建筑词汇

一、工程施工类（一）工程施工、土建类开挖与支护明挖（open excavation）bench excavation，台阶开挖concrete excavation，砼开挖fault excavation，断层开挖foundation excavation，基础开挖local excavation，局部开挖mass（bulk）excavation，大面积开挖protective layer excavation，保护层开挖rock excavation，岩石开挖slope excavation，边坡开挖soft ground excavation，软基开挖soil excavation，土方开挖structural excavation，结构开挖tooth excavation，齿槽开挖unclassified material excavation，不分类开挖coefficient of nonuniformity，开挖不均匀系数cutoff trench截水槽dewatering（drainage），排水excavation pit，开挖基坑intensity of excavation，开挖强度overexcavation（overbreak），超挖pump sump，水泵坑underexcavation（underbreak），欠挖underbreak treatment，欠挖处理洞挖及地下开挖（tunnel and underground excavation）a round of excavation，一个开挖循环adit，支洞advance，进尺advanced depth，进尺深度breaking hole，崩落孔cushion hole，缓冲孔drift，掏槽bottom drift，底部掏槽center drift，中央掏槽side drift，边部掏槽top drift，顶部掏槽drilling，钻孔driving（progress）rate，进尺率easer，掏槽孔erecting supports for the roof and side wall，对顶拱及边墙进行支护full face excavation，全断面开挖heading and bench excavation，导洞与台阶开挖loading and hauling muck（mucking），装拉碴loading（charging），装药perimeter hole，周边孔pilot tunnel，导洞removing dust，除尘removing ground water，清除地面积水shooting the explosive（blasting），放炮，爆破top heading excavation，上导洞开挖ventilation，通风钻孔爆破（drilling and blasting）abandoned hole，废孔average hole depth，平均孔深average quantity used in unit volume blasted，平均单耗blasting result，爆破结果blockness，块度controlled perimeter blasting，周边控制爆破data of explosive filled，装药参数data of holes drilled，钻孔参数delayed blasting，延时爆破exploratory hole，探孔explosive quantity，药量explosive quantity in a sound，单响药量handing misfire，处理哑炮light charge，少量装药loosening blasting，松动爆破pattern，布孔方式distance between holes，孔距distance between rows，排距post shearing blasting，微差爆破prespliting blasting，预裂参数quantity of holes，孔数smooth blasting，光面爆破岩石支护（rock support）expansion shell rock bolt，胀壳式张拉锚杆feature rock anchor，随机锚索feature rock bolt，随机张拉锚杆feature rock dowel，随机砂浆锚杆feature rock reinforcement，随机加固lattice girder，钢珩架，格够大梁pattern cement grouted rock dowel，系统水泥砂浆锚杆pattern resin grouted rock dowel，系统树脂浆锚杆pattern rock dowel，系统砂浆锚杆pattern rock reinforcement，系统加固permanent rock support，永久支护post-tensioned cement grouted tendon rock anchor，后张拉水泥浆锚索rebound material，回弹料return rock bolt，回头张拉锚杆return rock reinforcement，回头加固shotcrete anchorage，喷锚shotcrete with wire mesh，挂网喷砼steel fabric shotcrete，钢纤维喷砼steel rib，钢拱架temporary rock support，临时支护tensioned resin grouted rock bolt，树脂张拉锚杆土石料的填筑及碾压（working sequence）backfill，回填blend，混合compact，碾压controlled sprinkling，控制散水cut the slope，削坡dump，卸料exploit，开采level，整平load，装料moisture condition，分水调节place and spread，摊铺remove，清除replace，重新填筑retread（do the work again），返工scarify，翻松，刨毛screen and wash，筛分和冲洗take sample，取样test，测试transport，运输treat，处理trim，休整缺陷（defects）calcium particles姜石contaminated material，受污染料declination of the boundary，料界偏差dry，干燥lack of compaction，漏压lump，结块muddy，泥泞oversize material，超粒径料pocket，囊穴seepage，渗流separation，分离shear area，剪力区lens，透镜体其他（others）bonding surface，结合面byproduct，副产品controlling parameter，控制参数fill placement record，填筑记录frog area，蛙夯区required embankment，必要填方subzone，分区混凝土（concrete）air-entrained concrete（aerated concrete）加气混凝土asphalt concrete，沥青混凝土blinding concrete，垫层混凝土cast-in-site（site，place）concrete，现浇混凝土plastic concrete，塑性混凝土fibrous concrete，纤维混凝土fist stage concrete，一期混凝土foamed concrete，泡沫混凝土high-performance concrete，高性能混凝土high-strength concrete，高强混凝土intrusion concrete，压浆混凝土lean concrete（poor concrete），贫混凝土lightweight aggregate concrete，轻骨料混凝土mass concrete，大体积混凝土non-fines concrete，无砂混凝土non-plastic concrete，干硬性混凝土non-shrinkage concrete 无收缩混凝土normal concrete，常态混凝土plain concrete，素混凝土porous concrete，多孔混凝土prestressed concrete，预应力混凝土reinforced concrete，钢筋混凝土pump concrete，泵送混凝土roller compacted concrete（rollcrete），碾压混凝土second stage concrete，二期混凝土作业（activity）clearance（cleaning），清理concrete pouring（placement，casting），混凝土养护curing，养护membrance curing，薄膜养护moist curing，湿润养护normal curing，标准养护stream curing，蒸汽养护repairing，修补scabbling（chipping，roughening），凿毛greencutting，冲毛surface finishing，收面vibrating，振捣缺陷（defects）bug hole （pitted surface）麻面cavity狗洞cold joint，冷缝crack，裂缝deformation，变形depression，坑洼fire-damaged concrete，火损坑formwork shifting（moving），跑模grout leakage，漏浆（挂帘）honeycomb，蜂窝incomplete vibration，不完全振捣，漏振irregularity，不规则segregation（bleeding），离析stair（staggered joint），错台tie rod hole，拉杆孔water leakage，漏水water seepage，渗水外加剂（admixture）accelerator，速凝剂air-entraining agent，引气剂bloating（bulking，expansion）agent，膨胀剂coloring admixture，着色剂early-strength admixture，早强剂gas-forming admixture，发气剂fluidizer，塑化剂retarding agent，缓凝剂set-controlling admixture，调凝剂super-plasticizer，增塑剂，高效减水剂surface-active agent，表面活性剂water-reducing agent，减水剂accelerating water reducer，速凝型减水剂retarding water reducer，缓凝型减水剂waterproof agent，防水剂指标（indexes）compressive strength，抗压强度compressive stress，压应力concrete class，混凝土等级final strength，终凝强度graduation，级配graduation curve，级配曲线impermeability，抗渗性initial setting strength，初凝强度mix design，配合比设计resistance to freezing and thawing，抗洞融性shear strength，抗剪强度slump，塌落度specific weight/gravity，比重stability against sliding，抗滑稳定性strain，应变surface finish，表面平整度tensile strength[MSOffice1] ，抗拉强度tensile stress，拉应力thermal stress，温度应力water-cement ratio，水灰比working stress，工作应力其他（others）acceptance，验收age，龄期aggregate，骨料fine aggregate，细骨料coarse aggregate，粗骨料air pocket，气囊airtightness，气密性alternative，替代物，替换方法apply，应用，施加bending moment，弯矩block，仓号binding strength，黏结强度calibration，标定cement anchor，锚固卷concrete plug，混凝土塞concrete precast element，混凝土预制件concrete release sheet，发料单construction joint，施工缝contamination/pollution，污染conversion（reconstruction），改建coverage，覆盖范围curing agent，养护剂delivery sheet，运料单direct discharge，直接入仓elevation，高程，正视图epoxy mortar application，环氧砂浆抹面existing，现有的expansion joint，伸缩缝facilitate，使轻易，使便利gabion，铅丝笼humidity，湿度identify，识别，标志ingredient，成分，配料inspection，视察，检查，验收preliminary inspection，初验final inspection，终验appearance inspection，外观检查intact，未被触动的，完整的inter-tower joint，踏间缝introduce into，将穿入isolate，隔离laitance，乳浆皮layer（lift）height，层高meet design requirement，满意设计要求moment of inertia，惯性距pocket（box out，preset hole），预留孔post-cooling，后冷却post tensioning，后张拉pre-cooling，预冷却pre-stressing，预应力pre-tensioning，先张拉pull-off test，拉拔试验reinforcement cover，钢筋保护层remark，备注section area，截面面积shearkey，抗剪键key groove，键槽shotcrete dry-mix process，干喷砼生产shotcrete wet-mix process，湿喷砼生产simplify，简化simultaneously，同时的spacer，水泥垫块spacing，间距stress concentration，应力集中symmetry，对称technical data，技术参数temperature control，温度控制temperature difference，温差temperature rise（gain），温度升高theoretical elongation，理论伸长量unloading，卸载water stop，止水PVC water stop，PVC止水Rubber water stop，橡皮止水Copper water stop，铜止水Watertightness，闭水性Winter protection，冬季保温模板（formwork，shuttering form）erecting（setting up，fixing）formwork，立模stripping（removing，dismantling）formwork，拆模bond breaker，脱模剂climbing cone，爬升锥dam bracket，大坝支架distance piece，横支撑double-curvature formwork，双曲模板flat formwork，平面模板formwork oil，模板油pigtail anchor，猪尾筋retractable formwork，进退式模板shearkey box，键槽盒sliding formwork，滑模steel form carrier，钢模台车steel formwork，钢模steel waling，钢围令，钢支撑stopend，堵头，封堵模板temporary formwork，临时模板tie rod（form tie），拉杆tiltable formwork，侧斜式模板vault and invert formwork，顶拱及底拱模板wood formwork，木模钢筋（reinforcement rebar）distribution bar，分布筋dowel，插筋horizontal bar，水平筋lap length，搭接长度main stress bar，主应力overlap，搭接shear bar，剪力筋splice welding，绑条焊接starter bar，起始筋，苗子筋stirrup，箍筋support，架立筋vertical bar，竖直筋灌浆（grouting）backfill grouting，回填灌浆consolidation grouting，固结灌浆contact grouting，接触灌浆curtain grouting，帷幕灌浆gap grouting，接缝灌浆gravity grouting，自重灌浆jet grouting，旋喷灌浆multi-stage grouting，多次灌浆pressure grouting，压力灌浆ring grouting，环行灌浆single-stage grouting，一次灌浆工艺过程（activities）air test，通风试验backfilling hole，封孔flushing test，通水试验joint washing，洗缝seal，密封soak，浸泡water pressure test，压水试验管路及组件（circuit and elements）air supply，风包arising pipe，升浆管circuit，回路clamp，卡子cock，旋塞coil，蛇行管cylinder，缸套double nipple，对丝连接套expansion coupling，伸缩节female-quick coupling，内丝块接头fixed clamp，死卡flow rate meter，流量计galvanized elbow，渡锌弯头grout cap，灌浆帽grout cell，出浆盒grout stop plate，止浆片grout valve，灌浆阀inlet pipe，进浆管large radius elbow，大弧弯头main pipe，总管male-quick coupling，外丝块接头outlet pipe，出浆管packer，灌浆塞piston，活塞plug，堵头reducer socket，变径管套return pipe，回浆管tee piece，三通管reducer tee piece，变径三通管swivel-clamp，转卡u-bend，U弯头union，活接头ventilation pipe，排气管water supply，水包参数及指标（parameter and indexes）consistency，稠度fineness，细度。