各种接头术语的缩略语(1)

合集下载

管道专业常用英文缩写

1、管子及管件缩写中文名称英文名称P管子PipeEL弯头ElbowELL长半径弯头Long radius elbowELS短半径弯头Short radius elbowMEL斜接弯头(吓米腰弯头)Mitre elbowREL异径弯头Reducing elbowT三通TeeLT斜三通Lateral teeRT异径三通Reducing teeR异径管接头(大小头)ReducerCR同心异径管接头(同心大小头)Concentric reducerER偏心异径管接头(偏心大小头)Eccentric reducerCPL管箍CouplingFCPL双头管箍Full couplingHCPL单头管箍Half couplingRCPL异径管箍Reducing couplingBU内外螺纹接头BushingUN活接头UnionHC软管接头Hose couplerSE翻边短节Stub endNIP短节Pipe nipple or straight nipple SNIP异径短节Swaged nippleCP管帽(封头)CapPL管堵(丝堵)PlugBLK盲板BlankSB8字盲板Spectacle blind (blank)RP补强板Reinforcing pad2、法兰缩写中文名称英文名称PLG法兰FlangeWNF对焊法兰Welding neck flangeSOF平焊法兰Slip-on flangeSWF承插焊法兰Socket-welding flangeT螺纹法兰Threaded flangeLJ松套法兰Lapped joint flangeREDF异径法兰Reducing flangeBF法兰盖(盲法兰)Blind flangeFSF法兰密封面Flange dealing faceFF全平面Flat faceRF凸平面Raised faceMFF凹平面Male and female faceLF凹面Female faceLM凸面Male faceRJ环连接面Ring joint faceTG榫槽面Tongue and groove face TF榫面Tongue faceGF槽面Groove face3、垫片缩写中文名称英文名称G垫片GasketNMG非金属垫片Non-metallic gasketAG石棉垫片Asbestos gasketRG橡胶垫片Rubber gasketTEG聚四氟乙烯包复垫片PTFE envelope gasket SMG半金属垫片Semimetallic gasketMJG金属包垫片Meta-jacket gasketSWG缠绕式垫片Spiral wound gasketMG金属垫片Metallic gasketFMG金属平垫片Flat metallic gasket SMSG齿形金属垫片Solid metal serrated gasket LER透镜式金属环垫Lens ring gasketOCR八角形金属环垫Octagonal ring gasket OVR椭圆形金属环垫Oval ring gasketIR/OR内外定位环Inner ring and outer ring IR内定位环Inner ringOR外定位环Outer ring4、紧固件缩写中文名称英文名称B螺栓BoltSB螺柱Stud boltNU螺母NutTB花篮螺母TurnbuckleWSR垫圈WasherSWSR弹簧垫圈Spring washer5、阀门缩写中文名称英文名称GV闸阀Gate valveGLV截止阀Globe valveCHV止回阀Check valveBUV蝶阀Butterfly valveBAV球阀Ball valvePV旋塞阀Plug valve(cock)CV调节阀Control valveSV安全阀Safety valveRV减压阀Pressur reducing valveST蒸汽疏水阀Steam trapperPRV泄压阀Pressur relief valveBV呼吸阀Breather valveNV针形阀Needle valveAV角阀DV隔膜阀TWV三通阀SGV插板阀6、管道上用的小型设备缩写中文名称英文名称SPR气液分离器SeparatorFA阻火器Flame arresterSR过滤器StrainerSRY Y型过滤器Y-type strainerSRT T型过滤器T-type strainerSRB桶式过滤器Bucket type strainerTSR临时过滤器TemporarySIL消声器SilencerSG视镜Sight glassSC取样冷却器Sample coolerDF排液漏斗Drain funnelLM管道混合器Line mixerRO限流孔板Restriction orificeMO混合孔板Mixing orificeRD爆破片（爆破膜）Rupture diskEJ补偿器（膨胀节）Expansion joint7、隔热、伴热缩写中文名称英文名称INS隔热Thermal insulationH保温Hot insulationC保冷Cold insulationP防烫伤隔热Personnel protection insulation T&I伴热Tracing and insulationT管道伴热（冷）TracingEST蒸汽外伴热External steam tracingIST蒸汽内伴热Internal steam tracingSJT蒸汽夹套伴热Steam-jacket tracingET电伴热Electric tracing8、配管材料和等级缩写中文名称英文名称M金属材料Metallic materialCS碳钢Carbon steelCAS铸钢Cast steelFS锻钢Forged steelAS合金钢Alloy steelSS不锈钢Stainless steelAUST·SS奥氏体不锈钢Austenitic stainless-steelCI铸铁Cast ironMI可锻铸铁Malleable ironDI球墨铸铁Ductile ironAL铝AluminumBRS黄铜BrassBRZ青铜BronzeCU紫铜CopperLAS低合金钢Low alloy steelFLAS低合金锻钢For low alloy steelCLAS低合金铸钢Cast low alloy steelTHK壁厚ThicknessSCH表号Schedule numberSTD标准StandardXS加强Extra strongXXS特强Double extra strong9、装置布置缩写中文名称英文名称CN建北Construction northE东EastW西WestS南SouthN北NorthH水平HorizontalV竖直、铅直、直立VerticalGRD地坪GroundUG地下UndergroundBL装置边界线Battery limit lineESEW事故淋浴洗眼器Emergency shower and eye washer HS软管站Hose stationML持续分界线Match linePS管道支架（管架）Piping support PR管桥Pipe rack STRU构架（构筑物）Structure BLDG建筑物BuildingPD清扫设施Purge device PT池PitSHLT棚Shelter COFF围堰CofferdamFL楼板FloorPF平台Plateform10、尺寸标注缩写中文名称英文名称EL标高EBOP管底BCOP管中心CTOP管顶TFOB底平FFOT顶平FCL(屯）中心线CTL切线TSYM对称的SBOS支架底BTOS支架顶TCL净距（净空）CCTC中心至中心CCTF中心至面CCTE中心至端部CETE端到端EFEF法兰端面FFTF面到面FD直径DDN公称直径DID内径IOD外径ODIM尺寸DMAX最大MMIN最小MAVG平均AAPP约、近似APT、EL点标高P11、图表缩写中文名称英文名称工艺流程图管道和仪表流程图接续图详图管段图SPDWG（ISOD-WG）DWG-NO。

管道专业英文缩略语对照(整理版)

管道专业英文缩略语对照P 管子Pipe EL 弯头Elbow ELL 长半径弯头Long radius elbow ELS 短半径弯头Short radius elbow MEL 斜接弯头（虾米腰弯头）Mitre elbow REL 异径弯头Reducing elbow T 三通Tee LT 斜三通Lateral tee RT 异径三通Reducing tee R 异径管接头（大小头）Reducer CR 同心异径管接头（同心大小头）Concentric reducer ER 偏心异径管接头（偏心大小头）Eccentric reducer CPL 管箍Coupling FCPL 双头管箍Full coupling HCPL 单头管箍Half coupling RCPL 异径管箍Reducing coupling BU 内外螺纹接头Bushing UN 活接头Union HC 软管接头Hose coupler SE 翻边短节Stub end NIP 短节Pipe nipple or straight nipple SNIP 异径短节Swaged nipple CP 管帽（封头）Cap PL 管堵（丝堵）Plug BLK 盲板Blank SB 8 字盲板Spectacle blind （blank）RP 补强板Reinforcing pad 法兰缩写中文名称英文名称PLG 法兰Flange WNF 对焊法兰Welding neck flange SOF 平焊法兰Slip-on flange SWF 承插焊法兰Socket-welding flange T 螺纹法兰Threaded flange LJ 松套法兰Lapped joint flange REDF 异径法兰Reducing flange BF 法兰盖（日法兰）Blind flange FSF 法兰密封面Flange scaling face FF 全平面Flat face RF 凸台面Raised face MFF 凹凸面Male ａnd female face LF 凹面Female face LM 凸面Male face RJ 环连接面Ring joint faceTG 榫槽面Tongue ａnd groove face TF 榫面Tongue face GF 槽面Groove face 垫片缩写中文名称英文名称G 垫片Gasket NMG 非金属垫片Non-metallic gasket AG 石棉垫片Asbestos gasket RG 橡胶垫片Rubber gasket TEG 聚四氟乙烯包复垫片PTFE envelope gasket SMG 半金属垫片Semimetallic gasket MJG 金属包垫片Meta-jacket gasket SWG 缠绕式垫片Spiral wound gasket MG 金属垫片Metallic gasket FMG 金属平垫片Flat metallic gasket SMSG 齿形金属垫片Solid metal serrated gasket LER 透镜式金属环垫Lens ring gasket OCR 八角形金属环垫Octagonal ring gasket OVR 椭圆形金属环垫Oval ring gakset IR/OR 内外定位环Inner ring ａnd outer ring IR 内定位环Inner ring OR 外定位环Outer ring 坚固件缩写中文名称英文名称B 螺栓Bolt SB 螺柱Stud bolt NU 螺母Nut TB 花蓝螺母Turnbuckle WSR 垫圈Washer SWSR 弹簧垫圈Spring washer 阀门缩写中文名称英文名称GV 闸阀Gate valve GLV 截止阀Globe valve CHV 止回阀Check valve BUV 蝶阀Butterfly valve BAV 球阀Ball valve PV 旋塞阀Plug valve （cock）CV 调节阀Control valve SV 安全阀Safety valve RV 减压阀Pressure reducing valve ST 蒸汽疏水阀Steam trap PRV 泄压阀Pressur relief valve BV 呼吸阀Breather valve NV 针形阀Needle valve AV 角阀DV 隔膜阀TWV 三通阀SGV 插板阀管道上用的小型设备缩写中文名称英文名称SPR 气液分离器Separator FA 阻火器Flame arrester SR 过滤器Strainer SRY Y 型过滤器Y-type strainer SRT T 型过滤器T-type strainer SRB 桶式过滤器Bucket type strainer TSR 临时过滤器Temporary strainer SIL 消声器Silencer SG 视镜Slight glass SC 取样冷却器Sample cooler DF 排液漏斗Drain funnel LM 管道混合器Line mixer RO 限流孔板Restriction orifice MO 混合孔板Mixing orifice RD 爆破片（爆破膜）Rupture disk EJ 补偿器Expansion joint 隔热、伴热中文名称英文名称INS 隔热Thermal insulation H 保温Hot insulation C 保冷Cold insulation P 防烫伤隔热Personnel protection insulation T&I 伴热Tracing ａnd insulation 管道伴热（冷）Tracing EST 蒸汽外伴热External steam tracing IST 蒸汽内伴热Internal steam tracing SJT 蒸汽夹套伴热Steam-jacket tracing ET 电伴热Electric tracing 配管材料和等级缩写中文名称英文名称M 金属材料Metallic material CS 碳钢Carbon steel CAS 铸钢Cast steel FS 锻钢Forged steel AS 合金钢Alloy steel SS 不锈钢Stainless steel AUST SS 奥氏体不锈钢Austenitic stainless-steel CI 铸铁Cast iron MI 可锻铸铁Malleable iron DI 球墨铸铁Ductile iron AL 铝Aluminum BRS 黄铜Brass BRZ 青铜Bronze CU 紫铜Copper LAS 低合金钢Low alloy steel FLAS 低合金锻钢Forged low alloy steel CLAS 低合金铸钢Cast low alloy steel THK 壁厚Thickness SCH 表号Schedule number STD 标准Standard XS 加强Extra strong XXS 特强Double extra strong 装置布置缩写中文名称英文名称CN 建北Construction north E 东East W 西West S 南South N 北North H 水平Horizontal V 竖直、铅直、直立Vertical GRD 地坪Ground UG 地下Underground BL 装置边界线Battery limit line ESEW 事故沐浴洗眼器Emergency shower ａnd eye washer HS 软管站Hose station ML 接续分界线Match line PS 管道支架（管架）Piping support PR 管桥Pipe rack STRU 构架（构筑物）Structure BLDG 建筑物Building PD 清扫设施Purge device PT 池Pit SHLT 棚Shelter COFF 围堰Cofferdam FL 楼板Floor PF 平台Plateform 尺寸标注缩写中文名称英文名称EL 标高Elevation BOP 管底Bottom of pipe COP 管中心Center of pipe TOP 管顶Top of pipe FOB 底平Flat on bottom FOT 顶平Flat on top CL（屯）中心线Center line TL 切线Tangent line SYM 对称的Symmetrical BOS 支架底Bottom of support TOS 支架顶Top of support CL 净距（净空）Clearance CTC 中心至中心Center to center CTF 中心至面Center to face CTE 中心至端部Center to end ETE 端到端End to end FEF 法兰端面Flange ａnd face FTF 面到面Face to face D 直径Diameter DN 公称直径Nominal diameter ID 内径Inside diameter OD 外径Outside diameter DIM 尺寸Dimension MAX 最大Maximum MIN 最小Minimum AVG 平均Average APP 约、近似Approximate PT.EL 点标高Point elevation 图表缩写中文名称英文名称PFD 工艺流程图Process flow diagram PID 管道和仪表流程图Piping & instrument diagram COD 接续图Continued on drawing DTL 详图Datail SPDWG （ISODWG）管段图Spool drawing （each line isometric drawing）DWGNO 图号Drawing number DWGI 所在图号Drawing identification LOW 材料表List of material MTO 汇料Material take-off APPX 附录Appendix JOB. No. 工号Job Number BEDD 基础工程设计数据Basic engineering design data DEDD 详细工程设计数据Detail engineering design data REV. No. 修改号Recision number REF DWG 参考图Reference drawing SC 采样接口Sample connection 操作方式及工作参数缩写中文名称英文名称AUT 自动Automatic ML 手动Manual control CHOP 链条操作Chain operated CSC 铅封关Car seal close CSO 铅封开Car seal open LC 锁闭Lock closed LO 锁开Lock open NC 正常关Normally close NO 正常开Normally open ATM 大气压Atmosphere PN 公称压力Nominal pressure A 绝压G 表压（T）温度Temperature （P）压力Pressure 施工缩写中文名称英文名称W 焊接Welding AW 电弧焊Arc welding GSAW 气体保护电弧焊Gas shielded-acr welding EFW 电熔焊Elecric fusion welding ERW 电阻焊Electric Resistance welding GW 气焊Gas welding LW 搭接焊Lap welding BW 对焊Butt welding TW 定位焊Tack welding SW 承插焊Socket welding CW 连续焊Continuous welding SEW 密封焊Seal welding SFG 堆焊Surfacing FW 现场焊接Field welding HT 热处理Heat treatment PH 预热Preheating SR 应力消除Stress relief PWHT 焊后热处理Post weld heat treatment EIT 检查、探伤和实验Examination, inspection & testing VE 外观检查Visual examination UI （UT）超声探伤Ultrasonic inspection （test）RI （RT）射线探伤Radiographic inspection （test）MPI （MT）磁粉探伤Magnetic particle inspection （test）LPI （PT）液体渗透检验Liquid penterant inspection （test）HADT 硬度实验Hardness testing HYDT 水压实验Hydraulic testing PNET 气压实验Pneumatic testing 焊条Covered electrode WW 焊丝Welding wire ASSY 装配、组合Assembly F 现场Field F/F 现场制造Field faricated SF 现场决定Suit in field CSP 冷紧Cold spring BCT 螺栓冷紧Bolt cold tightening BHY 螺栓热紧Bolt hot tightening CO 清洗口Clean out ANNY 退火Annealed PE 平端面Plain end BE 坡口端Belelled end THR 螺纹Thread HB 布氏硬度Brinnel hardness RC 洛氏硬度其他缩写中文名称英文名称FDN 基础Foundation INF 信息（资料）Information REF 参考Reference REV 修改Revision SEQ 序号（顺序）Sequence W/E 设备带来With equipment W/I 仪表带来With instrument CM 色标Colour mark CA 腐蚀裕度Corrosion allowance UTL 公用系统Utility UC 公用工程接头Utility connection QTY 数量Quantity WT 重量Weight MHR 工时Man hour BC 螺栓分布圆Bolt circle HP 高点High point LP 低点Low point SUC 吸入（口）Suction DIS 排出（口）Discharge SO 蒸气吹扫（口）Steam out NPT 美国标准锥管螺纹National standard taper pipe thread NPS 美国标准直管螺纹National standard straight pipe thread DR 排液Drain VT 放气Vent RTG （压力）等级Rating CL 等级Class SMLS 无缝Seamless管道结构专业术语-中英文对照管道结构专业术语（中英文对照）A above-ground conduit (pipeline) 地上管道2.0.4 accessible duct 通行地沟2.0.30 acrylonitrile butadiene stryene pipe (ABS) ABS 工程塑料管3.1.22 active earth pressure 主动土压力4.2.12 adaptor slab 井筒盖板6.3.5 aerial crossing structure 跨越结构4.4.23 air-tight test 气密性试验7.0.30 anchor 固定墩2.0.50 arriving shaft 终端工作坑7.0.16 asbestos-ciment pipe(ACP) 石棉水泥管3.1.15B backfill 回填土7.0.23 bearing pressure distribution diagram 地基反力图形4.4.15 bedding angle 基础(座)中心角4.4.7 bend 弯管6.1.2 bending test 弯曲试验4.3.15 beveled pipe 斜口管3.2.13 Boussinecq pressure bulb 布氏压力图形4.4.16 box (rectangular) conduit 矩形管道3.2.2 breadth of conduit 管道宽度4.1.2 breadth of trench 槽宽4.4.11 buried conduit (pepeline) 埋地管道2.0.3 butt and strap joint 抹带接头5.1.16C cable duct 电缆沟2.0.29 cap 盖堵6.1.8 cast in place collar joint 现浇套环接头5.1.20 cast in place joint 现浇接头(缝) 5.1.30 cast-in-place (situ) conduit 现浇管道3.2.16 cast iron pipe (CIP) 铸铁管3.1.3 caulking 填料、捻缝5.1.23 cement mortar lining 水泥砂浆内衬7.0.31 cement mortat with steel mesh strap joint 抹带接头 5.1.17 centrifugal process 离心法3.3.1 chamber 井室、检查室6.3.2 chemically prestressed concrete pipe 自应力混凝土管3.1.11 circular conduit 园形管道3.2.1 coating 涂层2.0.45 coefficient of vertical earth pressure 竖向土压力系数4.2.9 collar type joint 套管(筒)式接头5.1.5 combined drainage conduit (pipeline) 合流管道2.0.15combined duct 综合管道、共同沟2.0.32 compaction around the pipe with relatively untamped above thetop of pipe 中松侧实法7.0.25 compaction the two sides of pipe 胸腔夯实7.0.24 compansator 补偿器6.2.1 composite crossing 组合跨越4.4.26 composit pope 复合管3.1.26 concrete cradle 混凝土管基(管座) 4.4.10 concrete pipe (CP) 混凝土管3.1.8 conduit 管道2.0.1 conduit section 管道截面4.1.1 continuous casting process 连续浇铸法3.3.2 cooling water popeline 冷却水管道2.0.21 core vibrated casting process 芯模震捣法3.3.7 core winding process 管芯缠丝法3.3.10 corrosion prevetive of pipes 管道防腐2.0.51 corrugated pipe 波纹管3.2.7 corpling of borsing 卡箍式管接头6.2.6 coverslab 井筒盖板6.3.5 crack wodth calculation 裂度宽度验算4.4.6 cracking load under tbree-edge bearing test 裂缝荷载4.3.3 crown 顶点4.1.12 culrert 涵洞2.0.17 D D—load D 荷载法4.4.19 dead’load on conduit (pipeline) 管道恒荷载4.2.2 design pressure 设计压力4.2.22 detachable type joint 活接头5.1.7 dewatering 降水7.0.11 distribution of elastic reaction 弹性反力图形4.4.18 double junction 四通6.1.5 down pipe 雨落管2.0.20 down spout 雨落管2.0.20 duck foot 肘管管托5.2.5 duck 管道2.0.1 ductile cast iron pipe(DIP) 可延性铸铁管3.1.6 dynamic water pressure 动水作用力4.2.25 E earth cover (heightofsoil)overconduit 覆土高度4.4.12 earth pressure at rest 静止土压力4.2.13 earth pressure on embankment conduit 上埋式土压力4.2.7 earth pressure on trench conduit 沟埋式土压力4.2.6 earth pressure under soil arch 土拱压力4.2.8 effective length of pipe 管有效长度4.1.5 elastic installation pipeline method 弹性敷管法7.0.8 elastic reaction of soil 土的弹性抗力4.2.15 elbow 弯头6.1.3 electrical conduits 电工套管 2.0.33 elliptical conduit 椭园形管道 3.2.5 embedded type PCCP(PCCP-E) 埋置式预应力钢筒混凝土管3.1.14 embedded-cylinder pipe (ECP) 埋置式预应力钢筒混凝土管 3.1.14 expansion bellows 波纹补偿器 6.2.7 expansion bend 弯管补偿器6.2.2 expansion joint 伸缩接头5.1.3 expansion joint 伸缩节6.2.3 expansion loop 弯管补偿器6.2.2 exterior prism 管侧土柱4.2.11 F fiberglass reinforced pipe(FRP) 玻璃纤维管3.1.23 filament winding process 纤维缠绕法3.3.11 finely divided solid transmission pipeline 细颗粒固体输送管道2.0.27 rixed support 固定管托、固定支座5.2.4 rixed trestle 固定支架4.4.27 flange 法兰6.1.7 flanged joint 法兰接头5.1.11 flat subgrade 素土平基4.4.8 flattening test 压偏试验、偏平试验4.3.8 flexible joint 柔性接头5.1.2 flexble pipe 柔性管2.0.42 flexible rubber expansion joint 可曲挠橡胶接头6.2.8 flexible trestle 柔性支架4.4.29 flexural stiffness ratio 刚柔比4.3.7 four-point loading test 四点法荷载试验4.3.13 free-flow conduit (pipeline) 自流管道2.0.36 fusion joint 热溶接头5.1.9 G gas transmission pipeline 输气管道2.0.23 gasket ring 密封圈5.1.22 glass fibre reinforced plastics pipe (GRP) 玻璃纤维增强热固性塑料管 3.1.23 gravity-flow conduit (pipeline) 重力流管道2.0.36 gray cast iron pipe (CIP) 灰口铸铁管3.1.4 gully gratings and frames 雨水篦6.3.20 gully trap 雨水井6.3.9 H hanger 吊杆6.2.9 haunches under pipe 管下腋角7.0.21 beaped load 堆积荷载 4.2.19 heat-supply pipeline 供热管道 2.0.24 heating pipeline 采暖管道2.0.25 height of conduit 管道高度4.1.3 horizontal earth pressure 水平土压力4.2.5 horseshoe conduit 马蹄形管道3.2.3 hydrostatic pressure 静水压力4.2.24 hydrostatic proof test 水压检验试验4.3.11 impact factor 动力系数4.2.18 impact test 冲击试验4.3.9 industrial pipeline 工业管道2.0.9 inner sleeve joint 内套环接头5.1.19 inside diameter 内径 4.1.8 inspection chamber 检查井6.3.1 interior prism 管上土柱 4.2.10 intermediate jacking station 中继间7.0.17 invert 底点 4.1.13 J jacking pressrue 顶力7.0.20 joint angular deflection 接头角位移 5.1.24 joint axial deformation 接头轴向位移5.1.26 joint deflection test 接头角位移试验5.1.25 joint packing 接头密封料5.1.21 ioint sealant 接头密封料5.1.21 joint straight draw test 接头拉伸试验5.1.27 L lag factor 滞后系数4.4.20 lateral earth presure 侧向土压力4.2.5 leading pipe 导管7.0.18 leak test 严密性试验7.0.29 lined type PCCP(PCCP-L) 内衬式预应力钢筒混凝土管3.1.13 lined-cylinder pipe (LCP) 内衬式预应力钢筒混凝土管3.1.13 liner 内衬2.0.44 live load on conduit(pipeline) 管道活荷载4.2.3 load on conduit (pipeline) 管道荷载4.2.1 loading distribution diagram 荷载分布图形4.4.14 longitudinal calculation 纵向计算4.4.2 M manhole 检查井6.3.1 manhole cover and flames 检查井盖6.3.6 manhole steps 踏步6.3.7 max.temperature difference between costruction and operation 闭合温差7.0.26 mean diameter 平均直径4.1.10 mechanical joint 机械接头5.1.15 mixed structure conduit 混合结构管道3.1.27 N natural (original) ground surface 原状(始)地面7.0.9 natural soil 原状土7.0.10 new austrian tunnelling method 新奥法7.0.5 nodular cast iron pipe 球墨铸铁管3.1.6 non-pressure conduit (pipeline) 无压管道2.0.34 norminal diameter (DN) 公称直径4.1.7 O offset 乙字管6.1.6 olander’s bulb form distribution 奥兰特分布图形4.4.17 oriented (guiding) trestle 导向支架4.4.31 outlet sleeve joint 套环接头5.1.18 outlet 出水口6.3.11 outside diameter 外径4.1.9 oval conduit 椭园形管道3.2.5 over excavation 超挖7.0.13 overhead prpeline 架空管道2.0.7 ovoid conduit 卵形管道3.2.6 P partial fixed trestle 半固定支架4.4.30 passive earth pressure 被动土压力4.2.14 petroleum transmission pipeline 输油管道2.0.22 pipe accesory 管道附件2.0.48 pipe bridge 管桥2.0.8 pipe casing slip joint 套筒式伸缩器6.2.5 pipe clip 管卡、管箍6.2.11 pipe crossing 管道跨越4.4.24 pipe diameter 管直径4.1.6 pipe duct 管沟2.0.28 pipe fitting 管件2.0.47pipe in pipe 双层管3.2.11 pipe jacking method 顶管法7.0.3 pipe length 管长4.1.4 pipe roofing method 管棚法7.0.6 pipe support 管托、管道支座5.2.1 pipeline 管道2.0.1 pipeline (conduit) structure 管道结构2.0.2 pipeline (aerial (over) crossing 管道跨越 2.0.38 pipeline appurtenance 管道附属构筑物 2.0.49 pipeline for waste water (sewerage) in builking 建筑排水管道2.0.19 pipeline for water supply in building 建筑给水管道2.0.18 pipeline joint 管道接头 2.0.46 pipeline pier 管道支礅 2.0.40 pipeline trestle 管道支架 2.0.39 pipeline under crossing 管道穿越2.0.37 plastic sandwich 发泡塑料管3.2.9 polybutylene pipe (PB) 聚丁烯塑料管3.1.20 polyethylene pipe (PE) 聚乙烯塑料管3.1.18 polypropylene pipe (PP) 聚丙烯塑料管3.1.19 precast fabricated conduit 预制装配管道3.2.17 pressure class 压力等级4.3.10 pressure conduit 压力管道2.0.35 prestressed concrete cylinder pipe (PCCP) 预应力钢筒混凝土管3.1.12 prestressed concrete pipe (PCP) 预应力混凝土管3.1.10 profile (ribbed) wall plastic pipe 异型(肋型)塑料管3.2.8 protective cased pipe 保护套管3.2.10 push-on type joint 插入式接头5.1.4 R rare earth cast iron pipe 稀土铸铁管 3.1.5 reducer 反力墙7.0.19 rebated pipe 企口管 3.2.15 reception pit 接收工作坑7.0.16 red mud plastic anti-weather pipe 红泥聚氯乙烯耐候塑料管 3.1.21 reducer 异径管、渐缩管 6.1.1 reducerslab 缩颈盖板 6.3.4 reinforced concrete pipe (RCP) 钢筋混凝土管3.1.9 reinforced plastic mortar pipe (RPMP) 增强塑料砂浆管3.1.25 reinforced thermosetting resin pipe (RTRP) 增强热固性树脂管3.1.24 rigid joint 刚性接头5.1.1 rigid pipe 刚性管2.0.41 rigid trestle 刚性支架4.4.28 rise lf arch conduit 拱沟矢高4.1.15 road (street) gully 雨水口6.3.8 roller support 滚动管托、滚动支座5.2.3 roller suspension process 悬辊法3.3.4 sand box casting process 砂型浇铸法3.3.3 sealing gasket 密封圈5.1.22 self-anchoring joint 自锚式接头5.1.6 self-prestressed concrete pipe 自应力混凝土管3.1.11 semi-elliptical conduit 半椭园形管道 3.2.4 simi-flsxible pipe 半柔性管 2.0.43 semi-rigid pipe 半刚性管 2.0.43 separate foundation 分离式基础4.4.22 serviceebility pressure 工作压力4.2.21 sewge conduit (pipeline) 污水管道2.0.16 shaft 井筒 6.3.3 shaped by injection 注模成型法 3.3.13 shaped by injection molding 挤出成型法 3.3.12 shapped subgrade 土弧基础4.4.9 shield tunnelling method 盾构法7.0.4 single junction 三通6.1.4 sinking pipeline method 沉管法施工7.0.7 site load 施工荷载4.2.20 site pressure test 现场水压试验7.0.28 sleeve connection 杯口连接5.1.29 sleeve expansion joint 松套伸缩接头6.2.4 sleeve joint 套管(筒)式接头5.1.5 slider support 滑动管托、滑动支座5.2.2 slip-on coupling 活箍5.1.7 socket (bell) and spigot joint 承插式接头5.1.13 socket pipe 承口管 3.2.14 soil improvement 地基处理7.0.14 soil treatment 地基处理7.0.14 solvent cement joint 粘接接头5.1.10 splayed emd pipe 斜口管3.2.13 apreading angle 分布角4.4.13 apring hanger 弹簧吊杆6.2.10 apring line 侧点4.1.14 stability clculation 稳定验算4.4.4 stainles ssteel pipe 不锈钢管3.1.2 starting shaft 起始工作坑7.0.15 steel pipe 钢管3.1.1 stiffness calculation 刚度验算4.4.5 stiffness calss 刚度等级4.3.5 stiffness ring 刚性环4.4.21 stiffness test 刚度试验4.3.6 storm sewer conduit 雨水管道2.0.14 straight butt (plain) end pipe 平口管3.1.12 strength calculation 强度计算4.4.3 structural crossing 结构跨越4.4.25 subaqueous pipeline 水下管道2.0.5 submaine pipeline 海底管道2.0.6 submerged pipeline 水下管道2.0.5 support feet 肘管管托5.2.5 srucharge load 堆积荷载4.2.19 surface laver 涂层2.0.45 surge pressure test 波动压力4.2.23 sustained pressure test 持续压力试验4.3.12 T table vibrated casting process 振动台震捣法3.3.8 tbermal insulation of popes 管道隔热、管道保温2.0.52 thickness of conduit sturcture 管道结构厚度4.1.16 thickness of pope wall 管壁厚4.1.11 threaded joint 螺纹接头5.1.12 three-edge bearing test 三支承法试验4.3.1 three-point loading test 三点法荷载试验4.3.14 thrust blocks 止推墩2.0.50 thrust pit 顶进工作坑7.0.15 thrust wall 止推墙7.0.19 tongue and guoove joint 企口式接头5.1.14 tongue and groove pipe 企口管3.2.15 traffic load 车辆荷载4.2.16 transversal calculation 横向计算4.4.1 trench depth 槽深7.0.12 trench depth 开槽施工、沟槽敷设7.0.1 trenchless installation 不开槽施工7.0.2 tunnelling method installation 隧道法敷设7.0.2 two-edge bearing test 双支承法试验4.3.2 tyre pressure 轮压4.2.17 U ultimate lead under three-edge bearing test 破坏荷载4.3.4 unannealed nodular (ductile) cast iron pipe 铸态球墨铸铁管 3.1.7 unbacdfilled trench 末回填沟槽7.0.22 under-ground conduit (pipeline) 地下管道 2.0.3 undisturbed earth 未扰动土7.0.10 unpassable duct 不通行地沟2.0.31 unplasticised polyvinyl chloride pipe (UPVC 管) 硬聚氯乙烯塑料管3.1.17 V vacuum pressure 真空压力4.2.26 ventilating duct 通风管道2.0.26 vertical compressed casting process 径向挤压法、立式挤压法3.3.5 verticcal earth pressure 坚向土压力、垂直土压力4.2.4 vertical vibrated casting process 立式振捣法3.3.6 vitified clay pope 陶土管3.1.16 W wall pope chase 穿墙套管5.1.28 water distribution pipeline 配水管道2.0.12 water removal 排水7.0.11 water supply conduit (pipeline) 给水管道2.0.10 water tight test 闭(灌)水实验7.0.27 water transmission conduit (pipeline) 输水管道 2.0.11 welding joint 焊接接头 5.1.8 wheel pressure 轮压 4.2.17 wlrking pressure 工作压力4.2.21 works hydrostatic test 水压检验试验4.3.11管道基本术语（中英文对照）2.0.1 管道conduit,pipeline,duct 用以输送液体?气（汽）体,细颗粒固体等介质或用以安装输水?输气（汽）?供热等管道?电缆等设施的任意长度的封闭通道的统称? 2.0.2 管道结构pipeline （conduit）structure 输送各种介质或安装管道?电缆等各种设施用的封闭通道及其附属设施（管道附件及附属构筑物）构成的空心体结构的统称? 2.0.3 埋地管道?地下管道buried conduit （pipeline）under-ground conduit （pipeline）敷设在天然或人工回填地面以下或周围覆盖有一定厚度土体的管道? 2.0.4 地上管道above-ground conduit （pipeline）指直接敷设在地面上或地面支礅上的管道? 2.0.5 水下管道submerged pipeline,subapueous pipeline 指敷设在水面以下水体中或水底土体中的管道? 2.0.6 海底管道submarine pipeline 指敷设在海面以下海水中或海底的管道? 2.0.7 架空管道overhead pipeline 指架设在地面以上的管道,由跨越结构和支承结构（支架?托架等）两部分组成? 2.0.8 管桥pipe bridge 管道以桥梁形式跨越河道?湖泊?海域?铁路?公路?山谷等天然或人工障碍专用的构筑物? 2.0.9 工业管道industrial pipeline 通常指工矿企业装置之间管道系统并受到生产中各种输送介质或益出物侵蚀的管道? 2.0.10 给水管道water supply conduit （pipeline）输送原水或成品水管道的统称? 2.0.11 输水管道water transmission conduit （pipeline）一般指输送原水的有一定长度的管道? 2.0.12 配水管道water distribution pipeline 一般输送成品水的管道? 2.0.13 排水管道sewer conduit （pipeline）输送城镇雨?污水或农田排水的管道的统称? 2.0.14 雨水管道storm sewer conduit （pipeline）一般指输送城镇截流雨水的管道? 2.0.15 合流管道combined drainage conduit （pipeline）一般指输送城镇截流雨水?生活污水?工业废水等合流排放的管道? 2.0.16 污水管道sewage conduit （pipeline）一般指输送经过处理或未经处理的城镇或工矿企业的生活污水或工业废水的管道? 2.0.17 涵洞culvert 为宣泄地面水流而设置的穿越路堤或河堤的排水管道构筑物的统称,一般由洞身管道结构和进出水洞口构筑物组成?有管涵?拱涵?箱涵?盖板涵等涵洞结构类型? 2.0.18 建筑给水管道pipeline for water supply in building 用于工业与民用建筑物内部明设或暗设的给水管道的统称? 2.0.19 建筑排水管道pipeline for waste water （sewerage）in building 用于工业与民用建筑物内部明设或暗设的排放生活污水?工业废水管道的统称? 2.0.20 雨落管down pipe?down spout 指将建筑物屋顶或平台上的雨水引到地下排水管道或其他处理手段的安装在室内?外的竖向排水管道,有圆形和矩形等截面形式?2.0.21 冷却水管道cooling water pipeline 冷却物质与冷却装置之间输送未经冷却和经过冷却的水的管道及其附属设施的统称? 2.0.22 输油管道petroleum transmission pipeline 由生产?储存等供油设施向用户输送原油或成品油的管道及其附属设施的统称? 2.0.23 输气管道gas transmission pipeline 由生产?储存等供气设施向用户输送天然气?煤气等燃气的管道及其附属设施的统称? 2.0.24 供热管道heat-supply pipeline 由热电厂?锅炉房等热原向用户输送供热介质的管道及其附属设施的统称?有地上敷设? 地下敷设?管沟敷设?直埋敷设等敷设方式? 2.0.25 采暖管道heating pipeline 建筑物采暖用的由热源或供热装置到散热设备之间输送供热介质的管道及其附件的统称? 2.0.26 通风管道ventilating duct 输送空气和空气混合物的管道及其附件的统称?有架空敷设和地下敷设等敷设方式? 2.0.27 细颗粒固体输送管道finely divided solid transmission pipeline 以高压气体或液体为载体输送煤粉?粉煤灰?水泥等级颗粒固体管道的统称?以水为载体的亦称《浆体管》? 2.0.28 管沟pipe duct 用以敷设和更换输送水-气（汽）等管道设施的地下管道,也是被敷设管道设施的围护结构? 敷设输送供热介质管道的俗称《暖气沟》,有矩形?圆形?拱形等管道结构形式? 2.0.29 电缆沟cable duct 用以敷设和更换电力或电讯电缆设施的地下管道,也是被敷设电缆设施的围护结构,有矩形?圆形?拱形等管道结构形式? 2.0.30 通行地沟accessible duct 人可以在其中通行和进行检查维修等工作的管沟?电缆沟等地下管道的统称?人可以直立通行的称通行地沟（walkway duct）;人必须弯腰通行的称半通行地沟（crawl duct）? 2.0.31 不通行地沟unpassable duct 截面仅能满足敷设管道或电缆的最小净空尺寸要求,人不能进入的地下管沟? 2.0.32 综合管道?共同沟combined duct 在截面内敷设水?气（汽）管道?电缆等输送两种以上不同用途设施的通行地沟的统称? 2.0.33 电工套管electrical conduits 用于保护并保障建筑物（构筑物）内部和室外埋地?架空电气线路系统中穿入与更换电讯或电力电缆的管道的统称?有平滑套管?波绞套管?绝缘套管?阻燃和非阻燃等各种不同材质及性能的类型? 2.0.34 无压管道non-pressure conduit （pipeline）指输送的液体是在其自重重力作用下运行的管道,且其管内液体的最高运行液面不超过管道截面内顶? 2.0.35 压力管道pressure conduit （pipelinne）指输送的液体?气体等介质是在加压的状态下运行的管道的统称,一般以大气压力表示? 根据不同介质及其相应的工作压力的要求,可分为低压?中压?高压等不同压力等级的管道? 2.0.36 自流管道?重力流管道free-flow conduit （pipeline）gravity-flow conduit （pipeline）指输送的液体是在其自重重力作用下运行的管道,其运行最高水头不超过管道截面内顶者为无压管道;其运行最高水头超过管道截面内顶者为有压管道? 2.0.37 管道穿越pipeline under crossing 管道从河流?铁路?公路?建筑物等天然或人工障碍物底部通过的一种方式? 2.0.38 管道跨越pipeline aerial （over）crossing 管道从河流?山谷?铁路?公路等天然或人工障碍物上方通过的一种方式? 2.0.39 管道支架pipeline trestle 支承架空管道用的排架或框架结构,一般由支承柱?帽梁和横梁等杆件组成? 2.0.40 管道支礅pipeline pier 支承架空管道用的实体承重结构,一般用砖?块石或混凝土等制筑? 2.0.41 刚性管rigid pipe 主要依靠管体材料强度支承外力的圆管,在外荷载作用下其变形很小,管子的失效是由于管壁强度的控制? 2.0.42 柔性管flexibe pipe 在外荷载作用下变形显著的圆管?竖向荷载大部分由管子两侧土体所产生的弹性抗力所平衡,管子的失效通常由变形造成而不是管壁的破坏? 2.0.43 半柔性管?半刚性管semi-flexibe pipe,semi-rigid pipe 在竖向外荷载作用下变形足以使两侧土体产生弹性抗力的圆管,土的弹性抗力支承相应的竖向荷载,其数值决定于管子的环向刚度与土体弹性模量的比值?管子的结构计算属柔性管范畴? 2.0.44 内衬liner 涂抹在管内壁或在制管时与管壁结构同时形成的管内表面层?如钢筋混凝土管内壁涂抹或镶嵌的塑料层;钢管和铸铁管内壁涂抹的水泥砂浆层;玻璃纤维管内壁的热圆性树脂层等? 是管道结构的一部分? 2.0.45 涂层coating,surface layer 涂抹在管外壁或在制管时与管壁结构同时形成的管外表面层?如预应力混凝土管外壁喷涂的水泥砂浆层;钢管?铸铁管外壁涂抹的沥青或沥青树脂卷材层;玻璃纤维管外壁的热因性树脂层等?是管道结构的一部分? 2.0.46 管道接头pipeline joint 管道上相邻两端管口或管子与管件连接形式的统称?按其连接功能要求有刚性连接,柔性连接等;按管子结构形式有插入式?企口式?套筒式等;按管材材质有焊接?熔接?粘接等? 2.0.47 管件pipe fitting 圆形管管端之间各类连接件的统称?如渐缩管?弯头?三通?四通等,一般按标准规格尺寸制作? 2.0.48 管道附件pipe accessory 管件?补偿器?阀及其组合件等管道专用部件的统称? 2.0.49 管道附属构筑物pipeline appurtenance 管道系统上设置的安装各种控制输送介质的设施和检查维护用的构筑物的统称?如各种类型的检查井?阀门井?进出水口等?是管道工程的组成部分? 2.0.50 止推墩?固定墩thrust blocds?anchor 阻止压力管道上由内压或温度作用等产生的轴向力引起的管道在水平向和垂直向移动的设施?一般用混凝土浅筑,俗称管道支墩? 2.0.51 管道防腐corrosion prevetive of pipes 减缓或防止钢管?铸铁管等管道在内外介质的化学?电化学作用下或由于微生物的代谢活动而被侵蚀或变质的措施?有涂料防腐?卷材防腐?电防腐等? 2.0.52 管道隔热,管道保温thermal insulation of pipes 为减少供热管道的散热损失或管外介质温度变化对管内介质的影响,在管外壁设置的构造措施?有填充式?涂抹式?缠绕式?预制式等隔热（保温）结构? 3 管材及管道结构 3.1 管材3.1.1 钢管steel pipe 由铁和炭等元素炼制的圆管的统称?按制作工艺有焊接钢管（welded steel pipe）和无缝钢管（seamle ssteel pipe）二类?焊接钢管均由钢板卷焊制作,按焊缝形式有螺旋焊接钢管（spiral welded steel pipe）和直缝焊接钢秋（longitudinal weldedsteel pepe）两种;直缝焊接钢管按焊接工艺不同有直缝埋弧焊管和直缝高频电阻焊管（electric resistence welding,ERW）3.1.2 不锈钢管stainless steel pipe 用少量铬和镍等金属元素炼制的合金钢制作的圆管?具有高度抗腐蚀能力,并耐高温和高压,属合金钢管（alloys steel pipe）范畴? 3.1.3 铸铁管cast iron pipe（CIP）用铁水浇铸的圆管的统称?按管子成型工艺可分为离心铸铁管和连续铸铁管? 3.1.4 灰口铸铁管grey cast iron pipe （CIP）用普通铁水浇铸的圆管,亦称普通铸铁管?用于压力流体输送的称承压铸铁管,用于无压输送液体的称排水铸铁管? 3.1.5 稀土铸铁管rare earth cast iron pipe 指在普通铁水中掺入少量稀土元素浇铸的圆管?具有比灰口铸铁管较高的强度? 3.1.6 球墨铸铁管?可延性铸铁管nodular castiron pipe,ductile cast iron pipe（DIP）指由经过球化和孕育处理的优质铁水（其中石墨组织已由片状变成球状）采用离心浇铸制作的圆管?具有较高强度?较好的韧性（延伸率大于10％）和防腐性能? 3.1.7 铸态球墨铸铁管unannealed nodular （ductile）cast iron pipe 未经退火的球墨铸铁管?其力学性能指标除韧性低外,其他均与球墨铸铁管同? 3.1.8 混凝土管concrete pipe（CP）用混凝土制作的圆管?按成型工艺可分为离心管?悬辊管?立式挤压管和立式振捣管等? 3.1.9 钢筋混凝土管reinforced concrete pipe （RCP）reinforcedconcretepipe（RCP）用配有环筋和纵筋的混凝土制作的圆管?按成型工艺可分为离心管?悬辊管?立式挤压和立式振捣管等? 3.1.10 预应力混凝土管prestressedconcretepipe（PCP）在制管过程中用张拉高强钢丝的工艺使管体混凝土在环向和纵向均处于受压状态的圆管?按制管及环向张拉高强钢丝的不同工艺,分为管芯绕丝管,（指在混凝土管芯上缠绕环向预应力钢丝,使该管芯在环向处于受压状态下喷涂水泥砂浆保护面层制成的圆管,俗称三阶段管）和水力挤压管（俗称一阶段管）两类? 3.1.11 自应力混凝土管self-prestressedconcretepipe, chemicallyprestressedconcretepipe 指在制管过程中利用膨胀水泥的化学作用使混凝土在固化阶段产生的膨胀作用,藉以张拉环向和纵向钢丝,使管体环向和纵向处于受压状态的圆管? 3.1.12 预应力钢筒混凝土管prestressedconcretecylinderpipe（PCCP）指在带钢筒的混凝土管芯上缠绕环向预应力钢丝,使该复合管芯在环向处于受压状态下并喷涂水泥砂浆保护面层而制成的圆管的统称? 3.1.13 内衬式预应力钢筒混凝土管linedtypePCCP （PCCR-L）, lined-cylinderpipe（LCP）指采用离心工艺在钢筒内成型混凝土层后,在钢筒外缠绕环向预应力钢丝,制作水泥砂浆保护层制成的管子? 3.1.14 埋置式预应钢管混凝土管embeddedtypePCCP（PCCP-E）embedded-cylinderpipe（ECP）指采用立式振动成型工艺将钢筒埋入管芯混凝土中,在外侧缠绕环向预应力钢丝,制作水泥砂浆保护层而制成的管子? 3.1.15 石棉水泥管asbestos-cementpipe（ACP）用石棉纤维和水泥抄取成型的圆管?3.1.16 陶土管vitrifiedclaypipe 用粘土制作成型后在窑中烧成的圆管?管表面不上釉的俗称缸瓦管;管表面上釉的称陶瓷管? 3.1.17 硬聚氯乙烯塑料管unplasticisedpolyvinylchloridepipe（UPVC 管）以氯乙烯树脂单体为主,用挤出成型法制成的热塑性塑料圆管?具有一定的耐腐蚀性能,无味, 一般用于输送介质为常温的有压和无压管道?根据使用要求不同,有室内给水?排水用管?埋地给水?排水用管,农排灌溉用管,化工用管等不同品种和规格? 3.1.18 聚乙烯塑。

管件词汇带缩写大全

SWG
金属垫片
Metallic gasket
MG
金属平垫片
Flat metallic gasket
FMG
齿形金属垫片
Solid metal serrated gasket
SMSG
透镜式金属环垫
Lens ring gasket
LER
八角形金属环垫
Octagonal ring gasket
OCR
椭圆形金属环垫
LEP
两端平
Both ends plain
BEP
小端带螺纹的
Small end thread
SET
大端带螺纹的
Large end thread
LET
两端带螺纹的
Both ends thread
BET
一端带螺纹
One end thread
OET
穿线管
EMT Conduit
美国标准椎管螺纹
American standard taper pipe thread
PO
聚四氟乙烯
Polytetrafluoroethene
PTFE
乙丙橡胶
Ethylene propylene rubber
EPR
公称直径
Nominal diameter
DN
公称压力
Nominal pressure
PN
压力级、等级、类别
Class
CL
低压
Low pressure
L.P.
中压
Medium pressure
Sample cooler
SC
排液漏斗
Drain funnel
DF
管道混合器

管道管件等等英文缩写教学内容

编号缩写中文名称英文名称1．管子及管件1.1 P 管子Pipe1.2 EL 弯头Elbow1.2.1 ELL 长半径弯头Long radius elbow1.2.2 ELS 短半径弯头Short radius elbow1.2.3 MEL 斜接弯头（虾米腰弯头）Mitre elbow1.2.4 REL 异径弯头Reducing elbow1.3 T 三通Tee1.3.1 LT 斜三通Lateral tee1.3.2 RT 异径三通Reducing tee1.4 R 异径管接头（大小头）Reducer1.4.1 CR 同心异径管接头（同心大小头）Concentric reducer 1.4.2 ER 偏心异径管接头（偏心大小头）Eccentric reducer 1.5 CPL 管箍Coupling1.5.1 FCPL 双头管箍Full coupling1.5.2 HCPL 单头管箍Half coupling1.5.3 RCPL 异径管箍Reducing coupling1.6 BU 内外螺纹接头Bushing1.7 UN 活接头Union1.8 HC 软管接头Hose coupler1.9 SE 翻边短节Stub end1.10 NIP 短节Pipe nipple or straight nipple1.10.1 SNIP 异径短节Swaged nipple1.11 CP 管帽（封头）Cap1.12 PL 管堵（丝堵）Plug1.13 BLK 盲板Blank1.13.1 SB 8 字盲板Spectacle blind （blank）1.14 RP 补强板Reinforcing pad2．法兰2.1 PLG 法兰Flange2.1.1 WNF 对焊法兰Welding neck flange2.1.2 SOF 平焊法兰Slip-on flange2.1.3 SWF 承插焊法兰Socket-welding flange2.1.4 T 螺纹法兰Threaded flange2.1.5 LJ 松套法兰Lapped joint flange2.1.6 REDF 异径法兰Reducing flange2.1.7 BF 法兰盖（日法兰）Blind flange2.2 FSF 法兰密封面Flange scaling face2.2.1 FF 全平面Flat face2.2.2 RF 凸台面Raised face2.2.3 MFF 凹凸面Male and female face2.2.4 LF 凹面Female face2.2.5 LM 凸面Male face2.2.6 RJ 环连接面Ring joint face2.2.7 TG 榫槽面Tongue and groove face2.2.8 TF 榫面Tongue face2.2.9 GF 槽面Groove face3 . 垫片3.1 G 垫片Gasket3.1.1 NMG 非金属垫片Non-metallic gasket3.1.1.1 AG 石棉垫片Asbestos gasket3.1.1.2 RG 橡胶垫片Rubber gasket3.1.1.3 TEG 聚四氟乙烯包复垫片PTFE envelope gasket 3.1.2 SMG 半金属垫片Semimetallic gasket3.1.2.1 MJG 金属包垫片Meta-jacket gasket3.1.2.2 SWG 缠绕式垫片Spiral wound gasket3.1.3 MG 金属垫片Metallic gasket3.1.3.1 FMG 金属平垫片Flat metallic gasket3.1.3.2 SMSG 齿形金属垫片Solid metal serrated gasket 3.1.3.3 LER 透镜式金属环垫Lens ring gasket3.1.3.4 OCR 八角形金属环垫Octagonal ring gasket3.1.3.5 OVR 椭圆形金属环垫Oval ring gasket3.1.3.6 IR/OR 内外定位环Inner ring and outer ring3.1.3.7 IR 内定位环Inner ring3.1.3.8 OR 外定位环Outer ring4 . 坚固件4.1 B 螺栓Bolt4.1.1 SB 螺柱Stud bolt4.2 NU 螺母Nut4.3 TB 花蓝螺母Turnbuckle4.4 WSR 垫圈Washer4.4.1 SWSR 弹簧垫圈Spring washer5 . 阀门5.1 GV 闸阀Gate valve5.2 GLV 截止阀Globe valve5.3 CHV 止回阀Check valve5.4 BUV 蝶阀Butterfly valve5.5 BAV 球阀Ball valve5.6 PV 旋塞阀Plug valve (cock)5.7 CV 调节阀Control valve5.8 SV 安全阀Safety valve5.9 RV 减压阀Pressure reducing valve5.10 ST 蒸汽疏水阀Steam trap5.11 PRV 泄压阀Pressur relief valve5.12 BV 呼吸阀Breather valve5.13 NV 针形阀Needle valve5.14 AV 角阀5.15 DV 隔膜阀5.16 TWV 三通阀5.17 SGV 插板阀6. 管道上用的小型设备6.1 SPR 气液分离器Separator6.2 FA 阻火器Flame arrester6.3 SR 过滤器Strainer6.3.1 SRY Y 型过滤器Y-type strainer6.3.2 SRT T 型过滤器T-type strainer6.3.3 SRB 桶式过滤器Bucket type strainer6.3.4 TSR 临时过滤器Temporary strainer6.4 SIL 消声器Silencer6.5 SG 视镜Slight glass6.6 SC 取样冷却器Sample cooler6.7 DF 排液漏斗Drain funnel6.8 LM 管道混合器Line mixer6.9 RO 限流孔板Restriction orifice6.9.1 MO 混合孔板Mixing orifice6.1 RD 爆破片(爆破膜) Rupture disk6.11 EJ 补偿器Expansion joint7. 隔热、伴热7.1 INS 隔热Thermal insulation7.1.1 H 保温Hot insulation7.1.2 C 保冷Cold insulation7.1.3 P 防烫伤隔热Personnel protection insulation 7.2 T&I 伴热Tracing and insulation7.3 T 管道伴热（冷）Tracing7.3.1 EST 蒸汽外伴热External steam tracing7.3.2 IST 蒸汽内伴热Internal steam tracing7.3.3 SJT 蒸汽夹套伴热Steam-jacket tracing7.3.4 ET 电伴热Electric tracing8 . 配管材料和等级8.1 M 金属材料Metallic material8.1.1 CS 碳钢Carbon steel8.1.2 CAS 铸钢Cast steel8.1.3 FS 锻钢Forged steel8.1.4 AS 合金钢Alloy steel8.1.5 SS 不锈钢Stainless steel8.1.6 AUST SS 奥氏体不锈钢Austenitic stainless-steel 8.1.7 CI 铸铁Cast iron8.1.8 MI 可锻铸铁Malleable iron8.1.9 DI 球墨铸铁Ductile iron8.1.10 AL 铝Aluminum8.1.11 BRS 黄铜Brass8.1.12 BRZ 青铜Bronze8.1.13 CU 紫铜Copper8.1.14 LAS 低合金钢Low alloy steel8.1.15 FLAS 低合金锻钢Forged low alloy steel8.1.16 CLAS 低合金铸钢Cast low alloy steel8.2 THK 壁厚Thickness8.2.1 SCH 表号Schedule number8.2.2 STD 标准Standard8.2.3 XS 加强Extra strong8.2.4 XXS 特强Double extra strong9. 装置布置9.1 CN 建北Construction north9.2 E 东East9.3 W 西West9.4 S 南South9.5 N 北North9.6 H 水平Horizontal9.7 V 竖直、铅直、直立Vertical9.8 GRD 地坪Ground9.9 UG 地下Underground9.10 BL 装置边界线Battery limit line9.11 ESEW 事故沐浴洗眼器Emergency shower and eye washer 9.12 HS 软管站Hose station9.13 ML 接续分界线Match line9.14 PS 管道支架（管架）Piping support9.15 PR 管桥Pipe rack9.16 STRU 构架（构筑物）Structure9.17 BLDG 建筑物Building9.18 PD 清扫设施Purge device9.19 PT 池Pit9.20 SHLT 棚Shelter9.21 COFF 围堰Cofferdam9.22 FL 楼板Floor9.23 PF 平台Plateform10 . 尺寸标注10.1 EL 标高Elevation10.2 BOP 管底Bottom of pipe10.3 COP 管中心Center of pipe10.4 TOP 管顶Top of pipe10.5 FOB 底平Flat on bottom10.6 FOT 顶平Flat on top10.7 CL（屯）中心线Center line10.8 TL 切线Tangent line10.9 SYM 对称的Symmetrical10.10 BOS 支架底Bottom of support10.11 TOS 支架顶Top of support10.12 CL 净距（净空）Clearance10.13 CTC 中心至中心Center to center10.14 CTF 中心至面Center to face10.15 CTE 中心至端部Center to end10.16 ETE 端到端End to end10.17 FEF 法兰端面Flange and face10.18 FTF 面到面Face to face10.19 D 直径Diameter10.20 DN 公称直径Nominal diameter10.21 ID 内径Inside diameter10.22 OD 外径Outside diameter10.23 DIM 尺寸Dimension10.24 MAX 最大Maximum10.25 MIN 最小Minimum10.26 AVG 平均Average10.27 APP 约、近似Approximate10.28 PT.EL 点标高Point elevation11. 图表11.1 PFD 工艺流程图Process flow diagram11.2 PID 管道和仪表流程图Piping & instrument diagram11.3 COD 接续图Continued on drawing11.4 DTL 详图Datail11.5 SPDWG (ISODWG管段图Spool drawi ng (each line isometric drawi ng)11.6 DWG NO图号Drawing number11.7 DWGI 所在图号Drawing identification11.8 LOW 材料表List of material11.9 MTO 汇料Material take-off11.10 APPX 附录Appendix11.11 JOB. No. 工号Job Number11.12 BEDD 基础工程设计数据Basic engineering design data11.13 DEDD 详细工程设计数据Detail engineering design data11.14 REV. No. 修改号Recision number11.15 REF DWG 参考图Refere nee drawi ng11.16 SC 采样接口Sample connection12 . 操作方式及工作参数12.1 AUT 自动Automatic12.2 ML 手动Manual control12.3 CHOP 链条操作Chain operated12.4 CSC 铅封关Car seal close12.5 CSO 铅封开Car seal open12.6 LC 锁闭Lock closed12.7 LO 锁开Lock open12.8 NC 正常关Normally close12.9 NO 正常开Normally open12.10 ATM 大气压Atmosphere12.11 PN 公称压力Nominal pressure12.12 A 绝压12.13 G 表压12.14 (T) 温度Temperature12.15 (P) 压力Pressure13 . 施工13.1 W 焊接Welding13.1.1 AW 电弧焊Arc welding13.1.2 GSAW 气体保护电弧焊Gas shielded-acr welding13.1.3 EFW 电熔焊Elecric fusion welding13.1.4 ERW 电阻焊Electric Resistance welding13.1.5 GW 气焊Gas welding13.1.6 LW 搭接焊Lap welding13.1.7 BW 对焊Butt welding13.4.8 TW 定位焊Tack welding13.1.9 SW 承插焊Socket welding13.1.10 CW 连续焊Continuous welding13.1.11 SEW 密封焊Seal welding13.1.12 SFG 堆焊Surfacing13.1.13 FW 现场焊接Field welding13.2 HT 热处理Heat treatment13.2.1 PH 预热Preheating13.2.2 SR 应力消除Stress relief13.2.3 PWHT 焊后热处理Post weld heat treatment13.3 EIT 检查、探伤和实验Examination, inspection & testing 13.3.1 VE 外观检查Visual examination13.3.2 UI (UT) 超声探伤Ultrasonic inspection (test)13.3.3 RI (RT) 射线探伤Radiographic inspection (test)13.3.4 MPI (MT) 磁粉探伤Magnetic particle inspection (test) 13.3.5 LPI (PT) 液体渗透检验Liquid penterant inspection (test) 13.3.6 HADT 硬度实验Hardness testing13.3.7 HYDT 水压实验Hydraulic testing13.3.8 PNET 气压实验Pneumatic testing13.3.9 CE 焊条Covered electrode13.3.10 WW 焊丝Welding wire13.3.11 ASSY 装配、组合Assembly13.3.12 F 现场Field13.3.13 F/F 现场制造Field fabricated13.3.14 SF 现场决定Suit in field13.3.15 CSP 冷紧Cold spring13.3.16 BCT 螺栓冷紧Bolt cold tightening13.3.17 BHY 螺栓热紧Bolt hot tightening13.3.18 CO 清洗口Clean out13.3.19 ANNY 退火Annealed13.4 PE 平端面Plain end13.5 BE 坡口端Belelled end13.6 THR 螺纹Thread13.7 HB 布氏硬度Brinnel hardness13.8 RC 洛氏硬度14. 其他14.1 FDN 基础Foundation14.2 INF 信息（资料）Information14.3 REF 参考Reference14.4 REV 修改Revision14.5 SEQ 序号（顺序）Sequence14.6 W/E 设备带来With equipment14.7 W/I 仪表带来With instrument14.8 CM 色标Colour mark14.9 CA 腐蚀裕度Corrosion allowance14.10 UTL 公用系统Utility14.11 UC 公用工程接头Utility connection14.12 QTY 数量Quantity14.13 WT 重量Weight14.14 MHR 工时Man hour14.15 BC 螺栓分布圆Bolt circle14.16 HP 高点High point14.17 LP 低点Low point14.18 SUC 吸入（口）Suction14.19 DIS 排出（口）Discharge14.20 SO 蒸气吹扫（口）Steam out14.21 NPT 美国标准锥管螺纹National standard taper pipe thread 14.22 NPS 美国标准直管螺纹National standard straight pipe thread 14.23 DR 排液Drain14.24 VT 放气Vent14.25 RTG （压力）等级Rating14.26 CL 等级Class14.27 SMLS 无缝Seamless。

化工管件英文缩写讲解

1 管子及管件编号缩写中文名称英文名称1.1 P 管子Pipe1.2 EL 弯头Elbow1.2.1 ELL 长半径弯头Long radius elbow1.2.2 ELS 短半径弯头Short radius elbow1.2.3 MEL 斜接弯头（虾米腰弯头）Mitre elbow1.2.4 REL 异径弯头Reducing elbow1.3 T 三通Tee1.3.1 LT 斜三通Lateral tee1.3.2 RT 异径三通Reducing tee1.4 R 异径管接头（大小头）Reducer1.4.1 CR 同心异径管接头（同心大小头）Concentric reducer 1.4.2 ER 偏心异径管接头（偏心大小头）Eccentric reducer 1.5 CPL 管箍Coupling1.5.1 FCPL 双头管箍Full coupling1.5.2 HCPL 单头管箍Half coupling1.5.3 RCPL 异径管箍Reducing coupling1.6 BU 内外螺纹接头Bushing1.7 UN 活接头Union1.8 HC 软管接头Hose coupler1.9 SE 翻边短节Stub end1.10 NIP 短节Pipe nipple or straight nipple 1.10.1 SNIP 异径短节Swaged nipple1.11 CP 管帽（封头）Cap1.12 PL 管堵（丝堵）Plug1.13 BLK 盲板Blank1.13.1 SB 8字盲板Spectacle blind （blank）1.14 RP 补强板Reinforcing pad2 法兰编号缩写中文名称英文名称2.1 PLG 法兰Flange2.1.1 WNF 对焊法兰Welding neck flange 2.1.2 SOF 平焊法兰Slip-on flange2.1.3 SWF 承插焊法兰Socket-welding flange 2.1.4 T 螺纹法兰Threaded flange2.1.5 LJ 松套法兰Lapped joint flange2.1.6 REDF 异径法兰Reducing flange2.1.7 BF 法兰盖（日法兰）Blind flange2.2 FSF 法兰密封面Flange scaling face2.2.1 FF 全平面Flat face2.2.2 RF 凸台面Raised face2.2.3 MFF 凹凸面Male ａnd female face 2.2.4 LF 凹面Female face2.2.5 LM 凸面Male face2.2.6 RJ 环连接面Ring joint face2.2.7 TG 榫槽面Tongue ａnd groove face2.2.8 TF 榫面Tongue face2.2.9 GF 槽面Groove face3 垫片编号缩写中文名称英文名称3.1 G 垫片Gasket3.1.1 NMG 非金属垫片Non-metallic gasket3.1.1.1 AG 石棉垫片Asbestos gasket3.1.1.2 RG 橡胶垫片Rubber gasket3.1.1.3 TEG 聚四氟乙烯包复垫片PTFE envelope gasket 3.1.2 SMG 半金属垫片Semimetallic gasket3.1.2.1 MJG 金属包垫片Meta-jacket gasket3.1.2.2 SWG 缠绕式垫片Spiral wound gasket3.1.3 MG 金属垫片Metallic gasket3.1.3.1 FMG 金属平垫片Flat metallic gasket3.1.3.2 SMSG 齿形金属垫片Solid metal serrated gasket 3.1.3.3 LER 透镜式金属环垫Lens ring gasket3.1.3.4 OCR 八角形金属环垫Octagonal ring gasket 3.1.3.5 OVR 椭圆形金属环垫Oval ring gakset3.1.3.6 IR/OR 内外定位环Inner ring ａnd outer ring3.1.3.7 IR 内定位环Inner ring3.1.3.8 OR 外定位环Outer ring4 坚固件编号缩写中文名称英文名称4.1 B 螺栓Bolt4.1.1 SB 螺柱Stud bolt4.2 NU 螺母Nut4.3 TB 花蓝螺母Turnbuckle4.4 WSR 垫圈Washer4.4.1 SWSR 弹簧垫圈Spring washer5 阀门编号缩写中文名称英文名称5.1 GV 闸阀Gate valve5.2 GLV 截止阀Globe valve5.3 CHV 止回阀Check valve5.4 BUV 蝶阀Butterfly valve5.5 BAV 球阀Ball valve5.6 PV 旋塞阀Plug valve （cock）5.7 CV 调节阀Control valve5.8 SV 安全阀Safety valve5.9 RV 减压阀Pressure reducing valve 5.10 ST 蒸汽疏水阀Steam trap5.11 PRV 泄压阀Pressur relief valve5.12 BV 呼吸阀Breather valve5.13 NV 针形阀Needle valve5.14 AV 角阀5.15 DV 隔膜阀5.16 TWV 三通阀5.17 SGV 插板阀6 管道上用的小型设备编号缩写中文名称英文名称6.1 SPR 气液分离器Separator6.2 FA 阻火器Flame arrester6.3 SR 过滤器Strainer6.3.1 SRY Y型过滤器Y-type strainer6.3.2 SRT T型过滤器T-type strainer6.3.3 SRB 桶式过滤器Bucket type strainer 6.3.4 TSR 临时过滤器Temporary strainer 6.4 SIL 消声器Silencer6.5 SG 视镜Slight glass6.6 SC 取样冷却器Sample cooler6.7 DF 排液漏斗Drain funnel6.8 LM 管道混合器Line mixer6.9 RO 限流孔板Restriction orifice6.9.1 MO 混合孔板Mixing orifice6.1 RD 爆破片（爆破膜）Rupture disk6.11 EJ 补偿器Expansion joint7 隔热、伴热编号缩写中文名称英文名称7.1 INS 隔热Thermal insulation7.1.1 H 保温Hot insulation7.1.2 C 保冷Cold insulation7.1.3 P 防烫伤隔热Personnel protection insulation 7.2 T&I 伴热Tracing ａnd insulation7.3 T 管道伴热（冷）Tracing7.3.1 EST 蒸汽外伴热External steam tracing7.3.2 IST 蒸汽内伴热Internal steam tracing7.3.3 SJT 蒸汽夹套伴热Steam-jacket tracing7.3.4 ET 电伴热Electric tracing8 配管材料和等级编号缩写中文名称英文名称8.1 M 金属材料Metallic material8.1.1 CS 碳钢Carbon steel8.1.2 CAS 铸钢Cast steel8.1.3 FS 锻钢Forged steel8.1.4 AS 合金钢Alloy steel8.1.5 SS 不锈钢Stainless steel8.1.6 AUSTSS 奥氏体不锈钢Austenitic stainless-steel 8.1.7 CI 铸铁Cast iron8.1.8 MI 可锻铸铁Malleable iron8.1.9 DI 球墨铸铁Ductile iron8.1.10 AL 铝Aluminum8.1.11 BRS 黄铜Brass8.1.12 BRZ 青铜Bronze8.1.13 CU 紫铜Copper8.1.14 LAS 低合金钢Low alloy steel8.1.15 FLAS 低合金锻钢Forged low alloy steel8.1.16 CLAS 低合金铸钢Cast low alloy steel8.2 THK 壁厚Thickness8.2.1 SCH 表号Schedule number8.2.2 STD 标准Standard8.2.3 XS 加强Extra strong8.2.4 XXS 特强Double extra strong9 装置布置编号缩写中文名称英文名称9.1 CN 建北Construction north9.2 E 东East9.3 W 西West9.4 S 南South9.5 N 北North9.6 H 水平Horizontal9.7 V 竖直、铅直、直立Vertical9.8 GRD 地坪Ground9.9 UG 地下Underground9.10 BL 装置边界线Battery limit line9.11 ESEW 事故沐浴洗眼器Emergency shower ａnd eye washer 9.12 HS 软管站Hose station9.13 ML 接续分界线Match line9.14 PS 管道支架（管架）Piping support9.15 PR 管桥Pipe rack9.16 STRU 构架（构筑物）Structure9.17 BLDG 建筑物Building9.18 PD 清扫设施Purge device9.19 PT 池Pit9.20 SHLT 棚Shelter9.21 COFF 围堰Cofferdam9.22 FL 楼板Floor9.23 PF 平台Plateform10 尺寸标注编号缩写中文名称英文名称10.1 EL 标高Elevation10.2 BOP 管底Bottom of pipe10.3 COP 管中心Center of pipe10.4 TOP 管顶Top of pipe10.5 FOB 底平Flat on bottom10.6 FOT 顶平Flat on top10.7 CL（屯）中心线Center line 10.8 TL 切线Tangent line10.9 SYM 对称的Symmetrical10.10 BOS 支架底Bottom of support 10.11 TOS 支架顶Top of support 10.12 CL 净距（净空）Clearance 10.13 CTC 中心至中心Center to center 10.14 CTF 中心至面Center to face 10.15 CTE 中心至端部Center to end 10.16 ETE 端到端End to end10.17 FEF 法兰端面Flange ａnd face 10.18 FTF 面到面Face to face10.19 D 直径Diameter10.20 DN 公称直径Nominal diameter 10.21 ID 内径Inside diameter10.22 OD 外径Outside diameter10.23 DIM 尺寸Dimension10.24 MAX 最大Maximum10.25 MIN 最小Minimum10.26 AVG 平均Average10.27 APP 约、近似Approximate10.28 PT.EL 点标高Point elevation11 图表编号缩写中文名称英文名称11.1 PFD 工艺流程图Process flow diagram11.2 PID 管道和仪表流程图Piping & instrument diagram11.3 COD 接续图Continued on drawing11.4 DTL 详图Datail11.5 SPDWG（ISODWG）管段图Spool drawing （each line isometric drawing）11.6 DWGNO 图号Drawing number11.7 DWGI 所在图号Drawing identification11.8 LOW 材料表List of material11.9 MTO 汇料Material take-off11.10 APPX 附录Appendix11.11 JOB. No. 工号Job Number11.12 BEDD 基础工程设计数据Basic engineering design data11.13 DEDD 详细工程设计数据Detail engineering design data 11.14 REV. No. 修改号Recision number11.15 REFDWG 参考图Reference drawing11.16 SC 采样接口Sample connection12 操作方式及工作参数编号缩写中文名称英文名称12.1 AUT 自动Automatic12.2 ML 手动Manual control12.3 CHOP 链条操作Chain operated12.4 CSC 铅封关Car seal close12.5 CSO 铅封开Car seal open12.6 LC 锁闭Lock closed12.7 LO 锁开Lock open12.8 NC 正常关Normally close12.9 NO 正常开Normally open12.10 ATM 大气压Atmosphere12.11 PN 公称压力Nominal pressure12.12 A 绝压12.13 G 表压12.14 （T）温度Temperature12.15 （P）压力Pressure13 施工编号缩写中文名称英文名称13.1 W 焊接Welding13.1.1 AW 电弧焊Arc welding13.1.2 GSAW 气体保护电弧焊Gas shielded-acr welding 13.1.3 EFW 电熔焊Elecric fusion welding13.1.4 ERW 电阻焊Electric Resistance welding13.1.5 GW 气焊Gas welding13.1.6 LW 搭接焊Lap welding13.1.7 BW 对焊Butt welding13.4.8 TW 定位焊Tack welding13.1.9 SW 承插焊Socket welding13.1.10 CW 连续焊Continuous welding13.1.11 SEW 密封焊Seal welding13.1.12 SFG 堆焊Surfacing13.1.13 FW 现场焊接Field welding13.2 HT 热处理Heat treatment13.2.1 PH 预热Preheating13.2.2 SR 应力消除Stress relief13.2.3 PWHT 焊后热处理Post weld heat treatment13.3 EIT 检查、探伤和实验Examination, inspection & testing 13.3.1 VE 外观检查Visual examination13.3.2 UI （UT）超声探伤Ultrasonic inspection （test）13.3.3 RI （RT）射线探伤Radiographic inspection （test）13.3.4 MPI （MT）磁粉探伤Magnetic particle inspection （test）13.3.5 LPI （PT）液体渗透检验Liquid penterant inspection （test）13.3.6 HADT 硬度实验Hardness testing13.3.7 HYDT 水压实验Hydraulic testing13.3.8 PNET 气压实验Pneumatic testing13.3.9 CE 焊条Covered electrode13.3.10 WW 焊丝Welding wire13.3.11 ASSY 装配、组合Assembly13.3.12 F 现场Field13.3.13 F/F 现场制造Field faricated13.3.14 SF 现场决定Suit in field13.3.15 CSP 冷紧Cold spring13.3.16 BCT 螺栓冷紧Bolt cold tightening13.3.17 BHY 螺栓热紧Bolt hot tightening13.3.18 CO 清洗口Clean out13.3.19 ANNY 退火Annealed13.4 PE 平端面Plain end13.5 BE 坡口端Belelled end13.6 THR 螺纹Thread13.7 HB 布氏硬度Brinnel hardness13.8 RC 洛氏硬度14 其他编号缩写中文名称英文名称14.1 FDN 基础Foundation14.2 INF 信息（资料）Information14.3 REF 参考Reference14.4 REV 修改Revision14.5 SEQ 序号（顺序）Sequence14.6 W/E 设备带来With equipment 14.7 W/I 仪表带来With instrument 14.8 CM 色标Colour mark14.9 CA 腐蚀裕度Corrosion allowance 14.10 UTL 公用系统Utility14.11 UC 公用工程接头Utility connection 14.12 QTY 数量Quantity14.13 WT 重量Weight14.14 MHR 工时Man hour14.15 BC 螺栓分布圆Bolt circle14.16 HP 高点High point14.17 LP 低点Low point14.18 SUC 吸入（口）Suction14.19 DIS 排出（口）Discharge14.20 SO 蒸气吹扫（口）Steam out14.21 NPT 美国标准锥管螺纹National standard taper pipe thread 14.22 NPS 美国标准直管螺纹National standard straight pipe thread 14.23 DR 排液Drain14.24 VT 放气Vent14.25 RTG （压力）等级Rating14.26 CL 等级Class14.27 SMLS 无缝Seamless。

管件常用英语缩写

管子及管件编号缩写中文名称英文名称1.1 P 管子 Pipe 1.2 EL 弯头 Elbow1.2.1 ELL 长半径弯头 Long radius elbow 1.2.2 ELS 短半径弯头 Short radius elbow1.2.3 MEL 斜接弯头（虾米腰弯头） Mitre elbow 1.2.4 REL 异径弯头 Reducing elbow1.3 T 三通 Tee 1.3.1 LT 斜三通 Lateral tee1.3.2 RT 异径三通 Reducing tee 1.4 R 异径管接头（大小头） Reducer1.4.1 CR 同心异径管接头（同心大小头） Concentric reducer 1.4.2 ER 偏心异径管接头（偏心大小头） Eccentric reducer 1.5 CPL 管箍 Coupling 1.5.1 FCPL 双头管箍 Full coupling1.5.2 HCPL 单头管箍 Half coupling 1.5.3 RCPL 异径管箍 Reducing coupling1.6 BU 内外螺纹接头 Bushing 1.7 UN 活接头 Union1.8 HC 软管接头 Hose coupler 1.9 SE 翻边短节 Stub end1.10 NIP 短节 Pipe nipple or straight nipple 1.10.1 SNIP 异径短节 Swaged nipple1.11 CP 管帽（封头） Cap 1.12 PL 管堵（丝堵） Plug1.13 BLK 盲板 Blank 1.13.1 SB 8字盲板 Spectacle blind (blank)1.14 RP 补强板 Reinforcing pad2 法兰编号缩写中文名称英文名称2.1 PLG 法兰 Flange 2.1.1 WNF 对焊法兰 Welding neck flange2.1.2 SOF 平焊法兰 Slip-on flange 2.1.3 SWF 承插焊法兰 Socket-welding flange2.1.4 T 螺纹法兰 Threaded flange 2.1.5 LJ 松套法兰 Lapped joint flange2.1.6 REDF 异径法兰 Reducing flange 2.1.7 BF 法兰盖（日法兰） Blind flange2.2 FSF 法兰密封面 Flange scaling face 2.2.1 FF 全平面 Flat face2.2.2 RF 凸台面 Raised face 2.2.3 MFF 凹凸面 Male and female face2.2.4 LF 凹面 Female face 2.2.5 LM 凸面 Male face2.2.6 RJ 环连接面 Ring joint face 2.2.7 TG 榫槽面 Tongue and groove face2.2.8 TF 榫面 Tongue face 2.2.9 GF 槽面 Groove face3 垫片编号缩写中文名称英文名称3.1 G 垫片 Gasket 3.1.1 NMG 非金属垫片 Non-metallic gasket3.1.1.1 AG 石棉垫片 Asbestos gasket 3.1.1.2 RG 橡胶垫片 Rubber gasket3.1.1.3 TEG 聚四氟乙烯包复垫片 PTFE envelope gasket 3.1.2 SMG 半金属垫片 Semimetallic gasket3.1.2.1 MJG 金属包垫片 Meta-jacket gasket 3.1.2.2 SWG 缠绕式垫片 Spiral wound gasket3.1.3 MG 金属垫片 Metallic gasket 3.1.3.1 FMG 金属平垫片 Flat metallic gasket3.1.3.2 SMSG 齿形金属垫片 Solid metal serrated gasket 3.1.3.3 LER 透镜式金属环垫 Lens ring gasket3.1.3.4 OCR 八角形金属环垫 Octagonal ring gasket 3.1.3.5 OVR 椭圆形金属环垫 Oval ring gakset3.1.3.6 IR/OR 内外定位环 Inner ring and outer ring 3.1.3.7 IR 内定位环 Inner ring3.1.3.8 OR 外定位环 Outer ring4 坚固件编号缩写中文名称英文名称4.1 B 螺栓 Bolt 4.1.1 SB 螺柱 Stud bolt4.2 NU 螺母 Nut 4.3 TB 花蓝螺母 Turnbuckle4.4 WSR 垫圈 Washer 4.4.1 SWSR 弹簧垫圈 Spring washer5 阀门编号缩写中文名称英文名称5.1 GV 闸阀 Gate valve 5.2 GLV 截止阀 Globe valve5.3 CHV 止回阀 Check valve 5.4 BUV 蝶阀 Butterfly valve5.5 BAV 球阀 Ball valve 5.6 PV 旋塞阀 Plug valve (cock)5.7 CV 调节阀 Control valve 5.8 SV 安全阀 Safety valve5.9 RV 减压阀 Pressure reducing valve 5.10 ST 蒸汽疏水阀 Steam trap5.11 PRV 泄压阀 Pressur relief valve 5.12 BV 呼吸阀 Breather valve5.13 NV 针形阀 Needle valve5.14 AV 角阀 5.15 DV 隔膜阀5.16 TWV 三通阀 5.17 SGV 插板阀6 管道上用的小型设备编号缩写中文名称英文名称6.1 SPR 气液分离器 Separator 6.2 FA 阻火器 Flame arrester6.3 SR 过滤器 Strainer 6.3.1 SRY Y型过滤器 Y-type strainer6.3.2 SRT T型过滤器 T-type strainer 6.3.3 SRB 桶式过滤器 Bucket type strainer6.3.4 TSR 临时过滤器 Temporary strainer 6.4 SIL 消声器 Silencer6.5 SG 视镜 Slight glass 6.6 SC 取样冷却器 Sample cooler6.7 DF 排液漏斗 Drain funnel 6.8 LM 管道混合器 Line mixer6.9 RO 限流孔板 Restriction orifice 6.9.1 MO 混合孔板 Mixing orifice6.1 RD 爆破片（爆破膜） Rupture disk 6.11 EJ 补偿器 Expansion joint7 隔热、伴热编号缩写中文名称英文名称7.1 INS 隔热 Thermal insulation 7.1.1 H 保温 Hot insulation7.1.2 C 保冷 Cold insulation 7.1.3 P 防烫伤隔热 Personnel protection insulation 7.2 T&I 伴热 Tracing and insulation 7.3 T 管道伴热（冷） Tracing7.3.1 EST 蒸汽外伴热 External steam tracing 7.3.2 IST 蒸汽内伴热 Internal steam tracing7.3.3 SJT 蒸汽夹套伴热 Steam-jacket tracing 7.3.4 ET 电伴热 Electric tracing8 配管材料和等级编号缩写中文名称英文名称8.1 M 金属材料 Metallic material 8.1.1 CS 碳钢 Carbon steel8.1.2 CAS 铸钢 Cast steel 8.1.3 FS 锻钢 Forged steel8.1.4 AS 合金钢 Alloy steel 8.1.5 SS 不锈钢 Stainless steel8.1.6 AUST SS 奥氏体不锈钢 Austenitic stainless-steel 8.1.7 CI 铸铁 Cast iron 8.1.8 MI 可锻铸铁 Malleable iron8.1.9 DI 球墨铸铁 Ductile iron 8.1.10 AL 铝 Aluminum8.1.11 BRS 黄铜 Brass 8.1.12 BRZ 青铜 Bronze8.1.13 CU 紫铜 Copper 8.1.14 LAS 低合金钢 Low alloy steel8.1.15 FLAS 低合金锻钢 Forged low alloy steel 8.1.16 CLAS 低合金铸钢 Cast low alloy steel8.2 THK 壁厚 Thickness 8.2.1 SCH 表号 Schedule number8.2.2 STD 标准 Standard 8.2.3 XS 加强 Extra strong8.2.4 XXS 特强 Double extra strong9 装置布置编号缩写中文名称英文名称9.1 CN 建北 Construction north 9.2 E 东 East9.3 W 西 West 9.4 S 南 South9.5 N 北 North 9.6 H 水平 Horizontal9.7 V 竖直、铅直、直立 Vertical 9.8 GRD 地坪 Ground9.9 UG 地下 Underground 9.10 BL 装置边界线 Battery limit line9.11 ESEW 事故沐浴洗眼器 Emergency shower and eye washer 9.12 HS 软管站 Hose station9.13 ML 接续分界线 Match line 9.14 PS 管道支架（管架） Piping support9.15 PR 管桥 Pipe rack 9.16 STRU 构架（构筑物） Structure9.17 BLDG 建筑物 Building 9.18 PD 清扫设施 Purge device9.19 PT 池 Pit 9.20 SHLT 棚 Shelter9.21 COFF 围堰 Cofferdam 9.22 FL 楼板 Floor9.23 PF 平台 Plateform10 尺寸标注编号缩写中文名称英文名称10.1 EL 标高 Elevation 10.2 BOP 管底 Bottom of pipe10.3 COP 管中心 Center of pipe 10.4 TOP 管顶 Top of pipe10.5 FOB 底平 Flat on bottom 10.6 FOT 顶平 Flat on top10.7 CL(屯) 中心线 Center line 10.8 TL 切线 Tangent line10.9 SYM 对称的 Symmetrical 10.10 BOS 支架底 Bottom of support10.11 TOS 支架顶 Top of support 10.12 CL 净距（净空） Clearance10.13 CTC 中心至中心 Center to center 10.14 CTF 中心至面 Center to face10.15 CTE 中心至端部 Center to end 10.16 ETE 端到端 End to end10.17 FEF 法兰端面 Flange and face 10.18 FTF 面到面 Face to face10.19 D 直径 Diameter 10.20 DN 公称直径 Nominal diameter10.21 ID 内径 Inside diameter 10.22 OD 外径 Outside diameter10.23 DIM 尺寸 Dimension 10.24 MAX 最大 Maximum10.25 MIN 最小 Minimum 10.26 AVG 平均 Average10.27 APP 约、近似 Approximate 10.28 PT.EL 点标高 Point elevation11 图表编号缩写中文名称英文名称11.1 PFD 工艺流程图 Process flow diagram 11.2 PID 管道和仪表流程图 Piping & instrument diagram11.3 COD 接续图 Continued on drawing 11.4 DTL 详图 Datail11.5 SPDWG(ISODWG) 管段图 Spool drawing (each line isometric drawing)11.6 DWGNO 图号 Drawing number 11.7 DWGI 所在图号 Drawing identification11.8 LOW 材料表 List of material 11.9 MTO 汇料 Material take-off11.10 APPX 附录 Appendix 11.11 JOB. No. 工号 Job Number11.12 BEDD 基础工程设计数据 Basic engineering design data 11.13 DEDD 详细工程设计数据 Detail engineering design data 11.14 REV. No. 修改号 Recision number 11.15 REF DWG 参考图 Reference drawing11.16 SC 采样接口 Sample connection12 操作方式及工作参数编号缩写中文名称英文名称12.1 AUT 自动 Automatic 12.2 ML 手动 Manual control12.3 CHOP 链条操作 Chain operated 12.4 CSC 铅封关 Car seal close12.5 CSO 铅封开 Car seal open 12.6 LC 锁闭 Lock closed12.7 LO 锁开 Lock open 12.8 NC 正常关 Normally close12.9 NO 正常开 Normally open 12.10 ATM 大气压 Atmosphere12.11 PN 公称压力 Nominal pressure 12.12 A 绝压12.13 G 表压 12.14 (T) 温度 Temperature12.15 (P) 压力 Pressure13 施工编号缩写中文名称英文名称13.1 W 焊接 Welding 13.1.1 AW 电弧焊 Arc welding13.1.2 GSAW 气体保护电弧焊 Gas shielded-acr welding 13.1.3 EFW 电熔焊 Elecric fusion welding13.1.4 ERW 电阻焊 Electric Resistance welding 13.1.5 GW 气焊 Gas welding13.1.6 LW 搭接焊 Lap welding 13.1.7 BW 对焊 Butt welding13.4.8 TW 定位焊 Tack welding 13.1.9 SW 承插焊 Socket welding13.1.10 CW 连续焊 Continuous welding 13.1.11 SEW 密封焊 Seal welding13.1.12 SFG 堆焊 Surfacing 13.1.13 FW 现场焊接 Field welding13.2 HT 热处理 Heat treatment 13.2.1 PH 预热 Preheating13.2.2 SR 应力消除 Stress relief 13.2.3 PWHT 焊后热处理 Post weld heat treatment13.3 EIT 检查、探伤和实验 Examination, inspection & testing 13.3.1 VE 外观检查 Visual examination13.3.2 UI (UT) 超声探伤 Ultrasonic inspection (test) 13.3.3 RI (RT) 射线探伤 Radiographic inspection (test)13.3.4 MPI (MT) 磁粉探伤 Magnetic particle inspection (test) 13.3.5 LPI (PT) 液体渗透检验 Liquid penterant inspection (test) 13.3.6 HADT 硬度实验 Hardness testing 13.3.7 HYDT 水压实验 Hydraulic testing13.3.8 PNET 气压实验 Pneumatic testing 13.3.9 CE 焊条 Covered electrode13.3.10 WW 焊丝 Welding wire 13.3.11 ASSY 装配、组合 Assembly13.3.12 F 现场 Field 13.3.13 F/F 现场制造 Field faricated13.3.14 SF 现场决定 Suit in field 13.3.15 CSP 冷紧 Cold spring13.3.16 BCT 螺栓冷紧 Bolt cold tightening 13.3.17 BHY 螺栓热紧 Bolt hot tightening13.3.18 CO 清洗口 Clean out 13.3.19 ANNY 退火 Annealed13.4 PE 平端面 Plain end 13.5 BE 坡口端 Belelled end13.6 THR 螺纹 Thread 13.7 HB 布氏硬度 Brinnel hardness13.8 RC 洛氏硬度 13.9 AT 酸洗14 其他编号缩写中文名称英文名称14.1 FDN 基础 Foundation 14.2 INF 信息（资料） Information14.3 REF 参考 Reference 14.4 REV 修改 Revision14.5 SEQ 序号（顺序） Sequence 14.6 W/E 设备带来 With equipment14.7 W/I 仪表带来 With instrument 14.8 CM 色标 Colour mark14.9 CA 腐蚀裕度 Corrosion allowance 14.10 UTL 公用系统 Utility14.11 UC 公用工程接头 Utility connection 14.12 QTY 数量 Quantity14.13 WT 重量 Weight 14.14 MHR 工时 Man hour14.15 BC 螺栓分布圆 Bolt circle 14.16 HP 高点 High point14.17 LP 低点 Low point 14.18 SUC 吸入（口） Suction14.19 DIS 排出（口） Discharge 14.20 SO 蒸气吹扫（口） Steam out14.21 NPT 美国标准锥管螺纹 National standard taper pipe thread 14.22 NPS 美国标准直管螺纹 National standard straight pipe thread14.23 DR 排液 Drain 14.24 VT 放气 Vent14.25 RTG （压力）等级 Rating 14.26 CL 等级 Class。

管件常用英语缩写

管子及管件编号缩写中文名称英文名称1.1 P 管子 Pipe 1.2 EL 弯头 Elbow1.2.1 ELL 长半径弯头 Long radius elbow 1.2.2 ELS 短半径弯头 Short radius elbow1.2.3 MEL 斜接弯头（虾米腰弯头） Mitre elbow 1.2.4 REL 异径弯头 Reducing elbow1.3 T 三通 Tee 1.3.1 LT 斜三通 Lateral tee1.3.2 RT 异径三通 Reducing tee 1.4 R 异径管接头（大小头） Reducer1.4.1 CR 同心异径管接头（同心大小头） Concentric reducer 1.4.2 ER 偏心异径管接头（偏心大小头） Eccentric reducer 1.5 CPL 管箍 Coupling 1.5.1 FCPL 双头管箍 Full coupling1.5.2 HCPL 单头管箍 Half coupling 1.5.3 RCPL 异径管箍 Reducing coupling1.6 BU 内外螺纹接头 Bushing 1.7 UN 活接头 Union1.8 HC 软管接头 Hose coupler 1.9 SE 翻边短节 Stub end1.10 NIP 短节 Pipe nipple or straight nipple 1.10.1 SNIP 异径短节 Swaged nipple1.11 CP 管帽（封头） Cap 1.12 PL 管堵（丝堵） Plug1.13 BLK 盲板 Blank 1.13.1 SB 8字盲板 Spectacle blind (blank)1.14 RP 补强板 Reinforcing pad2 法兰编号缩写中文名称英文名称2.1 PLG 法兰 Flange 2.1.1 WNF 对焊法兰 Welding neck flange2.1.2 SOF 平焊法兰 Slip-on flange 2.1.3 SWF 承插焊法兰 Socket-welding flange2.1.4 T 螺纹法兰 Threaded flange 2.1.5 LJ 松套法兰 Lapped joint flange2.1.6 REDF 异径法兰 Reducing flange 2.1.7 BF 法兰盖（日法兰） Blind flange2.2 FSF 法兰密封面 Flange scaling face 2.2.1 FF 全平面 Flat face2.2.2 RF 凸台面 Raised face 2.2.3 MFF 凹凸面 Male and female face2.2.4 LF 凹面 Female face 2.2.5 LM 凸面 Male face2.2.6 RJ 环连接面 Ring joint face 2.2.7 TG 榫槽面 Tongue and groove face2.2.8 TF 榫面 Tongue face 2.2.9 GF 槽面 Groove face3 垫片编号缩写中文名称英文名称3.1 G 垫片 Gasket 3.1.1 NMG 非金属垫片 Non-metallic gasket3.1.1.1 AG 石棉垫片 Asbestos gasket 3.1.1.2 RG 橡胶垫片 Rubber gasket3.1.1.3 TEG 聚四氟乙烯包复垫片 PTFE envelope gasket 3.1.2 SMG 半金属垫片 Semimetallic gasket3.1.2.1 MJG 金属包垫片 Meta-jacket gasket 3.1.2.2 SWG 缠绕式垫片 Spiral wound gasket3.1.3 MG 金属垫片 Metallic gasket 3.1.3.1 FMG 金属平垫片 Flat metallic gasket3.1.3.2 SMSG 齿形金属垫片 Solid metal serrated gasket 3.1.3.3 LER 透镜式金属环垫 Lens ring gasket3.1.3.4 OCR 八角形金属环垫 Octagonal ring gasket 3.1.3.5 OVR 椭圆形金属环垫 Oval ring gakset3.1.3.6 IR/OR 内外定位环 Inner ring and outer ring 3.1.3.7 IR 内定位环 Inner ring3.1.3.8 OR 外定位环 Outer ring4 坚固件编号缩写中文名称英文名称4.1 B 螺栓 Bolt 4.1.1 SB 螺柱 Stud bolt4.2 NU 螺母 Nut 4.3 TB 花蓝螺母 Turnbuckle4.4 WSR 垫圈 Washer 4.4.1 SWSR 弹簧垫圈 Spring washer5 阀门编号缩写中文名称英文名称5.1 GV 闸阀 Gate valve 5.2 GLV 截止阀 Globe valve5.3 CHV 止回阀 Check valve 5.4 BUV 蝶阀 Butterfly valve5.5 BAV 球阀 Ball valve 5.6 PV 旋塞阀 Plug valve (cock)5.7 CV 调节阀 Control valve 5.8 SV 安全阀 Safety valve5.9 RV 减压阀 Pressure reducing valve 5.10 ST 蒸汽疏水阀 Steam trap5.11 PRV 泄压阀 Pressur relief valve 5.12 BV 呼吸阀 Breather valve5.13 NV 针形阀 Needle valve5.14 AV 角阀 5.15 DV 隔膜阀5.16 TWV 三通阀 5.17 SGV 插板阀6 管道上用的小型设备编号缩写中文名称英文名称6.1 SPR 气液分离器 Separator 6.2 FA 阻火器 Flame arrester6.3 SR 过滤器 Strainer 6.3.1 SRY Y型过滤器 Y-type strainer6.3.2 SRT T型过滤器 T-type strainer 6.3.3 SRB 桶式过滤器 Bucket type strainer6.3.4 TSR 临时过滤器 Temporary strainer 6.4 SIL 消声器 Silencer6.5 SG 视镜 Slight glass 6.6 SC 取样冷却器 Sample cooler6.7 DF 排液漏斗 Drain funnel 6.8 LM 管道混合器 Line mixer6.9 RO 限流孔板 Restriction orifice 6.9.1 MO 混合孔板 Mixing orifice6.1 RD 爆破片（爆破膜） Rupture disk 6.11 EJ 补偿器 Expansion joint7 隔热、伴热编号缩写中文名称英文名称7.1 INS 隔热 Thermal insulation 7.1.1 H 保温 Hot insulation7.1.2 C 保冷 Cold insulation 7.1.3 P 防烫伤隔热 Personnel protection insulation 7.2 T&I 伴热 Tracing and insulation 7.3 T 管道伴热（冷） Tracing7.3.1 EST 蒸汽外伴热 External steam tracing 7.3.2 IST 蒸汽内伴热 Internal steam tracing7.3.3 SJT 蒸汽夹套伴热 Steam-jacket tracing 7.3.4 ET 电伴热 Electric tracing8 配管材料和等级编号缩写中文名称英文名称8.1 M 金属材料 Metallic material 8.1.1 CS 碳钢 Carbon steel8.1.2 CAS 铸钢 Cast steel 8.1.3 FS 锻钢 Forged steel8.1.4 AS 合金钢 Alloy steel 8.1.5 SS 不锈钢 Stainless steel8.1.6 AUST SS 奥氏体不锈钢 Austenitic stainless-steel 8.1.7 CI 铸铁 Cast iron 8.1.8 MI 可锻铸铁 Malleable iron8.1.9 DI 球墨铸铁 Ductile iron 8.1.10 AL 铝 Aluminum8.1.11 BRS 黄铜 Brass 8.1.12 BRZ 青铜 Bronze8.1.13 CU 紫铜 Copper 8.1.14 LAS 低合金钢 Low alloy steel8.1.15 FLAS 低合金锻钢 Forged low alloy steel 8.1.16 CLAS 低合金铸钢 Cast low alloy steel8.2 THK 壁厚 Thickness 8.2.1 SCH 表号 Schedule number8.2.2 STD 标准 Standard 8.2.3 XS 加强 Extra strong8.2.4 XXS 特强 Double extra strong9 装置布置编号缩写中文名称英文名称9.1 CN 建北 Construction north 9.2 E 东 East9.3 W 西 West 9.4 S 南 South9.5 N 北 North 9.6 H 水平 Horizontal9.7 V 竖直、铅直、直立 Vertical 9.8 GRD 地坪 Ground9.9 UG 地下 Underground 9.10 BL 装置边界线 Battery limit line9.11 ESEW 事故沐浴洗眼器 Emergency shower and eye washer 9.12 HS 软管站 Hose station9.13 ML 接续分界线 Match line 9.14 PS 管道支架（管架） Piping support9.15 PR 管桥 Pipe rack 9.16 STRU 构架（构筑物） Structure9.17 BLDG 建筑物 Building 9.18 PD 清扫设施 Purge device9.19 PT 池 Pit 9.20 SHLT 棚 Shelter9.21 COFF 围堰 Cofferdam 9.22 FL 楼板 Floor9.23 PF 平台 Plateform10 尺寸标注编号缩写中文名称英文名称10.1 EL 标高 Elevation 10.2 BOP 管底 Bottom of pipe10.3 COP 管中心 Center of pipe 10.4 TOP 管顶 Top of pipe10.5 FOB 底平 Flat on bottom 10.6 FOT 顶平 Flat on top10.7 CL(屯) 中心线 Center line 10.8 TL 切线 Tangent line10.9 SYM 对称的 Symmetrical 10.10 BOS 支架底 Bottom of support10.11 TOS 支架顶 Top of support 10.12 CL 净距（净空） Clearance10.13 CTC 中心至中心 Center to center 10.14 CTF 中心至面 Center to face10.15 CTE 中心至端部 Center to end 10.16 ETE 端到端 End to end10.17 FEF 法兰端面 Flange and face 10.18 FTF 面到面 Face to face10.19 D 直径 Diameter 10.20 DN 公称直径 Nominal diameter10.21 ID 内径 Inside diameter 10.22 OD 外径 Outside diameter10.23 DIM 尺寸 Dimension 10.24 MAX 最大 Maximum10.25 MIN 最小 Minimum 10.26 AVG 平均 Average10.27 APP 约、近似 Approximate 10.28 PT.EL 点标高 Point elevation11 图表编号缩写中文名称英文名称11.1 PFD 工艺流程图 Process flow diagram 11.2 PID 管道和仪表流程图 Piping & instrument diagram11.3 COD 接续图 Continued on drawing 11.4 DTL 详图 Datail11.5 SPDWG(ISODWG) 管段图 Spool drawing (each line isometric drawing)11.6 DWGNO 图号 Drawing number 11.7 DWGI 所在图号 Drawing identification11.8 LOW 材料表 List of material 11.9 MTO 汇料 Material take-off11.10 APPX 附录 Appendix 11.11 JOB. No. 工号 Job Number11.12 BEDD 基础工程设计数据 Basic engineering design data 11.13 DEDD 详细工程设计数据 Detail engineering design data 11.14 REV. No. 修改号 Recision number 11.15 REF DWG 参考图 Reference drawing11.16 SC 采样接口 Sample connection12 操作方式及工作参数编号缩写中文名称英文名称12.1 AUT 自动 Automatic 12.2 ML 手动 Manual control12.3 CHOP 链条操作 Chain operated 12.4 CSC 铅封关 Car seal close12.5 CSO 铅封开 Car seal open 12.6 LC 锁闭 Lock closed12.7 LO 锁开 Lock open 12.8 NC 正常关 Normally close12.9 NO 正常开 Normally open 12.10 ATM 大气压 Atmosphere12.11 PN 公称压力 Nominal pressure 12.12 A 绝压12.13 G 表压 12.14 (T) 温度 Temperature12.15 (P) 压力 Pressure13 施工编号缩写中文名称英文名称13.1 W 焊接 Welding 13.1.1 AW 电弧焊 Arc welding13.1.2 GSAW 气体保护电弧焊 Gas shielded-acr welding 13.1.3 EFW 电熔焊 Elecric fusion welding13.1.4 ERW 电阻焊 Electric Resistance welding 13.1.5 GW 气焊 Gas welding13.1.6 LW 搭接焊 Lap welding 13.1.7 BW 对焊 Butt welding13.4.8 TW 定位焊 Tack welding 13.1.9 SW 承插焊 Socket welding13.1.10 CW 连续焊 Continuous welding 13.1.11 SEW 密封焊 Seal welding13.1.12 SFG 堆焊 Surfacing 13.1.13 FW 现场焊接 Field welding13.2 HT 热处理 Heat treatment 13.2.1 PH 预热 Preheating13.2.2 SR 应力消除 Stress relief 13.2.3 PWHT 焊后热处理 Post weld heat treatment13.3 EIT 检查、探伤和实验 Examination, inspection & testing 13.3.1 VE 外观检查 Visual examination13.3.2 UI (UT) 超声探伤 Ultrasonic inspection (test) 13.3.3 RI (RT) 射线探伤 Radiographic inspection (test)13.3.4 MPI (MT) 磁粉探伤 Magnetic particle inspection (test) 13.3.5 LPI (PT) 液体渗透检验 Liquid penterant inspection (test) 13.3.6 HADT 硬度实验 Hardness testing 13.3.7 HYDT 水压实验 Hydraulic testing13.3.8 PNET 气压实验 Pneumatic testing 13.3.9 CE 焊条 Covered electrode13.3.10 WW 焊丝 Welding wire 13.3.11 ASSY 装配、组合 Assembly13.3.12 F 现场 Field 13.3.13 F/F 现场制造 Field faricated13.3.14 SF 现场决定 Suit in field 13.3.15 CSP 冷紧 Cold spring13.3.16 BCT 螺栓冷紧 Bolt cold tightening 13.3.17 BHY 螺栓热紧 Bolt hot tightening13.3.18 CO 清洗口 Clean out 13.3.19 ANNY 退火 Annealed13.4 PE 平端面 Plain end 13.5 BE 坡口端 Belelled end13.6 THR 螺纹 Thread 13.7 HB 布氏硬度 Brinnel hardness13.8 RC 洛氏硬度 13.9 AT 酸洗14 其他编号缩写中文名称英文名称14.1 FDN 基础 Foundation 14.2 INF 信息（资料） Information14.3 REF 参考 Reference 14.4 REV 修改 Revision14.5 SEQ 序号（顺序） Sequence 14.6 W/E 设备带来 With equipment14.7 W/I 仪表带来 With instrument 14.8 CM 色标 Colour mark14.9 CA 腐蚀裕度 Corrosion allowance 14.10 UTL 公用系统 Utility14.11 UC 公用工程接头 Utility connection 14.12 QTY 数量 Quantity14.13 WT 重量 Weight 14.14 MHR 工时 Man hour14.15 BC 螺栓分布圆 Bolt circle 14.16 HP 高点 High point14.17 LP 低点 Low point 14.18 SUC 吸入（口） Suction14.19 DIS 排出（口） Discharge 14.20 SO 蒸气吹扫（口） Steam out14.21 NPT 美国标准锥管螺纹 National standard taper pipe thread 14.22 NPS 美国标准直管螺纹 National standard straight pipe thread 14.23 DR 排液 Drain 14.24 VT 放气 Vent14.25 RTG （压力）等级 Rating 14.26 CL 等级 Class14.27 SMLS 无缝 Seamless 14.28 螺旋缝。

管道工程英文术语缩写

管道工程英文术语缩写(总10页)--本页仅作为文档封面，使用时请直接删除即可----内页可以根据需求调整合适字体及大小--管道工程英文术语缩写（中英对照）1.管子及管件P 管子 PipeEL 弯头ELL 长半径弯头ELS 短半径弯头MEL 斜接弯头（虾米腰弯头）REL 异径弯头T 三通 TeeLT 斜三通RT 异径三通R 异径管接头（大小头） ReducerCR 同心异径管接头（同心大小头） Concentric reducer ER 偏心异径管接头（偏心大小头） Eccentric reducer CPL 管箍 CouplingFCPL 双头管箍 Full couplingHCPL 单头管箍 Half couplingRCPL 异径管箍 Reducing couplingBU 内外螺纹接头 BushingUN 活接头 UnionHC 软管接头 Hose couplerSE 翻边短节 Stub endNIP 短节 Pipe nipple or straight nippleSNIP 异径短节 Swaged nippleCP 管帽（封头） CapPL 管堵（丝堵） PlugBLK 盲板 BlankSB 8字盲板 Spectacle blind (blank)RP 补强板 Reinforcing pad2.法兰 FLG 法兰 FlangeWNF 对焊法兰 Welding neck flangeSOF 平焊法兰 Slip-on flangeSWF 承插焊法兰 Socket-welding flangeT 螺纹法兰 Threaded flangeLJ 松套法兰 Lapped joint flangeREDF 异径法兰 Reducing flangeBF 法兰盖（日法兰） Blind flangeFSF 法兰密封面 Flange scaling FF 全平面 Flat faceRF 凸台面 Raised faceMFF 凹凸面 Male and female faceLF 凹面 Female faceLM 凸面 Male faceRJ 环连接面 Ring joint faceTG 榫槽面 Tongue and groove faceTF 榫面 Tongue faceGF 槽面 Groove face3.垫片 G 垫片 GasketNMG 非金属垫片 Non-metallic gasketAG 石棉垫片 Asbestos gasketRG 橡胶垫片 Rubber gasketTEG 聚四氟乙烯包复垫片 PTFE envelope gasket SMG 半金属垫片 Semimetallic gasketMJG 金属包垫片 Meta-jacket gasketSWG 缠绕式垫片 Spiral wound gasketMG 金属垫片 Metallic gasketFMG 金属平垫片 Flat metallic gasketSMSG 齿形金属垫片 Solid metal serrated gasketLER 透镜式金属环垫 Lens ring gasketOCR 八角形金属环垫 Octagonal ring gasket OVR 椭圆形金属环垫 Oval ring gaksetIR/OR 内外定位环 Inner ring and outer ring IR 内定位环 Inner ringOR 外定位环 Outer ring4.坚固件 B 螺栓 BoltSB 螺柱 Stud boltNU 螺母 NutTB 花蓝螺母 TurnbuckleWSR 垫圈 WasherSWSR 弹簧垫圈 Spring washer5.阀门 GV 闸阀 Gate valveGLV 截止阀 Globe valveCHV 止回阀 Check valveBUV 蝶阀 Butterfly valveBAV 球阀 Ball valvePV 旋塞阀 Plug valve (cock)CV 调节阀 Control valveSV 安全阀 Safety valveRV 减压阀 Pressure reducing valveST 蒸汽疏水阀 Steam trapPRV 泄压阀 Pressur relief valveBV 呼吸阀 Breather valveNV 针形阀 Needle valveAV 角阀DV 隔膜阀TWV 三通阀SGV 插板阀6.管道上用的小型设备 SPR 气液分离器 Separator FA 阻火器 Flame arresterSR 过滤器 StrainerSRY Y型过滤器 Y-type strainerSRT T型过滤器 T-type strainerSRB 桶式过滤器 Bucket type strainerTSR 临时过滤器 Temporary strainerSIL 消声器 SilencerSG 视镜 Slight glassSC 取样冷却器 Sample coolerDF 排液漏斗 Drain funnelLM 管道混合器 Line mixerRO 限流孔板 Restriction orificeMO 混合孔板 Mixing orificeRD 爆破片（爆破膜） Rupture diskEJ 补偿器 Expansion joint7.隔热、伴热 INS 隔热 Thermal insulationH 保温 Hot insulationC 保冷 Cold insulationP 防烫伤隔热 Personnel protection insulationT&I 伴热 Tracing and insulationT 管道伴热（冷） TracingEST 蒸汽外伴热 External steam tracingIST 蒸汽内伴热 Internal steam tracingSJT 蒸汽夹套伴热 Steam-jacket tracingET 电伴热 Electric tracing8.配管材料和等级 M 金属材料 Metallic material CS 碳钢 Carbon steelCAS 铸钢 Cast steelFS 锻钢 Forged steelAS 合金钢 Alloy steelSS 不锈钢 Stainless steelAUSTSS 奥氏体不锈钢 Austenitic stainless-steel CI 铸铁 Cast ironMI 可锻铸铁 Malleable ironDI 球墨铸铁 Ductile ironAL 铝 AluminumBRS 黄铜 BrassBRZ 青铜 BronzeCU 紫铜 CopperLAS 低合金钢 Low alloy steelFLAS 低合金锻钢 Forged low alloy steelCLAS 低合金铸钢 Cast low alloy steelTHK 壁厚 ThicknessSCH 表号 Schedule numberSTD 标准 StandardXS 加强 Extra strongXXS 特强 Double extra strong9.装置布置 CN 建北 Construction northE 东 EastW 西 WestS 南 SouthN 北 NorthH 水平 HorizontalV 竖直、铅直、直立 VerticalGRD 地坪 GroundUG 地下 UndergroundBL 装置边界线 Battery limit lineESEW 事故沐浴洗眼器 Emergency shower and eye washer HS 软管站 Hose stationML 接续分界线 Match linePS 管道支架（管架） Piping supportPR 管桥 Pipe rackSTRU 构架（构筑物） StructureBLDG 建筑物 BuildingPD 清扫设施 Purge devicePT 池 PitSHLT 棚 ShelterCOFF 围堰 CofferdamFL 楼板 FloorPF 平台 Plateform10.尺寸标注 EL 标高 Elevation BOP 管底 Bottom of pipeCOP 管中心Center of pipeTOP 管顶 Top of pipeFOB 底平 Flat on bottomFOT 顶平 Flat on topCL(屯) 中心线 Center lineTL 切线 Tangent lineSYM 对称的 SymmetricalBOS 支架底 Bottom of supportTOS 支架顶 Top of supportCL 净距（净空） ClearanceCTC 中心至中心 Center to centerCTF 中心至面 Center to faceCTE 中心至端部 Center to endETE 端到端 End to endFEF 法兰端面 Flange and faceFTF 面到面 Face to faceD 直径 DiameterDN 公称直径 Nominal diameterID 内径 Inside diameterOD 外径 Outside diameterDIM 尺寸 DimensionMAX 最大 MaximumMIN 最小 MinimumAVG 平均 AverageAPP 约、近似 Approximate点标高 Point elevation11.图表 PFD 工艺流程图 Process flow diagram PID 管道和仪表流程图 Piping & instrument diagram COD 接续图 Continued on drawingDTL 详图 DatailSPDWG(ISODWG) 管段图 Spool drawing (each line isometric drawing) DWGNO 图号 Drawing numberDWGI 所在图号 Drawing identificationLOW 材料表 List of materialMTO 汇料 Material take-offAPPX 附录 AppendixJOB. No. 工号 Job NumberBEDD 基础工程设计数据 Basic engineering design dataDEDD 详细工程设计数据 Detail engineering design dataREV. No. 修改号 Recision numberREFDWG 参考图 Reference drawingSC 采样接口 Sample connection12.操作方式及工作参数 AUT 自动 AutomaticML 手动 Manual controlCHOP 链条操作 Chain operatedCSC 铅封关 Car seal closeCSO 铅封开 Car seal openLC 锁闭 Lock closedLO 锁开 Lock openNC 正常关 Normally closeNO 正常开 Normally openATM 大气压 AtmospherePN 公称压力 Nominal pressureA 绝压G 表压(T) 温度 Temperature(P) 压力 Pressure13.施工 W 焊接 WeldingAW 电弧焊 Arc weldingGSAW 气体保护电弧焊 Gas shielded-acr welding EFW 电熔焊 Elecric fusion weldingERW 电阻焊 Electric Resistance weldingGW 气焊 Gas weldingLW 搭接焊 Lap weldingBW 对焊 Butt weldingTW 定位焊 Tack weldingSW 承插焊 Socket weldingCW 连续焊 Continuous weldingSEW 密封焊 Seal weldingSFG 堆焊 SurfacingFW 现场焊接 Field weldingHT 热处理 Heat treatmentPH 预热 PreheatingSR 应力消除 Stress reliefPWHT 焊后热处理 Post weld heat treatmentEIT 检查、探伤和实验 Examination, inspection & testing VE 外观检查 Visual examinationUI (UT) 超声探伤 Ultrasonic inspection (test)RI (RT) 射线探伤 Radiographic inspection (test)MPI (MT) 磁粉探伤 Magnetic particle inspection (test)LPI (PT) 液体渗透检验 Liquid penterant inspection (test) HADT 硬度实验 Hardness testingHYDT 水压实验 Hydraulic testingPNET 气压实验 Pneumatic testing CE 焊条 Covered electrodeWW 焊丝 Welding wireASSY 装配、组合 AssemblyF 现场 FieldF/F 现场制造 Field faricatedSF 现场决定 Suit in fieldCSP 冷紧 Cold springBCT 螺栓冷紧 Bolt cold tightening BHY 螺栓热紧 Bolt hot tightening CO 清洗口 Clean outANNY 退火 AnnealedPE 平端面 Plain endBE 坡口端 Belelled endTHR 螺纹 ThreadHB 布氏硬度 Brinnel hardnessRC 洛氏硬度14.其他 FDN 基础 FoundationINF 信息（资料） InformationREF 参考 ReferenceREV 修改 RevisionSEQ 序号（顺序） SequenceW/E 设备带来 With equipmentW/I 仪表带来 With instrumentCM 色标 Colour markCA 腐蚀裕度 Corrosion allowanceUTL 公用系统 UtilityUC 公用工程接头 Utility connection QTY 数量 QuantityWT 重量 WeightMHR 工时 Man hourBC 螺栓分布圆 Bolt circleHP 高点 High pointLP 低点Low pointSUC 吸入（口） SuctionDIS 排出（口） DischargeSO 蒸气吹扫（口） Steam outNPT 美国标准锥管螺纹 National standard taper pipe threadNPS 美国标准直管螺纹 National standard straight pipe thread DR 排液 DrainVT 放气 VentRTG （压力）等级 RatingCL 等级 ClassSMLS 无缝 Seamless螺旋缝。

管件英文代号及缩写

1 【2 】.swaged nipple conc smls.：大小头齐心无缝2.BLE/PSE：Beveled Large End/Plain Small End大端开破口/小端平端3.PE/PE.PBE.BLE/PSE.BSE/PLE：平端/平端.两端平端.大端开破口/小端平端.端开破口/大端平端4.ELBOW 90 DEG LR BW SMLS.：弯头 90度长半径（R=1.5DN）对焊无缝SR ：短半径（R=1.0DN）5.PIPE SMLS PE/BE：无缝管平口/坡口6.GASKET FLAT RING：垫圈平面环形pressed asbestos fiber jointing sheet：石棉胶板8.SPECTACLE BLIND：8字盲板9.STUDBOLT ALLOY STEEL：双头螺栓合金钢10.NUMild Steel 软钢; 低碳钢软钢丝Mild Steel Arc Welding Electrode 低碳钢焊条Mild Steel Channel 槽钢Mild Steel Checkered Plate 斑纹钢板Mild Steel Equal Angle 等边角钢Mild Steel Expanded Sheets 钢板网Mild Steel Fire Box 软钢板火箱Mild Steel Hexagonal Bolts 六角螺丝梗Mild Steel Hexagonal Bolts And Nuts 六角螺丝闩Mild Steel I-Beam 低碳工字钢Mild Steel Ingot 低碳钢锭Mild Steel Plate 软钢板Mild Steel Reinforcement (含钢量0.12--0.25%) 软钢钢筋Mild Steel Shank 软钢手柄Mild Steel Sheet 软钢皮TS：螺母（nut的复数）11.BOLT：螺栓12.FULL BORE：与管子等径的.纵贯式（Valve Ball, Full Bore全通径球阀）13.REDUCED/REGULAR BORE：缩径（Valve Ball, Reduced/Regular Bore缩径球阀）14.SW ENDS / CARBON STEEL BODY / DIMS TO BS EN：承插焊/碳钢阀体/尺寸按照英国及欧洲标准15.RF FLANGED ENDS：凸面法兰衔接（表示阀门衔接情势）16.TEE EQUAL：等径三通17.SOCKOLET：承插支管台18.THREBOLET：螺纹支管台19.常见阀门衔接面英文表示：LUGGED ------>凸耳对夹式的,秘诀的一种构造情势.一般用于大直径的止回阀或蝶阀,属于对夹衔接的一个变种,要配对法兰.衔接螺栓要加长RING TYPE JOINT------>环衔接面,这是法兰密封面的类型,一般如许写要法兰的.SOCKET WELD------>承插焊衔接,不需法兰THREADED---->螺纹衔接,不要法兰WAFER------>对夹式衔接,相似于凸耳的,也是一种阀门的构造情势,属于FLANGELESS 阀门,阀门本体没有法兰,但是要有配对法兰衔接.螺栓要加长BUTTERWELD/THREADED------>对焊/罗纹.都不要法兰,一般是用于描写小阀门,两端的衔接情势不同的情形SOCKET WELD /THREADED--->承插焊/螺纹,都不要法兰,一般是用于描写小阀门,两端的衔接情势不同的情形20.VALVE GATE / SOLID WEDGE：闸阀/整体楔形闸板21.MANUFACTURERS STANDARD：行业标准22.union：平日指的是活接头,也就是先生傅常说的“油印”;nipple：一般是指用于软管站衔接软管的接头,衔接方法为多样（焊接／丝接／法兰衔接）;pipe：一般就指短管,个中的couple特指两端带法兰的短管衔接,即俗称的“车轱辘管”.23.NIPPLE：短节PBE：Plain Both End两端平口POE /TOE：plain one end/thread one end一端平口/一端螺纹24.CAP：管帽25.VALVE CHECK PISTON：止回阀活塞式26.THREADED：螺纹27.GALVANISED：镀锌28.NITRILE RUBBER：丁腈橡胶29.HOT DIPPED GALVANISED：热浸锌30.BRONZE：铜31.EFW Pipe：电熔焊管32.ERW即电阻焊Electric resistance welding的第一字母的缩写ERW管与埋弧焊管的焊接方法有明显的不同,采用的是无填充金属的压力焊接方法,焊缝中没有填充其他成分,靠高频电流的集肤效应和邻近效应, 使板边刹时加热到焊接温度,由挤压辊挤压形成锻造组织的焊缝. 高品德的钢管请求采用焊缝线上或离线热处理,使焊区组织细化, 优质ERW焊管的焊缝可以达到与母材雷同的韧性水准,这是埋弧焊接工艺无法达到的.EFW即电熔焊 Electric fusion welding 的第一字母的缩写埋弧焊（SAW）-电熔焊（EFW）的一种,就是经由过程一个或几个自耗电极与工件之间对金属加热使金属之间联合中的一种工艺,电弧使金属和填充材料充分熔化,不须要加压,填充金属部分勤工全体来自于电极.熔化气体破坏焊（GMAW）--电熔焊（EFW）的一种,这种工艺与埋弧焊相似,但它的破坏是来自于惰性气体,后果会更好.螺旋焊---这也是埋弧焊的一种,带有一条螺旋焊缝.33.管子：A312 Gr.TP304A409 Gr.TP304A312 Gr.TP304H管件：A403 Gr.WP304A403 Gr.WP304H锻件：A182 Gr.F304A182 Gr.F304HWP是直缝焊接钢管,TP是冷拔无缝钢管,F是锻件34.STAINLESS：不锈钢35.LINE BLIND AND SPACER：实心和空心连在一路的插板和插环（大尺寸管道用,相当于小尺寸管道用的8字盲板）Blind：插板 spacer：垫环36.Spiral Wound Gasket：金属缠绕垫37.NOM THK：nominalthickness 公称厚度38.VALVE GLOBE,REGULAR PATTERN：截止阀,正常模式39.WELDOLET：焊接支管台40.ESDV：Emergency Shut Down Valve 紧迫关断阀41.Swing check valve：旋启式止回阀42.hex hd：六角头43.Reducer Ecc.：大小头偏幸的44.板式平焊PL 带颈平焊SO 带颈对焊WN承插焊SW螺纹TN整体IF法兰盖BL45 螺纹支管台thread let 焊接支管台weld let 承插支管台sock let 弯头支管台elbolet 斜接支管台latrolet 镶入式支管嘴sweepolet 短管支管台 nipolet46 1 grain 格令=0.065 gram 克1 dram 打兰=1.772 grams 克1 ounce 盎司=16 drams 打兰=28.35 grams 克1 pound 磅=16 ounces 盎司=7000 grains 谷=0.4536 kilogram 千克1 stone 英石=14 pounds 磅=6.35 kilograms 千克1 quarter 四分之一英担=2 stones 英石=12.70 kilograms 千克1 hundredweight 英担=4 quarters 四分之一英担=50.80 kilograms 千克1 short ton 短吨( 美吨)=2000 pounds 磅=0.907 tonne 公吨1 (long) ton 长吨 ( 英吨 )=20 hundredweight 英担 =1.016 tonnes 公吨TAPER JOINT 锥形衔接Coupling直管短接fireproof耐火的NPTF锥管螺纹。

(整理)管件常用英文词汇及缩写I

弯头joint弯头angle fittings; bent pipe; elbow; knee弯头扳手bent-handle wrench; bent spanner弯头车刀angular tool弯头持针钳curved needle holders弯头刀架knee tool弯头道钉brob弯头管swan neck弯头键gib head key弯头接合knee-joint弯头螺栓bolt with one end bent back弯头锁紧螺母elbow jam unt弯头套管elbow union弯头套筒扳手offset socket wrench弯头脱水器elbow separator弯头芯盒elbow core box活接活接loose joint活接地swinging earth活接结合articulated joint活接联接器joint coupling活接三通union tee活接头articulation; union swivel; union活接头螺母union nut活接头螺栓swing bolt活接头套管union thimble活接卸槽articulated chute (浇混凝土用的)三通三通tee bend; tee branch; tee joint; tee conneetion; tee fitting; wye; Y; yoke 三通玻璃栓three-way glass stopcock三通道放大器three-channel amplifier; three-path amplifier三通道自动驾驶仪three-dimensional autopilot三通电缆分线盒three-way coupling box三通阀tee valve; three-port valve; three-way valve; triple valve三通阀盖triple-valve cap三通阀活塞triple-valve piston三通阀联箱three way valve menifold三通阀体triple body; triple-valve body三通管single sweep tee; T-branch (pipe); three-limb tube三通管接头tee pipe coupling三通横长horizontal length of tee三通换向旋塞three-way reversing cock三通活栓three-way cock三通货协定triparties currency agreement三通接头tee coupling; tee fitting; tee union; three-way piece; three-way connection 三通接线夹three-way connector三通开关three-way cock三通控制阀three-way control valve三通连接tee junction三通路循环器three-terminal circulator三通式热风炉three-pass stove三通天线转发开关triplexer三通筒triple cylinder三通筒垫密片triple-cylinder gasket三通弯头three-way elbow三通旋塞tee cock; three-way cock; three-throw tap三通循环器three-terminal circulator三通液体流量计tee fluid flow meter三通闸阀treble ported slide valve直通直通direct connection; straight in; straight bore; through; feed(-)through; once-through 直通拨号through dial(l)ing直通测量线路end-to-end measurement直通单向阀in-line check valve; straight check valve; straightway check valve直通道路through road直通的through and through直通地dead earth; dead ground直通垫外底through midsole直通电报telex直通电报通信telex communication直通电流through current直通电流偏置through current bias直通电路direct circuit直通阀pass valve; straight-through valve; straightway valve; through valve 直通干馏炉through retort直通锅炉once-through boiler直通换料once-through refuelling直通回路straight circuit直通汇接呼叫制straight forwardjunction working直通监控through supervision直通接头straight coupling; straight fitting直通接线装置through joint直通街道through expressway; through street; throughway直通进位standing carry直通开关globe cock直通空气制动阀straight air brake valve直通空气制动器straight air brake直通快动阀straight-through fast acting valve直通连接straight-through joint直通裂化straight-through cracking直通流动straight through flowS型弯管“S” bend单侧偏置90º弯管Single offset “U”bendU型弯管“U” bend双偏置U型膨胀弯管Double offset expansio n “U” bend斜接弯头Mitre elbow斜接弯Mitre bend三节斜接管4-piece mitre bend折皱弯管Corrugated bend法兰法兰端Flanged end坡口端；对焊端Beveled end [BEV.E];Butt welded end平端Plain end [PE]承插焊端Socket welding end螺纹端Threaded end [TE]承口Bell end焊接端Welding end钢管法兰Steel pipe flange螺纹法兰Threaded flange滑套法兰（平焊法兰) Slip-on-welding flange Slip-on [SO] flange 承插焊法兰Socket welding flange松套法兰Lap joint flange [LJF]对焊法兰Weld neck flange [WNF]法兰盖Blind flange ; Blind孔板法兰Orifice flange异径法兰Reducimg flange盘座式法兰Pad type flange松套带颈法兰Loose hubbed flange板式平焊法兰Welding plate flange松套法兰Lap joint flange [LJF]对焊法兰Weld neck flange [WNF]法兰盖Blind flange ; Blind孔板法兰Orifice flange异径法兰Reducimg flange盘座式法兰Pad type flange松套带颈法兰Loose hubbed flange板式平焊法兰Welding plate flange对焊环（与stubend相似）Welding neck collar（与stubend相似）平焊环Welding-on collar管端突缘Stub end翻边端Lapped pipe end松套板式法兰Loose plate flange压力级Pressure rating ; Pressure rating class压力-温度等级Pressure-temperature rating法兰密封面；法兰面Flange facing突面Raised face [RF]凸面Male face [MF]凹面Female face [FMF]榫面Tongue face槽面Groove face环连接面Ring joint face短半径弯头Short radius elbow长半径180º弯头Long radius return短半径180º弯头Short radius return带侧向口的弯头（右向或左向）Side outlet elbow(Right hand or left hand) 双支管弯头Double branch elbow三通Tee异径三通Reducing tee等径三通Straight tee带侧向口的三通（右向或左向）Side outlet tee (Right hand or left hand) 异径三通（分支口为异径）Reducing tee(Reducing on outlet)异径三通（一个直通口为异径）Reducing tee (Reducing on one run)堵头Plug短管Nipple异径短节Reducing nipple异径短节(外螺纹或无螺纹) Swage nippe (选自BS 3800)弯头Elbow异径弯头Reducimg elbow带支座弯头Base elbow长半径弯头Long radius elbow管子（按照标准规格制造的配管用管）Pipe管子（不按照标准规格制造的其他用管) Tube钢管Steel pipe铸铁管Cast iron pipe衬里管Lined pipe复合管Clad pipe碳钢管Carbon steel [C.S.]pipe合金钢管Alloy steel pipe不锈钢管Stainless steel [S.S.]pipe奥氏体不锈钢管Austenitic stainless pipe铁合金钢管Ferritic alloy steel pipe扎制钢管Wrought-steel pipe段铁管Wrought-iron pipe无缝钢管Seamless[SMLS]steel pipe焊接钢管Welded steel pipe电阻焊钢管Electric-resistance-welded steel pipe电熔（弧）焊钢板卷管Electric-fusion (arc)-welded steel-plate pipe 螺旋焊接钢管Spiral welded steel pipe镀锌钢管Galvanized steel pipe热轧无缝钢管Hot-rolling seamless pipe冷拉无缝钢管Cold-drawing seamless pipe水煤气钢管Water-gas steel pipe塑料管Plastic pipe玻璃管Glass tube橡胶管Rubber tube壁厚Wall thickness(WT)壁厚系列号Schcdule number架厚的，加强的Extra heavy; Extra stromg双倍加强的，双倍加厚的Double extra heavy; Double extra strong 预制弯管Fabricated pipe bend跨越弯管( )形Cross-over bend偏置弯管（）形Offset bend锥管螺纹密封焊连接Seal-welded taper pipe threaded joint承插焊连接（接头）Socket welded joint承插连接（接头）Bell and spigot joint焊接接头Welded joint环垫接头Ring joint[RJ]万向接头Universal软钎焊连接（接头）Soldered joint搭接接头Lapped joint外侧厚度切斜角Bevel for outside thickness内侧厚度切斜角Bevel for inside thickness内外侧厚度切斜角Bevel for combined thickness法兰式的Flanged [FLGD]对焊的Butt welded [BW]螺纹的Threaded [THD]承插焊的Socket welded [SW]小端为平的Small end plain [SEP]大端为平的Large end plain [LEP]两端平Both ends plain [BEP]小端带螺纹Small end thread [SET]大端带螺纹Large end thread一端带螺纹One end thread两端带螺纹Both ends thread整体管法兰Integral pipe flange光滑突面Smooth raised face [SRF]法兰面加工Facing finish粗糙度Roughness光滑的Smooth齿形的Serrated均方根Root mean square [RMS]算术平均粗糙高度Arithmetical average roughness height[AARH] HALF COUPLING 单承口管箍1.1 P 管子Pipe1.2.3 MEL 斜接弯头（虾米腰弯头）Mitre elbow1.2.4 REL 异径弯头Reducing elbow1.3 T 三通Tee1.3.1 LT 斜三通Lateral tee1.3.2 RT 异径三通Reducing tee1.4 R 异径管接头（大小头）Reducer1.4.1 CR 同心异径管接头（同心大小头）Concentric reducer 1.4.2 ER 偏心异径管接头（偏心大小头）Eccentric reducer1.5 CPL 管箍Coupling1.5.1 FCPL 双头管箍Full coupling1.5.2 HCPL 单头管箍Half coupling1.5.3 RCPL 异径管箍Reducing coupling1.6 BU 内外螺纹接头Bushing1.7 UN 活接头Union1.8 HC 软管接头Hose coupler1.9 SE 翻边短节Stub end1.10 NIP 短节Pipe nipple or straight nipple1.10.1 SNIP 异径短节Swaged nipple1.11 CP 管帽（封头）Cap1.12 PL 管堵（丝堵）Plug1.13 BLK 盲板Blank1.13.1 SB 8字盲板Spectacle blind (blank)1.14 RP 补强板Reinforcing padHARDNESS 硬度（最大值197）HEAT CONTROL NUMBER 热处理炉号HEAT TREATMENT（热处理），有缝部分填N，无缝部分填A HEX HEAD BUSHING 卜申HEX HEAD PLUG 六角塞头HEX NIPPLE 六角立布HIGH PRESSURE ELBOW 高压弯头HIGH PRESSURE REDUCER 高压异径管HIGH PRESSURE TEE 高压四通hydraulic hose液压软管HJ 环境保护行业标准hose clip软管卡子hose protector软管保护管hot-rolling seamless pipe热轧无缝钢管HR 热轧INNER DIAMETER （简）ID 内径INSERT 变径接头integral pipe flange整体管法兰JIS 日本工业标准jumper hose跨接软管jumper lose connection跨接软管连接器Lap Joint Flanges对焊环松套法兰lap joint flange (LJF) 松套法兰lapped joint搭接接头，松套连接lapped pipe end翻边端large end plain (LEP) 大端为平的1 管道组成件Piping component1.1 管子Pipe管子(按照配管标准规格制造的) pipe管子(不按配管标准规格制造的其他用管) tube钢管steel pipe铸铁管cast iron pipe衬里管lined pipe复合管clad pipe碳钢管carbon steel pipe合金钢管alloy steel pipe不锈钢stainless steel pipe奥氏体不锈钢管austenitic stainless steel pipe铁合金钢管ferritic alloy steel pipe轧制钢管wrought-steel pipe锻铁管wrought-iron pipe无缝钢管seamless (SMLS) steel pipe焊接钢管welded steel pipe电阻焊钢管electric-resistance welded steel pipe电熔（弧）焊钢板卷管electric-fusion (arc)-welded steel-plate pipe 螺旋焊接钢管spiral welded steel pipe镀锌钢管galvanized steel pipe热轧无缝钢管hot-rolling seamless pipe冷拔无缝钢管cold-drawing seamless pipe水煤气钢管water-gas steel pipe塑料管plastic pipe玻璃管glass tube橡胶管rubber tube直管run pipe; straight pipe1.2 管件Fitting弯头elbow异径弯头reducing elbow带支座弯头base elbowk半径弯头long radius elbow短半径弯头short radius elbow长半径180°弯头long radius return短半径180°弯头short radius return带侧向口的弯头（右向或左向）side outlet elbow (right hand or left hand)双支管弯头（形）double branch elbow三通tee异径三通reducing tee等径三通straight tee带侧向口的三通（右向或左向）side outlet tee (right hand or 1eft hand)异径三通（分支口为异径）reducing tee (reducing on outlet)异径三通（一个直通口为异径）reducing tee (reducing on one run)带支座三通base tee异径三通（一个直通口及分支口为异径）reducing tee (reducing on one run and outlet) 异径三通（两个直通口为异径，双头式）reducing tee (reducing on both runs, bull he ad)45°斜三通45°lateral45°斜三通（支管为异径）45°lateral (reducing on branch)45°斜三通(一个直通口为异径) 45°lateral (reducing on one run)45°斜三通(一个直通口及支管为异径) 45°lateral (reducing on one run and branch)Y型三通（俗称裤衩）true “Y”四通cross等径四通straight cross异径四通reducing cross异径四通（一个分支口为异径）reducing cross (reducing on one outlet)异径四通（一个直通口及分支口为异径）reducing cross (reducing on one run and out let)异径四通（两个分支口为异径）reducing cross (reducing on both outlet)异径四通（一个直通口及两个分支口为异径）reducing cross (reducing on one run an d both outlet)异径管reducer同心异径管concentric reducer两端带螺纹both end thread (BET)一端带螺纹one end thread (OET)支管连接branch connection焊接支管branch pipe welded directly to the run pipe法兰端flanged end坡口端beveled end (BE)对焊端butt welded end平端plain end (PE)承插焊端socket welding end螺纹端threaded end (TE)承口bell end焊接端welding end法兰连接（接头）flanged joint对焊连接（接头）butt welded joint螺纹连接，管螺纹连接threaded joint, pipe threaded joint 锥管螺纹密封焊连接seal-welded taper pipe threaded joint 承插焊连接（接头）socket welded joint承插连接（接头）bell and spigot joint环垫接头ring joint (RJ)万向接头universal joint软钎焊连接（接头）soldered joint搭接接头，松套连接lapped joint外侧厚度切斜角bevel for outside thickncss内侧厚度切斜角bevel for inside thickness内外侧厚度切斜角bevel for combined thickness法兰式的flanged (FLGD)对焊的butt welded (BW)螺纹的threaded (THD)承插焊的socket welded (SW)小端为平的small end plain (SEP)大端为平的large end plain (LEP)两端平both ends plain (BEP)小端带螺纹small end thread (SET)大端带螺纹large end thread (LET)多波multiple bellow压力平衡式膨胀节pressure balanced expansion带铰链膨胀节hinged expansion joint轴向位移型膨胀节axial movement type expansion joint 自均衡膨胀节（外加强环）self-equalizing expansion joint 带接杆膨胀节tied expansion joint万向型膨胀节universal type expansion joint球形补偿器ball type expansion joint填函式补偿器slip type (packed type) expansion joint单向滑动填料函补偿器single actionpacked slip joint1.7.2 管道特殊元件Piping Special Element软管接头hose connection (HC)快速接头quick coupling金属软管metal hose橡胶管rubber hose挠性管flexible tube鞍形补强板reinforcing saddles补强板reinforcement pad特殊法兰special flange漏斗funnel排液环drip ring排液漏斗drain funnel插板blank垫环spacer8字盲板spectacle blind; figure 8 blind限流孔板restriction orifice爆破片rupture disk法兰盖贴面protective disc费托立克接头victaulic coupling1.8 端部连接End Connection（水）龙头bibb; bib; faucet抽出液阀（小阀）bleed valve旁路阀by-pass valve软管阀hose valve混合阀mixing valve破真空阀vacuum breaker冲洗阀flush valve第一道阀；根部阀primary valve根部阀root valve总管阀header valve事故切断阀emergency valve1.7 管道特殊件Piping Specialty1.7.1 管道特殊件（组件）粗滤器strainer过滤器filter临时粗滤器（锥型）temporary strainer (cone type)y 型粗滤器y-type strainerT型粗滤器T-type strainer永久过滤器permanent filter丝网粗滤器gauze strainer洗眼器及淋浴器eye washer and shower视镜sight glass阻火器flame arrester喷嘴；喷头spray nozzle取样冷却器sample cooler消声器silencer膨胀节expansion joint波纹膨胀节bellow expansion joint单波single bellow双波double bellow杠杆重锤式lever and weight type引导阀操纵的安全泄气阀pilot operated safety valve复式安全泄气阀twin type safety valve罐底排污阀flush-bottom tank valve电磁阀solenoid valve, solenoid operated valve电动阀electrically operated valve, electric-motor operated valve 气动阀pneumatic operated valve低温用阀cryogenic service valve蒸汽疏水阀steam trap机械式疏水阎mechanical trap浮桶式疏水阀open bucket trap, open top bucket trap浮球式疏水阀float trap倒吊桶式疏水阀inverted bucket trap自由浮球式疏水阀loose float trap恒温式疏水阀thermostatic trap金属膨胀式蒸汽疏水阀metal expansion steam trap液体膨胀式蒸汽疏水阀liquid expansion steam trap双金属膨胀式蒸汽疏水阀bimetallic expansion steam trap压力平衡式恒温疏水阀balanced pressure thermostatic trap热动力式疏水阀thermodynamic trap脉冲式蒸汽疏水阀impulse steam trap放气阀（自动放气阀）air vent valve (automatic air vent valve) （疏水阀用）平板式滑动闸阀slab type sliding gate valve盖阀flat valve换向阀diverting valve, reversing valve热膨胀阀thermo expansion valve自动关闭阀self-closing gate valve自动排液阀self-draining valve管道盲板阀line-blind valve挤压阀squeeze valve（用于泥浆及粉尘等）偏心阀板蝶阀offset disc burerfly valve; eccentric butterfly valve 斜阀盘蝶阀canted disc butterfly valve连杆式蝶阀link butterfly valve8) 柱塞阀piston type valve(9) 旋塞阀plug valve三通旋塞阀three-way plug valve四通旋塞阀four-way plug valve旋塞cock衬套旋塞sleeve cock(10) 隔膜阀diaphragm valve橡胶衬里隔膜阀rubber lined diaphragm valve直通式隔膜阀straight way diaphragm valve堰式隔膜阀weir diaphragm valve(11) 夹紧式胶管阀pinch valve（用于泥浆、粉尘等）(12) 止回阀check valve升降式止回阀lift check valve旋启式止回阀swing check valve, flap check valve 落球式止回阀ball check valve弹簧球式止回阀spring ball check valve双板对夹式止回阀dual plate wafer type check valve 无撞击声止回阀non-slam cheek valve底阀foot valve切断式止回阀stop check valve; non-return valve活塞式止回阀piston check valve斜翻盘止回阀tilting disc check valve蝶式止回阀butterfly check valve1.6.3 其它用途的阀安全泄气阀safety valve (SV)安全泄液阀relief valve (RV)安全泄压阀safety relief valve升杆式（明杆）rising stem (RS)非升杆式（暗杆）non-rising stem (NRS)指示器/限位器indicator/stopper注油器grease injector可更换的阀座环renewable seat ring1.6.2 常用阀(1）闸阀gate valve平行双闸板double disc parallel seat开口楔形闸板split wedge挠性整体楔形闸扳flexible solid wedge整体楔形闸板solid wedge塞型闸阀plug gate valve直通型闸阀through conduit gate valve(2) 截止阀globe valve球心型阀盘globe type disc塞型阀盘plug type disc可转动的阀盘swivel disc(3) 节流闪阀throttle valve针阀needle valve(4) 角阀angle valve(5) Y型阀（Y 型阀体截止阀）Y-valve (Y-body globe valve)(6) 球阀ball valve三通球阀3-way ball valve装有底轴的trunnion mounted耐火型fire safe type浮动球型floating ball type防脱出阀杆blowout proof stem(7) 蝶阀butterfly valve对夹式（薄片型）wafer type凸耳式lug type螺栓连接的阀盖bolted bonnet (BB)活接阀盖（帽）union bonnet (cap)螺栓连接的阀帽bolted cap (BC)焊接阀盖welded bonnet (WB)本体阀杆密封body stem seal石棉安全密封asbestos emenen seal倒密封back seal压力密封的阀盖pressure-tight bonnet动力操纵器powered operator电动操纵器electric motor operator气动操纵器pneumatic operator液压操纵器hydraulic operator快速操纵器quick-acting operator滑动阀杆sliding stem正齿轮传动spur gear operated伞齿轮传动bevel gear operated扳手操作wrench operated链轮chain wheel手轮hand wheel手柄hand lever (handle)气缸（或液压缸）操纵的cylinder operated链条操纵的chain operated等径孔道full bore; full port异径孔道reducing bore, reduced port,venturi port短型short pattern紧凑型（小型）compact type笼式环lantern ring压盖gland阀杆填料stem packing阀盖垫片bonnet gasket斜接弯管mitre bend三节斜接弯管3-piece mitre bend折皱弯管corrugated bend圆度roundness1.4 法兰Flange (FLG）整体管法兰integral pipe flange钢管法兰steel pipe flange螺纹法兰threaded flange滑套法兰（包括平焊法兰）slip-on flange (SO); slip-on wel ding flange承插焊法兰socket welding flange松套法兰lap joint flange (LJF)对焊法兰welding neckflange (WNF)法兰盖blind flange, blind孔板法兰orifice flange异径法兰reducing flange盘座式法兰pad type flange松套带颈法兰loose hubbed flange焊接板式法兰welding plate flange对焊环welding neck collar （与stub end相似）平焊环welding-on collar突缘短节stub end, lap翻边端lapped pipe end松套板式法兰loose plate flange压力级pressure rating, pressure rating class压力—温度等级pressure-temperature rating 法兰密封面，法兰面flange facing突面raised face (RF)凸面male face (MF)凹面female face (FMF)榫面tongue face。

工程英文缩写知识分享

字号：大中小石油化工企业配管工程常用英语缩写1 管子及管件编号缩写中文名称英文名称1.1 P 管子 Pipe1.2 EL 弯头 Elbow1.2.1 ELL 长半径弯头 Long radius elbow1.2.2 ELS 短半径弯头 Short radius elbow1.2.3 MEL 斜接弯头（虾米腰弯头） Mitre elbow1.2.4 REL 异径弯头 Reducing elbow1.3 T 三通 Tee1.3.1 LT 斜三通 Lateral tee1.3.2 RT 异径三通 Reducing tee1.4 R 异径管接头（大小头） Reducer1.4.1 CR 同心异径管接头（同心大小头） Concentric reducer 1.4.2 ER 偏心异径管接头（偏心大小头） Eccentric reducer 1.5 CPL 管箍 Coupling1.5.1 FCPL 双头管箍 Full coupling1.5.2 HCPL 单头管箍 Half coupling1.5.3 RCPL 异径管箍 Reducing coupling1.6 BU 内外螺纹接头 Bushing1.7 UN 活接头 Union1.8 HC 软管接头 Hose coupler1.9 SE 翻边短节 Stub end1.10 NIP 短节 Pipe nipple or straight nipple1.10.1 SNIP 异径短节 Swaged nipple1.11 CP 管帽（封头） Cap1.12 PL 管堵（丝堵） Plug1.13 BLK 盲板 Blank1.13.1 SB 8字盲板 Spectacle blind (blank)1.14 RP 补强板 Reinforcing pad2 法兰编号缩写中文名称英文名称2.1 PLG 法兰 Flange2.1.1 WNF 对焊法兰 Welding neck flange2.1.2 SOF 平焊法兰 Slip-on flange2.1.3 SWF 承插焊法兰 Socket-welding flange2.1.4 T 螺纹法兰 Threaded flange2.1.5 LJ 松套法兰 Lapped joint flange2.1.6 REDF 异径法兰 Reducing flange2.1.7 BF 法兰盖（日法兰） Blind flange2.2 FSF 法兰密封面 Flange scaling face2.2.1 FF 全平面 Flat face2.2.2 RF 凸台面 Raised face2.2.3 MFF 凹凸面 Male and female face2.2.4 LF 凹面 Female face2.2.5 LM 凸面 Male face2.2.6 RJ 环连接面 Ring joint face2.2.7 TG 榫槽面 Tongue and groove face2.2.8 TF 榫面 Tongue face2.2.9 GF 槽面 Groove face3 垫片编号缩写中文名称英文名称3.1 G 垫片 Gasket3.1.1 NMG 非金属垫片 Non-metallic gasket3.1.1.1 AG 石棉垫片 Asbestos gasket3.1.1.2 RG 橡胶垫片 Rubber gasket3.1.1.3 TEG 聚四氟乙烯包复垫片 PTFE envelope gasket 3.1.2 SMG 半金属垫片 Semimetallic gasket3.1.2.1 MJG 金属包垫片 Meta-jacket gasket3.1.2.2 SWG 缠绕式垫片 Spiral wound gasket3.1.3 MG 金属垫片 Metallic gasket3.1.3.1 FMG 金属平垫片 Flat metallic gasket3.1.3.2 SMSG 齿形金属垫片 Solid metal serrated gasket 3.1.3.3 LER 透镜式金属环垫 Lens ring gasket3.1.3.4 OCR 八角形金属环垫 Octagonal ring gasket3.1.3.5 OVR 椭圆形金属环垫 Oval ring gakset3.1.3.6 IR/OR 内外定位环 Inner ring and outer ring3.1.3.7 IR 内定位环 Inner ring3.1.3.8 OR 外定位环 Outer ring4 坚固件编号缩写中文名称英文名称4.1 B 螺栓 Bolt4.1.1 SB 螺柱 Stud bolt4.2 NU 螺母 Nut4.3 TB 花蓝螺母 Turnbuckle4.4 WSR 垫圈 Washer4.4.1 SWSR 弹簧垫圈 Spring washer5 阀门编号缩写中文名称英文名称5.1 GV 闸阀 Gate valve5.2 GLV 截止阀 Globe valve5.3 CHV 止回阀 Check valve5.4 BUV 蝶阀 Butterfly valve5.5 BAV 球阀 Ball valve5.6 PV 旋塞阀 Plug valve (cock)5.7 CV 调节阀 Control valve5.8 SV 安全阀 Safety valve5.9 RV 减压阀 Pressure reducing valve5.10 ST 蒸汽疏水阀 Steam trap5.11 PRV 泄压阀 Pressur relief valve5.12 BV 呼吸阀 Breather valve5.13 NV 针形阀 Needle valve5.14 AV 角阀5.15 DV 隔膜阀5.16 TWV 三通阀5.17 SGV 插板阀6 管道上用的小型设备编号缩写中文名称英文名称6.1 SPR 气液分离器 Separator6.2 FA 阻火器 Flame arrester6.3 SR 过滤器 Strainer6.3.1 SRY Y型过滤器 Y-type strainer6.3.2 SRT T型过滤器 T-type strainer6.3.3 SRB 桶式过滤器 Bucket type strainer6.3.4 TSR 临时过滤器 Temporary strainer6.4 SIL 消声器 Silencer6.5 SG 视镜 Slight glass6.6 SC 取样冷却器 Sample cooler6.7 DF 排液漏斗 Drain funnel6.8 LM 管道混合器 Line mixer6.9 RO 限流孔板 Restriction orifice6.9.1 MO 混合孔板 Mixing orifice6.1 RD 爆破片（爆破膜） Rupture disk6.11 EJ 补偿器 Expansion joint7 隔热、伴热编号缩写中文名称英文名称7.1 INS 隔热 Thermal insulation7.1.1 H 保温 Hot insulation7.1.2 C 保冷 Cold insulation7.1.3 P 防烫伤隔热 Personnel protection insulation 7.2 T&I 伴热 Tracing and insulation7.3 T 管道伴热（冷） Tracing7.3.1 EST 蒸汽外伴热 External steam tracing7.3.2 IST 蒸汽内伴热 Internal steam tracing7.3.3 SJT 蒸汽夹套伴热 Steam-jacket tracing7.3.4 ET 电伴热 Electric tracing8 配管材料和等级编号缩写中文名称英文名称8.1 M 金属材料 Metallic material8.1.1 CS 碳钢 Carbon steel8.1.2 CAS 铸钢 Cast steel8.1.3 FS 锻钢 Forged steel8.1.4 AS 合金钢 Alloy steel8.1.5 SS 不锈钢 Stainless steel8.1.6 AUSTSS 奥氏体不锈钢 Austenitic stainless-steel8.1.7 CI 铸铁 Cast iron8.1.8 MI 可锻铸铁 Malleable iron8.1.9 DI 球墨铸铁 Ductile iron8.1.10 AL 铝 Aluminum8.1.11 BRS 黄铜 Brass8.1.12 BRZ 青铜 Bronze8.1.13 CU 紫铜 Copper8.1.14 LAS 低合金钢 Low alloy steel8.1.15 FLAS 低合金锻钢 Forged low alloy steel8.1.16 CLAS 低合金铸钢 Cast low alloy steel8.2 THK 壁厚 Thickness8.2.1 SCH 表号 Schedule number8.2.2 STD 标准 Standard8.2.3 XS 加强 Extra strong8.2.4 XXS 特强 Double extra strong9 装置布置编号缩写中文名称英文名称9.1 CN 建北 Construction north9.2 E 东 East9.3 W 西 West9.4 S 南 South9.5 N 北 North9.6 H 水平 Horizontal9.7 V 竖直、铅直、直立 Vertical9.8 GRD 地坪 Ground9.9 UG 地下 Underground9.10 BL 装置边界线 Battery limit line9.11 ESEW 事故沐浴洗眼器 Emergency shower and eye washer 9.12 HS 软管站 Hose station9.13 ML 接续分界线 Match line9.14 PS 管道支架（管架） Piping support9.15 PR 管桥 Pipe rack9.16 STRU 构架（构筑物） Structure9.17 BLDG 建筑物 Building9.18 PD 清扫设施 Purge device9.19 PT 池 Pit9.20 SHLT 棚 Shelter9.21 COFF 围堰 Cofferdam9.22 FL 楼板 Floor9.23 PF 平台 Plateform10 尺寸标注编号缩写中文名称英文名称10.1 EL 标高 Elevation10.2 BOP 管底 Bottom of pipe10.3 COP 管中心 Center of pipe10.4 TOP 管顶 Top of pipe10.5 FOB 底平 Flat on bottom10.6 FOT 顶平 Flat on top10.7 CL(屯) 中心线 Center line10.8 TL 切线 Tangent line10.9 SYM 对称的 Symmetrical10.10 BOS 支架底 Bottom of support10.11 TOS 支架顶 Top of support10.12 CL 净距（净空） Clearance10.13 CTC 中心至中心 Center to center10.14 CTF 中心至面 Center to face10.15 CTE 中心至端部 Center to end10.16 ETE 端到端 End to end10.17 FEF 法兰端面 Flange and face10.18 FTF 面到面 Face to face10.19 D 直径 Diameter10.20 DN 公称直径 Nominal diameter10.21 ID 内径 Inside diameter10.22 OD 外径 Outside diameter10.23 DIM 尺寸 Dimension10.24 MAX 最大 Maximum10.25 MIN 最小 Minimum10.26 AVG 平均 Average10.27 APP 约、近似 Approximate10.28 PT.EL 点标高 Point elevation11 图表编号缩写中文名称英文名称11.1 PFD 工艺流程图 Process flow diagram11.2 PID 管道和仪表流程图 Piping & instrument diagram 11.3 COD 接续图 Continued on drawing11.4 DTL 详图 Datail11.5 SPDWG(ISODWG) 管段图 Spool drawing (each line isometric drawing) 11.6 DWGNO 图号 Drawing number11.7 DWGI 所在图号 Drawing identification11.8 LOW 材料表 List of material11.9 MTO 汇料 Material take-off11.10 APPX 附录 Appendix11.11 JOB. No. 工号 Job Number11.12 BEDD 基础工程设计数据 Basic engineering design data 11.13 DEDD 详细工程设计数据 Detail engineering design data 11.14 REV. No. 修改号 Recision number11.15 REFDWG 参考图 Reference drawing11.16 SC 采样接口 Sample connection12 操作方式及工作参数编号缩写中文名称英文名称12.1 AUT 自动 Automatic12.2 ML 手动 Manual control12.3 CHOP 链条操作 Chain operated12.4 CSC 铅封关 Car seal close12.5 CSO 铅封开 Car seal open12.6 LC 锁闭 Lock closed12.7 LO 锁开 Lock open12.8 NC 正常关 Normally close12.9 NO 正常开 Normally open12.10 ATM 大气压 Atmosphere12.11 PN 公称压力 Nominal pressure12.12 A 绝压12.13 G 表压12.14 (T) 温度 Temperature12.15 (P) 压力 Pressure13 施工编号缩写中文名称英文名称13.1 W 焊接 Welding13.1.1 AW 电弧焊 Arc welding13.1.2 GSAW 气体保护电弧焊 Gas shielded-acr welding13.1.3 EFW 电熔焊 Elecric fusion welding13.1.4 ERW 电阻焊 Electric Resistance welding13.1.5 GW 气焊 Gas welding13.1.6 LW 搭接焊 Lap welding13.1.7 BW 对焊 Butt welding13.4.8 TW 定位焊 Tack welding13.1.9 SW 承插焊 Socket welding13.1.10 CW 连续焊 Continuous welding13.1.11 SEW 密封焊 Seal welding13.1.12 SFG 堆焊 Surfacing13.1.13 FW 现场焊接 Field welding13.2 HT 热处理 Heat treatment13.2.1 PH 预热 Preheating13.2.2 SR 应力消除 Stress relief13.2.3 PWHT 焊后热处理 Post weld heat treatment13.3 EIT 检查、探伤和实验 Examination, inspection & testing 13.3.1 VE 外观检查 Visual examination13.3.2 UI (UT) 超声探伤 Ultrasonic inspection (test)13.3.3 RI (RT) 射线探伤 Radiographic inspection (test)13.3.4 MPI (MT) 磁粉探伤 Magnetic particle inspection (test) 13.3.5 LPI (PT) 液体渗透检验 Liquid penterant inspection (test) 13.3.6 HADT 硬度实验 Hardness testing13.3.7 HYDT 水压实验 Hydraulic testing13.3.8 PNET 气压实验 Pneumatic testing13.3.9 CE 焊条 Covered electrode13.3.10 WW 焊丝 Welding wire13.3.11 ASSY 装配、组合 Assembly13.3.12 F 现场 Field13.3.13 F/F 现场制造 Field faricated13.3.14 SF 现场决定 Suit in field13.3.15 CSP 冷紧 Cold spring13.3.16 BCT 螺栓冷紧 Bolt cold tightening13.3.17 BHY 螺栓热紧 Bolt hot tightening13.3.18 CO 清洗口 Clean out13.3.19 ANNY 退火 Annealed13.4 PE 平端面 Plain end13.5 BE 坡口端 Belelled end13.6 THR 螺纹 Thread13.7 HB 布氏硬度 Brinnel hardness13.8 RC 洛氏硬度14 其他编号缩写中文名称英文名称14.1 FDN 基础 Foundation14.2 INF 信息（资料） Information14.3 REF 参考 Reference14.4 REV 修改 Revision14.5 SEQ 序号（顺序） Sequence14.6 W/E 设备带来 With equipment14.7 W/I 仪表带来 With instrument14.8 CM 色标 Colour mark14.9 CA 腐蚀裕度 Corrosion allowance14.10 UTL 公用系统 Utility14.11 UC 公用工程接头 Utility connection14.12 QTY 数量 Quantity14.13 WT 重量 Weight14.14 MHR 工时 Man hour14.15 BC 螺栓分布圆 Bolt circle14.16 HP 高点 High point14.17 LP 低点 Low point14.18 SUC 吸入（口） Suction14.19 DIS 排出（口） Discharge14.20 SO 蒸气吹扫（口） Steam out14.21 NPT 美国标准锥管螺纹 National standard taper pipe thread 14.22 NPS 美国标准直管螺纹 National standard straight pipe thread 14.23 DR 排液 Drain14.24 VT 放气 Vent14.25 RTG （压力）等级 Rating14.26 CL 等级 Class14.27 SMLS 无缝 Seamless14.28 螺旋缝5.7 图面标注绝对标高 abselute elevation海平面标高 over-sea mean level (OSL)标高，立面 elevation (EL)混凝土顶面 top of concrete架顶面 top of support (TOS)钢结构顶面 top of steel梁项面 top of beam (TOB)支撑点 point of suppon (POS)管顶 top of pipe (TOP)管底 bouom of pipe (BOP)沟底 boaom of trench管子内底 invert (inside bottom of pipe)底平 flat on bottom (FOB)顶平 flat on top (FOT)工作点 working point (W.P.)面至面 face to face (F-F)中心至端面 center to end (C-E)中心至面 center to face (C-F)中心至中心.中至中 center to center (C-C)坐标 coordinate坐标原点 origin of coordinate出口中心线 center line of discharge入口中心线 center line of suction中心线 centerline (CL)入口 inlet, suction出口 outlet, discharge排出口 exhaust距离 distance5.8 相关专业的专业词汇5.8.1 工艺(1) 图及表流程图 flow diagram工艺流程图 process flow diagram (PFD)管道及仪表流程图 piping andinstrument flow diagram (PID)公用工程流程图 utility flow diagram (UFD) 管线表 line list; line schedule命名表；管道表 nomenclature设备表 equipment list (schedule)(2) 流体 fluid空气 air仪表空气 instrument air工艺空气 process air低压蒸汽 low pressure steam中压蒸汽 medium pressure steam高压蒸汽 high pressure steam伴热蒸汽 tracing steam饱和蒸汽 saturated steam过热蒸汽 superheated steam氧气 oxygen氢气 hydrogen氮气 nitrogen燃料气 fuel gas天然气 natural gas火炬气 flare gas酸性气 sour gas液化石油气 liquefired petroleum gas (LPG) 氨气 ammonia gas冷却水 cooling循环水 circulating water锅炉给水 boiler feed water热水 hot water蒸汽冷凝水 steam condensate盐水 brine工艺水 process water化学污水 chemical sewage防腐剂 corrosion inhibitor重油 heavy oil石脑油 naphtha燃料油 fuel oil润滑油 lubricating oil密封油 sealing oil冷冻剂 refrigerant载热体 heating medium溶剂 solvent溶液 solution母液 mother liquor单体 monomer聚合物 polymer均聚物 homopolymer共聚物 copolymer工艺液体 process liquid工艺气体 process gas硫酸 sulphuric acid盐酸 chlorhydric acid硝酸 nitric acid烧碱 caustic soda(3) 流体特性 fluid characteristics 蒸汽压 vapor pressure临界温度 critical temperature临界点 critical point临界压力 critical pressure比热 specific heat湿度 humidity密度 density比重 specific gravity粘度 viscosity闪点 flash point融点 melting point凝固点 freezing point浓度 concentration爆炸极限 limit of explosion有毒的 toxic可燃的；易燃的 flammable(4) 其它回收 recovery再生 regeneration循环 cireulatlon再循环；再生 recycle补充 make-up制备 preparation蒸汽吹扫 steaming out吹扫 purge抽空；排空 evacuation吹出 blow-off排污 blow down破真空 vacuum breaker大气腿 barometric leg备用 stand-by化学清洗 chemical cleaning净正吸入压头 net positive suction head (NPSH) 进料 feed成品 product污染 contamination大气污染 atmospheric pollution环境温度 ambient temperature5.8.2 建筑、结构建筑物 building钢结构 steel structure已有钢结构 existing steel structure钢筋混凝土结构 reinforced concrete construction 楼面 floor平台 platform (PF)地面 ground level栏杆 handrail楼梯 stair. stair way直梯 ladder柱 column; post; stanchion基础 foundation; footing粱 beam斜撑；支撑 bracing桁架；主粱 girder构件 member隔墙 partition wall墙 wall篦子板 grate; grating吊装孔 erection opening吊梁 hoisting beam棚 shelter窗 window天窗 skylight门 door防火门 fire door地漏 floor drain防火层 fire-proofing总图 general plot plan路肩 shoulder桩 pile灌浆 grouting风荷载 wind load雪荷载 snow load动力荷载 dynamic load静荷载 dead load活荷载 live load风速 wind velocity主导风向 most frequent wind direction5.8.3 仪表盘（操作盘） panel就地盘 local panel仪表盘 instrument panel常开 normally open常闭 normally closed电缆槽（架） cable tray (channel); cable rack 仪表电缆槽（架） instrument cable tray (duct) 压力计 manometer; pressure gauge热电偶 thermocouple温度计 thermometer液位计 level gauge玻璃液位计 gage glass温度计保护管 thermowell流量计 flow meter孔板 orifice变送器 transmitter联锁 interlock仪器；设备 apparatus仪器分析 instrumental analysis自动分析 automatic analysis气体分析 gas analysis化学分析 chemical analysis气相色谱仪 gas chromatograph液相色谱仪 liquid chromatograph质谱分析 mass spectrometric analysis5.8.4 电气危险区划分 hazardous area classification危险区平面图 hazardous area plan电气盘 electrical panel配电盘 switch board电缆沟 cable trench电流 current直流 direct current交流 alternating current频率 frequency相位 phase功率因数 power factor电压 voltage电阻 resistance电容 capacitance静电 static electricity接地 grounding; easthing照明 lighting; illumination避雷针 lightning preventer电话 telephone电线 wire接线箱（盒） junction box导线管 conduit tube5.8.5 设备固定鞍座 fixed saddle滑动鞍座 sliding saddle管口 nozzle人孔 manhole (MH)手孔 handhole (HH)检查孔 inspection hole吊柱 davit切线 tangent line焊接线 weldingiine件号 part humbet椭圆形封头 ellipsoidal head加强圈 reinforcing ring接地板 earth lug吊耳 lifting lug气缸 cylinder轴 shaft轴承 bearing附件，附属设备 accessory编位号设备 itemized equipment无位号设备 non-itemized equipment 5.8.6 水道(1) 流体原水 raw water硬水 hard water软水 soft water饮用水 potable water循环冷却水给水 cooling water supply 循环冷却水回水 cooling water return 脱盐水 demineralized water苦咸水（碱性水） brackish water生活污水 sanitary sewer工业废水 industrial waste water雨水 rain water污染雨水 contaminated rain water消防水 fire water(2) 装置、设施软化装置 softener沉淀器 settler沉淀池 clarifier脱盐装置 demineralizer水处理 water traatment冷却塔 cooling tower中和池 neutralization tank化粪池 septic tank渗滤井 soak-away pit井 well阀井 valve pit清扫口 clean out（3）消防消火栓 hydrant水炮 water monitor洒水器 sprinkler水喷淋 watering灭火器 fire extinguisher消防水泵 fire pump消防车 fire fighting truck泡沫消防 foam fire-fighting泡沫栓 foam hydrant泡沫炮 foam monitor消防软管接头 fire hose connection管道等级及材料统计（中英文对照）管道等级及材料统计4.1 管道材料规定 Piping Material Specification管道等级 piping class; piping classification管道等级号 class designation公称直径 nominal diameter (DN); nominal (pipe) size 公称压力 nominal pressure (PN)压力级，等级，类别 class (CL)低压 low pressure (L.P.)中压 medium pressure (M.P.)高压 high pressure (H.P.)大气压 atmosphere (ATM)真空 vacuum工作压力 operating pressure; working pressure设计压力 design pressure工作温度 operating temperature设计温度 design temperature环境温度 ambient temperature腐蚀裕量 corrosion allowance管道附件 piping attachment管道元件 piping element壁厚 wall thickness (WT)壁厚系列号 schedule number (SCH. No.)加厚的.加强的 extra heavy, extra strong双倍加厚的，双倍加强的 double extra heavy, double extra strong通用连接组 typieal installation分组（类）形式（如管道等级表） block form数据库 data base文件 file4.2 材料统计 Material Take-off (MTO)汇总表 summary sheet材料表 bill of material (BM)综合管道材料表 consolidated piping material summary sheet (CPMSS) 统计材料准确度 accuracy of take-off材料情况报告 material status report (MSR)散装材料 bulk material编位号的 itemized代码 code number短代码 short code数量 quantity (QTY)重力 weight净重 net weight毛重 gross weight管道用紧固件及螺纹（中英文对照）2.1 紧固件螺栓 bolt六角头螺栓 hexagonal head bolt方头螺栓 square head bolt螺柱，双头螺栓 stud bolt环头螺检 eye bolt沉头螺栓 countersunk (head) screw地脚螺栓 anchor bolt; foundation bolt松紧螺旋扣（花篮螺丝） turnbuckleU形螺栓 U-boltT形螺栓 T-bolt圆头螺钉 round head bolt机螺栓，机螺钉 maehine bolt顶开螺栓，顶起螺栓 Jack screw自攻螺钉 self tapping screw膨胀螺栓 expansion bolt粗制的 coarse精制的 finished. fine螺母 nut六角螺母 hexagonal nut方螺母 square nut蝶形螺母 wing nut扁螺母 flat nut锁紧螺母 lock nut垫圈 washer平垫圈 plain washer球面垫圈 spherical washer弹簧垫圈 spring washer方垫圈 square washer斜垫圈 slant washer销轴 pinned shan销 pin开口销 cotter pin定位销 dowel pin带孔销 pin with hole圆锥销 taper pin铆钉 rivet键 key2.2 螺纹左螺纹left hand thread右螺纹 right hand thread管螺纹 pipe thread锥管螺纹 taper pipe thread直管螺纹straight pipe thread梯形螺纹 trapezoid thread螺距pitch of thread粗牙螺纹coarse thread细牙螺纹 fine thread特细牙螺纹extra fine thread通长螺纹full thread惠氏螺纹whitworth thread公制螺纹 metric ibread美国标准锥管螺纹 American standard taper pipe thread (NPT) 螺孔 tap管道组成件专业英语(中英文对照)1 管道组成件 Piping component1.1 管子 Pipe管子(按照配管标准规格制造的) pipe管子(不按配管标准规格制造的其他用管) tube 钢管 steel pipe铸铁管 cast iron pipe衬里管 lined pipe复合管 clad pipe碳钢管 carbon steel pipe合金钢管 alloy steel pipe。

【精品】管件常用英文词汇及缩写I

弯头joint弯头anglefittings；bentpipe；elbow；knee 弯头扳手bent—handlewrench；bentspanner 弯头车刀angulartool弯头持针钳curvedneedleholders弯头刀架kneetool弯头道钉brob弯头管swanneck弯头键gibheadkey弯头接合knee—joint弯头螺栓boltwithoneendbentback弯头锁紧螺母elbowjamunt弯头套管elbowunion弯头套筒扳手offsetsocketwrench弯头脱水器elbowseparator弯头芯盒elbowcorebox活接活接loosejoint活接地swingingearth活接结合articulatedjoint活接联接器jointcoupling活接三通uniontee活接头articulation;unionswivel；union活接头螺母unionnut活接头螺栓swingbolt活接头套管unionthimble活接卸槽articulatedchute（浇混凝土用的）三通三通teebend；teebranch;teejoint；teeconneetion；teefitting;wye;Y；yo ke三通玻璃栓three—wayglassstopcock三通道放大器three—channelamplifier;three-pathamplifier三通道自动驾驶仪three-dimensionalautopilot三通电缆分线盒three—waycouplingbox三通阀teevalve；three—portvalve;three—wayvalve；triplevalve三通阀盖triple-valvecap三通阀活塞triple—valvepiston三通阀联箱threewayvalvemenifold三通阀体triplebody;triple-valvebody三通管singlesweeptee；T—branch(pipe)；three—limbtube三通管接头teepipecoupling三通横长horizontallengthoftee三通换向旋塞three—wayreversingcock三通活栓three—waycock三通货协定tripartiescurrencyagreement三通接头teecoupling;teefitting;teeunion;three—waypiece；three—way connection三通接线夹three—wayconnector三通开关three—waycock三通控制阀three-waycontrolvalve三通连接teejunction三通路循环器three-terminalcirculator三通式热风炉three—passstove三通天线转发开关triplexer三通筒triplecylinder三通筒垫密片triple—cylindergasket三通弯头three-wayelbow三通旋塞teecock；three-waycock;three-throwtap三通循环器three—terminalcirculator三通液体流量计teefluidflowmeter三通闸阀trebleportedslidevalve直通直通directconnection；straightin;straightbore；through；feed（-）th rough;once—through直通拨号throughdial（l)ing直通测量线路end—to—endmeasurement直通单向阀in-linecheckvalve；straightcheckvalve;straightwaycheckval ve直通道路throughroad直通的throughandthrough直通地deadearth;deadground直通垫外底throughmidsole直通电报telex直通电报通信telexcommunication直通电流throughcurrent直通电流偏置throughcurrentbias直通电路directcircuit直通阀passvalve;straight—throughvalve;straightwayvalve;throughval ve直通干馏炉throughretort直通锅炉once-throughboiler直通换料once-throughrefuelling直通回路straightcircuit直通汇接呼叫制straightforwardjunctionworking直通监控throughsupervision直通接头straightcoupling;straightfitting直通接线装置throughjoint直通街道throughexpressway；throughstreet；throughway直通进位standingcarry直通开关globecock直通空气制动阀straightairbrakevalve直通空气制动器straightairbrake直通快动阀straight-throughfastactingvalve直通连接straight—throughjoint直通裂化straight—throughcracking直通流动straightthroughflowS型弯管“S”bend单侧偏置90º弯管Singleoffset“U”bendU型弯管“U”bend双偏置U型膨胀弯管Doubleoffsetexpansion“U"bend 斜接弯头Mitreelbow斜接弯Mitrebend三节斜接管4-piecemitrebend折皱弯管Corrugatedbend法兰法兰端Flangedend坡口端；对焊端Beveledend[BEV。

化工管件英文缩写汇总

1管子及管件编号缩写中文名称英文名称1.1P 管子Pipe1.2EL 弯头Elbow1.2.1ELL 长半径弯头Long radius elbow1.2.2ELS 短半径弯头Short radius elbow1.2.3MEL斜接弯头（虾米腰弯头）Mitre elbow1.2.4REL 异径弯头Reducing elbow1.3T 三通Tee1.3.1LT 斜三通Lateral tee1.3.2RT 异径三通Reducing tee1.4R异径管接头（大小头）Reducer1.4.1CR同心异径管接头（同心大小头）Concentric reducer 1.4.2ER偏心异径管接头（偏心大小头）Eccentric reducer 1.5CPL 管箍Coupling1.5.1FCPL 双头管箍Full coupling1.5.2HCPL 单头管箍Half coupling1.5.3RCPL 异径管箍Reducing coupling1.6BU内外螺纹接头Bushing1.7UN 活接头Union1.8HC 软管接头Hose coupler1.10NIP 短节Pipe nipple or straight nipple1.10.1SNIP 异径短节Swaged nipple1.11CP管帽（封头）Cap1.12PL管堵（丝堵）Plug1.13BLK 盲板Blank1.13.1SB 8 字盲板Spectacle blind （ blank）1.14RP 补强板Reinforcing pad2法兰编号缩写中文名称英文名称2.1PLG 法兰Flange2.1.1WNF 对焊法兰Welding neck flange 2.1.2SOF 平焊法兰Slip-on flange2.1.3SWF 承插焊法兰Socket-welding flange 2.1.4T 螺纹法兰Threaded flange2.1.5LJ 松套法兰Lapped joint flange2.1.6REDF 异径法兰Reducing flange2.1.7BF 法兰盖（日法兰）Blind flange2.2FSF 法兰密封面Flange scaling face2.2.1FF 全平面Flat face2.2.2RF 凸台面Raised face2.2.5LM 凸面Male face2.2.6RJ 环连接面Ring joint face2.2.7TG 榫槽面Tongue a nd groove face2.2.8TF 榫面Tongue face2.2.9GF 槽面Groove face3垫片编号缩写中文名称英文名称3.1G 垫片Gasket3.1.1NMG 非金属垫片Non-metallic gasket3.1.1.1AG 石棉垫片Asbestos gasket3.1.1.2RG 橡胶垫片Rubber gasket3.1.1.3TEG 聚四氟乙烯包复垫片PTFE envelope gasket 3.1.2SMG 半金属垫片Semimetallic gasket3.1.2.1MJG 金属包垫片Meta-jacket gasket3.1.2.2SWG 缠绕式垫片Spiral wound gasket3.1.3MG 金属垫片Metallic gasket3.1.3.1FMG 金属平垫片Flat metallic gasket3.1.3.2SMSG 齿形金属垫片Solid metal serrated gasket 3.1.3.3LER 透镜式金属环垫Lens ring gasket3.1.3.4OCR 八角形金属环垫Octagonal ring gasket3.1.3.5OVR 椭圆形金属环垫Oval ring gakset3.1.3.6IR/OR 内外定位环Inner ring a nd outer ring3.1.3.7IR 内定位环Inner ring3.1.3.8OR 外定位环Outer ring4坚固件编号缩写中文名称英文名称4.1 B 螺栓Bolt4.1.1SB 螺柱Stud bolt4.2NU 螺母Nut4.3TB 花蓝螺母Turnbuckle4.4WSR 垫圈Washer4.4.1SWSR 弹簧垫圈Spring washer 5阀门编号缩写中文名称英文名称5.1GV 闸阀Gate valve5.2GLV 截止阀Globe valve5.3CHV 止回阀Check valve5.4BUV 蝶阀Butterfly valve5.5BAV 球阀Ball valve5.6PV 旋塞阀Plug valve （ cock）5.7CV 调节阀Control valve5.8SV 安全阀Safety valve5.9RV 减压阀Pressure reducing valve 5.11PRV 泄压阀Pressur relief valve5.12BV 呼吸阀Breather valve5.13NV 针形阀Needle valve5.14AV角阀5.15DV隔膜阀5.16TWV三通阀5.17SGV插板阀6管道上用的小型设备编号缩写中文名称英文名称6.1SPR气液分离器Separator6.2FA 阻火器Flame arrester6.3SR 过滤器Strainer6.3.1SRY Y 型过滤器Y-type strainer6.3.2SRT T 型过滤器T-type strainer6.3.3SRB 桶式过滤器Bucket type strainer 6.3.4TSR 临时过滤器Temporary strainer 6.4SIL 消声器Silencer6.5SG 视镜Slight glass6.6SC 取样冷却器Sample cooler6.7DF 排液漏斗Drain funnel6.9.1 MO 混合孔板Mixing orifice6.1 RD爆破片（爆破膜）Rupture disk6.11 EJ 补偿器Expansion joint7隔热、伴热编号缩写中文名称英文名称7.1INS 隔热Thermal insulation7.1.1H 保温Hot insulation7.1.2 C 保冷Cold insulation7.1.3P 防烫伤隔热Personnel protection insulation 7.2T&I 伴热Tracing a nd insulation7.3T管道伴热（冷）Tracing7.3.1EST 蒸汽外伴热External steam tracing7.3.21ST 蒸汽内伴热Internal steam tracing7.3.3SJT 蒸汽夹套伴热Steam-jacket tracing7.3.4ET 电伴热Electric tracing8配管材料和等级编号缩写中文名称英文名称8.1M 金属材料Metallic material8.1.1CS 碳钢Carbon steel8.1.2CAS 铸钢Cast steel8.1.3FS 锻钢Forged steel8.1.5SS 不锈钢Stainless steel8.1.6AUSTSS 奥氏体不锈钢Austenitic stainless-steel 8.1.7CI 铸铁Cast iron8.1.8MI 可锻铸铁Malleable iron8.1.9DI 球墨铸铁Ductile iron8.1.10AL 铝Aluminum8.1.11BRS 黄铜Brass8.1.12BRZ 青铜Bronze8.1.13CU 紫铜Copper8.1.14LAS 低合金钢Low alloy steel8.1.15FLAS 低合金锻钢Forged low alloy steel 8.1.16CLAS 低合金铸钢Cast low alloy steel8.2THK 壁厚Thickness8.2.1SCH 表号Schedule number8.2.2STD 标准Standard8.2.3XS 加强Extra strong8.2.4XXS 特强Double extra strong9装置布置编号缩写中文名称英文名称9.1CN 建北Construction north9.3W 西West9.4S 南South9.5N 北North9.6H 水平Horizontal9.7V竖直、铅直、直立Vertical9.8GRD 地坪Ground9.9UG 地下Underground9.10BL 装置边界线Battery limit line9.11ESEW 事故沐浴洗眼器Emergency shower a nd eye washer 9.12HS 软管站Hose station9.13ML接续分界线Match line9.14PS 管道支架（管架）Piping support9.15PR 管桥Pipe rack9.16STRU 构架（构筑物）Structure9.17BLDG 建筑物Building9.18PD 清扫设施Purge device9.19PT 池Pit9.20SHLT 棚Shelter9.21COFF 围堰Cofferdam9.22FL 楼板Floor9.23PF 平台Plateform10尺寸标注编号缩写中文名称英文名称10.1EL 标高Elevation10.2BOP 管底Bottom of pipe10.3COP 管中心Center of pipe10.4TOP 管顶Top of pipe10.5FOB 底平Flat on bottom10.6FOT 顶平Flat on top10.7•（屯）中心线Center line10.8TL 切线Tangent line10.9SYM 对称的Symmetrical10.10BOS 支架底Bottom of support 10.11TOS 支架顶Top of support 10.12CL 净距（净空）Clearance10.13CTC 中心至中心Center to center 10.14CTF 中心至面Center to face 10.15CTE 中心至端部Center to end 10.16ETE 端到端End to end10.17FEF 法兰端面Flange a nd face 10.18FTF 面到面Face to face10.19 D 直径Diameter10.20DN 公称直径Nominal diameter10.22OD 外径Outside diameter10.23DIM 尺寸Dimension10.24MAX 最大Maximum10.25MIN 最小Minimum10.26AVG 平均Average10.27APP 约、近似Approximate10.28PT.EL 点标高Point elevation11图表编号缩写中文名称英文名称11.1PFD 工艺流程图Process flow diagram11.2PID 管道和仪表流程图Piping & instrument diagram 11.3COD 接续图Continued on drawing11.4DTL 详图Datail11.5SPDWG(ISODWG)管段图Spool drawing ( each line isometric drawing) 11.6DWGNO 图号Drawing number11.7DWGI 所在图号Drawing identification11.8LOW 材料表List of material11.9MTO 汇料Material take-off11.10APPX 附录Appendix11.11JOB. No.工号Job Number11.12BEDD 基础工程设计数据Basic engineering design data11.13DEDD 详细工程设计数据Detail engineering design data 11.14REV. No.修改号Recision number11.15REFDWG 参考图Reference drawing11.16SC 采样接口Sample connection12操作方式及工作参数编号缩写中文名称英文名称12.1AUT 自动Automatic12.2ML 手动Manual control12.3CHOP 链条操作Chain operated12.4CSC 铅封关Car seal close12.5CSO 铅封开Car seal open12.6LC 锁闭Lock closed12.7LO 锁开Lock open12.8NC 正常关Normally close12.9NO 正常开Normally open12.10ATM 大气压Atmosphere12.11PN 公称压力Nominal pressure12.12A绝压12.13G表压12.14（ T）温度Temperature13施工编号缩写中文名称英文名称13.1W 焊接Welding13.1.1AW 电弧焊Arc welding13.1.2GSAW 气体保护电弧焊Gas shielded-acr welding 13.1.3EFW 电熔焊Elecric fusion welding13.1.4ERW 电阻焊Electric Resistance welding13.1.5GW 气焊Gas welding13.1.6LW 搭接焊Lap welding13.1.7BW 对焊Butt welding13.1.8TW 定位焊Tack welding13.1.9SW 承插焊Socket welding13.1.10CW 连续焊Continuous welding13.1.11SEW 密封焊Seal welding13.1.12SFG 堆焊Surfacing13.1.13FW 现场焊接Field welding13.2HT 热处理Heat treatment13.2.1PH 预热Preheating13.2.2SR 应力消除Stress relief13.2.3PWHT 焊后热处理Post weld heat treatment13.3EIT 检查、探伤和实验Examination, inspection & testing 13.3.1VE 外观检查Visual examination13.3.2UI （ UT ）超声探伤Ultrasonic inspection （test）13.3.3RI （ RT）射线探伤Radiographic inspection （ test）13.3.4MPI （ MT）磁粉探伤Magnetic particle inspection （ test）13.3.5LPI （ PT）液体渗透检验Liquid penterant inspection （ test）13.3.6HADT 硬度实验Hardness testing13.3.7HYDT 水压实验Hydraulic testing13.3.8PNET 气压实验Pneumatic testing13.3.9CE 焊条Covered electrode13.3.10WW 焊丝Welding wire13.3.11ASSY 装配、组合Assembly13.3.12 F 现场Field13.3.13F/F 现场制造Field faricated13.3.14SF 现场决定Suit in field13.3.15CSP 冷紧Cold spring13.3.16BCT 螺栓冷紧Bolt cold tightening13.3.17BHY 螺栓热紧Bolt hot tightening13.3.18CO 清洗口Clean out13.3.19ANNY 退火Annealed13.4PE 平端面Plain end13.5BE 坡口端Belelled end13.6THR 螺纹Thread13.8 RC洛氏硬度14其他编号缩写中文名称英文名称14.1FDN 基础Foundation14.2INF 信息（资料）Information14.3REF 参考Reference14.4REV 修改Revision14.5SEQ 序号（顺序）Sequence14.6W/E 设备带来With equipment 14.7W/I 仪表带来With instrument 14.8CM 色标Colour mark14.9CA 腐蚀裕度Corrosion allowance 14.10UTL 公用系统Utility14.11UC 公用工程接头Utility connection 14.12QTY 数量Quantity14.13WT 重量Weight14.14MHR 工时Man hour14.15BC 螺栓分布圆Bolt circle14.16HP 高点High point14.17LP 低点Low point14.20SO 蒸气吹扫（口）Steam out14.21NPT 美国标准锥管螺纹National standard taper pipe thread 14.22NPS 美国标准直管螺纹National standard straight pipe thread 14.23DR 排液Drain14.24VT 放气Vent14.25RTG （压力）等级Rating14.26CL 等级Class14.27SMLS 无缝Seamless。

石油化工企业配管工程常用英语缩写

石油化工企业配管工程常用英语缩写1 管子及管件编号缩写中文名称英文名称1.1 P 管子Pipe1.2 EL 弯头Elbow1.2.1 ELL 长半径弯头Long radius elbow1.2.2 ELS 短半径弯头Short radius elbow1.2.3 MEL 斜接弯头（虾米腰弯头）Mitre elbow1.2.4 REL 异径弯头Reducing elbow1.3 T 三通Tee1.3.1 LT 斜三通Lateral tee1.3.2 RT 异径三通Reducing tee1.4 R 异径管接头（大小头）Reducer1.4.1 CR 同心异径管接头（同心大小头）Concentric reducer 1.4.2 ER 偏心异径管接头（偏心大小头）Eccentric reducer 1.5 CPL 管箍Coupling1.5.1 FCPL 双头管箍Full coupling1.5.2 HCPL 单头管箍Half coupling1.5.3 RCPL 异径管箍Reducing coupling1.6 BU 内外螺纹接头Bushing1.7 UN 活接头Union1.8 HC 软管接头Hose coupler1.9 SE 翻边短节Stub end1.10 NIP 短节Pipe nipple or straight nipple1.10.1 SNIP 异径短节Swaged nipple1.11 CP 管帽（封头）Cap1.12 PL 管堵（丝堵）Plug1.13 BLK 盲板Blank1.13.1 SB 8字盲板Spectacle blind (blank)1.14 RP 补强板Reinforcing pad2 法兰编号缩写中文名称英文名称2.1 PLG 法兰Flange2.1.1 WNF 对焊法兰Welding neck flange2.1.2 SOF 平焊法兰Slip-on flange2.1.3 SWF 承插焊法兰Socket-welding flange2.1.4 T 螺纹法兰Threaded flange2.1.5 LJ 松套法兰Lapped joint flange2.1.6 REDF 异径法兰Reducing flange2.1.7 BF 法兰盖（日法兰）Blind flange2.2 FSF 法兰密封面Flange scaling face2.2.1 FF 全平面Flat face2.2.2 RF 凸台面Raised face2.2.3 MFF 凹凸面Male and female face2.2.4 LF 凹面Female face2.2.5 LM 凸面Male face2.2.6 RJ 环连接面Ring joint face2.2.7 TG 榫槽面Tongue and groove face2.2.8 TF 榫面Tongue face2.2.9 GF 槽面Groove face3 垫片编号缩写中文名称英文名称3.1 G 垫片Gasket3.1.1 NMG 非金属垫片Non-metallic gasket3.1.1.1 AG 石棉垫片Asbestos gasket3.1.1.2 RG 橡胶垫片Rubber gasket3.1.1.3 TEG 聚四氟乙烯包复垫片PTFE envelope gasket 3.1.2 SMG 半金属垫片Semimetallic gasket3.1.2.1 MJG 金属包垫片Meta-jacket gasket3.1.2.2 SWG 缠绕式垫片Spiral wound gasket3.1.3 MG 金属垫片Metallic gasket3.1.3.1 FMG 金属平垫片Flat metallic gasket3.1.3.2 SMSG 齿形金属垫片Solid metal serrated gasket 3.1.3.3 LER 透镜式金属环垫Lens ring gasket3.1.3.4 OCR 八角形金属环垫Octagonal ring gasket3.1.3.5 OVR 椭圆形金属环垫Oval ring gakset3.1.3.6 IR/OR 内外定位环Inner ring and outer ring3.1.3.7 IR 内定位环Inner ring3.1.3.8 OR 外定位环Outer ring4 坚固件编号缩写中文名称英文名称4.1 B 螺栓Bolt4.1.1 SB 螺柱Stud bolt4.2 NU 螺母Nut4.3 TB 花蓝螺母Turnbuckle4.4 WSR 垫圈Washer4.4.1 SWSR 弹簧垫圈Spring washer5 阀门编号缩写中文名称英文名称5.1 GV 闸阀Gate valve5.2 GLV 截止阀Globe valve5.3 CHV 止回阀Check valve5.4 BUV 蝶阀Butterfly valve5.5 BAV 球阀Ball valve5.6 PV 旋塞阀Plug valve (cock)5.7 CV 调节阀Control valve5.8 SV 安全阀Safety valve5.9 RV 减压阀Pressure reducing valve5.10 ST 蒸汽疏水阀Steam trap5.11 PRV 泄压阀Pressur relief valve5.12 BV 呼吸阀Breather valve5.13 NV 针形阀Needle valve5.14 AV 角阀5.15 DV 隔膜阀5.16 TWV 三通阀5.17 SGV 插板阀6 管道上用的小型设备编号缩写中文名称英文名称6.1 SPR 气液分离器Separator6.2 FA 阻火器Flame arrester6.3 SR 过滤器Strainer6.3.1 SRY Y型过滤器Y-type strainer6.3.2 SRT T型过滤器T-type strainer6.3.3 SRB 桶式过滤器Bucket type strainer6.3.4 TSR 临时过滤器Temporary strainer6.4 SIL 消声器Silencer6.5 SG 视镜Slight glass6.6 SC 取样冷却器Sample cooler6.7 DF 排液漏斗Drain funnel6.8 LM 管道混合器Line mixer6.9 RO 限流孔板Restriction orifice6.9.1 MO 混合孔板Mixing orifice6.1 RD 爆破片（爆破膜）Rupture disk6.11 EJ 补偿器Expansion joint7 隔热、伴热编号缩写中文名称英文名称7.1 INS 隔热Thermal insulation7.1.1 H 保温Hot insulation7.1.2 C 保冷Cold insulation7.1.3 P 防烫伤隔热Personnel protection insulation 7.2 T&I 伴热Tracing and insulation7.3 T 管道伴热（冷）Tracing7.3.1 EST 蒸汽外伴热External steam tracing7.3.2 IST 蒸汽内伴热Internal steam tracing7.3.3 SJT 蒸汽夹套伴热Steam-jacket tracing7.3.4 ET 电伴热Electric tracing8 配管材料和等级编号缩写中文名称英文名称8.1 M 金属材料Metallic material8.1.1 CS 碳钢Carbon steel8.1.2 CAS 铸钢Cast steel8.1.3 FS 锻钢Forged steel8.1.4 AS 合金钢Alloy steel8.1.5 SS 不锈钢Stainless steel8.1.6 AUSTSS 奥氏体不锈钢Austenitic stainless-steel8.1.7 CI 铸铁Cast iron8.1.8 MI 可锻铸铁Malleable iron8.1.9 DI 球墨铸铁Ductile iron8.1.10 AL 铝Aluminum8.1.11 BRS 黄铜Brass8.1.12 BRZ 青铜Bronze8.1.13 CU 紫铜Copper8.1.14 LAS 低合金钢Low alloy steel8.1.15 FLAS 低合金锻钢Forged low alloy steel8.1.16 CLAS 低合金铸钢Cast low alloy steel8.2 THK 壁厚Thickness8.2.1 SCH 表号Schedule number8.2.2 STD 标准Standard8.2.3 XS 加强Extra strong8.2.4 XXS 特强Double extra strong9 装置布置编号缩写中文名称英文名称9.1 CN 建北Construction north9.2 E 东East9.3 W 西West9.4 S 南South9.5 N 北North9.6 H 水平Horizontal9.7 V 竖直、铅直、直立Vertical9.8 GRD 地坪Ground9.9 UG 地下Underground9.10 BL 装置边界线Battery limit line9.11 ESEW 事故沐浴洗眼器Emergency shower and eye washer 9.12 HS 软管站Hose station9.13 ML 接续分界线Match line9.14 PS 管道支架（管架）Piping support9.15 PR 管桥Pipe rack9.16 STRU 构架（构筑物）Structure9.17 BLDG 建筑物Building9.18 PD 清扫设施Purge device9.19 PT 池Pit9.20 SHLT 棚Shelter9.21 COFF 围堰Cofferdam9.22 FL 楼板Floor9.23 PF 平台Plateform10 尺寸标注编号缩写中文名称英文名称10.1 EL 标高Elevation10.2 BOP 管底Bottom of pipe10.3 COP 管中心Center of pipe10.4 TOP 管顶Top of pipe10.5 FOB 底平Flat on bottom10.6 FOT 顶平Flat on top10.7 CL(屯) 中心线Center line10.8 TL 切线Tangent line10.9 SYM 对称的Symmetrical10.10 BOS 支架底Bottom of support10.11 TOS 支架顶Top of support10.12 CL 净距（净空）Clearance10.13 CTC 中心至中心Center to center10.14 CTF 中心至面Center to face10.15 CTE 中心至端部Center to end10.16 ETE 端到端End to end10.17 FEF 法兰端面Flange and face10.18 FTF 面到面Face to face10.19 D 直径Diameter10.20 DN 公称直径Nominal diameter10.21 ID 内径Inside diameter10.22 OD 外径Outside diameter10.23 DIM 尺寸Dimension10.24 MAX 最大Maximum10.25 MIN 最小Minimum10.26 AVG 平均Average10.27 APP 约、近似Approximate10.28 PT.EL 点标高Point elevation11 图表编号缩写中文名称英文名称11.1 PFD 工艺流程图Process flow diagram11.2 PID 管道和仪表流程图Piping & instrument diagram11.3 COD 接续图Continued on drawing11.4 DTL 详图Datail11.5 SPDWG(ISODWG) 管段图Spool drawing (each line isometric drawing) 11.6 DWGNO 图号Drawing number11.7 DWGI 所在图号Drawing identification11.8 LOW 材料表List of material11.9 MTO 汇料Material take-off11.10 APPX 附录Appendix11.11 JOB. No. 工号Job Number11.12 BEDD 基础工程设计数据Basic engineering design data 11.13 DEDD 详细工程设计数据Detail engineering design data 11.14 REV. No. 修改号Recision number11.15 REFDWG 参考图Reference drawing11.16 SC 采样接口Sample connection12 操作方式及工作参数编号缩写中文名称英文名称12.1 AUT 自动Automatic12.2 ML 手动Manual control12.3 CHOP 链条操作Chain operated12.4 CSC 铅封关Car seal close12.5 CSO 铅封开Car seal open12.6 LC 锁闭Lock closed12.7 LO 锁开Lock open12.8 NC 正常关Normally close12.9 NO 正常开Normally open12.10 ATM 大气压Atmosphere12.11 PN 公称压力Nominal pressure12.12 A 绝压12.13 G 表压12.14 (T) 温度Temperature12.15 (P) 压力Pressure13 施工编号缩写中文名称英文名称13.1 W 焊接Welding13.1.1 AW 电弧焊Arc welding13.1.2 GSAW 气体保护电弧焊Gas shielded-acr welding13.1.3 EFW 电熔焊Elecric fusion welding13.1.4 ERW 电阻焊Electric Resistance welding13.1.5 GW 气焊Gas welding13.1.6 LW 搭接焊Lap welding13.1.7 BW 对焊Butt welding13.4.8 TW 定位焊Tack welding13.1.9 SW 承插焊Socket welding13.1.10 CW 连续焊Continuous welding13.1.11 SEW 密封焊Seal welding13.1.12 SFG 堆焊Surfacing13.1.13 FW 现场焊接Field welding13.2 HT 热处理Heat treatment13.2.1 PH 预热Preheating13.2.2 SR 应力消除Stress relief13.2.3 PWHT 焊后热处理Post weld heat treatment13.3 EIT 检查、探伤和实验Examination, inspection & testing13.3.1 VE 外观检查Visual examination13.3.2 UI (UT) 超声探伤Ultrasonic inspection (test)13.3.3 RI (RT) 射线探伤Radiographic inspection (test)13.3.4 MPI (MT) 磁粉探伤Magnetic particle inspection (test) 13.3.5 LPI (PT) 液体渗透检验Liquid penterant inspection (test) 13.3.6 HADT 硬度实验Hardness testing13.3.7 HYDT 水压实验Hydraulic testing13.3.8 PNET 气压实验Pneumatic testing13.3.9 CE 焊条Covered electrode13.3.10 WW 焊丝Welding wire13.3.11 ASSY 装配、组合Assembly13.3.12 F 现场Field13.3.13 F/F 现场制造Field faricated13.3.14 SF 现场决定Suit in field13.3.15 CSP 冷紧Cold spring13.3.16 BCT 螺栓冷紧Bolt cold tightening13.3.17 BHY 螺栓热紧Bolt hot tightening13.3.18 CO 清洗口Clean out13.3.19 ANNY 退火Annealed13.4 PE 平端面Plain end13.5 BE 坡口端Belelled end13.6 THR 螺纹Thread13.7 HB 布氏硬度Brinnel hardness13.8 RC 洛氏硬度14 其他编号缩写中文名称英文名称14.1 FDN 基础Foundation14.2 INF 信息（资料）Information14.3 REF 参考Reference14.4 REV 修改Revision14.5 SEQ 序号（顺序）Sequence14.6 W/E 设备带来With equipment14.7 W/I 仪表带来With instrument14.8 CM 色标Colour mark14.9 CA 腐蚀裕度Corrosion allowance14.10 UTL 公用系统Utility14.11 UC 公用工程接头Utility connection14.12 QTY 数量Quantity14.13 WT 重量Weight14.14 MHR 工时Man hour14.15 BC 螺栓分布圆Bolt circle14.16 HP 高点High point14.17 LP 低点Low point14.18 SUC 吸入（口）Suction14.19 DIS 排出（口）Discharge14.20 SO 蒸气吹扫（口）Steam out14.21 NPT 美国标准锥管螺纹National standard taper pipe thread 14.22 NPS 美国标准直管螺纹National standard straight pipe thread 14.23 DR 排液Drain14.24 VT 放气Vent14.25 RTG （压力）等级Rating14.26 CL 等级Class14.27 SMLS 无缝Seamless14.28 螺旋缝。

配管工程常用词缩写

配管工程常用词缩写石油化工企业配管工程常用词缩写1 管子及管件中文名称管子弯头长半径弯头短半径弯头斜接弯头(虾米腰弯头) 异径弯头三通斜三通异径三通异径管接头(大小头) 同心异径管接头(同心大小头) 偏心异径管接头(偏心大小头) 管箍双头管箍单头管箍异径管箍内外螺纹接头活接头英文名称pipe elbow long radius elbow short radius elbow milre elbow reducing elbow tee lateral tee reducing tee reducer concentric reducer eccentric reducer coupling full coupling half coupling reducing coupling bushing union 缩写p el ell els mel rel t lt rt r cr er cpl fcpl hcpl rcpl bu un 中文名称快速接头翻边短节加强管接头螺纹加强管接头焊接加强管接头承插焊加强管接头弯头加强管接头斜接加强管接头鞍型加强管接头螺纹短节双头螺纹短节单头螺纹短节型锻螺纹短节管帽(封头) 焊接管帽螺纹管帽承插焊管帽椭圆形封头(管帽) 管堵(丝堵) 盲板8字盲板中文名称法兰密封面平面凸台面(光滑面) 凹凸面凹面凸面环连接面透镜面榫槽面英文名称quick joint stub end o-let threadolet weldolet socket weldolet elbolet latrolet sweepolet nipple threaded both end nipple threaded one end nipple swaged threaded nipple cap welded cap thread cap socket welded cap ellipsoid cap plug blank spectacle blind (blank) 英文名称flange sealing face flat face raised face male and female face female face male face ring jcin face lens facetongue and grcove face 缩写qj se ol tol wol swcl elol lol sol nip fnip hnip snip cp wc tc swc ec pg blk sb 缩写fsf ff rf mff fmf mf rjf lf tgf2 法兰中文名称法兰对焊法兰平焊法兰承插焊法兰螺纹法兰松套法兰大小法兰特殊法兰法兰盖(盲法兰)英文名称flange welding meck flange slip-on flange socket-wclding flange threaded flange lapped joint flange reducing flange special flange blind flange缩写flg wnf sof swf tf ljf redf spf bf3 垫片中文名称垫片非金属垫片石棉垫片橡胶垫片缠绕式垫片金属垫片金属平垫片齿形金属垫片4 紧固件中文名称螺栓双头螺柱螺母5 阀门中文名称闸阀截止阀止回阀蝶阀球阀6 管道上用的设备中文名称气液分离器阻火器固定过滤器Y型过滤器T型过滤器临时过滤器消声器视镜英文名称gasket non-metallic gasket asbestos gasket rubber gasket spiral wound gasket metallic gasket flat metallic gasket solid metal scrrated gasket 英文名称bolt stud bolt nut 英文名称gate valve globe valve check valve butterfly valve ball valve 英文名称separator flame arrester permanent strainer y-type strainer t-type strainer temporary strainer silencer sight flow indicator缩写g nmg ag rg smg mg fmg smsg 缩写b sb nu 缩写gv glv ghv buv bav 缩写spr fa psr sry srt tsr sil sfi中文名称聚四氟乙烯包半金属垫片金属包垫片透镜式金属环八角形金属环椭圆形金属环英文名称PTFE envelope semimetallic gasket meta-jacket gasket lens ring gasket octagonal ring gasket oval ring gasket缩写teg smg mjg ler ocr ovr中文名称花篮螺母垫圈弹簧垫圈中文名称旋塞阀调节阀安全阀减压阀蒸汽疏水阀中文名称取样冷却器排液漏斗管道混合器限流孔板混合孔板爆破片(爆破膜) 补偿器过滤器英文名称turnbuckle washer spring washer 英文名称plugvalve(ccck) control valve safcty calve pressure reducing valve steam trap 英文名称sample cooler drain funnel line mixer restriction orifice mixing orifice rupture disk expansion joint strainer缩写tb wsr swsr 缩写pv cv sv prv st 缩写sc df lm ro mo rd ej7 隔热、伴热中文名称隔热保温保冷防烫伤隔热伴热和保温管道伴热8 配管材料和等级中文名称金属材料碳钢铸钢锻钢镀锌钢渗铝钢黄铜青铜紫铜壁厚9 装置布置中文名称建北东西南北水平竖直、铅直、直立地坪10 图表中文名称工艺流程图管道和仪表流程图接续图详图英文名称缩写thermal insulation ins hot insulation hi cold insulation ci personnel protection insulationppi tracing and insulation tI piping tracing pt 英文名称metallic material carbon steel cast steel forged steel galvanized steel aluminum-impregnated steel brass bronze copper thickness 英文名称construction north east west south north horizontalvertical ground 英文名称process flow diagram piping instrument diagram continucd on drawing detail 缩写m cs cas fs gs als 中文名称蒸汽外伴热蒸汽内伴热蒸汽夹套伴热电伴热伴热管英文名称external steam tracing internal steam tracing steam-jacket tracing electric tracing tracing piping缩写est ist sjt et trp中文名称合金钢不锈钢奥氏体不锈钢铸铁可锻铸铁铝表号标准加强特强中文名称地下装置边界线事故淋浴洗眼器软管站接续分界线管道支架(管架)英文名称alloy steel stainless steel austenitic stainlesssteel cast iron mallcable iron aluminum schedule number standard extra strong double extra strong 英文名称underground battery limit line emergency shower eye hose station match line piping support缩写alys ss ass ci mi al sch std xs __s 缩写jg bl eses hs ml ps缩写cn e w s n h v grd 缩写pfd pid cod dtl中文名称管段图图号所在图号材料表英文名称spool drawing drawing number drawing identification list of material缩写spdwg dwgno dwgl lom11 尺寸标注中文名称标高管底管中心管顶底平顶平中心线切线对称的支架底支架顶净距(净空) 中心至中心中心至面12 操作方式及工作参数中文名称自动手控链条操作铅封关门铅封开闭锁13 施工中文名称焊接电弧焊气体保护电弧焊电熔焊电阻焊气焊搭接焊对焊定位焊承插焊英文名称elevation bottom of pipe center of pipe top of pipe flat on bottom flat on top center line tangent line symmetrical bottom of support top of support clearance center to center center to face 英文名称automatic manual control chain operated car seal close car seal open lock closed 英文名称welding arc welding gas shielded-arc welding electric fusion welding electric resistance welding gas welding lap welding butt welding tack welding socket welding缩写el bop cop top fob fot cl tl sym bos tos cl ctc ctf 缩写aut mc chop csc cso lc 缩写w aw gsaw efw erw gw lw bw tw sw中文名称中心至端部端到端法兰端面面到面直径公称直径内径外径尺寸最大最小平均约，近似英文名称center to end end to end flange and face face to face diameter nominal diameter inside diameter outnide diameter dimension maximum minimum average appoximate缩写cte ete fef ftf d dn id od dim max min avg app中文名称锁开正常关正常开大气压公称压力英文名称lock open normally close normally open atmosphere nominal pressure缩写lo nc no atm np中文名称外观检查超声探伤射线探伤磁粉探伤液体渗透检验硬度试验水压试验气压试验焊条焊丝英文名称visual examination ultrasonic inspection radiographic inspection magnetic particle inspection liquid penetrant inspection hardness testing hydraulic testing pneumatic testing covered electrode welding wire缩写ve ui ri mpi lpi hadt hydt pnet ce ww连续焊密封焊堆焊工地焊接热处理预热应力消除焊后热处理检查、探伤和试验14 其他中文名称基础信息(资料) 参考修改序号(顺序) 设备带来仪表带来色标腐蚀裕度公用系统数量重量continuous welding cw seal welding sew surfacing sfg field welding fw heat treatment ht preheating ph stress relief sr post weld heat treatment pwht examination inspection testing eit 英文名称foundation information reference revision sequence with equipment with instrument colour mark corrosion allowance utility quantity weight 缩写fdn inf ref rev seq w/e w/I cm ca utl qty wt装配、组合现场现场制造现场决定冷紧螺栓冷紧螺栓热紧清洗assembly field field fabricated suit in field cold spring bolt cold tightening bolt hot tightening clean outasy f f/f sf csp pct bht co中文名称工时螺栓分布圆加强的低点吸入排出蒸汽吹扫美国标准锥管螺纹美国标准直管螺纹英文名称缩写man hour mhr bolt circle bc reinforced rf low point lp suction suc discharge dis steam out so national standard taperpipe thread npt national standard straight pipe thread nps。

管道工程英文术语缩写

管道工程英文术语缩写管道工程英文术语缩写标准化文件发布号：（9312-EUATWW-MWUB-WUNN-INNUL-DDQTY-KII管道工程英文术语缩写（中英对照）1.管子及管件P 管子 PipeEL 弯头ELL 长半径弯头ELS 短半径弯头MEL 斜接弯头（虾米腰弯头）REL 异径弯头T 三通 TeeLT 斜三通RT 异径三通R 异径管接头（大小头） ReducerCR 同心异径管接头（同心大小头） Concentric reducerER 偏心异径管接头（偏心大小头） Eccentric reducerCPL 管箍 CouplingFCPL 双头管箍 Full couplingHCPL 单头管箍 Half couplingRCPL 异径管箍 Reducing couplingBU 内外螺纹接头 BushingUN 活接头 UnionHC 软管接头 Hose couplerSE 翻边短节 Stub endNIP 短节 Pipe nipple or straight nippleSNIP 异径短节 Swaged nippleCP 管帽（封头） CapPL 管堵（丝堵） PlugBLK 盲板 BlankSB 8字盲板 Spectacle blind (blank)RP 补强板 Reinforcing pad2.法兰 FLG 法兰 FlangeWNF 对焊法兰 Welding neck flangeSOF 平焊法兰 Slip-on flangeSWF 承插焊法兰 Socket-welding flangeT 螺纹法兰 Threaded flangeLJ 松套法兰 Lapped joint flangeREDF 异径法兰 Reducing flangeBF 法兰盖（日法兰） Blind flangeFSF 法兰密封面 Flange scaling FF 全平面 Flat face RF 凸台面Raised faceMFF 凹凸面 Male and female faceLF 凹面 Female faceLM 凸面 Male faceRJ 环连接面 Ring joint faceTG 榫槽面 T ongue and groove faceTF 榫面 T ongue faceGF 槽面 Groove face3.垫片 G 垫片 GasketNMG 非金属垫片 Non-metallic gasketAG 石棉垫片 Asbestos gasketRG 橡胶垫片 Rubber gasketTEG 聚四氟乙烯包复垫片 PTFE envelope gasket SMG 半金属垫片 Semimetallic gasketMJG 金属包垫片 Meta-jacket gasketSWG 缠绕式垫片 Spiral wound gasketMG 金属垫片 Metallic gasketFMG 金属平垫片 Flat metallic gasketSMSG 齿形金属垫片 Solid metal serrated gasket LER 透镜式金属环垫 Lens ring gasketOCR 八角形金属环垫 Octagonal ring gasketOVR 椭圆形金属环垫 Oval ring gaksetIR/OR 内外定位环 Inner ring and outer ringIR 内定位环 Inner ringOR 外定位环 Outer ring4.坚固件 B 螺栓 BoltSB 螺柱 Stud boltNU 螺母 NutTB 花蓝螺母 TurnbuckleWSR 垫圈 WasherSWSR 弹簧垫圈 Spring washer5.阀门 GV 闸阀 Gate valveGLV 截止阀 Globe valveCHV 止回阀 Check valveBUV 蝶阀 Butterfly valveBAV 球阀 Ball valvePV 旋塞阀 Plug valve (cock)CV 调节阀 Control valveSV 安全阀 Safety valveRV 减压阀 Pressure reducing valveST 蒸汽疏水阀 Steam trapPRV 泄压阀 Pressur relief valveBV 呼吸阀 Breather valveNV 针形阀 Needle valveAV 角阀DV 隔膜阀TWV 三通阀SGV 插板阀6.管道上用的小型设备SPR 气液分离器Separator FA 阻火器Flame arresterSR 过滤器 StrainerSRY Y型过滤器 Y-type strainerSRT T型过滤器 T-type strainerSRB 桶式过滤器 Bucket type strainerTSR 临时过滤器 Temporary strainerSIL 消声器 SilencerSG 视镜 Slight glassSC 取样冷却器 Sample coolerDF 排液漏斗 Drain funnelLM 管道混合器 Line mixerRO 限流孔板 Restriction orificeMO 混合孔板 Mixing orificeRD 爆破片（爆破膜） Rupture diskEJ 补偿器 Expansion joint7.隔热、伴热 INS 隔热 Thermal insulationH 保温 Hot insulationC 保冷 Cold insulationP 防烫伤隔热 Personnel protection insulationT&I 伴热 Tracing and insulationT 管道伴热（冷） TracingEST 蒸汽外伴热 External steam tracingIST 蒸汽内伴热 Internal steam tracingSJT 蒸汽夹套伴热 Steam-jacket tracingET 电伴热 Electric tracing8.配管材料和等级 M 金属材料 Metallic material CS 碳钢 Carbon steelCAS 铸钢 Cast steelFS 锻钢 Forged steelAS 合金钢 Alloy steelSS 不锈钢 Stainless steelAUSTSS 奥氏体不锈钢 Austenitic stainless-steelCI 铸铁 Cast ironMI 可锻铸铁 Malleable ironDI 球墨铸铁 Ductile ironAL 铝 AluminumBRS 黄铜 BrassBRZ 青铜 BronzeCU 紫铜 CopperLAS 低合金钢 Low alloy steelFLAS 低合金锻钢 Forged low alloy steelCLAS 低合金铸钢 Cast low alloy steelTHK 壁厚 ThicknessSCH 表号 Schedule numberSTD 标准 StandardXS 加强 Extra strongXXS 特强 Double extra strong9.装置布置 CN 建北 Construction northE 东 EastW 西 WestS 南 SouthN 北 NorthH 水平 HorizontalV 竖直、铅直、直立 VerticalGRD 地坪 GroundUG 地下 UndergroundBL 装置边界线 Battery limit lineESEW 事故沐浴洗眼器 Emergency shower and eye washer HS 软管站 Hose stationML 接续分界线 Match linePS 管道支架（管架） Piping support。

一般机电类通用缩略语（1）_机械英语词汇

a 安培（ampere，amps）abbr 缩写（abbreviation）ac 交流电流（alternating current）acb 空气无熔丝开关（air circuit breaker）adj 可调式（adjustable）afc 自动频率控制（automatic frequency control）ah 安培小时（ampere hour）al 铝（aluminum）am 安培表 / 调幅（ammeter / amplitude modulation）ampl 增幅器（amplifier）ann 警报器（announciator）ant 天线（antenna）app. 近似（approximate）as 安培计切换开关（ammeter switch）ats 自动切换开关（automatic transfer switch）aud 音频（audio）auto 自动（automatic）autotr 自动变压器（auto transformer）aux 辅助（auxiliary）avg 平均（average）af 框架容量（frame size）at 跳脱容量（trip rating）bat 电池（battery）batchg 电池充电机（battery charger）bcd 二进码十进制（binary coded decimal）bet 之间（between）bgm 背景音乐（back ground music）bil 基本绝缘水準（basic insulation level）bldg 建筑物（building）bot 底（层）（bottom）c 导线管（conduit）ca 电缆（cable）cab 配电箱（cabinet）cam 摄影机 / 空调辅助电表（camera, cooling auxiliary meter）cap 电容器/电容（capacitor/capacitance）cat 种类（category）cb 断路器（circuit breaker）ccc 中央控制中心（central control center）cctv 闭路电视（closed circuit television）ch 频道（channel）ckt 电路/迴路（circuit）clg 天花板（ceiling）clk 鐘（clock）cmc 母鐘（central master clock）cm 公分（centimeter）cdf 综合配线架（combined distribution frame）coax 同轴（coaxial）col 圆柱（column）comm 通讯（communication）conc 混凝土（concrete）cond 导线（conductor）conn 接头 / 连接（connector / connection）cons 控制台（control station）constr 施工（construction）cont 连续 / 继续（continue / continuation）cpt 控制电源变压器（control power transformer）cpu 中央处理（central processor unit）cr 控制电驛（control relay）crt 阴极射线管（cathode ray tube）cs 控制开关（control switch）csrc 中央监控（central supervisory and remote control）cmptr 电脑（computer）ct 比流器（current transformer）ctl 控制（control）ctr 中心（center）cu 铜（copper）cty 电缆架（cable tray）d/c 类位/类比转换器（digital to analog converter）da 分散放大器（distribution amplifier）db 分贝（decibel）dbm 毫瓦分贝（a db referred to one milliwatt）dc 直流（direct current）dd 数位类示（digital display）ddc 资料分配控制器（data distribution controller）ddt 资料显示终端机（data display terminal）dept 部门（department）det 详细图（detail）df 需量因素（demand factor）dgp 资料收集处理机（data gathering processor）dgt 电信总局（directorate general of telecommunications）dia 直径（diameter）dig 图（diagram）diff 差别的（differential）dim 尺度（dimension）disc 分开 / 不接（disconnect）distr 分布 / 分配（distribution）div 参差因数（diversity factor）dm 需量表（demand meter）dn 向下（down）do 抽出（draw out）dp 双极（double pole）dpdt 双极双投（double pole double throw）dpst 双极单投（double pole single throw）ds 隔离开关（disconnect switch）dt 双投（double throw）dtg 防尘（dust tight）drg 图（drawing）e 紧急（emergency）ea 每一（each）ec 空导管（empty conduit）el 高程（elevation）elec 电机（electric）elv 电梯（elevator）em 能源管理（energy management）emi 电磁干扰（electromagnetic interference）ems 环境管理子系统（environmental management subsystem）emt 金属电导管（electrical metallic tubing）encl 箱体（enclosure）entr 入口（entrance）epr 乙烯丙烯橡胶（ethylene propylene rubber）eq 等化器（equalizer）eqpt 设备（equipment）esc 电扶梯（escalator）et 紧急电话 / 经过时间（emergency telephone / elapse time）exp.jt 伸缩缝（expansion joint）ext 外部（exterior）ex 交换机 / 交换线路（exchange / exchange line）f，fi 频率（frequency）fa 火灾报警机（fire alarm）ft 多功能电话（feature telephone）fas 火警系统（fire alarm system）fb 熔线座（fuse block）fbo 非本工程范围（furnished by others）fdn 基础（foundation）fdr 馈线（feeder）ff 粉刷完成面（finished floor）fl 层（floor）fld 场（field）flex 软性的（flexible）fls 火灾及安全辅助系统（fire and life safety subsystem）fluor 萤光灯（fluorescent）fm 频率表 / 调频（frequency meter / frequency modulation）fo 光学纤维（fiber optic）fs 防火（fire stop）fsk 移频按键 / 频移键（frequency shift key）fu 熔线（fuse）furn 提供（furnished）fut 未来（future）ga 标準 / 尺度（gauge）galv 镀锌（galvanized）gb 接地匯流排（ground bus）gen 发电机（generator）g.f. 接地故障保护（ground fault protection）grs 无线电指引系统（guide radio system）g,gnd 地面 / 接地 / 绿色（ground / green）。

化工管件英文缩写

管件常用英文词汇及缩写I

管件常用英文词汇及缩写I弯头joint弯头angle fittings; bent pipe; elbow; knee 弯头扳手bent-handle wrench; bent spanner 弯头车刀angular tool弯头持针钳curved needle holders弯头刀架knee tool弯头道钉brob弯头管swan neck弯头键gib head key弯头接合knee-joint弯头螺栓bolt with one end bent back弯头锁紧螺母elbow jam unt弯头套管elbow union弯头套筒扳手offset socket wrench弯头脱水器elbow separator弯头芯盒elbow core box活接活接loose joint活接地swinging earth活接结合articulated joint活接联接器joint coupling活接三通union tee活接头articulation; union swivel; union活接头螺母union nut活接头螺栓swing bolt活接头套管union thimble活接卸槽articulated chute (浇混凝土用的) 三通三通tee bend; tee branch; tee joint; tee conneetion; tee fitting; wye; Y; yoke 三通玻璃栓three-way glass stopcock 三通道放大器three-channel amplifier; three-path amplifier三通道自动驾驶仪three-dimensional autopilot三通电缆分线盒three-way coupling box三通阀tee valve; three-port valve; three-way valve; triple valve三通阀盖triple-valve cap三通阀活塞triple-valve piston三通阀联箱three way valve menifold三通阀体triple body; triple-valve body三通管single sweep tee; T-branch (pipe); three-limb tube三通管接头tee pipe coupling三通横长horizontal length of tee三通换向旋塞three-way reversing cock三通活栓three-way cock三通货协定triparties currency agreement三通接头tee coupling; tee fitting; tee union; three-way piece; three-way connection 三通接线夹three-way connector 三通开关three-way cock三通控制阀three-way control valve三通连接tee junction三通路循环器three-terminal circulator三通式热风炉three-pass stove三通天线转发开关triplexer三通筒triple cylinder三通筒垫密片triple-cylinder gasket三通弯头three-way elbow三通旋塞tee cock; three-way cock; three-throw tap三通循环器three-terminal circulator三通液体流量计tee fluid flow meter三通闸阀treble ported slide valve直通直通direct connection; straight in; straight bore; through; feed(-)through; once-through 直通拨号through dial(l)ing 直通测量线路end-to-end measurement直通单向阀in-line check valve; straight check valve; straightway check valve直通道路through road直通的through and through直通地dead earth; dead ground直通垫外底through midsole直通电报telex直通电报通信telex communication直通电流through current直通电流偏置through current bias直通电路direct circuit直通阀pass valve; straight-through valve; straightway valve; through valve 直通干馏炉through retort直通锅炉once-through boiler直通换料once-through refuelling直通回路straight circuit直通汇接呼叫制straight forwardjunction working直通监控through supervision直通接头straight coupling; straight fitting直通接线装置through joint直通街道through expressway; through street; throughway直通进位standing carry直通开关globe cock直通空气制动阀straight air brake valve直通空气制动器straight air brake直通快动阀straight-through fast acting valve直通连接straight-through joint直通裂化straight-through cracking直通流动straight through flowS型弯管“S” bend单侧偏置90o弯管Single offset “U”bendU型弯管“U” bend双偏置U型膨胀弯管Double offset expansio n “U” bend斜接弯头Mitre elbow斜接弯Mitre bend三节斜接管4-piece mitre bend折皱弯管Corrugated bend法兰法兰端Flanged end坡口端；对焊端Beveled end [BEV.E];Butt welded end平端Plain end [PE]承插焊端Socket welding end螺纹端Threaded end [TE]承口Bell end焊接端Welding end钢管法兰Steel pipe flange螺纹法兰Threaded flange滑套法兰（平焊法兰) Slip-on-welding flange Slip-on [SO] flange 承插焊法兰Socket welding flange松套法兰Lap joint flange [LJF]对焊法兰Weld neck flange [WNF]法兰盖Blind flange ; Blind孔板法兰Orifice flange异径法兰Reducimg flange盘座式法兰Pad type flange松套带颈法兰Loose hubbed flange板式平焊法兰Welding plate flange松套法兰Lap joint flange [LJF]对焊法兰Weld neck flange [WNF]法兰盖Blind flange ; Blind孔板法兰Orifice flange异径法兰Reducimg flange盘座式法兰Pad type flange松套带颈法兰Loose hubbed flange板式平焊法兰Welding plate flange对焊环（与stubend相似）Welding neck collar（与stubend 相似）平焊环Welding-on collar管端突缘Stub end翻边端Lapped pipe end松套板式法兰Loose plate flange压力级Pressure rating ; Pressure rating class压力-温度等级Pressure-temperature rating法兰密封面；法兰面Flange facing突面Raised face [RF]凸面Male face [MF]凹面Female face [FMF]榫面Tongue face槽面Groove face环连接面Ring joint face短半径弯头Short radius elbow长半径180o弯头Long radius return短半径180o弯头Short radius return带侧向口的弯头（右向或左向）Side outlet elbow(Right hand or left hand) 双支管弯头Double branch elbow三通Tee异径三通Reducing tee等径三通Straight tee带侧向口的三通（右向或左向）Side outlet tee (Right hand or left hand) 异径三通（分支口为异径）Reducing tee(Reducing on outlet)异径三通（一个直通口为异径）Reducing tee (Reducing on one run)堵头Plug短管Nipple异径短节Reducing nipple异径短节(外螺纹或无螺纹) Swage nippe (选自BS 3800)弯头Elbow异径弯头Reducimg elbow带支座弯头Base elbow长半径弯头Long radius elbow管子（按照标准规格制造的配管用管）Pipe管子（不按照标准规格制造的其他用管) Tube钢管Steel pipe铸铁管Cast iron pipe衬里管Lined pipe复合管Clad pipe碳钢管Carbon steel [C.S.]pipe合金钢管Alloy steel pipe不锈钢管Stainless steel [S.S.]pipe奥氏体不锈钢管Austenitic stainless pipe铁合金钢管Ferritic alloy steel pipe扎制钢管Wrought-steel pipe段铁管Wrought-iron pipe无缝钢管Seamless[SMLS]steel pipe焊接钢管Welded steel pipe电阻焊钢管Electric-resistance-welded steel pipe电熔（弧）焊钢板卷管Electric-fusion (arc)-welded steel-plate pipe 螺旋焊接钢管Spiral welded steel pipe镀锌钢管Galvanized steel pipe热轧无缝钢管Hot-rolling seamless pipe冷拉无缝钢管Cold-drawing seamless pipe水煤气钢管Water-gas steel pipe塑料管Plastic pipe玻璃管Glass tube橡胶管Rubber tube壁厚Wall thickness(WT)壁厚系列号Schcdule number架厚的，加强的Extra heavy; Extra stromg双倍加强的，双倍加厚的Double extra heavy; Double extra strong 预制弯管Fabricated pipe bend跨越弯管( )形Cross-over bend偏置弯管（）形Offset bend锥管螺纹密封焊连接Seal-welded taper pipe threaded joint承插焊连接（接头）Socket welded joint承插连接（接头）Bell and spigot joint焊接接头Welded joint环垫接头Ring joint[RJ]万向接头Universal软钎焊连接（接头）Soldered joint搭接接头Lapped joint外侧厚度切斜角Bevel for outside thickness内侧厚度切斜角Bevel for inside thickness内外侧厚度切斜角Bevel for combined thickness法兰式的Flanged [FLGD]对焊的Butt welded [BW]螺纹的Threaded [THD]承插焊的Socket welded [SW]小端为平的Small end plain [SEP]大端为平的Large end plain [LEP]两端平Both ends plain [BEP]小端带螺纹Small end thread [SET]大端带螺纹Large end thread一端带螺纹One end thread两端带螺纹Both ends thread整体管法兰Integral pipe flange光滑突面Smooth raised face [SRF]法兰面加工Facing finish粗糙度Roughness光滑的Smooth齿形的Serrated均方根Root mean square [RMS]算术平均粗糙高度Arithmetical average roughness height[AARH] HALF COUPLING 单承口管箍1.1 P 管子Pipe1.2.3 MEL 斜接弯头（虾米腰弯头）Mitre elbow1.2.4 REL 异径弯头Reducing elbow1.3 T 三通Tee1.3.1 LT 斜三通Lateral tee1.3.2 RT 异径三通Reducing tee1.4 R 异径管接头（大小头）Reducer1.4.1 CR 同心异径管接头（同心大小头）Concentric reducer 1.4.2 ER 偏心异径管接头（偏心大小头）Eccentric reducer1.5 CPL 管箍Coupling1.5.1 FCPL 双头管箍Full coupling1.5.2 HCPL 单头管箍Half coupling1.5.3 RCPL 异径管箍Reducing coupling1.6 BU 内外螺纹接头Bushing1.7 UN 活接头Union1.8 HC 软管接头Hose coupler1.9 SE 翻边短节Stub end1.10 NIP 短节Pipe nipple or straight nipple1.10.1 SNIP 异径短节Swaged nipple1.11 CP 管帽（封头）Cap1.12 PL 管堵（丝堵）Plug1.13 BLK 盲板Blank1.13.1 SB 8字盲板Spectacle blind (blank)1.14 RP 补强板Reinforcing padHARDNESS 硬度（最大值197）HEAT CONTROL NUMBER 热处理炉号HEAT TREATMENT（热处理），有缝部分填N，无缝部分填A HEX HEAD BUSHING 卜申HEX HEAD PLUG 六角塞头HEX NIPPLE 六角立布HIGH PRESSURE ELBOW 高压弯头HIGH PRESSURE REDUCER 高压异径管HIGH PRESSURE TEE 高压四通hydraulic hose液压软管HJ 环境保护行业标准hose clip软管卡子hose protector软管保护管hot-rolling seamless pipe热轧无缝钢管HR 热轧INNER DIAMETER （简）ID 内径INSERT 变径接头integral pipe flange整体管法兰JIS 日本工业标准jumper hose跨接软管jumper lose connection跨接软管连接器Lap Joint Flanges对焊环松套法兰lap joint flange (LJF) 松套法兰lapped joint搭接接头，松套连接lapped pipe end翻边端large end plain (LEP) 大端为平的1 管道组成件Piping component1.1 管子Pipe管子(按照配管标准规格制造的) pipe管子(不按配管标准规格制造的其他用管) tube钢管steel pipe铸铁管cast iron pipe衬里管lined pipe复合管clad pipe碳钢管carbon steel pipe合金钢管alloy steel pipe不锈钢stainless steel pipe奥氏体不锈钢管austenitic stainless steel pipe铁合金钢管ferritic alloy steel pipe轧制钢管wrought-steel pipe锻铁管wrought-iron pipe无缝钢管seamless (SMLS) steel pipe焊接钢管welded steel pipe电阻焊钢管electric-resistance welded steel pipe电熔（弧）焊钢板卷管electric-fusion (arc)-welded steel-plate pipe螺旋焊接钢管spiral welded steel pipe镀锌钢管galvanized steel pipe热轧无缝钢管hot-rolling seamless pipe冷拔无缝钢管cold-drawing seamless pipe水煤气钢管water-gas steel pipe塑料管plastic pipe玻璃管glass tube橡胶管rubber tube直管run pipe; straight pipe1.2 管件Fitting弯头elbow异径弯头reducing elbow带支座弯头base elbowk半径弯头long radius elbow短半径弯头short radius elbow长半径180°弯头long radius return短半径180°弯头short radius return带侧向口的弯头（右向或左向）side outlet elbow (right hand or left hand) 双支管弯头（形）double branch elbow三通tee异径三通reducing tee等径三通straight tee带侧向口的三通（右向或左向）side outlet tee (right hand or 1eft hand)异径三通（分支口为异径）reducing tee (reducing on outlet) 异径三通（一个直通口为异径）reducing tee (reducing on one run)带支座三通base tee异径三通（一个直通口及分支口为异径）reducing tee (reducing on one run and outlet) 异径三通（两个直通口为异径，双头式）reducing tee (reducing on both runs, bull he ad)45°斜三通45°lateral45°斜三通（支管为异径）45°lateral (reducing on branch)45°斜三通(一个直通口为异径) 45°lateral (reducing on o ne run) 45°斜三通(一个直通口及支管为异径) 45°lateral (reducing on one run and branch)Y型三通（俗称裤衩）true “Y”四通cross等径四通straight cross异径四通reducing cross异径四通（一个分支口为异径）reducing cross (reducing on one outlet)异径四通（一个直通口及分支口为异径）reducing cross (reducing on one run and out let)异径四通（两个分支口为异径）reducing cross (reducing on both outlet)异径四通（一个直通口及两个分支口为异径）reducing cross (reducing on one run an d both outlet)异径管reducer同心异径管concentric reducer两端带螺纹both end thread (BET)一端带螺纹one end thread (OET)支管连接branch connection焊接支管branch pipe welded directly to the run pipe法兰端flanged end坡口端beveled end (BE)对焊端butt welded end平端plain end (PE)承插焊端socket welding end螺纹端threaded end (TE)承口bell end焊接端welding end法兰连接（接头）flanged joint对焊连接（接头）butt welded joint螺纹连接，管螺纹连接threaded joint, pipe threaded joint 锥管螺纹密封焊连接seal-welded taper pipe threaded joint 承插焊连接（接头）socket welded joint承插连接（接头）bell and spigot joint环垫接头ring joint (RJ)万向接头universal joint软钎焊连接（接头）soldered joint搭接接头，松套连接lapped joint外侧厚度切斜角bevel for outside thickncss内侧厚度切斜角bevel for inside thickness内外侧厚度切斜角bevel for combined thickness法兰式的flanged (FLGD)对焊的butt welded (BW)螺纹的threaded (THD)承插焊的socket welded (SW)小端为平的small end plain (SEP)大端为平的large end plain (LEP)两端平both ends plain (BEP)小端带螺纹small end thread (SET)大端带螺纹large end thread (LET)多波multiple bellow压力平衡式膨胀节pressure balanced expansion带铰链膨胀节hinged expansion joint轴向位移型膨胀节axial movement type expansion joint 自均衡膨胀节（外加强环）self-equalizing expansion joint 带接杆膨胀节tied expansion joint万向型膨胀节universal type expansion joint球形补偿器ball type expansion joint填函式补偿器slip type (packed type) expansion joint 单向滑动填料函补偿器single actionpacked slip joint 1.7.2 管道特殊元件Piping Special Element软管接头hose connection (HC)快速接头quick coupling金属软管metal hose橡胶管rubber hose挠性管flexible tube鞍形补强板reinforcing saddles补强板reinforcement pad特殊法兰special flange漏斗funnel排液环drip ring排液漏斗drain funnel插板blank垫环spacer8字盲板spectacle blind; figure 8 blind限流孔板restriction orifice爆破片rupture disk法兰盖贴面protective disc费托立克接头victaulic coupling1.8 端部连接End Connection（水）龙头bibb; bib; faucet抽出液阀（小阀）bleed valve旁路阀by-pass valve软管阀hose valve混合阀mixing valve破真空阀vacuum breaker冲洗阀flush valve第一道阀；根部阀primary valve根部阀root valve总管阀header valve事故切断阀emergency valve1.7 管道特殊件Piping Specialty1.7.1 管道特殊件（组件）粗滤器strainer过滤器filter临时粗滤器（锥型）temporary strainer (cone type)y 型粗滤器y-type strainerT型粗滤器T-type strainer永久过滤器permanent filter丝网粗滤器gauze strainer洗眼器及淋浴器eye washer and shower视镜sight glass阻火器flame arrester喷嘴；喷头spray nozzle取样冷却器sample cooler消声器silencer膨胀节expansion joint波纹膨胀节bellow expansion joint单波single bellow双波double bellow杠杆重锤式lever and weight type引导阀操纵的安全泄气阀pilot operated safety valve复式安全泄气阀twin type safety valve罐底排污阀flush-bottom tank valve电磁阀solenoid valve, solenoid operated valve电动阀electrically operated valve, electric-motor operated valve 气动阀pneumatic operated valve低温用阀cryogenic service valve蒸汽疏水阀steam trap机械式疏水阎mechanical trap浮桶式疏水阀open bucket trap, open top bucket trap浮球式疏水阀float trap倒吊桶式疏水阀inverted bucket trap自由浮球式疏水阀loose float trap恒温式疏水阀thermostatic trap金属膨胀式蒸汽疏水阀metal expansion steam trap液体膨胀式蒸汽疏水阀liquid expansion steam trap双金属膨胀式蒸汽疏水阀bimetallic expansion steam trap压力平衡式恒温疏水阀balanced pressure thermostatic trap热动力式疏水阀thermodynamic trap脉冲式蒸汽疏水阀impulse steam trap放气阀（自动放气阀）air vent valve (automatic air vent valve) （疏水阀用）平板式滑动闸阀slab type sliding gate valve 盖阀flat valve换向阀diverting valve, reversing valve热膨胀阀thermo expansion valve自动关闭阀self-closing gate valve自动排液阀self-draining valve管道盲板阀line-blind valve挤压阀squeeze valve（用于泥浆及粉尘等）偏心阀板蝶阀offset disc burerfly valve; eccentric butterfly valve斜阀盘蝶阀canted disc butterfly valve连杆式蝶阀link butterfly valve8) 柱塞阀piston type valve(9) 旋塞阀plug valve三通旋塞阀three-way plug valve四通旋塞阀four-way plug valve旋塞cock衬套旋塞sleeve cock(10) 隔膜阀diaphragm valve橡胶衬里隔膜阀rubber lined diaphragm valve直通式隔膜阀straight way diaphragm valve堰式隔膜阀weir diaphragm valve(11) 夹紧式胶管阀pinch valve（用于泥浆、粉尘等）(12) 止回阀check valve升降式止回阀lift check valve旋启式止回阀swing check valve, flap check valve 落球式止回阀ball check valve弹簧球式止回阀spring ball check valve双板对夹式止回阀dual plate wafer type check valve 无撞击声止回阀non-slam cheek valve底阀foot valve切断式止回阀stop check valve; non-return valve活塞式止回阀piston check valve斜翻盘止回阀tilting disc check valve蝶式止回阀butterfly check valve1.6.3 其它用途的阀安全泄气阀safety valve (SV)安全泄液阀relief valve (RV)安全泄压阀safety relief valve升杆式（明杆）rising stem (RS)非升杆式（暗杆）non-rising stem (NRS)指示器/限位器indicator/stopper注油器grease injector可更换的阀座环renewable seat ring1.6.2 常用阀(1）闸阀gate valve平行双闸板double disc parallel seat开口楔形闸板split wedge挠性整体楔形闸扳flexible solid wedge整体楔形闸板solid wedge塞型闸阀plug gate valve直通型闸阀through conduit gate valve(2) 截止阀globe valve球心型阀盘globe type disc塞型阀盘plug type disc可转动的阀盘swivel disc(3) 节流闪阀throttle valve针阀needle valve(4) 角阀angle valve(5) Y型阀（Y 型阀体截止阀）Y-valve (Y-body globe valve)(6) 球阀ball valve三通球阀3-way ball valve装有底轴的trunnion mounted耐火型fire safe type浮动球型floating ball type防脱出阀杆blowout proof stem(7) 蝶阀butterfly valve对夹式（薄片型）wafer type凸耳式lug type螺栓连接的阀盖bolted bonnet (BB)活接阀盖（帽）union bonnet (cap)螺栓连接的阀帽bolted cap (BC)焊接阀盖welded bonnet (WB)本体阀杆密封body stem seal石棉安全密封asbestos emenen seal倒密封back seal压力密封的阀盖pressure-tight bonnet动力操纵器powered operator电动操纵器electric motor operator气动操纵器pneumatic operator液压操纵器hydraulic operator快速操纵器quick-acting operator滑动阀杆sliding stem正齿轮传动spur gear operated伞齿轮传动bevel gear operated扳手操作wrench operated链轮chain wheel手轮hand wheel手柄hand lever (handle)气缸（或液压缸）操纵的cylinder operated链条操纵的chain operated等径孔道full bore; full port异径孔道reducing bore, reduced port,venturi port 短型short pattern紧凑型（小型）compact type笼式环lantern ring压盖gland阀杆填料stem packing阀盖垫片bonnet gasket斜接弯管mitre bend三节斜接弯管3-piece mitre bend折皱弯管corrugated bend圆度roundness1.4 法兰Flange (FLG）整体管法兰integral pipe flange钢管法兰steel pipe flange螺纹法兰threaded flange滑套法兰（包括平焊法兰）slip-on flange (SO); slip-on wel ding flange承插焊法兰socket welding flange松套法兰lap joint flange (LJF)对焊法兰welding neckflange (WNF)法兰盖blind flange, blind孔板法兰orifice flange异径法兰reducing flange盘座式法兰pad type flange松套带颈法兰loose hubbed flange焊接板式法兰welding plate flange对焊环welding neck collar （与stub end相似）平焊环welding-on collar突缘短节stub end, lap翻边端lapped pipe end松套板式法兰loose plate flange压力级pressure rating, pressure rating class压力—温度等级pressure-temperature rating法兰密封面，法兰面flange facing突面raised face (RF)凸面male face (MF)凹面female face (FMF)榫面tongue face。

1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。