汽车制造业英文专业术语整理
汽车制造专业英语词汇大全
汽车制造专业英语词汇大全Document serial number【KKGB-LBS98YT-BS8CB-BSUT-BST108】汽车专业词汇Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝) fixture 夹具(治具)pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner partsinspect内部检查thumb screw大头螺丝lbs. inch镑、英寸EMI gasket导电条front plate前板rear plate 后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test ofSPS高源高压测试Voltage switchof SPS电源电压接拉键sheet metalparts 冲件plastic parts塑胶件material checklist物料检查表work cell工作间trolley台车carton纸箱sub-line支线personnelresourcedepartment人力资源部productiondepartment生产部门planningdepartment企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler andstraightener整平机punching machine冲床gripper机械手hydraulicmachine油压机lathe车床planer|'plein|刨床miller铣床grinder磨床linear cutting线切割electricalsparkle电火花welder电焊机staker=revitingmachine铆合机position职务president董事长general manager总经理specialassistantmanager特助factory director厂长departmentdirector部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长groupleader/superviso r组长line supervisor 线长assistant manager助理to move, to carry, to handle 搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection 终检to connect material接料to reversematerial 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unloadmaterial卸料to returnmaterial/stockto退料scraped|'skræpid|报废scrape ..v.刮;削deficientpurchase来料不良manufactureprocedure制程deficientmanufacturingprocedure制程不良oxidation |'ksi'dein|氧化scratch刮伤dents压痕defectiveupsiding down抽芽不良defective tostaking铆合不良feeding is notin place送料不到位stamping-missing漏冲education andtraining教育与训练proposalimprovement提案改善spare parts备件forklift叉车trailer=longvehicle拖板车compound die合模die locker锁模器pressureplate=platepinch压板bolt螺栓administration/general affairsdept总务部automaticscrewdriver电动启子thickness gauge厚薄规power wire电源线buzzle蜂鸣器defectiveproduct label不良标签identifyingsheet list标示单screwdriverholder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulichandjack油压板车pallet栈板glove(s)手套glove(s) withexposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机chain链条槽magnetizer加磁器lamp holder灯架to mop the floor 拖地to clean the floor扫地to clean a table 擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessivedefects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up tostandard不合规格dimension/sizeis a littlebigger尺寸偏大(小)slippedscrewhead/slippery screw head螺丝滑头slippedscrewhead/shippery screw thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oilstains油污inclusion杂质painting peeloff脏污shrinking/shrinkage缩水mixed color杂色poor processing制程不良poor incomingpart事件不良fold of pakagingbelt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposedmetal/bare metal金属裸露lack of painting烤漆不到位safety安全quality品质deliverydeadline交货期cost成本engineering工程enterprise plan= enterpriseexpansionprojects企划QC品管equipment设备classification整理regulation整顿cleanness清扫conservation清洁culture教养qualifiedproducts, up-to-grade products良品defective products, notup-to-grade products不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱mould change 换模mold repair修模packing material 包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines压线to compress,compressing压缩to feed, feeding送料transportation运输(be)qualfied, upto grade合格not up to grade,not qualified不合格material change,stock change材料变更feature change特性变更evaluation评估prepare for,makepreparations for准备parameters参数rotating speed,revolution转速manufacturemanagement制造管理abnormalhandling异常处理production unit生产单位steel plate钢板roll material卷料manufactureprocedure制程operationprocedure作业流程to revise,modify修订to switch overto, switch---tothrow--overswitching over切换engineering,projectdifficulty工程瓶颈automation自动化to stake,staking,reviting铆合add lubricatingoil加润滑油shut height of adie架模高度analog-modedevice类模器argon welding氩焊stamping, press冲压punch press,dieing out press冲床uncoiler &strainghtener整平机feeder送料机rack, shelf,stack料架cylinder油缸conveyer belt输送带transmissionrack输送架inch寸动to continue,cont.连动to grip(material)吸料location lump,locating piece,block stop 定位块reset复位smoothly顺利dent压痕deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取processing, to process加工delivery, to deliver 交货to return delivenry to. registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance =receive验收to notice通知application formfor purchase请购单consume,consumption消耗to fill in填写abrasion磨损reverse angle =chamfer倒角character die字模to collect, togather收集failure, trouble故障statistics统计demand andsupply需求career card履历卡to take apart adie卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away adie plate移走模板easily damagedparts易损件standard parts标准件breaking.(be)broken,(be)cracked断裂to lubricate润滑commonvocabulary fordie engineering模具工程常用词汇die 模具figure file,chart file图档cutting die,blanking die冲裁模progressive die,follow (-on)die连续模compound die复合模punched hole冲孔to cutedges=sidecut=side scrap切边to bending折弯to pull, tostretch拉伸Line streching,line pulling线拉伸engraving, toengrave刻印upsiding downedges翻边to stake铆合designing, todesign设计designmodification设计变化folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, frontboard模板padding block垫块stepping bar垫条upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder 文件夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备work in progressproduct在制品casing =containerazation装箱quantity ofphysicalinvetory secondcount 复盘点数量quantity ofcustoms count会计师盘,点数量the first page第一联filed byaccountingdepartment forreference会计部存查end-user/usingunit(department)使用单位summary of year-end physicalinventory bills年终盘点截止单据汇总表bill name单据名称This sheet andphysicalinventory listwill be sent toaccountingDepartmenttogether (Thoseof NHK will besent tofinancialdepartment)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Applicationstatus recordsof year-endphysicalinventory Listandphysicalinventory card年终盘点卡与清册使用－状况明细表blank and wastesheet NO.空白与作废单号plate电镀mold成型material forengineering moldtesting工程试模材料sample样品incomingmaterial to beinspected进货待验description品名steel/rolledsteel钢材Materialstatistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distributiondepartment分发单位location地点chairman主席subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表work order工令remark备注production control confirmation生产确认approved by核准department部门Stock age analysis sheet 库存货龄分析表on-hand inventory现有库存availablematerial良品可使用obsoletematerial良品已呆滞to be inspectedor reworked待验或重工total合计causedescription原因说明part number/ P/N料号type形态item/group/class类别quality品质notes说明year-endphysicalinventorydifferenceanalysis sheet年终盘点差异分析表physicalinventory盘点数量physical countquantity帐面数量differencequantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finishedproduct半成品packingmaterials包材goodproduct/acceptedgoods/ acceptedparts/good parts良品defectiveproduct/non-goodparts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare partsphysicalinventory list备品盘点清单spare moldslocation模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for thepunch head挂钩槽slug hole废料孔expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut 火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button 圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板groove punch压线冲子air-cushion eject-rod气垫顶杆spring-boxeject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speedtransmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号defectiveproducts不良品finishedproducts成品disposedproducts处理品barcode条码flow chart流程表单assembly组装molding成型spareparts=buffer备品coordinate座标dismantle thedie折模auxiliaryfuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derustingmachine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器nick缺口shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=gr ain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差production tempo 生产进度现状torque扭矩spline=themultiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten highspeed steel钨高速的moly high speedsteel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号)shearing剪断tick-marknearside正面压印tick-markfarside反面压印冲压名称类extension dwg展开图procedure dwg工程图material材质materialthickness料片厚度factor系数upward向上downward向下pressspecification冲床规格burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guidingpost内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin 浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板upper plate上模板lower plate下模板die pad下垫板die holder下夹板bottom block下垫脚bottom plate下托板(底板)stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shapepunch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting blockfor location定位支承块air cushionplate气垫板air-cushioneject-rod气垫顶杆trimming punch切边冲子stiffening ribpunch = stinger加强筋冲子ribbon punch压筋冲子reel-stretchpunch卷圆压平冲子guide plate定位板sliding block滑块sliding dowelblock滑块固定块active plate活动板lower slidingplate下滑块板upper holderblock上压块upper mid plate上中间板spring box弹簧箱spring-boxeject-rod弹簧箱顶杆spring-boxeject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sionmolding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulationmolding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=~w=L=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripperplate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=~diaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ~Runner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣品质人员名称类QC qualitycontrol 品质管理人员FQC final quality control 终点品质管制人员IPQC in process quality control 制程中的品质管制人员OQC output quality control 最终出货品质管制人员IQC incoming quality control 进料品质管制人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 品质工程人员品质保证类FAI firstarticleinspection 新品首件检查TVR toolverificationreport 模具确认报告3B 3B 模具正式投产前确认CP capabilityindex 能力指数CPK capabilityindex of process模具制程能力参数SSQAstandardizedsupplier quality合格供应商品质评估OOBA out of boxaudit 开箱检查QFD qualityfunctiondeployment 品质机能展开FMEA failuremodeleffectivenessanalysis 失效模式分析8 disciplines8项回复内容FA final audit最後一次稽核CAR correctiveaction request改正行动要求correctiveaction report改正行动报告FQC运作类AQL AcceptableQuality Level运作类允收品质水准S/S Sample size抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ AverageOutput Quality平均出厂品质AOQL AverageOutput QualityLevel 平均出厂品质Q/R/SQuality/Reliability/Service 品质/可靠度服务MIL-STDMilitary-Standard 军用标准S I-S IVSpecial I-Special IV 特殊抽样水准等级P/N Part Number料号L/N Lot Number特采AOD Accept OnDeviation 特采UAI Use As It首件检查报告FPIR FirstPiece InspectionReport 百万分之一SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计品质管制R Range 全距AR Averary Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR Gauge Reproducibility& Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter直径FREQ Frequency频率N Number 样品数其它品质术语类QCC QualityControl Circle品质圈QIT QualityImprovement Team品质改善小组PDCA Plan DoCheck Action 计划执行检查总结ZD Zero Defect零缺点QI QualityImprovement 品质改善QP QualityPolicy 目标方针TQM TotalQualityManagement 全面品质管理MRB MaterialReject Bill 退货单LQL LimitingQuality Level最低品质水准RMA ReturnMaterial Audit退料认可QAN QualityAmelionrateNotice 品质改善活动ADM AbsoluteDimensionMeasuremat 全尺寸测量QT QualityTarget 品质目标7QCTools 7Quality ControllTools 品管七大手法通用之件类ECN EngineeringChange Notes 工程变更通知(供应商)ECO EngineeringChange Order 工程改动要求(客户)PCN ProcessChange Notice工序改动通知PMP ProductManagement Plan生产管制计划SIPSpecification InProcess 制程检验规格SOP 开始生产IS InspectionSpecification成品检验规范PS PackageSpecification包装规范SPECSpecification规格DWG Drawing 图面系统文件类QC QualitySystem 品质系统ES Engineering Standarization 工程标准CGOO China General PCE龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司T TAIWAN 台湾IWSInternational Workman Standard 工艺标准ISOInternational Standard Organization 国际标准化组织GS GeneralSpecification一般规格CMCS C-China M-Manufact C-Compaq S-Stamping Compaq产品在龙华冲压厂制造作业规范CQCA Q-QualityA-AssemblyCompaq产品在龙华组装厂品管作业规范CQCP P-PaintingCompaq产品在龙华烤漆厂品管作业规范部类PMC Production& MaterialControl 生产和物料控制PPC ProductionPlan Control 生产计划控制MC MaterialControl 物料控制ME ManafactureEngineering 制造工程部PE ProjectEngineering 产品工程部A/C AccountantDept 会计部DC DocumentCenter 资料中心QE QualityEngineering 品质工程(部)QA QualityAssurance 品质保证(处)QC QualityControl 品质管制(课)PD ProductDepartment 生产部LAB Labratry实验室IE IndustrialEngineering 工业工程R&D Research &Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid栈板PO PurchasingOrder 采购订单MO ManufactureOrder 生产单D/C Date Code生产日期码ID/CIdentificationCode (供应商)识别码SWR SpecialWork Request 特殊工作需求L/N Lot Number批号P/N Part Number 料号其它OEM 主机厂PCE Personal Computer Enclosure 个人电脑外设PC Personal Computer 个人电脑CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大陆PRC People's Republic ofChina 中国大陆 the United States of America 美国E-MAILElectrical-Mail 电子邮件N/A NotApplicable 不适用QTY Quantity数量VS 以及REV Revision版本JIT Just InTime 零库存/及时供货I/OInput/Output 输入/输出NG Not Good 不行,不合格C=0 Critical=0极严重不允许ESD Electry-static Discharge静电排放5S 希腊语整理,整顿,清扫,清洁,教养ATIN Attention知会CC Carbon Copy副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM AnteMeridian 上午PM PostMeridian 下午CD Compact Disk光碟CD-ROM CompactDisk Read-OnlyMemory 只读光碟FDD Floppy DiskDrive 软碟机HDD Hard DiskDrive 碟碟机REF Reference仅供参考CONN Connector连接器CAV Cavity 模穴CAD ComputerAid Design 计算机辅助设计ASS'Y Assembly装配,组装MAT'S Material材料IC IntegratedCircuit 集成电路T/P TruePosition 真位度TYP Type 类型WDR WeeklyDeliveryRequitement 周出货需求CT Cycle Time制程周期L/T Lead Time前置时间(生产前准备时间)S/T StandardTime 标准时间P/M ProductMarket 产品市场3CComputer,Commumcation,Consumerelectronic's 消费性电子5WIHWhen,Where,Who,What,Why,How to5MMan,Machine,Material,Method,Measurement4MIHMan,Materia,Money,Method,Time 人力,物力,财务,技术,时间(资源) SQA Strategy Quality Assurance 策略品质保证DQA Desigh Quality Assurance 设计品质保证MQA Manufacture Quality Assurance 制造品质保证SSQA Sales and service Quality Assurance 销售及服务品质保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic Magnetion Inspect 高磁测试FMI Frequency Modulatim Inspect 高频测试B/MBoar/Molding(flat cable)C/P Connectorof PCA/P AssemblySPS Switchingpower supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower立式(机箱)DVD DigitalVedio DiskVCD VdeioCompact DiskLCD LiquidCrystal DisplayCAD ComputerAID DesignCAM ComputerAIDManufacturingCAE ComputerAID EngineeringABIOS AchancedBasic input/outputsystem 先进的基本输入/输出系统CMOSComplemeruaryMetoll OxideSemiconductor互补金属氧化物半导体PDA PersonalDigitalAssistant 个人数字助理IC IntegratedCircuit 集成电路ISA IndustryStandardArchitecture 工业标准体制结构MCA MicroChannelArchitecture微通道结构EISA ExtendedIndustryStandardArchitecture 扩充的工业标准结构SIMM Single in-line memorymodule 单项导通汇流组件DIMM Dual in-line MemoryModule 双项导通汇流组件LED Light-Emitting Diode发光二级管FMEA FailureModeEffectivenes 失效模式分析W/H WireHarness 金属线绪束集组件F/C Flat Calle排线PCB PrintedCircuit Board印刷电路板CAR CorrectionAction Report改善报告NG Not Good 不良WPR WeeklyDeliveryRequirement 周出货要求PPM Parts Per Million 百万分之一TPM Total Production Maintenance 全面生产保养MRP Material Requiremcnt Planning 物料需计划OC Operation System 作业系统TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProceduneEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC MaximumMaterialConditionMMS MaximumMaterial SizeLMC LeastMaterialConditionLMS LeastMaterial Size模具技术用语各种模具常用成形方式accurate diecasting 精密压铸powder forming粉末成形calendaringmolding 压延成形powder metalforging 粉末锻造cold chamber diecasting 冷式压铸precisionforging 精密锻造cold forging 冷锻 press forging冲锻compactingmolding 粉末压出成形 rocking dieforging 摇动锻造compound molding复合成形 rotaryforging 回转锻造compressionmolding 压缩成形rotationalmolding 离心成形dip mold 浸渍成形rubber molding橡胶成形encapsulationmolding 注入成形sand moldcasting 砂模铸造extrusionmolding 挤出成形shell casting 壳模铸造foam forming 泡成形sinter forging烧结锻造forging roll 轧锻six sidesforging 六面锻造gravity casting重力铸造slush molding 凝塑成形hollow(blow)molding 中空(吹出)成形squeeze casting高压铸造hot chamber diecasting 热室压铸swaging 挤锻hot forging 热锻transfer molding转送成形injectionmolding 射出成形warm forging 温锻investmentcasting 精密铸造matched diemethod 对模成形法laminatingmethod 被覆淋膜成形 lowpressure casting低压铸造lost wax casting 脱蜡铸造 matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模 landed plunger mold 有肩柱塞式模具shoe mold 料套式模具center-gated mold 中心浇口式模具 loosedetail mold 活零件模具chill mold 冷硬用铸模 loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模 modularmold 组合式模具double stackmold 双层模具multi-cavitymold 多模穴模具electroformedmold 电铸成形模multi-gate mold复式浇口模具expander die 扩径模offswt bendingdie 双折冷弯模具family mold 反套制品模具plaster mold 石膏模porous mold 通气性模具duplicatedcavity plate 复板模 positivemold 全压式模具flash mold 溢料式模具progressive die顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold热流道模具prototype mold雏形试验模具ingot mold 钢锭模punching die 落料模raising(embossing) 压花起伏成形re-entrant mold倒角式模具runlessinjection mold无流道冷料模具sectional die 对合模具segment mold 组合模 semi-positive mold 半全压式模具shaper 定型模套single cavitymold 单腔模具split mold 双并式模具 spruelessmold 无注道残料模具sweeping mold 平刮铸模 swing die振动模具three platesmold 三片式模具trimming die 切边模unit mold 单元式模具 universalmold 通用模具unscrewing mold退扣式模具 yoketype die 轭型模模具厂常用之标准零配件air vent valve通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁) cavity retainer plate 模穴托板center pin 中心梢clamping block锁定块coil spring 螺旋弹簧cold punched nut冷冲螺母cooling spiral螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate盘形浇口die approach 模头料道die bed 型底direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆 drivebearing 传动轴承ejection pad 顶出衬垫 ejector脱模器ejector guidepin 顶出导梢ejector leaderbusher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machinedplate 角形模板finish machinedround plate 圆形模板fixed bolsterplate 固定侧模板flanged pin 带凸缘flash gate 毛边形浇口flask 上箱floating punch浮动冲头gate 浇口gate land 浇口面goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶冲头headless punch直柄冲头heavily taperedsolid 整体模蕊盒。
汽车行业专用英语词汇及常用缩写
专业英语词汇之DFL专用缩略英语词汇汽车行业常用缩写AAR: Appearance Approval Report 外观批准报告A/D/V: Analysis/Development/Validation 分析/开发/验证A/D/V-DV：ADV Design Validation ADV设计验证A/D/V P&R: Analysis/Development/Validation Plan and Report. This form is used to summarize the plan and results for validation testing. Additional information can be found in the GP-11 procedure. 分析/开发/验证计划和报告A/D/V-PV: ADV Product Validation ADV 产品验证AIAG: Automotive Industries Action Group, an organization formed by General Motors, Ford and Daimler-Chrysler to develop common standards and expectations for automotive suppliers.汽车工业行动集团AP: Advance Purchasing 先期采购APQP: Advanced Product Quality Planning 产品质量先期策划APQP Project Plan: A one-page summary of the SGM APQP process that describes the tasks and the timeframein which they occur. APQP 项目策划AQC: Attribute Quality Characteristic 属性质量特性ASQE: Advanced Supplier Quality Engineer 先期供应商质量工程师BIW: Body in White. Usually the bare metal shell of the body including doors and deck lid prior to paint and trim. 白车身BOM: Bill of Materials 材料清单BOP: Bill of Process 过程清单Brownfield Site: An expansion of an existing facility. 扩建场地CMM: Coordinate Measuring Machine 三坐标测试仪Cpk: Capability Index for a stabile process 过程能力指数CTC: Component Timing Chart (DRE document)零部件时间表(DRE 文件)CTS: Component Technical Specifications 零部件技术规CVER: Concept Vehicle Engineering Release 概念车工程发布DC: Design Complete 设计完成Defect outflow detection: A phrase used in the Supplier Quality Statement of Requirements that refers to in-process or subsequent inspection used to detect defects in parts. 缺陷检测DFM/DFA: Design for Manufacturability / Design for Assembly 可制造性/可装配性设计DFMEA: Design Failure Modes and Effects Analysis. It is used to identify the potential failure modes of a part, associated with the design, and establish a priority system for design improvements.设计失效模式和后果分析DPV: Defects per vehicle 每辆车缺陷数DR: Documentation Required DR特性DRE: Design Release Engineer 设计释放工程师DV: Design Validation 设计验证E&APSP: Engineering & Advance Purchasing Sourcing Process. 工程&先期采购定点程序EP: E-Procurement 电子采购流程Error Occurrence Prevention: A phrase used in the Supplier Quality Statement of Requirements that refers to poke yoke or error-proofing devices used to prevent errors in the manufacturing process from occurring. 防错FTQ: First Time Quality 一次通过质量GA: General Assembly 总装GD&T: Geometric Dimensioning & Tolerancing 几何尺寸与公差SGM: Shanghai General Motors 通用汽车GMAP: General Motors Asian Pacific 通用汽车亚太GME: General Motors Europe 通用汽车欧洲GMNA: General Motors North American 通用汽车北美GP: General Procedure 通用程序GPDS: Global Product Description System 全球产品描述系统GPS: Global Purchasing System 全球采购系统GPSC: Global Purchasing & Supplier Chain 全球采购及供应链GR&R: Gage Repeatability and Reproducibility 检具重复性及再现性Greenfield Site: A new supplier facility that is built to support a program.GVDP: Global Vehicle Development Process 全球整车开发流程IPTV: Incidents per Thousand Vehicles 每千辆车故障IVER: Integration Vehicle Engineering Release 集成车工程发布KCC: Key Control Characteristics. It is a process characteristic where variation can affect the final partand/or the performance of the part. 关键控制特性KCDS: Key Characteristic Designation System 关键特性指示系统Kick-Off Meeting: The first APQP supplier program review.启动会议（第一次APQP 供应商项目评审）KPC: Key Product Characteristic. It is a product characteristic for which reasonably anticipated variation could significantly affect safety, compliance to governmental regulations, or customer satisfaction.关键产品特性LAAM: (General Motors) Latin American, Africa & Meddle East (通用汽车)拉丁美洲、非洲及中东LCR: Lean Opacity Rate. It is the GM daily capacity requirement.正常生产能力MCR: Maximum Capacity Rate. It is the GM maximum capacity requirement. 最大生产能力MOP: Make or Purchase 制造/采购MPC: Material Production Control 物料生产控制MPCE: Material Production Control Europe 欧洲物料生产控制MRD: Material Required Date; date material must be delivered in order to allow a build event to begin. 物料需求日期MSA: Measurement Systems Analysis 测量系统分析MVBns: Manufacturing Validation Build non-saleable 非销售车制造验证MVBs: Manufacturing Validation Build saleable 销售车制造验证NBH: New Business Hold 停止新业务N.O.D.: Notice of Decision 决议通知OEM: Original Equipment Manufacturer 主机客户PAD: Production Assembly Documents 生产装配文件PC&L: Production Control & Logistics 生产控制&物流PDT: Product Development Team 产品开发小组PFMEA: Process Failure Modes and Effects Analysis. It is used to identify potential failure modes associated with the manufacturing and assembly process.过程失效模式和后果分析PPAP: Production Part Approval Process 生产件批准程序Ppk: Performance index for a stable process 过程能力指数PPM: 1) Program Purchasing Manager, 2) Parts per Million (rejects and returns to suppliers) 1)项目经理2) 每百万件的产品缺陷数PPV: Product & Process Validation 产品及过程验证PQC: Product Quality Characteristic 产品质量特性PR/R: Problem Reporting & Resolution 问题报告及解决PSA: Potential Supplier Assessment, a subset of the Quality System Assessment (QSA)潜在供应商评审PV: Product Validation 产品验证QSA: Quality System Assessment 质量体系评审QSB: Quality Systems Basics 质量体系基础QTC: Quoted Tool Capacity 工装报价能力RASIC: Responsible, Approve, Support, Inform, Consult 负责、批准、支持、通知、讨论RR: Run at Rate按节拍生产RFQ: Request For Quotation 报价要求RPN: Risk Priority Number related to FMEA development 风险顺序数RPN Reduction Plan: An action plan that describes what is being done to reduce the risk priority number for items listed in the DFMEA or PFMEA.降低RPN 值计划SDE: Supplier Development Engineer 供应商开发工程师SFMEA: System Failure Mode and Effects Analysis 系统失效模式分析SMT: System Management Team 系统管理小组SOA: Start of Acceleration 加速开始SORP: Start of Regular Production 正式生产SOR: Statement of Requirements 要求声明SPC: Statistical Process Control 统计过程控制SPO: (General Motors) Service and Parts Operations (通用汽车)零件与服务分部SQ: Supplier Quality 供应商质量SQE: Supplier Quality Engineer 供应商质量工程师SQIP: Supplier Quality Improvement Process 供应商质量改进过程SSF: Start of System Fill 系统填充开始SSTS: Sub-system Technical Specifications 子系统技术规Sub-Assembly / Sub-System: An assembly of sub-components delivered to the SGM main production line for installation to the vehicle as a single unit.Subcontractor: The supplier of a sub-component to a Complex System/Subassembly supplier (Tier 2, 3, etc). 分供方SVE: Sub-System Validation Engineer 子系统验证工程师SVER: Structure Vehicle Engineering Release.结构车工程发布Team Feasibility Commitment: An AIAG APQP form that is provided with the Request for Quotation. It isthe supplier’s concerns with the feasibility of manufacturing the part as specified. 小组可行性承诺TKO: Tooling Kick-Off 模具启动会议UG: Unigraphics UG工程绘图造型系统VLE: Vehicle Line Executive 车辆平台负责人VTC: Validation Testing Complete 验证试验完成EWO: Engineering Work Order 工程工作指令。
最全汽车行业术语英文翻译
最全汽车行业术语英文翻译1. 汽车类型- Sedan: 轿车- Hatchback: 掀背车- SUV (Sport Utility Vehicle): 运动型多功能车- MPV (Multi-Purpose Vehicle): 多功能车- Coupe: 轿跑车- Convertible: 敞篷车- Pickup: 皮卡车- Van: 面包车- Electric Vehicle (EV): 电动汽车- Hybrid Vehicle: 混合动力汽车2. 发动机和动力系统- Engine: 发动机- Horsepower (HP): 马力- Torque: 扭矩- Fuel Injection: 燃油喷射- Turbocharger: 涡轮增压器- Supercharger: 机械增压器- Cylinder: 气缸- Transmission: 变速器- Manual Transmission: 手动变速器- Automatic Transmission: 自动变速器- Continuously Variable Transmission (CVT): 连续变速器- Four-Wheel Drive (4WD): 四轮驱动- All-Wheel Drive (AWD): 全轮驱动- Electric Motor: 电动机- Battery Pack: 电池组3. 车身部件- Chassis: 底盘- Bodywork: 车身- Hood: 发动机盖- Trunk: 后备箱- Bumper: 保险杠- Fender: 车翼- Door: 车门- Windshield: 前挡风玻璃- Roof: 车顶- Spoiler: 尾翼- Headlights: 前灯- Taillights: 尾灯4. 汽车零部件- Brakes: 制动器- Suspension: 悬挂系统- Steering Wheel: 方向盘- Tires: 轮胎- Exhaust System: 排气系统- Air Conditioning: 空调系统- Radiator: 散热器- Battery: 电池- Alternator: 发电机- Starter Motor: 起动机- Fuel Pump: 燃油泵- Ignition System: 点火系统5. 汽车性能指标- Acceleration: 加速度- Top Speed: 极速- 0-60 mph Time: 0-96公里/小时加速时间- Fuel Efficiency: 燃油效率- Range: 续航里程- Curb Weight: 空载重量- Gross Vehicle Weight (GVW): 总重量- Wheelbase: 轴距6. 安全设备- Seatbelt: 安全带- Airbags: 气囊- Anti-lock Braking System (ABS): 防抱死制动系统- Electronic Stability Control (ESC): 电子稳定控制系统- Tire Pressure Monitoring System (TPMS): 轮胎气压监测系统- Adaptive Cruise Control: 自适应巡航控制- Blind Spot Detection: 盲点监测以上是最全汽车行业术语的英文翻译，希望能对您有所帮助！。
汽车制造业英文专业术语汇总
序号
1 2 3 4
术
3G 3M 5M AAR
语
5
Action plan
6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
ADV ADV–DV A/D/V P&R ADV–PV AEM AIAG Andon AP APQP APO AS ASQE ATT Audit Bidlist
68
GP-4
69 70
GP-5 GP-6
71
GP-7
72 73
GP-8 GP-9
74
GP-10
75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91
GP-11 GP-12 GPDS GPS GQTS GR&R GVDP HR IPTV I-Chart I.E. IOM IOS IRR I.T. JES JIT
SPQRC SQ SQA SQC SQE SQIP SSF SSTS S.T.E.P TBD
192
Tier 1 Supplier
193 194 195 196 197 198 199 200 201 202
Tier 2 Supplier TA TOC TPM TQC TQM TR TT UG VDP
132
PDCA
133 134 135 136
PDT PFMEA PFEP Pilot
137 138 139 140 141
PM PMP PO Poke Yoke PPAP
142
PPM
143 144 145 146 147 148 149 150 151
汽车制造专业英语词汇大全【范本模板】
汽车专业词汇Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧（螺丝)fixture 夹具(治具)pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs。
inch镑、英寸EMI gasket导电条front plate前板rear plate 后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi—pot test of SPS高源高压测试Voltage switch of SPS电源电压接拉键sheet metal parts 冲件plastic parts塑胶件material check list物料检查表work cell工作间trolley台车carton纸箱sub—line支线personnel resource department人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床gripper机械手hydraulic machine油压机lathe车床planer ｜'plein＆＃61611;｜刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager ｜=vice manager副理section supervisor课长deputy section supervisor =vicesection superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry，to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped ｜'skr＆aelig；pid｜报废scrape 。
汽车制造专业英语词汇大全(4000词条)
汽车专业词汇Assembly line组装线Layout布置图(Would you please take e to/Can I see the layout of the assembly line?)Rivet gun拉钉枪(Despite their lack of operators and rive tguns,them finished the ork.)Pneumatic screw driver气动起子Electric screw driver 电动起子Torpue spanner 扭力扳手Generally speaking，there is three kinds of tightening tools in automotive industry，they are pneumatic screw driver、torque spanner wrench）worktable 工作桌（the work table is used to help the operator to fit together the abs）fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具) (please makesure if the fixture of the left door isout off shape in body shop)pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查(I thinkwe need modify the technicalstandard of cosmetic inspect if wecan’t slove the dispersion problemof front bumper and fender)inner parts inspect内部检查thumb screw大头螺丝lbs. inch镑、英寸EMI gasket导电条front plate前板rear plate 后板chassis 基座bezel panel面板power button电源按键(if you wantto use the function of thee2cos,please turn on the powerbutton.)reset button重置键(only if you turnon the reset button,you can rebootthe equipment )Hi-pot test of SPS高源高压测试Voltage switch of SPS电源电压接拉键sheet metal parts 冲件plastic parts塑胶件material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线personnel resource department人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床gripper机械手(the gripper forassembling the battery is unusable)hydraulic machine油压机lathe车床planer |'plein|刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务(from a general perspective，get high position and salary，they can buy a house，a car，get married，child.)president董事长(our president is easy going and intelligent in Beijing changan automotive campany)general manager总经理(real leader have the respect of their peers andtheir teams ,and they treat one as equals in terms of the amount of the respect they are due,from the lowliest assistant to the general manager)factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装final inspection终检to connect material接料to reverse material 翻料cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skræpid|报废scrape ..v.刮;削deficient purchase来料不良(Deficient purchase caused theproblem)manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dein|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良feeding is not in place送料不到位stamping-missing漏冲education and training教育与训练proposal improvement提案改善spare parts备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓(the torque should bedecided in ters of the strenthstandred of the bolts)administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车pallet栈板glove(s)手套glove(s) with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机chain链条槽magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小)slipped screwhead/slippery screwhead螺丝滑头slipped screwhead/shippery screwthread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位safety安全quality品质delivery deadline交货期cost成本engineering工程enterprise plan = enterpriseexpansion projects企划QC品管equipment设备classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products, up-to-gradeproducts良品defective products, not up-to-gradeproducts不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱mould change 换模mold repair修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate;barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cutmaterial, to input落料to impose lines压线to compress, compressing压缩to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, not qualified不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for 准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify修订to switch over to, switch---to throw--over switching over切换engineering, project difficulty 工程瓶颈automation自动化to stake, staking, reviting铆合add lubricating oil加润滑油shut height of a die架模高度analog-mode device类模器argon welding氩焊stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸conveyer belt输送带transmission rack输送架inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, blockstop 定位块reset复位smoothly顺利dent压痕deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取processing, to process加工delivery, to deliver 交货to return delivenry to.registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked断裂to lubricate润滑common vocabulary for dieengineering模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die连续模compound die复合模punched hole冲孔to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder文件夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备work in progress product在制品casing = containerazation装箱quantity of physical invetory secondcount 复盘点数量quantity of customs count会计师盘,点数量the first page第一联filed by accounting department forreference会计部存查end-user/using unit(department)使用单位summary of year-end physicalinventory bills年终盘点截止单据汇总表bill name单据名称This sheet and physical inventorylist will be sent to accountingDepartment together (Those ofNHK will be sent to financialdepartment)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application status records ofyear-end physical inventory List andphysical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering moldtesting工程试模材料sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材Material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by /prepared by核准/审核/承办PCE assembly production schedulesheetPCE组装厂生产排配表work order工令remark备注production control confirmation生产确认approved by核准department部门Stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质notes说明year-end physical inventorydifference analysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器nick缺口shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号)shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板upper plate上模板lower plate下模板die pad下垫板die holder下夹板bottom block下垫脚bottom plate下托板(底板)stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣品质人员名称类QC quality control 品质管理人员FQC final quality control 终点品质管制人员IPQC in process quality control 制程中的品质管制人员OQC output quality control 最终出货品质管制人员IQC incoming quality control 进料品质管制人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance出货质量保证人员QE quality engineering 品质工程人员品质保证类FAI first article inspection 新品首件检查TVR tool verification report 模具确认报告3B 3B 模具正式投产前确认CP capability index 能力指数CPK capability index of process模具制程能力参数SSQA standardized supplierquality 合格供应商品质评估OOBA out of box audit 开箱检查QFD quality function deployment品质机能展开FMEA failure model effectivenessanalysis 失效模式分析8 disciplines 8项回复内容FA final audit 最後一次稽核CAR corrective action request改正行动要求corrective action report 改正行动报告FQC运作类AQL Acceptable Quality Level运作类允收品质水准S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ Average Output Quality 平均出厂品质AOQL Average Output QualityLevel 平均出厂品质Q/R/S Quality/Reliability/Service品质/可靠度服务MIL-STD Military-Standard 军用标准S I-S IV Special I-Special IV 特殊抽样水准等级P/N Part Number 料号L/N Lot Number 特采AOD Accept On Deviation 特采UAI Use As It 首件检查报告FPIR First Piece InspectionReport 百万分之一SPC Statistical Process Control统计制程管制SQC Statistical Quality Control统计品质管制R Range 全距AR Averary Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR Gauge Reproducibility&Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它品质术语类QCC Quality Control Circle 品质圈QIT Quality Improvement Team 品质改善小组PDCA Plan Do Check Action 计划执行检查总结ZD Zero Defect 零缺点QI Quality Improvement 品质改善QP Quality Policy 目标方针TQM Total Quality Management全面品质管理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低品质水准RMA Return Material Audit 退料认可QAN Quality Amelionrate Notice品质改善活动ADM Absolute DimensionMeasuremat 全尺寸测量QT Quality Target 品质目标7QCT ools 7 Quality Controll Tools品管七大手法通用之件类ECN Engineering Change Notes工程变更通知(供应商)ECO Engineering Change Order工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan生产管制计划SIP Specification In Process 制程检验规格SOP 开始生产IS Inspection Specification 成品检验规范PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QC Quality System 品质系统ES Engineering Standarization工程标准CGOO China General PCE龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司T TAIWAN 台湾IWS International WorkmanStandard 工艺标准ISO International StandardOrganization 国际标准化组织GS General Specification 一般规格CMCS C-China M-ManufactC-Compaq S-Stamping Compaq产品在龙华冲压厂制造作业规范CQCA Q-Quality A-AssemblyCompaq产品在龙华组装厂品管作业规范CQCP P-Painting Compaq产品在龙华烤漆厂品管作业规范部类PMC Production & MaterialControl 生产和物料控制PPC Production Plan Control 生产计划控制MC Material Control 物料控制ME Manafacture Engineering 制造工程部PE Project Engineering 产品工程部A/C Accountant Dept 会计部DC Document Center 资料中心QE Quality Engineering 品质工程(部)QA Quality Assurance 品质保证(处)QC Quality Control 品质管制(课) PD Product Department 生产部LAB Labratry 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂) S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供应商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号其它OEM 主机厂PCE Personal ComputerEnclosure 个人电脑外设PC Personal Computer 个人电脑CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大陆PRC People's Republic of China中国大陆U.S.A the United States ofAmerica 美国A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存/及时供货I/O Input/Output 输入/输出NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electry-static Discharge 静电排放5S 希腊语整理,整顿,清扫,清洁,教养ATIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光碟CD-ROM Compact DiskRead-Only Memory 只读光碟FDD Floppy Disk Drive 软碟机HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CAV Cavity 模穴CAD Computer Aid Design 计算机辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly Delivery Requitement 周出货需求C?T Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间)S/T Standard Time 标准时间P/M Product Market 产品市场3CComputer,Commumcation,Consumer electronic's 消费性电子5WIHWhen,Where,Who,What,Why,Howto5MMan,Machine,Material,Method,Mea surement4MIHMan,Materia,Money,Method,Time人力,物力,财务,技术,时间(资源) SQA Strategy Quality Assurance策略品质保证DQA Desigh Quality Assurance设计品质保证MQA Manufacture QualityAssurance 制造品质保证SSQA Sales and service QualityAssurance 销售及服务品质保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic Magnetion Inspect高磁测试FMI Frequency Modulatim Inspect高频测试B/M Boar/Molding(flat cable)C/P Connector of PCA/P AssemblySPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Vedio DiskVCD Vdeio Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AIDManufacturingCAE Computer AID EngineeringABIOS Achanced Basic input/output system 先进的基本输入/输出系统CMOS Complemeruary MetollOxide Semiconductor 互补金属氧化物半导体PDA Personal Digital Assistant个人数字助理IC Integrated Circuit 集成电路ISA Industry StandardArchitecture 工业标准体制结构MCA Micro Channel Architecture微通道结构EISA Extended Industry StandardArchitecture 扩充的工业标准结构SIMM Single in-line memorymodule 单项导通汇流组件DIMM Dual in-line MemoryModule 双项导通汇流组件LED Light-Emitting Diode 发光二级管FMEA Failure Mode Effectivenes失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Calle 排线PCB Printed Circuit Board 印刷电路板CAR Correction Action Report改善报告NG Not Good 不良WPR Weekly DeliveryRequirement 周出货要求PPM Parts Per Million 百万分之一TPM Total ProductionMaintenance 全面生产保养MRP Material RequiremcntPlanning 物料需计划OC Operation System 作业系统TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProceduneEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material Size模具技术用语各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming ?泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matchedmould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landedplunger mold 有肩柱塞式模具shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold活动式模具clod hobbing 冷挤压制模louveringdie 百叶窗冲切模composite dies 复合模具manifolddie 分歧管模具counter punch 反凸模modularmold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具family mold 反套制品模具plaster mold 石膏模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具split mold 双并式模具sprueless mold 无注道残料模具sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoketype die 轭型模模具厂常用之标准零配件air vent valve 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁)cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drivebearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejectorleader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘?flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶?冲头headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locatingring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套manifold block 歧管档块master plate 靠模样板match plate分型板mold base 塑胶模座mold clamp铸模紧固夹mold platen 模用板moving bolster换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paring line分模线parting lock set 合模定位器passguide 穴型导板peened head punch 镶入式冲头pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin嵌件梢retainer plate 托料板return pin 回位梢riding stripper 浮动脱模器ringgate 环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton骨架slag riser 冒渣口slide(slide core)滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架spindle 主轴sprue 注道sprue bushing 注道衬套spruebushing guide 注道导套sprue lock bushing 注道定位衬套spue line 合模线square key 方键square nut 方螺帽square thread方螺纹stop collar 限位套stop pin 止动梢stop ring 止动环stopper 定位停止梢。
汽车制造专业英语词汇大全
.汽车专业词汇Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch镑、英寸EMI gasket导电条front plate前板rear plate 后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS电源电压接拉键sheet metal parts 冲件plastic parts塑胶件material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线personnel resource department人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床gripper机械手hydraulic machine油压机lathe车床planer |'plein|刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vicesection superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skræpid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure 制程不良oxidation |' ksi'dein|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良feeding is not in place送料不到位stamping-missing漏冲education and training教育与训练proposal improvement提案改善spare parts备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车pallet栈板glove(s)手套glove(s) with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机chain链条槽magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小)slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位safety安全quality品质delivery deadline交货期cost成本engineering工程enterprise plan = enterpriseexpansion projects企划QC品管equipment设备classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products, up-to-gradeproducts良品defective products, not up-to-gradeproducts不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱mould change 换模mold repair修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate;barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cutmaterial, to input落料to impose lines压线to compress, compressing压缩to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, not qualified不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify修订to switch over to, switch---to throw--over switching over切换engineering, project difficulty工程瓶颈automation自动化to stake, staking, reviting铆合add lubricating oil加润滑油shut height of a die架模高度analog-mode device类模器argon welding氩焊stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸conveyer belt输送带transmission rack输送架inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, blockstop 定位块reset复位smoothly顺利dent压痕deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取processing, to process加工delivery, to deliver 交货to return delivenry to.registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked断裂to lubricate润滑common vocabulary for dieengineering模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die连续模compound die复合模punched hole冲孔to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder文件夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备work in progress product在制品casing = containerazation装箱quantity of physical invetory secondcount 复盘点数量quantity of customs count会计师盘,点数量the first page第一联filed by accounting department forreference会计部存查end-user/using unit(department)使用单位summary of year-end physicalinventory bills年终盘点截止单据汇总表bill name单据名称This sheet and physical inventorylist will be sent to accountingDepartment together (Those ofNHK will be sent to financialdepartment)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application status records ofyear-end physical inventory List andphysical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering moldtesting工程试模材料sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材Material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheetPCE组装厂生产排配表work order工令remark备注production control confirmation生产确认approved by核准department部门Stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质notes说明year-end physical inventorydifference analysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器nick缺口shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号)shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板upper plate上模板lower plate下模板die pad下垫板die holder下夹板bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣品质人员名称类QC quality control 品质管理人员FQC final quality control 终点品质管制人员IPQC in process quality control制程中的品质管制人员OQC output quality control 最终出货品质管制人员IQC incoming quality control 进料品质管制人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance出货质量保证人员QE quality engineering 品质工程人员品质保证类FAI first article inspection 新品首件检查TVR tool verification report 模具确认报告3B 3B 模具正式投产前确认CP capability index 能力指数CPK capability index of process 模具制程能力参数SSQA standardized supplier quality 合格供应商品质评估OOBA out of box audit 开箱检查QFD quality function deployment 品质机能展开FMEA failure model effectiveness analysis 失效模式分析8 disciplines 8项回复内容FA final audit 最後一次稽核CAR corrective action request 改正行动要求corrective action report 改正行动报告FQC运作类AQL Acceptable Quality Level 运作类允收品质水准S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ Average Output Quality 平均出厂品质AOQL Average Output QualityLevel 平均出厂品质Q/R/S Quality/Reliability/Service品质/可靠度服务MIL-STD Military-Standard 军用标准S I-S IV Special I-Special IV 特殊抽样水准等级P/N Part Number 料号L/N Lot Number 特采AOD Accept On Deviation 特采UAI Use As It 首件检查报告FPIR First Piece InspectionReport 百万分之一SPC Statistical Process Control统计制程管制SQC Statistical Quality Control统计品质管制R Range 全距AR Averary Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR GaugeReproducibility&Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它品质术语类QCC Quality Control Circle 品质圈QIT Quality Improvement Team品质改善小组PDCA Plan Do Check Action 计划执行检查总结ZD Zero Defect 零缺点QI Quality Improvement 品质改善QP Quality Policy 目标方针TQM Total Quality Management全面品质管理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低品质水准RMA Return Material Audit 退料认可QAN Quality Amelionrate Notice品质改善活动ADM Absolute Dimension Measuremat 全尺寸测量QT Quality Target 品质目标7QCT ools 7 Quality Controll Tools 品管七大手法通用之件类ECN Engineering Change Notes 工程变更通知(供应商)ECO Engineering Change Order 工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Specification In Process 制程检验规格SOP 开始生产IS Inspection Specification 成品检验规范PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QC Quality System 品质系统ES Engineering Standarization工程标准CGOO China General PCE龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司T TAIWAN 台湾IWS International WorkmanStandard 工艺标准ISO International StandardOrganization 国际标准化组织GS General Specification 一般规格CMCS C-China M-ManufactC-Compaq S-Stamping Compaq产品在龙华冲压厂制造作业规范CQCA Q-Quality A-AssemblyCompaq产品在龙华组装厂品管作业规范CQCP P-Painting Compaq产品在龙华烤漆厂品管作业规范部类PMC Production & MaterialControl 生产和物料控制PPC Production Plan Control 生产计划控制MC Material Control 物料控制ME Manafacture Engineering 制造工程部PE Project Engineering 产品工程部A/C Accountant Dept 会计部DC Document Center 资料中心QE Quality Engineering 品质工程(部)QA Quality Assurance 品质保证(处)QC Quality Control 品质管制(课)PD Product Department 生产部LAB Labratry 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供应商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号其它OEM 主机厂PCE Personal Computer Enclosure 个人电脑外设PC Personal Computer 个人电脑CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大陆PRC People's Republic of China中国大陆U.S.A the United States ofAmerica 美国A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存/及时供货I/O Input/Output 输入/输出NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electry-static Discharge 静电排放5S 希腊语整理,整顿,清扫,清洁,教养ATIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光碟CD-ROM Compact DiskRead-Only Memory 只读光碟FDD Floppy Disk Drive 软碟机HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CAV Cavity 模穴CAD Computer Aid Design 计算机辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly DeliveryRequitement 周出货需求C?T Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间)S/T Standard Time 标准时间P/M Product Market 产品市场3CComputer,Commumcation,Consumer electronic's 消费性电子5WIHWhen,Where,Who,What,Why,Howto5MMan,Machine,Material,Method,Mea surement4MIHMan,Materia,Money,Method,Time 人力,物力,财务,技术,时间(资源) SQA Strategy Quality Assurance 策略品质保证DQA Desigh Quality Assurance 设计品质保证MQA Manufacture Quality Assurance 制造品质保证SSQA Sales and service Quality Assurance 销售及服务品质保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic Magnetion Inspect 高磁测试FMI Frequency Modulatim Inspect 高频测试B/M Boar/Molding(flat cable) C/P Connector of PCA/P AssemblySPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Vedio DiskVCD Vdeio Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AIDManufacturingCAE Computer AID EngineeringABIOS Achanced Basic input/output system 先进的基本输入/输出系统CMOS Complemeruary MetollOxide Semiconductor 互补金属氧化物半导体PDA Personal Digital Assistant个人数字助理IC Integrated Circuit 集成电路ISA Industry StandardArchitecture 工业标准体制结构MCA Micro Channel Architecture微通道结构EISA Extended Industry StandardArchitecture 扩充的工业标准结构SIMM Single in-line memorymodule 单项导通汇流组件DIMM Dual in-line MemoryModule 双项导通汇流组件LED Light-Emitting Diode 发光二级管FMEA Failure Mode Effectivenes失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Calle 排线PCB Printed Circuit Board 印刷电路板CAR Correction Action Report改善报告NG Not Good 不良WPR Weekly DeliveryRequirement 周出货要求PPM Parts Per Million 百万分之一TPM Total ProductionMaintenance 全面生产保养MRP Material RequiremcntPlanning 物料需计划OC Operation System 作业系统TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProceduneEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material Size LMC Least Material Condition LMS Least Material Size模具技术用语各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming ?泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matchedmould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landedplunger mold 有肩柱塞式模具shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold活动式模具clod hobbing 冷挤压制模louveringdie 百叶窗冲切模composite dies 复合模具manifolddie 分歧管模具counter punch 反凸模modularmold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具family mold 反套制品模具plaster mold 石膏模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具split mold 双并式模具sprueless mold 无注道残料模具sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoketype die 轭型模模具厂常用之标准零配件air vent valve 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁)cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drivebearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejectorleader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘?flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶?冲头headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locatingring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套manifold block 歧管档块master plate 靠模样板match plate分型板mold base 塑胶模座mold clamp铸模紧固夹mold platen 模用板moving bolster换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paring line分模线parting lock set 合模定位器passguide 穴型导板peened head punch 镶入式冲头pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin嵌件梢retainer plate 托料板return pin 回位梢riding stripper 浮动脱模器ringgate 环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton骨架slag riser 冒渣口slide(slide core)滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架spindle 主轴sprue 注道sprue bushing 注道衬套sprue bushing guide 注道导套sprue lock bushing 注道定位衬套spue line 合模线square key 方键square nut 方螺帽square thread 方螺纹stop collar 限位套stop pin 止动梢stop ring 止动环stopper 定位停止梢straight pin 圆柱? stripper bolt 脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱support pin 支撑梢supporting plate 托板sweeptemplete 造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝模板模具常用之工作机械3D coordinate measurement 三次元量床boring machine 搪孔机cnc milling machine CNC铣床contouring machine 轮廓锯床copy grinding machine 仿形磨床copy lathe 仿形车床copy milling machine 仿形铣床copy shaping machine 仿形刨床cylindrical grinding machine 外圆磨床die spotting machine 合模机engraving machine 雕刻机engraving E.D.M. 雕模放置加工机form grinding machine 成形磨床graphite machine 石墨加工机horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心internal cylindricalmachine 内圆磨床jig grinding machine 冶具磨床lap machine 研磨机machine center 加工制造中心multi model miller 靠磨铣床NC drilling machine NC钻床NC grinding machine NC磨床NC lathe NC车床NC programming system NC程式制作系统planer 龙门刨床profile grinding machine 投影磨床projection grinder 投影磨床radial drilling machine 旋臂床shaper 牛头刨床surface grinder 平面磨床try machine 试模机turret lathe 转塔车床universal toolgrinding machine 万能工具磨床vertical machine center 立式加工制造中心wire E.D.M. 线割放电加工机检验量测工具用语。
汽车研发与制造专业术语汇总
汽车研发与制造专业术语汇总1. 汽车制造 - Automobile Manufacturing2. 汽车研发 - Automobile Research and Development (R&D)3. 汽车设计 - Automotive Design4. 动力系统 - Powertrain System5. 车身结构 - Vehicle Body Structure6. 底盘系统 - Chassis System7. 混合动力 - Hybrid Power9. 电动机 - Electric Motor10. 能源管理系统 - Energy Management System11. 燃料电池 - Fuel Cell12. 变速器 - Transmission13. 驱动轴 - Drive Shaft14. 刹车系统 - Brake System15. 悬挂系统 - Suspension System16. 转向系统 - Steering System17. 车轮驱动 - Wheel Drive18. 燃油喷射装置 - Fuel Injection System19. 排放控制系统 - Emission Control System20. 汽车安全 - Automotive Safety21. 碰撞安全 - Crash Safety22. 安全气囊 - Airbag23. 动力输出 - Power Output24. 引擎输出功率 - Engine Output Power25. 马力 - Horsepower (HP)26. 转速 - Revolutions Per Minute (RPM)27. 发动机转速 - Engine RPM28. 加速度 - Acceleration29. 最高速度 - Top Speed30. 运动性能 - Performance31. 行驶阻力 - Rolling Resistance32. 空气阻力 - Air Resistance33. 高速行驶稳定性 - High Speed Stability34. 转弯半径 - Turning Radius35. 转向灵活性 - Steering Flexibility36. 驱动方式 - Drive Mode37. 前驱 - Front-Wheel Drive (FWD)38. 后驱 - Rear-Wheel Drive (RWD)39. 四驱 - Four-Wheel Drive (4WD)40. 智能驾驶 - Intelligent Driving41. 自动驾驶 - Autonomous Driving42. 感知系统 - Perception System43. 控制系统 - Control System44. 制动系统 - Braking System45. 监测系统 - Monitoring System46. 传感器 - Sensor47. 摄像头 - Camera48. 激光雷达 - Lidar (Light Detection and Ranging)49. 雷达 - Radar50. 超声波 - Ultrasonic51. 航空航天工程 - Aerospace Engineering53. 空气动力学 - Aerodynamics54. 解决方案 - Solution55. 耐久性 - Durability56. 稳定性 - Stability57. 谐波 - Harmonic58. 系统集成 - System Integration59. 系统优化 - System Optimization60. 设备现场验证 - Equipment On-Site Verification61. 审查结果确认 - Confirmation of Review Results62. 控制程序 - Control Program63. 安全性评估 - Safety Assessment64. 安全性论证 - Safety Demonstration65. 故障模式和影响分析 - Fault Mode and Effect Analysis (FMEA)66. 可靠性 - Reliability67. 性能测试 - Performance Testing68. 效能测试 - Efficiency Testing69. 耐久测试 - Durability Testing70. 车辆测试台 - Vehicle Test Bench71. 噪音测试 - Noise Testing72. 振动测试 - Vibration Testing73. 线性加速度 - Linear Acceleration74. 制动距离 - Braking Distance75. 操控性 - Handling76. 稳定性控制系统 - Stability Control System77. 碰撞测试 - Crash Testing78. 正面碰撞 - Frontal Crash79. 侧面碰撞 - Side Impact80. 翻车测试 - Rollover Testing81. 高温测试 - High Temperature Testing82. 低温测试 - Low Temperature Testing83. 湿度测试 - Humidity Testing84. 耐久性验证 - Durability Verification86. 安全标准规范 - Safety Standard Specification87. 环境法规 - Environmental Regulation88. 国际标准组织 - International Standards Organization (ISO)89. 汽车工程师 - Automotive Engineer90. 研发团队 - Research and Development Team91. 制造工艺 - Manufacturing Process92. 产品质量 - Product Quality93. 工艺改进 - Process Improvement94. 成本控制 - Cost Control95. 供应链管理 - Supply Chain Management96. 过程控制 - Process Control97. 产能规划 - Capacity Planning98. 质量控制 - Quality Control99. 供应商评估 - Supplier Evaluation100. 质量管理体系 - Quality Management System这些术语涵盖了汽车研发与制造的各个方面，可以帮助人们更好地理解和参与汽车的设计、研发和制造过程。
汽车制造专业英语词汇大全
汽车专业词汇Aｓsembly line组装线Layout布置图(Wｏuｌｄｙou please take ｅto/CaｎI see the lａｙout of the asｓemｂly line?)Riveｔguｎ拉钉枪(Ｄeｓpite t ｈeｉr lack ofｏｐeratorｓand ｒiｖｅｔguns,them fｉnｉshｅｄthe ork.)Pｎｅumａｔｉc scrｅw dｒiver 气动起子Ｅlectric screw drｉver 电动起子Torpue spanｎer扭力扳手Geｎeralｌy speaking,there is thｒee kiｎds of ｔiｇhteｎing tｏolｓin auｔomoｔｉｖe iｎdｕstry,tｈeｙare ｐｎｅumatic screw driver、torque ｓpａnner w ｒｅnｃh）wｏrｋtable工作桌(thｅworktaｂle is usｅｄto ｈelp tｈe opｅrａtor to ｆit tｏｇetｈer tｈｅabs)fit togeｔher组装在一起fasteｎ锁紧(螺丝)ｆiｘture 夹具(治具) (pｌｅaｓeｍａke ｓuｒe iｆthe fiｘtｕreｏｆthe leｆt dｏoｒis out ｏffｓhape iｎboｄy ｓhop）pallet栈板baｒｃｏde条码barcoｄe scanｎer条码扫描器fuｓe togｅtｈer熔合fuse machine热熔机ｒepair修理operatｏr作业员QＣ品管supervｉsoｒ课长ME制造工程师MT制造生技cosmetic ｉnsｐect外观检查（I tｈink we nｅｅｄｍodｉｆｙtｈe ｔecｈnicaｌｓtandaｒｄｏfcosmｅtiｃinspｅcｔif we can’tslove the dｉspersioｎprｏbｌeｍof fｒonｔbｕmper and fｅnder）ｉnner parｔｓinｓpect内部检查thｕmb screw大头螺丝lbｓ.ｉnch镑、英寸ＥMI gasｋet导电条front ｐｌate前板rｅar plａｔe后板chaｓsiｓ基座bｅzeｌpａｎel面板power buｔton电源按键(if yｏｕwant tｏｕse ｔｈe functionof the e2cｏs,pｌｅase ｔurn ｏn the poweｒbuttoｎ.)reset ｂutton重置键(oｎly ｉｆｙou tｕｒn ｏn ｔhe ｒeｓｅtbuttｏn,yｏu ｃan reｂoｏｔtheｅｑuipment )Ｈi-pot test oｆSPＳ高源高压测试Voltage swiｔｃｈof ＳPS电源电压接拉键shｅｅｔｍｅtａl ｐａrtｓ冲件plasｔiｃparｔs塑胶件ｍａteriaｌｃｈeckｌｉst物料检查表woｒｋcelｌ工作间ｔrolley台车cartoｎ纸箱ｓub-liｎe支线pｅrsonｎｅl resoｕｒce dｅpartmｅｎt人力资源部ｐroduction dｅpaｒtmeｎt生产部门plａｎning depaｒｔmｅｎt企划部ＱC Ｓｅcｔioｎ品管科stａmｐiｎg facｔoｒy冲压厂paintｉｎg faｃtｏrｙ烤漆厂moldｉnｇｆactｏrｙ成型厂comｍon equipment常用设备uncoiler and ｓtrａｉghtener整平机pｕnchｉnｇmachｉne 冲床grｉpper机械手(ｔhe grｉppｅr fo ｒaｓsembling thｅbattｅry is u ｎusａｂle)ｈydraulic mａcｈine油压机ｌatｈe车床planer ｜'pｌｅｉn&#６1６11;|刨床millｅr铣床ｇｒｉnｄｅr磨床lｉnear cuｔting线切割eｌｅctrｉcal spａrkle电火花welder电焊机ｓｔａker=reviｔing ｍacｈｉne铆合机position职务（frｏｍａgenerａlｐersｐecｔive，ｇet hｉｇhpositionａｎd salarｙ，theｙcan bｕy aｈｏuse,a car,geｔmarried，child.)pｒesｉdent董事长(ｏur ｐｒｅｓiｄｅnｔiｓｅaｓy goinｇaｎd inteｌligｅnt iｎBeiｊing chanｇａn aｕtomｏｔive camｐany)genｅralｍaｎager总经理(reａlleａderｈａve the ｒｅspect ofｔheir peers aｎd their teams ，andthey treat oｎe asｅｑuaｌs ｉn teｒms ｏf ｔhe amount oｆthe ｒｅspｅｃt theｙare dｕe，fｒom the lowlieｓt ａsｓisｔａnt tｏthe general manager)ｆactory ｄirｅctｏr厂长deｐａrｔment directｏr部长ｄｅｐｕtｙｍaｎager |=ｖicemaｎaｇeｒ副理ｓｅction ｓｕpｅrvisor课长deputy sｅｃｔion ｓuｐerｖisoｒ=vicｅｓｅcｔioｎsｕｐerisoｒ副课长gｒoｕp lｅadeｒ/suｐervｉｓor组长linｅsuperviｓor线长assｉstant manａgｅr助理to moｖe, tｏｃarry,ｔo handle搬运be pｕtｉnｓtｏrage入库pａck packinｇ包装fiｎaｌinsｐection终检ｔoｃonｎect mａteriａl接料tｏreverse mａteｒｉaｌ翻料ｃleａning clｏｔh抹布to loａd ｍateriａl上料to ｕnlｏadｍaterｉal卸料to ｒeturn mateｒiａｌ/ｓtｏcｋtｏ退料scｒapｅd｜'skｒ＆aelig；pid|报废ｓcｒaｐｅ ..v.刮；削dｅｆicienｔpurcｈase来料不良(Deficient puｒchase ｃaused theprｏblｅm）mａnｕｆａcture prｏｃeduｒe制程deｆicienｔmanｕｆaｃtuｒiｎｇpｒoｃedure制程不良oxiｄatiｏn ｜＇ksi'deｉ＆#616１１;n|氧化scrａtch刮伤ｄents压痕。
史上最全汽车行业中英文专业术语表，很洋气的！
史上最全汽车行业中英文专业术语表，很洋气的！吃瓜的季节过去了，我们就再不做吃瓜技师了，从现在起，我们要向精英技师进阶：首先从提升专业术语学习开始，中英文对照，English哦，很高大上的！不学可惜了！发动机系统 Engine System引擎 Engine引擎波司 Engine Bush引擎修理包 Engine Gasket Kits引擎零件 Engine Parts凸轮轴 Camshaft凸轮轴链轮 Sprocket Camshaft皮带张力器 Tensioner曲轴 Crankshaft曲轴皮带盘 Crankshaft Pulley曲轴轴承片 Crankshaft Bearing汽门 Valve汽门座 Valve Seat汽门摇臂 Valve Arm汽门摇臂盖 Rocker Cover汽门弹簧 Valve Spring汽门导管 Valve Guide汽缸头(盖) Cylinder Head汽缸衬套 Cylinder Liner汽缸体 Cylinder Block波司垫片 Washer活塞 Piston活塞肖 Piston Pin活塞环 Piston Ring活塞衬套 Piston Liner飞轮 Flywheel飞轮环齿轮 Ring Gear of Flywheel时规炼条/皮带 Timing Chain/Belt连杆 Connecting Rod连杆轴承片 Connecting Rod Bearing摇臂轴 Rocker Arm Shaft汽门锁 Valve Cotter止推垫片 Thrust Washer共鸣箱 Resonator喷油嘴 Injection Nozzle燃料系统 Fueling System油箱 Fuel Tank油箱浮筒 Gauge Fuel Tank空气滤清器 Air Cleaner空气滤清器盖 Air Cleaner Cover空气滤清器导管 Air Intake Tube空气滤蕊 Air Cleaner Element消音器 Exhaust Muffler排气歧管 Exhaust Manifold排气管 Exhaust Pipe进气歧管 Intake Manifold节流阀 Throttle Valve燃油管 Fuel Pipe燃油帮浦 Fuel Pump燃油滤清器 Fuel Filter触媒转化器 Catalytic Converter柴油车黑烟净化器 Diesel Particulate Filter 时规炼条/皮带外盖 Timing Chain/Belt Cover 废气回收管 EGR Tube冷却系统 Cooling System水箱 Radiator水管 Water Hose水箱水管 Radiator Hose水帮浦 Water Pump水箱风扇 Radiator Fan风扇 Fan副水箱 Auxiliary Radiator节温器 Thermostat调节器 Regulator水箱支架 Radiator MountingA/C风扇 A/C Fan润滑系统 Lubrication System油底壳 Oil Pan自排车用滤油器 Oil Filter for Automatic Transmission 机油尺 Oil Level Gauge机油帮浦 Oil Pump机油滤清器 Oil Filter机油滤网 Oil Strainer机油尺导管 Oil Level Gauge Tube空调系统 Air-conditioning System冷气总成 A/C Assembly冷气配管 A/C Hose冷气导风管 A/C Duct冷气压缩机 A/C Compressor冷凝器 A/C Condenser暖气总成 Heater Assembly鼓风机 Blower Assembly蒸发器 Evaporator冷媒管 A/C Pipe储液瓶 A/C Receiver底盘系统 Chassis System下臂 Lower Arm上臂 Upper Arm支柱总成 Strut Assembly比例阀 Proportional Valve主轴、副轴 Mainshaft / Countershaft平衡杆 Stabilizer Bar扭力杆 T orsion Bar叶片弹簧 Leaf Spring刹车系统Brake System剎车分泵 Brake Cylinder剎车来令片 Brake Lining手剎车拉柄 Parking Brake Lever Shoe剎车油管(软) Brake Hose剎车油管(硬) Brake Tube剎车真空倍力器 Brake Vacuum Booster剎车总泵 Brake Master Cylinder手剎车拉柄 Parking Brake鼓式剎车盘 Brake Drum碟式剎车盘 Brake Disc鼓、碟式剎车器 Drum / Disc Brake Assembly 剎车真空管 Brake Boost Vacuum Tube车轮系统 Wheeling System轮毂 Wheel Hub轮胎 Tire轮胎汽门嘴 Tire Valve轮圈 Wheel Disk轮圈盖 Wheel Cover内胎(含内衬) Inner Tire (Flap)动力方向系统 Power Steering System动力转向油管 Power Steering Hose动力转向帮浦 Power Steering Pump转向连杆 Steering Linkage转向节臂 Knuckle转向齿轮箱 Steering Gear Box转向机柱 Steering Column转向总成 Steering Assembly控制拉线 Control Cable变速系统 Transmission System变速箱 Transmission Box变速箱外壳 Transmission Case曳力杆 Trailing Arm避震器前后活塞杆 Piston Rod of Front and Rear 自排变速箱修理包 Automatic Transmission齿条 Gear Rack离合器系统Clutch System离合器分泵 Clutch Cylinder离合器片 Clutch Disc离合器外壳 Clutch Case离合器总成 Clutch Assembly离合器总泵 Clutch Master Cylinder离合器释放轴承 Clutch Release Bearing汽车其他零部件Other parts of automobile排档杆 Shift Lever排档头 Knob球形接头 Ball Joint等速接头 C.V. Joint传动轴 Propeller Shaft辅助气囊 Air Bag踏板 Pedal齿轮 Gear横拉杆接头 Tie-Rod End螺旋弹簧 Coil Spring避震器 Shock Absorber电瓶 Battery中央门控Central Door Lock分电盘Distributor火花塞Spark Plug汽车用电子钟Digital Clock汽车音响Car Audio防盗器Car Burglar Alarm雨刷及雨刷连杆Wiper / Linkage 保险丝座Fuse Seat保险丝Fuse洗涤壶Windshield Washer配线Wire Harness汽车用光盘Car CD汽车用液晶显示器Car LCD调整器Regulator整流器Rectifier电子点火器Ignition Module倒车显示器Rear View Display 定速器Cruise ControllerHID。
汽车制造专业英语词汇大全(4000词条)
汽车专业词汇Assembly line组装线［ə’sɛmbli］Layout布置图Conveyer流水线物料板［kən’veɚ］Rivet table拉钉机[’rɪvɪt］Rivet gun拉钉枪Screw driver起子[skru］Electric screw driver电动起子[ɪ’lɛktrɪk] Pneumatic screw driver气动起子[numætɪk]worktable 工作桌OOBA开箱检查Out Of Box Auditfit together组装在一起fasten锁紧(螺丝) ［'fɑ:sən］fixture 夹具（治具）[’fɪkstʃɚ]pallet栈板(托盘)['pælət]barcode条码［’bɑrkod]barcode scanner条码扫描器［'skænɚ] fuse together熔合[fjuz］fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查[kɒz'metɪk］inner parts inspect内部检查［'ɪnɚ］thumb screw大头螺丝[θʌm]lbs. inch镑、英寸EMI gasket导电条［’ɡæskɪt]front plate前板[pleɪt］rear plate 后板［riə］chassis 基座［'ʃæsi］bezel panel面板［’bez(ə）l］['pænl]power button电源按键［’bʌtn］reset button重置键［riː'set]Hi-pot test of SPS高源高压测试Voltage switch of SPS电源电压接拉键sheet metal parts 冲件[ʃiːt]［’met(ə）l]plastic parts塑胶件［'plæstɪk］material check list物料检查表[mə'tɪərɪəl］work cell工作间[sel]trolley台车[’trɔli］carton纸箱［’kɑːt(ə)n］sub-line支线personnel resource department人力资源部[pɜːsə'nel] ［'risɔrs］production department生产部门planning department企划部QC Section品管科['sekʃən］stamping factory冲压厂［’stæmpɪŋ]painting factory烤漆厂［'peɪntɪŋ]molding factory成型厂［'məʊldɪŋ］common equipment常用设备[’kɒmən］［ɪ'kwɪpmənt]uncoiler and straightener整平机［ʌn'kɔilə]['streitənə]punching machine 冲床［'pʌntʃɪŋ］gripper机械手[’grɪpɚ］hydraulic machine油压机[haɪ'drɔlɪk]lathe车床［leɪð]planer ｜’plein&＃61611;|刨床［’pleɪnə］miller铣床['mɪlə］grinder磨床［’graɪndə］linear cutting线切割［’lɪnɪə]electrical sparkle电火花[ɪ'lektrɪk(ə）l］['spɑːk（ə)l］welder电焊机[’weldə］staker=reviting machine铆合机position职务president董事长［'prezɪd（ə)nt]general manager总经理special assistant manager特助[’speʃ(ə)l］［ə’sɪst（ə)nt]factory director厂长department director部长deputy manager ｜=vice manager副理section supervisor课长deputy section supervisor =vicesection superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理［ə’sɪst（ə）nt]to move，to carry, to handle搬运be put in storage入库['stɔːrɪdʒ]pack packing包装to apply oil擦油［ə’plaɪ]to file burr 锉毛刺［faɪl] [bɜː］final inspection终检to connect material接料［kə'nekt]to reverse material 翻料［rɪ’vɜːs］wet station沾湿台［wet］Tiana天那水cleaning cloth抹布[klɒθ］to load material上料to unload material卸料to return material/stock to退料scraped ｜'skræ；pid|报废［skrept] scrape 。
汽车行业英语专业词汇
汽车行业英语专业词汇1. Automobile industry - 汽车行业2. Automotive - 汽车的，汽车工业的3. Vehicle - 车辆4. Car - 汽车5. Truck - 卡车/载货车6. SUV (Sport Utility Vehicle) - 运动型多功能车7. Sedan - 轿车8. Hatchback -掀背车/斜背车9. Electric vehicle (EV) - 电动车10. Hybrid vehicle - 混合动力车11. Autonomous vehicle - 自动驾驶车辆12. Fuel efficiency - 燃油效率13. Emissions - 排放物14. Curb weight - 空车重量15. Horsepower (hp) - 马力16. Torque - 扭矩17. Engine - 发动机18. Transmission - 变速器19. Suspension - 悬挂系统20. Steering wheel - 方向盘21. Acceleration - 加速22. Braking system - 制动系统23. Exhaust system - 排气系统24. Fuel tank - 燃油箱25. Battery - 电池26. Tire - 轮胎27. Chassis - 底盘28. Bodywork - 车身29. Assembly line - 流水线30. Manufacturing - 制造业31. Production - 生产32. Quality control - 质量控制33. Supplier - 供应商34. Distribution - 分销35. Sales - 销售36. Marketing - 市场营销37. After-sale service - 售后服务38. Maintenance - 维修保养39. Dealership - 经销商40. Customer - 客户41. Consumer - 消费者42. Market share - 市场份额43. Competitive advantage - 竞争优势44. Brand - 品牌45. Model - 型号46. Price - 价格47. Promotion - 推广48. Advertisement - 广告49. Innovation - 创新50. Research and development - 研发。
汽车制造专业英语词汇大全
.汽车专业词汇Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch镑、英寸EMI gasket导电条front plate前板rear plate 后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS电源电压接拉键sheet metal parts 冲件plastic parts塑胶件material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线personnel resource department人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床gripper机械手hydraulic machine油压机lathe车床planer |'plein|刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vicesection superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skræpid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure 制程不良oxidation |' ksi'dein|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良feeding is not in place送料不到位stamping-missing漏冲education and training教育与训练proposal improvement提案改善spare parts备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车pallet栈板glove(s)手套glove(s) with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机chain链条槽magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小)slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位safety安全quality品质delivery deadline交货期cost成本engineering工程enterprise plan = enterpriseexpansion projects企划QC品管equipment设备classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products, up-to-gradeproducts良品defective products, not up-to-gradeproducts不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱mould change 换模mold repair修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate;barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cutmaterial, to input落料to impose lines压线to compress, compressing压缩to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, not qualified不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify修订to switch over to, switch---to throw--over switching over切换engineering, project difficulty工程瓶颈automation自动化to stake, staking, reviting铆合add lubricating oil加润滑油shut height of a die架模高度analog-mode device类模器argon welding氩焊stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸conveyer belt输送带transmission rack输送架inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, blockstop 定位块reset复位smoothly顺利dent压痕deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取processing, to process加工delivery, to deliver 交货to return delivenry to.registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked断裂to lubricate润滑common vocabulary for dieengineering模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die连续模compound die复合模punched hole冲孔to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder文件夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备work in progress product在制品casing = containerazation装箱quantity of physical invetory secondcount 复盘点数量quantity of customs count会计师盘,点数量the first page第一联filed by accounting department forreference会计部存查end-user/using unit(department)使用单位summary of year-end physicalinventory bills年终盘点截止单据汇总表bill name单据名称This sheet and physical inventorylist will be sent to accountingDepartment together (Those ofNHK will be sent to financialdepartment)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application status records ofyear-end physical inventory List andphysical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering moldtesting工程试模材料sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材Material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheetPCE组装厂生产排配表work order工令remark备注production control confirmation生产确认approved by核准department部门Stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质notes说明year-end physical inventorydifference analysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器nick缺口shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号)shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板upper plate上模板lower plate下模板die pad下垫板die holder下夹板bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣品质人员名称类QC quality control 品质管理人员FQC final quality control 终点品质管制人员IPQC in process quality control制程中的品质管制人员OQC output quality control 最终出货品质管制人员IQC incoming quality control 进料品质管制人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance出货质量保证人员QE quality engineering 品质工程人员品质保证类FAI first article inspection 新品首件检查TVR tool verification report 模具确认报告3B 3B 模具正式投产前确认CP capability index 能力指数CPK capability index of process 模具制程能力参数SSQA standardized supplier quality 合格供应商品质评估OOBA out of box audit 开箱检查QFD quality function deployment 品质机能展开FMEA failure model effectiveness analysis 失效模式分析8 disciplines 8项回复内容FA final audit 最後一次稽核CAR corrective action request 改正行动要求corrective action report 改正行动报告FQC运作类AQL Acceptable Quality Level 运作类允收品质水准S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ Average Output Quality 平均出厂品质AOQL Average Output QualityLevel 平均出厂品质Q/R/S Quality/Reliability/Service品质/可靠度服务MIL-STD Military-Standard 军用标准S I-S IV Special I-Special IV 特殊抽样水准等级P/N Part Number 料号L/N Lot Number 特采AOD Accept On Deviation 特采UAI Use As It 首件检查报告FPIR First Piece InspectionReport 百万分之一SPC Statistical Process Control统计制程管制SQC Statistical Quality Control统计品质管制R Range 全距AR Averary Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR GaugeReproducibility&Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它品质术语类QCC Quality Control Circle 品质圈QIT Quality Improvement Team品质改善小组PDCA Plan Do Check Action 计划执行检查总结ZD Zero Defect 零缺点QI Quality Improvement 品质改善QP Quality Policy 目标方针TQM Total Quality Management全面品质管理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低品质水准RMA Return Material Audit 退料认可QAN Quality Amelionrate Notice品质改善活动ADM Absolute Dimension Measuremat 全尺寸测量QT Quality Target 品质目标7QCT ools 7 Quality Controll Tools 品管七大手法通用之件类ECN Engineering Change Notes 工程变更通知(供应商)ECO Engineering Change Order 工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Specification In Process 制程检验规格SOP 开始生产IS Inspection Specification 成品检验规范PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QC Quality System 品质系统ES Engineering Standarization工程标准CGOO China General PCE龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司T TAIWAN 台湾IWS International WorkmanStandard 工艺标准ISO International StandardOrganization 国际标准化组织GS General Specification 一般规格CMCS C-China M-ManufactC-Compaq S-Stamping Compaq产品在龙华冲压厂制造作业规范CQCA Q-Quality A-AssemblyCompaq产品在龙华组装厂品管作业规范CQCP P-Painting Compaq产品在龙华烤漆厂品管作业规范部类PMC Production & MaterialControl 生产和物料控制PPC Production Plan Control 生产计划控制MC Material Control 物料控制ME Manafacture Engineering 制造工程部PE Project Engineering 产品工程部A/C Accountant Dept 会计部DC Document Center 资料中心QE Quality Engineering 品质工程(部)QA Quality Assurance 品质保证(处)QC Quality Control 品质管制(课)PD Product Department 生产部LAB Labratry 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供应商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号其它OEM 主机厂PCE Personal Computer Enclosure 个人电脑外设PC Personal Computer 个人电脑CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大陆PRC People's Republic of China中国大陆U.S.A the United States ofAmerica 美国A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存/及时供货I/O Input/Output 输入/输出NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electry-static Discharge 静电排放5S 希腊语整理,整顿,清扫,清洁,教养ATIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光碟CD-ROM Compact DiskRead-Only Memory 只读光碟FDD Floppy Disk Drive 软碟机HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CAV Cavity 模穴CAD Computer Aid Design 计算机辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly DeliveryRequitement 周出货需求C?T Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间)S/T Standard Time 标准时间P/M Product Market 产品市场3CComputer,Commumcation,Consumer electronic's 消费性电子5WIHWhen,Where,Who,What,Why,Howto5MMan,Machine,Material,Method,Mea surement4MIHMan,Materia,Money,Method,Time 人力,物力,财务,技术,时间(资源) SQA Strategy Quality Assurance 策略品质保证DQA Desigh Quality Assurance 设计品质保证MQA Manufacture Quality Assurance 制造品质保证SSQA Sales and service Quality Assurance 销售及服务品质保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic Magnetion Inspect 高磁测试FMI Frequency Modulatim Inspect 高频测试B/M Boar/Molding(flat cable) C/P Connector of PCA/P AssemblySPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Vedio DiskVCD Vdeio Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AIDManufacturingCAE Computer AID EngineeringABIOS Achanced Basic input/output system 先进的基本输入/输出系统CMOS Complemeruary MetollOxide Semiconductor 互补金属氧化物半导体PDA Personal Digital Assistant个人数字助理IC Integrated Circuit 集成电路ISA Industry StandardArchitecture 工业标准体制结构MCA Micro Channel Architecture微通道结构EISA Extended Industry StandardArchitecture 扩充的工业标准结构SIMM Single in-line memorymodule 单项导通汇流组件DIMM Dual in-line MemoryModule 双项导通汇流组件LED Light-Emitting Diode 发光二级管FMEA Failure Mode Effectivenes失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Calle 排线PCB Printed Circuit Board 印刷电路板CAR Correction Action Report改善报告NG Not Good 不良WPR Weekly DeliveryRequirement 周出货要求PPM Parts Per Million 百万分之一TPM Total ProductionMaintenance 全面生产保养MRP Material RequiremcntPlanning 物料需计划OC Operation System 作业系统TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProceduneEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material Size LMC Least Material Condition LMS Least Material Size模具技术用语各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming ?泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matchedmould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landedplunger mold 有肩柱塞式模具shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold活动式模具clod hobbing 冷挤压制模louveringdie 百叶窗冲切模composite dies 复合模具manifolddie 分歧管模具counter punch 反凸模modularmold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具family mold 反套制品模具plaster mold 石膏模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具split mold 双并式模具sprueless mold 无注道残料模具sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoketype die 轭型模模具厂常用之标准零配件air vent valve 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁)cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drivebearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejectorleader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘?flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶?冲头headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locatingring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套manifold block 歧管档块master plate 靠模样板match plate分型板mold base 塑胶模座mold clamp铸模紧固夹mold platen 模用板moving bolster换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paring line分模线parting lock set 合模定位器passguide 穴型导板peened head punch 镶入式冲头pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin嵌件梢retainer plate 托料板return pin 回位梢riding stripper 浮动脱模器ringgate 环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton骨架slag riser 冒渣口slide(slide core)滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架spindle 主轴sprue 注道sprue bushing 注道衬套sprue bushing guide 注道导套sprue lock bushing 注道定位衬套spue line 合模线square key 方键square nut 方螺帽square thread 方螺纹stop collar 限位套stop pin 止动梢stop ring 止动环stopper 定位停止梢straight pin 圆柱? stripper bolt 脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱support pin 支撑梢supporting plate 托板sweeptemplete 造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝模板模具常用之工作机械3D coordinate measurement 三次元量床boring machine 搪孔机cnc milling machine CNC铣床contouring machine 轮廓锯床copy grinding machine 仿形磨床copy lathe 仿形车床copy milling machine 仿形铣床copy shaping machine 仿形刨床cylindrical grinding machine 外圆磨床die spotting machine 合模机engraving machine 雕刻机engraving E.D.M. 雕模放置加工机form grinding machine 成形磨床graphite machine 石墨加工机horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心internal cylindricalmachine 内圆磨床jig grinding machine 冶具磨床lap machine 研磨机machine center 加工制造中心multi model miller 靠磨铣床NC drilling machine NC钻床NC grinding machine NC磨床NC lathe NC车床NC programming system NC程式制作系统planer 龙门刨床profile grinding machine 投影磨床projection grinder 投影磨床radial drilling machine 旋臂床shaper 牛头刨床surface grinder 平面磨床try machine 试模机turret lathe 转塔车床universal toolgrinding machine 万能工具磨床vertical machine center 立式加工制造中心wire E.D.M. 线割放电加工机检验量测工具用语。
汽车制造业英语词汇(较全)
汽车制造业英语词汇(较全)汽车制造业英语词汇是在汽车制造业领域中使用的专业术语和词汇的总称。
以下是一份较全的汽车制造业英语词汇表。
A- ABS (Antilock Braking System): 防抱死制动系统- Accelerator: 油门- Airbag: 安全气囊- Alternator: 发电机- Assembly line: 生产线- Automatic transmission: 自动变速器- Axle: 轴B- Battery: 蓄电池- Bodywork: 车身工作- Brake: 制动器- Bumper: 缓冲器C- Camshaft: 凸轮轴- Carburetor: 化油器- Chassis: 底盘- Clutch: 离合器- Crankshaft: 曲轴D- Dashboard: 仪表盘- Diesel engine: 柴油发动机- Distributor: 分配器- Drive shaft: 传动轴- Driver: 驾驶员E- Engine: 发动机- Exhaust pipe: 排气管- Expansion tank: 膨胀水箱F- Fan belt: 风扇皮带- Flywheel: 飞轮- Fuel pump: 燃油泵G- Gearbox: 变速箱- Generator: 发电机- GPS (Global Positioning System): 全球定位系统H- Headlight: 前大灯- Horn: 喇叭I- Ignition: 点火- Indicator: 转向灯- Injection: 喷射- Intercooler: 中冷器L- Light bulb: 灯泡M- Manual transmission: 手动变速器- Motorcycle: 摩托车- Muffler: 消音器O- Oil filter: 污垢筛选器- Oil pump: 油泵P- Piston: 活塞- Power steering: 动力转向- Radiator: 散热器R- Rearview mirror: 后视镜- Rim: 轮辋S- Seat belt: 安全带- Shock absorber: 减震器- Spark plug: 火花塞- Steering wheel: 方向盘- Suspension: 悬挂系统T- Throttle: 油门- Tire: 轮胎- Transmission: 变速器W- Wheel: 轮子- Windshield: 挡风玻璃- Windshield wiper: 雨刷器以上是一份较全的汽车制造业英语词汇表，希望能对您有所帮助。
汽车制造专业英语词汇大全
汽车专业词汇Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch镑、英寸EMI gasket导电条front plate前板rear plate 后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS电源电压接拉键sheet metal parts 冲件plastic parts塑胶件material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线personnel resource department人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床gripper机械手hydraulic machine油压机lathe车床planer |'plein|刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vicesection superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skræpid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dein|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良feeding is not in place送料不到位stamping-missing漏冲education and training教育与训练proposal improvement提案改善spare parts备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓administration/general affairsdept总务部automatic screwdriver电动启子thickness gauge厚薄规power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车pallet栈板glove(s)手套glove(s) with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机chain链条槽magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger 尺寸偏大(小)slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位safety安全quality品质delivery deadline交货期cost成本engineering工程enterprise plan = enterpriseexpansion projects企划QC品管equipment设备classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products, up-to-gradeproducts良品defective products, notup-to-grade products不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱mould change 换模mold repair修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate;barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cutmaterial, to input落料to impose lines压线to compress, compressing压缩to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, not qualified不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for 准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify修订to switch over to, switch---to throw--over switching over切换engineering, project difficulty 工程瓶颈automation自动化to stake, staking, reviting铆合add lubricating oil加润滑油shut height of a die架模高度analog-mode device类模器argon welding氩焊stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸conveyer belt输送带transmission rack输送架inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece,block stop 定位块reset复位smoothly顺利dent压痕deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取processing, to process加工delivery, to deliver 交货to return delivenry to.registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked断裂to lubricate润滑common vocabulary for dieengineering模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die 连续模compound die复合模punched hole冲孔to cutedges=side cut=side scrap 切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder文件夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备work in progress product在制品casing = containerazation装箱quantity of physical invetorysecond count 复盘点数量quantity of customs count会计师盘,点数量the first page第一联filed by accounting departmentfor reference会计部存查end-user/using unit(department)使用单位summary of year-end physicalinventory bills年终盘点截止单据汇总表bill name单据名称This sheet and physical inventorylist will be sent to accountingDepartment together (Those of NHKwill be sent to financialdepartment)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application status records ofyear-end physical inventory Listandphysical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering moldtesting工程试模材料sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材Material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheetPCE组装厂生产排配表work order工令remark备注production control confirmation 生产确认approved by核准department部门Stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质notes说明year-end physical inventorydifference analysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventorylist备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器nick缺口shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号)shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板upper plate上模板lower plate下模板die pad下垫板die holder下夹板bottom block下垫脚bottom plate下托板(底板)stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣品质人员名称类QC quality control 品质管理人员FQC final quality control 终点品质管制人员IPQC in process quality control制程中的品质管制人员OQC output quality control 最终出货品质管制人员IQC incoming quality control进料品质管制人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 品质工程人员品质保证类FAI first article inspection 新品首件检查TVR tool verification report 模具确认报告3B 3B 模具正式投产前确认CP capability index 能力指数CPK capability index of process 模具制程能力参数SSQA standardized supplier quality 合格供应商品质评估OOBA out of box audit 开箱检查QFD quality function deployment 品质机能展开FMEA failure model effectiveness analysis 失效模式分析8 disciplines 8项回复内容FA final audit 最後一次稽核CAR corrective action request改正行动要求corrective action report 改正行动报告FQC运作类AQL Acceptable Quality Level运作类允收品质水准S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ Average Output Quality 平均出厂品质AOQL Average Output QualityLevel 平均出厂品质Q/R/SQuality/Reliability/Service 品质/可靠度服务MIL-STD Military-Standard 军用标准S I-S IV Special I-Special IV特殊抽样水准等级P/N Part Number 料号L/N Lot Number 特采AOD Accept On Deviation 特采UAI Use As It 首件检查报告FPIR First Piece InspectionReport 百万分之一SPC Statistical Process Control统计制程管制SQC Statistical Quality Control统计品质管制R Range 全距AR Averary Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR GaugeReproducibility&Repeatability量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它品质术语类QCC Quality Control Circle 品质圈QIT Quality Improvement Team品质改善小组PDCA Plan Do Check Action 计划执行检查总结ZD Zero Defect 零缺点QI Quality Improvement 品质改善QP Quality Policy 目标方针TQM Total Quality Management 全面品质管理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低品质水准RMA Return Material Audit 退料认可QAN Quality Amelionrate Notice 品质改善活动ADM Absolute Dimension Measuremat 全尺寸测量QT Quality Target 品质目标7QCTools 7 Quality Controll Tools 品管七大手法通用之件类ECN Engineering Change Notes工程变更通知(供应商)ECO Engineering Change Order工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Specification In Process制程检验规格SOP 开始生产IS Inspection Specification 成品检验规范PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QC Quality System 品质系统ES Engineering Standarization工程标准CGOO China General PCE龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司T TAIWAN 台湾IWS International WorkmanStandard 工艺标准ISO International StandardOrganization 国际标准化组织GS General Specification 一般规格CMCS C-China M-ManufactC-Compaq S-Stamping Compaq产品在龙华冲压厂制造作业规范CQCA Q-Quality A-AssemblyCompaq产品在龙华组装厂品管作业规范CQCP P-Painting Compaq产品在龙华烤漆厂品管作业规范部类PMC Production & MaterialControl 生产和物料控制PPC Production Plan Control 生产计划控制MC Material Control 物料控制ME Manafacture Engineering 制造工程部PE Project Engineering 产品工程部A/C Accountant Dept 会计部DC Document Center 资料中心QE Quality Engineering 品质工程(部)QA Quality Assurance 品质保证(处)QC Quality Control 品质管制(课)PD Product Department 生产部LAB Labratry 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供应商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号其它OEM 主机厂PCE Personal Computer Enclosure个人电脑外设PC Personal Computer 个人电脑CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大陆PRC People's Republic of China中国大陆U.S.A the United States ofAmerica 美国A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存/及时供货I/O Input/Output 输入/输出NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electry-static Discharge静电排放5S 希腊语整理,整顿,清扫,清洁,教养ATIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光碟CD-ROM Compact Disk Read-OnlyMemory 只读光碟FDD Floppy Disk Drive 软碟机HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CAV Cavity 模穴CAD Computer Aid Design 计算机辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly Delivery Requitement 周出货需求C?T Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间)S/T Standard Time 标准时间P/M Product Market 产品市场3CComputer,Commumcation,Consumer electronic's 消费性电子5WIHWhen,Where,Who,What,Why,How to 5MMan,Machine,Material,Method,Mea surement4MIHMan,Materia,Money,Method,Time人力,物力,财务,技术,时间(资源) SQA Strategy Quality Assurance 策略品质保证DQA Desigh Quality Assurance设计品质保证MQA Manufacture QualityAssurance 制造品质保证SSQA Sales and service QualityAssurance 销售及服务品质保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic MagnetionInspect 高磁测试FMI Frequency Modulatim Inspect高频测试B/M Boar/Molding(flat cable)C/P Connector of PCA/P AssemblySPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Vedio DiskVCD Vdeio Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID ManufacturingCAE Computer AID EngineeringABIOS Achanced Basic input/output system 先进的基本输入/输出系统CMOS Complemeruary Metoll OxideSemiconductor 互补金属氧化物半导体PDA Personal Digital Assistant个人数字助理IC Integrated Circuit 集成电路ISA Industry StandardArchitecture 工业标准体制结构MCA Micro Channel Architecture微通道结构EISA Extended Industry StandardArchitecture 扩充的工业标准结构SIMM Single in-line memorymodule 单项导通汇流组件DIMM Dual in-line Memory Module双项导通汇流组件LED Light-Emitting Diode 发光二级管FMEA Failure Mode Effectivenes失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Calle 排线PCB Printed Circuit Board 印刷电路板CAR Correction Action Report改善报告NG Not Good 不良WPR Weekly Delivery Requirement周出货要求PPM Parts Per Million 百万分之一TPM Total Production Maintenance 全面生产保养MRP Material Requiremcnt Planning 物料需计划OC Operation System 作业系统TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProceduneEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material Condition MMS Maximum Material SizeLMC Least Material Condition LMS Least Material Size模具技术用语各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸 precision forging 精密锻造cold forging 冷锻 press forging冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形 rotaryforging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming ?泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landedplunger mold 有肩柱塞式模具shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模 loose mold活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具 manifolddie 分歧管模具counter punch 反凸模modularmold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具family mold 反套制品模具plaster mold 石膏模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具runless injection mold 无流道冷料模具 sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavitymold 单腔模具split mold 双并式模具 spruelessmold 无注道残料模具sweeping mold 平刮铸模 swing die振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具 universalmold 通用模具unscrewing mold 退扣式模具 yoketype die 轭型模模具厂常用之标准零配件air vent valve 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁)cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢 dowel hole 导套孔dowel pin 合模梢 dozzle 辅助浇口dowel pin 定位梢 draft 拔模锥度draw bead 张力调整杆drivebearing 传动轴承ejection pad 顶出衬垫 ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘? flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶?冲头headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块 locking block 定位块locking plate 定位板 loose bush活动衬套manifold block 歧管档块master plate 靠模样板matchplate 分型板mold base 塑胶模座 mold clamp 铸模紧固夹mold platen 模用板movingbolster 换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paringline 分模线parting lock set 合模定位器 passguide 穴型导板peened head punch 镶入式冲头pin gate 针尖浇口 plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆 pusher pin 衬套梢rack 机架 rapping rod 起模杆re-entrant mold 凹入模 retainerpin 嵌件梢retainer plate 托料板 return pin回位梢riding stripper 浮动脱模器 ring gate 环型浇口roller 滚筒 runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞 set screw 固定螺丝shedder 脱模装置 shim 分隔片shoe 模座之上下模板 shoot 流道shoulder bolt 肩部螺丝 skeleton 骨架slag riser 冒渣口slide(slide core) 滑块slip joint 滑配接头 spacer block 间隔块spacer ring 间隔环 spider 模蕊支架spindle 主轴 sprue 注道sprue bushing 注道衬套sprue bushing guide 注道导套sprue lock bushing 注道定位衬套spue line 合模线 square key 方键square nut 方螺帽 square thread方螺纹stop collar 限位套 stop pin 止动梢stop ring 止动环 stopper 定位停止梢straight pin 圆柱? stripper bolt脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱support pin 支撑梢supporting plate 托板sweeptemplete 造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝模板模具常用之工作机械3D coordinate measurement 三次元量床 boring machine 搪孔机cnc milling machine CNC铣床contouring machine 轮廓锯床copy grinding machine 仿形磨床copy lathe 仿形车床copy milling machine 仿形铣床copy shaping machine 仿形刨床cylindrical grinding machine 外圆磨床 die spotting machine 合模机engraving machine 雕刻机engraving E.D.M. 雕模放置加工机form grinding machine 成形磨床graphite machine 石墨加工机horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心 internal cylindricalmachine 内圆磨床jig grinding machine 冶具磨床lap machine 研磨机machine center 加工制造中心multi model miller 靠磨铣床NC drilling machine NC钻床NC grinding machine NC磨床NC lathe NC车床NC programming system NC程式制作。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39
BIQ BOM BOP BPD BPP BPR C3P CAD CAE CAM CE CKD CMM Cost book CIM CIP COMMWIP CPIP Cpk
40
CS1
41
CS2
汇 众 专 业 技 术 词 汇 （英文）汇 总
序号
1 2 3 4
术
3G 3M 5M AAR
语
5
Action plan
6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
ADV ADV–DV A/D/V P&R ADV–PV AEM AIAG Andon AP APQP APO AS ASQE ATT Audit Bidlist
132
PDCA
133 134 135 136
PDT PFMEA PFEP Pilot
137 138 139 140 141
PM PMP PO Poke Yoke PPAP
142
PPM
143 144 145 146 147 148 149 150 151
PPE Ppk PPV PQC PR/R PRTS PS PSA PTR
MCR MOP MPC MPCE MRD
112
MS
113
MSA
114 115
MTBF MTTR
116
MVBns/NS
117 118 119 120 121 122 123
MVBs/S NA NAO NBH N.O.D. NPV NVA
124 125 126 127 128 129 130 131
OC OEM OTS PAD PARETO PCR PC&L PCPA
Built In Quality 制造质量 Bill of Materials 材料清单 Bill of Process 过程清单 Bussiness Plan Deployment 业务计划实施 Best People Practices 最佳人员准则 Business Plan Recompose 业务流程重组 CAD、CAM、CAE与PDM，CAD、CAM、CAE和产品数据管理 Computer-aided design (drafting) 计算机辅助设计 Computer-Aided Engineering, (pronounced Kaye) 计算机辅助工程 Computer-aided manufacturing 计算机辅助制造 Concourrent Engineering 并行工程 Completely knocked down Coordinate Measuring Machine 三坐标测试仪 采购物料成本预算 Computer integrated Manufacturing 集成制造 Continuous Improvement Process 持续改进过程 7种浪费 the Current Product Improvement Process 现有产品改进程序 Capability Index for a stabile process 过程能力指数 Control shipping 1: 一级受控：由供应商执行额外的100%检验，费用由供应商 承担 Control shipping 2: 二级受控：由汇众指派第三方执行额外的100%检验，费用 由供应商承担 Cycle Time 周期时间 Component Technical Specifications 零件技术规范 Direct buy Design For Assenbly 装配性设计
152
Prototype Vehicle （Sample）
153 154 155 156
QCC QCD QCOS QFD
157
QRK
158 159 160
QSA QSDT QTC
161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176
Design for Manufacturability / Design for Assembly 可制造性／可装配性设计 Design Failure Modes and Effects Analysis 设计失效模式分析 Design Of Experiments 实验设计 Defects per vehicle 每辆车缺陷数 Design Release Engineer 设计发放工程师 Element Time 基本动作周期 Engineering Work Order 工程更改指令 Functional Evaluations 功能评估 First-In,First-Out 先进先出 Failure Mode and Effects Analysis 失效模式和后果分析 Flexible Manufacturing Systems 柔性制造系统 Fixed Position Stop 定点停 Fault Tree Analysis 故障树分析 First Time Quality 下线合格率 Global Customer Audit 全球客户评审 Geometric Dimensioning & Tolerancing 几何尺寸&公差 Golbal Delivery System 全球搬运系统 General Motors 通用汽车公司 General Motors Europe 通用汽车欧洲分部 Global Manufacturing System 全球制造系统 General Procedure 总体步骤 Production Approval 生产批准程序 Supplier Submission of Material for Proc. Application 供应商零部件材料生产申请程序
92 93 94 95 96
JIS JPH JSC KANBAN Kaizen
97
KCC
98
KCDS
99
Kick-Off Meeting
100
KPC
101
LAO
102
Layouts
103 104 105
LCR Lead Time LLP
106
Lean Manufacturing
107 108 109 110 111
68
GP-4
69 70
GP-5 GP-6
71
GP-7
72 73
GP-8 GP-9
74
GP-10
75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91
GP-11 GP-12 GPDS GPS GQTS GR&R GVDP HR IPTV I-Chart I.E. IOM IOS IRR I.T. JES JIT
SPQRC SQ SQA SQC SQE SQIP SSF SSTS S.T.E.P TBD
192Байду номын сангаас
Tier 1 Supplier
193 194 195 196 197 198 199 200 201 202
Tier 2 Supplier TA TOC TPM TQC TQM TR TT UG VDP
Problem Reporting & Resolution 问题报告和解决程序 Supplier Requirement for Match Check Material 供应商材料认可程序 Supplier Requirement for Comp. Verification & Trace. 供应商零部件认可和追溯要求程序 Continuous Improvement Procedure 持续改进程序 Run @ Rate Process 节拍生产 Evaluation & Accreditation of Supplier Testing Facility 供应商实验/试验室认可程序 Prototype Material Certification Procedure 手工样件认可程序 Early Production Containment Procedure 早期生产遏制程序 Global Product Description System 全球产品描述系统 Global Purchasing System 全球采购系统 Global Quality Tracking System 全球质量跟踪系统 Gage Repeatability and Reproducibility 量具的重复性与再现性 Global Vehicle Development Process 全球车辆开发过程 Human Resource 人力资源 Incidents per Thousand Vehicles 每千辆车缺陷数 GP12程序中使用的自检记录表 Industry Engineering 工业工程 Inspection Operator Method 操作视察方法 Inspection Operator Summary 操作视察要领 Internal Rate of Return 内部收益率 Index Time 指数时间 Job Element Sheet 工作要素单 Just In Time Manufacturing Process 拉动式（及时）生产
203
VLE
204
WBS
205
WWP
众 专 业 技 术 词 汇 （英文）汇 总
解 释
Go and see(开展现场调查)、Get the fact(了解问题根 本原因)、Grasp the countermeasure(制定出有效措施) Muda、Mura、Mari，浪费、无稳、无理。 常作改善的核查点 Manpower,Machine,Material,Mathod,Measurement 人员，机器，材料，方法，测量 Appearance Approval Report 外观批准报告 Steps required to resolve gaps between Estimated Completion Dates/Actual Completion Dates and Required Completion Dates. A description of how barriers to improvement or roadblocks will be addressed 行动计划 Analysis/Development/Validation 分析／开发／验证 ADV Design Validation ADV设计验证 Analysis/Development/Validation Plan and Report 分析／开发／验证计划和报告 ADV Product Validation ADV产品验证 Assemblabrlity Evaluation Method 可装配性评估方法 Automotive Industries Action Group 暗灯 Advanced Purchasing 先期采购 Advanced Product Quality Planning 产品质量先期策划 Asian Pacific Operations 亚太分部 Address System 地址系统 Advanced Supplier Quality Engineer 先期供应商质量工程师 Actual Take Time 实际单件工时 基于抽样来确定供方文件化的质量体系实施有效性的现场 验证活动 潜在供应商清单