PCB行业专业词汇大全
PCB专业术语大汇集
PCBJargon(PCB专业术语) AAbsorption 吸收、吸入Accelerated Test（Aging）加速实验、加速老化Accelerator 加速剂、速化剂Accept/Acceptance 允收Acceptable Quality Level（AQL）允收品质水准Accuracy 准确度ACF：Adhesive copper foil 有胶铜箔Activator 活化剂、添加剂比称为ActivatorActive parts（Devices）主动零件，指积体电路或电晶体Addition Agent 添加剂Additive Process 加成法、分全加成、半加成及部份加成Adhesion 附著力Adhesive 胶类或接著剂Aging 老化Air Knife 风刀Ambient Temperature 环境温度Ampere 安培Amp-Hour 安培小时Annular Ring 孔环Anode 阳极Anode Bag 阳极带ANSI: American National Standard Institute 美国规范协会Anti-Forming Agent 消泡剂AOI: Automatic Optical Inspection 自动光学检验Aperture 开口APQP: Advanced Product Quality PlanArray 排列、阵列Artwork 底片ASIC: Application Specific Integrated Circuit 特定用途的积体电路器Aspect Ratio 纵横比、板厚与孔径之比值Assembly 装配、组装ATE: Automatic Testing Equipment 自动电测设备AVL: Approved Vender List 合格供应商BBack Light（Back Lighting）背光法Back-UP 垫板Backpanels/Backplanes 背板、支持板，厚度较厚，Ball Grid Array（BGA）球脚车列（封装）Barrel 孔壁Base Material 基材Batch 批（同时间发料某一数量的板子）Bevelling 切斜边Binder 黏结剂Black oxide 黑氧化层，另有棕氧化（Brown Oxide）Blind Via Hole 盲导孔Blister 局部性分层或起泡Blockout 封网，网板之空网处以水溶胶涂满Blow Hole 吹孔，PTH孔壁有破洞（void）所造成Boiler (Water Tube Boiler/ Fire Tube Boiler)BOM: Bill of Material 用料表Bond Strength 结合强度Bonding Sheet(Layer) 接合片、接著层，指PPBonding Wire 结合线，IC之晶片与PCB之引线Bow 板弯Break-away Panel 可断开板或者说Break Away TabBreak Point 出像点、影像点Break-Out 破出（钻孔破出开成断环情形）Bridging 搭桥、桥接Brightener 光泽剂Brush Plating 刷镀BTU/British Thermal Unit 英制热量单位Bump 突块Buried Via Hole 埋导孔Burn-in 高温加速老化实验Burning 烧焦Burr 毛头Buy-off 认可CCAD: Computer Aided Design 电脑辅助设计CAM: Computer Aided Manufacturing 电脑辅助制造CAT: Computer Aided Testing 电脑辅助测试Capacitance 电容Carbide 碳化物、碳化钨钻头CAR: Corrective Action Report 改善报告Carbon Treatment 活性碳处理Card 卡板Carrier 载体Cartridge 滤芯Cathode 阴极CCL: Copper Clad Laminates 铜箔基板Ceramics 陶瓷Certificate 证明书CFC 氟氯碳化物 Chloro-Fluoro-CarbonChamfer 倒角、去掉直角Characteristic Impedance 特性阻抗Cheek list 检察清单Chip 晶粒、晶片Chip On Board 晶片黏著板Clean Room 无尘室 (Class 100)Cleanliness 清洁度Clearance 余隙、余环COB（Chip on Board）晶片在板上直接组装COC（Certificate of Compliance）出货合格书COF（Chip on Flexible PCB）COG（Chip glass）Coefficient of Thermal Expansion 热膨胀系数（CTE）Cold Solder Joint 冷焊点Component Hole 零件孔Component Side 组件面、零件面Conditioning 整孔Conductivity 导电度Connector 连接器Continuity Test 连通性实验Copper Foil 铜箔、铜皮Copper Ball 铜球Corner Crack 镀通孔转角断角Cp: Capability of Process 制程能力指数Crack 裂痕Crazing 白斑（基板外观上的缺点）Crosstalk 杂讯、串讯Cure/Curing 硬化、热化Current Density （C.D.）电流密度（1 ASD=9.1 ASF）Curtain Coating 液涂法Datum 基准点Deburring 去毛头Defect 不良缺点Degreasing 脱脂Delamination 分层、爆板Dent 凹陷、缓和均匀的下陷Desmearing 除胶渣Developer 显像液Deviation 偏差Device 电子元件Dewetting 缩锡DFM: Design for Manufacturing/Dirty foreign Materials 异物、杂质Die 冲模Dielectric 介质Dielectric Constant 介质常数Dimensional Stability 尺度安定性DIP（Dual Inline Package）双排脚封装体Direct Plating 直接电镀DI Water 纯水 (De-Ionize Water)DOE/Design of Experiment 实验计划法DPPM（Defect Parts Per Million）Drilling 钻孔Drill Bit 钻针Dry Film 干膜Dummy 假镀EECN: Engineering Change Notice 工程变更通知Elongation 延伸性EMI 电磁干扰 Electromagnetic InterferenceENIG: Electroless Nickel Immersion Gold 化镍浸金Entek 有机护铜处理Entry Material 盖板E.T/Electric Test 电测、电气测试Epoxy Resin 环氧树脂ESD: Electro-Static Discharge 静电流量Etching 蚀刻Etchback 加蚀Etch Factor 蚀刻函数Etching Resist 抗蚀阻剂Expose Copper 漏铜Exposure 曝光Eyelet 铆钉 RivetFAAR（First Article Approval Report）Failure 故障、损坏Fault 缺陷、瑕疵FCC/Federal Communication Commission 美国联邦通讯委员会Fiber Exposure 玻织显露Fiducial Mark 基准记号、光学点Film 底片Filter 过滤器Fine Line 细线Finger 手指Finishing 制成品在外观上的最后处理First Article 试产的首件或首批小量产品First Pass-Yield 初检良品率Fixture 夹具、治具 (Rig and Fixture)Flame Resistant 耐燃性（分HB、VO、V1及V2等四级）Flux 助焊剂Foil Burr 铜箔毛边Foot Pint（Land Pattern）脚垫Foreign Material 外来物、异物FR4/Flame Resistant Laminates 耐燃性积层板材Frequency 频率GGauge 量规Gel Time 胶化时间Gerber Data/Gerber File 格搏档案Glass Fiber 玻璃纤维Glass Fiber Protrusion 玻纤突出Glass Transition Temperature/Tg 玻璃态转化温度Golden Board 测试用规范板Grid 规范格Ground Plane 接地层Guide Pin 导针HHaloing 白圈、白边（在钻孔、开槽等机械动作一旦过猛时将造成内部树脂之破碎或微小分层裂开的现象）Hardener 硬化剂Hardness 硬度Heat Dissipation 散热Hertz（Hz）赫芝HEPA/High Efficiency Particulate Air Filter 高效空气尘粒过滤机Hipot Test 高压电测 High Potential TestHit 擎Holding Time 停区时间Hole Block 孔塞Hole Breakout 孔位破出，简称BreakoutHole counter 数孔机Hole Density 孔数密度Hole Pull Strength 孔壁强度Hole Void 破洞Hot Air Levelling 喷锡 HASL/HALTHE(High Temperature Elongation) 高温延伸性II.C.Socket 积体电路插座Image Transfer 影像转移IMC: Inter-metallic compound 介面合金共化物Immersion Plating 浸镀Impedance 阻抗In-Circuit Testing 组装板电测，ICTIndexing Hole 基准孔Infrared(IR) 红外线Ink 油墨Inner Layer 内层Input/Output 输入、输出Insert/Insertion 插接、插装Insulation Resistance 绝缘电阻Integrated Circuit (IC) 积体电路器Interconnection互连Intermatallic Compound(IMC) 介面合金共化物Internal Stress 内应力Ion Cleanliness 离子清洁度Ionic Contamination 离子污染IPC: The Institute for Interconnecting and Packaging Electronic Circuits 美国印刷电路板协会ISO: International Organization for Standardization 国际规范组织Isolation 隔离性JJPCA/Japan Print Circuit Association 日本印刷电路工业会Just-In-Time(JIT) 适时供应KKeyboard 键盘Kraft Paper 牛皮纸LLaminate(s) 基板、积层板Laminator 压膜机Land 孔环焊垫、独立点Landless Hole 无环通孔Laser Direct Imaging/LDI 雷射直接成像Laser Photoplotter 雷射曝光机、绘图机Lay Out 布线、布局 (configuration, general arrangement) Lay Up 叠合Lead Frame 脚架Lead 引脚、接脚Legend 文字标记Levelling 整平Light Intensity 光强度LMW: License Manufacturing Warehouse 保税厂Lot Size 批量LRR(Lot Reject Rate)MMajor Defect 严重缺点、主要缺点Marking 标记Mask 阻剂Mass Lamination 大型压板MCM/Multi-Chip Module 多晶片模组Measling 白点Membrane Switch 薄膜开关Microctching 微蚀Microsectioning 微切片法Migration迁移Mil 英丝0.001 inmisregistration 对不准、对不准度MLB/Multi-Layer Board 多层板Modem 调变及解调器、数据机Modification 修改、改变Module 模组Mother Board 主机板NNail Head 钉头N.C.数值控制（Numerical Control）Negative 负片Negative etch-back 反回蚀Nick 缺口Node 节点Nodule 瘤Non-Conformance 不合格品Non-flammable 非燃性Non-wetting 不沾锡Normal Distribution 常态分配NPI：New project introduction)NRE Charge-Non-Recurring Engineering Charge 不会重收的工程费用OOhm 欧姆Omega Meter 离子污染检测仪Open Circuits 断线Optical Density 光密度Optical Inspection 光学检验Organic Solderability Preservatives(OSP) 有机保焊剂Outgassing 出气、吹气Output 产出、输出Overflow 溢流Oxidation氧化Ozone Depletion 臭氧层耗损PPackaging 封装、购装Packing 包装Pad 配圈、孔环焊垫Panel Plating 全板镀铜Passive Parts 被动零件，如电阻、电容Past 膏（锡膏Solder Paste）Pattern Plating 线路电镀PCB/Printed Circuit Board 印刷电路板Peel Strength 抗撕强度Peripheral 周边附属设备Phototool 底片（一般指偶氮棕片 Diazo Film）Pin Grid Array(PGA) 矩阵式针脚封装Pinhole 针孔Pin 接脚、插梢、插针Pink Ring 粉红圈Pits 凹点（小面积下陷）Pitch 脚距、垫距、线距Plasma 电浆Plated through Hole/PTH 镀通孔Plug 插脚、塞孔Polarization 分极、极化Polyimide(PI) 聚亚酸胺Popcorn Effect 爆M花效应Post Cure 疏孔度实验Power Plane 后续硬化、后烤Power Supply 电源层PPM/Parts Per Million 百万分之几Preheat 预热Prepreg 胶片、树脂片Press Plate 压合钢板Press-Fit Contact 挤入式接触Printing 印刷Probe 探针Profile 轮廓、部面图、升温曲线图积线Punch 横切、冲床QQIT(Quality improvement Team) 品质改善小组Qualified Products List 合格产品（供应者）名单RRadiometer 辐射计、光度计Radius 尺角、半径Reference Dimension 参考尺度、参考尺寸Reflow Soldering 重熔焊接、熔焊Registration 对准度Reject 剔退、拒收Reliability 可靠度、信赖度Repair 修理Resin Content 胶含量、树脂含量Resin Flow 胶流量、树脂流量Resist 阻剂、阻膜Resistor 电阻器、电阻Resolution 解像、解像度、解读度Resolving Power 解读力、解像力（分辨力）Rework(ing) 重工、再加工Ring 套环Roller Cutter 混切机（俗称锯板机）Roller Coating 滚动涂布法Routing 切外型、捞外型RRM: Revolutions per Minute 转速（每分钟）Run-out 偏转、绕转、累积距差SSCAR(Supplier CA Request) 供应商改善报告SCM: Supply chain Management 供应商经管系统Scratch 刮痕Screen Printing 网版印刷Scrubber 磨刷机、磨刷器Selective Plating 选择性电镀SEM/Scanning Electron Microscope 扫瞄式电子显微镜Semi-Conductor 半导体Shearing 剪、裁切Short 短路SIR(Surface Insulation Resistance) 表面绝缘电阻Side Wall 侧壁Sigma(Standard Deviation) 规范差Signal 讯号Silicon 矽Silk Screen 网版印刷、丝网印刷Skin Effect 集肤效应Skip Printing 漏印Slot 槽孔Smear 胶渣SMT/Surface Mount Technology 表面黏装技术Solder 焊锡Solderability 焊锡性Solder Ball 锡球Solder Bridging 锡桥Solder Bump 焊锡凸块Solder Dam 锡堤（IC脚间的防焊）Solder Levelling 喷锡、热风整平Solder Mask(S/M) 绿漆、防焊膜Solder Paste 锡膏Solder Plug 锡塞、锡柱Solder Pot 锡炉Solder Side 焊锡面Soldering Fluid/Soldering Oil 助焊液、护焊汕Solid Content 固体含量SOP(Standard Operation Procedure) 规范作业程序Spacing 间距SPC/Statistical Process Control 统计制程管制Specific Gravity SG比重Specification(Spec) 规范、规格Specimen 样品、试样Spindle 钻轴Spray Coating 喷著涂装Stencil 版膜、网版Storage condition 储存条件Stress Relief 消除应力Substrate 底材Surface Insulation Resistance(SIR) 表面绝缘电阻Surface Tenting 表面张力Surface-Mount Device 表面黏装零件Swelling Agents/Sweller 膨胀剂SWR(Special Working Request) 试产前之“特殊工作要求”TTab 接点、金手指Tape 撕胶带实验Teflon 铁氟龙Temperature Profile 温度曲线Template 模板Tensile Strength 抗拉强度Tenting 盖孔法Terminal 端子Thermal Stress 热应力Thermal Shock 热冲击Thin Copper Foil 薄铜箔Then film Technology 薄膜技术Throwing Power 分布力Tolerance 公差Touch Up 检修（简单的工具在手操作下即可进行的小规范的检修，称之Touch Up或Rewok 有些类似）Trace 线路、导线Traceability 追溯性、可溯性Transistor 电晶体Transmission Line 传输线Twist 板翘、板扭UUL 保险业实验 Underwriters Laboratories/INCUltra Violet Curing(UV Curing) 紫外线硬化Ultrasonic Cleaning 超音波清洗Undercut/Undercutting 侧蚀Universal Tester 万用型电测机VVacuum Lamination 真空压合Vacuum Packing 真空包装Viscosity 黏滞度、黏度Vision Systems 视觉系统Visual Examination(Inspection) 目视检查Voltage 电压WWafer 晶圆Warp/Warpage 板弯Warp and Twist 板弯翘Washer 垫圈Waste Treatment 废弃处理Water Absorption 吸水性Water Break 水膜破散、水破Watermark 水印Wave Soldering 波焊Weave Exposure 织纹显露Weave Texture 织纹隐现Welding 熔接Wet Process 湿式制程Wetting Balance 沾锡、沾湿White Spot 白点Wicking effect 灯芯效应Wire Bonding 打线结合WIP(Working Piece in Process) 在制品XX Axis X轴X-Ray X光YY-Axis Y轴Yield 良品率、良率、产率ZZ-Axis X轴OtherHDI-High Density inter-connect 高密度内连接SWOT Strengths Weaknesses Opportunities ThreatsCD: Compact DiscCPU: Central Process UnitLaser, YAG Laser)DLD: Direct Laser Drilling (CO2DVD: Digital Versatile DiscEEPROM: Electrically Erasable Programmable Read Only Memory EMS: Electronics Manufacturing ServiceGPS: Global Positioning ServiceHDD: Hard Disk DriveHDTV: High Density TVLCD: Liquid Crystal DisplayLED: Light Emitting DiodeVCD: Video Compact DiskQuality System Requirements QS-9000(質量體系要求)Advanced Product Quality Planning and Control Plan APQP(產品質量先期策劃和控制計劃)Measurement Systems Analysis MSA(測量系統分析)Potential Failure Mode and Effects Analysis FMEA(潜在失效模式與後果分析) Production Part Approval Process PPAP (生產件批准程序)Statistical Process Control SPC (統計過程控制)IPC-A-600Classification 分级Acceptance Criteria 允收规格Applicable Documents 参考资料Dimensions And Tolerances 尺度与公差Terms And Definitions 术语及定义Workmanship 工艺水准Externally Observable Characteristics 外观特性Board Edges 板边Burrs 看头、毛刺Nonmetallic Burrs 非金属性毛头Metallic Burrs 金属毛头Nicks 缺口Haloing 白边Base Material 基材Weave Exposure 织纹显露Weave Texture 织纹隐现Exposed/Disrupted Fibers 玻织曝露/扰乱Pits and Voids 凹点与凹坑Base Material Subsurface 基材次表面Measling白点Crazing白斑Delamination/Blister分层/起泡Foreign Inclusions外来夹杂物Solder Coatings and Fused Tin Lead喷锡板或熔锡板Nonwetting拒锡（不沾锡）Dewetting缩锡Holes-Plated-Through-General镀通孔概要Nodules/Burrs镀瘤/毛头Pink Ring粉红圈Voids-Copper Plating镀铜层破洞Voids-Finished Coating完工皮膜之镀层破洞Lifted Lands-(Visual)孔环浮离（目检）Holes-Unsupported未镀孔Haloing白圈Printed Contacts板边接触金手指Surface Plating-General表面镀层通则Surface Plating-Wire Bond Pads打线承垫之表面Burrs on Edge-Board Contacts板边接点之毛头Adhesion of Overplate表面镀层之附着力Marking标记Etched Marking蚀刻标记Screened or Ink Stamped Marking纲印或盖印之标记Solder Resist(Solder Mask)防焊绿漆Coverage Over Conductors (Skip Coverage)边线表面之覆盖性（覆盖不全、跳印）Registration to Holes (All Finishes)对孔之套准度（各种表处理层）Registration to Other Conductive Patterns其他防焊的对准性Ball Grid Array (Solder Resist-Defined Lands)球脚格列体之焊垫（绿漆设限之焊垫）Ball Grid Array (Copper-Defined Lands)球脚格列体（铜面设限之焊垫）Ball Grid Array (Solder Dam)球脚格列体（防焊堤）Blisters/Delamination起泡/分层Adhesion(Flaking or Peeling)附著力（破片或剥落）Waves/Wrinkles/Ripples起浪/起皱/纹路Tenting(Via Holes)盖孔（导通孔、过孔）Pattern Definition-Dimensional圆形尺度特性Conductor Width and Spacing线宽与间距Conductor Width线宽Conductor Spacing导线间距External Annular Ring-Measurement孔环测量External Annular Ring-Supported Holes有孔壁支援的外孔环External Annular Ring-Unsupported Holes无孔壁支援的外孔环Flatness平坦度Internally Observable Characteristics可观察到的内在特性Dielectric Materials介质材料Laminate Voids(Outside Thermal Zone)压板空洞（或热区之外）Registration/Conductors to Holes导体与通孔之间的对准度Clearance Hole/Unsupported/to Power/Ground Planes针对电源层或接地层具隔环之非镀通孔Delamination/Blister分层/起泡Etchback回蚀Negative Etchback反回蚀Smear Removal除胶渣Dielectric Material/Clearance/Metal Plane for Supported Holes 金属层与通孔壁之介质隔距Layer-to-Layer Spacing层与层之间距Resin Recession树脂缩陷Conductive Patterns-General导线概论Etching Characteristics蚀刻特性Print and Etch印后即蚀刻（指正片法）Surface Conductor Thickness(Foil Plus Plating)表导体厚度（铜箔加电镀铜）Foil Thickness-Internal Layers内层箔厚Plated-Through Holes-General镀通孔概论Annular Ring-Internal Layers各内层之孔环Lifted Lands-(Cross-Sections)焊环浮起（切片上所见）Foil Crack-(Internal Foil)“C”Crack内层铜箔之裂纹Foil Crack-(External Foil)镀层破裂Plating Crack-(Barrel)“E”Crack孔壁镀层破裂Plating Crack-(Corner)“F”Crack孔角镀层破裂Plating Nodules镀层长瘤Copper Plating Thickness-Hole Wall孔壁镀铜厚度Plating Voids镀层破洞Solder Coating Thickness (Only When Specified)焊锡皮膜厚度（当已规定检查者）Solder Resist Thickness绿漆厚度Wicking灯芯效应（指玻织束渗入化学铜）Wicking/Clearance Holes隔离孔之渗铜Innerlayer Separation-Vertical (Axial) Microsection内层（环）分离-垂直（纵断面）微切片Innerlayer Separation-Horizontal (Transverse) Microsection内层（环）分离-水平（横断面）微切片Material Fill of Blind and Buried Vias盲孔与埋孔之填充材料钻孔式镀通孔Plated-Through Holes-Drilled钻孔式镀通孔Burrs毛头Nailheading钉头Plated-Through Holes-Punched冲孔式镀通孔Roughness and Nodules粗糙与镀瘤Flare喇叭口Miscellaneous其他离顶Flexible And Rigid-Flex Printed Wiring软性及软硬合板Metal Core Printed Boards金属平心电路板Type Classifications型式分类Spacing Laminated Type间距压合板Insulation Thickness/Insulated Metal Substrate已绝缘金属底材之绝缘厚度Insulation Material Fill/Laminated Type Metal Core压合型金属平心之绝缘填料Cracks in Insulation Material Fill/Laminated Type压合型绝缘填充料之裂纹Core Bond to Plated-Through Hole Wall平心层与镀通孔之间的固著Flush Printed Boards表面全平板Flushness of Surface Conductor表面导线之平坦性Cleanliness Testing清洁度实验Solderability Testing焊锡性实验Plated-Through Holes镀通孔Electrical Integrity电性之完整。
pcb常用的专业术语
pcb常用的专业术语PCB常用的专业术语PCB，即印刷电路板，是电子产品中不可或缺的一部分。
在PCB制造过程中，有许多专业术语需要了解。
本文将从材料、工艺、设计等方面介绍PCB常用的专业术语。
一、材料1.基板（Substrate）基板是指印刷电路板上的主体部分，通常由玻璃纤维和树脂复合材料构成。
基板的质量直接影响着整个PCB的性能。
2.铜箔（Copper Foil）铜箔是印刷电路板上最重要的导电层材料，其厚度通常为18um至105um之间。
铜箔的质量和厚度对于PCB的导电性能和可靠性有着重要影响。
3.覆铜板（Copper Clad Board）覆铜板是指在基板表面涂覆一层铜箔而成，通常有单面、双面和多层三种形式。
不同类型的覆铜板适用于不同种类的电路设计需求。
4.阻焊（Solder Mask）阻焊是一种涂在印刷电路板上以保护未焊接区域免受污染和短路的材料。
阻焊通常为绿色、红色或蓝色，具有良好的耐高温性和化学稳定性。
5.沉金（ENIG）沉金是一种表面处理技术，可以在印刷电路板上形成一层金属保护层，提高PCB的可靠性和耐腐蚀性。
沉金通常用于高端PCB产品中。
二、工艺1.蚀刻（Etching）蚀刻是印刷电路板制造中最重要的工艺之一，其目的是去除不需要的铜箔以形成电路图案。
蚀刻过程需要使用化学溶液和光敏树脂等材料。
2.钻孔（Drilling）钻孔是指在印刷电路板上钻洞以安装元器件或连接不同层之间的导线。
钻孔需要使用高速钻头和自动化设备完成。
3.压合（Lamination）压合是指将多个覆铜板通过热压技术粘合在一起形成多层PCB结构。
压合过程需要控制温度、压力和时间等参数，确保PCB质量符合要求。
4.喷锡（Soldering）喷锡是一种表面处理技术，可以在印刷电路板上形成一层锡保护层，提高PCB的可靠性和耐腐蚀性。
喷锡通常用于中端PCB产品中。
5.贴片（SMT）贴片是指将元器件直接安装在印刷电路板上的一种技术。
PCB专业术语大汇集
PCB专业术语大汇集PCB专业术语大汇集PCB是Printed Circuit Board的缩写，即印制电路板。
作为现代电子制造中不可或缺的一个组成部分，PCB技术已经成为电子制造的核心技术之一。
如果你在PCB制造领域工作或学习，那么理解并熟练掌握一些常见的PCB专业术语是非常重要的。
在这篇文章中，我们将罗列一些重要的PCB专业术语和技术名词，以帮助大家更好地理解PCB的制造和设计。
一、PCB制造基础1. PAD:焊盘，指印制电路板上用于焊接元器件的金属区域。
2. VIA:通孔，指在印制电路板上打开的金属通孔，连接不同层之间的电路。
3. Solder mask:焊膜，是一种覆盖在PCB表面的保护层，用于防止无意中的短路和腐蚀。
4. Silk screen:丝印，是印刷在印制电路板上的文字和图像，用于标记焊点、元器件和引脚等信息。
5. Cooper:铜箔，是一种用于制造PCB的材料。
6. Substrate:衬底，指PCB中负责固定和支撑电路的材料。
7. Copper weight:铜厚度，指PCB上铜箔的厚度，单位是oz。
8. Panel:板子，指PCB制造中一组连续的PCB，通常需要在单个板子上打印多个电路。
9. Plating:镀，指将金属材料沉积在印制电路板表面或内部的过程。
10. Tolerance:公差，指PCB制造和设计中可以接受的误差范围。
二、PCB设计技术1. Trace:走线，指印制电路板上的导线，用于连接不同的元器件和电路板上的不同部分。
2. Clearance:间隙，指PCB上不同元器件或电路之间的距离。
3. Net:网络，指一个电路的连接点集合，通常用来描述PCB上的一组连通电路。
4. Gerber:杰伯，是一种文件格式，通常用于将PCB设计转化为PCB生产所需的制造文件。
5. Footprint:插件，指印制电路板上元器件焊盘的设计，用于确保元器件和焊盘正确对齐和正确连接。
PCB 制造专业术语
综合词汇1、印制电路：printed circuit2、印制线路：printed wiring3、印制板：printed board4、印制板电路：printed circuit board (pcb)5、印制线路板：printed wiring board(pwb)6、印制元件：printed component7、印制接点：printed contact8、印制板装配：printed board assembly9、板：board10、单面印制板：single-sided printed board(ssb)11、双面印制板：double-sided printed board(dsb)12、多层印制板：mulitlayer printed board(mlb)13、多层印制电路板：mulitlayer printed circuit board14、多层印制线路板：mulitlayer prited wiring board15、刚性印制板：rigid printed board16、刚性单面印制板：rigid single-sided printed borad17、刚性双面印制板：rigid double-sided printed borad18、刚性多层印制板：rigid multilayer printed board19、挠性多层印制板：flexible multilayer printed board20、挠性印制板：flexible printed board21、挠性单面印制板：flexible single-sided printed board22、挠性双面印制板：flexible double-sided printed board23、挠性印制电路：flexible printed circuit (fpc)24、挠性印制线路：flexible printed wiring25、刚性印制板：flex-rigid printed board, rigid-flex printed board26、刚性双面印制板：flex-rigid double-sided printed board, rigid-flex double-sided printed27、刚性多层印制板：flex-rigid multilayer printed board, rigid-flex multilayer printed board28、齐平印制板：flush printed board29、金属芯印制板：metal core printed board30、金属基印制板：metal base printed board31、多重布线印制板：mulit-wiring printed board32、陶瓷印制板：ceramic substrate printed board33、导电胶印制板：electroconductive paste printed board34、模塑电路板：molded circuit board35、模压印制板：stamped printed wiring board36、顺序层压多层印制板：sequentially-laminated mulitlayer37、散线印制板：discrete wiring board38、微线印制板：micro wire board39、积层印制板：buile-up printed board40、积层多层印制板：build-up mulitlayer printed board (bum)41、积层挠印制板：build-up flexible printed board42、表面层合电路板：surface laminar circuit (slc)43、埋入凸块连印制板：b2it printed board44、多层膜基板：multi-layered film substrate(mfs)45、层间全内导通多层印制板：alivh multilayer printed board46、载芯片板：chip on board (cob)47、埋电阻板：buried resistance board48、母板：mother board49、子板：daughter board50、背板：backplane51、裸板：bare board52、键盘板夹心板：copper-invar-copper board53、动态挠性板：dynamic flex board54、静态挠性板：static flex board55、可断拼板：break-away planel56、电缆：cable57、挠性扁平电缆：flexible flat cable (ffc)58、薄膜开关：membrane switch59、混合电路：hybrid circuit60、厚膜：thick film61、厚膜电路：thick film circuit62、薄膜：thin film63、薄膜混合电路：thin film hybrid circuit64、互连：interconnection65、导线：conductor trace line66、齐平导线：flush conductor67、传输线：transmission line68、跨交：crossover69、板边插头：edge-board contact70、增强板：stiffener71、基底：substrate72、基板面：real estate73、导线面：conductor side74、元件面：component side75、焊接面：solder side76、印制：printing77、网格：grid78、图形：pattern79、导电图形：conductive pattern80、非导电图形：non-conductive pattern81、字符：legend82、标志：mark二、基材：1、基材：base material2、层压板：laminate3、覆金属箔基材：metal-clad bade material4、覆铜箔层压板：copper-clad laminate (ccl)5、单面覆铜箔层压板：single-sided copper-clad laminate6、双面覆铜箔层压板：double-sided copper-clad laminate7、复合层压板：composite laminate8、薄层压板：thin laminate9、金属芯覆铜箔层压板：metal core copper-clad laminate10、金属基覆铜层压板：metal base copper-clad laminate11、挠性覆铜箔绝缘薄膜：flexible copper-clad dielectric film12、基体材料：basis material13、预浸材料：prepreg14、粘结片：bonding sheet15、预浸粘结片：preimpregnated bonding sheer16、环氧玻璃基板：epoxy glass substrate17、加成法用层压板：laminate for additive process18、预制内层覆箔板：mass lamination panel19、内层芯板：core material20、催化板材：catalyzed board ,coated catalyzed laminate21、涂胶催化层压板：adhesive-coated catalyzed laminate22、涂胶无催层压板：adhesive-coated uncatalyzed laminate23、粘结层：bonding layer24、粘结膜：film adhesive25、涂胶粘剂绝缘薄膜：adhesive coated dielectric film26、无支撑胶粘剂膜：unsupported adhesive film27、覆盖层：cover layer (cover lay)28、增强板材：stiffener material29、铜箔面：copper-clad surface30、去铜箔面：foil removal surface31、层压板面：unclad laminate surface32、基膜面：base film surface33、胶粘剂面：adhesive faec34、原始光洁面：plate finish35、粗面：matt finish36、纵向：length wise direction37、模向：cross wise direction38、剪切板：cut to size panel39、酚醛纸质覆铜箔板：phenolic cellulose paper copper-clad laminates(phenolic/paper ccl)40、环氧纸质覆铜箔板：epoxide cellulose paper copper-clad laminates (epoxy/paper ccl)41、环氧玻璃布基覆铜箔板：epoxide woven glass fabric copper-clad laminates42、环氧玻璃布纸复合覆铜箔板：epoxide cellulose paper core, glass cloth surfaces copper-clad laminates43、环氧玻璃布玻璃纤维复合覆铜箔板：epoxide non woven/woven glass reinforced copper-clad laminates44、聚酯玻璃布覆铜箔板：ployester woven glass fabric copper-clad laminates45、聚酰亚胺玻璃布覆铜箔板：polyimide woven glass fabric copper-clad laminates46、双马来酰亚胺三嗪环氧玻璃布覆铜箔板：bismaleimide/triazine/epoxide woven glass fabric copper-clad lamimates47、环氧合成纤维布覆铜箔板：epoxide synthetic fiber fabric copper-clad laminates48、聚四乙烯玻璃纤维覆铜箔板：teflon/fiber glass copper-clad laminates49、超薄型层压板：ultra thin laminate50、陶瓷基覆铜箔板：ceramics base copper-clad laminates51、紫外线阻挡型覆铜箔板：uv blocking copper-clad laminates三、基材的材料1、a阶树脂：a-stage resin2、b阶树脂：b-stage resin3、c阶树脂：c-stage resin4、环氧树脂：epoxy resin5、酚醛树脂：phenolic resin6、聚酯树脂：polyester resin7、聚酰亚胺树脂：polyimide resin8、双马来酰亚胺三嗪树脂：bismaleimide-triazine resin9、丙烯酸树脂：acrylic resin10、三聚氰胺甲醛树脂：melamine formaldehyde resin11、多官能环氧树脂：polyfunctional epoxy resin12、溴化环氧树脂：brominated epoxy resin13、环氧酚醛：epoxy novolac14、氟树脂：fluroresin15、硅树脂：silicone resin16、硅烷：silane17、聚合物：polymer18、无定形聚合物：amorphous polymer19、结晶现象：crystalline polamer20、双晶现象：dimorphism21、共聚物：copolymer22、合成树脂：synthetic23、热固性树脂：thermosetting resin24、热塑性树脂：thermoplastic resin25、感光性树脂：photosensitive resin26、环氧当量：weight per epoxy equivalent (wpe)27、环氧值：epoxy value28、双氰胺：dicyandiamide29、粘结剂：binder30、胶粘剂：adesive31、固化剂：curing agent32、阻燃剂：flame retardant33、遮光剂：opaquer34、增塑剂：plasticizers35、不饱和聚酯：unsatuiated polyester36、聚酯薄膜：polyester37、聚酰亚胺薄膜：polyimide film (pi)38、聚四氟乙烯：polytetrafluoetylene (ptfe)39、聚全氟乙烯丙烯薄膜：perfluorinated ethylene-propylene copolymer film (fep)40、增强材料：reinforcing material41、玻璃纤维：glass fiber42、e玻璃纤维：e-glass fibre43、d玻璃纤维：d-glass fibre44、s玻璃纤维：s-glass fibre45、玻璃布：glass fabric46、非织布：non-woven fabric47、玻璃纤维垫：glass mats48、纱线：yarn49、单丝：filament50、绞股：strand51、纬纱：weft yarn52、经纱：warp yarn53、但尼尔：denier54、经向：warp-wise55、纬向：weft-wise, filling-wise56、织物经纬密度：thread count57、织物组织：weave structure58、平纹组织：plain structure59、坏布：grey fabric60、稀松织物：woven scrim61、弓纬：bow of weave62、断经：end missing63、缺纬：mis-picks64、纬斜：bias65、折痕：crease66、云织：waviness67、鱼眼：fish eye68、毛圈长：feather length69、厚薄段：mark70、裂缝：split71、捻度：twist of yarn72、浸润剂含量：size content73、浸润剂残留量：size residue74、处理剂含量：finish level75、浸润剂：size76、偶联剂：couplint agent77、处理织物：finished fabric78、聚酰胺纤维：polyarmide fiber79、聚酯纤维非织布：non-woven polyester fabric80、浸渍绝缘纵纸：impregnating insulation paper81、聚芳酰胺纤维纸：aromatic polyamide paper82、断裂长：breaking length83、吸水高度：height of capillary rise84、湿强度保留率：wet strength retention85、白度：whitenness86、陶瓷：ceramics87、导电箔：conductive foil88、铜箔：copper foil89、电解铜箔：electrodeposited copper foil (ed copper foil)90、压延铜箔：rolled copper foil91、退火铜箔：annealed copper foil92、压延退火铜箔：rolled annealed copper foil (ra copper foil)93、薄铜箔：thin copper foil94、涂胶铜箔：adhesive coated foil95、涂胶脂铜箔：resin coated copper foil (rcc)96、复合金属箔：composite metallic material97、载体箔：carrier foil98、殷瓦：invar99、箔（剖面）轮廓：foil profile100、光面：shiny side101、粗糙面：matte side102、处理面：treated side103、防锈处理：stain proofing104、双面处理铜箔：double treated foil四、设计1、原理图：shematic diagram2、逻辑图：logic diagram3、印制线路布设：printed wire layout4、布设总图：master drawing5、可制造性设计：design-for-manufacturability6、计算机辅助设计：computer-aided design.(cad)7、计算机辅助制造：computer-aided manufacturing.(cam)8、计算机集成制造：computer integrat manufacturing.(cim)9、计算机辅助工程：computer-aided engineering.(cae)10、计算机辅助测试：computer-aided test.(cat)11、电子设计自动化：electric design automation .(eda)12、工程设计自动化：engineering design automaton .(eda2)13、组装设计自动化：assembly aided architectural design. (aaad)14、计算机辅助制图：computer aided drawing15、计算机控制显示：computer controlled display .(ccd)16、布局：placement17、布线：routing18、布图设计：layout19、重布：rerouting20、模拟：simulation21、逻辑模拟：logic simulation22、电路模拟：circit simulation23、时序模拟：timing simulation24、模块化：modularization25、布线完成率：layout effeciency26、机器描述格式：machine des criptionm format .(mdf)27、机器描述格式数据库：mdf databse28、设计数据库：design database29、设计原点：design origin30、优化（设计）：optimization (design)31、供设计优化坐标轴：predominant axis32、表格原点：table origin33、镜像：mirroring34、驱动文件：drive file35、中间文件：intermediate file36、制造文件：manufacturing documentation37、队列支撑数据库：queue support database38、元件安置：component positioning39、图形显示：graphics dispaly40、比例因子：scaling factor41、扫描填充：scan filling42、矩形填充：rectangle filling43、填充域：region filling44、实体设计：physical design45、逻辑设计：logic design46、逻辑电路：logic circuit47、层次设计：hierarchical design48、自顶向下设计：top-down design49、自底向上设计：bottom-up design50、线网：net51、数字化：digitzing52、设计规则检查：design rule checking53、走（布）线器：router (cad)54、网络表：net list55、计算机辅助电路分析：computer-aided circuit analysis56、子线网：subnet57、目标函数：objective function58、设计后处理：post design processing (pdp)59、交互式制图设计：interactive drawing design60、费用矩阵：cost metrix61、工程图：engineering drawing62、方块框图：block diagram63、迷宫：moze64、元件密度：component density65、巡回售货员问题：traveling salesman problem66、自由度：degrees freedom67、入度：out going degree68、出度：incoming degree69、曼哈顿距离：manhatton distance70、欧几里德距离：euclidean distance71、网络：network72、阵列：array73、段：segment74、逻辑：logic75、逻辑设计自动化：logic design automation76、分线：separated time77、分层：separated layer78、定顺序：definite sequence五、形状与尺寸：1、导线（通道）：conduction (track)2、导线（体）宽度：conductor width3、导线距离：conductor spacing4、导线层：conductor layer5、导线宽度/间距：conductor line/space6、第一导线层：conductor layer no.17、圆形盘：round pad8、方形盘：square pad9、菱形盘：diamond pad10、长方形焊盘：oblong pad11、子弹形盘：bullet pad12、泪滴盘：teardrop pad13、雪人盘：snowman pad14、v形盘：v-shaped pad15、环形盘：annular pad16、非圆形盘：non-circular pad17、隔离盘：isolation pad18、非功能连接盘：monfunctional pad19、偏置连接盘：offset land20、腹（背）裸盘：back-bard land21、盘址：anchoring spaur22、连接盘图形：land pattern23、连接盘网格阵列：land grid array24、孔环：annular ring25、元件孔：component hole26、安装孔：mounting hole27、支撑孔：supported hole28、非支撑孔：unsupported hole29、导通孔：via30、镀通孔：plated through hole (pth)31、余隙孔：access hole32、盲孔：blind via (hole)33、埋孔：buried via hole34、埋/盲孔：buried /blind via35、任意层内部导通孔：any layer inner via hole (alivh)36、全部钻孔：all drilled hole37、定位孔：toaling hole38、无连接盘孔：landless hole39、中间孔：interstitial hole40、无连接盘导通孔：landless via hole41、引导孔：pilot hole42、端接全隙孔：terminal clearomee hole43、准表面间镀覆孔：quasi-interfacing plated-through hole44、准尺寸孔：dimensioned hole45、在连接盘中导通孔：via-in-pad46、孔位：hole location47、孔密度：hole density48、孔图：hole pattern49、钻孔图：drill drawing50、装配图：assembly drawing51、印制板组装图：printed board assembly drawing52、参考基准：datum reference53. 光学定位点Fiducial mark。
PCB行业专业词汇大全
PCB行业专业词汇大全—马建整理* Process Module 说明:A. 下料( Cut Lamination)a-1 裁板( Sheets Cutting)a-2 原物料发料(Panel)(Shear material to Size)B. 钻孔(Drilling)b-1 内钻(Inner Layer Drilling )b-2 一次孔(Outer Layer Drilling )b-3 二次孔(2nd Drilling)b-4 雷射钻孔(Laser Drilling )(Laser Ablation )b-5 盲(埋)孔钻孔(Blind & Buried Hole Drilling)C. 乾膜制程( Photo Process(D/F))c-1 前处理(Pretreatment)c-2 压膜(Dry Film Lamination)c-3 曝光(Exposure)c-4 显影(Developing)c-5 蚀铜(Etching)c-6 去膜(Stripping)c-7 初检( Touch-up)c-8 化学前处理,化学研磨( Chemical Milling )c-9 选择性浸金压膜(Selective Gold Dry Film Lamination)c-10 显影(Developing )c-11 去膜(Stripping )D. 压合Laminationd-1 黑化(Black Oxide Treatment)d-2 微蚀(Microetching) d-3 铆钉组合(eyelet )d-4 叠板(Lay up)d-5 压合(Lamination)d-6 後处理(Post Treatment)d-7 黑氧化( Black Oxide Removal )d-8 铣靶(spot face)d-9 去溢胶(resin flush removal)E. 减铜(Copper Reduction)e-1 薄化铜(Copper Reduction)F. 电镀(Horizontal Electrolytic Plating)f-1 水平电镀(Horizontal Electro-Plating) (Panel Plating) f-2 锡铅电镀( Tin-Lead Plating ) (Pattern Plating)f-3 低於1 mil ( Less than 1 mil Thickness )f-4 高於1 mil ( More than 1 mil Thickness)f-5 砂带研磨(Belt Sanding)f-6 剥锡铅( Tin-Lead Stripping)f-7 微切片( Microsection)G. 塞孔(Plug Hole)g-1 印刷( Ink Print )g-2 预烤(Precure)g-3 表面刷磨(Scrub)g-4 後烘烤(Postcure)H. 防焊(绿漆): (Solder Mask)h-1 C面印刷(Printing Top Side)h-2 S面印刷(Printing Bottom Side)h-3 静电喷涂(Spray Coating)h-4 前处理(Pretreatment)h-5 预烤(Precure)h-6 曝光(Exposure)h-7 显影(Develop)h-8 後烘烤(Postcure)h-9 UV烘烤(UV Cure)h-10 文字印刷( Printing of Legend )h-11 喷砂( Pumice)(Wet Blasting)h-12 印可剥离防焊(Peelable Solder Mask)I . 镀金Gold platingi-1 金手指镀镍金( Gold Finger )i-2 电镀软金(Soft Ni/Au Plating)i-3 浸镍金( Immersion Ni/Au) (Electroless Ni/Au)J. 喷锡(Hot Air Solder Leveling)j-1 水平喷锡(Horizontal Hot Air Solder Leveling)j-2 垂直喷锡( Vertical Hot Air Solder Leveling)j-3 超级焊锡(Super Solder )j-4. 印焊锡突点(Solder Bump)K. 成型(Profile)(Form)k-1 捞型(N/C Routing ) (Milling)k-2 模具冲(Punch)k-3 板面清洗烘烤(Cleaning & Backing)k-4 V型槽( V-Cut)(V-Scoring)k-5 金手指斜边( Beveling of G/F)L. 短断路测试(Electrical Testing) (Continuity & Insulation Testing)l-1 AOI 光学检查( AOI Inspection)l-2 VRS 目检(Verified & Repaired)l-3 泛用型治具测试(Universal Tester)l-4 专用治具测试(Dedicated Tester)l-5 飞针测试(Flying Probe)M. 终检( Final Visual Inspection)m-1 压板翘( Warpage Remove)m-2 X-OUT 印刷(X-Out Marking)m-3 包装及出货(Packing & shipping)m-4 目检( Visual Inspection)m-5 清洗及烘烤( Final Clean & Baking)m-6 护铜剂(ENTEK Cu-106A)(OSP)m-7 离子残余量测试(Ionic Contamination Test )(Cleanliness Test)m-8 冷热冲击试验(Thermal cycling Testing)m-9 焊锡性试验( Solderability Testing )N. 雷射钻孔(Laser Ablation)N-1 雷射钻Tooling孔(Laser ablation Tooling Hole)N-2 雷射曝光对位孔(Laser Ablation Registration Hole)N-3 雷射Mask制作(Laser Mask)N-4 雷射钻孔(Laser Ablation)N-5 AOI 检查及VRS ( AOI Inspection & Verified & Repaired)N-6 Blaser AOI (after Desmear and Microetching)N-7 除胶渣(Desmear)N-8 微蚀(Microetching )A/W (artwork) 底片Ablation 烧溶(laser),切除abrade 粗化abrasion resistance 耐磨性absorption 吸收ACC ( accept ) 允收accelerated corrosion test 加速腐蚀accelerated test 加速试验acceleration 速化反应accelerator 加速剂acceptable 允收activator 活化液active work in process 实际在制品adhesion 附着力adhesive method 黏着法air inclusion 气泡air knife 风刀amorphous change 不定形的改变amount 总量amylnitrite 硝基戊烷analyzer 分析仪anneal 回火annular ring 环状垫圈;孔环anode slime (sludge) 阳极泥anodizing 阳极处理AOI ( automatic optical inspection ) 自动光学检测applicable documents 引用之文件AQL sampling 允收水准抽样aqueous photoresist 液态光阻aspect ratio 纵横比(厚宽比) As received 到货时back lighting 背光back-up 垫板banked work in process 预留在制品base material 基材baseline performance 基准绩效batch 批beta backscattering 贝他射线照射法beveling 切斜边;斜边biaxial deformation 二方向之变形black-oxide 黑化blank controller 空白对照组blank panel 空板blanking 挖空blip 弹开blister 气泡;起泡blistering 气泡blow hole 吹孔board-thickness error 板厚错误bonding plies 黏结层bow ; bowing 板弯break out 从平环内破出bridging 搭桥;桥接BTO (Build To Order) 接单生产burning 烧焦burr 毛边(毛头) camcorder 一体型摄录放机carbide 碳化物carlson pin 定位梢carrier 载运剂catalyzing 催化catholic sputtering 阴极溅射法caul plate 隔板;钢板calibration system requirements 校验系统之各种要求center beam method 中心光束法central projection 集中式投射线certification 认证chamfer 倒角(金手指) chamfering 切斜边;倒角characteristic impedance 特性阻抗charge transfer overpotential 电量传递过电压chase 网框checkboard 棋盘chelator 蟹和剂chemical bond 化学键chemical vapor deposition 化学蒸着镀circumferential void 圆周性之孔破clad metal 包夹金属clean room 无尘室clearance 间隙coat 镀外表coating error 防焊覆盖错误coefficient of thermal expansion (CTE) 热澎胀系数cold solder joint 冷焊点cold-weld 金属粉末冷焊color 颜色color error 颜色错误compensation 补偿competitive performance 竞争力绩效complex salt 错化物complexor 错化物component hole 零件孔component side 零件面concentric 同心conformance 密贴性consumer products 消费性产品contact resistance 接触电阻continuous performance 连续发挥效能contract service 协力厂controlled split 均裂式conventional flow 乱流方式conventional tensile test 传统张力测试法conversion coating 转化层convex 突出coordinate list 资料清单copper claded laminates (CCL) 铜箔基板copper exposure 线路露铜copper mirror 镜铜copper pad 铜箔圆配copper residue (copper splash) 铜渣corrosion rate numbering 腐蚀速率计数系统corrosion resistance 抗蚀性coulombs law 库伦定律countersink 喇叭孔coupon 试样coupon location 试样点covering power 遮盖力CPU 中央处理器crack 破裂;裂痕crazing 裂痕;白斑cross linking 交联聚合cross talk 呼应作用crosslinking 交联crystal collection 结晶收集curing 聚合体current efficiency 电流效率cut-outs 挖空cutting 裁板cyanide 氰化物cycles of learning 学习循环cycle-time reduction 交期缩短date code 周期deburring 去毛头dedicated 专用型degradation 退变delamination 分层dent / pin hole 凹陷/ 针孔department of defense 国防部designation 字码简示法de-smear 除胶渣developing 显影dewetting 缩锡dewetting time 缩锡时间dimension error 外形尺寸错误dielectric constant 介质常数difficulty 困难度difunctional 双功能dimension 尺寸dimension stability 尺寸安定性dimensional stability 尺度安定性dimension and tolerance 尺寸与公差dirty hole 孔内异物discolor hole 孔黑;孔灰;氧化discoloration 变色disposable eyelet method 消耗性铆钉法distortion factor 尺寸变形函数double side 双面板downtime 停机时间drill 钻孔drill bit 钻头drill facet 钻尖切萷面drill pointer 钻尖重(研)磨机drilled blank board 已钻孔之裸板drilling 钻孔dry film 乾膜ductility 延展性economy of scale 经济规模edge spacing 板边空地edge-board contact ( gold finger ) 金手指efficiency 能量效率electric test 电测electrical testing 电测;测试electrochemical machine ECM 电化学加工法electrochemical reactor 电化学反应器electroforming 电铸electroless plate 化学铜electroless-deposition 无电镀electropolishing 电解抛光electrorefining 电解精链electrowinning 电解萃取elliptical set 椭圆形embrittlement 脆性entitlement performance 可达成绩效entrapment 电镀夹杂物epoxy 环氧树酯equipotential 电位线error data file 异常情形etch rate 蚀铜速率etchants 蚀刻液etchback 回蚀evaluation program 评估用程式exposure 曝光external pin method 外部插梢法eyelet hole 铆钉孔Eyeletting 铆眼fabric 网布failure 故障fast response 快速回应fault 瑕庛;缺陷fiber exposure 纤维显露fiber protrusion 纤维突出fiducial mark 光学点,基准记号filler 填充料film 底片filtration 过滤finished board 成品fixing 固着fixture 电测夹具(治具) flaking off 粹离flammability rating 燃性等级flare 喇叭形孔flat cable 并排电缆feedback loop 回馈循环first-in-first-out (FIFO) 先进先出flexible manufacturing system (FMS) 弹性制造系统flux 助焊剂foil distortion 铜层变形fold 空泡foreign include 异物foreign material 基材内异物free radical chain polymerization 自由基连锁聚合fully additive 加成法fully annealed type 彻底回火轫化之类形function 函数fundamental and basic 基本fungus resistance 抗霉性funnel flange 喇叭形摺翼galvanized 加法尼化制程gap 钻尖分开gauge length 有效长度gel time 胶化时间general resist ink 一般阻剂油墨general 通论general industrial 一般性(电子)工业级geometrical levelling 几何平整glass transition temperature (Tg) 玻璃态转换温度Gold 金gold finger 金手指gold plating 镀金golden board 标准板gouges 刷磨凹沟gouging 挖破grain boundary 金属晶体之四边green 绿色grip 夹头ground plane 接地层ground plane clearance 接地空环hackers 骇客HAL ( hot air leveling ) 喷锡haloing 白边;白圈hardener 硬化剂hardness 硬度hepa filter 空气滤清器high performance industrial 高性能(电子)工业级high reliability 高可靠度high resolution 高解析度high temperature elongation (HTE) 高温延展性铜箔high temperature epoxy (HTE) 高温树酯hit 击hole counter 数孔机hole diameter 孔径hole diameter error 孔径错误hole location 孔位hole number 孔数hole wall quality 孔壁品质hook 外弧hot dip 热浸法hull cell 哈氏槽hybrid 混成积体电路hydrogen bonding 氢键hydrolysis 水解hydrometallurgy 湿法冶金法image analysis system 影像分析系统image transfer 影像转移immersion gold 浸金(化镍金) immersion plating 浸镀法impedance 阻抗infrared reflow 红外线重熔inhibitor 热聚合抑制剂injection mold 射模ink 油墨innerlayer & outlayer 内外层insulation resistance 绝缘电阻intended position 应该在的位置intensifier 增强器intensity 强度inter molecular exchange 交互改变interconnection 互相连通ionic contaminants 离子性污染物ionic contamination testing 离子污染试验IPA 异丙醇inspiration (启蒙) identification 确认计划目标implementation 改善方案information 数据internalization 制度化invisible inventory 无形的库存knife edges 刀缘Knoop 努普(硬度单位) kraft paper 牛皮纸laminar flow 层流laminate 基层板laminating 压合lamination 压合laminator 压膜机land 焊垫lay back 刃角磨损lay up 组合叠板layout 布线;布局lead screw 牵引螺丝leakage 漏电learning curve 学习曲线legend 文字标记leveling 平整levelling additive 平整剂levelling power 平整力life support 维系生命limiting current 极限电流line space 线距line width 线宽linear variable differential transformer(LVDL) 线性可变差动转换器liquid 液状(态) liquid crystal resins 液晶树脂liquid photoimageable solder resist ink 液态感光防焊油墨liquid photoresist ink 液态光阻剂油墨lot size 批量lower carrier 底部承载板mechanical plating 机祴镀法machine scrub 刷磨清洁法macrothrowing power 巨分布力margin 钻头刃带market share 市场占有率marking error 文字错误masked leveling 儰装平整mass lamination 大型压板mass transfer 质量传送效应mass transfer overpotential 质量传递过电压mass transportation 质传master drawing 主图;蓝图material use factor 材料使用率mealing 泡点;白点memory 记忆装置meniscograph solderability measurement 新月型焊锡效果microetch 微蚀microetching 微蚀microfocus 微焦距microfocus system 微焦距系统microprofile 微表面microsectioning 微切片法microthrowing power 微分布力migration 迁移mini-tensile tester 迷你拉力测试仪mis hole location 孔位错误misregistration 焊锡面与零件面对位偏差misregsitration 对不准moisture and insulation resistance test 湿气与绝缘电阻试验molded circuit board (MCB) 模制电路板monoethanal amine 单乙醇氨monohydrate state 水化物monomer 单分子膜;单体mouse bite 锯齿;蚀刻缺口msec 毫秒muffle furnace 高温焚火炉multichip 超大IC型(多晶片模组) mylar 保护膜nail head 钉头NC drill 数位钻孔机negative etchback 反回蚀negative film 负片negative rake angle 负抠耙角network 回路;网路neutralization 中和nick 缺口nickel 镍nodule 铜瘤;瘤粒no flow resin 不流树脂noise 杂讯nominal 标示nominal dimension 标定长度nominal gel time 标示胶性时间nominal resin content 标示胶含量nominal resin flow 标示胶流量nominal scaled flow thickness 标示比例流量厚度OA equip 办公室自动化设备obsolescence factor 报废因素OEM 原设备制造商offset-list 补偿数据清单ohmmeter 欧姆计open 断路open circuits 断路open short testing 断短路测试opening 开口original art work (A/W) 原稿底片Others 其它outgrowth 增出over design 牛刀杀鸡overlap 钻尖重叠overlay entry 盖板overpotential 过电压oxidation 氧化oxide treatment 黑化处理oxided cytochrome 氧化性之细包色素oxygen evolution 氧气发生反应packed bed 充填床式pad 锡垫;圆配pad copper exposure pad 露铜panel 小型板面;母板panel plating 一次铜电镀parasitic 寄生的part no. 料号pattern plating 二次铜电镀PCB ( print circuit board ) 印刷电路板pcs 片peel strength 抗撕强度peeling off 剥离(剥落) performance specification 性能规范permittivity 透电率perspectives on experience 经验透视PET 聚酯photodiode detector 发光二极体侦测器photo initiator 感光启始剂photoresist 光阻phototool 光具(指工作底片) piece 子板面pinceton applied research 腐蚀测定仪pink ring 粉红圈pit 凹点pitch 脚距planar 平面plating 电镀plating exposure 下镀层露出plug gauge 插规plug hole 孔塞PNL (panel) 排板polar-polar interaction 极性之间的吸力polyester 聚酯类polyglycols 聚乙二醇polyimide 聚亚醯氨poor bevelling 磨边加工引起突起,剥离poor drill 孔形不良poor HAL 喷锡不良poor marking 字体不良poor pad 锡垫不良poor printed 印刷偏差poor solderability 焊锡性不良poor touch-up 补线不良position control system 位置控制系统positive rake angle 正抠耙角power curve model 幕次曲线模式practice 工艺惯例preferred 良好premature tearing 提前撕裂prepolymer 预聚合物prepreg 胶片pre-process ( front-end) 制前press 压床press cycle 压合周期primary current distribution 一次电流分布primary 主要product lifetimes 生命周期product process 制程promoter 促进剂protocal 初步资料prussic acid 普鲁士酸PTF-based process 厚膜糊法PTH (plating though hole) 导通孔pull away 拉开pumice 浮石粉pumice scrub 喷砂清洁法pyrometallurgy 火烧法冶链QC ( quality control) 品管QFP (quad flat pack ) 扁方型封装体qualification inspection 资格审查检验qualification testing 资格检定quality classification 品质等级quantitative 计量式测试rack 挂架radiometer 能量剂rake angle 抠耙角RAM [Random Access Memory 随机存取记忆体real time 关键时刻recessed trace process 凹槽线路法recovery tank 回收槽reduction 还原re-eninforcement 强化refraction 折光率reinforcement style 补强材料的型式register mark 对位用标记registration hole 对位孔registration pattern 长方形铜地REJ ( reject ) 退货;拒收rejectable 拒收release agent 脱模剂relief angle 浮离角remark 备注repair 修理resin content 树脂含量(胶含量) resin flow 胶流量resin flow percentage 树脂流量之百分率resin recession 树脂下陷resin smear 胶渣resist strippers 剥乾膜剂resistor network 排列电阻resolution 解像度return on assets 资产报酬率reversibility 可逆性rework 重工rosin 天然松香rotating cylinder 旋转圆柱形roughtness 孔壁粗糙;粗慥routing 切外形,成型routing bit 铣刀runout 偏转S/L on hole 孔内沾文字S/M ( solder mask ), S/L 防焊文字S/M (solder mask) 防焊S/M error 防焊种类错误S/M on hole 孔内绿漆salt spray test 盐水喷雾试验sampling size 抽样数scope 范围scored 刻痕scoring 枢槽;刮线scrap 废框scratches 刮伤screen printing 网版印刷scum 透明残膜sealing 封孔处理secondary 次要semi-additive 半加成法sensitize 敏化sensitizer 敏化液separator 钢隔板sequential lamination 渐成式压法serrated edges 毛边shatter 破碎short 短路shunt 分路silane treatment 矽烷处理silicone coupling agent 矽烷偶合剂silk screen 文字印刷simulator 模拟器single axis 单轴sizing 底片之伸缩补偿skip 漏印skip printing 跳印;漏印sliver 丝条slot 开槽slotting 开槽SMD ( surface mount device ) 表面黏着元件smear 胶渣SMT ( surface mount technology)表面黏着技术sodium carbonate monohydrate 结晶水碳酸钠soft tooling 软性工具solder 焊锡; 锡铅solder bridge 锡桥solder bump 锡突solder float 漂锡solder mask adhesion 绿漆附着力solder on G/F 金手指沾锡solder on trace 线路沾锡solder plug 锡塞solder side 焊锡面solderability 焊锡性solid carbide 实质碳化物spacing 间距spacing nonenough 间距不足SPC ( Statistical Process Control ) 统计生管specification 规范special considerations 特别考虑spin coating 旋转涂布spindle 钻轴spiral contractometer 螺旋收缩仪spot face 铣靶spray coating 喷涂Squeegee 刮刀stacking structure 叠板结构stamping 冲压standard hydraulic lamination 标准液压法standardizing 标准化starvation 缺胶step tablet 格片数stock option 认股选择权strain 应度strength 强度stressmeter 应力计subtractive 减除法surface convex 表面突起surface examination 表面检查surface insulation resistance (SIR) 表面绝缘电阻surface mount 表面黏着方式surface roughness 表面粗慥度surges 突波switch circuit 开关线路tab 金手指tack free 不黏taped hole gauge 锥形孔规target hole 靶孔task force 任务编组tensile strength 抗拉强度tensile stress 张性应力tent 浮盖terms and definitions 术语与定义termination load 抗匹配负载test circuit 测试线路test method 试验方法test point 测试点thermal shock 热震荡试验thermal stress 热应力试验thermistor 热电感应式thermo cycling 热循环试验theoretical cycle time 理论性周期时间thickness 厚度time to market 上市时机thickness distribution 厚度分布thief 补助阴极thin core 薄基板;内层板throwing power 分布力tolerance 公差;容差tooling hole 工具孔torque load 扭力拒之负载total quality program 全面的品质计划toughness 坚度trace error 线路错误trace nick & pin hole 线路缺口及针孔trace peeling 线路剥离trace pin-hole 线路针孔trace surface roughness 线路表面粗糙tarnish and oxide resist 抗污抗氧化剂transmittance 透光度trim line 裁切线true levelling 真平整true position 真正位置的孔;真位twist 板翘type 种类umbra 本影undercut 侧蚀uneven coating 喷锡厚镀不平整universal 万用型universal tensile tester 万用拉力试验机universal tester 泛用型测试机upper carrier 顶部承载钢uptime 稼动时间vacuum deposition 真空蒸镀法vacuum hydraulic lamination 真空液压法vaporizer 气化室V-cut V形槽vertical microsection 垂直微切片via hole 导通孔visible inventory 有形的库存vision inspection 目视检查V oid 孔破void in hole 孔壁上的破洞void in PTH hole 孔破walkman 随身听warehouse 仓库warp 板弯warp , warpage 板弯water absorption 吸水性wear resistance 耐磨度weave exposure 纤纹显露weave texture 织纹隐现wedge angle 契尖角week 周wet chemistry 湿式化学制程wet film 湿膜wet lamination 湿膜压膜法wet process 湿制程wetting 沾锡wetting balance 沾锡平衡法wicking 渗铜;渗入;灯蕊效应width 宽度width reduce 线细width-to-thickness ratio 宽度与厚度的比值window 操作范围work-in-process 在制品work order 工单working film 工作片working master 工作母片year 年yellow 金黄色yield 良率glassy state 玻璃状态rubbery state 橡胶状态trial & error 嚐试错误SOP 标准作业程序EDI (Exchange data interface) 资料交换介面FTP (file transfer protocol) 档案传送协定Web site 网址WAP (wireles application protocol) 无线应用协定series connection 串联parallel connection 并联NPI(new Product introduction) 新产品导入sample qualification 打样认可independent third party assessment 独立第三者评监internal assessment 户(内部)评监end product 完工产品rounding convention 四舍五入之惯例inspection lot 检验批target value 目标值horizontal microsection 水平切片order of precedence 优先顺序master drawing 主图making ink 文字油墨thermal plane 散热层hole-fill insulation material 填孔用绝缘物unsupported holes 非电镀通孔hole pattern accuracy 孔位准度dielectric layer thickness 介质层厚度lifted lands 焊垫浮起nail-heading 钉头Plating folds 电镀皱折tackness 沾黏性sample size 样本数sampling plan 抽样计划rejected lots 拒收批exterior containers 外箱intended use 主要用途non-flow (no-flow) 非流性etchback (when specified) 回蚀(当指定时才做)abrade 动擦掉;擦伤;磨损abrasion 名擦破;擦伤;磨灭;剥蚀abridge 动缩短;省略;抄录;缩减;剥夺absorbent 形会吸收的;有吸收力的absorbent cotton 形脱脂棉absorption 名吸收;专心;合并abstract 形抽象的;理论的;不专心动摘录;抽象;偷;转移提炼;抽取abuse 动滥用;误用;咒骂;虐待;欺骗acceleration 名加速[度];促进access 名接近;接受;会面;捷径;通路accessory 形附属的;补助的;从犯的accommodate 动调节;和解;供应;留;容纳accordance 名一致;调和account 名计算;会计;报告;解释;理由accredit 动相信;认定资格;归功於.. accumulation 名累积;堆积accurate 形正确的;准确的;精密的accurately 副正确地;精密地acetone 名丙酮[挥发性无色液体achieve 动完成;成就;博得;达到[目的] acid 形酸的;不和悦的;不开心的acknowledge 动认;承认;自白;感谢acknowledgment 名承认;容许名自白;谢礼;礼物;收帖;收条;感谢acoustical 形听觉的;音响学的acrylic 形压克力的;丙烯酸的activate 动使活动;催化;净化;编组activation 名使活动;使催[活]化;活化activator 名使活跃之物;催化剂active 形活动[泼]的;勤勉的;主动的;动态acuity 名锐敏;激烈;苛刻acupuncture 名针灸;针治acute (angle) 形尖锐的;精明的;激烈的;高音的;(锐角)added value 名附加价值addendum 名补遗[书的]附册;附加物additive 形该加的;加法的;加法的名电池等的]添加剂address 名称呼;住址;致辞;谈吐;请求动演说;申请;免法官之职;说服;追求adequacy 名适当;妥当;足够adhere 动黏着;附着;固执;信奉;支持adherence 名固执;固守;黏着;附着adherent 形黏着的;附着於;信奉的名支持者;伙伴adhesion 名黏着;胶着;固执;瘉合adjacency 名邻接[物;地];前後节目adjacent 形邻近的;邻接的;附近的administrate 动管理;支配administration 名管理;经营名当局;政府;内阁;给与;配药;遗产[财政]管理administrative 形管理行政的adopted 形被收养的;被采用的adoption 名采用;收养;过继;公认advantage 名利益;便利;优势;优越adversely 副逆地;反对地;不利地advisory 形劝告的;建议的;忠告的aesthetics 名美学affected 形受影响的;感染的;感动的affiliation 名加入;同盟;协力名私生子父亲认定;追溯由来;关系;养父子关系affinity 名姻亲;同族关系;亲近性名远缘份;嗜好;相处得来的人;亲和力affirm 动断言;确定;肯定;断定;确认affix 动附加;贴上;签上;盖上;使负责against 名对,对着;反对;相逆;依;靠agar 名海菜;紫菜;石花菜;细菌培养基agenda 名会议事项;议事日程;议程agent 名代理者;管理人;代办人名行为者;手下;作因;天然力;官员;推销员agglomeration 名结块;凝结aggravating 形使..恶化的;可恼的aggregate 动聚集;总计;集合;合计的名集合;集团;集合体;材料aggressive 形侵略的;攻势的;挑衅的形气势汹汹的;进取[积极]的;精力旺盛的aging 形上年纪的;变老的;变旧的;老化agitation 名搅动;动摇;兴奋;煽动agreement 名契约;协议;符合;同意air force 名空军alcohol 名酒精;醇;酒;饮酒algorithm 名互除法align 动使成一线;排成一行;排列;合作alignment 名排成直线;整顿;合作aliquot 形能整除[某数的数] alkaline 形硷属的;硷性的alkalinity 名硷度alleviate 动减轻[痛苦];缓和allocate 动分派;配置;定位置;分配allow 动允许;听任;给与;斟酌;扣除;想allowance 名津贴;零用金;宽限;斟酌名扣除;许可;承认;折让;发津贴;给与定量alloy 名合金;成色;贱金属;混合物动使成合金;减低成色;减少;成合金;搀杂alpha 名希腊字母首字;最初alter 动改变;改造;改作;阉割;去势;变alteration 名变更;改造alternate 形交互的;间隔的;代理人动交错陈列;交替;轮流;交流作用alternative 形二中择一的altitude 名高;高度;海拔高度;高处aluminum 名铝[金属元素] ambient 形包围的ambiguous 形暧昧的;不明确的ambition 名雄心;热望;野心的目标(志)amide 名氨基化合物ammonia 名氨[气体];氨水ammoniacal 形氨的;氨性的;含氨的amperage 名安培数amplitude 名广阔;宽;丰富;充足名振幅;射程;[天体的]出没方位角analog 名类似物;相似体;类比analogy 名类似;相似;类推anchor 名锚;殿後者;锚纹饰;凿;急煞车anchoring spur 名着力爪angstrom 名埃[光的波长单位] angular 形有角[棱]的;尖的;瘦的;笨anion 名阴离子anneal 动加热後退火使其韧化;锻练;(回火);轫化annex 动附加;追加;并吞;罢占;侵吞名加添物;附册;附件;加建建筑;别馆annotate 动注解[书等];注释annual 形一年的;每年的;一年生的名一年生植物;年刊书[志];年报;年监annular 形环状的;轮状的annuli .. annulus的复数形anode 名正极;阳极anomaly 名不规则;反常;近点离角antimony 名锑[金属元素] apparatus 名[一套]器具;器官;构造apparent 形显而易见的;外表上的appendix 名附属物;附录;追加;盲肠applicable 形可适用的;能应用的apply 动适用;应用;抚;贴;涂;敷;使用appraisal 名评价;估价;监定approach 动接近;近似;向..交涉;研讨名接近;近似;入口;[研究]门径;亲近;逼近appropriate 动作为专用;挪用形适当的;特有的;固有的apron 名围巾;围嘴;马车挡雨的遮脚布名法衣;前舞台;飞机库前柏油或水泥地;护岸aqueous 形水的;水般的;水成的archives 名公文保管处;挡案;公文arise 动起来;出现;兴起;发生;起立;起arithmetic 名算术;算法;计算army 名军队;陆军;大群;团体arose .. arise的过去式array 名打扮;排队;列举;召集;军势;衣裳ascertain 动确定;稽考;探查aspect 名样子;光景;容貌;脸相;方向名方位;面;局面;情势;[星]视座;相;态asphalt 名沥青;铺装用柏油asphaltic 形柏油的aspire 动热望;怀大志;切望;高耸assembly 名集会;会合;会议;组合assess 动估定;评价;估价;课税;徵收assessment 名估定;评价;课徵;会费assets 名财产[可作偿债者];资产assets and liabilities 名资产与负债assignment 名分配;转让;任务assist 动援助;出席;[棒球]补杀assistance 名援助;帮助assistant 名助手;助理;店员associated 形联合的;关联的assume 动采取;承担;假装;臆测;摆架子assumption 名采取;承担;假定;傲慢asymmetric 形不均匀的;不对称的atmosphere 名大气;情况;环境;气氛atomizer 名喷雾器;香水喷雾器attachment 名附着;固着;附着物名附属品;依恋;执着;逮补;拘留attack 动攻击;袭击;害病;动手attempt 动尝试;企图;窥伺;袭击;未遂attendant 形跟随的;出席的;伴随的名陪从;随员;伴随物;从业者;管理员;加油站的站员attenuate 动使变稀薄;使变细;弄淡attenuation 名[使]变薄;稀薄化attestation 名证据;证言;证明attitude 名姿势;身段;态度;心意attribute 动归因;认为是..的缘故名属性;特质;附属物;象徵;形容词;属性attribution 名归属;归因;属性attributive 形属性的;形容的;修饰语audience 名听众;观众;收听者;收看者audit 名审计;审核;查帐;决算;旁听aurum 名金[金属元素] authorization 名授权;委任;认可autoclave 名快锅之一种auxiliary 形补助的;副的;预备的名帮助者;补助物;外国补助部队;补助舰;助动avenue 名林荫路;林荫道;大路;门径aware 形知道;晓得;注意到awareness 名知道;晓得;注意axial 形轴的;成轴的;轴周围的backlight 名背光; backup名支援;滞销货;阻塞;背板;备份backward 副向後;相反;以前形向後;落後;怕羞的baggy 形袋状的;宽松而下垂的balance 动秤;抵消;均衡;踌躇名秤;对称;比较;剩余;(可指尾数板) balance due 名不足额balance in hand 名余款bar 名染;妨害;禁止;反对;除..之外名棒;闩;线条;法院;节线bar code 名条码barometric 形气压[计]的barrel 名桶;枪身;选举费用basket 形篮制的;自备的野餐名篮篓;一篮;篮形的东西bat 名球棒;打手;片;棉絮;蝙蝠动速写;充分讨论;轮到打击batch 名一炉[面包等];一组bath 名沐浴;温泉地;浸渍用水battery 名殴打;电池;投捕手Baume scale 名波美(比重计)beaker 名有倒口的烧杯;大杯beam 动放射;闪亮;微笑;广播名梁;船幅;秤杆;杠杆;光线behavior 名规矩;品行;作用bellow(s) 动怒吼;咆哮;呼啸;(风箱(名) bend 动弯;拉;使屈服;倾心beneath 副在..之下;比..差beneficiary 形享受俸禄;臣服的名受益人;公费生benefit 动有益;享受利益;受益名利益;恩惠;义演;给付bevel 名斜角;倾斜;斜面;斜角规动截成斜角;斜切bias 动使存偏见;使偏袒;斜的;交叉的bias 名斜线;成见;倾向;歪斜;偏见bifurcate 动分[成]叉bilateral 形两边;有两面的binary 名二要素合成物;双子星形两要素的;二进位的;二元的binder 名装订人;使固定的东西;黏结剂bipolar 形有两极的;双极的blade 名叶;刃;剑术家;扁平;翼名荡子;女子;舌的前端blank 形空白的;单调的;完全的;无效的名空虚;钥匙;空包弹;标准杆孔规bleed 名切印刷部份的页次动流血;流出树液;取血;搾bleeder 名易出血或不止的人blend 名混合;混合物;混成语;溶合blender 名混合;混合器;搅拌器;果菜榨汁机blind 动使失去判断;隐蔽形瞎的;鲁莽的;不完全的;遮眼物;欺瞒blip 名雷达映出的影像blister 名水泡;发泡膏;枪座;使烦恼blob 名滴;小斑点;零分;溅block 名石头;切肉板;滑车;妨碍;占地方;一区blot 名污痕;棋子;弱点动抹脏;涂掉;吸乾;遮盖blotting 名乾印(印刷洗纸)blunt 动弄钝;减弱;变钝名短粗的针;现金;钝的;粗鲁;生硬;率直的blur 名污脏;蒙胧;不清楚;污名动弄脏;使模糊;朦胧blurr 动弄脏;使模糊;朦胧blurry 形模糊的;不清楚的;污斑blush 名面赤;红;赤色;一瞥动害羞;脸红;弄红;使面红bolt 名挺直;跑开;脱党;细看名箭头;电光;拒绝;螺钉bomb 动丢炸弹;轰炸名炸弹;手榴弹;突发事件bond 名结合;契约;证券;保证人形黏土的;被囚禁的booklet 名小册子;印刷品boost 动由後推;推上;援助;声援boot 动用靴踢;使穿长靴;电脑开机;起动名靴;放行李处;刑具;利益borderline 名边界[上的]bound 名境界[线];领域;边际动跳;使弹回;bind的过去形被缚的;装订的;决意的bow 名弓;弯曲;蝴蝶结;桨动鞠躬;屈服;向导;使屈服branch 名枝;分枝;支线;分部brand 动打烙印;予以深刻印象名品种;商标;烙印;污名brass 名厚脸皮;高级军官;黄铜[制品]break 动弄伤;违背;断;使破产;损坏;闯入名破晓;跑出;阻断;小憩break-away 名折断边breakdown 名故障;挫折;分类;分析名崩溃;倒塌;破损breaker 名碎波;破碎者;切断机名驯马师;[饮料用]水桶breakover 名崩溃breath 名气息;呼吸;低语;微吹brighten 动使辉煌;使快活;使聪brightener 名光泽剂bristle 名刚毛;猪鬃动使竖立毛发;发怒brittle 形易碎的;短暂的broadly 副宽广地;明白地;无礼bromide 名溴化物bronze 名青铜[色;制品];古铜browse 动吃嫩叶;放牧;浏览名嫩叶;嫩芽;嫩枝brush 名小冲突;丛林灌木地带名刷;笔;笔法;狐尾;拂拭bubble 名泡;泡沫;诈欺buckle 动扣住;弯曲;起皱;扣紧名扣子;弯曲;皱bud 名芽;花蕾;未发育的;少女;开始发育buffer 名缓冲器;减弱冲突的人bug 名毛病;故障;缺点;错误名半翅类的虫;病菌;虫动装置防盗铃[秘密扩音器] bulge 名胀;腰;凸出部份;优越bull 名公牛;金牛座;买空者名警察;吹牛;靶心;傻事bump 名碰撞声音;肿块;摇;扑通动冲撞;碰;交替;免职;颠簸buoyancy 名轻快;乐观;浮力bureau 名衣屉柜[大桌];办公室buret 名滴管;玻璃量管burn 动烧;灼伤;铭感;腐蚀;焦虑burner 名灯口;烧火的;燃烧器burnish 名光辉;光泽动磨;光;光亮;发光burnout 名燃料烧尽;烧坏burr 名光圈;隆隆声;喉音;钻孔器;磨刀石bury 动埋葬;葬礼;埋藏;掩蔽busses .. bus的复数bypass 名旁管;迂回路;忽视;旁路cabinet 名小柜橱;会议室;内阁calcium 名钙[金属元素] calculate 动计算;预测;指望calibration 名口径测定;查刻度calipers 名测径器calorimetry 名热量测定cam 名凸轮camber 名上弯形[道路];弧形cancellation 名抹消;取消;解除cannister 名罐;茶筒;滤毒罐cant 名哀诉声;伪善的口吻;黑话;隐语名口号;时髦话;倾斜;斜角;一堆;一滚cap 名无边帽;头巾;选手;鞘;套;柱头;雷管名最高部;修过的轮胎的轮底;临时参加费capable 形有能力的;可以..的capacitance 名[传导体的]容量capillary 形毛的;毛细管capital 形首位的;主要的;根本的形优秀的;罪大恶极的;致命的;严重的;上好的capital 名首都;大写;资本;本钱;柱头captive 名俘虏;迷恋;被囚的;专有的capture 名捕获;被捕获者carbide 名碳化物;碳化钙carbonate 动使成碳酸盐;碳化carriage 名车;搬运;姿势;风度carrier 名运送人;信差;搬运器名带菌者;航空母舰;介质;载波;货架cash 名钱;现金;小额货币cash 动兑现;付现款cashflow 名现金流量catalyst 名触媒剂category 名种类;部属;类目caterpillar 名毛虫;履带车辆cathode 名阴极cation 名阳离子;阴向游子caul (plate) 名网膜;羊膜囊;发网;(隔板) caution 名小心;警戒;警告;担保;吃惊cautiously 副谨慎地;小心地cavitation 名[螺旋桨後的]涡卷;半真空;空泡化cavity 名空穴;空窝;腔;蛀牙洞CCD 名电眼cease 动终止;停顿;停止cell 名小室;密室;茅舍;小屋;墓;渗透者名囊;蜂窝;窝;细胞;电池cellophane 名玻璃纸cellular 形细胞的;划分的cellular phone 名大哥大行动电话cellulose 名纤维素Celsius 名(度) C (*) centrifugal 形离心的;离心力的centrifuge 名离心分离机centripetal 形向心(性)的ceramics 名窑业;制陶业;陶器certification 名证明;检定certified 形被证明的;有保证的chalk 动用粉笔记;白粉擦;记录名粉笔;白粉;记帐出售;众所珍爱的马challenge 名挑战;难题;盘问chamber 名室;会议场;便壶;窝动作房间用;关在室内;上膛。
PCB专业术语
一、综合词汇CAM(computer Aided Manufacturing1、印制电路：printed circuit2、印制线路：printed wiring3、印制板：printed board4、印制板电路：printed circuit board (pcb)5、印制线路板：printed wiring board(pwb)6、印制元件：printed component7、印制接点：printed contact8、印制板装配：printed board assembly9、板：board10、单面印制板：single-sided printed board(ssb)11、双面印制板：double-sided printed board(dsb)12、多层印制板：mulitlayer printed board(mlb)13、多层印制电路板：mulitlayer printed circuit board14、多层印制线路板：mulitlayer prited wiring board15、刚性印制板：rigid printed board16、刚性单面印制板：rigid single-sided printed borad17、刚性双面印制板：rigid double-sided printed borad18、刚性多层印制板：rigid multilayer printed board19、挠性多层印制板：flexible multilayer printed board20、挠性印制板：flexible printed board21、挠性单面印制板：flexible single-sided printed board22、挠性双面印制板：flexible double-sided printed board23、挠性印制电路：flexible printed circuit (fpc)24、挠性印制线路：flexible printed wiring25、刚性印制板：flex-rigid printed board, rigid-flex printed board26、刚性双面印制板：flex-rigid double-sided printed board, rigid-flex double-sided printed27、刚性多层印制板：flex-rigid multilayer printed board, rigid-flex multilayer printed board28、齐平印制板：flush printed board29、金属芯印制板：metal core printed board30、金属基印制板：metal base printed board31、多重布线印制板：mulit-wiring printed board32、陶瓷印制板：ceramic substrate printed board33、导电胶印制板：electroconductive paste printed board34、模塑电路板：molded circuit board35、模压印制板：stamped printed wiring board36、顺序层压多层印制板：sequentially-laminated mulitlayer37、散线印制板：discrete wiring board38、微线印制板：micro wire board39、积层印制板：buile-up printed board40、积层多层印制板：build-up mulitlayer printed board (bum)41、积层挠印制板：build-up flexible printed board42、表面层合电路板：surface laminar circuit (slc)43、埋入凸块连印制板：b2it printed board44、多层膜基板：multi-layered film substrate(mfs)45、层间全内导通多层印制板：alivh multilayer printed board46、载芯片板：chip on board (cob)47、埋电阻板：buried resistance board48、母板：mother board49、子板：daughter board50、背板：backplane51、裸板：bare board52、键盘板夹心板：copper-invar-copper board53、动态挠性板：dynamic flex board54、静态挠性板：static flex board55、可断拼板：break-away planel56、电缆：cable57、挠性扁平电缆：flexible flat cable (ffc)58、薄膜开关：membrane switch59、混合电路：hybrid circuit60、厚膜：thick film61、厚膜电路：thick film circuit62、薄膜：thin film63、薄膜混合电路：thin film hybrid circuit64、互连：interconnection65、导线：conductor trace line66、齐平导线：flush conductor67、传输线：transmission line68、跨交：crossover69、板边插头：edge-board contact70、增强板：stiffener71、基底：substrate72、基板面：real estate73、导线面：conductor side74、元件面：component side75、焊接面：solder side76、印制：printing77、网格：grid78、图形：pattern79、导电图形：conductive pattern80、非导电图形：non-conductive pattern81、字符：legend82、标志：mark二、基材：1、基材：base material2、层压板：laminate3、覆金属箔基材：metal-clad bade material4、覆铜箔层压板：copper-clad laminate (ccl)5、单面覆铜箔层压板：single-sided copper-clad laminate6、双面覆铜箔层压板：double-sided copper-clad laminate7、复合层压板：composite laminate8、薄层压板：thin laminate9、金属芯覆铜箔层压板：metal core copper-clad laminate10、金属基覆铜层压板：metal base copper-clad laminate11、挠性覆铜箔绝缘薄膜：flexible copper-clad dielectric film12、基体材料：basis material13、预浸材料：prepreg14、粘结片：bonding sheet15、预浸粘结片：preimpregnated bonding sheer16、环氧玻璃基板：epoxy glass substrate17、加成法用层压板：laminate for additive process18、预制内层覆箔板：mass lamination panel19、内层芯板：core material20、催化板材：catalyzed board ,coated catalyzed laminate21、涂胶催化层压板：adhesive-coated catalyzed laminate22、涂胶无催层压板：adhesive-coated uncatalyzed laminate23、粘结层：bonding layer24、粘结膜：film adhesive25、涂胶粘剂绝缘薄膜：adhesive coated dielectric film26、无支撑胶粘剂膜：unsupported adhesive film27、覆盖层：cover layer (cover lay)28、增强板材：stiffener material29、铜箔面：copper-clad surface30、去铜箔面：foil removal surface31、层压板面：unclad laminate surface32、基膜面：base film surface33、胶粘剂面：adhesive faec34、原始光洁面：plate finish35、粗面：matt finish36、纵向：length wise direction37、模向：cross wise direction38、剪切板：cut to size panel39、酚醛纸质覆铜箔板：phenolic cellulose paper copper-clad laminates(phenolic/paper ccl)40、环氧纸质覆铜箔板：epoxide cellulose paper copper-clad laminates (epoxy/paper ccl)41、环氧玻璃布基覆铜箔板：epoxide woven glass fabric copper-clad laminates42、环氧玻璃布纸复合覆铜箔板：epoxide cellulose paper core, glass cloth surfaces copper-clad laminates43、环氧玻璃布玻璃纤维复合覆铜箔板：epoxide non woven/woven glass reinforced copper-clad laminates44、聚酯玻璃布覆铜箔板：ployester woven glass fabric copper-clad laminates45、聚酰亚胺玻璃布覆铜箔板：polyimide woven glass fabric copper-clad laminates46、双马来酰亚胺三嗪环氧玻璃布覆铜箔板：bismaleimide/triazine/epoxide woven glass fabric copper-clad lamimates47、环氧合成纤维布覆铜箔板：epoxide synthetic fiber fabric copper-clad laminates48、聚四乙烯玻璃纤维覆铜箔板：teflon/fiber glass copper-clad laminates49、超薄型层压板：ultra thin laminate50、陶瓷基覆铜箔板：ceramics base copper-clad laminates51、紫外线阻挡型覆铜箔板：uv blocking copper-clad laminates三、基材的材料1、a阶树脂：a-stage resin2、b阶树脂：b-stage resin3、c阶树脂：c-stage resin4、环氧树脂：epoxy resin5、酚醛树脂：phenolic resin6、聚酯树脂：polyester resin7、聚酰亚胺树脂：polyimide resin8、双马来酰亚胺三嗪树脂：bismaleimide-triazine resin9、丙烯酸树脂：acrylic resin10、三聚氰胺甲醛树脂：melamine formaldehyde resin11、多官能环氧树脂：polyfunctional epoxy resin12、溴化环氧树脂：brominated epoxy resin13、环氧酚醛：epoxy novolac14、氟树脂：fluroresin15、硅树脂：silicone resin16、硅烷：silane17、聚合物：polymer18、无定形聚合物：amorphous polymer19、结晶现象：crystalline polamer20、双晶现象：dimorphism21、共聚物：copolymer22、合成树脂：synthetic23、热固性树脂：thermosetting resin24、热塑性树脂：thermoplastic resin25、感光性树脂：photosensitive resin26、环氧当量：weight per epoxy equivalent (wpe)27、环氧值：epoxy value28、双氰胺：dicyandiamide29、粘结剂：binder30、胶粘剂：adesive31、固化剂：curing agent32、阻燃剂：flame retardant33、遮光剂：opaquer34、增塑剂：plasticizers35、不饱和聚酯：unsatuiated polyester36、聚酯薄膜：polyester37、聚酰亚胺薄膜：polyimide film (pi)38、聚四氟乙烯：polytetrafluoetylene (ptfe)39、聚全氟乙烯丙烯薄膜：perfluorinated ethylene-propylene copolymer film (fep)40、增强材料：reinforcing material41、玻璃纤维：glass fiber42、e玻璃纤维：e-glass fibre43、d玻璃纤维：d-glass fibre44、s玻璃纤维：s-glass fibre45、玻璃布：glass fabric46、非织布：non-woven fabric47、玻璃纤维垫：glass mats48、纱线：yarn 49、单丝：filament50、绞股：strand51、纬纱：weft yarn52、经纱：warp yarn53、但尼尔：denier54、经向：warp-wise55、纬向：weft-wise, filling-wise56、织物经纬密度：thread count57、织物组织：weave structure58、平纹组织：plain structure59、坏布：grey fabric60、稀松织物：woven scrim61、弓纬：bow of weave62、断经：end missing63、缺纬：mis-picks64、纬斜：bias65、折痕：crease66、云织：waviness67、鱼眼：fish eye68、毛圈长：feather length69、厚薄段：mark70、裂缝：split71、捻度：twist of yarn72、浸润剂含量：size content73、浸润剂残留量：size residue74、处理剂含量：finish level75、浸润剂：size76、偶联剂：couplint agent77、处理织物：finished fabric78、聚酰胺纤维：polyarmide fiber79、聚酯纤维非织布：non-woven polyester fabric80、浸渍绝缘纵纸：impregnating insulation paper81、聚芳酰胺纤维纸：aromatic polyamide paper82、断裂长：breaking length83、吸水高度：height of capillary rise84、湿强度保留率：wet strength retention85、白度：whitenness86、陶瓷：ceramics87、导电箔：conductive foil88、铜箔：copper foil89、电解铜箔：electrodeposited copper foil (ed copper foil)90、压延铜箔：rolled copper foil91、退火铜箔：annealed copper foil92、压延退火铜箔：rolled annealed copper foil (ra copper foil)93、薄铜箔：thin copper foil94、涂胶铜箔：adhesive coated foil95、涂胶脂铜箔：resin coated copper foil (rcc)96、复合金属箔：composite metallic material97、载体箔：carrier foil98、殷瓦：invar99、箔（剖面）轮廓：foil profile100、光面：shiny side101、粗糙面：matte side102、处理面：treated side103、防锈处理：stain proofing104、双面处理铜箔：double treated foil四、设计1、原理图：shematic diagram2、逻辑图：logic diagram3、印制线路布设：printed wire layout4、布设总图：master drawing5、可制造性设计：design-for-manufacturability6、计算机辅助设计：computer-aided design.(cad)7、计算机辅助制造：computer-aided manufacturing.(cam)8、计算机集成制造：computer integrat manufacturing.(cim)9、计算机辅助工程：computer-aided engineering.(cae)10、计算机辅助测试：computer-aided test.(cat)11、电子设计自动化：electric design automation .(eda)12、工程设计自动化：engineering design automaton .(eda2)13、组装设计自动化：assembly aided architectural design. (aaad)14、计算机辅助制图：computer aided drawing15、计算机控制显示：computer controlled display .(ccd)16、布局：placement17、布线：routing18、布图设计：layout19、重布：rerouting20、模拟：simulation21、逻辑模拟：logic simulation22、电路模拟：circit simulation23、时序模拟：timing simulation24、模块化：modularization25、布线完成率：layout effeciency26、机器描述格式：machine descripttionm format .(mdf)27、机器描述格式数据库：mdf databse28、设计数据库：design database29、设计原点：design origin30、优化（设计）：optimization (design)31、供设计优化坐标轴：predominant axis32、表格原点：table origin33、镜像：mirroring34、驱动文件：drive file35、中间文件：intermediate file36、制造文件：manufacturing documentation37、队列支撑数据库：queue support database38、元件安置：component positioning39、图形显示：graphics dispaly40、比例因子：scaling factor41、扫描填充：scan filling42、矩形填充：rectangle filling43、填充域：region filling44、实体设计：physical design45、逻辑设计：logic design46、逻辑电路：logic circuit47、层次设计：hierarchical design48、自顶向下设计：top-down design49、自底向上设计：bottom-up design50、线网：net51、数字化：digitzing52、设计规则检查：design rule checking53、走（布）线器：router (cad)54、网络表：net list55、计算机辅助电路分析：computer-aided circuit analysis56、子线网：subnet57、目标函数：objective function58、设计后处理：post design processing (pdp)59、交互式制图设计：interactive drawing design60、费用矩阵：cost metrix61、工程图：engineering drawing62、方块框图：block diagram63、迷宫：moze64、元件密度：component density65、巡回售货员问题：traveling salesman problem66、自由度：degrees freedom67、入度：out going degree68、出度：incoming degree69、曼哈顿距离：manhatton distance70、欧几里德距离：euclidean distance71、网络：network72、阵列：array73、段：segment74、逻辑：logic75、逻辑设计自动化：logic design automation76、分线：separated time77、分层：separated layer78、定顺序：definite sequence五、形状与尺寸：1、导线（通道）：conduction (track)2、导线（体）宽度：conductor width3、导线距离：conductor spacing4、导线层：conductor layer5、导线宽度/间距：conductor line/space6、第一导线层：conductor layer no.17、圆形盘：round pad8、方形盘：square pad9、菱形盘：diamond pad10、长方形焊盘：oblong pad11、子弹形盘：bullet pad12、泪滴盘：teardrop pad13、雪人盘：snowman pad14、v形盘：v-shaped pad15、环形盘：annular pad16、非圆形盘：non-circular pad17、隔离盘：isolation pad18、非功能连接盘：monfunctional pad19、偏置连接盘：offset land20、腹（背）裸盘：back-bard land21、盘址：anchoring spaur22、连接盘图形：land pattern23、连接盘网格阵列：land grid array24、孔环：annular ring25、元件孔：component hole26、安装孔：mounting hole27、支撑孔：supported hole28、非支撑孔：unsupported hole29、导通孔：via30、镀通孔：plated through hole (pth)31、余隙孔：access hole32、盲孔：blind via (hole)33、埋孔：buried via hole34、埋/盲孔：buried /blind via35、任意层内部导通孔：any layer inner via hole (alivh)36、全部钻孔：all drilled hole37、定位孔：toaling hole38、无连接盘孔：landless hole39、中间孔：interstitial hole40、无连接盘导通孔：landless via hole41、引导孔：pilot hole42、端接全隙孔：terminal clearomee hole43、准表面间镀覆孔：quasi-interfacing plated-through hole44、准尺寸孔：dimensioned hole45、在连接盘中导通孔：via-in-pad46、孔位：hole location47、孔密度：hole density48、孔图：hole pattern49、钻孔图：drill drawing50、装配图：assembly drawing51、印制板组装图：printed board assembly drawing52、参考基准：datum referance电路板术语总整理*****A*****Abietic Acid松脂酸.Abrasion Resistance耐磨性.Abrasives磨料,刷材.ABS树脂.Absorption吸收(入).Ac Impedance交流阻抗.Accelerated Test(Aging)加速老化(试验).Acceleration速化反应.Accelerator 加速剂,速化剂.Acceptability,Acceptance 允收性,允收.Access Hole露出孔,穿露孔.Accuracy准确度.Acid Number (Acid Value)酸值.Acoustic Microscope (AM)感音成像显微镜.Acrylic压克力(聚丙烯酸树脂).Actinic Light (or Intensity, or Radiation)有效光.Activation活化.Activator活化剂.Active Carbon活性炭.Active Parts(Devices)主动零件.Acutance解像锐利度.Addition Agent添加剂.Additive Process加成法.Adhesion附着力.Adhesion Promotor附着力促进剂.Adhesive胶类或接着剂.Admittance导纳(阻抗的倒数).Aerosol喷雾剂,气熔胶,气悬体.Aging老化.Air Inclusion气泡夹杂.Air Knife风刀.Algorithm算法.Aliphatic Solvent脂肪族溶剂.Aluminium Nitride(AlN)氮化铝.Ambient Tamp环境温度.Amorphous无定形,非晶形.Amp-Hour安培小时.Analog Circuit/Analog Signal模拟电路/模拟讯号. Anchoring Spurs着力爪.Angle of Contack接触角.Angle of Attack攻角.Anion阴离子.Anisotropic异向性,单向的.Anneal 韧化(退火).Annular Ring孔环.Anode阳极.Anode Sludge阳极泥.Anodizing阳极化.ANSI美国标准协会.Anti-Foaming Agent消泡剂.Anti-pit Agent抗凹剂.AOI自动光学检验.Apertures开口,钢版开口.AQL品质允收水准.AQL(Acceptable Quality Level)允收品质水准. Aramid Fiber聚醯胺纤维.Arc Resistance耐电弧性.Array排列.Artwork底片.ASIC特定用途绩体电路器.Aspect Ratio纵横比.Assembly组装装配.A-stage A阶段.ATE自动电测设备.Attenuation讯号衰减.Autoclave压力锅.Axial-lead轴心引脚.Azeotrope共沸混合液.*****B*****Back Light (Back Lighting)背光法.Back Taper反锥斜角.Backpanels, Backplanes支撑板.Back-up 垫板.Balanced Transmission Lines平衡式传输线.Ball Grid Array球脚数组(封装).Bandability弯曲性.Banking Agent护岸剂.Bare Chip Assembly裸体芯片组装.Barrel孔壁,滚镀.Base Material基材.Basic Grid基本方格.Batch批.Baume波美度(凡液体比重比水重则Be=145-(145÷Sp.Gr) 凡液体比重比水轻则Be=140÷(Sp.Gr-130)*Sp.Gr 为比重即同体绩物质对"纯水"1g/cm的比值). Beam lead光芒式的平行密集引脚.Bed-of-Nail Testing针床测试.Bellows Conact弹片式接触.Beta Ray Backscatter贝他射线反弹散射.Bevelling切斜边.Bias斜张纲布,斜纤法.Bi-Level Stencil]双阶式钢板.Binder粘结剂.Bits头(Drill Bits).Black Oxide黑氧化层.Blanking冲空断开.Bleack 漂洗.Bleeding溢流.Blind Via Hole肓通孔.Blister局部性分层或起泡.Block Diagram电路系统块图 .Blockout封纲.Blotting干印.Blotting Paper吸水纸.Blow Hole吹孔.Blue Plaque蓝纹(锡面钝化层).Blur Edge (Circle)模糊边带(圈). Bomb Sight弹标.Bond Strength结合强度. Bondability结合性.Bonding Layer结合层接着层. Bonding Sheet(Layer)接合片. Bonding Wire结合线.Bow, Bowing板弯.Braid编线.Brazing硬焊(用含银的铜锌合金焊条). 在425℃~870℃下进行熔接的方式). Break Point显像点.Break-away Panel可断开板. Breakdown Voltage崩溃电压. Break-out破出.Bridging搭桥.Bright Dip光泽浸渍处理. Brightener光泽剂.Brown Oxide棕氧化.Brush Plating刷镀.B-stageB阶段.Build Up Process增层法制程.Build-up堆积.Bulge鼓起.Bump 突块.Bumping Process凸块制程. Buoyancy浮力.Buried Via Hole埋导孔.Burn-in高温加速老化试验.Burning烧焦.Burr毛头.Bus Bar汇电杆.Butter Coat 外表树脂层.*****C*****C4 Chip JointC4芯片焊接.Cable电缆.CAD计算机辅助设计.Calendered Fabric轧平式纲布.Cap Lamination帽式压合法. Capacitance电容.Capacitive Coupling电容耦合. Capillary Action毛细作用.Carbide碳化物.Carbon Arc Lamp碳弧灯.Carbon Treatment, Active活化炭处理.Card卡板.Card Cages/Card Racks电路板构装箱.Carlson Pin卡氏定位稍.Carrier载体.Cartridge滤心.Castallation堡型绩体电路器.Catalyzed Board, Catalyzed Substrate催化板材. Catalyzing催化.Cathode阴极.Cation阴向离子, 阳离子.Caul Plate隔板.Cavitation空泡化半真空.Center-to-Center Spacing中心间距.Ceramics陶瓷.Cermet陶金粉.Certificate证明书.CFC氟氢碳化物.Chamfer倒角.Characteristic Impedance特性阻抗.Chase纲框.Check List检查清单.Chelate螯合.Chemical Milling化学研磨.Chemical Resistance抗化性.Chemisorption化学吸附.Chip芯片(粒).Chip Interconnection芯片互连.Chip on Board芯片粘着板.Chip On Glass晶玻接装(COG).Chisel钻针的尖部.Chlorinated Solvent含氯溶剂,氯化溶剂. Circumferential Separation环状断孔.Clad/Cladding披覆.Clean Room无尘室.Cleanliness清洁度.Clearance余地,余环.Clinched Lead Terminal紧箝式引脚.Clinched-wire Through Connection通孔弯线连接法 . Clip Terminal绕线端接.Coat, Coating皮膜表层.Coaxial Cable同轴缆线.Coefficient of Thermal Expansion热膨胀系数.Co-Firing共绕.Cold Flow冷流.Cold Solder Joint冷焊点.Collimated Light平行光.Colloid胶体.Columnar Structure柱状组织.Comb Pattern梳型电路.Complex Ion错离子.Component Hole零件孔.Component Orientation零件方向. Component Side组件面.Composites,(CEM-1,CEM-3)复合板材. Condensation Soldering凝热焊接,液化放热焊接. Conditioning整孔.Conductance导电.Conductive Salt导电盐.Conductivity导电度.Conductor Spacing导体间距.Conformal Coating贴护层.Conformity吻合性, 服贴性.Connector连接器.Contact Angle接触角.Contact Area接触区.Contact Resistance接触电阻.Continuity连通性.Contract Service协力厂,分包厂.Controlled Depth Drilling定深钻孔. Conversion Coating 转化皮膜.Coplanarity共面性.Copolymer共聚物.Copper Foil铜皮.Copper Mirror Test铜镜试验.Copper Paste铜膏.Copper-Invar-Copper (CIC)综合夹心板.Core Material内层板材,核材.Corner Crack 通孔断角.Corner Mark板角标记.Counterboring方型扩孔.Countersinking锥型扩孔.Coupling Agent 偶合剂.Coupon, Test Coupon板边试样.Coverlay/Covercoat表护层.Crack裂痕.Crazing白斑.Crease皱折.Creep潜变.Crossection Area截面积.Crosshatch Testing十字割痕试验. Crosshatching十字交叉区.Crosslinking, Crosslinkage交联,架桥. Crossover越交,搭交.Crosstalk噪声, 串讯.Crystalline Melting Point晶体熔点.C-Stage C阶段.Cure硬化,熟化.Current Density电流密度.Current-Carrying Capability载流能力.Curtain Coating濂涂法.*****D*****Daisy Chained Design菊瓣设计.Datum Reference基准参考.Daughter Board子板.Debris碎屑,残材.Deburring去毛头.Declination Angle斜射角.Definition边缘逼真度.Degradation 劣化.Degrasing脱脂.Deionized Water去离子水.Delamination分离.Dendritic Growth 枝状生长.Denier丹尼尔(是编织纺织所用各种纱类直径单位, 定义9000米纱束所具有的重量(以克米计)). Densitomer透光度计.Dent凹陷.Deposition 皮膜处理.Desiccator干燥器.Desmearing去胶渣.Desoldering解焊.Developer显像液,显像机.Developing显像 .Deviation偏差.Device电子组件.Dewetting缩锡.D-glassD玻璃.Diaze Film偶氮棕片.Dichromate重铬酸盐.Dicing芯片分割.Dicyandiamide(Dicy)双氰胺.Die 冲模.Die Attach晶粒安装.Die Bonding晶粒接着.Die Stamping冲压.Dielectric 介质.Dielectric Breakdown Voltage介质崩溃电压.Dielectric Constant介质常数.Dielectric Strength介质强度.Differential Scanning Calorimetry(DSC)微差扫瞄热卡分析法. Diffusion Layer扩散层.Digitizing数字化.Dihedral Angle双反斜角.Dimensional Stability尺度安定性.Diode二极管.Dip Coating浸涂法.Dip Soldering浸焊法.DIP(Dual Inline Package)双排脚封装体.Dipole偶极,双极.Direct / Indirect Stencil直接/间接版膜.Direct Emulsion直接乳胶.Direct Plating直接电镀.Discrete Compenent散装零件.Discrete Wiring Board散线电路板,复线板.Dish Down碟型下陷.Dispersant分散剂.Dissipation Factor散失因素.Disspation Factor散逸因子.Disturbed Joint受扰焊点.Doctor Blade修平刀,刮平刀.Dog Ear狗耳.Doping掺杂.Double Layer双电层.Double Treated Foil双面处理铜箔.Drag In / Drag Out带[进/带出.Drag Soldering拖焊.Drawbridging吊桥效应.Drift漂移.Drill Facet钻尖切削面.Drill Pointer钻针重磨机.Drilled Blank已钻孔的裸板.Dross浮渣.Drum Side铜箔光面.Dry Film干膜.Dual Wave Soldering 双波焊接.Ductility展性.Dummy Land假焊垫.Dummy, Dummying假镀(片).Durometer橡胶硬度计.DYCOstrate电浆蚀孔增层法.Dynamic Flex(FPC)动态软板.*****E*****E-Beam (Electron Beam)电子束.Eddy Current涡电流.Edge Spacing板边空地.Edge-Board Connector板边(金手指)承接器. Edge-Board Contact板边金手指.Edge-Dip Solderability Test板边焊锡性测试. EDTA乙二胺四乙酸.Effluent排放物.E-glass电子级玻璃.Elastomer弹性体.Electric Strength(耐)电性强度. Electrodeposition电镀.Electro-deposition Photoresist电着光阻, 电泳光阻. Electroforming电铸.Electroless-Deposition无电镀.Electrolytic Tough Pitch电解铜..Electrolytic-Cleaning电解清洗.Electro-migration电迁移.Electro-phoresis电泳动, 电渗.Electro-tinning镀锡.Electro-Winning电解冶炼.Elongation 延伸性, 延伸率.Embossing凸出性压花.EMF(Electromotive Force)电动势.EMI(Electromagnetic Interference)电磁干扰. Emulsion乳化.Emulsion Side药膜面.Encapsulating胶囊.Encroachment沾污,侵犯.End Tap封头.Entek有机护铜处理.Entrapment夹杂物.Entry Material盖板.Epoxy Resin环氧树脂.Etch Factor蚀刻因子.Etchant蚀刻剂(液).Etchback回蚀.Etching Indicator蚀刻指针.Etching Resist蚀刻阻剂.Eutetic Composition共融组成.Exotherm放热(曲线).Exposure曝光.Eyelet铆眼.*****F*****Fabric纲布.Face Bonding反面朝下结合.Failure故障.Fan Out Wiring/Fan In Wiring扇出布线/扇入布线. Farad 法拉.Farady法拉第.Fatigue Strength抗疲劳强度.Fault缺陷.Fault Plane断层面.Feed Through Hole导通孔.Feeder 进料器.Fiber Exposure玻纤显露.Fiducial Mark基准记号.Filament纤丝.Fill纬向.Filler填充料.Fillet内圆填角.Film底片.Film Adhesive接着膜,粘合膜.Filter过滤器.Fine Line细线.Fine Pitch密脚距,密线距,密垫距.Fineness粒度, 纯度.Finger手指.Finishing终修(饰).Finite Element Method有限要素分析法.First Article首产品.First Pass-Yield初检良品率.Fixture夹具.Flair刃角变形.Flame Point自燃点.Flame Resistant耐燃性.Flammability Rate燃性等级.Flare扇形崩口.Flash Plating闪镀.Flashover闪络.Flat Cable扁平排线.Flat Pack扁平封装(之零件).Flatness平坦度.Flexible Printed Circuit (FPC)软板.Flexural Failure挠曲损坏.Flexural Module弯曲模数, 抗挠性模数 . Flexural Strength抗挠强度.Flip Chip覆晶,扣晶.Flocculation絮凝.Flood Stroke Print覆墨冲程印刷.Flow Soldering (Wave Soldering)流焊. Fluorescence荧光.Flurocarbon Resin碳氟树脂.Flush Conductor嵌入式线路, 贴平式导体. Flush Point闪火点.Flute退屑槽.Flux助焊剂.Foil Burr铜箔毛边.Foil Lamination铜箔压板法.Foot残足(干膜残余物).Foot Print (Land Pattern)脚垫.Foreign Material 外来物,异物.Form-to-List布线说明清单.Four Point Twisting四点扭曲法.Free Radical自由基.Freeboard干舷.Frequency频率.Frit 玻璃熔料.Fully-Additive Process全加成法.Fungus Resistance抗霉性.Fused Coating熔锡层.Fusing熔合.Fusing Fluid助熔液.*****G*****G-10由连续玻纤所织成的玻纤布与环氧树脂粘结剂所复合成的材料.Gage, Gauge量规.Gallium Arsenide (GaAs)砷化镓.Galvanic Corrosion贾凡尼式腐蚀(电解式腐蚀). Galvanic Series贾凡尼次序(电动次序). Galvanizing镀锌.GAP第一面分离,长刃断开.Gate Array闸列,闸极数组.Gel Time胶化时间.Gelation Particle胶凝点.Gerber Data ,Gerber File格博档案(是美商Gerber公司专为PCB面线路图形与孔位,所发展一系列完整的软件档案).Ghost Image阴影.Gilding镀金(现为:Glod Plating).Glass Fiber玻纤.Glass Fiber Protrusion/Gouging, Groove玻纤突出/挖破.Glass Transition Temperature, Tg玻璃态转化温度.Glaze釉面,釉料.Glob Top圆顶封装体.Glouble Test球状测试法.Glycol (Ethylene Glycol)乙二醇.Golden Board测试用标准板.Grain Size结晶粒度.Grass Leak 大漏.Grid标准格.Ground Plane /Earth Plane接地层.Ground Plane Clearance接地空环.Guide Pin导针.Gull /Wing Lead鸥翼引脚.*****H*****Halation环晕.Half Angle半角.Halide卤化物.Haloing白圈,白边.Halon海龙,是CFC"氟碳化物"的一种商品名.Hard Anodizing硬阳极化.Hard Chrome Plating镀硬铬.Hard Soldering硬焊.Hardener (Curing Agent)硬化剂(或Curing Agent).Hardness硬度.Haring-Blum Cell海固槽.Harness电缆组合.Hay Wire跳线.Heat Cleaning烧洁.Heat Dissipation散热.Heat Distortion Point (Temp)热变形点(温度).Heat Sealing热封.Heat Sink Plane散热层.Heat Transfer Paste导热膏.Heatsink Tool散热工具.Hertz(Hz)赫.High Efficiency Particulate Air Filter (HEPA)高效空气尘粒过泸机. Hipot Test 高压电测.Hi-Rel高度靠度.Hit 击(钻孔时钻针每一次"刺下"的动作). Holding Time停置时间.Hole Breakout孔位破出.Hole Counter数孔机.Hole Density孔数密度.Hole Preparation通孔准备.Hole Pull Strength孔壁强度.Hole Void破洞.Hook 切削刀缘外凸.Hot Air Levelling喷锡.Hot Bar Soldering热把焊接.Hot Gas Soldering热风手焊.HTE(High Temperature Elongation)高温延伸性. Hull Cell哈氏槽.Hybrid Integrated Circuit混成电路. Hydraulic Bulge Test液压鼓起试验. Hydrogen Embrittlement氢脆.Hydrogen Overvoltage氢过(超)电压. Hydrolysis水解.Hydrophilic亲水性.Hygroscopic吸湿性.Hypersorption超吸咐.*****I*****I.C. Socket绩体电路器插座.Icicle锡尖.Illuminance照度.Image Transfer影像转移.Immersion Plating浸镀.Impedance阻抗.Impedance Match阻抗匹配.Impregnate含浸.In-Circuit Testing组装板电测.Inclusion异物,夹杂物.Indexing Hole基准孔.Inductance(L)电感.Infrared(IR)红外线.Input/Output输入/输出.Insert, Insertion插接.Inspection Overlay套检底片.Insulation Resistance绝缘电阻.Integrated Circuit(IC)绩体电路器.Inter Face接口.Interconnection互连.Intermetallic Compound (IMC)接口共化物.Internal Stress内应力.Interposer互边导电物.Interstitial Via-Hole(IVH)局部层间导通孔.Invar殷钢(63.8%Fe,36%Ni,0.2%C).Ion Cleanliness离子清洁度.Ion Exchange Resins离子交换树脂.Ion Migration离子迁移.Ionizable (Ionic) Contaimination离子性污染.Ionization游离,电离.Ionization Voltage (Corona Level)电离化电压(电缆内部狭缝空气中,引起其电离所施加之最小电压).IPC美国印刷电路板协会.Isolation隔离性,隔绝性.*****J*****JEDEC(Joint Electronic Device 联合电子组件工程委员会. Engineering Council)J-LeadJ型接脚.Job Shop专业工厂.Joule焦耳.Jumper Wire跳线.Junction接(合)面,接头.Just-In-Time(JIT)适时供应,及时出现.*****K*****Kapton聚亚醯胺软板.Karat克拉(1克拉(钻石)=0.2g 纯金则24k金为100%的钝金.Kauri-Butanol Value考立丁醇值(简称K.B.值).Kerf.切形,裁剪.Kevlar聚醯胺纤维.Key电键Key Board键盘.Kiss Pressure吻压, 低压.Knoop Hardness努普硬度.Known Good Die(KGD)已知之良好芯片.Kovar科伐合金(Fe53%,Ni29%,Co17%).Kraft Paper牛皮纸.*****L*****Lamda Wave延伸平波.Laminar Flow平流.Laminar Structure片状结构.Laminate Void板材空洞.Laminate(s)基板.Lamination Void压合空洞.Laminator压膜机.Land孔环焊垫,表面焊垫.Landless Hole无环通孔.Laser Direct Imaging (LDI)雷射直接成像.Laser Maching雷射加工法.Laser Photogenerator(LPG), Laser Photoplotter雷射曝光机. Laser Soldering雷射焊接法.Lay Back 刃角磨损.Lay Out布线,布局.Lay Up 叠合.Layer to Layer Spacing层间距离Leaching焊散漂出,熔出.Lead 引脚.Lead Frame脚架.Lead Pitch脚距.Leakage Current漏电电流.Legend文字标记.Leveling整平.Lifted Land孔环(焊垫)浮起.Ligand错离子附属体.Light Emitting Diodes (LED)发光二极管.Light Integrator光能累积器.Light Intensity光强度.Limiting Current Density极限电流密度.Liquid Crystal Display (LCD)液晶显示器.Liquid Dielectrics液态介质.Liquid Photoimagible Solder Mask, (LPSM)液态感光防焊绿漆. Local Area Network区域性网络.Logic 逻辑.Logic Circuit 逻辑电路.Loss Factor损失因素.Loss Tangent (TanδDK)损失正切.Lot Size批量.Luminance发光强度.Lyophilic亲水性胶体.*****M*****Macro-Throwing Power巨观分布力.Major Defect主要(严重)缺点.Major Weave Direction主要织向.Margin刃带(钻头尖部).Marking标记.Mask阻剂.Mass Finishing大量整面(拋光).Mass Lamination大型压板.Mass Transport质量输送.Master Drawing主图.Mat席(用于CEM-3(Composite Epoxy Material)的复合材料.)Matte Side毛面(电镀铜皮(ED Foil)之粗糙面).Mealing泡点.Mean Time To Failure (MTTF)故障前可用之平均时数. Measling白点.Mechanical Stretcher机械式张网机.Mechanical Warp机械式缠绕.Mechanism机理.Membrane Switch薄膜开关.Meniscograph Test弧面状沾锡试验.Meniscus弯月面.Mercury Vaper Lamp汞气灯.Mesh Count纲目数.Metal Halide Lamp 金属卤素灯.Metallization金属化.Metallized Fabric金属化纲布.Micelle微胞.Micro Wire Board微封线板.Micro-electronios微电子.Microetching微蚀.Microsectioning微切片法.Microstrip 微条.Microstrip Line微条线,微带线.Microthrowing Power微分布力.Microwave微波.Migration迁移.Migration Rate迁移率.Mil英丝.Minimum Annular Ring孔环下限.Minimum Electrical Spacing电性间距下限.Minor Weave Direction次要织向.Misregistration 对不准度.Mixed Componmt Mounting Technology混合零件之组装技术. Modem调变及解调器.Modification修改.Module模块.Modulus of Elasticity弹性系数.Moisture and Insulation Resistance Test湿气与绝缘电阻试验. Mold Release 脱模剂,离型剂.Mole摩尔.Monofilament单丝.Mother Board主机板,母板.Moulded Circuit模造立体电路机.Mounting Hole安装孔.Mounting Hole组装孔,机装孔.Mouse Bite鼠齿(蚀刻后线路边缘出现不规则缺口). Multi-Chip-Module(MCM)多芯片芯片模块. Multiwiring Board (or Discrete Wiring Board)复线板.*****N*****N.C.数值控制.Nail Head钉头.Near IR近红外线.Negative负片,钻尖的第一面外缘变窄.Negative Etch-back反回蚀.Negative Stencil负性感光膜.Negative-Acting Resist负性作用之阻剂.Network纲状元件.Newton牛顿.Newton Ring 牛顿环.Newtonian Liquid牛顿流体.Nick缺口.N-Methyl Pyrrolidine (NMP)N-甲基四氢哔咯.Noble Metal Paste贵金属印膏.Node节点.Nodule节瘤.Nomencleature标示文字符号.Nominal Cured Thickness标示厚度.Non-Circular Land非圆形孔环焊垫.Non-flammable非燃性.Non-wetting不沾锡.Normal Concentration (Strength)标准浓度,当量浓度. Normal Distribution常态分布.Novolac酯醛树脂.Nucleation , Nucleating核化.Numerical Control数值控制.Nylon尼龙.*****O*****Occlusion吸藏.Off-Contact架空.Offset第一面大小不均.OFHC(Oxyen Free High Conductivity)无氧高导电铜. Ohm欧姆.Oilcanning盖板弹动.OLB(Outer Lead Bond)外引脚结合.Oligomer寡聚物.Omega Meter离子污染检测仪.Omega Wave振荡波.On-Contact Printing密贴式印刷.Opaquer不透明剂,遮光剂.Open Circuits断线.Optical Comparater光学对比器(光学放大器.) Optical Density光密度.Optical Inspection光学检验.Optical Instrument光学仪器.Organic Solderability Preservatives (OSP)有机保焊剂. Osmosis渗透.Outgassing出气,吹气.Outgrowth悬出,横出,侧出.Output产出,输出.Overflow溢流.Overhang总悬空.Overlap 钻尖点分离.Overpotantial(Over voltage)过电位,过电压. Oxidation氧化.Oxygen Inhibitor氧化抑制剂.Ozone Depletion臭氧层耗损.*****P*****Packaging封装,构装.Pad焊垫,圆垫.Pad Master圆垫底片.Pads Only Board唯垫板.Palladium钯.Panel制程板.Panel Plating全板镀铜.Panel Process全板电镀法.Paper Phenolic纸质酚醛树脂(板材).Parting Agent脱膜剂.Passivation钝化,钝化外理.Passive Device (Component)被动组件(零件)Paste膏,糊.Pattern板面图形.Pattern Plating线路电镀.Pattern Process线路电镀法.Peak Voltage峰值电压.Peel Strength抗撕强度.Periodic Reverse (PR) Current周期性反电流. Peripheral周边附属设备.Permeability透气性,导磁率.Permittivity诱电率,透电率.。
PCB专业词汇
PCB专业词汇⼀、综合词汇1、印制电路：printed circuit2、印制线路：printed wiring3、印制板：printed board4、印制板电路：printed circuit board (pcb)5、印制线路板：printed wiring board(pwb)6、印制元件：printed component7、印制接点：printed contact8、印制板装配：printed board assembly9、板：board10、单⾯印制板：single-sided printed board(ssb)11、双⾯印制板：double-sided printed board(dsb)12、多层印制板：mulitlayer printed board(mlb)13、多层印制电路板：mulitlayer printed circuit board14、多层印制线路板：mulitlayer prited wiring board15、刚性印制板：rigid printed board16、刚性单⾯印制板：rigid single-sided printed borad17、刚性双⾯印制板：rigid double-sided printed borad18、刚性多层印制板：rigid multilayer printed board19、挠性多层印制板：flexible multilayer printed board20、挠性印制板：flexible printed board21、挠性单⾯印制板：flexible single-sided printed board22、挠性双⾯印制板：flexible double-sided printed board23、挠性印制电路：flexible printed circuit (fpc)24、挠性印制线路：flexible printed wiring25、刚性印制板：flex-rigid printed board, rigid-flex printed board26、刚性双⾯印制板：flex-rigid double-sided printed board, rigid-flex double-sided printed27、刚性多层印制板：flex-rigid multilayer printed board, rigid-flex multilayer printed board28、齐平印制板：flush printed board29、⾦属芯印制板：metal core printed board30、⾦属基印制板：metal base printed board31、多重布线印制板：mulit-wiring printed board32、陶瓷印制板：ceramic substrate printed board33、导电胶印制板：electroconductive paste printed board34、模塑电路板：molded circuit board35、模压印制板：stamped printed wiring board36、顺序层压多层印制板：sequentially-laminated mulitlayer37、散线印制板：discrete wiring board38、微线印制板：micro wire board39、积层印制板：buile-up printed board40、积层多层印制板：build-up mulitlayer printed board (bum)41、积层挠印制板：build-up flexible printed board42、表⾯层合电路板：surface laminar circuit (slc)43、埋⼊凸块连印制板：b2it printed board44、多层膜基板：multi-layered film substrate(mfs)45、层间全内导通多层印制板：alivh multilayer printed board46、载芯⽚板：chip on board (cob)47、埋电阻板：buried resistance board48、母板：mother board49、⼦板：daughter board50、背板：backplane51、裸板：bare board52、键盘板夹⼼板：copper-invar-copper board53、动态挠性板：dynamic flex board54、静态挠性板：static flex board55、可断拼板：break-away planel56、电缆：cable57、挠性扁平电缆：flexible flat cable (ffc)58、薄膜开关：membrane switch59、混合电路：hybrid circuit60、厚膜：thick film61、厚膜电路：thick film circuit62、薄膜：thin film63、薄膜混合电路：thin film hybrid circuit64、互连：interconnection65、导线：conductor trace line66、齐平导线：flush conductor67、传输线：transmission line68、跨交：crossover69、板边插头：edge-board contact70、增强板：stiffener71、基底：substrate72、基板⾯：real estate73、导线⾯：conductor side74、元件⾯：component side75、焊接⾯：solder side76、印制：printing77、⽹格：grid78、图形：pattern79、导电图形：conductive pattern80、⾮导电图形：non-conductive pattern81、字符：legend82、标志：mark⼆、基材：1、基材：base material2、层压板：laminate3、覆⾦属箔基材：metal-clad bade material4、覆铜箔层压板：copper-clad laminate (ccl)5、单⾯覆铜箔层压板：single-sided copper-clad laminate6、双⾯覆铜箔层压板：double-sided copper-clad laminate7、复合层压板：composite laminate8、薄层压板：thin laminate9、⾦属芯覆铜箔层压板：metal core copper-clad laminate10、⾦属基覆铜层压板：metal base copper-clad laminate11、挠性覆铜箔绝缘薄膜：flexible copper-clad dielectric film12、基体材料：basis material13、预浸材料：prepreg14、粘结⽚：bonding sheet15、预浸粘结⽚：preimpregnated bonding sheer16、环氧玻璃基板：epoxy glass substrate17、加成法⽤层压板：laminate for additive process18、预制内层覆箔板：mass lamination panel19、内层芯板：core material20、催化板材：catalyzed board ,coated catalyzed laminate21、涂胶催化层压板：adhesive-coated catalyzed laminate22、涂胶⽆催层压板：adhesive-coated uncatalyzed laminate23、粘结层：bonding layer24、粘结膜：film adhesive25、涂胶粘剂绝缘薄膜：adhesive coated dielectric film26、⽆⽀撑胶粘剂膜：unsupported adhesive film27、覆盖层：cover layer (cover lay)28、增强板材：stiffener material29、铜箔⾯：copper-clad surface30、去铜箔⾯：foil removal surface31、层压板⾯：unclad laminate surface32、基膜⾯：base film surface33、胶粘剂⾯：adhesive faec34、原始光洁⾯：plate finish35、粗⾯：matt finish36、纵向：length wise direction37、模向：cross wise direction38、剪切板：cut to size panel39、酚醛纸质覆铜箔板：phenolic cellulose paper copper-clad laminates(phenolic/paper ccl)40、环氧纸质覆铜箔板：epoxide cellulose paper copper-clad laminates (epoxy/paper ccl)41、环氧玻璃布基覆铜箔板：epoxide woven glass fabric copper-clad laminates42、环氧玻璃布纸复合覆铜箔板：epoxide cellulose paper core, glass cloth surfaces copper-clad laminates43、环氧玻璃布玻璃纤维复合覆铜箔板：epoxide non woven/woven glass reinforced copper-clad laminates44、聚酯玻璃布覆铜箔板：ployester woven glass fabric copper-clad laminates45、聚酰亚胺玻璃布覆铜箔板：polyimide woven glass fabric copper-clad laminates46、双马来酰亚胺三嗪环氧玻璃布覆铜箔板：bismaleimide/triazine/epoxide woven glass fabric copper-clad lamimates47、环氧合成纤维布覆铜箔板：epoxide synthetic fiber fabric copper-clad laminates48、聚四⼄烯玻璃纤维覆铜箔板：teflon/fiber glass copper-clad laminates49、超薄型层压板：ultra thin laminate50、陶瓷基覆铜箔板：ceramics base copper-clad laminates51、紫外线阻挡型覆铜箔板：uv blocking copper-clad laminates三、基材的材料1、 a阶树脂：a-stage resin2、 b阶树脂：b-stage resin3、 c阶树脂：c-stage resin4、环氧树脂：epoxy resin5、酚醛树脂：phenolic resin6、聚酯树脂：polyester resin7、聚酰亚胺树脂：polyimide resin8、双马来酰亚胺三嗪树脂：bismaleimide-triazine resin9、丙烯酸树脂：acrylic resin10、三聚氰胺甲醛树脂：melamine formaldehyde resin11、多官能环氧树脂：polyfunctional epoxy resin12、溴化环氧树脂：brominated epoxy resin13、环氧酚醛：epoxy novolac14、氟树脂：fluroresin15、硅树脂：silicone resin16、硅烷：silane17、聚合物：polymer18、⽆定形聚合物：amorphous polymer19、结晶现象：crystalline polamer20、双晶现象：dimorphism21、共聚物：copolymer22、合成树脂：synthetic23、热固性树脂：thermosetting resin24、热塑性树脂：thermoplastic resin25、感光性树脂：photosensitive resin26、环氧当量：weight per epoxy equivalent (wpe)27、环氧值：epoxy value28、双氰胺：dicyandiamide29、粘结剂：binder30、胶粘剂：adesive31、固化剂：curing agent32、阻燃剂：flame retardant33、遮光剂：opaquer34、增塑剂：plasticizers35、不饱和聚酯：unsatuiated polyester36、聚酯薄膜：polyester37、聚酰亚胺薄膜：polyimide film (pi)38、聚四氟⼄烯：polytetrafluoetylene (ptfe)39、聚全氟⼄烯丙烯薄膜：perfluorinated ethylene-propylene copolymer film (fep)40、增强材料：reinforcing material41、玻璃纤维：glass fiber42、 e玻璃纤维：e-glass fibre43、 d玻璃纤维：d-glass fibre44、 s玻璃纤维：s-glass fibre45、玻璃布：glass fabric46、⾮织布：non-woven fabric47、玻璃纤维垫：glass mats48、纱线：yarn 49、单丝：filament50、绞股：strand51、纬纱：weft yarn52、经纱：warp yarn53、但尼尔：denier54、经向：warp-wise55、纬向：weft-wise, filling-wise56、织物经纬密度：thread count57、织物组织：weave structure58、平纹组织：plain structure59、坏布：grey fabric60、稀松织物：woven scrim61、⼸纬：bow of weave62、断经：end missing63、缺纬：mis-picks64、纬斜：bias65、折痕：crease66、云织：waviness67、鱼眼：fish eye68、⽑圈长：feather length69、厚薄段：mark70、裂缝：split71、捻度：twist of yarn72、浸润剂含量：size content73、浸润剂残留量：size residue74、处理剂含量：finish level75、浸润剂：size76、偶联剂：couplint agent77、处理织物：finished fabric78、聚酰胺纤维：polyarmide fiber79、聚酯纤维⾮织布：non-woven polyester fabric80、浸渍绝缘纵纸：impregnating insulation paper81、聚芳酰胺纤维纸：aromatic polyamide paper82、断裂长：breaking length83、吸⽔⾼度：height of capillary rise84、湿强度保留率：wet strength retention85、⽩度：whitenness86、陶瓷：ceramics87、导电箔：conductive foil88、铜箔：copper foil89、电解铜箔：electrodeposited copper foil (ed copper foil)90、压延铜箔：rolled copper foil91、退⽕铜箔：annealed copper foil92、压延退⽕铜箔：rolled annealed copper foil (ra copper foil)93、薄铜箔：thin copper foil94、涂胶铜箔：adhesive coated foil95、涂胶脂铜箔：resin coated copper foil (rcc)96、复合⾦属箔：composite metallic material97、载体箔：carrier foil98、殷⽡：invar99、箔（剖⾯）轮廓：foil profile100、光⾯：shiny side101、粗糙⾯：matte side102、处理⾯：treated side103、防锈处理：stain proofing104、双⾯处理铜箔：double treated foil四、设计1、原理图：shematic diagram2、逻辑图：logic diagram3、印制线路布设：printed wire layout4、布设总图：master drawing5、可制造性设计：design-for-manufacturability6、计算机辅助设计：computer-aided design.(cad)7、计算机辅助制造：computer-aided manufacturing.(cam)8、计算机集成制造：computer integrat manufacturing.(cim)9、计算机辅助⼯程：computer-aided engineering.(cae)10、计算机辅助测试：computer-aided test.(cat)11、电⼦设计⾃动化：electric design automation .(eda)12、⼯程设计⾃动化：engineering design automaton .(eda2)13、组装设计⾃动化：assembly aided architectural design. (aaad)14、计算机辅助制图：computer aided drawing15、计算机控制显⽰：computer controlled display .(ccd)16、布局：placement17、布线：routing18、布图设计：layout19、重布：rerouting20、模拟：simulation21、逻辑模拟：logic simulation22、电路模拟：circit simulation23、时序模拟：timing simulation24、模块化：modularization25、布线完成率：layout effeciency26、机器描述格式：machine descripttionm format .(mdf)27、机器描述格式数据库：mdf databse28、设计数据库：design database29、设计原点：design origin30、优化（设计）：optimization (design)31、供设计优化坐标轴：predominant axis32、表格原点：table origin33、镜像：mirroring34、驱动⽂件：drive file35、中间⽂件：intermediate file36、制造⽂件：manufacturing documentation37、队列⽀撑数据库：queue support database38、元件安置：component positioning39、图形显⽰：graphics dispaly40、⽐例因⼦：scaling factor41、扫描填充：scan filling42、矩形填充：rectangle filling43、填充域：region filling44、实体设计：physical design45、逻辑设计：logic design46、逻辑电路：logic circuit47、层次设计：hierarchical design48、⾃顶向下设计：top-down design49、⾃底向上设计：bottom-up design50、线⽹：net51、数字化：digitzing52、设计规则检查：design rule checking53、⾛（布）线器：router (cad)54、⽹络表：net list55、计算机辅助电路分析：computer-aided circuit analysis56、⼦线⽹：subnet57、⽬标函数：objective function58、设计后处理：post design processing (pdp)59、交互式制图设计：interactive drawing design60、费⽤矩阵：cost metrix61、⼯程图：engineering drawing62、⽅块框图：block diagram63、迷宫：moze64、元件密度：component density65、巡回售货员问题：traveling salesman problem66、⾃由度：degrees freedom67、⼊度：out going degree68、出度：incoming degree69、曼哈顿距离：manhatton distance70、欧⼏⾥德距离：euclidean distance71、⽹络：network72、阵列：array73、段：segment74、逻辑：logic75、逻辑设计⾃动化：logic design automation76、分线：separated time77、分层：separated layer78、定顺序：definite sequence五、形状与尺⼨：1、导线（通道）：conduction (track)2、导线（体）宽度：conductor width3、导线距离：conductor spacing4、导线层：conductor layer5、导线宽度/间距：conductor line/space6、第⼀导线层：conductor layer no.17、圆形盘：round pad8、⽅形盘：square pad9、菱形盘：diamond pad10、长⽅形焊盘：oblong pad11、⼦弹形盘：bullet pad12、泪滴盘：teardrop pad13、雪⼈盘：snowman pad14、 v形盘：v-shaped pad15、环形盘：annular pad16、⾮圆形盘：non-circular pad17、隔离盘：isolation pad18、⾮功能连接盘：monfunctional pad19、偏置连接盘：offset land20、腹（背）裸盘：back-bard land21、盘址：anchoring spaur22、连接盘图形：land pattern23、连接盘⽹格阵列：land grid array24、孔环：annular ring25、元件孔：component hole26、安装孔：mounting hole27、⽀撑孔：supported hole28、⾮⽀撑孔：unsupported hole29、导通孔：via30、镀通孔：plated through hole (pth)31、余隙孔：access hole32、盲孔：blind via (hole)33、埋孔：buried via hole34、埋/盲孔：buried /blind via35、任意层内部导通孔：any layer inner via hole (alivh)36、全部钻孔：all drilled hole37、定位孔：toaling hole38、⽆连接盘孔：landless hole39、中间孔：interstitial hole40、⽆连接盘导通孔：landless via hole41、引导孔：pilot hole42、端接全隙孔：terminal clearomee hole43、准表⾯间镀覆孔：quasi-interfacing plated-through hole44、准尺⼨孔：dimensioned hole45、在连接盘中导通孔：via-in-pad46、孔位：hole location47、孔密度：hole density48、孔图：hole pattern49、钻孔图：drill drawing50、装配图：assembly drawing51、印制板组装图：printed board assembly drawing52、参考基准：datum referance电路板术语总整理*****A*****Abietic Acid松脂酸.Abrasion Resistance耐磨性.Abrasives磨料,刷材.ABS树脂.Absorption吸收(⼊).Ac Impedance交流阻抗.Accelerated Test(Aging)加速⽼化(试验).Acceleration速化反应.Accelerator 加速剂,速化剂.Acceptability,Acceptance 允收性,允收.Access Hole露出孔,穿露孔.Accuracy准确度.Acid Number (Acid Value)酸值.Acoustic Microscope (AM)感⾳成像显微镜.Acrylic压克⼒(聚丙烯酸树脂).Actinic Light (or Intensity, or Radiation)有效光.Activation活化.Activator活化剂.Active Carbon活性炭.Active Parts(Devices)主动零件.Acutance解像锐利度.Addition Agent添加剂.Additive Process加成法.Adhesion附着⼒.Adhesion Promotor附着⼒促进剂.Adhesive胶类或接着剂.Admittance导纳(阻抗的倒数).Aerosol喷雾剂,⽓熔胶,⽓悬体.Aging⽼化.Air Inclusion⽓泡夹杂.Air Knife风⼑.Algorithm算法.Aliphatic Solvent脂肪族溶剂.Aluminium Nitride(AlN)氮化铝.Ambient Tamp环境温度.Amorphous⽆定形,⾮晶形.Amp-Hour安培⼩时.Analog Circuit/Analog Signal模拟电路/模拟讯号. Anchoring Spurs着⼒⽖.Angle of Contack接触⾓.Angle of Attack攻⾓.Anion阴离⼦.Anisotropic异向性,单向的.Anneal 韧化(退⽕).Annular Ring孔环.Anode阳极.Anode Sludge阳极泥.Anodizing阳极化.ANSI美国标准协会.Anti-Foaming Agent消泡剂.Anti-pit Agent抗凹剂.AOI⾃动光学检验.Apertures开⼝,钢版开⼝.AQL品质允收⽔准.AQL(Acceptable Quality Level)允收品质⽔准.Aramid Fiber聚醯胺纤维.Arc Resistance耐电弧性.Array排列.Artwork底⽚.ASIC特定⽤途绩体电路器.Aspect Ratio纵横⽐.Assembly组装装配.A-stage A阶段.ATE⾃动电测设备.Attenuation讯号衰减.Autoclave压⼒锅.Axial-lead轴⼼引脚.Azeotrope共沸混合液.*****B*****Back Light (Back Lighting)背光法.Back Taper反锥斜⾓.Backpanels, Backplanes⽀撑板.Back-up 垫板.Balanced Transmission Lines平衡式传输线.Ball Grid Array球脚数组(封装).Bandability弯曲性.Banking Agent护岸剂.Bare Chip Assembly裸体芯⽚组装.Barrel孔壁,滚镀.Base Material基材.Basic Grid基本⽅格.Batch批.Baume波美度(凡液体⽐重⽐⽔重则 Be=145-(145÷Sp.Gr)凡液体⽐重⽐⽔轻则 Be=140÷(Sp.Gr-130)*Sp.Gr 为⽐重即同体绩物质对"纯⽔"1g/cm的⽐值). Beam lead光芒式的平⾏密集引脚.Bed-of-Nail Testing针床测试.Bellows Conact弹⽚式接触.Beta Ray Backscatter贝他射线反弹散射.Bevelling切斜边.Bias斜张纲布,斜纤法.Bi-Level Stencil]双阶式钢板.Binder粘结剂.Bits头(Drill Bits).Black Oxide⿊氧化层.Blanking冲空断开.Bleack 漂洗.Bleeding溢流.Blind Via Hole肓通孔.Blister局部性分层或起泡.Block Diagram电路系统块图 .Blockout封纲.Blotting⼲印.Blotting Paper吸⽔纸.Blow Hole吹孔.Blue Plaque蓝纹(锡⾯钝化层).Blur Edge (Circle)模糊边带(圈).Bomb Sight弹标.Bond Strength结合强度.Bondability结合性.Bonding Layer结合层接着层.Bonding Sheet(Layer)接合⽚.Bonding Wire结合线.Bow, Bowing板弯.Braid编线.Brazing硬焊(⽤含银的铜锌合⾦焊条).在425℃~870℃下进⾏熔接的⽅式).Break Point显像点.Break-away Panel可断开板.Breakdown Voltage崩溃电压.Break-out破出.Bridging搭桥.Bright Dip光泽浸渍处理.Brightener光泽剂.Brown Oxide棕氧化.Brush Plating刷镀.B-stageB阶段.Build Up Process增层法制程.Build-up堆积.Bulge⿎起.Bump 突块.Bumping Process凸块制程.Buoyancy浮⼒.Buried Via Hole埋导孔.Burn-in⾼温加速⽼化试验.Burning烧焦.Burr⽑头.Bus Bar汇电杆.Butter Coat 外表树脂层.*****C*****C4 Chip JointC4芯⽚焊接.Cable电缆.CAD计算机辅助设计.Calendered Fabric轧平式纲布.Cap Lamination帽式压合法.Capacitance电容.Capacitive Coupling电容耦合.Capillary Action⽑细作⽤.Carbide碳化物.Carbon Arc Lamp碳弧灯.Carbon Treatment, Active活化炭处理.Card卡板.Card Cages/Card Racks电路板构装箱. Carlson Pin卡⽒定位稍.Carrier载体.Cartridge滤⼼.Castallation堡型绩体电路器.Catalyzed Board, Catalyzed Substrate催化板材. Catalyzing催化.Cathode阴极.Cation阴向离⼦, 阳离⼦.Caul Plate隔板.Cavitation空泡化半真空.Center-to-Center Spacing中⼼间距. Ceramics陶瓷.Cermet陶⾦粉.Certificate证明书.CFC氟氢碳化物.Chamfer倒⾓.Characteristic Impedance特性阻抗.Chase纲框.Check List检查清单.Chelate螯合.Chemical Milling化学研磨.Chemical Resistance抗化性.Chemisorption化学吸附.Chip芯⽚(粒).Chip Interconnection芯⽚互连.Chip on Board芯⽚粘着板.Chip On Glass晶玻接装(COG).Chisel钻针的尖部.Chlorinated Solvent含氯溶剂,氯化溶剂. Circumferential Separation环状断孔.Clad/Cladding披覆.Clean Room⽆尘室.Cleanliness清洁度.Clearance余地,余环.Clinched Lead Terminal紧箝式引脚.Clinched-wire Through Connection通孔弯线连接法 . Clip Terminal绕线端接.Coat, Coating⽪膜表层.Coaxial Cable同轴缆线.Coefficient of Thermal Expansion热膨胀系数.Co-Firing共绕.Cold Flow冷流.Cold Solder Joint冷焊点.Collimated Light平⾏光.Colloid胶体.Columnar Structure柱状组织.Comb Pattern梳型电路.Complex Ion错离⼦.Component Hole零件孔.Component Orientation零件⽅向.Component Side组件⾯.Composites,(CEM-1,CEM-3)复合板材. Condensation Soldering凝热焊接,液化放热焊接. Conditioning整孔.Conductance导电.Conductive Salt导电盐.Conductivity导电度.Conductor Spacing导体间距.Conformal Coating贴护层.Conformity吻合性, 服贴性.Connector连接器.Contact Angle接触⾓.Contact Area接触区.Contact Resistance接触电阻.Continuity连通性.Contract Service协⼒⼚,分包⼚.Controlled Depth Drilling定深钻孔.Conversion Coating 转化⽪膜.Coplanarity共⾯性.Copolymer共聚物.Copper Foil铜⽪.Copper Mirror Test铜镜试验.Copper Paste铜膏.Copper-Invar-Copper (CIC)综合夹⼼板.Core Material内层板材,核材.Corner Crack 通孔断⾓.Corner Mark板⾓标记.Counterboring⽅型扩孔.Countersinking锥型扩孔.Coupling Agent 偶合剂.Coupon, Test Coupon板边试样.Coverlay/Covercoat表护层.Crack裂痕.Crazing⽩斑.Crease皱折.Creep潜变.Crossection Area截⾯积.Crosshatch Testing⼗字割痕试验. Crosshatching⼗字交叉区.Crosslinking, Crosslinkage交联,架桥. Crossover越交,搭交.Crosstalk噪声, 串讯.Crystalline Melting Point晶体熔点.C-Stage C阶段.Cure硬化,熟化.Current Density电流密度.Current-Carrying Capability载流能⼒.Curtain Coating濂涂法.*****D*****Daisy Chained Design菊瓣设计.Datum Reference基准参考.Daughter Board⼦板.Debris碎屑,残材.Deburring去⽑头.Declination Angle斜射⾓.Definition边缘逼真度.Degradation 劣化.Degrasing脱脂.Deionized Water去离⼦⽔.Delamination分离.Dendritic Growth 枝状⽣长.Denier丹尼尔(是编织纺织所⽤各种纱类直径单位,定义9000⽶纱束所具有的重量(以克⽶计)). Densitomer透光度计.Dent凹陷.Deposition ⽪膜处理.Desiccator⼲燥器.Desmearing去胶渣.Desoldering解焊.Developer显像液,显像机.Developing显像 .Deviation偏差.Device电⼦组件.Dewetting缩锡.D-glassD玻璃.Diaze Film偶氮棕⽚.Dichromate重铬酸盐.Dicing芯⽚分割.Dicyandiamide(Dicy)双氰胺.Die 冲模.Die Attach晶粒安装.Die Bonding晶粒接着.Die Stamping冲压.Dielectric 介质.Dielectric Breakdown Voltage介质崩溃电压.Dielectric Constant介质常数.Dielectric Strength介质强度.Differential Scanning Calorimetry(DSC)微差扫瞄热卡分析法. Diffusion Layer扩散层.Digitizing数字化.Dihedral Angle双反斜⾓.Dimensional Stability尺度安定性.Diode⼆极管.Dip Coating浸涂法.Dip Soldering浸焊法.DIP(Dual Inline Package)双排脚封装体.Dipole偶极,双极.Direct / Indirect Stencil直接/间接版膜.Direct Emulsion直接乳胶.Direct Plating直接电镀.Discrete Compenent散装零件.Discrete Wiring Board散线电路板,复线板.Dish Down碟型下陷.Dispersant分散剂.Dissipation Factor散失因素.Disspation Factor散逸因⼦.Disturbed Joint受扰焊点.Doctor Blade修平⼑,刮平⼑.Dog Ear狗⽿.Doping掺杂.Double Layer双电层.Double Treated Foil双⾯处理铜箔.Drag In / Drag Out带[进/带出.Drag Soldering拖焊.Drawbridging吊桥效应.Drift漂移.Drill Facet钻尖切削⾯.Drill Pointer钻针重磨机.Drilled Blank已钻孔的裸板.Dross浮渣.Drum Side铜箔光⾯.Dry Film⼲膜.Dual Wave Soldering 双波焊接.Ductility展性.Dummy Land假焊垫.Dummy, Dummying假镀(⽚).Durometer橡胶硬度计.DYCOstrate电浆蚀孔增层法.Dynamic Flex(FPC)动态软板.*****E*****E-Beam (Electron Beam)电⼦束.Eddy Current涡电流.Edge Spacing板边空地.Edge-Board Connector板边(⾦⼿指)承接器.Edge-Board Contact板边⾦⼿指.Edge-Dip Solderability Test板边焊锡性测试.EDTA⼄⼆胺四⼄酸.Effluent排放物.E-glass电⼦级玻璃.Elastomer弹性体.Electric Strength(耐)电性强度.Electrodeposition电镀.Electro-deposition Photoresist电着光阻, 电泳光阻. Electroforming电铸.Electroless-Deposition⽆电镀.Electrolytic Tough Pitch电解铜..Electrolytic-Cleaning电解清洗.Electro-migration电迁移.Electro-phoresis电泳动, 电渗.Electro-tinning镀锡.Electro-Winning电解冶炼.Elongation 延伸性, 延伸率.Embossing凸出性压花.EMF(Electromotive Force)电动势.EMI(Electromagnetic Interference)电磁⼲扰. Emulsion乳化.Emulsion Side药膜⾯.Encapsulating胶囊.Encroachment沾污,侵犯.End Tap封头.Entek有机护铜处理.Entrapment夹杂物.Entry Material盖板.Epoxy Resin环氧树脂.Etch Factor蚀刻因⼦.Etchant蚀刻剂(液).Etchback回蚀.Etching Indicator蚀刻指针.Etching Resist蚀刻阻剂.Eutetic Composition共融组成.Exotherm放热(曲线).Exposure曝光.Eyelet铆眼.*****F*****Fabric纲布.Face Bonding反⾯朝下结合.Failure故障.Fan Out Wiring/Fan In Wiring扇出布线/扇⼊布线. Farad 法拉.Farady法拉第.Fatigue Strength抗疲劳强度.Fault缺陷.Fault Plane断层⾯.Feed Through Hole导通孔.Feeder 进料器.Fiber Exposure玻纤显露.Fiducial Mark基准记号.Filament纤丝.Fill纬向.Filler填充料.Fillet内圆填⾓.Film底⽚.Film Adhesive接着膜,粘合膜.Filter过滤器.Fine Line细线.Fine Pitch密脚距,密线距,密垫距.Fineness粒度, 纯度.Finger⼿指.Finishing终修(饰).Finite Element Method有限要素分析法.First Article⾸产品.First Pass-Yield初检良品率.Fixture夹具.Flair刃⾓变形.Flame Point⾃燃点.Flame Resistant耐燃性.Flammability Rate燃性等级.Flare扇形崩⼝.Flash Plating闪镀.Flashover闪络.Flat Cable扁平排线.Flat Pack扁平封装(之零件).Flatness平坦度.Flexible Printed Circuit (FPC)软板.Flexural Failure挠曲损坏.Flexural Module弯曲模数, 抗挠性模数 .Flexural Strength抗挠强度.Flip Chip覆晶,扣晶.Flocculation絮凝.Flood Stroke Print覆墨冲程印刷.Flow Soldering (Wave Soldering)流焊.Fluorescence荧光.Flurocarbon Resin碳氟树脂.Flush Conductor嵌⼊式线路 , 贴平式导体.Flush Point闪⽕点.Flute退屑槽.Flux助焊剂.Foil Burr铜箔⽑边.Foil Lamination铜箔压板法.Foot残⾜(⼲膜残余物).Foot Print (Land Pattern)脚垫.Foreign Material 外来物,异物.Form-to-List布线说明清单.Four Point Twisting四点扭曲法.Free Radical⾃由基.Freeboard⼲舷.Frequency频率.Frit 玻璃熔料.Fully-Additive Process全加成法.Fungus Resistance抗霉性.Fused Coating熔锡层.Fusing熔合.Fusing Fluid助熔液.*****G*****G-10由连续玻纤所织成的玻纤布与环氧树脂粘结剂所复合成的材料.Gage, Gauge量规.Gallium Arsenide (GaAs)砷化镓.Galvanic Corrosion贾凡尼式腐蚀(电解式腐蚀).Galvanic Series贾凡尼次序(电动次序).Galvanizing镀锌.GAP第⼀⾯分离,长刃断开.Gate Array闸列,闸极数组.Gel Time胶化时间.Gelation Particle胶凝点.Gerber Data ,Gerber File格博档案(是美商Gerber公司专为PCB⾯线路图形与孔位,所发展⼀系列完整的软件档案).Ghost Image阴影.Gilding镀⾦ (现为:Glod Plating).Glass Fiber玻纤.Glass Fiber Protrusion/Gouging, Groove玻纤突出/挖破.Glass Transition Temperature, Tg玻璃态转化温度.Glaze釉⾯,釉料.Glob Top圆顶封装体.Glouble Test球状测试法.Glycol (Ethylene Glycol)⼄⼆醇.Golden Board测试⽤标准板.Grain Size结晶粒度.Grass Leak ⼤漏.Grid标准格.Ground Plane /Earth Plane接地层.Ground Plane Clearance接地空环.Guide Pin导针.Gull /Wing Lead鸥翼引脚.*****H*****Halation环晕.Half Angle半⾓.Halide卤化物.Haloing⽩圈,⽩边.Halon海龙,是CFC"氟碳化物"的⼀种商品名.Hard Anodizing硬阳极化.Hard Chrome Plating镀硬铬.Hard Soldering硬焊.Hardener (Curing Agent)硬化剂(或Curing Agent).Hardness硬度.Haring-Blum Cell海固槽.Harness电缆组合.Hay Wire跳线.Heat Cleaning烧洁.Heat Dissipation散热.Heat Distortion Point (Temp)热变形点(温度).Heat Sealing热封.Heat Sink Plane散热层.Heat Transfer Paste导热膏.Heatsink Tool散热⼯具.Hertz(Hz)赫.High Efficiency Particulate Air Filter (HEPA)⾼效空⽓尘粒过泸机. Hipot Test ⾼压电测.Hi-Rel⾼度靠度.Hit 击(钻孔时钻针每⼀次"刺下"的动作).Holding Time停置时间.Hole Breakout孔位破出.Hole Counter数孔机.Hole Density孔数密度.Hole Preparation通孔准备.Hole Pull Strength孔壁强度.Hole Void破洞.Hook 切削⼑缘外凸.Hot Air Levelling喷锡.Hot Bar Soldering热把焊接.Hot Gas Soldering热风⼿焊.HTE(High Temperature Elongation)⾼温延伸性.Hull Cell哈⽒槽.Hybrid Integrated Circuit混成电路.Hydraulic Bulge Test液压⿎起试验.Hydrogen Embrittlement氢脆.Hydrogen Overvoltage氢过(超)电压.Hydrolysis⽔解.Hydrophilic亲⽔性.Hygroscopic吸湿性.Hypersorption超吸咐.*****I*****I.C. Socket绩体电路器插座.Icicle锡尖.Illuminance照度.Image Transfer影像转移.Immersion Plating浸镀.Impedance阻抗.Impedance Match阻抗匹配.Impregnate含浸.In-Circuit Testing组装板电测.Inclusion异物,夹杂物.Indexing Hole基准孔.Inductance(L)电感.Infrared(IR)红外线.Input/Output输⼊/输出.Insert, Insertion插接.Inspection Overlay套检底⽚.Insulation Resistance绝缘电阻.Integrated Circuit(IC)绩体电路器.Inter Face接⼝.Interconnection互连.Intermetallic Compound (IMC)接⼝共化物.Internal Stress内应⼒.Interposer互边导电物.Interstitial Via-Hole(IVH)局部层间导通孔.Invar殷钢(63.8%Fe,36%Ni,0.2%C).Ion Cleanliness离⼦清洁度.Ion Exchange Resins离⼦交换树脂.Ion Migration离⼦迁移.Ionizable (Ionic) Contaimination离⼦性污染.Ionization游离,电离.Ionization Voltage (Corona Level)电离化电压(电缆内部狭缝空⽓中,引起其电离所施加之最⼩电压).IPC美国印刷电路板协会.Isolation隔离性,隔绝性.*****J*****JEDEC(Joint Electronic Device 联合电⼦组件⼯程委员会. Engineering Council)J-LeadJ型接脚.Job Shop专业⼯⼚.Joule焦⽿.Jumper Wire跳线.Junction接(合)⾯,接头.Just-In-Time(JIT)适时供应,及时出现.*****K*****Kapton聚亚醯胺软板.Karat克拉 (1克拉(钻⽯)=0.2g 纯⾦则24k⾦为100%的钝⾦.Kauri-Butanol Value考⽴丁醇值(简称K.B.值).Kerf.切形,裁剪.Kevlar聚醯胺纤维.Key电键Key Board键盘.Kiss Pressure吻压, 低压.Knoop Hardness努普硬度.Known Good Die(KGD)已知之良好芯⽚.Kovar科伐合⾦(Fe53%,Ni29%,Co17%).Kraft Paper⽜⽪纸.*****L*****Lamda Wave延伸平波.Laminar Flow平流.Laminar Structure⽚状结构.Laminate Void板材空洞.Laminate(s)基板.Lamination Void压合空洞.Laminator压膜机.Land孔环焊垫,表⾯焊垫.Landless Hole⽆环通孔.Laser Direct Imaging (LDI)雷射直接成像.Laser Maching雷射加⼯法.Laser Photogenerator(LPG), Laser Photoplotter雷射曝光机. Laser Soldering雷射焊接法.Lay Back 刃⾓磨损.Lay Out布线,布局.Lay Up 叠合.Layer to Layer Spacing层间距离Leaching焊散漂出,熔出.Lead 引脚.Lead Frame脚架.Lead Pitch脚距.Leakage Current漏电电流.Legend⽂字标记.Leveling整平.Lifted Land孔环(焊垫)浮起.Ligand错离⼦附属体.Light Emitting Diodes (LED)发光⼆极管.Light Integrator光能累积器.Light Intensity光强度.Limiting Current Density极限电流密度.Liquid Crystal Display (LCD)液晶显⽰器.Liquid Dielectrics液态介质.Liquid Photoimagible Solder Mask, (LPSM)液态感光防焊绿漆. Local Area Network区域性⽹络.Logic 逻辑.Logic Circuit 逻辑电路.Loss Factor损失因素.Loss Tangent (TanδDK)损失正切.Lot Size批量.Luminance发光强度.Lyophilic亲⽔性胶体.*****M*****Macro-Throwing Power巨观分布⼒.Major Defect主要(严重)缺点.Major Weave Direction主要织向.Margin刃带(钻头尖部).Marking标记.Mask阻剂.Mass Finishing⼤量整⾯(拋光).Mass Lamination⼤型压板.Mass Transport质量输送.Master Drawing主图.Mat席(⽤于CEM-3(Composite Epoxy Material)的复合材料.)Matte Side⽑⾯(电镀铜⽪(ED Foil)之粗糙⾯).Mealing泡点.Mean Time To Failure (MTTF)故障前可⽤之平均时数. Measling⽩点.Mechanical Stretcher机械式张⽹机.Mechanical Warp机械式缠绕.Mechanism机理.Membrane Switch薄膜开关.Meniscograph Test弧⾯状沾锡试验.Meniscus弯⽉⾯.Mercury Vaper Lamp汞⽓灯.Mesh Count纲⽬数.Metal Halide Lamp ⾦属卤素灯.Metallization⾦属化.Metallized Fabric⾦属化纲布.Micro Wire Board微封线板.Micro-electronios微电⼦.Microetching微蚀.Microsectioning微切⽚法.Microstrip 微条.Microstrip Line微条线,微带线.Microthrowing Power微分布⼒.Microwave微波.Migration迁移.Migration Rate迁移率.Mil英丝.Minimum Annular Ring孔环下限.Minimum Electrical Spacing电性间距下限.Minor Weave Direction次要织向.Misregistration 对不准度.Mixed Componmt Mounting Technology混合零件之组装技术. Modem调变及解调器.Modification修改.Module模块.Modulus of Elasticity弹性系数.Moisture and Insulation Resistance Test湿⽓与绝缘电阻试验. Mold Release 脱模剂,离型剂.Mole摩尔.Monofilament单丝.Mother Board主机板,母板.Moulded Circuit模造⽴体电路机.Mounting Hole安装孔.Mounting Hole组装孔,机装孔.Mouse Bite⿏齿(蚀刻后线路边缘出现不规则缺⼝).Multi-Chip-Module(MCM)多芯⽚芯⽚模块.Multiwiring Board (or Discrete Wiring Board)复线板.*****N*****N.C.数值控制.Nail Head钉头.Near IR近红外线.Negative负⽚,钻尖的第⼀⾯外缘变窄.Negative Etch-back反回蚀.Negative Stencil负性感光膜.Negative-Acting Resist负性作⽤之阻剂.Network纲状元件.Newton⽜顿.Newton Ring ⽜顿环.Newtonian Liquid⽜顿流体.Nick缺⼝.N-Methyl Pyrrolidine (NMP)N-甲基四氢哔咯.Noble Metal Paste贵⾦属印膏.Node节点.Nodule节瘤.Nomencleature标⽰⽂字符号.Nominal Cured Thickness标⽰厚度.Non-Circular Land⾮圆形孔环焊垫.Non-flammable⾮燃性.Non-wetting不沾锡.Normal Concentration (Strength)标准浓度,当量浓度. Normal Distribution常态分布.Novolac酯醛树脂.Nucleation , Nucleating核化.Numerical Control数值控制.Nylon尼龙.Occlusion吸藏.Off-Contact架空.Offset第⼀⾯⼤⼩不均.OFHC(Oxyen Free High Conductivity)⽆氧⾼导电铜. Ohm欧姆.Oilcanning盖板弹动.OLB(Outer Lead Bond)外引脚结合.Oligomer寡聚物.Omega Meter离⼦污染检测仪.Omega Wave振荡波.On-Contact Printing密贴式印刷.Opaquer不透明剂,遮光剂.Open Circuits断线.Optical Comparater光学对⽐器(光学放⼤器.) Optical Density光密度.Optical Inspection光学检验.Optical Instrument光学仪器.Organic Solderability Preservatives (OSP)有机保焊剂. Osmosis渗透.Outgassing出⽓,吹⽓.Outgrowth悬出,横出,侧出.Output产出,输出.Overflow溢流.Overhang总悬空.Overlap 钻尖点分离.Overpotantial(Over voltage)过电位,过电压. Oxidation氧化.Oxygen Inhibitor氧化抑制剂.Ozone Depletion臭氧层耗损.*****P*****Packaging封装,构装.Pad焊垫,圆垫.Pad Master圆垫底⽚.Pads Only Board唯垫板.Palladium钯.Panel制程板.Panel Plating全板镀铜.Panel Process全板电镀法.Paper Phenolic纸质酚醛树脂(板材).Parting Agent脱膜剂.Passivation钝化 ,钝化外理.Passive Device (Component)被动组件(零件)Paste膏,糊.Pattern板⾯图形.Pattern Plating线路电镀.Pattern Process线路电镀法.Peak Voltage峰值电压.Peel Strength抗撕强度.Periodic Reverse (PR) Current周期性反电流. Peripheral周边附属设备.Permeability透⽓性,导磁率.Permittivity诱电率,透电率.pH Value酸碱值.Phase相.Phase Diagram相图.Phenolic酚醛树脂.Photofugitive感光褪⾊.Photographic film感光成像之底⽚.Photoinitiator感光启始剂.Photomask光罩.Photoplotter, Plotter光学绘图机.。
PCB电子线路板专业术语
PCB电子线路板专业术语一、综合词汇1、印制电路：printed circuit2、印制线路：printed wiring3、印制板：printed board4、印制板电路：printed circuit board (PCB)5、印制线路板：printed wiring board(PWB)6、印制元件：printed component7、印制接点：printed contact8、印制板装配：printed board assembly9、板：board10、单面印制板：single-sided printed board(SSB)11、双面印制板：double-sided printed board(DSB)12、多层印制板：mulitlayer printed board(MLB)13、多层印制电路板：mulitlayer printed circuit board14、多层印制线路板：mulitlayer prited wiring board15、刚性印制板：rigid printed board16、刚性单面印制板：rigid single-sided printed borad17、刚性双面印制板：rigid double-sided printed borad18、刚性多层印制板：rigid multilayer printed board19、挠性多层印制板：flexible multilayer printed board20、挠性印制板：flexible printed board21、挠性单面印制板：flexible single-sided printed board22、挠性双面印制板：flexible double-sided printed board23、挠性印制电路：flexible printed circuit (FPC)24、挠性印制线路：flexible printed wiring25、刚性印制板：flex-rigid printed board, rigid-flex printed board26、刚性双面印制板：flex-rigid double-sided printed board, rigid-flex double-sided printed27、刚性多层印制板：flex-rigid multilayer printed board, rigid-flex multilayer printed board28、齐平印制板：flush printed board29、金属芯印制板：metal core printed board30、金属基印制板：metal base printed board31、多重布线印制板：mulit-wiring printed board32、陶瓷印制板：ceramic substrate printed board33、导电胶印制板：electroconductive paste printed board34、模塑电路板：molded circuit board35、模压印制板：stamped printed wiring board36、顺序层压多层印制板：sequentially-laminated mulitlayer37、散线印制板：discrete wiring board38、微线印制板：micro wire board39、积层印制板：buile-up printed board40、积层多层印制板：build-up mulitlayer printed board (BUM)41、积层挠印制板：build-up flexible printed board42、表面层合电路板：surface laminar circuit (SLC)43、埋入凸块连印制板：B2it printed board44、多层膜基板：multi-layered film substrate(MFS)45、层间全内导通多层印制板：ALIVH multilayer printed board46、载芯片板：chip on board (COB)47、埋电阻板：buried resistance board48、母板：mother board49、子板：daughter board50、背板：backplane51、裸板：bare board52、键盘板夹心板：copper-invar-copper board53、动态挠性板：dynamic flex board54、静态挠性板：static flex board55、可断拼板：break-away planel56、电缆：cable57、挠性扁平电缆：flexible flat cable (FFC)58、薄膜开关：membrane switch59、混合电路：hybrid circuit60、厚膜：thick film61、厚膜电路：thick film circuit62、薄膜：thin film63、薄膜混合电路：thin film hybrid circuit64、互连：interconnection65、导线：conductor trace line66、齐平导线：flush conductor67、传输线：transmission line68、跨交：crossover69、板边插头：edge-board contact70、增强板：stiffener71、基底：substrate72、基板面：real estate73、导线面：conductor side74、元件面：component side75、焊接面：solder side76、印制：printing77、网格：grid78、图形：pattern79、导电图形：conductive pattern80、非导电图形：non-conductive pattern81、字符：legend82、标志：mark二、基材：1、基材：base material2、层压板：laminate3、覆金属箔基材：metal-clad bade material4、覆铜箔层压板：copper-clad laminate (CCL)5、单面覆铜箔层压板：single-sided copper-clad laminate6、双面覆铜箔层压板：double-sided copper-clad laminate7、复合层压板：composite laminate8、薄层压板：thin laminate9、金属芯覆铜箔层压板：metal core copper-clad laminate10、金属基覆铜层压板：metal base copper-clad laminate11、挠性覆铜箔绝缘薄膜：flexible copper-clad dielectric film12、基体材料：basis material13、预浸材料：prepreg14、粘结片：bonding sheet15、预浸粘结片：preimpregnated bonding sheer16、环氧玻璃基板：epoxy glass substrate17、加成法用层压板：laminate for additive process18、预制内层覆箔板：mass lamination panel19、内层芯板：core material20、催化板材：catalyzed board ,coated catalyzed laminate21、涂胶催化层压板：adhesive-coated catalyzed laminate22、涂胶无催层压板：adhesive-coated uncatalyzed laminate23、粘结层：bonding layer24、粘结膜：film adhesive25、涂胶粘剂绝缘薄膜：adhesive coated dielectric film26、无支撑胶粘剂膜：unsupported adhesive film27、覆盖层：cover layer (cover lay)28、增强板材：stiffener material29、铜箔面：copper-clad surface30、去铜箔面：foil removal surface31、层压板面：unclad laminate surface32、基膜面：base film surface33、胶粘剂面：adhesive faec34、原始光洁面：plate finish35、粗面：matt finish36、纵向：length wise direction37、模向：cross wise direction38、剪切板：cut to size panel39、酚醛纸质覆铜箔板：phenolic cellulose paper copper-clad laminates(phenolic/paper CCL)40、环氧纸质覆铜箔板：epoxide cellulose paper copper-clad laminates (epoxy/paper CCL)41、环氧玻璃布基覆铜箔板：epoxide woven glass fabric copper-clad laminates42、环氧玻璃布纸复合覆铜箔板：epoxide cellulose paper core, glasscloth surfaces copper-clad laminates43、环氧玻璃布玻璃纤维复合覆铜箔板：epoxide non woven/woven glass reinforced copper-clad laminates44、聚酯玻璃布覆铜箔板：ployester woven glass fabric copper-clad laminates45、聚酰亚胺玻璃布覆铜箔板：polyimide woven glass fabric copper-clad laminates46、双马来酰亚胺三嗪环氧玻璃布覆铜箔板：bismaleimide/triazine/epoxide woven glass fabric copper-clad lamimates 47、环氧合成纤维布覆铜箔板：epoxide synthetic fiber fabric copper-clad laminates48、聚四乙烯玻璃纤维覆铜箔板：teflon/fiber glass copper-clad laminates49、超薄型层压板：ultra thin laminate50、陶瓷基覆铜箔板：ceramics base copper-clad laminates51、紫外线阻挡型覆铜箔板：UV blocking copper-clad laminates三、基材的材料1、A阶树脂：A-stage resin2、B阶树脂：B-stage resin3、C阶树脂：C-stage resin4、环氧树脂：epoxy resin5、酚醛树脂：phenolic resin6、聚酯树脂：polyester resin7、聚酰亚胺树脂：polyimide resin8、双马来酰亚胺三嗪树脂：bismaleimide-triazine resin9、丙烯酸树脂：acrylic resin10、三聚氰胺甲醛树脂：melamine formaldehyde resin11、多官能环氧树脂：polyfunctional epoxy resin12、溴化环氧树脂：brominated epoxy resin13、环氧酚醛：epoxy novolac14、氟树脂：fluroresin15、硅树脂：silicone resin16、硅烷：silane17、聚合物：polymer18、无定形聚合物：amorphous polymer19、结晶现象：crystalline polamer20、双晶现象：dimorphism21、共聚物：copolymer22、合成树脂：synthetic23、热固性树脂：thermosetting resin24、热塑性树脂：thermoplastic resin25、感光性树脂：photosensitive resin26、环氧当量：weight per epoxy equivalent (WPE)27、环氧值：epoxy value28、双氰胺：dicyandiamide29、粘结剂：binder30、胶粘剂：adesive31、固化剂：curing agent32、阻燃剂：flame retardant33、遮光剂：opaquer34、增塑剂：plasticizers35、不饱和聚酯：unsatuiated polyester36、聚酯薄膜：polyester37、聚酰亚胺薄膜：polyimide film (PI)38、聚四氟乙烯：polytetrafluoetylene (PTFE)39、聚全氟乙烯丙烯薄膜：perfluorinated ethylene-propylene copolymer film (FEP)40、增强材料：reinforcing material41、玻璃纤维：glass fiber42、E玻璃纤维：E-glass fibre43、D玻璃纤维：D-glass fibre44、S玻璃纤维：S-glass fibre45、玻璃布：glass fabric46、非织布：non-woven fabric47、玻璃纤维垫：glass mats48、纱线：yarn49、单丝：filament50、绞股：strand51、纬纱：weft yarn52、经纱：warp yarn53、但尼尔：denier54、经向：warp-wise55、纬向：weft-wise, filling-wise56、织物经纬密度：thread count57、织物组织：weave structure58、平纹组织：plain structure59、坏布：grey fabric60、稀松织物：woven scrim61、弓纬：bow of weave62、断经：end missing63、缺纬：mis-picks64、纬斜：bias65、折痕：crease66、云织：waviness67、鱼眼：fish eye68、毛圈长：feather length69、厚薄段：mark70、裂缝：split71、捻度：twist of yarn72、浸润剂含量：size content73、浸润剂残留量：size residue74、处理剂含量：finish level75、浸润剂：size76、偶联剂：couplint agent77、处理织物：finished fabric78、聚酰胺纤维：polyarmide fiber79、聚酯纤维非织布：non-woven polyester fabric80、浸渍绝缘纵纸：impregnating insulation paper81、聚芳酰胺纤维纸：aromatic polyamide paper82、断裂长：breaking length83、吸水高度：height of capillary rise84、湿强度保留率：wet strength retention85、白度：whitenness86、陶瓷：ceramics87、导电箔：conductive foil88、铜箔：copper foil89、电解铜箔：electrodeposited copper foil (ED copper foil)90、压延铜箔：rolled copper foil91、退火铜箔：annealed copper foil92、压延退火铜箔：rolled annealed copper foil (RA copper foil)93、薄铜箔：thin copper foil94、涂胶铜箔：adhesive coated foil95、涂胶脂铜箔：resin coated copper foil (RCC)96、复合金属箔：composite metallic material97、载体箔：carrier foil98、殷瓦：invar99、箔（剖面）轮廓：foil profile100、光面：shiny side101、粗糙面：matte side102、处理面：treated side103、防锈处理：stain proofing104、双面处理铜箔：double treated foil四、设计1、原理图：shematic diagram2、逻辑图：logic diagram3、印制线路布设：printed wire layout4、布设总图：master drawing5、可制造性设计：design-for-manufacturability6、计算机辅助设计：computer-aided design.(CAD)7、计算机辅助制造：computer-aided manufacturing.(CAM)8、计算机集成制造：computer integrat manufacturing.(CIM)9、计算机辅助工程：computer-aided engineering.(CAE)10、计算机辅助测试：computer-aided test.(CAT)11、电子设计自动化：electric design automation .(EDA)12、工程设计自动化：engineering design automaton .(EDA2)13、组装设计自动化：assembly aided architectural design. (AAAD)14、计算机辅助制图：computer aided drawing15、计算机控制显示：computer controlled display .(CCD)16、布局：placement17、布线：routing18、布图设计：layout19、重布：rerouting20、模拟：simulation21、逻辑模拟：logic simulation22、电路模拟：circit simulation23、时序模拟：timing simulation24、模块化：modularization25、布线完成率：layout effeciency26、机器描述格式：machine descriptionm format .(MDF)27、机器描述格式数据库：MDF databse28、设计数据库：design database29、设计原点：design origin30、优化（设计）：optimization (design)31、供设计优化坐标轴：predominant axis32、表格原点：table origin33、镜像：mirroring34、驱动文件：drive file35、中间文件：intermediate file36、制造文件：manufacturing documentation37、队列支撑数据库：queue support database38、元件安置：component positioning39、图形显示：graphics dispaly40、比例因子：scaling factor41、扫描填充：scan filling42、矩形填充：rectangle filling43、填充域：region filling44、实体设计：physical design45、逻辑设计：logic design46、逻辑电路：logic circuit47、层次设计：hierarchical design48、自顶向下设计：top-down design49、自底向上设计：bottom-up design50、线网：net51、数字化：digitzing52、设计规则检查：design rule checking53、走（布）线器：router (CAD)54、网络表：net list55、计算机辅助电路分析：computer-aided circuit analysis56、子线网：subnet57、目标函数：objective function58、设计后处理：post design processing (PDP)59、交互式制图设计：interactive drawing design60、费用矩阵：cost metrix61、工程图：engineering drawing62、方块框图：block diagram63、迷宫：moze64、元件密度：component density65、巡回售货员问题：traveling salesman problem66、自由度：degrees freedom67、入度：out going degree68、出度：incoming degree69、曼哈顿距离：manhatton distance70、欧几里德距离：euclidean distance71、网络：network72、阵列：array73、段：segment74、逻辑：logic75、逻辑设计自动化：logic design automation76、分线：separated time77、分层：separated layer78、定顺序：definite sequence五、形状与尺寸：1、导线（通道）：conduction (track)2、导线（体）宽度：conductor width3、导线距离：conductor spacing4、导线层：conductor layer5、导线宽度/间距：conductor line/space6、第一导线层：conductor layer No.17、圆形盘：round pad8、方形盘：square pad9、菱形盘：diamond pad10、长方形焊盘：oblong pad11、子弹形盘：bullet pad12、泪滴盘：teardrop pad13、雪人盘：snowman pad14、V形盘：V-shaped pad15、环形盘：annular pad16、非圆形盘：non-circular pad17、隔离盘：isolation pad18、非功能连接盘：monfunctional pad19、偏置连接盘：offset land20、腹（背）裸盘：back-bard land21、盘址：anchoring spaur22、连接盘图形：land pattern23、连接盘网格阵列：land grid array24、孔环：annular ring25、元件孔：component hole26、安装孔：mounting hole27、支撑孔：supported hole28、非支撑孔：unsupported hole29、导通孔：via30、镀通孔：plated through hole (PTH)31、余隙孔：access hole32、盲孔：blind via (hole)33、埋孔：buried via hole34、埋/盲孔：buried /blind via35、任意层内部导通孔：any layer inner via hole (ALIVH)36、全部钻孔：all drilled hole37、定位孔：toaling hole38、无连接盘孔：landless hole39、中间孔：interstitial hole40、无连接盘导通孔：landless via hole41、引导孔：pilot hole42、端接全隙孔：terminal clearomee hole43、准表面间镀覆孔：quasi-interfacing plated-through hole44、准尺寸孔：dimensioned hole45、在连接盘中导通孔：via-in-pad46、孔位：hole location47、孔密度：hole density48、孔图：hole pattern49、钻孔图：drill drawing50、装配图：assembly drawing51、印制板组装图：printed board assembly drawing52、参考基准：datum referan更多的详细资料来源：。
PCB工程部专业英语词汇(参考模板)
PCB 工程部专业英文词汇词汇1.板料: material2.最低限度: minimum 或者min.3.最大限度: maximum 或者max.4.基准点(零点) datum point5.周期Date code6.V-cut余厚V-cut remain thickness7.抢电铜皮（假铜）dummy copper8.实物板actual board9.外形及尺寸错误dimension error10.异常情形error data file11.焊锡面与零件面对位偏差misregistration12.孔塞plug hole13.要求requirement14.缺少miss15.偏公差uneven tolerance16.补偿compensation17.表面处理surface treatment18.无铅喷锡Lead free HAL19.金手指斜边bevel of G/F20.制程能力process capability21.建议,暗示suggest22.确保ensure23.满足,达到meet24.为了in order to25.交货期delivery date26.绿油桥solder mask bridge 或者solder mask dam27.根据according to 28.单边3mil per side 3 mil29.直径diameter30.半径radius31.小于3mil less than 3mil32.高于3mil more than 3 mil33.压合结构stacking structure 或者stack_up34.附件：attached file35.样品：sample36.文档：Document37.答复：answer; reply38.规格：spec39.与...同样的：the same as40.前版本：previous version(old version)41.生产：production42.确认：confirm43.再次确认：confirm again44.工程问题：engineering query（EQ）45.尽快：as soon as possible46.生产文件：production Gerber47.联系某人：contact somebody48.提交样板：submit sample49.交货期：delivery date50.电测成本：ET（electrical test）cost51.通断测试：Open and short testing52.参考：refer to53.IPC标准：IPC standard54.IPC二级：IPC class 255.可接受的：acceptable56.允许：permit57.制造：manufacture 或者fabricate58.修改：revision59.公差：tolerance60.忽略：ignore61.工具孔：tooling hole62.安装孔：mounting hole63.元件孔：component hole64.槽孔：slot hole65.邮票孔：snap off hole 或者stamp hole66.导通孔：via hole67.盲孔：blind via hole68.埋孔：buried via hole69.金属化孔：PTH(plated through hole)70.非金属化孔：NPTH( no plated through hole)71.孔位：hole location72.避免：avoid73.原设计：original design74.修改：modify75.按原设计：follow up original design76.附边：waste tab, waste area 或者breakaway tab77.铜条：copper strip78.拼板：panel drawing79.板厚：board thickness80.删除：remove(delete)81.削铜：shave the copper82.露铜：copper exposure 或者exposed copper83.光标点: fiducial mark84.不同：be different from(differ from)85.内弧：inside radius86.焊环：annular ring87.单板尺寸：single size 88.拼板尺寸：panel size89.铣,锣：routing90.铣刀：router 或者Routing bit91.楔形掏槽V-cut 或者V scoring92.哑光：matt93.光亮的：glossy94.锡珠：solder ball(solder plugs)95.阻焊：solder mask(solder resist)96.阻焊开窗：solder mask opening97.单面开窗：single side mask opening98.补油：touch up solder mask99.补线：track welds100.毛刺：burrs101.去毛刺：deburr102.镀层厚度：plating thickness103.清洁度：cleanliness104.离子污染：ionic contamination105.阻燃性等级：flammability retardant rating 106.黑化：black oxidation107.棕化：brown oxidation108.红化：red oxidation109.可焊性不良：poor solderability110.焊料：solder111.包装：packaging112.角标：corner mark113.特性阻抗：characteristic impedance 114.正像：positive115.负片：negative116.镜像：mirror117.线宽：line width 或者trace width118.线距：line spacing 或者trace spacing119.做样：build sample120.按照：according to121.成品：finished122.做变更：make the change123.相类似：similar to124.规格：specification125.下移：shift down126.垂直地：vertically127.水平的：horizontally128.增大：increase129.缩小：decrease130.表面处理：Surface Finishing131.波峰焊：wave solder132.钻孔数据：drilling data133.标记：Logo134.Ul 标记：UL logo,或者Ul Marking135.蚀刻标记：etched marking136.周期：date code137.翘曲：bow and twist138.外层：outer layer 或者external layer139.内层：inner layer 或者internal layer140.顶层：top layer141.底层：bottom layer142.元件面：component side143.焊接面：solder side144.阻焊层：solder mask layer145.字符层：legend layer (silkscreen layer or over layer) 146.兰胶层：peelable SM layer147.贴片层：paste mask layer 148.碳油层：carbon layer149.外形层：outline layer(profile layer)150.白油：white ink151.绿油：green ink152.喷锡：hot air leveling (HAL)153.电金,水金：flash gold154.插头镀金：plated gold edge-board contacts 155.金手指：Gold-finger156.防氧化：Entek (OSP)157.沉金：Immersion gold (chem. Gold)158.沉锡：Immersion Tin(chem.Tin)159.沉银：Immersion Silver (chem. silver) 160.单面板：single sided board161.双面板：double sided board162.多层板：multilayer board163.刚性板：rigid board164.挠性板：flexible board165.刚挠板：flex-rigid board166.铣：CNC (mill , routing)167.冲：punching168.倒角：beveling169.斜面：chamfer170.倒圆角：fillet171.尺寸：dimension172.材料：material173.介电常数：Dielectric constant174.菲林：film175.成像：Imaging176.板镀：Panel Plating177.图镀：Pattern Plating178.后清洗：Final Cleaning179.叠层：stacking structure (stack-up) 180.污染焊盘：contaminate pad181.分孔图：drill chart 或者drill map 182.度数：degree183.被…覆盖：be covered with184.负公差：minus tolerance185.标靶盘：target pad186.外形公差：routing tolerance 187.芯板：core188.半固化片Prepreg189.阻抗线：impedance trace190.评估estimate191.玻纤显露Fiber Exposure192.底铜base copper193.工作搞working Gerber194.原稿original art work195.放宽relax196.挖空blanking 或者cut-out 197.一般性阻焊油墨general resist ink 198.孔位错误mis hole location 199.压合周期press cycle200.毛边serrated edges201.跳印skip printing202.气泡blistering203.隔离焊盘isolated pad204.泪滴tear drops205.箭头arrows206.加大Enlarge207.压合周期press cycle 208.毛边serrated edges209.跳印,漏印skip printing210.宽度与厚度的比值width-to-thickness ratio 211.调整adjust212.铜箔基板copper claded laminates213.线路露铜copper exposure214.孔内异物dirty hole215.椭圆形elliptical set216.纤维突出fiber protrusion217.填充料filler218.互相连通interconnection219.改善方案implementation220.板料使用率material use factor221.回路,网络network222.缺口nick223.氧化oxidation224.剥离(剥落) peeling off225.补线不良poor touch-up226.品质等级quality classification227.对位孔registration228.拒收rejectable229.树脂含量resin content230.排列电阻resistor network231.锣刀（铣刀）routing bit232.孔内沾文字S/L on hole233.孔内绿漆S/M on hole234.线路沾锡solder on trace235.金手指沾锡solder on G/F236.废框scrap237.封孔处理sealing238.间距不足spacing non-enough239.靶位孔target hole240.测试线路test circuit241.热应力试验thermal stress242.厚度分布thickness distribution243.薄基板,内层板thin core244.线路缺口及针孔track nick & pin hole245.裁切线trim line246.真平整true leveling247.真正位置的孔true position248.万用型universal249.气化室vaporizer250.仓库warehouse251.契尖角wedge angle252.线细width reduce253.良率yield254.渗铜,渗入,灯芯效应wicking255.允收acceptable256.试样点coupon location257.经核准的，被认可的approved258.超越胜过,超过其他exceed259.牛皮纸kraft paper260.孔壁破铜Hole void261.孔位破出Hole breakoutPCB生产—经典流程—英文培训教程A. 开料( Cut Lamination)a-1 裁板( Sheets Cutting)a-2 原物料发料(Panel)(Shear material to Size) B. 钻孔(Drilling)b-1 内钻(Inner Layer Drilling )b-2 一次孔(Outer Layer Drilling )b-3 二次孔(2nd Drilling)b-4 雷射钻孔(Laser Drilling )(Laser Ablation )b-5 盲(埋)孔钻孔(Blind & Buried Hole Drilling)C. 干膜制程( Photo Process(D/F))c-1 前处理(Pretreatment)c-2 压膜(Dry Film Lamination)c-3 曝光(Exposure)c-4 显影(Developing)c-5 蚀铜(Etching)c-6 去膜(Stripping)c-7 初检( Touch-up)c-8 化学前处理,化学研磨( Chemical Milling )c-9 选择性浸金压膜(Selective Gold Dry Film Lamination) c-10 显影(Developing )c-11 去膜(Stripping )Developing , Etching & Stripping ( DES )D. 压合Laminationd-1 黑化(Black Oxide Treatment)d-2 微蚀(Microetching)d-3 铆钉组合(eyelet )d-4 叠板(Lay up)d-5 压合(Lamination)d-6 后处理(Post Treatment)d-7 黑氧化( Black Oxide Removal )d-8 铣靶(spot face)d-9 去溢胶(resin flush removal)E. 减铜(Copper Reduction)e-1 薄化铜(Copper Reduction)F. 电镀(Horizontal Electrolytic Plating)f-1 水平电镀(Horizontal Electro-Plating) (Panel Plating) f-2 锡铅电镀( Tin-Lead Plating ) (Pattern Plating)f-3 低于1 mil ( Less than 1 mil Thickness )f-4 高于1 mil ( More than 1 mil Thickness)f-5 砂带研磨(Belt Sanding)f-6 剥锡铅( Tin-Lead Stripping)f-7 微切片( Microsection)G. 塞孔(Plug Hole)g-1 印刷( Ink Print )g-2 预烤(Precure)g-3 表面刷磨(Scrub)g-4 后烘烤(Postcure)H. 防焊(绿漆/绿油): (Solder Mask)h-1 C面印刷(Printing Top Side)h-2 S面印刷(Printing Bottom Side)h-3 静电喷涂(Spray Coating)h-4 前处理(Pretreatment)h-5 预烤(Precure)h-6 曝光(Exposure)h-7 显影(Develop)h-8 后烘烤(Postcure)h-9 UV烘烤(UV Cure)h-10 文字印刷( Printing of Legend )h-11 喷砂( Pumice)(Wet Blasting)h-12 印可剥离防焊(Peelable Solder Mask)I . 镀金Gold platingi-1 金手指镀镍金( Gold Finger )i-2 电镀软金(Soft Ni/Au Plating)i-3 浸镍金( Immersion Ni/Au) (Electroless Ni/Au)J. 喷锡(Hot Air Solder Leveling)j-1 水平喷锡(Horizontal Hot Air Solder Leveling)j-2 垂直喷锡( Vertical Hot Air Solder Leveling)j-3 超级焊锡(Super Solder )j-4. 印焊锡突点(Solder Bump)K. 成型(Profile)(Form)k-1 捞型(N/C Routing ) (Milling)k-2 模具冲(Punch)k-3 板面清洗烘烤(Cleaning & Backing)k-4 V型槽( V-Cut)(V-Scoring)k-5 金手指斜边( Beveling of G/F)L. 开短路测试(Electrical Testing) (Continuity & Insulation Testing) l-1 AOI 光学检查( AOI Inspection)l-2 VRS 目检(Verified & Repaired)l-3 泛用型治具测试(Universal Tester)l-4 专用治具测试(Dedicated Tester)l-5 飞针测试(Flying Probe)M. 终检( Final Visual Inspection)m-1 压板翘( Warpage Remove)m-2 X-OUT 印刷(X-Out Marking)m-3 包装及出货(Packing & shipping)m-4 目检( Visual Inspection)m-5 清洗及烘烤( Final Clean & Baking)m-6 护铜剂(ENTEK Cu-106A)(OSP)m-7 离子残余量测试(Ionic Contamination Test )(Cleanliness Test)m-8 冷热冲击试验(Thermal cycling Testing)m-9 焊锡性试验( Solderability Testing )N. 雷射钻孔(Laser Ablation)N-1 雷射钻Tooling孔(Laser ablation Tooling Hole)N-2 雷射曝光对位孔(Laser Ablation Registration Hole)N-3 雷射Mask制作(Laser Mask)N-4 雷射钻孔(Laser Ablation) N-5 AOI 检查及VRS ( AOI Inspection & Verified & Repaired)N-6 Blaser AOI (after Desmear and Microetching) N-7 除胶渣(Desmear)N-8 微蚀(Microetching )---精心整理，希望对您有所帮助。
pcb专业术语
一、综合词汇CAM(computer Aided Manufacturing1、印制电路：printed circuit2、印制线路：printed wiring3、印制板：printed board4、印制板电路：printed circuit board (pcb)5、印制线路板：printed wiring board(pwb)6、印制元件：printed component7、印制接点：printed contact8、印制板装配：printed board assembly9、板：board10、单面印制板：single-sided printed board(ssb)11、双面印制板：double-sided printed board(dsb)12、多层印制板：mulitlayer printed board(mlb)13、多层印制电路板：mulitlayer printed circuit board14、多层印制线路板：mulitlayer prited wiring board15、刚性印制板：rigid printed board16、刚性单面印制板：rigid single-sided printed borad17、刚性双面印制板：rigid double-sided printed borad18、刚性多层印制板：rigid multilayer printed board19、挠性多层印制板：flexible multilayer printed board20、挠性印制板：flexible printed board21、挠性单面印制板：flexible single-sided printed board22、挠性双面印制板：flexible double-sided printed board23、挠性印制电路：flexible printed circuit (fpc)24、挠性印制线路：flexible printed wiring25、刚性印制板：flex-rigid printed board, rigid-flex printed board26、刚性双面印制板：flex-rigid double-sided printed board, rigid-flex double-sided printed27、刚性多层印制板：flex-rigid multilayer printed board, rigid-flex multilayer printed board28、齐平印制板：flush printed board29、金属芯印制板：metal core printed board30、金属基印制板：metal base printed board31、多重布线印制板：mulit-wiring printed board32、陶瓷印制板：ceramic substrate printed board33、导电胶印制板：electroconductive paste printed board34、模塑电路板：molded circuit board35、模压印制板：stamped printed wiring board36、顺序层压多层印制板：sequentially-laminated mulitlayer37、散线印制板：discrete wiring board38、微线印制板：micro wire board39、积层印制板：buile-up printed board40、积层多层印制板：build-up mulitlayer printed board (bum)41、积层挠印制板：build-up flexible printed board42、表面层合电路板：surface laminar circuit (slc)43、埋入凸块连印制板：b2it printed board44、多层膜基板：multi-layered film substrate(mfs)45、层间全内导通多层印制板：alivh multilayer printed board46、载芯片板：chip on board (cob)47、埋电阻板：buried resistance board48、母板：mother board49、子板：daughter board50、背板：backplane51、裸板：bare board52、键盘板夹心板：copper-invar-copper board53、动态挠性板：dynamic flex board54、静态挠性板：static flex board55、可断拼板：break-away planel56、电缆：cable57、挠性扁平电缆：flexible flat cable (ffc)58、薄膜开关：membrane switch59、混合电路：hybrid circuit60、厚膜：thick film61、厚膜电路：thick film circuit62、薄膜：thin film63、薄膜混合电路：thin film hybrid circuit64、互连：interconnection65、导线：conductor trace line66、齐平导线：flush conductor67、传输线：transmission line68、跨交：crossover69、板边插头：edge-board contact70、增强板：stiffener71、基底：substrate72、基板面：real estate73、导线面：conductor side74、元件面：component side75、焊接面：solder side76、印制：printing77、网格：grid78、图形：pattern79、导电图形：conductive pattern80、非导电图形：non-conductive pattern81、字符：legend82、标志：mark二、基材：1、基材：base material2、层压板：laminate3、覆金属箔基材：metal-clad bade material4、覆铜箔层压板：copper-clad laminate (ccl)5、单面覆铜箔层压板：single-sided copper-clad laminate6、双面覆铜箔层压板：double-sided copper-clad laminate7、复合层压板：composite laminate8、薄层压板：thin laminate9、金属芯覆铜箔层压板：metal core copper-clad laminate10、金属基覆铜层压板：metal base copper-clad laminate11、挠性覆铜箔绝缘薄膜：flexible copper-clad dielectric film12、基体材料：basis material13、预浸材料：prepreg14、粘结片：bonding sheet15、预浸粘结片：preimpregnated bonding sheer16、环氧玻璃基板：epoxy glass substrate17、加成法用层压板：laminate for additive process18、预制内层覆箔板：mass lamination panel19、内层芯板：core material20、催化板材：catalyzed board ,coated catalyzed laminate21、涂胶催化层压板：adhesive-coated catalyzed laminate22、涂胶无催层压板：adhesive-coated uncatalyzed laminate23、粘结层：bonding layer24、粘结膜：film adhesive25、涂胶粘剂绝缘薄膜：adhesive coated dielectric film26、无支撑胶粘剂膜：unsupported adhesive film27、覆盖层：cover layer (cover lay)28、增强板材：stiffener material29、铜箔面：copper-clad surface30、去铜箔面：foil removal surface31、层压板面：unclad laminate surface32、基膜面：base film surface33、胶粘剂面：adhesive faec34、原始光洁面：plate finish35、粗面：matt finish36、纵向：length wise direction37、模向：cross wise direction38、剪切板：cut to size panel39、酚醛纸质覆铜箔板：phenolic cellulose paper copper-clad laminates(phenolic/paper ccl)40、环氧纸质覆铜箔板：epoxide cellulose paper copper-clad laminates (epoxy/paper ccl)41、环氧玻璃布基覆铜箔板：epoxide woven glass fabric copper-clad laminates42、环氧玻璃布纸复合覆铜箔板：epoxide cellulose paper core, glass cloth surfaces copper-clad laminates43、环氧玻璃布玻璃纤维复合覆铜箔板：epoxide non woven/woven glass reinforced copper-clad laminates44、聚酯玻璃布覆铜箔板：ployester woven glass fabric copper-clad laminates45、聚酰亚胺玻璃布覆铜箔板：polyimide woven glass fabric copper-clad laminates46、双马来酰亚胺三嗪环氧玻璃布覆铜箔板：bismaleimide/triazine/epoxide woven glass fabric copper-clad lamimates47、环氧合成纤维布覆铜箔板：epoxide synthetic fiber fabric copper-clad laminates48、聚四乙烯玻璃纤维覆铜箔板：teflon/fiber glass copper-clad laminates49、超薄型层压板：ultra thin laminate50、陶瓷基覆铜箔板：ceramics base copper-clad laminates51、紫外线阻挡型覆铜箔板：uv blocking copper-clad laminates三、基材的材料1、a阶树脂：a-stage resin2、b阶树脂：b-stage resin3、c阶树脂：c-stage resin4、环氧树脂：epoxy resin5、酚醛树脂：phenolic resin6、聚酯树脂：polyester resin7、聚酰亚胺树脂：polyimide resin8、双马来酰亚胺三嗪树脂：bismaleimide-triazine resin9、丙烯酸树脂：acrylic resin10、三聚氰胺甲醛树脂：melamine formaldehyde resin11、多官能环氧树脂：polyfunctional epoxy resin12、溴化环氧树脂：brominated epoxy resin13、环氧酚醛：epoxy novolac14、氟树脂：fluroresin15、硅树脂：silicone resin16、硅烷：silane17、聚合物：polymer18、无定形聚合物：amorphous polymer19、结晶现象：crystalline polamer20、双晶现象：dimorphism21、共聚物：copolymer22、合成树脂：synthetic23、热固性树脂：thermosetting resin24、热塑性树脂：thermoplastic resin25、感光性树脂：photosensitive resin26、环氧当量：weight per epoxy equivalent (wpe)27、环氧值：epoxy value28、双氰胺：dicyandiamide29、粘结剂：binder30、胶粘剂：adesive31、固化剂：curing agent32、阻燃剂：flame retardant33、遮光剂：opaquer34、增塑剂：plasticizers35、不饱和聚酯：unsatuiated polyester36、聚酯薄膜：polyester37、聚酰亚胺薄膜：polyimide film (pi)38、聚四氟乙烯：polytetrafluoetylene (ptfe)39、聚全氟乙烯丙烯薄膜：perfluorinated ethylene-propylene copolymer film (fep)40、增强材料：reinforcing material41、玻璃纤维：glass fiber42、e玻璃纤维：e-glass fibre43、d玻璃纤维：d-glass fibre44、s玻璃纤维：s-glass fibre45、玻璃布：glass fabric46、非织布：non-woven fabric47、玻璃纤维垫：glass mats48、纱线：yarn 49、单丝：filament50、绞股：strand51、纬纱：weft yarn52、经纱：warp yarn53、但尼尔：denier54、经向：warp-wise55、纬向：weft-wise, filling-wise56、织物经纬密度：thread count57、织物组织：weave structure58、平纹组织：plain structure59、坏布：grey fabric60、稀松织物：woven scrim61、弓纬：bow of weave62、断经：end missing63、缺纬：mis-picks64、纬斜：bias65、折痕：crease66、云织：waviness67、鱼眼：fish eye68、毛圈长：feather length69、厚薄段：mark70、裂缝：split71、捻度：twist of yarn72、浸润剂含量：size content73、浸润剂残留量：size residue74、处理剂含量：finish level75、浸润剂：size76、偶联剂：couplint agent77、处理织物：finished fabric78、聚酰胺纤维：polyarmide fiber79、聚酯纤维非织布：non-woven polyester fabric80、浸渍绝缘纵纸：impregnating insulation paper81、聚芳酰胺纤维纸：aromatic polyamide paper82、断裂长：breaking length83、吸水高度：height of capillary rise84、湿强度保留率：wet strength retention85、白度：whitenness86、陶瓷：ceramics87、导电箔：conductive foil88、铜箔：copper foil89、电解铜箔：electrodeposited copper foil (ed copper foil)90、压延铜箔：rolled copper foil91、退火铜箔：annealed copper foil92、压延退火铜箔：rolled annealed copper foil (ra copper foil)93、薄铜箔：thin copper foil94、涂胶铜箔：adhesive coated foil95、涂胶脂铜箔：resin coated copper foil (rcc)96、复合金属箔：composite metallic material97、载体箔：carrier foil98、殷瓦：invar99、箔（剖面）轮廓：foil profile100、光面：shiny side101、粗糙面：matte side102、处理面：treated side103、防锈处理：stain proofing104、双面处理铜箔：double treated foil四、设计1、原理图：shematic diagram2、逻辑图：logic diagram3、印制线路布设：printed wire layout4、布设总图：master drawing5、可制造性设计：design-for-manufacturability6、计算机辅助设计：computer-aided design.(cad)7、计算机辅助制造：computer-aided manufacturing.(cam)8、计算机集成制造：computer integrat manufacturing.(cim)9、计算机辅助工程：computer-aided engineering.(cae)10、计算机辅助测试：computer-aided test.(cat)11、电子设计自动化：electric design automation .(eda)12、工程设计自动化：engineering design automaton .(eda2)13、组装设计自动化：assembly aided architectural design. (aaad)14、计算机辅助制图：computer aided drawing15、计算机控制显示：computer controlled display .(ccd)16、布局：placement17、布线：routing18、布图设计：layout19、重布：rerouting20、模拟：simulation21、逻辑模拟：logic simulation22、电路模拟：circit simulation23、时序模拟：timing simulation24、模块化：modularization25、布线完成率：layout effeciency26、机器描述格式：machine descripttionm format .(mdf)27、机器描述格式数据库：mdf databse28、设计数据库：design database29、设计原点：design origin30、优化（设计）：optimization (design)31、供设计优化坐标轴：predominant axis32、表格原点：table origin33、镜像：mirroring34、驱动文件：drive file35、中间文件：intermediate file36、制造文件：manufacturing documentation37、队列支撑数据库：queue support database38、元件安置：component positioning39、图形显示：graphics dispaly40、比例因子：scaling factor41、扫描填充：scan filling42、矩形填充：rectangle filling43、填充域：region filling44、实体设计：physical design45、逻辑设计：logic design46、逻辑电路：logic circuit47、层次设计：hierarchical design48、自顶向下设计：top-down design49、自底向上设计：bottom-up design50、线网：net51、数字化：digitzing52、设计规则检查：design rule checking53、走（布）线器：router (cad)54、网络表：net list55、计算机辅助电路分析：computer-aided circuit analysis56、子线网：subnet57、目标函数：objective function58、设计后处理：post design processing (pdp)59、交互式制图设计：interactive drawing design60、费用矩阵：cost metrix61、工程图：engineering drawing62、方块框图：block diagram63、迷宫：moze64、元件密度：component density65、巡回售货员问题：traveling salesman problem66、自由度：degrees freedom67、入度：out going degree68、出度：incoming degree69、曼哈顿距离：manhatton distance70、欧几里德距离：euclidean distance71、网络：network72、阵列：array73、段：segment74、逻辑：logic75、逻辑设计自动化：logic design automation76、分线：separated time77、分层：separated layer78、定顺序：definite sequence五、形状与尺寸：1、导线（通道）：conduction (track)2、导线（体）宽度：conductor width3、导线距离：conductor spacing4、导线层：conductor layer5、导线宽度/间距：conductor line/space6、第一导线层：conductor layer no.17、圆形盘：round pad8、方形盘：square pad9、菱形盘：diamond pad10、长方形焊盘：oblong pad11、子弹形盘：bullet pad12、泪滴盘：teardrop pad13、雪人盘：snowman pad14、v形盘：v-shaped pad15、环形盘：annular pad16、非圆形盘：non-circular pad17、隔离盘：isolation pad18、非功能连接盘：monfunctional pad19、偏置连接盘：offset land20、腹（背）裸盘：back-bard land21、盘址：anchoring spaur22、连接盘图形：land pattern23、连接盘网格阵列：land grid array24、孔环：annular ring25、元件孔：component hole26、安装孔：mounting hole27、支撑孔：supported hole28、非支撑孔：unsupported hole29、导通孔：via30、镀通孔：plated through hole (pth)31、余隙孔：access hole32、盲孔：blind via (hole)33、埋孔：buried via hole34、埋/盲孔：buried /blind via35、任意层内部导通孔：any layer inner via hole (alivh)36、全部钻孔：all drilled hole37、定位孔：toaling hole38、无连接盘孔：landless hole39、中间孔：interstitial hole40、无连接盘导通孔：landless via hole41、引导孔：pilot hole42、端接全隙孔：terminal clearomee hole43、准表面间镀覆孔：quasi-interfacing plated-through hole44、准尺寸孔：dimensioned hole45、在连接盘中导通孔：via-in-pad46、孔位：hole location47、孔密度：hole density48、孔图：hole pattern49、钻孔图：drill drawing50、装配图：assembly drawing51、印制板组装图：printed board assembly drawing52、参考基准：datum referance电路板术语总整理*****A*****Abietic Acid松脂酸.Abrasion Resistance耐磨性.Abrasives磨料,刷材.ABS树脂.Absorption吸收(入).Ac Impedance交流阻抗.Accelerated Test(Aging)加速老化(试验).Acceleration速化反应.Accelerator 加速剂,速化剂.Acceptability,Acceptance 允收性,允收.Access Hole露出孔,穿露孔.Accuracy准确度.Acid Number (Acid Value)酸值.Acoustic Microscope (AM)感音成像显微镜.Acrylic压克力(聚丙烯酸树脂).Actinic Light (or Intensity, or Radiation)有效光.Activation活化.Activator活化剂.Active Carbon活性炭.Active Parts(Devices)主动零件.Acutance解像锐利度.Addition Agent添加剂.Additive Process加成法.Adhesion附着力.Adhesion Promotor附着力促进剂.Adhesive胶类或接着剂.Admittance导纳(阻抗的倒数).Aerosol喷雾剂,气熔胶,气悬体.Aging老化.Air Inclusion气泡夹杂.Air Knife风刀.Algorithm算法.Aliphatic Solvent脂肪族溶剂.Aluminium Nitride(AlN)氮化铝.Ambient Tamp环境温度.Amorphous无定形,非晶形.Amp-Hour安培小时.Analog Circuit/Analog Signal模拟电路/模拟讯号. Anchoring Spurs着力爪.Angle of Contack接触角.Angle of Attack攻角.Anion阴离子.Anisotropic异向性,单向的.Anneal 韧化(退火).Annular Ring孔环.Anode阳极.Anode Sludge阳极泥.Anodizing阳极化.ANSI美国标准协会.Anti-Foaming Agent消泡剂.Anti-pit Agent抗凹剂.AOI自动光学检验.Apertures开口,钢版开口.AQL品质允收水准.AQL(Acceptable Quality Level)允收品质水准. Aramid Fiber聚醯胺纤维.Arc Resistance耐电弧性.Array排列.Artwork底片.ASIC特定用途绩体电路器.Aspect Ratio纵横比.Assembly组装装配.A-stage A阶段.ATE自动电测设备.Attenuation讯号衰减.Autoclave压力锅.Axial-lead轴心引脚.Azeotrope共沸混合液.*****B*****Back Light (Back Lighting)背光法.Back Taper反锥斜角.Backpanels, Backplanes支撑板.Back-up 垫板.Balanced Transmission Lines平衡式传输线.Ball Grid Array球脚数组(封装).Bandability弯曲性.Banking Agent护岸剂.Bare Chip Assembly裸体芯片组装.Barrel孔壁,滚镀.Base Material基材.Basic Grid基本方格.Batch批.Baume波美度(凡液体比重比水重则Be=145-(145÷Sp.Gr) 凡液体比重比水轻则Be=140÷(Sp.Gr-130)*Sp.Gr 为比重即同体绩物质对"纯水"1g/cm的比值). Beam lead光芒式的平行密集引脚.Bed-of-Nail Testing针床测试.Bellows Conact弹片式接触.Beta Ray Backscatter贝他射线反弹散射.Bevelling切斜边.Bias斜张纲布,斜纤法.Bi-Level Stencil]双阶式钢板.Binder粘结剂.Bits头(Drill Bits).Black Oxide黑氧化层.Blanking冲空断开.Bleack 漂洗.Bleeding溢流.Blind Via Hole肓通孔.Blister局部性分层或起泡.Block Diagram电路系统块图 .Blockout封纲.Blotting干印.Blotting Paper吸水纸.Blow Hole吹孔.Blue Plaque蓝纹(锡面钝化层).Blur Edge (Circle)模糊边带(圈). Bomb Sight弹标.Bond Strength结合强度. Bondability结合性.Bonding Layer结合层接着层. Bonding Sheet(Layer)接合片. Bonding Wire结合线.Bow, Bowing板弯.Braid编线.Brazing硬焊(用含银的铜锌合金焊条). 在425℃~870℃下进行熔接的方式). Break Point显像点.Break-away Panel可断开板. Breakdown Voltage崩溃电压. Break-out破出.Bridging搭桥.Bright Dip光泽浸渍处理. Brightener光泽剂.Brown Oxide棕氧化.Brush Plating刷镀.B-stageB阶段.Build Up Process增层法制程.Build-up堆积.Bulge鼓起.Bump 突块.Bumping Process凸块制程. Buoyancy浮力.Buried Via Hole埋导孔.Burn-in高温加速老化试验.Burning烧焦.Burr毛头.Bus Bar汇电杆.Butter Coat 外表树脂层.*****C*****C4 Chip JointC4芯片焊接.Cable电缆.CAD计算机辅助设计.Calendered Fabric轧平式纲布.Cap Lamination帽式压合法. Capacitance电容.Capacitive Coupling电容耦合. Capillary Action毛细作用.Carbide碳化物.Carbon Arc Lamp碳弧灯.Carbon Treatment, Active活化炭处理.Card卡板.Card Cages/Card Racks电路板构装箱.Carlson Pin卡氏定位稍.Carrier载体.Cartridge滤心.Castallation堡型绩体电路器.Catalyzed Board, Catalyzed Substrate催化板材. Catalyzing催化.Cathode阴极.Cation阴向离子, 阳离子.Caul Plate隔板.Cavitation空泡化半真空.Center-to-Center Spacing中心间距.Ceramics陶瓷.Cermet陶金粉.Certificate证明书.CFC氟氢碳化物.Chamfer倒角.Characteristic Impedance特性阻抗.Chase纲框.Check List检查清单.Chelate螯合.Chemical Milling化学研磨.Chemical Resistance抗化性.Chemisorption化学吸附.Chip芯片(粒).Chip Interconnection芯片互连.Chip on Board芯片粘着板.Chip On Glass晶玻接装(COG).Chisel钻针的尖部.Chlorinated Solvent含氯溶剂,氯化溶剂. Circumferential Separation环状断孔.Clad/Cladding披覆.Clean Room无尘室.Cleanliness清洁度.Clearance余地,余环.Clinched Lead Terminal紧箝式引脚.Clinched-wire Through Connection通孔弯线连接法 . Clip Terminal绕线端接.Coat, Coating皮膜表层.Coaxial Cable同轴缆线.Coefficient of Thermal Expansion热膨胀系数.Co-Firing共绕.Cold Flow冷流.Cold Solder Joint冷焊点.Collimated Light平行光.Colloid胶体.Columnar Structure柱状组织.Comb Pattern梳型电路.Complex Ion错离子.Component Hole零件孔.Component Orientation零件方向. Component Side组件面.Composites,(CEM-1,CEM-3)复合板材. Condensation Soldering凝热焊接,液化放热焊接. Conditioning整孔.Conductance导电.Conductive Salt导电盐.Conductivity导电度.Conductor Spacing导体间距.Conformal Coating贴护层.Conformity吻合性, 服贴性.Connector连接器.Contact Angle接触角.Contact Area接触区.Contact Resistance接触电阻.Continuity连通性.Contract Service协力厂,分包厂.Controlled Depth Drilling定深钻孔. Conversion Coating 转化皮膜.Coplanarity共面性.Copolymer共聚物.Copper Foil铜皮.Copper Mirror Test铜镜试验.Copper Paste铜膏.Copper-Invar-Copper (CIC)综合夹心板.Core Material内层板材,核材.Corner Crack 通孔断角.Corner Mark板角标记.Counterboring方型扩孔.Countersinking锥型扩孔.Coupling Agent 偶合剂.Coupon, Test Coupon板边试样.Coverlay/Covercoat表护层.Crack裂痕.Crazing白斑.Crease皱折.Creep潜变.Crossection Area截面积.Crosshatch Testing十字割痕试验. Crosshatching十字交叉区.Crosslinking, Crosslinkage交联,架桥. Crossover越交,搭交.Crosstalk噪声, 串讯.Crystalline Melting Point晶体熔点.C-Stage C阶段.Cure硬化,熟化.Current Density电流密度.Current-Carrying Capability载流能力.Curtain Coating濂涂法.*****D*****Daisy Chained Design菊瓣设计.Datum Reference基准参考.Daughter Board子板.Debris碎屑,残材.Deburring去毛头.Declination Angle斜射角.Definition边缘逼真度.Degradation 劣化.Degrasing脱脂.Deionized Water去离子水.Delamination分离.Dendritic Growth 枝状生长.Denier丹尼尔(是编织纺织所用各种纱类直径单位, 定义9000米纱束所具有的重量(以克米计)). Densitomer透光度计.Dent凹陷.Deposition 皮膜处理.Desiccator干燥器.Desmearing去胶渣.Desoldering解焊.Developer显像液,显像机.Developing显像 .Deviation偏差.Device电子组件.Dewetting缩锡.D-glassD玻璃.Diaze Film偶氮棕片.Dichromate重铬酸盐.Dicing芯片分割.Dicyandiamide(Dicy)双氰胺.Die 冲模.Die Attach晶粒安装.Die Bonding晶粒接着.Die Stamping冲压.Dielectric 介质.Dielectric Breakdown Voltage介质崩溃电压.Dielectric Constant介质常数.Dielectric Strength介质强度.Differential Scanning Calorimetry(DSC)微差扫瞄热卡分析法. Diffusion Layer扩散层.Digitizing数字化.Dihedral Angle双反斜角.Dimensional Stability尺度安定性.Diode二极管.Dip Coating浸涂法.Dip Soldering浸焊法.DIP(Dual Inline Package)双排脚封装体.Dipole偶极,双极.Direct / Indirect Stencil直接/间接版膜.Direct Emulsion直接乳胶.Direct Plating直接电镀.Discrete Compenent散装零件.Discrete Wiring Board散线电路板,复线板.Dish Down碟型下陷.Dispersant分散剂.Dissipation Factor散失因素.Disspation Factor散逸因子.Disturbed Joint受扰焊点.Doctor Blade修平刀,刮平刀.Dog Ear狗耳.Doping掺杂.Double Layer双电层.Double Treated Foil双面处理铜箔.Drag In / Drag Out带[进/带出.Drag Soldering拖焊.Drawbridging吊桥效应.Drift漂移.Drill Facet钻尖切削面.Drill Pointer钻针重磨机.Drilled Blank已钻孔的裸板.Dross浮渣.Drum Side铜箔光面.Dry Film干膜.Dual Wave Soldering 双波焊接.Ductility展性.Dummy Land假焊垫.Dummy, Dummying假镀(片).Durometer橡胶硬度计.DYCOstrate电浆蚀孔增层法.Dynamic Flex(FPC)动态软板.*****E*****E-Beam (Electron Beam)电子束.Eddy Current涡电流.Edge Spacing板边空地.Edge-Board Connector板边(金手指)承接器. Edge-Board Contact板边金手指.Edge-Dip Solderability Test板边焊锡性测试. EDTA乙二胺四乙酸.Effluent排放物.E-glass电子级玻璃.Elastomer弹性体.Electric Strength(耐)电性强度. Electrodeposition电镀.Electro-deposition Photoresist电着光阻, 电泳光阻. Electroforming电铸.Electroless-Deposition无电镀.Electrolytic Tough Pitch电解铜..Electrolytic-Cleaning电解清洗.Electro-migration电迁移.Electro-phoresis电泳动, 电渗.Electro-tinning镀锡.Electro-Winning电解冶炼.Elongation 延伸性, 延伸率.Embossing凸出性压花.EMF(Electromotive Force)电动势.EMI(Electromagnetic Interference)电磁干扰. Emulsion乳化.Emulsion Side药膜面.Encapsulating胶囊.Encroachment沾污,侵犯.End Tap封头.Entek有机护铜处理.Entrapment夹杂物.Entry Material盖板.Epoxy Resin环氧树脂.Etch Factor蚀刻因子.Etchant蚀刻剂(液).Etchback回蚀.Etching Indicator蚀刻指针.Etching Resist蚀刻阻剂.Eutetic Composition共融组成.Exotherm放热(曲线).Exposure曝光.Eyelet铆眼.*****F*****Fabric纲布.Face Bonding反面朝下结合.Failure故障.Fan Out Wiring/Fan In Wiring扇出布线/扇入布线. Farad 法拉.Farady法拉第.Fatigue Strength抗疲劳强度.Fault缺陷.Fault Plane断层面.Feed Through Hole导通孔.Feeder 进料器.Fiber Exposure玻纤显露.Fiducial Mark基准记号.Filament纤丝.Fill纬向.Filler填充料.Fillet内圆填角.Film底片.Film Adhesive接着膜,粘合膜.Filter过滤器.Fine Line细线.Fine Pitch密脚距,密线距,密垫距.Fineness粒度, 纯度.Finger手指.Finishing终修(饰).Finite Element Method有限要素分析法.First Article首产品.First Pass-Yield初检良品率.Fixture夹具.Flair刃角变形.Flame Point自燃点.Flame Resistant耐燃性.Flammability Rate燃性等级.Flare扇形崩口.Flash Plating闪镀.Flashover闪络.Flat Cable扁平排线.Flat Pack扁平封装(之零件).Flatness平坦度.Flexible Printed Circuit (FPC)软板.Flexural Failure挠曲损坏.Flexural Module弯曲模数, 抗挠性模数 . Flexural Strength抗挠强度.Flip Chip覆晶,扣晶.Flocculation絮凝.Flood Stroke Print覆墨冲程印刷.Flow Soldering (Wave Soldering)流焊. Fluorescence荧光.Flurocarbon Resin碳氟树脂.Flush Conductor嵌入式线路, 贴平式导体. Flush Point闪火点.Flute退屑槽.Flux助焊剂.Foil Burr铜箔毛边.Foil Lamination铜箔压板法.Foot残足(干膜残余物).Foot Print (Land Pattern)脚垫.Foreign Material 外来物,异物.Form-to-List布线说明清单.Four Point Twisting四点扭曲法.Free Radical自由基.Freeboard干舷.Frequency频率.Frit 玻璃熔料.Fully-Additive Process全加成法.Fungus Resistance抗霉性.Fused Coating熔锡层.Fusing熔合.Fusing Fluid助熔液.*****G*****G-10由连续玻纤所织成的玻纤布与环氧树脂粘结剂所复合成的材料.Gage, Gauge量规.Gallium Arsenide (GaAs)砷化镓.Galvanic Corrosion贾凡尼式腐蚀(电解式腐蚀). Galvanic Series贾凡尼次序(电动次序). Galvanizing镀锌.GAP第一面分离,长刃断开.Gate Array闸列,闸极数组.Gel Time胶化时间.Gelation Particle胶凝点.Gerber Data ,Gerber File格博档案(是美商Gerber公司专为PCB面线路图形与孔位,所发展一系列完整的软件档案).Ghost Image阴影.Gilding镀金(现为:Glod Plating).Glass Fiber玻纤.Glass Fiber Protrusion/Gouging, Groove玻纤突出/挖破.Glass Transition Temperature, Tg玻璃态转化温度.Glaze釉面,釉料.Glob Top圆顶封装体.Glouble Test球状测试法.Glycol (Ethylene Glycol)乙二醇.Golden Board测试用标准板.Grain Size结晶粒度.Grass Leak 大漏.Grid标准格.Ground Plane /Earth Plane接地层.Ground Plane Clearance接地空环.Guide Pin导针.Gull /Wing Lead鸥翼引脚.*****H*****Halation环晕.Half Angle半角.Halide卤化物.Haloing白圈,白边.Halon海龙,是CFC"氟碳化物"的一种商品名.Hard Anodizing硬阳极化.Hard Chrome Plating镀硬铬.Hard Soldering硬焊.Hardener (Curing Agent)硬化剂(或Curing Agent).Hardness硬度.Haring-Blum Cell海固槽.Harness电缆组合.Hay Wire跳线.Heat Cleaning烧洁.Heat Dissipation散热.Heat Distortion Point (Temp)热变形点(温度).Heat Sealing热封.Heat Sink Plane散热层.Heat Transfer Paste导热膏.Heatsink Tool散热工具.Hertz(Hz)赫.High Efficiency Particulate Air Filter (HEPA)高效空气尘粒过泸机. Hipot Test 高压电测.Hi-Rel高度靠度.Hit 击(钻孔时钻针每一次"刺下"的动作). Holding Time停置时间.Hole Breakout孔位破出.Hole Counter数孔机.Hole Density孔数密度.Hole Preparation通孔准备.Hole Pull Strength孔壁强度.Hole Void破洞.Hook 切削刀缘外凸.Hot Air Levelling喷锡.Hot Bar Soldering热把焊接.Hot Gas Soldering热风手焊.HTE(High Temperature Elongation)高温延伸性. Hull Cell哈氏槽.Hybrid Integrated Circuit混成电路. Hydraulic Bulge Test液压鼓起试验. Hydrogen Embrittlement氢脆.Hydrogen Overvoltage氢过(超)电压. Hydrolysis水解.Hydrophilic亲水性.Hygroscopic吸湿性.Hypersorption超吸咐.*****I*****I.C. Socket绩体电路器插座.Icicle锡尖.Illuminance照度.Image Transfer影像转移.Immersion Plating浸镀.Impedance阻抗.Impedance Match阻抗匹配.Impregnate含浸.In-Circuit Testing组装板电测.Inclusion异物,夹杂物.Indexing Hole基准孔.Inductance(L)电感.Infrared(IR)红外线.Input/Output输入/输出.Insert, Insertion插接.Inspection Overlay套检底片.Insulation Resistance绝缘电阻.Integrated Circuit(IC)绩体电路器.Inter Face接口.Interconnection互连.Intermetallic Compound (IMC)接口共化物.Internal Stress内应力.Interposer互边导电物.Interstitial Via-Hole(IVH)局部层间导通孔.Invar殷钢(63.8%Fe,36%Ni,0.2%C).Ion Cleanliness离子清洁度.Ion Exchange Resins离子交换树脂.Ion Migration离子迁移.Ionizable (Ionic) Contaimination离子性污染.Ionization游离,电离.Ionization Voltage (Corona Level)电离化电压(电缆内部狭缝空气中,引起其电离所施加之最小电压).IPC美国印刷电路板协会.Isolation隔离性,隔绝性.*****J*****JEDEC(Joint Electronic Device 联合电子组件工程委员会. Engineering Council)J-LeadJ型接脚.Job Shop专业工厂.Joule焦耳.Jumper Wire跳线.Junction接(合)面,接头.Just-In-Time(JIT)适时供应,及时出现.*****K*****Kapton聚亚醯胺软板.Karat克拉(1克拉(钻石)=0.2g 纯金则24k金为100%的钝金.Kauri-Butanol Value考立丁醇值(简称K.B.值).Kerf.切形,裁剪.Kevlar聚醯胺纤维.Key电键Key Board键盘.Kiss Pressure吻压, 低压.Knoop Hardness努普硬度.Known Good Die(KGD)已知之良好芯片.Kovar科伐合金(Fe53%,Ni29%,Co17%).Kraft Paper牛皮纸.*****L*****Lamda Wave延伸平波.Laminar Flow平流.Laminar Structure片状结构.Laminate Void板材空洞.Laminate(s)基板.Lamination Void压合空洞.Laminator压膜机.Land孔环焊垫,表面焊垫.Landless Hole无环通孔.Laser Direct Imaging (LDI)雷射直接成像.Laser Maching雷射加工法.Laser Photogenerator(LPG), Laser Photoplotter雷射曝光机. Laser Soldering雷射焊接法.Lay Back 刃角磨损.Lay Out布线,布局.Lay Up 叠合.Layer to Layer Spacing层间距离Leaching焊散漂出,熔出.Lead 引脚.Lead Frame脚架.Lead Pitch脚距.Leakage Current漏电电流.Legend文字标记.Leveling整平.Lifted Land孔环(焊垫)浮起.Ligand错离子附属体.Light Emitting Diodes (LED)发光二极管.Light Integrator光能累积器.Light Intensity光强度.Limiting Current Density极限电流密度.Liquid Crystal Display (LCD)液晶显示器.Liquid Dielectrics液态介质.Liquid Photoimagible Solder Mask, (LPSM)液态感光防焊绿漆. Local Area Network区域性网络.Logic 逻辑.Logic Circuit 逻辑电路.Loss Factor损失因素.Loss Tangent (TanδDK)损失正切.Lot Size批量.Luminance发光强度.Lyophilic亲水性胶体.*****M*****Macro-Throwing Power巨观分布力.Major Defect主要(严重)缺点.Major Weave Direction主要织向.Margin刃带(钻头尖部).Marking标记.Mask阻剂.Mass Finishing大量整面(拋光).Mass Lamination大型压板.Mass Transport质量输送.Master Drawing主图.Mat席(用于CEM-3(Composite Epoxy Material)的复合材料.)Matte Side毛面(电镀铜皮(ED Foil)之粗糙面).Mealing泡点.Mean Time To Failure (MTTF)故障前可用之平均时数. Measling白点.Mechanical Stretcher机械式张网机.Mechanical Warp机械式缠绕.Mechanism机理.Membrane Switch薄膜开关.Meniscograph Test弧面状沾锡试验.Meniscus弯月面.Mercury Vaper Lamp汞气灯.Mesh Count纲目数.Metal Halide Lamp 金属卤素灯.Metallization金属化.Metallized Fabric金属化纲布.Micelle微胞.Micro Wire Board微封线板.Micro-electronios微电子.Microetching微蚀.Microsectioning微切片法.Microstrip 微条.Microstrip Line微条线,微带线.Microthrowing Power微分布力.Microwave微波.Migration迁移.Migration Rate迁移率.Mil英丝.Minimum Annular Ring孔环下限.Minimum Electrical Spacing电性间距下限.Minor Weave Direction次要织向.Misregistration 对不准度.Mixed Componmt Mounting Technology混合零件之组装技术. Modem调变及解调器.Modification修改.Module模块.Modulus of Elasticity弹性系数.Moisture and Insulation Resistance Test湿气与绝缘电阻试验. Mold Release 脱模剂,离型剂.Mole摩尔.Monofilament单丝.Mother Board主机板,母板.Moulded Circuit模造立体电路机.Mounting Hole安装孔.Mounting Hole组装孔,机装孔.Mouse Bite鼠齿(蚀刻后线路边缘出现不规则缺口). Multi-Chip-Module(MCM)多芯片芯片模块. Multiwiring Board (or Discrete Wiring Board)复线板.*****N*****N.C.数值控制.Nail Head钉头.Near IR近红外线.Negative负片,钻尖的第一面外缘变窄.Negative Etch-back反回蚀.Negative Stencil负性感光膜.Negative-Acting Resist负性作用之阻剂.Network纲状元件.Newton牛顿.Newton Ring 牛顿环.Newtonian Liquid牛顿流体.Nick缺口.N-Methyl Pyrrolidine (NMP)N-甲基四氢哔咯.Noble Metal Paste贵金属印膏.Node节点.Nodule节瘤.Nomencleature标示文字符号.Nominal Cured Thickness标示厚度.Non-Circular Land非圆形孔环焊垫.Non-flammable非燃性.Non-wetting不沾锡.Normal Concentration (Strength)标准浓度,当量浓度. Normal Distribution常态分布.Novolac酯醛树脂.Nucleation , Nucleating核化.Numerical Control数值控制.Nylon尼龙.*****O*****Occlusion吸藏.Off-Contact架空.Offset第一面大小不均.OFHC(Oxyen Free High Conductivity)无氧高导电铜. Ohm欧姆.Oilcanning盖板弹动.OLB(Outer Lead Bond)外引脚结合.Oligomer寡聚物.Omega Meter离子污染检测仪.Omega Wave振荡波.On-Contact Printing密贴式印刷.Opaquer不透明剂,遮光剂.Open Circuits断线.Optical Comparater光学对比器(光学放大器.) Optical Density光密度.Optical Inspection光学检验.Optical Instrument光学仪器.Organic Solderability Preservatives (OSP)有机保焊剂. Osmosis渗透.Outgassing出气,吹气.Outgrowth悬出,横出,侧出.Output产出,输出.Overflow溢流.Overhang总悬空.Overlap 钻尖点分离.Overpotantial(Over voltage)过电位,过电压. Oxidation氧化.Oxygen Inhibitor氧化抑制剂.Ozone Depletion臭氧层耗损.*****P*****Packaging封装,构装.Pad焊垫,圆垫.Pad Master圆垫底片.Pads Only Board唯垫板.Palladium钯.Panel制程板.Panel Plating全板镀铜.Panel Process全板电镀法.Paper Phenolic纸质酚醛树脂(板材).Parting Agent脱膜剂.Passivation钝化,钝化外理.Passive Device (Component)被动组件(零件)Paste膏,糊.Pattern板面图形.Pattern Plating线路电镀.Pattern Process线路电镀法.Peak Voltage峰值电压.Peel Strength抗撕强度.Periodic Reverse (PR) Current周期性反电流. Peripheral周边附属设备.Permeability透气性,导磁率.Permittivity诱电率,透电率.。
PCB专业术语大汇集
PCBJargon(PCB专业术语) AAbsorption 吸收、吸入Accelerated Test（Aging）加速实验、加速老化Accelerator 加速剂、速化剂Accept/Acceptance 允收Acceptable Quality Level（AQL）允收品质水准Accuracy 准确度ACF：Adhesive copper foil 有胶铜箔Activator 活化剂、添加剂比称为ActivatorActive parts（Devices）主动零件，指积体电路或电晶体Addition Agent 添加剂Additive Process 加成法、分全加成、半加成及部份加成Adhesion 附著力Adhesive 胶类或接著剂Aging 老化Air Knife 风刀Ambient Temperature 环境温度Ampere 安培Amp-Hour 安培小时Annular Ring 孔环Anode 阳极Anode Bag 阳极带ANSI: American National Standard Institute 美国规范协会Anti-Forming Agent 消泡剂AOI: Automatic Optical Inspection 自动光学检验Aperture 开口APQP: Advanced Product Quality PlanArray 排列、阵列Artwork 底片ASIC: Application Specific Integrated Circuit 特定用途的积体电路器Aspect Ratio 纵横比、板厚与孔径之比值Assembly 装配、组装ATE: Automatic Testing Equipment 自动电测设备AVL: Approved Vender List 合格供应商BBack Light（Back Lighting）背光法Back-UP 垫板Backpanels/Backplanes 背板、支持板，厚度较厚，Ball Grid Array（BGA）球脚车列（封装）Barrel 孔壁Base Material 基材Batch 批（同时间发料某一数量的板子）Bevelling 切斜边Binder 黏结剂Black oxide 黑氧化层，另有棕氧化（Brown Oxide）Blind Via Hole 盲导孔Blister 局部性分层或起泡Blockout 封网，网板之空网处以水溶胶涂满Blow Hole 吹孔，PTH孔壁有破洞（void）所造成Boiler (Water Tube Boiler/ Fire Tube Boiler)BOM: Bill of Material 用料表Bond Strength 结合强度Bonding Sheet(Layer) 接合片、接著层，指PPBonding Wire 结合线，IC之晶片与PCB之引线Bow 板弯Break-away Panel 可断开板或者说Break Away TabBreak Point 出像点、影像点Break-Out 破出（钻孔破出开成断环情形）Bridging 搭桥、桥接Brightener 光泽剂Brush Plating 刷镀BTU/British Thermal Unit 英制热量单位Bump 突块Buried Via Hole 埋导孔Burn-in 高温加速老化实验Burning 烧焦Burr 毛头Buy-off 认可CCAD: Computer Aided Design 电脑辅助设计CAM: Computer Aided Manufacturing 电脑辅助制造CAT: Computer Aided Testing 电脑辅助测试Capacitance 电容Carbide 碳化物、碳化钨钻头CAR: Corrective Action Report 改善报告Carbon Treatment 活性碳处理Card 卡板Carrier 载体Cartridge 滤芯Cathode 阴极CCL: Copper Clad Laminates 铜箔基板Ceramics 陶瓷Certificate 证明书CFC 氟氯碳化物 Chloro-Fluoro-CarbonChamfer 倒角、去掉直角Characteristic Impedance 特性阻抗Cheek list 检察清单Chip 晶粒、晶片Chip On Board 晶片黏著板Clean Room 无尘室 (Class 100)Cleanliness 清洁度Clearance 余隙、余环COB（Chip on Board）晶片在板上直接组装COC（Certificate of Compliance）出货合格书COF（Chip on Flexible PCB）COG（Chip glass）Coefficient of Thermal Expansion 热膨胀系数（CTE）Cold Solder Joint 冷焊点Component Hole 零件孔Component Side 组件面、零件面Conditioning 整孔Conductivity 导电度Connector 连接器Continuity Test 连通性实验Copper Foil 铜箔、铜皮Copper Ball 铜球Corner Crack 镀通孔转角断角Cp: Capability of Process 制程能力指数Crack 裂痕Crazing 白斑（基板外观上的缺点）Crosstalk 杂讯、串讯Cure/Curing 硬化、热化Current Density （C.D.）电流密度（1 ASD=9.1 ASF）Curtain Coating 液涂法Datum 基准点Deburring 去毛头Defect 不良缺点Degreasing 脱脂Delamination 分层、爆板Dent 凹陷、缓和均匀的下陷Desmearing 除胶渣Developer 显像液Deviation 偏差Device 电子元件Dewetting 缩锡DFM: Design for Manufacturing/Dirty foreign Materials 异物、杂质Die 冲模Dielectric 介质Dielectric Constant 介质常数Dimensional Stability 尺度安定性DIP（Dual Inline Package）双排脚封装体Direct Plating 直接电镀DI Water 纯水 (De-Ionize Water)DOE/Design of Experiment 实验计划法DPPM（Defect Parts Per Million）Drilling 钻孔Drill Bit 钻针Dry Film 干膜Dummy 假镀EECN: Engineering Change Notice 工程变更通知Elongation 延伸性EMI 电磁干扰 Electromagnetic InterferenceENIG: Electroless Nickel Immersion Gold 化镍浸金Entek 有机护铜处理Entry Material 盖板E.T/Electric Test 电测、电气测试Epoxy Resin 环氧树脂ESD: Electro-Static Discharge 静电流量Etching 蚀刻Etchback 加蚀Etch Factor 蚀刻函数Etching Resist 抗蚀阻剂Expose Copper 漏铜Exposure 曝光Eyelet 铆钉 RivetFAAR（First Article Approval Report）Failure 故障、损坏Fault 缺陷、瑕疵FCC/Federal Communication Commission 美国联邦通讯委员会Fiber Exposure 玻织显露Fiducial Mark 基准记号、光学点Film 底片Filter 过滤器Fine Line 细线Finger 手指Finishing 制成品在外观上的最后处理First Article 试产的首件或首批小量产品First Pass-Yield 初检良品率Fixture 夹具、治具 (Rig and Fixture)Flame Resistant 耐燃性（分HB、VO、V1及V2等四级）Flux 助焊剂Foil Burr 铜箔毛边Foot Pint（Land Pattern）脚垫Foreign Material 外来物、异物FR4/Flame Resistant Laminates 耐燃性积层板材Frequency 频率GGauge 量规Gel Time 胶化时间Gerber Data/Gerber File 格搏档案Glass Fiber 玻璃纤维Glass Fiber Protrusion 玻纤突出Glass Transition Temperature/Tg 玻璃态转化温度Golden Board 测试用规范板Grid 规范格Ground Plane 接地层Guide Pin 导针HHaloing 白圈、白边（在钻孔、开槽等机械动作一旦过猛时将造成内部树脂之破碎或微小分层裂开的现象）Hardener 硬化剂Hardness 硬度Heat Dissipation 散热Hertz（Hz）赫芝HEPA/High Efficiency Particulate Air Filter 高效空气尘粒过滤机Hipot Test 高压电测 High Potential TestHit 擎Holding Time 停区时间Hole Block 孔塞Hole Breakout 孔位破出，简称BreakoutHole counter 数孔机Hole Density 孔数密度Hole Pull Strength 孔壁强度Hole Void 破洞Hot Air Levelling 喷锡 HASL/HALTHE(High Temperature Elongation) 高温延伸性II.C.Socket 积体电路插座Image Transfer 影像转移IMC: Inter-metallic compound 介面合金共化物Immersion Plating 浸镀Impedance 阻抗In-Circuit Testing 组装板电测，ICTIndexing Hole 基准孔Infrared(IR) 红外线Ink 油墨Inner Layer 内层Input/Output 输入、输出Insert/Insertion 插接、插装Insulation Resistance 绝缘电阻Integrated Circuit (IC) 积体电路器Interconnection互连Intermatallic Compound(IMC) 介面合金共化物Internal Stress 内应力Ion Cleanliness 离子清洁度Ionic Contamination 离子污染IPC: The Institute for Interconnecting and Packaging Electronic Circuits 美国印刷电路板协会ISO: International Organization for Standardization 国际规范组织Isolation 隔离性JJPCA/Japan Print Circuit Association 日本印刷电路工业会Just-In-Time(JIT) 适时供应KKeyboard 键盘Kraft Paper 牛皮纸LLaminate(s) 基板、积层板Laminator 压膜机Land 孔环焊垫、独立点Landless Hole 无环通孔Laser Direct Imaging/LDI 雷射直接成像Laser Photoplotter 雷射曝光机、绘图机Lay Out 布线、布局 (configuration, general arrangement) Lay Up 叠合Lead Frame 脚架Lead 引脚、接脚Legend 文字标记Levelling 整平Light Intensity 光强度LMW: License Manufacturing Warehouse 保税厂Lot Size 批量LRR(Lot Reject Rate)MMajor Defect 严重缺点、主要缺点Marking 标记Mask 阻剂Mass Lamination 大型压板MCM/Multi-Chip Module 多晶片模组Measling 白点Membrane Switch 薄膜开关Microctching 微蚀Microsectioning 微切片法Migration迁移Mil 英丝0.001 inmisregistration 对不准、对不准度MLB/Multi-Layer Board 多层板Modem 调变及解调器、数据机Modification 修改、改变Module 模组Mother Board 主机板NNail Head 钉头N.C.数值控制（Numerical Control）Negative 负片Negative etch-back 反回蚀Nick 缺口Node 节点Nodule 瘤Non-Conformance 不合格品Non-flammable 非燃性Non-wetting 不沾锡Normal Distribution 常态分配NPI：New project introduction)NRE Charge-Non-Recurring Engineering Charge 不会重收的工程费用OOhm 欧姆Omega Meter 离子污染检测仪Open Circuits 断线Optical Density 光密度Optical Inspection 光学检验Organic Solderability Preservatives(OSP) 有机保焊剂Outgassing 出气、吹气Output 产出、输出Overflow 溢流Oxidation氧化Ozone Depletion 臭氧层耗损PPackaging 封装、购装Packing 包装Pad 配圈、孔环焊垫Panel Plating 全板镀铜Passive Parts 被动零件，如电阻、电容Past 膏（锡膏Solder Paste）Pattern Plating 线路电镀PCB/Printed Circuit Board 印刷电路板Peel Strength 抗撕强度Peripheral 周边附属设备Phototool 底片（一般指偶氮棕片 Diazo Film）Pin Grid Array(PGA) 矩阵式针脚封装Pinhole 针孔Pin 接脚、插梢、插针Pink Ring 粉红圈Pits 凹点（小面积下陷）Pitch 脚距、垫距、线距Plasma 电浆Plated through Hole/PTH 镀通孔Plug 插脚、塞孔Polarization 分极、极化Polyimide(PI) 聚亚酸胺Popcorn Effect 爆M花效应Post Cure 疏孔度实验Power Plane 后续硬化、后烤Power Supply 电源层PPM/Parts Per Million 百万分之几Preheat 预热Prepreg 胶片、树脂片Press Plate 压合钢板Press-Fit Contact 挤入式接触Printing 印刷Probe 探针Profile 轮廓、部面图、升温曲线图积线Punch 横切、冲床QQIT(Quality improvement Team) 品质改善小组Qualified Products List 合格产品（供应者）名单RRadiometer 辐射计、光度计Radius 尺角、半径Reference Dimension 参考尺度、参考尺寸Reflow Soldering 重熔焊接、熔焊Registration 对准度Reject 剔退、拒收Reliability 可靠度、信赖度Repair 修理Resin Content 胶含量、树脂含量Resin Flow 胶流量、树脂流量Resist 阻剂、阻膜Resistor 电阻器、电阻Resolution 解像、解像度、解读度Resolving Power 解读力、解像力（分辨力）Rework(ing) 重工、再加工Ring 套环Roller Cutter 混切机（俗称锯板机）Roller Coating 滚动涂布法Routing 切外型、捞外型RRM: Revolutions per Minute 转速（每分钟）Run-out 偏转、绕转、累积距差SSCAR(Supplier CA Request) 供应商改善报告SCM: Supply chain Management 供应商经管系统Scratch 刮痕Screen Printing 网版印刷Scrubber 磨刷机、磨刷器Selective Plating 选择性电镀SEM/Scanning Electron Microscope 扫瞄式电子显微镜Semi-Conductor 半导体Shearing 剪、裁切Short 短路SIR(Surface Insulation Resistance) 表面绝缘电阻Side Wall 侧壁Sigma(Standard Deviation) 规范差Signal 讯号Silicon 矽Silk Screen 网版印刷、丝网印刷Skin Effect 集肤效应Skip Printing 漏印Slot 槽孔Smear 胶渣SMT/Surface Mount Technology 表面黏装技术Solder 焊锡Solderability 焊锡性Solder Ball 锡球Solder Bridging 锡桥Solder Bump 焊锡凸块Solder Dam 锡堤（IC脚间的防焊）Solder Levelling 喷锡、热风整平Solder Mask(S/M) 绿漆、防焊膜Solder Paste 锡膏Solder Plug 锡塞、锡柱Solder Pot 锡炉Solder Side 焊锡面Soldering Fluid/Soldering Oil 助焊液、护焊汕Solid Content 固体含量SOP(Standard Operation Procedure) 规范作业程序Spacing 间距SPC/Statistical Process Control 统计制程管制Specific Gravity SG比重Specification(Spec) 规范、规格Specimen 样品、试样Spindle 钻轴Spray Coating 喷著涂装Stencil 版膜、网版Storage condition 储存条件Stress Relief 消除应力Substrate 底材Surface Insulation Resistance(SIR) 表面绝缘电阻Surface Tenting 表面张力Surface-Mount Device 表面黏装零件Swelling Agents/Sweller 膨胀剂SWR(Special Working Request) 试产前之“特殊工作要求”TTab 接点、金手指Tape 撕胶带实验Teflon 铁氟龙Temperature Profile 温度曲线Template 模板Tensile Strength 抗拉强度Tenting 盖孔法Terminal 端子Thermal Stress 热应力Thermal Shock 热冲击Thin Copper Foil 薄铜箔Then film Technology 薄膜技术Throwing Power 分布力Tolerance 公差Touch Up 检修（简单的工具在手操作下即可进行的小规范的检修，称之Touch Up或Rewok 有些类似）Trace 线路、导线Traceability 追溯性、可溯性Transistor 电晶体Transmission Line 传输线Twist 板翘、板扭UUL 保险业实验 Underwriters Laboratories/INCUltra Violet Curing(UV Curing) 紫外线硬化Ultrasonic Cleaning 超音波清洗Undercut/Undercutting 侧蚀Universal Tester 万用型电测机VVacuum Lamination 真空压合Vacuum Packing 真空包装Viscosity 黏滞度、黏度Vision Systems 视觉系统Visual Examination(Inspection) 目视检查Voltage 电压WWafer 晶圆Warp/Warpage 板弯Warp and Twist 板弯翘Washer 垫圈Waste Treatment 废弃处理Water Absorption 吸水性Water Break 水膜破散、水破Watermark 水印Wave Soldering 波焊Weave Exposure 织纹显露Weave Texture 织纹隐现Welding 熔接Wet Process 湿式制程Wetting Balance 沾锡、沾湿White Spot 白点Wicking effect 灯芯效应Wire Bonding 打线结合WIP(Working Piece in Process) 在制品XX Axis X轴X-Ray X光YY-Axis Y轴Yield 良品率、良率、产率ZZ-Axis X轴OtherHDI-High Density inter-connect 高密度内连接SWOT Strengths Weaknesses Opportunities ThreatsCD: Compact DiscCPU: Central Process UnitLaser, YAG Laser)DLD: Direct Laser Drilling (CO2DVD: Digital Versatile DiscEEPROM: Electrically Erasable Programmable Read Only Memory EMS: Electronics Manufacturing ServiceGPS: Global Positioning ServiceHDD: Hard Disk DriveHDTV: High Density TVLCD: Liquid Crystal DisplayLED: Light Emitting DiodeVCD: Video Compact DiskQuality System Requirements QS-9000(質量體系要求)Advanced Product Quality Planning and Control Plan APQP(產品質量先期策劃和控制計劃)Measurement Systems Analysis MSA(測量系統分析)Potential Failure Mode and Effects Analysis FMEA(潜在失效模式與後果分析) Production Part Approval Process PPAP (生產件批准程序)Statistical Process Control SPC (統計過程控制)IPC-A-600Classification 分级Acceptance Criteria 允收规格Applicable Documents 参考资料Dimensions And Tolerances 尺度与公差Terms And Definitions 术语及定义Workmanship 工艺水准Externally Observable Characteristics 外观特性Board Edges 板边Burrs 看头、毛刺Nonmetallic Burrs 非金属性毛头Metallic Burrs 金属毛头Nicks 缺口Haloing 白边Base Material 基材Weave Exposure 织纹显露Weave Texture 织纹隐现Exposed/Disrupted Fibers 玻织曝露/扰乱Pits and Voids 凹点与凹坑Base Material Subsurface 基材次表面Measling白点Crazing白斑Delamination/Blister分层/起泡Foreign Inclusions外来夹杂物Solder Coatings and Fused Tin Lead喷锡板或熔锡板Nonwetting拒锡（不沾锡）Dewetting缩锡Holes-Plated-Through-General镀通孔概要Nodules/Burrs镀瘤/毛头Pink Ring粉红圈Voids-Copper Plating镀铜层破洞Voids-Finished Coating完工皮膜之镀层破洞Lifted Lands-(Visual)孔环浮离（目检）Holes-Unsupported未镀孔Haloing白圈Printed Contacts板边接触金手指Surface Plating-General表面镀层通则Surface Plating-Wire Bond Pads打线承垫之表面Burrs on Edge-Board Contacts板边接点之毛头Adhesion of Overplate表面镀层之附着力Marking标记Etched Marking蚀刻标记Screened or Ink Stamped Marking纲印或盖印之标记Solder Resist(Solder Mask)防焊绿漆Coverage Over Conductors (Skip Coverage)边线表面之覆盖性（覆盖不全、跳印）Registration to Holes (All Finishes)对孔之套准度（各种表处理层）Registration to Other Conductive Patterns其他防焊的对准性Ball Grid Array (Solder Resist-Defined Lands)球脚格列体之焊垫（绿漆设限之焊垫）Ball Grid Array (Copper-Defined Lands)球脚格列体（铜面设限之焊垫）Ball Grid Array (Solder Dam)球脚格列体（防焊堤）Blisters/Delamination起泡/分层Adhesion(Flaking or Peeling)附著力（破片或剥落）Waves/Wrinkles/Ripples起浪/起皱/纹路Tenting(Via Holes)盖孔（导通孔、过孔）Pattern Definition-Dimensional圆形尺度特性Conductor Width and Spacing线宽与间距Conductor Width线宽Conductor Spacing导线间距External Annular Ring-Measurement孔环测量External Annular Ring-Supported Holes有孔壁支援的外孔环External Annular Ring-Unsupported Holes无孔壁支援的外孔环Flatness平坦度Internally Observable Characteristics可观察到的内在特性Dielectric Materials介质材料Laminate Voids(Outside Thermal Zone)压板空洞（或热区之外）Registration/Conductors to Holes导体与通孔之间的对准度Clearance Hole/Unsupported/to Power/Ground Planes针对电源层或接地层具隔环之非镀通孔Delamination/Blister分层/起泡Etchback回蚀Negative Etchback反回蚀Smear Removal除胶渣Dielectric Material/Clearance/Metal Plane for Supported Holes 金属层与通孔壁之介质隔距Layer-to-Layer Spacing层与层之间距Resin Recession树脂缩陷Conductive Patterns-General导线概论Etching Characteristics蚀刻特性Print and Etch印后即蚀刻（指正片法）Surface Conductor Thickness(Foil Plus Plating)表导体厚度（铜箔加电镀铜）Foil Thickness-Internal Layers内层箔厚Plated-Through Holes-General镀通孔概论Annular Ring-Internal Layers各内层之孔环Lifted Lands-(Cross-Sections)焊环浮起（切片上所见）Foil Crack-(Internal Foil)“C”Crack内层铜箔之裂纹Foil Crack-(External Foil)镀层破裂Plating Crack-(Barrel)“E”Crack孔壁镀层破裂Plating Crack-(Corner)“F”Crack孔角镀层破裂Plating Nodules镀层长瘤Copper Plating Thickness-Hole Wall孔壁镀铜厚度Plating Voids镀层破洞Solder Coating Thickness (Only When Specified)焊锡皮膜厚度（当已规定检查者）Solder Resist Thickness绿漆厚度Wicking灯芯效应（指玻织束渗入化学铜）Wicking/Clearance Holes隔离孔之渗铜Innerlayer Separation-Vertical (Axial) Microsection内层（环）分离-垂直（纵断面）微切片Innerlayer Separation-Horizontal (Transverse) Microsection内层（环）分离-水平（横断面）微切片Material Fill of Blind and Buried Vias盲孔与埋孔之填充材料钻孔式镀通孔Plated-Through Holes-Drilled钻孔式镀通孔Burrs毛头Nailheading钉头Plated-Through Holes-Punched冲孔式镀通孔Roughness and Nodules粗糙与镀瘤Flare喇叭口Miscellaneous其他离顶Flexible And Rigid-Flex Printed Wiring软性及软硬合板Metal Core Printed Boards金属平心电路板Type Classifications型式分类Spacing Laminated Type间距压合板Insulation Thickness/Insulated Metal Substrate已绝缘金属底材之绝缘厚度Insulation Material Fill/Laminated Type Metal Core压合型金属平心之绝缘填料Cracks in Insulation Material Fill/Laminated Type压合型绝缘填充料之裂纹Core Bond to Plated-Through Hole Wall平心层与镀通孔之间的固著Flush Printed Boards表面全平板Flushness of Surface Conductor表面导线之平坦性Cleanliness Testing清洁度实验Solderability Testing焊锡性实验Plated-Through Holes镀通孔Electrical Integrity电性之完整。
PCB专业英语词汇
PCB专业英语词汇一．Process 工艺流程1．Board cut /开料2．Drill /钻孔3．IQC(Incoming Quality Control) /来料检查4．PTH(Plated Through Hole) /沉铜5．Panel Plating /整板电镀6．D/F(Dry Film) /干膜7．Pattern Plating /图形电镀8．ETCH /蚀刻9．QC (Quality Control) /品质检查10.W/F(Wet Film) /湿膜11.Legend /字符12.HAL(Hot Air Leveling) /喷锡13.Immersion gold (chemical gold) /沉金14.Routing /锣15.V-CUT /V刻16.Punting /啤17.Rinse /清洗18.FQC(Final Quality Control) /终检19.QA Audit /审核20.Package /包装21.Shipment /出货ship out二．The items For QA1.PQC(Process Quality Control) /过程品质检查2.IPQC(In Process Quality Control) /过程控制检查3.First Article check /首件检查4.Backlight /背光检查5.Microsection /切片检查6.Etch Factor /蚀刻系数7.Tape test /胶纸实验8.Lot check /批检9.Full check /全检10.Sampling check /抽检11.Customer /客户12.Date code /日期代码13.AQL level(Average Quality Level) /AQL水平14.Sample size /抽样数15.Lot size /批量数16.Visual check /目视检查17.Logo /商标18.Solder side /焊接面ponent side /元件面20.Gold tape test /金层结合力实验21.S/M tape test /绿油结合实验22.C/M tape test /字符结合实验23.Impedance test /阻抗测试24.Wetting test(solder ability test) /可焊性实验25.Specimen 样板，样品26.Outgoing Report(shipment report) 出货报告27.ACC(Accepted) 可接受28.Rej (Rejected) 拒收29.Pass 过30.UAI(Use As Is) 特采（让步接受）31.Defect 缺陷32.Corrective Actions 纠正措施33.MRB(Material Review Bcard) 物料审核委员会34.Customer Complain 客户投诉35.DCC(Document Control Center) 文控中心三．The items for Engineering Department1.Engineering Department工程部2.QE: Quality Engineering 品质工程师3.MI: Manufacturing Instruction生产指引4.ECN: Engineering Change notice 工程变更通知5.Template 模板6.E/T Fixture测试架7.Ground Layer地层8.Inner Layer内层9.Dummy Pad(inner layer)假PAD10.Artwork Check11.Pattern12.Pattern Artwork13.S/M Artwork14.Legend Artwork字符非林15.Carbon Artwork16.CAD: Computer Assistant Design17.CAM: Computer Assistant Manufacturing18.MI Audit19.Tolerance20.Second Drill21.Tenting22.certificate / 证书23.clear / 清除24.client / 客户25.samples 样板/样品四．Y ear or week and month1.week:星期2.Monday1:星期3.Tuesday4.Wednesday5.Thursday6.Friday7.Saturday8.Sunday/first day9.month:月10.January 1月11.February 2月12.March 3月13.April 4月14.May 5月15.June 6月16.July 7月17.August 8月18.September 9月19.October 10月20.November 11月21.December 12月五Other one glossary1. Guarantee 保证2. Calibration 刻度3. hole 孔，洞。
PCB之综合词汇
综合词汇：1、印制电路：printed circuit2、印制线路：printed wiring3、印制板：printed board4、印制板电路：printed circuit board (pcb)5、印制线路板：printed wiring board(pwb)6、印制元件：printed component7、印制接点：printed contact8、印制板装配：printed board assembly9、板：board10、单面印制板：single-sided printed board(ssb)11、双面印制板：double-sided printed board(dsb)12、多层印制板：mulitlayer printed board(mlb)13、多层印制电路板：mulitlayer printed circuit board14、多层印制线路板：mulitlayer prited wiring board15、刚性印制板：rigid printed board16、刚性单面印制板：rigid single-sided printed borad17、刚性双面印制板：rigid double-sided printed borad18、刚性多层印制板：rigid multilayer printed board19、挠性多层印制板：flexible multilayer printed board20、挠性印制板：flexible printed board21、挠性单面印制板：flexible single-sided printed board22、挠性双面印制板：flexible double-sided printed board23、挠性印制电路：flexible printed circuit (fpc)24、挠性印制线路：flexible printed wiring25、刚性印制板：flex-rigid printed board, rigid-flex printed board26、刚性双面印制板：flex-rigid double-sided printed board, rigid-flex double-sided printed27、刚性多层印制板：flex-rigid multilayer printed board, rigid-flex multilayer printed board28、齐平印制板：flush printed board29、金属芯印制板：metal core printed board30、金属基印制板：metal base printed board31、多重布线印制板：mulit-wiring printed board32、陶瓷印制板：ceramic substrate printed board33、导电胶印制板：electroconductive paste printed board34、模塑电路板：molded circuit board35、模压印制板：stamped printed wiring board36、顺序层压多层印制板：sequentially-laminated multilayer37、散线印制板：discrete wiring board38、微线印制板：micro wire board39、积层印制板：buile-up printed board40、积层多层印制板：build-up mulitlayer printed board (bum)41、积层挠印制板：build-up flexible printed board42、表面层合电路板：surface laminar circuit (slc)43、埋入凸块连印制板：b2it printed board44、多层膜基板：multi-layered film substrate(mfs)45、层间全内导通多层印制板：alivh multilayer printed board46、载芯片板：chip on board (cob)47、埋电阻板：buried resistance board48、母板：mother board49、子板：daughter board50、背板：backplane51、裸板：bare board52、键盘板夹心板：copper-invar-copper board53、动态挠性板：dynamic flex board54、静态挠性板：static flex board55、可断拼板：break-away planel56、电缆：cable57、挠性扁平电缆：flexible flat cable (ffc)58、薄膜开关：membrane switch59、混合电路：hybrid circuit60、厚膜：thick film61、厚膜电路：thick film circuit62、薄膜：thin film63、薄膜混合电路：thin film hybrid circuit64、互连：interconnection65、导线：conductor trace line66、齐平导线：flush conductor67、传输线：transmission line68、跨交：crossover69、板边插头：edge-board contact70、增强板：stiffener71、基底：substrate72、基板面：real estate73、导线面：conductor side74、元件面：component side75、焊接面：solder side76、印制：printing77、网格：grid78、图形：pattern79、导电图形：conductive pattern80、非导电图形：non-conductive pattern81、字符：legend82、标志：mark1、Access Hole 露出孔(穿露孔，露底孔) （FPC、软板相关术语）常指软板外表的保护层Coverlay(须先冲切出的穿露孔)，用以贴合在软板线路表面做为防焊膜的用途。
pcb专业词汇.doc
综合词汇1、印制电路：printed circuit2、印制线路：printed wiring3、印制板：printed board4、印制板电路：printed circuit board (pcb)5、印制线路板：printed wiring board(pwb)6、印制元件：printed component7、印制接点：printed contact8、印制板装配：printed board assembly9、板：board10、单面印制板：single-sided printed board(ssb)11、双面印制板：double-sided printed board(dsb)12、多层印制板：mulitlayer printed board(mlb)13、多层印制电路板：mulitlayer printed circuit board14、多层印制线路板：mulitlayer prited wiring board15、刚性印制板：rigid printed board16、刚性单面印制板：rigid single-sided printed borad17、刚性双面印制板：rigid double-sided printed borad18、刚性多层印制板：rigid multilayer printed board19、挠性多层印制板：flexible multilayer printed board20、挠性印制板：flexible printed board21、挠性单面印制板：flexible single-sided printed board22、挠性双面印制板：flexible double-sided printed board23、挠性印制电路：flexible printed circuit (fpc)24、挠性印制线路：flexible printed wiring25、刚性印制板：flex-rigid printed board, rigid-flex printed board26、刚性双面印制板：flex-rigid double-sided printed board, rigid-flex double-sided printed27、刚性多层印制板：flex-rigid multilayer printed board, rigid-flex multilayer printed board28、齐平印制板：flush printed board29、金属芯印制板：metal core printed board30、金属基印制板：metal base printed board31、多重布线印制板：mulit-wiring printed board32、陶瓷印制板：ceramic substrate printed board33、导电胶印制板：electroconductive paste printed board34、模塑电路板：molded circuit board35、模压印制板：stamped printed wiring board36、顺序层压多层印制板：sequentially-laminated mulitlayer37、散线印制板：discrete wiring board38、微线印制板：micro wire board39、积层印制板：buile-up printed board40、积层多层印制板：build-up mulitlayer printed board (bum)41、积层挠印制板：build-up flexible printed board42、表面层合电路板：surface laminar circuit (slc)43、埋入凸块连印制板：b2it printed board44、多层膜基板：multi-layered film substrate(mfs)45、层间全内导通多层印制板：alivh multilayer printed board46、载芯片板：chip on board (cob)47、埋电阻板：buried resistance board48、母板：mother board49、子板：daughter board50、背板：backplane51、裸板：bare board52、键盘板夹心板：copper-invar-copper board53、动态挠性板：dynamic flex board54、静态挠性板：static flex board55、可断拼板：break-away planel56、电缆：cable57、挠性扁平电缆：flexible flat cable (ffc)58、薄膜开关：membrane switch59、混合电路：hybrid circuit60、厚膜：thick film61、厚膜电路：thick film circuit62、薄膜：thin film63、薄膜混合电路：thin film hybrid circuit64、互连：interconnection65、导线：conductor trace line66、齐平导线：flush conductor67、传输线：transmission line68、跨交：crossover69、板边插头：edge-board contact70、增强板：stiffener71、基底：substrate72、基板面：real estate73、导线面：conductor side74、元件面：component side75、焊接面：solder side76、印制：printing77、网格：grid78、图形：pattern79、导电图形：conductive pattern80、非导电图形：non-conductive pattern81、字符：legend82、标志：mark基材：1、基材：base material2、层压板：laminate3、覆金属箔基材：metal-clad bade material4、覆铜箔层压板：copper-clad laminate (ccl)5、单面覆铜箔层压板：single-sided copper-clad laminate6、双面覆铜箔层压板：double-sided copper-clad laminate7、复合层压板：composite laminate8、薄层压板：thin laminate9、金属芯覆铜箔层压板：metal core copper-clad laminate10、金属基覆铜层压板：metal base copper-clad laminate11、挠性覆铜箔绝缘薄膜：flexible copper-clad dielectric film12、基体材料：basis material13、预浸材料：prepreg14、粘结片：bonding sheet15、预浸粘结片：preimpregnated bonding sheer16、环氧玻璃基板：epoxy glass substrate17、加成法用层压板：laminate for additive process18、预制内层覆箔板：mass lamination panel19、内层芯板：core material20、催化板材：catalyzed board ,coated catalyzed laminate21、涂胶催化层压板：adhesive-coated catalyzed laminate22、涂胶无催层压板：adhesive-coated uncatalyzed laminate23、粘结层：bonding layer24、粘结膜：film adhesive25、涂胶粘剂绝缘薄膜：adhesive coated dielectric film26、无支撑胶粘剂膜：unsupported adhesive film27、覆盖层：cover layer (cover lay)28、增强板材：stiffener material29、铜箔面：copper-clad surface30、去铜箔面：foil removal surface31、层压板面：unclad laminate surface32、基膜面：base film surface33、胶粘剂面：adhesive faec34、原始光洁面：plate finish35、粗面：matt finish36、纵向：length wise direction37、模向：cross wise direction38、剪切板：cut to size panel39、酚醛纸质覆铜箔板：phenolic cellulose paper copper-clad laminates(phenolic/paper ccl)40、环氧纸质覆铜箔板：epoxide cellulose paper copper-clad laminates (epoxy/paper ccl)41、环氧玻璃布基覆铜箔板：epoxide woven glass fabric copper-clad laminates42、环氧玻璃布纸复合覆铜箔板：epoxide cellulose paper core, glass cloth surfaces copper-clad laminates43、环氧玻璃布玻璃纤维复合覆铜箔板：epoxide non woven/woven glass reinforced copper-clad laminates44、聚酯玻璃布覆铜箔板：ployester woven glass fabric copper-clad laminates45、聚酰亚胺玻璃布覆铜箔板：polyimide woven glass fabric copper-clad laminates46、双马来酰亚胺三嗪环氧玻璃布覆铜箔板：bismaleimide/triazine/epoxide woven glass fabric copper-clad lamimates47、环氧合成纤维布覆铜箔板：epoxide synthetic fiber fabric copper-clad laminates48、聚四乙烯玻璃纤维覆铜箔板：teflon/fiber glass copper-clad laminates49、超薄型层压板：ultra thin laminate50、陶瓷基覆铜箔板：ceramics base copper-clad laminates51、紫外线阻挡型覆铜箔板：uv blocking copper-clad laminates基材的材料1、a阶树脂：a-stage resin2、b阶树脂：b-stage resin3、c阶树脂：c-stage resin4、环氧树脂：epoxy resin5、酚醛树脂：phenolic resin6、聚酯树脂：polyester resin7、聚酰亚胺树脂：polyimide resin8、双马来酰亚胺三嗪树脂：bismaleimide-triazine resin9、丙烯酸树脂：acrylic resin10、三聚氰胺甲醛树脂：melamine formaldehyde resin11、多官能环氧树脂：polyfunctional epoxy resin12、溴化环氧树脂：brominated epoxy resin13、环氧酚醛：epoxy novolac14、氟树脂：fluroresin15、硅树脂：silicone resin16、硅烷：silane17、聚合物：polymer18、无定形聚合物：amorphous polymer19、结晶现象：crystalline polamer20、双晶现象：dimorphism21、共聚物：copolymer22、合成树脂：synthetic23、热固性树脂：thermosetting resin24、热塑性树脂：thermoplastic resin25、感光性树脂：photosensitive resin26、环氧当量：weight per epoxy equivalent (wpe)27、环氧值：epoxy value28、双氰胺：dicyandiamide29、粘结剂：binder30、胶粘剂：adesive31、固化剂：curing agent32、阻燃剂：flame retardant33、遮光剂：opaquer34、增塑剂：plasticizers35、不饱和聚酯：unsatuiated polyester36、聚酯薄膜：polyester37、聚酰亚胺薄膜：polyimide film (pi)38、聚四氟乙烯：polytetrafluoetylene (ptfe)39、聚全氟乙烯丙烯薄膜：perfluorinated ethylene-propylene copolymer film (fep)40、增强材料：reinforcing material41、玻璃纤维：glass fiber42、e玻璃纤维：e-glass fibre43、d玻璃纤维：d-glass fibre44、s玻璃纤维：s-glass fibre45、玻璃布：glass fabric46、非织布：non-woven fabric47、玻璃纤维垫：glass mats48、纱线：yarn 49、单丝：filament50、绞股：strand51、纬纱：weft yarn52、经纱：warp yarn53、但尼尔：denier54、经向：warp-wise55、纬向：weft-wise, filling-wise56、织物经纬密度：thread count57、织物组织：weave structure58、平纹组织：plain structure59、坏布：grey fabric60、稀松织物：woven scrim61、弓纬：bow of weave62、断经：end missing63、缺纬：mis-picks64、纬斜：bias65、折痕：crease66、云织：waviness67、鱼眼：fish eye68、毛圈长：feather length69、厚薄段：mark70、裂缝：split71、捻度：twist of yarn72、浸润剂含量：size content73、浸润剂残留量：size residue74、处理剂含量：finish level75、浸润剂：size76、偶联剂：couplint agent77、处理织物：finished fabric78、聚酰胺纤维：polyarmide fiber79、聚酯纤维非织布：non-woven polyester fabric80、浸渍绝缘纵纸：impregnating insulation paper81、聚芳酰胺纤维纸：aromatic polyamide paper82、断裂长：breaking length83、吸水高度：height of capillary rise84、湿强度保留率：wet strength retention85、白度：whitenness86、陶瓷：ceramics87、导电箔：conductive foil88、铜箔：copper foil89、电解铜箔：electrodeposited copper foil (ed copper foil)90、压延铜箔：rolled copper foil91、退火铜箔：annealed copper foil92、压延退火铜箔：rolled annealed copper foil (ra copper foil)93、薄铜箔：thin copper foil94、涂胶铜箔：adhesive coated foil95、涂胶脂铜箔：resin coated copper foil (rcc)96、复合金属箔：composite metallic material97、载体箔：carrier foil98、殷瓦：invar99、箔（剖面）轮廓：foil profile100、光面：shiny side101、粗糙面：matte side102、处理面：treated side103、防锈处理：stain proofing104、双面处理铜箔：double treated foil设计1、原理图：shematic diagram2、逻辑图：logic diagram3、印制线路布设：printed wire layout4、布设总图：master drawing5、可制造性设计：design-for-manufacturability6、计算机辅助设计：computer-aided design.(cad)7、计算机辅助制造：computer-aided manufacturing.(cam)8、计算机集成制造：computer integrat manufacturing.(cim)9、计算机辅助工程：computer-aided engineering.(cae)10、计算机辅助测试：computer-aided test.(cat)11、电子设计自动化：electric design automation .(eda)12、工程设计自动化：engineering design automaton .(eda2)13、组装设计自动化：assembly aided architectural design. (aaad)14、计算机辅助制图：computer aided drawing15、计算机控制显示：computer controlled display .(ccd)16、布局：placement17、布线：routing18、布图设计：layout19、重布：rerouting20、模拟：simulation21、逻辑模拟：logic simulation22、电路模拟：circit simulation23、时序模拟：timing simulation24、模块化：modularization25、布线完成率：layout effeciency26、机器描述格式：machine descriptionm format .(mdf)27、机器描述格式数据库：mdf databse28、设计数据库：design database29、设计原点：design origin30、优化（设计）：optimization (design)31、供设计优化坐标轴：predominant axis32、表格原点：table origin33、镜像：mirroring34、驱动文件：drive file35、中间文件：intermediate file36、制造文件：manufacturing documentation37、队列支撑数据库：queue support database38、元件安置：component positioning39、图形显示：graphics dispaly40、比例因子：scaling factor41、扫描填充：scan filling42、矩形填充：rectangle filling43、填充域：region filling44、实体设计：physical design45、逻辑设计：logic design46、逻辑电路：logic circuit47、层次设计：hierarchical design48、自顶向下设计：top-down design49、自底向上设计：bottom-up design50、线网：net51、数字化：digitzing52、设计规则检查：design rule checking53、走（布）线器：router (cad)54、网络表：net list55、计算机辅助电路分析：computer-aided circuit analysis56、子线网：subnet57、目标函数：objective function58、设计后处理：post design processing (pdp)59、交互式制图设计：interactive drawing design60、费用矩阵：cost metrix61、工程图：engineering drawing62、方块框图：block diagram63、迷宫：moze64、元件密度：component density65、巡回售货员问题：traveling salesman problem66、自由度：degrees freedom67、入度：out going degree68、出度：incoming degree69、曼哈顿距离：manhatton distance70、欧几里德距离：euclidean distance71、网络：network72、阵列：array73、段：segment74、逻辑：logic75、逻辑设计自动化：logic design automation76、分线：separated time77、分层：separated layer78、定顺序：definite sequence形状与尺寸：1、导线（通道）：conduction (track)2、导线（体）宽度：conductor width3、导线距离：conductor spacing4、导线层：conductor layer5、导线宽度/间距：conductor line/space6、第一导线层：conductor layer no.17、圆形盘：round pad8、方形盘：square pad9、菱形盘：diamond pad10、长方形焊盘：oblong pad11、子弹形盘：bullet pad12、泪滴盘：teardrop pad13、雪人盘：snowman pad14、v形盘：v-shaped pad15、环形盘：annular pad16、非圆形盘：non-circular pad17、隔离盘：isolation pad18、非功能连接盘：monfunctional pad19、偏置连接盘：offset land20、腹（背）裸盘：back-bard land21、盘址：anchoring spaur22、连接盘图形：land pattern23、连接盘网格阵列：land grid array24、孔环：annular ring25、元件孔：component hole26、安装孔：mounting hole27、支撑孔：supported hole28、非支撑孔：unsupported hole29、导通孔：via30、镀通孔：plated through hole (pth)31、余隙孔：access hole32、盲孔：blind via (hole)33、埋孔：buried via hole34、埋/盲孔：buried /blind via35、任意层内部导通孔：any layer inner via hole (alivh)36、全部钻孔：all drilled hole37、定位孔：toaling hole38、无连接盘孔：landless hole39、中间孔：interstitial hole40、无连接盘导通孔：landless via hole41、引导孔：pilot hole42、端接全隙孔：terminal clearomee hole43、准表面间镀覆孔：quasi-interfacing plated-through hole44、准尺寸孔：dimensioned hole45、在连接盘中导通孔：via-in-pad46、孔位：hole location47、孔密度：hole density48、孔图：hole pattern49、钻孔图：drill drawing50、装配图：assembly drawing51、印制板组装图：printed board assembly drawing52、参考基准：datum referance*****A*****Abietic Acid松脂酸.Abrasion Resistance耐磨性.Abrasives磨料,刷材.ABS树脂.Absorption吸收(入).Ac Impedance交流阻抗.Accelerated Test(Aging)加速老化(试验).Acceleration速化反应.Accelerator 加速剂,速化剂.Acceptability,Acceptance 允收性,允收.Access Hole露出孔,穿露孔.Accuracy准确度.Acid Number (Acid V alue)酸值.Acoustic Microscope (AM)感音成像显微镜.Acrylic压克力(聚丙烯酸树脂).Actinic Light (or Intensity, or Radiation)有效光. Activation活化.Activator活化剂.Active Carbon活性炭.Active Parts(Devices)主动零件.Acutance解像锐利度.Addition Agent添加剂.Additive Process加成法.Adhesion附着力.Adhesion Promotor附着力促进剂.Adhesive胶类或接着剂.Admittance导纳(阻抗的倒数).Aerosol喷雾剂,气熔胶,气悬体.Aging老化.Air Inclusion气泡夹杂.Air Knife风刀.Algorithm算法.Aliphatic Solvent脂肪族溶剂.Aluminium Nitride(AlN)氮化铝.Ambient Tamp环境温度.Amorphous无定形,非晶形.Amp-Hour安培小时.Analog Circuit/Analog Signal模拟电路/模拟讯号. Anchoring Spurs着力爪.Angle of Contack接触角.Angle of Attack攻角.Anion阴离子.Anisotropic异向性,单向的.Anneal 韧化(退火).Annular Ring孔环.Anode阳极.Anode Sludge阳极泥.Anodizing阳极化.ANSI美国标准协会.Anti-Foaming Agent消泡剂.Anti-pit Agent抗凹剂.AOI自动光学检验.Apertures开口,钢版开口.AQL品质允收水准.AQL(Acceptable Quality Level)允收品质水准. Aramid Fiber聚醯胺纤维.Arc Resistance耐电弧性.Array排列.Artwork底片.ASIC特定用途绩体电路器.Aspect Ratio纵横比.Assembly组装装配.A-stage A阶段.ATE自动电测设备.Attenuation讯号衰减.Autoclave压力锅.Axial-lead轴心引脚.Azeotrope共沸混合液.*****B*****Back Light (Back Lighting)背光法.Back Taper反锥斜角.Backpanels, Backplanes支撑板.Back-up 垫板.Balanced Transmission Lines平衡式传输线.Ball Grid Array球脚数组(封装).Bandability弯曲性.Banking Agent护岸剂.Bare Chip Assembly裸体芯片组装.Barrel孔壁,滚镀.Base Material基材.Basic Grid基本方格.Batch批.Baume波美度(凡液体比重比水重则Be=145-(145÷Sp.Gr)Be=140÷(Sp.Gr-130)*Sp.Gr 为比重即同体绩物质对"纯水"1g/cm的比值). Beam lead光芒式的平行密集引脚.Bed-of-Nail Testing针床测试.Bellows Conact弹片式接触.Beta Ray Backscatter贝他射线反弹散射.Bevelling切斜边.Bias斜张纲布,斜纤法.Bi-Level Stencil]双阶式钢板.Binder粘结剂.Bits头(Drill Bits).Black Oxide黑氧化层.Blanking冲空断开.Bleack 漂洗.Bleeding溢流.Blind Via Hole肓通孔.Blister局部性分层或起泡.Block Diagram电路系统块图.Blockout封纲.Blotting干印.Blotting Paper吸水纸.Blow Hole吹孔.Blue Plaque蓝纹(锡面钝化层).Blur Edge (Circle)模糊边带(圈). Bomb Sight弹标.Bond Strength结合强度.Bondability结合性.Bonding Layer结合层接着层. Bonding Sheet(Layer)接合片. Bonding Wire结合线.Bow, Bowing板弯.Braid编线.Brazing硬焊(用含银的铜锌合金焊条). 425℃~870℃下进行熔接的方式). Break Point显像点.Break-away Panel可断开板. Breakdown Voltage崩溃电压.Break-out破出.Bridging搭桥.Bright Dip光泽浸渍处理. Brightener光泽剂.Brown Oxide棕氧化.Brush Plating刷镀.B-stageB阶段.Build Up Process增层法制程.Build-up堆积.Bulge鼓起.Bump 突块.Bumping Process凸块制程. Buoyancy浮力.Buried Via Hole埋导孔.Burn-in高温加速老化试验.Burning烧焦.Burr毛头.Bus Bar汇电杆.Butter Coat 外表树脂层.*****C*****C4 Chip JointC4芯片焊接.Cable电缆.CAD计算机辅助设计.Calendered Fabric轧平式纲布.Cap Lamination帽式压合法. Capacitance电容.Capacitive Coupling电容耦合.Capillary Action毛细作用.Carbide碳化物.Carbon Arc Lamp碳弧灯.Carbon Treatment, Active活化炭处理.Card卡板.Card Cages/Card Racks电路板构装箱.Carlson Pin卡氏定位稍.Carrier载体.Cartridge滤心.Castallation堡型绩体电路器.Catalyzed Board, Catalyzed Substrate催化板材. Catalyzing催化.Cathode阴极.Cation阴向离子, 阳离子.Caul Plate隔板.Cavitation空泡化半真空.Center-to-Center Spacing中心间距.Ceramics陶瓷.Cermet陶金粉.Certificate证明书.CFC氟氢碳化物.Chamfer倒角.Characteristic Impedance特性阻抗.Chase纲框.Check List检查清单.Chelate螯合.Chemical Milling化学研磨.Chemical Resistance抗化性.Chemisorption化学吸附.Chip芯片(粒).Chip Interconnection芯片互连.Chip on Board芯片粘着板.Chip On Glass晶玻接装(COG).Chisel钻针的尖部.Chlorinated Solvent含氯溶剂,氯化溶剂. Circumferential Separation环状断孔.Clad/Cladding披覆.Clean Room无尘室.Cleanliness清洁度.Clearance余地,余环.Clinched Lead Terminal紧箝式引脚.Clinched-wire Through Connection通孔弯线连接法. Clip Terminal绕线端接.Coat, Coating皮膜表层.Coaxial Cable同轴缆线.Coefficient of Thermal Expansion热膨胀系数. Co-Firing共绕.Cold Flow冷流.Cold Solder Joint冷焊点.Collimated Light平行光.Colloid胶体.Columnar Structure柱状组织.Comb Pattern梳型电路.Complex Ion错离子.Component Hole零件孔.Component Orientation零件方向.Component Side组件面.Composites,(CEM-1,CEM-3)复合板材. Condensation Soldering凝热焊接,液化放热焊接. Conditioning整孔.Conductance导电.Conductive Salt导电盐.Conductivity导电度.Conductor Spacing导体间距.Conformal Coating贴护层.Conformity吻合性, 服贴性.Connector连接器.Contact Angle接触角.Contact Area接触区.Contact Resistance接触电阻.Continuity连通性.Contract Service协力厂,分包厂.Controlled Depth Drilling定深钻孔. Conversion Coating 转化皮膜.Coplanarity共面性.Copolymer共聚物.Copper Foil铜皮.Copper Mirror Test铜镜试验.Copper Paste铜膏.Copper-Invar-Copper (CIC)综合夹心板.Core Material内层板材,核材.Corner Crack 通孔断角.Corner Mark板角标记.Counterboring方型扩孔.Countersinking锥型扩孔.Coupling Agent 偶合剂.Coupon, Test Coupon板边试样.Coverlay/Covercoat表护层.Crack裂痕.Crazing白斑.Crease皱折.Creep潜变.Crossection Area截面积.Crosshatch Testing十字割痕试验. Crosshatching十字交叉区.Crosslinking, Crosslinkage交联,架桥.Crossover越交,搭交.Crosstalk噪声, 串讯.Crystalline Melting Point晶体熔点.C-Stage C阶段.Cure硬化,熟化.Current Density电流密度.Current-Carrying Capability载流能力.Curtain Coating濂涂法.*****D*****Daisy Chained Design菊瓣设计.Datum Reference基准参考.Daughter Board子板.Debris碎屑,残材.Deburring去毛头.Declination Angle斜射角.Definition边缘逼真度.Degradation 劣化.Degrasing脱脂.Deionized Water去离子水.Delamination分离.Dendritic Growth 枝状生长.Denier丹尼尔(是编织纺织所用各种纱类直径单位, 9000米纱束所具有的重量(以克米计)). Densitomer透光度计.Dent凹陷.Deposition 皮膜处理.Desiccator干燥器.Desmearing去胶渣.Desoldering解焊.Developer显像液,显像机.Developing显像.Deviation偏差.Device电子组件.Dewetting缩锡.D-glassD玻璃.Diaze Film偶氮棕片.Dichromate重铬酸盐.Dicing芯片分割.Dicyandiamide(Dicy)双氰胺.Die 冲模.Die Attach晶粒安装.Die Bonding晶粒接着.Die Stamping冲压.Dielectric 介质.Dielectric Breakdown Voltage介质崩溃电压.Dielectric Constant介质常数.Dielectric Strength介质强度.Differential Scanning Calorimetry(DSC)微差扫瞄热卡分析法. Diffusion Layer扩散层.Digitizing数字化.Dihedral Angle双反斜角.Dimensional Stability尺度安定性.Diode二极管.Dip Coating浸涂法.Dip Soldering浸焊法.DIP(Dual Inline Package)双排脚封装体.Dipole偶极,双极.Direct / Indirect Stencil直接/间接版膜.Direct Emulsion直接乳胶.Direct Plating直接电镀.Discrete Compenent散装零件.Discrete Wiring Board散线电路板,复线板.Dish Down碟型下陷.Dispersant分散剂.Dissipation Factor散失因素.Disspation Factor散逸因子.Disturbed Joint受扰焊点.Doctor Blade修平刀,刮平刀.Dog Ear狗耳.Doping掺杂.Double Layer双电层.Double Treated Foil双面处理铜箔.Drag In / Drag Out带[进/带出.Drag Soldering拖焊.Drawbridging吊桥效应.Drift漂移.Drill Facet钻尖切削面.Drill Pointer钻针重磨机.Drilled Blank已钻孔的裸板.Dross浮渣.Drum Side铜箔光面.Dry Film干膜.Dual Wave Soldering 双波焊接.Ductility展性.Dummy Land假焊垫.Dummy, Dummying假镀(片).Durometer橡胶硬度计.DYCOstrate电浆蚀孔增层法.Dynamic Flex(FPC)动态软板.*****E*****E-Beam (Electron Beam)电子束.Eddy Current涡电流.Edge Spacing板边空地.Edge-Board Connector板边(金手指)承接器.Edge-Board Contact板边金手指.Edge-Dip Solderability Test板边焊锡性测试. EDTA乙二胺四乙酸.Effluent排放物.E-glass电子级玻璃.Elastomer弹性体.Electric Strength(耐)电性强度. Electrodeposition电镀.Electro-deposition Photoresist电着光阻, 电泳光阻. Electroforming电铸.Electroless-Deposition无电镀.Electrolytic Tough Pitch电解铜..Electrolytic-Cleaning电解清洗.Electro-migration电迁移.Electro-phoresis电泳动, 电渗.Electro-tinning镀锡.Electro-Winning电解冶炼.Elongation 延伸性, 延伸率.Embossing凸出性压花.EMF(Electromotive Force)电动势.EMI(Electromagnetic Interference)电磁干扰. Emulsion乳化.Emulsion Side药膜面.Encapsulating胶囊.Encroachment沾污,侵犯.End Tap封头.Entek有机护铜处理.Entrapment夹杂物.Entry Material盖板.Epoxy Resin环氧树脂.Etch Factor蚀刻因子.Etchant蚀刻剂(液).Etchback回蚀.Etching Indicator蚀刻指针.Etching Resist蚀刻阻剂.Eutetic Composition共融组成.Exotherm放热(曲线).Exposure曝光.Eyelet铆眼.*****F*****Fabric纲布.Face Bonding反面朝下结合.Failure故障.Fan Out Wiring/Fan In Wiring扇出布线/扇入布线. Farad 法拉.Farady法拉第.Fatigue Strength抗疲劳强度.Fault缺陷.Fault Plane断层面.Feed Through Hole导通孔.Feeder 进料器.Fiber Exposure玻纤显露.Fiducial Mark基准记号.Filament纤丝.Fill纬向.Filler填充料.Fillet内圆填角.Film底片.Film Adhesive接着膜,粘合膜.Filter过滤器.Fine Line细线.Fine Pitch密脚距,密线距,密垫距.Fineness粒度, 纯度.Finger手指.Finishing终修(饰).Finite Element Method有限要素分析法.First Article首产品.First Pass-Yield初检良品率.Fixture夹具.Flair刃角变形.Flame Point自燃点.Flame Resistant耐燃性.Flammability Rate燃性等级.Flare扇形崩口.Flash Plating闪镀.Flashover闪络.Flat Cable扁平排线.Flat Pack扁平封装(之零件).Flatness平坦度.Flexible Printed Circuit (FPC)软板.Flexural Failure挠曲损坏.Flexural Module弯曲模数, 抗挠性模数. Flexural Strength抗挠强度.Flip Chip覆晶,扣晶.Flocculation絮凝.Flood Stroke Print覆墨冲程印刷.Flow Soldering (Wave Soldering)流焊. Fluorescence荧光.Flurocarbon Resin碳氟树脂.Flush Conductor嵌入式线路, 贴平式导体. Flush Point闪火点.Flute退屑槽.Flux助焊剂.Foil Burr铜箔毛边.Foil Lamination铜箔压板法.Foot残足(干膜残余物).Foot Print (Land Pattern)脚垫.Foreign Material 外来物,异物.Form-to-List布线说明清单.Four Point Twisting四点扭曲法.Free Radical自由基.Freeboard干舷.Frequency频率.Frit 玻璃熔料.Fully-Additive Process全加成法.Fungus Resistance抗霉性.Fused Coating熔锡层.Fusing熔合.Fusing Fluid助熔液.*****G*****G-10由连续玻纤所织成的玻纤布与.Gage, Gauge量规.Gallium Arsenide (GaAs)砷化镓.Galvanic Corrosion贾凡尼式腐蚀(电解式腐蚀). Galvanic Series贾凡尼次序(电动次序). Galvanizing镀锌.GAP第一面分离,长刃断开.Gate Array闸列,闸极数组.Gel Time胶化时间.Gelation Particle胶凝点.Gerber Data ,Gerber File格博档案(是美商Gerber公司专为PCB面线路,所发展一系列完整的软件档案).Ghost Image阴影.Gilding镀金(现为:Glod Plating).Glass Fiber玻纤.Glass Fiber Protrusion/Gouging, Groove玻纤突出/挖破.Glass Transition Temperature, Tg玻璃态转化温度.Glaze釉面,釉料.Glob Top圆顶封装体.Glouble Test球状测试法.Glycol (Ethylene Glycol)乙二醇.Golden Board测试用标准板.Grain Size结晶粒度.Grass Leak 大漏.Grid标准格.Ground Plane /Earth Plane接地层.Ground Plane Clearance接地空环.Guide Pin导针.Gull /Wing Lead鸥翼引脚.*****H*****Halation环晕.Half Angle半角.Halide卤化物.Haloing白圈,白边.Halon海龙,是CFC"氟碳化物"的一种商品名.Hard Anodizing硬阳极化.Hard Chrome Plating镀硬铬.Hard Soldering硬焊.Hardener (Curing Agent)硬化剂(或Curing Agent).Hardness硬度.Haring-Blum Cell海固槽.Harness电缆组合.Hay Wire跳线.Heat Cleaning烧洁.Heat Dissipation散热.Heat Distortion Point (Temp)热变形点(温度).Heat Sealing热封.Heat Sink Plane散热层.Heat Transfer Paste导热膏.Heatsink Tool散热工具.Hertz(Hz)赫.High Efficiency Particulate Air Filter (HEPA)高效空气尘粒过泸机. Hipot Test 高压电测.Hi-Rel高度靠度.Hit 击(钻孔时钻针每一次"刺下"的动作).Holding Time停置时间.Hole Breakout孔位破出.Hole Counter数孔机.Hole Density孔数密度.Hole Preparation通孔准备.Hole Pull Strength孔壁强度.Hole Void破洞.Hook 切削刀缘外凸.Hot Air Levelling喷锡.Hot Bar Soldering热把焊接.Hot Gas Soldering热风手焊.HTE(High Temperature Elongation)高温延伸性.Hull Cell哈氏槽.Hybrid Integrated Circuit混成电路.Hydraulic Bulge Test液压鼓起试验.Hydrogen Embrittlement氢脆.Hydrogen Overvoltage氢过(超)电压.Hydrolysis水解.Hydrophilic亲水性.Hygroscopic吸湿性.Hypersorption超吸咐.*****I*****I.C. Socket绩体电路器插座.Icicle锡尖.Illuminance照度.Image Transfer影像转移.Immersion Plating浸镀.Impedance阻抗.Impedance Match阻抗匹配.Impregnate含浸.In-Circuit Testing组装板电测.Inclusion异物,夹杂物.Indexing Hole基准孔.Inductance(L)电感.Infrared(IR)红外线.Input/Output输入/输出.Insert, Insertion插接.Inspection Overlay套检底片.Insulation Resistance绝缘电阻.Integrated Circuit(IC)绩体电路器.Inter Face接口.Interconnection互连.Intermetallic Compound (IMC)接口共化物.Internal Stress内应力.Interposer互边导电物.Interstitial Via-Hole(IVH)局部层间导通孔.Invar殷钢(63.8%Fe,36%Ni,0.2%C).Ion Cleanliness离子清洁度.Ion Exchange Resins离子交换树脂.Ion Migration离子迁移.Ionizable (Ionic) Contaimination离子性污染.Ionization游离,电离.Ionization Voltage (Corona Level)电离化电压(电缆内部狭缝空气中,引起其).IPC美国印刷电路板协会.Isolation隔离性,隔绝性.*****J*****JEDEC(Joint Electronic Device 联合电子组件工程委员会.Engineering Council)J-LeadJ型接脚.Job Shop专业工厂.Joule焦耳.Jumper Wire跳线.Junction接(合)面,接头.Just-In-Time(JIT)适时供应,及时出现.*****K*****Kapton聚亚醯胺软板.Karat克拉(1克拉(钻石)=0.2g 纯金则24k金为100%的钝金.Kauri-Butanol Value考立丁醇值(简称K.B.值).Kerf.切形,裁剪.Kevlar聚醯胺纤维.Key电键Key Board键盘.Kiss Pressure吻压, 低压.Knoop Hardness努普硬度.Known Good Die(KGD)已知之良好芯片.Kovar科伐合金(Fe53%,Ni29%,Co17%).Kraft Paper牛皮纸.*****L*****Lamda Wave延伸平波.Laminar Flow平流.Laminar Structure片状结构.Laminate Void板材空洞.Laminate(s)基板.Lamination V oid压合空洞.Laminator压膜机.Land孔环焊垫,表面焊垫.Landless Hole无环通孔.Laser Direct Imaging (LDI)雷射直接成像.Laser Maching雷射加工法.Laser Photogenerator(LPG), Laser Photoplotter雷射曝光机. Laser Soldering雷射焊接法.Lay Back 刃角磨损.Lay Out布线,布局.Lay Up 叠合.Layer to Layer Spacing层间距离Leaching焊散漂出,熔出.Lead 引脚.Lead Frame脚架.Lead Pitch脚距.Leakage Current漏电电流.Legend文字标记.Leveling整平.Lifted Land孔环(焊垫)浮起.Ligand错离子附属体.Light Emitting Diodes (LED)发光二极管.Light Integrator光能累积器.Light Intensity光强度.Limiting Current Density极限电流密度.Liquid Crystal Display (LCD)液晶显示器.Liquid Dielectrics液态介质.Liquid Photoimagible Solder Mask, (LPSM)液态感光防焊绿漆. Local Area Network区域性网络.Logic 逻辑.Logic Circuit 逻辑电路.Loss Factor损失因素.Loss Tangent (TanδDK)损失正切.Lot Size批量.Luminance发光强度.Lyophilic亲水性胶体.*****M*****Macro-Throwing Power巨观分布力.Major Defect主要(严重)缺点.Major Weave Direction主要织向.Margin刃带(钻头尖部).Marking标记.Mask阻剂.Mass Finishing大量整面(拋光).Mass Lamination大型压板.Mass Transport质量输送.Master Drawing主图.Mat席(用于CEM-3(Composite Epoxy Material)的.)Matte Side毛面(电镀铜皮(ED Foil)之粗糙面).Mealing泡点.Mean Time To Failure (MTTF)故障前可用之平均时数. Measling白点.Mechanical Stretcher机械式张网机.Mechanical Warp机械式缠绕.Mechanism机理.Membrane Switch薄膜开关.Meniscograph Test弧面状沾锡试验.Meniscus弯月面.Mercury Vaper Lamp汞气灯.Mesh Count纲目数.Metal Halide Lamp 金属卤素灯.Metallization金属化.Metallized Fabric金属化纲布.Micelle微胞.Micro Wire Board微封线板.Micro-electronios微电子.Microetching微蚀.Microsectioning微切片法.Microstrip 微条.Microstrip Line微条线,微带线.Microthrowing Power微分布力.Microwave微波.Migration迁移.Migration Rate迁移率.Mil英丝.Minimum Annular Ring孔环下限.Minimum Electrical Spacing电性间距下限.Minor Weave Direction次要织向.Misregistration 对不准度.Mixed Componmt Mounting Technology混合零件之组装技术. Modem调变及解调器.Modification修改.Module模块.Modulus of Elasticity弹性系数.Moisture and Insulation Resistance Test湿气与绝缘电阻试验. Mold Release 脱模剂,离型剂.Mole摩尔.Monofilament单丝.Mother Board主机板,母板.Moulded Circuit模造立体电路机.Mounting Hole安装孔.Mounting Hole组装孔,机装孔.Mouse Bite鼠齿(蚀刻后线路边缘出现不规则缺口).Multi-Chip-Module(MCM)多芯片芯片模块.Multiwiring Board (or Discrete Wiring Board)复线板.*****N*****N.C.数值控制.Nail Head钉头.Near IR近红外线.Negative负片,钻尖的第一面外缘变窄.Negative Etch-back反回蚀.Negative Stencil负性感光膜.Negative-Acting Resist负性作用之阻剂.Network纲状元件.Newton牛顿.Newton Ring 牛顿环.Newtonian Liquid牛顿流体.Nick缺口.N-Methyl Pyrrolidine (NMP)N-甲基四氢哔咯.Noble Metal Paste贵金属印膏.Node节点.Nodule节瘤.Nomencleature标示文字符号.Nominal Cured Thickness标示厚度.Non-Circular Land非圆形孔环焊垫.Non-flammable非燃性.Non-wetting不沾锡.Normal Concentration (Strength)标准浓度,当量浓度. Normal Distribution常态分布.Novolac酯醛树脂.Nucleation , Nucleating核化.Numerical Control数值控制.Nylon尼龙.*****O*****Occlusion吸藏.Off-Contact架空.Offset第一面大小不均.OFHC(Oxyen Free High Conductivity)无氧高导电铜.Ohm欧姆.Oilcanning盖板弹动.OLB(Outer Lead Bond)外引脚结合.Oligomer寡聚物.Omega Meter离子污染检测仪.Omega Wave振荡波.On-Contact Printing密贴式印刷.Opaquer不透明剂,遮光剂.Open Circuits断线.Optical Comparater光学对比器(光学放大器.) Optical Density光密度.Optical Inspection光学检验.Optical Instrument光学仪器.Organic Solderability Preservatives (OSP)有机保焊剂. Osmosis渗透.Outgassing出气,吹气.Outgrowth悬出,横出,侧出.Output产出,输出.Overflow溢流.Overhang总悬空.Overlap 钻尖点分离.Overpotantial(Over voltage)过电位,过电压. Oxidation氧化.Oxygen Inhibitor氧化抑制剂.Ozone Depletion臭氧层耗损.*****P*****Packaging封装,构装.Pad焊垫,圆垫.Pad Master圆垫底片.Pads Only Board唯垫板.Palladium钯.Panel制程板.Panel Plating全板镀铜.Panel Process全板电镀法.Paper Phenolic纸质酚醛树脂(板材).Parting Agent脱膜剂.Passivation钝化,钝化外理.Passive Device (Component)被动组件(零件)Paste膏,糊.Pattern板面图形.Pattern Plating线路电镀.Pattern Process线路电镀法.Peak Voltage峰值电压.Peel Strength抗撕强度.。
PCB专业词汇
PCB专业词汇PCB，即印刷电路板（Printed Circuit Board），是现代电子设备中不可缺少的一部分。
PCB由电气连接、信号传输、导线分布、电源供应等多个重要元件组成，为电子产品提供了可靠的基础支持。
在PCB工程设计和生产过程中，涉及到众多的专业词汇和术语，下面是一些常见的PCB专业词汇。
1. 线路(Trace) ：在电路板上绘制的导线，是电路板中最基本的元件。
2. 焊盘(Pad) ：电子元件连接至电路板上的部分，用于与焊料连接，以确保良好连接和固定。
3. 电路板层(PCB Layer) ：电路板的不同层，用于提供电路连接的支持和连接4. 焊接(Soldering) ：把焊料涂于焊盘上，使焊盘与电子元件连接，从而实现电路连接和固定。
5. 接地(Ground) ：电路板上用来消除干扰和防止静电等问题的虚接线，是一条“安全阀”。
6. 电源(Power) ：为PCB提供能量，使电子元件能够正常运行的部分。
7. 线路宽度(Trace Width) ：绘制线路的宽度，它是电路板设计和制造中的一个重要参数。
8. 间距(Spacing) ：PCB上电子元件之间的距离，影响电路板的紧凑程度和稳定性。
9. 材料(Materials) ：作为电路板构建和制造的基础材料，包括玻璃纤维、铜等常用材料。
10. 涂覆(Solder Mask) ：在PCB表面施加涂料，以保护电子元件和追踪线免受外部环境的影响以及缩短信号传输时间。
11. 丝印(Silk Screen) ：以文字或图形形式在PCB表面打印标记和标识的一种方法。
12. 经孔(Via) ：在电路板层之间进行电气联通的洞孔。
13. 环形电缆(Annular Ring) ：表示设备，尤其在PCB外围情况下元件的焊盘和电气测量的间距。
14. 层压板（Lamination) ：PCB层被压合为一个完整的电路板。
15. SMT (Surface mount technology)：一种电子元件表面焊接技术，大大提高了电子产品的制造效率和质量。
PCB专业用语总集
PCB专业用语总集PCB是电子元件中不可缺少的一部分，其成本以及技术水平会直接影响整个电子产品的设计与性能。
在PCB制作过程中，设计者和工程师需要使用大量的专业术语来描述不同的元件、线路和板子。
为方便大家了解和学习，下面总结一下PCB专业用语总集。
一、PCB的种类1.单面板(single-sided PCB)：指PCB上只有单一一面可以使用的电路板。
在其中一侧通过印刷工艺将零部件和线路印刷上去。
2.双面板(double-sided PCB)：指PCB上两侧都可以安装电路的电路板。
通过普通的电镀工艺交叉衔接。
3.多层板(multi-layer PCB)：指PCB板综合多块印刷电路板通过压合形成的，一般是至少三层或以上，并且每一层的线路采用一套相互分离的电路。
4.高层板（high-density interconnect PCB，HDI PCB）：指对内部零部件的高度和，导线间距，形状，尺寸等具有很高的要求的PCB板。
5.刚性板(rigid PCB)：指采用硬材质作为基材，在固定的工艺生产出的PCB板，整个PCB板体的形态和力学性能都比较稳定。
6.软性板（flexible PCB）：采用薄膜作为基材，一般还增加了零部件的连接和金属覆盖层，可以在弯曲时不破裂，且具有弯曲阈值的PCB板。
7.刚柔板（rigid-flex PCB）：刚性板和柔性板的优点都吸取并形成的一种新型电路板。
二、PCB设计相关专业术语1.电子元件（electrical component）：指所有电路板上的基础元件，例如电阻，电容，二极管和晶体管等。
2.焊盘（pad）：连接电子元件与线路的金属表面。
3.钻孔（drill hole）：钻入PCB板的孔用于在不同层之间穿线。
4.连线（trace）：连接元器件和焊盘的电线。
5.自动布线（auto-routing）：由电脑自动选取连接点并完成连线。
6.过孔（VIA）：由一个孔如穿透层层导线的网络。
PCB词专业术语
专业术语I.药品原材料ABS树脂Accelerator速化剂Acrylic压克力Activator活化剂Additives添加剂Active carbon 活性碳Adhesive胶类,接着剂Aresol喷雾剂Aluminum Nitride氮化铝Aliphatic Solvent脂肪族溶剂Anode Sludge阳极泥Anti-foaming agent.消泡剂Anti-pit agent抗凹剂Banking agent 护岸剂Binder 粘结剂Brightener 光泽剂Carbide 碳化物Abrasives 刷材Pumice slurry 浮石粉Ceramics 陶瓷Cermet 陶金粉Chelator 鳌合剂Colliod 胶体Coupling Agent 耦合剂Developer 显影液Dross 浮渣Entrapment 夹杂物Epoxy resin 环氧树脂Etchant 蚀刻液ｅPTFE 扩张型聚四氟乙烯富强材Filament 织丝Filler 填充料Fillet 填锡Flux 助焊剂Fusing fluid 助溶液Graphite石墨Halide 卤化物Halon 海龙Solder mask 防焊剂Mold release脱模剂OSP 有机保焊剂Plladium钯Parting agent脱膜剂Phonitiator感光创始剂Saponifier 皂化剂Sequestering agent 鳌合剂Silicon 硅Silk screen 丝网Silk paste 银膏Sludge 沉淀物Sweller 膨松剂Slurry 淤泥Teflon 铁氟龙Wetting agent 湿润剂Dispersant 分散剂Curing agent 硬化剂Formaldehyde 甲醛Accelerator速化剂Neutralizer中和剂Palladium钯Hydrochloric acid 盐酸Sulfuric Acid 硫酸Air knife 气刀Back up 垫板Bar code 条形码Bare board 空板Base material 基材Bits 针尖,头Card 卡板Cartridge 滤芯Copper foil 铜箔Copper paste 铜膏Core 核心板Coverlayer 保护层Debris 碎屑Diazo Film 偶氮棕片Die 冲模Dry film 干膜Entry board 盖板Fixture 夹具Flute 退屑槽Flying lead 飞脚Foot print 脚垫Foreign material 外来物,异物Glaze 釉面,釉料Lead frame 脚架Module 模块Mother board 母板Monofilament 单丝Multifilament 复丝Nail Head 钉头Pad 焊垫Press plate 钢板Probe 探针Pressure foot 压力脚Rack 挂架Reinforcement 辅强物,辅强材Squeege刮刀Stencil 版膜Stiffener 辅强板Template 模板Core Material 内曾板层Doctor Blade 修平刀,刮平刀Flute 退屑槽Guide Pin 导针Laminate 基板Laminator 压膜机Sand blast 喷沙V oid 空洞Prepreg树脂片各制程Inner Layer 内层Cutting 裁切Beveling 磨边Punching 冲孔Lamination 压合Brown oxidization 棕化Routing 捞边Panel plating 全板镀铜Curing 硬化Coating 濂涂法Degreasing 脱脂Desmearing 除胶渣Deburing 去毛头HASL喷锡Electrolytic plating :电镀E-less plating 化学镀Electrolytic Cleaning 电解清洗Neutralizing中和Conditioner 清洁整孔Water Rinse 水洗Microetching 微蚀Pre-activation 预浸Activation 活化Acceleration 速化ENIG化镍浸金Entek抗氧化Etchback 回蚀DES Developing Etching StrippingExposure 曝光Rework 重工SMT 表面贴装技术Polymerization 聚合反应Pre-treatment 前处理Post-treatment 后处理。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
PCB行业专业词汇大全—马建整理* Process Module 說明:A. 下料( Cut Lamination)a-1 裁板( Sheets Cutting)a-2 原物料發料(Panel)(Shear material to Size)B. 鑽孔(Drilling)b-1 內鑽(Inner Layer Drilling )b-2 一次孔(Outer Layer Drilling )b-3 二次孔(2nd Drilling)b-4 雷射鑽孔(Laser Drilling )(Laser Ablation )b-5 盲(埋)孔鑽孔(Blind & Buried Hole Drilling)C. 乾膜製程( Photo Process(D/F))c-1 前處理(Pretreatment)c-2 壓膜(Dry Film Lamination)c-3 曝光(Exposure)c-4 顯影(Developing)c-5 蝕銅(Etching)c-6 去膜(Stripping)c-7 初檢( Touch-up)c-8 化學前處理,化學研磨( Chemical Milling )c-9 選擇性浸金壓膜(Selective Gold Dry Film Lamination)c-10 顯影(Developing )c-11 去膜(Stripping )D. 壓合Laminationd-1 黑化(Black Oxide Treatment)d-2 微蝕(Microetching) d-3 鉚釘組合(eyelet )d-4 疊板(Lay up)d-5 壓合(Lamination)d-6 後處理(Post Treatment)d-7 黑氧化( Black Oxide Removal )d-8 銑靶(spot face)d-9 去溢膠(resin flush removal)E. 減銅(Copper Reduction)e-1 薄化銅(Copper Reduction)F. 電鍍(Horizontal Electrolytic Plating)f-1 水平電鍍(Horizontal Electro-Plating) (Panel Plating) f-2 錫鉛電鍍( Tin-Lead Plating ) (Pattern Plating)f-3 低於1 mil ( Less than 1 mil Thickness )f-4 高於1 mil ( More than 1 mil Thickness)f-5 砂帶研磨(Belt Sanding)f-6 剝錫鉛( Tin-Lead Stripping)f-7 微切片( Microsection)G. 塞孔(Plug Hole)g-1 印刷( Ink Print )g-2 預烤(Precure)g-3 表面刷磨(Scrub)g-4 後烘烤(Postcure)H. 防焊(綠漆): (Solder Mask)h-1 C面印刷(Printing Top Side)h-2 S面印刷(Printing Bottom Side)h-3 靜電噴塗(Spray Coating)h-4 前處理(Pretreatment)h-5 預烤(Precure)h-6 曝光(Exposure)h-7 顯影(Develop)h-8 後烘烤(Postcure)h-9 UV烘烤(UV Cure)h-10 文字印刷( Printing of Legend )h-11 噴砂( Pumice)(Wet Blasting)h-12 印可剝離防焊(Peelable Solder Mask)I . 鍍金Gold platingi-1 金手指鍍鎳金( Gold Finger )i-2 電鍍軟金(Soft Ni/Au Plating)i-3 浸鎳金( Immersion Ni/Au) (Electroless Ni/Au)J. 噴錫(Hot Air Solder Leveling)j-1 水平噴錫(Horizontal Hot Air Solder Leveling)j-2 垂直噴錫( Vertical Hot Air Solder Leveling)j-3 超級焊錫(Super Solder )j-4. 印焊錫突點(Solder Bump)K. 成型(Profile)(Form)k-1 撈型(N/C Routing ) (Milling)k-2 模具沖(Punch)k-3 板面清洗烘烤(Cleaning & Backing)k-4 V型槽( V-Cut)(V-Scoring)k-5 金手指斜邊( Beveling of G/F)L. 短斷路測試(Electrical Testing) (Continuity & Insulation Testing)l-1 AOI 光學檢查( AOI Inspection)l-2 VRS 目檢(Verified & Repaired)l-3 汎用型治具測試(Universal Tester)l-4 專用治具測試(Dedicated Tester)l-5 飛針測試(Flying Probe)M. 終檢( Final Visual Inspection)m-1 壓板翹( Warpage Remove)m-2 X-OUT 印刷(X-Out Marking)m-3 包裝及出貨(Packing & shipping)m-4 目檢( Visual Inspection)m-5 清洗及烘烤( Final Clean & Baking)m-6 護銅劑(ENTEK Cu-106A)(OSP)m-7 離子殘餘量測試(Ionic Contamination Test )(Cleanliness Test)m-8 冷熱衝擊試驗(Thermal cycling Testing)m-9 焊錫性試驗( Solderability Testing )N. 雷射鑽孔(Laser Ablation)N-1 雷射鑽Tooling孔(Laser ablation Tooling Hole)N-2 雷射曝光對位孔(Laser Ablation Registration Hole)N-3 雷射Mask製作(Laser Mask)N-4 雷射鑽孔(Laser Ablation)N-5 AOI 檢查及VRS ( AOI Inspection & Verified & Repaired)N-6 Blaser AOI (after Desmear and Microetching)N-7 除膠渣(Desmear)N-8 微蝕(Microetching )A/W (artwork) 底片Ablation 燒溶(laser),切除abrade 粗化abrasion resistance 耐磨性absorption 吸收ACC ( accept ) 允收accelerated corrosion test 加速腐蝕accelerated test 加速試驗acceleration 速化反應accelerator 加速劑acceptable 允收activator 活化液active work in process 實際在製品adhesion 附著力adhesive method 黏著法air inclusion 氣泡air knife 風刀amorphous change 不定形的改變amount 總量amylnitrite 硝基戊烷analyzer 分析儀anneal 回火annular ring 環狀墊圈;孔環anode slime (sludge) 陽極泥anodizing 陽極處理AOI ( automatic optical inspection ) 自動光學檢測applicable documents 引用之文件AQL sampling 允收水準抽樣aqueous photoresist 液態光阻aspect ratio 縱橫比(厚寬比) As received 到貨時back lighting 背光back-up 墊板banked work in process 預留在製品base material 基材baseline performance 基準績效batch 批beta backscattering 貝他射線照射法beveling 切斜邊;斜邊biaxial deformation 二方向之變形black-oxide 黑化blank controller 空白對照組blank panel 空板blanking 挖空blip 彈開blister 氣泡;起泡blistering 氣泡blow hole 吹孔board-thickness error 板厚錯誤bonding plies 黏結層bow ; bowing 板彎break out 從平環內破出bridging 搭橋;橋接BTO (Build To Order) 接單生產burning 燒焦burr 毛邊(毛頭) camcorder 一體型攝錄放機carbide 碳化物carlson pin 定位梢carrier 載運劑catalyzing 催化catholic sputtering 陰極濺射法caul plate 隔板;鋼板calibration system requirements 校驗系統之各種要求center beam method 中心光束法central projection 集中式投射線certification 認證chamfer 倒角(金手指) chamfering 切斜邊;倒角characteristic impedance 特性阻抗charge transfer overpotential 電量傳遞過電壓chase 網框checkboard 棋盤chelator 蟹和劑chemical bond 化學鍵chemical vapor deposition 化學蒸著鍍circumferential void 圓周性之孔破clad metal 包夾金屬clean room 無塵室clearance 間隙coat 鍍外表coating error 防焊覆蓋錯誤coefficient of thermal expansion (CTE) 熱澎脹系數cold solder joint 冷焊點cold-weld 金屬粉末冷焊color 顏色color error 顏色錯誤compensation 補償competitive performance 競爭力績效complex salt 錯化物complexor 錯化物component hole 零件孔component side 零件面concentric 同心conformance 密貼性consumer products 消費性產品contact resistance 接觸電阻continuous performance 連續發揮效能contract service 協力廠controlled split 均裂式conventional flow 亂流方式conventional tensile test 傳統張力測試法conversion coating 轉化層convex 突出coordinate list 資料清單copper claded laminates (CCL) 銅箔基板copper exposure 線路露銅copper mirror 鏡銅copper pad 銅箔圓配copper residue (copper splash) 銅渣corrosion rate numbering 腐蝕速率計數系統corrosion resistance 抗蝕性coulombs law 庫倫定律countersink 喇叭孔coupon 試樣coupon location 試樣點covering power 遮蓋力CPU 中央處理器crack 破裂;裂痕crazing 裂痕;白斑cross linking 交聯聚合cross talk 呼應作用crosslinking 交聯crystal collection 結晶收集curing 聚合體current efficiency 電流效率cut-outs 挖空cutting 裁板cyanide 氰化物cycles of learning 學習循環cycle-time reduction 交期縮短date code 週期deburring 去毛頭dedicated 專用型degradation 退變delamination 分層dent / pin hole 凹陷/ 針孔department of defense 國防部designation 字碼簡示法de-smear 除膠渣developing 顯影dewetting 縮錫dewetting time 縮錫時間dimension error 外形尺寸錯誤dielectric constant 介質常數difficulty 困難度difunctional 雙功能dimension 尺寸dimension stability 尺寸安定性dimensional stability 尺度安定性dimension and tolerance 尺寸與公差dirty hole 孔內異物discolor hole 孔黑;孔灰;氧化discoloration 變色disposable eyelet method 消耗性鉚釘法distortion factor 尺寸變形函數double side 雙面板downtime 停機時間drill 鑽孔drill bit 鑽頭drill facet 鑽尖切萷面drill pointer 鑽尖重(研)磨機drilled blank board 已鑽孔之裸板drilling 鑽孔dry film 乾膜ductility 延展性economy of scale 經濟規模edge spacing 板邊空地edge-board contact ( gold finger ) 金手指efficiency 能量效率electric test 電測electrical testing 電測;測試electrochemical machine ECM 電化學加工法electrochemical reactor 電化學反應器electroforming 電鑄electroless plate 化學銅electroless-deposition 無電鍍electropolishing 電解拋光electrorefining 電解精鍊electrowinning 電解萃取elliptical set 橢圓形embrittlement 脆性entitlement performance 可達成績效entrapment 電鍍夾雜物epoxy 環氧樹酯equipotential 電位線error data file 異常情形etch rate 蝕銅速率etchants 蝕刻液etchback 回蝕evaluation program 評估用程式exposure 曝光external pin method 外部插梢法eyelet hole 鉚釘孔Eyeletting 鉚眼fabric 網布failure 故障fast response 快速回應fault 瑕庛;缺陷fiber exposure 纖維顯露fiber protrusion 纖維突出fiducial mark 光學點,基準記號filler 填充料film 底片filtration 過濾finished board 成品fixing 固著fixture 電測夾具(治具) flaking off 粹離flammability rating 燃性等級flare 喇叭形孔flat cable 併排電纜feedback loop 回饋循環first-in-first-out (FIFO) 先進先出flexible manufacturing system (FMS) 彈性製造系統flux 助焊劑foil distortion 銅層變形fold 空泡foreign include 異物foreign material 基材內異物free radical chain polymerization 自由基連鎖聚合fully additive 加成法fully annealed type 徹底回火軔化之類形function 函數fundamental and basic 基本fungus resistance 抗黴性funnel flange 喇叭形摺翼galvanized 加法尼化製程gap 鑽尖分開gauge length 有效長度gel time 膠化時間general resist ink 一般阻劑油墨general 通論general industrial 一般性(電子)工業級geometrical levelling 幾何平整glass transition temperature (Tg) 玻璃態轉換溫度Gold 金gold finger 金手指gold plating 鍍金golden board 標準板gouges 刷磨凹溝gouging 挖破grain boundary 金屬晶體之四邊green 綠色grip 夾頭ground plane 接地層ground plane clearance 接地空環hackers 駭客HAL ( hot air leveling ) 噴錫haloing 白邊;白圈hardener 硬化劑hardness 硬度hepa filter 空氣濾清器high performance industrial 高性能(電子)工業級high reliability 高可靠度high resolution 高解析度high temperature elongation (HTE) 高溫延展性銅箔high temperature epoxy (HTE) 高溫樹酯hit 擊hole counter 數孔機hole diameter 孔徑hole diameter error 孔徑錯誤hole location 孔位hole number 孔數hole wall quality 孔壁品質hook 外弧hot dip 熱浸法hull cell 哈氏槽hybrid 混成積體電路hydrogen bonding 氫鍵hydrolysis 水解hydrometallurgy 濕法冶金法image analysis system 影像分析系統image transfer 影像轉移immersion gold 浸金(化鎳金) immersion plating 浸鍍法impedance 阻抗infrared reflow 紅外線重熔inhibitor 熱聚合抑制劑injection mold 射模ink 油墨innerlayer & outlayer 內外層insulation resistance 絕緣電阻intended position 應該在的位置intensifier 增強器intensity 強度inter molecular exchange 交互改變interconnection 互相連通ionic contaminants 離子性污染物ionic contamination testing 離子污染試驗IPA 異丙醇inspiration (啟蒙) identification 確認計劃目標implementation 改善方案information 數據internalization 制度化invisible inventory 無形的庫存knife edges 刀緣Knoop 努普(硬度單位) kraft paper 牛皮紙laminar flow 層流laminate 基層板laminating 壓合lamination 壓合laminator 壓膜機land 焊墊lay back 刃角磨損lay up 組合疊板layout 佈線;佈局lead screw 牽引螺絲leakage 漏電learning curve 學習曲線legend 文字標記leveling 平整levelling additive 平整劑levelling power 平整力life support 維繫生命limiting current 極限電流line space 線距line width 線寬linear variable differential transformer(LVDL) 線性可變差動轉換器liquid 液狀(態) liquid crystal resins 液晶樹脂liquid photoimageable solder resist ink 液態感光防焊油墨liquid photoresist ink 液態光阻劑油墨lot size 批量lower carrier 底部承載板mechanical plating 機祴鍍法machine scrub 刷磨清潔法macrothrowing power 巨分佈力margin 鑽頭刃帶market share 市場佔有率marking error 文字錯誤masked leveling 儰裝平整mass lamination 大型壓板mass transfer 質量傳送效應mass transfer overpotential 質量傳遞過電壓mass transportation 質傳master drawing 主圖;藍圖material use factor 材料使用率mealing 泡點;白點memory 記憶裝置meniscograph solderability measurement 新月型焊錫效果microetch 微蝕microetching 微蝕microfocus 微焦距microfocus system 微焦距系統microprofile 微表面microsectioning 微切片法microthrowing power 微分佈力migration 遷移mini-tensile tester 迷你拉力測試儀mis hole location 孔位錯誤misregistration 焊錫面與零件面對位偏差misregsitration 對不準moisture and insulation resistance test 濕氣與絕緣電阻試驗molded circuit board (MCB) 模製電路板monoethanal amine 單乙醇氨monohydrate state 水化物monomer 單分子膜;單體mouse bite 鋸齒;蝕刻缺口msec 毫秒muffle furnace 高溫焚火爐multichip 超大IC型(多晶片模組) mylar 保護膜nail head 釘頭NC drill 數位鑽孔機negative etchback 反回蝕negative film 負片negative rake angle 負摳耙角network 迴路;網路neutralization 中和nick 缺口nickel 鎳nodule 銅瘤;瘤粒no flow resin 不流樹脂noise 雜訊nominal 標示nominal dimension 標定長度nominal gel time 標示膠性時間nominal resin content 標示膠含量nominal resin flow 標示膠流量nominal scaled flow thickness 標示比例流量厚度OA equip 辦公室自動化設備obsolescence factor 報廢因素OEM 原設備製造商offset-list 補償數據清單ohmmeter 歐姆計open 斷路open circuits 斷路open short testing 斷短路測試opening 開口original art work (A/W) 原稿底片Others 其它outgrowth 增出over design 牛刀殺雞overlap 鑽尖重疊overlay entry 蓋板overpotential 過電壓oxidation 氧化oxide treatment 黑化處理oxided cytochrome 氧化性之細包色素oxygen evolution 氧氣發生反應packed bed 充填床式pad 錫墊;圓配pad copper exposure pad 露銅panel 小型板面;母板panel plating 一次銅電鍍parasitic 寄生的part no. 料號pattern plating 二次銅電鍍PCB ( print circuit board ) 印刷電路板pcs 片peel strength 抗撕強度peeling off 剝離(剝落) performance specification 性能規範permittivity 透電率perspectives on experience 經驗透視PET 聚酯photodiode detector 發光二極體偵測器photo initiator 感光啟始劑photoresist 光阻phototool 光具(指工作底片) piece 子板面pinceton applied research 腐蝕測定儀pink ring 粉紅圈pit 凹點pitch 腳距planar 平面plating 電鍍plating exposure 下鍍層露出plug gauge 插規plug hole 孔塞PNL (panel) 排板polar-polar interaction 極性之間的吸力polyester 聚酯類polyglycols 聚乙二醇polyimide 聚亞醯氨poor bevelling 磨邊加工引起突起,剝離poor drill 孔形不良poor HAL 噴錫不良poor marking 字體不良poor pad 錫墊不良poor printed 印刷偏差poor solderability 焊錫性不良poor touch-up 補線不良position control system 位置控制系統positive rake angle 正摳耙角power curve model 幕次曲線模式practice 工藝慣例preferred 良好premature tearing 提前撕裂prepolymer 預聚合物prepreg 膠片pre-process ( front-end) 製前press 壓床press cycle 壓合週期primary current distribution 一次電流分佈primary 主要product lifetimes 生命週期product process 製程promoter 促進劑protocal 初步資料prussic acid 普魯士酸PTF-based process 厚膜糊法PTH (plating though hole) 導通孔pull away 拉開pumice 浮石粉pumice scrub 噴砂清潔法pyrometallurgy 火燒法冶鍊QC ( quality control) 品管QFP (quad flat pack ) 扁方型封裝體qualification inspection 資格審查檢驗qualification testing 資格檢定quality classification 品質等級quantitative 計量式測試rack 掛架radiometer 能量劑rake angle 摳耙角RAM [Random Access Memory 隨機存取記憶體real time 關鍵時刻recessed trace process 凹槽線路法recovery tank 回收槽reduction 還原re-eninforcement 強化refraction 折光率reinforcement style 補強材料的型式register mark 對位用標記registration hole 對位孔registration pattern 長方形銅地REJ ( reject ) 退貨;拒收rejectable 拒收release agent 脫模劑relief angle 浮離角remark 備註repair 修理resin content 樹脂含量(膠含量) resin flow 膠流量resin flow percentage 樹脂流量之百分率resin recession 樹脂下陷resin smear 膠渣resist strippers 剝乾膜劑resistor network 排列電阻resolution 解像度return on assets 資產報酬率reversibility 可逆性rework 重工rosin 天然松香rotating cylinder 旋轉圓柱形roughtness 孔壁粗糙;粗慥routing 切外形,成型routing bit 銑刀runout 偏轉S/L on hole 孔內沾文字S/M ( solder mask ), S/L 防焊文字S/M (solder mask) 防焊S/M error 防焊種類錯誤S/M on hole 孔內綠漆salt spray test 鹽水噴霧試驗sampling size 抽樣數scope 範圍scored 刻痕scoring 樞槽;刮線scrap 廢框scratches 刮傷screen printing 網版印刷scum 透明殘膜sealing 封孔處理secondary 次要semi-additive 半加成法sensitize 敏化sensitizer 敏化液separator 鋼隔板sequential lamination 漸成式壓法serrated edges 毛邊shatter 破碎short 短路shunt 分路silane treatment 矽烷處理silicone coupling agent 矽烷偶合劑silk screen 文字印刷simulator 模擬器single axis 單軸sizing 底片之伸縮補償skip 漏印skip printing 跳印;漏印sliver 絲條slot 開槽slotting 開槽SMD ( surface mount device ) 表面黏著元件smear 膠渣SMT ( surface mount technology)表面黏著技術sodium carbonate monohydrate 結晶水碳酸鈉soft tooling 軟性工具solder 焊錫; 錫鉛solder bridge 錫橋solder bump 錫突solder float 漂錫solder mask adhesion 綠漆附著力solder on G/F 金手指沾錫solder on trace 線路沾錫solder plug 錫塞solder side 焊錫面solderability 焊錫性solid carbide 實質碳化物spacing 間距spacing nonenough 間距不足SPC ( Statistical Process Control ) 統計生管specification 規範special considerations 特別考慮spin coating 旋轉塗佈spindle 鑽軸spiral contractometer 螺旋收縮儀spot face 銑靶spray coating 噴塗Squeegee 刮刀stacking structure 疊板結構stamping 沖壓standard hydraulic lamination 標準液壓法standardizing 標準化starvation 缺膠step tablet 格片數stock option 認股選擇權strain 應度strength 強度stressmeter 應力計subtractive 減除法surface convex 表面突起surface examination 表面檢查surface insulation resistance (SIR) 表面絕緣電阻surface mount 表面黏著方式surface roughness 表面粗慥度surges 突波switch circuit 開關線路tab 金手指tack free 不黏taped hole gauge 錐形孔規target hole 靶孔task force 任務編組tensile strength 抗拉強度tensile stress 張性應力tent 浮蓋terms and definitions 術語與定義termination load 抗匹配負載test circuit 測試線路test method 試驗方法test point 測試點thermal shock 熱震盪試驗thermal stress 熱應力試驗thermistor 熱電感應式thermo cycling 熱循環試驗theoretical cycle time 理論性週期時間thickness 厚度time to market 上市時機thickness distribution 厚度分佈thief 補助陰極thin core 薄基板;內層板throwing power 分佈力tolerance 公差;容差tooling hole 工具孔torque load 扭力拒之負載total quality program 全面的品質計劃toughness 堅度trace error 線路錯誤trace nick & pin hole 線路缺口及針孔trace peeling 線路剝離trace pin-hole 線路針孔trace surface roughness 線路表面粗糙tarnish and oxide resist 抗污抗氧化劑transmittance 透光度trim line 裁切線true levelling 真平整true position 真正位置的孔;真位twist 板翹type 種類umbra 本影undercut 側蝕uneven coating 噴錫厚鍍不平整universal 萬用型universal tensile tester 萬用拉力試驗機universal tester 汎用型測試機upper carrier 頂部承載鋼uptime 稼動時間vacuum deposition 真空蒸鍍法vacuum hydraulic lamination 真空液壓法vaporizer 氣化室V-cut V形槽vertical microsection 垂直微切片via hole 導通孔visible inventory 有形的庫存vision inspection 目視檢查V oid 孔破void in hole 孔壁上的破洞void in PTH hole 孔破walkman 隨身聽warehouse 倉庫warp 板彎warp , warpage 板彎water absorption 吸水性wear resistance 耐磨度weave exposure 纖紋顯露weave texture 織紋隱現wedge angle 契尖角week 週wet chemistry 濕式化學製程wet film 濕膜wet lamination 濕膜壓膜法wet process 濕製程wetting 沾錫wetting balance 沾錫平衡法wicking 滲銅;滲入;燈蕊效應width 寬度width reduce 線細width-to-thickness ratio 寬度與厚度的比值window 操作範圍work-in-process 在製品work order 工單working film 工作片working master 工作母片year 年yellow 金黃色yield 良率glassy state 玻璃狀態rubbery state 橡膠狀態trial & error 嚐試錯誤SOP 標準作業程序EDI (Exchange data interface) 資料交換介面FTP (file transfer protocol) 檔案傳送協定Web site 網址WAP (wireles application protocol) 無線應用協定series connection 串聯parallel connection 並聯NPI(new Product introduction) 新產品導入sample qualification 打樣認可independent third party assessment 獨立第三者評鑑internal assessment 戶(內部)評鑑end product 完工產品rounding convention 四捨五入之慣例inspection lot 檢驗批target value 目標值horizontal microsection 水平切片order of precedence 優先順序master drawing 主圖making ink 文字油墨thermal plane 散熱層hole-fill insulation material 填孔用絕緣物unsupported holes 非電鍍通孔hole pattern accuracy 孔位準度dielectric layer thickness 介質層厚度lifted lands 焊墊浮起nail-heading 釘頭Plating folds 電鍍皺折tackness 沾黏性sample size 樣本數sampling plan 抽樣計劃rejected lots 拒收批exterior containers 外箱intended use 主要用途non-flow (no-flow) 非流性etchback (when specified) 回蝕(當指定時才做)abrade 動擦掉;擦傷;磨損abrasion 名擦破;擦傷;磨滅;剝蝕abridge 動縮短;省略;抄錄;縮減;剝奪absorbent 形會吸收的;有吸收力的absorbent cotton 形脫脂棉absorption 名吸收;專心;合併abstract 形抽象的;理論的;不專心動摘錄;抽象;偷;轉移提煉;抽取abuse 動濫用;誤用;咒罵;虐待;欺騙acceleration 名加速[度];促進access 名接近;接受;會面;捷徑;通路accessory 形附屬的;補助的;從犯的accommodate 動調節;和解;供應;留;容納accordance 名一致;調和account 名計算;會計;報告;解釋;理由accredit 動相信;認定資格;歸功於.. accumulation 名累積;堆積accurate 形正確的;準確的;精密的accurately 副正確地;精密地acetone 名丙酮[揮發性無色液體achieve 動完成;成就;博得;達到[目的] acid 形酸的;不和悅的;不開心的acknowledge 動認;承認;自白;感謝acknowledgment 名承認;容許名自白;謝禮;禮物;收帖;收條;感謝acoustical 形聽覺的;音響學的acrylic 形壓克力的;丙烯酸的activate 動使活動;催化;淨化;編組activation 名使活動;使催[活]化;活化activator 名使活躍之物;催化劑active 形活動[潑]的;勤勉的;主動的;動態acuity 名銳敏;激烈;苛刻acupuncture 名針灸;針治acute (angle) 形尖銳的;精明的;激烈的;高音的;(銳角)added value 名附加價值addendum 名補遺[書的]附冊;附加物additive 形該加的;加法的;加法的名電池等的]添加劑address 名稱呼;住址;致辭;談吐;請求動演說;申請;免法官之職;說服;追求adequacy 名適當;妥當;足夠adhere 動黏著;附著;固執;信奉;支持adherence 名固執;固守;黏著;附著adherent 形黏著的;附著於;信奉的名支持者;伙伴adhesion 名黏著;膠著;固執;瘉合adjacency 名鄰接[物;地];前後節目adjacent 形鄰近的;鄰接的;附近的administrate 動管理;支配administration 名管理;經營名當局;政府;內閣;給與;配藥;遺產[財政]管理administrative 形管理行政的adopted 形被收養的;被採用的adoption 名採用;收養;過繼;公認advantage 名利益;便利;優勢;優越adversely 副逆地;反對地;不利地advisory 形勸告的;建議的;忠告的aesthetics 名美學affected 形受影響的;感染的;感動的affiliation 名加入;同盟;協力名私生子父親認定;追溯由來;關係;養父子關係affinity 名姻親;同族關係;親近性名遠緣份;嗜好;相處得來的人;親和力affirm 動斷言;確定;肯定;斷定;確認affix 動附加;貼上;簽上;蓋上;使負責against 名對,對著;反對;相逆;依;靠agar 名海菜;紫菜;石花菜;細菌培養基agenda 名會議事項;議事日程;議程agent 名代理者;管理人;代辦人名行為者;手下;作因;天然力;官員;推銷員agglomeration 名結塊;凝結aggravating 形使..惡化的;可惱的aggregate 動聚集;總計;集合;合計的名集合;集團;集合體;材料aggressive 形侵略的;攻勢的;挑釁的形氣勢洶洶的;進取[積極]的;精力旺盛的aging 形上年紀的;變老的;變舊的;老化agitation 名攪動;動搖;興奮;煽動agreement 名契約;協議;符合;同意air force 名空軍alcohol 名酒精;醇;酒;飲酒algorithm 名互除法align 動使成一線;排成一行;排列;合作alignment 名排成直線;整頓;合作aliquot 形能整除[某數的數] alkaline 形鹼屬的;鹼性的alkalinity 名鹼度alleviate 動減輕[痛苦];緩和allocate 動分派;配置;定位置;分配allow 動允許;聽任;給與;斟酌;扣除;想allowance 名津貼;零用金;寬限;斟酌名扣除;許可;承認;折讓;發津貼;給與定量alloy 名合金;成色;賤金屬;混合物動使成合金;減低成色;減少;成合金;攙雜alpha 名希臘字母首字;最初alter 動改變;改造;改作;閹割;去勢;變alteration 名變更;改造alternate 形交互的;間隔的;代理人動交錯陳列;交替;輪流;交流作用alternative 形二中擇一的altitude 名高;高度;海拔高度;高處aluminum 名鋁[金屬元素] ambient 形包圍的ambiguous 形曖昧的;不明確的ambition 名雄心;熱望;野心的目標(志)amide 名氨基化合物ammonia 名氨[氣體];氨水ammoniacal 形氨的;氨性的;含氨的amperage 名安培數amplitude 名廣闊;寬;豐富;充足名振幅;射程;[天體的]出沒方位角analog 名類似物;相似體;類比analogy 名類似;相似;類推anchor 名錨;殿後者;錨紋飾;鑿;急煞車anchoring spur 名著力爪angstrom 名埃[光的波長單位] angular 形有角[稜]的;尖的;瘦的;笨anion 名陰離子anneal 動加熱後退火使其韌化;鍛練;(回火);軔化annex 動附加;追加;併吞;罷佔;侵吞名加添物;附冊;附件;加建建築;別館annotate 動註解[書等];註釋annual 形一年的;每年的;一年生的名一年生植物;年刊書[誌];年報;年鑑annular 形環狀的;輪狀的annuli .. annulus的複數形anode 名正極;陽極anomaly 名不規則;反常;近點離角antimony 名銻[金屬元素] apparatus 名[一套]器具;器官;構造apparent 形顯而易見的;外表上的appendix 名附屬物;附錄;追加;盲腸applicable 形可適用的;能應用的apply 動適用;應用;撫;貼;塗;敷;使用appraisal 名評價;估價;鑑定approach 動接近;近似;向..交涉;研討名接近;近似;入口;[研究]門徑;親近;逼近appropriate 動作為專用;挪用形適當的;特有的;固有的apron 名圍巾;圍嘴;馬車擋雨的遮腳布名法衣;前舞臺;飛機庫前柏油或水泥地;護岸aqueous 形水的;水般的;水成的archives 名公文保管處;擋案;公文arise 動起來;出現;興起;發生;起立;起arithmetic 名算術;算法;計算army 名軍隊;陸軍;大群;團體arose .. arise的過去式array 名打扮;排隊;列舉;召集;軍勢;衣裳ascertain 動確定;稽考;探查aspect 名樣子;光景;容貌;臉相;方向名方位;面;局面;情勢;[星]視座;相;態asphalt 名瀝青;鋪裝用柏油asphaltic 形柏油的aspire 動熱望;懷大志;切望;高聳assembly 名集會;會合;會議;組合assess 動估定;評價;估價;課稅;徵收assessment 名估定;評價;課徵;會費assets 名財產[可作償債者];資產assets and liabilities 名資產與負債assignment 名分配;轉讓;任務assist 動援助;出席;[棒球]補殺assistance 名援助;幫助assistant 名助手;助理;店員associated 形聯合的;關聯的assume 動採取;承擔;假裝;臆測;擺架子assumption 名採取;承擔;假定;傲慢asymmetric 形不均勻的;不對稱的atmosphere 名大氣;情況;環境;氣氛atomizer 名噴霧器;香水噴霧器attachment 名附著;固著;附著物名附屬品;依戀;執著;逮補;拘留attack 動攻擊;襲擊;害病;動手attempt 動嘗試;企圖;窺伺;襲擊;未遂attendant 形跟隨的;出席的;伴隨的名陪從;隨員;伴隨物;從業者;管理員;加油站的站員attenuate 動使變稀薄;使變細;弄淡attenuation 名[使]變薄;稀薄化attestation 名證據;證言;證明attitude 名姿勢;身段;態度;心意attribute 動歸因;認為是..的緣故名屬性;特質;附屬物;象徵;形容詞;屬性attribution 名歸屬;歸因;屬性attributive 形屬性的;形容的;修飾語audience 名聽眾;觀眾;收聽者;收看者audit 名審計;審核;查帳;決算;旁聽aurum 名金[金屬元素] authorization 名授權;委任;認可autoclave 名快鍋之一種auxiliary 形補助的;副的;預備的名幫助者;補助物;外國補助部隊;補助艦;助動avenue 名林蔭路;林蔭道;大路;門徑aware 形知道;曉得;注意到awareness 名知道;曉得;注意axial 形軸的;成軸的;軸周圍的backlight 名背光; backup名支援;滯銷貨;阻塞;背板;備份backward 副向後;相反;以前形向後;落後;怕羞的baggy 形袋狀的;寬鬆而下垂的balance 動秤;抵消;均衡;躊躇名秤;對稱;比較;剩餘;(可指尾數板) balance due 名不足額balance in hand 名餘款bar 名染;妨害;禁止;反對;除..之外名棒;閂;線條;法院;節線bar code 名條碼barometric 形氣壓[計]的barrel 名桶;槍身;選舉費用basket 形籃製的;自備的野餐名籃簍;一籃;籃形的東西bat 名球棒;打手;片;棉絮;蝙蝠動速寫;充分討論;輪到打擊batch 名一爐[麵包等];一組bath 名沐浴;溫泉地;浸漬用水battery 名毆打;電池;投捕手Baume scale 名波美(比重計)beaker 名有倒口的燒杯;大杯beam 動放射;閃亮;微笑;廣播名樑;船幅;秤桿;槓杆;光線behavior 名規矩;品行;作用bellow(s) 動怒吼;咆哮;呼嘯;(風箱(名) bend 動彎;拉;使屈服;傾心beneath 副在..之下;比..差beneficiary 形享受俸祿;臣服的名受益人;公費生benefit 動有益;享受利益;受益名利益;恩惠;義演;給付bevel 名斜角;傾斜;斜面;斜角規動截成斜角;斜切bias 動使存偏見;使偏袒;斜的;交叉的bias 名斜線;成見;傾向;歪斜;偏見bifurcate 動分[成]叉bilateral 形兩邊;有兩面的binary 名二要素合成物;雙子星形兩要素的;二進位的;二元的binder 名裝訂人;使固定的東西;黏結劑bipolar 形有兩極的;雙極的blade 名葉;刃;劍術家;扁平;翼名蕩子;女子;舌的前端blank 形空白的;單調的;完全的;無效的名空虛;鑰匙;空包彈;標準桿孔規bleed 名切印刷部份的頁次動流血;流出樹液;取血;搾bleeder 名易出血或不止的人blend 名混合;混合物;混成語;溶合blender 名混合;混合器;攪拌器;果菜榨汁機blind 動使失去判斷;隱蔽形瞎的;魯莽的;不完全的;遮眼物;欺瞞blip 名雷達映出的影像blister 名水泡;發泡膏;槍座;使煩惱blob 名滴;小斑點;零分;濺block 名石頭;切肉板;滑車;妨礙;佔地方;一區blot 名污痕;棋子;弱點動抹髒;塗掉;吸乾;遮蓋blotting 名乾印(印刷洗紙)blunt 動弄鈍;減弱;變鈍名短粗的針;現金;鈍的;粗魯;生硬;率直的blur 名污髒;矇矓;不清楚;污名動弄髒;使模糊;朦矓blurr 動弄髒;使模糊;朦矓blurry 形模糊的;不清楚的;污斑blush 名面赤;紅;赤色;一瞥動害羞;臉紅;弄紅;使面紅bolt 名挺直;跑開;脫黨;細看名箭頭;電光;拒絕;螺釘bomb 動丟炸彈;轟炸名炸彈;手榴彈;突發事件bond 名結合;契約;證券;保證人形黏土的;被囚禁的booklet 名小冊子;印刷品boost 動由後推;推上;援助;聲援boot 動用靴踢;使穿長靴;電腦開機;起動名靴;放行李處;刑具;利益borderline 名邊界[上的]bound 名境界[線];領域;邊際動跳;使彈回;bind的過去形被縛的;裝訂的;決意的bow 名弓;彎曲;蝴蝶結;槳動鞠躬;屈服;嚮導;使屈服branch 名枝;分枝;支線;分部brand 動打烙印;予以深刻印象名品種;商標;烙印;污名brass 名厚臉皮;高級軍官;黃銅[製品]break 動弄傷;違背;斷;使破產;損壞;闖入名破曉;跑出;阻斷;小憩break-away 名折斷邊breakdown 名故障;挫折;分類;分析名崩潰;倒塌;破損breaker 名碎波;破碎者;切斷機名馴馬師;[飲料用]水桶breakover 名崩潰breath 名氣息;呼吸;低語;微吹brighten 動使輝煌;使快活;使聰brightener 名光澤劑bristle 名剛毛;豬鬃動使豎立毛髮;發怒brittle 形易碎的;短暫的broadly 副寬廣地;明白地;無禮bromide 名溴化物bronze 名青銅[色;製品];古銅browse 動吃嫩葉;放牧;瀏覽名嫩葉;嫩芽;嫩枝brush 名小衝突;叢林灌木地帶名刷;筆;筆法;狐尾;拂拭bubble 名泡;泡沫;詐欺buckle 動扣住;彎曲;起皺;扣緊名釦子;彎曲;皺bud 名芽;花蕾;未發育的;少女;開始發育buffer 名緩衝器;減弱衝突的人bug 名毛病;故障;缺點;錯誤名半翅類的蟲;病菌;蟲動裝置防盜鈴[秘密擴音器] bulge 名脹;腰;凸出部份;優越bull 名公牛;金牛座;買空者名警察;吹牛;靶心;傻事bump 名碰撞聲音;腫塊;搖;撲通動衝撞;碰;交替;免職;顛簸buoyancy 名輕快;樂觀;浮力bureau 名衣屜櫃[大桌];辦公室buret 名滴管;玻璃量管burn 動燒;灼傷;銘感;腐蝕;焦慮burner 名燈口;燒火的;燃燒器burnish 名光輝;光澤動磨;光;光亮;發光burnout 名燃料燒盡;燒壞burr 名光圈;隆隆聲;喉音;鑽孔器;磨刀石bury 動埋葬;葬禮;埋藏;掩蔽busses .. bus的複數bypass 名旁管;迂迴路;忽視;旁路cabinet 名小櫃櫥;會議室;內閣calcium 名鈣[金屬元素] calculate 動計算;預測;指望calibration 名口徑測定;查刻度calipers 名測徑器calorimetry 名熱量測定cam 名凸輪camber 名上彎形[道路];弧形cancellation 名抹消;取消;解除cannister 名罐;茶筒;濾毒罐cant 名哀訴聲;偽善的口吻;黑話;隱語名口號;時髦話;傾斜;斜角;一堆;一滾cap 名無邊帽;頭巾;選手;鞘;套;柱頭;雷管名最高部;修過的輪胎的輪底;臨時參加費capable 形有能力的;可以..的capacitance 名[傳導體的]容量capillary 形毛的;毛細管capital 形首位的;主要的;根本的形優秀的;罪大惡極的;致命的;嚴重的;上好的capital 名首都;大寫;資本;本錢;柱頭captive 名俘虜;迷戀;被囚的;專有的capture 名捕獲;被捕獲者carbide 名碳化物;碳化鈣carbonate 動使成碳酸鹽;碳化carriage 名車;搬運;姿勢;風度carrier 名運送人;信差;搬運器名帶菌者;航空母艦;介質;載波;貨架cash 名錢;現金;小額貨幣cash 動兌現;付現款cashflow 名現金流量catalyst 名觸媒劑category 名種類;部屬;類目caterpillar 名毛蟲;履帶車輛cathode 名陰極cation 名陽離子;陰向游子caul (plate) 名網膜;羊膜囊;髮網;(隔板) caution 名小心;警戒;警告;擔保;吃驚cautiously 副謹慎地;小心地cavitation 名[螺旋槳後的]渦捲;半真空;空泡化cavity 名空穴;空窩;腔;蛀牙洞CCD 名電眼cease 動終止;停頓;停止cell 名小室;密室;茅舍;小屋;墓;滲透者名囊;蜂窩;窩;細胞;電池cellophane 名玻璃紙cellular 形細胞的;劃分的cellular phone 名大哥大行動電話cellulose 名纖維素Celsius 名(度) C (*) centrifugal 形離心的;離心力的centrifuge 名離心分離機centripetal 形向心(性)的ceramics 名窯業;製陶業;陶器certification 名證明;檢定certified 形被證明的;有保證的chalk 動用粉筆記;白粉擦;記錄名粉筆;白粉;記帳出售;眾所珍愛的馬challenge 名挑戰;難題;盤問chamber 名室;會議場;便壺;窩動作房間用;關在室內;上膛。