各种船型英文缩写(一)
船舶常用英语(一)
motor ship内燃机船
diesel ship柴油机船
electrically-propelled ship电力推进船
steam turbine ship汽轮机船
gas turbine ship燃气轮机船
nuclear-power ship核动力船
deck ship甲板船
inland waterway vessel内河船
civil ship; merchant ship民用船；商船
transport ship运输船
pleasure yacht游艇
passenger ship客船
coasting passenger and cargo ship沿海客货船
passenger and auto-car carrier旅客及汽车运输船
RO/RO barge滚装驳船
liquefied gas barge液化气体驳
hopper barge开底泥驳
split hopper barge对开泥驳
pusher; pushboat顶推船；推船
working ship工程船
tug; tugboat; towboat拖船
harbor tug港作拖船
bilge strake(plate)舭列板
bilge well污水井
bitt系缆桩
bollard系缆桩；系船柱；双系柱
bolster枕垫
bonnet烟囱帽；机罩
boom杆；吊杆；桁；叉架
boom crutch(support; rest)吊杆支架
bossing尾管突出部；轴包套
bottom frame船底横骨
vehicle-passenger ferry catamaran双体车客渡船
船舶英文缩写
HULL(船体):ABS (American Bureau of Standard)美国船级社ANG (Angle Bar)角钢BFE (Builder Furnish Equipment)建造商提供设备BG (Bulk Carrier)散货船BHD (Bulkhead)舱壁BHP (Break Horsepower)制动马力BL (Base Line)基线BM (Breadth Molded)型宽BV (Bureau Veritas)法国船级社CAD (Computer Aided Design)计算机辅助设计CAM (Computer Aided Manufacturing)计算机辅助制造CB (Center of Buoyancy)浮心CCS (China Classification Society)中国船级社CF (Center of Floatation)漂心CFE (Contractor Furnish Equipment)承包商提供设备CG (Center of Gravity)重心CH (Channel)槽钢CM (Metacenter)稳心CPP (The Controllable Pitch Propeller)可调螺距桨CS (Carbon Steel)碳素钢DB (Double Bottom)双层底DK (Deck)甲板DM (Depth Molded)型深DNV (Det Norske Veritas)挪威船级社DWG (Drawing)图DWL (Design Waterline)设计水线DWT (Deadweight)载重量FAT (Factory Acceptance Test)工厂验收试验FB (Flat Bar)扁钢FEM (Finite Element Method)有限元法FPSO (Floating Production Storage Offloading) 浮（船）式生产储油卸油系统FSO (Floating Storage Offloading)浮（船）式储油卸油系统Fwd (Forward)向船艏GL (Germanischer Lloyd)德国船级社GM (Metacentric Height)初稳心高HP (Half Bulb Plate)球扁钢LBP (Length between Perpendiculars)垂线间长LCG (Longitudinal Center of Gravity)纵向重心LNG (Liquefied Natural Gas Vessel) 液化石油气船LOA (Overall Length)总长Long. (Longitudinal)纵骨LPG (Liquefied Petroleum Gas Vessel) 液化天然气船LR (Lloyd's Register)英国劳氏船级社MDK (Main Deck)主甲板MODU (Mobile Offshore Drilling Units)移动式近海钻井平台MS (Mild Steel)低碳钢MTO (Material Takeoff)材料估算NK (Nippon Kaiji Kyokai)日本海事协会OFE (Owner Furnished Equipment)船东提供设备OT (Oil Tight)油密PL (Plate)板RI (Register Italian)意大利船级社SB (Starboard)右舷Semi- (Semi-submersible Platform)半潜式钻井平台STLP (Suspended Tension Leg Platform)悬式张力腿平台TCG (Transverse Center of Gravity)横向重心TEU (Twenty-foot equivalent Unit)20英尺国际标准集装箱TLP (Tension Leg Platform)张力腿平台UCLL (Ultra Large Crude Carrier)超大型油船VCG (Vertical Center of Gravity)垂向重心VLCC (Very Large Crude Carrier)特大型油船WB (Web Bar)腹板WL (Waterline)水线WT (Water Tight)水密MECHANICAL & PIPING（轮机）：AHU (Air Handling Unit)通风装置BHP (Break Horsepower)制动马力A/C (Air Compressor)空气压缩机A/C (Air Conditioning)空调BB (Ball Bearing)滚珠轴承BRG (Bearing)轴承CAS NUT(Castle Nut)蝶型螺帽CCR (Central Control Room)中心控制室COW (Crude Oil Washing)原油洗舱DFO (Diesel Fuel Oil)柴油DPS (Dynamic Position System)动力定位系统DT (Double-Thread)双头螺纹FS (Forged Steel)锻钢FW (Fresh Water)淡水FO (Fuel Oil)燃油GRP (Glass-reinforced Plastic)玻璃钢HVAV (Heating Ventilation and Air-condition)暖通空调系统HPU (Hydraulic Power Unit)液压工作站LSA (Life Saving Apparatus)救生器具LCC (Local Control Console)机旁控制台LO (Lube Oil)滑油MDO (Marine Diesel Oil)船用柴油OS (Operation System)操作系统PLC (Programmable Logic Controller)逻辑控制单元PMS (Power Manage System)动力管理系统ELECTRICAL（电气）:AC (Alternative Current)交流电AVR (Automatic Voltage Regulation)自动电压调整计CCTV (Closed Circuit Television)闭路电视CMS (Cargo Monitoring System)货物监控系统DC (Direct Current)直流电DFT (Dry Film Thickness)干膜DG (Diesel Generator)柴油发电机DVD (Digital Video Disc) 数字化视频光盘EMSP (Emergency Shutter Panel)应急关断板ESS (Emergence Shutdown System)应急关闭系统GPS (Global Position System)全球定位系统HG (Harbor Generator)停泊发电机HT (High Temperature)高温JB (Junction Box)接线盒LED (Light Emitting Diode)发光二极管LT (Low Temperature)低温MCU (Main Control Unit)主控器箱MG (Main Generator)主发电机MUR (Manual Voltage Regulation)手动调压器NEMA (National Electrical Manufacturers Association) 国际电气制造业协会PA (Public Address System)公共寻呼系统PWM (Pulse Width Modulation)脉宽调制ST (Starter)启动器SWBD (Switch Board)配电盘，配电板UPS (Uninterrupted Power Supply)不间断电源VCR (Video Cassette Recorder)录像机PAINTING（涂装）:ARD (Alkyd Resin Deck)醇酸树脂甲板漆ARF (Alkyd Resin Finish)醇酸树脂面漆ARP (Alkyd Resin Primer)醇酸树脂底漆A/C (Anti-corrosive Paint)防腐漆CAF (Compressed Asbestos Fiber)压缩石棉填料EDP (Epoxy Deck Paint)环氧甲板漆EFP (Epoxy Finish Paint)环氧面漆EPP (Epoxy Primer Paint)环氧底漆ETPF (Epoxy Tank Paint Finish)环氧舱室面漆ETPP (Epoxy Tank Paint Primer)环氧舱室底漆ETP (Epoxy Topside Paint)环氧干舷漆ERL (Erosion Resistant Lacquer)防腐漆ECP (Etching Primer) 磷化底漆EPR (Ethylene-Propylene Rubber)乙丙橡胶F/C (Finish Coating)面漆IZP (Inorganic Zinc Primer)无机锌底漆IZSP (Inorganic Zinc Shop Primer)无机锌车间底漆UTP (Polyurethane Topside Primer)聚氨脂干舷漆TE (Tar Epoxy Paint)环氧焦油漆VTP (Vinyl Tar Primer)聚乙烯焦油底漆ZRP (Zinc Rich Primer)富锌底漆WELDING and Material（焊接与材料）:ASTM (American Society for Testing Materials)美国材料实验协会AWS (American Welding Society)美国焊接协会FCAW (Flux Cored Arc Welding)药芯焊丝电弧焊FRP (Fiberglass Reinforced Polyester)玻璃钢GMAW (Gas Metal Arc Welding)气体保护金属极电弧焊GRP (Glass Reinforced Polyester)玻璃钢GTAW (Gas Tungsten Arc Welding)气体保护钨极电弧焊GW (Gravity Welding)重力焊MPI (Magnetic Particle Inspection) 磁粒检验NDE (Nondestructive Evaluation)无损鉴定NDT (Nondestructive Testing)非破坏性检验PVC (Poly Vinyl Chloride)聚氯乙烯S/W (Spot Weld) 点焊SAW (Submerge Arc Welding)埋弧焊SMAW (Shielded Metal Arc Welding)手弧焊UT (Ultrasonic Test)超声波检验WPS (Welding Procedure Sheet)焊接程序表WQT (Welding Qualification Test)焊工资格检验OTHERS（其它）:AE (Assistant Engineer)助理工程师ANSI (American National Standards Institute)美国国家标准局API (American Petroleum Institute)美国石油协会ASME (American Society of Mechanical Engineers)美国机械工程师协会Bbls (Barrels) 桶（美制容量单位 1桶 = 159升），C.E. (Chief Engineer) 总工程师CEO (Chief Executive Officer)首席执行总裁CIS (Chinese Industrial Standard)中国工业标准CNOOC (China National Offshore Oil Company)中国海洋石油总公司Co Ltd.(Company Limited)（股份）有限公司cu.ft. (Cubic Feet) 立方英尺cu.in. (Cubic Inch) 立方英寸GB (Guo Biao)国标GM (General Manage)总经理H.Q. (Headquarters) 总部HSE (Health, Safety & Environment)健康，安全和环保ID (Inner Dimension)内径IEC (International Electro technical Commission)国际电工协会IMO (Intergovernmental Marine Organization)国际海事组织ISO (International Standardization Organization)国际标准化协会ITU (International Telecommunication Union)国际电信联盟Ksi (kilopounds per square inch)千磅/平方英寸N/A (None Applicable)不适用NACE (National Association of Corrosion Engineer)全国防蚀工程师协会NFPA (National Fire Protection Association)国家防火协会OD (outer Dimension)外径QA (Quality Assurance)质量保证QC (Quality Control)质量管理（检查）ST (Short Ton)短吨SOLAS (International Convention of the Safety of Life at Sea)国际海上人命安全公约Spec. (specification)说明书，规格书sq.ft. (Square Feet) 平方英尺sq.in. (Square Inch) 平方英寸PROPER NOUN（专有名词）:Basic Design(基础设计): Preparation of specification and plans/drawings outlining the design and in sufficient detail to gain Class approval. 总括性的设计规格书和图纸等，其详细程度仅足可以通过船级社认可其设计思想。
船舶简称
船舶简称各种船型英文缩写（一）按照字母首位顺序排列：Carrier (散货船)其类型分类有：- Handysize (灵便型) ：2~5万吨左右，大灵便型：大于4万吨- Panamax（巴拿马型）: 6~万吨，船的总长小于或等于，型宽小于或等于；目前平均载重吨达到万吨- Kmsarmax（卡尔萨姆型）:8~万吨- Capesize（好望角型）:15万吨左右（集装箱）（货舱区分：中央部位货舱——集装箱船；其他舱位——普通杂货船可变换区分：货舱内结构可拆装——集装箱船；不可拆装——普通杂货船）Tanker（油轮）其类型分类有：- ULCC(巨型原油轮):大于30万吨- VLCC(超大原油轮)：20~30万吨- Suezmax(苏伊士型)：12~16万吨- Aframax(阿芙拉型)：8~12万吨- Panamax(巴拿马型)：6~8万吨各种船型英文缩写（二）按照字母首位顺序排列：BBC:Bulk Carrier 散货船CCOT:Cargo Oil Tanker 货油轮DDFF: 高速渡轮EERRV: 救援船FFLNG: 浮式液化天然气船（科代替岸上传统的液化天然气工厂）FPSO: 浮式生产储油船FPV: 浮式生产设备GG-Cargo Ship: 杂货船LLNG: 液化天然气船LEG: 液化乙烯汽船LPG: 全压式液化石油汽船LSV: 驳运支援船LR成品油轮:stands for large range, 远程成品油轮MMR成品油轮:stands for medium range, 中程成品油轮OOSV:Offshore Support Vessel, 海洋工程船PPSV: 平台供应船PC: 重型石油化学制品运输船PCC:Pure Car Carrier 汽车运输船PCTC:Pure Car & Truck Carrier 大型轿车卡车专用船RRO-RO SHIP: 客滚船Roll-on/Roll-off ship: 滚装船UUCLL: Ultra Large Crude Carrier: 超大型原油轮VVLOC: 大型矿砂船VLCC: 巨型原油轮1、DWTDWT 是DEAD WEIGHT TONNAGE 的缩写，是表示“载重吨”。
船舶简称
船舶简称各种船型英文缩写（一）按照字母首位顺序排列：1.Bulk Carrier (散货船)其类型分类有：- Handysize (灵便型) ：2~5万吨左右，大灵便型：大于4万吨- Panamax（巴拿马型）: 6~7.5万吨，船的总长小于或等于274.32M，型宽小于或等于32.30M；目前平均载重吨达到8.2万吨- Kmsarmax（卡尔萨姆型）:8~8.9999万吨- Capesize（好望角型）:15万吨左右2.Container（集装箱）（货舱区分：中央部位货舱——集装箱船；其他舱位——普通杂货船可变换区分：货舱内结构可拆装——集装箱船；不可拆装——普通杂货船）3.Oil Tanker（油轮）其类型分类有：- ULCC(巨型原油轮):大于30万吨- VLCC(超大原油轮)：20~30万吨- Suezmax(苏伊士型)：12~16万吨- Aframax(阿芙拉型)：8~12万吨- Panamax(巴拿马型)：6~8万吨各种船型英文缩写（二）按照字母首位顺序排列：BBC:Bulk Carrier 散货船CCOT:Cargo Oil Tanker 货油轮DDFF: 高速渡轮EERRV: 救援船FFLNG: 浮式液化天然气船（科代替岸上传统的液化天然气工厂）FPSO: 浮式生产储油船FPV: 浮式生产设备GG-Cargo Ship: 杂货船LLNG: 液化天然气船LEG: 液化乙烯汽船LPG: 全压式液化石油汽船LSV: 驳运支援船LR成品油轮:stands for large range, 远程成品油轮MMR成品油轮:stands for medium range, 中程成品油轮OOSV:Offshore Support Vessel, 海洋工程船PPSV: 平台供应船PC: 重型石油化学制品运输船PCC:Pure Car Carrier 汽车运输船PCTC:Pure Car & Truck Carrier 大型轿车卡车专用船RRO-RO SHIP: 客滚船Roll-on/Roll-off ship: 滚装船UUCLL: Ultra Large Crude Carrier: 超大型原油轮VVLOC: 大型矿砂船VLCC: 巨型原油轮1、DWTDWT 是DEAD WEIGHT TONNAGE 的缩写，是表示“载重吨”。
各种船型英文缩写
各种船型英文缩写各种船型英文缩写（一）Bulk Carrier (散货船)- Handysize (灵便型) ：2~5万吨左右，大灵便型：大于4万吨- Panamax（巴拿马型）: 6~7.5万吨，船的总长小于或等于274.32M，型宽小于或等于32.30M；目前平均载重吨达到8.2万吨- Kmsarmax（卡尔萨姆型）:8~8.9999万吨- Capesize（好望角型）:15万吨左右Container（集装箱）（货舱区分：中央部位货舱——集装箱船；其他舱位——普通杂货船可变换区分：货舱内结构可拆装——集装箱船；不可拆装——普通杂货船）Oil Tanker（油轮）- ULCC(巨型原油轮):大于30万吨- VLCC(超大原油轮)：20~30万吨- Suezmax(苏伊士型)：12~16万吨- Aframax(阿芙拉型)：8~12万吨- Panamax(巴拿马型)：6~8万吨各种船型英文缩写（二）按照字母首位顺序排列：BBC:Bulk Carrier 散货船CCOT:Cargo Oil Tanker 货油轮DDFF: 高速渡轮EERRV:救援船FFLNG: 浮式液化天然气船（科代替岸上传统的液化天然气工厂）FPSO: 浮式生产储油船FPV: 浮式生产设备GG-Cargo Ship: 杂货船LLNG: 液化天然气船LEG: 液化乙烯汽船LPG: 全压式液化石油汽船LSV: 驳运支援船LR 成品油轮:stands for large range, 远程成品油轮MMR成品油轮:stands for medium range, 中程成品油轮OOSV:Offshore Support Vessel, 海洋工程船PPSV: 平台供应船PC: 重型石油化学制品运输船PCC:Pure Car Carrier 汽车运输船PCTC:Pure Car & Truck Carrier 大型轿车卡车专用船RRO-RO SHIP: 客滚船Roll-on/Roll-off ship: 滚装船UUCLL: Ultra Large Crude Carrier: 超大型原油轮VVLOC: 大型矿砂船VLCC: 巨型原油轮VLGC: 大型液化气体运输船。
船舶英语及船型简称和缩写
船舶英语及船型简称和缩写船舶英语船舶英语和基本词汇改编加整合目录一、造船部分------------------------------------------------------------------31、船体部分--------------------------------------------------------------------32、机舱部分-------------------------------------------------------------------93、电气部分-------------------------------------------------------------------134、船装部分-------------------------------------------------------------------23二、造机部分-----------------------------------------------------------------29三、修造部分-----------------------------------------------------------------31一、造船部分1、HULL PART 船体部分1、1结构S t r u c t u r e12船厂 d o c k y a r d/s h i p y a r d船坞 d o c k/b o a t y a r d 船东 s h i p-o w n e r船舷 S h i p's s i d e船码头 q u a y/d o c k船的栏杆 S h i p's r a i l船舱 h o l d甲板 D e c k船籍 S h i p's r e g i s t r y住舱甲板 a c c o m m o d a t i o n d e c k 船首 b o w梁拱甲板 a r c h d e c k船梯 l a d d e r载货甲板 c a r g o d e c k船尾 s t e r n首楼甲板 F o r e c a s t l e d e c k上甲板 U p p e r d e c k下甲板 L o w e r d e c k主甲板 M a i n d e c k货舱甲板 H o l d d e c k桥楼甲板 B r i d g e d e c k水密甲板 W a t e r t i g h t d e c k34驾驶甲板 N a v i g a t i o n d e c k铜-钢复合板 C o p p e r s h e a t h i n gs t e e l p l a t e艇甲板 B o a t d e c k甲板边板 D e c k s t r i n g e r p l a t e 罗经甲板 C o m p a s s d e c k斜板 S l o p i n g p l a t e板 P l a t e加强板 R e i n f o r c e m e n t p l a t e 舭板 B i l g e p l a t e舵板 R u d d e r p l a t e船底板 B o t t o m p l a t e舷侧外板 S i d e p l a t e船外板 S h e l l p l a t e裙板 S k i r t p l a t e船首外板 B o w p l a t e首柱板 S t e m p l a t e肘板 B r a c k e t p l a t e首柱板 S t e r n p l a t e舱壁板 B u l k h e a d p l a t e平台 p l a t f o r m槽形舱壁板 C o r r u g a t e d b u l k h e a d p l a t e机舱平台E n g i n e-r o o m p l a t f o r m 舷墙板 B u l w a r k p l a t e分段B l o c k围板 C o a m i n g p l a t e首段 B o w b l o c k连续板 C o n n e c t i o n p l a t e中段 M i d s h i p b l o c k56尾段 S t e r n b l o c k甲板下纵桁 U n d e r d e c k g i r d e r 左舷 p o r t舭纵桁 W i n g g i r d e r右舷 S t a r b o a r d支柱 P i l l a r纵桁 G i r d e r肋骨 F r a m e型材桁 B a r g i r d e r基础台架 B a s e f r a m e中底桁 B o t t o m c e n t e r g i r d e r支架 B e a r f r a m e中内龙骨 B o t t o m c e n t e r l i n e g i r d e r舭肋骨 B i l g e f r a m e底桁材 B o t t o m g i r d e r船底肋骨 B o t t o m f r a m e旁桁材 B o t t o m s i d e g i r d e r首肋骨 B o w f r a m e甲板纵桁 D e c k g i r d e r肘板框架肋骨 B r a c k e t f r a m e 横桁 C r o s s g i r d e r球鼻首肋骨 B u l b o u s b o w f r a m e水平桁 H o r i z o n t a l g i r d e r球曲型肋骨 B u l b o u s f r a m e舱口边梁 H a t c h c o a m i n g g i r d e r主肋骨 C h i e f f r a m e机座纵桁 E n g i n e g i r d e r首肋骨 F o r e f r a m e7桁架梁 G i r d e r f r a m e舭纵桁舭纵骨 B i l g e l o n g i t u d i n a l 舯部肋骨 M i d d l e f r a m e船底纵骨/纵桁 b o t t o m l o n g i t u d i n a l 尖舱肋骨 P e a k f r a m e船底腹板纵桁 b o t t o m w e bl o n g i t u d i n a l加强筋 S t i f f e n e d f r a m e甲板纵桁 D e c k l o n g i t u d i n a l横框架肋骨 T r a n s v e r s e f r a m e内底纵桁/纵骨 I n n e r b o t t o ml o n g i t u d i n a l肋距 F.S.(f r a m e s p a c e)舷侧纵桁/纵骨 S h e l l s i d el o n g i t u d i n a l纵桁/纵骨/纵向构件 l o n g i t u d i n a l双层底顶纵骨 T o p l o n g i t u d i n a l o fd o u b le b o t t o m89舱 T a n k斜舱壁纵骨 S l o p p i n g-b u l k h e a dl o n g i t u d i n a l结构 s t r u c t u r e尾尖舱 a f t e r p e a k t a n k附属结构 A c c e s s o r y s t r u c t u r e尾部水舱 a f t e r w a t e r t a n k全焊结构 A l l-w e l d e d s t r u c t u r e辅助水柜 A u x i l i a r y w a t e r t a n k 中部结构 A m i d s h i p s s t r u c t u r e辅助压载水舱 A u x i l i a r y w a t e rb a l l a s t t a n k泊位结构 B e r t h i n g s t r u c t u r e污水舱 B i l g e t a n k 底部龙骨结构 B o t t o m k e e l s t r u c t u r e底舱 B o t t o m t a n k船首部结构 B o w s t r u c t u r e底边舱 B o t t o m s i d e t a n k支撑结构 B r a c e d s t r u c t u r e货油压载舱 C a r g o a n d b a l l a s tt a n k桥楼结构 B r i d g e s t r u c t u r e循环水槽 C i r c u l a t i n g f l o ww a t e r t a n k首楼结构 F o r e c a s t l e s t r u c t u r e循环滑油舱 C i r c u l a t i n gl u b r i c a t i n g o i l t a n k 构架结构 F r a m e d s t r u c t u r e清洁压载舱 C l e a n b a l l a s t t a n k 纵桁结构 G i r d e r s t r u c t u r e冷凝水柜 C o n d e n s a t e c a t c h t a n k 人孔 m a n h o l e干舱 D r y t a n k1011饮用水舱 D r i n k i n g w a t e r t a n k密封圈 S e a l i n g r i n g污水舱 B i l g e t a n k铰链 H i n g e应急淡水柜 E m e r g e n c y f r e s h w a t e r t a n k 把手 H a n d l e首舱 F o r e t a n k平衡块 B a l a n c e b l o c k首尖舱 F o r e p e a k t a n k斜边舱 H o p p e r s i d e t a n k1、2w e l d i n g焊接液舱 L i q u i d t a n k坡口 g r o o v e龙骨舱 K e e l t a n k单面坡口 S i n g l e g r o o v e右舷舱 S t a r b o a r d t a n k双面坡口 D o u b l e g r o o v e 顶边水舱T o p s i d e t a n kⅠ形坡口 S q u a r e g r o o v e顶边翼舱 T o p s i d e w i n g t a n k V型坡口 S i n g l e v g r o o v e小舱口盖 S m a l l h a t c h c o v e r U型坡口 S i n g l e u g r o o v eX形坡口 S i n g l e v g r o o v e水密舱口盖 W a t e r-t i g h t s m a l l h a t c hc o v e rK形坡口 S i n g l e b e v e l g r o o v e 风雨密舱口盖 W e a t h e r-t i g h t s m a l l h a t c hc o v e r1213Y形坡口 S i n g l e v g r o o v e w i t h b r o a d填充金属 F i l l e r m e t a lr o o d f a c e坡口面 G r o o v e f a c e热影响区 H e a t-a f f e c t e dz o n e(H A Z)坡口角度 G r o o v e a n g l e过热区 O v e r h e a t e d z o n e焊缝倾角 W e l d s l o p e焊合线 B o n d l i n e(f u s i o nl i n e)接头根部 R o o t o f j o i n t焊接区 W e l d z o n e根部间隙 R o o t g a p焊缝区 W e l d m e t a l a r e a钝边 R o o t f a c e焊缝 w e l d焊接接头 W e l d i n g j o i n t连续焊缝 C o n t i n u o u s w e l d对接接头 B u t t j o i n t断续焊缝 I n t e r m i t t e n t w e l d 角接接头 C o r n e r j o i n t纵向焊缝 L o n g i t u d i n a l w e l dT形接头 T-j o i n t横向焊缝 T r a n s v e r s e w e l d搭接接头 L a p j o i n t对接焊缝隙 B u t t w e l d十字接头 C r o s s s h a p e d j o i n t角焊缝 F i l l e d w e l d 母材 B a s e m e t a l(p a r e n t m e t a l)并列断续角焊缝 C h a i n i n t e r m i t t e n tf i l l e t1415交错断续角焊缝 S t a g g e r e d i n t e r m i t t e n tf i l l e t弧焊整流器 A r c w e l d i n g r e c t i f i e r 焊缝正面 F a c e o f w e l d自动焊 A u t o m a t i c w e l d i n g焊缝背面 B a c k o f w e l d埋弧自动焊 S u b m e r g e d a r c w e l d i n g 焊缝宽度 W e l d w i d t h半自动焊 S e m i-a u t o m a t i cw e l d i n g焊缝长度 W e l d l e n g t h氩弧焊 A r g o n-a r c w e l d i n g 焊缝余高 R e i n f o r c e m e n t二氧化碳气体保护焊 C O2g a s s h i e l d e d a r c w e l d i n g焊脚 L e g(o f a f i l l e t w e l d)氧乙炔焊 O x y-a c e t y l e n e w e l d i n g焊脚长度 L e g l e n g t h气割 G a s c u t t i n g套管接头 M u f f j o i n t碳弧气刨 C a r b o n a r c a i rg o u g i n g手工电弧焊 M a n u a l a r c w e l d i n g(s h i e l d e dm e t a l a r c w e l d i n g)水下切割 U n d e r w a t e r c u t t i n g 直流电弧焊 D i r e c t c u r r e n t a r c w e l d i n g 等离子弧切割 P l a s m a a r c c u t t i n g 交流电弧焊 a l t e r n a t i n g c u r r e n t a r cw e l d i n g连续焊 C o n t i n u o u s w e l d i n g 弧焊变压器 A r c w e l d i n g t r a n s f o r m e r断续焊 I n t e r m i t t e n t w e l d i n g点焊 S p o r t w e l d i n g1617对接焊 B u t t w e l d i n g分段退焊 B a c k s t e p w e l d i n g 角焊 F i l l e t w e l d i n g分段多层焊 B l o c k w e l d i n g搭接焊 L a p w e l d i n g深溶焊 D e e p p e n e t r a t i n gw e l d i n g返修焊 R e-w e l d i n g跳焊 S k i p w e l d i n g补焊 R e p a i r w e l d i n g陶质衬垫焊 C e r a m i c b a c k i n gw e l d i n g定位焊 T a c k w e l d i n g引弧 S t r i k i n g t h e a r c封底焊 B a c k s e a l i n g w e l d i n g焊接工艺参数 W e l d i n g c o n d i t i o n打底焊 B a c k i n g w e l d i n g焊接电流 W e l d i n g c u r r e n t堆焊 S u r f a c i n g(o v e r l a y i n g)焊接电压 W e l d i n g v o l t a g e塞焊 P l u g w e l d i n g焊接速度 W e l d i n g s p e e d槽焊 S l o t w e l d i n g电弧电压 A r c v o l t a g e盖面焊 C o n s m e t i c w e l d i n g焊丝间距 W i r e s p a c i n g前倾焊 F o r w a r d w e l d i n g空载电压 O p e n c i r c u i t v o l t a g e 后倾焊 B a c k w a r d w e l d i n g熔化速度 M e l t i n g r a t e1819送丝速度 W i r e f e e d r a t e层间温度 I n t e r-p a s st e m p e r a t u r e气体流量 G a s f l o w r a t e焊后热处理 P o s t-w e l d h e a t t r e a t m e n t焊丝伸出长度 W i r e e x t e n s i o n锤击 P e e n i n g极性 P o l a r i t y全焊透 F u l l p e n e t r a t i o nw e l d i n g正极/阳极 P o s i t i v e e l e c t r o d e熔池 W e l d-p o o l负极/阴极 N a v i g a t e e l e c t r o d e熔深 P e n e t r a t i o n左焊法 L e f t w a r d w e l d i n g弧长 A r c l e n g t h右焊法 R i g h t w a r d w e l d i n g喷射过渡 S p r a y t r a n s f e r电流密度 C u r r e n t d e n s i t y短路过渡 S h o r t c i r c u i t i n gt r a n s f e r线能量 H e a t i n p u t熔滴过渡 M e t a l t r a n s f e r预热 P r e h e a t焊缝成形 A p p e a r a n c e o f w e l d 后热 P o s t-h e a t焊缝成形系数 F o r m f a c t o r o f w e l d 预热温度 P r e h e a t t e m p e r a t u r e熔敷系数 D e p o s i t i o nc o e f f c i e n t后热温度 P o s t-h e a t t e m p e r a t u r e熔敷效率 D e p o s i t i o ne f f i c i e n c y2021熔合比 P e n e t r a t i o n r a t i o立焊 V e r t i c a l p o s i t i o nw e l d i n g等速送丝 C o n s t a n t w i r e-f e e d s y s t e m仰焊 O v e r h e a d p o s i t i o nw e l d i n g变速送丝 a l t e r n a t e w i r e-f e e d s y s t e m 立向上焊 V e r t i c a l u p w e l d i n g 电弧静特性 S t a t i c c h a r a c t e r i s t i c o f立向下焊 V e r t i c a l d o w n w e l d i n ga r c电弧动特性 d y n a m i c c h a r a c t e r i s t i c o f单面焊 W e l d i n g b y o n e s i d ea r c焊接性试验 W e l d a b i l i t y t e s t双面焊 W e l d i n g b y b o t h s i d e 焊接结构 W e l d e d c o n s t r u c t i o n单道焊 S i n g l e-p a s s w e l d i n g 焊道 B e a d多道焊 M u l t i-p a s s w e l d i n g 焊层 L a y e r多层焊 M u l t i-l a y e r w e l d i n g正接（正极性） S t r a i g h t p o l a r i t y焊接材料 C o n s u m a b l e s反接（反极性） R e v e r s e d p o l a r i t y焊条 E l e c t r o d e焊接位置 P o s i t i o n o f w e l d i n g焊条药皮 C o a t i n g 平焊 F l a t p o s i t i o n w e l d i n g酸性焊条 A c i d e l e c t r o d e横焊 H o r i z o n t a l p o s i t i o n w e l d i n g 碱性焊条 B a s i c e l e c t r o d e 2223低氢型焊条 L o w h y d r o g e n t y p e e l e c t r o d e 焊丝盘W i r e r e e l铁粉性焊条 I r o n p o w e r t y p e e l e c t r o d e铜冷却板 C u-c o o l i n g p l a t e重力焊条 G r a v i t y e l e c t r o d e铜滑块 C o p p e r s h o e 焊剂 F l u x切割 C u t t i n g熔炼焊剂 F u s e d f l u x焊接工作台 W e l d i n g b e n c h烧结焊剂 S i n t e r e d f l u x焊接变位机 P o s i t i o n e r焊丝 W i r e送丝机构 W i r e f e e d e r药芯焊剂 F l u x-c o r e d w i r e行走机构 T r a v e l e r保护气体 S h i e l d e d g a s焊接车间 W e l d i n g s h o p焊剂垫 F l u x b a c k i n g引弧板 R u n-o n t a b(e n d t a b)重力焊条 G r a v i t y e l e c t r o d e引出板 R u n-o f f t a b(e n d t a b)焊剂漏斗 F l u x-h o p p e r定位板 S t r o n g-b a c k流量计 F l o w m e t e r焊接衬垫 W e l d i n g b a c k i n g干燥箱 D r y e r敲渣锤 C h i p p i n g h a m m e r 2425面罩 H e l m e t条虫状气孔 W o r m h o l e焊工手套 W e l d i n g g l o v e密集气孔 P o r o s i t y焊钳 E l e c t r o d e h o l d e r针尖状气孔 P i n h o l e焊枪 W e l d i n g g u n白点 F i s h e y e(f l a k e)导电嘴 T i p切口 K e r f喷嘴 N o z z l e咬边 U n d e r c u t焊矩 T o r c h焊瘤 o v e r l a p焊接缺陷 W e l d i n g d e f e c t凹坑 P i t未焊透 I n c o m p l e t e p e n e t r a t i o n烧穿 B u r n t h r o u g h未熔合 I n c o m p l e t e f u s i o n未满焊 I n c o m p l e t e f i l l e dg r o o v e渣 S l a g清根 B a c k c h i p p i n g夹渣 S l a g(s l a g i n c l u s i o n)清渣 S l a g r e m o v a l夹杂物 I n c l u s i o n焊接烟尘 W e l d f u m e气孔 B l o w h o l e电光性眼炎 E y e-f l a s h2627焊接性 W e l d a b i l i t y横裂纹 T r a n s v e r s e c r a c k碳当量 C a r b o n e q u i v a l e n t纵裂纹 L o n g i t u d i n a l c r a c k 未焊满 I n c o m p l e t e f i l l e d g r o o v e焊趾裂纹 T o e c r a c k焊接裂纹 W e l d c r a c k机械性能试验 M e c h a n i c a l p r o p e r t yt e s t热裂纹 H o t c r a c k试板 T e s t p i e c e冷裂纹 C o l d c r a c k试样 S p e c i m e n氢致裂纹 H y d r o g e n–i n d u c e d c r a c k侧弯 S i d e b e n d延迟裂纹 D e l a y e d c r a c k弯曲 B e n d i n g层状撕裂 L e m e l l a r t e a r i n g横向拉伸 T r a n s v e r s e t e n s i l e 弧坑裂纹 C r a t e r c r a c k宏观试样 M a c r o-e t c h i n gs p e c i m e n根部裂纹 R o o t c r a c k微观试样 M i c r o-e x a m i n a t i o ns p e c i m e n再热裂纹 R e h e a t c r a c k破断试验 F r a c t u r e t e s t热影响区裂纹 H e a t-e f f e c t e d z o n e c r a c k抗裂试验 C r a c k i n g t e s t晶间裂纹 I n t e r c y s t a l l i n e c r a c k脆性断裂 B r i t t l e f r a c t u r e 2829塑性断裂 P l a s t i c f r a c t u r e焊接方法 W e l d i n g p r o c e s s焊接残余裂纹 W e l d i n g r e s i d u a l s t r e s s焊接工艺 W e l d i n g t e c h n o l o g y 消除应力 S t r e s s r e l i e v i n g焊接操作 W e l d i n g o p e r a t i o n焊接变形 W e l d i n g d e f o r m a t i o n焊接顺序 W e l d i n g s e q u e n c e角变形 A n g u l a r d i s t o r t i o n焊接方向 D i r e c t i o n o f w e l d i n g 外观检查 V i s u a l e x a m i n a t i o n常用缩语气电立焊 E G W无损探伤 N o n-d e s t r u c t i o nt e s t i n g(N.D.T.)超声波探伤 U l t r a s o n i c i n s p e c t i o n药芯电弧焊 F C A W实心电弧焊 G M A W射线探伤（X光） R a d i o g r a p h i ci n s p e c t i o n(X-r a yi n s p e c t i o n)焊剂铜衬垫单面埋弧自动焊 F C B磁粉探险伤 M a g n e t i c p a r t i c l ei n s p e c t i o n渗透探伤 P e n e t r a t e i n s p e c t i o n手工电弧焊 S M A W 熔池 W e l d-p o o l埋弧自动焊 S A W焊机（焊接电源） W e l d s o u r c e3031钨极惰性气体保护电弧焊 T I G机舱部分 E N G I N E R O O M P A R T 熔化极惰性气体保护焊 M I G一、机舱设备 M a c h i n e s a n de q u i p m e n t i n e n g i n er o o m活性气体保护焊 M A G1、主机 M a i n e n g i n e手工电弧切割 S M A C1）主机油底壳 T h e s u m p t a n k o f M.E.2）主机飞轮 F l y w h e e l o f M.E3）活塞 P i s t o n2、发电机 G e n e r a t o r e n g i n e1）应急发电机 E m e r g e n c y g e n e r a t o re n g i n e2）辅机 A u x i l i a r y3、锅炉 B o i l e r1）组合锅炉 T h e c o m p o s i t e b o i l e r2）锅炉安全阀 T h e s a f e t y v a l v e o fb o i l e r32343）燃烧器 O i l b u r n e r u n i t3）主空气瓶 M a i n a i r r e s e r v o i r 4）水位表 W a t e r l e v e l g a u g e4）应急空气瓶 E m e r g e n c y a i rr e s e r v o i r5）水位控制器 W a t e r l e v e l c o n t r o l l e r5、控制空气瓶C o n t r o l a i r r e s e r v o i r 6）过量蒸气调节阀 E x c e s s s t e a m p r e s s u r ec o n t r o l v a l v e6、空气干燥器 A i r d r y e r4、舵机 7、分油机 O i l p u r i f i e r1）舵机间 S t e e r i n g r o o m1）燃油分油机 F u e l o i l p u r i f i e r 2）舵机装置 S t e e r i n g-g e a r2）柴油分油机 D i e s e l o i l p u r i f i e r 3）手操舵装置 T r i c k w h e e l p l a n t3）滑油分油机 L u b r i c a t e o i lp u r i f i e r4）油缸 O i l c y l i n d e r4）排渣 S l u d g e d i s c h a r g e 5）反馈装置 F e e d b a c k d e v i c e8、制淡装置 F r e s h w a t e r g e n e r a t o r 6）舵 R u d d e r9、焚烧炉 I n c i n e r a t o r 舵叶 R u d d e r b l a d e10、油水分离器 O i l w a t e r s e p a r a t o r 舵杆 R u d d e r s t o c k11、生活污水处理器S e w a g e t r e a t p l a n t上舵承 R u d d e r c a r r i e r12、大气冷凝器 A t m o s p h e r e c o n d e n s e r 3536热水井 C a s c a d e a n d i n s p e c t i o n(h o tw e l l)5）主机燃油供给泵 M a i n e n g i n e f u e l o i ls u p p l y p u m p滑油自清滤器 T h e a u t o m a t i c b a c k-f l a s hl u b r i c a t i n g o i l f i l t e r 6）主机燃油增压泵 M a i n e n g i n e f u e l o i lb o o s t e r p u m p燃油单元 F u e l o i l u n i t7）主机十字头泵 M a i n e n g i n e c r o s sh e a d p u m p1）主机燃油单元 F u e l o i l u n i t o f M.E8）付机海水泵 G e n e r a t o r e n g i n e s e aw a t e r p u m p2）付机燃油单元 F u e l o i l u n i t o f A.E9）付机缸套水泵 G e n e r a t o r e n g i n ec y l i nde r c o o l i n gw a t e r p u m p3）粘度计 V i s c o s i t y c o n t r o l l e r10）锅炉给水泵 F e e d w a t e r p u m p o fb o i l e r泵 P u m p11）锅炉燃油泵 F u e l o i l p u m p o fb o i l e r1）主机滑油泵 M a i n e n g i n e l u b r i c a t i n g o i lp u m p 12）分油机供给泵 F u e l o i l s u p p l y p u m po f p u r i f i e r2）主机缸套水泵 M a i n e n g i n e c y l i n d e rc o o l i n g w a t e r p u m p 13）制淡海水泵 S e a w a t e r p u m p o ff r e s h w a t e rg e n e r a t o r3）主机缸套水预热泵 M a i n e n g i n e c y l i n d e rc o o l i n g w a t e r p r e h e a t i n gp u m p14）压载泵 B a l l a s t p u m p4）主机海水泵 M a i n e n g i n e s e a w a t e r p u m p 15）舱底消防泵 B i l g e a n d f i r e p u m p 373817）油渣泵 S l u d g e o i l p u m p2、柴油澄清舱 D i e s e l o i l s e t t i n gt a n k18）柴油输送泵 D i e s e l o i l t r a n s p o r t p u m p 3、燃油日用柜 F u e l o i l d a i l y t a n k 19）燃油油输送泵 F u e l o i l t r a n s p o r t p u m p4、燃油澄清舱 F u e l o i l s e t t i n g t a n k 20）汽缸油输送泵 C y l i n d e r o i l t r a n s p o r t p u m p 5、滑油澄清舱 L u b r i c a t i n g o i ls e t t i n g t a n k21）淡水输送泵 F r e s h w a t e r t r a n s p o r t p u m p 6、滑油储藏舱 L u b r i c a t i n g o i l s t o r et a n k22）热水循环泵 H o t w a t e r c i r c u l a t i n g p u m p 7、滑油循环舱 L u b r i c a t i n g o i lc i r c u l a t i n g t a n k 23）饮水日用泵 D r i n k i n g w a t e r p u m p8、燃油溢油舱 F u e l o i l o v e r f l o wt a n k舱底消防总用泵 B i l g e,f i r e a n d G.S p u m p9、燃油油渣舱F u e l o i l s l u d g e t a n k 喷淋泵 S p r i n k l i n g p u m p10燃油深舱 F u e l o i l d e e p t a n k 停泊海水泵 H a r b o r s e a w a t e r p u m p11滑油污油舱 L u b r i c a t i n g d i r t y o i lt a n k12滑油溢油舱 L u b r i c a t i n g o i lo v e r f l o w t a n k二、各种舱（箱）柜 A l l k i n d s o f t a n k13滑油油渣打舱 L u b r i c a t i n g o i ls l u d g e t a n k1、柴油日用柜 D i e s e l o i l d a i l y t a n k14主机淡水膨胀水箱 M.E f r e s h w a t e r e x p a n s i o n t a n k15付机淡水膨胀水箱 A.E f r e s h w a t e r e x p a n s i o n t a n k394016、淡水压力柜 F r e s h w a t e r p r e s s u r e t a n k 1、滑油系统 L u b r i c a t i n g o i lp i p i n g s y s t e m17、热水压力柜 H o t w a t e r p r e s s u r e t a n k2、燃油系统 F u e l o i l p i p i n gs y s t e m18、饮水压力柜 D r i n k i n g w a t e r p r e s s u r et a n k 3、海水系统 S e a w a t e r p i p i n gs y s t e m19、淡水舱 F r e s h w a t e r t a n k4、缸套水系统 C y l i n d e r c o o l i n gw a t e r p i p i n g s y s t e m 20、饮水舱 D r i n k i n g w a t e r t a n k5、启动空气系统 S t a r t a i r p i p i n gs y s t e m21、锅炉水舱 B o i l e r w a t e r t a n k6、控制空气系统 C o n t r o l a i r p i p i n gs y s t e m22、分油机工作水箱 P u r i f y o p e r a t i n g w a t e r t a n k 7、排气系统 E x h a u s t p i p i n g s y s t e m23、汽缸油日用柜 C y l i n d e r o i l d a i l y t a n k8、日用供水系统 D a i l y w a t e r p i p i n gs y s t e m24、尾管滑油重力柜 G r a v i t y t a n k o f t u b e o i l9、蒸汽系统 S t e a m p i p i n g s y s t e m25、排气水封箱 E x h a u s t s e a l w a t e r t a n k10、锅炉给水和凝水系统 F e e d w a t e r a n d c o n d e n s a t e o f b o i l e r pi p i n g s y s t e m26、蒸馏水水舱 D i s t i l l i n g w a t e r t a n k11、燃油净油系统 F u e l o i l p u r i f i e dp i p i n g s y s t e m27、污水井 B i l g e w e l l12、燃油输送系统 F u e l o i l t r a n s p o r tp i p i n g s y s t e m三、各种管系系统 A l l k i n d s o f p i p e s3341舵销 R u d d e r p i n t l e13、滑油净油系统 L u b r i c a t i n g o i lp u r i f i e d p i p i n gs y s t e m舵杆衬套 r u d d e r s t o c k l i n e r14、滑油输送系统 L u b r i c a t i n g o i lt r a n s p o r t p i p i n gs y s t e m舵杆轴套 S l e e v e f o r r u d d e r s t o c k15、舱底压载系统B a l l a s t a n d b i l g ew a t e r p i p i n g s y s t e m 舵销承衬套 B u s h f o r r u d d e r p i n t l e四、仪表类 I n s t r u c t i o n s舵销轴套 S l e e v e f o r r u d d e r p i n t l e1、压力表 P r e s s u r e g a u g e上舵承底座 R u d d e r c a r r i e r s e a t2、真空表 V a c u u m g a u g e舵销承座 P i n t l e b e a r i n g3、温度计 T h e r m o m e t e r 舵杆承座 R u d d e r s t o c k b e a r i n g4、吨位表 D W T g a u g e挡圈 R e t a i n i n g r i n g5、遥测表 D i s t a n t s u r v e y g a u g e 舵柄 T i l l e r6、液全器 L e v e l s w i t c h7）舵角 T h e a n g l e o f r u d d e r5、空压机 A i r c o m p r e s s o r1）主空压机 E m e r g e n c y a i r c o m p r e s s o r2）应急空压机42437、传感器 S e n s o r12、机控室 E n g i n e c o n t r o l r o o m五、其它 O t h e r s13、台虎钳 V i s e(=v i c e)1、风机 F a n14、表铜截止阀 B r o n z e c l o s e v a l v e2、防海生物装置 A n t i-f o u l S T M p l a n t15、表铜截止止回阀B r o n z e c h e c k v a l v e3、泡沫柜 A i r f o a m t a n k16、铸铁截止阀 C a s t i r o n s t o p v a l v e4、中间轴 M i d d l e s h a f t17、铸铁截止止回阀 C a s t i r o n c h e c k a n d s t o p v a l v e5、尾轴 P r o p e l l e r s h a f t18、调节阀 A d j u s t a b l e va l v e6、螺旋桨 P r o p e l l e r19、溢流阀、安全阀R e l i e f v a l v e7、中间轴承 L i n e s h a f t b e a r i n g20、减压阀 R e d u c i n g v a l v e8、泡沫灭火机 F o a m f i r e e x t i n g u i s h e r六、材料 M a t e r i a l9、饮水消毒装置 S t e r i l i z e r p l a n t1、管子 P i p e10、主配电板 M a i n s w i t c h b o a r d2、无缝钢管 S e a m le s s s t e e l p i p e(t u b e)11、机舱集控台 E n g i n e r o o m c o n t r o l c o n s o l e 3、紫铜管 P u r p l e c o p p e r p i p e 44454、铁法兰 I r o n f l a n g e18、支架（马脚） C l a m p5、铜法兰 C o p p e r f l a n g e19、油漆 P a i n t6、盲板法兰 B l i n d-f l a n g e20、备件 S p a r e p a r t s7、螺丝（螺栓） B o l t8、双头螺丝 S t u d七、生产工具 P r o d u c e t o o l9、螺帽（螺母） N u t1、图纸 D r a w i n g10、不锈钢螺丝 S t a i n l e s s s t e e l b o l t2、活络钣 A d j u s t a b l e s p a n n e r11、垫片（床） G a s k e t3、令司板（梅花钣） R i n g s p a n n e r12、橡皮床 G u m g a s k e t4、开口钣 O p e n–e n d e r s p a n n e r13、纸箔床 P a p e r c o p p e r g a s k e t5、管子钳 P i p e w r e n c h14、紫铜床 P u r p l e c o p p e r g a s k e t6、凿子 C h i s e l15、石墨床 B l a c k l e a d g a s k e t7、锒头 H a m m e r16、青铅床 B l a c k l e a d g a s k e t8、锉刀 F i l e17、佛纳 F e e l e r g a u g e9、螺丝刀 S c r e w d r i v e r464710、油漆滚筒 P a i n t r o l l e r4、首先请检查安装说明和电气绝缘11、油漆刷子 P a i n t b r u s h P l e a s e c h e c k t h e c o nd i t i o n o fi n s t a l l a t i o n a n d i n s u l a t i o n f i r s t12、钢锯 H a c k s a w5、我们准备将油水分离器动转13、套筒扳手 S o c k e t s p a n n e r N o w w e w i l l r u n t he o i l y-w a t e r s e p a r a t o r14、手电筒 T o r c h6、请检查动转情况15、钻头 d r i l l e r P l e a s e c h e c k t h e r u n n i n g c o nd i t i o n八、英语会话 7、接着我们一个一个地做报警/安全保护装置的功能试验1、早上好 g o o d m o r n i n g N o w w e w i l l d o t h e f u n c t i o n t e s t a b o u ta l a r m a n d s a f e t y d e v i c e2、今天我们准备交验油水分离器 8、设备交接基本结束T o d a y w e w i l l t e s t t h e o i l y-w a t e r s e p a r a t o r.N o w t h e t e s t i s o v e r3、请跟我来 9、请部有何修改意见？P l e a s e f e l l o w m e.D o y o u h a v e a n y q u e s t i o n?484910、非常感谢 17、这里增加一只落水斗T h a n k s A d d a d r a i n p l u g h e r e11、再见 18、请用空气压缩空气吹干G o o d b y e P l e a s e d r y i t b y t h e c o m p r e s s e d ai r12、请把这对法兰撬紧松开 19、我将回车间支拿肥皂水P l e a s e t i g h t e n/r e l e a s e t h e f l a n g e I w i l l c o m t o m y w o r k s h o p t o t a k e s o m e s o a pw a t e r13、这路管子是从发电机单元来的 20、这个系统非常重要的，一定要认真检查 T h e p i p i n g i s f r o m t o t h e G/E u n i t T h i s s y s t e m i s v e r y i m p o r t a n t,p l e a s ec h e c k i t c a r e f u l l y14、这对法兰/接头在漏 21、请交验收整改意见T h i s f l a n g e/c o n n e c t i o n i s l i n k i n g P l e a s e ch e c k y o u r r e m a r k s15、这路系统的试验压力是7公斤 22、天太热了，请休息一会T h e t e s t p r e s s u r e o f t h e p i p i n g s y s t e m i s7ba r I t’s t o o h o t,p l e a s e t a k e a r e s t16、这里请加强 p l e a s e m a k e a c l a m p h e r e23、我负责这项工作 I a m i n c h a r g e o f t h i sj o b电气部分 E L E C T R I C P A R T5051一、常用词汇 W o r d s a n d e x p r e s s i o n模拟 A n a l o g(u e)2182千赫值班接收机 2182K H z w a t c h r e c e i v e r锚灯 A n c h o r l i g h tA异常 A b n o r m a l风速风向仪 A n e m o r u m b o m e t e r应答 A c k n o w l e d g e阳极 A n o d e有功功率 A c t i v e p o w e r天线 A n t e n n a执行器 A c t u a t o r天线馈线连接器 A n t e n n a f e e d e rc o n n e c t o r调整 A d j u s t天线引入绝缘端子 A n t e n n a l e a d i n g–i ni n s u l a t o r空气断路器 A i r c i r c u i t b r e a k e r天线共用器 A n t e n n a m u l t i c o u p l e r 报警系统 A l a r m s y s t e m天线调谐器 A nt e n n a t u n e r交流电 A l t e r n a t i n g c u r r e n t电焊机 A r c w e l d e r 电流表 a m m e t e r声音的 A u d i b l e放大器 A m p l i f i e r自动海图标绘仪 A u t o c h a r t p l o t t e r自动舵 A u t o p i l o t自动的 A u t o m a t i c5253自动雷达标绘仪 A u t o m a t i c r a d a r p l o t t i n ga i d 球鼻首警告灯 B u lb o u s b o w w a r n i n gl i g h t自动电话 A u t o m a t i c t e l e p h o n e汇流排 B u s(-)b a r 电压自动调节器 A u t o m a t i c v o l t a g e r e g u l a t o r 汇流排 B u s–t i e–i n自动化系统 A u t o m a t i o n s y s t e m蜂鸣器 B u z z e r压载控制台 B a l l a s t c o n t r o l c o n s o l e C、电缆 C a b l e镇流器 B a l l a s t电缆填料函 C a b l e g l a n d底座 B a s e敷设电缆 C a b l e l a y i n g电池 B a t t e r y电缆管 C a b l e p i p e(c o n d u i t)铃 B e l l 电缆扎带 C a b l e s t r a p弯曲 B e n d电缆托架 C a b l e t r a y床头灯 B e r t h l i g h t校准器 C a l i b r a t o r失电 B l a c k o u t电容 c a p a c i t o r刹车 B r a k e阴板 C a t h o d e电刷 B r u s h警告牌 C a u t i o n p l a t e5455顶灯 C e i l i n g l i g h t通讯 C o m m u n i c a t i o n中央处理器 C e n t r a l p r o c e s s i n g u n i t计算机 C o m pu t e r通道 C h a n n e l接头 C o n n e c t o r充电器 C h a r g e r恒电流 C o n s t a n t c u r r e n t充放电板 C h a r g i n g&d i s c h a r g i n g b o a r d 消耗 C o n s u m p t i o n海图灯 C h a r t t a b l e l i g h t触头 C o n t a c t检查 C h e c k接触器 C o n t a c t o r芯片 C h i p控制箱 C o n t r o l b o x清洁 C l e a n控制箱 C o n t r o l l e r雨雪清除器 C l e a r v i e w s c r e e n芯线 C o r e二氧化碳释放报警 C O2r e l e a s e a l a r m角灯 C o r n e r l i g h t同轴电缆 C o a x i a l c a b l e计算器 C o u n t e r线圈 C o i l电流 C u r r e n t冷库呼叫 C o l d s t o r e c a l l i n g D、损坏 D a m a g e5657危险气体报警箱 D a n g e r o u s g a s d e t e c t i n g&a l a r m b o x 双极单刀开关 D o u b l e p o l e s i n g l ew a y s w i t c h白昼信号灯 D a y l i g h t s i g n a l l i g h t双极双刀开关 D o u b l e p o l e t w o w a ys w i t c h去耦 D e c o u p l i n g s e t天线收发转换开关 D u p l e x e r 台灯 D e s k l i g h t值班水手呼叫 D u t y s a i l o r c a l l i n g 控测器 D e t e c t o r接地 E a r t h拨号 D i a l接地排 E a r t h b a r数字选择呼叫收信机 D i g i t a l s e l e c t–c a l lr e c e i v e r测深仪 E c h o s o u n d e r调光器 d i m m e r电工试验板 E l e c t r i c t e s t p a n e l 直流电 D i r e c t c u r r e n t电机员 E l e c t r i c a l e n g i n e e r 直接起动 D i r e c t–o n–l i n e s t a r t i n g 电极 E l e c t r o d e 磁盘 D i s k应急照明分电箱 E m e r g e n c e l i g h t i n gd i s t r i b u t i o n b o x显示 D i s p l a y应急示位标 E m e r g e n c e p o s i t i o ni n d i c a t i n g r a d i ob e ac o n遇险信息控制器 D i s t r e s s m e s s a g e c o n t r o l l e r 应急停 E m e r g e n c e s t o p多普勒记程仪 D o p p l e r s p e e d l o g5859应急配电板 E m e r g e n c y s w i t c h b o a r d馈电品 F e e d e r p a n e l机舱报警 E n g i n e a l a r m滤波器 F i l t e r集控台 E n g i n e c o n t r o l c o n s o l e火警复显器 F i r e a l a r m r e p e a t e r机舱监测报警 E n g i n e r o o m m o n i t o r i n g&a l a r m s y s t e m 防火风闸控制单元 F i r e d a m p e r c o n t r o lu n i t轮机员呼叫 E n g i n e e r c a l l i n g p a n e l火警检测箱 F i r e d e t e c t i n g b o x 轮机员安全 E n g i n e e r s a f e t y s y s t e m火焰探头 F l a m e d e t e c t o r增强群呼叫收讯机 E n h a n c e g r o u p c a l l r e c e i v e r 闪光灯 F l a s h l i g h t交换机 E x c h a n g e r浮充电 F l o a t c h a r g e防爆灯 E x p l o s i o n p r o o f l i g h t强光灯 F l o o d l i g h t延伸报警板 E x t e n s i o n a l a r m p a n e l流程图 F l o w c ha r t故障 F a i l u r e流量开关 F l o w s w i t c h故障 F a u l t荧光灯 F l u o r e s c e n t l i g h t 反馈 F e e d b a c k雾笛 F o g h o r n频率 F r e q u e n c y6061熔丝 F u s e感温探头 H e a t d e t e c t o r填料 G a s k e t底座 H o l d e r通用报警 G e n e r a l a l a r m电笛、喇叭 H o r n发电机 G e n e r a t o r病房呼叫 H o s p i t a l c a l l i n g 发电机屏 G e n e r a t o r p a n e l照明 I l l u m i n a t i o n （铜）锣、钟 G o n g白炽灯 I n c a n d e s c e n t l i g h t 全球卫星定位导航 G P S n a v i g a t o r指示器 I n d i c a t o r组合灯板 G r o u p a l a r m l i g h t p i l l a r卫星B站 I N M A R S A T B s t a t i o n 组合起动屏 G r o u p s t a r t e r p a n e l卫星C站 I N M A R S A T C s t a t i o n 电罗经 G y r o c o m p a s s输入输出 I n p u t/o u t p u t卤素灯 H a l o g e n l i g h t安装 I n s t a l l听筒 H a n d s e t仪表 I n s t r u m e n t硬件 H a r d w a r e绝缘胶带 I n s u l a t i n g t a p e航向 H e a d i n g绝缘 I n s u l a t i o n6263接口、界面 I n t e r f a c e限位开关 L i m i t s w i t c h连锁 I n t e r l o c k连接 L i n k中断 I n t e r r u p t负载 L o a d逆变器 I n v e r t e r劳莱收信机 L o r a n r e c e i v e r接线盒 J u n c t i o n b o x磁罗经 M a g n e t i c c o m p a s s 键盘 K e y b o a r d主机电子调速器 M a i n e n g i n ee l e c t r o n i c g o v e r n o r 灯泡 L a m p主机功率、纽力仪M a i n e n g i n e p o w e r&。
船舶简称
船舶简称各种船型英文缩写（一）按照字母首位顺序排列：1. Bulk Carrier （散货船）其类型分类有：-Handysize （灵便型）：2〜5万吨左右，大灵便型：大于4万吨-Panamax （巴拿马型）：6〜7.5万吨，船的总长小于或等于274.32M，型宽小于或等于32.30M ;目前平均载重吨达到8.2万吨-Kmsarmax （卡尔萨姆型）：8〜8.9999万吨-Capesize （好望角型）:15万吨左右2. Co nta in er （集装箱）（货舱区分：中央部位货舱一一集装箱船；其他舱位一一普通杂货船可变换区分：货舱内结构可拆装一一集装箱船；不可拆装一一普通杂货船）3.Oil Tan ker （油轮）其类型分类有：-ULCC（巨型原油轮）:大于30万吨-VLCC（超大原油轮）：20〜30万吨-Suezmax（苏伊士型）：12〜16万吨-Aframax（阿芙拉型）：8〜12万吨-Panamax（巴拿马型）：6〜8万吨各种船型英文缩写（二）按照字母首位顺序排列：BBC:Bulk Carrier 散货船CCOT:Cargo Oil Tanker 货油轮DDFF:高速渡轮EERRV:救援船FFLNG:浮式液化天然气船（科代替岸上传统的液化天然气工厂）FPSO:浮式生产储油船FPV:浮式生产设备GG-Cargo Ship:杂货船LLNG:液化天然气船LEG:液化乙烯汽船LPG:全压式液化石油汽船LSV:驳运支援船LR成品油轮：stands for large range, 远程成品油轮MMR成品油轮:stands for medium range, 中程成品油轮OOSV:Offshore Support Vessel, 海洋工程船PPSV:平台供应船PC:重型石油化学制品运输船PCC:Pure Car Carrier 汽车运输船PCTC:Pure Car & Truck Carrier 大型轿车卡车专用船RRO-RO SHIP:客滚船Roll-o n/Roll-off ship: 滚装船UUCLL: Ultra Large Crude Carrier: 超大型原油轮VVLOC:大型矿砂船VLCC:巨型原油轮1、DWTDWT是DEAD WEIGHT TONNAGE的缩写，是表示“载重吨”。
船舶常用英语(一)
船舶常用英语(一)一、船舶类型常用英语ship, vessel 船，船舶boat, craft 艇sampan舢板, 小船manpowered boat人力船sailor; sailing boat 帆船motor sailor 机帆船power-driven ship 机动船paddle steamer, paddle wheel vessel 明轮船screw ship; propeller vessel 螺旋桨船airscrew ship; aerial propeller vessel 空气螺旋桨船hovercraft; aircushioncraft 气垫船hydrofoil水翼船hydrojet propelled boat, water jet boat 喷水船steamship; steamer 蒸汽机船motor ship 内燃机船diesel ship 柴油机船electrically-propelledship 电力推进船steam turbine ship 汽轮机船gas turbine ship 燃气轮机船nuclear-power ship核动力船deck ship 甲板船flush deck ship 平甲板船raised quarter-deck shipVLCC (very large crude carrier) (吨位在20万至30 万吨之间的) 巨型油轮ULCC (ultra-large crude carrier) (吨位在30万至50万吨之间的) 超巨型油船refrigerated ship; cold storage ship 冷藏船roll-on/roll-off ship(RO/RO ship) 滚装船ferry渡船passenger ferry 旅客渡船freight ferry 货物渡船fishing vessel(boat) 渔轮trawler拖网渔轮barge carrier; lighteraboard ship(LASH)载驳船barge; lighter 驳船deck barge 甲板驳well-deck barge 半舱驳double shell barge 双壳驳single side barge 单舷长大舱口驳oil barge 油驳container barge 集装箱驳船RO/RO barge 滚装驳船liquefied gas barge 液化气体驳hopper barge 开底泥驳split hopper barge 对开泥驳pusher; pushboat 顶推船；推船working ship 工程船tug; tugboat; towboat 拖船harbor tug 港作拖船rescue tug 救助拖轮salvage ship 救捞船dredger挖泥船trailing suction dredge 耙吸挖泥船cutter suction dredger 绞吸挖泥船bucket wheel dredger 斗轮挖泥船bucket dredger 链斗挖泥船reclamation craft吹泥船grab dredger 抓斗挖泥船dipper dredger 铲斗挖泥船floating pitter; drive pitter 打桩船floating crane; derrick boat 起重船floating dock 浮船坞cable layer; cable ship 布缆船scientific surveying ship 科学考察船research ship 科学调查船oceanographic research vessel 海洋调查船surveying ship 测量船ice-breaker破冰船pontoon 浮舟; 浮桥; 趸船, 浮码头high speed craft 高速船passenger catamaran 双体客船vehicle ferry catamaran 双体车辆渡船vehicle-passenger ferry catamaran 双体车客渡船pontoon catamaran 双体趸船二、船舶结构常用英语center line 中心线，中线athwartships 横对船体（与船首尾线直交）bevel斜角；斜面base line 基线amidships 在船中部；在纵中线上designed waterline breadth 设计水线宽designed waterline length 设计水线长draft吃水former/aft draft 首/尾吃水draft figures 吃水尺度intersection 交点；交叉；横断面knuckle折角线length between perpendicular 垂线间长length overall 总长load waterline length 满载水线长register length (breadth;depth) 登记长度（宽度、深度）freeboard干舷rise of floor (dead; rise) 舭高；船底loadlinemark载重水线标记fresh water load line (F.) 淡水载重线fresh water timber load line (L.F.) 淡水木材载重线tropical fresh water load line (TF) 热带淡水载重线tropical load line (T) 热带载重线summer load line(S) 夏季载重线summer freshwater load line(F) 夏季淡水载重线winter load line(W) 冬季载重线winter North Atlantic load line(WNA) 冬季北大西洋载重线even keel （首尾）等吃水，平载extreme breadth 最大宽度floatable length 可浸长度sheer at forward (after) perpendicular 首尾舷弧sheer line 舷弧线accommodation居住舱室accommodation deck 起居舱室；旅客甲板accommodation ladder舷梯accommodation ladder platform 舷梯平台accommodation laddermanrope 舷梯扶索after body 后（部船）体after peak bulkhead 艉尖舱舱壁after peak tank 艉尖舱air hole 空气孔air pipe 空气管appendage （船体水线下的）附体；附件auxiliary machinery 辅助机械；辅机balanced rudder 平衡舵ballast压载（物）ballast line压载水管系ballast pump 压载水泵ballast pumping system 压载水系统ballast tank(water) 压载舱（水）batten 板条；压条（封仓用）batten-ceiling （货舱内）护舱条，护板beam横梁beam bracket 梁肘板bearding 交合线，榫（艏柱或艉柱上）bending moment 弯矩bilge 舭部；舱底；（船底）污水沟bilge bracket 舭肘板bilge keel(chock, piece) 舭龙骨bilge knee 舭肘板bilge line 舭水管系bilge main 舭水总管bilge pipe (suction) 舭吸水管bilge pump 舭水泵bilge strake(plate) 舭列板bilge well 污水井bitt系缆桩bollard 系缆桩；系船柱；双系柱bolster枕垫bonnet烟囱帽；机罩boom 杆；吊杆；桁；叉架boom crutch(support; rest) 吊杆支架bossing 尾管突出部；轴包套bottom frame 船底横骨bottom longitudinal 船底纵骨bottom plate 船底板bow船首，船头bow fender 艏护垫bow flare 艏部外飘bow thruster 首侧推器bracket 肘板；（三角）拖架breakwater挡浪板bridge桥；桥楼；驾驶台bulb angle 圆头角材bulbous bow 球形船首，球鼻首bulb stern 球形船尾bulkhead舱壁bulkhead plating 舱壁板bulkhead stiffener 舱壁扶强材bulwark舷墙bulwark plating 舷墙板bulwark stay 舷墙扶强材bunker tank燃料舱bushing衬套butt端接；残片butt joint(seam) 平接缝butt riveting 对接铆butt welding 对接焊butterfly clip 蝴蝶夹bypass valve 旁通阀cable stopper 止链器camber翘曲camber of beam 梁拱cant beam 斜梁cant bracket 斜角板cant frame 斜肋骨cantilever悬臂梁capstan绞盘；绞缆机cargo batten 货舱护板cargo block 吊货滑车cargo port 装货舷梯，舷门cat walk （油轮上的）天桥，步桥center girder 中底桁center strake 中央内底板chafing plate 防擦板chafing ring防擦环chain lock(well) 锚链舱chain pipe 锚链管chain stopper 止链器chock导缆器；垫木clamp plate 夹板，压板cleat 羊角；系绳铁栓；防滑条coaming围板；舱口围板cofferdam隔离舱collar plate 封板collision bulkhead 船首舱壁；防撞舱壁companion way(hatch) 升降口corrugated bulkhead 槽形舱壁corrugation皱；槽形；波形cross deck structure 舱间甲板结构crossing strength member 交叉强力构件cruiser stern 巡洋舰型船尾curtain plate 幕板cut out 开口；切davit吊艇架；吊艇柱deck甲板deck beam 甲板横梁deckhouse甲板室deck line甲板线deck longitudinal 甲板纵骨deck stringer(plate) 甲板边板deep tank 深舱derrick吊杆diaphragm隔板double bottom 双层底doubling plate 双层焊合板drain hole 排水孔duct keel 箱形龙骨dunnage 垫舱（物料）；衬垫dunnage wood 垫木dynamic load 动载荷end bracket 端肘板escape trunk （船内）应急通道engine bed 机座engine casing 机舱围壁escape scuttle （船内）应急出口escape vent 脱险口expansion joint 伸缩接头expansion trunk(tank) （油船）膨胀深井extension bracket 延伸肘板face plate 面板fender碰垫；护舷材fender bar 护舷条fair lead 导缆器flame screen 防焰罩flange折边flanged bracket 折边肘板flat keel 平板龙骨floor肋板folding door 折门forecastle deck 艏楼甲板fore peak tank （船的）首舱；前尖舱forward perpendicular 首垂线foundation底座frame肋骨frame number 肋骨跨数frame space 肋距freeing port 甲板排水孔；放水孔gangway (gang ladder or gang board) 舷梯gasket 垫圈，垫料（集）密封垫general service pipe (G.S pump) 通用泵，总用泵girder桁材gooseneck(parity iron) 鹅颈头；吊杆弯头grating格子板；滑铁板ground tackle 锚泊索具gunwale舷缘；舷边gunwale angle 舷边角钢gunwale bar 舷边角材gunwale railing 舷边栏杆gunwale tank 舷侧水柜（甲板下）gusset角板；扣板gutter （甲板）水沟；槽沟gutter angle; waterway angle （舷侧）排水沟角钢gypsy 绞筒（锚机绞车上的）handrail舷墙扶手hanging rudder; hinged rudder 吊舵；悬舵hatch; hatchway; hatch opening 舱口hatch bar 封舱压条hatch batten 舱口边压条hatch beam (web) 舱口大梁hatch booby 活动舱口盖hatch coaming 舱口板hatch cover 舱口盖hatch end beam 舱口端梁hatch moulding 舱口椽材hatch side girder 舱口纵桁hatch tarpaulin盖舱布hatch trunk 舱口围阱hawse pipe 锚链管hawser绳索；大缆heel踵材；横倾hinged cover(door) 铰链盖（门）hold货舱hold beam 舱内梁hold frame 舱内肋骨hold ladder 舱内梯hold stanchion(pillar) 舱内支柱hold stringer 舱内纵桁hopper漏斗；开舱泥驳hopper tank 底边舱hopper tank sloping plating 底边舱斜板horizontal margin plate 水平内底板horizontal girder 水平桁horizontal stiffener 水平扶强材（防挠材）hull船壳，船体hull construction 船体结构hull plating 船壳板hull strength 船体强度inner bottom 内底inner bottom plating 内底板insert plate 嵌板；衬板jack千斤顶jack ladder 绳梯Jacob's ladder 软梯；绳梯Joggled joint 折接；弯合joggling machine 折曲机keel龙骨keelblock龙骨墩keel line 龙骨线；艏艉线keel plate 龙骨板keel rail （救生艇）艇底把手keelson内龙骨kingpost起重柱；将军柱knee肘板；弯头knee of the deck 甲板梁肘板lightening hole 减轻孔lignum vitae 铁梨木local strength 局部强度local stress 局部应力longitudinal纵骨；纵材；纵桁longitudinal bulkhead 纵舱壁longitudinal bending 纵向弯曲longitudinal framingsystem 纵骨架式longitudinal strength 纵向强度lug耳板main deck 主甲板main frame 主肋骨manhole人孔man hole door 人孔盖man hole coaming 人孔围板moment of inertia 惯性矩margin plate 内底边板molded breadth 型宽molded depth 型深mooring hole 导缆孔mooring post 系缆柱；岸柱mud box 泥箱non-return valve 止回阀non-watertight bulkhead 非水密舱壁notch 切口；槽口；刻痕oscillating load 振动负荷parallel middle body 平行中体panel stiffener 板格扶强材panting arrangement 防挠振结构panting beam 防挠振梁panting stringer防挠振纵桁pillar支柱；墩pintle舵销plane bulkhead 平面舱壁plane keel 平板龙骨pump room 泵舱helm(rudder) pintle 舵销horizontal margin plate 水平内底边板out bottom plating 外底板platform平台plating壳板plimsoll mark 载重线标志poop艉楼；船尾poop deck 艉楼甲板port 舷门；舱门；（装货）口；窗；门；孔porthole 舷窗；（装货）舷门propeller; propellor 推进器；螺旋桨propeller aperture 螺旋桨空间propeller boss(bub) 螺旋桨毂propeller shaft 艉轴racking（船体）横向挠度rail扶手；栏杆rolling横摇round of beam梁拱round stern 圆（船）尾rudder舵rudder carrier 舵托rudder casing 舵杆管rudder pintle 舵针；舵栓rudder plate; rudder blade 舵叶；舵板rudder post 舵柱rudder stock 舵杆rudder trunk 舵杆围壁；舵杆管rung （梯子）踏步；横档scallop扇形开孔scantling构件尺寸scantling of the structure 结构尺寸scarf; scarph 嵌接处；斜面；斜接scarf joint 斜（嵌）接scarf weld （斜面）焊接scarfing bracket 嵌接肘板scupper排水孔scupper pipe 排水管scuttle 舷窗；人孔（盖）；小舱口盖seam焊缝；接缝section剖面section modulus剖面模数semi-balanced rudder半平衡舵shaft轴shaft bracket 轴架shaft tube; stern tube 艉轴管shaft tunnel(alley; passage;trunk) 轴隧；地轴弄shedder plate 泄板；斜板sheer舷弧；偏航sheer strake 舷顶列板shell船壳；壳shell frame 舷侧肋骨shell plating 船壳板；外板shell strake; outside plating 船体外板shelter deck 遮蔽甲板shifting beam 活动舱口梁shifting board (or plank) 止移板（散装谷类）；防动板side girder 旁桁材side longitudinal 舷侧纵骨side plating 舷侧外板side strake 舷侧列板single bottom 单层底skid护舷木；垫板skylight天窗slanting plate 斜板slop tank 污油水舱sloping plate 斜板sloping plate longitudinal 斜板纵骨slot槽；开缝sluice水密门；水闸sluice valve 闸阀sniped end 削斜端soft toe 软趾solid floor 实肋板sounding pipe 测量管；测深管stabilizer减摇装置stabilizing tank 减摇水舱staging 构架；台架；脚手架stanchion支柱；栏杆柱static load 静载荷stay 支柱；撑条；支索stay bar(or rod) 撑杆stay plate 撑板stem艏；艏柱；艏材stem post 艏柱stern船尾，艉部stern counter 船尾突出体stern shaft; propeller shaft 艉轴stern poop 艉楼stern post 尾柱stiffener 防挠材；扶强材；加固物stool托架，座，凳strake列板strength calculation 强度计算strength deck 强力甲板stringer纵桁stringer plate 甲板边板structural member 构件structural strength结构强度strum box （舱底水）过滤箱strut 撑材，支柱，轴架stuffing box 填料箱superstructure上层建筑tail (end) shaft 艉轴tarpaulin 防水油布，帆布，舱盖布thrust bearing(block) 推力轴承thrust shaft collars 推力环tieplate 带板，牵板，连接板topside tank 顶边舱；上边柜topside tank sloping plating 顶边舱斜板torsion扭转torsion strength 扭转强度transom stern 方形船尾transverse横梁，横材transverse bulkhead 横舱壁transverse frame 横肋骨，横框transverse framing system 横骨架式transverse ring 横环transverse strength 横向强度tripping bracket 防倾肘板tween deck 中间甲板tween deck frame 甲板间肋骨twisting distortion 扭转变形twisting moment 扭转力矩tunnel 轴隧，隧道，风筒tunnel escape 轴隧应急出口tunnel shaft bearing 中间轴支撑轴承ullage pipe (port) 油位测定管（孔）ullage space 空挡空间upper deck 上甲板upper (reverse) frame 内底横骨upper (lower) shelf plate 上（下）支架板upper (lower) stool上（下）托架ventilator通风筒vertical ballast trunk 竖向压载通道vertical girder 竖桁warping chocks 滚轮导缆钳wash bulkhead 可荡舱壁，挡水舱壁watertight bulkhead 水密舱壁watertight deck 水密门weather deck 露天甲板web beam 强横梁，桁板横梁web frame 加强肋骨，框架肋骨，桁板肋骨web plate 腹板wedge楔木，楔子winch起货机winch-head绞车卷筒windlass起锚机wing tank 翼舱，翼柜wire clip 钢缆夹wire reel 卷缆车，钢丝滚筒三、船舶材料及工艺常用英语A.Shipbuilding material(造船材料)T-bar T型钢Z-bar Z型钢I-Bar 工字钢channel bar 槽钢angle steel 角钢equal angle steel 等边角钢unequal angle steel 不等边角钢offset bulb plate 球扁钢flat plate 钢板round steel 圆钢half round steel 半圆钢steel pipe 钢管alloy steel 合金钢special steel 特种钢tempering steel 回火钢材low carbon steel 低碳钢high tensile steel 高强度钢copper 紫铜brass 黄铜aluminum alloy 铝合金stainless steel 不锈钢mechanical property 机械性能tensile test 拉伸试验bend test 弯曲试验impact test 冲击试验torsion test 扭转试验torsion strength 抗扭强度torsional deflection 扭转；扭转变形tensile strength 拉伸强度yield strength 屈服强度yield point 屈服点yield stress 屈服应力elastic limit 弹性极限ultimate strength 极限强度ultimate tensile stress 极限拉伸应力elasticity 弹性ductility 延展性，可塑（锻）性flexibility 挠性，柔性，易弯性toughness 韧性brittleness 脆性friability 易碎性hardness 硬度rigidity 刚性，稳定性heat treatment 热处理quench 淬火normalising 正火annealing 退火hardening 硬化，淬火tempering 回火casting 铸件，铸造forging 锻件，锻造pickling 酸洗ship timber 船用木材lignumvitae 铁梨木three-plywood 三夹板asbestos 石棉asbestos cloth 石棉布asbestos board 石棉板asbestos sheet 石棉纸asbestos cord 石棉绳asbestos paint 石棉涂料fiberglass 玻璃丝plastics 塑料resin 树脂rubber 橡皮painting 油漆cladding 镀层，表面处理coating 涂层，敷料corrosion 腐蚀，侵蚀wastage 损耗，蚀耗wear and tear 蚀损，磨损fracture 裂纹fatigue fracture 疲劳裂纹hairline fracture 发式裂纹buckling 皱折deformation 变形deflection, deflexion 挠曲flexion 弯曲lamellar tearing 层间撕裂rust 铁锈scale 锈皮pitting 点蚀，锈斑indent 凹痕，凹陷groove 槽沟detachment 脱开，脱焊rupture 断裂，破裂cropping 割掉renewal 换新descale 除锈grind 磨平be veed out 刨除alignment 对准，校直snip 剪断，剪片taper 削斜，斜度B.Shipbuildingworkmanship （造船工艺）Working drawing 施工图end elevation 后面图front elevation 正面图side elevation 侧面图plane 平面图lines plan 型线图plan of waterlines 水线图general arrangement plan 总布置图construction plan 结构图damage plan 损坏示意图shell expansion plan 外板展开图docking plan 进坞图framing plan 船体构架图inboard profile plan 纵剖面图midship section plan 舯剖面图loaded waterline plane 满载水线图half breadth plan 半宽水线图stowage plan 配载图laying off lofting 放样mold loft floor 放样台mold loft 放样间template 样板mold loft batten, template batten 木样条evolute 展开线allowance 余量assembly 装配subassembly 分段装配subdivision length 分段长度shipbuilding tolerance 造船公差building berth 船台building dock 干坞slip dock 湿坞marine slipway, railway dry dock 船排marine slipway cradle 船排支架building block, stocks 枕木launch 下水launching ways 下水滑道launching grade 下水坡度launching cradle 下水架end launching 纵向下水side way launching 横向下水hydraulic press 水压机flanging machine 折边机plate bending machine 弯板机angle cutter 角钢切断机planing machine 刨边机shearing machine 剪床guillotine shear 龙门剪床oxy-acetylene welding 氧-乙炔焊co2gas welding 二氧化碳气体焊arc welding 电弧焊unionmelt welding 埋弧自动焊fusion welding 熔焊fillet welding 角焊flat seam 对接缝butt joint welding 对接焊intermittent welding 间断焊；断续焊staggered intermittent welding 交错断续焊缝lap weld 搭接焊slot weld 槽焊；长孔焊plug weld 塞焊；圆孔焊run of welding 焊道welding torch 焊炬welding rod 焊条flux 焊药filler metal; deposited metal 熔敷金属welding stress 焊接应力welding procedure 焊接方法welding throat 焊喉cutting torch 割炬acetylene generator 乙炔发生器slag 熔渣undercut （焊接）咬边；根切hydraulic test 水压试验pressure test 压力试验flooding test 灌水试验hose test 冲水试验oil tight test 油密试验purchase trial 交船试验四、船舶性能常用英语第 31 页共 45 页angle of vanishing stability 稳性消失角buoyancy 浮性buoyancy curve 浮力曲线capsizing lever, upsetting lever 倾覆力臂capsizing moment, upsetting moment倾覆力矩center of buoyancy 浮心center of floatation 漂心center of gravity 重心curve of areas of waterplanes 水线面积曲线curve of section areas 横剖面面积曲线curve of volumes of displacement 排水量曲线dynamical stability（curve）动稳性（曲线）entrance angle 进水角floodable length 可浸长度force of buoyancy, buoyant force 浮力free surface 自由液面heaving 垂荡heeling angle 横倾角heeling moment 横倾力矩hogging 中拱hogging condition 中拱状态hogging moment(stress) 中拱力矩（应力）hydrostatic curves 静水力曲线initial metacenter 初稳心initial stability 初稳性insubmersibility 抗沉性longitudinal inclination;第 32 页共 45 页list; heel 纵倾longitudinal stability 纵稳性panting （波浪对船体的）冲击period of rolling 横摇周期pitching 纵摇pounding 波浪冲击maneuverability 操纵性margin line 限界线metacenter 稳心moment to change trim one centimeter 每厘米纵倾力矩permissible length 许可长度potential head 势头pressure head 压头restoring moment, righting moment 复原力矩restoring lever, righting lever 复原力臂rolling 横摇sagging 中垂sagging condition 中垂状态sagging moment(stress) 中垂力矩（应力）seaworthiness 适航性stability 稳性stability at large angles 大倾角稳性stability criterion numeral 稳性横准数static head 静压头（力）statical stability (curve) 静稳性（曲线）surging 纵荡swaying 横荡tons per centimeter of immersion 每厘米吃水吨数total head (pressure) 总压头（力）transverse inclination, trim第 33 页共 45 页纵倾transverse (longitudinal) metacenter 横（纵）稳心transverse (longitudinal) stability 横（纵）稳性trim by the bow (stern) 首（尾）倾turning quality (circle) 回转性（圈）velocity head 速头weigh curve 重力曲线yawing 艏摇五、船体检验常用英语THE DESCRIPTION OF DAMAGEA.General descriptions1.in good condition情况良好2.in poor condition情况欠佳3.in bad condition 情况不佳，情况不良4.in a neglectedcondition 缺乏保养5.not properly serviced未经正常保养6.not properly cleaned未经正常清洁7.not properly protected未经正常保护8.not properly insulated未经正常隔热（或电气绝缘）9.not properly adjusted未经正常校正10.defective 有缺陷的（失效）11.damaged损坏damaged beyondrepair 损坏了无法修复12.failed (in failure)第 34 页共 45 页失效13.cut of order (in trouble)故障out of action 停止工作（作用），不是指故障14.in disorder 零乱（船属具零乱了）15.not working 不能工作16.inoperative 不能工作（失效）unworkable, inoperable 指本身不能工作，在损坏状况判断中不能使用17.out of function 不能工作，失去作用，不起作用18.unserviceable (useless)不能使用（指必须换新的损坏部件）19.could not bestarted(failed to start)不能启动20.empty 空的21.fitted incorrectly安装不正确（指小型的装置设备）installed incorrectly 安装不正确（指较大的装置设备）22.dangerousaccumulation ofinflammable vapors可燃气体危险集积it was obvious that this state had existedfor a considerable time（损坏）状况是长期存在的23.sluggish in (action,answering) （动作、应答）迟钝B.Deficiencies1.no…fitted,no…provided 未第 35 页共 45 页装2.no…available未备有3.missing遗失4.incomplete 不齐全，不完整5.deficient不足，缺少6.insufficient不足7.neglected遗漏8.omitted遗漏，省去9.removed移开，拆走10.washed overboard冲走11.dropped跌落12.fitted with wrong ….(size, material,devices…)错用（尺寸，材料，仪器）C.Tightness, stains, lossof etc.1.Leaking漏2.infiltrating (seeping)渗漏3.weeping泪滴4.sweating汗滴5.not watertight不水密6.loss of watertightness失去水密性（比5好）7.loss of airtightness失去气密性8.loss of oiltightness失去油密性9.escaping of cool逃冷第 36 页共 45 页10.loss of lub-oil pressure滑油压力降低11.loss of water pressure水压力降低12.oil polluted油污染13.oil soaked油浸14.water soaked水浸15.water stained水渍16.oil stained油渍17.rust in patches锈斑18.verdigris in patches铜绿斑19.water marks水渍D.Crack, score, breaketc.1.scuffed 拉毛（仅从反光上可观察到）2.chafed擦痕3.scored 拉痕（痕较chafed深）4.scratched 抓痕（硬拉过的痕）5.scraped 刮痕（长期运行刮的痕）6.grooved 槽痕（比pitting深）7.ridged 凸起雷治痕（环状的痕）8.cracked裂痕hair crack 发痕surface crack 表面裂痕through crack 穿透裂痕non-through crack 未穿透裂痕第 37 页共 45 页9.chapped龟裂，折裂10.fractured折裂11.broken off 破掉（破裂后跌落）broken 破裂，破碎12.holed穿洞13.holed & flooded破洞浸水14.opened开口15.bent弯曲16.canted倾斜17.buckled皱折18.warped翘起，翘曲19.indented (dented)凹痕，凹陷（指船壳板在两档肋位间的凹陷）20.set in 凹陷（指船壳板较大面积的凹陷）21.waved波曲22.curled 卷曲（指绳索）23.rumpled 褶皱（指垫片）24.bulged 鼓起，凸出25.collapsed 倾陷，倾倒26.ruptured毁损27.torn off撕破torn拉脱28.pierced刺破29.peeled 剥皮（油第 38 页共 45 页漆剥落）30.burst 爆破（指高压管路）31.blown off (packing)吹脱32.distorted 扭曲，歪扭33.engine break-down因故障机器突然停车E.Corrosion, seizing,choking etc.1.corrosion腐蚀2.wasted耗油3.deteriorated蚀薄4.thinned变薄5.pitted麻点6.eroded侵蚀7.rusted生锈8.rotten （木、橡胶）腐烂、腐坏9.decayed （电缆）腐烂、腐坏10. aerated（橡胶、电缆）腐烂、腐坏11. aged老化12. seized咬住13. seized by corrosion锈死14. stuck （粘）咬住15. rust-jammed锈轧16. fouled拥塞17. clogged堵塞（常指管子的堵塞）18. blocked第 39 页共 45 页阻塞19. gagged塞口20. foul & dirty闭塞21. blanked封没22. plugged闭塞23. choked 卡住，阻塞F.Wear, loose, clearanceetc.1.Loose松动2.starting（铆钉）松动3.slack松动slack back松出4.worn磨损5.worn cut evenly均匀磨损6.worn cut unevenly不均匀磨损7.worn on one side单边磨损8.worn outsymmetrically 对称磨损9.distorted （轴线弯曲并扭转）扭曲10.sprung（铆钉）扭歪11.twisted （轴线未弯、纯扭转）扭转12.excess clearance间隙过大13.excess backlash齿隙过大14.excess vibration振动过大15.excess noise level噪音过大第 40 页共 45 页16.loose engagement啮合太松17.loose connection接头松动18.tooth齿worn out 磨损chopped off 崩缺fractured折断19.knocking敲击knocking cylinder 敲缸knocking valve gear 伐件敲缸knocking bearing 轴承敲缸20.bearing metal轴承合金detached脱壳cracked开裂wiped铺铅belted熔化oil groove blocked 油槽堵塞21.out off roundness失圆22.out off alignment拉线不直23.off-centering偏心24.deflected偏斜G.Burning, heating, etc.1.Sparking火花2.arcking (arcing)电弧mutator第 41 页共 45 页整流器scored拉痕burnt烧坏worn 磨耗，磨损uneven不平sparking火花blackened发黑rough粗糙mica undercut弧坑4.brush set incorrectly碳刷安装不正确5.scorched烤焦6.coked结焦7.charred结碳8.overheated过热9.broken down击穿10. short-circuit短路11. setting incorrect 整定值不正确12. tripped incorrect脱扣不正常13. batteriescompletely discharged（电）完全发光undercharged未充满overcharged充电过量dry water水干A. Remove, crop etc.1.Removed第 42 页共 45 页拆下2.removed & replaced拆装3.removed, faired &replaced拆装拷平4.cropped & renewed割换（管、板、栏杆）5.partly renewed部分换新6.partly cropped &renewed 部分割换7.cut off割除8.faired拷平9.faired on原地拷平10.faired in place原地拷平11.straightened拷直、校直12.dismantle 拆卸（某一零件）13.disassembled拆散（解体）14.stripped 拆除（某一部件）15.unshipped拆下16.disconnected 断开（线、管接头）17.opened打开18.lifted抬升、举起19.jacked 顶起（用千斤顶顶起）20.replaced (by, with)换用21.patch贴补B.Fit, scrape, grind etc.1.fitted & scraped拂刮2.fitted & ground拂磨第 43 页共 45 页3.scraped & ground刮磨4.made to fit 拂合（装配好）5.run to fit 跑合（运动磨合）6.ground round磨圆7.ground smooth磨光8.ground & reamed磨绞9.bored round镗圆10.planed smooth刨光11.polished抛光12.machined光车13.skimmed光刀14.finish machined精加工15.rough machine粗加工C.Re-metal, adjust,check etc1.Remetalled重浇白合金2.re-babbitted重浇白合金（专指巴氏合金）3.pulled out拉出4.drawn out抽出5.taken out取出6.adjusted调整，校正adjusted for alignment 校正拉线adjusted true 校正拉线adjusted for clearance第 44 页共 45 页校正间隙adjusted for centering 校中adjusted for deflection 校偏7.checked检查checked for roundness 检查圆度checked for insulation resistance 检查绝缘电阻checked for centering检查中心位置checked for alignment 检查拉线checked for clearance 检查间隙8.cleaned清洁9.wire-scrubbed 钢丝刷（除锈）10.chipped & scraped拷锈（油漆）11.measured & recorded测量并记录12.logged (hourly)记录（小时）D.weld, rivet, wind etc.1.repaired by welding电焊修理2.welded补焊、焊接3.closed up by welds（面积、深度、高度较大）焊补4.built up by welds堆焊5.plug welded塞焊6.spot welded点焊7.butt welded对接焊8 tackweld 点焊、平头焊、定位焊第 45 页共 45 页。
船舶常用英语(一)汇总
船舶常用英语(一)汇总一、船舶类型常用英语ship, vessel 船，船舶boat, craft 艇sampan舢板, 小船manpowered boat人力船sailor; sailing boat 帆船motor sailor 机帆船power-driven ship 机动船paddle steamer, paddle wheel vessel 明轮船screw ship; propeller vessel 螺旋桨船airscrew ship; aerial propeller vessel 空气螺旋桨船hovercraft; aircushioncraft 气垫船hydrofoil水翼船hydrojet propelled boat, water jet boat 喷水船steamship; steamer 蒸汽机船motor ship 内燃机船diesel ship 柴油机船electrically-propelledship 电力推进船steam turbine ship 汽轮机船gas turbine ship 燃气轮机船nuclear-power ship核动力船deck ship 甲板船flush deck ship 平甲板船raised quarter-deck shipcargo liner 定期货船tramp ship 不定期货船container ship 集装箱船full-containership 全集装箱船semi-containership 半集装箱船multi-purposecontainer ship 多用途集装箱船general cargo ship/vessel/carrier杂货船bulk (cargo) carrier 散货船ore carrier 矿砂船grain carrier 运粮船coal carrier; coaler 运煤船lumber(timber)carrier运木船cattle carrier 运牲畜船multi-purpose ship多用途船liquid cargo ship 液体货货船chemical tank 化学品液货船liquid chemical tanker 液体化学品船liquefied gas carrier 液化气体船liquefied petroleum gas tanker (LPG) 液化石油气运输船liquefied natural gas tanker (LNG) 液化天然气运输船tanker; oil tanker 油轮super tanker 超级油轮VLCC (very large crude carrier) (吨位在20万至30 万吨之间的) 巨型油轮ULCC (ultra-large crude carrier) (吨位在30万至50万吨之间的) 超巨型油船refrigerated ship; cold storage ship 冷藏船roll-on/roll-off ship(RO/RO ship) 滚装船ferry渡船passenger ferry 旅客渡船freight ferry 货物渡船fishing vessel(boat) 渔轮trawler拖网渔轮barge carrier; lighter aboard ship(LASH)载驳船barge; lighter 驳船deck barge 甲板驳well-deck barge 半舱驳double shell barge 双壳驳single side barge 单舷长大舱口驳oil barge 油驳container barge 集装箱驳船RO/RO barge 滚装驳船liquefied gas barge 液化气体驳hopper barge 开底泥驳split hopper barge 对开泥驳pusher; pushboat 顶推船；推船working ship 工程船tug; tugboat; towboat 拖船harbor tug 港作拖船rescue tug 救助拖轮salvage ship 救捞船dredger挖泥船trailing suction dredge 耙吸挖泥船cutter suction dredger 绞吸挖泥船bucket wheel dredger 斗轮挖泥船bucket dredger链斗挖泥船reclamation craft 吹泥船grab dredger 抓斗挖泥船dipper dredger 铲斗挖泥船floating pitter; drive pitter 打桩船floating crane; derrick boat 起重船floating dock 浮船坞cable layer; cable ship 布缆船scientific surveying ship 科学考察船research ship 科学调查船oceanographic research vessel 海洋调查船surveying ship 测量船ice-breaker破冰船pontoon 浮舟; 浮桥; 趸船, 浮码头high speed craft 高速船passenger catamaran 双体客船vehicle ferry catamaran 双体车辆渡船vehicle-passenger ferry catamaran 双体车客渡船pontoon catamaran 双体趸船二、船舶结构常用英语center line 中心线，中线athwartships 横对船体（与船首尾线直交）bevel斜角；斜面base line 基线amidships 在船中部；在纵中线上designed waterline breadth 设计水线宽designed waterline length 设计水线长draft吃水former/aft draft 首/尾吃水draft figures 吃水尺度intersection 交点；交叉；横断面knuckle折角线length between perpendicular 垂线间长length overall 总长load waterline length 满载水线长register length (breadth;depth) 登记长度（宽度、深度）freeboard干舷rise of floor (dead; rise) 舭高；船底loadlinemark载重水线标记fresh water load line (F.) 淡水载重线fresh water timber load line (L.F.) 淡水木材载重线tropical fresh water load line (TF) 热带淡水载重线tropical load line (T) 热带载重线summer load line(S) 夏季载重线summer freshwater load line(F) 夏季淡水载重线winter load line(W) 冬季载重线winter North Atlantic load line(WNA) 冬季北大西洋载重线even keel （首尾）等吃水，平载extreme breadth 最大宽度floatable length 可浸长度sheer at forward (after) perpendicular 首尾舷弧sheer line 舷弧线accommodation居住舱室accommodation deck 起居舱室；旅客甲板accommodation ladder舷梯accommodation ladder platform 舷梯平台accommodation laddermanrope 舷梯扶索after body 后（部船）体after peak bulkhead 艉尖舱舱壁after peak tank 艉尖舱air hole 空气孔air pipe 空气管appendage （船体水线下的）附体；附件auxiliary machinery 辅助机械；辅机balanced rudder 平衡舵ballast压载（物）ballast line 压载水管系ballast pump 压载水泵ballast pumping system 压载水系统ballast tank(water) 压载舱（水）batten 板条；压条（封仓用）batten-ceiling （货舱内）护舱条，护板beam横梁beam bracket 梁肘板bearding 交合线，榫（艏柱或艉柱上）bending moment 弯矩bilge 舭部；舱底；（船底）污水沟bilge bracket 舭肘板bilge keel(chock, piece) 舭龙骨bilge knee 舭肘板bilge line 舭水管系bilge main 舭水总管bilge pipe (suction) 舭吸水管bilge pump 舭水泵bilge strake(plate) 舭列板bilge well 污水井bitt系缆桩bollard 系缆桩；系船柱；双系柱bolster枕垫bonnet烟囱帽；机罩boom 杆；吊杆；桁；叉架boom crutch(support; rest) 吊杆支架bossing 尾管突出部；轴包套bottom frame 船底横骨bottom longitudinal 船底纵骨bottom plate 船底板bow船首，船头bow fender 艏护垫bow flare 艏部外飘bow thruster 首侧推器第 11 页共 46 页bracket 肘板；（三角）拖架breakwater挡浪板bridge桥；桥楼；驾驶台bulb angle 圆头角材bulbous bow 球形船首，球鼻首bulb stern 球形船尾bulkhead舱壁bulkhead plating 舱壁板bulkhead stiffener 舱壁扶强材bulwark舷墙bulwark plating 舷墙板bulwark stay舷墙扶强材bunker tank 燃料舱bushing衬套butt端接；残片butt joint(seam) 平接缝butt riveting 对接铆butt welding 对接焊butterfly clip 蝴蝶夹bypass valve 旁通阀cable stopper 止链器camber翘曲camber of beam 梁拱第 12 页共 46 页cant beam 斜梁cant bracket 斜角板cant frame 斜肋骨cantilever悬臂梁capstan绞盘；绞缆机cargo batten 货舱护板cargo block 吊货滑车cargo port 装货舷梯，舷门cat walk （油轮上的）天桥，步桥center girder 中底桁center strake 中央内底板chafing plate防擦板chafing ring 防擦环chain lock(well) 锚链舱chain pipe 锚链管chain stopper 止链器chock导缆器；垫木clamp plate 夹板，压板cleat 羊角；系绳铁栓；防滑条coaming围板；舱口围板cofferdam隔离舱collar plate 封板collision bulkhead 船首舱壁；防撞舱壁第 13 页共 46 页companion way(hatch) 升降口corrugated bulkhead 槽形舱壁corrugation皱；槽形；波形cross deck structure 舱间甲板结构crossing strength member 交叉强力构件cruiser stern 巡洋舰型船尾curtain plate 幕板cut out 开口；切davit吊艇架；吊艇柱deck甲板deck beam 甲板横梁deckhouse甲板室deck line 甲板线deck longitudinal 甲板纵骨deck stringer(plate) 甲板边板deep tank 深舱derrick吊杆diaphragm隔板double bottom 双层底doubling plate 双层焊合板drain hole 排水孔duct keel 箱形龙骨dunnage 垫舱（物料）；衬垫第 14 页共 46 页dunnage wood 垫木dynamic load 动载荷end bracket 端肘板escape trunk （船内）应急通道engine bed 机座engine casing 机舱围壁escape scuttle （船内）应急出口escape vent 脱险口expansion joint 伸缩接头expansion trunk(tank) （油船）膨胀深井extension bracket 延伸肘板face plate面板fender碰垫；护舷材fender bar 护舷条fair lead 导缆器flame screen 防焰罩flange折边flanged bracket 折边肘板flat keel 平板龙骨floor肋板folding door 折门forecastle deck 艏楼甲板fore peak tank （船的）首舱；前尖舱第 15 页共 46 页forward perpendicular 首垂线foundation底座frame肋骨frame number 肋骨跨数frame space 肋距freeing port 甲板排水孔；放水孔gangway (gang ladder or gang board) 舷梯gasket 垫圈，垫料（集）密封垫general service pipe (G.S pump) 通用泵，总用泵girder桁材gooseneck(parity iron) 鹅颈头；吊杆弯头grating格子板；滑铁板ground tackle 锚泊索具gunwale舷缘；舷边gunwale angle 舷边角钢gunwale bar 舷边角材gunwale railing 舷边栏杆gunwale tank 舷侧水柜（甲板下）gusset角板；扣板gutter （甲板）水沟；槽沟gutter angle; waterway angle （舷侧）排水沟角钢gypsy 绞筒（锚机绞车上的）第 16 页共 46 页handrail舷墙扶手hanging rudder; hinged rudder 吊舵；悬舵hatch; hatchway; hatch opening 舱口hatch bar 封舱压条hatch batten 舱口边压条hatch beam (web) 舱口大梁hatch booby 活动舱口盖hatch coaming 舱口板hatch cover 舱口盖hatch end beam 舱口端梁hatch moulding 舱口椽材hatch side girder舱口纵桁hatch tarpaulin 盖舱布hatch trunk 舱口围阱hawse pipe 锚链管hawser绳索；大缆heel踵材；横倾hinged cover(door) 铰链盖（门）hold货舱hold beam 舱内梁hold frame 舱内肋骨hold ladder 舱内梯hold stanchion(pillar) 舱内支柱第 17 页共 46 页hold stringer 舱内纵桁hopper漏斗；开舱泥驳hopper tank 底边舱hopper tank sloping plating 底边舱斜板horizontal margin plate 水平内底板horizontal girder 水平桁horizontal stiffener 水平扶强材（防挠材）hull船壳，船体hull construction 船体结构hull plating 船壳板hull strength 船体强度inner bottom 内底inner bottom plating 内底板insert plate 嵌板；衬板jack千斤顶jack ladder 绳梯Jacob's ladder 软梯；绳梯Joggled joint 折接；弯合joggling machine 折曲机keel龙骨keelblock龙骨墩keel line 龙骨线；艏艉线keel plate第 18 页共 46 页龙骨板keel rail （救生艇）艇底把手keelson内龙骨kingpost起重柱；将军柱knee肘板；弯头knee of the deck 甲板梁肘板lightening hole 减轻孔lignum vitae 铁梨木local strength 局部强度local stress 局部应力longitudinal纵骨；纵材；纵桁longitudinal bulkhead 纵舱壁longitudinal bending纵向弯曲longitudinal framing system 纵骨架式longitudinal strength 纵向强度lug耳板main deck 主甲板main frame 主肋骨manhole人孔man hole door 人孔盖man hole coaming 人孔围板moment of inertia 惯性矩margin plate 内底边板molded breadth 型宽第 19 页共 46 页molded depth 型深mooring hole 导缆孔mooring post 系缆柱；岸柱mud box 泥箱non-return valve 止回阀non-watertight bulkhead 非水密舱壁notch 切口；槽口；刻痕oscillating load 振动负荷parallel middle body 平行中体panel stiffener 板格扶强材panting arrangement 防挠振结构panting beam防挠振梁panting stringer 防挠振纵桁pillar支柱；墩pintle舵销plane bulkhead 平面舱壁plane keel 平板龙骨pump room 泵舱helm(rudder) pintle 舵销horizontal margin plate 水平内底边板out bottom plating 外底板platform平台plating壳板第 20 页共 46 页plimsoll mark 载重线标志poop艉楼；船尾poop deck 艉楼甲板port 舷门；舱门；（装货）口；窗；门；孔porthole 舷窗；（装货）舷门propeller; propellor 推进器；螺旋桨propeller aperture 螺旋桨空间propeller boss(bub) 螺旋桨毂propeller shaft 艉轴racking（船体）横向挠度rail扶手；栏杆rolling横摇round of beam 梁拱round stern 圆（船）尾rudder舵rudder carrier 舵托rudder casing 舵杆管rudder pintle 舵针；舵栓rudder plate; rudder blade 舵叶；舵板rudder post 舵柱rudder stock 舵杆rudder trunk 舵杆围壁；舵杆管rung （梯子）踏步；横档scallop扇形开孔scantling构件尺寸scantling of the structure 结构尺寸scarf; scarph 嵌接处；斜面；斜接scarf joint 斜（嵌）接scarf weld （斜面）焊接scarfing bracket 嵌接肘板scupper排水孔scupper pipe 排水管scuttle 舷窗；人孔（盖）；小舱口盖seam焊缝；接缝section剖面section modulus 剖面模数semi-balanced rudder半平衡舵shaft轴shaft bracket 轴架shaft tube; stern tube 艉轴管shaft tunnel(alley; passage;trunk) 轴隧；地轴弄shedder plate 泄板；斜板sheer舷弧；偏航sheer strake 舷顶列板shell船壳；壳shell frame 舷侧肋骨shell plating 船壳板；外板shell strake; outside plating 船体外板shelter deck 遮蔽甲板shifting beam 活动舱口梁shifting board (or plank) 止移板（散装谷类）；防动板side girder 旁桁材side longitudinal 舷侧纵骨side plating 舷侧外板side strake 舷侧列板single bottom 单层底skid护舷木；垫板skylight天窗slanting plate 斜板slop tank 污油水舱sloping plate 斜板sloping plate longitudinal 斜板纵骨slot槽；开缝sluice水密门；水闸sluice valve 闸阀sniped end 削斜端soft toe 软趾solid floor 实肋板sounding pipe测量管；测深管stabilizer减摇装置stabilizing tank 减摇水舱staging 构架；台架；脚手架stanchion支柱；栏杆柱static load 静载荷stay 支柱；撑条；支索stay bar(or rod) 撑杆stay plate 撑板stem艏；艏柱；艏材stem post 艏柱stern船尾，艉部stern counter 船尾突出体stern shaft; propeller shaft 艉轴stern poop 艉楼stern post 尾柱stiffener 防挠材；扶强材；加固物stool托架，座，凳strake列板strength calculation 强度计算strength deck 强力甲板stringer纵桁stringer plate 甲板边板structural member构件structural strength 结构强度strum box （舱底水）过滤箱strut 撑材，支柱，轴架stuffing box 填料箱superstructure上层建筑tail (end) shaft 艉轴tarpaulin 防水油布，帆布，舱盖布thrust bearing(block) 推力轴承thrust shaft collars 推力环tieplate 带板，牵板，连接板topside tank 顶边舱；上边柜topside tank sloping plating 顶边舱斜板torsion扭转torsion strength 扭转强度transom stern 方形船尾transverse横梁，横材transverse bulkhead 横舱壁transverse frame 横肋骨，横框transverse framing system 横骨架式transverse ring 横环transverse strength 横向强度tripping bracket 防倾肘板tween deck 中间甲板tween deck frame 甲板间肋骨twisting distortion 扭转变形twisting moment 扭转力矩tunnel 轴隧，隧道，风筒tunnel escape 轴隧应急出口tunnel shaft bearing 中间轴支撑轴承ullage pipe (port) 油位测定管（孔）ullage space 空挡空间upper deck 上甲板upper (reverse) frame 内底横骨upper (lower) shelf plate上（下）支架板upper (lower) stool 上（下）托架ventilator通风筒vertical ballast trunk 竖向压载通道vertical girder 竖桁warping chocks 滚轮导缆钳wash bulkhead 可荡舱壁，挡水舱壁watertight bulkhead 水密舱壁watertight deck 水密门weather deck 露天甲板web beam 强横梁，桁板横梁web frame 加强肋骨，框架肋骨，桁板肋骨web plate 腹板wedge楔木，楔子winch起货机winch-head绞车卷筒windlass起锚机wing tank 翼舱，翼柜wire clip 钢缆夹wire reel 卷缆车，钢丝滚筒三、船舶材料及工艺常用英语A.Shipbuilding material(造船材料)T-bar T型钢Z-bar Z型钢I-Bar 工字钢channel bar 槽钢angle steel 角钢equal angle steel 等边角钢unequal angle steel 不等边角钢offset bulb plate 球扁钢flat plate 钢板round steel 圆钢half round steel 半圆钢steel pipe 钢管alloy steel 合金钢special steel 特种钢tempering steel 回火钢材low carbon steel 低碳钢high tensile steel 高强度钢copper 紫铜brass 黄铜aluminum alloy 铝合金stainless steel 不锈钢mechanical property 机械性能tensile test 拉伸试验bend test 弯曲试验impact test 冲击试验torsion test 扭转试验torsion strength 抗扭强度torsional deflection 扭转；扭转变形tensile strength 拉伸强度yield strength 屈服强度yield point 屈服点yield stress 屈服应力elastic limit 弹性极限ultimate strength 极限强度ultimate tensile stress 极限拉伸应力elasticity 弹性ductility 延展性，可塑（锻）性flexibility 挠性，柔性，易弯性toughness 韧性brittleness 脆性friability 易碎性hardness 硬度rigidity 刚性，稳定性heat treatment 热处理quench 淬火normalising 正火annealing 退火hardening 硬化，淬火tempering 回火casting 铸件，铸造forging 锻件，锻造pickling 酸洗ship timber 船用木材lignumvitae 铁梨木three-plywood 三夹板asbestos 石棉asbestos cloth 石棉布asbestos board 石棉板asbestos sheet 石棉纸asbestos cord 石棉绳asbestos paint 石棉涂料fiberglass 玻璃丝plastics 塑料resin 树脂rubber 橡皮painting 油漆cladding 镀层，表面处理coating 涂层，敷料corrosion 腐蚀，侵蚀wastage 损耗，蚀耗wear and tear 蚀损，磨损fracture 裂纹fatigue fracture 疲劳裂纹hairline fracture 发式裂纹buckling 皱折deformation 变形deflection, deflexion 挠曲flexion 弯曲lamellar tearing 层间撕裂rust 铁锈scale 锈皮pitting 点蚀，锈斑indent 凹痕，凹陷groove 槽沟detachment 脱开，脱焊rupture 断裂，破裂cropping 割掉renewal 换新descale 除锈grind 磨平be veed out 刨除alignment 对准，校直snip 剪断，剪片taper 削斜，斜度B.Shipbuildingworkmanship （造船工艺）Working drawing 施工图end elevation 后面图front elevation 正面图side elevation 侧面图plane 平面图lines plan 型线图plan of waterlines 水线图general arrangement plan 总布置图construction plan 结构图damage plan 损坏示意图shell expansion plan 外板展开图docking plan 进坞图framing plan 船体构架图inboard profile plan 纵剖面图midship section plan 舯剖面图loaded waterline plane 满载水线图half breadth plan 半宽水线图stowage plan 配载图laying off lofting 放样mold loft floor 放样台mold loft 放样间template 样板mold loft batten, template batten 木样条evolute 展开线allowance 余量assembly 装配subassembly 分段装配subdivision length 分段长度shipbuilding tolerance 造船公差building berth 船台building dock 干坞slip dock 湿坞marine slipway, railway dry dock 船排marine slipway cradle 船排支架building block, stocks 枕木launch 下水launching ways 下水滑道launching grade 下水坡度launching cradle 下水架end launching 纵向下水side way launching 横向下水hydraulic press 水压机flanging machine 折边机plate bending machine 弯板机angle cutter 角钢切断机planing machine 刨边机shearing machine 剪床guillotine shear 龙门剪床oxy-acetylene welding 氧-乙炔焊co2gas welding 二氧化碳气体焊arc welding 电弧焊unionmelt welding 埋弧自动焊fusion welding 熔焊fillet welding 角焊flat seam 对接缝butt joint welding 对接焊intermittent welding 间断焊；断续焊staggered intermittent welding 交错断续焊缝lap weld 搭接焊slot weld 槽焊；长孔焊plug weld 塞焊；圆孔焊run of welding 焊道welding torch 焊炬welding rod 焊条flux 焊药filler metal; deposited metal 熔敷金属welding stress 焊接应力welding procedure 焊接方法welding throat 焊喉cutting torch 割炬acetylene generator 乙炔发生器slag 熔渣undercut （焊接）咬边；根切hydraulic test 水压试验pressure test 压力试验flooding test 灌水试验hose test 冲水试验oil tight test 油密试验purchase trial 交船试验四、船舶性能常用英语angle of vanishing stability 稳性消失角buoyancy 浮性buoyancy curve 浮力曲线capsizing lever, upsetting lever 倾覆力臂capsizing moment, upsetting moment倾覆力矩center of buoyancy 浮心center of floatation 漂心center of gravity 重心curve of areas of waterplanes 水线面积曲线curve of section areas 横剖面面积曲线curve of volumes of displacement 排水量曲线dynamical stability（curve）动稳性（曲线）entrance angle 进水角floodable length 可浸长度force of buoyancy, buoyant force 浮力free surface 自由液面heaving 垂荡heeling angle 横倾角heeling moment 横倾力矩hogging 中拱hogging condition 中拱状态hogging moment(stress) 中拱力矩（应力）hydrostatic curves 静水力曲线initial metacenter 初稳心initial stability 初稳性insubmersibility 抗沉性longitudinal inclination;list; heel 纵倾longitudinal stability 纵稳性panting （波浪对船体的）冲击period of rolling 横摇周期pitching 纵摇pounding 波浪冲击maneuverability 操纵性margin line 限界线metacenter 稳心moment to change trim one centimeter 每厘米纵倾力矩permissible length 许可长度potential head 势头pressure head 压头restoring moment, righting moment 复原力矩restoring lever, righting lever 复原力臂rolling 横摇sagging 中垂sagging condition 中垂状态sagging moment(stress) 中垂力矩（应力）seaworthiness 适航性stability 稳性stability at large angles 大倾角稳性stability criterion numeral 稳性横准数static head 静压头（力）statical stability (curve) 静稳性（曲线）surging 纵荡swaying 横荡tons per centimeter of immersion 每厘米吃水吨数total head (pressure) 总压头（力）transverse inclination, trim 纵倾transverse (longitudinal) metacenter 横（纵）稳心transverse (longitudinal) stability 横（纵）稳性trim by the bow (stern) 首（尾）倾turning quality (circle) 回转性（圈）velocity head 速头weigh curve 重力曲线yawing 艏摇五、船体检验常用英语THE DESCRIPTION OF DAMAGEA.General descriptions1.in good condition情况良好2.in poor condition情况欠佳3.in bad condition 情况不佳，情况不良4.in a neglectedcondition 缺乏保养5.not properly serviced未经正常保养6.not properly cleaned未经正常清洁7.not properly protected未经正常保护8.not properly insulated未经正常隔热（或电气绝缘）9.not properly adjusted未经正常校正10.defective 有缺陷的（失效）11.damaged损坏damaged beyondrepair 损坏了无法修复12.failed (in failure)失效13.cut of order (in trouble)故障out of action 停止工作（作用），不是指故障14.in disorder 零乱（船属具零乱了）15.not working 不能工作16.inoperative 不能工作（失效）unworkable, inoperable 指本身不能工作，在损坏状况判断中不能使用17.out of function 不能工作，失去作用，不起作用18.unserviceable (useless)不能使用（指必须换新的损坏部件）19.could not bestarted(failed to start)不能启动20.empty 空的21.fitted incorrectly安装不正确（指小型的装置设备）installed incorrectly 安装不正确（指较大的装置设备）22.dangerousaccumulation ofinflammable vapors可燃气体危险集积it was obvious that this state had existedfor a considerable time（损坏）状况是长期存在的23.sluggish in (action,answering) （动作、应答）迟钝B.Deficiencies1.no…fitted,no…provided 未装2.no…available未备有3.missing遗失4.incomplete 不齐全，不完整5.deficient不足，缺少6.insufficient不足7.neglected遗漏8.omitted遗漏，省去9.removed移开，拆走10.washed overboard冲走11.dropped跌落12.fitted with wrong ….(size, material,devices…)错用（尺寸，材料，仪器）C.Tightness, stains, lossof etc.1.Leaking漏2.infiltrating (seeping)渗漏3.weeping泪滴4.sweating汗滴5.not watertight不水密6.loss of watertightness失去水密性（比5好）7.loss of airtightness失去气密性8.loss of oiltightness失去油密性9.escaping of cool逃冷10.loss of lub-oil pressure滑油压力降低11.loss of water pressure水压力降低12.oil polluted油污染13.oil soaked油浸14.water soaked水浸15.water stained水渍16.oil stained油渍17.rust in patches锈斑18.verdigris in patches铜绿斑19.water marks水渍D.Crack, score, breaketc.1.scuffed 拉毛（仅从反光上可观察到）2.chafed擦痕3.scored 拉痕（痕较chafed深）4.scratched 抓痕（硬拉过的痕）5.scraped 刮痕（长期运行刮的痕）6.grooved 槽痕（比pitting深）7.ridged 凸起雷治痕（环状的痕）8.cracked裂痕hair crack 发痕surface crack 表面裂痕through crack 穿透裂痕non-through crack 未穿透裂痕9.chapped龟裂，折裂10.fractured折裂11.broken off 破掉（破裂后跌落）broken 破裂，破碎12.holed穿洞13.holed & flooded破洞浸水14.opened开口15.bent弯曲16.canted倾斜17.buckled皱折18.warped翘起，翘曲19.indented (dented)凹痕，凹陷（指船壳板在两档肋位间的凹陷）20.set in 凹陷（指船壳板较大面积的凹陷）21.waved波曲22.curled 卷曲（指绳索）23.rumpled 褶皱（指垫片）24.bulged 鼓起，凸出25.collapsed 倾陷，倾倒26.ruptured毁损27.torn off撕破torn拉脱28.pierced刺破29.peeled 剥皮（油漆剥落）30.burst 爆破（指高压管路）31.blown off (packing)吹脱32.distorted 扭曲，歪扭33.engine break-down因故障机器突然停车E.Corrosion, seizing,choking etc.1.corrosion腐蚀2.wasted耗油3.deteriorated蚀薄4.thinned变薄5.pitted麻点6.eroded侵蚀7.rusted生锈8.rotten （木、橡胶）腐烂、腐坏9.decayed （电缆）腐烂、腐坏10. aerated（橡胶、电缆）腐烂、腐坏11. aged老化12. seized咬住13. seized by corrosion锈死14. stuck （粘）咬住15. rust-jammed锈轧16. fouled拥塞17. clogged堵塞（常指管子的堵塞）18. blocked阻塞19. gagged塞口20. foul & dirty闭塞21. blanked封没22. plugged闭塞23. choked 卡住，阻塞F.Wear, loose, clearanceetc.1.Loose松动2.starting（铆钉）松动3.slack松动slack back松出4.worn磨损5.worn cut evenly均匀磨损6.worn cut unevenly不均匀磨损7.worn on one side单边磨损8.worn outsymmetrically 对称磨损9.distorted （轴线弯曲并扭转）扭曲10.sprung（铆钉）扭歪11.twisted （轴线未弯、纯扭转）扭转12.excess clearance间隙过大13.excess backlash齿隙过大14.excess vibration振动过大15.excess noise level噪音过大16.loose engagement啮合太松17.loose connection接头松动18.tooth齿worn out 磨损chopped off 崩缺fractured折断19.knocking敲击knocking cylinder 敲缸knocking valve gear 伐件敲缸knocking bearing 轴承敲缸20.bearing metal轴承合金detached脱壳cracked开裂wiped铺铅belted熔化oil groove blocked 油槽堵塞21.out off roundness失圆22.out off alignment拉线不直23.off-centering偏心24.deflected偏斜G.Burning, heating, etc.1.Sparking火花2.arcking (arcing)第 41 页共 46 页电弧mutator整流器scored拉痕burnt烧坏worn 磨耗，磨损uneven不平sparking火花blackened发黑rough粗糙mica undercut弧坑4.brush set incorrectly碳刷安装不正确5.scorched烤焦6.coked结焦7.charred结碳8.overheated过热9.broken down击穿10. short-circuit短路11. setting incorrect 整定值不正确12. tripped incorrect脱扣不正常13. batteriescompletely discharged（电）完全发光undercharged未充满overcharged充电过量dry water水干第 42 页共 46 页A. Remove, crop etc.1.Removed拆下2.removed & replaced拆装3.removed, faired &replaced拆装拷平4.cropped & renewed割换（管、板、栏杆）5.partly renewed部分换新6.partly cropped &renewed 部分割换7.cut off割除8.faired拷平9.faired on原地拷平10.faired in place原地拷平11.straightened拷直、校直12.dismantle 拆卸（某一零件）13.disassembled拆散（解体）14.stripped 拆除（某一部件）15.unshipped拆下16.disconnected 断开（线、管接头）17.opened打开18.lifted抬升、举起19.jacked 顶起（用千斤顶顶起）20.replaced (by, with)换用21.patch贴补B.Fit, scrape, grind etc.1.fitted & scraped拂刮第 43 页共 46 页2.fitted & ground拂磨3.scraped & ground刮磨4.made to fit 拂合（装配好）5.run to fit 跑合（运动磨合）6.ground round磨圆7.ground smooth磨光8.ground & reamed磨绞9.bored round镗圆10.planed smooth刨光11.polished抛光12.machined光车13.skimmed光刀14.finish machined精加工15.rough machine粗加工C.Re-metal, adjust,check etc1.Remetalled重浇白合金2.re-babbitted重浇白合金（专指巴氏合金）3.pulled out拉出4.drawn out抽出5.taken out取出6.adjusted调整，校正adjusted for alignment 校正拉线adjusted true第 44 页共 46 页校正拉线adjusted for clearance 校正间隙adjusted for centering 校中adjusted for deflection 校偏7.checked检查checked for roundness 检查圆度checked for insulation resistance 检查绝缘电阻checked for centering检查中心位置checked for alignment 检查拉线checked for clearance 检查间隙8.cleaned清洁9.wire-scrubbed 钢丝刷（除锈）10.chipped & scraped拷锈（油漆）11.measured & recorded测量并记录12.logged (hourly)记录（小时）D.weld, rivet, wind etc.1.repaired by welding电焊修理2.welded补焊、焊接3.closed up by welds（面积、深度、高度较大）焊补4.built up by welds堆焊5.plug welded塞焊6.spot welded点焊7.butt welded对接焊第 45 页共 46 页8 tackweld 点焊、平头焊、定位焊第 46 页共 46 页。
船舶简称
船舶简称各种船型英文缩写（一）按照字母首位顺序排列：1.Bulk Carrier (散货船)其类型分类有：- Handysize (灵便型) ：2~5万吨左右，大灵便型：大于4万吨- Panamax（巴拿马型）: 6~7.5万吨，船的总长小于或等于274.32M，型宽小于或等于32.30M；目前平均载重吨达到8.2万吨- Kmsarmax（卡尔萨姆型）:8~8.9999万吨- Capesize（好望角型）:15万吨左右2.Container（集装箱）（货舱区分：中央部位货舱——集装箱船；其他舱位——普通杂货船可变换区分：货舱内结构可拆装——集装箱船；不可拆装——普通杂货船）3.Oil Tanker（油轮）其类型分类有：- ULCC(巨型原油轮):大于30万吨- VLCC(超大原油轮)：20~30万吨- Suezmax(苏伊士型)：12~16万吨- Aframax(阿芙拉型)：8~12万吨- Panamax(巴拿马型)：6~8万吨各种船型英文缩写（二）按照字母首位顺序排列：BBC:Bulk Carrier 散货船CCOT:Cargo Oil Tanker 货油轮DDFF: 高速渡轮EERRV: 救援船FFLNG: 浮式液化天然气船（科代替岸上传统的液化天然气工厂）FPSO: 浮式生产储油船FPV: 浮式生产设备GG-Cargo Ship: 杂货船LLNG: 液化天然气船LEG: 液化乙烯汽船LPG: 全压式液化石油汽船LSV: 驳运支援船LR成品油轮:stands for large range, 远程成品油轮MMR成品油轮:stands for medium range, 中程成品油轮OOSV:Offshore Support Vessel, 海洋工程船PPSV: 平台供应船PC: 重型石油化学制品运输船PCC:Pure Car Carrier 汽车运输船PCTC:Pure Car & Truck Carrier 大型轿车卡车专用船RRO-RO SHIP: 客滚船Roll-on/Roll-off ship: 滚装船UUCLL: Ultra Large Crude Carrier: 超大型原油轮VVLOC: 大型矿砂船VLCC: 巨型原油轮1、DWTDWT 是DEAD WEIGHT TONNAGE 的缩写，是表示“载重吨”。
船舶常用英语(一)汇总
一、船舶类型常用英语ship, vessel 船，船舶boat, craft 艇sampan 舢板, 小船manpowered boat 人力船sailor; sailing boat 帆船motor sailor 机帆船power-driven ship 机动船paddle steamer, paddle wheel vessel 明轮船screw ship; propeller vessel 螺旋桨船airscrew ship; aerial propeller vessel 空气螺旋桨船hovercraft; aircushion craft 气垫船hydrofoil 水翼船hydrojet propelled boat, water jet boat 喷水船steamship; steamer 蒸汽机船motor ship 内燃机船diesel ship 柴油机船electrically-propelled ship 电力推进船steam turbine ship 汽轮机船gas turbine ship 燃气轮机船nuclear-power ship 核动力船deck ship 甲板船flush deck ship 平甲板船raised quarter-deck ship 尾升高甲板船well-deck ship 半舱船single side ship 单舷长大舱口船three-island ship 三岛式船double shell ship 双壳船riveted ship 铆接船welded ship 焊接船transversely framed ship 横骨架式船longitudinally framed ship 纵骨架式船combined framed ship 混合骨架式船sea-going vessel 海船ocean-going vessel 远洋船coaster 沿海船channel ship 海峡船inland waterway vessel 内河船civil ship; merchant ship 民用船；商船transport ship 运输船pleasure yacht 游艇passenger ship 客船coasting passenger and cargo ship沿海客货船passenger and auto-car carrier 旅客及汽车运输船tourist ship; passenger carrier 旅游船cargo ship; freighter 货船cargo liner 定期货船tramp ship 不定期货船container ship 集装箱船full-container ship 全集装箱船semi-container ship 半集装箱船multi-purpose container ship 多用途集装箱船general cargo ship/vessel/carrier 杂货船bulk (cargo) carrier 散货船ore carrier 矿砂船grain carrier 运粮船coal carrier; coaler 运煤船lumber(timber) carrier 运木船cattle carrier 运牲畜船multi-purpose ship 多用途船liquid cargo ship 液体货货船chemical tank 化学品液货船liquid chemical tanker 液体化学品船liquefied gas carrier 液化气体船liquefied petroleum gas tanker (LPG) 液化石油气运输船liquefied natural gas tanker (LNG) 液化天然气运输船tanker; oil tanker 油轮super tanker 超级油轮VLCC (very large crude carrier) (吨位在20万至30 万吨之间的) 巨型油轮ULCC (ultra-large crude carrier) (吨位在30万至50万吨之间的) 超巨型油船refrigerated ship; cold storage ship 冷藏船roll-on/roll-off ship (RO/RO ship) 滚装船ferry 渡船passenger ferry 旅客渡船freight ferry 货物渡船fishing vessel(boat) 渔轮trawler 拖网渔轮barge carrier; lighter aboard ship(LASH)载驳船barge; lighter 驳船deck barge 甲板驳well-deck barge 半舱驳double shell barge 双壳驳single side barge 单舷长大舱口驳oil barge 油驳container barge 集装箱驳船RO/RO barge 滚装驳船liquefied gas barge 液化气体驳hopper barge 开底泥驳split hopper barge 对开泥驳pusher; pushboat 顶推船；推船working ship 工程船tug; tugboat; towboat 拖船harbor tug 港作拖船rescue tug 救助拖轮salvage ship 救捞船dredger 挖泥船trailing suction dredge 耙吸挖泥船cutter suction dredger 绞吸挖泥船bucket wheel dredger 斗轮挖泥船bucket dredger 链斗挖泥船reclamation craft 吹泥船grab dredger 抓斗挖泥船dipper dredger 铲斗挖泥船floating pitter; drive pitter 打桩船floating crane; derrick boat 起重船floating dock 浮船坞cable layer; cable ship 布缆船scientific surveying ship 科学考察船research ship 科学调查船oceanographic research vessel 海洋调查船surveying ship 测量船ice-breaker 破冰船pontoon 浮舟; 浮桥; 趸船, 浮码头high speed craft 高速船passenger catamaran 双体客船vehicle ferry catamaran 双体车辆渡船vehicle-passenger ferry catamaran 双体车客渡船pontoon catamaran 双体趸船二、船舶结构常用英语center line 中心线，中线athwartships 横对船体（与船首尾线直交）bevel 斜角；斜面base line 基线amidships 在船中部；在纵中线上designed waterline breadth 设计水线宽designed waterline length 设计水线长draft 吃水former/aft draft 首/尾吃水draft figures 吃水尺度intersection 交点；交叉；横断面knuckle 折角线length between perpendicular 垂线间长length overall 总长load waterline length 满载水线长register length (breadth; depth) 登记长度（宽度、深度）freeboard 干舷rise of floor (dead; rise) 舭高；船底loadline mark 载重水线标记fresh water load line (F.) 淡水载重线fresh water timber load line (L.F.) 淡水木材载重线tropical fresh water load line (TF) 热带淡水载重线tropical load line (T) 热带载重线summer load line(S) 夏季载重线summer freshwater load line(F) 夏季淡水载重线winter load line(W) 冬季载重线winter North Atlantic load line(WNA) 冬季北大西洋载重线even keel （首尾）等吃水，平载extreme breadth 最大宽度floatable length 可浸长度sheer at forward (after) perpendicular 首尾舷弧sheer line 舷弧线accommodation 居住舱室accommodation deck 起居舱室；旅客甲板accommodation ladder 舷梯accommodation ladder platform 舷梯平台accommodation ladder manrope 舷梯扶索after body 后（部船）体after peak bulkhead 艉尖舱舱壁after peak tank 艉尖舱air hole 空气孔air pipe 空气管appendage （船体水线下的）附体；附件auxiliary machinery 辅助机械；辅机balanced rudder 平衡舵ballast 压载（物）ballast line 压载水管系ballast pump 压载水泵ballast pumping system 压载水系统ballast tank(water) 压载舱（水）batten 板条；压条（封仓用）batten-ceiling （货舱内）护舱条，护板beam 横梁beam bracket 梁肘板bearding 交合线，榫（艏柱或艉柱上）bending moment 弯矩bilge 舭部；舱底；（船底）污水沟bilge bracket 舭肘板bilge keel(chock, piece) 舭龙骨bilge knee 舭肘板bilge line 舭水管系bilge main 舭水总管bilge pipe (suction) 舭吸水管bilge pump 舭水泵bilge strake(plate) 舭列板bilge well 污水井bitt 系缆桩bollard 系缆桩；系船柱；双系柱bolster 枕垫bonnet 烟囱帽；机罩boom 杆；吊杆；桁；叉架boom crutch(support; rest) 吊杆支架bossing 尾管突出部；轴包套bottom frame 船底横骨bottom longitudinal 船底纵骨bottom plate 船底板bow 船首，船头bow fender 艏护垫bow flare 艏部外飘bow thruster 首侧推器bracket 肘板；（三角）拖架breakwater 挡浪板bridge 桥；桥楼；驾驶台bulb angle 圆头角材bulbous bow 球形船首，球鼻首bulb stern 球形船尾bulkhead 舱壁bulkhead plating 舱壁板bulkhead stiffener 舱壁扶强材bulwark 舷墙bulwark plating 舷墙板bulwark stay 舷墙扶强材bunker tank 燃料舱bushing 衬套butt 端接；残片butt joint(seam) 平接缝butt riveting 对接铆butt welding 对接焊butterfly clip 蝴蝶夹bypass valve 旁通阀cable stopper 止链器camber 翘曲camber of beam 梁拱cant beam 斜梁cant bracket 斜角板cant frame 斜肋骨cantilever 悬臂梁capstan 绞盘；绞缆机cargo batten 货舱护板cargo block 吊货滑车cargo port 装货舷梯，舷门cat walk （油轮上的）天桥，步桥center girder 中底桁center strake 中央内底板chafing plate 防擦板chafing ring 防擦环chain lock(well) 锚链舱chain pipe 锚链管chain stopper 止链器chock 导缆器；垫木clamp plate 夹板，压板cleat 羊角；系绳铁栓；防滑条coaming 围板；舱口围板cofferdam 隔离舱collar plate 封板collision bulkhead 船首舱壁；防撞舱壁companion way(hatch) 升降口corrugated bulkhead 槽形舱壁corrugation 皱；槽形；波形cross deck structure 舱间甲板结构crossing strength member 交叉强力构件cruiser stern 巡洋舰型船尾curtain plate 幕板cut out 开口；切davit 吊艇架；吊艇柱deck 甲板deck beam 甲板横梁deckhouse 甲板室deck line 甲板线deck longitudinal 甲板纵骨deck stringer(plate) 甲板边板deep tank 深舱derrick 吊杆diaphragm 隔板double bottom 双层底doubling plate 双层焊合板drain hole 排水孔duct keel 箱形龙骨dunnage 垫舱（物料）；衬垫dunnage wood 垫木dynamic load 动载荷end bracket 端肘板escape trunk （船内）应急通道engine bed 机座engine casing 机舱围壁escape scuttle （船内）应急出口escape vent 脱险口expansion joint 伸缩接头expansion trunk(tank) （油船）膨胀深井extension bracket 延伸肘板face plate 面板fender 碰垫；护舷材fender bar 护舷条fair lead 导缆器flame screen 防焰罩flange 折边flanged bracket 折边肘板flat keel 平板龙骨floor 肋板folding door 折门forecastle deck 艏楼甲板fore peak tank （船的）首舱；前尖舱forward perpendicular 首垂线foundation 底座frame 肋骨frame number 肋骨跨数frame space 肋距freeing port 甲板排水孔；放水孔gangway (gang ladder or gang board) 舷梯gasket 垫圈，垫料（集）密封垫general service pipe (G.S pump) 通用泵，总用泵girder 桁材gooseneck(parity iron) 鹅颈头；吊杆弯头grating 格子板；滑铁板ground tackle 锚泊索具gunwale 舷缘；舷边gunwale angle 舷边角钢gunwale bar 舷边角材gunwale railing 舷边栏杆gunwale tank 舷侧水柜（甲板下）gusset 角板；扣板gutter （甲板）水沟；槽沟gutter angle; waterway angle （舷侧）排水沟角钢gypsy 绞筒（锚机绞车上的）handrail 舷墙扶手hanging rudder; hinged rudder 吊舵；悬舵hatch; hatchway; hatch opening 舱口hatch bar 封舱压条hatch batten 舱口边压条hatch beam (web) 舱口大梁hatch booby 活动舱口盖hatch coaming 舱口板hatch cover 舱口盖hatch end beam 舱口端梁hatch moulding 舱口椽材hatch side girder 舱口纵桁hatch tarpaulin 盖舱布hatch trunk 舱口围阱hawse pipe 锚链管hawser 绳索；大缆heel 踵材；横倾hinged cover(door) 铰链盖（门）hold 货舱hold beam 舱内梁hold frame 舱内肋骨hold ladder 舱内梯hold stanchion(pillar) 舱内支柱hold stringer 舱内纵桁hopper 漏斗；开舱泥驳hopper tank 底边舱hopper tank sloping plating 底边舱斜板horizontal margin plate 水平内底板horizontal girder 水平桁horizontal stiffener 水平扶强材（防挠材）hull 船壳，船体hull construction 船体结构hull plating 船壳板hull strength 船体强度inner bottom 内底inner bottom plating 内底板insert plate 嵌板；衬板jack 千斤顶jack ladder 绳梯Jacob's ladder 软梯；绳梯Joggled joint 折接；弯合joggling machine 折曲机keel 龙骨keelblock 龙骨墩keel line 龙骨线；艏艉线keel plate 龙骨板keel rail （救生艇）艇底把手keelson 内龙骨kingpost 起重柱；将军柱knee 肘板；弯头knee of the deck 甲板梁肘板lightening hole 减轻孔lignum vitae 铁梨木local strength 局部强度local stress 局部应力longitudinal 纵骨；纵材；纵桁longitudinal bulkhead 纵舱壁longitudinal bending 纵向弯曲longitudinal framing system 纵骨架式longitudinal strength 纵向强度lug 耳板main deck 主甲板main frame 主肋骨manhole 人孔man hole door 人孔盖man hole coaming 人孔围板moment of inertia 惯性矩margin plate 内底边板molded breadth 型宽molded depth 型深mooring hole 导缆孔mooring post 系缆柱；岸柱mud box 泥箱non-return valve 止回阀non-watertight bulkhead 非水密舱壁notch 切口；槽口；刻痕oscillating load 振动负荷parallel middle body 平行中体panel stiffener 板格扶强材panting arrangement 防挠振结构panting beam 防挠振梁panting stringer 防挠振纵桁pillar 支柱；墩pintle 舵销plane bulkhead 平面舱壁plane keel 平板龙骨pump room 泵舱helm(rudder) pintle 舵销horizontal margin plate 水平内底边板out bottom plating 外底板platform 平台plating 壳板plimsoll mark 载重线标志poop 艉楼；船尾poop deck 艉楼甲板port 舷门；舱门；（装货）口；窗；门；孔porthole 舷窗；（装货）舷门propeller; propellor 推进器；螺旋桨propeller aperture 螺旋桨空间propeller boss(bub) 螺旋桨毂propeller shaft 艉轴racking （船体）横向挠度rail 扶手；栏杆rolling 横摇round of beam 梁拱round stern 圆（船）尾rudder 舵rudder carrier 舵托rudder casing 舵杆管rudder pintle 舵针；舵栓rudder plate; rudder blade 舵叶；舵板rudder post 舵柱rudder stock 舵杆rudder trunk 舵杆围壁；舵杆管rung （梯子）踏步；横档scallop 扇形开孔scantling 构件尺寸scantling of the structure 结构尺寸scarf; scarph 嵌接处；斜面；斜接scarf joint 斜（嵌）接scarf weld （斜面）焊接scarfing bracket 嵌接肘板scupper 排水孔scupper pipe 排水管scuttle 舷窗；人孔（盖）；小舱口盖seam 焊缝；接缝section 剖面section modulus 剖面模数semi-balanced rudder 半平衡舵shaft 轴shaft bracket 轴架shaft tube; stern tube 艉轴管shaft tunnel(alley; passage; trunk) 轴隧；地轴弄shedder plate 泄板；斜板sheer 舷弧；偏航sheer strake 舷顶列板shell 船壳；壳shell frame 舷侧肋骨shell plating 船壳板；外板shell strake; outside plating 船体外板shelter deck 遮蔽甲板shifting beam 活动舱口梁shifting board (or plank) 止移板（散装谷类）；防动板side girder 旁桁材side longitudinal 舷侧纵骨side plating 舷侧外板side strake 舷侧列板single bottom 单层底skid 护舷木；垫板skylight 天窗slanting plate 斜板slop tank 污油水舱sloping plate 斜板sloping plate longitudinal 斜板纵骨slot 槽；开缝sluice 水密门；水闸sluice valve 闸阀sniped end 削斜端soft toe 软趾solid floor 实肋板sounding pipe 测量管；测深管stabilizer 减摇装置stabilizing tank 减摇水舱staging 构架；台架；脚手架stanchion 支柱；栏杆柱static load 静载荷stay 支柱；撑条；支索stay bar(or rod) 撑杆stay plate 撑板stem 艏；艏柱；艏材stem post 艏柱stern 船尾，艉部stern counter 船尾突出体stern shaft; propeller shaft 艉轴stern poop 艉楼stern post 尾柱stiffener 防挠材；扶强材；加固物stool 托架，座，凳strake 列板strength calculation 强度计算strength deck 强力甲板stringer 纵桁stringer plate 甲板边板structural member 构件structural strength 结构强度strum box （舱底水）过滤箱strut 撑材，支柱，轴架stuffing box 填料箱superstructure 上层建筑tail (end) shaft 艉轴tarpaulin 防水油布，帆布，舱盖布thrust bearing(block) 推力轴承thrust shaft collars 推力环tieplate 带板，牵板，连接板topside tank 顶边舱；上边柜topside tank sloping plating 顶边舱斜板torsion 扭转torsion strength 扭转强度transom stern 方形船尾transverse 横梁，横材transverse bulkhead 横舱壁transverse frame 横肋骨，横框transverse framing system 横骨架式transverse ring 横环transverse strength 横向强度tripping bracket 防倾肘板tween deck 中间甲板tween deck frame 甲板间肋骨twisting distortion 扭转变形twisting moment 扭转力矩tunnel 轴隧，隧道，风筒tunnel escape 轴隧应急出口tunnel shaft bearing 中间轴支撑轴承ullage pipe (port) 油位测定管（孔）ullage space 空挡空间upper deck 上甲板upper (reverse) frame 内底横骨upper (lower) shelf plate 上（下）支架板upper (lower) stool 上（下）托架ventilator 通风筒vertical ballast trunk 竖向压载通道vertical girder 竖桁warping chocks 滚轮导缆钳wash bulkhead 可荡舱壁，挡水舱壁watertight bulkhead 水密舱壁watertight deck 水密门weather deck 露天甲板web beam 强横梁，桁板横梁web frame 加强肋骨，框架肋骨，桁板肋骨web plate 腹板wedge 楔木，楔子winch 起货机winch-head 绞车卷筒windlass 起锚机wing tank 翼舱，翼柜wire clip 钢缆夹wire reel 卷缆车，钢丝滚筒三、船舶材料及工艺常用英语A.Shipbuilding material (造船材料)T-bar T型钢Z-bar Z型钢I-B ar 工字钢channel bar 槽钢angle steel 角钢equal angle steel 等边角钢unequal angle steel 不等边角钢offset bulb plate 球扁钢flat plate 钢板round steel 圆钢half round steel 半圆钢steel pipe 钢管alloy steel 合金钢special steel 特种钢tempering steel 回火钢材low carbon steel 低碳钢high tensile steel 高强度钢copper 紫铜brass 黄铜aluminum alloy 铝合金stainless steel 不锈钢mechanical property 机械性能tensile test 拉伸试验bend test 弯曲试验impact test 冲击试验torsion test 扭转试验torsion strength 抗扭强度torsional deflection 扭转；扭转变形tensile strength 拉伸强度yield strength 屈服强度yield point 屈服点yield stress 屈服应力elastic limit 弹性极限ultimate strength 极限强度ultimate tensile stress 极限拉伸应力elasticity 弹性ductility 延展性，可塑（锻）性flexibility 挠性，柔性，易弯性toughness 韧性brittleness 脆性friability 易碎性hardness 硬度rigidity 刚性，稳定性heat treatment 热处理quench 淬火normalising 正火annealing 退火hardening 硬化，淬火tempering 回火casting 铸件，铸造forging 锻件，锻造pickling 酸洗ship timber 船用木材lignumvitae 铁梨木three-plywood 三夹板asbestos 石棉asbestos cloth 石棉布asbestos board 石棉板asbestos sheet 石棉纸asbestos cord 石棉绳asbestos paint 石棉涂料fiberglass 玻璃丝plastics 塑料resin 树脂rubber 橡皮painting 油漆cladding 镀层，表面处理coating 涂层，敷料corrosion 腐蚀，侵蚀wastage 损耗，蚀耗wear and tear 蚀损，磨损fracture 裂纹fatigue fracture 疲劳裂纹hairline fracture 发式裂纹buckling 皱折deformation 变形deflection, deflexion 挠曲flexion 弯曲lamellar tearing 层间撕裂rust 铁锈scale 锈皮pitting 点蚀，锈斑indent 凹痕，凹陷groove 槽沟detachment 脱开，脱焊rupture 断裂，破裂cropping 割掉renewal 换新descale 除锈grind 磨平be veed out 刨除alignment 对准，校直snip 剪断，剪片taper 削斜，斜度B.Shipbuilding workmanship （造船工艺）Working drawing 施工图end elevation 后面图front elevation 正面图side elevation 侧面图plane 平面图lines plan 型线图plan of waterlines 水线图general arrangement plan 总布置图construction plan 结构图damage plan 损坏示意图shell expansion plan 外板展开图docking plan 进坞图framing plan 船体构架图inboard pro 纵剖面图midship section plan 舯剖面图loaded waterline plane 满载水线图half breadth plan 半宽水线图stowage plan 配载图laying off lofting 放样mold loft floor 放样台mold loft 放样间template 样板mold loft batten, template batten 木样条evolute 展开线allowance 余量assembly 装配subassembly 分段装配subdivision length 分段长度shipbuilding tolerance 造船公差building berth 船台building dock 干坞slip dock 湿坞marine slipway, railway dry dock 船排marine slipway cradle 船排支架building block, stocks 枕木launch 下水launching ways 下水滑道launching grade 下水坡度launching cradle 下水架end launching 纵向下水side way launching 横向下水hydraulic press 水压机flanging machine 折边机plate bending machine 弯板机angle cutter 角钢切断机planing machine 刨边机shearing machine 剪床guillotine shear 龙门剪床oxy-acetylene welding 氧-乙炔焊co2 gas welding 二氧化碳气体焊arc welding 电弧焊unionmelt welding 埋弧自动焊fusion welding 熔焊fillet welding 角焊flat seam 对接缝butt joint welding 对接焊intermittent welding 间断焊；断续焊staggered intermittent welding 交错断续焊缝lap weld 搭接焊slot weld 槽焊；长孔焊plug weld 塞焊；圆孔焊run of welding 焊道welding torch 焊炬welding rod 焊条flux 焊药filler metal; deposited metal 熔敷金属welding stress 焊接应力welding procedure 焊接方法welding throat 焊喉cutting torch 割炬acetylene generator 乙炔发生器slag 熔渣undercut （焊接）咬边；根切hydraulic test 水压试验pressure test 压力试验flooding test 灌水试验hose test 冲水试验oil tight test 油密试验purchase trial 交船试验四、船舶性能常用英语angle of vanishing stability 稳性消失角buoyancy 浮性buoyancy curve 浮力曲线capsizing lever, upsetting lever 倾覆力臂capsizing moment, upsetting moment 倾覆力矩center of buoyancy 浮心center of floatation 漂心center of gravity 重心curve of areas of waterplanes 水线面积曲线curve of section areas 横剖面面积曲线curve of volumes of displacement 排水量曲线dynamical stability（curve）动稳性（曲线）entrance angle 进水角floodable length 可浸长度force of buoyancy, buoyant force 浮力free surface 自由液面heaving 垂荡heeling angle 横倾角heeling moment 横倾力矩hogging 中拱hogging condition 中拱状态hogging moment(stress) 中拱力矩（应力）hydrostatic curves 静水力曲线initial metacenter 初稳心initial stability 初稳性insubmersibility 抗沉性longitudinal inclination; list; heel 纵倾longitudinal stability 纵稳性panting （波浪对船体的）冲击period of rolling 横摇周期pitching 纵摇pounding 波浪冲击maneuverability 操纵性margin line 限界线metacenter 稳心moment to change trim one centimeter 每厘米纵倾力矩permissible length 许可长度potential head 势头pressure head 压头restoring moment, righting moment 复原力矩restoring lever, righting lever 复原力臂rolling 横摇sagging 中垂sagging condition 中垂状态sagging moment(stress) 中垂力矩（应力）seaworthiness 适航性stability 稳性stability at large angles 大倾角稳性stability criterion numeral 稳性横准数static head 静压头（力）statical stability (curve) 静稳性（曲线）surging 纵荡swaying 横荡tons per centimeter of immersion 每厘米吃水吨数total head (pressure) 总压头（力）transverse inclination, trim 纵倾transverse (longitudinal) metacenter 横（纵）稳心transverse (longitudinal) stability 横（纵）稳性trim by the bow (stern) 首（尾）倾turning quality (circle) 回转性（圈）velocity head 速头weigh curve 重力曲线yawing 艏摇五、船体检验常用英语THE DESCRIPTION OF DAMAGEA.General descriptions1.in good condition 情况良好2.in poor condition 情况欠佳3.in bad condition 情况不佳，情况不良4.in a neglected condition 缺乏保养5.not properly serviced 未经正常保养6.not properly cleaned 未经正常清洁7.not properly protected未经正常保护8.not properly insulated未经正常隔热（或电气绝缘）9.not properly adjusted 未经正常校正10.defective 有缺陷的（失效）11.damaged 损坏damaged beyond repair 损坏了无法修复12.failed (in failure) 失效13.cut of order (in trouble) 故障out of action 停止工作（作用），不是指故障14.in disorder 零乱（船属具零乱了）15.not working 不能工作16.inoperative 不能工作（失效）unworkable, inoperable 指本身不能工作，在损坏状况判断中不能使用17.out of function 不能工作，失去作用，不起作用18.unserviceable (useless) 不能使用（指必须换新的损坏部件）19.could not be started(failed to start) 不能启动20.empty 空的21.fitted incorrectly 安装不正确（指小型的装置设备）installed incorrectly 安装不正确（指较大的装置设备）22.dangerous accumulation of inflammablevapors 可燃气体危险集积it was obvious that this state had existed for a considerable time （损坏）状况是长期存在的23.sluggish in (action, answering) （动作、应答）迟钝B.Deficiencies1.no…fitted, no…provided 未装2.no…available未备有3.missing 遗失4.incomplete 不齐全，不完整5.deficient 不足，缺少6.insufficient 不足7.neglected 遗漏8.omitted 遗漏，省去9.removed 移开，拆走10.washed overboard 冲走11.dropped 跌落12.fitted with wrong ….(size, material, devices…)错用（尺寸，材料，仪器）C.Tightness, stains, loss of etc.1.Leaking 漏2.infiltrating (seeping) 渗漏3.weeping 泪滴4.sweating 汗滴5.not watertight 不水密6.loss of watertightness 失去水密性（比5好）7.loss of airtightness 失去气密性8.loss of oiltightness 失去油密性9.escaping of cool 逃冷10.loss of lub-oil pressure 滑油压力降低11.loss of water pressure 水压力降低12.oil polluted 油污染13.oil soaked 油浸14.water soaked 水浸15.water stained 水渍16.oil stained 油渍17.rust in patches 锈斑18.verdigris in patches 铜绿斑19.water marks 水渍D.Crack, score, break etc.1.scuffed 拉毛（仅从反光上可观察到）2.chafed 擦痕3.scored 拉痕（痕较chafed深）4.scratched 抓痕（硬拉过的痕）5.scraped 刮痕（长期运行刮的痕）6.grooved 槽痕（比pitting深）7.ridged 凸起雷治痕（环状的痕）8.cracked 裂痕hair crack 发痕surface crack 表面裂痕through crack 穿透裂痕non-through crack 未穿透裂痕9.chapped 龟裂，折裂10.fractured 折裂11.broken off 破掉（破裂后跌落）broken 破裂，破碎12.holed 穿洞13.holed & flooded 破洞浸水14.opened 开口15.bent 弯曲16.canted 倾斜17.buckled 皱折18.warped 翘起，翘曲19.indented (dented) 凹痕，凹陷（指船壳板在两档肋位间的凹陷）20.set in 凹陷（指船壳板较大面积的凹陷）21.waved 波曲22.curled 卷曲（指绳索）23.rumpled 褶皱（指垫片）24.bulged 鼓起，凸出25.collapsed 倾陷，倾倒26.ruptured 毁损27.torn off 撕破torn 拉脱28.pierced 刺破29.peeled 剥皮（油漆剥落）30.burst 爆破（指高压管路）31.blown off (packing) 吹脱32.distorted 扭曲，歪扭33.engine break-down 因故障机器突然停车E.Corrosion, seizing, choking etc.1.corrosion 腐蚀2.wasted 耗油3.deteriorated 蚀薄4.thinned 变薄5.pitted 麻点6.eroded 侵蚀7.rusted 生锈8.rotten （木、橡胶）腐烂、腐坏9.decayed （电缆）腐烂、腐坏10. aerated（橡胶、电缆）腐烂、腐坏11. aged 老化12. seized 咬住13. seized by corrosion 锈死14. stuck （粘）咬住15. rust-jammed 锈轧16. fouled 拥塞17. clogged堵塞（常指管子的堵塞）18. blocked 阻塞19. gagged 塞口20. foul & dirty 闭塞21. blanked 封没22. plugged 闭塞23. choked 卡住，阻塞F.Wear, loose, clearance etc.1.Loose 松动2.starting （铆钉）松动3.slack 松动slack back 松出4.worn 磨损5.worn cut evenly 均匀磨损6.worn cut unevenly 不均匀磨损7.worn on one side 单边磨损8.worn out symmetrically 对称磨损9.distorted （轴线弯曲并扭转）扭曲10.sprung （铆钉）扭歪11.twisted （轴线未弯、纯扭转）扭转12.excess clearance 间隙过大13.excess backlash 齿隙过大14.excess vibration 振动过大15.excess noise level 噪音过大16.loose engagement 啮合太松17.loose connection 接头松动18.tooth 齿worn out 磨损chopped off 崩缺fractured 折断19.knocking 敲击knocking cylinder 敲缸knocking valve gear 伐件敲缸knocking bearing 轴承敲缸20.bearing metal 轴承合金detached 脱壳cracked 开裂wiped 铺铅belted 熔化oil groove blocked 油槽堵塞21.out off roundness 失圆22.out off alignment 拉线不直23.off-centering 偏心24.deflected 偏斜G.Burning, heating, etc.1.Sparking 火花2.arcking (arcing) 电弧mutator 整流器scored 拉痕burnt 烧坏worn 磨耗，磨损uneven 不平sparking 火花blackened 发黑rough 粗糙mica undercut 弧坑4.brush set incorrectly 碳刷安装不正确5.scorched 烤焦6.coked 结焦7.charred 结碳8.overheated 过热9.broken down 击穿10. short-circuit 短路11. setting incorrect 整定值不正确12. tripped incorrect 脱扣不正常13. batteriescompletely discharged（电）完全发光undercharged 未充满overcharged 充电过量dry water 水干A. Remove, crop etc.1.Removed 拆下2.removed & replaced 拆装3.removed, faired & replaced拆装拷平4.cropped & renewed 割换（管、板、栏杆）5.partly renewed 部分换新6.partly cropped & renewed 部分割换7.cut off 割除8.faired 拷平9.faired on 原地拷平10.faired in place 原地拷平11.straightened 拷直、校直12.dismantle 拆卸（某一零件）13.disassembled 拆散（解体）14.stripped 拆除（某一部件）15.unshipped 拆下16.disconnected 断开（线、管接头）17.opened 打开18.lifted 抬升、举起19.jacked 顶起（用千斤顶顶起）20.replaced (by, with) 换用21.patch 贴补B.Fit, scrape, grind etc.1.fitted & scraped 拂刮2.fitted & ground 拂磨3.scraped & ground 刮磨4.made to fit 拂合（装配好）5.run to fit 跑合（运动磨合）6.ground round 磨圆7.ground smooth 磨光8.ground & reamed 磨绞9.bored round 镗圆10.planed smooth 刨光11.polished 抛光12.machined 光车13.skimmed 光刀14.finish machined 精加工15.rough machine 粗加工C.Re-metal, adjust, check etc1.Remetalled 重浇白合金2.re-babbitted 重浇白合金（专指巴氏合金）3.pulled out 拉出4.drawn out 抽出5.taken out 取出6.adjusted 调整，校正adjusted for alignment 校正拉线adjusted true 校正拉线adjusted for clearance 校正间隙adjusted for centering 校中adjusted for deflection 校偏7.checked 检查checked for roundness 检查圆度checked for insulation resistance 检查绝缘电阻checked for centering检查中心位置checked for alignment 检查拉线checked for clearance 检查间隙8.cleaned 清洁9.wire-scrubbed 钢丝刷（除锈）10.chipped & scraped 拷锈（油漆）11.measured & recorded 测量并记录12.logged (hourly) 记录（小时）D.weld, rivet, wind etc.1.r epaired by welding 电焊修理2.w elded 补焊、焊接3.c losed up by welds （面积、深度、高度较大）焊补4.b uilt up by welds 堆焊5.p lug welded 塞焊6.s pot welded 点焊7.b utt welded 对接焊8 tackweld 点焊、平头焊、定位焊。
船舶缩略语
HULL(船体):ABS (American Bureau of Standard)美国船级社ANG (Angle Bar)角钢BFE (Builder Furnish Equipment)建造商提供设备BG (Bulk Carrier)散货船BHD (Bulkhead)舱壁BHP (Break Horsepower)制动马力BL (Base Line)基线BM (Breadth Molded)型宽BV (Bureau Veritas)法国船级社CAD (Computer Aided Design)计算机辅助设计CAM (Computer Aided Manufacturing)计算机辅助制造CB (Center of Buoyancy)浮心CCS (China Classification Society)中国船级社CF (Center of Floatation)漂心CFE (Contractor Furnish Equipment)承包商提供设备CG (Center of Gravity)重心CH (Channel)槽钢CM (Metacenter)稳心CPP (The Controllable Pitch Propeller)可调螺距桨CS (Carbon Steel)碳素钢DB (Double Bottom)双层底DK (Deck)甲板DM (Depth Molded)型深DNV (Det Norske Veritas)挪威船级社DWG (Drawing)图DWL (Design Waterline)设计水线DWT (Deadweight)载重量FAT (Factory Acceptance Test)工厂验收试验FB (Flat Bar)扁钢FEM (Finite Element Method)有限元法FPSO (Floating Production Storage Offloading) 浮（船）式生产储油卸油系统FSO (Floating Storage Offloading)浮（船）式储油卸油系统Fwd (Forward)向船艏GL (Germanischer Lloyd)德国船级社GM (Metacentric Height)初稳心高HP (Half Bulb Plate)球扁钢LBP (Length between Perpendiculars)垂线间长LCG (Longitudinal Center of Gravity)纵向重心LNG (Liquefied Natural Gas Vessel) 液化石油气船LOA (Overall Length)总长Long. (Longitudinal)纵骨LPG (Liquefied Petroleum Gas Vessel) 液化天然气船LR (Lloyd's Register)英国劳氏船级社MDK (Main Deck)主甲板MODU (Mobile Offshore Drilling Units)移动式近海钻井平台MS (Mild Steel)低碳钢MTO (Material Takeoff)材料估算NK (Nippon Kaiji Kyokai)日本海事协会OFE (Owner Furnished Equipment)船东提供设备OT (Oil Tight)油密PL (Plate)板RI (Register Italian)意大利船级社SB (Starboard)右舷Semi- (Semi-submersible Platform)半潜式钻井平台STLP (Suspended Tension Leg Platform)悬式张力腿平台TCG (Transverse Center of Gravity)横向重心TEU (Twenty-foot equivalent Unit)20英尺国际标准集装箱TLP (Tension Leg Platform)张力腿平台UCLL (Ultra Large Crude Carrier)超大型油船VCG (Vertical Center of Gravity)垂向重心VLCC (Very Large Crude Carrier)特大型油船WB (Web Bar)腹板WL (Waterline)水线WT (Water Tight)水密MECHANICAL & PIPING（轮机）：AHU (Air Handling Unit)通风装置BHP (Break Horsepower)制动马力A/C (Air Compressor)空气压缩机A/C (Air Conditioning)空调BB (Ball Bearing)滚珠轴承BRG (Bearing)轴承CAS NUT(Castle Nut)蝶型螺帽CCR (Central Control Room)中心控制室COW (Crude Oil Washing)原油洗舱DFO (Diesel Fuel Oil)柴油DPS (Dynamic Position System)动力定位系统DT (Double-Thread)双头螺纹FS (Forged Steel)锻钢FW (Fresh Water)淡水FO (Fuel Oil)燃油GRP (Glass-reinforced Plastic)玻璃钢HVAV (Heating Ventilation and Air-condition)暖通空调系统HPU (Hydraulic Power Unit)液压工作站LSA (Life Saving Apparatus)救生器具LCC (Local Control Console)机旁控制台LO (Lube Oil)滑油MDO (Marine Diesel Oil)船用柴油OS (Operation System)操作系统PLC (Programmable Logic Controller)逻辑控制单元PMS (Power Manage System)动力管理系统ELECTRICAL（电气）:AC (Alternative Current)交流电AVR (Automatic Voltage Regulation)自动电压调整计CCTV (Closed Circuit Television)闭路电视CMS (Cargo Monitoring System)货物监控系统DC (Direct Current)直流电DFT (Dry Film Thickness)干膜DG (Diesel Generator)柴油发电机DVD (Digital Video Disc) 数字化视频光盘EMSP (Emergency Shutter Panel)应急关断板ESS (Emergence Shutdown System)应急关闭系统GPS (Global Position System)全球定位系统HG (Harbor Generator)停泊发电机HT (High Temperature)高温JB (Junction Box)接线盒LED (Light Emitting Diode)发光二极管LT (Low Temperature)低温MCU (Main Control Unit)主控器箱MG (Main Generator)主发电机MUR (Manual Voltage Regulation)手动调压器NEMA (National Electrical Manufacturers Association) 国际电气制造业协会PA (Public Address System)公共寻呼系统PWM (Pulse Width Modulation)脉宽调制ST (Starter)启动器SWBD (Switch Board)配电盘，配电板UPS (Uninterrupted Power Supply)不间断电源VCR (Video Cassette Recorder)录像机PAINTING（涂装）:ARD (Alkyd Resin Deck)醇酸树脂甲板漆ARF (Alkyd Resin Finish)醇酸树脂面漆ARP (Alkyd Resin Primer)醇酸树脂底漆A/C (Anti-corrosive Paint)防腐漆CAF (Compressed Asbestos Fiber)压缩石棉填料EDP (Epoxy Deck Paint)环氧甲板漆EFP (Epoxy Finish Paint)环氧面漆EPP (Epoxy Primer Paint)环氧底漆ETPF (Epoxy Tank Paint Finish)环氧舱室面漆ETPP (Epoxy Tank Paint Primer)环氧舱室底漆ETP (Epoxy Topside Paint)环氧干舷漆ERL (Erosion Resistant Lacquer)防腐漆ECP (Etching Primer) 磷化底漆EPR (Ethylene-Propylene Rubber)乙丙橡胶F/C (Finish Coating)面漆IZP (Inorganic Zinc Primer)无机锌底漆IZSP (Inorganic Zinc Shop Primer)无机锌车间底漆UTP (Polyurethane Topside Primer)聚氨脂干舷漆TE (Tar Epoxy Paint)环氧焦油漆VTP (Vinyl Tar Primer)聚乙烯焦油底漆ZRP (Zinc Rich Primer)富锌底漆WELDING and Material（焊接与材料）:ASTM (American Society for Testing Materials)美国材料实验协会AWS (American Welding Society)美国焊接协会FCAW (Flux Cored Arc Welding)药芯焊丝电弧焊FRP (Fiberglass Reinforced Polyester)玻璃钢GMAW (Gas Metal Arc Welding)气体保护金属极电弧焊GRP (Glass Reinforced Polyester)玻璃钢GTAW (Gas Tungsten Arc Welding)气体保护钨极电弧焊GW (Gravity Welding)重力焊MPI (Magnetic Particle Inspection) 磁粒检验NDE (Nondestructive Evaluation)无损鉴定NDT (Nondestructive Testing)非破坏性检验PVC (Poly Vinyl Chloride)聚氯乙烯S/W (Spot Weld) 点焊SAW (Submerge Arc Welding)埋弧焊SMAW (Shielded Metal Arc Welding)手弧焊UT (Ultrasonic Test)超声波检验WPS (Welding Procedure Sheet)焊接程序表WQT (Welding Qualification Test)焊工资格检验OTHERS（其它）:AE (Assistant Engineer)助理工程师ANSI (American National Standards Institute)美国国家标准局API (American Petroleum Institute)美国石油协会ASME (American Society of Mechanical Engineers)美国机械工程师协会Bbls (Barrels) 桶（美制容量单位 1桶 = 159升），C.E. (Chief Engineer) 总工程师CEO (Chief Executive Officer)首席执行总裁CIS (Chinese Industrial Standard)中国工业标准CNOOC (China National Offshore Oil Company)中国海洋石油总公司Co Ltd.(Company Limited)（股份）有限公司cu.ft. (Cubic Feet) 立方英尺cu.in. (Cubic Inch) 立方英寸GB (Guo Biao)国标GM (General Manage)总经理H.Q. (Headquarters) 总部HSE (Health, Safety & Environment)健康，安全和环保ID (Inner Dimension)内径IEC (International Electro technical Commission)国际电工协会IMO (Intergovernmental Marine Organization)国际海事组织ISO (International Standardization Organization)国际标准化协会ITU (International Telecommunication Union)国际电信联盟Ksi (kilopounds per square inch)千磅/平方英寸N/A (None Applicable)不适用NACE (National Association of Corrosion Engineer)全国防蚀工程师协会NFPA (National Fire Protection Association)国家防火协会OD (outer Dimension)外径QA (Quality Assurance)质量保证QC (Quality Control)质量管理（检查）ST (Short Ton)短吨SOLAS (International Convention of the Safety of Life at Sea)国际海上人命安全公约Spec. (specification)说明书，规格书sq.ft. (Square Feet) 平方英尺sq.in. (Square Inch) 平方英寸PROPER NOUN（专有名词）:Basic Design(基础设计): Preparation of specification and plans/drawings outlining the design and in sufficient detail to gain Class approval. 总括性的设计规格书和图纸等，其详细程度仅足可以通过船级社认可其设计思想。
各种船型英文缩写
各种船型英文缩写（一）Bulk Carrier (散货船)- Handysize (灵便型) ：2~5万吨左右，大灵便型：大于4万吨- Panamax（巴拿马型）: 6~7.5万吨，船的总长小于或等于274.32M，型宽小于或等于32.30M；目前平均载重吨达到8.2万吨- Kmsarmax（卡尔萨姆型）:8~8.9999万吨- Capesize（好望角型）:15万吨左右Container（集装箱）（货舱区分：中央部位货舱——集装箱船；其他舱位——普通杂货船可变换区分：货舱内结构可拆装——集装箱船；不可拆装——普通杂货船）Oil Tanker（油轮）- ULCC(巨型原油轮):大于30万吨- VLCC(超大原油轮)：20~30万吨- Suezmax(苏伊士型)：12~16万吨- Aframax(阿芙拉型)：8~12万吨- Panamax(巴拿马型)：6~8万吨各种船型英文缩写（二）按照字母首位顺序排列：BBC:Bulk Carrier 散货船CCOT:Cargo Oil Tanker 货油轮DDFF: 高速渡轮EERRV: 救援船FFLNG: 浮式液化天然气船（科代替岸上传统的液化天然气工厂）FPSO: 浮式生产储油船FPV: 浮式生产设备GG-Cargo Ship: 杂货船LLNG: 液化天然气船LEG: 液化乙烯汽船LPG: 全压式液化石油汽船LSV: 驳运支援船LR成品油轮:stands for large range, 远程成品油轮MMR成品油轮:stands for medium range, 中程成品油轮OOSV:Offshore Support Vessel, 海洋工程船PPSV: 平台供应船PC: 重型石油化学制品运输船PCC:Pure Car Carrier 汽车运输船PCTC:Pure Car & Truck Carrier 大型轿车卡车专用船RRO-RO SHIP: 客滚船Roll-on/Roll-off ship: 滚装船UUCLL: Ultra Large Crude Carrier: 超大型原油轮VVLOC: 大型矿砂船VLCC: 巨型原油轮VLGC: 大型液化气体运输船。
船舶简称
船舶简称各种船型英文缩写（一）按照字母首位顺序排列：Carrier (散货船)其类型分类有：- Handysize (灵便型) ：2~5万吨左右，大灵便型：大于4万吨- Panamax（巴拿马型）: 6~万吨，船的总长小于或等于，型宽小于或等于；目前平均载重吨达到万吨- Kmsarmax（卡尔萨姆型）:8~万吨- Capesize（好望角型）:15万吨左右（集装箱）（货舱区分：中央部位货舱——集装箱船；其他舱位——普通杂货船可变换区分：货舱内结构可拆装——集装箱船；不可拆装——普通杂货船） Tanker（油轮）其类型分类有：- ULCC(巨型原油轮):大于30万吨- VLCC(超大原油轮)：20~30万吨- Suezmax(苏伊士型)：12~16万吨- Aframax(阿芙拉型)：8~12万吨- Panamax(巴拿马型)：6~8万吨各种船型英文缩写（二）按照字母首位顺序排列：BBC:Bulk Carrier 散货船CCOT:Cargo Oil Tanker 货油轮DDFF: 高速渡轮EERRV: 救援船FFLNG: 浮式液化天然气船（科代替岸上传统的液化天然气工厂）FPSO: 浮式生产储油船FPV: 浮式生产设备GG-Cargo Ship: 杂货船LLNG: 液化天然气船LEG: 液化乙烯汽船LPG: 全压式液化石油汽船LSV: 驳运支援船LR成品油轮:stands for large range, 远程成品油轮MMR成品油轮:stands for medium range, 中程成品油轮OOSV:Offshore Support Vessel, 海洋工程船PPSV: 平台供应船PC: 重型石油化学制品运输船PCC:Pure Car Carrier 汽车运输船PCTC:Pure Car & Truck Carrier 大型轿车卡车专用船RRO-RO SHIP: 客滚船Roll-on/Roll-off ship: 滚装船UUCLL: Ultra Large Crude Carrier: 超大型原油轮VVLOC: 大型矿砂船VLCC: 巨型原油轮1、DWTDWT 是DEAD WEIGHT TONNAGE 的缩写，是表示“载重吨”。
各种船型介绍
Types of veseels(carriers)因分类方式的不同，同一条船舶可有不同的称呼。
多数船舶是按船舶的用途分类称呼的。
按用途的不同，可分为：客货船；普通货船；集装箱船、滚装船、载驳船；散粮船、煤船、兼用船；兼用船（矿石／油船、矿石／散货船／油船）特种货船（运木船、冷藏船、汽车运输船等）；油船、液化气体船、液体化学品船等。
客货船：除了载运旅客之外，还装载有部分货物（水线以下的船舱尽可能用来装货）。
客货船在要求上与客船相同。
普通货船(general cargo)：俗称为杂货船。
杂货，也称为统货，是指机器设备、建材、日用百货等各种物品。
专门运输包装成捆、成包、成箱的杂货的船，称为杂货船或称普通货船。
杂货船有下列一些特征：（1）载重量不可能很大，远洋的杂货船总载重量为10000吨- 14000吨左右；近洋的杂货船总载重量为5000吨左右；沿海的杂货船总载重量为3000吨以下（由于货种多，货源不足，装卸速度慢，停港时间长，杂货船的载重量过大会不经济）。
（2）为了理货方便，杂货船一般设有2-3层甲板。
载重量为万吨级的杂货船，设有5个- 6个货舱。
机舱位置多数位于中后机型，也有的采用尾机型。
（3）杂货船一般都设有首楼，在机舱的上部设有桥楼。
老式的5000吨级杂货船，多采用三岛型。
（4）许多万吨级的杂货船，因压载的要求，常设有深舱，同时深舱可以用来装载液体货物（动植物油、糖蜜等）。
（5）杂货船一般都装设有起货设备，多数以吊杆为主，也有的装有液压旋转吊。
（6）大多数杂货船，每个货舱一个舱口，但少数杂货船根据装卸货物的需要，采用双排舱口。
（7）不定期的杂货船一般为低速船。
航速过高对于杂货船是很不经济的。
远洋杂货船约为14节-18节，续航力为12000海里以上；近洋杂货船的船速约为13节一15节；沿海杂货船的航速约为11节- 13节。
（8）杂货船一般都是一部主机，单螺旋桨。
集装箱船(container vessel)：集装箱船，是专门运输集装箱货物的船舶。
各种船型英文缩写
各种船型英文缩写各种船型英文缩写（一）Bulk Carrier (散货船)- Handysize (灵便型) ：2~5万吨左右，大灵便型：大于4万吨- Panamax（巴拿马型）: 6~7.5万吨，船的总长小于或等于274.32M，型宽小于或等于32.30M；目前平均载重吨达到8.2万吨- Kmsarmax（卡尔萨姆型）:8~8.9999万吨- Capesize（好望角型）:15万吨左右Container（集装箱）（货舱区分：中央部位货舱——集装箱船；其他舱位——普通杂货船可变换区分：货舱内结构可拆装——集装箱船；不可拆装——普通杂货船）Oil Tanker（油轮）- ULCC(巨型原油轮):大于30万吨- VLCC(超大原油轮)：20~30万吨- Suezmax(苏伊士型)：12~16万吨- Aframax(阿芙拉型)：8~12万吨- Panamax(巴拿马型)：6~8万吨各种船型英文缩写（二）按照字母首位顺序排列：BBC:Bulk Carrier 散货船CCOT:Cargo Oil Tanker 货油轮DDFF: 高速渡轮EERRV:救援船FFLNG: 浮式液化天然气船（科代替岸上传统的液化天然气工厂）FPSO: 浮式生产储油船FPV: 浮式生产设备GG-Cargo Ship: 杂货船LLNG: 液化天然气船LEG: 液化乙烯汽船LPG: 全压式液化石油汽船LSV: 驳运支援船LR 成品油轮:stands for large range, 远程成品油轮MMR成品油轮:stands for medium range, 中程成品油轮OOSV:Offshore Support Vessel, 海洋工程船PPSV: 平台供应船PC: 重型石油化学制品运输船PCC:Pure Car Carrier 汽车运输船PCTC:Pure Car & Truck Carrier 大型轿车卡车专用船RRO-RO SHIP: 客滚船Roll-on/Roll-off ship: 滚装船UUCLL: Ultra Large Crude Carrier: 超大型原油轮VVLOC: 大型矿砂船VLCC: 巨型原油轮VLGC: 大型液化气体运输船。
船舶常用英语(一)
accommodation居住舱室
accommodation deck起居舱室；旅客甲板accommodation ladder舷梯
accommodation ladder platform舷梯平台accommodation ladder manrope舷梯扶索
after body后（部船）体
inland waterway vessel内河船
civil ship; merchant ship民用船；商船
transport ship运输船
pleasure yacht游艇
passenger ship客船
coasting passenger and cargo ship沿海客货船
passenger and auto-car carrier旅客及汽车运输船
cattle carrier运牲畜船
multi-purpose ship多用途船
liquid cargo ship液体货货船
chemical tank化学品液货船
liquid chemical tanker液体化学品船
liquefied gas carrier液化气体船
liquefied petroleum gas tanker(LPG)液化石油气运输船
bilge strake(plate)舭列板
bilge well污水井
bitt系缆桩
bollard系缆桩；系船柱；双系柱
bolster枕垫
bonnet烟囱帽；机罩
boom杆；吊杆；桁；叉架
boom crutch(support; rest)吊杆支架
bossing尾管突出部；轴包套
bottom frame船底横骨
船舶简称
船舶简称各种船型英文缩写（一）按照字母首位顺序排列：1.Bulk Carrier (散货船)其类型分类有：- Handysize (灵便型) ：2~5万吨左右，大灵便型：大于4万吨- Panamax（巴拿马型）: 6~7.5万吨，船的总长小于或等于274.32M，型宽小于或等于32.30M；目前平均载重吨达到8.2万吨- Kmsarmax（卡尔萨姆型）:8~8.9999万吨- Capesize（好望角型）:15万吨左右2.Container（集装箱）（货舱区分：中央部位货舱——集装箱船；其他舱位——普通杂货船可变换区分：货舱内结构可拆装——集装箱船；不可拆装——普通杂货船）3.Oil Tanker（油轮）其类型分类有：- ULCC(巨型原油轮):大于30万吨- VLCC(超大原油轮)：20~30万吨- Suezmax(苏伊士型)：12~16万吨- Aframax(阿芙拉型)：8~12万吨- Panamax(巴拿马型)：6~8万吨各种船型英文缩写（二）按照字母首位顺序排列：BBC:Bulk Carrier 散货船CCOT:Cargo Oil Tanker 货油轮DDFF: 高速渡轮EERRV: 救援船FFLNG: 浮式液化天然气船（科代替岸上传统的液化天然气工厂）FPSO: 浮式生产储油船FPV: 浮式生产设备GG-Cargo Ship: 杂货船LLNG: 液化天然气船LEG: 液化乙烯汽船LPG: 全压式液化石油汽船LSV: 驳运支援船LR成品油轮:stands for large range, 远程成品油轮MMR成品油轮:stands for medium range, 中程成品油轮OOSV:Offshore Support Vessel, 海洋工程船PPSV: 平台供应船PC: 重型石油化学制品运输船PCC:Pure Car Carrier 汽车运输船PCTC:Pure Car & Truck Carrier 大型轿车卡车专用船RRO-RO SHIP: 客滚船Roll-on/Roll-off ship: 滚装船UUCLL: Ultra Large Crude Carrier: 超大型原油轮VVLOC: 大型矿砂船VLCC: 巨型原油轮1、DWTDWT 是DEAD WEIGHT TONNAGE 的缩写，是表示“载重吨”。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
各种船型英文缩写（一）
Bulk Carrier (散货船)
- Handysize (灵便型) ：2~5万吨左右，大灵便型：大于4万吨
- Panamax（巴拿马型）: 6~7.5万吨，船的总长小于或等于274.32M，型宽小于或等于32.30M；目前平均载重吨达到8.2万吨
- Kmsarmax（卡尔萨姆型）:8~8.9999万吨
- Capesize（好望角型）:15万吨左右
Container（集装箱）
（货舱区分：中央部位货舱——集装箱船；其他舱位——普通杂货船
可变换区分：货舱内结构可拆装——集装箱船；不可拆装——普通杂货船）
Oil Tanker（油轮）
- ULCC(巨型原油轮):大于30万吨
- VLCC(超大原油轮)：20~30万吨
- Suezmax(苏伊士型)：12~16万吨
- Aframax(阿芙拉型)：8~12万吨
- Panamax(巴拿马型)：6~8万吨
BC:Bulk Carrier 散货船
COT:Cargo Oil Tanker 货油轮
DFF:高速渡轮
ERRV:救援船
FLNG:浮式液化天然气船（科代替岸上传统的液化天然气工厂）
FPSO:浮式生产储油船
FPV:浮式生产设备
G-Cargo Ship:杂货船
LNG:液化天然气船
LEG:液化乙烯汽船
LPG:全压式液化石油汽船
LSV:驳运支援船
LR成品油轮:stands for large range,远程成品油轮MR成品油轮:stands for medium range,中程成品油轮OSV:Offshore Support Vessel,海洋工程船
PSV:平台供应船
PC:重型石油化学制品运输船
PCC:Pure Car Carrier 汽车运输船
PCTC:Pure Car & Truck Carrier 大型轿车卡车专用船RO-RO SHIP:客滚船
Roll-on/Roll-off ship:滚装船
UCLL: Ultra Large Crude Carrier: 超大型原油轮VLOC:大型矿砂船
VLCC:巨型原油轮。