GB818 十字盘头螺钉 圆头机螺丝 电镀锌
螺钉规格标准——GB标准
螺钉规格标准——GB标准【大中小发布时间：2006-08-24 08:48:24 浏览次数：1677 】规格标准——GB标准开槽圆柱头螺钉 GB /T 65-2000开槽盘头螺钉 GB /T 67-2000开槽沉头螺钉 GB /T 68-2000开槽半沉头螺钉 GB /T 69-2000内六角圆柱头螺钉 GB /T 70.1-2000内六角平圆头螺钉 GB /T 70.2-2000内六角沉头螺钉 GB /T 70.3-2000开槽锥端紧定螺钉 GB 71-85开槽锥端定位螺钉 GB 72-88开槽平端紧定螺钉 GB 73-85开槽凹端紧定螺钉 GB 74-85开槽长圆柱端紧定螺钉 GB 75-85内六角平端紧定螺钉 GB /T 77-2000内六角锥端紧定螺钉 GB /T 78-2000内六角圆柱端紧定螺钉 GB /T 79-2000内六角凹端紧定螺钉 GB /T 80-2000方头长圆柱球面端紧定螺钉 GB 83-88方头凹端紧定螺钉 GB 84-88方头长圆柱端紧定螺钉 GB 85-88方头短圆柱锥端紧定螺钉 GB 86-88十字槽盘头螺钉 GB /T 818-2000六角头不脱出螺钉 GB 838-88滚花头不脱出螺钉 GB 839-88塑料滚花头螺钉 GB 840-88开槽球面圆柱头轴位螺钉 GB 946-88开槽球面大圆柱头螺钉 GB 947-88开槽沉头不脱出螺钉 GB 948-88开槽半沉头不脱出螺钉 GB 949-88内六角花形盘头螺钉 GB 2672-86内六角花形沉头螺钉 GB 2673-86内六角花形半沉头螺钉 GB 2674-86内六角圆柱头轴肩螺钉 GB 5281-85内六角花形圆柱头螺钉-4.8级 GB 6190-86内六角花形圆柱头螺钉-8.8和10.9级 GB 6191-86精密机械用紧固件十字槽螺钉 GB /T 13806.1-92十字槽半沉头螺钉 GB /T 820-2000方头平端紧定螺钉 GB 821-88十字槽圆柱头螺钉 GB /T 822-2000十字槽小盘头螺钉 GB 823-88吊环螺钉 GB 825-88开槽盘头定位螺钉 GB 828-88开槽圆柱端定位螺钉 GB 829-88开槽圆柱头轴位螺钉 GB 830-88开槽无头轴位螺钉 GB 831-88开槽带孔球面圆柱头螺钉 GB 832-88开槽大圆柱头螺钉 GB 833-88滚花高头螺钉 GB 834-88滚花平头螺钉 GB 835-88滚花小头螺钉 GB 836-88如有侵权请联系告知删除，感谢你们的配合！。
螺钉规格标准——GB标准
螺钉规格标准——GB标准【大中小发布时间：2006-08-24 08:48:24 浏览次数：1677 】规格标准——GB标准开槽圆柱头螺钉GB /T 65-2000开槽盘头螺钉GB /T 67-2000开槽沉头螺钉GB /T 68-2000开槽半沉头螺钉GB /T 69-2000内六角圆柱头螺钉GB /T 70.1-2000内六角平圆头螺钉GB /T 70.2-2000内六角沉头螺钉GB /T 70.3-2000开槽锥端紧定螺钉GB 71-85开槽锥端定位螺钉GB 72-88开槽平端紧定螺钉GB 73-85开槽凹端紧定螺钉GB 74-85开槽长圆柱端紧定螺钉GB 75-85内六角平端紧定螺钉GB /T 77-2000内六角锥端紧定螺钉GB /T 78-2000内六角圆柱端紧定螺钉GB /T 79-2000内六角凹端紧定螺钉GB /T 80-2000方头长圆柱球面端紧定螺钉GB 83-88方头凹端紧定螺钉GB 84-88方头长圆柱端紧定螺钉GB 85-88方头短圆柱锥端紧定螺钉GB 86-88十字槽盘头螺钉GB /T 818-2000六角头不脱出螺钉GB 838-88滚花头不脱出螺钉GB 839-88塑料滚花头螺钉GB 840-88开槽球面圆柱头轴位螺钉GB 946-88开槽球面大圆柱头螺钉GB 947-88开槽沉头不脱出螺钉GB 948-88开槽半沉头不脱出螺钉GB 949-88内六角花形盘头螺钉GB 2672-86内六角花形沉头螺钉GB 2673-86内六角花形半沉头螺钉GB 2674-86内六角圆柱头轴肩螺钉GB 5281-85内六角花形圆柱头螺钉-4.8级GB 6190-86内六角花形圆柱头螺钉-8.8和10.9级GB 6191-86 精密机械用紧固件十字槽螺钉GB /T 13806.1-92 十字槽半沉头螺钉GB /T 820-2000方头平端紧定螺钉GB 821-88十字槽圆柱头螺钉GB /T 822-2000十字槽小盘头螺钉GB 823-88吊环螺钉GB 825-88开槽盘头定位螺钉GB 828-88开槽圆柱端定位螺钉GB 829-88开槽圆柱头轴位螺钉GB 830-88开槽无头轴位螺钉GB 831-88开槽带孔球面圆柱头螺钉GB 832-88开槽大圆柱头螺钉GB 833-88滚花高头螺钉GB 834-88滚花平头螺钉GB 835-88滚花小头螺钉GB 836-88。
现行螺钉国家标准
GB/T 16824.1-1997
六角凸缘自攻螺钉
GB/T 16824.2-1997
六角法兰面自攻螺钉
GB/T 16938-1997
紧固件螺栓、螺钉、螺柱和螺母通用技术条件
GB/T 2670.1-2004
内六角花形盘头自攻螺钉
GB/T 2670.2-2004
内六角花形沉头自攻螺钉
GB/T 14210-1993
墙板自攻螺钉
GB/T 15856.1-2002
十字槽盘头自钻自攻螺钉
GB/T 15856.2-2002
十字槽沉头自钻自攻螺钉
GB/T 15856.3-2002
十字槽半沉头自钻自攻螺钉
GB/T 15856.4-2002
六角法兰面自钻自攻螺钉
GB/T 15856.5-2002
100°沉头不脱出螺钉
GJB 122.13-1986
固定表盘螺钉
GJB 122.14-1986
两边切平的接触螺钉
GJB 122.15-1986
双耳托板螺钉
GJB 122.7-1986
十字槽100°沉头螺钉
GJB 3372-1998
普通螺纹螺钉
GJB 3373-1998
ＭＪ螺纹螺钉
GJB 3375-1998
GB/T 86-1988
方头短圆柱锥端紧定螺钉
GB/T 878-2007
开槽无头螺钉
GB/T 884-1986
螺钉锁紧挡圈
GB/T 885-1986
带锁圈的螺钉锁紧挡圈
GB/T 891-1986
螺钉紧固轴端挡圈
GB/T 9074.10-1988
十字槽半沉头螺钉和锥形锁紧垫圈组合件
十字槽小盘头螺钉标准
十字槽小盘头螺钉标准十字槽小盘头螺钉是一种常见的紧固件，其标准化生产对于保证产品质量、提高生产效率具有重要意义。
本文将对十字槽小盘头螺钉的标准进行介绍，以便相关行业人士了解其相关知识。
首先，十字槽小盘头螺钉的标准主要包括尺寸标准和材质标准两个方面。
在尺寸标准方面，十字槽小盘头螺钉的直径、长度、螺纹规格等都有严格的标准要求，以保证其在使用时能够与其他零部件配合良好，达到预期的紧固效果。
而在材质标准方面，十字槽小盘头螺钉通常采用碳钢、合金钢等材质制造，其具体的材质标准也需要符合国家或行业标准，以确保产品的质量和可靠性。
其次，十字槽小盘头螺钉的标准还涉及到表面处理和性能要求。
在表面处理方面，通常会对螺钉的表面进行镀锌、镀镍等防腐处理，以增加其耐腐蚀性能，延长使用寿命。
而在性能要求方面，十字槽小盘头螺钉需要具备一定的拉伸强度、抗剪强度、硬度等机械性能，以满足不同工程场合的使用需求。
此外，十字槽小盘头螺钉的标准还包括了生产工艺和检验要求。
生产工艺要求主要指导了螺钉的生产工艺流程、设备要求、工艺控制等方面，以保证产品的一致性和稳定性。
而检验要求则包括了对螺钉外观质量、尺寸偏差、力学性能等方面的检验方法和标准，以确保产品符合相关标准和规定。
总的来说，十字槽小盘头螺钉的标准化生产对于产品质量和生产效率具有重要意义。
只有严格遵循相关标准要求，才能生产出符合要求的产品，满足市场和客户的需求。
因此，相关企业和生产厂家应当加强对十字槽小盘头螺钉标准的学习和理解，不断提升自身的生产水平和技术能力，为行业发展做出贡献。
综上所述，十字槽小盘头螺钉标准的重要性不言而喻。
只有严格遵循相关标准要求，才能生产出高质量的产品，满足市场和客户的需求。
希望本文能够对相关行业人士有所帮助，促进行业的健康发展。
(整理)紧固件GB标准
紧固件常用GB标准∙(ISO 7380-1997) 内六角平圆头螺钉GB/T 70.2-2000∙(ISO 4762-1997)(GB 70-1985) 内六角圆柱头螺钉GB/T 70.1-2000 ∙十字槽盘头螺钉818-85 GB/T 818-2000∙六角头螺栓全螺纹GB/T 5783-2000∙1型六角螺母GB/T 6170-2000∙六角薄螺母GB/T 6172.1-2000∙盖形螺母GB/T 923-88∙标准型弹簧垫圈GB/T 93-87∙内六角沉头螺钉GB/T 70.3-2000∙内六角凹端紧定螺钉GB/T 80-2000∙平垫圈A级GB/T 97.1-2002∙钢结构用高强度垫圈GB/T 1230-91∙钢结构用高强度大六角头螺母GB/T 1229-91∙钢结构用高强度大六角头螺栓GB/T 1228-91∙大半圆头方颈螺栓C级GB/T 14-1998∙半圆头方颈螺栓GB/T 12-88∙十字槽小盘头螺钉GB/T 823-88∙等长双头螺柱B级GB/T 901-88∙十字槽沉头螺钉第1部分：钢4.8级GB/T 819.1-2000∙开口型扁圆头抽芯铆钉GB/T 12618-90∙圆柱销不淬硬钢和奥氏体不锈钢GB/T 119.1-2000∙十字槽沉头自攻螺钉GB/T 846-85∙十字槽盘头自攻螺钉GB/T 845-85∙小垫圈A级GB/T 848-2002∙大垫圈A级GB/T 96.1-2002∙六角头螺栓GB/T 5782-20001. 螺栓∙六角头螺栓细牙Hexagon head bolts with fine pitch threadGB/T 5785-2000 | 代替GB/T 5785-1986∙六角头螺栓细牙全螺纹Hexagon head bolts with fine pitch thread-Full thread GB/T 5786-2000 | 代替GB/T 5786-1986∙六角法兰面螺栓-加大系列-B级Hexagon flange bolts-Heavy series-product grade B GB/T 5789-86 | UDC 621.882.6∙六角法兰面螺栓-加大系列-细杆-B级Hexagon flange bolts-Heavy series-product grade B GB/T 5790-86 | UDC 621.882.6∙六角法兰面螺栓小系列Hexagon flange bolts-Small seriesGB/T 16674-1996 | 代替GB/T 5787、5788-1986∙钢网架螺栓球节点用高强度螺栓High strength bolts for joints of space grid structures GB/T 16939-1997∙扩口式管接头空心螺栓Flared type tube fittings Inverted flare boltsGB 5650∙GB/T 3098.13-1996 紧固件机械性能螺栓与螺钉GB/T 3098.13-1996 紧固件机械性能螺栓与螺钉3098∙GB18230.2-2000 栓接结构用大六角螺栓短螺纹GB18230.2-2000 栓接结构用大六角螺栓短螺纹GB18230.2-2000∙U型螺栓U-boltsJB/ZQ 4321-97 | 代替JB/ZQ 4321-86∙大半圆头带榫螺栓Cup head nib bolts with large headGB/T 15-88 | UDC 621.882.6 | 代替GB15-76∙六角头铰制孔用螺栓Hexagon fit bolts-product grade A and BGB/T 27-88 | UDC 621.882.6 | 代替GB27-76∙六角头螺杆带孔铰制孔用螺栓Hexagon fit bolts with split pin hole on shank-product grade A and BGB/T 28-88 | UDC 621.882.6 | 代替GB28-76∙六角头头部带槽螺栓A 和B 级Hexagon bolts with slot on head -product A and B GB/T 29.1-88 | UDC 621.882.6 | 代替GB29-76∙十字槽凹穴六角头螺栓Cross recessed hexagon bolts with indentationGB/T 29.2-88 | UDC 621.882.6 | 代替GB29-76∙下方头螺栓B级Square head bolts with small head-praduct grade BGB/T 35-88 | UDC 621.882.6 | 代替GB35-76∙T 形槽用螺栓Bolts for T-SlotGB/T 37-88 | UDC 621.882.6 | 代替GB37-76∙加强半圆头方颈螺栓Strengthened cup head square neck boltsGB/T 794-93 | 代替GB794-67∙六角头螺杆带孔螺栓Hexagon bolts with split pin hole on shank-product grade A and B GB/T 31.1-88 | UDC 621.882.6 | 代替GB31、23、24-76∙六角头螺杆带孔螺栓细杆B级Hexagon bolts with split pin hole on shank-Reduced shank-product grade BGB/T 31.2-88 | UDC 621.882.6 | 代替GB31、23、24-76∙六角头螺杆带孔螺栓细牙A和B级Hexagon bolts with split pin hole on shank-Fine pitch thread-product grade A and BGB/T 31.3-88 | UDC 621.882.6 | 代替GB31、23、24-76∙方头螺栓C级Square head bolts-Product grade CGB/T 8-88 | UDC 621.882.6 | 代替GB8-76∙沉头方颈螺栓Flat countersunk square neck boltsGB/T 10-88 | UDC 621.882.6 | 代替GB10-76∙沉头带榫螺拴Flat countersunk nib boltsGB/T 11-88 | UDC 621.882.6 | 代替GB11-76∙半圆头带榫螺栓Cup head nid boltsGB/T 13-88 | UDC 621.882.6 | 代替GB13-76∙六角头头部带孔螺栓A 和B级Hexagon bolts with wire holes on head-product grade A and B GB/T 32.1-88 | UDC 621.882.6 | 代替GB32、25、26-76∙六角头头部带孔螺栓细杆B级Hexagon bolts with wire holes on head-Reduced shank-product grade BGB/T 32.2-88 | UDC 621.882.6 | 代替GB32、25、26-76∙六角头头部带孔螺栓细牙A 和B 级Hexagon bolts with wire holes on head-Fine pitch thread-product grade A and BGB/T 32.3-88 | UDC 621.882.6 | 代替GB32、25、26-76∙活节螺栓Eye boltsGB/T 798-88 | UDC 621.882.6 | 代替GB798-76∙地脚螺栓Eyelet boltsGB/T 799-88 | UDC 621.882.6 | 代替GB799-76∙沉头双榫螺Flat countersunk double nib boltsGB/T 800-88 | UDC 621.882.6 | 代替GB800-77∙小半圆头低方颈螺栓B级Cup head square neck bolts with small head and short neck-product grade BGB/T 801-1998 | 代替GB801-88∙六角头螺栓C级Hexagon head bolts-product grade CGB/T 5780-2000 | 代替GB/T 5780-1986∙六角头螺栓全螺纹C级Hexagon head bolts-Full thread-product grade C GB/T 5781-2000 | 代替GB/T 5781-1986∙六角头螺栓-细杆-B级Hexagon head bolts-Reduced shank -Product grade B GB/T 5784-86 | UDC 621.882.6 | 代替GB30、21-76∙六角头螺栓Hexagon head boltsGB/T 5782-2000 | 代替GB/T 5782-1986∙六角头螺栓全螺纹Hexagon head bolts-Full threadGB/T 5783-2000 | 代替GB/T 5783-1986∙大半圆头方颈螺栓C级Cup head square neck bolts with large head-Product grade C GB/T 14-1998 | 代替GB14-88∙半圆头方颈螺栓Cup head square neck boltsGB/T 12-88 | UDC 621.882.6 | 代替GB12-762.螺钉∙方头长圆柱球面端紧定螺钉Square set screws with long dog point and rounded end GB/T 83-88 | UDC 621.882.2 | 代替GB83-76∙开槽圆柱头轴位螺钉Slotted cheese head screws with shoulderGB/T 830-88 | UDC 621.882.2 | 代替GB830-76∙开槽无头轴位螺钉Slotted shoulder screwsGB/T 831-88 | UDC 621.882.2 | 代替GB831-76∙开槽带孔球面圆柱头螺钉Slotted capstan screwsGB/T 832-88 | UDC 621.882.2 | 代替GB832-76∙开槽圆柱头螺钉Slotted cheese head screwsGB/T 65-2000 | 代替GB/T 65-1985∙开槽盘头螺钉Slotted pan head screwsGB/T 67-2000 | 代替GB/T 67-1985∙开槽沉头螺钉Slotted countersunk flat head screws (common head style) GB/T 68-2000 | 代替GB/T 68-1985∙开槽半沉头螺钉Countersunk slotted raised head screws (common head style) GB/T 69-2000 | 代替GB/T 69-1985∙开槽锥端紧定螺钉Slotted set screws with cone pointGB/T 71-85 | UDC 621.882.219 | 代替GB71-76∙开槽锥端定位螺钉Slotted setscrews with cone pointGB/T 72-88 | UDC 621.882.2 | 代替GB72-76∙开槽平端紧定螺钉Slotted set screws with flat pointGB/T 73-85 | UDC 621.882.219.4 | 代替GB73-76∙滚花高头螺钉Knurled thumb screwsGB/T 834-88 | UDC 621.882.2 | 代替GB834-76∙滚花平头螺钉Knurled screwsGB/T 835-88 | UDC 621.882.2 | 代替GB835-76∙滚花小头螺钉Knurled screws with small headGB/T 836-88 | UDC 621.882.2 | 代替GB836-76∙开槽盘头不脱出螺钉Slotted pan head screws with waisted shankGB/T 837-88 | UDC 621.882.2 | 代替GB837-76∙方头短圆柱锥端紧定螺钉Square set screws with short dog point and cone end GB/T 86-88 | UDC 621.882.2 | 代替GB86-76∙开槽凹端紧定螺钉Slotted set screws with cup pointGB/T 74-85 | UDC 621.882.219.4.092.6 | 代替GB74-76∙方头长圆柱端紧定螺钉Square set screws with long dog pointGB/T 85-88 | UDC 621.882.2 | 代替GB85-76∙十字槽半沉头螺钉Countersunk raised head screws (common head style) with cross recess GB/T 820-2000 | 代替GB/T 820-1985∙开槽圆柱端定位螺钉Slotted setscrews with dog pointGB/T 829-88 | UDC 621.882.2 | 代替GB829-76∙开槽大圆柱头螺钉Slotted large cheese head screwsGB/T 833-88 | UDC 621.882.2 | 代替GB833-76∙六角头不脱出螺钉Hexagon screws with waisted shankGB/T 838-88 | UDC 621.882.2 | 代替GB838-76∙十字槽沉头螺钉第2部分：钢8.8、不锈钢A2-70和有色金属CU2或CU3 Cross recessed countersunk flat head screws (common head style)-Grade A-Part 2:Steel of property class 8.8, stainless and non-ferrous metalsGB/T 819.2-1997∙方头平端紧定螺钉Square set screws with chamfered endGB/T 821-88 | UDC 621.882.2 | 代替GB821-76∙十字槽圆柱头螺钉Cheese head screws with cross recessGB/T 822-2000 | 代替GB/T 822-1988∙吊环螺钉EyeboltsGB/T 825-88 | UDC 621.882 | 代替GB825-76∙精密机械用紧固件十字槽螺钉Fasteners for mechanics-Cross recessed screws GB/T 13806.1-92∙方头凹端紧定螺钉Square set screws with cup pointGB/T 84-88 | UDC 621.882.2 | 代替GB84-76∙开槽盘头定位螺钉Slotted pan head set setscrews with dog pointGB/T 828-88 | UDC 621.882.2 | 代替GB828-76∙滚花头不脱出螺钉Knurled thumb screws with waisted shankGB/T 839-88 | UDC 621.882.2 | 代替GB839-76∙塑料滚花头螺钉Plastic diamond knurlhead screwsGB/T 840-88 | UDC 621.882.2 | 代替GB840-79∙开槽球面圆柱头轴位螺钉Slotted raised head with shoulderGB/T 946-88 | UDC 621.882.2 | 代替GB946-76∙开槽球面大圆柱头螺钉Slotted large raised cheese head screwsGB/T 947-88 | UDC 621.882.2 | 代替GB947-76∙开槽沉头不脱出螺钉Slotted countersunk head screws with waisted shank GB/T 948-88 | UDC 621.882.2 | 代替GB948-76∙开槽半沉头不脱出螺钉Slotted raised countersunk head screws with waisted shank GB/T 949-88 | UDC 621.882.2 | 代替GB949-76∙开槽长圆柱端紧定螺钉Slotted set screws with long dog pointGB/T 75-85 | UDC 621.882.219.4.092.5 | 代替GB75-76∙十字槽小盘头螺钉Cross recessed small pan head screwsGB/T 823-88 | UDC 621.882.2 | 代替GB823-76∙十字槽盘头螺钉818-85 Pan head screws with cross recessGB/T 818-2000 | 代替GB/T 818-1985∙十字槽沉头螺钉第1部分：钢4.8级Countersunk flat head screws (common head style)with cross recess-Part 1:Steel of property class 4.8GB/T 819.1-2000 | 代替GB/T 819-1985∙GB70.2-2000(ISO 7380-1997) 内六角平圆头螺钉Hexagon socket flat head screws GB70.2-2000(ISO 7380-1997 | 代替GB70.2-2000(ISO 7380-19973. 内六角螺钉∙(ISO 4762-1997)(GB 70-1985) 内六角圆柱头螺钉Hexagon socket head cap screws GB/T 70.1-2000 | 代替GB/T 70-1985∙(ISO 7380-1997)内六角平圆头螺钉Hexagon socket button head screwsGB/T 70.2-2000∙内六角凹端紧定螺钉Hexagon socket set screws with cup pointGB/T 80-2000 | 代替GB/T 80-1985∙内六角沉头螺钉Hexagon socket countersunk head screwsGB/T 70.3-2000∙内六角花形半沉头螺钉Hexagon lobular socket raised countersunk head screws GB/T 2674-86 | UDC 621.882.2 | 代替GB2674-81∙内六角花形沉头螺钉Hexagon lobular socket countersunk head screwsGB/T 2673-86 | UDC 621.882.2 | 代替GB2673-81∙内六角花形盘头螺钉Hexagon lobular socket pan head screwsGB/T 2672-86 | UDC 621.882.2 | 代替GB2672-81∙内六角花形圆柱头螺钉-4.8级Hexagon lobular socket head cap screws-property class 4.8 GB/T 6190-86 | UDC 621.882.2 | 代替GB2671-81∙内六角花形圆柱头螺钉-8.8和10.9级Hexagon lobular socket head cap screws-property class8.8 and 10.9GB/T 6191-86 | UDC 621.882.2 | 代替GB2671-81∙内六角平端紧定螺钉Hexagon socket set screws with flat pointGB/T 77-2000 | 代替GB/T 77-1985∙内六角圆柱端紧定螺钉Hexagon socket set screws with dog pointGB/T 79-2000 | 代替GB/T 79-1985∙内六角圆柱头轴肩螺钉Hexagon socket head shoulder screwsGB/T 5281-85 | UDC 621.882.215.6∙内六角锥端紧定螺钉Hexagon socket set screws with cone pointGB/T 78-2000 | 代替GB/T 78-19854. 自攻螺钉∙十字槽半沉头自攻锁紧螺钉Cross recessed raised countersunk head thread forming screws GB/T 6562-86 | UDC 621.882∙六角头自攻锁紧螺钉Hexagon head thread forming screwsGB/T 6563-86 | UDC 621.882∙内六角花形圆柱头自攻锁紧螺钉Hexagon lobular socket thread forming screws GB/T 6564-86 | UDC 621.882∙十字槽半沉头自攻螺钉Cross recessed raised countersunk head tapping screws GB/T 847-85 | UDC 621.882.216.5.082.8 | 代替GB847-76∙开槽盘头自攻螺钉Slotted pan head tapping screwsGB/T 5282-85 | UDC 621.882.215.082.8∙开槽沉头自攻螺钉Slotted countersunkhead tapping screwsGB/T 5283-85 | UDC 621.882.215.082.8∙开槽半沉头自攻螺钉Slotted raised countersunkhead tapping screwsGB/T 5284-85 | UDC 621.882.215.082.8∙六角头自攻螺钉Hexagon head tapping screwsGB/T 5285-85 | UDC 621.882.215.082.8∙十字槽盘头自攻锁紧螺钉Cross recessed pan head thread forming screws GB/T 6560-86 | UDC 621.882∙十字槽沉头自攻锁紧螺钉Cross recessed countersunk head thread forming screws GB/T 6561-86 | UDC 621.882∙十字槽头凹穴六角头自攻螺钉Cross recessed hexagon head tapping screws with indentation GB/T 9456-88 | UDC 621.882.2∙精密机械用紧固件十字槽自攻螺钉刮削端Fasteners for fine mechanics-Cross recessed tapping screws-Scrape pointGB/T 13806.2-92∙墙板自攻螺钉Dry wall screwsGB/T 14210-93∙十字槽盘头自钻自攻螺钉Cross recessed pan head drilling screws with tapping screw thread GB/T 15856.1-2002 | 代替GB/T 15856.1-1995∙十字槽沉头自钻自攻螺钉Cross recessed countersunk head drilling screws with tapping screw threadGB/T 15856.2-2002 | 代替GB/T 15856.2-1995∙十字槽半沉头自钻自攻螺钉Cross recessed raised countersunk head drilling screws with tapping screw threadGB/T 15856.3-2002 | 代替GB/T 15856.3-1995∙六角法兰面自钻自攻螺钉Hexagon flange drilling screws with tapping screw thread GB/T 15856.4-2002 | 代替GB/T 15856.4-1995∙六角凸缘自钻自攻螺钉Hexagon washer head drilling screws with tapping screw thread GB/T 15856.5-2002∙六角凸缘自攻螺钉Hexzgon head tapping screws with collarGB/T 16824.1-1997∙六角法兰面自攻螺钉Hexagon flange head tapping screwsGB/T 16824.2-1997∙十字槽盘头自攻螺钉Cross recessed pan head tapping screwsGB/T 845-85 | UDC 621.882.216.5.082.8 | 代替GB845-76∙十字槽沉头自攻螺钉Cross recessed countersunk head tapping screwsGB/T 846-85 | UDC 621.882.216.5.082.8 | 代替GB846-765.木螺钉∙开槽半沉头木螺钉Slotted raised countersunk head wood screwsGB/T 101-86 | UDC 621.882.2 | 代替GB101-76∙开槽沉头木螺钉Slotted countersunk head wood screwsGB/T 100-86 | UDC 621.882.2 | 代替GB100-76∙开槽圆头木螺钉Slotted round head wood screwsGB/T 99-86 | UDC 621.882.2 | 代替GB99-76∙六角头木螺钉Hexagon head wood screwsGB/T 102-86 | UDC 621.882.2 | 代替GB102-76∙十字槽半沉头木螺钉Cross recessed raised head countersunk head wood screws GB/T 952-86 | UDC 621.882.2 | 代替GB952-76∙十字槽沉头木螺钉Cross recessed countersunk head wood screws GB/T 951-86 | UDC 621.882.2 | 代替GB951-76∙十字槽圆头木螺钉Cross recessed round head wood screwsGB/T 950-86 | UDC 621.882.2 | 代替GB950-766.螺杆和螺柱∙储能焊用焊接螺柱Weld studs for capacitor discharge weldingGB/T 902.3-89 | 代替GB902-76∙等长双头螺柱B级Double end studs(clamping type) -Product grade B GB/T 901-88 | UDC 621.882 | 代替GB901-76∙等长双头螺柱C级Double end studs(clamping type)-product grade C GB/T 953-88 | UDC 621.882 | 代替GB953-76∙机动弧焊用焊接螺柱Weld studs for arc weldingGB/T 902.2-89 | 代替GB902-76∙螺杆Threaded rodsGB/T 15389-94∙手工焊用焊接螺柱Weld studs for manual weldingGB/T 902.1-89 | 代替GB902-76∙双头螺柱bm=1.25d Double end studs-bm=1.25dGB/T 898-88 | UDC 621.882 | 代替GB898-76∙双头螺柱bm=1.5d Double end studs-bm=1.5dGB/T 899-88 | UDC 621.882 | 代替GB899-76∙双头螺柱bm=1d Double end studs-bm=1dGB/T 897-88 | UDC 621.882 | 代替GB897-76∙双头螺柱bm=2d Double end studs--bm=2dGB/T 900-88 | UDC 621.882 | 代替GB900-76∙等长双头螺栓Double end studs∙动负荷预应力螺柱Dynamic load prestressed studs∙阶端双头螺柱Order end double end studs∙双头螺栓Double end studs∙双头螺柱Double end studs∙双头螺柱Double end studs∙双头螺柱b1=1.25d Double end studs7.铆钉∙平头铆钉Flat head rivetsGB/T 109-86 | UDC 621.884 | 代替GB109-76∙标牌铆钉Rivets for name plateGB/T 827-86 | UDC 621.884 | 代替GB827-76∙半圆头铆钉(粗制) Round head rivets-BlackGB/T 863.1-86 | UDC 621.884 | 代替GB863-76∙小半圆头铆钉(粗制) Round head rivets with small head-Black GB/T 863.2-86 | UDC 621.884∙平锥头铆钉(粗制) Cone head rivets-BlackGB/T 864-86 | UDC 621.884 | 代替GB864-76∙沉头铆钉(粗制) Countersunk head rivets-BlackGB/T 865-86 | UDC 621.884 | 代替GB865-86∙半沉头铆钉(粗制) Oval countersunk head rivets-Black GB/T 866-86 | UDC 621.884 | 代替GB866-76∙半圆头铆钉Round head rivetsGB/T 867-86 | UDC 621.884 | 代替GB867-76∙平锥头铆钉Cone head rivetsGB/T 868-86 | UDC 621.884 | 代替GB868-76∙沉头铆钉Countersunk head rivetsGB/T 869-86 | UDC 621.884 | 代替GB869-76∙扁圆头击芯铆钉Flat round head drive rivetsGB/T 15855.1-1995∙半沉头铆钉Oval countersunk head rivetsGB/T 870-86 | UDC 621.884 | 代替GB870-76∙扁圆头铆钉Flat round head rivetsGB/T 871-86 | UDC 621.884 | 代替GB871-76∙扁平头铆钉Thin head rivetsGB/T 872-86 | UDC 621.884 | 代替GB872-76∙扁圆头半空心铆钉Oval head semi-tubular rivetsGB/T 873-86 | UDC 621.884 | 代替GB873-76∙120°沉头半空心铆钉120 degree countersunk head semi-tubular rivets GB/T 874-86 | UDC 621.884 | 代替GB874-76∙扁平头半空心铆钉Thin head semi-tubular rivetsGB/T 875-86 | UDC 621.884 | 代替GB875-76∙空心铆钉Tubular rivetsGB/T 876-86 | UDC 621.884 | 代替GB876-76∙120°沉头铆钉120 degree countersunk head rivetsGB/T 954-86 | UDC 621.884 | 代替GB954-76∙管状铆钉Pipe type rivetsGB/T 975-86 | UDC 621.884 | 代替GB975-76∙大扁圆头铆钉Truss head rivetsGB/T 1011-86 | UDC 621.884 | 代替GB1011-76∙120°半沉头铆钉120 degree oval countersunk rivetsGB/T 1012-86 | UDC 621.884 | 代替GB1012-76∙平锥头半空心铆钉Cone head semi-tubler rivetsGB/T 1013-86 | UDC 621.884 | 代替GB1013-76∙大扁圆头半空心铆钉Truss head semi-tublar rivetsGB/T 1014-86 | UDC 621.884 | 代替GB1014-76∙沉头半空心铆钉Countersunk head semi-tublar rivetsGB/T 1015-86 | UDC 621.884 | 代替GB1015-76∙无头铆钉Headless rivetsGB/T 1016-86 | UDC 621.884 | 代替GB1016-76∙封闭型扁圆头抽芯铆钉Mushroom head break mandrel closed end blind rivets GB/T 12615-90∙封闭型沉头抽芯铆钉120 deg flush head break mandrel closed end blind rivets GB/T 12616-90∙开口型沉头抽芯铆钉120 deg flush head break mandrel blind rivets GB/T 12617-90∙沉头击芯铆钉Countersunk head drive rivetsGB/T 15855.2-1995∙开口型扁圆头抽芯铆钉Mushroom head break mandrel blind rivets GB/T 12618-908.螺母∙滚花高螺母Knurled nut with collarGB/T 806-88 | UDC 621.882.3 | 代替GB806-76∙滚花薄螺母Knurled nutsGB/T 807-88 | UDC 621.882.3 | 代替GB807-76∙小六角特扁细牙螺母Small hexagon thin nuts-Fine pitch thread GB/T 808-88 | UDC 621.882.3 | 代替GB808-76∙嵌装圆螺母Lnsert round nutsGB/T 809-88 | UDC 621.882.3 | 代替GB809-76∙小圆螺母Small round nutsGB/T 810-88 | UDC 621.882.3 | 代替GB810-76∙圆螺母Round nutsGB/T 812-88 | UDC 621.882.3 | 代替GB812-76∙端面带孔圆螺母Round nuts with drilled holes in one faceGB/T 815-88 | UDC 621.882.3 | 代替GB815-76∙侧面带孔圆螺母Round nuts with set pin holes in sideGB/T 816-88 | UDC 621.882.3 | 代替GB816-79∙带槽圆螺母Slotted round nutsGB/T 817-88 | UDC 621.882.3 | 代替GB817-76∙1型非金属嵌件六角锁紧螺母Prevailing torque type hexagon nuts(with non-metallic insert),style 1GB/T 889.1-2000 | 代替GB/T 889-1986∙1型六角开槽螺母细牙A和B级Hexagon slotted and castle nuts,style 1-fine pitch thread-product grades A and BGB/T 9457-88 | UDC 621.882.3 | 代替GB57、58-76∙2型六角开槽螺母细牙A和B级Hexagon slotted and castle nuts,style 2--Fine pitch thread -Product grades A and BGB/T 9458-88 | UDC 621.882.3∙六角开槽薄螺母细牙A和B级Hexagon thin slotted nuts--Fine pitch thread -Product grades A and BGB/T 9459-88 | UDC 621.882.3 | 代替GB59、60-76∙焊接方螺母Square weld nutsGB/T 13680-92∙焊接六角螺母Hexagon weld nutsGB/T 13681-92∙平头铆螺母Flat head riveted nutsGB/T 17880.1-1999∙沉头铆螺母Countersunk head riveted nutsGB/T 17880.2-1999∙小沉头铆螺母Small countersunk head riveted nutsGB/T 17880.3-1999∙120°小沉头铆螺母120°Small countersunk head riveted nutsGB/T 17880.4-1999∙平头六角铆螺母Flat head hexagon riveted nutsGB/T 17880.5-1999∙精密机械用六角螺母Hexagon nuts for fine mechanicsGB/T 18195-2000∙1型非金属嵌件六角锁紧螺母细牙Prevailing torque type hexagon nuts(with non-metallic insert),style 1,with fine pitch threadGB/T 889.2-2000∙非金属嵌件六角锁紧薄螺母Prevailing torque type hexagon thin nuts(with non-metallic insert) GB/T 6072.2-2000∙六角薄螺母细牙Hexagon thin nuts(chamfered) with fine pitch threadGB/T 6173-2000 | 代替GB/T 6173-1986∙六角薄螺母无倒角Hexagon thin nuts(unchamfered)GB/T 6174-2000 | 代替GB/T 6174-1986∙1型六角螺母细牙Hexagon nuts,style 1,with fine pitch threadGB/T 6171-2000 | 代替GB/T 6171-1986∙方螺母C级Square nuts-product grade CGB/T 39-88 | UDC 621.882.3 | 代替GB39-76∙六角螺母C级Hexagon nuts-product grade CGB/T 41-2000 | 代替GB/T 41-1986∙六角厚螺母Hexagon thick nutsGB/T 56-88 | 代替GB56-76∙蝶形螺母Wing nutsGB/T 62-88 | UDC 621.882.3 | 代替GB62-76∙环形螺母Lifting nutsGB/T 63-88 | UDC 621.882.3 | 代替GB63-76∙组合式盖形螺母Acorn nutsGB/T 802-88 | UDC 621.882.3 | 代替GB802-76∙球面六角螺母Hexagon nuts with raised faceGB/T 804-88 | UDC 621.882.3 | 代替GB804-76∙2型六角螺母Hexagon nuts,style 2GB/T 6175-2000 | 代替GB/T 6175-1986∙2型六角螺母细牙Hexagon nuts,style 2,with fine pitch threadGB/T 6176-2000 | 代替GB/T 6176-1986∙六角法兰面螺母Hexagon nuts with flangeGB/T 6177.1-2000 | 代替GB/T 6177-1986∙六角法兰面螺母细牙Hexagon nuts with flange-fine pitch threadGB/T 6177.2-2000∙1型六角开槽螺母-A和B级Hexagon slotted and castle nuts,style 1 -product grades A and B GB/T 6178-86 | UDC 621.882.3 | 代替GB57~58-76∙1型六角开槽螺母-C级Hexagon slotted nuts,style 1 -product grade CGB/T 6179-86 | UDC 621.882.3 | 代替GB57~58-76∙2型六角开槽螺母-A和B级Hexagon slotted and castle nuts,style 2 -Product grades A and B GB/T 6180-86 | UDC 621.882.3∙六角开槽薄螺母-A和B级Hexagon thin slotted nuts-Product grades A and B GB/T 6181-86 | UDC 621.882.3 | 代替GB59~60-76∙2型非金属嵌件六角锁紧螺母Prevailing torque type hexagon nuts(with non-metallic insert),style 2GB/T 6182-2000 | 代替GB/T 6182-1986∙非金属嵌件六角法兰面锁紧螺母Prevailing torque type hexagon nuts with flange(with non-metallic insert)GB/T 6183.1-2000 | 代替GB/T 6183-1986∙非金属嵌件六角法兰面锁紧螺母细牙Prevailing torque type hexagon nuts with flange(with non-metallic insert)with fine pitch threadGB/T 6183.2-2000∙1型全金属六角锁紧螺母Prevailing torque type all-metal hexagon nuts,style 1 GB/T 6184-2000 | 代替GB/T 6184-1986∙2型全金属六角锁紧螺母Prevailing torque type all-metal hexagon nuts,style 2 GB/T 6185.1-2000 | 代替GB/T 6185-1986∙2型全金属六角锁紧螺母细牙Prevailing torque type all-metal hexagon nuts,style 2,with fine pitch threadGB/T 6185.2-2000∙2型全金属六角锁紧螺母9级Prevailing torque type all-metal hexagon nuts,style 2-Property class 9GB/T 6186-2000 | 代替GB/T 6186-1986∙全金属六角法兰面锁紧螺母Prevailing torque type all-metal hexagon nuts with flange GB/T 6187.1-2000 | 代替GB/T 6187-1986∙全金属六角法兰面锁紧螺母细牙Prevailing torque type all-metal hexagon nuts with flange with fine pitch threadGB/T 6187.2-2000∙扣紧螺母Tight nutsGB/T 805-88 | UDC 621.882.3 | 代替GB805-76∙六角薄螺母Hexagon thin nuts(chamfered)GB/T 6172.1-2000 | 代替GB/T 6172-1986∙1型六角螺母Hexagon nuts,style 1GB/T 6170-2000 | 代替GB/T 6170-1986∙盖形螺母Acorn nutsGB/T 923-88 | UDC 621.882.3 | 代替GB923-769.垫圈∙工字钢用方斜垫圈Square taper washers for I sectionGB/T 852-88 | UDC 621.882.4 | 代替GB852-76∙槽钢用方斜垫圈Square taper washers for slot sectionGB/T 853-88 | UDC 621.882.4 | 代替GB853-76∙单耳止动垫圈Tab washers with long tabGB/T 854-88 | UDC 621.882.4 | 代替GB854-76∙双耳止动垫圈Tab washers with long tab and wingGB/T 855-88 | UDC 621.882.4 | 代替GB855-76∙外舌止动垫圈External tab washersGB/T 856-88 | UDC 621.882.4 | 代替GB856-76∙圆螺母用止动垫圈Tab washers for round nutGB/T 858-88 | UDC 621.882.4 | 代替GB858-76∙轻型弹簧垫圈Single coil spring lock washers,Light type GB/T 859-87 | UDC 621.882.4 | 代替GB859-76∙鞍形弹性垫圈Curved spring washersGB/T 860-87 | UDC 621.882.4 | 代替GB860-76∙内齿锁紧垫圈Lock washers internal teethGB/T 861.1-87 | UDC 621.882.4 | 代替GB861-76∙内锯齿锁紧垫圈Serrated lock washers internal teethGB/T 861.2-87 | UDC 621.882.4∙外齿锁紧垫圈Lock washers external teethGB/T 862.1-87 | UDC 621.882.4 | 代替GB862-76∙外锯齿锁紧垫圈Serrated lock washers external teethGB/T 862.2-87 | UDC 621.882.4∙波形弹性垫圈Wave spring washersGB/T 955-87 | UDC 621.882.4 | 代替GB955-76∙锥形锁紧垫圈Countersunk external toothed lock washers GB/T 956.1-87 | UDC 621.882.4 | 代替GB956-76∙锥形锯齿锁紧垫圈Countersunk Serrated external toothed lock washers GB/T 956.2-87 | UDC 621.882.4∙特大垫圈C级Plain washers-Extra large series-Product grade C GB/T 5287-2002 | 代替GB/T 5287-1985∙重型弹簧垫圈Single coil spring lock washers,heavy type GB/T 7244-87 | UDC 621.882.4∙鞍形弹簧垫圈Curved Single coil spring lock washersGB/T 7245-87 | UDC 621.882.4∙波形弹簧垫圈Wave Single coil spring lock washersGB/T 7246-87 | UDC 621.882.4∙大垫圈C级Plain washers-Large series-Product grade CGB/T 96.2-2002 | 代替GB/T 96-1985∙平垫圈倒角型A级Plain washers,chamfered-Product grade AGB/T 97.2-2002 | 代替GB/T 97.2-1985∙平垫圈用于螺钉和垫圈组合件Plain washers for screw and washer assemblies GB/T 97.4-2002 | 代替GB/T 9074.24、9074.25-1988∙球面垫圈Washers with ball faceGB/T 849-88 | UDC 621.882.4 | 代替GB849-76∙锥面垫圈Washers with cone faceGB/T 850-88 | UDC 621.882.4 | 代替GB850-76∙开口垫圈Washers with splitGB/T 851-88 | UDC 621.882.4 | 代替GB851-76∙平垫圈用于自攻螺钉和垫圈组合件Plain washers for tapping screw and washer assemblies GB/T 97.5-2002 | 代替GB/T 9074.29、9074.30-1988∙平垫圈C级Plain washers-Product grade CGB/T 95-2002 | 代替GB/T 95-1985∙销轴用平垫圈Plain washers for clevis pinsGB/T 97.3-2000∙平垫圈A级Plain washers-Product grade AGB/T 97.1-2002 | 代替GB/T 97.1-1985∙标准型弹簧垫圈Single coil spring lock washers Normal typeGB/T 93-87 | UDC 621.882.4 | 代替GB93-76∙大垫圈A级Plain washers-Large series-Product grade AGB/T 96.1-2002 | 代替GB/T 96-1985∙小垫圈A级Plain washers-small series-Product grade AGB/T 848-2002 | 代替GB/T 848-198510.组合件和连接副∙六角头螺栓、弹簧垫圈和平垫圈组合件Hexagon head bolt,single coil spring lock washer and plain washer assembliesGB/T 9074.17-88 | UDC 621.882∙自攻螺钉和平垫圈组合件Tapping screw and washer assemblies with plain washers GB/T 9074.18-2002 | 代替GB/T 9074.18、9074.19、9074、22、9074、23-1988∙十字槽凹穴六角头自攻螺钉和平垫圈组合件Cross recessed hexagon head tapping screw with indentation and plain washer assembliesGB/T 9074.20-88 | UDC 621.882∙十字槽凹穴六角头自攻螺钉和大垫圈组合件Cross recessed hexagon head tapping sorew with indentation and large plain washer assembliesGB/T 9074.21-88 | UDC 621.882∙组合件用弹簧垫圈Single coil spring lock washer for assemblyGB/T 9074.26-88 | UDC 621.882∙组合件用外锯齿锁紧垫圈Serrated lock washer external teeth for assembly GB/T 9074.27-88 | UDC 621.882∙组合件用锥形锁紧垫圈Lountersunk external toothed lock washer for assembly GB/T 9074.28-88 | UDC 621.882∙腰状杆螺柱连接副型式分类Connections with waisted stud-Tape classification GB/T 13807.1-92∙腰状杆螺柱连接副螺柱Connections with waisted stud-StudsGB/T 13087.2-92∙腰状杆螺柱连接副螺母、受力套管Connections with waisted stud-Nuts,extension sleeves GB/T 13087.3-92∙栓接结构用大六角头螺栓螺纹长度按GB/T 3106 C级8.8和10.9级Hexagon bolts for high-strength structural bolting with large width across flats(thread lengths according to GB/T3106)-Product grade C-Property classes 8.8 and 10.9GB/T 18230.1-2000∙栓接结构用大六角头螺栓短螺纹长度C级8.8和10.9级Hexagon bolts for high-strengthstructural bolting with large width across flats(short thread length)-Product gradeC-property classes 8.8 and 10.9GB/T 18230.2-2000∙栓接结构用大六角头螺母B级8和10级Hexagon nuts for high-strength structural bliting with large width across flats-Product grade B-Property classes 8 and 10GB/T 18230.3-2000∙栓接结构用1型大六角螺母B级10级Hexagon nuts for structural bolting with large width across flats,style 1-Product grade B-Property class 10GB/T 18230.4-2000∙栓接结构用平垫圈淬火并回火Plain washers for high-strength structural bolting hardened and temperedGB/T 18230.5-2000∙栓接结构用1型大六角螺母浸热镀锌(加大攻丝尺寸) A和B级5.6和8级Hexagon nuts for structural bolting,style 1,hot-dip galvanized(oversize tapped)-Product grade A and B-Property classes5.6 and 8GB/T 18230.6-2000∙栓接结构用2型大六角螺母浸热镀锌(加大攻丝尺寸) A级9级Hexagon nuts for structural bolting,style 2,hot-dip galvanized(oversize tapped)-Product grade A -Property class 9GB/T 18230.7-2000∙十字槽半沉头螺钉和锥形锁紧垫圈组合件Cross recessed raised countersunk head screw and countersunk external toothed lock washer assembliesGB/T 9074.10-88 | UDC 621.882∙十字槽凹穴六角头螺栓和弹簧垫圈组合件Cross recessed hexagon bolt with indetation single coil spring lock washer assembliesGB/T 9074.12-88 | UDC 621.882∙十字槽凹穴六角头螺栓、弹簧垫圈和平垫圈组合件Cross recessed hexagon bolt with indetation,single coil lock washer and plain washer assembliesGB/T 9074.13-88 | UDC 621.882∙钢结构用扭剪型高强度螺栓连接副Sets of torshear type high strength bolt hexagon nut and plain washer for steel structuresGB/T 3632-1995 | 代替GB3632-83∙∙螺栓或螺钉和平垫圈组合件Bolt or screw and washer assemblies with plain washers GB/T 9074.1-2002 | 代替GB/T 9074.1、9074.14-1988∙∙十字槽头螺钉和外锯齿锁紧垫圈组合件Cross recessed pan head screw and serrated lock washer external teeth assembliesGB/T 9074.2-88 | UDC 621.882∙∙十字槽盘头螺钉和弹簧垫圈组合件Cross recessed pan head screw and single coll spring lock washer assembliesGB/T 9074.3-88 | UDC 621.882∙∙十字槽盘头螺钉、弹簧垫圈和平垫圈组合件Cross recessed pan head screw, single coil spring lock washer assembliesGB/T 9074.4-88 | UDC 621.882∙十字槽小盘头螺钉和平垫圈组合件Cross recessed small pan head screw and small plain washer assembliesGB/T 9074.5-88 | UDC 621.882∙∙十字槽小盘头螺钉和大垫圈组合件Cross recessed small pan head screw and big plain washer assembliesGB/T 9074.6-88 | UDC 621.882∙∙十字槽小盘头螺钉和弹簧垫圈组合件Cross recessed small pan head screw and single coil spring lock washer assembliesGB/T 9074.7-88 | UDC 621.882∙十字槽小盘头螺钉、弹簧垫圈和平垫圈组合件Cross recessed small pan head screw, single coil spring lock washer and plain washer assembliesGB/T 9074.8-88 | UDC 621.882∙十字槽沉头螺钉和锥形锁紧垫圈组合件Cross recessed countersunk head screw and countersunk serrated external toothed lock washer assembliesGB/T 9074.9-88 | UDC 621.882∙∙十字槽凹穴六角头螺栓和平垫圈组合件Cross recessed hexagon bolt with indentation and plain washer assembliesGB/T 9074.11-88 | UDC 621.882∙六角头螺栓和弹簧垫圈组合件Hexagon head bolt and single coil spring lock washer assemblies GB/T 9074.15-88 | UDC 621.882∙六角头螺栓和外锯齿锁紧垫圈组合件Hexagon head bolt and serrated lock washer external teeth assembliesGB/T 9074.16-88 | UDC 621.882∙∙钢结构用高强度大六角头螺栓High strength bolts with large hexagon head for steel structures GB/T 1228-91 | 代替GB1228-84∙钢结构用高强度大六角头螺母High strength large hexagon nuts for steel structures GB/T 1229-91 | 代替GB1229-84∙∙钢结构用高强度垫圈High strength plain washers for steel structuresGB/T 1230-91 | 代替GB1230-84.。
螺钉规格标准——GB标准
螺钉规格标准——GB标准【发布时间：2006-08-24 08:48:24 浏览次数：1677 】规格标准——GB标准开槽圆柱头螺钉GB /T 65-2000 开槽盘头螺钉GB /T 67-2000 开槽沉头螺钉GB /T 68-2000 开槽半沉头螺钉GB /T 69-2000 内六角圆柱头螺钉GB /T 70.1-2000 内六角平圆头螺钉GB /T 70.2-2000 内六角沉头螺钉GB /T 70.3-2000 开槽锥端紧定螺钉GB 71-85 开槽锥端定位螺钉GB 72-88 开槽平端紧定螺钉GB 73-85 开槽凹端紧定螺钉GB 74-85 开槽长圆柱端紧定螺钉GB 75-85 内六角平端紧定螺钉GB /T 77-2000 内六角锥端紧定螺钉GB /T 78-2000 内六角圆柱端紧定螺钉GB /T 79-2000 内六角凹端紧定螺钉GB /T 80-2000 方头长圆柱球面端紧定螺钉GB 83-88 方头凹端紧定螺钉GB 84-88 方头长圆柱端紧定螺钉GB 85-88 方头短圆柱锥端紧定螺钉GB 86-88 十字槽盘头螺钉GB /T 818-2000 六角头不脱出螺钉GB 838-88 滚花头不脱出螺钉GB 839-88 塑料滚花头螺钉GB 840-88 开槽球面圆柱头轴位螺钉GB 946-88 开槽球面大圆柱头螺钉GB 947-88 开槽沉头不脱出螺钉GB 948-88 开槽半沉头不脱出螺钉GB 949-88 内六角花形盘头螺钉GB 2672-86 内六角花形沉头螺钉GB 2673-86 内六角花形半沉头螺钉GB 2674-86 内六角圆柱头轴肩螺钉GB 5281-85 内六角花形圆柱头螺钉-4.8级GB 6190-86 内六角花形圆柱头螺钉-8.8和10.9级GB 6191-86 精密机械用紧固件十字槽螺钉GB /T 13806.1-92 十字槽半沉头螺钉GB /T 820-2000 方头平端紧定螺钉GB 821-88 十字槽圆柱头螺钉GB /T 822-2000 十字槽小盘头螺钉GB 823-88 吊环螺钉GB 825-88 开槽盘头定位螺钉GB 828-88 开槽圆柱端定位螺钉GB 829-88 开槽圆柱头轴位螺钉GB 830-88 开槽无头轴位螺钉GB 831-88 开槽带孔球面圆柱头螺钉GB 832-88 开槽大圆柱头螺钉GB 833-88 滚花高头螺钉GB 834-88 滚花平头螺钉GB 835-88滚花小头螺钉GB 836-88。
GBT818-2000十字槽盘头螺钉
GBT818-2000十字槽盘头螺钉十字槽盘头螺钉GB/T818-2000发布时间：2012-3-6 17:27:58 点击次数：6675次1.本标准规定了螺纹规格为M1.6-M10,性能等级为1.8,A-50,A2-70,CU2,CU3和AL4,H型和Z 型十字槽,产品等级为A级的十字槽盘头螺钉.如需其他技术要求,应从现行标准(如GB/T196, GB/T3106,GB/T3098.1,GB/T3098.6和GB/T3 098.10)中选择2.引用标准下列标准所包含的条文,通过在本标准中引用而构成为本标准的条文,本标准出版时,所示版本均为有效.所有标准都会被修订,使用本标准的各方应探计使用下列标准最新版本的可能性.GB/T90-1985紧固件验收检查,标志与包装GB/T196-1981普通螺纹基本尺寸(直径1-600 mm)GB/T197-1981普通螺纹公差与配合(直径1-35 5mm)GB/T944.1-1985螺钉用十字槽GB/T1237-2000紧固件标记方法GB/T3098.1-2000紧固件机械性能螺栓,螺钉和螺柱GB/T3098.6-2000紧固件机械性能,不锈钢螺栓,螺钉和螺柱GB/T3098.10-1993紧固件机械性能有色金属制造的螺栓,螺钉,螺柱和螺母GB/T3103.1-1982紧固件公差螺栓,螺钉和螺母GB/T3106-1982螺栓,螺钉和螺柱的公称长度和普通螺栓的螺纹长度GB/T5267-1985螺纹紧固件电镀层GB/T5276-1985紧固件螺栓,螺钉,螺柱和螺母尺寸代号和标注GB/T5779.1-2000紧固件表面缺陷螺栓,螺钉和螺柱,一般要求GB/T16938-1997紧固件螺栓,螺钉.螺柱和螺母通用技术条件3.尺寸规格(如图)注:尺寸代号和标注符合GB/T5276无螺纹部分杆径约等于螺纹中径或通俗读物等于螺纹大径.4.技术条件和引用标准(如图)5.标记标记方法按GB/T1237规定标记示例:螺纹规格D=M5,公称长度L=20mm,性能等级为4.8级;H型十字槽,不经表面处理的A级十字槽盘头螺钉的标记:螺钉GB/T818 MX20。
T十字槽盘头螺钉完整版
T十字槽盘头螺钉 HEN system office room 【HEN16H-HENS2AHENS8Q8-HENH1688】十字槽盘头螺钉GB/T818-2000发布时间：2012-3-6 17:27:58 点击次数：6675次1.本标准规定了螺纹规格为,性能等级为,A-50,A2-70,CU2,CU3和AL4,H型和Z型十字槽,产品等级为A级的十字槽盘头螺钉.如需其他技术要求,应从现行标准(如GB/T196,GB/T3106,GB/,GB/和GB/中选择2.引用标准下列标准所包含的条文,通过在本标准中引用而构成为本标准的条文,本标准出版时,所示版本均为有效.所有标准都会被修订,使用本标准的各方应探计使用下列标准最新版本的可能性.GB/T90-1985紧固件验收检查,标志与包装GB/T196-1981普通螺纹基本尺寸(直径1-600mm)GB/T197-1981普通螺纹公差与配合(直径1-355mm)GB/螺钉用十字槽GB/T1237-2000紧固件标记方法GB/紧固件机械性能螺栓,螺钉和螺柱GB/紧固件机械性能,不锈钢螺栓,螺钉和螺柱GB/紧固件机械性能? 有色金属制造的螺栓,螺钉,螺柱和螺母GB/紧固件公差螺栓,螺钉和螺母GB/T3106-1982螺栓,螺钉和螺柱的公称长度和普通螺栓的螺纹长度GB/T5267-1985螺纹紧固件电镀层GB/T5276-1985紧固件螺栓,螺钉,螺柱和螺母尺寸代号和标注GB/紧固件表面缺陷螺栓,螺钉和螺柱,一般要求GB/T16938-1997紧固件螺栓,螺钉.螺柱和螺母通用技术条件3.尺寸规格(如图)注:尺寸代号和标注符合GB/T5276无螺纹部分杆径约等于螺纹中径或通俗读物等于螺纹大径.4.技术条件和引用标准(如图)5.标记标记方法按GB/T1237规定标记示例:螺纹规格D=M5,公称长度L=20mm,性能等级为级;H型十字槽,不经表面处理的A级十字槽盘头螺钉的标记:螺钉GB/T818 MX20。
螺钉规格标准——GB标准
螺钉规格标准——GB标准【大中小发布时间：2006-08-24 08:48:24 浏览次数：1677 】规格标准——GB标准开槽圆柱头螺钉GB /T 65-2000开槽盘头螺钉GB /T 67-2000开槽沉头螺钉GB /T 68-2000开槽半沉头螺钉GB /T 69-2000内六角圆柱头螺钉GB /T 70.1-2000内六角平圆头螺钉GB /T 70.2-2000内六角沉头螺钉GB /T 70.3-2000开槽锥端紧定螺钉GB 71-85开槽锥端定位螺钉GB 72-88开槽平端紧定螺钉GB 73-85开槽凹端紧定螺钉GB 74-85开槽长圆柱端紧定螺钉GB 75-85内六角平端紧定螺钉GB /T 77-2000内六角锥端紧定螺钉GB /T 78-2000内六角圆柱端紧定螺钉GB /T 79-2000内六角凹端紧定螺钉GB /T 80-2000方头长圆柱球面端紧定螺钉GB 83-88方头凹端紧定螺钉GB 84-88方头长圆柱端紧定螺钉GB 85-88方头短圆柱锥端紧定螺钉GB 86-88十字槽盘头螺钉GB /T 818-2000六角头不脱出螺钉GB 838-88滚花头不脱出螺钉GB 839-88塑料滚花头螺钉GB 840-88开槽球面圆柱头轴位螺钉GB 946-88开槽球面大圆柱头螺钉GB 947-88开槽沉头不脱出螺钉GB 948-88开槽半沉头不脱出螺钉GB 949-88内六角花形盘头螺钉GB 2672-86内六角花形沉头螺钉GB 2673-86内六角花形半沉头螺钉GB 2674-86内六角圆柱头轴肩螺钉GB 5281-85内六角花形圆柱头螺钉-4.8级GB 6190-86内六角花形圆柱头螺钉-8.8和10.9级GB 6191-86 精密机械用紧固件十字槽螺钉GB /T 13806.1-92 十字槽半沉头螺钉GB /T 820-2000方头平端紧定螺钉GB 821-88十字槽圆柱头螺钉GB /T 822-2000十字槽小盘头螺钉GB 823-88吊环螺钉GB 825-88开槽盘头定位螺钉GB 828-88开槽圆柱端定位螺钉GB 829-88开槽圆柱头轴位螺钉GB 830-88开槽无头轴位螺钉GB 831-88开槽带孔球面圆柱头螺钉GB 832-88开槽大圆柱头螺钉GB 833-88滚花高头螺钉GB 834-88滚花平头螺钉GB 835-88滚花小头螺钉GB 836-88。
标准件手册
(11A)标准件(11B)标准件说明本《标准件手册》为《标准手册》的一个重要组成部分。
目前，标准件清单尚不完善，我们会不懈努力，使之处于不断完善之中，包括优选清单。
希望工程师们在以后的设计中尽可能选用清单中已有的标准件，特别是已注明为优选的标准件。
对采用新的标准件或不是优选的标准件标准化中心将会进行严格审查，并给出建议。
本《标准件手册》为动态文件（包括目录），将会有专人进行维护，并定期更新发布，同时所有文件均有电子文档，准确的信息以电子文档为准，可随时向标准化中心（或各部门标准化专员）查询。
标准化中心2002年2月（11C）目录(11) 标准件总清单 (4)(1101) 螺钉类清单 (4)(110101) 十字槽盘头螺钉清单 (4)(110102) 十字槽盘头自攻螺钉清单 (4)(110103) 十字槽沉头自攻螺钉清单 (6)(110104) 圆头类螺钉清单 (6)(110105) 六角类螺钉清单 (7)(110106) 非标类及其他螺钉清单 .......................................... 错误！未定义书签。
(1102) 螺栓类清单（压缩机安装螺钉除外）................................ 错误！未定义书签。
(1103) 螺母类清单 (7)(1104) 垫圈类清单 (8)(1105) 其它类标准件清单 (9)(1106) 常用标准件优选表 (9)(11)标准件总清单(1101)螺钉类清单(110101)十字槽盘头螺钉清单(110102)十字槽盘头自攻螺钉清单(110103)十字槽沉头自攻螺钉清单(110104)圆头类螺钉清单(110105)六角类螺钉清单(1102)螺母类清单(1103)垫圈类清单(1104)其它类标准件清单(1105)常用标准件优选表。
紧固件GB标准
紧固件常用GB标准•(ISO 7380-1997) 内六角平圆头螺钉 GB/T 70.2-2000•(ISO 4762-1997)(GB 70-1985) 内六角圆柱头螺钉 GB/T 70.1-2000 •十字槽盘头螺钉 818-85 GB/T 818-2000•六角头螺栓全螺纹 GB/T 5783-2000•1型六角螺母 GB/T 6170-2000•六角薄螺母 GB/T 6172.1-2000•盖形螺母 GB/T 923-88•标准型弹簧垫圈 GB/T 93-87•内六角沉头螺钉 GB/T 70.3-2000•内六角凹端紧定螺钉 GB/T 80-2000•平垫圈 A级 GB/T 97.1-2002•钢结构用高强度垫圈 GB/T 1230-91•钢结构用高强度大六角头螺母 GB/T 1229-91•钢结构用高强度大六角头螺栓 GB/T 1228-91•大半圆头方颈螺栓 C级 GB/T 14-1998•半圆头方颈螺栓 GB/T 12-88•十字槽小盘头螺钉 GB/T 823-88•等长双头螺柱 B级 GB/T 901-88•十字槽沉头螺钉第1部分：钢4.8级 GB/T 819.1-2000•开口型扁圆头抽芯铆钉 GB/T 12618-90•圆柱销不淬硬钢和奥氏体不锈钢 GB/T 119.1-2000•十字槽沉头自攻螺钉 GB/T 846-85•十字槽盘头自攻螺钉 GB/T 845-85•小垫圈 A级 GB/T 848-2002•大垫圈 A级 GB/T 96.1-2002•六角头螺栓 GB/T 5782-20001. 螺栓•六角头螺栓细牙Hexagon head bolts with fine pitch threadGB/T 5785-2000 | 代替GB/T 5785-1986•六角头螺栓细牙全螺纹Hexagon head bolts with fine pitch thread-Full thread GB/T 5786-2000 | 代替GB/T 5786-1986•六角法兰面螺栓-加大系列-B级Hexagon flange bolts-Heavy series-product grade B GB/T 5789-86 | UDC 621.882.6•六角法兰面螺栓-加大系列-细杆-B级Hexagon flange bolts-Heavy series-product grade B GB/T 5790-86 | UDC 621.882.6•六角法兰面螺栓小系列Hexagon flange bolts-Small seriesGB/T 16674-1996 | 代替GB/T 5787、5788-1986•钢网架螺栓球节点用高强度螺栓High strength bolts for joints of space grid structures GB/T 16939-1997•扩口式管接头空心螺栓Flared type tube fittings Inverted flare bolts GB 5650•GB/T 3098.13-1996 紧固件机械性能螺栓与螺钉GB/T 3098.13-1996 紧固件机械性能螺栓与螺钉3098•GB18230.2-2000 栓接结构用大六角螺栓短螺纹GB18230.2-2000 栓接结构用大六角螺栓短螺纹GB18230.2-2000•U型螺栓U-boltsJB/ZQ 4321-97 | 代替JB/ZQ 4321-86•大半圆头带榫螺栓Cup head nib bolts with large headGB/T 15-88 | UDC 621.882.6 | 代替GB15-76•六角头铰制孔用螺栓Hexagon fit bolts-product grade A and BGB/T 27-88 | UDC 621.882.6 | 代替GB27-76•六角头螺杆带孔铰制孔用螺栓Hexagon fit bolts with split pin hole on shank-product gradeA and BGB/T 28-88 | UDC 621.882.6 | 代替GB28-76•六角头头部带槽螺栓 A 和 B 级Hexagon bolts with slot on head -product A and B GB/T 29.1-88 | UDC 621.882.6 | 代替GB29-76•十字槽凹穴六角头螺栓Cross recessed hexagon bolts with indentation GB/T 29.2-88 | UDC 621.882.6 | 代替GB29-76•下方头螺栓 B级Square head bolts with small head-praduct grade BGB/T 35-88 | UDC 621.882.6 | 代替GB35-76•T 形槽用螺栓Bolts for T-SlotGB/T 37-88 | UDC 621.882.6 | 代替GB37-76•加强半圆头方颈螺栓Strengthened cup head square neck boltsGB/T 794-93 | 代替GB794-67•六角头螺杆带孔螺栓Hexagon bolts with split pin hole on shank-product grade A and B GB/T 31.1-88 | UDC 621.882.6 | 代替GB31、23、24-76•六角头螺杆带孔螺栓细杆 B级Hexagon bolts with split pin hole on shank-Reduced shank-product grade BGB/T 31.2-88 | UDC 621.882.6 | 代替GB31、23、24-76•六角头螺杆带孔螺栓细牙 A和B级Hexagon bolts with split pin hole on shank-Fine pitch thread-product grade A and BGB/T 31.3-88 | UDC 621.882.6 | 代替GB31、23、24-76•方头螺栓 C级Square head bolts-Product grade CGB/T 8-88 | UDC 621.882.6 | 代替GB8-76•沉头方颈螺栓Flat countersunk square neck boltsGB/T 10-88 | UDC 621.882.6 | 代替GB10-76•沉头带榫螺拴Flat countersunk nib boltsGB/T 11-88 | UDC 621.882.6 | 代替GB11-76•半圆头带榫螺栓Cup head nid boltsGB/T 13-88 | UDC 621.882.6 | 代替GB13-76•六角头头部带孔螺栓 A 和 B级Hexagon bolts with wire holes on head-product grade A and BGB/T 32.1-88 | UDC 621.882.6 | 代替GB32、25、26-76•六角头头部带孔螺栓细杆 B级Hexagon bolts with wire holes on head-Reduced shank-product grade BGB/T 32.2-88 | UDC 621.882.6 | 代替GB32、25、26-76•六角头头部带孔螺栓细牙 A 和 B 级Hexagon bolts with wire holes on head-Fine pitch thread-product grade A and BGB/T 32.3-88 | UDC 621.882.6 | 代替GB32、25、26-76•活节螺栓Eye boltsGB/T 798-88 | UDC 621.882.6 | 代替GB798-76•地脚螺栓Eyelet boltsGB/T 799-88 | UDC 621.882.6 | 代替GB799-76•沉头双榫螺Flat countersunk double nib boltsGB/T 800-88 | UDC 621.882.6 | 代替GB800-77•小半圆头低方颈螺栓 B级Cup head square neck bolts with small head and short neck-product grade BGB/T 801-1998 | 代替GB801-88•六角头螺栓 C级Hexagon head bolts-product grade CGB/T 5780-2000 | 代替GB/T 5780-1986•六角头螺栓全螺纹 C级Hexagon head bolts-Full thread-product grade C GB/T 5781-2000 | 代替GB/T 5781-1986•六角头螺栓-细杆-B级Hexagon head bolts-Reduced shank -Product grade B GB/T 5784-86 | UDC 621.882.6 | 代替GB30、21-76•六角头螺栓 Hexagon head boltsGB/T 5782-2000 | 代替GB/T 5782-1986•六角头螺栓全螺纹 Hexagon head bolts-Full threadGB/T 5783-2000 | 代替GB/T 5783-1986•大半圆头方颈螺栓 C级Cup head square neck bolts with large head-Product grade C GB/T 14-1998 | 代替GB14-88•半圆头方颈螺栓Cup head square neck boltsGB/T 12-88 | UDC 621.882.6 | 代替GB12-762.螺钉•方头长圆柱球面端紧定螺钉Square set screws with long dog point and rounded end GB/T 83-88 | UDC 621.882.2 | 代替GB83-76•开槽圆柱头轴位螺钉Slotted cheese head screws with shoulderGB/T 830-88 | UDC 621.882.2 | 代替GB830-76•开槽无头轴位螺钉Slotted shoulder screwsGB/T 831-88 | UDC 621.882.2 | 代替GB831-76•开槽带孔球面圆柱头螺钉Slotted capstan screwsGB/T 832-88 | UDC 621.882.2 | 代替GB832-76•开槽圆柱头螺钉Slotted cheese head screwsGB/T 65-2000 | 代替GB/T 65-1985•开槽盘头螺钉Slotted pan head screwsGB/T 67-2000 | 代替GB/T 67-1985•开槽沉头螺钉Slotted countersunk flat head screws (common head style) GB/T 68-2000 | 代替GB/T 68-1985•开槽半沉头螺钉Countersunk slotted raised head screws (common head style) GB/T 69-2000 | 代替GB/T 69-1985•开槽锥端紧定螺钉Slotted set screws with cone pointGB/T 71-85 | UDC 621.882.219 | 代替GB71-76•开槽锥端定位螺钉Slotted setscrews with cone pointGB/T 72-88 | UDC 621.882.2 | 代替GB72-76•开槽平端紧定螺钉Slotted set screws with flat pointGB/T 73-85 | UDC 621.882.219.4 | 代替GB73-76•滚花高头螺钉Knurled thumb screwsGB/T 834-88 | UDC 621.882.2 | 代替GB834-76•滚花平头螺钉Knurled screwsGB/T 835-88 | UDC 621.882.2 | 代替GB835-76•滚花小头螺钉Knurled screws with small headGB/T 836-88 | UDC 621.882.2 | 代替GB836-76•开槽盘头不脱出螺钉Slotted pan head screws with waisted shankGB/T 837-88 | UDC 621.882.2 | 代替GB837-76•方头短圆柱锥端紧定螺钉Square set screws with short dog point and cone end GB/T 86-88 | UDC 621.882.2 | 代替GB86-76•开槽凹端紧定螺钉Slotted set screws with cup pointGB/T 74-85 | UDC 621.882.219.4.092.6 | 代替GB74-76•方头长圆柱端紧定螺钉Square set screws with long dog pointGB/T 85-88 | UDC 621.882.2 | 代替GB85-76•十字槽半沉头螺钉Countersunk raised head screws (common head style) with cross recess GB/T 820-2000 | 代替GB/T 820-1985•开槽圆柱端定位螺钉Slotted setscrews with dog pointGB/T 829-88 | UDC 621.882.2 | 代替GB829-76•开槽大圆柱头螺钉Slotted large cheese head screwsGB/T 833-88 | UDC 621.882.2 | 代替GB833-76•六角头不脱出螺钉Hexagon screws with waisted shankGB/T 838-88 | UDC 621.882.2 | 代替GB838-76•十字槽沉头螺钉第2部分：钢8.8、不锈钢A2-70和有色金属CU2或CU3 Cross recessed countersunk flat head screws (common head style)-Grade A-Part 2:Steel of property class 8.8, stainless and non-ferrous metalsGB/T 819.2-1997•方头平端紧定螺钉Square set screws with chamfered endGB/T 821-88 | UDC 621.882.2 | 代替GB821-76•十字槽圆柱头螺钉Cheese head screws with cross recessGB/T 822-2000 | 代替GB/T 822-1988•吊环螺钉 EyeboltsGB/T 825-88 | UDC 621.882 | 代替GB825-76•精密机械用紧固件十字槽螺钉Fasteners for mechanics-Cross recessed screws GB/T 13806.1-92•方头凹端紧定螺钉Square set screws with cup pointGB/T 84-88 | UDC 621.882.2 | 代替GB84-76•开槽盘头定位螺钉Slotted pan head set setscrews with dog pointGB/T 828-88 | UDC 621.882.2 | 代替GB828-76•滚花头不脱出螺钉Knurled thumb screws with waisted shankGB/T 839-88 | UDC 621.882.2 | 代替GB839-76•塑料滚花头螺钉Plastic diamond knurlhead screwsGB/T 840-88 | UDC 621.882.2 | 代替GB840-79•开槽球面圆柱头轴位螺钉Slotted raised head with shoulderGB/T 946-88 | UDC 621.882.2 | 代替GB946-76•开槽球面大圆柱头螺钉Slotted large raised cheese head screwsGB/T 947-88 | UDC 621.882.2 | 代替GB947-76•开槽沉头不脱出螺钉Slotted countersunk head screws with waisted shank GB/T 948-88 | UDC 621.882.2 | 代替GB948-76•开槽半沉头不脱出螺钉Slotted raised countersunk head screws with waisted shank GB/T 949-88 | UDC 621.882.2 | 代替GB949-76•开槽长圆柱端紧定螺钉Slotted set screws with long dog pointGB/T 75-85 | UDC 621.882.219.4.092.5 | 代替GB75-76•十字槽小盘头螺钉 Cross recessed small pan head screwsGB/T 823-88 | UDC 621.882.2 | 代替GB823-76•十字槽盘头螺钉 818-85 Pan head screws with cross recessGB/T 818-2000 | 代替GB/T 818-1985•十字槽沉头螺钉第1部分：钢4.8级Countersunk flat head screws (common head style)with cross recess-Part 1:Steel of property class 4.8GB/T 819.1-2000 | 代替GB/T 819-1985•GB70.2-2000(ISO 7380-1997) 内六角平圆头螺钉Hexagon socket flat head screws GB70.2-2000(ISO 7380-1997 | 代替GB70.2-2000(ISO 7380-19973. 内六角螺钉•(ISO 4762-1997)(GB 70-1985) 内六角圆柱头螺钉Hexagon socket head cap screws GB/T 70.1-2000 | 代替GB/T 70-1985•(ISO 7380-1997)内六角平圆头螺钉Hexagon socket button head screwsGB/T 70.2-2000•内六角凹端紧定螺钉Hexagon socket set screws with cup pointGB/T 80-2000 | 代替GB/T 80-1985•内六角沉头螺钉Hexagon socket countersunk head screwsGB/T 70.3-2000•内六角花形半沉头螺钉Hexagon lobular socket raised countersunk head screws GB/T 2674-86 | UDC 621.882.2 | 代替GB2674-81•内六角花形沉头螺钉Hexagon lobular socket countersunk head screwsGB/T 2673-86 | UDC 621.882.2 | 代替GB2673-81•内六角花形盘头螺钉Hexagon lobular socket pan head screwsGB/T 2672-86 | UDC 621.882.2 | 代替GB2672-81•内六角花形圆柱头螺钉-4.8级Hexagon lobular socket head cap screws-property class 4.8 GB/T 6190-86 | UDC 621.882.2 | 代替GB2671-81•内六角花形圆柱头螺钉-8.8和10.9级Hexagon lobular socket head cap screws-property class8.8 and 10.9GB/T 6191-86 | UDC 621.882.2 | 代替GB2671-81•内六角平端紧定螺钉Hexagon socket set screws with flat pointGB/T 77-2000 | 代替GB/T 77-1985•内六角圆柱端紧定螺钉Hexagon socket set screws with dog pointGB/T 79-2000 | 代替GB/T 79-1985•内六角圆柱头轴肩螺钉Hexagon socket head shoulder screwsGB/T 5281-85 | UDC 621.882.215.6•内六角锥端紧定螺钉Hexagon socket set screws with cone pointGB/T 78-2000 | 代替GB/T 78-19854. 自攻螺钉•十字槽半沉头自攻锁紧螺钉Cross recessed raised countersunk head thread forming screws GB/T 6562-86 | UDC 621.882•六角头自攻锁紧螺钉Hexagon head thread forming screwsGB/T 6563-86 | UDC 621.882•内六角花形圆柱头自攻锁紧螺钉Hexagon lobular socket thread forming screws GB/T 6564-86 | UDC 621.882•十字槽半沉头自攻螺钉Cross recessed raised countersunk head tapping screws GB/T 847-85 | UDC 621.882.216.5.082.8 | 代替GB847-76•开槽盘头自攻螺钉 Slotted pan head tapping screwsGB/T 5282-85 | UDC 621.882.215.082.8•开槽沉头自攻螺钉Slotted countersunkhead tapping screwsGB/T 5283-85 | UDC 621.882.215.082.8•开槽半沉头自攻螺钉Slotted raised countersunkhead tapping screwsGB/T 5284-85 | UDC 621.882.215.082.8•六角头自攻螺钉Hexagon head tapping screwsGB/T 5285-85 | UDC 621.882.215.082.8•十字槽盘头自攻锁紧螺钉Cross recessed pan head thread forming screws GB/T 6560-86 | UDC 621.882•十字槽沉头自攻锁紧螺钉Cross recessed countersunk head thread forming screws GB/T 6561-86 | UDC 621.882•十字槽头凹穴六角头自攻螺钉Cross recessed hexagon head tapping screws with indentation GB/T 9456-88 | UDC 621.882.2•精密机械用紧固件十字槽自攻螺钉刮削端Fasteners for fine mechanics-Cross recessed tapping screws-Scrape pointGB/T 13806.2-92•墙板自攻螺钉Dry wall screwsGB/T 14210-93•十字槽盘头自钻自攻螺钉Cross recessed pan head drilling screws with tapping screw thread GB/T 15856.1-2002 | 代替GB/T 15856.1-1995•十字槽沉头自钻自攻螺钉Cross recessed countersunk head drilling screws with tapping screw threadGB/T 15856.2-2002 | 代替GB/T 15856.2-1995•十字槽半沉头自钻自攻螺钉Cross recessed raised countersunk head drilling screws with tapping screw threadGB/T 15856.3-2002 | 代替GB/T 15856.3-1995•六角法兰面自钻自攻螺钉Hexagon flange drilling screws with tapping screw thread GB/T 15856.4-2002 | 代替GB/T 15856.4-1995•六角凸缘自钻自攻螺钉Hexagon washer head drilling screws with tapping screw thread GB/T 15856.5-2002•六角凸缘自攻螺钉Hexzgon head tapping screws with collarGB/T 16824.1-1997•六角法兰面自攻螺钉Hexagon flange head tapping screwsGB/T 16824.2-1997•十字槽盘头自攻螺钉 Cross recessed pan head tapping screwsGB/T 845-85 | UDC 621.882.216.5.082.8 | 代替GB845-76•十字槽沉头自攻螺钉 Cross recessed countersunk head tapping screws GB/T 846-85 | UDC 621.882.216.5.082.8 | 代替GB846-765.木螺钉•开槽半沉头木螺钉Slotted raised countersunk head wood screwsGB/T 101-86 | UDC 621.882.2 | 代替GB101-76•开槽沉头木螺钉Slotted countersunk head wood screwsGB/T 100-86 | UDC 621.882.2 | 代替GB100-76•开槽圆头木螺钉Slotted round head wood screwsGB/T 99-86 | UDC 621.882.2 | 代替GB99-76•六角头木螺钉Hexagon head wood screwsGB/T 102-86 | UDC 621.882.2 | 代替GB102-76•十字槽半沉头木螺钉Cross recessed raised head countersunk head wood screws GB/T 952-86 | UDC 621.882.2 | 代替GB952-76•十字槽沉头木螺钉Cross recessed countersunk head wood screwsGB/T 951-86 | UDC 621.882.2 | 代替GB951-76•十字槽圆头木螺钉Cross recessed round head wood screws GB/T 950-86 | UDC 621.882.2 | 代替GB950-766.螺杆和螺柱•储能焊用焊接螺柱Weld studs for capacitor discharge welding GB/T 902.3-89 | 代替GB902-76•等长双头螺柱 B级Double end studs(clamping type) -Product grade B GB/T 901-88 | UDC 621.882 | 代替GB901-76•等长双头螺柱 C级Double end studs(clamping type)-product grade C GB/T 953-88 | UDC 621.882 | 代替GB953-76•机动弧焊用焊接螺柱Weld studs for arc weldingGB/T 902.2-89 | 代替GB902-76•螺杆Threaded rodsGB/T 15389-94•手工焊用焊接螺柱Weld studs for manual weldingGB/T 902.1-89 | 代替GB902-76•双头螺柱 bm=1.25d Double end studs-bm=1.25dGB/T 898-88 | UDC 621.882 | 代替GB898-76•双头螺柱 bm=1.5d Double end studs-bm=1.5dGB/T 899-88 | UDC 621.882 | 代替GB899-76•双头螺柱 bm=1d Double end studs-bm=1dGB/T 897-88 | UDC 621.882 | 代替GB897-76•双头螺柱 bm=2d Double end studs--bm=2dGB/T 900-88 | UDC 621.882 | 代替GB900-76•等长双头螺栓Double end studs•动负荷预应力螺柱Dynamic load prestressed studs•阶端双头螺柱Order end double end studs•双头螺栓Double end studs•双头螺柱Double end studs•双头螺柱Double end studs•双头螺柱b1=1.25d Double end studs7.铆钉•平头铆钉Flat head rivetsGB/T 109-86 | UDC 621.884 | 代替GB109-76•标牌铆钉Rivets for name plateGB/T 827-86 | UDC 621.884 | 代替GB827-76•半圆头铆钉(粗制) Round head rivets-BlackGB/T 863.1-86 | UDC 621.884 | 代替GB863-76•小半圆头铆钉(粗制) Round head rivets with small head-Black GB/T 863.2-86 | UDC 621.884•平锥头铆钉(粗制) Cone head rivets-BlackGB/T 864-86 | UDC 621.884 | 代替GB864-76•沉头铆钉(粗制) Countersunk head rivets-BlackGB/T 865-86 | UDC 621.884 | 代替GB865-86•半沉头铆钉(粗制) Oval countersunk head rivets-Black GB/T 866-86 | UDC 621.884 | 代替GB866-76•半圆头铆钉Round head rivetsGB/T 867-86 | UDC 621.884 | 代替GB867-76•平锥头铆钉Cone head rivetsGB/T 868-86 | UDC 621.884 | 代替GB868-76•沉头铆钉Countersunk head rivetsGB/T 869-86 | UDC 621.884 | 代替GB869-76•扁圆头击芯铆钉Flat round head drive rivetsGB/T 15855.1-1995•半沉头铆钉Oval countersunk head rivetsGB/T 870-86 | UDC 621.884 | 代替GB870-76•扁圆头铆钉Flat round head rivetsGB/T 871-86 | UDC 621.884 | 代替GB871-76•扁平头铆钉Thin head rivetsGB/T 872-86 | UDC 621.884 | 代替GB872-76•扁圆头半空心铆钉Oval head semi-tubular rivetsGB/T 873-86 | UDC 621.884 | 代替GB873-76•120°沉头半空心铆钉120 degree countersunk head semi-tubular rivets GB/T 874-86 | UDC 621.884 | 代替GB874-76•扁平头半空心铆钉Thin head semi-tubular rivetsGB/T 875-86 | UDC 621.884 | 代替GB875-76•空心铆钉Tubular rivetsGB/T 876-86 | UDC 621.884 | 代替GB876-76•120°沉头铆钉120 degree countersunk head rivetsGB/T 954-86 | UDC 621.884 | 代替GB954-76•管状铆钉Pipe type rivetsGB/T 975-86 | UDC 621.884 | 代替GB975-76•大扁圆头铆钉Truss head rivetsGB/T 1011-86 | UDC 621.884 | 代替GB1011-76•120°半沉头铆钉120 degree oval countersunk rivetsGB/T 1012-86 | UDC 621.884 | 代替GB1012-76•平锥头半空心铆钉Cone head semi-tubler rivetsGB/T 1013-86 | UDC 621.884 | 代替GB1013-76•大扁圆头半空心铆钉Truss head semi-tublar rivetsGB/T 1014-86 | UDC 621.884 | 代替GB1014-76•沉头半空心铆钉Countersunk head semi-tublar rivetsGB/T 1015-86 | UDC 621.884 | 代替GB1015-76•无头铆钉Headless rivetsGB/T 1016-86 | UDC 621.884 | 代替GB1016-76•封闭型扁圆头抽芯铆钉Mushroom head break mandrel closed end blind rivets GB/T 12615-90•封闭型沉头抽芯铆钉120 deg flush head break mandrel closed end blind rivets GB/T 12616-90•开口型沉头抽芯铆钉120 deg flush head break mandrel blind rivets GB/T 12617-90•沉头击芯铆钉Countersunk head drive rivetsGB/T 15855.2-1995•开口型扁圆头抽芯铆钉Mushroom head break mandrel blind rivets GB/T 12618-908.螺母•滚花高螺母Knurled nut with collarGB/T 806-88 | UDC 621.882.3 | 代替GB806-76•滚花薄螺母Knurled nutsGB/T 807-88 | UDC 621.882.3 | 代替GB807-76•小六角特扁细牙螺母Small hexagon thin nuts-Fine pitch thread GB/T 808-88 | UDC 621.882.3 | 代替GB808-76•嵌装圆螺母Lnsert round nutsGB/T 809-88 | UDC 621.882.3 | 代替GB809-76•小圆螺母Small round nutsGB/T 810-88 | UDC 621.882.3 | 代替GB810-76•圆螺母Round nutsGB/T 812-88 | UDC 621.882.3 | 代替GB812-76•端面带孔圆螺母Round nuts with drilled holes in one faceGB/T 815-88 | UDC 621.882.3 | 代替GB815-76•侧面带孔圆螺母Round nuts with set pin holes in sideGB/T 816-88 | UDC 621.882.3 | 代替GB816-79•带槽圆螺母Slotted round nutsGB/T 817-88 | UDC 621.882.3 | 代替GB817-76•1型非金属嵌件六角锁紧螺母Prevailing torque type hexagon nuts(with non-metallic insert),style 1GB/T 889.1-2000 | 代替GB/T 889-1986•1型六角开槽螺母细牙 A和B级Hexagon slotted and castle nuts,style 1-fine pitch thread-product grades A and BGB/T 9457-88 | UDC 621.882.3 | 代替GB57、58-76•2型六角开槽螺母细牙 A和B级Hexagon slotted and castle nuts,style 2--Fine pitch thread -Product grades A and BGB/T 9458-88 | UDC 621.882.3•六角开槽薄螺母细牙 A和B级Hexagon thin slotted nuts--Fine pitch thread -Product gradesA and BGB/T 9459-88 | UDC 621.882.3 | 代替GB59、60-76•焊接方螺母Square weld nutsGB/T 13680-92•焊接六角螺母Hexagon weld nutsGB/T 13681-92•平头铆螺母Flat head riveted nutsGB/T 17880.1-1999•沉头铆螺母Countersunk head riveted nutsGB/T 17880.2-1999•小沉头铆螺母Small countersunk head riveted nutsGB/T 17880.3-1999•120°小沉头铆螺母120°Small countersunk head riveted nutsGB/T 17880.4-1999•平头六角铆螺母Flat head hexagon riveted nutsGB/T 17880.5-1999•精密机械用六角螺母Hexagon nuts for fine mechanicsGB/T 18195-2000•1型非金属嵌件六角锁紧螺母细牙Prevailing torque type hexagon nuts(with non-metallic insert),style 1,with fine pitch threadGB/T 889.2-2000•非金属嵌件六角锁紧薄螺母Prevailing torque type hexagon thin nuts(with non-metallic insert)GB/T 6072.2-2000•六角薄螺母细牙Hexagon thin nuts(chamfered) with fine pitch thread GB/T 6173-2000 | 代替GB/T 6173-1986•六角薄螺母无倒角Hexagon thin nuts(unchamfered)GB/T 6174-2000 | 代替GB/T 6174-1986•1型六角螺母细牙Hexagon nuts,style 1,with fine pitch threadGB/T 6171-2000 | 代替GB/T 6171-1986•方螺母 C级Square nuts-product grade CGB/T 39-88 | UDC 621.882.3 | 代替GB39-76•六角螺母 C级Hexagon nuts-product grade CGB/T 41-2000 | 代替GB/T 41-1986•六角厚螺母Hexagon thick nutsGB/T 56-88 | 代替GB56-76•蝶形螺母Wing nutsGB/T 62-88 | UDC 621.882.3 | 代替GB62-76•环形螺母Lifting nutsGB/T 63-88 | UDC 621.882.3 | 代替GB63-76•组合式盖形螺母Acorn nutsGB/T 802-88 | UDC 621.882.3 | 代替GB802-76•球面六角螺母Hexagon nuts with raised faceGB/T 804-88 | UDC 621.882.3 | 代替GB804-76•2型六角螺母Hexagon nuts,style 2GB/T 6175-2000 | 代替GB/T 6175-1986•2型六角螺母细牙Hexagon nuts,style 2,with fine pitch threadGB/T 6176-2000 | 代替GB/T 6176-1986•六角法兰面螺母Hexagon nuts with flangeGB/T 6177.1-2000 | 代替GB/T 6177-1986•六角法兰面螺母细牙Hexagon nuts with flange-fine pitch threadGB/T 6177.2-2000•1型六角开槽螺母-A和B级Hexagon slotted and castle nuts,style 1 -product grades A and BGB/T 6178-86 | UDC 621.882.3 | 代替GB57~58-76•1型六角开槽螺母-C级Hexagon slotted nuts,style 1 -product grade C GB/T 6179-86 | UDC 621.882.3 | 代替GB57~58-76•2型六角开槽螺母-A和B级Hexagon slotted and castle nuts,style 2 -Product grades A and BGB/T 6180-86 | UDC 621.882.3•六角开槽薄螺母-A和B级Hexagon thin slotted nuts-Product grades A and B GB/T 6181-86 | UDC 621.882.3 | 代替GB59~60-76•2型非金属嵌件六角锁紧螺母Prevailing torque type hexagon nuts(with non-metallic insert),style 2GB/T 6182-2000 | 代替GB/T 6182-1986•非金属嵌件六角法兰面锁紧螺母Prevailing torque type hexagon nuts with flange(with non-metallic insert)GB/T 6183.1-2000 | 代替GB/T 6183-1986•非金属嵌件六角法兰面锁紧螺母细牙Prevailing torque type hexagon nuts with flange(with non-metallic insert)with fine pitch threadGB/T 6183.2-2000•1型全金属六角锁紧螺母Prevailing torque type all-metal hexagon nuts,style 1 GB/T 6184-2000 | 代替GB/T 6184-1986•2型全金属六角锁紧螺母Prevailing torque type all-metal hexagon nuts,style 2 GB/T 6185.1-2000 | 代替GB/T 6185-1986•2型全金属六角锁紧螺母细牙Prevailing torque type all-metal hexagon nuts,style 2,with fine pitch threadGB/T 6185.2-2000•2型全金属六角锁紧螺母 9级Prevailing torque type all-metal hexagon nuts,style 2-Property class 9GB/T 6186-2000 | 代替GB/T 6186-1986•全金属六角法兰面锁紧螺母Prevailing torque type all-metal hexagon nuts with flange GB/T 6187.1-2000 | 代替GB/T 6187-1986•全金属六角法兰面锁紧螺母细牙Prevailing torque type all-metal hexagon nuts with flange with fine pitch threadGB/T 6187.2-2000•扣紧螺母Tight nutsGB/T 805-88 | UDC 621.882.3 | 代替GB805-76•六角薄螺母Hexagon thin nuts(chamfered)GB/T 6172.1-2000 | 代替GB/T 6172-1986•1型六角螺母Hexagon nuts,style 1GB/T 6170-2000 | 代替GB/T 6170-1986•盖形螺母Acorn nutsGB/T 923-88 | UDC 621.882.3 | 代替GB923-769.垫圈•工字钢用方斜垫圈Square taper washers for I sectionGB/T 852-88 | UDC 621.882.4 | 代替GB852-76•槽钢用方斜垫圈Square taper washers for slot sectionGB/T 853-88 | UDC 621.882.4 | 代替GB853-76•单耳止动垫圈Tab washers with long tabGB/T 854-88 | UDC 621.882.4 | 代替GB854-76•双耳止动垫圈Tab washers with long tab and wingGB/T 855-88 | UDC 621.882.4 | 代替GB855-76•外舌止动垫圈External tab washersGB/T 856-88 | UDC 621.882.4 | 代替GB856-76•圆螺母用止动垫圈Tab washers for round nutGB/T 858-88 | UDC 621.882.4 | 代替GB858-76•轻型弹簧垫圈Single coil spring lock washers,Light type GB/T 859-87 | UDC 621.882.4 | 代替GB859-76•鞍形弹性垫圈Curved spring washersGB/T 860-87 | UDC 621.882.4 | 代替GB860-76•内齿锁紧垫圈Lock washers internal teethGB/T 861.1-87 | UDC 621.882.4 | 代替GB861-76•内锯齿锁紧垫圈Serrated lock washers internal teethGB/T 861.2-87 | UDC 621.882.4•外齿锁紧垫圈Lock washers external teethGB/T 862.1-87 | UDC 621.882.4 | 代替GB862-76•外锯齿锁紧垫圈Serrated lock washers external teethGB/T 862.2-87 | UDC 621.882.4•波形弹性垫圈Wave spring washersGB/T 955-87 | UDC 621.882.4 | 代替GB955-76•锥形锁紧垫圈Countersunk external toothed lock washers GB/T 956.1-87 | UDC 621.882.4 | 代替GB956-76•锥形锯齿锁紧垫圈Countersunk Serrated external toothed lock washers GB/T 956.2-87 | UDC 621.882.4•特大垫圈 C级Plain washers-Extra large series-Product grade C GB/T 5287-2002 | 代替GB/T 5287-1985•重型弹簧垫圈Single coil spring lock washers,heavy type GB/T 7244-87 | UDC 621.882.4•鞍形弹簧垫圈Curved Single coil spring lock washersGB/T 7245-87 | UDC 621.882.4•波形弹簧垫圈Wave Single coil spring lock washersGB/T 7246-87 | UDC 621.882.4•大垫圈 C级Plain washers-Large series-Product grade C GB/T 96.2-2002 | 代替GB/T 96-1985•平垫圈倒角型 A级Plain washers,chamfered-Product grade AGB/T 97.2-2002 | 代替GB/T 97.2-1985•平垫圈用于螺钉和垫圈组合件Plain washers for screw and washer assemblies GB/T 97.4-2002 | 代替GB/T 9074.24、9074.25-1988•球面垫圈Washers with ball faceGB/T 849-88 | UDC 621.882.4 | 代替GB849-76•锥面垫圈Washers with cone faceGB/T 850-88 | UDC 621.882.4 | 代替GB850-76•开口垫圈Washers with splitGB/T 851-88 | UDC 621.882.4 | 代替GB851-76•平垫圈用于自攻螺钉和垫圈组合件Plain washers for tapping screw and washer assemblies GB/T 97.5-2002 | 代替GB/T 9074.29、9074.30-1988•平垫圈 C级Plain washers-Product grade CGB/T 95-2002 | 代替GB/T 95-1985•销轴用平垫圈Plain washers for clevis pinsGB/T 97.3-2000•平垫圈 A级Plain washers-Product grade AGB/T 97.1-2002 | 代替GB/T 97.1-1985•标准型弹簧垫圈Single coil spring lock washers Normal typeGB/T 93-87 | UDC 621.882.4 | 代替GB93-76•大垫圈 A级Plain washers-Large series-Product grade AGB/T 96.1-2002 | 代替GB/T 96-1985•小垫圈 A级Plain washers-small series-Product grade AGB/T 848-2002 | 代替GB/T 848-198510.组合件和连接副•六角头螺栓、弹簧垫圈和平垫圈组合件Hexagon head bolt,single coil spring lock washer and plain washer assembliesGB/T 9074.17-88 | UDC 621.882•自攻螺钉和平垫圈组合件Tapping screw and washer assemblies with plain washers GB/T 9074.18-2002 | 代替GB/T 9074.18、9074.19、9074、22、9074、23-1988•十字槽凹穴六角头自攻螺钉和平垫圈组合件Cross recessed hexagon head tapping screw with indentation and plain washer assembliesGB/T 9074.20-88 | UDC 621.882•十字槽凹穴六角头自攻螺钉和大垫圈组合件Cross recessed hexagon head tapping sorew with indentation and large plain washer assembliesGB/T 9074.21-88 | UDC 621.882•组合件用弹簧垫圈Single coil spring lock washer for assemblyGB/T 9074.26-88 | UDC 621.882•组合件用外锯齿锁紧垫圈Serrated lock washer external teeth for assembly GB/T 9074.27-88 | UDC 621.882•组合件用锥形锁紧垫圈Lountersunk external toothed lock washer for assembly GB/T 9074.28-88 | UDC 621.882•腰状杆螺柱连接副型式分类Connections with waisted stud-Tape classification GB/T 13807.1-92•腰状杆螺柱连接副螺柱Connections with waisted stud-StudsGB/T 13087.2-92•腰状杆螺柱连接副螺母、受力套管Connections with waisted stud-Nuts,extension sleeves GB/T 13087.3-92•栓接结构用大六角头螺栓螺纹长度按GB/T 3106 C级 8.8和10.9级Hexagon bolts for high-strength structural bolting with large width across flats(thread lengths according to GB/T 3106)-Product grade C-Property classes 8.8 and 10.9GB/T 18230.1-2000•栓接结构用大六角头螺栓短螺纹长度 C级 8.8和 10.9级Hexagon bolts for high-strengthstructural bolting with large width across flats(short thread length)-Product grade C-property classes 8.8 and 10.9GB/T 18230.2-2000•栓接结构用大六角头螺母 B级 8和10级Hexagon nuts for high-strength structural bliting with large width across flats-Product grade B-Property classes 8 and 10GB/T 18230.3-2000•栓接结构用1型大六角螺母 B级 10级Hexagon nuts for structural bolting with large width across flats,style 1-Product grade B-Property class 10GB/T 18230.4-2000•栓接结构用平垫圈淬火并回火Plain washers for high-strength structural bolting hardened and temperedGB/T 18230.5-2000•栓接结构用1型大六角螺母浸热镀锌(加大攻丝尺寸) A和B级 5.6和8级Hexagon nuts for structural bolting,style 1,hot-dip galvanized(oversize tapped)-Product grade A and B-Property classes 5.6 and 8GB/T 18230.6-2000•栓接结构用2型大六角螺母浸热镀锌(加大攻丝尺寸) A级 9级Hexagon nuts for structural bolting,style 2,hot-dip galvanized(oversize tapped)-Product grade A -Property class 9GB/T 18230.7-2000•十字槽半沉头螺钉和锥形锁紧垫圈组合件Cross recessed raised countersunk head screw and countersunk external toothed lock washer assembliesGB/T 9074.10-88 | UDC 621.882•十字槽凹穴六角头螺栓和弹簧垫圈组合件Cross recessed hexagon bolt with indetation single coil spring lock washer assembliesGB/T 9074.12-88 | UDC 621.882•十字槽凹穴六角头螺栓、弹簧垫圈和平垫圈组合件Cross recessed hexagon bolt with indetation,single coil lock washer and plain washer assembliesGB/T 9074.13-88 | UDC 621.882•钢结构用扭剪型高强度螺栓连接副Sets of torshear type high strength bolt hexagon nut and plain washer for steel structuresGB/T 3632-1995 | 代替GB3632-83•螺栓或螺钉和平垫圈组合件Bolt or screw and washer assemblies with plain washers GB/T 9074.1-2002 | 代替GB/T 9074.1、9074.14-1988•十字槽头螺钉和外锯齿锁紧垫圈组合件Cross recessed pan head screw and serrated lock washer external teeth assembliesGB/T 9074.2-88 | UDC 621.882•十字槽盘头螺钉和弹簧垫圈组合件Cross recessed pan head screw and single coll spring lock washer assembliesGB/T 9074.3-88 | UDC 621.882•十字槽盘头螺钉、弹簧垫圈和平垫圈组合件Cross recessed pan head screw, single coil spring lock washer assembliesGB/T 9074.4-88 | UDC 621.882•十字槽小盘头螺钉和平垫圈组合件Cross recessed small pan head screw and small plain washer assembliesGB/T 9074.5-88 | UDC 621.882•十字槽小盘头螺钉和大垫圈组合件Cross recessed small pan head screw and big plain washer assembliesGB/T 9074.6-88 | UDC 621.882•十字槽小盘头螺钉和弹簧垫圈组合件Cross recessed small pan head screw and single coil spring lock washer assembliesGB/T 9074.7-88 | UDC 621.882•十字槽小盘头螺钉、弹簧垫圈和平垫圈组合件Cross recessed small pan head screw, single coil spring lock washer and plain washer assembliesGB/T 9074.8-88 | UDC 621.882•十字槽沉头螺钉和锥形锁紧垫圈组合件Cross recessed countersunk head screw and countersunk serrated external toothed lock washer assembliesGB/T 9074.9-88 | UDC 621.882•十字槽凹穴六角头螺栓和平垫圈组合件Cross recessed hexagon bolt with indentation and plain washer assembliesGB/T 9074.11-88 | UDC 621.882•六角头螺栓和弹簧垫圈组合件Hexagon head bolt and single coil spring lock washer assembliesGB/T 9074.15-88 | UDC 621.882•六角头螺栓和外锯齿锁紧垫圈组合件Hexagon head bolt and serrated lock washer external teeth assembliesGB/T 9074.16-88 | UDC 621.882•钢结构用高强度大六角头螺栓High strength bolts with large hexagon head for steel structuresGB/T 1228-91 | 代替GB1228-84•钢结构用高强度大六角头螺母High strength large hexagon nuts for steel structures GB/T 1229-91 | 代替GB1229-84•钢结构用高强度垫圈High strength plain washers for steel structures GB/T 1230-91 | 代替GB1230-84.（注：素材和资料部分来自网络，供参考。
螺钉规格标准——GB标准
螺钉规格标准——GB标准规格标准——GB标准开槽圆柱头螺钉GB /T 65-2000开槽盘头螺钉GB /T 67-2000开槽沉头螺钉GB /T 68-2000开槽半沉头螺钉GB /T 69-2000内六角圆柱头螺钉GB /T 70.1-2000内六角平圆头螺钉GB /T 70.2-2000内六角沉头螺钉GB /T 70.3-2000开槽锥端紧定螺钉GB 71-85开槽锥端定位螺钉GB 72-88开槽平端紧定螺钉GB 73-85开槽凹端紧定螺钉GB 74-85开槽长圆柱端紧定螺钉GB 75-85内六角平端紧定螺钉GB /T 77-2000内六角锥端紧定螺钉GB /T 78-2000内六角圆柱端紧定螺钉GB /T 79-2000内六角凹端紧定螺钉GB /T 80-2000方头长圆柱球面端紧定螺钉GB 83-88 方头凹端紧定螺钉GB 84-88方头长圆柱端紧定螺钉GB 85-88方头短圆柱锥端紧定螺钉GB 86-88十字槽盘头螺钉GB /T 818-2000六角头不脱出螺钉GB 838-88滚花头不脱出螺钉GB 839-88塑料滚花头螺钉GB 840-88 开槽球面圆柱头轴位螺钉GB 946-88开槽球面大圆柱头螺钉GB 947-88开槽沉头不脱出螺钉GB 948-88开槽半沉头不脱出螺钉GB 949-88内六角花形盘头螺钉GB 2672-86内六角花形沉头螺钉GB 2673-86内六角花形半沉头螺钉GB 2674-86内六角圆柱头轴肩螺钉GB 5281-85内六角花形圆柱头螺钉-4.8级GB 6190-86内六角花形圆柱头螺钉-8.8和10.9级GB 6191-86 精密机械用紧固件十字槽螺钉GB /T 13806.1-92 十字槽半沉头螺钉GB /T 820-2000方头平端紧定螺钉GB 821-88十字槽圆柱头螺钉GB /T 822-2000十字槽小盘头螺钉GB 823-88吊环螺钉GB 825-88开槽盘头定位螺钉GB 828-88开槽圆柱端定位螺钉GB 829-88开槽圆柱头轴位螺钉GB 830-88开槽无头轴位螺钉GB 831-88开槽带孔球面圆柱头螺钉GB 832-88开槽大圆柱头螺钉GB 833-88滚花高头螺钉GB 834-88滚花平头螺钉GB 835-88滚花小头螺钉GB 836-88。
十字槽盘头螺钉标准
十字槽盘头螺钉标准十字槽盘头螺钉是一种十分常见的紧固件，它的标准化对于各行各业的生产制造至关重要。
在本文中，我们将重点介绍十字槽盘头螺钉的标准，以及其在工业生产中的应用和重要性。
首先，我们需要了解十字槽盘头螺钉的标准。
根据国际标准化组织（ISO）的规定，十字槽盘头螺钉的标准主要包括螺纹规格、材料要求、表面处理、尺寸精度等方面。
在螺纹规格方面，ISO 7045规定了十字槽盘头螺钉的螺纹参数，确保其能够与其他零部件配合良好。
而在材料要求和表面处理方面，ISO 7045和ISO 965-1则规定了螺钉的材料、硬度、表面镀层等要求，以确保其具有良好的耐腐蚀性和机械性能。
此外，ISO 7045还规定了螺钉的尺寸精度，以保证其在安装时能够达到预期的紧固效果。
其次，我们需要了解十字槽盘头螺钉在工业生产中的应用和重要性。
十字槽盘头螺钉广泛应用于机械设备、家具、电子产品、汽车制造等领域。
其盘头设计使得螺钉在安装时能够提供良好的扭矩传递和紧固效果，同时也方便安装人员使用螺丝刀进行操作。
由于其标准化，十字槽盘头螺钉能够与其他零部件互换使用，简化了生产制造过程，提高了生产效率。
此外，十字槽盘头螺钉的标准化也为产品的设计和维护提供了便利，使得不同厂家生产的产品能够共用标准件，降低了生产成本，提高了产品的质量和可靠性。
综上所述，十字槽盘头螺钉的标准化对于工业生产具有重要意义。
通过遵循ISO的标准，生产厂家能够生产出符合规范要求的螺钉，确保其具有良好的机械性能和耐腐蚀性，同时也提高了产品的可靠性和安全性。
标准化的十字槽盘头螺钉能够简化生产制造过程，降低生产成本，提高生产效率，对于推动工业生产的发展起到了重要的推动作用。
在实际生产中，我们应当严格遵循十字槽盘头螺钉的标准，选择符合规范要求的螺钉，并在安装过程中严格按照标准操作，以确保产品的质量和安全性。
同时，我们也应当加强对十字槽盘头螺钉标准的学习和理解，不断提高对标准化的重视和遵守，推动工业生产的可持续发展。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
级
径
度
度
min 力 sp
A1 奥
50
≤39 500
210
0.6d
500
..
..
氏体
A2 奥
70
≤20 700
450
0.4d
700
..
..
氏体
A4 奥
80
≤20 800
600
0.3d
800
..
..
氏体
规格
M2.0×0.40 M2.5×0.45 M3.0×0.50 M4.0×0.70 M5.0×0.80 M6.0×1.00 M8.0×1.25 M10×1.50 M12×1.75 M14×2.00 M16×2.00 M18×2.50 M20×2.50 M22×2.50 M24×3.00 M27×3.00 M30×3.50
19.50
19.744
21.00
21.252
24.00
24.252
26.50
26.771
min 1.567 2.013 2.459 3.242 4.134 4.917 6.647 8.376 10.106 11.835 13.835 15.294 17.294 19.294 20.752 23.752 26.211
产品介绍
1．螺丝的螺丝头外边是圆的，中间是凹进去的十字槽。2．螺丝常用于机械上, 主要有便于紧固,拆卸。3．不容易滑角等优势。主要运用于机械工业场所，汽车 装配，电力行业，风电场所，船用制造业，桥梁工程用，泵阀制造业，家具制造 业，电子行业，电器行业，通讯设备，建筑装修，机电专用行业，模具加工行业， 医学纺织行业，航空专用行业，军工铁路制造业等等五金行业设备。 尺寸规格说明
螺丝攻牙钻孔对照表
公制粗螺纹
标准径
2 级牙钻径 max
1.60
1.679
2.10
2.138
2.50
2.599
3.30
3.422
4.20
4.334
5.00
5.513
6.80
6.912
8.508.676 Nhomakorabea10.30
10.441
12.00
12.210
14.00
14.210
15.50
15.744
17.50
17.744
回火温 度C
min ..
6.8
..
0.55 0.05 0.06 0.003
..
8.8 淬火并回火低碳合金钢 0.15 0.04 0.035 0.035 0.003
425
淬火并回火的中碳钢
0.25 0.55 0.035 0.035
不锈钢性能等级
类别 性能等 螺纹直 抗拉强 屈服强 伸长量 保证应 螺栓，螺钉，螺母硬度 HRC
规格：螺纹规格 d=M5、公称长度 L=20mm、性能等级为4.8级、H 型十字
槽、不经表面处理的 A 级十字槽盘头螺钉的标记： 螺钉 GB/T 818 M5*20
产品参数
碳钢性 能等级
4.8
材料和热处理 碳钢
化学成分%
C
P
S
Min
max
max
max
..
0.55 0.05 0.06
B max
0.003