machine 精整跨finishing bay 卷材, 线卷coil 均热炉pit furnace 均热炉跨soaking pit bay 均整机,整径机(管) reeling machine 开卷机, 拆卷机decoiler 开坯机cogging mill 可逆辊道reversing t able 空心坯减径机shell-reducing mill 拉丝机wire-drawing machine 扩径机(管) repiercing machine 冷床cold bed 冷锯cold saw 冷轧板带钢cold rolle d strip 立辊vertical roll 连续式加热炉continuous type furnace 连续酸洗co ntinuous acid-washing 链式运输机chain transfer 磷化处理phosphate treat ment 磷酸phosphoric acid 硫酸sulfurous acid 炉卷机steckel mill炉用卷取机furnace coiler 轮箍轧机tyre mill 内表修磨inside grinding 拧接头机coupling applicator 盘条rod coil 平立(万能)轧机horizontal-vertical (H V) mill 平整机temper machine 破鳞辊descaling roll 破鳞机scale breaker, descaler 切边side crops 切边剪end trimming shear 切头top crops 切头剪end shear 切尾end crops 去刺机deburring machine 热处理heat treat ment 热带轧机hot-strip mill 热镀hot-dip coating 热锯hot saw 热轧板带钢hot rolled strip 乳化液emulsion 森吉米尔轧机Sendzimir mill 上料台架ingo ing skid 深冲薄钢板deep drawing sheet 石油管套管pipe case 收集台coll ecting table 受料辊道receiving table 输出辊道run-out table 输入辊道run-i n table 水力除鳞hydraulic descaler 水压试验机hydraulic pressure tester 酸槽acid bath 酸洗槽pickling bath 酸洗工段pickling department 酸洗机pi ckling machine 酸洗线pickling line 酸洗用酸acid for pickling 甩尾back-en d whip 丝扣保护套thread protector 四机架连续式带钢冷轧机four-stand ten dem cold strip mill 松卷loose coil 碎断剪chopping shear 塔式酸洗机towe r pickler 套管接头pipe coupling 铁皮坑scale pit 通径机drifter 筒式卷取机drum type coiler 涂漆装置painting unit 吐丝机laying head 推钢机, 推杆p usher 拖运机,移送机dragging device 脱脂槽degreasing bath 外表修磨out side grinding 弯辊装置bending-up roll device 万向连轴节universal spindlecoupling 无扭轧机non-twist mill 无损探伤non destoryed test 铣头机cha mfering machine 限动芯棒轧管机retained mandrel pipe mill 硝酸nitric aci d 小型型钢轧机light section mill, merchant bar mill 芯棒式轧管机mandrel mill 型钢, 条钢bar 行星轧机planetary rolling mill 修磨机grinder 压下螺丝screw down 压下装置, 压下机构screwdown 延伸机elongator 硬度试验机hardness tester 油膜轴承oil film lubrication bearing 预精轧机pre-finishing mill 预热炉preheating furnace 圆锭round ingot, round billet 圆钢round b ar 圆盘锯circular saw 运锭车, 翻锭车ingot buggy 运输辊道processing ta ble 再加热炉reheating furnace 轧边机, 立辊轧机edger 轧钢rolling 轧钢车间rolling plant 轧管机设备tube mill equipment 轧辊及辊道roller and tabl e 轧辊压下装置roller press-down device 轧辊轴承座roll bearing chock 轧辊支架roll support 轧机rolling mill 轧机传动装置rolling mill drive devic e 轧机跨mill bay, mill aisle 轧机输出辊道mill delivery table 轧机输入辊道mill approach table 窄带strip 张力减径机(管) tension-reducing machine张力控制tension control 罩式炉bell type furnace 支撑辊back-up roll 中板轧机medium plate mill 中厚板medium plate 中间辊道intermediate table 中型宽带轧机medium wide-strip mill 中型型钢轧机medium section mill 中轧机intermediate mill 周期式轧管机pilger mill 转盘turntable 自动轧管机plug mill 纵切机longitudinal shear, slitting shear。

轧钢专业词汇

(1)烧结Sintering抽风机 drawing fan, exhausting fan除尘集灰斗dust hopper除尘设备dedusting equipment带式焙烧机travelling grate ( induration ) machine 带式烧结机continuous-strand sinter machine点火器igniter垫底料给料机bedding burden feeder多管除尘器multi-type deduster二次混料机secondary mixing machine返矿仓 return ore bunker废品率 reject rate粉矿 fines富矿 rich ore鼓风机blower含铁品位grade of iron合格率 percent of pass合格烧结矿qualified sinter回转窑rotary kiln混合料仓mixing bunker混合料给料机mixed burden feeder碱度basicity焦末 nut coke, coke breeze精矿粉 concentrate fines链蓖机 grate, chain-type grate炉尘 dust盘式烧结机 batch-type sinter machine 破碎机 breaker球团 pellet球团矿pellet燃料 fuel material燃烧器burner熔剂 flux筛分设备 screening equipment烧结 sintering烧结车间 sintering plant烧结矿 sinter烧结矿返矿率sinter return ratio烧结矿品位 grade of sinter生球 fresh ( green ) pellet石灰石limestone熟料 clinker竖炉 shaft furnace台车 pallet无烟煤 anthracite, anthracitic coal压块 briquette氧化铁皮 scale萤石 fluorite圆盘给料机 disk-type feeder圆盘造球机disc-type pelletizing machine 圆筒造球机cylinderical pelletizer造球机 pelletizer, pelletizing machine转鼓指数 drum index自熔性烧结矿 self-fluxing sinter作业率 operability(2)焦化及耐火Coking and refractory氨 ammonia氨工段ammonia plant耙焦机 coke-drawing machine白云石 dolomite白云石砖dolomite brick苯 benzole肥煤 fat coal, bituminous coal副产品by product干熄煤机dry quenching machine 高铝砖 alumina brick铬镁砖 chromo-magnesite brick 铬砖 chromite brick硅石 silica灰粉ash content挥发物 volatiles, volatimeter焦化厂coking plant焦炉 coke oven焦炉煤气coke oven gas焦煤 coking coal焦炭转鼓试验coke drum test焦油 tar抗渣性 slag resistance炼焦 coking炼焦炉组coke oven buttery晾焦台 wharf炉门框 door frame铝镁砖aluminium镁石magnesite镁砖magnesia brick磨煤机 coal pulverizer耐火材料refractory material耐火度refractoriness耐火粘土refractory clay, fire clay配煤mixing coal平煤机 coal levelling machine启炉门机 door-extracting machine气孔率 porosity气煤gas coal, bottle coal轻质膨胀粘土骨料light weight expanded clay aggregate 燃烧室 combustion chamber瘦煤 carbonaceous coal碳砖 carbon brick炭化室(炉孔) co oven推焦杆 pushing ram脱苯塔 benzole scrubber熄焦机coke quenching machine洗氨塔ammonia scrubber洗氨塔ammonia washer洗煤 washed coal洗萘塔naphthalene scrubber烟煤 bituminous coal, bituminite粘土砖 chamotte brick装煤孔 coal charging hole(3)炼铁Ironmaking白云石 dolomite崩料,坐料slipping布料器 distributor称量车 weighing car出铁场 casting house 出铁沟 tapping channel出铁口iron notch, taphole出铁口喷火blowing on taphole出渣沟吹慢风磁铁矿大料钟slagging channel slack-wind blowing magnetitelarge bell低品位矿石low grade ore电动泥炮motor operated mud gun 电子秤electronic weigher吊挂保护板hanging protective plate 堵铁口机taphole stopping machine 放灰阀dust discharging valve废气总管waste gas main duct风口 tuyere风口大套 tuyere-cooler casing风口管blast pipe风口镜 tuyere glass风口弯管 penstock damper风量 blast volume风量控制器blast volume controller 风速 blast velocity富矿rich ore, premiun ore高炉blast furnace高炉鼓风机blast furnace blower高炉骨架 frame of furnace高炉利用系数utilization coefficient 高炉煤气BF gas高炉外壳shell of furnace高品位烧结矿high grade sintered ore高压炉顶high pressure on top格砖 checker brick鼓风机站blower station褐铁矿brown iron ore换热式热风炉intermittent stove荒煤气 crude gas黄铁矿, 赤铁矿hematite混风阀mixed air valve计划休风 scheduled down-time焦比 coke ratio焦炭 coke紧急休风emergency blowing-down 静电除尘器electrostatic precipitator 卷扬机室hoist room均压阀 equalizer valve开铁口机 tapper, tapping machine 块矿 briquette块矿 lump ore矿槽 bunker矿粉 fine ore冷风阀cold blast valve冷风阀 cooled blast valve冷风总管cooled blast main duct冷却水箱cooling water box立式冷却壁cooling stave料车 skip料车 skip car料线,料面高度 stockline料钟 bell料柱 stock column硫酸渣purple ore炉衬linings炉底bottom炉顶 top炉顶卷扬机 top hoist炉顶平台 top platform炉顶温度 top temperature炉顶压力top pressure炉腹 bosh炉缸hearth炉缸压力hearth pressure炉喉(护)板stock line armor炉喉 throat炉况不顺blast wandering炉前工, 高炉工人 blast furnace operator 炉身 stack炉身冷却壁stock cooling plate炉腰 waist, straight section螺旋推进式泥炮spiral type clay gun慢风 slow-wind blowing煤气调节阀gas regulating valve煤气阀 gas valve煤气放散阀bleeder valve煤气换向阀gas reversing valve煤气净化gas cleaning (purifying)煤气总管main gas duct泥炮mud ( clay ) gun 泥炮mud, clay皮带秤 belt scale皮带运输机belt conveyer撇渣器 skimmer贫矿lean, low grade ore砌体 brickwork气缸式泥炮 cylinder type clay gun 切断闸板cut-off damper球团矿燃烧器燃烧室热风阀热风阀热风炉pelletburnercombustion chamber hot blast valvehot blast valvestove热风炉交叉并联透风staggered parallel blowing 热风围管hot blast circular duct热风温度hot blast temperature热风总管hot blast main duct熔剂 flux上升管烧结矿石灰石水冲渣双料钟死铁层uptake duct sinterlime stone granulation double bell old horse探尺,料尺 stock rod探尺卷扬机stock rod winch 铁精矿 concentrate铁矿石iron ore铁水罐hot metal ladle铁水罐车hot metal ladle car铁渣比iron and slag ratio透风期on blast透平发电机turbo-generator透平鼓风机 turbo-blower外燃式热风炉external combustion type stove 外燃室external combustion chamber文氏管洗涤器 venturi scrubber无料钟炉顶bell-less top下降管downcomer duct小料钟small bell斜桥skip bridge, hoist bridge休风blowing-down休风率 downtime percentage蓄热式热风炉,考伯式热风炉cowper stove蓄热室 checker chamber旋风除尘器 cyclone旋转布料器rotary burden distributor烟道阀 duct damper移动保护板movable protective plate有效利用系数productivity coefficient有效面积 effective volume鱼雷式铁水罐 torpedo ladle鱼雷式铁水罐车torpedo ladle car造渣 slag-making造渣厂富氧鼓风oxygen-enriched blast造渣填加剂slag-making addition渣场 slag yard渣罐 slag pot, slag ladle渣罐车slag pot car渣罐车备用停车线slag tapping stand-by track 渣坑slag pocket, slag pit渣口, 出渣口slag notch渣口slag notch, cinder notch渣口大套slag notch cooler渣口喷火blowing on the monkey渣口水箱monkey jacket渣口小套, 小渣口monkey渣口小套slag (notch) tuyere渣盘slag pan整粒矿石sized ore重力除尘器gravity dust collector主沟main channel柱塞式泥炮plunger type clay gun铸铁机pig moulding machine铸铁块, 锭pig ingot装料漏斗charging hopper自熔性矿石self-fluxing ore(4)炼钢Steelmaking奥式体钢austenitic steel八角钢材octagon bar白云石dolomite板坯连铸机slab casting machine半封闭型电炉semi-closed type EAF保护渣slag powder补炉机fettling machine不锈钢stainless steel敞开固定型电炉open stationary type EAF敞开回转型电炉open rotating type EAF敞开斜动型电炉open tilting type EAF超低头方坯连铸机extra low head caster(ELH)for bloom , super low head caster ( SLH )超高功率电炉UHP electrical furnace车屑chip车铸bogie (buggy,car) casting称量weighing出钢tapping出铁盘tapping pan出渣slagging除渣器deslagger储槽storage bunker吹氧转炉basic oxygen furnace打印机stamping machine大密封罩, 狗窝dog house带卷strip coil带型连铸机belt type CCM单炉浇铸batch cast捣固料ramming compound捣糊pound to paste捣炉机stoking machine底吹氧气转炉bottom bloom oxygen converter底注, 下注uphill casting, uphill teeming底电极bottom electrode地下料仓underground bunker电极electrode电极压放slip, slipping电极接长系统electrode jointing system电极把持器electrode holder电极柱electrode mast电极糊electrode paste电极套壳electrode casing电极压放装置electrode slipping device电炉electrical arc-furnace (EAF)电炉钢electric arc furnace (EAF) steel顶吹氧气转炉top bloom oxygen converter顶底复合吹转炉top and bottom com bined blown converter多流连铸机multi-strand CCM多炉连铸continuous continuous casting二次精炼secondary refining矾土, 氧化铝alumina方坯连铸机billet cast machine非铁合金non ferro-alloy废钢scrap废钢跨scrap bay废铁iron scrap沸腾钢unkilled steel分类料仓classification bin封闭固定型电炉closed stationary type EAF封闭回转型电炉closed rotating type EAF付枪, 付氧枪sublance负偏差negative deviation富氧鼓风oxygen-enriched blowing钢包, 盛钢桶ladle钢包加热炉ladle heating furnace 钢包旋转台turret, ladle turnable钢锭ingot钢锭模ingot mould钢筋reinforcing bar, rebar钢坯清理间billet conditioning yard钢种kinds of steel高位料仓overhead bunker高压炉顶high pressure top铬铁ferro-chromium给料feeding工具钢tool steel工业纯铁armco-iron鼓肚bulging固定碳fix carbon content硅锰合金silicon manganese alloy硅铁ferro-silicon合金钢alloy steel化学成份chemical composition弧型连铸机bow type CCM滑动水口slide gate还原剂reductant还原剂reduction agent, reductant灰份ash挥发物volatile混料mixed material混铁炉mixer火焰切割机torch cutting machine火焰清理flame deseaming, hot scarfing 夹杂物impurity加料管chargingchute碱性渣basic slag结构钢structural steel结晶器mould, crystalliser焦比specific coke rate焦炭coke交流电弧炉AC electrical arc furnace 浇铸吊车casting crane浇铸机casting machine浇铸坑casting pit浇铸平台casting 浇铸周期casting 浇注casting浇注teeming platform cycle浇注底板pouring bottom plate金属硅silicon metal浸入式水口submerged nozzle开浇cast-on开铁口机open hole machine可浇注性castability可逆皮带运输机reverse belt conveyer 坑铸pit-casting孔型设计groove design矿石mineral拉矫机straightening and withdrawalmachine拉坯机withdrawal device冷轧带卷cold-rolled coil冷轧钢cold-rolled steel立弯型连铸机vertical type CCM, straight mouldbent run-out plant粒度grain size连铸continuous casting连铸机continuous casting machine- CCM 溜槽,溜管chute硫印sulphur print六角钢材hexahedral bar炉壁结瘤wall accretion炉衬furnace lining炉顶料仓top bin炉盖furnace cover炉缸结瘤hearth accretion炉龄campaign炉体furnace body炉子跨furnace bay漏钢breakout铝块aluminium block马式体钢Martensitic steel埋弧电炉submerged electric furnace煤粉pulverized coal锰铁ferro-manganese磨煤机coal pulverizer模铸mold casting木材timber木片wood chip镍铁ferro-nickel喷煤coal injection偏差deviation平炉open hearth furnace(OHF)平炉钢open hearth furnace (OHF) steel 破碎 crush全连铸sequence casting热轧带卷hot-rolled coil热轧钢hot-rolled steel熔剂 flux塞棒 stopper rod筛分 screen筛分机 screen烧结锰矿sintered manganese ore渗碳 carbon penetration生铁 pig iron石灰石lime stone石英 quartz石墨电极 graphitized electrode竖炉, 竖式电炉 shaft electrical arc furnace 酸性渣 acidic slag双壳电炉twin-shell electrical arc furnace 顺行 smooth working四流连铸机four-strand CCM碳化钙 calcium carbide碳素钢 carbon steel碳素电极carbon electrode炭砖charcoal brick特殊钢 special steel铜瓦 copper content element添加剂 additive铁合金 ferro-alloy脱锭机, 脱模机 ingot stripper脱磷 dephosphorise脱硫 desulphurise脱气 degassing脱气剂 degassing agent脱碳 decarburization脱氧 deoxidising脱引锭杆装置 dummy bar disconnection device 弯曲辊bending roll弯曲应力bending stress弯曲装置bending device无烟煤,白煤bituminite下降烟罩操作法declined hood operation process 休风率 downtime ratio悬挂支架suspension frame旋转浇铸台rotating casting table压下率screw-down rate氩氧脱碳argon-oxygen decarburization ACD氧枪 oxygen lance冶炼设备melting equipment冶炼周期tap-to-tap cycle一炉钢 one heat steel乙炔切割acetylene cutting异型钢材shapped bar引锭杆 dummy bar引锭杆架 dummy bar tilter引锭杆坑dummy bar pit引锭杆头dummy bar head萤石 fluorite优质钢high-grade steel有效容积 effective volume鱼尾板splice bar原料 raw material原料跨raw material bay增碳 carburize渣罐 cinder pot渣铁比 slag rate轧辊孔型设计roll pass design轧屑mill scale轧制道次pass轧制周期rolling cycle真空电弧精炼vacuum arc refining VAR真空脱气vacuum arc degassing VAD振动管运输机vibrating pipe conveyer镇静钢 killed steel正偏差positive deviation支架辊back-up roll, supporting roll直流电弧炉DC electrical arc furnace中间罐 tundish中间料仓intermediate bin中心铸管, 塞棒袖砖 central pouring pipe, sleeve brick 珠光体钢pearlite steel铸模 casting mould铸坯导辊strand guide roller转炉钢 basic oxygen converter steel,basic oxygen furnace (BOF) steel自耗电极consumable electrode自焙电极self-baked electrode综合冶炼强度comprehensive rate of driving足辊 foot roll钻孔机 driller(5)轧钢Rolling八辊轧机MKW mill板坯 slab半连续热带轧机semi-continuous hot-strip mill薄板 sheet薄板轧机sheet mill保温炉heat holding furnace扁锭 slab ingot, slab扁钢 flat bar不可逆轧机non-reversing mill步进梁式加热炉walking beam type furnace槽钢 channel车底式加热炉car bottom furnace车轮轧机railway-wheel mill车丝机 threading machine成卷 coiling成品包装跨packing bay初轧机blooming mill初轧坯翻转装置bloom turnover device出料拉杆kick-out arm穿孔机 piercing mill粗轧机rough mill淬火炉 hardening furnace搭接炉焊管机lap-welded 打包用带钢轧机package 打捆机bundle machine打捆机 bundlerpipe millmill打印台 stamping station大型型钢轧机heavy section mill 导辊装置roller guide地上卷取机up coiler地下卷取机 down coiler地下卷取机 down coiler地下油库oil cellar地下运输机tunnel conveyer叠板轧机pack mill定径机 sizing mill定心机 centering machine镀槽coating bath镀锡板镀锡槽镀锡线镀锌板镀锌槽镀锌线堆储跨堆垛机tinning sheet tinning bath tinning line galvanized sheet galvanizing bath galvanizing line storage baypiler钝化处理passivation多辊矫直机multi-roll straightening machine 方钢 square方坯 bloombar非连续性轧机non-continuous rolling mill 飞锯 flying saw干燥台 drying station 钢坯,小方坯billet钢坯库billet store钢坯修磨 conditioning高速线材轧机high speed wire rod mill高压水除鳞hydraulic jet descaler工字钢I-bar工字钢轧机I-beam mill工作辊换辊装置 work roll changer工作辊支撑装置 work roller supporting apparatus 钩式运输机hook transfer光亮退火炉bright annealing furnace轨梁轧机rail-beam section mill滚筒剪drum type shear横切机 transversal shear厚板heavy plate厚板轧机heavy plate mill环形加热炉rotary hearth furnace换辊小车roll change carriage荒管,毛管,空心坯pierced billet,hollow billet回火炉tempering furnace回转剪rotary cropping shear活套loop活套张紧辊bridle roll机后输出辊道mill run-out table机架, 牌坊 stand, housing机架辊breast roll机前输入辊道mill run-in table挤压机extruder夹送辊 deflector pinch roll加热炉heating furnace碱槽 alkaline bath剪切跨 shear bay减径机reducing mill矫直机straightening machine, straightening mill角钢 angle steel揭盖机 cover carriage紧卷 tight coil进料拉杆kick-in arm浸镀immersion coating井式炉pit batch type furnace精轧机 finish mill精整加工线finishing machine精整跨 finishing bay卷材, 线卷 coil均热炉 pit furnace均热炉跨soaking pit bay均整机,整径机(管) reeling machine 开卷机, 拆卷机 decoiler开坯机 cogging mill可逆辊道reversing table空心坯减径机shell-reducing mill 拉丝机wire-drawing machine扩径机(管) repiercing machine冷床 cold bed冷锯 cold saw冷轧板带钢 cold rolled strip立辊 vertical roll连续式加热炉continuous type furnace 连续酸洗continuous acid-washing链式运输机 chain transfer磷化处理phosphate treatment 磷酸phosphoric acid硫酸sulfurous acid炉卷机steckel mill炉用卷取机furnace coiler轮箍轧机内表修磨拧接头机盘条rod tyre millinside grinding coupling applicator coil平立(万能)轧机horizontal-vertical(HV)mill 平整机 temper machine破鳞辊 descaling roll破鳞机scale breaker, descaler切边 side crops切边剪 end trimming shear切头 top crops切头剪end shear切尾 end crops去刺机 deburring machine热处理heat treatment热带轧机hot-strip mill热镀 hot-dip coating热锯hot saw热轧板带钢hot rolled strip乳化液emulsion森吉米尔轧机Sendzimir mill上料台架ingoing skid深冲薄钢板 deep drawing sheet石油管套管pipe case 收集台collecting table受料辊道输出辊道输入辊道水力除鳞receiving table run-out tablerun-in table hydraulic descaler水压试验机hydraulic pressure tester 酸槽acid bath酸洗槽pickling bath酸洗工段 pickling department酸洗机pickling 酸洗线pickling machine line酸洗用酸acid for pickling甩尾 back-end whip丝扣保护套thread protector四机架连续式带钢冷轧机four-stand tendem cold strip mill 松卷loose coil碎断剪 chopping shear塔式酸洗机 tower pickler套管接头pipe coupling铁皮坑 scale pit通径机 drifter筒式卷取机 drum type coiler涂漆装置painting unit吐丝机laying head推钢机, 推杆 pusher拖运机,移送机dragging device 脱脂槽 degreasing bath外表修磨outside grinding弯辊装置bending-up roll device万向连轴节universal spindle coupling无扭轧机non-twist mill无损探伤non destoryed test铣头机 chamfering machine限动芯棒轧管机retained mandrel pipe mill 硝酸nitric acid 小型型钢轧机light section mill, merchant bar mill芯棒式轧管机mandrel mill型钢, 条钢 bar行星轧机planetary rolling mill修磨机grinder压下螺丝 screw down压下装置, 压下机构 screwdown延伸机 elongator硬度试验机hardness tester油膜轴承oil film lubrication bearing预精轧机pre-finishing mill预热炉preheating furnace圆锭round ingot, round billet圆钢round bar圆盘锯 circular saw运锭车, 翻锭车 ingot buggy运输辊道processing table再加热炉reheating furnace轧边机, 立辊轧机 edger轧钢rolling轧钢车间rolling plant轧管机设备 tube mill equipment轧辊及辊道roller and table轧辊压下装置roller press-down device 轧辊轴承座roll bearing chock轧辊支架roll support轧机rolling mill轧机传动装置rolling mill drive device轧机跨mill bay, mill aisle轧机输出辊道mill delivery table轧机输入辊道mill approach table窄带strip张力减径机(管) tension-reducing machine 张力控制tension control罩式炉bell type furnace支撑辊back-up roll中板轧机medium plate mill中厚板medium plate中间辊道intermediate table中型宽带轧机medium wide-strip mill中型型钢轧机medium section mill中轧机intermediate mill周期式轧管机pilger mill转盘turntable自动轧管机plug mill纵切机longitudinal shear, slitting shear。

轧钢英语词汇汇总

ITC
Interstand tension control
紧急停止控制
ITG
Interface to technological
技术测量界面
LCS
Laminar cooling system
层流冷却系统
LCO
Line coordinator
权限协调
MAI
Manual intervention
人工干涉
设置数据处理
SDS
Screw down system
压下系统
SCO
Stand concentrator
机座集中器
SIC
Simulation computing
模拟处理
SGC
Side guide control
侧导板控制
THC
Thickness control
厚度控制
SGR
入口侧导板
SGX
出口侧导板
WCT
Width control
宽度控制
XTC
Exit temperature control
出口温度控制
DSS
Double side trimming shear
双边剪
EHS
Exhaust system
排气系统
EST
Emergency stop
紧急停止
NFC\XFC
入、出口卷取炉
FU
Furnace
加热炉
紧急事件系统
ETC
Edger tension control
立辊压力控制
FLC
Flatness control
平直度控制
PQE
Product quality erolution

轧钢专业英语必备词汇

(5)轧钢Rolling八辊轧机MKW mill板坯slab半连续热带轧机semi-continuous hot-strip mill 薄板sheet薄板轧机sheet mill保温炉heat holding furnace扁锭slab ingot, slab扁钢flat bar不可逆轧机non-reversing mill步进梁式加热炉walking beam type furnace 槽钢channel车底式加热炉car bottom furnace车轮轧机railway-wheel mill车丝机threading machine成卷coiling成品包装跨packing bay初轧机blooming mill初轧坯翻转装置bloom turnover device出料拉杆kick-out arm穿孔机piercing mill粗轧机rough mill淬火炉hardening furnace搭接炉焊管机lap-welded pipe mill打包用带钢轧机package mill打捆机bundle machine打捆机bundler打印台stamping station大型型钢轧机heavy section mill导辊装置roller guide地上卷取机up coiler地下卷取机down coiler地下卷取机down coiler地下油库oil cellar地下运输机tunnel conveyer叠板轧机pack mill定径机sizing mill定心机centering machine镀槽coating bath镀锡板tinning sheet镀锡槽tinning bath镀锡线tinning line镀锌板galvanized sheet镀锌槽galvanizing bath镀锌线galvanizing line堆储跨storage bay堆垛机piler钝化处理passivation多辊矫直机multi-roll straightening machine 方钢square bar方坯bloom非连续性轧机non-continuous rolling mill飞锯flying saw干燥台drying station钢坯, 小方坯billet钢坯库billet store钢坯修磨conditioning高速线材轧机high speed wire rod mill高压水除鳞hydraulic jet descaler工字钢I-bar工字钢轧机I-beam mill工作辊换辊装置work roll changer工作辊支撑装置work roller supporting apparatus 钩式运输机hook transfer光亮退火炉bright annealing furnace轨梁轧机rail-beam section mill滚筒剪drum type shear横切机transversal shear厚板heavy plate厚板轧机heavy plate mill环形加热炉rotary hearth furnace换辊小车roll change carriage荒管, 毛管, 空心坯pierced billet, hollow billet回火炉tempering furnace回转剪rotary cropping shear活套loop活套张紧辊bridle roll机后输出辊道mill run-out table机架, 牌坊stand, housing机架辊breast roll机前输入辊道mill run-in table挤压机extruder夹送辊deflector pinch roll加热炉heating furnace碱槽alkaline bath剪切跨shear bay减径机reducing mill矫直机straightening machine, straightening mill角钢angle steel揭盖机cover carriage紧卷tight coil进料拉杆kick-in arm浸镀immersion coating井式炉pit batch type furnace精轧机finish mill精整加工线finishing machine精整跨finishing bay卷材, 线卷coil均热炉pit furnace均热炉跨soaking pit bay均整机,整径机(管) reeling machine开卷机, 拆卷机decoiler开坯机cogging mill可逆辊道reversing table空心坯减径机shell-reducing mill拉丝机wire-drawing machine扩径机(管) repiercing machine冷床cold bed冷锯cold saw冷轧板带钢cold rolled strip立辊vertical roll连续式加热炉continuous type furnace 连续酸洗continuous acid-washing链式运输机chain transfer磷化处理phosphate treatment磷酸phosphoric acid硫酸sulfurous acid炉卷机steckel mill炉用卷取机furnace coiler轮箍轧机tyre mill内表修磨inside grinding拧接头机coupling applicator盘条rod coil平立(万能)轧机horizontal-vertical (HV) mill 平整机temper machine破鳞辊descaling roll破鳞机scale breaker, descaler切边side crops切边剪end trimming shear切头top crops切头剪end shear切尾end crops去刺机deburring machine热处理heat treatment热带轧机hot-strip mill热镀hot-dip coating热锯hot saw热轧板带钢hot rolled strip乳化液emulsion森吉米尔轧机Sendzimir mill上料台架ingoing skid深冲薄钢板deep drawing sheet石油管套管pipe case收集台collecting table受料辊道receiving table输出辊道run-out table输入辊道run-in table水力除鳞hydraulic descaler水压试验机hydraulic pressure tester酸槽acid bath酸洗槽pickling bath酸洗工段pickling department酸洗机pickling machine酸洗线pickling line酸洗用酸acid for pickling甩尾back-end whip丝扣保护套thread protector四机架连续式带钢冷轧机four-stand tendem cold strip mill 松卷loose coil碎断剪chopping shear塔式酸洗机tower pickler套管接头pipe coupling铁皮坑scale pit通径机drifter筒式卷取机drum type coiler涂漆装置painting unit吐丝机laying head推钢机, 推杆pusher拖运机,移送机dragging device脱脂槽degreasing bath外表修磨outside grinding弯辊装置bending-up roll device万向连轴节universal spindle coupling无扭轧机non-twist mill无损探伤non destoryed test铣头机chamfering machine限动芯棒轧管机retained mandrel pipe mill硝酸nitric acid小型型钢轧机light section mill, merchant bar mill 芯棒式轧管机mandrel mill型钢, 条钢bar行星轧机planetary rolling mill修磨机grinder压下螺丝screw down压下装置, 压下机构screwdown延伸机elongator硬度试验机hardness tester油膜轴承oil film lubrication bearing预精轧机pre-finishing mill预热炉preheating furnace圆锭round ingot, round billet圆钢round bar圆盘锯circular saw运锭车, 翻锭车ingot buggy运输辊道processing table再加热炉reheating furnace轧边机, 立辊轧机edger轧钢rolling轧钢车间rolling plant轧管机设备tube mill equipment轧辊及辊道roller and table轧辊压下装置roller press-down device轧辊轴承座roll bearing chock轧辊支架roll support轧机rolling mill轧机传动装置rolling mill drive device轧机跨mill bay, mill aisle轧机输出辊道mill delivery table轧机输入辊道mill approach table窄带strip张力减径机(管) tension-reducing machine 张力控制tension control罩式炉bell type furnace支撑辊back-up roll中板轧机medium plate mill中厚板medium plate中间辊道intermediate table中型宽带轧机medium wide-strip mill中型型钢轧机medium section mill中轧机intermediate mill周期式轧管机pilger mill转盘turntable自动轧管机plug mill纵切机longitudinal shear, slitting shear。

轧钢专业英语词汇1

blade creep adjustment scrap buckets crane pneumatic structure saddle material accumulator
刀刃、剪刃慢速、蠕动调整(节) 切头料斗天车、吊车,起重机气动结构鞍座(托座) 材料活套
ancillary efficient shapemeter roll dust gauze shutter stand by step control pneumatic system scrap shear
剪切强度惰辊夹送辊修边机导向辊压紧辊套筒测张力辊擦拭辊
resolution consumption cradle roller conveyor beam inspection roller table stationary deposit transfer(transp 悬臂吊 ort) 活套 pipework 整体机架 scrap 外伸轴承 circumference 焊接 chain 除鳞机 strap(ing) 平板车 eye strapping 连杆 coil marker 大(主)梁 railing 同步 covering 维护(修) anchoring 边界(缘)、(边)口downcoiler the unloading 拆卸、剥离 stations 布置、排列 :. 耐磨轴承 furthermore the coil handling 软管 system 效率 rotary 通信、联系 appendix electronic 喷焊粉 version 堆焊材料 spare part 分交合同 bought out 监制人 quotation 参加 remarks 计算 target date 说明书 breast rolls 目录 components 单、表 description 质量 documentation 检查等级 revision 修改 delivery

轧钢专业英语集锦

轧钢英语耐磨性 abrasive气孔 abscess横坐标 abscissa容纳、收纳 accommodating空气喷射 air ejection气动电机 air motor自动踏步控制 AJC=automatic jumping control 定中心、对中 align排成直线、列队、对中alignment交替、轮流alternate电流量amperage锚固、地脚anchor退火的annealed一年一次的annual能应用的、适用的、适合的applicable应用application增多，重视appreciate接近、进给approach适合的、特有的appropriate裙板apron相变arrest装配、组装、配件assembly分配assignment奥氏体austenite奥氏体轧制austenite rolling奥氏体的austenitic辅助液压auxiliary hydraulic轴向的axial后退、退回backlash平衡力balance force球面丝杆ball jack screw包装带分配器banding dispenser打捆带banding strap冷却段bank轴承架bearing bracker轴承箱bearing cage轴承座bearing chock轴承滑块，托瓦bearing shoes口径、钻孔bore支架、托架bracket脆性brittle青铜bronze水桶，废品箱bucket四轮小车buggy衬板bushing碰撞仪butt gauge计算calculation凸轮cam曲线度cambering amount辊型误差cambering profile悬梁cantilever有能力的capable能力capacity渗碳carburized小车，砂轮架carriage延伸辊道carry over table连铸坯分段剪CC shear中心线centerline离心机centrifuge房间chamber轴承座chock垫板choke linerC形沟C-hook溜槽chute圆周运动circular motion过滤设备clean-up device间隙clearance废钢收集装置cobble catcher带卷打捆机coil banding machine带卷运输机coil conveyor带卷检查线coil inspection line带卷提升机coil lifter托卷臂coil loading arm带卷打号机coil marking machine开卷机coil opener带卷鞍座coil saddle带卷鞍座coil skid带卷站coil station卸卷小车coil stripper car带卷回转台coil turner带卷称重装置coil weighter带卷跨coil yard卷取机进口侧导板coiler entry side guide 卷取温度coiling temperature收缩状态collapsed校准仪，准直仪collimator燃烧combustion补偿compensated复杂的complicate压缩空气compressed air计算机数据传输线computer data line凹面concave构想，认为conceive概念concept水泥，钢筋混凝土concrete条件condition联接conjunction控制台console统一，一致consortium控制器controller凸面convex凸形convex profile输送，运输convey冷却水cooling water冷却水管cooling water header相互作用correlation腐蚀性的corrosive支架cradle托辊cradle roll标准，准则criterion临界点critical point十字接头式万向接头cross pin type universal joint结晶crystallization立方体的cubic曲线curve剪切力cutting force剪切速度cutting speed周期的cyclic圆柱度cylindricity缓冲，减振dampen十年decade缺陷defect偏转辊deflector roll变形deformation变形抗力deformation resistance不管，危害despite超声波式涡流探伤仪detector of ultrasonic or eddy current type 消耗，磨损deteriorate不利的，有害的detrimental数字位置传感器digital positioning sensor先导伺服阀diredt servo valve散乱，分散dispersion忽视disregard明显的，不同的distinct分配器distributor龙门式double column type地下卷取机down coiler翻转装置down ender下游的downstream转鼓drum转鼓更换钩drum changing hook柔性，柔软的ductile延展性，延伸率ductility变钝，钝的dull动态的dynamic动平衡dynamic balance偏心套eccentricity ring偏心轴eccentricity shaft弹性材料elastic material电液伺服控制electro-hydraulic servo control 高度elevation除去，消除eliminated经验的empiric能量energy必要的，必不可少的essential优于，擅长excel专有的exclusive偏差excursion实现execute伸展expand分离（拆卸）装置extractor面板，花盘faceplate特点，特征feature毛毡felt铁素体ferrite铁素体轧钢ferrite rolling铁素体结构ferritic填充辊道fill-in table精轧机出口温度finisher delivery temperature 精轧机进口温度finisher entry temperature裂纹fissure固定导板fixed guide法兰flange楔形flared shape平面液晶显示器flat-face CRT裂纹flaw易弯曲的flexible挠性推爪flexible dog荧光的fluorescent尾座foot stock地脚螺栓foundation bolt框架frame全扩展状态fully expanded漏斗形funnel级别，钢种grade晶粒grain干油grease磨床grinder磨，打磨ground挡板guard导卫guide导辊guide roller导板guide-liner导向导板guiding apron旋转gyrating手轮hand wheel钩子hanger床头head stock高位水箱系统head tank system集水管header喷水横梁header piping保温罩heat holding cover高速飞剪high speed strip shear高速穿带装置high speed strip threading device 绞接hinge高速转动体hi-rotor起重机hoist压紧辊hold down roll1780热轧生产常用专用英语词汇Heating area:加热区Furnace 加热炉Gas 煤气Mixed gas 混合煤气Nitrogen 氮气Oxygen 氧气Resident oxygen 炉内残氧Pressure 压力Volume 体积、流量Valve 阀门Slab 板坯Slab yard 板坯库Continuous cast slab 连铸板坯Width 宽度Thickness 厚度Length 长度Weight 重量Bend 弯曲Combust 燃烧Temperature 温度Centigrade degree 摄氏度Pyrometer 高温计Thermocouples 热电偶Fixed beam 固定梁Walking beam 步进梁Forward 向前Backward 向后Discard 剔除Discard table 剔除辊道Charge 装炉Discharge 出炉Preheating zone 预热区Heating zone 加热区Soaking zone 均热区Vaporizing cooling/ vapor cooling 气化冷却Soft water 软水Scale 氧化铁皮Ventilate 通风Chimney 烟囱Exhaust 废气Stack 烟道Roller table 辊道Baffle 挡板Charge machine 装钢机Discharge machine 出钢机Compressed air 压缩空气Burner 烧嘴Combustion air fan 助燃风机Recuperative heat exchanger回热式热交换器Refractory brick 耐火砖Mathematic model 数学模型Feed-forward 前馈Feedback 后馈/反馈Furnace pressure 炉压Temperature profile 温度曲线Hot rolling shop：热轧车间Mill 轧机4-high finishing mill 四辊精轧机Rough mill 粗轧Screw down 压下Screw up 抬升辊缝Edger 立辊轧机，轧边机High-pressure descaling system 高压水除鳞系统Nozzle 喷嘴Heat cover 保温罩Shear 剪机Hydraulic loop 液压活套Looper 活套辊Side guide 侧导卫Interstand cooling 机架间冷却Run-out table 精轧输出辊道Laminar cooling 层流冷却Head water tank 高位水箱Side stripper 侧喷头Pinch roll 夹送辊Down Coiler 卷取机Mandrel 卷取机芯轴Wrapper roller 助卷辊Coil stripper car 卸卷小车Strip catcher 卷取区域带钢拦截装置Gear motor 齿轮马达Coupling 接手，连接器Spindle 接轴Universal Spindle 万向接轴Shaft 轴Roll changing device 换辊装置Crane 行车Bite 咬入Cascade speed adjustment 节联调速Cobble 堆钢事故，中间事故坯料Tension 张力Tension control 张力控制Loop height 活套量/活套高度Speed up 升速Lock cylinder 锁紧缸Balance cylinder 平衡缸Lift 提升Shift 横移Leveling 校平，调平Zero 校零Alignment 对中Industrial water 循环水Water volume 水量Water pressure 水压Cooling rate 冷却速度Speed cone 速度锥Maintenance 检修，维护Pneumatic system 气动系统Roll shop 轧辊间Roll 轧辊Grinder 磨床Work roll grinder 工作辊磨床Combinative/universal grinder 组合磨床Work roll 工作辊Back-up roll 支撑辊Barrel 辊身Roll neck 辊颈Roll cooling 轧辊冷却Work roll chock 工作辊轴承座Work roll bending system 工作辊弯辊系统Work roll shifting system 工作辊窜辊系统Back-up roll chock 支撑辊轴承座Bearing 轴承Work roll bearing 工作辊轴承Oil film bearing/morgoil bearing 油膜轴承Headstock 头架Tailstock 尾架Grinding carriage 磨头滑架Wheel 砂轮Dressing diamond 修整金刚石Measure 测量Size 尺寸Diameter 直径Ovality 不圆度Roundness 圆度Eccentricity 偏心度Contour 外形轮廓Geometry 几何尺寸，几何形状Curve 曲线Sine curve 正玄曲线Active curve 实际曲线Rated curve 额定曲线/设定的曲线Position 位置Axis 轴，数轴Horizontal 水平的V ertical 垂直的Calibration 校准，刻度Compensation 补偿Correction 纠正Control panel 控制面板，操作控制台Deviation 偏差Error 误差，错误Offset 偏差量Definition 定义Reverse 反转Swivel 回转，转动Distance 距离Range 范围Chamfer 凸度Centerline 中心线Infeed mode 进给模式Limit 限制，极限Limit switch 限位开关Scan 扫描Coolant 冷却剂Surface 表面Plunge grinding 掏沟磨削Caliper 测量卡规Optimize 优化Load roll 装辊Unload roll 卸辊Calibrate caliper 校准测量卡规Finishing area 精整区域Coil marking machine 钢卷标号机Coil strapping machine 钢卷打捆机Coil weighing device 钢卷称重装置Sampling shear 取样剪Transfer chain 链条运输机Walking beam transfer 步进梁运输机Coil yard 钢卷库Skin pass 平整机Saddle 鞍座Electric room 电气室Motor 电机Main motor 主电机Load 载荷Over load 过载Motor load 电机负荷Rolling force 轧制力Rolling speed 轧制速度MPM: meter per minute 米/分钟Torque 扭矩Rated torque 额定扭矩V oltage 电压Process computer 过程计算机Program 程序，编程PLC：programmable logic controller 可编程控制器Encoder 编码器Information 信息Ghost rolling 模拟轧制Measuring instrument 测量仪表X-ray X射线Thickness gauge 测厚仪Width gauge 测宽仪HMD: hot material detector 热金属探测仪CMD: cold material detector 冷金属探测仪Light barrier 光栅Automatic model 自动模式Semi-auto model 半自动模式Manual model 手动模式Emergency 紧急，急停Joggle 点动HMI：human machine interface 人机界面AC frequency converter 交流变频器I/O：input/output 输入/输出端口Step control 卷取机助卷辊的“踏步”控Hydraulic system 液压系统Grease 甘油Oil 油，稀油Oil station 油站SSC: Short stroke control 短行程控制AGC: automatic gauge control 自动压下控制A WC: automatic width control 自动宽度控制Pump 泵Screw pump 螺杆泵Filter 过滤器，滤网Cylinder 液压缸，圆柱体V alve stand 阀台Accumulator 蓄能器Leakage 泄漏Product 产品Grade 钢种Batch 一炉，一批Batch No. 炉批号Coil 钢卷Strip 带钢，薄带钢Sheet 钢板，薄钢板Plate 中厚板Physical performance 物理性能Mechanical performance 机械性能Strength 强度Elongation 延伸Flatness 平直度Plasticity 塑性Crown/chamber 凸度Hardness 硬度Microstructure 微观组织结构Austenite 奥氏体Ferrite 铁素体Pearlite 珠光体Deep drawn 深冲SPHC 普通级热轧钢板（卷）SPHD 深冲级热轧钢板（卷）SPCC 普通级冷轧钢板（卷）SPCD 深冲级冷轧钢板（卷High strength low-alloy steel 低合金高强度钢Silicon steel 硅钢，电工钢Galvanizing 镀锌Coating 涂镀，涂层Heat treatment 热处理Aging 时效处理Annealing 退火Quenching 淬火Alarm 报警Anchoring bolt 地脚螺栓Yield 产量，成材率Ton 吨Annual 一年的Month 月Day 日Shift 班Safety 安全Radioactive hazard 放射性伤害Caution 注意，小心Layout 平面布置Document 文件Documentation 技术文本，技术文件报价书TOP: take-over point 交接点冶金产品中英对照汉英[原创]钢铁产品碳素结构钢 Carbon Construction Steel碳素工具钢 Carbon Tool Steel合金结构钢 Alloy Construction Steel合金工具钢 Alloy Tool Steel高速工具钢 High Speed Tool Steel弹簧钢 Spring Steel不锈耐热钢 Stainless & Heat Resisting Steel轴承钢 Bearing Steel工字钢 Ibeam普通圆钢 Round Steel槽钢 Channel扁钢 Flat Steel Bar等边角钢 Equal Angle Steel不等边角钢 Unequal Angle Steelh型钢 Hbeam钢坯 Billet,Bloom钢筋混凝土用变形钢筋 High Strength Deformed Steel Bar窗框钢 Window Sash中厚钢板 Steel Plate热轧钢板（卷） Hot Rolled Steel Coil冷轧钢板（卷） Cold Rolled Steel Sheel or Coil镀锌钢板（卷） Galvanized Steel Coil钢带 Steel Strip线材 Wire Rod Coil无缝钢管 Seamless Steel Pipe锅炉管 Boiler Tube石油套管 Pipe For Oil Field高压管 Pressure Pipe高压气瓶用管 Tube for High-Pressure Vessel地质钻探用管 Seamless Steel Pipe For Geological Drill In 镀锌焊管 Galvanized Welded Pipe石油钻探杆 Drill Pipe For Oil Field铸铁管 Cast Iron Pipe重轨 Heavy Rail轻轨 Light Rail炼钢生铁 Basic Pig Iron铸造生铁 foundry Pig Iron普通圆钢钉 Round Nails for General Uses镀锌底碳钢丝 Galvanized Low Carbon Steel Wire.钢丝绳 Steel Wire Rope钢绞线 Stranded Wire预应力混凝土钢丝 Steel Wire For Prestressed Concrete 窗纱 Window Screen车轮 Wheel Tyre轮筛 Wheel Circle。

轧钢钢材行业专业英语

轧钢专业英语Carburizing Steel 碳钢['ka:bjuraiziŋ]Cast-Steel 铸钢Cast-Steel Pipe 铸钢管Cold-Pressed Sheet Steel 冷压薄钢板Cold-Strip Steel Rolling Mill 冷轧带钢机; 带钢冷轧机Strip n. 带；条状；Cold strip 冷轧带材Rolling mill 轧钢厂；辊(gun)轧机Common Straight Carbon Steel 普通碳素钢合金工具钢Alloy Tool Steel合金结构钢Alloy Construction Steel碳素工具钢Carbon Tool Steel高速工具钢High Speed Tool Steel弹簧钢Spring Steel spring 弹簧工字钢Ibeam普通圆钢Round Steel槽钢Channel扁钢Flat Steel Bar等边角钢Equal Angle Steel不等边角钢Unequal Angle Steel型钢Hbeam 型钢就是H型钢，和工字钢一起属于型材。

钢坯Billet,Bloom钢带Steel Strip线材Wire Rod Coilwire rod [材] 线材；[材] 盘条；盘圆；钢丝筋条Coil n. 线圈；卷车轮Wheel Tyre轮筛Wheel CircleRolling-mill housing 轧机机架Rolling mill 轧钢厂；辊轧机Housing [机] 外壳；遮盖物；机器等的防护外壳或外罩bed 底座roller 辊(gun)n. [机] 滚筒；[机] 滚轴；辊子；滚转机moulded steel 铸钢alloy steel 合金钢bloom 初轧方坯coiled sheet 带状薄板薄板卷heating 加热preheating 预热tempering 回火碳钢回火temper 回火hardening 淬水n. 硬化；淬火；锻炼annealing 退火[ə'nilɪŋ] n. 热处理；低温退火；磨炼v. [机][生化] 退火；磨炼（anneal的ing形式）reduction 还原n. 减少；下降；缩小cooling 冷却rolling 轧制drawing 拉拔extrusion 挤压wiredrawing 拉丝n. [机] 拉丝，拖长；制造铁丝stamping, pressing 冲压Stamping n. 冲击制品die casting 拉模铸造压铸，拉模铸造Casting n. 铸造；铸件；投掷；角色分配v. 铸造；投掷；投向；选派演员；扔掉forging 锻造v. 锻造；打制turning 车削n. 转向；旋转；回转；转弯处v. 旋转milling 铣削n. 磨；制粉；轧齿边v. 碾磨；磨成粉；滚（碾轧）金属Milling machine [机] 铣床machining, tooling 加工blowhole 气孔n. （鲸、海豚等的）喷水孔；（隧道等的）通风孔；岩石孔穴；[材] 气泡Black Mild Steel Hexagonal Nut 黑铁六角螺丝帽Hexagonal 英[hek'sæɡənəl] 美[hɛk'sægənl]adj. 六边的，六角形的Nut n. 螺母，螺帽；坚果；难对付的人，难解的问题vi. 采坚果Black Mild Steel Pan Head Rivet 黑铁锥头铆钉Rivet n. 铆钉vt. 铆接；固定；（把目光、注意力等）集中于Black Mild Steel Round Head Rivet 黑铁圆头铆钉Black Mild Steel Square Nut 黑铁四方螺丝帽accelerated cooling 加速冷却accelerated creep 加速蠕变accelerated diffusion 加速扩散accelerated leaching 加速浸出accelerated rolling 加速轧制stainless steel 不锈钢Austenitic Steel 奥氏体钢Austenitic Stainless Steel 奥氏体不锈钢Banding Steel 带钢; 箍钢Bar Steel 棒钢; 条钢Carbon Content Of Steel 钢含碳量austenitic alloy steel 奥氏体合金钢axle shaft steel 车轴钢Cold-Roll Steel Sheets 冷轧钢板无缝钢管Seamless Steel Pipeiron and steel industry 钢铁工业stamping, pressing 冲压blowhole 气孔Bearing Steel 轴承钢吐丝机和输送机laying head and conveyor converter 变频器，转炉approach table 输入辊道backstepping 逐步退焊法backup roll 支承辊backup roll bending 支承辊弯曲break down mill 开毗机breakdown bar 中间轧坯bumper 挡板bunch 捆bunching machine 线盘捆扎机butt welding 对接焊centrifugal force 离心力centrifugal pump 离心泵centrifugal separator 离心分离器chilled roll 冷硬铸铁轧辊cluster 群cluster mill 多辊轧机;六辊式轧机coefficient 系数coefficient of absorption 吸收系数coefficient of compressibility 压缩系数coefficient of cubic expansion 体膨胀系数coefficient of elasticity 弹性系数coefficient of elasticity in shear 剪切弹性模量cog 初轧坯cogged ingot 初轧坯cogging 初轧cold riveting 冷铆cold rolled band 冷轧带钢cold rolled shape 冷轧型钢cold rolled sheet 冷轧薄板cold rolled steel 冷轧钢cold rolled strip 冷轧带钢cold rolled tube 冷轧管cold repair 冷修continuous cold mill train 连续冷轧机组continuous cooling 连续冷却continuous drawing 连续拉伸continuous drawing machine 连续拉线机continuous finishing mill group 连续精轧机组continuous mill 连轧机continuous roughing mill group 连续粗轧机组continuous rolling 连续轧制crocodile shears 杠杆式剪断机crop 钢锭切头crop bucket 切头箱crop conveyor 切头运输机crop loss 切头损耗crop shears 剪头机cropping 切头cropping saw 切头锯cross roll straightener 斜辊矫直机cross roll straightening machine 斜辊矫直机cross rolling 横向轧制cross rolling mill 横轧机cross rolls 斜辊crank shears 曲柄式剪切机critical density 临界密度critical diameter 临界直径critical grain growth 临界晶粒长大critical load 临界荷重critical mass 临界质量critical nucleus size 临界核尺寸critical point 临界点critical quenching rate 临界淬火速度critical range 临界范围critical shear stress 临界切应力critical speed 临界速度critical state 临界状态critical stress 临界应力critical temperature 临界温度critical value 临界值critical velocity 临界速度。

轧钢专业英语必备词汇

轧钢专业英语必备词汇(5)轧钢Rolling八辊轧机MKW mill板坯slab半连续热带轧机semi-continuous hot-strip mill 薄板sheet 薄板轧机sheet mill保温炉heat holding furnace扁锭slab ingot, slab扁钢flat bar不可逆轧机non-reversing mill步进梁式加热炉walking beam type furnace 槽钢channel 车底式加热炉car bottom furnace车轮轧机railway-wheel mill车丝机threading machine成卷coiling成品包装跨packing bay初轧机blooming mill初轧坯翻转装置bloom turnover device出料拉杆kick-out arm穿孔机piercing mill粗轧机rough mill淬火炉hardening furnace搭接炉焊管机lap-welded pipe mill打包用带钢轧机package mill打捆机bundle machine打捆机bundler打印台stamping station大型型钢轧机heavy section mill导辊装置roller guide地上卷取机up coiler地下卷取机down coiler地下卷取机down coiler地下油库oil cellar地下运输机tunnel conveyer叠板轧机pack mill定径机sizing mill定心机centering machine镀槽coating bath镀锡板tinning sheet镀锡槽tinning bath镀锡线tinning line镀锌板galvanized sheet镀锌槽galvanizing bath镀锌线galvanizing line堆储跨storage bay堆垛机piler钝化处理passivation多辊矫直机multi-roll straightening machine 方钢square bar 方坯bloom非连续性轧机non-continuous rolling mill飞锯flying saw干燥台drying station钢坯, 小方坯billet钢坯库billet store钢坯修磨conditioning高速线材轧机high speed wire rod mill高压水除鳞hydraulic jet descaler工字钢I-bar工字钢轧机I-beam mill工作辊换辊装置work roll changer工作辊支撑装置work roller supporting apparatus 钩式运输机hook transfer光亮退火炉bright annealing furnace轨梁轧机rail-beam section mill滚筒剪drum type shear横切机transversal shear厚板heavy plate厚板轧机heavy plate mill环形加热炉rotary hearth furnace换辊小车roll change carriage荒管, 毛管, 空心坯pierced billet, hollow billet回火炉tempering furnace回转剪rotary cropping shear活套loop活套张紧辊bridle roll机后输出辊道mill run-out table机架, 牌坊stand, housing机架辊breast roll机前输入辊道mill run-in table挤压机extruder夹送辊deflector pinch roll加热炉heating furnace碱槽alkaline bath剪切跨shear bay减径机reducing mill矫直机straightening machine, straightening mill角钢angle steel揭盖机cover carriage紧卷tight coil进料拉杆kick-in arm浸镀immersion coating井式炉pit batch type furnace精轧机finish mill精整加工线finishing machine精整跨finishing bay卷材, 线卷coil均热炉pit furnace均热炉跨soaking pit bay均整机,整径机(管) reeling machine开卷机, 拆卷机decoiler开坯机cogging mill可逆辊道reversing table空心坯减径机shell-reducing mill拉丝机wire-drawing machine扩径机(管) repiercing machine冷床cold bed冷锯cold saw冷轧板带钢cold rolled strip立辊vertical roll连续式加热炉continuous type furnace 连续酸洗continuous acid-washing链式运输机chain transfer磷化处理phosphate treatment磷酸phosphoric acid硫酸sulfurous acid炉卷机steckel mill炉用卷取机furnace coiler轮箍轧机tyre mill内表修磨inside grinding拧接头机coupling applicator盘条rod coil平立(万能)轧机horizontal-vertical (HV) mill 平整机temper machine破鳞辊descaling roll破鳞机scale breaker, descaler切边side crops切边剪end trimming shear切头top crops切头剪end shear切尾end crops去刺机deburring machine热处理heat treatment热带轧机hot-strip mill热镀hot-dip coating热锯hot saw热轧板带钢hot rolled strip乳化液emulsion森吉米尔轧机Sendzimir mill上料台架ingoing skid深冲薄钢板deep drawing sheet石油管套管pipe case收集台collecting table受料辊道receiving table输出辊道run-out table输入辊道run-in table水力除鳞hydraulic descaler水压试验机hydraulic pressure tester酸槽acid bath酸洗槽pickling bath酸洗工段pickling department酸洗机pickling machine酸洗线pickling line酸洗用酸acid for pickling甩尾back-end whip丝扣保护套thread protector四机架连续式带钢冷轧机four-stand tendem cold strip mill 松卷loose coil碎断剪chopping shear塔式酸洗机tower pickler套管接头pipe coupling铁皮坑scale pit通径机drifter筒式卷取机drum type coiler涂漆装置painting unit吐丝机laying head推钢机, 推杆pusher拖运机,移送机dragging device脱脂槽degreasing bath外表修磨outside grinding弯辊装置bending-up roll device万向连轴节universal spindle coupling无扭轧机non-twist mill无损探伤non destoryed test铣头机chamfering machine限动芯棒轧管机retained mandrel pipe mill硝酸nitric acid小型型钢轧机light section mill, merchant bar mill 芯棒式轧管机mandrel mill型钢, 条钢bar行星轧机planetary rolling mill修磨机grinder压下螺丝screw down压下装置, 压下机构screwdown延伸机elongator硬度试验机hardness tester油膜轴承oil film lubrication bearing预精轧机pre-finishing mill预热炉preheating furnace圆锭round ingot, round billet圆钢round bar圆盘锯circular saw运锭车, 翻锭车ingot buggy运输辊道processing table再加热炉reheating furnace轧边机, 立辊轧机edger轧钢rolling轧钢车间rolling plant轧管机设备tube mill equipment轧辊及辊道roller and table轧辊压下装置roller press-down device轧辊轴承座roll bearing chock轧辊支架roll support轧机rolling mill轧机传动装置rolling mill drive device轧机跨mill bay, mill aisle轧机输出辊道mill delivery table轧机输入辊道mill approach table窄带strip张力减径机(管) tension-reducing machine 张力控制tensioncontrol罩式炉bell type furnace支撑辊back-up roll中板轧机medium plate mill中厚板medium plate中间辊道intermediate table中型宽带轧机medium wide-strip mill中型型钢轧机medium section mill中轧机intermediate mill周期式轧管机pilger mill转盘turntable自动轧管机plug mill纵切机longitudinal shear, slitting shear。

轧钢专业英语必备词汇

(5)轧钢Rolling八辊轧机MKW mill板坯slab半连续热带轧机semi-continuous hot-strip mill 薄板sheet薄板轧机sheet mill保温炉heat holding furnace扁锭slab ingot, slab扁钢flat bar不可逆轧机non-reversing mill步进梁式加热炉walking beam type furnace 槽钢channel车底式加热炉car bottom furnace车轮轧机railway-wheel mill车丝机threading machine成卷coiling成品包装跨packing bay初轧机blooming mill初轧坯翻转装置bloom turnover device出料拉杆kick-out arm穿孔机piercing mill粗轧机rough mill淬火炉hardening furnace搭接炉焊管机lap-welded pipe mill打包用带钢轧机package mill打捆机bundle machine打捆机bundler打印台stamping station大型型钢轧机heavy section mill导辊装置roller guide地上卷取机up coiler地下卷取机down coiler地下卷取机down coiler地下油库oil cellar地下运输机tunnel conveyer叠板轧机pack mill定径机sizing mill定心机centering machine镀槽coating bath镀锡板tinning sheet镀锡槽tinning bath镀锡线tinning line镀锌板galvanized sheet镀锌槽galvanizing bath镀锌线galvanizing line堆储跨storage bay堆垛机piler钝化处理passivation多辊矫直机multi-roll straightening machine 方钢square bar方坯bloom非连续性轧机non-continuous rolling mill飞锯flying saw干燥台drying station钢坯, 小方坯billet钢坯库billet store钢坯修磨conditioning高速线材轧机high speed wire rod mill高压水除鳞hydraulic jet descaler工字钢I-bar工字钢轧机I-beam mill工作辊换辊装置work roll changer工作辊支撑装置work roller supporting apparatus 钩式运输机hook transfer光亮退火炉bright annealing furnace轨梁轧机rail-beam section mill滚筒剪drum type shear横切机transversal shear厚板heavy plate厚板轧机heavy plate mill环形加热炉rotary hearth furnace换辊小车roll change carriage荒管, 毛管, 空心坯pierced billet, hollow billet回火炉tempering furnace回转剪rotary cropping shear活套loop活套张紧辊bridle roll机后输出辊道mill run-out table机架, 牌坊stand, housing机架辊breast roll机前输入辊道mill run-in table挤压机extruder夹送辊deflector pinch roll加热炉heating furnace碱槽alkaline bath剪切跨shear bay减径机reducing mill矫直机straightening machine, straightening mill角钢angle steel揭盖机cover carriage紧卷tight coil进料拉杆kick-in arm浸镀immersion coating井式炉pit batch type furnace精轧机finish mill精整加工线finishing machine精整跨finishing bay卷材, 线卷coil均热炉pit furnace均热炉跨soaking pit bay均整机,整径机(管) reeling machine开卷机, 拆卷机decoiler开坯机cogging mill可逆辊道reversing table空心坯减径机shell-reducing mill拉丝机wire-drawing machine扩径机(管) repiercing machine冷床cold bed冷锯cold saw冷轧板带钢cold rolled strip立辊vertical roll连续式加热炉continuous type furnace 连续酸洗continuous acid-washing链式运输机chain transfer磷化处理phosphate treatment磷酸phosphoric acid硫酸sulfurous acid炉卷机steckel mill炉用卷取机furnace coiler轮箍轧机tyre mill内表修磨inside grinding拧接头机coupling applicator盘条rod coil平立(万能)轧机horizontal-vertical (HV) mill 平整机temper machine破鳞辊descaling roll破鳞机scale breaker, descaler切边side crops切边剪end trimming shear切头top crops切头剪end shear切尾end crops去刺机deburring machine热处理heat treatment热带轧机hot-strip mill热镀hot-dip coating热锯hot saw热轧板带钢hot rolled strip乳化液emulsion森吉米尔轧机Sendzimir mill上料台架ingoing skid深冲薄钢板deep drawing sheet石油管套管pipe case收集台collecting table受料辊道receiving table输出辊道run-out table输入辊道run-in table水力除鳞hydraulic descaler水压试验机hydraulic pressure tester酸槽acid bath酸洗槽pickling bath酸洗工段pickling department酸洗机pickling machine酸洗线pickling line酸洗用酸acid for pickling甩尾back-end whip丝扣保护套thread protector四机架连续式带钢冷轧机four-stand tendem cold strip mill 松卷loose coil碎断剪chopping shear塔式酸洗机tower pickler套管接头pipe coupling铁皮坑scale pit通径机drifter筒式卷取机drum type coiler涂漆装置painting unit吐丝机laying head推钢机, 推杆pusher拖运机,移送机dragging device脱脂槽degreasing bath外表修磨outside grinding弯辊装置bending-up roll device万向连轴节universal spindle coupling无扭轧机non-twist mill无损探伤non destoryed test铣头机chamfering machine限动芯棒轧管机retained mandrel pipe mill硝酸nitric acid小型型钢轧机light section mill, merchant bar mill 芯棒式轧管机mandrel mill型钢, 条钢bar行星轧机planetary rolling mill修磨机grinder压下螺丝screw down压下装置, 压下机构screwdown延伸机elongator硬度试验机hardness tester油膜轴承oil film lubrication bearing预精轧机pre-finishing mill预热炉preheating furnace圆锭round ingot, round billet圆钢round bar圆盘锯circular saw运锭车, 翻锭车ingot buggy运输辊道processing table再加热炉reheating furnace轧边机, 立辊轧机edger轧钢rolling轧钢车间rolling plant轧管机设备tube mill equipment轧辊及辊道roller and table轧辊压下装置roller press-down device轧辊轴承座roll bearing chock轧辊支架roll support轧机rolling mill轧机传动装置rolling mill drive device轧机跨mill bay, mill aisle轧机输出辊道mill delivery table轧机输入辊道mill approach table窄带strip张力减径机(管) tension-reducing machine 张力控制tension control罩式炉bell type furnace支撑辊back-up roll中板轧机medium plate mill中厚板medium plate中间辊道intermediate table中型宽带轧机medium wide-strip mill中型型钢轧机medium section mill中轧机intermediate mill周期式轧管机pilger mill转盘turntable自动轧管机plug mill纵切机longitudinal shear, slitting shear。

轧钢专业英语词汇

pipework
管道布置
scrap
废品、碎片
circumference 圆周、周向
chain
拖链
strap(ing)
打包(捆扎)
eye strapping 径向打包
coil marker 带卷标印机
railing
栏杆、轨道
保护板(罩)、
covering
盖板
anchoring
锚固
downcoiler 地下卷取机
bending block center position control dege trimmer blade
creep adjustment scrap buckets crane pneumatic structure saddle material accumulator
弯辊块对中控制修边机刀刃、剪刃
内部表面喷射涂层间距恒定轴颈垫组装、装配
release corresponding
交付响应的
convery
运输
contact
接触
tensitometer looper
张力计活套
differential tension looper 差动活套
extension modules content railing
sinter powder weld up material the division list supervisior participate calculation specification catalogue sheet quality
Fasten Scrap Descaler Simultaneously Crack Rapidly Rebound tapered roller bearing latche obtain opposite diametrically contact pamel optimum Account blow-off pressure compensate wear liner calibration

轧钢专有名词英语集 (1)

軋鋼英語學習小集耐磨性 abrasive氣孔 abscess橫坐標 abscissa容納、收納 accommodating空氣噴射 air ejection氣動電機 air motor自動踏步控制 AJC=automatic jumping control 定中心、對中 align排成直線、列隊、對中 alignment交替、輪流 alternate電流量 amperage錨固、地腳 anchor退火的 annealed一年一次的 annual能應用的、適用的、適合的 applicable應用 application增多，重視 appreciate接近、進給 approach適合的、特有的 appropriate裙板 apron相變 arrest裝配、組裝、配件 assembly分配 assignment奧氏體 austenite奧氏體軋製 austenite rolling奧氏體的 austenitic輔助液壓 auxiliary hydraulic軸向的 axial後退、退回 backlash平衡力 balance force球面絲杆 ball jack screw包裝帶分配器 banding dispenser打捆帶 banding strap冷卻段 bank軸承架 bearing bracker軸承箱 bearing cage軸承座 bearing chock軸承滑塊，托瓦 bearing shoes口徑、鑽孔 bore支架、托架 bracket脆性 brittle青銅 bronze水桶，廢品箱 bucket四輪小車 buggy襯板 bushing碰撞儀 butt gauge計算 calculation凸輪 cam曲線度 cambering amount輥型誤差 cambering profile懸樑 cantilever有能力的 capable能力 capacity滲碳 carburized小車，砂輪架 carriage延伸輥道 carry over table連鑄坯分段剪 CC shear中心線 centerline離心機 centrifuge房間 chamber軸承座 chock墊板 choke linerC形溝 C-hook溜槽 chute圓周運動 circular motion過濾設備 clean-up device間隙 clearance廢鋼收集裝置 cobble catcher帶卷打捆機 coil banding machine 帶卷運輸機 coil conveyor帶卷檢查線 coil inspection line帶卷提升機 coil lifter托卷臂 coil loading arm帶卷打號機 coil marking machine開卷機 coil opener帶卷鞍座 coil saddle帶卷鞍座 coil skid帶卷站 coil station卸卷小車 coil stripper car帶卷回轉台 coil turner帶卷稱重裝置 coil weighter帶卷跨 coil yard卷取機進口側導板 coiler entry side guide卷取溫度 coiling temperature收縮狀態 collapsed校準儀，准直儀 collimator燃燒 combustion補償 compensated複雜的 complicate壓縮空氣 compressed air電腦資料傳輸線 computer data line凹面 concave構想，認為 conceive概念 concept水泥，鋼筋混凝土 concrete條件 condition聯接 conjunction控制台 console統一，一致 consortium控制器 controller凸面 convex凸形 convex profile輸送，運輸 convey冷卻水 cooling water冷卻水管 cooling water header相互作用 correlation腐蝕性的 corrosive支架 cradle托輥 cradle roll標準，準則 criterion臨界點 critical point十字接頭式萬向接頭 cross pin type universal joint結晶 crystallization立方體的 cubic曲線 curve剪切力 cutting force剪切速度 cutting speed圓柱度 cylindricity緩衝，減振 dampen十年 decade缺陷 defect偏轉輥 deflector roll變形 deformation變形抗力 deformation resistance不管，危害 despite超聲波式渦流探傷儀 detector of ultrasonic or eddy current type 消耗，磨損 deteriorate不利的，有害的 detrimental數字位置感測器 digital positioning sensor先導伺服閥 diredt servo valve散亂，分散 dispersion忽視 disregard明顯的，不同的 distinct分配器 distributor龍門式 double column type地下卷取機 down coiler翻轉裝置 down ender下游的 downstream轉鼓 drum轉鼓更換鉤 drum changing hook柔性，柔軟的 ductile延展性，延伸率 ductility變鈍，鈍的 dull動態的 dynamic動平衡 dynamic balance偏心套 eccentricity ring偏心軸 eccentricity shaft彈性材料 elastic material電液伺服控制 electro-hydraulic servo control高度 elevation除去，消除 eliminated經驗的 empiric能量 energy必要的，必不可少的 essential優於，擅長 excel專有的 exclusive偏差 excursion實現 execute伸展 expand分離（拆卸）裝置 extractor面板，花盤 faceplate特點，特徵 feature毛氈 felt鐵素體 ferrite鐵素體軋鋼 ferrite rolling鐵素體結構 ferritic填充輥道 fill-in table精軋機出口溫度 finisher delivery temperature 精軋機進口溫度 finisher entry temperature裂紋 fissure固定導板 fixed guide法蘭 flange楔形 flared shape平面液晶顯示器 flat-face CRT裂紋 flaw易彎曲的 flexible撓性推爪 flexible dog螢光的 fluorescent尾座 foot stock地腳螺栓 foundation bolt框架 frame全擴展狀態 fully expanded漏斗形 funnel級別，鋼種 grade晶粒 grain幹油 grease磨床 grinder磨，打磨 ground擋板 guard導衛 guide導輥 guide roller導板 guide-liner導向導板 guiding apron旋轉 gyrating手輪 hand wheel鉤子 hanger床頭 head stock高位水箱系統 head tank system集水管 header噴水橫樑 header piping保溫罩 heat holding cover高速飛剪 high speed strip shear高速穿帶裝置 high speed strip threading device 絞接 hinge高速轉動體 hi-rotor起重機 hoist壓緊輥 hold down roll熱軋生產常用專用英語詞彙冶金產品中英對照漢英[原創] Heating area:加熱區鋼鐵產品Furnace 加熱爐碳素結構鋼 Carbon Construct Gas 煤氣碳素工具鋼 Carbon Tool Stee Mixed gas 混合煤氣合金結構鋼 Alloy Construction Nitrogen 氮氣合金工具鋼 Alloy Tool Steel Oxygen 氧氣高速工具鋼 High Speed Tool Resident oxygen 爐內殘氧彈簧鋼 Spring Steel Pressure 壓力不鏽耐熱鋼 Stainless & Heat Volume 體積、流量軸承鋼 Bearing SteelValve 閥門工字鋼 IbeamSlab 板胚普通圓鋼 Round SteelSlab yard 板胚庫槽鋼 ChannelContinuous cast slab 連鑄板胚扁鋼 Flat Steel BarWidth 寬度等邊角鋼 Equal Angle Steel Thickness 厚度不等邊角鋼 Unequal Angle St Length 長度型鋼 HbeamWeight 重量鋼坯 Billet,Bloom鋼筋混凝土 High S Bend 彎曲窗框鋼 Window Sash Combust 燃燒中厚鋼板 Steel Plate Temperature 溫度熱軋鋼板（卷） Hot Rolled St Centigrade degree 攝氏度冷軋鋼板（卷） Cold Rolled S Pyrometer 高溫計鍍鋅鋼板（卷） Galvanized S Thermocouples 熱電偶鋼帶 Steel StripFixed beam 固定梁線材 Wire Rod CoilWalking beam 步進梁無縫鋼管 Seamless Steel Pip Forward 向前鍋爐管 Boiler Tube Backward 向後石油套管 Pipe For Oil Field Discard 剔除高壓管 Pressure Pipe Discard table 剔除輥道高壓氣瓶用管 Tube for High-P Charge 裝爐地質鑽探用管 Seamless Stee Discharge 出爐鍍鋅焊管 Galvanized Welded Preheating zone 預熱區石油鑽探杆 Drill Pipe For Oil F Heating zone 加熱區鑄鐵管 Cast Iron Pipe Soaking zone 均熱區Vaporizing cooling/ vapor cooling 氣化冷卻重軌 Heavy RailSoft water 軟水輕軌 Light RailScale 氧化鐵皮煉鋼生鐵 Basic Pig Iron Ventilate 通風鑄造生鐵 foundry Pig Iron Chimney 煙囪普通圓鋼釘 Round Nails for G Exhaust 廢氣鍍鋅底碳鋼絲 Galvanized LowStack 煙道鋼絲繩 Steel Wire Rope Roller table 輥道鋼絞線 Stranded WireBaffle 擋板預應力混凝土鋼絲 Steel Wire Charge machine 裝鋼機窗紗 Window Screen Discharge machine 出鋼機車輪 Wheel Tyre Compressed air 壓縮空氣輪篩 Wheel CircleBurner 燒嘴Combustion air fan 助燃風機Recuperative heat exchanger回熱式熱交換器Refractory brick 耐火磚Mathematic model 數學模型Feed-forward 前饋Feedback 後饋/回饋Furnace pressure 爐壓Temperature profile 溫度曲線Hot rolling shop：熱軋車間Mill 軋機4-high finishing mill 四輥精軋機Rough mill 粗軋Screw down 壓下Screw up 抬升輥縫Edger 立輥軋機，軋邊機High-pressure descaling system 高壓水除鱗系統Nozzle 噴嘴Heat cover 保溫罩Shear 剪機Hydraulic loop 液壓活套Looper 活套輥Side guide 側導衛Interstand cooling 機架間冷卻Run-out table 精軋輸出輥道Laminar cooling 層流冷卻Head water tank 高位水箱Side stripper 側噴頭Pinch roll 夾送輥Down Coiler 卷取機Mandrel 卷取機芯軸Wrapper roller 助卷輥Coil stripper car 卸卷小車Strip catcher 卷取區域帶鋼攔截裝置Gear motor 齒輪馬達Coupling 接手，連接器Spindle 接軸Universal Spindle 萬向接軸Shaft 軸Roll changing device 換輥裝置Crane 行車Bite 咬入Cascade speed adjustment 節聯調速Cobble 堆鋼事故，中間事故坯料Tension 張力Tension control 張力控制Loop height 活套量/活套高度Speed up 升速Lock cylinder 鎖緊缸Balance cylinder 平衡缸Lift 提升Shift 橫移Leveling 校平，調平Zero 校零Alignment 對中Industrial water 迴圈水Water volume 水量Water pressure 水壓Cooling rate 冷卻速度Speed cone 速度錐Maintenance 檢修，維護Pneumatic system 氣動系統Roll shop 軋輥間Roll 軋輥Grinder 磨床Work roll grinder 工作輥磨床Combinative/universal grinder 組合磨床Work roll 工作輥Barrel 輥身Roll neck 輥頸Roll cooling 軋輥冷卻Work roll chock 工作輥軸承座Work roll bending system 工作輥彎輥系統Work roll shifting system 工作輥竄輥系統Back-up roll chock 支撐輥軸承座Bearing 軸承Work roll bearing 工作輥軸承Oil film bearing/morgoil bearing 油膜軸承Headstock 頭架Tailstock 尾架Grinding carriage 磨頭滑架Wheel 砂輪Dressing diamond 修整金剛石Measure 測量Size 尺寸Diameter 直徑Ovality 不圓度Roundness 圓度Eccentricity 偏心度Contour 外形輪廓Geometry 幾何尺寸，幾何形狀Curve 曲線Sine curve 正玄曲線Active curve 實際曲線Rated curve 額定曲線/設定的曲線Position 位置Axis 軸，數軸Horizontal 水準的Vertical 垂直的Calibration 校準，刻度Compensation 補償Correction 糾正Control panel 控制台，操作控制台Deviation 偏差Error 誤差，錯誤Offset 偏差量Definition 定義Reverse 反轉Swivel 回轉，轉動Distance 距離Range 範圍Chamfer 凸度Centerline 中心線Infeed mode 進給模式Limit 限制，極限Limit switch 限位元開關Scan 掃描Coolant 冷卻劑Surface 表面Plunge grinding 掏溝磨削Caliper 測量卡規Optimize 優化Load roll 裝輥Unload roll 卸輥Calibrate caliper 校準測量卡規Finishing area 精整區域Coil marking machine 鋼標籤號機Coil strapping machine 鋼卷打捆機Coil weighing device 鋼卷稱重裝置Sampling shear 取樣剪Transfer chain 鏈條運輸機Walking beam transfer 步進梁運輸機Coil yard 鋼卷庫Skin pass 平整機Saddle 鞍座Electric room 電氣室Motor 電機Main motor 主電機Load 載荷Over load 超載Motor load 電機負荷Rolling force 軋製力Rolling speed 軋製速度MPM: meter per minute 米/分鐘Torque 扭矩Rated torque 額定扭矩Voltage 電壓Process computer 過程電腦Program 程式，程式設計PLC： programmable logic controller 可程式設計控制器Encoder 編碼器Information 信息Ghost rolling 模擬軋製Measuring instrument 測量儀錶X-ray X射線Thickness gauge 測厚儀Width gauge 測寬儀HMD: hot material detector 熱金屬探測儀CMD: cold material detector 冷金屬探測儀Light barrier 光柵Automatic model 自動模式Semi-auto model 半自動模式Manual model 手動模式Emergency 緊急，急停Joggle 點動HMI：human machine interface 人機界面AC frequency converter 交流變頻器I/O： input/output 輸入/輸出埠Step control 卷取機助卷輥的“踏步”控Hydraulic system 液壓系統Grease 甘油Oil 油，稀油Oil station 油站SSC: Short stroke control 短行程控制AGC: automatic gauge control 自動壓下控制AWC: automatic width control 自動寬度控制Pump 泵Screw pump 螺杆泵Filter 篩檢程式，濾網Cylinder 液壓缸，圓柱體Valve stand 閥台Accumulator 蓄能器Leakage 洩漏Product 產品Grade 鋼種Batch 一爐，一批Batch No. 爐批號Coil 鋼卷Strip 帶鋼，薄帶鋼Sheet 鋼板，薄鋼板Plate 中厚板Physical performance 物理性能Mechanical performance 機械性能Strength 強度Elongation 延伸Flatness 平直度Plasticity 塑性Crown/chamber 凸度Hardness 硬度Microstructure 微觀組織結構Austenite 奧氏體Ferrite 鐵素體Pearlite 珠光體Deep drawn 深沖SPHC 普通級熱軋鋼板（卷）SPHD 深沖級熱軋鋼板（卷）SPCC 普通級冷軋鋼板（卷）SPCD 深沖級冷軋鋼板（卷High strength low-alloy steel 低合金高強度鋼Silicon steel 矽鋼，電工鋼Galvanizing 鍍鋅Coating 塗鍍，塗層Heat treatment 熱處理Aging 時效處理Annealing 退火Quenching 淬火Alarm 報警Anchoring bolt 地腳螺栓Yield 產量，成材率Ton 噸Annual 一年的Month 月Day 日Shift 班Safety 安全Radioactive hazard 放射性傷害Caution 注意，小心Layout 平面佈置Document 文件Documentation 技術文本，技術檔報價書TOP: take-over point 交接點產品中英對照漢英[原創]產品結構鋼 Carbon Construction Steel工具鋼 Carbon Tool Steel結構鋼 Alloy Construction Steel工具鋼 Alloy Tool Steel工具鋼 High Speed Tool Steel鋼 Spring Steel耐熱鋼 Stainless & Heat Resisting Steel鋼 Bearing Steel鋼 Ibeam圓鋼 Round SteelChannelFlat Steel Bar角鋼 Equal Angle Steel邊角鋼 Unequal Angle SteelhHbeamBillet,Bloom混凝土用變形鋼筋 High Strength Deformed Steel Bar 鋼 Window Sash鋼板 Steel Plate鋼板（卷） Hot Rolled Steel Coil鋼板（卷） Cold Rolled Steel Sheel or Coil鋼板（卷） Galvanized Steel CoilSteel StripWire Rod Coil鋼管 Seamless Steel Pipe管 Boiler Tube套管 Pipe For Oil Field管 Pressure Pipe氣瓶用管 Tube for High-Pressure Vessel鑽探用管 Seamless Steel Pipe For Geological Drill In 焊管 Galvanized Welded Pipe鑽探杆 Drill Pipe For Oil Field管 Cast Iron PipeHeavy RailLight Rail生鐵 Basic Pig Iron生鐵 foundry Pig Iron圓鋼釘 Round Nails for General Uses底碳鋼絲 Galvanized Low Carbon Steel Wire.繩 Steel Wire Rope線 Stranded Wire力混凝土鋼絲 Steel Wire For Prestressed Concrete Window ScreenWheel TyreWheel Circlerod 棒;棒鋼rod mill 線材軋機;棒磨機roentgen 倫琴roentgen radiation 倫琴輻射roentgen rays x 射線roentgenogram x 射線照片roll 軋輥roll adjustment 軋輥蝶roll axis 軋輥軸線roll balance 軋輥的平衡roll barrel 輥身roll bending system 彎輥裝置roll body length 輥身長度roll caliber 軋輥孔型roll camber 輥身輪廓roll carriage 軋輥的軸承座roll change 換輥roll changing 換輥roll changing rig 換輥裝置roll chock 軋輥的軸承座roll cogging 在初軋機上軋製roll collar 輥環roll compacting 粉末軋製roll consumption 輥消耗roll coolant 軋輥冷卻乳液roll crown 軋輥凸度roll crusher 輥式破碎機roll deflection 軋輥撓度roll designing 軋輥孔型設計roll diameter 輥身直徑roll dressing 軋輥加工或磨削roll engaging sleeve 軋輥連接套筒roll fittings 軋輥導衛裝置roll flattening 軋輥壓扁roll force 軋製力roll formed shape 冷彎型鋼roll forming 輥軋成形roll forming mill 輥軋成形機roll gap 軋輥開度roll grinder 軋輥磨床roll grinding 軋輥研磨roll grinding machine 軋輥磨床roll mill stand stiffness 軋機剛性roll housing 軋機機架roll inventory 軋輥庫roll lathe 軋輥車床roll line 軋輥軸線roll mandrel 輥軸roll marks 輥印roll mill stand 軋機機座roll neck 輥頸roll opening 軋輥開度roll pass 軋輥孔型roll pass design 軋輥孔型設計roll pass sequence 軋輥孔型系統roll profile 軋輥輥型roll regrinding 軋輥再研磨roll scale 軋鋼皮roll screen 輥篩roll seperating force 軋製力roll setting 軋輥蝶roll setup 安置軋輥roll shape control 輥型第roll shift 軋輥軸向移動roll sleeve 軋輥輥套roll speed 軋製速度roll straightener 輥式矯正機roll stroke 軋輥升程roll table 輥道roll train 軋機機組roll turning 軋輥車削roll turning shop 軋輥車嫌工車間roll turning template 車曉輥用樣板roll type reel 輥式卷取機roll wear 軋輥磨損roll wobbler 軋輥梅花頭rollability 可軋製性rolled compact 軋坯rolled gold 覆飾用極薄金箔rolled in scale 軋入氧化皮rolled iron 軋製鋼材rolled pipe 軋製管rolled products 軋材rolled steel 軋製鋼材rolled stock 軋材rolled tube 軋製管rolled wire 軋製線材roller 輥子;軋鋼工roller bearing 滾柱軸承roller bearing steel 滾柱軸承鋼roller bed 輥道roller chain 滾子鏈roller cold pilgering mill 滾式冷軋管機roller conveyor 輥式運輸機roller cooling bed 輥式冷床roller die 輥模roller electrode 輥式電極roller feeder 輥式給料機roller guide 輥式導板roller hearth furnace 輥底式爐roller leveler 輥式矯直機roller line 輥道線roller reel 輥式卷取機roller spot welding 滾點焊roller straightening machine 輥式矯正機roller twister 輥式扭轉導板roller welding 軋焊roller's side 進料側rolling 軋製rolling axis 軋製線rolling cycle 軋製週期rolling direction 軋製方向rolling drawing process 軋製拉制法rolling equipment 軋製設備rolling friction 滾動摩擦rolling line 軋製線rolling mill 軋機rolling mill engine 軋機晝動機rolling mill practice 軋製工藝rolling plan 軋製圖解rolling plant 軋製車間rolling power 軋製能力rolling pressure 軋製壓力rolling program 軋製圖解rolling skin 軋製鐵鱗rolling solution 軋製用潤滑冷卻液rolling surface 滾動面rolling technology 軋製工藝rolling temperature 軋製溫度rolling temperature region 軋製溫度區rolling texture 軋製織構rolling torque 軋製力矩rolling width 軋製寬度roof 爐頂roofing sheet 屋面薄鋼板root 根部root crack 根部裂紋root gap 根部間隙root of penetration 焊縫根部root opening 根部間隙root pass 根部焊道root run 根部焊道rope 索rope manufacture 鋼絲繩製造rope transfer 鋼絲繩移送機rope wire 鋼絲繩用鋼絲roscoelite 釩雲母rosette graphite 玫瑰花狀石墨rotary converter 回轉式轉爐rotary crusher 回轉破碎機rotary cutter 圓盤式剪斷機rotary die 轉模rotary drier 回轉乾燥器rotary drum grinder 滾筒粉碎機rotary filter 滾筒過濾機rotary forge mill 週期式軋管機rotary furnace 回轉爐rotary hearth furnace 轉底爐rotary kiln 回轉爐rotary kiln reduction 回轉爐還原rotary piercing 斜輥式穿孔rotary piercing mill 斜輥式穿軋機rotary pump 回轉泵rotary shears 圓盤剪切機rotary squeezer 回轉壓榨機rotary swager 旋轉鍛造機rotary swaging 回轉模鍛rotary trimming shears 圓盤式切邊剪rotary tube straightener 旋轉式鋼管矯直機rotary vacuum pump 回轉真空泵rotating anode 旋轉陽極rotating arc 旋轉電弧rotating arc welding 旋轉電弧悍rotating bending test 旋轉彎曲試驗rotating cathode 旋轉陰極rotating crystal method 旋轉結晶法rotating cube mixer 旋轉箱式混料機rotating guide 旋轉導板rotating screen 回轉篩rotation axis 轉動軸rotational slip 轉動滑移roto arc welding 旋轉電弧悍rotoblasting 鐵砂清理rotor process 氧氣平吹旋轉轉爐煉鋼法rottenstone 矽藻土rouge 鐵丹rough forging 粗鍛造rough grinding 粗研磨rough surface 粗面rougher 開毗機roughing 粗軋roughing groove 粗軋孔型roughing mill group 粗軋機組roughing pass 粗軋孔型roughing slag 下渣roughing train 粗軋機線roughness 粗糙度roughness factor 粗糙度係數round billet 圓形坯round concrete bar 混凝土用圓鋼round ingot 圓錠round kiln 圓形爐round pass 圓形孔型round steel 圓鋼rounding 倒角rounds 圓鋼row of dislocations 位錯排列rubber mold 橡皮鑄型rubber packing 橡皮墊rubellite 紅電氣石rubidium 銣rubidium alum 銣茂rubidium chloride 氯化銣ruby copper 赤銅礦ruhrstahl heraeus process 雙管迴圈真空除氣法run 道run off tab 引出板run out table 輸出輥道runner 出鋼槽runner box 分叉澆口箱runner brick 湯道磚running out 跑號running repair 小修running time 運轉時間runoff table 輸出輥道runout 瘤;漏鐵水rupture 破壞rupture stress 斷裂應力rust 鏽rust inhibitor 防銹劑rust protection 抗鏽rust remover 除鏽劑rust resistance 耐銹蝕性rusting 生銹ruthenium 釕rutile 金紅石rutile electrode 氧化鈦藥皮焊條rz powder rz 粉末Heating area:加熱區Furnace 加熱爐Gas 煤氣Mixed gas 混合煤氣Nitrogen 氮氣Oxygen 氧氣Resident oxygen 爐內殘氧Pressure 壓力Volume 體積、流量Valve 閥門Slab 板坯Slab yard 板坯庫Continuous cast slab 連鑄板坯Width 寬度Thickness 厚度Length 長度Weight 重量Bend 彎曲Combust 燃燒Temperature 溫度Centigrade degree 攝氏度Pyrometer 高溫計Thermocouples 熱電偶Fixed beam 固定梁Walking beam 步進梁Forward 向前Backward 向後Discard 剔除Discard table 剔除輥道Charge 裝爐Discharge 出爐Preheating zone 預熱區Heating zone 加熱區Soaking zone 均熱區Vaporizing cooling/ vapour cooling 氣化冷卻Soft water 軟水Scale 氧化鐵皮Ventilate 透風Chimney 煙囪Exhaust 廢氣Stack 煙道Roller table 輥道Baffle 擋板Charge machine 裝鋼機Discharge machine 出鋼機Compressed air 壓縮空氣Burner 燒嘴Combustion air fan 助燃風機Recuperative heat exchanger回熱式熱交換器Refractory brick 耐火磚Mathematic model 數學模型Feed-forward 前饋Feedback 後饋/回饋Furnace pressure 爐壓Temperature profile 溫度曲線Hot rolling shop：熱軋車間 Mill 軋機4-high finishing mill 四輥精軋機Rough mill 粗軋Screw down 壓下Screw up 抬升輥縫Edger 立輥軋機，軋邊機High-pressure descaling system 高壓水除鱗系統Nozzle 噴嘴Heat cover 保溫罩Shear 剪機Hydraulic loop液壓活套Looper 活套輥Side guide 側導衛Interstand cooling 機架間冷卻Run-out table 精軋輸出輥道Laminar cooling 層流冷卻Head water tunk 高位水箱Side stripper 側噴頭Pinch roll 夾送輥Down Coiler 卷取機Mandrel 卷取機芯軸Wrapper roller 助卷輥Coil stripper car 卸卷小車Strip catcher 卷取區域帶鋼攔截裝置 Gear motor 齒輪馬達Coupling 接手，連接器Spindle 接軸Universal Spindle 萬向接軸Shaft 軸Roll changing device 換輥裝置Crane 行車Bite 咬進Cascade speed adjustment 節聯調速Cobble 堆鋼事故，中間事故坯料Tension 張力Tension control 張力控制Loop height 活套量/活套高度Speed up 升速 Lock cylinder 鎖緊缸Balance cylinder 平衡缸Lift 提升Shift 橫移Leveling 校平，調平Zero 校零Alignment 對中Industrial water 迴圈水Water volume 水量Water pressure 水壓Cooling rate 冷卻速度Speed cone 速度錐Maintenance 檢驗，維護Pneumatic system 氣動系統Roll shop 軋輥間Roll 軋輥Grinder 磨床Work roll grinder 工作輥磨床Combinative/universal grinder 組合磨床Work roll 工作輥Back-up roll 支撐輥Barrel 輥身Roll neck 輥頸Roll cooling 軋輥冷卻Work roll chock 工作輥軸承座Work roll bending system 工作輥彎輥系統Work roll shifting system 工作輥竄輥系統Back-up roll chock 支撐輥軸承座Bearing 軸承Work roll bearing 工作輥軸承Oil film bearing/morgoil bearing 油膜軸承Headstock 頭架Tailstock 尾架Grinding carriage 磨頭滑架Wheel 砂輪 Dressing diamond 修整金剛石Measure 丈量Size 尺寸Diameter 直徑Ovality 不圓度Roundness 圓度Eccentricity 偏心度Contour 外形輪廓Geometry 幾何尺寸，幾何外形Curve 曲線Sine curve 正玄曲線Active curve 實際曲線Rated curve 額定曲線/設定的曲線Position 位置Axis 軸，數軸Horizontal 水準的Vertical 垂直的Calibration 校準，刻度Compensation 補償Correction 糾正Control panel 控制台，操縱控制台Deviation 偏差Error 誤差，錯誤Offset 偏差量Definition 定義 Reverse 反轉Swivel 回轉，轉動Distance 間隔Range 範圍 Chamfer 凸度Centerline 中心線Infeed mode 進給模式Limit 限制，極限Limit switch 限位元開關Scan 掃描Coolant 冷卻劑Su***ce 表面Plunge grinding 掏溝磨削Caliper 丈量卡規Optimize 優化Load roll 裝輥Unload roll 卸輥Calibrate caliper 校準丈量卡規Finishing area 精整區域Coil marking machine 鋼標籤號機Coil strapping machine 鋼卷打捆機Coil weighing device 鋼卷稱重裝置Sampling shear 取樣剪Transfer chain 鏈條運輸機Walking beam transfer 步進梁運輸機Coil yard 鋼卷庫Skin pass 平整機Saddle 鞍座Electric room 電氣室Motor 電機Main motor 主電機Load 載荷Over load 超載Motor load 電機負荷Rolling force 軋製力Rolling speed 軋製速度MPM: meter per minute 米/分鐘Torque 扭矩Rated torque 額定扭矩Voltage 電壓Process computer 過程電腦Program 程式，程式設計PLC： programmable logic controller 可程式設計控制器Encoder 編碼器Information 信息Ghost rolling 模擬軋製Measuring instrument 丈量儀錶X-ray X射線Thickness gauge 測厚儀Width gauge 測寬儀HMD: hot material detector 熱金屬探測儀CMD: cold material detector 冷金屬探測儀Light barrier 光柵Automatic model 自動模式Semi-auto model 半自動模式Manual model 手動模式Emergency 緊急，急停Joggle 點動HMI：human machine inte***ce 人機界面AC frequency converter 交流變頻器I/O： input/output 輸進/輸出埠Step control 卷取機助卷輥的“踏步”控制Hydraulic system 液壓系統Grease 甘油Oil 油，稀油Oil station 油站SSC: Short stroke control 短行程控制AGC: automatic gauge control 自動壓下控制AWC: automatic width control 自動寬度控制Pump 泵Screw pump 螺杆泵Filter 篩檢程式，濾網Cylinder 液壓缸，圓柱體Valve stand 閥台Accumulator 蓄能器Leakage 洩漏Product 產品Grade 鋼種Batch 一爐，一批Batch No. 爐批號Coil 鋼卷Strip 帶鋼，薄帶鋼Sheet 鋼板，薄鋼板Plate 中厚板Physical performance 物理性能Mechanical performance 機械性能Strength 強度Elongation 延伸Flatness 平直度Plasticity 塑性Crown/chamber 凸度Hardness 硬度Microstructure 微觀組織結構Austenite 奧氏體Ferrite 鐵素體Pearlite 珠光體Deep drawn 深沖SPHC 普通級熱軋鋼板（卷）SPHD 深沖級熱軋鋼板（卷）SPCC 普通級冷軋鋼板（卷）SPCD 深沖級冷軋鋼板（卷）High strength low-alloy steel 低合金高強度鋼Silicon steel 矽鋼，電工鋼Galvanizing 鍍鋅Coating 塗鍍，塗層Heat treatment 熱處理Aging 時效處理Annealing 退火Quenching 淬火Other Alarm 報警Anchoring bolt 地腳螺栓Yield 產量，成材率Ton 噸Annual 一年的Month 月Day 日Shift 班Safety 安全Radioactive hazard 放射性傷害Caution 留意，小心Layout 平面佈置Document 文件Documentation 技術文本，技術檔報價書TOP: take-over point 交接點。

轧钢专业英语单词

HGC 活套张力急停甩尾中浪检修退出 / 推进（操作）轧制力分配热凸度凸度平直度材质轧制规程表压力屈服强度变形区耐磨性横坐标空气喷射自动踏步控制排成直线、列队、对中电流量退火的能应用的、适用的、适合的增多，重视适合的、特有的相变
67 assembly 69 austenite 71 austenitic 73 axial 75 balance force 77 banding dispenser 79 bank 81 bearing cage 83 bearing shoes 85 bracket 87 bronze 89 buggy 91 butt gauge 93 cam 95 cambering profile 97 capable 99 carburized 101 carry over table 103 centerline 105 chamber 107 choke liner 109 chute 111 clean-up device 113 cobble catcher 115 coil conveyor 117 coil lifter 119 coil marking machine
执行轧制数据卷取完成时间板坯号钢种家族温度宽度重量终轧温度化学成份硅磷镍铜钼钒稀土元素总称钨铅锑酸溶铝氮氢密度（带钢）头部/中部/尾部（带钢）的出炉温度用中心线处所测温度值
81 MFG 2 ( 83 F1E ( before F1 Edger Roll ) 85 Max. ( Maximum ) 87 Ini. ( 89 Roll No. ( Roll Number ) 91 Bot - WR ( Bottom Work Roll ) 93 Bot - BUR ( Bottom Backup Roll ) 95 Gap 97 Force 99 Torque 101 R - Speed ( Rolling Speed ) 103 WRS ( Work Roll Situation ) 105 ISC ( Instand Cooling Water ) 107 WR - Speed 109 Quality Chart Display 111 Flatness 113 Discharge 115 Flatness Meter Profile

轧钢词汇-working

轧钢词汇AV-鞍座式V-head type鞍形卷座，带卷存放鞍座coil storage saddle凹痕,泡痕,陷窝(钢板粘结时的) dimples dent 凹陷shallow surfacedefect凹形辊身concave barrelB摆动溜槽swinging spout摆动式砂轮pendulum grinding machine 摆动台tilting table摆剪机pendulum shear摆式剪pendulum (rocking) shear 板、带材的中心凸厚部分, 轧辊凸度crown板材flat product板凳(换轧辊用) mock-up板管比plate, strip and pipeortion板卷coiled sheet板卷拆印（板卷表面缺陷）coil wrench mark板坯(初)轧机slabbing mill板坯，扁坯slab板坯出料机slab extractor板坯处理slab disposal板坯存放区slab storage area板坯垛挡板slab pile dumper板坯返回辊道slab reject table板坯-方坯初轧机Slabbing and Blooming mill 板坯分垛机slab depiler板坯厚度slab thickness板坯里外温差temperature variation fromsurface to core of the slab 板坯连续加热炉continuous slab reheatingfurnace板坯清理设备slab conditioning device板坯受料装置slab receiving device板坯弯曲slab buckling板坯修整机slab-conditioning machine 板坯运送车slab buggy板坯轧机slab mill, slab squeezer 板坯转运车slab transfer car板坯自动出料automatic slab discharging 板式（链板）运输机apron (palled) conveyer 板式滤网plate-screen半封闭炉covered furnace,-closedfurnace半钢工作辊adamite work roll半连续热带轧机semi-continuous hot-strip 半连续式轧机combination finishing mill 半联轴节, 偏接轴的扁头coupling half半门吊车, 半门形吊车semi-gantry crane半圆集料架（冷床的）cowhorn bins棒材，条钢，型钢steel bar棒材拉拔机bar bench棒线材轧机bar and rod mill邦迪管，铜焊管Bundy tube包装，打捆packing包装和捆扎线packing and binding lines 包装跨packing bay保护环protector保护气氛protective atmosphere保护气体atmospheric gas保护气体设备protective gas plant保温温度holding temperature鲍曼硫印Banmann printing贝壳状断口conchoidal fracture贝氏体, 贝茵体bainite备件spare part备品库spare stock house备用件和磨损件spare and wear parts 背，后面，支持，承托back背面照明光源装置Backlighting light sourcesystem倍尺multiple of the final length 泵油装置oil jacking-up device比热heat specific闭环控制close loop control闭口(开口)腿closed (live, open) flange 闭口架closed head闭口孔型，直轧闭口孔型tongue-and-groove pass 闭口孔型轧制tongue-and-groove rolling 闭口式孔型轧制法，闭口tongue-and- groovemethod孔直轧法闭口轧槽closed (deal) groove闭路系统closed loop system敝开退火，黑退火open annealing壁厚公差wall thickness tolerance 边部裂纹(带材的) checks边脚料管（剪切机旁），搬运箱tote box边切剪end trimming shear边缘控制装置(防跑偏装置) EPC (edge position controlling unit)边缘位置的扫描控制scanning edge positionol边折（带钢缺陷）edge break扁材flat product扁材热轧机Hot rolling mills for plateproducts扁钢，板片，平板条flat bar, flat steel, strip bar扁钢轧材flat products扁坯flat blank扁型磨轮修整装置flat type grinding wheel truingdevice扁圆坯(轮箍坯) cheese便携式线盘wire carrier变（直）径管stepped tap, reducer变截面板簧轧机multiple-section flat springrolling mill变形特性deformation characteristics 标记打印机marker, tag printer标距gage length标签框题字inscription in tag frame标准负荷normal-duty标准机械液压油normal mechanicalhydraulic oil表面处理surface-conditioning表面处理技术surface treatmenttechniques表面粗糙度，表光洁度surfaceroughness表面光洁度surface finish表面黏结条痕（带钢处理缺陷）strikerbreak表面起网状裂纹surfacechecking表面缺陷surface defect表面温度计，光测高温计ardometer表面修整，表面清理surfaceconditioning表面压光机，平整机skin pass mill 表面硬化case hardening表面状态（况）surface appearance表压gauge pressure丙烯醛（钢丝上肥皂润滑剂燃烧的）生成acrolein 拨卷机，推卷机coil ejector, coil kick-off 拨料机，拨料器kickout, kickoff, pick-uparms, ejecting device,kick-out device, diverter 拨料爪drag-on dogs拨爪pusher dogs波纹管corrugated pipe波纹膨胀箱expansionbellow剥皮scalp剥皮(修整)机床scalpingmachine剥皮车床peeling lathe薄(厚)壁钢质导管Light (heavy)-wall steelconduit薄板sheet, light gauge sheet 薄板测厚仪sheet thickness calibrator 薄板层产品light-coated products薄板打捆装置sheet packing device薄板打印机sheet printer薄板辊式冷矫直机cold mangle薄板和镀锡板平整机sheet annealing base薄板冷轧机cold-sheet mill薄板坯thin slab, sheet bar,sheet billet薄板坯连铸连轧机thin slab continuouscasting and rolling(conroll) machine薄板轧机sheet mill薄壁管thin wall tube薄壁喷灌管Thin wall sprinklingirrigation tube薄钢板退火（固定式）炉台（炉底）补风设备make-up air equipment 不等边角钢unequal angle, L-bar,unequal triangle steel不定尺，任意长度random length不过端规no-go gage不合标准的废钢铁off-grade scrap不合格板off-gauge sheet不合格带卷，报废带卷reject coil不合格料off-size material不合格率occurrence of off-gauge 不加厚non-upset不均厚度uneven gauge不平度(钢板) flatness不同程度层产品differential coated product 不完全燃烧imperfect combustion不完全退火slack annealing不完全硬化slack hardening不锈钢板坯stainless steel slab不锈钢带材stainless steel strip不锈钢管stainless steel tube不锈钢卷stainless steel coils不再加热的方坯unreheatedbloom布氏硬度brinell hardness步进底式加热炉working hearth typereheating furnace步进梁walking beam步进梁式炉walking beam furnace步进式炉walking-beam typefurnaceC擦伤(带钢缺陷) gauge擦拭辊wiper rolls材料跟踪materialtracking材料流程material flow彩电用荫罩钢网stainless steel forshadow-mask of colourTV set彩色镀塑金属构件coloured plastic coated metal structure members彩色有机涂层钢板colour organic coated steel sheet参观走道visitors observationwalkway仓库storage操作机manipulator操作平台operating platform 操作室Control House槽,出料槽,漏斗(喇叭形),焊管拉模gutter, welding gutter槽杆式油压操作lever type oil hydraulicoperation槽钢channel, channel bar,U-bar, channel steel槽钢(小尺寸的) channel bar槽式运输机troughconveyor侧传送辊道side shift table侧导板side guide侧导板推床sideguard manipulator侧立卷筒gravity inverted block侧喷水器side spray侧卫板，导板guide侧卸式送锭车side tilt car侧压力lateral pressure侧压下（轧制时的）indirect rolling action侧移小车side shift car测长仪length measuring machine 测长装置length measuring device 测厚仪gauge meter, thicknessmeter, gagemeter测压计，压力计pressure gauge测压仪，测力计，发送器load cell, measuring cell,pressure cell层流带钢冷却系统Laminar flow strip coolingsystem插值器，解算装置digital differencedetector差动齿轮differential gear差压开关Differential pressureswitches拆炉机demolishing machine缠乱，反盘snarl缠绕试验coiling test产量production, throughput,output rate产品大纲，产品方案product mix产品更新换代product replacement andupdate产品和规格方案product and size mix产品开发product development铲凿清理台（锭，坯缺陷）chipping bed长度length长耳子(板、带材的端部缺陷) long ears, long lug 长型换辊套筒poster bar, perter bar长焰及可调火焰烧嘴long flame and adjustableflame burners长轴驱动辊道lineshaft driven rollertable常化normalizing常化炉normalizing furnace,annealing furnace常化酸洗机组，连续酸洗机组CP line(continuouspickling line),Annealing-pickling line 常温常压normal temperature andpressure (NTP.)常温压制，冷压cold-compacting敞开（黑）退火open annealing超弹性变形hyperelastic deformation 超导材料superconducting material 超定向电工钢，高级定向电工钢super orientedelectrical steel超精密扁丝压延机ultra-precision flat wiremangler超平整产品extra-smoothed product 超深冲性能的冷轧薄板cold rolled sheets of extradeep drawing quality超声波焊接ultrasonic soldering超声波检测ultrasonic test超声检查ultrasonic inspection超硬材料extra-hard material超运转离合器over-running clutch超重负荷UHD (Ultra-Heavy-Duty)车底式加热炉reheating furnace withmovable hearth车底式炉car hearthfurnace车底式热处理炉car-bottom batch-typefurnace车轮轮幅压弯机dishing press车轮轮箍railway wheel tyre, railtyre车轮轮箍轧机railway wheel and tyremill车轮模锻压力机wheel forging press车轮坯wheel blank, wheel block 车轮轧机railway-wheel mill, diskmill车式冷却(热轧带卷的)运输机car-type coolingconveyer车丝机(接插) threading machine,tapping machine车载批量carload lots车装重量公差carloadtolerance沉淀槽settling bath,sedimentation tank沉淀池（氧化铁皮的）settling basin,sedimentation basin沉淀硬化precipitation hardening 沉降槽settling tan沉降池，沉积池settling basin衬锡的tin-lined称量辊道scale roll table称量设备weighing equipment称量装置weighingmachine撑套杆looper arm成材率，收得率yield成卷带材的端头coil tail成卷带钢coiled steelstrip成卷退火,成盘退火（线材）coil annealing成卷轧制coil rolling成捆in bundle成盘条钢，盘圆coiled bar成品包装跨packing bay成品仓库product storage成品储存场product storage yard成品发送区dispatch department成品发运跨dispatch (dispatch) bay,loading bay成品检查台架finished productsinspection stand成品卷product coil 成品卷筒（拉拔机的）final capstan成品收集筐loading cradle成品线卷筒finishing block成品轧机，精轧机finishing mill成套供应supply in fullsets成形辊（带材导入多辊卷取机用）coiler roll承载梁carrier bar秤量（磅称）车scale car弛度控制（带钢的）catenary control尺寸公差dimensional tolerance尺寸偏差dimensional deviation齿顶，螺纹顶部crest齿根，螺纹根部root齿辊轴chunk-breaker shaft,disintegrator shaft齿距pitch齿轮型联轴器gear-typecouplings齿条（冷床的），缺口式棒notched bar齿条式冷床notch-bar cooling bed,notch-bar hot bed,rake-type cooling bed齿形profile齿形接手，多槽花键轴multiple spine shafts翅管式金属换热器fin tube type metallicrecuperator冲床stamping press冲动和穿带速度jogging and threadingspeed冲击荷载shock load冲击韧性impact ductility冲孔模piercing die冲孔柱塞piercer plunger冲头piercing head冲压用优质冷轧薄板cold-rolled drawing qualitysheet冲氧化铁皮水泵scale pusher water pump 抽出机extractor抽出装置drawing-out device,withdrawing device抽风干燥段风箱downdraftdrying wind box抽风干燥机downdraught dryingsection抽风用风机exhaust fan抽风预热段downdraft preheatingsection抽风预热段风箱downdraft preheat windbox抽风总管wind main抽头wapping off出钢口（嘴）discharging spouts出口侧自动捆卷机Delivery automatichandling machine出口导板盒delivery guide box出口导卫型卫板stripper type guide出口端exit ends出口夹送辊delivery pinchroll出口速度exit speed, delivery speed 出口卫板delivery (exit, outlet)guard出料discharging出料拔杆kick-out arm出料辊道discharge roller table出料活套塔（或坑）outfeed accumulator出料机discharging machine,extractor出料炉门dischargingdoor出料台架discharging table,delivery table出料推杆(冷床的) kick-off arm, kick-out arm 出炉辊道furnace deliverytable初次厚氧化铁皮primary heavy scale初次轧制，毛坯轧件initialbreakdown初生坯壳increased shell初验check analyses初轧，开坯to cog down, cogging初轧板坯翻转吊车slab turning gantry初轧翻转装置bloom turnover device初轧方坯bloom, cogged bloom初轧机开坯机bloomer, blooming mill,breakdown mill初轧机用轴承bearing for blooming初轧坯bloom初轧坯打印机bloom stamping machine 初轧坯夹钳bloom clampingtongs除鳞descale除鳞泵descaling pump除鳞机，破鳞机descaler descaling mill,descaling mill除鳞系统的防震流水孔口watershock-prooforifice ofdescaler除丸（风力）shot-removing blast除锡，脱锡detinning除锡装置detinning apparatus除氧化铁皮箱descaling box触媒剂，添加剂addition agent穿出（带材）threading out穿带导板threading guide穿带导卫台threading guide table穿带杆threader bar穿带和甩带操作threading andunthreading operation穿带速度threadingspeed穿带台threading table穿带自动控制装置automatic threadingcontrol device穿孔（性）能力pierceability穿孔，穿轧piercing穿孔顶头piercing point穿孔机piercer mill, piercingpress piercing machine穿孔机(狄赛尔) Diesher piercing mill穿孔机下模，底座，台架，冷床，基础bed穿孔机轧辊piercer rolls穿孔挤压piercingextrusion穿孔毛管pierced billet, piercedshell穿孔温度piercing temperature穿孔芯棒piercing point bar, piercerbar, piercing mandrel穿模（拉丝用），引线threading up穿入（钢带）threading in穿梭式小车shuttle carriage穿靴筒（钢锭缺陷）bootlegging穿引料杆threading bar穿引速度threadingspeed穿轧过孔的坯料pierced billet, hollow body传动侧机架open-top rollhousing传动辊live roll, driven roll,forcing roller传动夹头driving dog传送小车，送锭车transfer bogie, transferbuggy (car)船板ship plate串联（梯流）式布置cascade串列(粗轧)-横列(精轧) combination finishingmill联合精轧机窗框钢 sash bar 窗框钢连轧机 sash section mill垂直度 squareness 垂直压下（轧制时的） direct rolling action 锤击展薄,碾轧 becking 磁畴论 domain theory 磁粉检查 magnetic particle inspection 磁力吊车magnet crane 磁力吊车式分垛机;钢板磁力分垛机 magnet-crane depiler磁力垛板机magnetic sheet handler, magnetic sheet piler magnetic sheet bandler 磁力阀magnetic valves次品，不合格产品，废品，筛粗料，尾矿 sub-quality product reject, reject material, rejectproduct从炉中出锭 drawing of ingot 粗调 coarse adjustment, rapid adjustment粗挤压breakdown extrusion 粗拉伸（拉丝）机 breakdown drawing machine粗圆坯孔型 primary round pass forms 粗轧板坯 breakdowns粗轧机 roughing mill, rougher 粗轧机组roughing mill group 粗轧破鳞（除鳞机） primary scale breaker 粗轧破鳞机 scale breaker of rougher 脆性 embrittlement, brittleness 淬火quenching, quench, hardening淬火槽（轧件）水冷槽 quench bath, quench(ing) tank淬火处理 quenching treatment 淬火的 quenched淬火—断裂试验 quench and fracture test 淬火回火 quench tempering淬火—回火处理 quench-draw treatment 淬火机quenching machine 淬火机机头，淬火喷头 quench head 淬火计 quenchometer 淬火剂 quenchant, quenching agent, hardening agent淬火介质 quenching media淬火空位 quenched-in vacancy 淬火炉 hardening furnace, quenching furnace 淬火炉装置 quenching furnace arrangement 淬火敏感性 quench sensitivity 淬火能力 quenching power淬火强度 quenching intensity 淬火软化处理 quench annealing淬火设备 quenching equipment 淬火时效 quench aging 淬火时效硬化 quench age hardening 淬火试验 quenching test 淬火水 quenching water淬火速率 quenching rate 淬火索氏体 quenched sorbite淬火条件 quenching conditions 淬火弯曲试验 quench bend test淬火温度 quenching temperature 淬火箱 quenching tank 淬火效应 quenching effect淬火液 quenching liquid淬火应变 quenching strain淬火应力 quenching stresses 淬火硬化 quench-hardeni ng淬火油 quenching oil 淬火罩quenching hood 淬火装置（轧件浸渍） quench unit 淬火状态 quenched condition 淬火作业线 quenching line淬火作业运送带 quench conveyor淬裂，淬火裂纹 quench cracking, quenching crack 淬透性 quenching degree淬硬层深度 depth of hardening zone 淬硬钢 chilled steel淬硬合金钢 quench alloy steel淬硬和磨光钢板 hardened and surface ground steel plate存储台（轧材）storage bed 错压下miss rollingD搭焊管lap-weldedpipe搭焊管机lap-weldedmill搭接炉焊管机lap-welded pipe mill达到国际同类产品水平have caught up tointernational levels打包，打捆，（板材）堆垛baling打包钢带baling band打包钢丝baling wire打包机baling press打包用带钢轧机package mill打包窄带钢baling strip打包窄带钢;箍圈hoop打结试验（钢丝）snarl test打捆banding打捆(包)机bundling machine,bundler, bander打捆设备bundling equipment打捆运输机banding conveyor打盘机coil winding machine 打印mark打印机stamping machine,stenciling machine,marking machine,stamping unit,markingapparatus打印台stampingstation打轴机(钢丝) winding apparatus打桩piling大(中、小)型型钢轧机heavy(medium, light)section mill大导盘rotating guide disc大导盘穿孔机Diesher piercing mill大导盘轧管机，狄塞尔轧管机Diescher mill大厚度剪切机组heavy shearline大厚度纵剪机组heavy slitting line大开度板坯轧机high lift slabbing mill大口径超薄壁不锈钢管large diameter ultra-thinwall stainless pipe大口径管子large-diameter pipe大量的原料enormous amounts ofraw material大升程high lift大升程板坯初轧机high lift slabbing mill 大升程初轧机high-lift blooming mill大体积混凝土施工bulk concreteconstruction大型钢large section, heavysection大型轨梁轧机Large structural shapemill大型坯bloom blank大型外圆磨床heavy duty circulargrinder大型卧式离心浇铸机large-sized horizontalcentrifugal castingmachine大型型材轧机large shapemill大型轧机heavy-section mill大修overhaul (general,major, capital, heavy,big) repairing, majormaintenance大压下量heavyreduction大圆弧刀片curved blade带V型托台的带卷运输车camel backcar带材波纹ridge buckle带材初轧机band roughing mill带材端头嵌入strip end engaging带材缝合机stitcher带材和卷材进料自动高速压床strip and coil feedautomatic high speedpresses带材矫直机coilstraightener带材精整作业线strip processing line带材静电涂油机electrostatic strip-oilingapparatus带材卷，线卷，盘条，绕组coil带材卷取机ribbon reel, coiling reel 带材卷取温度coiling temperature带材卷取装置strip coiling apparatus 带材拉断strip breakage带材冷轧机cold-strip mill带材平整机coil tempermill带材热轧机Hot strip mill带材退火strip annealing带材下垂sag of strip带材张紧装置drag bridle带岔道的切头溜槽crop end chute withswitch带弹簧的手动压下装置manual screw down withspring带调整螺钉的进口导板盒screw box entryguide带反问链的冷床simple chain coolingbed带钢strip带钢，热轧带钢hoop带钢边缘位置检测器Strip edge positiondetector带钢存积设备strip storing equipment 带钢导向挡板strip guideapron带钢拦截装置，带钢挡板strip catcher带钢冷却喷水器strip cooling sprays带钢冷却系统strip cooling system 带钢冷轧机cold-strip-steel rollingmill带钢裂口strip cut带钢炉内张力strip tension in furnace 带钢喂入装置strip catcher带钢支承臂strip support arm带钢贮料塔strip accumulator带固定挡板的板坯受料辊道slab pile receiving table with end stop带筋扁钢ribbed flat带锯band saw带卷，线卷，盘条，圈coil带卷（定尺）横剪作业线coil cut-up line带卷（端头）焊接作业线，拼卷作业线coil build-up line带卷（焊管坯）存储台coil magazine带卷（线卷）卷紧法coil compacting method 带卷垛coiled stock带卷磅秤coil scale带卷擦伤（热轧钢板卷间滑动擦伤）coil digs带卷仓库coil storage带卷测量装置coil measuring device 带卷板直机coil opener带卷长度coil length带卷称量秤coil weighing scale带卷称量系统coil weightingsystem带卷秤，带卷称重装置coil weighing machine,coil weighing scale带卷尺寸coil size带卷抽出小车coil extraction car带卷处理coil handling 带卷打包机coil banding machine 带卷打捆站coil banding station,coil base带卷打捆装置coil strappingdevice带卷单垛退火single stack coilannealing带卷定心coil centering带卷镀锡前的预整（矫直，焊接，切边，检查）作业线coilpreparationline, coilingline带卷端头coil end带卷端头板直机，带卷直头机coil-tailing device,pulling device带卷端头喂送装置coil end feedingdevice带卷堆场coil yard带卷翻倒装置coil overturn(ing) device,coil-upender,coil-up-enderattachment带卷防撞器coil bumper带卷分离器圆盘coil separator disc带卷分离装置coil branchingdevice带卷高温罩式通火机组电气室 C.B.E.R.(coil batchannealing lineelectrical room)带卷焊接机组电机室 C.W.E.R(coil weldingline engine-room)带卷焊接机组作业线coil weldingline带卷缓冲辊coil snubberroll带卷回转装置coil turning device带卷架coil frame带卷检验室coil inspection room带卷接收器coil receiver带卷开卷coil unwinding带卷开卷（进料）箱coil box带卷宽度自动对中装置automatic coil widthcentering device;automatic coil widthcenter unit带卷捆紧装置coil tightening device带卷捆扎机coil banding machine 带卷磨光coil grinding带卷平整擦伤coil temperdigs带卷起重夹钳coil tongs带卷取机的保温炉，卷取炉coiler furnace, coilingfurnace带卷圈数（的增加）增大coil build-up带卷热平整机作业线coil thermal flat line带卷升降车coil jack带卷升降回转台coil lift-and-turn unit 带卷升降机coil hoist带卷升降台coil lifter带卷输入（储存）台（开卷机旁）coil entry ramp带卷输送台coil delivery ramp带卷输送装置coil carrying device带卷酸洗机组 C.P.L(coil pickling line) 带卷套入（卷轴）coil insertion带卷推出器，卸卷机（卷取机的）coil pusher, coil pushing-off device带卷退火机组Coil annealing line带卷退火炉coil (annealing)furnace带卷退火作业线(生产线) coil annealingline带卷外径coil outside diameter带卷芯子coil core带卷旋转装置coil rotating device带卷移送车coil transfer buggy, coiltransfer car带卷移送机coil transfer带卷台架coil skid带卷移送升降机coil transfer lifter带卷引进端leading end of coil带卷引头检测器coil leading detector带卷预整装置coil preparation unit带卷运出台（卷取机旁）coil delivery ramp带卷运输车coil conveying truck,coil carriage带卷运输机coil conveyer带卷运输机室 C.C.E.R.(coil conveyorelectrical room)带卷运送车coil transfer car (buggy),strip handling car带卷运送机coil transfer带卷运送装置coil carrying device带卷支持器;线卷支持器;开卷;线架coil holder带卷支座的（悬臂）卷筒coil holderhead带卷直径coil diameter带卷直径测量装置coil diameter measuringdevice带卷直头机（插入）coil opener, coil peeler,coil opener chisel带卷直头机摆动装置coil opener swing device 带卷直头机錾coil openerchise带卷重量coil weight带卷贮存跨coil stockingbay带卷转向辊coil turning roller带卷装料台coil loadingskid带卷装卸车，（开卷机和卷取机旁）coil car带卷装卸车调挡coil buggyshift带卷装卸台（开卷机旁）coil ramp带卷装卸装置coil-handling equipment 带卷准备站coil preparatory station 带卷自动称量装置automatic coil weighingsystem带卷自动喂进系统Automatic coilfeeding system带卷自动装卸车，升降运输车coil car带卷座（开卷机的）coil cradle带前张力（冷）轧机（带卷）coiler tension rolling mill 带收集装置的冷床stacking bed带锁口的钢板桩lock sheet pilingbar带提升夹钳的半龙门吊semi-gantry crane withlifting tong带凸痕的轧辊Dented roll surface带围盘（的）轧机guide mill带尾自动停止装置automatic coil tail endstopping device带芯冷拔(生产毛细管) core drawing单臂龙门刨床opensided doublehousing planer单次拉丝机bull block单独传动individualdrive单独传动辊道individual drive table单独电机传动(减径机) electric individual drive 单镀层产品single coated product 单垛连接退火炉single stack annealingfurnace单垛式炉台single-stack base单轨钩式运输机monorail type hookconveyer单机架平整机single stand skinpassmill单卷单垛退火single stack coilannealing单链mono-chain单链拉拔机single chain typebench单链式冷床single chain coolingbed单梁吊车single beam crane单面(双面)料架立柱single(double)column 单面冷床single-side (hot)bed单面料架立柱single column单钳口筒式(炉用)卷取机single-slot mandrel typecoil单体设备individual piece ofequipment单位面积specific area单位压力unit pressure单向轧机，不可逆式轧机unidirectional mill弹簧扁坯flat springblank弹簧式接轴托架spring loaded spindlecarrier弹簧式上辊平衡装置top roll spring balancearrangement弹性elasticity弹性后效elastic after-effect氮化硅结合碳化硅制品silicon nitride-bonded carbide product氮氢混合站N-H mixing station挡板，停止器stop, stopper挡板架damper frame挡板式切断油装置oil damper type breakingdevice挡管器tube stopper, hold back 挡料给料机stopper-feeder挡头stop刀杆轴arbor shaft刀鼓直径knife drumdia.刀架tool slide刀片（剪切机的导板）叶片blade, knife刀片侧间隙blade side clearance刀片定位装置knife aligning device刀片滑块(下),下滑架(bottom) knife head刀片滑块，滑动刀架knife block刀片架blade holder刀片配置盘knife set upbase刀片斜度blade rake刀片重合度blade overlap刀刃更换筒夹cartridge for knifechanging导板guide apron, guideblocks, former bar导板支承梁，(轧机牌坊的)横梁rest bar导板车间Guide shop 导板根部guard heel导板盒guide box, guidecage导板梁bridging plate导板台sticker box导板箱guide box导槽guide groove导杆guide bar, guide pole,guide rod导管，导引管guide conduit导轨guide rail导轨滚轮，导辊，导轮guide roller导辊guide roll, guide table,guide barrel导滚桶guide barrel导环guide ring导块guide blocks导轮guide wheel (pulley)导盘disc, guidedisc导绳guide rope导卫安装（调整）工guide setter导卫板（穿孔机）guide shoe导卫划痕（轧件缺陷）guide scores, guidescratch, guide marks导卫剪伤guideshearing导卫轧制guide rolling导卫轧制圆钢guide rounds导卫装置guide and guards,guide fittings导线盒snatch box导向（表面）guide surface导向板guide plate, deflectorapron导向档板deflector, deflector gate,deflection apron导向杆sweep arm导向杆（槽，轨，板）guide, guiding bar(groove, rail, plate)导向轨座（机座可沿其移动）sliding base导向辊(带纠偏装置的辊) steering roll导向滑动（横梁）guidecrosshead导向滑条式冷床skid-type hot bed导向架guide frame导向漏斗，导锥guide cone导向螺栓guide bolt导向螺丝guide screw导向设备pilot plant导向台guide table导向弯曲（弯道）guided bend导向弯曲试验guided bendtest导向弯曲试验夹具guided bend test jig导向轴承guide bearing导向轴套（套管）guide sleeve导向装置，导卫板guide piece导叶（片）guide blade导轴guide spindle, guide axle 导轴衬（套）guide bush导柱guide column, guidepost倒角边（焊管坯的）bevel edge倒棱chamfering倒棱机beveling machine,chamfering machine倒立式收线机upside down coiler倒圆blending倒装upside down charging 倒锥铸造inverse taper cast等边角钢equilateral triangle steel,equal angle等静压冷成型cold isostaticcompacting (orcompaction)等离子弧切割机plasma cutting machine 等流阀flow-equalizing valve等外品，不合格品off-gauge product等外轧材(指尺寸)缺尺off-gauge material等温淬火austempering等温退火isothermal annealing低合金钢low alloy steel低合金管low alloy, light alloy(steel) tube低松驰预应力钢绞线（钢丝）low-relaxation prestressed steel wire低压开关low pressure switch滴落量，回流量drainage狄赛尔导盘Diescher disc.狄赛尔轧管机Diescher mill底板，地板脚，轨座，底座，辊道传动侧框架bedplate底层under-coating地道通风装置ventilation for subway 地脚板，底板，主底板main base 地脚螺栓foundation bolts地上卷取机up coiler地上运输机floor conveyer地下槽cellar tank地下卷取机down coiler地下连续墙钻机underground continuouswall drill地下室basement, undergroundroom地下油库oil cellar地下运输机tunnel (underground)conveyer, tunnel coiler 地下运输机(热带卷的) underground conveyer,tunnel conveyer点变形point deformation点焊机spot welder电磁超声自动探伤装置automaticelectro-magneticultrasonic flow detector 电磁吊cranes provided withload magnets电磁阀electro-magnetic valve,solenoid valve电动(手动)压下装置electric (hand)screwdown gear电动上辊压下装置electric top rollscrewdown电动上切式剪切机Electric down-cut shear 电动四轮小车electric motor driven4-wheel carriage电动筒泵motor-driven barrelpump电动铣刀motor-driven millingcutter电动液压伺服阀electro-hydraulic servovalve电镀锡tin-electroplated电镀锡钢板和带卷electronically tinnedsteel sheets and coils 电火花切割机electrospark cuttingmachine电机室Motor Room电解槽electrolytic bath, platingcell电解镀锡法Electrolytic tinningmethod电解镀锡钢板生产线ferrostan-typeelectrolytic tinning line 电解镀锡线Electrolytic tinning line(E.T.L.)电解镀锌生产线Electrolytic galvanizingline电解清洗grid cleaning电解去油（脱脂）electrolytic cleaning电解酸洗electrolytic pickling电解脱脂槽electrolytic degreasingbath电桥臂(测定用) bridge arm电热室，电预热室electric heating chamber 电视摄（录）相机television camera电渣焊electroslag welding电渣焊机electroslag welder电阻焊管resistance welded tube,ERW tube电阻焊管轧机electric resistance weldpipe mill电阻焊接机resistance welder电阻加热软熔装置resistance heatingreflow device吊车, 起重机crane吊车挂钩工tagman吊车轮压crane wheel loads吊轭suspension yoke吊耳，(复)耳子ear吊挂式运输机overhead conveyer吊挂卫板balanced guard吊线架，吊线机gallows吊运小车travelling jack carriage 调度室dispatching room调节螺栓adjusting screw调整垫片（剪机本体部件）shim调整机构adjusting gear调质处理hardening andtempering treatment调质钢quenched and temperedsteel叠板堆垛吊车（带吊运托架的）piling crane叠板热轧机hot-pack mill叠轧的pack-rolled顶杆mandrel bar顶杆小车，止推小车thrust block (carriage) 顶管机CPE (cross piercing andelongation) mill, pushbench顶头plug顶装烧咀ceiling-mounted burner 定尺cut-to-length定尺长度exact length, cut length 定尺挡板cut length stopper定尺剪dividing shear定尺剪切线cut-to-length line定尺剪切作业线cut-to-length shear line 定尺锯cut-to-length saw定尺拉头gauge head定尺飞锯数控系统digital control system ofcut-to-length flying saw 定公差切割cut-to-tolerance定径机，定宽压力机sizing mill, sizing press 定径区长度，阴模工作区bearing length定期复验periodic recheck定时器，调时器time clock定位辊道aligning conveyor定位器tube locator定向螺旋无缝钢管seamless tube withinternal oriented spiral 定心车床centering lathe定心辊装置Steadier, cluster定心机centering machine定心圆锥式开卷机cone-type feed reel定颜剂color fixative in paint锭模车mold car丁字钢T-bean\m, T-bar, flangebeam动齿条（冷床的）carry-over bar动力剪切power cut动力助拧器power sizer动态厚度变化模拟试验dynamic gauge changesimulation test斗式链轮卸料机bucket wheel unloader 镀槽，电镀槽plating tanks, coatingbath镀层薄板coated sheet镀层厚度测量仪coating thickness gauge 镀铬与衬胶车间chrome coating andrubber lining shop镀铝锌galvolume镀铅槽，铅淬火槽lead bath镀锡tin(ned) coating, tinning 镀锡板tin(ned) plate, tinnedsheet镀锡板斑点tinplate patches镀锡板设备tinplate facilities镀锡薄板精整工段tinplate finishingdepartment镀锡薄钢板tinplate tin(ned) sheet,tin(ned) steel镀锡薄钢板板坯tinplate bar镀锡薄钢板切边tinplate cuttings镀锡薄钢板轧机tinplate mill镀锡薄钢带tinplate strip镀锡不锈钢丝tinned stainless-steelwire镀锡槽tin(ning) bath镀锡车间tinning plant镀锡带钢tin strip镀锡的tinned, tin-plated,tin-plating镀锡钢丝tinned wire镀锡辊tinning rollers镀锡锅tinning pot, tin pot镀锡机tin machine, tinning unit 镀锡铝线tinned aluminum wire 镀锡前酸洗tin pickling镀锡铜铰线tinned stranded copperconductor镀锡线tinning line镀锡原板uncoated tinplate base 镀锌zinc coating, zinccovering, zincing,galvanizing, zinc-plating 镀锌板galvanized sheet,zinc-coated sheet镀锌薄钢板zinc-coated sheet镀锌薄钢板和带卷galvanized steel sheetsand coils镀锌槽galvanizing (spelter)bath, coating pot, zincbath镀锌槽，锌溶槽zinc bath镀锌层galvanizing coat, zinccoating镀锌层测厚仪zinc coat thicknessgauge镀锌电解液zinc solution镀锌钢板galvanized steel sheet 镀锌钢管galvanized steel pipe 镀锌钢丝zinc-coated wire,galvanized steel wire 镀锌管galvanized pipe镀锌锅zinc pot镀锌炉zinc-coating furnace镀锌显晶塔spangle tower镀锌线Galvanizing line端部式送锭车end tilt ingot car端头板直的带卷tailed coil端头－废料剪(切机) crop and cobble flyingshear短应力线short stress path,housingless roll stand,reduced ring stress短应力线轧机double-duo short stresspath mill断辊roll breakage断口，裂缝，折断fracture断裂负荷breaking load断面（型钢）sectional shape锻炉，锻造炉forge锻坯forging ingot堆板箱piling box堆板机，堆垛装置piling device堆垛（冷却）台piling (cooling) bed堆垛车piling car堆垛高度stacking height堆垛机，垛板机piling machine, piler,piler bed堆垛跨piling bay堆垛筐架piling cradle堆垛冷却cooling in packedformation堆垛台piling (cooling) bed堆垛退火，成叠退火pack annealing堆垛用的隔条piler bars堆垛运输带piling belt堆放架（台）piling bin堆放跨storage bay堆焊（有色金属）(non ferrous) beadwelding堆料跨storage bay堆料托运小车drag-off carriage堆取样pile sampling对比仪comparator对称偏心调整symmetrical eccentricadjusting对缝焊管jump-welded pipe对焊管机butt-weld pipe mill对焊机butt welder对角尺寸diagonal size对碳的亲和力affinity for carbon对中辊steering roll对中螺丝centering screw钝化槽passivation tank多层复合板固相轧机cold clad metal rollingmill多齿梳刀multi-tipped chaser多垛式罩式炉multiple stack annealingfurnace多根线材连续退火continuous strandannealing。

轧钢专业词汇

a pay-off reel 开卷A R steel 高温度锰钢a take-up reel 成卷abnormal steel 反常钢; 非正常钢Abnormal Structure Steel 反常组织钢abrasion n．磨损Abrasion-Resistant Steel 耐磨钢abrasive adj 磨蚀的，磨损的，擦伤的abruptly ad 突然的，出其不意accentuate vt．强调，指出acceptance vt．接受，验收; adj．合格的accessory n．同谋，附件，连带accomodate v．容纳，使适应accumulative adj 积聚的，累计的acid corrosion 酸腐蚀adopt vt 采用，收养aerospace n．航空宇宙aesthetic adj．美学的，审美的air-blower 鼓风机akin to 同类的，同族的algebraically n．代数的alignment vt．直线对准；n．成线法，线列，校对alligator vt．皱裂allotropism n．同素异构alloy steel 合金钢alloy 合金alumina 铝aluminium-steel cable 钢铝电缆aluminize n．镀铝Aluminized Steel 涂铝钢aluminum nickel steel 铝镍钢amalgamation 汞齐化ambient n．大气,包围物，背景的，环境ambient n．大气的ambiguous adj．暖味的，不明确的amorphous adj．无定形的，无组织的analogous adj．类似的，模拟的analogy n．类似，相思Anchored Steel Trestle 锚固式钢栈桥angle iron 角钢Angle Steel Ruler 钢角尺anisotropic adj．各向异性anisotropic steel 各向异性钢片anisotropy silicon steel 各向异性硅钢片anneal n 退火annealed metal 退火材料annealed sheet steel 退火薄钢板annealed steel 退火钢; 韧钢annealing v 退火annealing 退火Anticorrosive Aluminium-CoatedSteel Wire 防蚀镀铝钢丝anti-creeping angle steel 防爬角铁antimony n．锑anvil n 砧apparent n．显然，外观appearance n．出现，显露appearance n．外观，表观，可观性appliances n．用具，器具applied load 外加负载applliance n．家具，器具approach vt．接近，引导，研究，靠近，入门appropriate adj 适当的arc and gas welding 电弧焊和气焊arc welding 电弧焊arc-furnace steel 电炉钢arc-welded steel pipe 电弧焊接钢管area of steel 钢筋断面面积; 钢筋截面面积area of structural steel 型钢截面积Armco aluminized steel 阿姆柯渗铝钢Armco aluminized steel 表面浸镀铝钢Armco stabilized steel 阿母柯稳定化钢Armco steel 阿姆柯软钢Armco steel 不硬化钢armor n．装甲ascend v．攀登，上升ascertain vt．确定，查明，探听ascribe vt．归因于，归咎于asphalt n．沥青ASTM(The American Society forTesting and Materials)美国材料实验协会atmospheric corrosion大气腐蚀atomic density 原子密度attach vt．缚，系，结，贴附Austenilic Ni-Cr Stainless Steel 奥氏体镍铬不锈钢austenite 奥氏体austenitic alloy steel 奥氏体合金钢austenitic chromium-nickel steel 奥氏体铬-镍钢austenitic clad steel 奥氏体复合钢austenitic heat-resistance steel 奥氏体耐热钢austenitic manganese steel 奥氏体锰钢; 哈德菲尔德锰钢austenitic Ni-Cr stainless steel 奥氏体镍铬不锈钢austenitic stainless steel 奥氏体不锈钢austenitic steel 奥氏体钢autogenous welding, fusion welding氧炔焊automatic gage control (AGC) 自动厚度控制系统automatic steel 易切削钢automatic-gage-control 厚度自动控制automobile bumper 汽车缓冲器automobile muffler汽车消声器autonomou adj 自立，自主axle n．车轴，轴杆axle shaft steel 车轴钢backup roll 支撑辊backup-roll 支撑辊Bainitic Steel 贝氏体钢Balanced Steel 半镇静钢Ball Bearing Steel Strip 滚珠轴承钢带Ball Race Steel 滚珠轴承圈钢Ball-Bearing Steel 滚珠轴承钢Bamboo Steel 竹节钢筋band n．带卷Band Steel 带钢Banding Steel 带钢; 箍钢bang vt．冲击Bar Steel 棒钢; 条钢bar 板条，条材，型钢barreling n．岩心管，油桶，管炮，套筒basal adj．底部的Basic Bessemer Steel Converter 碱性转炉钢转炉Basic Bessemer Steel 碱性贝氏转炉钢Basic Bessemer Steel 碱性转炉钢Basic Converter Steel 碱性转炉钢Basic Electric Furnace Steel 碱性电炉钢Basic Open Hearth Steel 碱性平炉钢bath of molten zinc 熔锌池Battened Steel Column 双肢钢柱Bauschinger effect 包申格效应Bauschinger 包辛格bauxite 铁钒土beam equation 射束方程Beam Steel Plate 大梁钢板Beam With Compression Steel 双筋梁Bearing Quality Steel 滚珠钢bearing sleeve轴承套Bearing Steel 轴承钢bed 底座Belgian n．比利时人belly 炉腰Bent Steel 挠曲钢筋beryllium n．铍Bessemer Low Carbon Steel 酸性转炉低碳钢Bessemer Mild Steel 贝色麦钢Bessemer Steel 贝色麦钢; 酸性钢Best Plough Steel Wire 铅淬火高强度钢丝betwixt adv．介于两种之间的beverage n．饮料billet n 小方坯Billet Steel 坯段钢; 钢坯; 短条钢billet 坯锭,钢坯Binary Steel 二元合金钢bismuth铋Black Mild Steel Carriage Bolt And Nut 黑铁马车螺丝闩Black Mild Steel Fish Bolt And Nut 黑铁鱼尾螺丝闩Black Mild Steel Flat Head Rivet 黑铁扁头铆钉Black Mild Steel Flat Head Tinmen Rivet 黑铁号头铆钉Black Mild Steel Hexagonal Nut 黑铁六角螺丝帽Black Mild Steel Pan Head Rivet 黑铁锥头铆钉Black Mild Steel Round Head Rivet黑铁圆头铆钉Black Mild Steel Square Nut 黑铁四方螺丝帽black oil黑油, 润滑重油, 重油渣,重油Black Steel Pipe 黑钢板Black Steel Sheet 黑钢皮Black Tin Steel 黑钢板blades n 叶片blank n 冲载模blast furnace 鼓风炉blast furnace 鼓风炉blast 吹扫，清扫Blister Steel 泡钢; 泡面钢bloom n．大方坯Bloom Steel 初轧钢; 钢坯bloom 初轧方坯blooming mill 初轧机blowhole 气孔blowlamp 吹炬(美作:blowtorch)Blue Planished Steel 发蓝薄钢板Blue Steel 蓝钢Bluing Of Steel 钢加蓝blunt adj．钝的Boiler Steel Plate 锅炉钢板Boiler Steel 锅炉钢; 锅炉钢板Boiling Steel 沸腾钢Bolting Steel 螺栓钢Bolts & Nuts For Steel Slotted 角钢螺丝bonding n 连（搭、粘、胶）接Boron Steel 硼钢bosh 炉腹brace n．支柱Brass Fitting Of Steel Window 钢窗铜配件Brass n．青铜Brass-Plated Mild Steel Round BeadWood Screw 镀黄铜圆头软钢木螺丝Brass-Plated Mild Steel Round HeadMachine Screw 镀黄铜圆头软钢机器螺丝Brass-Plated Steel Wire 镀黄铜钢丝break down 变形，屈服，开坯，粗轧Brearley Steel 布里阿雷不锈钢;布氏高铬钢Bridge Steel 桥梁钢Bright And Black Mild Steel FlatHead Tinmen Rivet 号头铆钉Bright Mild Steel Cotter Pin 光亮软钢开尾销Bright Mild Steel Countersunk HeadWood Screw 光亮软钢平头木螺丝Bright Mild Steel Hexagonal Nut 光亮软钢六角螺丝帽Bright Mild Steel Hexagonal Nuts六角光螺帽; 六角螺丝帽Bright Mild Steel HexagonalPressed Nut 光亮软钢六角冲压螺丝帽Bright Mild Steel Round Head WoodScrew 光亮软钢圆头木螺丝Bright-Drawn Free Cutting Steel 光拉自由切削钢Bright-Drawn Steel 光亮拉拔钢材Bright-Finished Steel 光亮精整钢brine n 海水，卤水Brinell hardness 布氏[压球]硬度Bristol Steel Belt Lacing 布瑞斯涛钢带接头Bronze Steel 镀青铜钢brush n 刷掉，电刷bucket n．一桶，铲斗buckle adj．翘曲。

轧钢专业英语

轧钢专业英语Carburizing Steel 碳钢Cast-Steel 铸钢Cast-Steel Pipe 铸钢管Cold-Pressed Sheet Steel 冷压薄钢板Cold-Strip Steel Rolling Mill 冷轧带钢机; 带钢冷轧机Common Straight Carbon Steel 普通碳素钢合金工具钢 Alloy Tool Steel合金结构钢 Alloy Construction Steel碳素工具钢 Carbon Tool Steel高速工具钢 High Speed Tool Steel弹簧钢 Spring Steel工字钢 Ibeam普通圆钢 Round Steel槽钢 Channel扁钢 Flat Steel Bar等边角钢 Equal Angle Steel不等边角钢 Unequal Angle Steelh型钢 Hbeam钢坯 Billet,Bloom钢带 Steel Strip线材 Wire Rod Coil车轮 Wheel Tyre轮筛 Wheel Circlerolling-mill housing 轧机机架bed 底座roller 辊moulded steel 铸钢alloy steel 合金钢bloom 初轧方坯coiled sheet 带状薄板heating 加热preheating 预热tempering 回火temper 回火hardening 淬水annealing 退火reduction 还原cooling 冷却rolling 轧制drawing 拉拔extrusion 挤压wiredrawing 拉丝stamping, pressing 冲压die casting 拉模铸造forging 锻造turning 车削milling 铣削machining, tooling 加工blowhole 气孔Black Mild Steel Hexagonal Nut 黑铁六角螺丝帽Black Mild Steel Pan Head Rivet 黑铁锥头铆钉Black Mild Steel Round Head Rivet 黑铁圆头铆钉Black Mild Steel Square Nut 黑铁四方螺丝帽accelerated cooling 加速冷却accelerated creep 加速蠕变accelerated diffusion 加速扩散accelerated leaching 加速浸出accelerated rolling 加速轧制stainless steel 不锈钢Austenitic Steel 奥氏体钢Austenitic Stainless Steel 奥氏体不锈钢Banding Steel 带钢; 箍钢Bar Steel 棒钢; 条钢Carbon Content Of Steel 钢含碳量austenitic alloy steel 奥氏体合金钢axle shaft steel 车轴钢Cold-Roll Steel Sheets 冷轧钢板无缝钢管 Seamless Steel Pipeiron and steel industry 钢铁工业stamping, pressing 冲压blowhole 气孔Bearing Steel 轴承钢吐丝机和输送机 laying head and conveyor converter变频器，转炉approach table 输入辊道backstepping 逐步退焊法backup roll 支承辊backup roll bending 支承辊弯曲break down mill 开毗机breakdown bar 中间轧坯bumper 挡板bunch 捆bunching machine 线盘捆扎机butt welding 对接焊centrifugal force 离心力centrifugal pump 离心泵centrifugal separator 离心分离器chilled roll 冷硬铸铁轧辊cluster 群cluster mill 多辊轧机;六辊式轧机coefficient 系数coefficient of absorption 吸收系数coefficient of compressibility 压缩系数coefficient of cubic expansion 体膨胀系数coefficient of elasticity 弹性系数coefficient of elasticity in shear 剪切弹性模量cog 初轧坯cogged ingot 初轧坯cogging 初轧cold riveting 冷铆cold rolled band 冷轧带钢cold rolled shape 冷轧型钢cold rolled sheet 冷轧薄板cold rolled steel 冷轧钢cold rolled strip 冷轧带钢cold rolled tube 冷轧管cold repair 冷修continuous cold mill train 连续冷轧机组continuous cooling 连续冷却continuous drawing 连续拉伸continuous drawing machine 连续拉线机continuous finishing mill group 连续精轧机组continuous mill 连轧机continuous roughing mill group 连续粗轧机组continuous rolling 连续轧制crocodile shears 杠杆式剪断机crop 钢锭切头crop bucket 切头箱crop conveyor 切头运输机crop loss 切头损耗crop shears 剪头机cropping 切头cropping saw 切头锯cross roll straightener 斜辊矫直机cross roll straightening machine 斜辊矫直机cross rolling 横向轧制cross rolling mill 横轧机cross rolls 斜辊crank shears 曲柄式剪切机critical density 临界密度critical diameter 临界直径critical grain growth 临界晶粒长大critical load 临界荷重critical mass 临界质量critical nucleus size 临界核尺寸critical point 临界点critical quenching rate 临界淬火速度critical range 临界范围critical shear stress 临界切应力critical speed 临界速度critical state 临界状态critical stress 临界应力critical temperature 临界温度critical value 临界值critical velocity 临界速度。

(完整版)轧钢英语大全

轧钢英语大全轧钢英语Abbrevation English explanationDIS Disable 报废DPC Dynamic Profile Control 动态板形控制DQ Direct Quenching 直接淬火DR Drive 驱动DS Drive Side 驱动侧DSS Double Side Trimming Shear 双边翦EAC Eccentricity Band Adjustment Control Exzentrizitätsband-Nachführung ECC Eccentricity Compensation 离心补偿EHS Exhaust System 排气系统EN Enable 启动ES End shear 终止翦EST Emergency Stop 紧急停止EX Exit Side 出口侧EXS Exit Section 出口区域EY Entry Side 进口侧EYS Entry Section 进口区域FAS First Active Stand Erstes aktives GerüstFC Furnace Charging Area 功能改变区域FL Finishing Line 终点线FLC Flatness Control 平直度控制FM Finishing Mill 精轧机FMS Force Measurement System 压力测量系统FOG Fast Open Gap 快速打开辊缝FU Furnace 加热炉FWD Forward(s) Vor / VorwärtsFX Finishing Stand Fertiggerüst GD Gearless Drive Ringmotor GEN General 概要GLS Grease Lubrication System FettschmiersystemHFG Hot Flatness Gauge PlanheitsmessgerätHGC Hydraulic Gap Control 液压辊缝控制HHSY High-pressure Hydraulic System 高压液压系统HM Hot Mill 热轧HMI Human Machine Interface 人机界面HMS Thickness Measurement System 厚度测量系统HP Hydraulic Position Control (general) 液压位置控制HPL Hot Plate Leveller 热矫直机HRM Hot Rolling Mill 热轧机HSDS Hydraulic Screw Down System 液压压下系统HSG Hydraulic Side Guides 液压侧导板HSM Conventional Hot Strip MillHSY Synchronization of HGC HGC同步HV High Voltage 高电压HW Hardware 部件HWC Hydraulic Width Actuator Control 液压宽度自动控制IB Inspection Bed 检查床IBC In Bar Control In Bar ControlICL Interstand Cooling 机座内冷却IDC Impact Drop Compensation 冲击补偿IDS Interstand Descaling System 机座除鳞系统ILC Impact Load CompensationITC Interstand Tension ControlKSC Kawasaki Steel CorporationKVP Continuous Approvement ProcessLAS Last Active StandLFC Laminar Flow Cooling 层流冷却LMS Length Measuring System 长度测量LS Last Stand 最后机架LSC Load Sharing Control 分载负荷控制LV Low Voltage 低电压LV1 Basic Automation (Level 1) 基础自动控制(L1)LV2 Process Automation (Level 2) 进步自动控制(L2)MM Marking Machine 标记机MCL Manual Calibration of the SDS 为SDS人工计算MGC Motor-driven Gap Control 电机驱动滚缝控制MHI Mitsubishi Heavy Industries 材料重量介绍MHM Materials Handling Machine 材料处理设备MI Manual Intervention 人工干涉MAINT Maintenance Mode 维护模式MMC Man Machine Communication 人机传递MO Manual Operation 人工操作MP Motor-driven Position Control (general)Motorische Positionsregelung (allgemein) MSC Mill Stretch CompensationMSDS Motor-driven Screw Down SystemMSG Motor-driven Side Guides 电机驱动侧导板MSY Synchronization of MGC Synchronisation des MGC MTC Minimum Tension Control MinimalzugregelungMTR Material Tracking 材料跟踪MV Medium Voltage MittelspannungMWC Motor-driven Width Actuator Control 宽度自动控制NA Not applicable 不可用NAS Next Active Stand Nächstes aktives GerüstNEG Negative 否定NT Windows NT Windows NT OFF Off 关OLS Oil Lubrication System 润滑系统OM Operation Mode 操作模式轧钢英语LOGICAL FUNCTION UNIT (LFE) – ABBREVIATIONS逻辑功能缩写ADP Actual data preprocessing实际数据预定AGC Automatic Gauge Control自动辊缝控制AWC Automatic width control自动宽度控制CAL Calibration标度，校准COC Coiler control蛇形管控制CSH Crop shear 平剪CSM Central switching and monitoring主要开关和监控DRA Drive related application驱动请求/应用EGC Electro mechanical gap control电动辊缝控制EMS Emergency system紧急事件系统ETC Edger tension control立辊压力控制FLC Flatness control平直度控制PQE Product quality evolution产品质量进展HGC Hydraulic gap control液压辊缝控制HLC Hydraulic looper control液压环控制HYS Hysteresis test 延迟测试ITC Interstand tension control紧急停止控制ITG Interface to technological Gauges技术测量界面IVI Interface to Visualization形象界面（HMI）LCO Line coordinatorLCS Laminar cooling System层流冷却系统LCT Loop Control环控制LTA Longterm archive adapter存档适配器MAI Manual Intervention 人工干涉MES Media systems 媒介系统MIP Mill Pacing 轧机节奏MOS Model server 服务器模式MRG Master ramp generator主振荡器MSF Mill Support and Sequence Functions轧机维持和次序功能MSM Micro Structure MonitorMTR Material tracking 材料跟踪PAP Plant adapter process 板坯加工适配器PDH Primary data handling原始数据处理PDM Production data manager生产数据管理器PPD Plant production data板坯生产数据PRU Protocol report unitPSH Parameter storage and handling参数存储和处理器PWC Progressive width control宽度控制RAC Roll alignment Control轧机调平控制RBS Roll bending system轧辊弯辊系统RCH Roll change 换辊RSS Roll shift system轧辊窜辊系统SDH Set-up data handling设置数据处理SDS Screwdown system压下系统SCO Stand concentrator机座集中器SIC Simulation Computing模拟处理SIL Simulation Logic仿真逻辑SGC Side guide control侧导板控制SGY Side guide entry (RM)进口侧导板SGX Side guide exit (RM)出口侧导板SSF Stand Support and sequence function机座支持和次序功能SSC Short stroke control短行程控制SSP Slab sizing press板坯精整压力SST Set-up data storage设置数据保存STA Set-up data agent设置数据终端STM Stand control manager机座控制管理器SUF Special Functions 专用功能TFC Thrust Force Compensation推力补偿THC Thickness control 厚度控制WCT Width control 宽度控制XTC Exit temperature control出口温度控制轧钢英语轧机 71 General description概述 71.1 Plate mill approach tables 轧机入口辊道 71.2 Primary descaler 粗除鳞 81.3 Entry & exit turntables 入口、出口回转辊道 81.4 Entry & exit side guides 入，出口侧导板 91.5 Entry & exit feed rolls 入，出口机架辊 91.6 Plate mill main drive 轧机主电机 101.7 Plate mill HAGC capsules (sledge lift cylinder) 轧机HAGC缸（滑板） 10 1.8 Plate mill pass line adjust轧制线调整 101.9 Plate mill back-up roll balance轧机支撑辊平衡 101.10 Plate mill entry & exit top & bottom guides轧机入口，出口上下导卫板 11 1.11 Plate mill spindle balance & latches轧机传动轴平衡和锁紧 111.12 Plate mill spindle carriers轧机传动轴托架 111.13 Plate mill work roll chock latches轧机工作辊锁紧 121.14 Plate mill back-up roll chock latches轧机支撑辊锁紧 121.15 Plate mill back-up roll safety latches轧机支撑辊安全销 121.16 Plate mill entry & exit descaling轧机入口和出口精除鳞 121.17 Plate mill work & back up roll cooling轧机工作辊和支撑辊冷却 13 1.18 Plate mill fume suppression轧机烟尘抑制 131.19 Plate mill work roll change sideshift轧机工作辊换辊侧移装置 13 1.20 Plate mill work roll change car轧机工作辊换辊小车 141.21 Plate mill back-up roll change car轧机支撑辊换辊小车 141.22 Vertical edger main drive 立轧主电机 151.23 Vertical edger entry & exit feed rolls立轧机架辊 151.24 Vertical edger spindle lift立轧机传动轴提升 161.25 Vertical edger roll coolant立轧机冷却 161.26 Vertical edger roll change立轧机换辊 161.27 Runout table轧机输出辊道 162.1.28 Drawings图 172.2 Basic data of equipment ...设备的基本参数 182.3 Start up procedures 启动程序 192.3.1 Preparation prior to start up 启动前准备 192.3.2 Starting of hydraulics液压站启动 202.3.3 Starting of lubrications润滑系统启动 222.3.4 Starting of drives传动启动 242.4 Shut down procedure终止程序 272.4.1 Shut down of drives传动终止 272.4.2 Shut down of hydraulics液压站终止 292.4.3 Shut down of lubrications润滑终止 302.4.4 Stand –by mode for ancillary systems 辅助系统等待模式 31 2.5 Visualization system 可视系统（画面） 342.5.1 General概述 342.5.2 Main displays主显示器 352.5.2.1 Screen format overview 总画面 352.5.2.2 Screen format drives传动画面 362.5.2.3 Screen format pass schedule轧制规程画面 372.5.2.4 Screen format parameter参数画面 382.5.2.5 Screen format mill stand主轧机画面 392.5.2.6 creen format edger立轧画面 392.5.2.7 Screen format roll change换辊画面 412.5.2.8 Screen format calibration标定画面 422.5.2.9 Screen format side guides侧导板画面 432.5.2.10 Screen format roller tables输送辊道画面 442.5.3 Screen formats TCS ...TCS画面 452.5.3.1 Screen format TCS RDY ...TCS准备画面 452.5.3.2 Screen format HGC/EGC ... HGC/EGC画面 452.5.3.3 Screen format WRB ...工作辊弯辊画面 452.5.3.4 Screen format HWC/EEGC ... HWC/EEGC画面 452.5.4 Screen formats auxiliaries 辅助系统画面 462.5.4.1 Screen format hydraulic aux液压辅助系统画面 462.5.4.2 Screen format hydraulic servo液压伺服系统画面 482.5.4.3 Screen format gear oil稀油润滑画面 492.5.4.4 Screen format oil film润滑系统画面 502.5.4.5 Screen format main drive lubrication主电机润滑画面 512.5.4.6 Screen format water水系统画面 522.5.4.7 Screen format utilities有效画面 532.5.4.8 Main drive auxiliaries主传动辅助系统 542.5.4.9 Main drive alarms主传动报警 552.5.5 Common screen formats公共画面 562.5.5.1 Screen format E-Stop紧停画面 572.5.5.2 Screen format alarm list报警清单画面 582.5.5.3 Screen format event list事件清单画面 592.5.5.4 Screen format maintenance维修画面 606 Operator devices 设备操作 612.6.1 Operator devices on main control desk +20S4.P01(VAI Linz)主控制台设备操作 61 2.6.2 Operator devices on local control posts就地面板操作 662.7 Production生产过程 872.7.1 Selection of modes选择模式 872.7.2 Local Mode就地模式 902.7.2.1 Local mode hydraulic system液压系统就地模式 902.7.2.2 Local mode lubrication system润滑系统就地模式 922.7.2.3 Local mode plate mill roll change轧机换辊就地模式 952.7.2.4 Local mode plate edger roll change立轧换辊就地模式 982.7.2.5 Local mode primary descaler粗除鳞就地模式 992.7.3 Manual mode手动模式 1012.7.3.1 Roller tables辊道 1012.7.3.2 Roller table oscillation摆动辊道 1042.7.3.3 Turn tables回转辊道 1062.7.3.4 Side guides侧导板 1072.7.3.5 Descalers粗除鳞箱 1082.7.3.6 Screw down ...轧机压下 1092.7.3.7 Screw in ...立轧侧压 1092.7.3.8 HAWC (109)2.7.3.9 HAGC (109)2.7.3.10 Work roll bending ...工作辊弯辊 1092.7.4 Automatic mode 自动模式 1102.7.4.1 Roller tables 辊道 1102.7.4.2 Roller table oscillation 摆动辊道 1122.7.4.3 Turn tables回转辊道 1132.7.4.4 Side guides侧导板 1142.7.4.5 Descalers粗除鳞 1152.7.4.6 Screw down .. 轧机压下. 1162.7.4.7 Screw in ... 立轧侧压 1162.7.4.8 HAWC (116)2.7.4.9 HAGC (116)2.7.4.10 Work roll bending ...工作辊弯辊 1162.8 Roll change ...换辊 1172.8.1 Roll change mill stand 主轧机换辊 1172.8.1.1 Local operation 就地模式 1172.8.1.2 (Semi-)automatic roll change半自动换辊模式 1202.8.1.3 Work roll change procedure工作辊换辊程序 1212.8.1.4 Back up roll change procedure支撑辊换辊程序 1282.8.2 Roll change edger ...立轧机换辊 1312.9 Superimposed functions (132)2.9.1 Speed generation 速度概述 1332.9.2 Quick stop function 快停功能 1342.9.3 Actions after a quick stop 快停后的实际状态 1352.9.4 Status of plate mill system轧机系统状态 1362.9.5 Text indication on overview display 指令文本显示 1372.9.6 Functions for equipment protection ...设备保护功能 1382.10 Calibration ...标定（校对） 1382.10.1 Calibration mill stand ..主.轧机标定 1382.10.2 Calibration edger ...立轧机标定 1382.10.3 Calibration side guides侧导板标定 1392.11 Test control and activities at certain intervals测试控制和区域跟踪 140 2.12 Troubles and trouble shooting ...问题提示 1412.12.1 Electric and automation system电气和自动系统 141Heating area:加热区Furnace 加热炉Gas 煤气Mixed gas 混合煤气Nitrogen 氮气Oxygen 氧气Resident oxygen 炉内残氧Pressure 压力Volume 体积、流量Valve 阀门Slab 板坯Slab yard 板坯库Continuous cast slab 连铸板坯Width 宽度Thickness 厚度Length 长度Weight 重量Bend 弯曲Combust 燃烧Temperature 温度Centigrade degree 摄氏度Pyrometer 高温计Thermocouples 热电偶Fixed beam 固定梁Walking beam 步进梁Forward 向前Backward 向后Discard 剔除Discard table 剔除辊道Charge 装炉Discharge 出炉Preheating zone 预热区Heating zone 加热区Soaking zone 均热区Vaporizing cooling/ vapour cooling 气化冷却Soft water 软水Scale 氧化铁皮Ventilate 通风Chimney 烟囱Exhaust 废气Stack 烟道Roller table 辊道Baffle 挡板Charge machine 装钢机Discharge machine 出钢机Compressed air 压缩空气Burner 烧嘴Combustion air fan 助燃风机Recuperative heat exchanger回热式热交换器Refractory brick 耐火砖Mathematic model 数学模型Feed-forward 前馈Feedback 后馈/反馈Furnace pressure 炉压Temperature profile 温度曲线Hot rolling shop：热轧车间Mill 轧机4-high finishing mill 四辊精轧机Rough mill 粗轧Screw down 压下Screw up 抬升辊缝Edger 立辊轧机，轧边机High-pressure descaling system 高压水除鳞系统Nozzle 喷嘴Heat cover 保温罩Shear 剪机Hydraulic loop液压活套Looper 活套辊Side guide 侧导卫Interstand cooling 机架间冷却Run-out table 精轧输出辊道Laminar cooling 层流冷却Head water tunk 高位水箱Side stripper 侧喷头Pinch roll 夹送辊Down Coiler 卷取机Mandrel 卷取机芯轴Wrapper roller 助卷辊Coil stripper car 卸卷小车Strip catcher 卷取区域带钢拦截装置Gear motor 齿轮马达Coupling 接手，连接器Spindle 接轴Universal Spindle 万向接轴Shaft 轴Roll changing device 换辊装置Crane 行车Bite 咬入Cascade speed adjustment 节联调速Cobble 堆钢事故，中间事故坯料Tension 张力Tension control 张力控制Loop height 活套量/活套高度Speed up 升速Lock cylinder 锁紧缸Balance cylinder 平衡缸Lift 提升Shift 横移Leveling 校平，调平Zero 校零Alignment 对中Industrial water 循环水Water volume 水量Water pressure 水压Cooling rate 冷却速度Speed cone 速度锥Maintenance 检修，维护Pneumatic system 气动系统Roll shop 轧辊间Roll 轧辊Grinder 磨床Work roll grinder 工作辊磨床Combinative/universal grinder 组合磨床Work roll 工作辊Back-up roll 支撑辊Barrel 辊身Roll neck 辊颈Roll cooling 轧辊冷却Work roll chock 工作辊轴承座Work roll bending system 工作辊弯辊系统Work roll shifting system 工作辊窜辊系统Back-up roll chock 支撑辊轴承座Bearing 轴承Work roll bearing 工作辊轴承Oil film bearing/morgoil bearing 油膜轴承Headstock 头架T ailstock 尾架Grinding carriage 磨头滑架Wheel 砂轮Dressing diamond 修整金刚石Measure 测量Size 尺寸Diameter 直径Ovality 不圆度Roundness 圆度Eccentricity 偏心度Contour 外形轮廓Geometry 几何尺寸，几何形状Curve 曲线Sine curve 正玄曲线Active curve 实际曲线Rated curve 额定曲线/设定的曲线Position 位置Axis 轴，数轴Horizontal 水平的Vertical 垂直的Calibration 校准，刻度Compensation 补偿Correction 纠正Control panel 控制面板，操作控制台Deviation 偏差Error 误差，错误Offset 偏差量Definition 定义Reverse 反转Swivel 回转，转动Distance 距离Range 范围Chamfer 凸度Centerline 中心线Infeed mode 进给模式Limit 限制，极限Limit switch 限位开关Scan 扫描Coolant 冷却剂Surface 表面Plunge grinding 掏沟磨削Caliper 测量卡规Optimize 优化Load roll 装辊Unload roll 卸辊Calibrate caliper 校准测量卡规Finishing area 精整区域Coil marking machine 钢卷标号机Coil strapping machine 钢卷打捆机Coil weighing device 钢卷称重装置Sampling shear 取样剪Transfer chain 链条运输机Walking beam transfer 步进梁运输机Coil yard 钢卷库Skin pass 平整机Saddle 鞍座Electric room 电气室Motor 电机Main motor 主电机Load 载荷Over load 过载Motor load 电机负荷Rolling force 轧制力Rolling speed 轧制速度MPM: meter per minute 米/分钟Torque 扭矩Rated torque 额定扭矩Voltage 电压Process computer 过程计算机Program 程序，编程PLC：programmable logic controller 可编程控制器Encoder 编码器Information 信息Ghost rolling 模拟轧制Measuring instrument 测量仪表X-ray X射线Thickness gauge 测厚仪Width gauge 测宽仪HMD: hot material detector 热金属探测仪CMD: cold material detector 冷金属探测仪Light barrier 光栅Automatic model 自动模式Semi-auto model 半自动模式Manual model 手动模式Emergency 紧急，急停Joggle 点动HMI：human machine interface 人机界面AC frequency converter 交流变频器I/O：input/output 输入/输出端口Step control 卷取机助卷辊的“踏步”控制Hydraulic system 液压系统Grease 甘油Oil 油，稀油Oil station 油站SSC: Short stroke control 短行程控制AGC: automatic gauge control 自动压下控制AWC: automatic width control 自动宽度控制Pump 泵Screw pump 螺杆泵Filter 过滤器，滤网Cylinder 液压缸，圆柱体Valve stand 阀台Accumulator 蓄能器Leakage 泄漏Product 产品Grade 钢种Batch 一炉，一批Batch No. 炉批号Coil 钢卷Strip 带钢，薄带钢Sheet 钢板，薄钢板Plate 中厚板Physical performance 物理性能Mechanical performance 机械性能Strength 强度Elongation 延伸Flatness 平直度Plasticity 塑性Crown amber 凸度Hardness 硬度Microstructure 微观组织结构Austenite 奥氏体Ferrite 铁素体Pearlite 珠光体Deep drawn 深冲SPHC 普通级热轧钢板（卷）SPHD 深冲级热轧钢板（卷）SPCC 普通级冷轧钢板（卷）SPCD 深冲级冷轧钢板（卷）High strength low-alloy steel 低合金高强度钢Silicon steel 硅钢，电工钢Galvanizing 镀锌Coating 涂镀，涂层Heat treatment 热处理Aging 时效处理Annealing 退火Quenching 淬火Other Alarm 报警Anchoring bolt 地脚螺栓Yield 产量，成材率Ton 吨Annual 一年的Month 月Day 日Shift 班Safety 安全Radioactive hazard 放射性伤害Caution 注意，小心Layout 平面布置Document 文件Documentation 技术文本，技术文件报价书TOP: take-over point 交接点High-alhali cement 高硷水泥High-alumina brick 高铝砖High-alumina cement 高铝水泥High-alumina refractory 高铝耐火材料High-angle boundary 高角晶界High-conductivity berllium copper 高导电铍铜合金high-duty fireclay brick 高级火黏土砖High-early streagth Potland cement 早强波德兰水泥high-early-strength cement 早强水泥High-energy-rate forming 高能率成形high-frequency heating 高频加热法High-frequency induction furnace 高周波感应电炉High-frequency induction hardening 高周波硬化high-frequency induction heating method 高频感应加热法High-frequency welding 高周波熔接high-leaeded brass 高铅黄铜High-manganese steel 高锰钢High-phosphorous pig [iron] 高磷生铁High-silicon bronze 高矽青铜High-silicon cast iron 高矽铸铁High-speed steel 高速钢High-temperature alloy 耐高温合金High-temperature carburizing 高温渗碳High-temperature corrosion 高温腐蚀High-temperature oxidation 高温氧化High-temperature refractory 高温耐火材料High-temsile steel 高强度钢High-tension steel 高强度钢High-velocity forging 高速锻造high-velocity thermocouple 高速热电偶high-zinc brass 高锌黄铜Hindered contraction 限缩变形Hiperco 海派钴(高导磁铁钴铬合金)Hipernick 海派镍(高导磁率合金50%Fe,50%Ni) histogram memory 条带图记忆器hit rate 击中率Hoffmann kiln 何夫曼窑Hogging 切整(用焰切法)Holding furnace 保温炉Hole 孔Holfos bronze 难弗青铜(今10%-23%Sn 之青铜)hollow billet 中空钢胚hollow block 空心砖hollow casting 空铸法hollow clay block 空心黏土砖Hollow-brick 空心砖hollow-ware 深皿Holmium (ho,67)金火Holocrystalline 全结晶质hologram 全像片Holography 全像摄影Homogeneity 均质Homogeneous carburizing 均质渗碳Homogeneous deformation 均匀变形Homogeneous material 均质材料Homogeneous nucleation 均态成核Homogeneous structure 均质组织Homogenization 均质化，均质作用Homogenizing 均质化Homogenizing anneal 均质化退火Homopolar bonding 同极结合Honda alloy 本田合金(永久磁体，15-35%Co,10-25%Ni,8-25%Ti 其余为Fe) hone 搪磨石Honing 搪磨hood 通风橱；排气罩Hook gauge 钩式度量尺，钩尺Hook's law 虎克定律Hookean solid 虎克固体Hoop iron 箍铁Hopkins process 霍普金法Hopper 漏斗horizontal Bridgman method 水平型布里志曼法horizontal loader 树脂接合Horizontal press 帮式压机Horn press 角台压机horse 梯桁；鞍形支架Horse power 马力Horseshoe magnet 马蹄铁形磁体hot acid circulation and filtration system 高温酸液循环过滤系统Hot air stove 热风炉hot air (gas)drying equipment 热空气乾燥设备Hot bent test 热变试验hot blast cupola 热风焙铁炉hot blast furnace 热风炉Hot casting crack 热铸裂Hot cathod ionization gauge 热阴极游离[真空]计Hot cell 辐射室hot chuck 高温夹具Hot coining 热压印Hot cold work 热冷加工Hot cracking 热裂Hot deformation 热变形Hot dipping 热浸法Hot drawing 热拉法Hot extrusion 热挤hot floor 热炕Hot forging 热锻造Hot forming 热成形Hot hardness 高温硬度Hot heading 热锻粗Hot hubbing 热模压Hot junction 热接端Hot laboratory (hot lab)热实验室(放射性材料实验室) Hot peening 热珠击法Hot peening marquenching 热珠击麻淬火Hot permeability 热通气性hot plate oven 热平板烘烤炉Hot pressing 热压制hot rolled bar steel 热轧钢条Hot rolled sheet steel 热轧钢片Hot rolling 热轧Hot sawing 热锯切Hot shearing 热剪裁hot shortness 热脆性Hot sizing 热修准Hot stage 热载台(显微镜用)Hot stage microscope 高温载台显微镜Hot stretching 热伸展Hot tear 热裂Hot tinting 热着色法Hot top 热顶Hot trimming 热修边Hot upsetting 热锻粗hot wall 热壁Hot wall furnace 热壁炉Hot work 热加工，热作，高温加工Hot working die steel 热[作]模钢hot zone parts 加热区域组件hot-blast stove 热风炉hot-carrier test 热载子试验Hot-dip metallic coating 热浸金属护膜hot-metal ladle 熔金属盛桶hot-metal mixer 熔铁混合器hot-patching 热补法hot-plate spalling test 热板剥落试验Hot-strip mill 板条热轧机Hot-wire process 热丝精炼法hot0blast main 热风主道hotel china 旅馆用瓷；厚质餐瓷Hotfeld time-yield test 哈特菲时间对降代潜变试验Hounsfield tensometer 韩司菲尔张力计Hour-glass fracture 沙漏形破裂Hovel kiln 贺非窑；罩窑Hover kiln 气垫隧道窑Hoyt No.11 赫意德十一号合金(轴承金属2.5%Cu,7%Sb 其余为锡) hub blade 毂状磨石刀片Hubbing 轮毂成形，阴模攻制Huber's alloy 胡伯合金(85%Ce, 其余为铁之一种打火合金)hubless blade 无中枢刀片Huggenberger tensometer 胡根伯格伸长计Hume-Rothery phase 休木若塞瑞相humidity dryer 调湿乾燥室Humman body corrosion 人体腐蚀Humphrey's reagent 韩福瑞试剂Humphreys spiral concentrator 韩福瑞蜗旋机Huntington-Heberleim sink and float 亨汀顿海布林浮沉法Hy-tuf steel 强勒钢(典型成分为0.25%C,1.2%Mn,1.5%Si,1.8%Ni,0.4%Mo)hybrid scan 混合式扫描Hydra steels 海着钢(类似热模钢)Hydrated alumina 水化铝氧Hydrated lime 消石灰Hydration 水合[作用]hydraulic blade tensioning 油压式张力刀片Hydraulic cement 水硬性水泥Hydraulic forming 液压成形Hydraulic lime 水硬石灰hydraulic press 液压机hydraulic setting refractory 水凝[性]耐火物Hydraulic sizer 水力筛分机hydraulicking 水掘法Hydrazine 联胺(无色液体N2H4，为一强还原剂)Hydride 氢化物Hydride descaling 氢化物去锈法hydro-blast 高压水清砂机Hydrochloric acid 盐酸Hydrocyclone classifier 湿式旋涡分级机hydrofluoric acid hydrogen peroxide mixture cleaning solution 氢氟酸过氧化氢混合洗涤液hydrogen blistering 氢泡伤Hydrogen damage (hydrogen attack)氢害Hydrogen electrode 氢电极hydrogen embrittlement 氢脆性，氢脆化Hydrogen film 氢膜hydrogen gas burning 氢气燃烧Hydrogen loss 氢内损常(p/m)Hydrogen overvoltage 氢过[电]压hydrogen termination 氢终结化hydrogen-treating process 氢处理法(搪瓷)Hydrometallurgy 水冶金，湿法冶金hydrometer[ 液体]比重计Hydronalium 海装铝(含2-10%Mg, 0.2-1.5%Si,0.2-1.0%Mu 的一系列铝合金) hydropgen annealed wafer 经氢气退火之晶圆Hydrophilic colloid 亲水胶体Hydrophobic colloid 疏水胶体Hydroseparator 水力分离器Hydrosol 水溶胶Hydrostatic extrusion 静力液挤压Hydrostatic pressing 液均压法(粉未冶金)Hydrostatic tension 均张力Hydryzing 氢流热处理hygrometer 湿度计Hypereutectic 过共晶Hypereutectic alloy 过共晶合金Hypereutectic cast iron 过共晶铸铁Hypereutectoid alloy 过共析合金Hypereutectoid cast iron 过共析铸铁Hypereutectoid steel 过共析钢Hypocrystalline 亚结得质Hypoeutectic 亚共晶Hypoeutectic cast iron 亚共晶铸铁Hypoeutective alloy 亚共晶合金Hypoeutectoid steel 亚共析钢Hysteresis loop 磁滞环hystersis 迟滞hystersis loss 迟滞损失i-line stepperi 线步进机i-type semiconductorｉ型半导体I/O switching transitionI/O 介面转换时间ice cleaning equipment 冰粒洗涤机ice jet cleaning equipment 冰粒喷射涤装置ID mark 辨识标记IDD quiescent test 等待电流静态测试ignition arch 点火拱illite 伊莱石(从矿)illumination intensity at image plane 影像面照度强度illumination system 照明系统illumination uniformity error 照度均一误差ilmenite 钛铁矿image data memory 影像数据记忆器image data processing 影像数据处理image data processor 影像数据处理器image field 影像图场image processor unit 影像处理器单元imbibition 吸液膨胀immersion wet etching system 浸渍式蚀刻系统impact mill 冲击机impact resistance 冲击抗力impervious 不渗透implant chamber 离子植入式impregnated-carbon silicon carbide 碳渍碳化矽impurity level 杂质能阶impurity trap 杂质陷阱in circuit emulater 插入电路模拟版in-glaze decoration 釉内彩[饰]in-situ 就地，在现场，自然(环境)incising 雕饰incongruent melting 分熔indentation 压痕indenting 缺口index amount 指数量indexer 指标器，索引器indexing 指数标定；转位indirect-arc furnace 间接电弧炉individual wafer retrieval 晶圆片个别取出induction furnace 感应电炉induction heating 感应加热[法]induction heating evaporation system 感应加热蒸镀系统inductive coupled plasma enhanced CVD system 电感性耦合等离子体增强型CVD 系统inductively coupled plasma etching system 感应耦合型等离子体蚀刻系统infeed grinding 输送中研磨infra-red drying 红外线乾燥[法]infrared absorption spectroscopy 红外线吸收光谱学infrared annealer 外线退火处理机infrared heating method 红外线聚集加热法infrared laser scattering tomograph 红外光雷射散射断层X 光摄影装置infusorial earth 矽藻土ingot 晶锭ingot cutting face bow 晶锭切断面弯曲ingot end face measuring system 晶锭端面弯曲测式系统initial set 初凝injection moulding 射入模制injection pressure 注入压力injection speed 注入速度injector 注入器ink jet printer 喷墨式印刷机inker 印字机inlaying 镶嵌inline heater 管线上加热器inline system 线上系统，插列系统inner diameter blade 内径刀片inner diameter saw 内径锯子inner diameter saw with built-in grinder 内径锯子研磨机inner lead 内部引线inner lead bonder 内部引线接合机inner lead bonding 内部引线接合inorganic pigment 无机颜料input 输入图案：预期图案input pattern stimulus 输入图案信号资料群input slew rate 输入变化率input/output buffer information 出入/输出缓冲器资讯规格insert ring 插入环inserter remover 插入拔除机inside heating method 内部加热法inspection of dust particle on wafer 晶圆表面灰尘检查instrumentation rack 仪器架insufflation 喷灰入窑insulating refractory 绝热耐火物intaglio 凹雕(玻)intellectual property 智慧财产权inter leaf loader 隔片装载机interface between solid and melt 固液体界面interface unit 介面单元interlocking tile 互扣瓦intermediate crusher 中级轧碎机periodic kiln internal die pressure 模内压力internal gear 内部齿轮internal gettering 内部吸器internal torch unit 内部火炬装置interstitial oxygen 晶格间氧气，格隙氧气interstitial siteintrinsic gettering 本徵吸器intrinsic semiconductor 本徵半导体intumescenc 胀大inversion 转化inverted pyramidal collet 颠倒金字塔型吸具investment casting ion beam 离子束ion beam etching system 离子束蚀刻系统ion beam lithography 离子束微影术ion beam sputtering system 离子束溅镀系统ion current 离子电流ion energy 离子能量ion exchange membrane 离子交换膜ion implantation 离子值入，离子移植ion implanter 离子注入机ion micro probe (mass)analysis method 离子微探针质谱仪分析法ion micro probe（mass）analysis method 离子微探针质谱仪分析法ion milling system 离子铣削系统ion plating system 离子喷镀系统ion source 离子源ion source magnet 离子源磁铁ionic bonding ionic exchange 离子交换ionized cluster beam evaporation system 成团离子线束蒸镀系统IPA vapor drying 异丙醇(IPA)蒸汽乾燥IR dropIR 电压降IR oven 红外线烘烤炉irising 生晕(玻)iron modulus 铁模数(泥)iron notch 出铁口iron spot 铁斑iron-zirconium pink 铁钴红ironstone china 硬质陶器isomer 异构物isostatic pressing 均压法；等压压制isotropic etching 各向同性蚀刻，等向性蚀刻Italian tiles 义大利式面砖jack arch 平拱jamb wall 侧墙jamming 接收干扰jamming rate 干扰率jar mill 瓶磨jasper ware 贾士巴陶石器jaw crusher 颚[式轧]碎机jena glass 耶那玻璃jet dryer 喷射乾燥器jeweller's enamel 质饰珐琅jiggerjiggering jiggerman 旋坯工；拉坯工(玻)joint line 接缝joint test action group 联合测试推动团体jolleyjolt moulding 震捣模制[法]Jominy end quench test jump function 跳越功能just etching 适量蚀刻kaolin 高岭土kaolinite 高岭石kaolinization 高岭土化[作用]Cassel kiln Keene's cement, Keene's plaster 克恩水泥Kelly ball test 克里球试验(泥)Kelly sedimentation tube 克里沉积管Kelvin contact 开耳芬接点Kelvin temperature scale 克耳文温标(从化工)kerf inspection 劈痕检查kerf loss 截口损失kerf thickness 刀刃（截口）厚度Key brick 键砖kibushi-clay 木节土kieselguhr 矽藻土kiln basin 料浆池kiln bedding 窑料层kiln car 窑车kiln crown 窑顶kiln floor 窑床kiln foundation 窑基kiln furniture 窑具kiln lining 窑衬kiln pier 窑台kiln quadrant 窑象限kiln shell 窑壳kinematic coupling 运动学上之耦合Klein turbidimeter 凯林浊度计Knocking 膏震(泥)knockings 滤渣(陶)Knoop hardness test knot 节(波)known good die 已知合格之晶片Knudsen cell 克努森容器Kohn pipette 丘氏吸管Kuhl cement 库耳水泥kyanite 蓝晶石lacustrine clay 湖积[黏]土Ladd circular tunnel kiln 雷氏圆形隧道窑ladder 支架(玻)ladle 熔桶(陶)；长柄勺(玻)ladle brick 熔液盛桶砖laitance 渗出物(泥)laminate 叠片laminated glass 层合玻璃lamination 层状组织(陶)lamp arrangement 灯泡排列lamp base cement 灯泡黏合剂lamp power control 照射灯功率控制lamp-blown 喷灯吹制(玻)lancing 清除lap 摺痕(玻)lapped wafer 经磨光晶圆lapping lapping wafer 刚磨光晶圆larnite 矽灰石laser laser ablation 雷射烧蚀laser annealer 雷射退火处理机laser assisted CVD system 雷射辅助型CVD 系统laser beam prober 雷射光束探测器laser beam test system 雷射光束测试系统laser beam welding equipment 雷射光束焊接装置laser bonding 雷射接合laser cavity 苗射谐振腔laser doping system 雷射掺杂系统laser homogenizer 雷射波束均匀化机laser mark 雷射标记laser marker 雷射标印机laser microscope 雷射显微镜laser output stability 雷射输出稳定度laser power 雷射功率laser processing system 雷射处理系统laser scattering tomograph defect 雷射散射X 光断层摄影缺陷laser soldering laser surface scanner 晶圆表面雷射扫描器lathe 车床lattice brick 格子砖lattice constant 晶体常数；点阵常数lander layout driven synthesis 布置驱动合成layout editor 配置编辑器layout parameter extraction 配置参数萃取layout versus schematic 配置、检图对照layout-circuit comparison 配置电路比较leachinglead coplanarity 脚端同平面性lead cutting/lead trimming 脚端切断/脚端修剪lead forming 脚端整形，脚端弯曲lead frame 引导框架，花架lead frame loader 引导框架装载机lead glaze 铅釉lead locater 引线定位器lead on chip 脚端由晶片引线端焊接之封装体lead poisoning 铅毒；中铅毒lead solubility test 铅溶度试睑leadless glaze 无铅釉leaf type contract 薄板型接触lean clay 贫黏土leather-hard 半乾lehr 徐冷窑length of fresh wire feeding 新线馈线长度lens projection aligner 透镜投影对准曝光器lens-fronted tubing 凸面玻管lepidolite 鳞云母Lessing rings 勒辛陶圈leucite 白榴子石license 许可证、执照life time 寿命lifetime measurement system（载子）寿命测试系统light 低折射率[光学]玻璃light figure method 光像法light integrator 光线积分器light metal light scattering measurement system 光散射测量系统light scattering measurement system (LSM)光散射测量系统light scattering method 光散射法。

轧钢专业词汇

(1) 烧结Sintering抽风机drawing fan, exhausting fan除尘集灰斗dust hopper除尘设备dedusting equipment带式焙烧机travelling grate ( induration ) machine 带式烧结机continuous-strand sinter machine点火器igniter垫底料给料机bedding burden feeder多管除尘器multi-type deduster二次混料机secondary mixing machine返矿仓return ore bunker废品率reject rate粉矿fines富矿rich ore鼓风机blower含铁品位grade of iron合格率percent of pass合格烧结矿qualified sinter回转窑rotary kiln混合料仓mixing bunker混合料给料机mixed burden feeder碱度basicity焦末nut coke, coke breeze精矿粉concentrate fines链蓖机grate, chain-type grate炉尘dust盘式烧结机batch-type sinter machine破碎机breaker球团pellet球团矿pellet燃料fuel material燃烧器burner熔剂flux筛分设备screening equipment烧结sintering烧结车间sintering plant烧结矿sinter烧结矿返矿率sinter return ratio烧结矿品位grade of sinter生球fresh ( green ) pellet石灰石limestone熟料clinker竖炉shaft furnace台车pallet无烟煤anthracite, anthracitic coal压块briquette氧化铁皮scale萤石fluorite圆盘给料机disk-type feeder圆盘造球机disc-type pelletizing machine 圆筒造球机cylinderical pelletizer造球机pelletizer, pelletizing machine转鼓指数drum index自熔性烧结矿self-fluxing sinter作业率operability(2) 焦化及耐火Coking and refractory氨ammonia氨工段ammonia plant耙焦机coke-drawing machine白云石dolomite白云石砖dolomite brick苯benzole肥煤fat coal, bituminous coal副产品by product干熄煤机dry quenching machine 高铝砖alumina brick铬镁砖chromo-magnesite brick 铬砖chromite brick硅石silica灰粉ash content挥发物volatiles, volatimeter焦化厂coking plant焦炉coke oven焦炉煤气coke oven gas焦煤coking coal焦炭转鼓试验coke drum test焦油tar抗渣性slag resistance炼焦coking炼焦炉组coke oven buttery晾焦台wharf炉门框door frame铝镁砖aluminium镁石magnesite镁砖magnesia brick磨煤机coal pulverizer耐火材料refractory material耐火度refractoriness耐火粘土refractory clay, fire clay配煤mixing coal平煤机coal levelling machine启炉门机door-extracting machine气孔率porosity气煤gas coal, bottle coal轻质膨胀粘土骨料light weight expanded clay aggregate 燃烧室combustion chamber瘦煤carbonaceous coal碳砖carbon brick炭化室(炉孔) co oven推焦杆pushing ram脱苯塔benzole scrubber熄焦机coke quenching machine洗氨塔ammonia scrubber洗氨塔ammonia washer洗煤washed coal洗萘塔naphthalene scrubber烟煤bituminous coal, bituminite粘土砖chamotte brick装煤孔coal charging hole(3)炼铁Ironmaking白云石dolomite崩料,坐料slipping布料器distributor称量车weighing car出铁场casting house出铁沟tapping channel出铁口iron notch, taphole出铁口喷火blowing on taphole出渣沟slagging channel吹慢风slack-wind blowing磁铁矿magnetite大料钟large bell低品位矿石low grade ore电动泥炮motor operated mud gun电子秤electronic weigher吊挂保护板hanging protective plate 堵铁口机taphole stopping machine放灰阀dust discharging valve废气总管waste gas main duct风口tuyere风口大套tuyere-cooler casing风口管blast pipe风口镜tuyere glass风口弯管penstock damper风量blast volume风量控制器blast volume controller风速blast velocity富矿rich ore, premiun ore高炉blast furnace高炉鼓风机blast furnace blower高炉骨架frame of furnace高炉利用系数utilization coefficient高炉煤气BF gas高炉外壳shell of furnace高品位烧结矿high grade sintered ore高压炉顶high pressure on top格砖checker brick鼓风机站blower station褐铁矿brown iron ore换热式热风炉intermittent stove荒煤气crude gas黄铁矿, 赤铁矿hematite混风阀mixed air valve计划休风scheduled down-time焦比coke ratio焦炭coke紧急休风emergency blowing-down 静电除尘器electrostatic precipitator 卷扬机室hoist room均压阀equalizer valve开铁口机tapper, tapping machine 块矿briquette块矿lump ore矿槽bunker矿粉fine ore冷风阀cold blast valve冷风阀cooled blast valve冷风总管cooled blast main duct冷却水箱cooling water box立式冷却壁cooling stave料车skip料车skip car料线,料面高度stockline料钟bell料柱stock column硫酸渣purple ore炉衬linings炉底bottom炉顶top炉顶卷扬机top hoist炉顶平台top platform炉顶温度top temperature炉顶压力top pressure炉腹bosh炉缸hearth炉缸压力hearth pressure炉喉(护)板stock line armor炉喉throat炉况不顺blast wandering炉前工, 高炉工人blast furnace operator 炉身stack炉身冷却壁stock cooling plate炉腰waist, straight section螺旋推进式泥炮spiral type clay gun慢风slow-wind blowing煤气调节阀gas regulating valve煤气阀gas valve煤气放散阀bleeder valve煤气换向阀gas reversing valve煤气净化gas cleaning (purifying)煤气总管main gas duct泥炮mud ( clay ) gun泥炮mud, clay皮带秤belt scale皮带运输机belt conveyer撇渣器skimmer贫矿lean, low grade ore砌体brickwork气缸式泥炮cylinder type clay gun切断闸板cut-off damper球团矿pellet燃烧器burner燃烧室combustion chamber热风阀hot blast valve热风阀hot blast valve热风炉stove热风炉交叉并联透风staggered parallel blowing 热风围管hot blast circular duct热风温度hot blast temperature热风总管hot blast main duct熔剂flux上升管uptake duct烧结矿sinter石灰石lime stone水冲渣granulation双料钟double bell死铁层old horse探尺,料尺stock rod探尺卷扬机stock rod winch铁精矿concentrate铁矿石iron ore铁水罐hot metal ladle铁水罐车hot metal ladle car铁渣比iron and slag ratio透风期on blast透平发电机turbo-generator透平鼓风机turbo-blower外燃式热风炉external combustion type stove 外燃室external combustion chamber文氏管洗涤器venturi scrubber无料钟炉顶bell-less top下降管downcomer duct小料钟small bell斜桥skip bridge, hoist bridge休风blowing-down休风率downtime percentage蓄热式热风炉,考伯式热风炉cowper stove蓄热室checker chamber旋风除尘器cyclone旋转布料器rotary burden distributor烟道阀duct damper移动保护板movable protective plate有效利用系数productivity coefficient有效面积effective volume鱼雷式铁水罐torpedo ladle鱼雷式铁水罐车torpedo ladle car造渣slag-making造渣厂富氧鼓风oxygen-enriched blast造渣填加剂slag-making addition渣场slag yard渣罐slag pot, slag ladle渣罐车slag pot car渣罐车备用停车线slag tapping stand-by track 渣坑slag pocket, slag pit渣口, 出渣口slag notch渣口slag notch, cinder notch渣口大套slag notch cooler渣口喷火blowing on the monkey渣口水箱monkey jacket渣口小套, 小渣口monkey渣口小套slag (notch) tuyere渣盘slag pan整粒矿石sized ore重力除尘器gravity dust collector主沟main channel柱塞式泥炮plunger type clay gun铸铁机pig moulding machine铸铁块, 锭pig ingot装料漏斗charging hopper自熔性矿石self-fluxing ore(4)炼钢Steelmaking奥式体钢austenitic steel八角钢材octagon bar白云石dolomite板坯连铸机slab casting machine半封闭型电炉semi-closed type EAF保护渣slag powder补炉机fettling machine不锈钢stainless steel敞开固定型电炉open stationary type EAF敞开回转型电炉open rotating type EAF敞开斜动型电炉open tilting type EAF超低头方坯连铸机extra low head caster(ELH)for bloom, super low head caster ( SLH )超高功率电炉UHP electrical furnace车屑chip车铸bogie (buggy,car) casting称量weighing出钢tapping出铁盘tapping pan出渣slagging除渣器deslagger储槽storage bunker吹氧转炉basic oxygen furnace打印机stamping machine大密封罩, 狗窝dog house带卷strip coil带型连铸机belt type CCM单炉浇铸batch cast捣固料ramming compound捣糊pound to paste捣炉机stoking machine底吹氧气转炉bottom bloom oxygen converter底注, 下注uphill casting, uphill teeming底电极bottom electrode地下料仓underground bunker电极electrode电极压放slip, slipping电极接长系统electrode jointing system电极把持器electrode holder电极柱electrode mast电极糊electrode paste电极套壳electrode casing电极压放装置electrode slipping device电炉electrical arc-furnace (EAF)电炉钢electric arc furnace (EAF) steel顶吹氧气转炉top bloom oxygen converter顶底复合吹转炉top and bottom com bined blown converter多流连铸机multi-strand CCM多炉连铸continuous continuous casting二次精炼secondary refining矾土, 氧化铝alumina方坯连铸机billet cast machine非铁合金non ferro-alloy废钢scrap废钢跨scrap bay废铁iron scrap沸腾钢unkilled steel分类料仓classification bin封闭固定型电炉closed stationary type EAF封闭回转型电炉closed rotating type EAF付枪, 付氧枪sublance负偏差negative deviation富氧鼓风oxygen-enriched blowing钢包, 盛钢桶ladle钢包加热炉ladle heating furnace钢包旋转台turret, ladle turnable钢锭ingot钢锭模ingot mould钢筋reinforcing bar, rebar钢坯清理间billet conditioning yard钢种kinds of steel高位料仓overhead bunker高压炉顶high pressure top铬铁ferro-chromium给料feeding工具钢tool steel工业纯铁armco-iron鼓肚bulging固定碳fix carbon content硅锰合金silicon manganese alloy硅铁ferro-silicon合金钢alloy steel化学成份chemical composition弧型连铸机bow type CCM滑动水口slide gate还原剂reductant还原剂reduction agent, reductant灰份ash挥发物volatile混料mixed material混铁炉mixer火焰切割机torch cutting machine火焰清理flame deseaming, hot scarfing 夹杂物impurity加料管charging chute碱性渣basic slag结构钢structural steel结晶器mould, crystalliser焦比specific coke rate焦炭coke交流电弧炉AC electrical arc furnace浇铸吊车casting crane浇铸机casting machine浇铸坑casting pit浇铸平台casting platform浇铸周期casting cycle浇注casting浇注teeming浇注底板pouring bottom plate金属硅silicon metal浸入式水口submerged nozzle开浇cast-on开铁口机open hole machine可浇注性castability可逆皮带运输机reverse belt conveyer坑铸pit-casting孔型设计groove design矿石mineral拉矫机straightening and withdrawalmachine拉坯机withdrawal device冷轧带卷cold-rolled coil冷轧钢cold-rolled steel立弯型连铸机vertical type CCM, straight mouldbent run-out plant粒度grain size连铸continuous casting连铸机continuous casting machine- CCM 溜槽,溜管chute硫印sulphur print六角钢材hexahedral bar炉壁结瘤wall accretion炉衬furnace lining炉顶料仓top bin炉盖furnace cover炉缸结瘤hearth accretion炉龄campaign炉体furnace body炉子跨furnace bay漏钢breakout铝块aluminium block马式体钢Martensitic steel埋弧电炉submerged electric furnace煤粉pulverized coal锰铁ferro-manganese磨煤机coal pulverizer模铸mold casting木材timber木片wood chip镍铁ferro-nickel喷煤coal injection偏差deviation平炉open hearth furnace(OHF)平炉钢open hearth furnace (OHF) steel 破碎crush全连铸sequence casting热轧带卷hot-rolled coil热轧钢hot-rolled steel熔剂flux塞棒stopper rod筛分screen筛分机screen烧结锰矿sintered manganese ore渗碳carbon penetration生铁pig iron石灰石lime stone石英quartz石墨电极graphitized electrode竖炉, 竖式电炉shaft electrical arc furnace 酸性渣acidic slag双壳电炉twin-shell electrical arc furnace 顺行smooth working四流连铸机four-strand CCM碳化钙calcium carbide碳素钢carbon steel碳素电极carbon electrode炭砖charcoal brick特殊钢special steel铜瓦copper content element添加剂additive铁合金ferro-alloy脱锭机, 脱模机ingot stripper脱磷dephosphorise脱硫desulphurise脱气degassing脱气剂degassing agent脱碳decarburization脱氧deoxidising脱引锭杆装置dummy bar disconnection device 弯曲辊bending roll弯曲应力bending stress弯曲装置bending device无烟煤,白煤bituminite下降烟罩操作法declined hood operation process 休风率downtime ratio悬挂支架suspension frame旋转浇铸台rotating casting table压下率screw-down rate氩氧脱碳argon-oxygen decarburization ACD氧枪oxygen lance冶炼设备melting equipment冶炼周期tap-to-tap cycle一炉钢one heat steel乙炔切割acetylene cutting异型钢材shapped bar引锭杆dummy bar引锭杆架dummy bar tilter引锭杆坑dummy bar pit引锭杆头dummy bar head萤石fluorite优质钢high-grade steel有效容积effective volume鱼尾板splice bar原料raw material原料跨raw material bay增碳carburize渣罐cinder pot渣铁比slag rate轧辊孔型设计roll pass design轧屑mill scale轧制道次pass轧制周期rolling cycle真空电弧精炼vacuum arc refining VAR真空脱气vacuum arc degassing VAD振动管运输机vibrating pipe conveyer镇静钢killed steel正偏差positive deviation支架辊back-up roll, supporting roll直流电弧炉DC electrical arc furnace中间罐tundish中间料仓intermediate bin中心铸管, 塞棒袖砖central pouring pipe, sleeve brick 珠光体钢pearlite steel铸模casting mould铸坯导辊strand guide roller转炉钢basic oxygen converter steel,basic oxygen furnace (BOF) steel自耗电极consumable electrode自焙电极self-baked electrode综合冶炼强度comprehensive rate of driving足辊foot roll钻孔机driller(5)轧钢Rolling八辊轧机MKW mill板坯slab半连续热带轧机semi-continuous hot-strip mill 薄板sheet薄板轧机sheet mill保温炉heat holding furnace扁锭slab ingot, slab扁钢flat bar不可逆轧机non-reversing mill步进梁式加热炉walking beam type furnace 槽钢channel车底式加热炉car bottom furnace车轮轧机railway-wheel mill车丝机threading machine成卷coiling成品包装跨packing bay初轧机blooming mill初轧坯翻转装置bloom turnover device出料拉杆kick-out arm穿孔机piercing mill粗轧机rough mill淬火炉hardening furnace搭接炉焊管机lap-welded pipe mill打包用带钢轧机package mill打捆机bundle machine打捆机bundler打印台stamping station大型型钢轧机heavy section mill导辊装置roller guide地上卷取机up coiler地下卷取机down coiler地下卷取机down coiler地下油库oil cellar地下运输机tunnel conveyer叠板轧机pack mill定径机sizing mill定心机centering machine镀槽coating bath镀锡板tinning sheet镀锡槽tinning bath镀锡线tinning line镀锌板galvanized sheet镀锌槽galvanizing bath镀锌线galvanizing line堆储跨storage bay堆垛机piler钝化处理passivation多辊矫直机multi-roll straightening machine 方钢square bar方坯bloom非连续性轧机non-continuous rolling mill飞锯flying saw干燥台drying station钢坯, 小方坯billet钢坯库billet store钢坯修磨conditioning高速线材轧机high speed wire rod mill高压水除鳞hydraulic jet descaler工字钢I-bar工字钢轧机I-beam mill工作辊换辊装置work roll changer工作辊支撑装置work roller supporting apparatus 钩式运输机hook transfer光亮退火炉bright annealing furnace轨梁轧机rail-beam section mill滚筒剪drum type shear横切机transversal shear厚板heavy plate厚板轧机heavy plate mill环形加热炉rotary hearth furnace换辊小车roll change carriage荒管, 毛管, 空心坯pierced billet, hollow billet回火炉tempering furnace回转剪rotary cropping shear活套loop活套张紧辊bridle roll机后输出辊道mill run-out table机架, 牌坊stand, housing机架辊breast roll机前输入辊道mill run-in table挤压机extruder夹送辊deflector pinch roll加热炉heating furnace碱槽alkaline bath剪切跨shear bay减径机reducing mill矫直机straightening machine, straightening mill角钢angle steel揭盖机cover carriage紧卷tight coil进料拉杆kick-in arm浸镀immersion coating井式炉pit batch type furnace精轧机finish mill精整加工线finishing machine精整跨finishing bay卷材, 线卷coil均热炉pit furnace均热炉跨soaking pit bay均整机,整径机(管) reeling machine开卷机, 拆卷机decoiler开坯机cogging mill可逆辊道reversing table空心坯减径机shell-reducing mill拉丝机wire-drawing machine扩径机(管) repiercing machine冷床cold bed冷锯cold saw冷轧板带钢cold rolled strip立辊vertical roll连续式加热炉continuous type furnace 连续酸洗continuous acid-washing链式运输机chain transfer磷化处理phosphate treatment磷酸phosphoric acid硫酸sulfurous acid炉卷机steckel mill炉用卷取机furnace coiler轮箍轧机tyre mill内表修磨inside grinding拧接头机coupling applicator盘条rod coil平立(万能)轧机horizontal-vertical (HV) mill 平整机temper machine破鳞辊descaling roll破鳞机scale breaker, descaler切边side crops切边剪end trimming shear切头top crops切头剪end shear切尾end crops去刺机deburring machine热处理heat treatment热带轧机hot-strip mill热镀hot-dip coating热锯hot saw热轧板带钢hot rolled strip乳化液emulsion森吉米尔轧机Sendzimir mill上料台架ingoing skid深冲薄钢板deep drawing sheet石油管套管pipe case收集台collecting table受料辊道receiving table输出辊道run-out table输入辊道run-in table水力除鳞hydraulic descaler水压试验机hydraulic pressure tester酸槽acid bath酸洗槽pickling bath酸洗工段pickling department酸洗机pickling machine酸洗线pickling line酸洗用酸acid for pickling甩尾back-end whip丝扣保护套thread protector四机架连续式带钢冷轧机four-stand tendem cold strip mill 松卷loose coil碎断剪chopping shear塔式酸洗机tower pickler套管接头pipe coupling铁皮坑scale pit通径机drifter筒式卷取机drum type coiler涂漆装置painting unit吐丝机laying head推钢机, 推杆pusher拖运机,移送机dragging device脱脂槽degreasing bath外表修磨outside grinding弯辊装置bending-up roll device万向连轴节universal spindle coupling无扭轧机non-twist mill无损探伤non destoryed test铣头机chamfering machine限动芯棒轧管机retained mandrel pipe mill硝酸nitric acid小型型钢轧机light section mill, merchant bar mill 芯棒式轧管机mandrel mill型钢, 条钢bar行星轧机planetary rolling mill修磨机grinder压下螺丝screw down压下装置, 压下机构screwdown延伸机elongator硬度试验机hardness tester油膜轴承oil film lubrication bearing预精轧机pre-finishing mill预热炉preheating furnace圆锭round ingot, round billet圆钢round bar圆盘锯circular saw运锭车, 翻锭车ingot buggy运输辊道processing table再加热炉reheating furnace轧边机, 立辊轧机edger轧钢rolling轧钢车间rolling plant轧管机设备tube mill equipment轧辊及辊道roller and table轧辊压下装置roller press-down device 轧辊轴承座roll bearing chock轧辊支架roll support轧机rolling mill轧机传动装置rolling mill drive device轧机跨mill bay, mill aisle轧机输出辊道mill delivery table轧机输入辊道mill approach table窄带strip张力减径机(管) tension-reducing machine 张力控制tension control罩式炉bell type furnace支撑辊back-up roll中板轧机medium plate mill中厚板medium plate中间辊道intermediate table中型宽带轧机medium wide-strip mill中型型钢轧机medium section mill中轧机intermediate mill周期式轧管机pilger mill转盘turntable自动轧管机plug mill纵切机longitudinal shear, slitting shear。

轧钢系统专业英语词汇

八辊轧机MKW mill板坯slab半连续热带轧机semi-continuous hot-strip mill 薄板sheet薄板轧机sheet mill保温炉heat holding furnace扁锭slab ingot, slab扁钢flat bar不可逆轧机non-reversing mill步进梁式加热炉walking beam type furnace 槽钢channel车底式加热炉car bottom furnace车轮轧机railway-wheel mill车丝机threading machine成卷coiling成品包装跨packing bay初轧机blooming mill初轧坯翻转装置bloom turnover device出料拉杆kick-out arm穿孔机piercing mill粗轧机rough mill淬火炉hardening furnace搭接炉焊管机lap-welded pipe mill打包用带钢轧机package mill打捆机bundle machine打捆机bundler打印台stamping station大型型钢轧机heavy section mill导辊装置roller guide地上卷取机up coiler地下卷取机down coiler地下卷取机down coiler地下油库oil cellar地下运输机tunnel conveyer叠板轧机pack mill定径机sizing mill定心机centering machine镀槽coating bath镀锡板tinning sheet镀锡槽tinning bath镀锡线tinning line镀锌板galvanized sheet镀锌槽galvanizing bath镀锌线galvanizing line堆储跨storage bay堆垛机piler钝化处理passivation多辊矫直机multi-roll straightening machine 方钢square bar方坯bloom非连续性轧机non-continuous rolling mill飞锯flying saw干燥台drying station钢坯, 小方坯billet钢坯库billet store钢坯修磨conditioning高速线材轧机high speed wire rod mill高压水除鳞hydraulic jet descaler工字钢I-bar工字钢轧机I-beam mill工作辊换辊装置work roll changer工作辊支撑装置work roller supporting apparatus 钩式运输机hook transfer光亮退火炉bright annealing furnace轨梁轧机rail-beam section mill滚筒剪drum type shear横切机transversal shear厚板heavy plate厚板轧机heavy plate mill环形加热炉rotary hearth furnace换辊小车roll change carriage荒管, 毛管, 空心坯pierced billet, hollow billet回火炉tempering furnace回转剪rotary cropping shear活套loop活套张紧辊bridle roll机后输出辊道mill run-out table机架, 牌坊stand, housing机架辊breast roll机前输入辊道mill run-in table挤压机extruder夹送辊deflector pinch roll加热炉heating furnace碱槽alkaline bath剪切跨shear bay减径机reducing mill矫直机straightening machine,straightening mill角钢angle steel揭盖机cover carriage紧卷tight coil进料拉杆kick-in arm浸镀immersion coating井式炉pit batch type furnace精轧机finish mill精整加工线finishing machine精整跨finishing bay卷材, 线卷coil均热炉pit furnace均热炉跨soaking pit bay均整机,整径机(管) reeling machine开卷机, 拆卷机decoiler开坯机cogging mill可逆辊道reversing table空心坯减径机shell-reducing mill拉丝机wire-drawing machine扩径机(管) repiercing machine冷床cold bed冷锯cold saw冷轧板带钢cold rolled strip立辊vertical roll连续式加热炉continuous type furnace 连续酸洗continuous acid-washing链式运输机chain transfer磷化处理phosphate treatment磷酸phosphoric acid硫酸sulfurous acid炉卷机steckel mill炉用卷取机furnace coiler轮箍轧机tyre mill内表修磨inside grinding拧接头机coupling applicator盘条rod coil平立(万能)轧机horizontal-vertical (HV) mill 平整机temper machine破鳞辊descaling roll破鳞机scale breaker, descaler切边side crops切边剪end trimming shear切头top crops切头剪end shear切尾end crops去刺机deburring machine热处理heat treatment热带轧机hot-strip mill热镀hot-dip coating热锯hot saw热轧板带钢hot rolled strip乳化液emulsion森吉米尔轧机Sendzimir mill上料台架ingoing skid深冲薄钢板deep drawing sheet石油管套管pipe case收集台collecting table受料辊道receiving table输出辊道run-out table输入辊道run-in table水力除鳞hydraulic descaler水压试验机hydraulic pressure tester酸槽acid bath酸洗槽pickling bath酸洗工段pickling department酸洗机pickling machine酸洗线pickling line酸洗用酸acid for pickling甩尾back-end whip丝扣保护套thread protector四机架连续式带钢冷轧机four-stand tendem cold strip mill 松卷loose coil碎断剪chopping shear塔式酸洗机tower pickler套管接头pipe coupling铁皮坑scale pit通径机drifter筒式卷取机drum type coiler涂漆装置painting unit吐丝机laying head推钢机, 推杆pusher拖运机,移送机dragging device脱脂槽degreasing bath外表修磨outside grinding弯辊装置bending-up roll device万向连轴节universal spindle coupling无扭轧机non-twist mill无损探伤non destoryed test铣头机chamfering machine限动芯棒轧管机retained mandrel pipe mill硝酸nitric acid小型型钢轧机light section mill, merchant bar mill 芯棒式轧管机mandrel mill型钢, 条钢bar行星轧机planetary rolling mill修磨机grinder压下螺丝screw down压下装置, 压下机构screwdown延伸机elongator硬度试验机hardness tester油膜轴承oil film lubrication bearing预精轧机pre-finishing mill预热炉preheating furnace圆锭round ingot, round billet圆钢round bar圆盘锯circular saw运锭车, 翻锭车ingot buggy运输辊道processing table再加热炉reheating furnace轧边机, 立辊轧机edger轧钢rolling轧钢车间rolling plant轧管机设备tube mill equipment轧辊及辊道roller and table轧辊压下装置roller press-down device轧辊轴承座roll bearing chock轧辊支架roll support轧机rolling mill轧机传动装置rolling mill drive device轧机跨mill bay, mill aisle轧机输出辊道mill delivery table轧机输入辊道mill approach table窄带strip张力减径机(管) tension-reducing machine 张力控制tension control罩式炉bell type furnace支撑辊back-up roll中板轧机medium plate mill中厚板medium plate中间辊道intermediate table中型宽带轧机medium wide-strip mill中型型钢轧机medium section mill中轧机intermediate mill周期式轧管机pilger mill转盘turntable自动轧管机plug mill纵切机longitudinal shear, slitting shear。

轧钢英语大全

轧钢专业词汇表

轧钢专业英语必备词汇[1]1

轧钢专业词汇

轧钢英语词汇汇总

轧钢专业英语必备词汇

轧钢专业英语词汇1

轧钢专业英语集锦

轧钢 钢材行业 专业英语

轧钢专业英语必备词汇

轧钢专业英语必备词汇

轧钢专业英语词汇

轧钢专有名词英语集 (1)

轧钢专业英语单词

轧钢词汇-working

轧钢专业词汇

轧钢专业英语

(完整版)轧钢英语大全

轧钢专业词汇

轧钢系统专业英语词汇

轧钢钢材行业专业英语