机械类外文翻译机械刀具库总装
机械常用词汇中英文对照
热处理常用词汇中英文对照热处理常用词汇中英文对照 indication 缺陷 test specimen 试样bar 棒材stock 原料billet 方钢，钢方坯bloom 钢坯,钢锭section 型材steel ingot 钢锭blank 坯料，半成品cast steel 铸钢nodular cast iron 球墨铸铁ductile cast iron 球墨铸铁bronze 青铜brass 黄铜copper 合金stainless steel不锈钢decarburization 脱碳scale 氧化皮anneal 退火process anneal 进行退火quenching 淬火normalizing 正火Charpy impact text 夏比冲击试验fatigue 疲劳tensile testing 拉伸试验solution 固溶处理aging 时效处理Vickers hardness维氏硬度Rockwell hardness 洛氏硬度Brinell hardness 布氏硬度hardness tester硬度计descale 除污，除氧化皮等ferrite 铁素体austenite 奥氏体martensite马氏体cementite 渗碳体iron carbide 渗碳体solid solution 固溶体sorbite 索氏体bainite 贝氏体pearlite 珠光体nodular fine pearlite/ troostite屈氏体black oxide coating 发黑grain 晶粒chromium 铬cadmium 镉tungsten 钨molybdenum 钼manganese 锰vanadium 钒molybdenum 钼silicon 硅sulfer/sulphur 硫phosphor/ phosphorus 磷nitrided 氮化的case hardening 表面硬化，表面淬硬air cooling 空冷furnace cooling 炉冷oil cooling 油冷electrocladding /plating 电镀brittleness 脆性strength 强度rigidity 刚性,刚度creep 蠕变deflection 挠度elongation 延伸率yield strength 屈服强度elastoplasticity 弹塑性metallographic structure 金相组织metallographic test 金相试验carbon content 含碳量induction hardening 感应淬火impedance matching 感应淬火hardening and tempering 调质crack 裂纹shrinkage 缩孔，疏松forging 锻（件）casting 铸（件）rolling 轧（件）drawing 拉（件）shot blasting 喷丸（处理）grit blasting 喷钢砂（处理）sand blasting 喷砂（处理）carburizing 渗碳nitriding 渗氮ageing/aging 时效grain size 晶粒度pore 气孔sonim 夹砂cinder inclusion 夹渣lattice晶格abrasion/abrasive/rub/wear/wearing resistance (property) 耐磨性 spectrum analysis光谱分析heat/thermal treatment 热处理inclusion 夹杂物segregation 偏析picking 酸洗，酸浸residual stress 残余应力remaining stress 残余应力relaxation of residual stress 消除残余应力stress relief 应力释放械类常用英语：常用加工机械械类常用英语：常用加工机械3D coordinate measurement 三次元量床boring machine 搪孔机cnc milling machine CNC铣床contouring machine 轮廓锯床copy grinding machine 仿形磨床copy lathe 仿形车床copy milling machine 仿形铣床copy shaping machine 仿形刨床cylindrical grinding machine 外圆磨床die spotting machine 合模机drilling machine ?孔机engraving machine 雕刻机engraving E.D.M. 雕模放置加工机form grinding machine 成形磨床graphite machine 石墨加工机horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心internal cylindrical machine 内圆磨床jig boring machine 冶具搪孔机jig grinding machine 冶具磨床lap machine 研磨机machine center 加工制造中心multi model miller 靠磨铣床NC drilling machine NC钻床NC grinding machine NC磨床NC lathe NC车床NC programming system NC程式制作系统planer 龙门刨床profile grinding machine 投影磨床projection grinder 投影磨床radial drilling machine 旋臂?床shaper 牛头刨床surface grinder 平面磨床try machine 试模机turret lathe 转塔车床universal tool grinding machine 万能工具磨床vertical machine center 立式加工制造中心wire E.D.M. 线割放电加工机机械术语中英文对照(二)Bending: 挠曲witness test订货人在场的试验Welding: 焊接Threading: 车缧纹Leveling：校平color identification 彩色识别Alignment：对准,定位调整check against 检查, 核对Fixing：固定Console：控制台cubicle室,箱audit 审计material certificate.材料合格证vertical panel竖直面板power distribution panel 配电盘gauge board仪表板beveling 磨斜棱,磨斜边local panel 现场配电盘grouting 灌浆fabrication 加工,制造instrument rack 计测器支架tank gauge 液面计flushing 冲洗，填缝analyzer分析器piping管道敷设tubing敷设管道cable fitting电缆配件elbow.弯管接头main pipe 主管道bend.弯管弯头solvent 溶剂postweld heat treatment 焊后热处理jig.夹具arc gouging 电弧刨削chipping修琢machining 机械加工bridges.管式桥clamp.夹钳tack welding 点焊butt welding 对接焊grinder. 磨床commencement.开始gusset plate角撑板, 加固板process pipe 工艺管道land 纹间表面tee 三通管丁字钢T形梁opening 开口reinforcing pad.补强垫,增强衬板flux 焊剂wet developer 湿显像剂blowhole气泡,气孔inclusion 杂质imperfection 缺陷limitation 限度valve 阀,闸门structural attachment 结构附件tapered allowance 削尖余量tack welding 平头焊接sputter 喷溅scale 废料lateral translation侧向平移weld joint 焊缝, 焊接接头plug.塞fusion 熔融base material基底材料lead foil 铅箔intensifying screen 增光屏, 光增强屏pressure test.压力试验film density.影片密度line number行数leak test漏泄试验plate thickness 筛板厚度restoration修理field fabricated 工地制造的,现场装配的junction box.接线盒flow sheet 流程图vent 放气孔, 通风孔drain 排水管instrument air仪表气源blind挡板pipe arrangement 管配置civil engineer.土木工程师bus duct 母线槽substation分站flow instrument 流量计power distribution panel 配电盘level instrument 位面计, 水平仪pressure instrument 压力仪表/压力计level switch (信号)电平开关,gage glass 液位玻璃管pilot tube指示灯line check 小检修recalibration.复校,重新校准blinding plate盲板expansion joint 伸缩接头hydrostatic pressure test静水压试验pneumatic pressure 气压scaffolding脚手架check valve止回阀liquid penetrant examination液体渗透探伤test pump试验泵witnessed inspections 现场检测hanger吊架control valve控制阀,fabrication drawing 制造图纸,制作图schedule number表示管壁厚度系列的号码hydrostatic test .流体静力学试验,水压试验design pressure 设计压力disposition notice 处罚通知书pipe stanchion 管支柱bellow type 波纹管式expansion joint 伸缩接头vibration stopper：减震器subcontractor 转包商WPS Works Process Specification 典型工艺规程piping.管道系统flange.凸缘sleeve 套筒ferritic .铁素体的identification mark 识别标志stencil.模绘片版,镂花模板stamping .冲压silicone paint硅树脂油漆weld bead 焊缝automatic temperature recorder 温度自动记录器penetrameter 透度计film viewer底片观察用光源civil works土建工程，建筑工程lump sum price 混合价格,统包价格scrap material废料caulking metal填隙合金[金属](材料) application drawing操作图, 应用图cable routing电缆路由选择channel bases沟渠基底vertical panel竖直面板local panel 现场配电盘power distribution panel 配电盘gauge board样板, 模板规准尺anchor bolt 锚定螺栓expansion bolt 伸缩栓, 扩开螺栓field instrument.携带式仪表instrument rack 计测器支架,计测器框架tank gauge 油箱液位计guide wire 尺度[定距]索,准绳name plate名牌, 商标lead pipe铅管take-off valve输出阀sub-header分联箱air header 集气管pneumatic signal气动信号steam trace 加热蒸汽管道electric heat tracing.电伴随加热cable trunk 电缆管道stop end封端fire barriers防火间隔bonding wire 接合线, 焊线conduit box [电]导管分线匣rigid conduits 刚性导管flexible conduit软管conduit entry 导管引入装置road crossing duct bank平交道口管道组Capping ends顶盖末端cable armor电缆铠装Cable sheath电缆包皮层sealing compound电缆膏coaxial cable同轴电缆loop test环路测试sequence test.联锁顺序试验lintel beam 水平横楣梁flash plate闪熔镀层anchor bolt 地脚螺栓expansion bolt伸缩栓, 扩开螺栓shim plate 垫板push button station按钮式控制站logic diagram逻辑图calculation sheet计算书flow instrument流量计level instrument 位面计, 水平仪layout drawing 布置图tie band捆扎用带材Heating boxes加热室cutting opening切孔control valve actuator 阀控传动机构air set空气中凝固, 常温自硬自然硬化solenoid valve.螺线管阀,电磁阀calorimeter热量计odometer历程标tachometer转速计chronometer精密计时表机械工具词汇中英文对照扳子spanner (美作:wrench)双头扳子double-ended spanner活扳子,活络扳手adjustable spanner, monkey wrench 管钳子box spanner (美作:socket wrench)卡规calipers夹钳pincers, tongs剪子shears钢锯hacksaw剪线钳wire cutters万能手钳multipurpose pliers, universal pliers可调手钳adjustable pliers冲子punch钻drill卡盘chuck三角刮刀scraper扩孔钻reamer孔径规calliper gauge铆钉rivet螺母nut自锁螺母,防松螺母locknut螺栓bolt销钉pin, peg, dowel垫圈washerU形钉staple油壶oil can工作服jack注油枪grease gun机械加工抛光polishing安装to assemble衬套bushing半机械化semi-mechanization; semi-mechanized 半自动滚刀磨床semi-automatic hob grinder半自动化semi-automation; semi-automatic扳手wrench备件spare parts边刨床side planer变速箱transmission gear柄轴arbor部件units; assembly parts插床slotting machine拆卸to disassemble超高速内圆磨床ultra-high-speed internal grinder 车床lathe; turning lathe车刀lathe tool车轮车床car wheel lathe车削turning车轴axle模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder文件夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerazation装箱quantity of physical invetory second count 复盘点数量quantity of customs count会计师盘,点数量the first page第一联filed by accounting department for reference会计部存查end-user/using unit(department)使用单位summary of year-end physical inventory bills年终盘点截止单据汇总表bill name单据名称This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheetPCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill钻boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板)stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣组装、冲压、喷漆等专业词汇Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技（生产技术）cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch镑、英寸EMI gasket导电条front plate前板rear plate后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS电源电压接拉键sheet metal parts 冲件plastic parts塑胶件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource department人力资源部personnel [ ]1. (总称)人员,员工 2. 人事部门;人事课(或室等)production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |'plein|刨床miller铣床grinder磨床driller??床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skræpid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dei n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓name of a department部门名称administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车forklift叉车pallet栈板glove(s)手套glove(s) with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头sweeper扫把mop拖把vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机production line流水线chain链条槽magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位safety安全quality品质delivery deadline交货期cost成本engineering工程die repair模修enterprise plan = enterprise expansion projects企划QC品管die worker模工production, to produce生产equipment设备to start a press开机stop/switch off a press关机classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products, up-to-grade products良品defective products, not up-to-grade products不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱die change 换模to fix a die装模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, not qualified不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for 准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位lots of production生产批量steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify修订to switch over to, switch---to throw--over switching over切换engineering, project difficulty工程瓶颈stage die工程模automation自动化to stake, staking, reviting铆合add lubricating oil加润滑油shut die架模shut height of a die架模高度analog-mode device类模器die lifter举模器argon welding氩焊vocabulary for stamping冲压常词汇stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to.to send delinery backto retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑common vocabulary for die engineering 金属切削metal cutting机床machine tool金属工艺学technology of metals刀具cutter电路circuit半导体元件semiconductor element反馈feedback发生器generator直流电源DC electrical source门电路gate circuit逻辑代数logic algebra逻辑电路logic circuit触发器flip-flop脉冲波形pulse shape数模digital analogy液压传动机构fluid drive mechanism 机械零件mechanical parts摩擦friction联结link传动drive/transmission轴shaft弹性elasticity频率特性frequency characteristic误差error响应response定位allocation机床夹具jig动力学dynamic运动学kinematic静力学static分析力学analyse mechanics拉伸pulling压缩hitting剪切shear扭转twist弯曲应力bending stress强度intensity三相交流电three-phase AC磁路magnetic circles变压器transformer异步电动机asynchronous motor几何形状geometrical精度precision正弦形的sinusoid交流电路AC circuit机械加工余量machining allowance 变形力deforming force变形deformation应力stress硬度rigidity热处理heat treatment退火anneal正火normalizing脱碳decarburization渗碳carburization淬火冷却quench淬火hardening回火tempering调质hardening and tempering 磨粒abrasive grain结合剂bonding agent砂轮grinding wheel外圆磨削external grinding内圆磨削internal grinding平面磨削plane grinding变速箱gearbox离合器clutch绞孔fraising绞刀reamer螺纹加工thread processing螺钉screw铣削mill铣刀milling cutter功率power工件workpiece齿轮加工gear mechining齿轮gear主运动main movement主运动方向direction of main movement进给方向direction of feed进给运动feed movement合成进给运动resultant movement of feed合成切削运动resultant movement of cutting合成切削运动方向direction of resultant movement of cutting 切削深度cutting depth前刀面rake face刀尖nose of tool前角rake angle后角clearance angle龙门刨削planing主轴spindle主轴箱headstock卡盘chuck加工中心machining center车刀lathe tool车床lathe钻削镗削bore车削turning磨床grinder基准benchmark钳工locksmith锻forge压模stamping焊weld拉床broaching machine拉孔broaching装配assembling铸造found流体动力学fluid dynamics流体力学fluid mechanics加工machining液压hydraulic pressure切线tangent机电一体化mechanotronics mechanical-electrical integration 气压air pressure pneumatic pressure稳定性stability介质medium液压驱动泵fluid clutch液压泵hydraulic pump阀门valve失效invalidation强度intensity载荷load应力stress安全系数safty factor可靠性reliability螺纹thread螺旋helix键spline销pin滚动轴承rolling bearing滑动轴承sliding bearing弹簧spring制动器arrester brake十字结联轴节crosshead联轴器coupling链chain皮带strap精加工finish machining粗加工rough machining变速箱体gearbox casing腐蚀rust氧化oxidation磨损wear耐用度durability随机信号random signal离散信号discrete signal超声传感器ultrasonic sensor 集成电路integrate circuit挡板orifice plate。
机械加工刀具中英文对照外文翻译文献
中英文对照外文翻译英文原文Selection of optimum tool geometry and cutting conditionsusing a surface roughness prediction model for end milling Abstract Influence of tool geometry on the quality of surface produced is well known and hence any attempt to assess the performance of end milling should include the tool geometry. In the present work, experimental studies have been conducted to see the effect of tool geometry (radial rake angle and nose radius) and cutting conditions (cutting speed and feed rate) on the machining performance during end milling of medium carbon steel. The first and second order mathematical models, in terms of machining parameters, were developed for surface roughness prediction using response surface methodology (RSM) on the basis of experimental results. The model selected for optimization has been validated with the Chi square test. The significance of these parameters on surface roughness has been established with analysis of variance. An attempt has also been made to optimize the surface roughness prediction model using genetic algorithms (GA). The GA program gives minimum values of surface roughness and their respective optimal conditions.1 IntroductionEnd milling is one of the most commonly used metal removal operations in industry because of its ability to remove material faster giving reasonably good surface quality. It is used in a variety of manufacturing industries including aerospace and automotive sectors, where quality is an important factor in the production of slots, pockets, precision moulds and dies. Greater attention is given to dimensional accuracy and surface roughness of products by the industry these days. Moreover, surface finish influences mechanical properties such as fatigue behaviour, wear, corrosion, lubrication and electrical conductivity. Thus, measuring and characterizing surface finish can be considered for predicting machining performance.Surface finish resulting from turning operations has traditionally received considerable research attention, where as that of machining processes using multipoint cutters, requires attention by researchers. As these processes involve large number of parameters, it would bedifficult to correlate surface finish with other parameters just by conducting experiments. Modelling helps to understand this kind of process better. Though some amount of work has been carried out to develop surface finish prediction models in the past, the effect of tool geometry has received little attention. However, the radial rake angle has a major affect on the power consumption apart from tangential and radial forces. It also influences chip curling and modifies chip flow direction. In addition to this, researchers [1] have also observed that the nose radius plays a significant role in affecting the surface finish. Therefore the development of a good model should involve the radial rake angle and nose radius along with other relevant factors.Establishment of efficient machining parameters has been a problem that has confronted manufacturing industries for nearly a century, and is still the subject of many studies. Obtaining optimum machining parameters is of great concern in manufacturing industries, where the economy of machining operation plays a key role in the competitive market. In material removal processes, an improper selection of cutting conditions cause surfaces with high roughness and dimensional errors, and it is even possible that dynamic phenomena due to auto excited vibrations may set in [2]. In view of the significant role that the milling operation plays in today’s manufacturing world, there is a need to optimize the machining parameters for this operation. So, an effort has been made in this paper to see the influence of tool geometry(radial rake angle and nose radius) and cutting conditions(cutting speed and feed rate) on the surface finish produced during end milling of medium carbon steel. The experimental results of this work will be used to relate cutting speed, feed rate, radial rake angle and nose radius with the machining response i.e. surface roughness by modelling. The mathematical models thus developed are further utilized to find the optimum process parameters using genetic algorithms.2 ReviewProcess modelling and optimization are two important issues in manufacturing. The manufacturing processes are characterized by a multiplicity of dynamically interacting process variables. Surface finish has been an important factor of machining in predicting performance of any machining operation. In order to develop and optimize a surface roughness model, it is essential to understand the current status of work in this area.Davis et al. [3] have investigated the cutting performance of five end mills having various helix angles. Cutting tests were performed on aluminium alloy L 65 for three milling processes (face, slot and side), in which cutting force, surface roughness and concavity of a machined plane surface were measured. The central composite design was used to decide on the number ofexperiments to be conducted. The cutting performance of the end mills was assessed using variance analysis. The affects of spindle speed, depth of cut and feed rate on the cutting force and surface roughness were studied. The investigation showed that end mills with left hand helix angles are generally less cost effective than those with right hand helix angles. There is no significant difference between up milling and down milling with regard tothe cutting force, although the difference between them regarding the surface roughness was large. Bayoumi et al.[4] have studied the affect of the tool rotation angle, feed rate and cutting speed on the mechanistic process parameters (pressure, friction parameter) for end milling operation with three commercially available workpiece materials, 11 L 17 free machining steel, 62- 35-3 free machining brass and 2024 aluminium using a single fluted HSS milling cutter. It has been found that pressure and friction act on the chip – tool interface decrease with the increase of feed rate and with the decrease of the flow angle, while the cutting speed has a negligible effect on some of the material dependent parameters. Process parameters are summarized into empirical equations as functions of feed rate and tool rotation angle for each work material. However, researchers have not taken into account the effects of cutting conditions and tool geometry simultaneously; besides these studies have not considered the optimization of the cutting process.As end milling is a process which involves a large number f parameters, combined influence of the significant parameters an only be obtained by modelling. Mansour and Abdallaet al. [5] have developed a surface roughness model for the end milling of EN32M (a semi-free cutting carbon case hardening steel with improved merchantability). The mathematical model has been developed in terms of cutting speed, feed rate and axial depth of cut. The affect of these parameters on the surface roughness has been carried out using response surface methodology (RSM). A first order equation covering the speed range of 30–35 m/min and a second order equation covering the speed range of 24–38 m/min were developed under dry machining conditions. Alauddin et al. [6] developed a surface roughness model using RSM for the end milling of 190 BHN steel. First and second order models were constructed along with contour graphs for the selection of the proper combination of cutting speed and feed to increase the metal removal rate without sacrificing surface quality. Hasmi et al. [7] also used the RSM model for assessing the influence of the workpiece material on the surface roughness of the machined surfaces. The model was developed for milling operation by conducting experiments on steel specimens. The expression shows, the relationship between the surface roughness and the various parameters; namely, the cutting speed, feed and depth of cut. The above models have not considered the affect of tool geometry on surface roughness.Since the turn of the century quite a large number of attempts have been made to find optimum values of machining parameters. Uses of many methods have been reported in the literature to solve optimization problems for machining parameters. Jain and Jain [8] have used neural networks for modeling and optimizing the machining conditions. The results have been validated by comparing the optimized machining conditions obtained using genetic algorithms. Suresh et al. [9] have developed a surface roughness prediction model for turning mild steel using a response surface methodology to produce the factor affects of the individual process parameters. They have also optimized the turning process using the surface roughness prediction model as the objective function. Considering the above, an attempt has been made in this work to develop a surface roughness model with tool geometry and cutting conditions on the basis of experimental results and then optimize it for the selection of these parameters within the given constraints in the end milling operation.3 MethodologyIn this work, mathematical models have been developed using experimental results with the help of response surface methodolog y. The purpose of developing mathematical models relating the machining responses and their factors is to facilitate the optimization of the machining process. This mathematical model has been used as an objective function and the optimization was carried out with the help of genetic algorithms.3.1 Mathematical formulationResponse surface methodology(RSM) is a combination of mathematical and statistical techniques useful for modelling and analyzing the problems in which several independent variables influence a dependent variable or response. The mathematical models commonly used are represented by:where Y is the machining response, ϕ is the response function and S, f , α, r are milling variables and ∈is the error which is normally distributed about the observed response Y with zero mean.The relationship between surface roughness and other independent variables can be represented as follows，where C is a constant and a, b, c and d are exponents.To facilitate the determination of constants and exponents, this mathematical model will have to be linearized by performing a logarithmic transformation as follows:The constants and exponents C, a, b, c and d can be determined by the method of least squares. The first order linear model, developed from the above functional relationship using least squares method, can be represented as follows:where Y1 is the estimated response based on the first-order equation, Y is the measured surface roughness on a logarithmic scale, x0 = 1 (dummy variable), x1, x2, x3 and x4 are logarithmic transformations of cutting speed, feed rate, radial rake angle and nose radius respectively, ∈is the experimental error and b values are the estimates of corresponding parameters.The general second order polynomial response is as given below:where Y2 is the estimated response based on the second order equation. The parameters, i.e. b0, b1, b2, b3, b4, b12, b23, b14, etc. are to be estimated by the method of least squares. Validity of the selected model used for optimizing the process parameters has been tested with the help of statistical tests, such as F-test, chi square test, etc. [10].3.2 Optimization using genetic algorithmsMost of the researchers have used traditional optimization techniques for solving machining problems. The traditional methods of optimization and search do not fare well over a broad spectrum of problem domains. Traditional techniques are not efficient when the practical search space is too large. These algorithms are not robust. They are inclined to obtain a local optimal solution. Numerous constraints and number of passes make the machining optimization problem more complicated. So, it was decided to employ genetic algorithms as an optimization technique. GA come under the class of non-traditional search and optimization techniques. GA are different from traditional optimization techniques in the following ways:1.GA work with a coding of the parameter set, not the parameter themselves.2.GA search from a population of points and not a single point.3.GA use information of fitness function, not derivatives or other auxiliary knowledge.4.GA use probabilistic transition rules not deterministic rules.5.It is very likely that the expected GA solution will be the global solution.Genetic algorithms (GA) form a class of adaptive heuristics based on principles derived from the dynamics of natural population genetics. The searching process simulates the natural evaluation of biological creatures and turns out to be an intelligent exploitation of a random search. The mechanics of a GA is simple, involving copying of binary strings. Simplicity of operation and computational efficiency are the two main attractions of the genetic algorithmic approach. The computations are carried out in three stages to get a result in one generation oriteration. The three stages are reproduction, crossover and mutation.In order to use GA to solve any problem, the variable is typically encoded into a string (binary coding) or chromosome structure which represents a possible solution to the given problem. GA begin with a population of strings (individuals) created at random. The fitness of each individual string is evaluated with respect to the given objective function. Then this initial population is operated on by three main operators – reproduction cross over and mutation– to create, hopefully, a better population. Highly fit individuals or solutions are given the opportunity to reproduce by exchanging pieces of their genetic information, in the crossover procedure, with other highly fit individuals. This produces new “offspring” solutions, which share some characteristics taken from both the parents. Mutation is often applied after crossover by altering some genes (i.e. bits) in the offspring. The offspring can either replace the whole population (generational approach) or replace less fit individuals (steady state approach). This new population is further evaluated and tested for some termination criteria. The reproduction-cross over mutation- evaluation cycle is repeated until the termination criteria are met.中文翻译选择最佳工具，几何形状和切削条件利用表面粗糙度预测模型端铣摘要：刀具几何形状对工件表面质量产生的影响是人所共知的，因此，任何成型面端铣设计应包括刀具的几何形状。
机械加工刀具中英文对照外文翻译文献
机械加工刀具中英文对照外文翻译文献(文档含英文原文和中文翻译)中英文对照外文翻译英文原文Selection of optimum tool geometry and cutting conditions using a surface roughness prediction model for end milling Abstract Influence of tool geometry on the quality of surface produced is well known and hence any attempt to assess the performance of end milling should include the tool geometry. In the present work, experimental studies have been conducted to see the effect of tool geometry (radial rake angle and nose radius) and cutting conditions (cutting speed and feed rate) on the machining performance during end milling of medium carbon steel. The first and second ordermathematical models, in terms of machining parameters, were developed for surface roughness prediction using response surface methodology (RSM) on the basis of experimental results. The model selected for optimization has been validated with the Chi square test. The significance of these parameters on surface roughness has been established with analysis of variance. An attempt has also been made to optimize the surface roughness prediction model using genetic algorithms (GA). The GA program gives minimum values of surface roughness and their respective optimal conditions.1 IntroductionEnd milling is one of the most commonly used metal removal operations in industry because of its ability to remove material faster giving reasonably good surface quality. It is used in a variety of manufacturing industries including aerospace andautomotive sectors, where quality is an important factor in the production of slots, pockets, precision moulds and dies. Greater attention is given to dimensional accuracy and surface roughness of products by the industry these days. Moreover, surface finish influences mechanical properties such as fatigue behaviour, wear, corrosion, lubrication and electrical conductivity. Thus, measuring and characterizing surface finish can be considered for predicting machining performance.Surface finish resulting from turning operations has traditionally received considerable research attention, where as that of machining processes using multipoint cutters, requires attention by researchers. As these processes involve large number of parameters, it would be difficult to correlate surface finish with other parameters just by conducting experiments. Modelling helps to understand this kind of process better. Though some amount of work has been carried out to develop surface finish prediction models in the past, the effect of tool geometry has received little attention. However, the radial rake angle has a major affect on the power consumption apart from tangential and radial forces. It also influences chip curling and modifies chip flow direction. In addition to this, researchers [1] have also observed that the nose radius plays a significant role in affecting the surface finish. Therefore the development of a good model should involve the radial rake angle and nose radius along with other relevant factors.Establishment of efficient machining parameters has been a problem that has confronted manufacturing industries for nearly a century, and is still the subject of many studies. Obtaining optimum machining parameters is of great concern in manufacturing industries, where the economy of machiningoperation plays a key role in the competitive market. In material removal processes, an improper selection of cutting conditions cause surfaces with high roughness anddimensional errors, and it is even possible that dynamic phenomena due to auto excited vibrations may set in [2]. In view of the significant role that the milling operation plays in today’s manufacturing world, there is a need to optimize the machining parameters for this operation. So, an effort has been made in this paper to see the influence of tool geometry(radial rake angle and nose radius) and cutting conditions(cutting speed and feed rate) on the surface finish produced during end milling of medium carbon steel. The experimental results of this work will be used to relate cutting speed, feed rate, radial rake angle and nose radius with the machining response i.e. surface roughness by modelling. The mathematical models thus developed are further utilized to find the optimum process parameters using genetic algorithms.2 ReviewProcess modelling and optimization are two important issues in manufacturing. The manufacturing processes are characterized by a multiplicity of dynamically interacting process variables. Surface finish has been an important factor of machining in predicting performance of any machining operation. In order to develop and optimize a surface roughness model, it is essential to understand the current status of work in this area.Davis et al. [3] have investigated the cutting performance of five end mills having various helix angles. Cutting tests were performed on aluminium alloy L 65 for three milling processes (face, slot and side), in which cutting force, surface roughnessand concavity of a machined plane surface were measured. The central composite design was used to decide on the number of experiments to be conducted. The cutting performance of the end mills was assessed using variance analysis. The affects of spindle speed, depth of cut and feed rate on the cutting force and surface roughness were studied. The investigation showed that end mills with left hand helix angles are generally less cost effective than those with right hand helix angles. There is no significant difference between up milling and down milling with regard tothe cutting force, although the difference between them regarding the surface roughness was large. Bayoumi et al.[4] have studied the affect of the tool rotation angle, feed rate and cutting speed on the mechanistic process parameters (pressure, friction parameter) for end milling operation with three commercially available workpiece materials, 11 L 17 free machining steel, 62- 35-3 free machining brass and 2024 aluminium using a single fluted HSS milling cutter. It has been found that pressure and friction act on the chip – tool interface decrease with the increase of feed rate and with the decrease of the flow angle, while the cutting speed has a negligible effect on some of the material dependent parameters. Process parameters are summarized into empirical equations as functions of feed rate and tool rotation angle for each work material. However, researchers have not taken into account the effects of cutting conditions and tool geometry simultaneously; besides these studies have not considered the optimization of the cutting process.As end milling is a process which involves a large number f parameters, combined influence of the significant parameters an only be obtained by modelling. Mansour and Abdallaet al. [5]have developed a surface roughness model for the end milling of EN32M (a semi-free cutting carbon case hardening steel with improved merchantability). The mathematical model has been developed in terms of cutting speed, feed rate and axial depth of cut. The affect of these parameters on the surface roughness has been carried out using response surface methodology (RSM). A first order equation covering the speed range of 30–35 m/min and a second order equation covering the speed range of 24–38 m/min were developed under dry machining conditions. Alauddin et al. [6] developed a surface roughness model using RSM for the end milling of 190 BHN steel. First and second order models were constructed along with contour graphs for the selection of the proper combination of cutting speed and feed to increase the metal removal rate without sacrificing surface quality. Hasmi et al. [7] also used the RSM model for assessing the influence of the workpiece material on the surface roughness of the machined surfaces. The model was developed for milling operation by conducting experiments on steel specimens. The expression shows, the relationship between the surface roughness and the various parameters; namely, the cutting speed, feed and depth of cut. The above models have not considered the affect of tool geometry on surface roughness.Since the turn of the century quite a large number of attempts have been made to find optimum values of machining parameters. Uses of many methods have been reported in the literature to solve optimization problems for machining parameters. Jain and Jain [8] have used neural networks for modeling and optimizing the machining conditions. The results have been validated by comparing the optimized machining conditions obtained using genetic algorithms. Suresh et al. [9]have developed a surface roughness prediction model for turning mild steel using a response surface methodology to produce the factor affects of the individual process parameters. They have also optimized the turning process using the surface roughness prediction model as the objective function. Considering the above, an attempt has been made in this work to develop a surface roughness model with tool geometry and cutting conditions on the basis of experimental results and then optimize it for the selection of these parameters within the given constraints in the end milling operation.3 MethodologyIn this work, mathematical models have been developed using experimental results with the help of response surface methodolog y. The purpose of developing mathematical models relating the machining responses and their factors is to facilitate the optimization of the machining process. This mathematical model has been used as an objective function and the optimization was carried out with the help of genetic algorithms.3.1 Mathematical formulationResponse surface methodology(RSM) is a combination of mathematical and statistical techniques useful for modelling and analyzing the problems in which several independent variables influence a dependent variable or response. The mathematical models commonly used are represented by:where Y is the machining response, ? is the response function and S, f , α, r are milling variables and ∈is the error which is normally distributed about the observed response Y with zero mean.The relationship between surface roughness and other independent variables can be represented as follows，where C isa constant and a, b, c and d are exponents.To facilitate the determination of constants and exponents, this mathematical model will have to be linearized by performing a logarithmic transformation as follows:The constants and exponents C, a, b, c and d can be determined by the method of least squares. The first order linear model, developed from the above functional relationship using least squares method, can be represented as follows: where Y1 is the estimated response based on the first-order equation, Y is the measured surface roughness on a logarithmic scale, x0 = 1 (dummy variable), x1, x2, x3 and x4 are logarithmic transformations of cutting speed, feed rate, radial rake angle and nose radius respectively, ∈is the experimental error and b values are the estimates of corresponding parameters.The general second order polynomial response is as given below:where Y2 is the estimated response based on the second order equation. The parameters, i.e. b0, b1, b2, b3, b4, b12, b23, b14, etc. are to be estimated by the method of least squares. Validity of the selected model used for optimizing the process parameters has been tested with the help of statistical tests, such as F-test, chi square test, etc. [10].3.2 Optimization using genetic algorithmsMost of the researchers have used traditional optimization techniques for solving machining problems. The traditional methods of optimization and search do not fare well over a broad spectrum of problem domains. Traditional techniques are not efficient when the practical search space is too large. These algorithms are not robust. They are inclined to obtain a local optimal solution. Numerous constraints and number of passesmake the machining optimization problem more complicated. So, it was decided to employ genetic algorithms as an optimization technique. GA come under the class of non-traditional search and optimization techniques. GA are different from traditional optimization techniques in the following ways:1.GA work with a coding of the parameter set, not the parameter themselves.2.GA search from a population of points and not a single point.3.GA use information of fitness function, not derivatives or other auxiliary knowledge.4.GA use probabilistic transition rules not deterministic rules.5.It is very likely that the expected GA solution will be the global solution.Genetic algorithms (GA) form a class of adaptive heuristics based on principles derived from the dynamics of natural population genetics. The searching process simulates the natural evaluation of biological creatures and turns out to be an intelligent exploitation of a random search. The mechanics of a GA is simple, involving copying of binary strings. Simplicity of operation and computational efficiency are the two main attractions of the genetic algorithmic approach. The computations are carried out in three stages to get a result in one generation or iteration. The three stages are reproduction, crossover and mutation.In order to use GA to solve any problem, the variable is typically encoded into a string (binary coding) or chromosome structure which represents a possible solution to the given problem. GA begin with a population of strings (individuals) created at random. The fitness of each individual string isevaluated with respect to the given objective function. Then this initial population is operated on by three main operators –reproduction cross over and mutation–to create, hopefully, a better population. Highly fit individuals or solutions are given the opportunity to reproduce by exchanging pieces of their genetic information, in the crossover procedure, with other highly fit individuals. This produces new “offspring” solutions, which share some characteristics taken from both the parents. Mutation is often applied after crossover by altering some genes (i.e. bits) in the offspring. The offspring can either replace the whole population (generational approach) or replace less fit individuals (steady state approach). This new population is further evaluated and tested for some termination criteria. The reproduction-cross over mutation- evaluation cycle is repeated until the termination criteria are met.中文翻译选择最佳工具，几何形状和切削条件利用表面粗糙度预测模型端铣摘要：刀具几何形状对工件表面质量产生的影响是人所共知的，因此，任何成型面端铣设计应包括刀具的几何形状。
机械行业工具量具术语-中英文对照
中文名称 pressure machine vice parallel sets Tee-bolt washer magnetic tables magnetic handing engineer's files diamond riffler files burrs
英文名称
磁性工作台 磁性手柄 锉刀 金刚石修模锉刀 打磨头 打磨头和抛光头 纱布带 打磨片(磨砂片) 磨砂片 磨砂带片 硬毛打磨片(去毛刺刷) 通用研磨砂块 砂布薄片和附件 砂带 油石（磨石） 粗砂轮 砂轮 金属丝圆形打磨刷 钢丝刷（手用） 洗瓶刷、管道刷、钳工刷 毛刷 钢锯条 圆锯片 开口扳手 双端梅花双头扳手 套筒扳手 螺母扳手系列 螺丝起子 六角扳手 可调钩型扳手 套筒套装系列带有方形 电子扭力校正器 电子扭力扳手 扭矩扳手 带表盘扭矩扳手(数显式) 扭矩扳手(可调节) 扭矩扳手(快速的调节) 螺丝刀 VAE绝缘组合钳
序号中文名称虎钳pressuremachinevice垫圈washer磁性工作台magnetictables磁性手柄magnetichanding锉刀engineersfiles金刚石修模锉刀diamondrifflerfiles打磨头burrs10打磨头和抛光头grindingandpolishingpoints11纱布带sanderbands12abrasivediscflapdisc13磨砂片flapwheels14磨砂带片cleanandstripdiscs15bristlecleaningdiscstooling16通用研磨砂块universalabrasivecleaners17砂布薄片和附件sheetsofabrasiveclothandaccessories18linishingbeltsendless19油石磨石oilstoneshones20粗砂轮roughgrindingdisc21砂轮grindingwheels22金属丝圆形打磨刷circularwirebrushessteel23钢丝刷手用wirehandscratchbrushes24洗瓶刷管道刷钳工刷25毛刷paintbrushes26钢锯条hacksawblade27圆锯片circularsawbladescarbidetipped28开口扳手openendedspanners29双端梅花双头扳手doubleendedringspanners30套筒扳手boxspannerssocketwrenches31螺母扳手系列nutspannersetinwallet32螺丝起子screwdrivers33六角扳手hexagonkeylwrenchsets34可调钩型扳手adjustchookpinspanners35套筒套装系列带有方形socketsetswith14and12squaredrive36电子扭力校正器electronictorqueanalysers37电子扭力扳手electronictorquewrenches38扭矩扳手rotationalanglewrenches3940torquewrencheswithadjustmentscaleautomatictrigger41torquewrencheswithquickadjustment42螺丝刀bladescrewdrives43heavydutycombinat
机床术语中英文对照表
Grinding tools
磨削工具
Grinding wheels
磨轮
Hand tools
手工具
Hard/soft ａnd free expansion sheet making plant
硬（软）板（片）材及自由发泡板机组
Heat preserving furnaces
保温炉
Heating treatment funaces
磁性工具
Manifolds
集合管
Milling heads
铣头
Milling machines
铣床
Milling machines,bed type
床身式铣床
Milling machines，duplicating
仿形铣床
Milling machines,horizontal
卧式铣床
Milling machines，turret vertical
精研机
Lapping machines,centerless
无心精研机
Laser cutting
激光切割
Laser cutting for SMT stensil
激光钢板切割机
Lathe bench
车床工作台
Lathes，automatic
自动车床
Lathes,heavy—duty
重型车床
Lathes，high-speed
高速车床
Lathes,turret
六角车床
Lathes，vertiubrication Systems
润滑系统
Lubricators
注油机
Machining centers,general
机床术语中英文对照表
Manifolds
集合管
Milling heads
铣头
Milling machines
铣床
Milling machines,bed type
床身式铣床
Milling machines,duplicating
仿形铣床
Milling machines,horizontal
卧式铣床
Milling machines,turret vertical
铝轮冒口切断机
P type PVC waterproof rolled sheet making plant
P型PVC高分子防水
PCB fine piecing systems
印刷电器板油压冲孔脱料系统
Pipe & tube making machines
管筒制造机
Planing machines
刨床
电动刀具
Engraving machines
雕刻机
Engraving machines,laser
激光雕刻机
Etching machines
蚀刻机
Finishing machines
修整机
Fixture
夹具
Forging dies
锻模
Forging,aluminium
锻铝
Forging,cold
冷锻
自动压力机
Pressing dies
压模
Punch formers
冲子研磨器
Quick die change systems
速换模系统
Quick mold change systems
快速换模系统
Reverberatory furnaces
机械专业实用英语词汇
★以下是英⽂写作翻译频道为⼤家整理的《机械专业实⽤英语词汇》，供⼤家参考。
更多内容请看本站频道。
⾦属切削 metal cutting机床 machine tool⾦属⼯艺学 technology of metals⼑具 cotter摩擦 friction联结 link传动 drive/transmission轴 shaft弹性 elasticity频率特性 frequency characteristic误差 error响应 response定位 allocation机床夹具 jig动⼒学 dynamic运动学 kinematics静⼒学 static分析⼒学 analyze mechanics拉伸 pulling压缩 hitting剪切 shear扭转 twist弯曲应⼒ bending stress强度 intensity三相交流电 three-phase AC磁路 magnetic circles变压器 transformer异步电动机 asynchronous motor⼏何形状 geometrical精度 precision正弦形的 sinusoid交流电路 AC circuit机械加⼯余量 machining allowance变形⼒ deforming force变形 deformation应⼒ stress硬度 rigidity热处理 heat treatment退⽕ anneal正⽕ normalizing脱碳 decarburization渗碳 carburization电路 circuit半导体元件 semiconductor element反馈 feedback发⽣器 generator直流电源 DC electrical source门电路 gate circuit逻辑代数 logic algebra外圆磨削 external grinding内圆磨削 internal grinding平⾯磨削 plane grinding变速箱 gearbox离合器 clutch绞孔 fraising绞⼑ reamer螺纹加⼯ thread processing螺钉 screw铣削 mill铣⼑ milling cutter功率 power⼯件 work piece齿轮加⼯ gear machining齿轮 gear主运动 main movement主运动⽅向 direction of aim movement进给⽅向 direction of feed进给运动 feed movement合成进给运动 resultant movement of feed合成切削运动 resultant movement of cutting合成切削运动⽅向 direction of resultant movement of cutting 切削深度 cutting depth前⼑⾯ rake face⼑尖 nose of toll前⾓ rake angle后⾓ clearance angle龙门刨削 planning主轴 spindle主轴箱 headstock卡盘 chuck加⼯中⼼ machining center车⼑ lathe tool车床 lathe钻削镗削 bore车削 turning磨床 grinder基准 benchmark钳⼯ locksmith锻 forge压模 stamping焊 weld拉床 broaching machine拉孔 broaching装配 assembling铸造 found流体动⼒学 fluid dynamics流体⼒学 fluid mechanics加⼯ machining液压 hydraulic pressure切线 tangent机电⼀体化 mechanotronics mechanical-electrical integration ⽓压 air pressure pneumatic pressure稳定性 stability介质 medium液压驱动泵 fluid clutch液压泵 hydraulic pump阀门 valve失效 invalidation强度 intensity载荷 load应⼒ stress安全系数 safty factor可靠性 reliability螺纹 thread螺旋 helix键 spline销 pin滚动轴承 rolling bearing滑动轴承 sliding bearing弹簧 spring制动器 arrester brake⼗字结联轴节 crosshead联轴器 coupling链 chain⽪带 strap精加⼯ finish machining粗加⼯ rough machining变速箱体 gearbox casing腐蚀 rust氧化 oxidation磨损 wear耐⽤度 durability随机信号 random signal离散信号 discrete signal超声传感器 ultrasonic sensor集成电路 integrate circuit挡板 orifice plate残余应⼒ residual stress套筒 sleeve扭⼒ torsion冷加⼯ cold machining电动机 electromotor汽缸 cylinder过盈配合 interference fit热加⼯ hotwork摄像头 CCD camera倒⾓ rounding chamfer优化设计 optimal design⼯业造型设计 industrial molding design有限元 finite element滚齿 hobbling插齿 gear shaping伺服电机 actuating motor铣床 milling machine钻床 drill machine镗床 boring machine步进电机 stepper motor丝杠 screw rod导轨 lead rail组件 subassembly可编程序逻辑控制器 Programmable Logic Controller PLC 电⽕花加⼯ electric spark machining电⽕花线切割加⼯ electrical discharge wire - cutting相图 phase diagram热处理 heat treatment固态相变 solid state phase changes有⾊⾦属 nonferrous metal陶瓷 ceramics合成纤维 synthetic fiber电化学腐蚀 electrochemical corrosion车架 automotive chassis悬架 suspension转向器 redirector变速器 speed changer板料冲压 sheet metal parts孔加⼯ spot facing machining车间 workshop⼯程技术⼈员 engineer⽓动夹紧 pneumatic lock数学模型 mathematical model画法⼏何 descriptive geometry机械制图 Mechanical drawing投影 projection视图 view剖视图 profile chart标准件 standard component零件图 part drawing装配图 assembly drawing尺⼨标注 size marking技术要求 technical requirements刚度 rigidity内⼒ internal force位移 displacement截⾯ section疲劳极限 fatigue limit断裂 fracture塑性变形 plastic distortion脆性材料 brittleness material刚度准则 rigidity criterion垫圈 washer垫⽚ spacer直齿圆柱齿轮 straight toothed spur gear斜齿圆柱齿轮 helical-spur gear直齿锥齿轮 straight bevel gear运动简图 kinematics sketch齿轮齿条 pinion and rack蜗杆蜗轮 worm and worm gear虚约束 passive constraint曲柄 crank摇杆 rocker凸轮 cams共轭曲线 conjugate curve范成法 generation method定义域 definitional domain值域 range导数\\微分 differential coefficient求导 derivation定积分 definite integral不定积分 indefinite integral曲率 curvature偏微分 partial differential ⽑坯 rough游标卡尺 slide caliper千分尺 micrometer calipers攻丝 tap⼆阶⾏列式 second order determinant逆矩阵 inverse matrix线性⽅程组 linear equations概率 probability随机变量 random variable排列组合 permutation and combination⽓体状态⽅程 equation of state of gas动能 kinetic energy势能 potential energy机械能守恒 conservation of mechanical energy 动量 momentum桁架 truss轴线 axes余⼦式 cofactor逻辑电路 logic circuit触发器 flip-flop脉冲波形 pulse shape数模 digital analogy液压传动机构 fluid drive mechanism机械零件 mechanical parts淬⽕冷却 quench淬⽕ hardening回⽕ tempering调质 hardening and tempering磨粒 abrasive grain结合剂 bonding agent砂轮 grinding wheelback shaft ⽀撑轴 blank determination 胚料展开bottom slide press 下传动式压⼒机 board drop hammer 板落锤brake 煞车 buckle 剥砂⾯camlachie cramp 铸包 casting on flat ?合chamotte sand 烧磨砂 charging hopper 加料漏⽃clearance 间隙 closed-die forging 合模锻造clump 夹紧 clutch 离合器clutch brake 离合器制动器 clutch boss 离合器轮壳clutch lining 离合器覆盖 coil car 带卷升降运输机coil cradle 卷材进料装置 coil reel stand 钢材卷料架column 圆柱 connection screw 连杆调节螺钉core compound 砂⼼黏结剂 counter blow hammer 对击锻锤cradle 送料架 crank 曲柄轴crankless ⽆曲柄式 cross crank 横向曲轴cushion 缓冲 depression 外缩凹孔dial feed 分度送料 die approach 模⼝⾓度die assembly 合模 die cushion 模具缓冲垫die height 冲压闭合⾼度 die life 模具寿命die opening 母模逃孔 die spotting press 调整冲模⽤压⼒机double crank press 双曲柄轴冲床 draght angle 逃料倾斜⾓edging 边锻伸 embedded core 加装砂⼼feed length 送料长度 feed level 送料⾼度filling core 埋⼊砂⼼ filling in 填砂film play 液⾯花纹 fine blanking press 精密下料冲床forging roll 辊锻机 finishing slag 炼後熔渣fly wheel 飞轮 fly wheel brake 飞轮制动器foot press 脚踏冲床 formboard 进模⼝板frame 床⾝机架 friction 摩擦friction brake 摩擦煞车 gap shear 凹⼝剪床gear 齿轮 gib 滑块引导部gripper 夹具 gripper feed 夹持进料gripper feeder 夹紧传送装置 hammer 槌机hand press ⼿动冲床 hand rack pinion press ⼿动齿轮齿条式冲床hand screw press ⼿动螺旋式冲床 hopper feed 料⽃送料idle stage 空站 inching 微调尺⼨isothermal forging 恒温锻造 key clutch 键槽离合器knockout 脱模装置 knuckle mechanic 转向机构land 模具直线⼑⾯部 level ⽔平loader 供料器 unloader 卸料机loop controller 闭回路控制器 lower die 下模micro inching device 微⼨动装置 microinching equipment 微动装置motor 马达 moving bolster 活动⼯作台notching press 冲缺⼝压⼒机 opening 排料逃孔overload protection device 防超载装置 pinch roll 导正滚轮pinion ⼩齿轮 pitch 节距pressfit 压⼊ progressive 连续送料pusher feed 推杆式送料 pusher feeder 料⽚押⽚装置quick die change system 快速换模系统 regrinding 再次研磨releasing 松释动作 reversed blanking 反转下料robot 机器⼈ roll forming machine 辊轧成形roll forming machine 辊轧成形机 roll release 脱辊roller feed 辊式送料 roller leveler 辊式矫直机rotary bender 卷弯成形机 safety guard 安全保护装置scrap cutter 废料切⼑ scrap press 废料冲床seamless forging ⽆缝锻造 separate 分离shave 崩砂 shear angle 剪⾓sheet loader 薄板装料机 shot 单⾏程⼯作shrinkage fit 收缩配合 shut height 闭合⾼度sieve mesh 筛孔 sintering of sand 铸砂烧贴slide balancer 滑动平衡器 slug hole 逃料孔spin forming machine 旋压成形机 spotting 合模stack feeder 堆叠拨送料机 stickness 黏模性straight side frame 冲床侧板 stretcher leveler 拉伸矫直机strip feeder 料材送料装置 stripping pressure 弹出压⼒stroke 冲程 take out device 取料装置toggle press 肘杆式压⼒机 transfer 传送transfer feed 连续⾃动送料装置 turrent punch press 转塔冲床two speed clutch 双速离合器 uncoiler 闭卷送料机unloader 卸载机 vibration feeder 振动送料机wiring press 嵌线卷边机。
机械设计及生产常用词中英文对照表
机械设计及生产常用词中英文对照表Assembly line 组装线Layout 布置图Conveyer 流水线物料板Rivet table 拉钉机Rivet gun 拉钉枪Screw driver 起子Pneumatic screw driver 气动起子worktable 工作桌OOBA 开箱检查fit together 组装在一起fasten 锁紧(螺丝) fixture 夹具(治具) pallet 栈板barcode 条码barcode scanner 条码扫描器fuse together 熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME 制造工程师MT 制造生技cosmetic inspect 外观检查inner parts inspect 内部检查thumb screw 大头螺丝lbs. inch 镑、英寸EMI gasket 导电条front plate 前板rear plate 后板chassis 基座bezel panel 面板power button 电源按键reset button 重置键Hi-pot test of SPS 高源高压测试sheet metal parts 冲件plastic parts 塑胶件material check list 物料检查表work cell 工作间carton 纸箱sub-line 支线left fork 叉车personnel resource department 人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |plein|刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection 终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to 退料scraped |'skr?pid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dei?n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker 锁模器pressure plate=plate pinch压板bolt螺栓administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单location地点present members 出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工cause description原因说明item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子bushing block衬套insert 入块capability能力parameter参数viscosity涂料粘度blanking穿落模dejecting顶固模demagnetization去磁;消磁heat dissipation热传rack上料rinse水洗Chromate铬酸处理Anodize阳性处理seal封孔revision版次good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary function辅助功能sand blasting喷沙derusting machine除锈机degate打浇口dryer烘干机induction感应response=reaction=interaction感应ram连杆concave凸convex凹short射料不足nick缺口speck瑕?? shine亮班gas mark焦痕cold slug冷块gouge沟槽;凿槽patent专利grit沙砾granule=peuet=grain细粒cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化organic solvent有机溶剂liaison联络单volatile挥发性resistance电阻ion离子beacon警示灯coolant冷却液crusher破碎机。
(机械制造行业)机械专业中英文对照-机械专业中英文对照
机械专业英语词汇陶瓷ceramics合成纤维synthetic fibre电化学腐蚀electrochemical corrosion车架automotive chassis悬架suspension转向器redirector变速器speed changer板料冲压sheet metal parts孔加工spot facing machining气动夹紧pneuma lock数学模型mathematical model画法几何descriptive geometry投影projection剖视图profile chart标准件standard component零件图part drawing装配图assembly drawing尺寸标注size marking技术要求technical requirements刚度rigidity内力internal force位移displacement截面section疲劳极限fatigue limit断裂fracture塑性变形plastic distortion脆性材料brittleness material刚度准则rigidity criterion垫片spacer直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear直齿锥齿轮straight bevel gear运动简图kinematic sketch齿轮齿条pinion and rack蜗杆蜗轮worm and worm gear虚约束passive constraint曲柄crank摇杆racker凸轮cams共轭曲线conjugate curve范成法generation method定义域definitional domain值域range导数\\微分differential coefficient求导derivation定积分definite integral不定积分indefinite integral曲率curvature偏微分partial differential毛坯rough游标卡尺slide caliper千分尺micrometer calipers攻丝tap二阶行列式second order determinant逆矩阵inverse matrix线性方程组linear equations概率probability随机变量random variable排列组合permutation and combination气体状态方程equation of state of gas动能kinetic energy势能potential energy机械能守恒conservation of mechanical energy动量momentum桁架truss轴线axes余子式cofactor逻辑电路logic circuit触发器flip-flop脉冲波形pulse shape数模digital analogy液压传动机构fluid drive mechanism机械零件mechanical parts淬火冷却quench淬火hardening回火tempering调质hardening and tempering磨粒abrasive grain结合剂bonding agent砂轮grinding wheel后角clearance angle龙门刨削planing主轴spindle主轴箱headstock卡盘chuck加工中心machining center车刀lathe tool车床lathe钻削镗削bore车削turning磨床grinder基准benchmark钳工locksmith锻forge压模stamping拉床broaching machine拉孔broaching装配assembling铸造found流体动力学fluid dynamics流体力学fluid mechanics加工machining液压hydraulic pressure切线tangent机电一体化mechanotronics mechanical-electrical integration 气压air pressure pneumatic pressure稳定性stability介质medium液压驱动泵fluid clutch液压泵hydraulic pump阀门valve失效invalidation强度intensity载荷load应力stress安全系数safty factor可靠性reliability螺旋helix键spline销pin滚动轴承rolling bearing滑动轴承sliding bearing弹簧spring制动器arrester brake十字结联轴节crosshead联轴器coupling链chain皮带strap精加工finish machining粗加工rough machining变速箱体gearbox casing腐蚀rust氧化oxidation磨损wear耐用度durability随机信号random signal离散信号discrete signal超声传感器ultrasonic sensor集成电路integrate circuit挡板orifice plate残余应力residual stress套筒sleeve扭力torsion冷加工cold machining电动机electromotor汽缸cylinder过盈配合interference fit热加工hotwork摄像头CCD camera倒角rounding chamfer优化设计optimal design工业造型设计industrial moulding design有限元finite element滚齿hobbing插齿gear shaping伺服电机actuating motor铣床milling machine钻床drill machine镗床boring machine步进电机stepper motor丝杠screw rod导轨lead rail组件subassembly可编程序逻辑控制器Programmable Logic Controller PLC 电火花加工electric spark machining电火花线切割加工electrical discharge wire - cutting相图phase diagram热处理heat treatment固态相变solid state phase changes有色金属nonferrous metal陶瓷ceramics合成纤维synthetic fibre电化学腐蚀electrochemical corrosion车架automotive chassis悬架suspension转向器redirector变速器speed changer板料冲压sheet metal parts孔加工spot facing machining气动夹紧pneuma lock数学模型mathematical model画法几何descriptive geometry机械制图Mechanical drawing投影projection视图view剖视图profile chart标准件standard component零件图part drawing装配图assembly drawing尺寸标注size marking技术要求technical requirements刚度rigidity内力internal force位移displacement截面section疲劳极限fatigue limit断裂fracture塑性变形plastic distortion脆性材料brittleness material刚度准则rigidity criterion垫圈washer垫片spacer直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear直齿锥齿轮straight bevel gear运动简图kinematic sketch齿轮齿条pinion and rack蜗杆蜗轮worm and worm gear虚约束passive constraint曲柄crank摇杆racker凸轮cams共轭曲线conjugate curve范成法generation method定义域definitional domain值域range导数\\微分differential coefficient求导derivation定积分definite integral不定积分indefinite integral曲率curvature偏微分partial differential毛坯rough游标卡尺slide caliper千分尺micrometer calipers攻丝tap二阶行列式second order determinant逆矩阵inverse matrix线性方程组linear equations概率probability随机变量random variable排列组合permutation and combination气体状态方程equation of state of gas动能kinetic energy势能potential energy机械能守恒conservation of mechanical energy 动量momentum桁架truss轴线axes余子式cofactor逻辑电路logic circuit触发器flip-flop脉冲波形pulse shape数模digital analogy液压传动机构fluid drive mechanism机械零件mechanical parts淬火冷却quench淬火hardening回火tempering调质hardening and tempering磨粒abrasive grain结合剂bonding agent砂轮grinding wheelConveyer 流水线物料板Rivet table 拉钉机Screw driver 起子Pneumatic screw driver 气动起子worktable 工作桌OOBA 开箱检查fit together 组装在一起fasten 锁紧(螺丝)fixture 夹具(治具)pallet 栈板barcode 条码barcode scanner 条码扫描器fuse together 熔合fuse machine热熔机ME 制造工程师MT 制造生技cosmetic inspect 外观检查inner parts inspect 内部检查thumb screw 大头螺丝lbs. inch 镑、英寸EMI gasket 导电条front plate 前板rear plate 后板chassis 基座bezel panel 面板power button 电源按键reset button 重置键Hi-pot test of SPS 高源高压测试Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件plastic parts 塑胶件SOP 制造作业程序material check list 物料检查表work cell 工作间trolley 台车carton 纸箱sub-line 支线left fork 叉车personnel resource department 人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |plein|刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |\\'skr?pid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |\\' ksi\\'dei?n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单location地点present members出席人员conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表model机锺work order工令revision版次production control confirmation生产确认approved by核准stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工cause description原因说明prepared by制表notes说明year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机阿基米德蜗杆Archimedes worm安全系数safety factor; factor of safety 安全载荷safe load凹面、凹度concavity扳手wrench板簧flat leaf spring半圆键woodruff key变形deformation摆杆oscillating bar摆动从动件oscillating follower摆动从动件凸轮机构cam with oscillating follower 摆动导杆机构oscillating guide-bar mechanism 摆线齿轮cycloidal gear摆线齿形cycloidal tooth profile摆线运动规律cycloidal motion摆线针轮cycloidal-pin wheel包角angle of contact保持架cage背对背安装back-to-back arrangement背锥back cone ；normal cone背锥角back angle背锥距back cone distance比例尺scale比热容specific heat capacity闭式链closed kinematic chain闭链机构closed chain mechanism臂部arm变频器frequency converters变频调速frequency control of motor speed变速speed change变速齿轮change gear change wheel变位齿轮modified gear变位系数modification coefficient标准齿轮standard gear标准直齿轮standard spur gear表面质量系数superficial mass factor表面传热系数surface coefficient of heat transfer 表面粗糙度surface roughness并联式组合combination in parallel并联机构parallel mechanism并联组合机构parallel combined mechanism并行工程concurrent engineering并行设计concurred design, CD不平衡相位phase angle of unbalance不平衡imbalance (or unbalance)不平衡量amount of unbalance不完全齿轮机构intermittent gearing波发生器wave generator波数number of waves补偿compensation参数化设计parameterization design, PD残余应力residual stress操纵及控制装置operation control device槽轮Geneva wheel槽轮机构Geneva mechanism ；Maltese cross槽数Geneva numerate槽凸轮groove cam侧隙backlash差动轮系differential gear train差动螺旋机构differential screw mechanism差速器differential常用机构conventional mechanism; mechanism in common use 车床lathe承载量系数bearing capacity factor承载能力bearing capacity成对安装paired mounting尺寸系列dimension series齿槽tooth space齿槽宽spacewidth齿侧间隙backlash齿顶高addendum齿顶圆addendum circle齿根高dedendum齿根圆dedendum circle齿厚tooth thickness齿距circular pitch齿宽face width齿廓tooth profile齿廓曲线tooth curve齿轮gear齿轮变速箱speed-changing gear boxes齿轮齿条机构pinion and rack齿轮插刀pinion cutter; pinion-shaped shaper cutter齿轮滚刀hob ,hobbing cutter齿轮机构gear齿轮轮坯blank齿轮传动系pinion unit齿轮联轴器gear coupling齿条传动rack gear齿数tooth number齿数比gear ratio齿条插刀rack cutter; rack-shaped shaper cutter齿形链、无声链silent chain齿形系数form factor齿式棘轮机构tooth ratchet mechanism插齿机gear shaper重合点coincident points重合度contact ratio冲床punch传动比transmission ratio, speed ratio传动装置gearing; transmission gear传动系统driven system传动角transmission angle传动轴transmission shaft串联式组合combination in series串联式组合机构series combined mechanism串级调速cascade speed control创新innovation creation创新设计creation design垂直载荷、法向载荷normal load唇形橡胶密封lip rubber seal磁流体轴承magnetic fluid bearing从动带轮driven pulley从动件driven link, follower从动件平底宽度width of flat-face从动件停歇follower dwell从动件运动规律follower motion从动轮driven gear粗线bold line粗牙螺纹coarse thread大齿轮gear wheel打包机packer打滑slipping带传动belt driving带轮belt pulley带式制动器band brake单列轴承single row bearing单向推力轴承single-direction thrust bearing单万向联轴节single universal joint单位矢量unit vector当量齿轮equivalent spur gear; virtual gear当量齿数equivalent teeth number; virtual number of teeth 当量摩擦系数equivalent coefficient of friction当量载荷equivalent load导数derivative倒角chamfer导热性conduction of heat导程lead导程角lead angle等加等减速运动规律parabolic motion; constant acceleration and deceleration motion 等速运动规律uniform motion; constant velocity motion等径凸轮conjugate yoke radial cam等宽凸轮constant-breadth cam等效构件equivalent link等效力equivalent force等效力矩equivalent moment of force等效量equivalent等效质量equivalent mass等效转动惯量equivalent moment of inertia等效动力学模型dynamically equivalent model底座chassis低副lower pair点划线chain dotted line（疲劳）点蚀pitting垫圈gasket垫片密封gasket seal碟形弹簧belleville spring顶隙bottom clearance定轴轮系ordinary gear train; gear train with fixed axes动力学dynamics动密封kinematical seal动能dynamic energy动力粘度dynamic viscosity动力润滑dynamic lubrication动平衡dynamic balance动平衡机dynamic balancing machine动态特性dynamic characteristics动态分析设计dynamic analysis design动压力dynamic reaction动载荷dynamic load端面transverse plane端面参数transverse parameters端面齿距transverse circular pitch端面齿廓transverse tooth profile端面重合度transverse contact ratio端面模数transverse module端面压力角transverse pressure angle对称循环应力symmetry circulating stress对心滚子从动件radial (or in-line ) roller follower对心直动从动件radial (or in-line ) translating follower对心移动从动件radial reciprocating follower对心曲柄滑块机构in-line slider-crank (or crank-slider) mechanism 多列轴承multi-row bearing多楔带poly V-belt多项式运动规律polynomial motion多质量转子rotor with several masses惰轮idle gear额定寿命rating life额定载荷load ratingII 级杆组dyad发生线generating line发生面generating plane法面normal plane法面参数normal parameters法面齿距normal circular pitch法面模数normal module法面压力角normal pressure angle法向齿距normal pitch法向齿廓normal tooth profile法向直廓蜗杆straight sided normal worm法向力normal force反馈式组合feedback combining反向运动学inverse ( or backward) kinematics反转法kinematic inversion反正切Arctan范成法generating cutting仿形法form cutting方案设计、概念设计concept design, CD防振装置shockproof device飞轮flywheel飞轮矩moment of flywheel非标准齿轮nonstandard gear非接触式密封non-contact seal非周期性速度波动aperiodic speed fluctuation非圆齿轮non-circular gear粉末合金powder metallurgy分度线reference line; standard pitch line分度圆reference circle; standard (cutting) pitch circle分度圆柱导程角lead angle at reference cylinder分度圆柱螺旋角helix angle at reference cylinder分母denominator分子numerator分度圆锥reference cone; standard pitch cone 分析法analytical method封闭差动轮系planetary differential复合铰链compound hinge复合式组合compound combining复合轮系compound (or combined) gear train 复合平带compound flat belt复合应力combined stress复式螺旋机构Compound screw mechanism复杂机构complex mechanism杆组Assur group干涉interference刚度系数stiffness coefficient刚轮rigid circular spline钢丝软轴wire soft shaft刚体导引机构body guidance mechanism刚性冲击rigid impulse (shock)刚性转子rigid rotor刚性轴承rigid bearing刚性联轴器rigid coupling高度系列height series高速带high speed belt高副higher pair格拉晓夫定理Grashoff`s law根切undercutting公称直径nominal diameter高度系列height series功work工况系数application factor工艺设计technological design工作循环图working cycle diagram工作机构operation mechanism工作载荷external loads工作空间working space工作应力working stress工作阻力effective resistance工作阻力矩effective resistance moment公法线common normal line公共约束general constraint公制齿轮metric gears功率power功能分析设计function analyses design共轭齿廓conjugate profiles共轭凸轮conjugate cam构件link鼓风机blower固定构件fixed link; frame固体润滑剂solid lubricant关节型操作器jointed manipulator惯性力inertia force惯性力矩moment of inertia ,shaking moment 惯性力平衡balance of shaking force惯性力完全平衡full balance of shaking force惯性力部分平衡partial balance of shaking force 惯性主矩resultant moment of inertia惯性主失resultant vector of inertia冠轮crown gear广义机构generation mechanism广义坐标generalized coordinate轨迹生成path generation轨迹发生器path generator滚刀hob滚道raceway滚动体rolling element滚动轴承rolling bearing滚动轴承代号rolling bearing identification code 滚针needle roller滚针轴承needle roller bearing滚子roller滚子轴承roller bearing滚子半径radius of roller滚子从动件roller follower滚子链roller chain滚子链联轴器double roller chain coupling滚珠丝杆ball screw滚柱式单向超越离合器roller clutch过度切割undercutting函数发生器function generator函数生成function generation含油轴承oil bearing耗油量oil consumption耗油量系数oil consumption factor赫兹公式H. Hertz equation合成弯矩resultant bending moment合力resultant force合力矩resultant moment of force横坐标abscissa互换性齿轮interchangeable gears花键spline滑键、导键feather key滑动轴承sliding bearing滑动率sliding ratio滑块slider环面蜗杆toroid helicoids worm环形弹簧annular spring缓冲装置shocks; shock-absorber灰铸铁grey cast iron回程return回转体平衡balance of rotors混合轮系compound gear train积分integrate机电一体化系统设计mechanical-electrical integration system design 机构mechanism机构分析analysis of mechanism机构平衡balance of mechanism机构学mechanism机构运动设计kinematic design of mechanism机构运动简图kinematic sketch of mechanism机构综合synthesis of mechanism机构组成constitution of mechanism机架frame, fixed link机架变换kinematic inversion机器machine机器人robot机器人操作器manipulator机器人学robotics技术过程technique process技术经济评价technical and economic evaluation技术系统technique system机械machinery机械创新设计mechanical creation design, MCD机械系统设计mechanical system design, MSD机械动力分析dynamic analysis of machinery机械动力设计dynamic design of machinery机械动力学dynamics of machinery机械的现代设计modern machine design机械系统mechanical system机械利益mechanical advantage机械平衡balance of machinery机械设计machine design; mechanical design机械特性mechanical behavior机械调速mechanical speed governors机械效率mechanical efficiency机械原理theory of machines and mechanisms机械运转不均匀系数coefficient of speed fluctuation机械无级变速mechanical stepless speed changes基础机构fundamental mechanism基本额定寿命basic rating life基于实例设计case-based design,CBD基圆base circle基圆半径radius of base circle基圆齿距base pitch基圆压力角pressure angle of base circle基圆柱base cylinder基圆锥base cone急回机构quick-return mechanism急回特性quick-return characteristics急回系数advance-to return-time ratio急回运动quick-return motion棘轮ratchet棘轮机构ratchet mechanism棘爪pawl极限位置extreme (or limiting) position极位夹角crank angle between extreme (or limiting) positions计算机辅助设计computer aided design, CAD计算机辅助制造computer aided manufacturing, CAM计算机集成制造系统computer integrated manufacturing system, CIMS 计算力矩factored moment; calculation moment计算弯矩calculated bending moment加权系数weighting efficient加速度acceleration加速度分析acceleration analysis加速度曲线acceleration diagram尖点pointing; cusp尖底从动件knife-edge follower间隙backlash间歇运动机构intermittent motion mechanism减速比reduction ratio减速齿轮、减速装置reduction gear减速器speed reducer减摩性anti-friction quality渐开螺旋面involute helicoid渐开线齿廓involute profile渐开线齿轮involute gear渐开线发生线generating line of involute渐开线方程involute equation渐开线函数involute function渐开线蜗杆involute worm渐开线压力角pressure angle of involute渐开线花键involute spline简谐运动simple harmonic motion键key键槽keyway交变应力repeated stress交变载荷repeated fluctuating load交叉带传动cross-belt drive交错轴斜齿轮crossed helical gears胶合scoring角加速度angular acceleration角速度angular velocity角速比angular velocity ratio角接触球轴承angular contact ball bearing角接触推力轴承angular contact thrust bearing 角接触向心轴承angular contact radial bearing 角接触轴承angular contact bearing铰链、枢纽hinge校正平面correcting plane接触应力contact stress接触式密封contact seal阶梯轴multi-diameter shaft结构structure结构设计structural design截面section节点pitch point节距circular pitch; pitch of teeth节线pitch line节圆pitch circle节圆齿厚thickness on pitch circle节圆直径pitch diameter节圆锥pitch cone节圆锥角pitch cone angle解析设计analytical design紧边tight-side紧固件fastener径节diametral pitch径向radial direction径向当量动载荷dynamic equivalent radial load径向当量静载荷static equivalent radial load径向基本额定动载荷basic dynamic radial load rating 径向基本额定静载荷basic static radial load tating径向接触轴承radial contact bearing径向平面radial plane径向游隙radial internal clearance径向载荷radial load径向载荷系数radial load factor径向间隙clearance静力static force静平衡static balance静载荷static load静密封static seal局部自由度passive degree of freedom矩阵matrix矩形螺纹square threaded form锯齿形螺纹buttress thread form矩形牙嵌式离合器square-jaw positive-contact clutch 绝对尺寸系数absolute dimensional factor绝对运动absolute motion绝对速度absolute velocity均衡装置load balancing mechanism抗压强度compression strength开口传动open-belt drive开式链open kinematic chain开链机构open chain mechanism可靠度degree of reliability可靠性reliability可靠性设计reliability design, RD空气弹簧air spring空间机构spatial mechanism空间连杆机构spatial linkage空间凸轮机构spatial cam空间运动副spatial kinematic pair空间运动链spatial kinematic chain空转idle宽度系列width series框图block diagram雷诺方程Reynolds‘s equation离心力centrifugal force离心应力centrifugal stress离合器clutch离心密封centrifugal seal理论廓线pitch curve理论啮合线theoretical line of action隶属度membership力force力多边形force polygon力封闭型凸轮机构force-drive (or force-closed) cam mechanism 力矩moment力平衡equilibrium力偶couple力偶矩moment of couple连杆connecting rod, coupler连杆机构linkage连杆曲线coupler-curve连心线line of centers链chain链传动装置chain gearing链轮sprocket sprocket-wheel sprocket gear chain wheel联组V 带tight-up V belt联轴器coupling shaft coupling两维凸轮two-dimensional cam临界转速critical speed六杆机构six-bar linkage龙门刨床double Haas planer轮坯blank轮系gear train螺杆screw螺距thread pitch螺母screw nut螺旋锥齿轮helical bevel gear螺钉screws螺栓bolts螺纹导程lead螺纹效率screw efficiency螺旋传动power screw螺旋密封spiral seal螺纹thread (of a screw)螺旋副helical pair螺旋机构screw mechanism螺旋角helix angle螺旋线helix ,helical line绿色设计green design design for environment马耳他机构Geneva wheel Geneva gear马耳他十字Maltese cross脉动无级变速pulsating stepless speed changes脉动循环应力fluctuating circulating stress脉动载荷fluctuating load铆钉rivet迷宫密封labyrinth seal密封seal密封带seal belt密封胶seal gum密封元件potted component密封装置sealing arrangement面对面安装face-to-face arrangement面向产品生命周期设计design for product`s life cycle, DPLC 名义应力、公称应力nominal stress模块化设计modular design, MD模块式传动系统modular system模幅箱morphology box模糊集fuzzy set模糊评价fuzzy evaluation模数module摩擦friction摩擦角friction angle摩擦力friction force摩擦学设计tribology design, TD摩擦阻力frictional resistance摩擦力矩friction moment摩擦系数coefficient of friction摩擦圆friction circle磨损abrasion wear; scratching末端执行器end-effector目标函数objective function耐腐蚀性corrosion resistance耐磨性wear resistance挠性机构mechanism with flexible elements挠性转子flexible rotor内齿轮internal gear内齿圈ring gear内力internal force内圈inner ring能量energy能量指示图viscosity逆时针counterclockwise (or anticlockwise)啮出engaging-out啮合engagement, mesh, gearing啮合点contact points啮合角working pressure angle啮合线line of action啮合线长度length of line of action啮入engaging-in牛头刨床shaper凝固点freezing point; solidifying point扭转应力torsion stress扭矩moment of torque扭簧helical torsion spring诺模图NomogramO 形密封圈密封O ring seal盘形凸轮disk cam盘形转子disk-like rotor抛物线运动parabolic motion疲劳极限fatigue limit疲劳强度fatigue strength偏置式offset偏( 心) 距offset distance偏心率eccentricity ratio偏心质量eccentric mass偏距圆offset circle偏心盘eccentric偏置滚子从动件offset roller follower偏置尖底从动件offset knife-edge follower偏置曲柄滑块机构offset slider-crank mechanism 拼接matching评价与决策evaluation and decision频率frequency平带flat belt平带传动flat belt driving平底从动件flat-face follower平底宽度face width平分线bisector平均应力average stress平均中径mean screw diameter平均速度average velocity平衡balance平衡机balancing machine平衡品质balancing quality平衡平面correcting plane平衡质量balancing mass平衡重counterweight平衡转速balancing speed平面副planar pair, flat pair平面机构planar mechanism平面运动副planar kinematic pair平面连杆机构planar linkage平面凸轮planar cam平面凸轮机构planar cam mechanism平面轴斜齿轮parallel helical gears普通平键parallel key其他常用机构other mechanism in common use起动阶段starting period启动力矩starting torque气动机构pneumatic mechanism奇异位置singular position起始啮合点initial contact , beginning of contact气体轴承gas bearing千斤顶jack嵌入键sunk key强迫振动forced vibration切齿深度depth of cut曲柄crank曲柄存在条件Grashoff`s law曲柄导杆机构crank shaper (guide-bar) mechanism曲柄滑块机构slider-crank (or crank-slider) mechanism 曲柄摇杆机构crank-rocker mechanism曲齿锥齿轮spiral bevel gear曲率curvature曲率半径radius of curvature曲面从动件curved-shoe follower曲线拼接curve matching曲线运动curvilinear motion曲轴crank shaft驱动力driving force驱动力矩driving moment (torque)全齿高whole depth权重集weight sets球ball球面滚子convex roller球轴承ball bearing球面副spheric pair球面渐开线spherical involute球面运动spherical motion球销副sphere-pin pair球坐标操作器polar coordinate manipulator燃点spontaneous ignition热平衡heat balance; thermal equilibrium人字齿轮herringbone gear冗余自由度redundant degree of freedom柔轮flexspline柔性冲击flexible impulse; soft shock柔性制造系统flexible manufacturing system; FMS柔性自动化flexible automation润滑油膜lubricant film润滑装置lubrication device润滑lubrication润滑剂lubricant三角形花键serration spline三角形螺纹V thread screw三维凸轮three-dimensional cam三心定理Kennedy`s theorem砂轮越程槽grinding wheel groove砂漏hour-glass少齿差行星传动planetary drive with small teeth difference 设计方法学design methodology设计变量design variable设计约束design constraints深沟球轴承deep groove ball bearing生产阻力productive resistance升程rise升距lift实际廓线cam profile十字滑块联轴器double slider coupling; Oldham‘s coupling 矢量vector输出功output work输出构件output link输出机构output mechanism输出力矩output torque输出轴output shaft输入构件input link数学模型mathematic model实际啮合线actual line of action双滑块机构double-slider mechanism, ellipsograph双曲柄机构double crank mechanism双曲面齿轮hyperboloid gear双头螺柱studs双万向联轴节constant-velocity (or double) universal joint 双摇杆机构double rocker mechanism双转块机构Oldham coupling双列轴承double row bearing双向推力轴承double-direction thrust bearing。
机械专业英语和翻译
Programmable
Logic Controller PLC 电火花加工 electric spark machining 电火花线切割加工 electrical discharge
wire - cutting 相图 phase diagram 热处理 heat treatment
固态相变 solid state phase changes
主运动方向 direction of main movement 进给方向 direction of feed 进给运动 feed movement 合成进给运动 resultant movement of feed 合成切削运动 resultant movement of
cutting 合成切削运动方向 direction of resultant
淬火 hardening 回火 tempering
调质 hardening and tempering 磨粒 abrasive grain 结合剂 bonding agent
砂轮 grinding wheel
机械零件 mechanical parts 淬火冷却 quench
淬火 hardening 回火 tempering
车刀 车床 钻削
lathe tool lathe 镗削 bore
车削 turning 磨床 grinder
基准 benchmark
钳工 locksmith 锻 forge 压模 stamping 焊 weld 拉床 broaching machine 拉孔 broaching 装配 assembling
孔加工 spot facing machining 车间 workshop
工程技术人员 engineer
机械加工外文翻译、中英文翻译、机械类外文文献翻译
机械加工外文翻译、中英文翻译、机械类外文文献翻译The engine lathe is an old but still useful metal removal machine with many desirable attributes。
While it is no longer commonlyXXX。
In today's n shops。
it has largely been XXX。
turret lathes。
and automatic XXX of single-point tooling for maximum metal removal。
and the use of form tools for finished products that are on par with the fastest processing XXX.When it XXX for the engine lathe。
it largely depends on the skill of the operator。
Design XXX part for n。
it is XXX.XXX cutting tools。
XXX ns。
as the machine can perform these ns in one setup。
They are also capable of producing parts with high n and accuracy。
XXX industries.Now more than ever。
n machining XXX of a specific method。
the XXX.When designing for low quantities。
such as 100 or 200 parts。
it is most cost-effective to use a XXX。
designers should aim to minimize the number of ns required.Another n for n XXX。
机床刀具设计机械类毕业设计外文文献翻译中英文翻译
英语原文：Design Of Tool Machine PropResearch significanceThe original knife machine control procedures are designed individually, not used tool management system, features a single comparison, the knife only has to find the tool knife, knife positioning the shortest path, axis tool change, but does not support large-scale tool.Automatic knife in the knife election, in the computer memory knife-election on the basis of using the Siemens 840 D features, and the election procedures knife more concise, and complete the space Daotao View. ATC use the knife rapid completion of STEP-7 programming, and have been tested in practice. In the positioning of the knife, PLC controlled modular design method, which future production of similar machines will be very beneficial, it is easy to use its other machine. Automatic tool change systems will be faster growth, reduced tool change time, increase the positioning accuracy tool is an important means to help NC technology development.Tool and inventory components of modern production is an important link in the management, especially for large workshop management. The traditional way of account management, and low efficiency, high error rate, and not sharing information and data, tools and the use of state can not track the life cycle, are unable to meet the current information management needs. With actual production, we have to establish a workshop tool for the three-dimensional tool storage system to meet the knife workshop with auxiliary storage and management needs.The system uses optimization technology, a large number of computer storage inventory information, timely, accurate, and comprehensive tool to reflect the inventory situation. The entire system uses a graphical interface, man-machine dialogue tips from the Chinese menu, select various functions can be realized and the importation of all kinds of information. Management system using online help function. Through the workshop management, network management and sharing of information. Have automated inventory management, warehousing management tool, a tool for the management and statistical functions.1.System components and control structureThe entire system, including the structure and electrical machinery control systems.1.1.1Mechanical structure and working principleTool from the stent, drive, drive system, Turret, shielding, control system, and electrical components. Support from the column, beam, the upper and lower guide Central track, and track support component.1) Drive for the system chosen VVVF method. Cone used brake motors, with VVVF by Cycloidreducer through sprocket drive.2) Drag a variable frequency drive system and control technology. VVVF adopted, will speed drive shaft in the normal range adjustment to control the speed rotary turret to 5 ~ 30mm in, the drive shaft into two, two under through sprocket, the two profiled rollers Chain driven rotating shelves. Expansion chain adopted by the thread tight regulation swelling, swelling the regular way. - Conditioned, under the same chain-of-conditioning, so that the chain of uniform.3) Turret and shields the entire total of 14 independent Turret. 13 of them as a socket-Turret, as a drawer-Turret, each Turret back through the pin and, under the conveyor chain link chain plate, installed at the bottom roller, chain driven rotating turret rotation along the track. Outlet-Turret and BT50-BT40 Turret Turret two kinds of forms. To strengthen management, security, landscaping modeling, shelf peripherals and shields. Turret-drawer drawer placed at six other Des V oeux a knife, can be categorized with some of knife auxiliary equipment, such as bits, such as turning tools.1.1.2.Electrical Control SystemThis tool storage systems is the main electrical control their shelves for operational control and position control. Operational control equipment, including operation of the start of braking control. Position Control is the main location and address of the shelves for testing. Control system as shown in Figure 1.图 1 Tool Control System for the1) Electric Transmission horizontal rotary tool storage systems are the mechanical movements are repeated short-term work system. And the run-time system needs some speed, speed transmission needs, the system will use VVVF method can be used simple structure, reliable operation of the motor and frequency inverter.2) Control of the system is divided into two kinds of manual control and automatic control, manual control as a general reserve and debugging methods of work; ways to the system control computer (IPC) and the control unit (inverter contactor , etc.) consisting of a control system.3) location and positioning accuracy of the system automatically identify the site and location using a detection device as proximity switches, relays through the plate-point isolation and the number plate recorded close to the switching signal acquisition and operation of Hutchison with a Optimal Path addressable identify the current location and shelves of the purpose of the shelf location. In order to enable a more accurate positioning system, adopted two photoelectric switches, to detect the two shelves of the two films.1.2.The functions of the knifeknife The is the role of reserves a certain number of tools, machine tool spindle in hand to achieve the fungibility a disc cutter knife is the type of library, the chain knives, and other means, in the form of the knife and capacity according to the Machine Tool to determine the scope of the process.mon typesThe knife is a tool storage devices, the common knife mainly in the following forms:(1) the turret knifeIncluding the first level turret vertical turret and the first two, see Figure 2.6 a) and b):(2) the disc cutterDisc knife in the library with discoid knife, cutting tool along See how vertical arrangement (including radial and axial from knife from knife), along See how radial array into acute or arranged in the form of the knife. Simple, compact, more applications, but are ring-cutter, low utilization of space. Figure 2.7 a) to c). If the knife storage capacity must be increased to increase the diameter of the knife, then the moment of inertia also increased correspondingly, the election campaign long knife. Tool number not more than 32 general. Cutter was multi-loop order of the space utilization knife, but inevitably given the knife from complex institutions,applicable to the restricted space Machine Tool storage capacity and more occasions. Two-disc structure is two smaller capacity knife on both sides of the sub-spindle place, more compactlayout, the number of certificates corresponding increase knife, apply to small and medium-sized processing center.(3) the chain knifeIncluding single-and multi-ring chain ring chain, chain link can take many forms change, see Figure 2.8 a) to c), thebasic structure shown inFigure 2. 8 doFeatures: knife apply tothe larger capacity of theoccasion, the space of thesmall number ofgenerally applicable tothe tool in the 30-120.Only increase the lengthof the chain tool will increase the number should not be increased circumferential speed of itsmoment of inertia of the knife does not increase the disc as large.(4) linear combination knife and the knife libraryThe linear knife simple structure in Figure 2.9, tool single order, the capacity of small knife, used for CNC lathe and drill press on. Because the location of fixed knife, ATC completed action by the spindle without manipulator. The cutter knife is generally the turret combination turret with a combination of the disc cutter knife and the chain combination. Every single knife the knife certificates of smaller, faster tool change. There are also some intensive drum wheel, and the lattice-type magazine for the knife, the knife-intensive though. Small footprint, but because of structural constraints, basically not used for single processing center, the concentration used for FMS for the knife system.1.4 Tool storage capacityTool storage capacity of the first to consider the needs of processing, from the use of point of view, generally 10 to 40 knives, knife will be the utilization of the high, and the structure iscompact.1.5 Tool options(1) choose to order processing tool according to the order, followed Add to the knife every knife in the Block. Each tool change, the order of rotation of a cutter knife on location, and remove the need knives, has been used by the cutter knife can be returned to the original Block, can also order Add Block, a knife. However, as the knife in the tool in different processes can not be repeated use of the knife must increase the capacity and lower utilization rate.(2) most of the arbitrary choice of the current system of using arbitrary NC election knives, divided into Daotao coding, coding and memory-cutter, three. Daotao coding tool code or knives or Daotao need to install the code used to identify, in accordance with the general principle of binary coding coding. Tool knife election coding method uses a special knife handle structure, and each of the coding tool. Each of the tool has its own code, thereby cutting tool can be in different processes repeatedly used, not to replace the tool back at the original knife, the knife capacity can be reduced accordingly. Memory-election this paper knife, in this way can knives and knife in the position corresponding to the Daotao memory of the PLC in the NC system, no matter which tool on the Inner knife, tool information is always there in mind, PLC . On the knife with position detection devices, will be the location of each Daotao. This tool can be removed and sent back to arbitrary. On the knife is also a mechanical origin, every election, the nearest knife selection.1.6.Control of the knife(1) the knife as a system to control the positioning axis. In the ladder diagram in accordance with the instructions for computing T code comparison of the output angle and speed of instructions to the knife the knife servo drive servo motor. Tool storage capacity, rotation speed, and / deceleration time, and other system parameters can be set in such a manner free from any outside influence positioning accurate and reliable but the cost is higher.(2) knife from the hydraulic motor drives, fast / slow the points, with proximity switches count and positioning. In comparison ladder diagram of the current storage system knife (knife spindle) and goals knife (pre-knife) and computing, then output rotation instructions, judging by the shortest path rotation in place. This approach requires sufficient hydraulic power and electromagnetic valve knife the rotational speed can be adjusted through the throttle. But over time may be oily hydraulic, oil temperature and environmental factors impact the change in velocity and accuracy. Not generally used in large and medium-sized machine tool change frequently.(3) the knife from AC asynchronous motor driven cam mechanism (Markov institutions), with proximity switches count, which means stable operation, and generally accurate and reliablepositioning cam used in conjunction with a mechanical hand, A TC fast-positioning.2. ATC, the main types, characteristics, and the scope of application 2.1 Auto Rotary ToolRotary Tool automatically onthe use of CNC machine tool is asimple installation of automatic toolchange, the Quartet and 47.60 TurretTool various forms, such as rotaryturret were installed on four, six ormore of the Tool , NC instructions byATC. Rotary Tool has two verticaland horizontal, relatively simplestructure, applicable to economicCNC lathe.Rotary Tool in the structure musthave good strength and stiffness,resistance to bear rough Cutting Toolin the cutting force and reduce therole of deformation and improveprocessing accuracy. Rotating Toolto choose reliable positioningprogramme structure and reasonable position, in order to ensure that each rotary turret to a higher position after repeated positioning accuracy (typically 0.001 to 0.005mm). Figure 2.1 shows the spiral movements of the Quartet Turret.Auto Rotary Tool in the simplest of ATC, is 180 º rotary ATC devices, as shown in Figure 2.2 ATC instructions received, the machine control system put ATC spindle control to the designated location at the same time, the tool movement to the appropriate location, ATC, with the rotary axis and at the same time, the knives matching tool; drawbars from Spindle Cutting Tools rip, ATC, will be the tool from their position removed; ATC, 180 º rotary tool spindle and the tool and tool away; A TC, the Rotary At the same time, the tool refocusing its position to accept Spindle removed from the cutting tool; Next, ATC, will be replaced with the cutter knives were unloaded into the spindle and tool: Finally, back to the original ATC, "standby" position. At this point, ATC completed procedures to continue to run. This ATC, the main advantage ofsimple structure, the less movement, fast tool change. The main disadvantage is that knives must be kept in parallel with the axis of the plane, and after the home side compared to the tool, chip and liquid-cutting knife into the folder, it is necessary to the tool plus protection. Cone knife folder on the chip will cause A TC error, or even damage knife folders, and the possibility of spindle. Some processing centre at the transfer, and the tool side. When the ATC command is called, the transfer-cutter knives will be removed, the machine go forward, and positioning with the ATC, in line with the position. 180 º "Rotary ATC devices can be used horizontal machine, can also be used for vertical machining centers.2. 2 ATC head-turret installedWith rotating CNC machine tool often used such ATC devices, with a few turret head spindle, each with a spindle on both knives, the first tower interim process can be automatic tool change-realization. The advantage is simple structure, tool change time is short, only about 2 s. However, due to spatial constraints, the number of spindle can not be too much, usually only apply to processes less, not to high precision machine tools, such as the NC drill, such as CNC milling machine. In recent years there has been a mechanical hand and the turret head with a knife for the automatic tool change ATC devices, as shown in Figure 2.3. It is in fact a turret head ATC, and the knife-ATC device combination. The principle is as follows:5 turret on the first two tool spindle 3 and 4, when using the tool spindle 4 processing tool, the manipulator 2 will be the next step to the need for the tool does not work on the tool spindle 3 until after the completion of this process , the first rotary turret 180 º, A TC completed. ATC most of their time and processing time coincidence, the only real tool change time turret transposition of the first time, this approach mainly used for ATC and NC NC drilling file bed. 2. 3.Daidao system for the automatic tool changeFigure 2.4 shows the knife and the whole machine tool CNC machine tools for the appearance of Fig.Figure 2.5 shows the knife and split-type machine to the appearance of CNC machine tool plans.At this point, knife storage capacity, a heavier tool can, and often additional transport unit to complete the knife between the spindle and cutting tool transport.Daidao the knife from the ATC, the election knives, automatic loading and unloading machine tool and tool exchange institutions (manipulator), composed of four parts, used widely.Tool Automatic Tool Change the manipulator system, the whole process more complicated ATC. We must first used in the processing of all installed in the standard tool on the knife handle in the machine outside the pre-size, according to a certain way Add to the knife. ATC, selected first in the knife knife, and then from ATC, from the knife from the knife or spindle, exchange, the new knife into the spindle, the old knife back into the knife.ATC, as the former two knives to accommodate a limited number can not be too many, can notmeet the needs of complex parts machining, CNC machine tool Automatic Tool Change Daidao the use of the automatic tool change devices. The knife has more capacity, both installed in the spindle box side or above. As for the automatic tool change Daidao device CNC machine tool spindle box only a spindle, spindle components to high stiffness to meet the machining requirements. The number of establishments in larger knife, which can meet the more complex parts of the machining processes, significantly improving productivity. Daidao system for the automatic tool change applied to drilling centres and CNC machining centers. The comparison drawn Daidao automatic tool change system is the most promising.3.PLC control of the knife random mode of election3. 1Common methods of automatic election knifeAutomatic control of the knife CNC refers to the system after the implementation of user instructions on the knife library automation process, including the process to find knives and automatic tool change [(63,71]. CNC Machining Center device (CNC) directive issued by the election knife , a knife, the tool required to take the knife position, said the election automatic knife. automatically elected knife There are two ways: random sequence election knives and knife election method.3.1.1 order election knifeTool Selection order is the process tool according to the sequence of the insert knife, the use of knives in order to take place, used knives back at the original knife, can also order Add Block, a knife. In this way, no need Tool identification devices, and drive control is a relatively simple, reliable and can be used directly from the points of the knife machinery to achieve. But the knives in each of the tool in different processes can not be reused, if the tool is installed in accordance with the order of the knife, there will be serious consequences. The need to increase the number of knives and knife the capacity of the tool and reduce the utilization of the knife.3.1.2Random election knifeRandom election under the knife is arbitrary instructions to select the required tools, then there must be tool identification devices. Tool knife in the library do not have the processing in accordance with the order of the workpiece can be arbitrary storage. Each of the tool (or knifeblocks) are for a code, automatic tool change, the rotary cutter, every tool have been the "tool identification device" acceptable identification. When CNC tool code and the code in line with directives of the tool selected, the rotary cutter knives will be sent to the ATC position, waiting to grab manipulator. Random knife election is the advantage of the cutter knife in the order has nothing to do with the processing sequence, the same tool can be used repeatedly. Therefore, the relatively small number of knives, knife the corresponding smaller. Random elections knife on the tool must be coded to identify. There are three main coding.1. Tool coding. Adopt special knife handle structure coding, the drawbars on the knife handle back-end packages such as spacing of the coding part of the lock-nut fixed. Coding diameter ring diameter of a size two, respectively, said that binary "1" and "0" to the two rings are different, can be a series of code. For example, there are six small diameter of the ring can be made to distinguish between 63 (26-1 = 63) of the coding tool. All of 0 normally not allowed to use the code, to avoid the cutter knife Block did not confuse the situation.2. Knife Block coding. On the knife Block coding, coding tool, and tool into line with the number of knives in the Block. ATC knife when the rotation, so that each knife seats followed through knowledge knife, knife found blocks, knives stopped the rotation. At this time there is no knife handle encoding part of the knife handle simplified.3. Annex coding methods. This style of coding keys, coded cards, coding and coding-disc, which is the most widely used coding keys.First to knives are attached to a tool of the show wrapped coding keys, and when the cutter knife to the store at knife in, so put the number of keys to remember knife Block Road, will be inserted into key to the coding Block next to the key hole in the seat for the knife to the numbers.ConclusionFocused on in today's manufacturing environment tool storage and management of new models and methods, practical application of good results in systems integration and optimization, and other aspects of operations will be further explored, so that it has a higher theoretical and practical level.译文：机床刀具设计课题研究意义机床原来的刀库控制程序是单独设计的，没有采用刀具管理系统，功能也比较单一，只实现了刀库刀具的找刀、刀库最短路径定位、主轴换刀，而且不支持大型刀具。
机械类 汉英词典
《汉英词典》机械类常用词汇(1)一画一字螺丝批 slot type screwdriver一点透视 one-point perspective二画二合一黏合剂 epoxy resin adhesive二合胶；混合胶 epoxy glue二维的；平面的 two-dimensional二进制 binary二极管；整流子 diode二号螺丝攻 second tap二路开关 two-way switch十进制的；公制的 metric人工制品 artefact人造板 man-made board人体工程学 ergonomics; human engineering 人体尺寸 human dimension人体测量学 anthropometry; anthropometrics 刀片 blade刀身 blade刀具 tool刀具溜座 carriage刀柱 tool post刀架 tool rest刀架底座 tool rest bracket刀座帷；床鞍 apron刀座鞍；溜板座 saddle力 force力三角形 triangle of force力平行四边形 parallelogram of force力多边形；多边形力学 polygon of force力的分解 force resolution力架；亮漆 lacquer力矩 moment力偶 couple力矩定律 law of moment力-距离图表 force-distance graph力图 force diagram力线 line of force力点 effort十字榫 cross halving joint十字螺丝 Philip's head screw十字螺丝批 Philip's type screwdriver丁字尺；T 尺 tee square三画三爪夹头 three-jaw chuck三角形结构系杆 triangulation tie三角锉 triangular file三维的；立体的 three-dimensional三氯甲烷；哥罗芳 chloroform三聚氰 胺；蜜胺 melamine三点透视 three-point perspective上油漆 painting上釉 enamelling凡立水 varnish叉形顶尖 fork centre口罩 mask士力；虫漆 shellac士巴拿；扳手 spanner大芯夹板；宽条芯夹板 blockboard; solid corestock-laminated board 大量制造 mass production子口刨；槽口刨；边刨 rebate plane小型平槽刨 miniature router plane小型线料弯曲器 small wire bender小型弯折机 mini bender小型电路断路器；跳菲 miniature circuit breaker (MCB)小齿轮 pinion山樟 San Cheong工件 workpiece工字梁 I beam工作面 working surface工作图；制作图 working drawing工作台 bench; working table工具 tool工具贮存室 tool storage工具槽 well工具钢 tool steel工场 workshop工场安全 workshop safety工程字书写技巧 lettering工程系统 engineering system工程绘图 engineering drawing工业酒精；火酒 methylated spirit弓形手钻；手摇曲柄钻 brace弓形手钻嘴 brace bit弓锯 bow saw; hacksaw弓锯片 hacksaw blade弓锯床 hacksawing machine《汉英词典》机械类常用词汇(2)四画不平衡 imbalance不含铁金属；非铁金属 non-ferrous metal不贯穿孔；闭孔；盲孔 blind hole不贯穿鸠尾榫 lapped dovetail joint不锈钢 stainless steel不稳定平衡 unstable equilibrium中心 centre中心线 centre line中心冲 centre punch中心钻 centre drill中心钻嘴 centre bit中央处理器 central processing unit (CPU)中性 neutral中性平衡；随遇平衡 neutral equilibrium中性轴 neutral axis中密度纤维板 medium density fibre board (MDF)中粗锉纹 second cut中碳钢 medium carbon steel中线 neutral wire互补金属氧化物半导体 complementary metal oxide semiconductors (CMOS) 介子；垫片 washer介指铁 ring mandrel介电常数；电容率 permittivity介稳态的；亚稳态的 metastable内力 internal force内卡尺 inside calipers内能 internal energy内涵性质 intensive properties内圆弯凿 scribing gouge内锁式配件 interlocking fitting内燃机 internal combustion engine内螺纹制造法 tapping内螺丝 internal thread内弯边 concave edge六角金属枝 hexagonal bar六角匙 Allen key六角头螺丝 hexagonal head screw公制的；十进制的 metric公差 tolerance冗余构件 redundant member分力 component force分子 molecule分子力 molecular force分切；分割；切断 parting off分贝 decibel分析 analysis分析及批判学 analytical and critical studies分析器 analyzer分流器 shunt分界面；界面；接口 interface分厘卡 micrometer分规 divider分割车刀架 parting tool holder分解 decomposition分压器 potential divider; voltage divider 隔离开关 isolating switch切削工具 cutting tool切削液 cutting fluid切削深度 depth of cut切屑；碎屑 chip切线锯法 tangential sawing切辊纹；滚纹 knurling切断；分切；分割 parting off切断工具 parting tool勾；勾脚 hook勾刀；胶片 刀 plastic cutter化胶水 tensol反向偏压 reverse biased反相放大器 inverting amplifier反相器 inverter反射 reflection反电动势 back e.m.f.反馈；回输 feedback天拿水；稀释剂 thinner天梯牙；齿条 gear rack天然木材 natural timber天然干燥法 air seasoning孔隙率 porosity尺寸 dimension尺寸线 dimension line尺身 blade引力；重力 gravitational force心形凸轮 heart-shaped cam心材 heartwood心轴 mandrel《汉英词典》机械类常用词汇(3)心销 core pin手工具 hand tool手工锯 junior hacksaw手削法 paring手持虎钳 hand vice手柄 handle手套 gloves手扫漆 brushing lacquer手推车 barrow手提式竖线锯 portable jigsaw手提电动工具 portable power tool手提电钻 electric hand drill手进给 hand feed手摇曲柄钻；弓形手钻 brace手摇钻 hand drill手锉 hand file手锯；板锯 handsaw手锥 bradawl手辘轧机 hand rolling machine支柱；支撑物 strut支架；支座 support支点 fulcrum; pivot文字 text方向 direction方向针 pointing needle方枝 square bar方波形 square waveform方波产生器 squarer方型牙板 rectangular die方格纸；网格纸 grid paper方通 square tube方块图 block diagram方锉 square file方头钻嘴 square shank bit方螺帽 square nut方边凿；直边凿 firmer chisel木 wood木工 woodwork木工工作间 woodwork area木工工作台 woodworker's bench木工车床 wood turning lathe; woodworking lathe木工铅笔 carpenter's pencil木工刨床 thicknessing and planning machine木牙螺丝；木螺钉 wood screw木材 timber木材车削 wood turning木材车削工具 wood turning tools木屑压合板；万花板 chipboard木条接榫 corner strip joint木圆头槌 doming mallet木模；模型 patterns木线 wood strip木胶粉 ureaformal dehyde resin glue木锉 rasp木螺钉；木牙螺丝 wood screw木槌 mallet止推轴承 thrust bearing止推垫圈 thrust washer比例 proportion比例尺 scale比例常数 proportionality constant比例极限 proportional limit比较器 comparator比热容量 specific heat capacity水平投影面 horizontal plane水平仪；平水尺 spirit level水气掣；漏电断路掣 earth leakage circuit breaker (ELCB)水晶胶；聚酯树脂 polyester resin水晶胶的铸造成形 resin casting水磨砂纸 silicon carbide paper火叉 firing fork火水；煤油 kerosene火牛；变压器 transformer火石轮 grinder火花电蚀法；放电极加工 electrical discharge machining 火酒；工业酒精 methylated spirit火钳 tongs火线；活线 live wire火砖 fire brick爪扣；爪形离合器；犬齿式离合器 dog clutch牙板；丝模 die牙板扳手；丝模扳手 die holder (stock)牙板螺帽 die nuts牛皮胶；动物胶 animal glue牛油纸 tracing paper牛顿运动定律 Newton's laws of motion犬齿式离合器；爪扣；爪形离合器 dog clutch《汉英词典》机械类常用词汇(4)五画丙烯 丁二烯苯乙烯 acrylonitrile-butadiene-stryrene (ABS) 主轴；心轴 spindle主题 motif令(纸张的计数单位) ream凹座 recess凹模 hollowing block凸缘 flange凸缘联轴节 flange coupling凸轮 cam凸轮式配件 cam-action fitting凸轮传动 cam drive凸头螺丝 raised head screw加成作业；添加法 addition process加油 oiling加速器 accelerator功能；用途 function功率因子 power factor功率放大器 power amplifier功率板 power amplifier board功率晶体管 power transistor包氏记号法 Bow's notation「包浩思」；「包豪斯」〈设计风格) Bauhaus半永固法；半永久接合 semi-permanent joining半接榫 halving joint半闭式槽榫 stopped housing joint半圆(木)锉 half-round rasp半圆车刀 turning gouge半圆锉 half-round file半圆头铆钉 snap rivet半导体 semiconductor卡路里；卡(热量单位) calorie卡纸 card paper卡尺；测径器 calipers去角；倒角 chamfer可切削性 machinability可行性 feasibility可逆过程 reversible process可压缩性 compressibility可变电阻 variable resistor四分仪 quadrant四爪夹头 four-jaw independent chuck四圆心法(绘图) four-centre method外卡尺 outside calipers外形塑造 shaping外形线；轮廓线 outline外推法 extrapolation外圆弯凿 firmer gouge外螺纹 external thread外螺纹制造法 threading外弯边 convex edge外观 appearance失真 distortion尼龙；聚醯胺 nylon; polyamide (PA)尼龙墨水针笔 technical felt-tip pen左右调校杆 lateral adjusting level市售尺寸；标准尺寸 stock size市电频率；电源频率 mains frequency平(木)锉 flat rasp平水尺；水平仪 spirit level平行投影 parallel projection平行车削 parallel turning平行虎钳 parallel vice平行钉法 parallel nailing平底弯刨 flat faced spokeshave平底钻嘴 forstner bit平板结构 slab construction平流扼流圈；滤波扼流器 smoothing choke平流电容器；滤波电容器 smoothing capacitor 平流电路；滤汳电路 smoothing circuit平面板；正台 surface plate平面图；俯视图 plan平面锤 flatter平移 translation平搭榫 corner halving joint平嘴钳 flat nose pliers平槽刨 router plane平衡 balance; equilibrium平衡力 equilibrant平衡条件 equilibrium condition平衡电桥 balanced bridge平头弧刀 square nose gouge幼纹 smooth cut打凹成形 hollowing打凸成形 raising打槽机 routing machine打线；打槽 routing打磨 fitting; polishing打磨机 polisher《汉英词典》机械类常用词汇(5)本生灯 Bunsen burner本征半导体 intrinsic semiconductor正反器；触发器；复振器 flip-flop正反馈；正回输 positive feedback正火 normalizing正向偏置 forward bias正投影 orthographic projection正投影图 orthographic drawing正弦波形 sinusoidal waveform正面投影 front projection正视图 elevation; front elevation正极；阳极 anode正齿轮 spur gear正台；平面板 surface plate永久性接合 permanent joining瓦通纸；瓦楞纸板 corrugated board生长层 cambium layer生产图 production drawing生胶浆 rubber cement生钢；铸钢 cast steel生铁；铸铁 cast iron用途；功能 function白杨木 poplar白胶浆 PVA glue; white glue皮沙垫 leather sandbag皮革 leather皮革黏合剂 leather glue皮鞋 leather shoes目录 contents矢量；向量 vector石灰岩 limestone石英晶体振荡器 quartz crystal oscillator 石棉 asbestos; asbestus石膏 Plaster of Paris示波器 oscilloscope立体图 pictorial drawing六画交流电流 alternating current (a.c.)交流电压 a.c. voltage交联结构 cross-linked structure仿饰金 gilding metal伏特 volt光力架 clear lacquer光拉软钢 bright drawn mild steel (B.D.M.S.)光敏电阻 light dependent resistor (LDR)光测弹性学 photoelasticity光刨；滑刨 smoothing plane光电效应 photoelectric effect光泽 lustre全闭式槽榫 closed housing joint共面力 coplanar force共聚合作用 co-polymerization共聚物 copolymer共价键 covalent bond共振；共鸣；谐振 resonance印刷电路板 printed circuit board (PCB)同素异形 allotropy同轴电缆 coaxial cable同温 equality of temperature向量；矢量 vector向量和 vector sum104合力 resultant force合口扁钳 close mouth tongs合成色；等和色 secondary colour合成品 composite合成粅料 composite material合金 alloy合金工具钢 alloy tool steel合钉；定位销 dowel回火 tempering回复力 restoring force回复力偶 restoring couple回弹 resilience回输；反馈 feedback地线 earth wire多刃切削刀具 multi-point cutter多孔塑料；泡沫塑料；海绵状塑料 foam plastics 多方榫接合 pinned joint多媒体 multi-media多晶性 polycrystallinity多谐振动器；多谐振荡器 multivibrator多边形力学；力多边形 polygon of force字母冲 letter punch字板 letter stencil安全 safety安全守则 safety rule安全系数 safety factor《汉英词典》机械类常用词汇(6)安全措施 safety precaution105安全眼罩 safety goggle安全设备 safety equipment安全药箱 safety box安培 ampere安培计；电流表 ammeter尖脚 spur年轮 annual ring成本 cost成形 forming扣件；击固件 fastener扣钉 clout nail; cramp托架 bracket收缩 shrinkage曲柄 crank曲柄轴 crank shaft曲线规；云板；云尺 French curve有效的 efficient有效电流 effective current灰；灰末 ash百折胶；百折胶；聚丙烯 polypropylene (PP) 竹 bamboo羊角锤 claw hammer老化 ageing肋条 rib肌理；质感；质地 texture自由度 degree of freedom自动控制 automatic control106自动进给 auto-feed自然干燥法 natural seasoning自感量 self-inductance自感应 self-induction色彩；颜色 colour色调 tone色环 colour wheel行星齿轮；周转齿轮 epicyclic gear七画肘节开关 toggle-switch串激电动机；串绕电动机 series-wound motor 位能；势能 potential energy位梯度；势梯度 potential gradient位移 displacement位错 dislocation伸长度 elongation作工硬化 work hardening作功 work done作图线 construction line低密聚乙烯 low density polyethylene (LDPE) 低通滤波器 low-pass filter低电压 low voltage低碳钢 low carbon steel布置 layout免油轴承 oil-less bearing冷加工；冷作工 cold working冷加工硬化 cold work hardening冷色 cool colour冷轧压 cold rolling冷却系统 cooling system冷却效应 cooling effect冷却液流量 coolant rate冷凝胶；环氧树脂 epoxy resin108利口；「披」口；铁屑 burr刨平 planing刨花板；碎料板 particle board吹风机 air blower吹气模塑；吹模塑 blow moulding吹管 blow pipe含铁金属 ferrous metal含水量 moisture content坑凿 cross-cut chisel均方根值 root mean square value均角投影图；等角投影图 isometric drawing 均速圆周运动 uniform circular motion夹；夹钳 clamp夹 cramp夹卡 mounting board夹具 fixture; jig夹具及固定装置 jig and fixture夹板；胶合板 plywood夹持工具 clamping device; holding tool夹背锯；榫锯 tenon saw夹头 chuck夹头开启匙；夹头扳手 chuck key夹叠黏合成形 lamination尾座 tailstock汉英词典》机械类常用词汇(7)床身；床道 lathe bed床鞍；刀座帷 apron形心；面心 centroid109形状 shape形变 deformation「快把」板；硬质纤维板 hardboard快速移位 rapid traverse抗扭强度 torsional strength抗屈强度 bending strength; yield strength抗性分量；无功分量 reactive component抗拉强度 tensile strength抗氧化剂 anti-oxidant抗剪强度 shearing strength抗磁性物料 diamagnetic material抗挠性 stiffness抗压强度 compressive strength抗断强度 breaking strength技术员；技师 technician扶架 steady扭力 torsion扭矩；转矩 torque扭转 torsion扭转角 angle of torsion把手 hand grip扼流圈 choke扳手 spanner; wrench投影 projection投影面 projection plane投影线 projection line攻丝 tap材料 material材料单；材料表 material list杜拉铝 duralumin杉木 spruce步进电动机 stepper motor步冲轮廓法 nibbling每分钟转数 revolution per minute (r.p.m.)系统组件 system component角托架 angle bracket角位移 angular displacement角板；直角板 angle plate角度 angle角榫 corner angle joint; corner joint角铁 angle iron谷巴凡立水 cobal varnish车刀架 tool holder车床 lathe车床工具 lathe tools车床中心钻咀 lathe centre bit车床操作法 lathe operation车削；车旋 lathe turning; turning车削工具 turning tools防火胶板 Formica防锈 rust prevention防声耳筒；护耳器 ear-protector防松螺帽 lock nut防护装置；保护罩；保护网 guard; safety guard汉英词典》机械类常用词汇(8)八画注射成形法；喷射铸造法 injection moulding并激电动机；并绕电动机 shunt-wound motor乳酪胶 casein glue乳胶漆 emulsion paint亚加力；压克力；聚甲基丙烯酸甲脂 acrylics; polymethyl methacrylate (PMMA) 亚稳态的；介稳态的 metastable来回摆动 oscillating两点透视 two-point perspective刻度；划线 ruling刺冲 dot punch刮刀 scraper刮擦 scraping制动鼓 drum brake制动碟 disc brake制动器 brake受迫振动 forced vibration受迫振荡 forced oscillation和谐 harmony周转齿轮；行星齿轮 epicyclic gear固定夹；台夹 bench holdfast固定负载 dead load定子 stator定位销；合钉 dowel定位螺丝 set screw定距轮 stitch marker屈片机 folding machine屈曲 bending屈服点；降服点 yield point屈圈法 loop forming屈卷法 scrolling屈接缝 folded lap seam屈喉机 tube bender屈折 folding屈折线 folding line屈压接缝 folded & grooved seam延性 ductility延性的 ductile弦锯法 plain sawing弧口凿；圆凿 gouge往复式运动 reciprocatory motion拉力 tensile force拉力计；张力计 tensiometer; tensometer拉钉 blind rivet; pop rivet拉钉接合 blind riveting; pop riveting拉钉钳 blind riveting pliers; pop riveting pliers拉张 tension拉张应力 tensile stress拉张应变 tensile strain拉细 drawing-down拉制法 drawing拉线 wire drawing「披」口；利口；铁屑 burr拔钳 nippers拋光 buffing拋光机 buffing machine放大；扩大 enlargement放大尺 pantograph放大倍数 amplification factor放大器 amplifier放电极加工；火花电蚀法 electrical discharge machining 易用万能尺 line setter易碎 fragile〈绘画的〉明暗运用；描影 shading枝；杆 rod杯形顶尖 cup centre杯头螺丝 hexagonal socket head cap screw板锯 panel saw松木 pine松节水 turpentine法式磨光 French polishing法拉〈电容量单位〉 farad油石；磨刀石 oil stone油漆；涂料 paint泡沫塑料；多孔塑料；海绵状塑料 foam plastics物理特性 physical property物理属性 physical attribute物理量 physical quantity盲孔；闭孔；不贯穿孔 blind hole直尺 ruler; straight rule直角叉榫 corner bridle joint直角尺 try square直角板；角板 angle plate直角杠杆 bell crank lever直身钻嘴 straight shank drill直车刀架 straight tool holder直流发电机 d.c. generator直流电流 direct current (d.c.)汉英词典》机械类常用词汇(9)直流电动机；直流马达 d.c. motor直纹锯 rip saw直线切削 linear interpolation直线运动 rectilinear motion直边凿；方边凿 firmer chisel直铁剪 straight snips硅 silicon空行程 idle stroke空气动力学 aerodynamics空间 space空载 no load花纹凿 embossing stamp花梨木 rosewood花样；图案 pattern虎克定律 Hooke's Law虎钳 vice虎钳护罩 vice clamp初步意念 proposed solution表面 surface表面展开图 surface development表面张力 surface tension表面处理 surface finishing; surface treatment表面硬化 case hardening表面硬化钢 case-hardened steel表达方式 presentation表达技巧；传意技巧 communication technique表观膨胀；视膨胀 apparent expansion金工 metalwork金工工作间 metalwork area金工角尺 engineering square金工车床 metalwork lathe金工虎钳 engineer's vice金工锯床 power hacksaw金属包头；金属箍 ferrule金属配件 metal fittings金属线 wire金属压展机 hand rolling mill金属擦光剂；磨光剂 metal polish金属薄片 sheet metal金属键 metallic bond长方通 rectangular tube长刨 trying plane长螺旋钻咀 long auger bit长镗孔 long boring闸极 gate阻抗 impedance附件 attachment附录 appendices青铜 bronze非反相放大器 non-inverting amplifier非本征半导体 extrinsic semiconductor非破坏性试验 non-destructive testing非晶状固体 amorphous solid非顽磁性铁磁材料 non-retentive ferromagnetic material 非压缩性流体 incompressible fluid非稳态 unsteady state非铁金属；不含铁金属 non-ferrous metal九画亮漆；力架 lacquer信号 signal信号产生机 signal generator信号处理 signal processing保养；维修 maintenance保险丝 fuse保护罩；保护网；防护装置 guard; safety guard 促凝剂 accelerator削屑 swarf垂直投影面 vertical plane型砧 swages〈书的〉封皮 binding封面 cover急回机构 quick return mechanism扁枝 bar扁头 cross-pein扁头法 upsetting扁头铆钉 flat head rivet扁头螺丝 flat head screw扁凿 flat chisel指示器 indicator指形榫 finger joint施力 effort染色 staining染色剂 stain架构 framework柄 stock柚木 teak柳安木 lauan流程图 flow chart汉英词典》机械类常用词汇(10)洗漆水 paint remover活塞 piston活塞销 gudgeon pin活线；火线 live wire炮铜 gun metal玻璃砂纸 glass paper玻璃胶 silicon sealant玻璃纤维 glass fibre玻璃纤维席 glass fibre mats界面；分界面；接口 interface相差 phase difference相对密度 relative density砂布 emery cloth砂磨 sanding砂磨纸 abrasive paper砂磨机 sander砂铸；砂铸模 sand casting研究探讨 research研磨；磨削 grinding研磨角 grinding angle科技 technology科技研习 technological studies科学知识 scientific knowledge科学瓷；聚氰胺毋醛树脂 melamine-formaldehyde resin (MF) 红铜垫圈 copper washer美学 aesthetics耐火胶板 fire-resisted laminate耐火砖 refractory block耐冲击聚苯乙烯 high impact polystyrene背 back胡桃木 walnut范德华引力 Van der Waals force英制惠氏标准螺纹 British Standard Whitworth thread (B.S.W.) 苯乙烯丙烯 共聚物 styrene-acrylonitrile copolymer苯酚甲醛 phenol formaldehyde (PF)计；规 gauge定时器 timer计划 planning计算器；计算机 computer计算器辅助工程 computer-aided engineering (CAE)计算器辅助控制 computer-aided control计算器辅助设计 computer-aided design (CAD)计算器辅助制造 computer-aided manufacturing (CAM)计算器数控 computer numerical control (CNC)负反馈；负回输 negative feedback负极；阴极 cathode负载 load轨路式砂纸磨机 orbital sander重力；引力 gravitational force重心 centre of gravity重量 weight重锉法 heavy filing限制开关；极限掣 limit switch限流器 current restrictor降服点；屈服点 yield point降压器 step down transformer面 plane面心；形心 centroid面材 plane materiel面板 face plate面板车削法 face plate turning面结型晶体管 junction transistor面罩 face mask音量 volume页边 margin风车锯；圆盘锯 circular saw风格 style风煤炉 forging hearth飞轮 flywheel飞机木；菠萨轻木 balsa首版；原型；雏形 prototype恒温器；温度调节器 thermostat十画俯视图；平面图 plan倒角；去角 chamfer倒模成形；模塑；铸模成形 moulding修边 trimming修边机 trimmer剖切面 cutting plane剖切面线 cutting plane line剖面；纵切面 section剖视图 sectional view剖线 hatching line刚性；刚度 rigidity刚性模量；刚性模数 modulus of rigidity刚强度；硬挺度 stiffness刚体 rigid body原子粒；晶体管 transistor汉英词典》机械类常用词汇(11原色 primary colour原型；雏形；首版 prototype原料 raw material哥罗芳；三氯甲烷 chloroform埋头直孔 counterbore埋头铆钉 countersink head rivet埋头锥孔 countersink埋头螺栓 countersink head bolt埋头螺丝 countersink head screw埋头钻 countersink drill埋头钻嘴 countersink bit; rose countersink drill 套筒；套管 sleeve套锤 fullers家用的 domestic展性 malleability展性的 malleable展开图 development峰至峰值 peak-to-peak value峰值 peak value差动放大器；微分放大器 differential amplifier 徒手草图 freehand sketch径线锯法 radial sawing径锯法 quarter sawing振动 vibration振幅 amplitude振荡 oscillating振荡运动 oscillatory motion振荡器 oscillator效率 efficiency时效硬化 age hardening时间常数 time constant框架 frame气动的系统；气压的系统 pneumatic system气动控制 pneumatic control气阀 gas valve气焊 gas welding空气压缩 air compression氧乙炔焊接 oxy-acetylene welding氧化 oxidation; oxidize消失点 vanishing point消色差 achromatic colour浸涂 dip coating海绵状塑料；泡沫塑料；多孔塑料 foam plastics 浮力 buoyancy浮雕 relief特性 property珠光体 pearlite疲劳 fatigue真空成形；真空吸塑 vacuum forming真空成形机 vacuum former真空吸塑成形法 vacuum moulding真实形状 true shape矩波形 rectangular waveform纹理 grain级联系统 cascade system纸板 carton board脆弱的；易碎的 brittle脆性 brittleness脉冲 pulse能量守恒 conservation of energy能量守恒定律 law of conservation of energy草图 sketch草图画纸 layout paper草稿 draft衰减 attenuation起化 magnetization起泡剂；发泡剂 foaming agent起动扭矩 starting torque起动器 starter起磁；磁化 magnetization退化 degradation退火 annealing配件 fitting钉合 nailing钉钳；铁钳 pincers钉冲 nail punch钉锤 cross-pein hammer针尖 point针叶 needle-point leaf针叶树 coniferous tree针锉；杂锦锉 needle files马氏体 martensite马达；电动机；摩打 motor马粪纸 straw board骨架结构 carcase construction容差；宽裕度 allowance高密度聚乙烯 high density polyethylene (HDPE)高通滤波器 high-pass filter汉英词典》机械类常用词汇(12高速钢 high speed steel高电压 high voltage高碳钢 high carbon steel十一画干燥法；干材法 seasoning偶合；耦合(电工) coupling侧面投影 side projection侧条芯夹板 laminboard侧视图；端视图 end elevation; end view偏心凸轮 eccentric cam偏向 bias; deviation偏差 deviation偏压 bias偏离 drift剪刀 scissors剪力 shearing force剪切 shear剪床；闸床 guillotine对角剪钳 diagonal cutting pliers动力工具 power tool动力学 dynamics动物胶；牛皮胶 animal glue动圈式电流计 moving coil galvanometer动态；运动 movement动态平衡 dynamic equilibrium动摩擦 dynamic friction; kinetic friction匙孔锯 key-hole saw; pad saw只读存贮器；只读存储器 read only memory (ROM)国际标准组织 The International Standard Organization (ISO) 基本设计原理 design fundamentals基极电流 base current基准边 true edge基尔霍夫定律；克希何夫定律 Kirchhoff's Law密度 density常规 conventions带式砂磨机 belt sander带式传动 belt drive带通滤波器 band-pass filter带锯；运锯 band-saw张力计；拉力计 tensiometer; tensometer 强化 reinforcement强化塑料 reinforced plastics彩度 chroma控制系统 control system卷尺 flexible rule; tape rule接口；界面；分界面 interface接合 joining接合工具 joining tool接地 earthing接缝 lapped seam; seam接触角 angle of contact扫上光油 varnishing推拔车削 taper turning推进器 propeller斜切车刀 skew turning chisel斜投影 oblique projection斜角 mitre斜角；斜面 bevel斜角规 bevel; sliding bevel斜角榫 mitre joint斜身螺丝攻 taper tap斜格纸；等角投影纸 isometric grid paper 〈织物的〉斜纹 bias斜钉法 dovetail nailing斜率 gradient斜视图 oblique drawing斜榫尺 mitre square斜榫规 mitre gauge斜槽位；鱼尾槽位 dovetail trench斜边凿 bevel edged chisel旋扭法 twisting旋钮；球形把手 knob旋制法 spinning旋转；转动 rotation旋转台 rotating platform旋转轴 rotating shaft旋转运动 rotary motion杆；枝 rod条线图；棒形图 bar chart梨形凸轮 pear-shaped cam液相 liquid phase液晶体显示 liquid crystal display (LCD)液压 liquid compression液压控制 hydraulic control液压机 hydraulic press添加法；加成作业 addition process汉英词典》机械类常用词汇(13添加剂 additive清漆 varnish清胶 gel resin混合胶；二合胶 epoxy glue深拉制法 deep drawing深度计；深度规 depth gauge淬火 quench淬火液 quenching liquid淬硬 quench hardening焊接 welding焊枪 brazing torch焊剂 flux焊炉 brazing hearth球形把手；旋钮 knob球体 sphere瓷釉；搪瓷；珐琅 enamel瓷漆；磁漆 enamel paint产品设计规格 product design specification (PDS) 眼罩 goggles硫化作用 vulcanization移印字 dry rub on transfers第一角投影法 first angle projection第三角投影法 third angle projection符号 symbol粗削 roughing粗纹 bastard cut粗刨 jack plane统一〈设计〉 unity组件 component; module组合角尺 combination square组合钳 combination pliers组合图；装配图 assembly drawing汇编语言；汇编语言 assembly language组合逻辑 combinational logic组成物料 component material组织原理(设计) organisation脱碳 decarburization脱模剂 release agent脱模腊 mould release wax茎 stem蛋形木槌 bossing mallet规；计 gauge规身 stock规柄 stem规格 specification许可应力 permissible stress设计 design设计元素 design element设计作业；专题设计研习 design project设计师 designer设计记录档案 design folder设计组织 design organization设计处境；设计环境 design situation设计规格 design specification设计提案 design proposal设计程序 design process设计概要；设计纲要 design brief设计解决方法 design solution贯穿鸠尾榫 through dovetail joint软木 softwood软板；绝缘板 soft board软胶；聚乙烯 polyethylene (PE)软焊 soft soldering软焊料 soft solder软钢 mild steel通用面板 universal surface plate连接杆；连杆 linkage连结板 web连续插图 sequential drawing速度 velocity速度比 velocity ratio造形 form造型砂 moulding sand透明；通透 transparent透视投影 perspective projection透视法 perspective透视图 perspective drawing131闭孔；盲孔；不贯穿孔 blind hole闭合电路 closed circuit死循环控制 closed-loop control死循环控制系统 closed control system 死循环增益 close loop gain阴极；负极 cathode陶瓷 ceramics陶瓷制品 ceramic product顶尖 centre顶面投影 top projection汉英词典》机械类常用词汇(14顶脱销 ejector pin鱼尾半接榫 dovetailed tee halving joint 鱼尾榫；鸠尾榫；燕尾榫 dovetail joint 鱼尾槽位；斜槽位 dovetail trench麻花钻 twist drill梣木 ash焗炉 oven焓 enthalpy十二画家俬钉 panel nail家俬蜡 furniture wax伞齿轮 bevel gear最后方案 final solution割线规 cutting gauge喇叭；扬声器 speaker单元 module单板；薄木皮 veneer单板镶贴；薄皮镶合 veneering单相 single phase单脚规 odd-leg calipers单路开关 one-way switch单鸠尾榫 single dovetail joint单碟离合器 single plate clutch单稳态 monostable喉管 tube围裙 apron循环车削 turning cycle循环过程 cyclic process惠斯登电桥 Wheatstone bridge惰轮 idler描影；(绘画的)明暗运用 shading插座 socket插头 plug换能器；转能器；传感器 transducer扬声器；喇叭 loud speaker; speaker晶粒 grain晶体 crystal晶体振荡器 crystal oscillator晶体结构 crystal structure晶体管；原子粒 transistor晶体点阵；晶体格构；晶格 crystal lattice棘轮和爪 ratchet and pawl棘齿 ratchet棘齿弓钻 ratchet brace壳型模塑 shell moulding光标卡尺 vernier calipers减除作业 reduction process涡流 eddy current涡轮机 turbine测径器 calipers测试工具 testing tool焦炭 coke无功分量；抗性分量 reactive component无彩色 achromatic colour无头螺丝 grub screw无压释放器 no-voltage release无稳态定时器 astable timer无稳态电路 astable circuit无稳态多谐振动器；无稳态多谐振荡器；无稳态复振器 astable multivibrator 然纳二极管；齐纳二极管 Zener diode珐琅；搪瓷；瓷釉 enamel画板；绘图板 drawing board画纸 drawing paper发光二极管 light emitting diode (LED)发泡聚苯乙烯；发泡胶 expanded polystyrene (EPS); styrofoam 发泡剂；起泡剂 foaming agent发电机 generator发热管 heating tube发热线切割机 hot wire cutter发热线机 hot wire machine; strip heater短路 short circuit硬化 hardening硬化剂 curing agent; hardener; hardening agent硬木 hardwood硬件〈计算机〉 hardware硬度 hardness硬度测试 hardness test硬挺度；刚强度 stiffness硬焊 hard soldering硬模铸造；压力铸造；压铸 die casting硬胶；聚苯乙桸 polystyrene (PS)硬质纤维板；「快把」板 hardboard程序；程序 program稀释剂；天拿水 thinner汉英词典》机械类常用词汇(15)等角投影 isometric projection等角投影纸；斜格纸 isometric grid paper等角投影图；均角投影图 isometric drawing等角轴 isometric axis等角圆 isometric circle等和色；合成色 secondary colour等焓的过程 isentropic process筒夹；弹性夹头 collet筒形线圈；螺线管；电磁线圈 solenoid结构 structure结构力学 structural mechanics结构木材 structural timber绝缘 insulation绝缘板 insulation board绝缘体 insulator丝攻扳手 tap wrench丝模；牙板 die丝模扳手；牙板扳手 die holder (stock)菠萨轻木；飞机木 balsa虚线；隐线 hidden line视查 visual inspection视膨胀；表观膨胀 apparent expansion评估 evaluation评鉴 criticism象限 quadrant超塑料 superplastic超载 overload超声波 ultrasonic wave超声波测试 ultrasonic test轴 shaft轴心车削法 turning between centres轴功 shaft work轴承 bearing轴接 coupling轴环；卡圈 collar周期 period进料螺杆 feed screw进给 feed进给速率 feed rate进给螺杆 feed screw量角器 protractor量度 measurement量度工具 measuring tool钝 blunt开口式槽榫 through housing joint开口扁钳 open mouth tongs开口销 cotter pin开孔凿 hole punch开材方法(木材) conversion开环控制系统 open-loop control system阳极；正极 anode阳极氧化法；阳极处理 anodizing集成电路 integrated circuit (IC)集电极电流 collector current云尺；云板；曲线规 French curve云母 mica韧皮部 bast韧性 toughness顺磁性 paramagnetic material黄金分割 golden section黄金比例 golden ratio黄铜 brass黑皮软钢 black mild steel十三画传动系统 drive system传动螺杆 drive screw传意技巧；表达技巧 communication technique 传感器；换能器；转能器 transducer传热性 conductivity of heat传导 conduction传导性 conductivity倾角 angle of inclination; rake angle倾斜面 inclined plane势能；位能 potential energy势梯度；位梯度 potential gradient汇编语言；汇编语言 assembly language圆口夹钳 round tongs圆形及椭圆形尺 circle and ellipse guide圆形凸轮 circular cam圆形开口牙板 circular split die圆咀钳 round nose pliers。
机床——机械类外文文献翻译、中英文翻译
毕业设计(论文)外文资料翻译系部：专业：姓名：学号：外文出处：English For Electromechanical(用外文写)Engineering附件：1.外文资料翻译译文；2.外文原文。
附件1：外文资料翻译译文机床机床是用于切削金属的机器。
工业上使用的机床要数车床、钻床和铣床最为重要。
其它类型的金属切削机床在金属切削加工方面不及这三种机床应用广泛。
车床通常被称为所有类型机床的始祖。
为了进行车削，当工件旋转经过刀具时，车床用一把单刃刀具切除金属。
用车削可以加工各种圆柱型的工件，如：轴、齿轮坯、皮带轮和丝杠轴。
镗削加工可以用来扩大和精加工定位精度很高的孔。
钻削是由旋转的钻头完成的。
大多数金属的钻削由麻花钻来完成。
用来进行钻削加工的机床称为钻床。
铰孔和攻螺纹也归类为钻削过程。
铰孔是从已经钻好的孔上再切除少量的金属。
攻螺纹是在内孔上加工出螺纹，以使螺钉或螺栓旋进孔内。
铣削由旋转的、多切削刃的铣刀来完成。
铣刀有多种类型和尺寸。
有些铣刀只有两个切削刃，而有些则有多达三十或更多的切削刃。
铣刀根据使用的刀具不同能加工平面、斜面、沟槽、齿轮轮齿和其它外形轮廓。
牛头刨床和龙门刨床用单刃刀具来加工平面。
用牛头刨床进行加工时，刀具在机床上往复运动，而工件朝向刀具自动进给。
在用龙门刨床进行加工时，工件安装在工作台上，工作台往复经过刀具而切除金属。
工作台每完成一个行程刀具自动向工件进给一个小的进给量。
磨削利用磨粒来完成切削工作。
根据加工要求，磨削可分为精密磨削和非精密磨削。
精密磨削用于公差小和非常光洁的表面，非精密磨削用于在精度要求不高的地方切除多余的金属。
车床车床是用来从圆形工件表面切除金属的机床，工件安装在车床的两个顶尖之间，并绕顶尖轴线旋转。
车削工件时，车刀沿着工件的旋转轴线平行移动或与工件的旋转轴线成一斜角移动，将工件表面的金属切除。
车刀的这种位移称为进给。
车刀装夹在刀架上，刀架则固定在溜板上。
溜板是使刀具沿所需方向进行进给的机构。
机械专业常用词汇翻译
机械专业常用词汇翻译1. Introduction机械专业是一个重要的工程领域，涉及各种机械设备、制造工艺和相关技术。
在机械专业学习和工作中，熟悉并理解常用的机械专业词汇翻译是非常重要的。
本文档旨在为机械专业学习者提供一个常用词汇的翻译参考，帮助他们更好地理解和运用机械专业的知识。
2. 机械部件和设备以下是机械专业中常用的部件和设备的词汇翻译：•机床：Machine tool•机械臂：Robotic arm•传送带：Conveyor belt•齿轮：Gear•轴承：Bearing•轴：Shaft•螺丝：Screw•螺母：Nut•锁紧螺母：Locknut•螺栓：Bolt•螺母：Nut•螺旋弹簧：Coil spring•缸体：Cylinder block•活塞：Piston•液压系统：Hydraulic system •气压系统：Pneumatic system •水冷系统：Water cooling system •电机：Motor•发动机：Engine•减速器：Reducer•离合器：Clutch•制动器：Brake•摩擦片：Friction disk•活门：Valve•曲柄连杆机构：Crankshaft mechanism•曲线轴承：Cam bearing•铣床：Milling machine•钻床：Drilling machine•磨床：Grinding machine•压力机：Press machine•液压机：Hydraulic press•塑料注塑机：Plastic injection molding machine •金属切割机：Metal cutting machine•金属冲压机：Metal stamping machine 3. 制造工艺以下是机械专业中常用的制造工艺的词汇翻译：•制造工艺：Manufacturing process•机械加工：Machining•铣削：Milling•铣床加工：Milling machine process•钻削：Drilling•钻床加工：Drilling machine process•磨削：Grinding•磨床加工：Grinding machine process•冲压：Stamping•冲压机加工：Stamping machine process•注塑：Injection molding•注塑机加工：Injection molding machine process •焊接：Welding•焊接工艺：Welding process•铆接：Riveting•铆接工艺：Riveting process•激光切割：Laser cutting•激光切割工艺：Laser cutting process•激光焊接：Laser welding•激光焊接工艺：Laser welding process•表面处理：Surface treatment•镀膜：Plating•镀膜工艺：Plating process•喷涂：Spraying•喷涂工艺：Spraying process4. 测量和控制以下是机械专业中常用的测量和控制相关的词汇翻译：•测量：Measurement•控制：Control•传感器：Sensor•仪表：Instrument•数字显示器：Digital display•仪表盘：Dashboard•电气控制系统：Electrical control system•自动控制系统：Automatic control system•PLC：Programmable logic controller•CNC：Computer numerical control•示波器：Oscilloscope•流量计：Flow meter•压力计：Pressure gauge•温度计：Thermometer•液位计：Level gauge•压力传感器：Pressure sensor•温度传感器：Temperature sensor •位置传感器：Position sensor•加速度计：Accelerometer•加速度传感器：Accelerometer sensor •控制阀：Control valve•电动阀门：Electric valve•运动控制：Motion control•频率控制：Frequency control5. 结论本文档提供了机械专业常用词汇的翻译参考，方便机械专业学习者更好地理解和运用机械专业知识。
机械加工中术语中英文对照
机械加工术语中英文对照机械加工专业术语中英文对照拋光polishing安装to assemble扳手wrench半机械化semi-mechanization; semi-mechanized 半自动滚刀磨床semi—automatic hob grinder半自动化semi—automation；semi—automatic备件spare parts边刨床side planer变速箱transmission gear柄轴arbor部件units; assembly parts插床slotting machine拆卸to disassemble超高速内圆磨床ultra-high—speed internal grinder 车床lathe; turning lathe车刀lathe tool车轮车床car wheel lathe车削turning车轴axle衬套bushing 按英文字母排序3—Jaws indexing spacers 三爪、分割工具头A。
T。
C.system 加工中心机刀库Aluminum continuous melting & holding furnaces 连续溶解保温炉Balancing equipment 平衡设备Bayonet 卡口Bearing fittings 轴承配件Bearing processing equipment 轴承加工机Bearings 轴承Belt drive 带传动Bending machines 弯曲机Blades 刀片Blades，saw 锯片Bolts,screws ＆nuts 螺栓，螺帽及螺丝Boring heads 搪孔头Boring machines 镗床Cable making tools 造线机Casting,aluminium 铸铝Casting，copper 铸铜Casting，gray iron 铸灰口铁Casting，malleable iron 可锻铸铁Casting，other 其他铸造Casting,steel 铸钢Chain drive 链传动Chain making tools 造链机Chamfer machines 倒角机Chucks 夹盘Clamping/holding systems 夹具/支持系统CNC bending presses 电脑数控弯折机CNC boring machines 电脑数控镗床CNC drilling machines 电脑数控钻床CNC EDM wire-cutting machines 电脑数控电火花线切削机CNC electric discharge machines 电脑数控电火花机CNC engraving machines 电脑数控雕刻机CNC grinding machines 电脑数控磨床CNC lathes 电脑数控车床CNC machine tool fittings 电脑数控机床配件CNC milling machines 电脑数控铣床CNC shearing machines 电脑数控剪切机CNC toolings CNC刀杆CNC wire-cutting machines 电脑数控线切削机Conveying chains 输送链Coolers 冷却机Coupling 联轴器Crimping tools 卷边工具Cutters 刀具Cutting—off machines 切断机Diamond cutters 钻石刀具Dicing saws 晶圆切割机Die casting dies 压铸冲模Die casting machines 压铸机Dies-progressive 连续冲模Disposable toolholder bits 舍弃式刀头Drawing machines 拔丝机Drilling machines 钻床Drilling machines bench 钻床工作台Drilling machines，high—speed 高速钻床Drilling machines，multi-spindle 多轴钻床Drilling machines,radial 摇臂钻床Drilling machines，vertical 立式钻床drills 钻头Electric discharge machines(EDM) 电火花机Electric power tools 电动刀具Engraving machines 雕刻机Engraving machines，laser 激光雕刻机Etching machines 蚀刻机Finishing machines 修整机Fixture 夹具Forging dies 锻模Forging，aluminium 锻铝Forging，cold 冷锻Forging,copper 铜锻Forging，other 其他锻造Forging，steel 钢锻Foundry equipment 铸造设备Gear cutting machines 齿轮切削机Gears 齿轮Gravity casting machines 重力铸造机Grinder bench 磨床工作台Grinders，thread 螺纹磨床Grinders,tools & cutters 工具磨床Grinders，ultrasonic 超声波打磨机Grinding machines 磨床Grinding machines，centerless 无心磨床Grinding machines，cylindrical 外圆磨床Grinding machines,universal 万能磨床Grinding tools 磨削工具Grinding wheels 磨轮Hand tools 手工具Hard/soft and free expansion sheet making plant 硬(软)板(片)材及自由发泡板机组Heat preserving furnaces 保温炉Heating treatment funaces 熔热处理炉Honing machines 搪磨机Hydraulic components 液压元件Hydraulic power tools 液压工具Hydraulic power units 液压动力元件Hydraulic rotary cylinders 液压回转缸Jigs 钻模Lapping machines 精研机Lapping machines，centerless 无心精研机Laser cutting 激光切割Laser cutting for SMT stensil 激光钢板切割机Lathe bench 车床工作台Lathes，automatic 自动车床Lathes，heavy-duty 重型车床Lathes,high-speed 高速车床Lathes，turret 六角车床Lathes,vertical 立式车床Lubricants 润滑液Lubrication Systems 润滑系统Lubricators 注油机Machining centers,general 通用加工中心Machining centers,horizontal 卧式加工中心Machining centers,horizontal & vertical 卧式及立式加工中心Machining centers，vertical 立式加工中心Machining centers,vertical double—column type 立式双柱加工中心Magnetic tools 磁性工具Manifolds 集合管Milling heads 铣头Milling machines 铣床Milling machines,bed type 床身式铣床Milling machines,duplicating 仿形铣床Milling machines,horizontal 卧式铣床Milling machines,turret vertical 六角立式铣床Milling machines,universal 万能铣床Milling machines,vertical 立式铣床Milling machines,vertical ＆horizontal 立式及卧式铣床Mold ＆die components 模具单元Mold changing systems 换模系统Mold core 模芯Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹Mold repair 模具维修Molds 模具Nail making machines 造钉机Oil coolers 油冷却器Overflow cutting machines for aluminium wheels 铝轮冒口切断机P type PVC waterproof rolled sheet making plant P型PVC高分子防水PCB fine piecing systems 印刷电器板油压冲孔脱料系统Pipe & tube making machines 管筒制造机Planing machines 刨床Planing machines vertical 立式刨床Pneumatic hydraulic clamps 气油压虎钳Pneumatic power tools 气动工具Powder metallurgic forming machines 粉末冶金成型机Presses，cold forging 冷锻冲压机presses，crank 曲柄压力机Presses,eccentric 离心压力机Presses,forging 锻压机Presses,hydraulic 液压冲床Presses，knuckle joint 肘杆式压力机Presses，pneumatic 气动冲床Presses，servo 伺服冲床Presses,transfer 自动压力机Pressing dies 压模Punch formers 冲子研磨器Quick die change systems 速换模系统Quick mold change systems 快速换模系统Reverberatory furnaces 反射炉Rollers 滚筒Rolling machines 辗压机Rotary tables 转台Sawing machines 锯床Sawing machines，band 带锯床Saws，band 带锯Saws，hack 弓锯Saws，horizontal band 卧式带锯Saws，vertical band 立式带锯shafts 轴Shapers 牛头刨床Shearing machines 剪切机Sheet metal forming machines 金属板成型机Sheet metal working machines 金属板加工机Slotting machines 插床spindles 主轴Stamping parts 冲压机Straightening machines 矫直机Switches & buttons 开关及按钮Tapping machines 攻螺丝机Transmitted chains 传动链Tube bending machines 弯管机Vertical hydraulic broaching machine 立式油压拉床Vises 虎钳Vises，tool—maker 精密平口钳Wheel dressers 砂轮修整器Woven—Cutting machines 织麦激光切割机Wrenches 扳手。
机械行业专业英语词汇刀具类
机械行业专业英语词汇刀具类金属切削metal cutting 机床machine tool 金属工艺学technology of metals 刀具cutter 摩擦friction 联结link 传动drive/transmission 轴shaft 弹性elasticity 频率特性frequency characteristic 误差error 响应response 定位allocation 机床夹具jig 动力学dynamic 运动学kinematic 静力学static 分析力学analyse mechanics 拉伸pulling 压缩hitting 剪切shear 扭转twist 弯曲应力bending stress 强度intensity 三相交流电three-phase AC 磁路magnetic circles 变压器transformer 异步电动机asynchronous motor 几何形状geometrical 精度precision 正弦形的sinusoid 交流电路AC circuit 机械加工余量machining allowance 变形力deforming force 变形deformation 应力stress 硬度rigidity 热处理heat treatment 退火anneal 正火normalizing 脱碳decarburization 渗碳carburization 电路circuit 半导体元件semiconductor element 反馈feedback 发生器generator 直流电源DC electrical source 门电路gate circuit 逻辑代数logic algebra 外圆磨削external grinding 内圆磨削internal grinding 平面磨削plane grinding 变速箱gearbox 离合器clutch 绞孔fraising 绞刀reamer 螺纹加工thread processing 螺钉screw 铣削mill 铣刀milling cutter 功率power 工件workpiece 齿轮加工gear mechining 齿轮gear 主运动main movement 主运动方向direction of main movement 进给方向direction of feed 进给运动feed movement 合成进给运动resultant movement of feed 合成切削运动resultant movement of cutting 合成切削运动方向direction of resultant movement of cutting 切削深度cutting depth 前刀面rake face 刀尖nose of tool 前角rake angle 机械专业词汇：hardenability 淬透性carbide tool 硬质合金刀具alloy tool steel 合金工具钢alloyed cast iron 合金铸铁carbon steel 碳素钢carbon tool steel 碳素工具钢cast iron 铸铁caststeel 铸钢die material 模具材料high alloy steel 高合金钢high carbon steel 高碳钢low alloy steel 低合金钢low carbon steel 低碳钢shock resistant tool steel 抗冲击工具钢nodular graphite iron 球墨铸铁malleable cast iron 可锻铸铁mottled cast iron 麻口铸铁hardenability curve 淬透性曲线hardening capacity 淬硬性(硬化能力) hardness penetration diagram “U”形曲线hardness profile 硬度分布(硬度梯度) heat treatment procedure热处理规范heat treatment installation 热处理设备heat treatment furnace 热处理炉heat treatment cycle 热处理工艺周期heat time 加热时间heat system 加热系统heating up time 升温时间heating curve 加热曲线high temperature carburizing 高温渗碳high temperature tempering 高温回火isothermal annealing 等温退火interrupted ageing treatment 分级时效处理local heat treatment 局部热处理overheated structure 过热组织pack carburizing 固体渗碳Oxynitrocarburizing 氧氮碳共渗partial annealing 不完全退火recrystallization temperature 再结晶温度cutting part 切削部分tool angle 刀具角度tool back angle 背前角tool back clearance 背后角tool backlash movement (tool retracting) 退刀tool back wedge angle 背楔角tool base clearance 基后角tool cutting edge plane 切削平面tool cutting edge angle 主偏角tool grinding machine 工具磨床tool geometrical rake 几何前角tool nomal clearance(rake) 法后角(法前角) tool orthogonal clearance(rake, wedge) 后角(前角，楔角) locating device 定位装置locating face 定位面locating pin定位销(挡料销) locating plate 定位板locating ring 定位圈locating rule 定位尺locating element 定位零件(定位要素) work hardening 加工硬化internal cylindrical grinding machine 内圆磨床internal cylindrical turing 内圆车削internal force 内力internal cylindrical grinding machine with vertica 立式内圆磨床hole scraping (turning,milling, lapping) 刮孔(车孔，铣孔，研孔) holegrinding (slotting,honing, flanging) 磨孔(插孔，珩孔，翻孔) versatile grinding machine 多用磨床versatile lathe 多用车床vertical multi-tool lathe 立式多刀车床precision milling machine 精密铣床spot face 孔口平面drill and countersink 定心钻，中心钻counterbore cutter head 扩孔钻头jig boring machine 坐标镗床jig grinding machine 坐标磨床jig and fixture夹具fixture of gear cutting machine 齿轮加工机床夹具fixture of milling machine 铣床夹具fixture of grinding machine 磨床夹具fixture of planing machine 刨床夹具fixture of slotting machine 插床夹具vacuum fixture 真空夹具universal fixture (jig) 通用夹具stationary fixture 固定夹具standard fixture (jig) 标准夹具pneumatic fixture (jig) 气动夹具open-side boring and milling machine 悬臂镗铣床magnetic fixture (jig) 磁力夹具locating device (face,element) 定位装置(面，元素) hydraulic fixture (jig) 液压夹具slide gauge 游标卡尺triple action press 三动压力机tow point single action press 双点单动压力机watch press 台式压力机closed type single action crank press 闭式单动(曲柄)压力机one point single action press 单点单动压力机open-back inclinable press 开式双柱可倾压力机four crank press 四曲柄压力机stright side single action double crank press 闭式双点单动双曲柄压力机singlepiece frame press 整体框架式压力机rocker arm type press 摇臂式压力机top drive sheet metal stamping automatic press 上传动板料冲压自动压力机barrel surface 圆柱形表面antiflowback valve 反流阀reciprocating-screw machine 往复螺旋注塑机single-stage plunger 单级柱塞shot chamber 注射室curing temperature 固化温度shot capacity 注射能力plunger diameter 柱塞直径sectional area of plunger 柱塞面积hydraulic cylinder 液压缸blanking die 冲裁模blanking clearance, die clearance 冲裁间隙blanking force 冲裁力die,stamping and punching die 冲模tonnage of press 压力机吨位shut height of press machine 压力机闭合高度clearance between punch and die 凹凸模间隙tolerance of fit 配合公差shearing force diagram 剪力图peak die load 模具最大负荷center of die, center of load 压力中心clamping force (element, device, piston) 夹紧力(件，装置，活塞) clamp plate (ring) 压板(夹紧环) shearing force (plane) 剪切力(平面) side clearance angle 侧隙角side locating face 侧定位面side-push plate 侧压板shuttle table 移动工作台matrix plate 凹模固定板material removal rate 材料切除率sheet matal 板料blanking die 冲裁模assembling die 复合冲模，装配用模具compound blank and pierce dies 落料冲孔模shaving die 切边模，修边模shankless die 无柄模具scrapless progressive die 无废料连续模return-blank type blanking die 顶出式落料模expanding die 胀形模，扩管模die for special purpose 专用模cavity plate (block) 凹模bend ability 可弯性bend arc 弯曲弧bending angle (line) 弯曲角(线) bending brake (bending machine) 弯板机，拆弯机bending fatigue 弯曲疲劳bending radius 弯曲半径minimumbending radius 最小弯曲半径bending operation 弯曲工序air-bend die 自由弯曲模bending moment diagram 弯矩图blank length of bend 弯曲件展开长度relative bending radius 相对弯曲半径bending equipment for plastics 塑料折弯设备drawing machine 拉拔机drawing numbers 拉伸次数drawing ratio (coefficient,force,speed) 拉伸比(系数，力，速度) foamed (cellular) plastic 泡沫塑料Thermoplastic 热塑性塑料plastic industry 塑料(工业)行业blow molding die for plastics 塑料吹模机standard die components for plastics 塑料模具标准化零部件thermoforming machine for plastics 塑料热成型机foaming mold for plastics 泡沫塑料模型plastic molding press 塑料制品成型压力机other plastics converting machine 其它塑料加工机械compression molding machine 压塑机extruder double-screw for plastics 塑料加工用双螺杆挤压机extruder single-screw for plastics 塑料加工用单螺杆挤压机laminating machine 层压机parting surface 分型面transfer mold 压注模(也称传递模) flash-type mold 溢出式压缩模portable transfer mold 移动式压注模mold for plastics 塑料成型模具(简称塑料模) mold for thermoplastics 热塑性塑料模Draft 脱模斜度transfer mold 传递模injection mold for thermoplastics 热塑性塑料注射模portable transfer mold 移动式传递模fixed transfer mold 固定式传递模insulated runner mold 绝热流道模warm runner mold 温流道模ring gate 环形浇口pin-point gate 点浇口edge gate 侧浇口submarine gate, tunnel gate 潜伏浇口runner plate 流道板spreader 分流锥warm runner plate 温流道板stationary mold, fixed half, fixed die, cover die 定模moving die, movable mold, moving half 动模sprue gating中心浇口，浇道浇口die-casting die 压力铸造模具(简称压铸模) fixed clamping plate 定模底板moving clamping plate 动模底板support plate, backing plate 支承板movable core 活动型芯baffle 导流块sprue spreader 分流锥(分流器) ejector pin (plate) 推杆(板) ejector pin retaining plate 推杆固定板gate 内浇口air vent 排气槽parting line 分型面feed (gating, runner) system 浇注系统pouring temperature (rate, time) 浇注温度(速度，时间) sprue base (bush, gate, puller) 直浇道窝(浇口套，直接浇口，拉料杆) final forging temperature 终锻温度finishing temperature 终锻温度initial forging temperature 始锻温度flat die hammer 自由锻锤forge furnace 锻炉forge ratio (forge reduction) 锻造比forging crankpress 锻造用曲柄压力机forging die (die steel, drawing) 锻模(锻模钢，锻件图) forging line (load, practice) 锻造生产线(负荷，工艺) forging plane (plant) 锻造面(厂) forging pressure (process, range) 锻造力(工艺，范围) hammer forging die 锤锻模forging heat-treatment 锻件热处理forging temperature interval 锻造温度范围forging tolerance 锻件公差hot forging drawing热锻件图chip formation 成型切削chip load (force) 切削力drilling and reaming 钻孔和铰孔taper turning 锥度车削external threading 外螺纹车削chuck handle 夹头扳手，夹头钥匙combination chuck 复动夹头shaper and planer 牛头刨床和龙门刨床slotting machine 插床rotary-type bushing 旋转衬(钻)套underlying metal 底层金属perforated electrode 多孔电极electro-chemical machining 电化学加工form electromachining 电加工成形面electric machining 电加工salt bath electrode furnace 电极盐浴炉electrolytic forming machine 电解成形机electrochemicalmachining 电解加工electrochemical machining tool 电解加工机床electrolytic universal tool and cutter grinder 电解万能工具磨床electrolytic heat treatment 电解液热处理electrohydraulic forming 电液成形electrolytic marking machine 电解刻印机electrolytic surface grinder 电解平面磨spark erosion machining 电火花加工法electrical discharge machining (EDM) 电火花加工electrodischarge cutting machine 电火花切割机electrical discharge machine 电火花加工机床electrical spark-erosion perforation 电火花打孔electrode contact surface 电极接触面electrical discharge forming 电火花成形机laser cutting machine 激光切割机electron beam cutting machine 电子束切割机cavity sinking EDM machines 型腔电火花加工机床travelling-wire EDM machine 线电极电火花加工机床electro-discharge machine tool 电火花加工机床electron beam machining (EBM) 电子束加工electron beam machine tool 电子束加工机床form electromachining 电加工成形面tiny holespark-erosion grinding machine 电火花小孔磨床spark-erosion cutting with a wire 电火花线切割wire cut electric discharge machine 电火花线切割机encoded transducer 编码传感器compensator 补偿器incremental measuring system 增量测量系统analog control 模拟控制assembly language 汇编语言dataprocessing system 数据处理系统graphic data processing 图形处理linear (circle) interpolator 线形(圆形)插补器DNC--direct numerical control 直接数字控制CNC--computer numerical control 计算机数字控制DPU--Data Processing Unit 数控处理单元DLU--Data Loops Unit 数据循环单元cutter saddle 刀架cylinder saddle 鞍形气缸座a safety loop 保险圈a wire loop 钢丝圈loop a line 环路法连接线路horizontal spindle 轴式vertical spindle 立轴式travelling-column 行程立柱feedback unit 反馈单元machining center 加工中心tool-storage 刀具存贮ball screw 滚珠丝杠tool changer 刀库machine control unit (MCU) 机床控制单元flexible machining system 柔性制造系统disk operating system (DOS) 磁盘操作系统Microsoft dish operating ssytem (MS-DOS) 微软磁盘操作系统program and data files 程序和数据文件internal and external command 内部和外部文件format a diskette 磁盘格式化diskcopy command 磁盘拷贝命令erase (deletion) command 删除命令create (change, remove) directory 建立(改变，移动)目录hard disk drive (HDD) 硬盘驱动器hard (soft) disk 硬(软)盘standard keyboard 标准键盘color display 彩色显示printer operating procedures 打印机操作程序application window 应用程序窗口batch file 批处理文件control (main,system) menu 控制(主，系统)菜单configuration system file 系统配置文件FMS (flexible manufacturing system) 柔性制造系统CNC (computer numerical control) 计算机数字控制revised feed signal 反进给信号default selection mode 默认选择模式MCU (machine control unit) 控制加工单元ACS (adaptive control system) 自动补偿系统CRT (cathode-ray tube) 显像管process planning 制定工艺过程CIM (computer integrated manufacturing) 计算机集成制造vertical stroke 垂直行程system variable 系统变量accurate die casting 精密压铸air bend die 悬空弯曲模具blank through dies 漏件式下了模calendering 压延成形center gated mold 中心浇口式模具cold chamber die casting 冷室压铸compacting molding 粉末压出成形double stack mold 双层模具duplicated cavity plate 复板模encapsulation molding 注入成形expander die 扩径模family mold 成套制品模具fantail die 扇尾形模具fantail die 鱼尾形模具f;ash mold 溢料式模具flash mold 溢料式模具flange bending die 弯缘模具flang trim die 整缘磨具flash trimming die 整缘磨具flat edge teim die 水平整缘磨具foam frming 发泡成形gang die 成排模具gravity casting 重力铸造sand mold casting 砂模铸造sectional die 对合模具shaper 定型模具singe cavity mold 单腔模具squeeze casting die 高压铸造squeezing casting die 挤压模swaging 挤锻tandem die 串列模具shree plates mold 三板式模具transfer molding 传送成形universal mold 通用模具warn foring 温锻air vent valve 通气阀anchir pin 锚梢angular cams 角凸轮angular pin 交梢(倾斜梢) baffle 调节阻板baffle plate 折流档板ball button 球塞套ball plunger 定位球塞binder plate 压板ball silder 球塞滑块binder plate 压板blank holder 防皱压板blanking punch 下料冲头bottom board 浇注底板bottom plate 下固定板bracket 托架casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁/模腔) cavity adaptor plate 固定侧安装板cavityplate 模仁板cavity retainer plate 模穴托板clamping block 锁定块cooling manifold 冷却歧管core adaptor plate 可动侧安装板core plate 心型板core push back spring 心型回位弹簧diaphragm gate 盘形浇口die approach 模头料道die clamper 夹模器die fastener 模具固定用零件die plate 冲模板direct gate 直接浇口draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejector pad 顶出垫ejector plate 顶出板ejector valve 顶出阀calendaring molding 压延成形powder metal forging 粉末锻造rotary forging 回转锻造rotational molding 离心成形shell casting 壳模铸造foam forming 发泡成形hot chamber die casting 热室压铸warmforging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱腊铸造matched mould thermal forming 对模热成形模landed plunger mold 有肩柱塞式模具landed positive mold 有肩全压式模具loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具manifold die 分歧管模具modular mold 组合式模具multi-cavity mold 多模穴模具multi-gate mold 复式浇口模具palletizing die 叠层模plaster mold 石膏模fishtail die 鱼尾形模具protable mold 手提式模具lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具single cavity mold 单腔模具three plates mold 三片式模具air vent vale 通气阀anchor pin 锚梢ball slider 球塞滑块cooling spiral 螺旋冷却栓ejection pad 顶出衬垫ejector leader busher 顶出导梢衬套film gate 薄膜形浇口finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘销flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate land 浇口面guide plate 导板guide rail 导轨head punch 顶镦冲头headless punch 直柄沖头heavily tapered solid 整体模蕊盒impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套knockout bar 脱模杵land 合模平坦面land area 合模面locating center punch 定位中心冲头locating pilot pin 定位导梢locking plate 定位板makingdie 打印冲子manifold block 歧管档块master plate 靠模样板match plate 分型板mold base 塑胶模座mold clamp 铸模紧固夹mold platen 模用板moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paring line分模线parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pin gate 针尖浇口plate 衬板rack 机架rapping rod 起模杆retainer pin 嵌件梢retainer plate 托料板slagriser 冒渣口spacer block 间隔块spacer ring 间隔环square key 方键square nut 方螺帽square thread 方螺纹stop collar 限位套straight pin 圆柱销stripper plate 剥料板submarine gate 潜入式浇口support pillar 支撑支柱/頂出支柱supporting plate 扥板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/锥形梢three start screw 三条螺纹tie bar 拉杵tunnel gate 隧道形浇口wortle plate 拉丝模板3D coordinate measurement 三次元量床boring machine 搪孔机cnc milling machine CNC铣床contouring machine 轮廓锯床copy grinding machine 仿形磨床copy lathe 仿形车床copy milling machine 仿形铣床copy shaping machine 仿形铇床cylindrical grinding machine 外圆磨床die spotting machine 合模机drilling machine 钻孔机engraving machine 雕刻机engravingE.D.M. 雕模放置加工机form grinding machine 成形磨床graphite machine 石墨加工机horizontal boring machine 卧式搪孔机horizontal machine center 臥式加工制造中心internal cylindrical machine 內圆磨床lap machine 研磨机machine center 加工制造中心NC drilling machine NC钻床NC grinding machine NC磨床NC lathe NC车床NC programming system NC程式制作系统planer 龙门铇床profile grindingmachine 投影磨床radial drilling machine 旋臂钻床surface grinder 平面磨床try machine 试模机turret lathe 转塔车床universal tool grinding machine 万能工具磨床vertical machine center 立式加工制造中心autocollimator 自动准直机bench comparator 比长仪block gauge 块规calibration 校准caliper gauge 卡规check gauge 校对规clearance gauge 间隙规comparator 比测仪cylinder square 圆筒直尺depth gauge 测深规dial indicator 针盘指示表dial snap gauge 卡规digital micrometer 数位式测微计feeler gauge 测隙规gauge plate 量规定位板height gauge 测高规inside calipers 內卡钳limit gauge 限规morse taper gauge 莫氏锥度量规optical flat光学平晶optical parallel 光学平行passimeter 內径仪position scale 位置刻度protractor 分角器radius 半径ring gauge 环规sine bar 正弦量规snap gauge 卡模square master 直角尺telescopic gauge 伸缩性量规working gauge 工作量規aluminium alloy 铝合金钢bearing alloy 轴承合金clad sheet 被覆板ferrostatic pressure 钢铁水静压力galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高強度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材prehardened steel 顶硬钢stainless steel 不銹钢tin plated steel sheet 镀锡铁板vinyl tapped steel sheet 塑胶覆面钢板age hardening 時效硬化ageing 老化处理air hardening 气体硬化air patenting 空气韧化annealing 退火anode effect 阳级效应anodizing 阳级氧化处理atomloy treatment 阿托木洛伊表面austempering 奧氏体等温淬火austenite 奧斯田体/奧氏体bainite 贝氏体banded structure 条纹状组织barrel plating 滾镀barrel tumbling 滾筒打光blackening 染黑法box annealing 箱型退火box carburizing 封箱渗碳bright electroplating 辉面电镀bright heat treatment 光辉热处理bypass heat treatment 旁路热处理carbide 炭化物carburized case depth 浸碳硬化深层carburizing 渗碳chemical plating 化学电镀chemical vapor deposition 化学蒸镀coarsening 結晶粒粗大化coating 涂布被覆controlled atmosphere 大气热处理creeping discharge 蠕缓放电decarburization 脱碳处理decarburizing 脱碳退火depth of hardening 硬化深层diffusion annealing 扩散退火electrolytic hardening 电解淬火first stage annealing 第一段退火flame hardening 火焰硬化flame treatment 火焰处理full annealing 完全退火gaseous cyaniding 气体氧化法globular cementite 球状炭化铁grain size 結晶粒度granolite treatment 磷酸溶液热处理graphitizing 石墨退火hardening 硬化heat treatment 热处理hotbath quenching 热浴淬火induction hardening 高周波硬化ion carbonitriding 离子渗碳氮化ion carburizing 离子渗碳处理ion plating 离子电镀low temperature annealing 低温退火malleablizing 可锻化退火martempering 麻回火处理martensite 马氏体/硬化铁炭metallikon 金属噴镀法metallizing 真空涂膜nitrocarburizing 软氮化normalizing 正常化overageing 过老化overheating 过热pearlite 针尖组织phosphating 磷酸盐皮膜处理physical vapor deposition 物理蒸镀plasma nitriding 离子氮化pre-annealing 预备退火precipitation 析出precipitation hardening 析出硬化process annealing 制程退火quench ageing 淬火老化quenchhardening 淬火quenching crack 淬火裂痕recrystallization 再结晶residual stress 残留应力retained austenite 残留奧salt bath quenching 盐浴淬火sand blast 喷砂处理seasoning 時效处理second stage annealing 第二段退火secular distortion 经年变形segregation 偏析selective hardening 部分淬火shot blast 喷丸处理single stage nitriding 等温渗氮soaking 均热处理solution treatment 固溶化热处理stabilizing treatment 安定化处理straightening annealing 矫直退火strain ageing 应变老化stress relieving annealing 应力消除退火subzero treatment 生冷处理surface hardening 表面硬化处理tempering crack 回火裂痕thermal refining 调质处理thermoechanical treatment 加工热处理transformation 变态under annealing 不完全退火vacuum carbonitriding 真空渗碳氮化vacuum carburizing 真空渗碳处理vacuum hardening 真空淬火vacuum heat treatment 真空热处理vacuum nitriding 真空氮化water quenching 水淬火broing machine 搪孔机CMC milling machine CMC铣床wolfrtam (W) 钨vanadium (V) 钒uranium (U) 铀titanium (Ti) 钛tkallium (Ti) 铊tantalum (Ta) 钽stannum (Sn) 锡scandium (Sc) 钪samarium (Sm) 钐driling machine 钻孔机graphite mackine 石墨加工机praner 投影磨床radial driling machine 旋臂钻床bench comparatcr 比长仪feeler guage 测隙规guage plate 量规定位板height guage 测高规morse taper guage 莫氏锥度量规nano 奈米(十亿分之一) plug guage 塞规thickness gauge 厚薄(测隙)规low alloy tool steel 特殊工具钢maraging steel 马式体高强度热处理钢mateix alloy 马特里斯合金meehanite mttal 米汉纳铁perhardened steel 预硬钢ageing treatment 老化处理austepeering 奥氏体等温淬火bright heat treatement 光辉热处理bypass heat treament 旁路热处理diffusion annealing 扩散退火acetylene 乙炔ampere 电流安培angel welding 角焊arc 电弧argon arc welding 氩弧焊接bare electrode 光熔焊接camber 电弧弯曲cascade 階叠熔接法clad weld 被覆熔接crator 焊疤excess metal 多余金属gas shield 气体遮蔽hand face shield 手握面罩hard facing 硬表面堆焊laser beam welding 雷射光焊接metal electrode insert gas welding MIG 熔接overlaying 堆焊propane gas cutting 丙烷气切割seam 焊缝seaming 接合seam welding 流缝熔接series seam welding 串联缝熔接spark 火花stud arc welding 电弧焊接underlaying 下部焊层weld flow mark 焊接流痕weld mark 焊接痕weld penetration 熔接透入welding bead 焊接泡welding interval 焊接周期activator 活化剂adapter ring 接模环bag moulding 气胎施压成形bank 滞料breathing 排气caulking compound 填隙料color masterbatch 色母料color matching 调色colorant 着色剂daylight 开隙elastomer 弹性体extruded bead sealing 压出粒涂层法floating platen 活动模板foaming agent 发泡剂granule 颗粒料hot mark 热斑hot stamping 烫印kiss-roll coater 滚压涂布机kneader 混合机knife coating 刮刀涂布levelling agent 匀涂剂lubricant 润滑剂mandrel 模心型master batch 母料matrix 基料molecular 分子筛mould clamping force 锁模力mould release agent 脱模剂over packing 过充填oxidation 氧化parison 吹气成形坯料pin point gate 针孔形浇口plasticizer 塑化剂plastomer 塑体plating 电镀ram 冲柱ram extruder 活塞式押出机reciprocating screw 往复螺杆restricted gate 限制形浇口sealer 封口机side gate 侧向浇口slip agent 光滑剂snap fit 滑入配合spanishing 凹痕印刷spray up 喷附成形staple fiber 短纤维strain 应变strand 丝束stress cracking 应力龟裂take out device 取料装置toggle type mould clamping system 肘杆式锁模装置torpedo spreader 鱼雷形分流板transparency 透明性under coat 打底突层Steam trace 加热蒸汽管道branch connection 分支接续fabrication tolerance 制造容差threaded pipe 螺纹管seal welding 密封焊接flange joint 凸缘接头seal fitting 密封接头, 密封配件Screw thread lubricant 螺纹润滑剂Seal 绝缘层lock washer 锁紧[止动, 防松]垫圈electrical panel 配电板,配电盘zinc plated 镀锌的National Electrical Code 全国电气规程master schedule 主要图表, 综合图表, 设计任务书,主要作业表flange connection 凸缘联接Hard hat 安全帽packing list 装箱单crate 柳条箱purchased material list 原材料进货单back-feed 反馈NPT thread 美国标准锥管螺纹cable gland 电缆衬垫terminal block 线弧, 接头排接线盒, 接线板, 线夹insulated sleeve 绝缘套管wire terminal 电线接头motor lead 电动机引出线orifice plate 挡板flange gasket 法兰垫片dimensional inspection 尺寸检验ABS resin 丙烯轻丁二烯苯乙烯树脂arcylic 压克力acetal copolymer 共聚甲醛acetal resin 聚甲醛树脂acetone resin 丙酮树脂acrylic fiber 丙乙轻纤维acrylic resin 丙烯树脂acrylonitrile-styrene 丙乙轻苯乙烯树脂additional polymer 加聚物adhesive 粘着剂adhesive film 粘着薄膜alkyd resin 醇酸树脂allyl resin 烯丙醇酯树脂amino resin 氨基树脂butadiene 丁二烯butyl acetate 醋酸丁酯carbon fiber 碳纤维catalyst 催化剂cellulose acetate 醋酸纤维素(CA) cellulose acetate butyrate 醋酸丁酸纤维素chlorinated polyethylene 氯化聚乙烯chopped strand 短玻璃丝束crystalline polymer 结晶性聚合物cyclohexanone 环乙酮cyclohexanol 环乙酯dially phthalate 苯二甲酸二烯丙酯dibutyl fumarate 反丁烯二酸二丁酯dioctyl fumarate 反丁烯二酸二辛酯engineering plastics 工程塑胶ethyl acetate 醋酸乙酯ethylene vinylacetate 乙烯-醋酸乙烯共聚物expanded polystyrene 发泡聚苯乙烯fibrillation 原纤化filament 长纤维fluorocarbon resin 氟碳树脂graphite fiber 石墨纤维high impact polystyrene 高冲击聚苯乙烯(HIPS) high impact polystyene 高冲击产聚苯乙烯melamine resin 三聚氰胺酚醛树脂mylar 聚乙烯对苯二酸oxirane 环氧乙烷plastic 塑料polyacetal 聚甲醛polyacetylene 聚乙炔polyacrylic acid 聚丙烯酸(PAP) polyalcohol 多元醇polyamide 耐龙(PA) polybutyleneterphthalate 聚对苯二甲酸丁酯polycarbonate 聚碳酸酯polyethylenterephthalate 聚乙醇对苯(PETP) polymetylmethacrylate 聚甲基丙烯酸甲酯addendum of thread 螺牙冠adjustable spaneer 活动扳手angle cutter 角铣刀approaching face 渐近面arbor 心轴back clearance angle 背隙角back rake 背斜角backing 视垫ball end mill 球端铣刀belt sander 带式打磨机bevel angle 去角bevel lead 倒角blade 刀刃blank 胚料bottoming hand tap 底螺丝攻brazed tool 硬锝刀具centering location 定心ceramic tool 陶瓷刀具chamfer 倒角chamfered corner 去角角隅chamfering machine 倒角机chamfering tool 去角刀具chaser 螺丝钣刀chip breaker 断屑器clamp face 夹持面clearance angle 隙角cold circular saw 常温圆规compass 两角规concave angle 凹角concave cutter 凹面铣刀corner radius 角隅半径cotter diameter 梢径crack 破裂crater 刀痕磨耗crest radius 牙顶圆角半径cutting edge angle 切深角cutting edge inclination 切刃斜角cylinder key broach 键孔拉刀drawing thread 退刀螺蚊end cutting angle 副切深角end gash 刀端深口face 斜面face milling cutter 面铣刀flaking 破损flank 隙面(刀腹) flank wear 隙面磨耗fluted land 槽背gear hob 滚齿hatching 部面线helix angle 螺旋角hexagon headed bolt 六角头螺栓hexagon nut 六角螺帽hook angle 勾角included angle 刀刃角index head 分度头jack 千斤顶lapping 研磨lead 导程machinability 被切削性major cutting edge 主切刃major flank 主隙面margin 刀缘metal saw 金工锯metal slitting saw 锯割铣刀minor flank 副隙面no relief thread 无隙螺纹normal clearance angle 法隙角normal rake 法斜角normal wedge angle 法刀口角nose angle 刀角nut tap 螺帽螺丝攻orthogonal clearance angle 垂直隙角orthogonal rake 正斜角orthogonal wedge angle 垂直刀口角pearn tap 特殊螺丝攻plain milling cutter 平铣刀plain tapered bore 普通推拔孔plug hand tap 塞螺丝攻polot tap 导桿螺丝攻pull head 拉头pulley tap 带轮螺丝攻radial 径向斜面radial thread relief 径向螺牙隙radius end mill 圆角端铣刀radius of circle 圆角rake angle 斜角ratchet broach 刺轮拉刀retrieving head 支持头rifle broach 来福线拉刀sand paper 砂纸scraper 刮刀segment angle 弧角serration broach 细齿拉刀shank 刀柄side clearance angle 侧隙角side rake 侧斜角slab milling cutter 平板铣刀spade drills 铲钻spanner 扳手spline broach 方栓槽拉刀square 直角尺square end mill 方形端铣刀square sleeker 方形镘刀square trowel 直角度straight bore 直孔straight flute 直尺槽straight shank drills 直柄钻头subland drills 多槽钻头super crest tap 高顶螺丝攻tap 螺丝攻taper hand tap 斜螺丝攻taper shank 推拔柄taper tap 推拔螺丝攻tapping torque 攻螺丝扭力target drills 留心钻thread 螺纹thread milling cutter 螺纹铣刀threads per inch 牙数throw away tip 折叠式刀片throw away tool 折叠式刀具tool angles 刀具角tool for lathe 车刀tool point angle 刀刃角tool reference plane 基准面tosecan 画线盘waffle die flattening 压文效平working angles 切削刀barrelling 滚光加工blanking 下料加工cam die bending 凸轮弯曲加工double shearing 叠板裁断drawing 引申加工drawing with ironing 抽引光滑加工fine blanking 精密下料加工finish blacking 光制下料加工flabging 凸缘加工impact extrusion 冲击挤压加工lock seaming 固定接合marking 刻印加工parting 分段加工progressive blanking 连续下料加工progressive drawing 连续引申加工reaming 铰孔加工scrapless machining 无废料加工shaving 缺口修整加工shearing 切断加工staking 铆固stamping 锻压加工accumulator 蓄压器actuator 驱动器adapter 接头back shaft 支撑轴blank determination 胚料展开board drop hanmmer 板落锤brake 煞车camlachie cramp 铸包casting on flat 水平铸造chamotte sand 烧磨砂charging hopper 加料漏斗clutch brake 离合制动器coil car 带卷升降运输机coil cradle 卷材进料装置coil reel stand 钢材卷料架cradle 送料架crank 曲柄轴crankless 无曲柄式cross crank 横向曲轴dial feed 分度送料die assembly 合模double crank press 双曲柄轴冲床film play 液面花纹fine blanking press 精密下料冲床formboard 进模口架frame 床身机架机械专业英语词汇(一) 金属切削metal。
机械制造中英双语对照
车床 螺栓 螺母
angle bar angle bar channel bar channel bar H-beam spot facing machining drill chamfer lathe bolt nut
垫圈
washer
垫圈 六角螺栓 六角螺母
盘头螺钉 埋头螺钉 木螺钉
washer hexagon head bolt hexagon nut pan head screw countersunk flat head screw tapping screw
挤压加工 落料 穿孔 拉深
压筋 冲缘加工 压印加工 冲孔 薄板
胶着
配合
fitting
高强度钢
质量 比重
mass relative density
弹性变形回复 粘住
金属
metal
复合材料
腐蚀 零件
corrosion part
延展性 废料
收缩
shrink
冲头
膨胀 密封 缺陷 合金
铸铁
软钢 黄铜 青铜 英寸
cross-joint
union
加速度 正火 淬火 回火 退火 应变 焊接 表面粗糙度 铝 铜 钢管 键 公差 间隙配合 过渡配合 过盈配合 法兰 应力集中
轮毂
热压配合 磨床 拉伸强度 屈服点
acceleration normalizing quenching tempering annealing strain weld surface roughness aluminium copper steel tube key tolerance clearance fit transition fit interference fit flange stress concentration
机械加工常用刀具英汉对照
书山有路勤为径，学海无涯苦作舟机械加工常用刀具英汉对照adjustable spanner 活动扳手angle cutter 角铣刀anvil 铁arbour 心轴backing 衬垫belt sander 带式打磨机buffing 抛光chamfering machine 倒角机chamfering tool 去角刀具chisel 扁錾chuck 夹具compass 两角规concave cutter 凹面铣刀convex cutter 凸形铣刀cross joint 十字接头cutting edge clearance 刃口余隙角drill stand 钻台edge file 刃用锉刀file 锉刀flange joint凸缘接头grinder 砂轮机hammer 铁锤hand brace 手摇钻hatching 剖面线hexagon headed bolt 六角头螺栓hexagon nut 六角螺帽index head 分度头jack 千斤顶jig 治具kit 工具箱lapping 研磨metal saw 金工锯nose angle 刀角pinchers 钳子pliers 铗钳plug 柱塞头polisher 磨光器protable driller 手提钻孔机punch 冲头sand paper 砂纸scraper 刮刀screw driver 螺丝起子scribing划线second out file 中纹锉spanner 扳手spline broach 方栓槽拉刀square 直角尺square sleeker 方形镘刀square trowel 直角度stripping 剥离工具T-slotT 形槽tool for lathe 车刀tool point angle 刀刃角tool post 刀架tosecan 划线盘trimming 去毛边waffle die flattening 压纹效平wiper 脱模钳wrench 螺旋扳手tips:感谢大家的阅读，本文由我司收集整编。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
三、PLC控制的随机选刀方式的研究 刀库的自动控制指CNC执行用户指令后系 统对刀库的自动控制过程，包括程序找刀和 自动换刀[(63,71]。加工中心的计算机数 控装置(CNC)发出的选刀指令，将刀库转 到所需刀具号的取刀位置，称自动选刀。自 动选刀有两种方法:顺序选刀和随机选刀方 法 这两种选刀都是根据plc编程来实现的
一、系统组成及其控制结构
2、电气控制系统
本刀具储存系统的电气控制主要是对其货架进行运行控制和位置控制。运行控制包括运 行设备的启动、制动控制。位置控制主要是对货架位置和地址进行检测。
1)电气传动 水平旋转刀具储存系统各机械的动作都属于 反复短时工作制。而且系统在运行时需要几种速度, 因此 传动系统需要调速, 所以该系统选用了变频调速的方法, 可 以采用结构简单、运行可靠的变频器和变频电动机。 2)控制方式 该系统分为手动和自动控制2 种控制方式, 手动控制一般作为调试用和备用的工作方式; 自动控制方 式为本系统计算机(IPC)和控制单元(变频器、接触器等) 组成的一个自动控制系统。 3)位置及定位精度检测 本系统中自动认址和位置检测采 用了接近开关作为检测元器件, 通过光点隔离继电器板和 记数板对接近开关采集的信号进行记数和运算处理, 采用 最优路径寻址方式确定货架的当前位置和货架的目的位置 。为了使系统定位更准确, 采用了 2 只光电开关, 分别检 测2 个货架的2 Nhomakorabea检测片。
3、刀具库的功能及种类
1、功能：刀库的作用是储备一定数量的刀具，机械手实 现主轴上刀具的互换刀具的类型有盘式刀库、链式刀库等 多种形式，刀库的形式和容量要根据机床的工艺范围来确 定
2、种类
a转塔式刀库
b盘式刀库
特点:适用于刀库容量较大的场合，所占的空间小，一般适用于 刀具数在30-120把。仅增加链条长度即可增加刀具数，可以 不增加圆周速度其转动惯量不像盘式刀库增加的那样大。
自我介绍
The design of machinery let me know how to design a belt, a chain, a spur gear, worm and worm gears, bearings, shaft, coupling and a system using all of them. I have learnt a lot from it not only how to do research , but also team sprit and how to communication with others .So I love my major. I am long for doing research in this field. However,
2、带刀式自动换刀系统
带刀库的换刀装置由刀库、选刀机构、刀具自动装卸机械及刀具交 换机构(机械手)等四部分组成，应用广泛。刀库机械手自动换刀系统， 整个换刀过程比较复杂。首先要把加工过程中使用的全部刀具安装在标 准刀柄上，在机外进行尺寸预调后，按一定的方式放入刀库。换刀时， 先在刀库中选刀，再由换刀装置从刀库或主轴上取刀，进行交换，将新 刀装入主轴，旧刀放回刀库。
二、换刀装置的主要类型,特点
1、类型 （1）自动回转刀架 自动回转刀架是数控机床上使用的一种简单的 自动换刀装置，有四方刀架和六角刀架等多种形 式，回转刀架上分别安装有四把、六把或更多的 刀具，并按数控指令进行换刀。回转刀架又有立 式和卧式两种，结构比较简单，适用于经济数控 车床。
接到换刀指令后，机床控制系统便将主轴控制到指定换刀位置;与此同时，刀具 库运动到适当位置，换刀装置回转并同时与主轴、刀具库的刀具相配合;拉杆从 主轴刀具上卸掉，换刀装置将刀具从各自的位置上取下;换刀装置回转180º 并将 主轴刀具与刀具库刀具带走;换刀装置回转的同时，刀具库重新调整其位置，以 接受从主轴取下的刀具;接下来，换刀装置将要换上的刀具与卸下的刀具分别装 入主轴和刀具库:最后，换刀装置转回原“待命”位置。至此，换刀完成，程序 继续运行。
1、文章标题
Tool Library of the General Armament Department and Control System Design 机床刀具库的总装与控制系统 设计
2、摘要
该系统采用最优化技术, 利用计算机存储的 大量库存信息, 能及时、准确、全面地反映 刀具库的库存情况。整个系统采用图形界面 , 人机对话由中文菜单提示, 可实现各种功 能选择和各种信息的输入。管理系统采用在 线帮助功能。可通过车间管理层、网络系统 实现信息管理和共享。具有自动库存管理、 刀具入库管理、刀具出库管理和统计查询功 能。自动换刀系统将以较快的速度增长，缩 短换刀时间，提高刀具的定位精度是重要的 手段，有利于数控技术的发展。
谢谢！
机 械 工 程 学 院
自我介绍
My name is yyy .I was a character cheerful boy，so my hobbies is extensive. In my spare time, I like to read books, listen to Pop music, watch movies and doing sports. In all sports , volleyball is my favorite. They keep me in good health, full of energy and breed optimism towards life. Besides, I really enjoy watching English films. It can not only kill time, but also excise my listening skills. I know my English is not good enough, and I will continue to study.
（1)驱动机构 该系统选用了变频调速的方法。采用锥形制动电机, 带变 频调速, 经摆线针轮减速器, 通过链轮传动 （2）拖动与传动系统 采用变频控制技术。通过变频调速, 可使传动轴 转速在正常范围内调节使刀架回转速度控制到 5～ 30mm in, 2 个 传动轴各带上、下2 个链轮通过上、下2 条异形滚子链带动货架转动 （3）刀架与防护罩 整库共有14 列独立刀架。其中 13 列为插座式 刀架, 1 列为抽屉式刀架, 每个刀架背部通过销轴与上、下输送链链板 联接, 底部安装滚轮, 链条转动带动刀架沿地轨转动。
总结
重点讨论了在当 今制造环境下刀 具存储与管理新 的模式和方法。
制造出具有自动 库存管理、刀具 入库管理、刀具 出库管理和统计
查询功能。
短路径定位、主 轴换刀， 而且不支持大型 刀具。
一、系统组成及其控制结构
1、机械结构及工作原理 刀具库由支架、驱动机构、传动系统、刀架、护 罩、电气控制系统等部分组成。支架由立柱、横 梁、上下导向环轨、支撑地轨组成。
自我介绍
I think further study is urgent for me to realize my dream. I think the postgraduate study can enrich my knowledge and make the competence in my future career.
自我介绍
Speaking of my undergraduate major mechanical design, manufacturing and automation, I love that because through this major I’ve learned a lot of things. [For instance, theoretical and material mechanics tell me how to analyze the forces implemented on all kinds of objects and how to solve mechanic problems with so many fabulous methods. The principle of mechanics tells me how to turn a fourbar linkage mechanism into a slidecrank mechanism and many other things.
3、主要内容
系统组成及其控制结构
讲述了）
内容一
内容二
换刀装置的主要类型和特点
PLC控制的随机选刀方式的研究
内容三
4、引 言
研究背景
机床原来的刀 库控制程序是 单独设计的， 没有采用刀具管 理系统，功能也 比较单一， 只实现了刀库刀 具的找刀、刀库 最
目的
创新点
该系统采用最 优化技术, 利用 计算机存储的 大量库存信息, 能及时、准确 、全面地反映 刀具库的库存 情况