RFID射频卡调试程序

char RxBuf[1 + MAX_SIZE]; // 接收缓冲区
int BufP = 0; // 缓冲区位置变量
tBoolean RxEndFlag = false; // 接收结束标志
unsigned char WriteULPage5[]= {0xBA,0x07,0x11,0x05,0x11,0x22,0x33,0x44};
unsigned char HD0031CMD_Halt[] = {0xBA,0x03,0x50,0x00};
//------------------global variable define-------------------------------
unsigned char WriteBlock1[]= {0xBA,0x13,0x04,0x01,0x00,0x11,0x22,0x33,0x44,0x55,0x66,0x77,0x88,0x99,0xAA,0xBB,0xCC,0xDD,0xEE,0xFF};
SysCtlPeriEnable(RFID_OUT_PERIPH); // 使能OUT所在的GPIO端口
GPIOPinTypeIn(RFID_OUT_PORT, RFID_OUT_PIN); // 设置OUT所在的管脚为输入
#define RFID_IN_PERIPH SYSCTL_PERIPH_GPIOA
#define RFID_IN_PORT GPIO_PORTA_BASE
#define RFID_IN_PIN GPIO_PIN_7
unsigned char g_cCardType;
unsigned long int g_iTimer;
unsigned char g_bOverTime;
unsigned char g_cUartTxCnt;
unsigned char g_cUartTxDataLen;
unsigned char *g_pUartTxDat;
#define RFID_OUT_PERIPH SYSCTL_PERIPH_GPIOA
#define RFID_OUT_PORT GPIO_PORTA_BASE
#define RFID_OUT_PIN GPIO_PIN_6
UARTFIFOLevelSet(UART2_BASE, // 设置发送和接收FIFO深度
UART_FIFO_TX4_8, // 发送FIFO为2/8深度（4B）
#include "systemInit.h"
#include <uart.h>
#include <ctype.h>
#include <string.h>
#define UARTCharGetNB UARTCharGetNonBlocking
//------------------管脚定义---------------------------------------
unsigned char ReadValue[]= {0xBA,0x03,0x05,0x05};
unsigned char WriteValue[]= {0xBA,0x07,0x06,0x08,0x00,0x00,0x00,0x01};
unsigned char IncrementValue[]= {0xBA,0x07,0x08,0x04,0x00,0x00,0x00,0x20};
unsigned char DecrementValue[]= {0xBA,0x07,0x09,0x04,0x03,0x00,0x00,0x00};
UARTCharPut(UART2_BASE, dat[i]);
}
UARTCharPut(UART2_BASE, Tx_CheckSum);
}
//--------------HD0031 test procedure------------------------------------------
IntEnable(INT_UART2); // 使能UART总中断
IntMasterEnable(); // 使能处理器中断
UARTEnable(UART2_BASE); பைடு நூலகம் // 使能UART端口
unsigned char LoginSector1[]= {0xBA,0x0A,0x02,0x01,0xAA,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF};
unsigned char ReadBlock1[]= {0xBA,0x03,0x03,0x08};
GPIOPinTypeUART(GPIO_PORTG_BASE, // 配置RX/TX所在管脚为
GPIO_PIN_0 | GPIO_PIN_1); // UART收发功能
//-------------------------------------------------------------------
unsigned char SelectCard[]= {0xBA,0x02,0x01};
unsigned char LoginSector0[]= {0xBA,0x0A,0x02,0x08,0xAA,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF};
void RFID_init_HD0031(void)
{
SysCtlPeriEnable(RFID_IN_PERIPH); // 使能超IN所在的GPIO端口
GPIOPinTypeOut(RFID_IN_PORT, RFID_IN_PIN); // 设置IN所在的管脚为输出
strncpy(s, RxBuf, size);
s[MAX_SIZE] = '\0';
return(n);
}
//-----------------------------------------------------------------------------
unsigned char g_cUartTxCheckSum;
unsigned char g_cUartRxCnt=0;
char g_cUartRxBuf[60];
unsigned char g_cUartStatus;
unsigned char g_RXauth;
//------------------RFID初始化---------------------------------------
void Test_HD0031(void)
{
unsigned char counter;
if(GPIOPinRead(RFID_OUT_PORT, RFID_OUT_PIN)!=0x00)return;
// 以FIFO中断方式接收一个字符串，不回显，返回实际接收到的有效字符数
int uartFIFOGets(char *s, int size)
{
int n;
while (!RxEndFlag);
n = BufP;
BufP = 0;
RxEndFlag = false;
void SendBuf_UART(unsigned char *dat)
{
unsigned char Tx_CheckSum=0;
unsigned char i,len;
len=dat[1]+1;
for(i=0;i<len;i++)
{
Tx_CheckSum=Tx_CheckSum^dat[i];
}
// UART初始化
void uartInit(void)
{
SysCtlPeriEnable(SYSCTL_PERIPH_UART2); // 使能UART模块
SysCtlPeriEnable(SYSCTL_PERIPH_GPIOG); // 使能RX/TX所在的GPIO端口
UART_FIFO_RX6_8); // 接收FIFO为6/8深度（12B）
UARTIntEnable(UART2_BASE, UART_INT_RX | UART_INT_RT); // 使能接收和接收超时中断
unsigned char CopyValue[]= {0xBA,0x04,0x0A,0x04,0x05};
unsigned char ReadULPage5[]= {0xBA,0x03,0x10,0x05};
}
// 通过UART发送字符串
void uartPuts(const char *s)
{
while (*s != '\0')
{
UARTCharPut(UART2_BASE, *s++);
}
}
// 定义接收缓冲区
#define MAX_SIZE 40 // 缓冲区最大限制长度
UARTConfigSet(UART2_BASE, // 配置UART端口
115200, // 波特率：115200
UART_CONFIG_WLEN_8 | // 数据位：8
UART_CONFIG_STOP_ONE | // 停止位：1
UART_CONFIG_PAR_NONE); // 校验位：无