Crastin PBT S620F20 NC010 物性表
美国杜邦 PA66 HTN501NC010 物性表
HTN501 NC010 is a 30% glass reinforced, flame retardant, lubricated high performance polyamide HTN501 NC010DuPont ™ Zytel ®HTNhigh performance polyamide resinZytel ®ValueDAM50%RHIdentification Part Marking Code ISO 11469>PA6T/XT-GF35FR< Part Marking Code SAE J1344>PPA-GF35FR<Mechanical Stress at Break ISO 527MPa (kpsi)165 (24) Strain at Break ISO 527% 1.6 Tensile Modulus ISO 527MPa (kpsi)13000 (1885) Shear Strength ASTM D 732MPa (kpsi)64 (9.3)70 (10) Flexural Modulus ISO 178MPa (kpsi)12000 (1740)12000 (1740) Flexural Strength ISO 178MPa (kpsi)250 (36)235 (34)Compressive Strength ASTM D 695MPa (kpsi)293 (42.6) Compressive ModulusASTM D 695MPa (kpsi)3580 (520)Notched Charpy Impact Strength ISO 179/1eAkJ/m2-30°C (-22°F)13 23°C (73°F)11 Unnotched Charpy Impact Strength ISO 179/1eUkJ/m2-30°C (-22°F)30 23°C (73°F)40Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm. Test temperatures are 23°C unless otherwise stated.The DuPont Oval Logo, DuPont™, The miracles of science™ and Zytel® are trademarks or registered trademarks of DuPont Company. Copyright© 2008080505/080804The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated; these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-use conditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in thispublication is to be considered as a license to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. CAUTION: Do not use DuPont materials in medical application involving implantation in the human body or contact with internal body fluids or tissues unless the material has been provided from DuPont undera written contract that is consistent with DuPont policy regarding medical applications and expressly acknowledges the contemplated use. For further information, please contact your DuPont representative. You may also request a copy of DuPont POLICY Regarding Medical Applications H-50103-3 and DuPont CAUTION Regarding Medical Applications … H-50102-3Zytel ®resin. It is also a PPA resin.PropertyTest Method UnitsDuring molding, use proper protective equipment and adequate ventilation. Avoid exposure to fumes and limit the hold up time and temperature of the resin in the machine. Purge degraded resin carefully with HDPE.Zytel®ValueDAM50%RHThermalDeflection Temperature ISO 75-1/-2 °C (°F)0.45MPa 270 (518) 1.80MPa260 (500)Melting Temperature ISO 11357-1/-3 °C (°F)10°C/min, First Heat 300 (574)CLTE, Parallel ISO 11359-1/-2E-4/C (E-4/F)-40 - 23°C (-40 - 73°F)0.20 (0.11) 23 - 55°C (73 - 130°F)0.18 (0.10) 55 - 125°C (131 - 257°F)0.18 (0.10)CLTE, Normal ISO 11359-1/-2E-4/C (E-4/F)-40 - 23°C (-40 - 73°F)0.46 (0.26) 23 - 55°C (73 - 130°F)0.50 (0.28) 55 - 125°C (131 - 257°F)0.60 (0.33)Glass Transition Temperature DMA °C (°F)140 (284)90 (194)Electrical Surface Resistivity IEC 60093ohm 1E13 Volume Resistivity IEC 60093ohm m >1E131E13 Electric Strength IEC 60243-1kV/mm (V/mil)1.0mm34 (863)34 (863)Relative Permittivity IEC 602501E2 Hz 3.9 1E3 Hz 3.8 1E6 Hz 3.6Dissipation Factor IEC 60250E-41E2 Hz 80 1E3 Hz 130 1E6 Hz 150Arc Resistance ASTM D 495s 80 CTIIEC 60112V 525Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm. Test temperatures are 23°C unless otherwise stated.The DuPont Oval Logo, DuPont™, The miracles of science™ and Zytel® are trademarks or registered trademarks of DuPont Company. Copyright© 2008080505/080804The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated; these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-use conditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in thispublication is to be considered as a license to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. CAUTION: Do not use DuPont materials in medical application involving implantation in the human body or contact with internal body fluids or tissues unless the material has been provided from DuPont undera written contract that is consistent with DuPont policy regarding medical applications and expressly acknowledges the contemplated use. For further information, please contact your DuPont representative. You may also request a copy of DuPont POLICY Regarding Medical Applications H-50103-3 and DuPont CAUTION Regarding Medical Applications … H-50102-3PropertyTest Method UnitsHTN501 NC010Zytel®ValueDAM50%RHFlammabilityFlammability Classification UL940.81mm V-0Oxygen Index ISO 4589-1/-2%37Hot Wire Ignition UL 746As0.81mm >150 1.5mm >150 3.0mm>150Temperature Index RTI, Electrical UL 746B°C0.81mm 150 1.5mm 150 3.0mm 150RTI, Impact UL 746B°C0.81mm 120 1.5mm 125 3.0mm 130RTI, Strength UL 746B°C0.81mm 130 1.5mm 130 3.0mm150Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm. Test temperatures are 23°C unless otherwise stated.The DuPont Oval Logo, DuPont™, The miracles of science™ and Zytel® are trademarks or registered trademarks of DuPont Company. Copyright© 2008080505/080804The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated; these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-use conditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in thispublication is to be considered as a license to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. CAUTION: Do not use DuPont materials in medical application involving implantation in the human body or contact with internal body fluids or tissues unless the material has been provided from DuPont undera written contract that is consistent with DuPont policy regarding medical applications and expressly acknowledges the contemplated use. For further information, please contact your DuPont representative. You may also request a copy of DuPont POLICY Regarding Medical Applications H-50103-3 and DuPont CAUTION Regarding Medical Applications … H-50102-3PropertyTest Method UnitsHTN501 NC010Zytel®ValueDAM 50%RHOther DensityISO 1183kg/m 3 (g/cm 3)1680 (1.68)Hardness, Rockwell ASTM D 785Scale M 108 Scale R 124Taber AbrasionASTM D 1044mgCS-17 Wheel, 1kg, 1000 cycles 57Water Absorption ASTM D 570%Immersion 24h 0.25Molding Shrinkage ISO 294-4%Normal, 2.0mm 0.5 Parallel, 2.0mm 0.2ProcessingMelt Temperature Range °C (°F)320-330 (610-625) Mold Temperature Range °C (°F)140-160 (280-320)Drying Time, Dehumidified Dryer h 6-8 Drying Temperature°C (°F)100 (210) Processing Moisture Content%<0.10Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm. Test temperatures are 23°C unless otherwise stated.The DuPont Oval Logo, DuPont™, The miracles of science™ and Zytel® are trademarks or registered trademarks of DuPont Company. Copyright© 2008080505/080804The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated; these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-use conditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in thispublication is to be considered as a license to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. CAUTION: Do not use DuPont materials in medical application involving implantation in the human body or contact with internal body fluids or tissues unless the material has been provided from DuPont undera written contract that is consistent with DuPont policy regarding medical applications and expressly acknowledges the contemplated use. For further information, please contact your DuPont representative. You may also request a copy of DuPont POLICY Regarding Medical Applications H-50103-3 and DuPont CAUTION Regarding Medical Applications … H-50102-3PropertyTest Method Units HTN501 NC010。
乐泰620技术数据表说明书
Technical Data SheetLOCTITE®6205月2004产品说明®LOCTITE®620主要适用于圆柱型装配件的粘接.该产品在隔绝氧气的金属密封面间固化，可以防止由于震动或冲击而引起的松动或泄漏.典型用途包括填充紧密配合的压配合件，键沟和花键之间的空隙；装配轴承和衬套，并使压配合键固持强度更高.特别适合用于耐温条件必须达到200°C的情况.固化前的材料特性比重@ 25°C1,16闪点 -见MSDS粘度， Brookfield -RVT, 25°C,mPa·s(cP):转子 5, 转速20rpm5000-12000LMS粘度，EN12092 -MV,25°C,后180s,mPa·s(cP):剪切速度129s-11200-2400典型固化特性固化速度与基材的关系固化速度取决于所用的基材.以下图表显示的是按照ISO10123方法测试，钢制轴和套剪切强度与固化时间的关系以及与其它不同材料之间的比较测试.钢材上的强度固化时间1007550251min5min10min30min1h3h6h24h72h钢铝材重铬酸锌固化速度与间隙的关系固化速度取决于间隙的大小.下图显示在钢制轴和套上，在不同的间隙，剪切强度和时间的关系。
测试标准为ISO10123方法测试.钢材上的强度固化时间1007550251min5min10min30min1h3h6h24h72h.15mm.2mm.5mm固化速度与温度的关系固化速度取决于温度.以下图表显示的是按照ISO10123方法测试，钢制轴和套剪切强度与固化时间及不同温度条件下的测试.钢材上的强度固化时间1007550251min5min10min30min1h3h6h24h72h4°C22°C5°C固化速度与促进剂的关系当固化速度很慢或者间隙较大时，应用促进剂可以加快固化速度.以下图表显示的是按照ISO10123方法测试，620在使用活化剂7471或7649的重铬酸锌钢销和钢套上，在不同固化时间下的破坏强度.钢材上的强度固化时间1007550251min5min10min30min1h3h6h24h72h促进剂7471™促进剂 7649™无促进剂固化后材料典型性能物理性能:热膨胀系数,ISO 11359-2,K -180×10-6 导热系数, ISO 8302, W/(m·K)0,1比热,kJ/(kg·K)0,3模量,断裂时,ISO 37,%<1固化后材料特性胶粘剂性能后24小时 @22°C压剪切强度， ISO 10123:钢制轴和套N/mm² ≥17,2LMS (psi) (2495)固化24小时 @22°C之后进行固化24小时@ 177°C,测试温度@22°C压剪切强度， ISO 10123:钢制轴和套 N/mm² ≥24,1LMS(psi) (3495)典型环境抵抗性能固化1周 @22°C压剪切强度， ISO 10123:钢制轴和套热强度在测试温度下进行强度测试% 强度温度（°C ）1251007550250050100150200250老化强度在测试温度下进行老化,在22°C 进行测试% 初始强度时间2001501005000100500100030005000120 °C150 °C180 °C热老化在特定温度下老化，在22°C下测试% 初始强度时间20015010050100500100030005000120 °C150 °C180 °C耐化学品/溶剂测试在下列条件下进行老化，在22°C 进行测试.初始粘结强度的剩有率%环境°C 100h 500h 1000h 机油(MIL-L-46152)125100100100无铅汽油22959595制动液2210010010050/50乙二醇/水87958080乙醇2210010075丙酮22959595注意事项本产品不宜在纯氧与（或富）富氧氧环境中使用，不能作为氯气或其它强氧化性物质的密封材料使用。
杜邦 PBT HR5330HF 物性表
杜邦PBT HR5330HF本色NC010黑色BK503物性表：产品提供久隆塑胶原料tEL134********CRASTIN®HR5330HF是30％的玻璃纤维增强，高流量（HF)，抗水解（HR）树脂。
耐冲击性及强度出色的平衡性能。
添加剂：润滑剂,、脱模助剂。
特征：可焊、耐化学试剂、水解稳定。
应用：汽车,电子电气。
熔体体积流动速度(MVR)8cm³/10min ISO1133温度250℃ISO1133载荷2.16kg ISO1133模塑收缩率(平行)0.3%ISO294-4,2577模塑收缩率(垂直) 1.0%ISO294-4,2577拉伸模量8500MPa ISO527-1/-2断裂应力110MPa ISO527-1/-2断裂伸长率 2.9%ISO527-1/-2无缺口简支梁冲击强度(+23°C)75kJ/m²ISO179/1eU简支梁缺口冲击强度(+23°C)15kJ/m²ISO179/1eA简支梁缺口冲击强度(-30°C)12kJ/m²ISO179/1eA熔融温度(10°C/min)225°C ISO11357-1/-3热变形温度(1.80MPa)205°C ISO75-1/-2热变形温度(0.45MPa)220°C ISO75-1/-2维卡软化温度(50°C/h50N)215°C ISO306线性热膨胀系数(平行)21E-6/K ISO11359-1/-2线性热膨胀系数(垂直)85E-6/K ISO11359-1/-21.5mm名义厚度时的燃烧性HB class IEC60695-11-10测试用试样的厚度 1.5mm IEC60695-11-10吸水性0.35%类似ISO62吸湿性0.15%类似ISO62密度1500kg/m³ISO1183。
Valox PBT 420SE0
简支梁缺口冲击
0.570 J /厘米
温度-30.0°C
0.600 J /厘米
温度23.0°C
6.20焦耳/平方厘米
温度23.0°C
6.00千焦耳/平方米
@温度-30.0°C
7.00千焦耳/平方米
温度23.0°C
45.0千焦耳/平方米
温度23.0°C
45.0千焦耳/平方米
@温度-30.0°C
5.00焦耳/平方厘米
温度23.0°C
5.00焦耳/平方厘米
温度-30.0°C
简支梁冲击强度
0.600焦耳/平方厘米，
温度-30.0°C
0.700焦耳/平方厘米
17400磅 5毫米/分钟; ISO 527
17400磅 I 型，5毫米/分钟; ASTM D 638
17400磅 5毫米/分钟; ISO 527
0.070％
饱和吸水
0.090％
@温度23.0°C
线性模具收缩，流动 0.0010 - 0.0050厘米/厘
米
0.0050 - 0.0070厘米/厘
米，
厚3.20毫米
线性模具收缩率，横 0.0040 - 0.0080厘米/厘
向
米
0.0050 - 0.010厘米/厘 米，
厚3.20毫米
熔体流动
29 g/10分钟
414 °F 未退火 ASTM D 648
@厚度在0.126
383 °F 雪灵芝120 * 10 * 4 SP
= 100MM; ISO 75/Ae 的
392 °F 80 * 10 * Flatw SP =64
毫米的 ISO 75/Af 的
PA66和PBT的简介
PA66和PBT的简介PA66-(聚酰胺66或尼龙66)聚己二酸己二胺化学式:[-NH(CH2)6－NHCO(CH2)4CO]n－外观:白包或带黄色颗粒状密度:(g/cm3)1．10-1．14 拉伸强度:(MPa) 60. 0-80．0 洛氏硬度:118 冲击强度:(kJ/m2)60-100 静弯曲强度:(MPa)100-120 马丁耐热:(℃)50-60 弯曲弹性模量:(MPa)2000～3000 体积电阻率:(Ωcm)1.83×1015 介电常数:1．63 PA66同PA6相比,PA66更广泛应用于汽车工业、仪器壳体以及其它需要有抗冲击性和高强度要求的产品.聚酰胺66-性状半透明或不透明乳白色结晶形聚合物,具有可塑性.密度1．15g/cm3.熔点252℃.脆化温度-30℃.热分解温度大于350℃.连续耐热80-120℃,平衡吸水率2．5%.能耐酸、碱、大多数无机盐水溶液、卤代烷、烃类、酯类、酮类等腐蚀,但易溶于苯酚、甲酸等极性溶剂.具有优良的耐磨性、自润滑性,机械强度较高.但吸水性较大,因而尺寸稳定性较差.聚酰胺66-应用广泛用于制造机械、汽车、化学与电气装置的零件,如齿轮、滚子、滑轮、辊轴、泵体中叶轮、风扇叶片、高压密封围、阀座、垫片、衬套、各种把手、支撑架、电线包层等.亦可制成薄膜用作包装材料.此外,还可用于制作医疗器械、体育用品、日用品等.聚酰胺66-塑模工艺燥处理:如果加工前材料是密封的，那么就没有必要干燥.然而,如果储存容器被打开,那么建议在85℃的热空气中干燥处理.如果湿度大于0.2%,还需要进行105℃,12小时的真空干燥.熔化温度:260~290℃.对玻璃添加剂的产品为275~280℃.熔化温度应避免高于300℃. 模具温度:建议80℃.模具温度将影响结晶度,而结晶度将影响产品的物理特性.对于薄壁塑件,如果使用低于40℃的模具温度,则塑件的结晶度将随着时间而变化,为了保持塑件的几何稳定性,需要进行退火处理. 注射压力:通常在750~1250bar,取决于材料和产品设计.注射速度:高速（对于增强型材料应稍低一些）. 流道和浇口:由于PA66的凝固时间很短,因此浇口的位置非常重要.浇口孔径不要小于0.5*t(这里t为塑件厚度).如果使用热流道,浇口尺寸应比使用常规流道小一些,因为热流道能够帮助阻止材料过早凝固.如果用潜入式浇口,浇口的最小直径应当是0.75mm.聚酰胺66-化学物理PA66在聚酰胺材料中有较高的熔点.它是一种半晶体-晶体材料.PA66在较高温度也能保持较强的强度和刚度.PA66在成型后仍然具有吸湿性,其程度主要取决于材料的组成、壁厚以及环境条件.在产品设计时,一定要考虑吸湿性对几何稳定性的影响.为了提高PA66的机械特性,经常加入各种各样的改性剂.玻璃就是最常见的添加剂,有时为了提高抗冲击性还加入合成橡胶,如EPDM和SBR等.PA66的粘性较低,因此流动性很好（但不如PA6）.这个性质可以用来加工很薄的元件.它的粘度对温度变化很敏感.PA66的收缩率在1%~2%之间,加入玻璃纤维添加剂可以将收缩率降低到0.2%~1%.收缩率在流程方向和与流程方向相垂直方向上的相异是较大的.PA66对许多溶剂具有抗溶性,但对酸和其它一些氯化剂的抵抗力较弱.PBT-聚对苯二甲酸丁二醇酯属于聚酯系列,是由1.4-pbt丁二醇(1.4-Butyleneglycol)与对苯二甲酸(PTA)或者对苯二甲酸酯(DMT)聚缩合而成,并经由混炼程序制成的乳白色半透明到不透明、结晶型热塑性聚酯树脂.与PET一起统称为热塑性聚酯,或饱和聚酯. PBT为乳白色半透明到不透明、结晶型热塑性聚酯.具有高耐热性、韧性、耐疲劳性,自润滑、低摩擦系数,耐候性、吸水率低,仅为0.1%,在潮湿环境中仍保持各种物性(包括电性能),电绝缘性,但体积电阻、介电损耗大.耐热水、碱类、酸类、油类、但易受卤化烃侵蚀,耐水解性差,低温下可迅速结晶,成型性良好.缺点是缺口冲击强度低,成型收缩率大.故大部分采用玻璃纤维增强或无机填充改性,其拉伸强度、弯曲强度可提高一倍以上,热变形温度也大幅提高.可以在140℃下长期工作,玻纤增强后制品纵、横向收缩率不一致,易使制品发生翘曲. PBT燃烧鉴别:不易燃烧,燃烧时无液体流下,离开火焰后在5秒钟内熄灭,相似于PC.PBT注塑参数1.注射温度:PBT的分解温度为280℃,所以实际生产中一般控制在240-260℃之间.2.注射压力:注射压力一般为50～100MPa.3.注射速率:PBT冷却速度快,因此要采用较快的注射速率.4.螺杆转速和背压:成型PBT的螺杆转速不宜超过80r/min,一般在25～60r/min之间.背压一般为注射压力的10%～15%.5.模具温度:一般控制在70～80℃,各部位的温度差不超过10℃.6.成型周期:一般情况下为15～60s.PBT注意事项1.再生料使用:再生料与新料的比例一般在25%～75%.2.脱模剂使用:一般情况下不使用脱模剂,必要时可采用有机硅脱模剂.3.停机处理:PBT停机时间在30min以内,可将温度降到200℃时停机.长期停机后再生产时,要将料筒内的料排空,再加入新料才能进行正常生产.PA66\PBT厂家东莞湘樟塑化公司，美国杜邦公司，美国杜邦公司，美国液氮公司，基础创新塑料(美国)公司，美国赫斯特公司，美国泰科纳公司，美国普立万公司，美国Chem Polymer公司，美国舒尔曼公司，美国TEKNOR APEX公司，美国RTP公司，德国朗盛公司，美国巴斯夫公司，美国巴斯夫公司，瑞士EMS，台湾耐特，广州金发。
杜邦塑料原料命名规则
杜邦化工在中国销售的塑料原料品牌很多，各个品牌的命名也不尽相同，以下是我补全网上的一些牌号介绍的不足，整理的一份杜邦塑料原料齐全的杜邦塑料原料产品型号命名规则资料，关注我可了解的更多塑料动态。
各种产品等级Crastin.PBT¡. SK = 玻纤增强的树脂¡. S=未增强树脂¡. LW = 低翘曲树脂¡. T=增韧树脂¡. ST = 超韧级别¡. HR= 抗水解改良词尾¡. HF=高流动¡. FR=UL-94 V-0 树脂Delrin. POM多数Delrin. 产品被编码以3 个或4 个数字以第一数字(如果3 数字共计) 或第一2 个数字(如果4 个数字共计) 近似地代表融解流速的. (使用ISO1133标准, 与2 .16 KG装载, g/10min) 。
因而, 100系列是黏度最高的系列(或最低的融指), 300, 500, 900,以此类推流动性越来越高。
多数等级被编码正如每以下例子:Delrin. 500P NC010Delrin. - 产品系列和注册商标500 -产品编码P - 词尾NC010 .-颜色代码编码.-特例X00 系列.-经常是“classic〞均聚物一般用途等级X00P 系列.-基于一个改良的热量稳定系统; 这些通用级别的均聚牌号有在更大的范围内更好的稳定性。
X11P 系列.-同P一样经热稳定改良，在通用均聚物和改良级别中提高了结晶成型周期, 降低模具收缩, 减少翘曲和的空隙, 并且增强注塑制件的尺寸稳定。
X60 系列.-共聚物一般用途等级X07 系列.-紫外稳定等级。
X27UV 系列.-是热稳定和紫外稳定等级。
X50 系列.-挤出等级编码.-前缀DE .-发展或商业代码, 随机号编码.-后缀含义AL .-添加先进的润滑剂KM.- Kevlar® 改良ST .-超韧P .-热稳定改良T .-增韧MT .-半增韧UL.-紫外稳定AS.-抗静电/加硬AT.-抗静电/增韧ATB .- 抗静电/增韧, 选择级CM .-X42CM 2次加工成型AF .-PTFE与Teflon.填充CL .-添加化学润滑剂LM .-可做激光标志TL .-添加PTFE 润滑剂GR .-玻纤增强MF .-矿物填充E .-低放射性DP .-尺寸稳定和高产量级Delrin的颜色代码NC010 .-自然色为通用等级NC000 .-自然色为GR 或MF 等级BK602, 402 .-标准黑代码BK601, 401 .-黑色防UV级别BK000 .-黑色代码某些被填充的级别BKL001 .-可做激光标志的颜色代码(在这种情况下为黑色)** 注意.-在某些情况下, 可以是没有颜色代码的如500Hytrel.TPEEHytrel. 高性能和通用级别全部以四位数命名原则命名, 典型的通用级别是在数字前面加G 。
乔顿 25020 快干环氧云铁中间漆M20 产品技术说明书
快干环氧云铁中间漆M20 (0P7)这是一种双组份聚胺固化环氧涂料。
它是具有含云母氧化铁颜料和高固体含量等特点的厚浆型产品。
在大气环境下适合作为新建项目的中间漆。
适用于经认证的涂装体系。
认证和证书对以下认证有加分贡献:颜色白色、 浅黄色、 浅灰色、 中灰色、 灰色、 灰色XO、 深灰色、 白色、 红色典型用途适合曝露于腐蚀环境的钢结构。
推荐用于炼化厂、发电厂、建筑和矿业设备。
性能测试/标准描述光泽度 (GU 60 °)ISO 2813VOC - 美国 / 香港US EPA 方法 24 (测试值)(CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)VOC- 欧盟IED (2010/75/EU) (理论值)闪点ISO 3679 方法 125 ℃哑光（0-35）250 克/升205 克/升密度1.6kg/l理论值VOC- 中国GB/T 23985-2009 (经测试)185 克/升所列数据是基于工厂批量生产的产品，因颜色不同会有些许变化。
光泽描述: 根据佐敦功能涂料的定义湿膜厚度理论涂布率10012583003752.7微米微米平方米/升---该产品可用以下方式施工喷涂:使用无气喷涂。
刷涂:推荐在预涂和小面积涂装时使用。
必须注意达到规定的干膜厚度。
4份份1快干环氧云铁中间漆M20 组份B稀释剂:佐敦17号稀释剂当作为雾喷使用时，可能需要更高比例的稀释。
注意：当韩国VOC法规《韩国清洁空气保护法》和它对应的稀释限值与推荐稀释体积不同时，以前者为准。
最大稀释:10%喷嘴孔径 (inch/1000):喷嘴压力 （最小）:17-27150 bar/2100 psi在中国，清洗剂必须符合GB 38508-2020的要求可踩踏干燥42 小时26 小时12 小时7 小时 4 小时 2 小时21 天13 天8 天 4 天 3 天0 ℃5 °C10 ℃23 °C40 °C干燥/固化至可使用-5 °C干燥后复涂，最短间隔40 小时24 小时10 小时6 小时3 小时 1 小时23 °C 温度干燥，大气环境中℃120连续的峰值140℃以上温度下，保护性能不受影响。
PBT 杜邦 S600F10 物性表
PBT杜邦DUPONT S600F10物性表：产品提供久隆塑胶原料tEL134********PBT DUPONT Crastin®S600F10NC010是未增强聚对苯二甲酸乙二醇酯纯树脂，润滑，高粘度，注塑成型。
特别适宜成型厚壁产品。
加工方法:注塑,异型材挤出成型,其它挤出成型,表面涂层.Crastin®S600F10is an unreinforced,lubricated,high viscosity polybutylene terephtalate for injection molding.熔体体积流动速度(MVR)10cm³/10min ISO1133温度250°C ISO1133载荷 2.16kg ISO1133模塑收缩率(平行) 1.7%ISO294-4,2577模塑收缩率(垂直) 1.6%ISO294-4,2577拉伸模量2700MPa ISO527-1/-2屈服应力57MPa ISO527-1/-2屈服伸长率4%ISO527-1/-2名义断裂伸长率>50%ISO527-1/-2拉伸蠕变模量(1h)2300MPa ISO899-1拉伸蠕变模量(1000h)1800MPa ISO899-1无缺口简支梁冲击强度(+23°C)N kJ/m²ISO179/1eU无缺口简支梁冲击强度(-30°C)N kJ/m²ISO179/1eU简支梁缺口冲击强度(+23°C) 5.4kJ/m²ISO179/1eA简支梁缺口冲击强度(-30°C)4kJ/m²ISO179/1eA熔融温度(10°C/min)225°C ISO11357-1/-3玻璃化转变温度(10°C/min)55°C ISO11357-1/-2热变形温度(1.80MPa)50°C ISO75-1/-2热变形温度(0.45MPa)115°C ISO75-1/-2维卡软化温度(50°C/h50N)175°C ISO306线性热膨胀系数(平行)130E-6/K ISO11359-1/-2线性热膨胀系数(垂直)130E-6/K ISO11359-1/-21.5mm名义厚度时的燃烧性HB class IEC60695-11-10测试用试样的厚度 1.5mm IEC60695-11-10UL注册UL--厚度为h时的燃烧性HB class IEC60695-11-10测试用试样的厚度0.8mm IEC60695-11-10UL注册UL--燃烧性－氧指数22%ISO4589-1/-2相对介电常数.(100Hz) 3.8-IEC60250相对介电常数.(1MHz) 3.2-IEC60250介质损耗因子(100Hz)20E-4IEC60250介质损耗因子(1MHz)200E-4IEC60250体积电阻率>1E13Ohm*m IEC60093表面电阻率1E15Ohm IEC60093介电强度26kV/mm IEC60243-1相对漏电起痕指数600-IEC60112吸水性0.5%类似ISO62吸湿性0.2%类似ISO62密度1300kg/m³ISO1183熔体密度1110kg/m³-熔体0.21W/(m K)-熔体的比热2100J/(kg K)-注塑成型参数：干燥温度110-130°C干燥时间，除湿机=2-4小时处理水分含量<0.04％熔体温度处理最佳=250°C熔体温度范围240-260°C模具温度最佳=80°C模具温度范围30-130°C型材挤出参数：干燥温度110-130°C干燥时间，除湿机=2-4小时处理水分含量<0.04％熔体温度处理最佳=250°C熔融温度范围为240-260°C。
A106化学成分表
C <=0.3
Si >=0.1
Mn
P
S
0.29~1.06 <=0.035 <=0.035
Cr
Mo
Cu
<=0.40 <=0.15 <=0.40
Ni <=0.4
V <=0.08
WPC
a234
C≤
Mn P≤ S≤ Si Cr
Mo Ni Co
a403 C Mn P S Si Ni Cr Mo Ti
70000-95000 (485-655)
70000-95000 (485-655)
450-620
Ni-10- 70000-95000
0.25
425-625
65000-90000 -
425-655
N-0.08- 90000-115000
0.20
620-795
Yield Strip/ Round
40 275 35 240 40 275 30 205 65
450
Elongation %
ASTM GRADE
A815 WP 27
C 0.01
A815 WP 430 0.12
A815 WP 446
0.2
A815 WP 410
A790 UNS S 31803
TOP
0.15 0.03
Mn 0.75
1 1.5 1 2
Si 0.4 1 0.75 1 1
S 0.02 0.03 0.03 0.03 0.02
A 403/403M 0.03
2
WP 316 L
max.
A 403/403M 0.08
FR50NC010
修订： 2016-06-21 To find out more, visit DuPont Performance Polymers or contact nearest DuPont location.
North America Tel: +1 302 999-4592 Toll-Free (USA): 800 441-0575
测试标准 测试标准 ISO 527-1/-2 ISO 527-1/-2 ISO 527-1/-2 ISO 179/1eA 测试标准 ISO 75-1/-2 UL 746B
UL 746B
UL 746B
测试标准 IEC 60695-11-10 IEC 60695-11-10 UL 94 IEC 60695-11-10 IEC 60695-11-10 UL 94 IEC 60695-11-20 IEC 60695-11-20 UL 94 ISO 3795 (FMVSS 302) ISO 3795 (FMVSS 302) 测试标准 IEC 60112 测试标准 ISO 1183 类似ISO 62 测试标准 -
Page: 2 of 2
单位 -
单位 % % 单位 MPa MPa % kJ/m² 单位 °C
130 / *
°C
130 / *
°C
130
°C
105
°C
115 / *
°C
115
°C
105 115 / *
120 干态/调节后 V-0 / * 1.5 / * yes / * V-0 / * 0.75 / * yes / * 5VA / * 1.5 / * yes / * V-0 / *
PRODUCT INFORMATIቤተ መጻሕፍቲ ባይዱN
CRASTIN SK605 NC010
DuPont™ Crastin® PBTthermoplastic polyester resinCrastin® SK605 NC010Crastin® SK605 NC010 is a 30% glass fiber reinforced, lubricated polybutylene terephthalate resin for injection molding.Property Test Method Units ValueIdentificationResin Identification ISO 1043PBT-GF30Part Marking Code ISO 11469>PBT-GF30< MechanicalStress at Break ISO 527MPa (kpsi)140 (20.3)Strain at Break ISO 527% 2.7Tensile Modulus ISO 527MPa (kpsi)10000 (1450)Tensile Creep Modulus ISO 899MPa (kpsi)1h9000 (1305)1000h6600 (957)Flexural Modulus ISO 178MPa (kpsi)9000 (1300)Flexural Strength ISO 178MPa (kpsi)200 (29.0)Notched Charpy Impact Strength ISO 179/1eA kJ/m2-40°C (-40°F)10-30°C (-22°F)1123°C (73°F)11Unnotched Charpy Impact Strength ISO 179/1eU kJ/m2-40°C (-40°F)75-30°C (-22°F)7523°C (73°F)70Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc.ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm.Test temperatures are 23°C unless otherwise stated.The DuPont Oval Logo, DuPont™, The miracles of science™ and Crastin® are trademarks or registered trademarks of DuPont Company. Copyright© 2005.050330/050331 The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated;these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise.The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-useconditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in this publication is to be considered as alicense to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. Caution: Do not use this product in medical applications involving permanent implantation in the human body.For other medical applications see "DuPont Medical Caution Statement", H-50102.Crastin® SK605 NC010Property Test Method Units ValueThermalDeflection Temperature ISO 75f °C (°F)0.45MPa220 (428)1.80MPa205 (401)Melting Temperature ISO 11357-1/-3 °C (°F)10°C/min225 (437)CLTE, Normal ISO 11359-1/-2E-4/C (E-4/F)23 - 55°C (73 - 130°F)0.90 (0.50)CLTE, Parallel ISO 11359-1/-2E-4/C (E-4/F)23 - 55°C (73 - 130°F)0.30 (0.20)Vicat Softening Temperature ISO 306 °C (°F)10N221 (429)50N213 (415)Hot Ball Pressure Test VDE 0470°CPlate 3mm210ElectricalSurface Resistivity IEC 60093ohm>1E15Relative Permittivity IEC 602501E2 Hz 4.41E6 Hz 3.8Volume Resistivity IEC 60093ohm m>1E13Dissipation Factor IEC 60250E-41E2 Hz251E6 Hz180Electric Strength IEC 60243-1kV/mm (V/mil)1.0mm31 (787)20s, Plate 2mm17 (431)Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc.ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm.Test temperatures are 23°C unless otherwise stated.The DuPont Oval Logo, DuPont™, The miracles of science™ and Crastin® are trademarks or registered trademarks of DuPont Company. Copyright© 2050330/050331 The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated;these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise.The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-useconditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in this publication is to be considered as alicense to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. Caution: Do not use this product in medical applications involving permanent implantation in the human body.For other medical applications see "DuPont Medical Caution Statement", H-50102.Crastin® SK605 NC010Property Test Method Units ValueElectricalElectrolytical Corrosion IEC 60426Plate 4mm A1CTI IEC 60112V450CTI UL 746A V3.0mm400CTI M IEC 60112Plate 4mm200 FlammabilityFlammability Classification IEC 60695-11-100.75mm HBFlammability Classification UL940.75mm HBOxygen Index ISO 4589-1/-2%19Glow Wire Flammability Index IEC 60695-2-12°C0.75mm7251.5mm7253.0mm825Glow Wire Ignition Temperature IEC 60695-2-13°C0.75mm7501.5mm7503.0mm800High Amperage Arc Ignition Resistance UL 746A arcs1.5mm603.0mm1206.0mm120Hot Wire Ignition UL 746A s1.5mm153.0mm306.0mm120Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc.ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm.Test temperatures are 23°C unless otherwise stated.The DuPont Oval Logo, DuPont™, The miracles of science™ and Crastin® are trademarks or registered trademarks of DuPont Company. Copyright© 2050330/050331 The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated;these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise.The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-useconditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in this publication is to be considered as alicense to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. Caution: Do not use this product in medical applications involving permanent implantation in the human body.For other medical applications see "DuPont Medical Caution Statement", H-50102.Crastin® SK605 NC010Property Test Method Units ValueTemperature IndexRTI, Electrical UL 746B°C0.75mm130RTI, Impact UL 746B°C0.75mm130RTI, Strength UL 746B°C0.75mm130OtherDensity ISO 1183kg/m3 (g/cm3)1530 (1.53)Ball Indention Hardness ISO 2039-1MPa (kpsi)H 961/30200 (29)Water Absorption ISO 62, Similar to%Equilibrium 50%RH0.13Saturation, immersed0.37Molding Shrinkage ISO 294-4%Normal, 2.0mm 1.1Parallel, 2.0mm0.3ProcessingMelt Temperature Range °C (°F)240-260 (465-500)Melt Temperature Optimum °C (°F)250 (480)Mold Temperature Range °C (°F)30-130 (85-265)Mold Temperature Optimum °C (°F)80 (175)Drying Time, Dehumidified Dryer h2-4Drying Temperature °C (°F)110-130 (230-265)Processing Moisture Content%<0.04Snake Flow mm100MPa, 7 x 2mm37590MPa, 5x0.30mm990MPa, 5x0.50mm3790MPa, 5x0.75mm7590MPa, 5x1.00mm119Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc.ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm.Test temperatures are 23°C unless otherwise stated.The DuPont Oval Logo, DuPont™, The miracles of science™ and Crastin® are trademarks or registered trademarks of DuPont Company. Copyright© 2050330/050331 The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated;these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise.The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-useconditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in this publication is to be considered as alicense to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. Caution: Do not use this product in medical applications involving permanent implantation in the human body.For other medical applications see "DuPont Medical Caution Statement", H-50102.。
马氏体不锈钢的钢号、化学成分和性能特点
马氏体不锈钢1、常用马氏体不锈钢的钢号、化学成分和性能特点。
1、 Cr13型（1）此类钢的化学成分见表2-8表2-8 1Cr13,2Cr13,3Cr13,4Cr13钢的化学成分， %①① GB1220-92(2)力学性能1Cr13,2Cr13,3Cr13,4Cr13 钢的力学性能分别见表2-9至表2-16。
表2-9 1Cr13钢的室温力学性能①摘自GB1220，硬度为退火或高温回火后的数值②实际生产检验值，钢材截面尺寸≤60mm表2-10 1Cr13钢的高温力学性能表2-11 2Cr13钢的室温力学性能①摘自GB1220，硬度为退火或高温回火后的数值；②实际生产检验值，钢材截面尺寸≤60mm，硬度为退火后硬度值。
表2-12 2Cr13钢的高温力学性能表2-13 3Cr13钢的室温力学性能①摘自GB1220，括号内硬度系退火或高温回火后的布氏硬度；②实际生产检验值。
表2-14 3Cr13钢的高温力学性能表2-15 4Cr13钢的室温力学性能①摘自GB1220；②实际生产检验值。
表2-16 4Cr13钢的高温力学性能（3）耐蚀性能1Cr13,2Cr13,3Cr13,4Cr13 钢均具有不锈性。
在室温的稀硝酸以及弱有机酸中也有一定耐蚀性。
1Cr13和2Cr13钢在某些介质中的耐蚀性能见表2-17和表2-18表2-17 1Cr13钢的耐蚀性能表2-18 2Cr13钢的耐蚀性能（4）工艺性能包括冷、热加工性能、热处理性能及焊接性能。
1Cr13钢的冷塑性及深冲性、抛光性和切削加工性能均良好，其板材厚度与深冲度的关系见图2-49。
它的热加工温度以850-1200℃为宜，随后需灰冷或砂冷。
它的焊接性能与0Cr13相近，焊后若焊缝需进行机加工时，应进行退火处理。
1Cr13钢的热处理工艺见表2-19。
图2-49表2-19 1Cr13钢的热处理工艺2Cr13钢冷塑性变形性能、深拉和深冲性以及切削加工性均尚好，它的热加工温度以850-1200℃为宜，随后需砂冷或及时进行退火处理。
PBT
产品特征
产品
－特性
应用范围
PBT
树
脂
-耐水解性好；
-吸湿性低，对电气及尺寸稳定性影响极小；
-耐化学品、溶剂、耐候性佳；
-结晶速度快，流动性好，成型性优良；
-介电强度高，电气性能佳；
-耐热性佳；
-磨擦系数低，耐磨耗；
-弯曲蠕变性好；
模具温度：对于未增强型的材料为40～60C。要很好地设计模具的冷却腔道以减小塑件的弯曲。热量的散失一定要快而均匀。建议模具冷却腔道的直径为12mm。
注射压力：中等（最大到1500bar）。
注射速度：应使用尽可能快的注射速度（因为PBT的凝固很快）。
流道和浇口：
建议使用圆形流道以增加压力的传递（经验公式：流道直径＝塑件厚度＋1.5mm）。可以使用各种型式的浇口。也可以使用热流道，但要注意防止材料的渗漏和降解。浇口直径应该在0.8～1.0＊t之间，这里t是塑件厚度。如果是潜入式浇口，建议最小直径为0.75mm。
化学和物理特性：
PBT是最坚韧的工程热塑材料之一，它是半结晶材料，有非常好的化学稳定性、机械强度、电绝缘特性和热稳定性。这些材料在很广的环境条件下都有很好的稳定性。PBT吸湿特性很弱。
非增强型PBT的张力强度为50MPa，玻纤添加剂型的PBT张力强度为170MPa。玻纤添加剂过多将导致材料变脆。PBT的；结晶很迅速，这将导致因冷却不均匀而造成弯曲变形。对于有玻纤添加剂类型的材料，流程方向的收缩率可以减小，但与流程垂直方向的收缩率基本上和普通材料没有区别。一般材料收缩率在1.5％～2.8％之间。含30％玻纤添加剂的材料收缩0.3％～1.6％之间。熔点（225℃）和高温变形温度都比PET材料要低。维卡软化温度大约为170℃。玻璃化转换温度（glasstrasitiotemperature）在22℃到43℃之间。
PBT+PTFE 杜邦 Crastin S600LF 物性表
拉伸模量 2700MPa ISO 527-1/-2 屈服应力 58 屈服伸长率 MPa ISO 527-1/-2 7.5 % 15 % ISO 527-1/-2 % ISO 527-1/ISO 179/1eU ISO 179/1eU ISO 179/1eA ISO 179/1eA ISO 180/1A
150 °C ISO 75-1/-2 class IEC 60695-11-10
测试用试样的厚度 0.8 mm 吸水性 吸湿性 0.4 % 0.2 %
IEC 60695-11-10
类似ISO 62 类似ISO 62 ISO 1183
密度1320 kg/m³
® PBT+PTFE 杜邦 Crastin® S600LF NC010 物性表：润滑，耐磨，低摩擦系数, 可焊接，耐化学 性。 产品供应 久隆塑胶原料 tEl 134 169 58072 模塑收缩率 (平行) 模塑收缩率 (垂直) 2.2 % 2.2 % ISO 294-4, 2577 ISO 294-4, 2577
无缺口简支梁冲击强度 (+23°C) 145 kJ/m² 无缺口简支梁冲击强度 (-30°C) 100 kJ/m² 简支梁缺口冲击强度 (+23°C) 简支梁缺口冲击强度 (-30°C) 悬臂梁缺口冲击强度 (23°C) 4 3 4 kJ/m² kJ/m² kJ/m²
熔融温度 (10°C/min) 225 °C ISO 11357-1/-3 热变形温度 (1.80 MPa) 热变形温度 (0.45 MPa) 厚度为h时的燃烧性 HB 55 °C ISO 75-1/-2
B4406G6 物性表
® B 4406 G602/2005UltradurPBT-GF30Product descriptionInjection molding grade with 30 % glass fibers for parts requiring enhanced fire resistance (eg potentiometer parts,plug-and-socket connectors, switches).Abbreviated designation according to ISO 1043-1:PBT FR(17)CLASSIFICATION ACCORDING TO ISO 7792-1:Moulding Compound ISO 7792-PBT, MFGHLNR, 09-110, GF30Physical form and storageStandard packaging includes the 25-kg-bag and the 1000 kg octabin (octagonal container). Other forms of packaging arepossible subject to agreement. All containers are tightly sealed and should be opened only immediately prior toprocessing. Further precautions for preliminary treatment and drying are described in the processing section of thebrochure. The bulk density is about 0,7 to 0,8g/cm³.Under normal conditions Ultradur can be stored for unlimited periods. Even at elevated temperatures, e.g. 40°C in air, andunder the action of sunlight and weather no decomposition reactions occur.Ultradur should generally have a moisture content of less than 0,04% when beeing processed.In order to ensure reliable production, therefore, pre-drying should generally be the rule and the machine should be loadedvia a closed conveyor system. Appropriate equipment is commercially available. Pre-drying is also for the addition ofbatches, e.g. in the case of inhouse pigmentation.In order to prevent the formation of condensed water, containers stored in unheated rooms must only be opened whenthey have attained the temperature prevailing in the processing area. This can possibly take a very long time.Measturements have shown that the interior of a 25-kg bag originally at 5°C had reached the temperature of 20°C in theprocessing area only after 48 hours.Product safetyUltradur melts are stable at temperatures up to 280°C and do not give rise to hazards due to molecular degradation or theevolution of gases and vapors. Like all thermoplastic polymers, however, Ultradur decomposes on exposure to excessivethermal stresses, e.g. when it is overheated or as a result of cleaning by burning off. In such cases gaseousdecomposition products are formed. Decomposition accelerates above 350°C small quantities of aldehydes and saturatedand unsaturated hydrocarbons are also formed. When Ultradur is properly processed and there is adequate suction at thedie no risks to health are to be expected.Further safety information see safety data sheet of individual product.Safety data sheet could be ask for at the Ultra-Infopoint under tel: 0621/60-78780 or fax:0621/60-78730.NoteThe data contained in this publication are based on our current knowledge and experience. In view of the many factorsthat may affect processing and application of our product, these data do not relieve processors from carrying out their owninvestigations and tests; neither do these data imply any guarantee of certain properties, nor the suitability of the productfor a specific purpose. Any descriptions, drawings, photographs, data, proportions, weights etc. given herein may changewithout prior information and do not constitute the agreed contractual quality of the product. It is the responsibility of therecipient of our products to ensure that any proprietary rights and existing laws and legislation are observed.In order to check the availability of products please contact us or oursales agency.Ultradur® B 4406 G6 ArrayFootnotes1) If the product definition doesn't state otherwise.2) Specimens according to CAMPUS.。
铁霸润滑油颜色对照表
润滑油型号 MEGALUBE极压复合锂基润滑脂（铁霸绿油脂） B.R.GREASE 高温极压润滑脂（铁霸红油脂） BLACK MAGIC磺化钙基复合润滑脂（铁霸黑油脂） MG2-GREASE二硫化钼锂基润滑脂（铁霸二硫化钼油脂） TM COMPLEX合成复合锂基润滑脂 LEP ALUMINUM合成复合铝基润滑脂 AQUA500复合磺化钙润滑脂 TP2122高速封闭轴承润滑脂 TP2128重负载工业润滑脂 TP2133极压开放式齿轮润滑脂 TP2168高温耐水工业润滑脂 TP2329工业轴承润滑脂 BM2000多用途重工业润滑脂 LICAL-LUBE重型设备润滑脂 KUPFAR COMPOUND高温防卡润滑脂 SUPER LUBE PLUS合成食品级润滑脂 METAL CONDITIONER金属抗磨剂 REFRIGERATION SYSTEM METAL CONDITIONER 铁霸制冷系统金属抗磨剂 AUTO-ENERGIZER铁霸汽车加能液 BIG7超级齿轮润滑油 SYNTHETIC GEAR OIL极压合成齿轮润滑油 SYNMOLY合成齿轮油 WIND TURBINE GEAR OIL铁霸风力发电机齿轮油 POWERLUBE多用途开式齿轮润滑剂 MINELUBE 600C高性能开式齿轮润滑剂 E-LUBE X非沥青开式齿轮润滑剂 HYDRO LUBE合成抗磨液压油 SPACO合成空压机润滑油 T-919HT高温链条润滑油 NO CARB SUPER食品级高温链条油 TRI-WIRE ROPE钢缆索润滑油 ROPE LUBE PLUS钢缆索润滑剂 LOWTEMP 1000 NANO SYNTHETIC MOTOR OIL 纳米超低温合成发动机油 KB72-89极压锂基润滑脂 L.D.L.-1多用途超级抗磨喷剂 FUTURE SOLV 1200电器快速清洁剂 M30多功能清洁膏 2013年8月16日 战斗不息整理 棕色 透明黄色 透明金黄色 深灰色 黑色 颜色 绿色 红色 黑色 深灰色 黄色 绿色 水绿色 茶色 棕色 黑色 棕色 茶色 深褐色/黑色 蓝色 铜色 透明 浅琥珀色/Байду номын сангаас黄色 深灰色 深棕色 红色