BD330说明书

合集下载

330kv变电所说明书

目录前言 (1)第一章电气主接线的设计 (3)第二章变电所所接线和变压器选择 (9)第三章短路电流计算 (10)第四章电气设备和导线的选择 (11)第五章仪表及继电保护规划 (16)第六章变电所防雷保护设计 (18)第七章变电所配电装置 (24)参考文献 (25)附图：变电所电气主接线图330kV间隔断面图毕业设计计算书第一章电气主接线的设计我国330~500KV超高压配电装置采用的接线有：双母线分段、带旁路母线（或带旁路隔离开关）接线、一台半断路器接线、变压器母线接线和3~5角形接线。

一、330KV侧的接线选择330KV超高压配电装置，连接着大容量的发电厂、变电所和超高压输电线路，要求供电可靠、调度灵活，同时应满足运行检修方便，投资及占地较小等。

首先要满足可靠性准则的要求，设计主接线时应从以下方面考虑：(1)在保证安全可靠、运行灵活方面，即使不进行可靠性定量分析，也会想到运用双重连接这一基本准则。

即每一个回路应以多于一台短路器的可能与母线或相邻元件连接。

简单的单一连接不能用。

(2)为避免变电所全停或半全停事故的发生，普通的双母线带旁路的接线不能用。

(3)为维持系统的稳定性，易将故障的停电范围限制到最小，最好是一回线故障只停该回线，这就要求将母线分割，变成若干小段母线，显然要增加短路器的数量。

(4)对于超高压配电装置，主接线尚应适当考虑满足符合故障的能力，即一台设备检修，其他元件故障，停电范围不应超过全部元件的一半。

(5)断路器是超高压配电装置中比较昂贵的设备，从节省投资考虑，应合理配置使用。

综合以上因素，对于2回出线2台主变压器共4个元件的配置，有以下3种接线方案可供选择。

1.方案一：变压器—母线组接线这种接线的特点是:(1)出线采用双断路，保证高度可靠性，但当线路较多时，出线可采用一台半断路器。

(2)选择质量可靠的主变压器，直接将主变压器经隔离开关连接到母线上以节省断路器。

(3)调度灵活，电源和负荷可自由调配，安全可靠，有利于扩建。

CSC-330B数字式电抗器保护装置说明书

CSC-330B 数字式电抗器保护装置
说明书
Байду номын сангаас
目录
第 1 篇装置的技术说明...............................................................................................................1 1 概述............................................................................................................................................1
编制：苏毅邹东霞校核：张玲华标准化审查：梁路辉审定：宋小舟
出版号：V1.00 文件代号： F0SF.450.073 出版日期： 2011 年 4 月
版权所有：北京四方继保自动化股份有限公司
注：本公司保留对此说明书修改的权利。如果装置与说明书有不符之处，请您及时和
根据需要装置可保存故障处理过程中任何运行的中间结果结合cspc后台分析软件可以对保护动作行为作出跳闸结果静态特性分析并可以看到故障动态发展过程中保护行为的演化过程使得保护动作过程一目了然彻底消除了保护装置不明原因的误动作
CSC-330B 数字式电抗器保护装置说明书
（BD2010028）
CSC-330B 数字式电抗器保护装置说明书
2) 请仔细阅读本说明书，并按照说明书的规定调整、测试和操作。如有随机资料，请以随机资料为准。
3) 为防止装置损坏，严禁带电插拔装置各插件、触摸印制电路板上的芯片和器件。

MOBOTIX MOVE SD-330 安装指南说明书

SpeedDome SD-330This guide is for quick installing and connecting the MOBOTIX MOVE SD-330 Network PTZ Camera. You can find detailed information on the installation and connections in the Camera Manual (PDF, available on > Support > Download Center > Documentation > Manuals).Camera’s Connectors*Please contact the manufacturer for the compatible BNC cable.**Do NOT connect external power supply to the alarm I/O connector of the camera.NOTE: To purchase power adaptor, please contact the camera manufacturer for further information. NOTE: DC12V power jack and AC24V power connector cannot be used at the same time in case of unexpected damage. NOTE: It is not recommended to record with the SD card for 24/7 continuously, as it may not be able to support long term continuous data read/write. Please contact the manufacturer of the SD card for information regarding the reliability and the life expectancy.Power ConnectionTo power up the camera, connect the DC12V or AC24V power adaptor to the power connector of the camera and thepower outlet. Refer to the diagram and pin definition below for AC24V power connection.Alternatively, users can use an Ethernet cable and connect it to theRJ-45 port of the camera and a PoE+ switch (Class 4).Zero Downtime Power Switching (ZDT)When users connect DC12V power jack and the RJ-45 port at the same time, the power input comes from the DC12V connector. If the DC12V power source fails, the camera will switch power input seamlessly to the RJ-45 port until the DC12V power source is restored.Ethernet Cable ConnectionConnect one end of the Ethernet cable to the RJ-45 connector of the camera, and plug the other end of the cable to the network switch or PC.NOTE: In some cases, Ethernet crossover cable might be needed when connecting the camera directly to the PC. NOTE: Check the status of the link indicator and activity indicator LEDs. If the LEDs are unlit, please check the LAN connection.Green Link Light indicates good network connection.Orange Activity Light flashes for networkactivity indication.NOTE:The ITE is to be connected only to PoE networks without oute plant or equivalent description.Audio/AIarm I/O & RS485 ConnectionPlease refer to the diagram and pin definition tables below for audio/alarm I/O & RS485 connection.Camera Installation NoticeNOTE: For safety concern, it is recommended to hook up the camera with the anti-drop chain of the pendant when installing the camera. For more information about pendant and anti-drop chain, please contact the camera manufacturer.SpeedDome SD-330EN_02/2020MOBOTIXAG•Kaiserstrasse•D-67722Langmeil•Tel.:+4963029816-0•Fax:+4963029816-190•*****************• MOBOTIX, the MX Logo, MxControlCenter, MxEasy, MxPEG and MxActivitySensor are trademarks of MOBOTIX AG registered in the European Union, the U.S.A. and in other countries • For a complete product overview and a current price list, see the MOBOTIX website • Sold only to distributors or commercial clients • Subject to change without notice • MOBOTIX do not assume any liability for technical or editorial errors or omissions contained herein • All rights reserved • © MOBOTIX AG, 2018Before Login to the Camera A client program will be automatically installed to the PC when connecting to the camera. Before logging in to the camera, please ensure downloading the ActiveX control is allowed by either changing the ActiveX controls andplug-ins or setting Internet’s security level to default. For further details, please refer to the User’s Manual.NOTE : For the system requirement of the web browser, it is required to connect the camera with Microsoft Internet Explorer 10.0 or later version to ensure smooth operation.Camera LoginThe default IP address of the camera is: 10.x.x.x. By default, the camera starts as a DHCP client and automat-ically tries to get an IP address from a DHCP server.Login ID & Password Key in the camera’s IP address in the URL bar of the web browser window and hit “Enter”. Enter the default username (admin ) and password (meinsm ) in the prompt request dialogue. The password must be changed upon the first login.Install the ActiveX Control After connecting to the camera, the request for installing the ActiveX control will appear just below the URL bar. Right click on the information bar and click on <Install ActiveX Control…> to permit ActiveX control instal-lation. In the pop-up security warning window, click on <Install> to start downloading DCViewer software on the PC. Click on <Finish> after DCViewer installation is completed.。

GTD-330 BSW 说明书 1502010147A II 20151031通道升级

如果你还有其它有关于如何安全操作设备问题，请联系我公司技术人员或拨打服务线。
（4）
3、包装运输
3.1 运输保护锁
为了运输安全，灯具在水平/垂直旋转轴各设有保护锁；水平轴共有4个锁位点,锁扣位置在灯具水平轴行程四个方向的中心点。垂直轴共有3个锁位点, 锁扣位置在灯具垂直轴行程左中右方向。
3.2 拆卸包装
（3）
1.3 灯具包装附件
名称
数量
用户使用说明书
1
灯钩
2
安全保险绳
1
信号线
1
单位本套条条
备注 5 米，带公母插头
2、安全警告信息
本产品属于专业用途，不适用于其它。收到灯具后,请检查包装是否完整，并拆包检查设备是否有因运输而导致的损坏。如出
现运输而导致的损坏，请不要使用此灯具，并尽快与当地技术人员或厂家联系。
生裂缝和深痕时应更换。
悬挂灯具时，必须验证悬挂设备要能承受灯具的10倍以上重量。安装完毕后要验证灯盖及安装扣锁牢固并无损伤，同时使用安全保险绳作为灯具的辅助安全，固定在桁架上。
必须是专业人员方可进行灯具的安装、操作和维修，并严格遵守操作说明书所陈述规程操作。
眼睛不能长时间正视灯头。在安装前，请确认所使用的电源电压和灯具所标识的电压相符。应将每一台灯具正确接
2、安全警告信息 ..................................................................................................................... 4 3、包装运输
3.1 运输保护锁.....................................................................................................................5 3.2 拆卸包装.........................................................................................................................5 3.3 设备包装.........................................................................................................................5 4、安装要求说明 4.1 灯钩安装..........................................................................................................................5 4.2 设备安装.........................................................................................................................5 4.3 灯泡安装.........................................................................................................................6 5、电源、信号连接 5.1 电源连接.........................................................................................................................7 5.2 信号连接.........................................................................................................................7 5.3 设备状态检验.................................................................................................................7 6、控制面板 6.1 面板介绍.........................................................................................................................8 6.2 功能菜单操作.................................................................................................................8 7、设备主要技术参数 ........................................................................................................... 10 8、图案、颜色说明 8.1 图案...............................................................................................................................12 8.2 颜色...............................................................................................................................12 9、DMX 控制通道表 .............................................................................................................. 10 10、控制线路图 ..................................................................................................................... 17 11、常规维护 11.1 清洁与保养.................................................................................................................18 11.2 故障分析处理..............................................................................................................18 12、常用备件物料清单 ......................................................................................................... 19 敬告:

FP-DI-330操作说明书

亮点1．8个数字输入通道2．通用输入，工作电压自5V TTL至250VDC/VAC3．源，耗，或电源感应应用兼容4．开关LED指示5．3000V输入输出隔离6．250V安全工作电压双隔离7．工作温度范围：-40℃至+70℃下概述FP-DI-330 是FieldPoint的带有8个通用数字输入的数字输入模块，FP-DI-330可用于耗，源，或电源感应应用，兼容电压从5V至250VDC/VAC。

热拔插性能，安全隔离，通用输入范围，以及开关状态指示确保安装和维护极为方便。

通过本资料可了解FP-DI-330的安装，性能和特性。

更多有关通过网络设置和访问FP-DI-330的信息，请阅读与FP-DI-330一起使用的FieldPoint 网络模块的用户手册。

模块安装FP-DI-330是安装在FieldPoint 端子底板（FP-TB-XX）上的。

因为具有热拔插性能，可以把FP-DI-330装到带电的端子底板上，而不影响其它模块和端子底板的运行。

FP-DI-330从端子底板上接受工作电源。

请参照图1，按如下步骤安装FP-DI-330：1．把端子底板键滑动至X位置（用于任何模块）或3位置（用于FP-DI-330模块）。

2．把FP-DI-330的定位槽对准端子底板的导向轨。

3．把FP-DI-330按压进端子底板。

当模块固定到位时，端子底板的锁钩锁到位。

现场接线端子底板供给每个输入通道以及现场装置外部供电的连接。

每个通道可接为使用源或耗输出设备，或感应电源是否加到负载上。

图2显示这些基本接法的例子。

通过连至端子底板的V和C把外部电源接给现场设备。

每个通道都有两个输入端子，Ina和INb，一个公共端，COM (内部连至C端子)；和一个电源端子Vsup（内部连至V端子）。

表1列出每个通道信号的端子分配。

通用输入电路FP-DI-330的通用输入由带限流短路的双向光电隔离器组成。

每个通道有两个信号输入端，Ina和INb，可以互换。

海尔 BD-330WEPTU1 330升立式冷冻柜使用说明书

BD-328WL BD-330WEPTU1BD-328WEDTU1BD-332WGHS9B8U1智能家电操控智慧场景定制智家商城购物家电报装报修型号准备使用安全注意事项若电压波动范围较大（超过187~242V 的范围），须加装1000W 以上的自动稳压器配合使用。

使用220V/50Hz 交流电源在任何情况下,切勿切除或拆除电源插头的第三插脚（接地）。

电源插头应保持与插座牢固接触，否则可能导致火灾。

冷柜安装就位后，插头应在容易被够到的地方，以保证发生意外时可以及时拔下冷柜插头。

使用三眼插座切勿损坏电源线不要让箱体压住电源线或人为踩踏电源线。

将冷柜移离墙壁时，请小心谨慎，切勿滚压或损坏电源线。

必须拔下电源插头清洁、维修及更换损坏的LED 灯时，必须拔下冷柜的电源插头，以防触电。

必须到厂家指定的维修点或请专业的人员维修。

如果电源软线损坏，为了避免危险，必须由制造商、其维修部或类似部门的专业人员更换。

停电或清洁时，应拔下电源插头，至少保持间隔五分钟，才能再次接通电源，坏。

以防因压缩机连续启动而损远离易燃物在冷柜附近，切勿存放或使用汽油等易燃物品，以免引起火灾。

冷柜内禁止储存易燃、易爆物及强腐蚀性的酸、碱等。

切勿用作储藏食品以外用途本产品为家用冷柜，按国家标准的规定，只适用于储藏食品，不能用于其他用途，物制品等。

注意防水不要用水喷淋、冲洗冷柜，也不要放置在潮湿、易溅上水的地方，以免影响其电气绝缘性能。

气体泄漏时关闭气体泄漏的阀门，打开门窗；不要插、拔冷柜等电器件的电源插头。

不要在冷柜顶部放置不稳定的物品（重物、有水的容器），以免掉下伤人或溢水导致漏电。

为保证安全，请不要在冷柜顶部放置电源插座、稳压电源、微波炉等电器。

除了制造商推荐使用的类型外，不得在器具的食品储藏室使用电器。

严禁改造冷柜不得损坏制冷回路。

严禁私自拆卸、改造冷柜。

维修必须由专业人员进行。

注意看护儿童避免儿童吊在门体上玩耍，以免门体倾斜或冷柜倾倒造成人身伤害。

东芝330部分调试资料

东芝330部分调试资料前言本使用说明书，就在进行无机房电梯SPACEL-UNI(CV300系列)控制装置（系统）的安装·保养·调整作业所必要的处理方法上进行了说明。

本说明书的内容的适用对象为具有控制系统基本知识的技术以及管理人员。

在实施各种作业时，必须事先熟读该说明书，根据上面记载的指示进行操作。

禁止进行说明书上记载内容以外的行为·操作。

请妥善保管好该说明书，谨请彻底管理。

控制系统操作时的注意事项系统调整程序书：６Ｅ１Ｍ１８３６试运转程序书：６Ｅ１Ｍ１８３７高速调整程序书：６Ｅ１Ｍ１８３８乘感调整程序书：６Ｅ１Ｍ１８３９故障判断?错误代号：６Ｅ１Ｍ１１９５调整维保指示书：６Ｅ１Ｍ１８４０安全上的注意事项为了防止对管理和使用者及他人造成危害和财产的损害与未然，安全正确地使用商品。

在装置的本体以及其使用说明书上，记载有重要的内容。

请将以下内容（表示·图记号）充分理解后，再阅读本文，并遵守其记载事项。

[表示的说明]※：所说的受伤是指不需要住院治疗或定期去医院看病的伤、烧伤、触电等。

[图记号的说明][本体警告表示标签的确认]一般禁止·注意事项为了维护制品·利用者·作业者的安全性，将作业时的注意事项例举于以下。

请掌握和遵守其内容。

电梯系统的不适当操作·作业是导致故障，坏损，灾害的起因。

万一实施本说明书上记载的内容之外的行为，禁止的操作等，造成直接或间接的故障的场合，本公司将不负此责任，谨请谅解。

１）在电梯控制盘上贴有PL 标签（制品安全标签）。

禁止进行违反PL 标签指示的事。

必须按照指示进行作业。

２）没有指示禁止改造电梯控制盘。

将成为装置的误操作·发热·起火等的起因，有时也会给作业者自身带来危险。

３）在交换零部件之际，禁止纯正部件以外的使用（流用）。

必须使用指定用品。

４）在电梯控制盘方面，对于使用于调整保养的必要开关部以外的盘内部件，由于电源处于投入状态，因此禁止任意接触。

明基DS330投影机说明书

DS330Big projectionBright projection – 2800 ANSI LumensSVGA resolution, 13,000:1 contrast ratio, HDMI inputLow ownership costs - up to 10,000 hours² lamp lifeLightweight and portableDS330Ideal for use in a meeting room or classroom, the DS330 has a bright 2800L and 13,000:1 contrast allowing you to project bright, crystal clear images with superb colours using DLP® and BrilliantColor™ technologies. Incredible lamp life of up to 10,000 hours combined with Eco+technology provides energy and money saving features. Installed or on the move, the versatile DS330 incorporates HDMI, built in speaker, Full 3D technology and optional wireless capabilities that are easy to use.Eco + technology from Optoma increases our commitment to reducing the impact we all make on the environmentBright ImagesProject in ambient light conditions with the ultra bright 2800 ANSI Lumens. Ideal for meeting rooms and classrooms.Cost Saving – Long Lamp LifeReduce the number of lamp changes with lamp life of up to 10,000hours² using the Education Cycle.Clear, Focused ImagesProduce a stunning 13,000:1 contrast ratio for pin sharp graphics and crystal clear text using the unique Dynamic mode feature.Combined with DarkChip3 technology for Texas Instruments,Dynamic mode automatically adjusts the lamp output, based on the brightness information of each frame; to create a stunning high contrast ratio. Bright scenes are crisp and clear, while dark scenes remain detailed with deep blacks which gives exceptional light and shade detail.Green SolutionsEco + ModeSaving energy saves money! Eco + technology reduces the power consumption to as little as 30%. This intelligent feature can more than double your expected lamp life, lowering the total cost of ownership and reducing maintenance.Lamp ModeBrightDynamic Eco+Education CycleLamp Life (Hours)Eco AV mute off100% power consumption Eco AV mute on25% power consumptionWe know that improving our products is the best way to reduce our impact on the environment. That's why at Optoma we design our products to have a long usable life, use fewer materials, ship with the minimum packaging and be free of all possible toxic substances. Naturally,energy efficiency and being recyclable are built in at the design stage. With each new product, we strive towards minimising our environmental impact.Auto Power OffThere may be instances when the projector is left running when not in use. To help save energy if the projector is left running and no source is detected, the "Auto Power Off" feature automatically turns off the projector after a set period of time.Eco AV MuteStay in control of your presentation with the Eco AV mute feature.Direct your audience's attention away from the screen by blanking the image when no longer needed. This also instantly reduces the power consumption to 25%, further prolonging the life of your lamp.RS232 Compatibility - The DS330 comes with an extensive RS232 command set making it simple and easy to control with any control system. AMX Compatibility - DynamicDiscovery Protocol is incorporated into theDS330. This feature allows for easy installation with AMX control systems.We are so confident that the DS330 image colour quality will remain as good as the day you bought it that we will guarantee it for five years.The DS330 incorporates BrilliantColor™ multi-colour processing technology to bring stunning, vibrant colour to your screen. Using six separate primary and secondary colours to produce a new level of colour performance and control; BrilliantColor™increases colour brightness by up to 50% over other technologies to create accurate true to life images.Audio CapabilityBuilt-in 2W speaker offers excellent audio support. The DS330 is easy to set up without the need for costly external speakers.ControlAmazing ColoursThe DS330 incorporates BrilliantColor™ technology to produce stunningly bright images with perfectly balanced life-like colours.Colour GuaranteeBrilliantColor™Rapid OffIt takes less than 10 seconds for the projector to power up and shutdown, saving both time and energy.Quick ResumeSave time by not waiting for the projector to cool down before it can power up again. If the projector is accidentally turned off, this feature allows the projector to be instantly powered on again, if selected within a period of 100 seconds.Using the inherent speed of DLP technology,The Optoma DS330. Full 3D projector can display true 3D content form any 3D display device, such as 3D Blu-ray, PS3, Xbox and Sky3D.Easy Lamp ReplacementTop loading lamp cover allows easy access to replace lamps without having to remove the projector from the mount.Full 3D ReadyRemote MouseKeep your audience’s attention focussed on the right things using the simple, yet powerful remote with USB mouse control.Wireless Presenting (optional extra)Making presentations couldn't be easier using the optional wireless features of the DS330. Using the Wireless Adapter (sold separately)you can connect and display presentations and video material wirelessly from a laptop, PC or mobile device. (Additional power required)Specification TableDisplay Technology Single 0.55” SVGA DC3 DMD chip DLP® Technology by Texas InstrumentsNative Resolution SVGA 800 x 600Brightness - BRIGHT mode12800 ANSI LumensContrast13,000:1Noise Level26dB (min)Weight 2.21 kgI/O Connectors Inputs:HDMI (v1.4a 3D), 2 x 15 Pin D-sub (RGB/YPbPr), S-Video, Composite, Audio In, USB (remote mouse)Outputs:15 Pin D-sub, Audio OutControl:RS232 - 9 PinPreset Mode PC:For computer or notebook (Brightest image)Movie:Maximum contrast and Colour accuracyGame:Bright vivid coloursRGB:For Standard PC Colour (Best Colour Reproductiion)User:Memorises user's settingsMaximum Resolution UXGA 1600 x 1200Computer Compatibility UXGA, SXGA, XGA, SVGA, VGA, MacVideo Compatibility PAL (B, D, G, H, I, M, N, 576i/p), NTSC (M, 4.43/3.58 MHz, 480i/p), SECAM (B, D, G, K, K1, L) HD (1080i, 720p) Displayable Colours1073.4 MillionProjection Lens F/2.51~2.69; f=21.95~24.18mm, 1.1x Manual ZoomThrow Ratio 1.97 - 2.17:1Projection Screen Size0.69m – 7.62m (27.24” - 300.04”) Diagonal 4:3Projection Distance 1.2 - 12 metresHorizontal Scan Rate15.3 - 91.1kHzVertical Scan Rate24 - 85HzLamp Type/Lamp Life2190W, 10,000 hours² (Education Cycle) 6500/6000/5000 hours (Eco+/Dynamic/BRIGHT mode)Keystone Correction± 40° VerticalAudio2WDimensions (W x D x H)316 x 224 x 124mmRemote Control Full function remote with remote mouse and direct source selectingPower Supply100-240V, 50-60HzPower Consumption234W BRIGHT mode < 0.5W Standby mode, 202W Eco+ mode < 0.5W Standby modeOperating Conditions5°C - 40°C, Max. Humidity 85%, Max. Altitude 3000mUniformity85%Security Security Bar, Kensington Lock, Password ProtectionStandard Accessories AC Power Cord, VGA Cable, Infra Red Remote Control with Batteries, Quick Start Card, CD User Manual, Warranty Card Optional Accessories Ceiling Mount KitRoHS Compliant3D Support The 3D features of Optoma projectors can only be used with compatible 3D content. Typical applications include use with 3Deducational or 3D design and modelling systems. 3D TV broadcast systems, (SKY in the UK), Blu-ray 3D™ and 3D gamesfrom the Sony® PS3 or Microsoft® Xbox 360 are now supported as part of the HDMI v1.4a specification.3D Viewing Requires the Optoma DLP-Link shutterglasses - available separately.3D Compatibility Side-by-Side:1080i50 / 60, 720p50 / 60Frame-pack: 1080p24, 720p50 / 60Over-Under: 1080p24, 720p50 / 60Offset115%DS330 Remote Control 1. Power2. Mouse select3. Source4. Re-sync5. Left mouse click6. Right mouse click7. Mouse control8. Display mode9. Page up/down control 10. Vertical keystonecorrection11. Volume control 12. Brightness 13. Menu14. Direct input source select 15. Eco AV mute 16. Eco+17. 3D controlEasy To Use RemoteDS330 Connections18. Audio In (VGA)19. S-Video 20. VGA 121. VGA Out 22. HDMI 23. RS23224. USB (Remote Mouse)25. Audio In (S-Video/Video)26. KensingtonTM Lock 27. Audio Out 28. Video 29. VGA 2Exceptional Connectivity / Multiple TerminalsProjection Distance 1.2 - 12m (4:3 Aspect Ratio)Projection Distance (m)Max. Horizontal Image Size (m)Min. Horizontal Image Size (m)Max. Vertical Image Size (m)Min. Vertical Image Size (m)Min Diagonal Image Size (m)Max Diagonal Image Size (m)Min Diagonal Image Size (inch)Max Diagonal Image Size (inch)Max. Image Offset (m)1.200.610.550.460.420.690.7627.2430.000.072.00 1.020.920.760.69 1.15 1.2745.4050.010.112.50 1.27 1.150.950.87 1.44 1.5956.7562.510.143.00 1.52 1.38 1.14 1.04 1.73 1.9168.1075.010.174.00 2.03 1.84 1.53 1.39 2.31 2.5490.80100.010.235.00 2.54 2.30 1.91 1.73 2.88 3.18113.50125.020.296.00 3.05 2.76 2.29 2.08 3.46 3.81136.19150.020.347.00 3.55 3.23 2.67 2.43 4.04 4.45158.89175.030.408.00 4.06 3.69 3.05 2.77 4.61 5.08181.59200.030.469.00 4.57 4.15 3.43 3.12 5.19 5.72204.29225.030.5210.00 5.08 4.61 3.82 3.46 5.77 6.35226.99250.040.5711.00 5.58 5.07 4.20 3.81 6.34 6.99249.69275.040.6312.006.095.534.584.166.927.62272.39300.040.69Optoma Europe Ltd.42 Caxton Way, Watford Business Park, Watford, Hertfordshire, UK. WD18 8QZ1Brightness and lamp lifetime will vary depending on the selected projector mode, environmental conditions and usage. As is common with all lamp based projectors, brightness will decrease over the lamp lifetime. 2Typical lamp life achieved through testing and will vary according to operational use and environmental conditions. 10,000 hours lamp life is based on a daily cycle that reflects projector usage in a typical education environment. Details of this cycle are available on request. 3Optoma guarantees that in normal use, Optoma DLP® colour quality will be indistinguishable from when new. Exclusions: (a) Guarantee is voided if the projector is subject to damage through misuse. (b) Guarantee may be void in industrial or commercial entertainment environments where dust or smoke is excessive (c) Guarantee will not apply if lamp brightness is below 50% due to wear or if the projector is not working due to other faults.(d) Over time worn lamps within all projector types will show a slight colour variance. Copyright © 2013, Optoma Europe Ltd. All other product names and company names used herein are for identification purposes only and may be trademarks or registered trademarks of their respective owners. Errors and omissions excepted, all specifications are subject to change without notice. DLP®, BrilliantColor™ and the DLP logo are registered trademarks of Texas Instruments. All images of products are for representation purposes only. Whilst every care is taken to provide accurate images of our products, actual products may differ slightly. Some product images may have been digitally altered by us to add an Optoma logo to the front panel. Optoma reserves the right to amend or alter actual product, product specifications or product images without notice. Some images may be simulated.14/02/2013 11:56。

Canon DC330 DVD摄像机说明书

O P重要使用说明2如何选择DVD光盘有各种类型的DVD光盘，但该摄像机仅使用以下三类8cm DVD光盘：DVD-R、DVD-R DL和DVD-RW。

了解其差异并选择最符合您需求的光盘。

DVD-R最佳兼容性3使用DVD的优点无需担心记录会覆盖磁带内容。

使用DVD时，摄像机会在光盘的空白空间中自动记录。

因此不必担心记录会错误地覆盖以前的记忆。

4按所用DVD光盘确定的可用功能5目录简介 _____________________________________26插入和取出存储卡28选择记录模式29变焦:光学、优化和数码变焦30快速启动功能31查看和删除最后记录的场景6 • 目录31基本播放31播放视频33删除场景33屏幕显示（数据码）34其他功能48查看照片49播放时放大照片50删除照片51其他功能51连续拍摄和包围曝光（驱动模式）52自动对焦优先53直方图和其他屏幕显示53保护照片54初始化存储卡目录 • 755打印照片55打印照片 - 直接打印55选择打印设置57打印指定76使用注意事项78维修/其他79在国外使用摄像机80信息概览80系统概览81可选附件84规格87索引8 • 目录关于本说明书感谢您购买佳能DC330。

使用本摄像机之前，请先详细阅读本说明书，并妥善保存说明书作日后参考。

如果您的摄像机工作不正常，请参考故障排除70)。

本说明书使用的约定简介 • 9了解摄像机附件10 • 简介部件指南简介 • 1112 • 简介无线遥控器WL-D86简介 • 13屏幕显示播放视频图像（播放过程中）C O14 • 简介记录静止图像查看静止图像C O简介 • 1516 • 简介准备工作• 17准备工作本章介绍基本操作（如菜单导航）和初次设置，以帮助您了解更多有关摄像机的知识。

哒一声安装到位为止。

耗电池电量。

1从摄像机上断开小型电源转接器。

2从电源插座及小型电源转接器上拔下电源线。

待电池充满电后准备无线遥控器和附件使用无线遥控器首先，将附带的CR2025锂钮扣电池插入无线遥控器。

SPEED-BLOC 模型330电动沙机操作手册说明书

IMPORTANTPlease make certain that the person who is to use this equipment carefully reads and understands these instructions before starting operations.Double Insulated SPEED-BLOC ®Finishing SanderMODEL 330Some dust created by power sanding, sawing, grinding, drilling,and other construction activities contains chemicals known (to theState of California) to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:●lead from lead-based paints●crystalline silica from bricks and cement and other masonry products ●arsenic and chromium from chemically-treated lumberYour risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, always wear NIOSH/OSHA approved, properly fitting face mask or respirator when using such tools.indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.indicates a potentially hazardous situation which, if not avoided,could result in death or serious injury.indicates a potentially hazardous situation which, if not avoided,may result in minor or moderate injury.used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may result inproperty damage.CALIFORNIA PROPOSITION 65It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information.GENERAL SAFETY RULESRead all instructions. Failure to follow allinstructions listed below may result in electric shock, fire and/orserious injury. The term "power tool" in all of the warnings listedbelow refers to your mains-operated (corded) power tool orbattery-operated (cordless) power tool.SAVE THESE INSTRUCTIONS1)Work area safetya)Keep work area clean and well lit. Cluttered or dark areas inviteaccidents.b)Do not operate power tools in explosive atmospheres, such as in thepresence of flammable liquids, gases or dust.Power tools createsparks which may ignite the dust or fumes.c)Keep children and bystanders away while operating a power tool.Distractions can cause you to lose control.2)Electrical safetya)Power tool plugs must match the outlet. Never modify the plug in anyway. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electricshock.b)Avoid body contact with earthed or grounded surfaces such aspipes, radiators, ranges and refrigerators.There is an increased risk of electric shock if your body is earthed or grounded.c)Do not expose power tools to rain or wet conditions.Water entering apower tool will increase the risk of electric shock.d)Do not abuse the cord. Never use the cord for carrying, pulling orunplugging the power tool. Keep cord away from heat, oil, sharpedges or moving parts. Damaged or entangled cords increase the riskof electric shock.e)When operating a power tool outdoors, use an extension cordsuitable for outdoor e of a cord suitable for outdoor use reduces the risk of electric shock.3)Personal safetya)Stay alert, watch what you are doing and use common sense whenoperating a power tool. Do not use a power tool while you are tiredor under the influence of drugs, alcohol or medication.A moment of inattention while operating power tools may result in serious personalinjury.b)Use safety equipment. Always wear eye protection.Safety equipmentsuch as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.c)Avoid accidental starting. Ensure the switch is in the off-positionbefore plugging in. Carrying power tools with your finger on the switchor plugging in power tools that have the switch on invites accidents.d)Remove any adjusting key or wrench before turning the power toolon.A wrench or a key left attached to a rotating part of the power toolmay result in personal injury.e)Do not overreach. Keep proper footing and balance at all times.Thisenables better control of the power tool in unexpected situations.f)Dress properly. Do not wear loose clothing or jewelry. Keep yourhair, clothing and gloves away from moving parts.Loose clothes,jewelry or long hair can be caught in moving parts.g)If devices are provided for the connection of dust extraction andcollection facilities, ensure these are connected and properly used.Use of these devices can reduce dust-related hazards.4)Power tool use and carea)Do not force the power tool. Use the correct power tool for yourapplication.The correct power tool will do the job better and safer at the rate for which it was designed.b)Do not use the power tool if the switch does not turn it on and off.Any power tool that cannot be controlled with the switch is dangerousand must be repaired.c)Disconnect the plug from the power source before making anyadjustments, changing accessories, or storing power tools.Such preventive safety measures reduce the risk of starting the power tool accidentally.d)Store idle power tools out of the reach of children and do not allowpersons unfamiliar with the power tool or these instructions tooperate the power tool. Power tools are dangerous in the hands ofuntrained users.e)Maintain power tools. Check for misalignment or binding of movingparts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repairedbefore use.Many accidents are caused by poorly maintained powertools.f)Keep cutting tools sharp and clean.Properly maintained cutting toolswith sharp cutting edges are less likely to bind and are easier to control.g)Use the power tool, accessories and tool bits etc., in accordancewith these instructions and in the manner intended for theparticular type of power tool, taking into account the workingconditions and the work to be e of the power tool foroperations different from those intended could result in a hazardoussituation.5)Servicea)Have your power tool serviced by a qualified repair person using onlyidentical replacement parts.This will ensure that the safety of thepower tool is maintained.1.Hold power tools by insulated gripping surfaces when performing anoperation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator.2.Always disconnect the sander cord plug from the power circuit beforechanging abrasive sheets. Such preventive safety measures reduce the risk of starting the power tool accidentally.e proper safety equipment.Wear safety goggles to protect your eyesand wear a protective mask to minimize breathing in the fine dust created while sanding.4.Sanding of lead-based paint is not recommend. Lead-based paint shouldonly be removed by a professional.5.Wear eye and hearing protection. Always use safety glasses. Everydayeyeglasses are NOT safety glasses. USE CERTIFIED SAFETY EQUIPMENT.Eye protection equipment should comply with ANSI Z87.1 standards.Hearing equipment should comply with ANSI S3.19 standards.e of this tool can generate and disburse dust or otherairborne particles, including wood dust, crystalline silica dust and asbestos dust. Direct particles away from face and body. Always operate tool in well ventilated area and provide for proper dust removal. Use dust collection system wherever possible. Exposure to the dust may cause serious and permanent respiratory or other injury, including silicosis (a serious lung disease), cancer, and death. Avoid breathing the dust, and avoid prolonged contact with dust. Allowing dust to get into your mouth or eyes, or lay on your skin may promote absorption of harmful material.Always use properly fitting NIOSH/OSHA approved respiratory protection appropriate for the dust exposure, and wash exposed areas with soap and water.SYMBOL DEFINITIONV........................voltsA........................amperesHz........................hertzW........................wattskW........................kilowattsF........................faradsµF........................microfaradsl........................litresg........................gramskg........................kilogramsbar........................barsPa........................pascalsh........................hoursmin........................minutess........................secondsn0........................no-load speed…/min or …min-1.........Revolutions or reciprocations per minuteor d.c. ................direct currentor a.c. ................alternating current2........................two-phase alternating current2N........................two-phase alternating current with neutral3........................three-phase alternating current3N........................three-phase alternating current with neutral........................rated current of the appropriate fuse-link in amperes........................time-lag miniature fuse-link where X is the symbolfor the time/current characteristic, as given in IEC 60127........................protective earth........................class II toolIPXX........................IP symbolExtreme care should be taken when removing paint. Thepeelings, residue, and vapors of paint may contain lead, whichis poisonous. Exposure to even low levels of lead can causeirreversible brain and nervous system damage. Young andunborn children are particularly vulnerable.Before beginning any paint removal process you should determine whether the paint you are removing contains lead. This can be done by your local health department or by a professional who uses a paint analyzer to check for lead. Lead-based paint should only be removed by a professional.Persons removing paint should follow these guidelines:1.Keep the work area well ventilated.Open the windows and put an exhaust fan in one of them. Be sure the fan is moving air from inside to outside.2.Remove or cover any carpets, rugs, furniture, clothing, cooking utensils, and air ducts.Such preventive safety measures reduce the risk of exposure.3.Place drop cloths in the work area to catch any paint chips or peelings. Wear protective clothing such as extra work shirts, overalls and hats.Such preventive safety measures reduce the risk of exposure.4.Work in one room at a time.Furnishings should be removed or placed in the center of the room and covered. Work areas should be sealed off from the rest of the dwelling by sealing doorways with drop cloths.5.Children, pregnant, or potentially pregnant women and nursing mothers should not be present in the work area until the work is done and all cleanup is complete.Such preventive safety measures reduce the risk of injury.6.Wear a dust respirator or a dual filter (dust and fume) respirator mask which has been approved by the Occupational Safety and Health Administration (OSHA), the National Institute of Safety and Health (NIOSH), or the United States Bureau of Mines.These masks and replaceable filters are readily available at major hardware stores. Be sure the mask fits. Beards and facial hair may keep the masks from sealing properly. Change filters often. DISPOSABLE PAPER MASKS ARE NOT ADEQUATE.7.Keep food and drink out of the work area.Wash hands, arms, and face and rinse mouth before eating or drinking. Do not smoke or chew gum or tobacco in the work area.8.Clean up all removed paint and dust by wet mopping the floors. Use a wet cloth to clean all walls, sills and any other surfaces where paint or dust is clinging. DO NOT SWEEP, DRY DUST OR VACUUM. Use a high phosphate detergent or trisodium (TSP) to wash and mop areas.9.At the end of each work session, put the paint chips and debris in a double plastic bag, close it with tape or twist ties and dispose properly.Such preventive safety measures reduce the risk of exposure.10.Remove protective clothing and work shoes in the work area to avoid carrying dust into the rest of the dwelling.Wash work clothes separately. Wipe shoes off with a wet rag, then wash that rag with the work clothes. Wash hair and body thoroughly with soap and water.SAVE THESE INSTRUCTIONS!MOTORMany Porter-Cable tools will operate on either D.C., or single phase 25 to 60 cycle A.C. current and voltage within plus or minus 5 percent of that shown on the specification plate on the tool. Several models, however, are designed for A.C. current only. Refer to the specification plate on your tool for proper voltage and current rating.Do not operate your tool on a current on which the voltage is notwithin correct limits. Do not operate tools rated A.C. only on D.C.current. To do so may seriously damage the tool.EXTENSION CORD SELECTIONIf an extension cord is used, make sure the conductor size is large enough to prevent excessive voltage drop which will cause loss of power and possible motor damage. A table of recommended extension cord sizes will be found in this section. This table is based on limiting line voltage drop to 5 volts (10 volts for 230 volts) at 150% of rated amperes.If an extension cord is to be used outdoors it must be marked with the suffix W-A or W following the cord type designation. For example – SJTW-A to indicate it is acceptable for outdoor use.SAVE THESE INSTRUCTIONS!FOREWORDYour Porter-Cable Finishing Sander is equipped to accept Stikit™ adhesive backed abrasives (41/2" width) or conventional abrasive sheets (41/2" x 51/2").This Sander is suitable for coarse, medium or fine sanding of wood, plaster, metal and plastics. It is ideal for leveling wallboard joints, finishing cabinets, rubbing and polishing furniture, fitting screens and doors and for general finishing work in the shop.NOTE:This tool is shipped completely assembled. No assembly time or tools are required.ABRASIVE ATTACHMENT TOOL IS REQUIRED- Wrench (furnished)SELECTING THE RIGHT ABRASIVE SHEETBy selecting the proper type of abrasive, the finest finishes can be attained. In general, coarser grit sizes will remove the most material and finer grit sizes will produce the best finishes.Naturally, in all sanding operations, best results will be obtained if you select the proper size and type of abrasives. Only garnet, aluminum oxide and silicon carbide are recommended for use with finishing sanders. Flint paper is not satisfactory for machine sanding, due to its weak structure.Before starting to work, make sure you have the right abrasive for the material on which the sander is to be used. Make sure you use the correct size abrasive paper or cloth. Cut, do not tear, the abrasive sheets to size.ATTACHING STIKIT™ ABRASIVEStikit™ abrasives (ten yard rolls) and a convenient dispenser are available from your Porter-Cable distributor.To install Stikit™ abrasive, cut a 41/8" long piece of abrasive from roll, align abrasive with sander pad and press in place as shown in Fig. 1.To remove, lift one corner of abrasive with fingernail and peel off. ATTACHING CONVENTIONAL ABRASIVEDisconnect tool from power source.1.Insert small end of wrench, furnished with sander, into slot (A), Fig. 2, with hump of the wrench in up position, and press wrench toward sander housing to open clamp.2.Slip one end of abrasive sheet under clamp, stretch sheet tight over pad, open rear clamp with wrench and slip free end of abrasive sheet under rear clamp.TO START AND STOP SANDERMake sure switch (A), Fig. 3, is in “OFF”position.1.Make sure power source voltage is the same as specified on the sander’s specification plate.2.Insert cord plug into power source outlet.3.While holding sander firmly and off of work surface, slide switch (A), Fig.3, to the “ON”position.4.Allow sander to reach full speed. Set it down on the work evenly andmove it slowly back and forth in wide overlapping arcs (see SANDING PROCEDURE section of this manual).5.When you are finished sanding, lift sander up off work and slide switch(A), Fig. 3, to the “OFF”position to stop sander.SANDING PROCEDUREThe Porter-Cable Finishing Sander has been designed for one-hand operation (Fig.3). Because it is light in weight, vibration-free and perfectly balanced, the sander can be easily guided over the work surface with one hand. The normal weight of the machine is sufficient for efficient sanding.Do not put additional pressure on the machine. This would only slow down the speed of the pad, reducing the sanding efficiency and put an additional burden on the motor. In addition, it might cause the sander to jump on the work. Let the sander do the work.OPERATIONFig. 1Fig. 2AFig. 3AFINE FINISHINGThe action of the Porter-Cable Finishing Sander causes thousands of tiny abrasive grits to move in circular orbits against the work at high speed. Each grain moves in the same direction at a constant speed so the cutting action is uniform over the entire pad surface. Crossing and re-crossing of the abrasive grits from all directions quickly levels surface irregularities to a fine, uniform smoothness. Start the work with an abrasive grit just coarse enough to remove the high spots and excessive roughness. Follow with a second sanding using a grit one or two grades finer. Continue with successively finer grits until the desired finish is obtained. DO NOT GO FROM A COARSE GRIT TO A VERY FINE GRIT IN ONE STEP.Going from a coarse grit to a very fine grit in one step could make it difficult to remove swirl marks that might have been made by the coarse grit abrasive. Use the finest grits practical for the roughing operation and then finish by using successively finer grits.REMOVING PAINT AND VARNISHRead and follow all instructions in the ADDITIONAL SAFETY RULES FOR PAINT REMOVAL section of this manual.Your sander will do a good job of removing old paint and varnish if two precautions are taken. First, be sure to use a coarse, open coat abrasive to avoid the usual clogging of the abrasive surfaces. Second keep the machine moving over new areas to avoid heating and softening the material being removed. Try to work the entire surface down at the same time by working in wide, overlapping arcs. Do not concentrate on small areas. If liquid removers or heaters are used to speed the work, be sure the surface is cool and dry and the excess material has been scraped away with a putty knife or other suitable scraping tool before applying the sander.CABINETS AND DOORSThe orbital motion of the Porter-Cable Finishing Sander is ideally suited for finishing doors, cabinet fronts and other installations where wood grain is often perpendicular to that of a joining piece. Since the motion is circular, the machine may be moved in any direction and crossed from one part to the other without regard to direction of grain. A uniform and smooth finish will result on both parts. The same procedure may be used when evening joints in all types of cabinet work. The sander may be worked on both sides and in all directions to obtain a smooth, matching joint. By properly changing from coarser to finer grit abrasives, an excellent finish will result.RUBBING AND POLISHINGThe finishing sander is excellent for all types of polishing and rubbing on flat or round surfaces. Felt rubbing pads, available as accessory equipment can be quickly attached for rubbing operations. With it, metal parts, enameled surfaces and woodwork may be polished. Use rouge or paste wax for polishing with the finishing sander.KEEP TOOL CLEANPeriodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material.Wear ANSI Z87.1 safety glasses while using compressed air.FAILURE TO STARTShould your tool fail to start, check to make sure the prongs on the cord plug are making good contact in the outlet. Also, check for blown fuses or open circuit breakers in the line.LUBRICATIONThis tool has been lubricated with a sufficient amount of high grade lubricant for the life of the unit under normal operating conditions. No further lubrication is necessary.BRUSH INSPECTION (If applicable)For your continued safety and electrical protection, brush inspection and replacement on this tool should ONLY be performed by an AUTHORIZED PORTER-CABLE SERVICE STATION or a PORTER-CABLE•DELTA FACTORY SERVICE CENTER.At approximately 100 hours of use, take or send your tool to your nearest authorized Porter-Cable Service Station to be thoroughly cleaned and inspected. Have worn parts replaced and lubricated with fresh lubricant. Have new brushes installed, and test the tool for performance.Any loss of power before the above maintenance check may indicate the need for immediate servicing of your tool. DO NOT CONTINUE TO OPERATE TOOL UNDER THIS CONDITION. If proper operating voltage is present, return your tool to the service station for immediate service.。

MD330 系列变频器使用说明书（张力控制专用变频器）

目录前言 (1)第一章概述 (4)第二章张力控制原理介绍 (6)2.1 典型收卷张力控制示意图 (6)2.2 张力控制方案介绍 (6)第三章功能参数表 (10)第四章参数说明 (16)4.1 控制模式选择部分 (16)4.2 张力设定部分 (17)4.3 卷径计算部分 (18)4.4 线速度输入部分 (20)4.5 张力补偿部分 (21)4.6 PID参数 (22)4.7 自动换卷参数 (22)4.8 增补部分参数 (23)附录 (27)附录版本变更记录 (27)第一章概述 MD330用户手册（张力控制专用变频器）第一章概述本手册需与《MD320用户手册》配合使用。

本手册仅介绍与卷曲张力控制有关的部分，其他的基本功能请参考《MD320用户手册》。

当张力控制模式选为无效时，变频器的功能与MD320完全相同。

MD330用于卷曲控制，可以自动计算卷径，在卷径变化时仍能够获得恒张力效果。

在没有卷径变化的场合实现恒转矩控制，建议使用MD320变频器。

选用张力控制模式后，变频器的输出频率和转矩由张力控制功能自动产生，F0组中频率源的选择将不起作用。

MD330用户手册（张力控制专用变频器）第二章张力控制原理介绍1）张力设定部分：用以设定张力，实际使用中张力的设定值应与所用材料、卷曲成型的要求等实际情况相对应，需由使用者设定。

张力锥度可以控制张力随卷径增加而递减，用于改善收卷成型的效果。

2）卷径计算部分：用于计算或获得卷径信息，如果用线速度计算卷径需用到线速度输入功能部分，如果用厚度累计计算卷径需用到厚度累计计算卷径相关参数功能部分。

3）转矩补偿部分：电机的输出转矩在加减速时有一部分要用来克服收（放）卷辊的转动惯量，变频器中关于惯量补偿部分可以通过适当的参数设置自动地根据加减速速率进行转矩补偿，使系统在加减速过程中仍获得稳定的张力。

摩擦补偿可以克服系统阻力对张力产生的影响。

3、闭环速度控制模式闭环是指需要张力（位置）检测反馈信号构成闭环调节，速度控制模式是指变频器根据反馈信号调节输出频率，而达到控制目的，速度模式变频器可工作在无速度传感器矢量控制、有速度传感器矢量控制和V/F控制三种方式中的任何一种。

Canon DC330 DC320 DC310 标准定义录像机指南说明书

Standard Definition CamcorderTimes to Remember on DVD•Get closer,get wider with Genuine Canon 48x (DC330/DC320),41x (DC310) Advanced Zoom•1.07 Megapixel CCD Image Sensor for sharp resolution (DC330/DC320)•True Widescreen HR recording that’s picture perfect •DIGIC DV II Image Processor for superior imaging and fast response•Soft LCD Video Light to illuminate dark scenes •Never miss a shot with the Quick Start Button •Activate camcorder functions from a distance with the Multi-Angle Remote Control (DC330)DC310DC320DC330DC330/320/310 KitOptional AccessoriesDVD-R DL54Strap (WS-20, SS-650, SS-600)Soft Carrying Case SC-2000DC330 kit contents shownBattery Pack(NB-2LH, BP-2L24H, BP-2L14)Car Battery Charger CBC-NB2Battery Charger CB-2LW Compact Power Adapter CA-570FormatDVD-VIDEO (VR)Recording Media DVD-R/-RW/-R DL, SDHCRecording TimeSingle Sided: 20 min. (XP), 30 min. (SP), 60 min. (LP)Double Sided: 40 min. (XP), 60 min. (SP), 120 min. (LP)Dual Layer Single Sided: 36 min. (XP), 54 min. (SP),108 min. (LP)Image Processor DIGIC DV IITotal PixelsDC330/DC320:Approx. 1.07 megapixel CCD DC310:Approx. 680,000 pixel CCD Image Sensor 1/6" CCDLensZoom Ratio: 37x Optical, 2000x DigitalAdvanced Zoom: 48x (16:9)/55x (4:3)(DC330/DC320)41x (16.9) (DC310)Focal Length: 2.6–96.2mmZoom Speed: variable 3, Fixed zoom speeds f/ Number: f/2.0 to 5.2Filter Size: No filter thread Image Stabilizer Electronic Image Stabilizer Minimum Focusing 10mm/1m (Wide/Tele)Distance Effective PixelsDC330/DC320:Movie: Advanced Zoom ON (16:9): approx. 0.71megapixels (Wide)/0.41 megapixels (Tele); Advanced Zoom OFF (16:9): approx. 0.55 megapixels; Still: approx. 0.8 megapixels;DC310:Movie: Advanced Zoom ON (16:9): approx. 0.45megapixels (Wide)/0.36 megapixels (Tele); Advanced Zoom OFF (16:9): approx. 0.36 megapixels; Still: approx. 0.45 megapixels Maximum Shutter SpeedMovie: 1/2000Still Image: 1/500LCD Screen 2.7" Widescreen LCD approx. 112,000 pixels Viewfinder 0.35" Widescreen Color EVF approx. 114,000 pixels AF System Though the lens, Manual Focusing possible Manual Exposure YesAE ModesEASY, P, Tv, Portrait, Sports, Night, Snow, Beach, (Movie/Still Image)Sunset, Spotlight, Fireworks White Balance Method Auto,Daylight, Tungsten Lux Rating 1.3 Lux (using Night Mode)AudioDolby Digital (2-channels)Still Image Recording 1152 x 864, 1152 x 648, 640 x 480USB Terminal (DC330 only)USB 2.0 Hi-Speed Microphone Terminal N/A Video Light LCD Built-in Lens Cover ManualDimensions (W x H x D)Approx. 2.6 x 3.5 x 5.0 in./66 x 90 x 126mm Weight (body only)Approx. 13.4 oz./380gSpecificationsSystem ChartAll images and effects simulated.Specifications and availability are subject to change without notice. Weight and dimensions are approximate. Canon and DIGIC are registered trademarks of Canon Inc. in the United States, and may also be registered trademarks or trademarks in other countries. IMAGEANYWARE is a trademark of Canon. Other names and products not mentioned above may be registered trademarks or trade-marks of their respective companies.Warning: Unauthorized recording of copyrighted materials may infringe on the rights of copyright owners and be contrary to copyright laws.Use of genuine Canon accessories is recommended: this product is designed to perform optimally when used with genuine Canon accessories.。

XP330 PLC、HMI integration User 说明书

XINJE Electronic Co., Ltd. XP330 PLC、HMI integration User manualWuxi XINJE Electronic Co., Ltd.CatalogChapter 1 Introduction of XP3301-1：Performance1-2：General specification1-3：Each part’s name1-4：Function and specification of HMI1-5：Function and input/output specification of PLC 1-6：Connection chart of program cable1-7：Size and installationChapter 2 HMI project screen’s editingChapter 3 PLC program and applicationChapter 1 Introduction of XP3301-1：Performance◆Gather logic control、analog input/output、HMI in one bodyDigital input：10 points / optical coupling insulationDigital output：8 points / relayAnalog disposal：XP-BD-2PT2AD、XP-BD-2TC2PID、XP-BD-4AD……Many BD modules can be collocated freely.HMI screen editing is simple and has strong function◆ LCD display：192×64 pixels（3.7inch）；LCD’s lift can reach 0.5 million hours◆ There are 26 function keys◆ The buttons are delicacy and precise◆ Program port is designed to have many functions：HMI and PLC use the same programcable when programming◆ Water-proof grade fits IP65◆ With compact structure，it saves large space of the electric-control tank◆ The appearance is simple and fashion1-2：General specification1：Electric specification2．Environment conditionOperate temperature 0~50℃Save temperature –10~60℃20~85%（No dew）EnvironmenttemperatureVibration resistance 10~25Hz(X,Y,Z direction 2G per 30 min)Resist interfere V oltage noise： 1000Vp-pAtmosphere No canker gasIP65FProtect configuration Fits1-3：Each part’s nameKey’s basic function tableKey Basic functionNo matter what status the display is, once press this key, it will go back tothe system’s initial screen. System’s initial screen is appointed when the user designs the screen (The defaulted value is No.1 screen). Generally, set the main menu or the screen which is used most frequently to be the initial screen. Turn the screen to the previous pageTurn the screen to the next pagePress this key to start modifying register’s value, the current register window which is being modifying will display in obverse color. Also the modifying bit displays glittering. If the current screen has no register set window component, carry on a no operation. Press [SET] key before [ENT], then the current modifying operation will be canceled and go on modifying the next data register.Write the modified data to the register, then go on modifying the next data register. When the current screen’s last register is modified, exit modifying register status Alarm list key, after setting the alarm list function, press this key will fast switch to the alarm list screen.Clear the chosen area when modifying the register’s dataSet the data to be positive or negative when modifying the register’s data. Number key (0-9)，at the status of data setting ，the number bit to be modified turns to the correspond key value.Common function key.NOTE ：Besides the common function, all the keys in the panel can be defined to have the following functionAny function among “Set ON ”、“Set OFF ”、“Inverse ”、“Momentary ON ”1-4：HMI function and specification◆Draw graph on the computer via edit tool OP20，input characters freely and set PLCaddress，download the screen with serial ports◆ The communication protocol and the screen data will be download to the displaytogether，needn’t PLC to compile the program◆ With password protection function◆ With clock inside（optional）◆ Text cartoon，dynamic display texts◆ With alarm list function，display every line of the alarm information real time◆ The key can be defined to be function key, and they can substitute some mechanic keyson the control tank◆ The display’s face is made of IP65，water-proof、oil-proof◆ With backlight STN LCD display，can display 24 ASC×4 lines1-5：PLC function and input、output specification1-5-1：Input specification and layout1-6：Program cable’s connection chart1-7：Size and installationFor the actual size, please see the following graph：。

貝斯拉 PTB330 數位氣壓器说明书

PTB330 Digital Barometer for Professional Meteorology, Aviation, and Industrial Users Vaisala BAROCAP ® Digital Barometer PTB330 is a new generation barometer, designed for a wide range of high-end atmospheric pressure measurement. The pressuremeasurement of the PTB330 is based on the Vaisala in-house, silicon Vaisala BAROCAP ® Digital Barometer PTB330 with a new trend display.capacitive, absolute pressure sensor- the Vaisala BAROCAP ® Sensor. Itprovides high measurement accuracyand excellent long-term stability.Highly AccurateThe PTB330 series is highly accurate.The Class A barometers for themost demanding applications arefine-tuned and calibrated against ahigh-precision pressure calibrator.Class B barometers are adjusted andcalibrated using electronic workingstandard. All the PTB330 barometerscome with a NIST traceable, factorycalibration certificate.Reliability through RedundancyAccording to customers’ choice, thePTB330 can incorporate one, twoor three BAROCAP ® sensors. Whentwo or three sensors are used, the barometer continuously compares the readings of the pressure sensors Features/Benefits ▪Vaisala BAROCAP® sensor ▪Accurate measurement ▪Excellent long-term stability ▪Added reliability through redundancy ▪Graphical trend display with 1-year history data ▪Height and altitude corrected pressure (QFE, QNH)▪For professional meteorology and aviation, laboratories, demanding industrial applications against one another and provides information on whether these are within the set internal difference criteria. This unique feature provides redundancy in pressure measurement. Thus, users also get a stable and reliable pressure reading at all times as well as a pre-indication of when to service or recalibrate the barometer.QNH and QFE The PTB330 can be set to compensate for QNH and QFE pressure used especially in aviation. The QNH represents the pressure reduced to sea level, based on the altitude and temperature of the observation site. The QFE represents the height corrected pressure of small differences in altitude, for example, the air pressure at the airfield elevation.Graphical Display The PTB330 features a multi-lingual, graphical display allowing users to monitor measurement trends. The graph is updated automatically while measuring and it provides a one-year measurement history. In addition to instant pressure, the PTB330 also provides the WMO pressure trend and tendency codes.Applications The PTB330 can be used successfully for aviation, professional meteorology, and for demanding industrial pressure measurement applications such as accurate laser interferometric measurement and exhaust gas analysis in engine testbenches.Ref. B210708EN-E ©Vaisala 2013This material is subject to copyright protection, with allcopyrights retained by Vaisala and its individual partners. Allrights reserved. Any logos and/or product names are trademarksof Vaisala or its individual partners. The reproduction, transfer,distribution or storage of information contained in this brochurein any form without the prior written consent of Vaisala is strictlyprohibited. All specifications — technical included — are subjectto change without notice.Please contact us at /requestinfo Scan the code for more information Technical DataPerformance BARomETRic PRESSuRE RANgE 500 ... 1100 hPa Class A Class B Linearity*±0.05 hPa ±0.10 hPa Hysteresis*±0.03 hPa ±0.03 hPa Repeatability*±0.03 hPa ±0.03 hPa Calibration uncertainty**±0.07 hPa ±0.15 hPa Accuracy at +20 °C (+68 °F) ***±0.10 hPa ±0.20 hPa BARomETRic PRESSuRE RANgE 50 ... 1100 hPa Class B Linearity*±0.20 hPa Hysteresis*±0.08 hPa Repeatability*±0.08 hPa Calibration uncertainty**±0.15 hPa Accuracy at +20 °C ***±0.20 hPa TEmPERATuRE dEPENdENcE****500 ... 1100 hPa ±0.1 hPa 50 ... 1100 hPa ±0.3 hPa ToTAl AccuRAcy -40 ... +60 °c (-40 ... +140 °F)Class A Class B 500 ... 1100 hPa ±0.15 hPa ±0.25 hPa 50 ... 1100 hPa ±0.45 hPa loNg-TERm STABiliTy 500 ... 1100 hPa ±0.1 hPa/year50 ... 1100 hPa ±0.1 hPa/year * Defined as ±2 standard deviation limits of endpoint non-linearity, hysteresis or repeatability error.** Defined as ±2 standard deviation limits of inaccuracy of the working standard including traceability to NIST.*** Defined as the root sum of the squares (RSS) of endpoint non-linearity, hysteresis error, repeatability error and calibration uncertainty at room temperature.**** Defined as ±2 standard deviation limits of temperature dependence over the operating temperature range.Inputs and Outputs Supply voltage 10 ... 35 VDCSupply voltage sensitivity negligibleTypical power consumption at +20 °C (U in 24 VDC, one pressure sensor)RS-23225 mA RS-48540 mA U out 25 mAI out 40 mAdisplay and backlight +20 mASerial I/O RS232C, RS485/422Pressure units hPa, mbar, kPa, Pa inHg, mmH 20, mmHg, torr, psia Class A Class B Resolution 0.01 hPa 0.1 hPa Settling time at power-up (one sensor) 4 s 3 s Response time (one sensor) 2 s 1 s Acceleration sensitivity negligible Pressure connector M5 (10-32) internal thread Pressure fitting barbed fitting for 1/8” I.D. tubing or quickconnector with shutoff valve for 1/8” hoseMaximum pressure limit 5000 hPa pliance EMC standard EN61326-1:1997 + Am1:1998 + Am2:2001: Industrial Environment AccessoriesSerial interface cable 19446ZZ USB-RJ45 serial connection cable 219685Software interface kit 215005Wall mounting kit 214829Outdoor installation kit (weather shield)215109Installation kit for pole or pipeline 215108Power supply module POWER-1Temperature compensated analog output module AOUT-1TIsolated RS-485 module RS485-1DIN Rail Kit 215094Analog Output (optional)Current output 0 ... 20 mA, 4 ... 20 mA Voltage output 0 ... 1 V, 0 ... 5 V, 0 ... 10 V Accuracy at pressure range 500 ... 1100 hPa 50 ... 1100 hPa at +20 °C ±0.30 hPa ±0.40 hPaat -40 ... +60 °C ±0.60 hPa ±0.75 hPaMechanicsHousing material G AlSi10 Mg (DIN 1725)Housing classification IP66IP65 (NEMA4) with local display Weight 1 - 1.5 kg Operating Environment Pressure range 500 ... 1100 hPa, 50 ... 1100 hPa Temperature range operating -40 ... +60 °C (-40 ... +140 °F)with local display 0 ... +60 °C (+32 ... +140 °F)Data Transfer Software MI70 Link Interface Software Requirement:Microsoft ® Windows OS Microsoft ® Excel。

ST-330B 自动分析电缆测试仪使用手册说明书

ST-330B自动分析电缆测试仪尊敬的顾客感谢您购买本公司ST-330B自动分析电缆测试仪。

在您初次使用该仪器前，请您详细地阅读本使用说明书，将可帮助您熟练地使用本仪器。

我们的宗旨是不断地改进和完善公司的产品，因此您所使用的仪器可能与使用说明书有少许的差别。

如果有改动的话，我们会用附页方式告知，敬请谅解！您有不清楚之处，请与公司售后服务部联络，我们定会满足您的要求。

由于输入输出端子、测试柱等均有可能带电压，您在插拔测试线、电源插座时，会产生电火花，小心电击，避免触电危险，注意人身安全！安全要求请阅读下列安全注意事项，以免人身伤害，并防止本产品或与其相连接的任何其它产品受到损坏。

为了避免可能发生的危险，本产品只可在规定的范围内使用。

为了防止火灾或人身伤害，只有合格的技术人员才可执行维修。

使用适当的电源线。

只可使用本产品专用、并且符合本产品规格的电源线。

正确地连接和断开。

当测试导线与带电端子连接时，请勿随意连接或断开测试导线。

产品接地。

本产品除通过电源线接地导线接地外，产品外壳的接地柱必须接地。

为了防止电击，接地导体必须与地面相连。

在与本产品输入或输出终端连接前，应确保本产品已正确接地。

注意所有终端的额定值。

为了防止火灾或电击危险，请注意本产品的所有额定值和标记。

在对本产品进行连接之前，请阅读本产品使用说明书，以便进一步了解有关额定值的信息。

请勿在无仪器盖板时操作。

如盖板或面板已卸下，请勿操作本产品。

使用适当的保险丝。

只可使用符合本产品规定类型和额定值的保险丝。

避免接触裸露电路和带电金属。

产品有电时，请勿触摸裸露的接点和部位。

在有可疑的故障时，请勿操作。

如怀疑本产品有损坏，请本公司维修人员进行检查，切勿继续操作。

请勿在潮湿环境下操作。

请勿在易爆环境中操作。

保持产品表面清洁和干燥。

――安全术语警告：警告字句指出可能造成人身伤亡的状况或做法。

小心：小心字句指出可能造成本产品或其它财产损坏的状况或做法。

目录一、仪器概述 (4)二、技术说明 (5)1、ST-330B型自动分析电缆测试仪的技术特点 (5)2、仪器原理框图 (6)3、测试原理 (7)三、仪器操作介绍 (7)1、开机前准备工作 (7)2、仪器使用方法及电气检查 (8)四、电缆的故障测试 (14)1、应用低压脉冲法检测低阻、短路、断路、电缆全长 (14)2、用“高压闪络法”测量电缆的高阻和泄漏故障(参考后面高压闪烙法测试接线示意图) (15)五、仪器使用注意事项 (19)六、售后服务 (20)一、仪器概述ST-330B自动分析电缆测试仪采用时域分析法能测试各种电压等级的动力电缆、通信同轴电缆、市话电缆、控制电缆、矿用电缆和海底电缆等电缆的低阻、短路、断路、高阻泄漏故障和高阻闪络性故障。

330说明书(标准版)(09-10-25)

MPU330
低压电动机/线路微机型保护测控装置(V4.0 标准版)
技术说明书

北京思瑞科技有限公司
-0-
目录
.................................................................. - 1 1 产品概述产品概述. 1.1 产品特点............................................................... - 1 1.2 产品功能............................................................... - 1 2 技术指标 .................................................................. - 3 技术指标. 2.1 产品执行标准............................................................ - 3 2.2 环境条件............................................................... - 3 2.3 绝缘性能............................................................... - 3 EMC ）性能.................................................... - 4 2.4 电磁兼容（电磁兼容（EMC EMC）性能 2.5 主回路额定参数......................................................... - 4 2.6 控制器额定参数......................................................... - 4 2.7 测量精度................................................................ - 4 ............................................................ - 5 3 电动机保护原理电动机保护原理. 3.1 启动超时保护........................................................... - 5 3.2 过载保护............................................................... - 5 3.3 过流（堵转）保护....................................................... - 8 3.4 断相保护............................................................... - 8 3.5 电流不平衡保护......................................................... - 8 3.6 接地保护............................................................... - 9 3.7 漏电保护............................................................... - 9 3.8 短路保护............................................................... - 9 3.9 欠载保护.............................................................. - 10 3.10 温度保护............................................................. - 10 3.11 过电压保护............................................................ - 11 3.12 低电压保护........................................................... - 11 3.13 欠功率因数保护....................................................... - 11 3.14 相序保护............................................................. - 12 3.15 T E 时间保护........................................................... - 12 3.16 重启动功能............................................................ - 13 3.17 工艺联锁.............................................................. - 13 3.18 事故停机.............................................................. - 14 ............................................................. - 15 4 线路保护原理线路保护原理. 4.1 过负荷保护............................................................ - 15 4.2 接地保护.............................................................. - 15 4.3 漏电保护.............................................................. - 15 4.4 低压闭锁过流一段....................................................... - 16 4.5 低压闭锁过流二段....................................................... - 16 4.6 过流三段............................................................... - 16 4.7 后加速保护............................................................. - 17 4.8 低电压保护............................................................ - 17 ................................................................. - 18 5 产品尺寸产品尺寸.

凌度BL330行车记录仪中文参数与说明书

产品说明●产品结构1）菜单按钮2）向上选择按钮3）OK确认按钮4）向下选择按钮5）模式选择按钮6）HDMI-OUT复位孔7）TF卡插槽8）USB数据接口9）复位按钮10）电源开关11)电源指示灯12）电池充电指示灯13）MIC按键功能说明：●1）菜单按钮间相互切换；●2）向上选择按钮菜单选项中，向上选择功能键；待机或摄像状态下，数码放大功能键；●3）OK确认按钮录像和拍照确认按钮，摄像模式下，短按此键开始录像，再次短按停止录像；拍照模式下短按此键拍摄照片；菜单模式下为确认按钮；●4）向下选择按钮菜单选项中，向下选择功能键；短按，打开或关闭录音功能；在先按数码放大功能键后，此键变为数码缩小功能键；●5）模式选择按钮短按此键在摄像/拍照/回放之间相互切换；录像过程中短按此键会对当前视屏加锁；●6）HDMI-OUT高清输出端口；●7）TF卡插槽存储卡插槽●8）USB数据接口USB数据接口，①用于连接PC传输数据；②用于连接外接电源给电池充电或提供工作电源；●9）复位按钮当机复位按钮●10）；电源开关长按开/关机；短按打开或关闭红外夜视灯；●11）电源指示灯开机后此电源指示灯点亮；●12）电池充电指示灯插USB线后此电源指示灯点亮表示正在充电，电池充饱后此指示灯息灭；●13 ）MIC录音接收器；特别功能说明：●G-sensor 功能当重力加速（1g=9.80米/秒^2）时，机器会自动将事故发生时的视频保存为不可删除文件；G-sensor重力感应可以在菜单中进行调节2G-4G-6G-8G，出厂默认4G；●SOS功能录像过程中按压MODE键，机器会将当前视频保存为不可删除文件；●自动开/关机支持连接车载电源后，汽车启动自动开机录像，熄火自动保存录像并关机；●不漏秒摄像/拍照基本操作说明：●开机与关机长按电源钮开机，蓝色指示灯会在开机时亮起；再次长按电源钮是关机，此时蓝色指示灯熄灭；注意：录像仪在低电量时会提示电池电压低后自动关机●摄像模式短按键，切换到摄像模式，屏幕左上角显示摄像图标；短按键开始摄像，摄像图标会开始闪动，同时录像指示灯开始闪烁，标明录像工作中；●拍照模式短按键，切换到拍照模式，屏幕左上角显示拍照图标；短按键拍照，拍照时屏幕闪烁一次，表示拍照完成。