XHB连接器图纸
海湾消防模块安装接线示意图(整理齐全)
海湾100B声光报警器安装接线示意图HX-100B声光报警器是海湾报警系统最为常用的一个产品，今天海湾消防设备工程师将为大家讲解海湾100B声光报警器安装示意图和接线示意图。
海湾100B火灾声光警报器外形示意图如图2-19：HX-100B火灾声光警报器采用壁挂式安装，在普通高度空间下，以距顶棚0.2m处为宜。
火灾声光警报器接线端子示意图如图2-20：其中：Z1、Z2：与火灾报警控制器信号二总线连接的端子，对于HX-100A型火灾声光警报器，此端子无效D1、D2：与DC24V电源线连接的端子，无极性S1、G：外控输入端子可以利用手动火灾报警按钮的无源常开触点直接控制编码型的火灾声光警报器启动，系统接线示意图如图2-21：布线要求：信号二总线Z1、Z2采用阻燃RVS型双绞线，截面积≥1.0mm2；电源线D1、D2采用阻燃BV线，截面积≥1.5mm2；S1、G采用阻燃RV线，截面积≥0.5mm2。
HX-100B/T火灾声光警报器信号总线和电源线与警报器底壳端子连接处应做密封处理（这种方式中，消火栓按钮按下，O、G端输出DC24V电源，可直接控制消防泵的启动，泵运行后，泵控制箱上的无源动作触点信号通过I、G端返回按钮，可以点亮按钮上的绿色回答指示灯。
当设备启动电流大于100mA时，应通过GST-LD-8302切换模块进行转换，通过GST-LD-8302转换直接启泵方式应用示意图如图2-14所示：海湾消防按钮接线及应用示意图海湾报警之家 / 2012-10-16海湾报警之家工程师本节将为大家讲解海湾消防按钮的接线示意图，海湾消防报警按钮常用型号有：J-SAM-GST9121和J-SAM-GST9122两种。
一、J-SAM-GST9121海湾消防按钮接线示意图手动火灾报警按钮外接端子示意图如图2- 7。
其中：Z1、Z2：无极性信号二总线接线端子。
K1、K2：额定DC30V/100mA无源常开输出端子，当报警按钮按下时，输出触点闭合信号，可直接控制外部设备。
安装工程中各种管道常用连接方式现场图片及说明
安装工程中各种管道常用连接方式现场图片及说明PPR与PE管道连接PE管道与PPR连接，黑色部分是PE变径弯头前面接PE管道，黄管道上图分解，黑色的配件为外螺纹直截了当，一边与PE热熔连接，阀门上方为PE管道DN50，下方为PPR管道，中间通过一个阀门连为两个外螺纹直截了当PE与法兰阀门连接，使用管径较大的管道连接，法兰两边可连接或同种管道PE与UPVC管道连接，所用的配件与图2相似镀锌钢塑管与阀门连接上图局部放大，闸阀与止回阀连接消防信号阀与DN150镀锌钢管连接水泵接合器与消防管道采纳法兰连接DN100的消火栓管用机械三通分支机械四通，DN150主管两边接喷淋支管消防管道中大于100的管道采纳沟槽配件〔卡箍〕连接消防管道的卡箍连接对夹式蝶阀与消防管道采纳法兰连接铜管与阀门连接，铜管一样采纳焊接PE钢丝管网采纳电容连接，图示电熔机热熔机彩铝檐沟管〔铝管〕属于金属管道，接口用承插打胶湿式报警阀连接水泵吸水管阀门连接HPDE双壁波浪管HPDE双壁波浪管采纳橡胶圈连接，留意橡胶圈下面是详细的说明1 管道丝扣连接(镀锌钢管、衬塑镀锌钢管)1 断管：依照现场测绘草图，在选好的管材上画线，按线断管。
a 用砂轮锯断管，应将管材放在砂轮锯卡钳上，对准画线卡牢，进手柄用力要平均，不要用力过猛，断管后要将管口断面的铁膜、毛b 用手锯断管，应将管材固定在压力案的压力钳内，将锯条对准画条要保持与管的轴线垂直，推拉锯用力要平均，锯口要锯到底，不防管口断面变形。
2 套丝：将断好的管材，按管径尺寸分次套制丝扣，一样以管径次，40-50mm者套丝3次，70mm以上者套丝3-4次为宜。
a 用套丝机套丝，将管材夹在套丝机卡盘上，留出适当长度将卡盘码，上好板牙，按管径对好刻度的适当位置，紧住固定扳机，将润开机推板，待丝扣套到适当长度，轻轻松开扳机。
b 用手工套丝板套丝，先松开固定扳机，将套丝板板盘退到零度，把板盘对准所需刻度，拧紧固定扳机，将管材放在压力案压力钳内紧，将套丝板轻轻套入管材，使其松紧适度，而后两手推套丝板到侧面扳套丝板，用力要平均，待丝扣立即套成时，轻轻松开扳机丝扣应有锥度。
xbox360接头图纸
XBOX 360 Motherboard Headersand ConnectorVersion 1.4DisclaimerThe information contained in this document was obtained from the public domain and/or my own reverse engineering and is provided in good faith but no warranty can be made for its accuracy. Any opinions expressed are entirely those of myself and cannot be taken to represent the views of past, present or future employers.I do not support piracy or the illegal copying of copyright material. I'm only seeking the ability to run custom software and push the hardware to it's maximum potential. Remember that a profitable game industry will guarantee us all amazing products for the future.If you notice something incorrect or have any comment, please feel free to contact me.Speedy22xbox.360@IntroductionMost of the information was based on the top and bottom layers of a dechipped 360 motherboard and decapped chips, I will update the information once I gain full knowledge of the inner layers of the motherboard.For reference, I have also included some information I have gathered from images of Development Hardware and XDK hardware found on the net.Please double-check my information, I am human and I do make mistakes. I have also attempted to give credit where credit was due. If you find any errors or omissions, please let me know so that I can correct it on future versions.Like most, I am doing this as a hobby in my spare time, so I will do my best to keep the information up to date but I can not make any guarantees.I am currently looking for a supplier/manufacturer for the following components;Controller Headset PortBoth the Male and FemaleConnector.Memory Card PortMale Connector(On Memory Card)RF Module PortMale Connector(On RF Module)Hard Drive PortMale Connector(On Hard Drive)My current employment position will be changing in the near future, so I will be open for new opportunities. I am a Canadian citizen living in Waterloo, ON, Canada with a background in Electronics Engineering and Management. Feel free to contact me for more details.Speedy22xbox.360@Table of ContentMotherboard Block Diagram . . . . . . . . . . . . . . . . 2 J1A1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 J2A1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 J3A1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 J9A1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 J9A2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 J2B1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 J1C1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 J5C1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 J5C2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 J8C1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 J1D1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 J1D2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 J2D1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 J2D2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 J1E1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 J1F1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 J7F1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 J3G1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 J6G1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 J7G1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 J7G2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 J9G1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 AppendixDocument Changes . . . . . . . . . . . . . . . . . . . . 25 Unique per Console Numbers . . . . . . . . . . . . . . .26 Retail Motherboard Differences . . . . . . . . . . . . . . 27 Dashboard Updates . . . . . . . . . . . . . . . . . . . . .28 System Requirements . . . . . . . . . . . . . . . . . . .29 Retail Block Diagram . . . . . . . . . . . . . . . . . . . .30 XeDK Block Diagram . . . . . . . . . . . . . . . . . . . .31 HDK Block Diagram . . . . . . . . . . . . . . . . . . . . .32 Memory Map . . . . . . . . . . . . . . . . . . . . . . . .33 CPU Pinout (BGAout) . . . . . . . . . . . . . . . . . . . .34 GPU Pinout (BGAout) . . . . . . . . . . . . . . . . . . .35 Southbridge Pinout (BGAout). . . . . . . . . . . . . . . .36Detailed Motherboard Block Diagram Not in this Public Release10/100 Base-T Ethernet and USB Port1Green LED9RD+2Green LED10CT3Yellow LED11RD-4Yellow LED12+5 VDC5TD+13Data -6CT14Data +7TD-15GND8Shield GND16Pin 9 J6G1Manufacturer: Bel Stewart ConnectorsProduct Name and #: Magjack SI-80039-FNotes:Green and Yellow LEDs are not present, but all the connection are available on the 360 Motherboard. (Version 11)LEDs are present on the 360's XDK motherboard. (Version 9)Pin 16 connects to Pin 9 of J6G1 the RF Module.Video and Audio Port1Red Gnd 2Green Ground3Red (Cr in HDTV mode) 4Green (Y in HDTV mode) 5Composite Gnd 6Blue Ground7Composite (Sync in RGB mode) 8Blue (Cb in HDTV mode) 9H-sync Gnd 10V-sync Gnd11H-sync (VGA Mode) 12V-sync (VGA Mode)13Audio-R Gnd 14Audio-L Gnd15Audio-R 16Audio-L17Switching voltage (for SCART pin-8) 18CBL-ID119Blanking Signal (for SCART pin-16) 20CBL-ID1.121Unknown22CBL-ID223Unknown24CBL-ID2.125Optical - Audio (SPDIF) 26CBL-ID327Optical - Gnd (SPDIF) 28CBL-ID3.129Optical - +5V 30See J2B1 or J8C1 Setting Cable ID:ID1-1.1 = VGA mode enabledID2-2.1 and ID3-3.1 = RGB (SCART) mode enabledID3-3.1 = HDTV (Y/Cb/Cr) mode enabledID2-2.1 = Composite (TV) mode enabledManufacturer: UnknownProduct: UnkownNote:Source: (corrected Pin#s and added pin 30)Fan Connector1GND Blue2V+Brown3GND Black4V+Red Manufacturer: FoxconnProduct:Note:V+ Starts at +5.4 VDC and climbs to +11.8 VDC within 30 sec of power on.DC Power Port1GND6+12 VDC2GND7Power Enable3GND8+5 VDC (Standby)4+12 VDC9Shield (GND)5+12 VDC10Shield (GND) Note:Pin 7 Turns Pins 4, 5, 6 on when it is tied to ground.Power Supply is difficult to open up. I would not recommend it.1) Remove rubber feet (they are glued in place). This will probably destroy them.2) Dig out all the glue, including the glue in the head of the philips screws.3) Remove the 4 screws.4) Remove bottom cover.5) Remove the two philips screws. One on each side of the heat sink.6) Gently wiggle circuit board out of the top cover. The DC supply side should lift up first. Heat sink grease is preventing the easy removal of the circuit board. Continue to wiggle the circuit board until the grease bond is broken.XDK DC Power1+5 VDC (Standby)2GND Manufacturer: UnknownPart #: UnknownNote:This connector is used to supply power to the extra circuitry used in the XDK (motherboard version 009).The circuitry is located in the "Sidecar" that attaches to the hard drive side of the xbox 360.J2B1XDK Debug HeaderPower ON Power Off Data Present 1RX - U2C1 pin 15D1+3.3 VDC0No 2TX- U2C1 pin 14D1+3.3 VDC0No 3NC00No 4Connects to U2C1 pin 16B+3.3 VDC+3.3 VDC No 5Eject2+3 VDC0No 6Connects to U2C1 pin 16C00No 7+3.3 VDC (Standby)+3.3 VDC+3.3 VDC No 8+3.3 VDC+3.3 VDC0No 9SDA+3.3 VDC+3.3 VDC Yes 10SCL+3.3 VDC+3.3 VDC Yes 11See Schematics+3.3 VDC+3.3 VDC No 12GND00No 13+5 VDC (Standby)+3.3 VDC+5 VDC NoNote:1) Speculation: Document posted on and suggests that these pins are UART operating at115000 bps.2) Quick pulse Ejects, otherwise 360 immediately shuts down.J1C1DVD SATA Connector1GND2A+3A-4GND5B-6B+7GNDManufacturer: TycoPart #: UnkownNote:Standard SATA interface.Each DVD drive has a unique ID key. (source: )J5C1ANA HeaderPower ON Power Off Data Present 1Connects to Pin 71 of U4B1+1.8 VDC+1.8 VDC No2Connects to Pin 70 of U4B1+1.8 VDC+1.8 VDC No3Connects to Pin 69 of U4B100No4Unknown00No5Connects to Pin 72 of U4B100No6GND 00NoJ5C2GPU SPI EEPROM HeaderPower ON Power OFF Data Present 1SCK00high on startup 2SO003SI004/WP+1.8 VDC+1.8 VDC5/CS+1.8 VDC+1.8 VDC brief activity at startup 6GND00Note:J8C1CPU JTAG HeaderPower ON Power OFF Data Present 100No2+1.1 VDC0No3+1.8 VDC+1.8 VDC0No4+1.8 VDC0No5GND00No6+1.8 VDC0No7+1.8 VDC0No8+1.8 VDC0No9+3.3 VDC+3.3 VDC No10+1.8 VDC0No Note:Images indicate this port was used during hardware development.Pin 9 was not used in HDK image.The pin header is also present on the XDK version 9 motherboard.Speculation: GPULDBG, Inputs - TDI, TMS, TCK, Output -TDO, and RESETJ1D1DVD Power Connector1NC7GND2NC8+5 VDC3Open/Close9GND4Tray Status10+12 VDC5GND11GND6+3.3 VDC12+12 VDC Manufacturer:Part #:Notes:Open/Close: momentary tied to gnd to open/close drive door. Tray Status: +3.3 VDC tray is open. 0 v tray is closed. Source: J1D2XDK Debug Header #2Power ON Power OFF Data Present 1Connects to U2C1 pin 5Y00No2Connects to U2C1 pin 5AA+3.3 VDC+3.3 VDC No3Connects to U2C1 pin 3U00No4Connects to U2C1 pin 5AB+3.3 VDC+3.3 VDC No5+5 VDC (Standby)+5 VDC +5 VDC No6GND00No7GND00No8Unknown00No9Unknown00No Note:This port is used in the XDK version 9 motherboard. The connector is routed into the XDK "Sidecar" expansion module.J2D1Southbridge HeaderPower ON Power OFF Data Present 1Connects to U2C1 pin 21V+1.8 VDC0No2Connects to U2C1 pin 22W+1.8 VDC0No3Connects to U2C1 pin 22V00No4Connects to U2C1 pin 21W00No5Connects to U2C1 pin 20W00No6GND00NoJ2D2GPU HeaderPower ON Power OFF Data Present 1Connects to U4D1 pin 12E+1.9 VDC0No2Connects to U4D1 pin 12F+1.9 VDC0No3Connects to U4D1 pin 12D00No4Connects to U4D1 pin 11G00No5Connects to U4D1 pin 13E00No6GND00No7See Note+1.9 VDC0No8Connects to U4D1 pin 13G00No Note:There are images of a XDK motherboard (version 9) on the Internet that shows a green wire connecting Pin 5 to the Southbridge(21J).Pin 7 - still working on it.J1E1Hard Drive SATA Connector1GND8GND2A+9GND3A-10GND4GND11+5 VDC5B-12+5 VDC6B+13+5 VDC7GND14+5 VDC (standby) Manufacturer: Unknown-Made in ChinaPart #: XB00351-002J1F1Southbridge LED HeaderPower ONPower OFFData Present1+5 VDC +5 VDC 0No 2GND00No 3Connects to U2C1 pin 20D +3.3 VDC0No 4Connects to U2C1 pin 21D 00No 5Connects to U2C1 pin 22D +3.3 CLK+3.3 CLKOFF- 1.25 hz ON - Activity6Connects to U2C1 pin 21CNoNote:Some images of the pre version 9 360 motherboard show LEDs connected to this Port.J7F1CPU SPI EEPROM Header1SCK4/WP2SO5/CS3SI6GNDNote:Header and eeprom is present on 360's XDK (Version 9)Eeprom is missing on some Version 11 motherboards.Connects to the SPI serial eeprom (AT25020) then it probably connects to the Misc I/O bus on the CPU.J3G1Front Memory Card A & B ConnectorA B6GND1GND7+3.3 VDC2+3.3 VDC8USB Data -3USB Data -9USB Data +4USB Data +10GND5GNDNote:USB is 3.3 VDC, Same as RF Module.J6G1RF Module Connector1+3.3 VDC5See Note2USB Data -6Serial Data3USB Data +7Serial CLK4GND8GND9See Note Note:USB is 3.3 VDC, same as memory card portPin 5 Power ON/OFF (momentary tied to gnd to power ON/OFF)Pin 5 goes to southbridge 21EPin 9 goes to Pin 16 of J1A1 (extra pin on the back USB port) but is not connected to anything on the RF Module.J7G1Aux Power Header1GND2+12 VDC13GND Note:1) This port is not active. A resistor or jumper needs to be added to the bottomside of the motherboard were R7V7 should be.Header missing on 360 XDK motherboard Version 9.Header missing on 360 Retail motherboard Version 11.J7G2VID Port1VCC8VID12VID49PWM13FBRTN10VID04VID311PWM25PWRGD12VID56VID213PWM37EN14GNDNote:Pure SpeculationThe Voltage Identification (VID) port was present on early version(s) of the 360 motherboard. (pre Version 9)I have speculated what the connections were.To learn more download the datasheet for the ADP3188. (Analog Devices)J9G1Front Dual USB PortBottom Port Top Port1+5 VDC5+5 VDC 2USB Data -6USB Data -3USB Data +7USB Data + 4GND8GNDAppendix Document VersionVersion 1.0Dec 15, 2005Just PinoutsVersion 1.1Dec 30, 2005Added Photos & Diagrams Version 1.2Jan 6, 2006Changed FormatVersion 1.3 Feb 2, 2006Added SchematicsPrivate ReleaseVersion 1.4 Feb 15, 2006Corrected SchematicsAdded AppendixAdded Block DiagramCurrent DocumentUnique Per Console NumbersL = Production line in the factoryNNNNNN = Xbox in the weekY = Year (last digit)WW = week of the year *FF = Factory # (05 & 06 are China, 05 appears to supply Europe and 06 supplies North America)MM = MonthX = unknown at this time" " = Actual Text* Factory 05 is a week ahead of factory 06 for the 2005 year. This means any 360 made during the last week of December 2005 should have a WW=53 in the serial #.Serial Number = LNNNNNNYWWFF (Source: )Product ID = XXXXXXXXLNNNNNNYWWFFMotherboard = XXXXXXXXXXXXYWWXConsole ID = XXXXXXXXXXXXWired MAC = Unique 12 digit (hex, meaning each digit has the possibility of being a value of 0-F)RF Module = XXXXXXXXXXXYWWDVD Serial # (Hitachi-LG) = YMM"HG"XXXXXXDVD Serial # (Toshiba- Samsung) = X"RCY"XXXXXXRetail Motherboard Differences Motherboard Version 011CPU SPI eeprom: Present or AbsentCPU: Engraved "Canada" or "Taiwan"Tilt Switch: Surface Mount or Thru Hole MountBios Label: Present or Absent10/100 base-TX Ethernet Transceiver: "Big" or "Small"Header Holes: Filled in with solder, partially filled or not filled.Bios/Kernel Versions and Updates Displayed in the dashboard.D: = DashboardK: = KernelBK: = (Backup Kernel, Bios Kernel, Base Kernel, etc) - Not sure2.0.0198.0First image of a XDK Launcher Screen. Show version in the right hand corner.I'm guessing it's an Alpha. (Source Image: I forget)2.0.1232.0 Alpha 2Image of a XDK Launcher Screen. Alpha 2 is displayed beside version #.(Source Image: I forget)2.0.1839.2XeDK release Dashboard. (smartxx images)2.0.1888.0Sept-Oct Production Line for Retail Release2.0.2241.0Late Oct-Early Nov Production Line, Nov 22 available over xbox live.* Unknown2.0.2255.0Jan 30 production line, Jan 30 available over xbox live* Improved logic around deciding if saved games should be deleted and offer the option to only delete the profile and to leave all save data.* Users reporting blank Friends List on the Xbox 360 dash after muting a friend while playing a game in Backwards Compatibility mode.* Improved synching of games played to Web and in console.* Network settings: keyboard does now allow entry of - (dash) character in the keyboard.* Improvements to the Xbox Guide.* Increased accuracy of "last time played."* Network configuration improvements for Xbox Live members in the Netherlands.* More detailed messaging for unreadable disk or region errors.* Blocked the Kiosk Disc from being recognized when inserted into the DVD tray.(Source: I forget, so let me know so I can provide proper credit)System RequirementsAbsolute MinimumMotherboard, Power Supply (12 volt 16amp, 5 volt 1amp), Video Cable, and a momentary pushbutton switch (for power on/off).I have tested this with dashboard 1888 and 2241. A dashboard update could change this.Absolute Minimum to play games or DVDsAs above, but subtract the push button and add the DVD player and a wired controller.Absolute Minimum to play just DVDsAs above, but the remote can be used instead of the wire controller.Remember that this could change with a dashboard update.RetailNote:Flash Bios Version 2.0.1888.0Note:Appears to be a final version of the XeDK.Flash Bios Version 2.0.1839.2Also known as XDK.Used in conjunction with the SDK (Software Development Kit).Most likely, the XeDK is also connected to a network with various PCs running SDK.Source: Note:No DVD connected. Source: Memory Map Not in this Public ReleaseNot in this Public ReleaseNot in this Public ReleaseSouthbridge Pinout Not in this Public ReleaseLeft Blank。
XH规格书
Test condition
Insert and withdraw connectors at the speed rate of 25±3mm/minute 公母对插插拔 30 次，机器行走速度 25±3mm/分钟。
Fix the crimped terminal, apply axial pull out force on the wire at the speed rate of 25±3mm/minute(Based upon JIS C5402 6.8) 端子固定住，将端子从线材拔出， 机器行走速度 25±3mm/分钟。
温度 40±2℃，湿度 90~95%，时间 96 小时。 strength
No Damage
40m∩ MAX
没有损坏/没 有电弧产生
3
3-3-8
3-3-9 3-3-10 3-3-11
津达电子有限公司
Temperatur e cycling 温度冲击 测试
Salt spray 盐水测试
Solderability 沾锡性测试
Appearance No Damage
Contact
40m∩
Resistance MAX
12 hours exposure to a salt spray from the 5±1% solution at 35±2℃.(Based Appearance No Damage
upon JIS
C5402/MIL-STD-202method
101D conditions. B)
Contact
时间 12 小时，盐水体比例 5±1%，温度 Resistance
35±2℃。
40m∩ MAX
Soldering time:3±0.5sec, solder temperature:230±5℃ 时间：3±0.5 秒，
JST-XH图纸中文版
ൟো
BH2B-XH-2 BH3B-XH-2 BH4B-XH-2 BH5B-XH-2 BH6B-XH-2 BH7B-XH-2 BH8B-XH-2 BH9B-XH-2 BH10B-XH-2
XH CONNECTOR ᰳᐿۋ
PP䯈䎱ˋॄࠋ⬉䏃ᵓ⫼䖲఼ˋय़ⴔǃᦦൟ
1
PLQ f
˄˅
5 JST
该产品是封装高度为 17.0mm、厚度为 5.8mm 的高背型 XH 连接器。即使是微小电压、电流的电路，也能充分发挥稳 定的接触性。 ●封装式带座插头 ●兼容性
ሎᇌ˄PP˅
$
%
2.5
7.4
5.0
9.9
7.5
12.4
10.0
14.9
12.5
17.4
15.0
19.9
17.5
22.4
20.0
24.9
22.5
27.4
ᴤ䋼ǃ㸼䴶໘⧚
ᦦ༈˖䪰ড়䞥ǃ䪰ᑩ䬔䫵˄ಲ⌕⛞໘⧚˅ ᑩᑻ˖⦏⩗㑸㓈ᔎሐ啭ǃ8/9ˈ✊㡆˄䈵⠭㡆˅ ●符合 RoHS 标准的产品 本产品的标签上标有（LF）（SN）。
■登录标准
:Recognized E 60389 :Certified LR 20812
■一般规格
●额定电流 ：3A AC/DC（使用 AWG#22 时）
●额定电压 ：250V AC/DC
●使用温度范围 ：-25℃～ +85℃（含通电时的温度上升值）
●接触电阻 ：初
期 /10mΩ 以下
环境试验后 /20mΩ 以下
ሎᇌ˄PP˅
$
%
&
背面通讯接线详细设计图
