低压配电柜检验报告单

合集下载

电气防火安全检测报告

电气防火安全检测报告
注：符合要求指的是符合检测依据中所列标准有关要求，反之为不符合，不涉及项目的填/。

（消防电源及配电）
（变电所）
（变电所）
（变压器）
（互感器）
（补偿电容器）
（低压配电、电气控制柜（箱、板））
（低压配电、电气控制柜（箱、板））
（低压配电线路）
（低压配电线路）
（低压配电线路）
（低压配电线路）
（低压配电线路）
电气防火安全检测报告
电气防火安全检测报告
（稳压、整流设备）
（照明装置）
（照明装置）
电气防火安全检测报告（照明装置）
（插座与开关）
（插座与开关）
（接地与等电位连接）
（接地与等电位连接）
（接地与等电位连接）
（接地与等电位连接）
表1 交流高压电器触头及导体连接端子
表7 高温或腐蚀性场所,。

交流低压开关柜GGD例行检验报告

XXX电气有限公司
交流低压开关柜GGD例行检验报告
No：
产品名称：交流低压开关柜
型号规格：GGD-1000
依据标准：GB/T 7251.12-2013
出厂编号：2020101021
地下室低压配电柜
生产日期：2020年10月10日
序
项目
技术要求
实测
试验结果
1
一般检查
柜体各功能单元门的开启角应大于90°，转动灵活
符合
对主电路和不与主电路直接连接的辅助电路之间、辅助电路与框架之间应能受50Hz，1890V历时7s耐压试验。
符合
9
保护措施和保护电路的连续性
有主接地点和接地标记，零部件和电器元件的保护接地使用专用的螺钉，以保证保护电路的连续性。
符合
电阻值应在100mΩ以下。
主开关安装支架-主接地
≤50MΩ
分支开关安装支架-主接地
≤50MΩ
接线端子支架-主接地
≤50MΩ
门锁-主接地
≤50MΩ
10
操作试验
手动操作试验：装置中所有手动操作部分：如主开关的操作手柄等手动操作5次而无异常现象出现。有连锁功能要求的应连锁可靠。
符合
11
一致性检查
1关键元器件和材料、2.结构 3.铭牌应与型式试验报告描述一致
符合
12
检验结论：该产品经我公司检验合格，准予出厂
符合
5
内部电路和连接
装应符合认证产品的一致性要求、工艺要求和图纸规定的要求。
符合
6
外接端子
数量、类型和标识应符合成套设备输出接线的要求及型式试验报告的要求
符合
7
绝缘电阻
相与相之间,相与地之间的绝缘电阻值绝缘电阻不应小于1000Ω/V，规定≥10MΩ。

低压配电柜检验报告

低压配电柜检验报告低压配电柜是一种用于电力系统的主要电气设备，用于将电能从输电线路引入建筑物内，然后将电能分配给各个电气设备和电气系统。

低压配电柜的正常运行对于保障电力供应的质量和安全至关重要。

为了确保低压配电柜的正常运行，需要进行定期的检验和维护。

以下是对低压配电柜进行检验的报告。

一、检验项目1.外观检查：检查低压配电柜外壳和机构的完整性和无损情况，确保没有明显的变形、腐蚀和损坏。

2.电气性能检查：使用合适的电器仪器，对低压配电柜的电气参数进行测量，包括电压、电流和功率因数等。

3.保护装置检查：测试保护装置的动作性能，包括短路保护、过载保护和漏电保护等。

确保保护装置正常工作。

4.连接器和接线端子检查：检查连接器和接线端子的紧固情况，并进行测量，确保连接器和接线端子正常工作。

5.抗抖振和抗冲击性能检查：通过模拟低压配电柜在运行过程中受到的震动和冲击，检验低压配电柜的机械强度和固定性能。

6.温升试验：通过对低压配电柜进行负载试验，测量低压配电柜运行过程中的温升情况，确保低压配电柜正常工作时不会出现过高的温度。

二、检验结果经过以上检验项目的详细检查和测试，得出以下结果：1.低压配电柜的外观完整，无明显的变形、腐蚀和损坏。

2.低压配电柜的电气参数在正常范围内，符合设计要求。

3.保护装置的动作性能良好，能够及时保护电气设备和人身安全。

4.连接器和接线端子紧固可靠，无松动现象，电气连接正常。

5.低压配电柜具有较好的抗抖振和抗冲击性能，能够稳定运行在振动和冲击环境下。

6.温升试验结果显示低压配电柜在正常工作时，温度适中，无过高温度现象。

三、结论根据以上检验结果，可以得出以下结论：1.低压配电柜外观完好，机械强度良好，能够保护内部的电气设备。

2.低压配电柜的电气参数在正常范围内，可以正常供电给各个电气设备。

3.低压配电柜的保护装置具有良好的动作性能，能够及时保护电气设备和人身安全。

4.连接器和接线端子紧固可靠，电气连接正常，避免了电气接触不良的情况。

低压配电柜检验报告单

低压配电柜检验报告单
有一定的专业知识以及分析，图表等
一、检验报告概述
本文的主要目的是检验低压配电柜的安全性。

在本次检验中，首先将对外部整体外观尺寸和内部元件等状况进行检查，以确保设备外观完整无损，并确保设备内部元件正常工作。

其次，将开展检验，检查低压配电柜的电气安全性以及电器安装施工质量。

二、检验工作
2.1外部整体外观
（1）外观尺寸检查：首先，针对低压配电柜的外观尺寸进行检查，以确保外观尺寸与图纸规定尺寸一致，检查柜体及框架的外观形状是否完整，检查柜门及连接件的尺寸是否吻合，以及其表面处理是否达到要求。

（2）内部元件检查：检查低压配电柜内部的元件，确保每个元件的安装质量及工作状态达到要求，确保每个元件的接线无误，确保电表的标定是否正确，确保内部连接端子处的接触是否良好，确保关键元件的安装是否牢固，以及关键元件的易耗部件是否有效。

2.2低压配电柜电气安全性检验
（1）绝缘电阻检验：首先，通过绝缘电阻检验仪，检查低压配电柜的各端子和金属外壳的绝缘电阻，以确保设备的电气安全性，以及内部电路的完整性。

低压配电柜检验报告单

低压配电柜检验报告单一、基本信息：检验单位：检验日期：被检单位：检验周期：二、检验项目：1.设备安装情况：（1）检查配电柜的基础安装情况，包括支架、固定螺栓的锁紧情况以及相邻设备之间的间距是否符合要求；（2）检查配电柜的接地是否符合要求，并进行接地电阻测量；（3）检查配电柜内的设备的安装是否牢固，连接是否正常，线缆是否整齐；（4）检查配电柜的门锁是否正常，门是否能够完全关闭，并确认门的密封性；（5）检查配电柜的外观是否有划痕、破损等问题。

2.设备性能测试：（1）确认被检配电柜的额定操作电流和额定操作电压；（2）进行配电柜的绝缘电阻测试，确保绝缘电阻符合标准要求；（3）进行配电柜的接地电阻测试，确保接地电阻符合标准要求；（4）进行配电柜的漏电流检测，确保漏电流符合标准要求；（5）进行配电柜的开关操作测试，确认开关的正常使用；（6）进行配电柜的负荷开关切换能力测试，确保能正常切换负荷；（7）进行配电柜的温升试验，确认设备在正常工作负荷下的温升符合标准要求。

三、检验结果：1.设备安装情况：正常/异常（异常情况详述）。

2.设备性能测试：（1）绝缘电阻：符合/不符合（具体数值）。

（2）接地电阻：符合/不符合（具体数值）。

（3）漏电流：符合/不符合（具体数值）。

（4）开关操作：正常/异常。

（5）负荷开关切换能力：正常/异常（具体情况）。

（6）温升试验：符合/不符合（具体数值）。

四、检验结论：根据以上检验结果，本次低压配电柜的安装和性能检测结果为（合格/不合格），具体情况如下：（对不合格情况进行详细说明，并提出相应的解决方案和改进措施）五、下一步措施：根据本次检验结果，建议被检单位采取以下措施：（1）对于存在的安装问题，及时修复并重新安装，确保设备安装牢固；（2）对于存在的性能问题，根据不同情况采取相应的解决方案，确保设备能够正常运行；（3）定期对配电柜进行维护和检修，确保设备的安全可靠性。

六、检验人员签名：。

低压配电柜产品出厂检验报告

低压配电柜产品出厂检验报告一、检验概述本报告是对低压配电柜产品进行出厂检验的结论性报告，旨在验证产品的性能和质量是否符合相关标准和客户要求。

本次出厂检验采用了标准化的测试方法和设备，确保结果的准确性和可靠性。

二、检验项目1.外观检验：对产品的外观进行全面检查，包括外壳是否完整、标识是否清晰、面板是否平整等。

2.功能检验：对产品的各项功能进行测试，包括开关操作是否正常、电流是否在规定范围内、短路和过载保护是否可靠等。

3.绝缘电阻检验：对产品的绝缘电阻进行测量，确保产品的绝缘性能符合要求。

4.效应应力测试：对产品进行效应应力测试，模拟产品在正常使用过程中的负荷情况，确保产品的结构和材料能够承受正常工作状态下的应力。

5.耐压试验：对产品进行耐压试验，模拟产品在特殊环境下的工作情况，例如高温、低温和高湿度等，确保产品能够在各种环境下正常工作。

6.电气参数测量：对产品的电气参数进行测量，例如电压、电流、功率因数等，确保产品符合设计要求。

7.电弧灭弧性能测定：对产品的电弧灭弧性能进行测试，确保产品在发生电弧事故时能够迅速灭弧，以保护人员和设备的安全。

三、检验结果经过上述项目的检验，本次低压配电柜产品出厂检验的结果如下：1.外观检验：产品的外观完整，标识清晰，面板平整。

2.功能检验：产品的开关操作正常，电流在规定范围内，短路和过载保护可靠。

3.绝缘电阻检验：产品的绝缘电阻符合要求。

4.效应应力测试：产品在效应应力测试中表现良好，未出现结构破损或材料变形等情况。

5.耐压试验：产品在耐压试验中正常工作，无异常情况发生。

6.电气参数测量：产品的电气参数符合设计要求。

7.电弧灭弧性能测定：产品的电弧灭弧性能达到或超过标准规定，对电弧能够迅速灭弧。

综上所述，本次低压配电柜产品出厂检验的结果符合相关标准和客户要求，产品在各项指标上均符合设计要求，质量可靠、性能稳定。

四、结论1.本次低压配电柜产品出厂检验的结果显示，产品在外观、功能、绝缘性能、结构强度、耐压能力、电气参数和电弧灭弧性能等方面都符合要求。

低压开关柜合格检验报告

低压开关柜合格检验报告
自查报告。

日期，2022年10月15日。

自查人，XXX公司电气部门。

自查项目，低压开关柜合格检验。

自查内容：
1. 外观检查，检查开关柜外壳、门板、连接件等是否完好，无损坏、变形等情况。

2. 内部元件检查，检查开关柜内部元件如断路器、接触器、电缆等是否安装正确，无松动、破损等情况。

3. 接地检查，检查开关柜的接地装置是否牢固可靠，接地电阻是否符合要求。

4. 绝缘检查，使用绝缘电阻测试仪对开关柜的绝缘电阻进行检测，确保符合标准要求。

5. 功能检查，对开关柜进行通电测试，检查各个元件的工作是否正常，无异常声响、发热等情况。

自查结果：
经过自查，我们发现开关柜外观完好，内部元件安装正确，接地装置牢固可靠，绝缘电阻符合要求，功能正常。

未发现任何安全隐患和质量问题。

自查结论：
本次低压开关柜合格检验自查结果合格，符合相关标准要求。

我们将继续加强对电气设备的日常检查和维护，确保设备运行安全可靠。

自查人签名：日期：
XXX公司电气部门主管签名：日期：。

低压试验报告

e.额定频率（）f.额定工作电压（）
合格
11
清洁检查
装置内应无灰尘、铁屑、线头等杂物。
合格
二、机械操作与功能单元互换性检查
序号
检验项目
技术要求
检验结果
1
机械操作
所有手动部件都应操作五次，机构应灵活可靠，无异常现象出现，机械联锁应正确可靠。
合格
2
功能单元互换检查
用不同规格的任一功能单元在同一规格的两个功能单元隔室中各抽插五次，应灵活无卡滞。
耐压值（KV）
应无击穿和放电现象
合格
1
主电路：A+B+C+N—地
2.5KV无击穿和放电现象
^格
2
A—B
2.5KV无击穿和放电现象
^格
3
B—C
2.5KV无击穿和放电现象
^格
4
C—A
2.5KV无击穿和放电现象
^格
5
A+B+C—地
2.5KV无击穿和放电现象
^格
6
主电路与它不直接相连的辅助电路之间
2.5KV无击穿和放电现象
3.不应贴近裸露带电部件或带尖角的边缘敷设，应使用线夹固定在骨架或
合格
7
支架上，最好敷设在线槽内。
导线
4.穿过钢制金属隔板的导线穿线孔要加护套。
合格
安装
5.在可移动的地方要采用套管加以保护，并留有一定裕量。
合格
6.通常一个端子只连接一根导线，必要时允许连接两根导线，当需要连接
合格
两根或两根以上的导线时，应采取措施以确保连接可靠。
产品出厂试验报告
用户单位：
项目名称：
产品名称：交流低压配电柜

GGD配电柜出厂检验报告

GGD型交流低压配电控制柜出厂检验报告型号：___________________一、目的通过检查和试验，对GGD型交流低压配电柜在技术条件，范围的性能、安全性、适应性及制造、安装工艺进行验证，使产品达到出厂要求。

二、主要依据1、LEC439-1-1992低压成套开关设备第一部分2、GB7251-1-1997低压成套开关设备和控制条一部分三、试验项目1、柜体检验2、装配检验3、断路器检验4、隔离刀开关检验5、主四路无载通电操作试验6、绝缘电阻测试7、介电强度试验8、结论GGD型交流低压配电柜出厂检验报告第2页（英文版）Two regulations promulgated for implementation is in the party in power for a long time and the rule of law conditions, the implementation of comprehensive strictly strategic plan, implementation in accordance with the rules and discipline to manage the party, strengthen inner-party supervision of major initiatives. The two regulations supporting each other, the < code > adhere to a positive advocate, focusing on morality is of Party members and Party leading cadres can see, enough to get a high standard; < rule > around the party discipline, disciplinary ruler requirements, listed as "negative list, focusing on vertical gauge, draw the party organizations and Party members do not touch the" bottom line ". Here, the main from four square face two party rules of interpretation: the first part introduces two party Revised regulations the necessity and the revision process; the second part is the interpretation of the two fundamental principles of the revision of laws and regulations in the party; the third part introduces two party regulations modified the main changes and needs to grasp several key problems; the fourth part on how to grasp the implementation of the two regulations of the party. < code > and < Regulations > revised the necessity and revisedhistory of the CPC Central Committee the amendment to the Chinese Communist Party members and leading cadres honest politics several guidelines > and < Chinese Communist Party discipline and Punishment Regulations > column 1 by 2015 to strengthen party laws and regulations focus. Two party regulations revision work lasted a Years, pooling the wisdom of the whole party, ideological consensus, draw historical experience, respect for the wisdom of our predecessors, which reflects the unity of inheritance and innovation; follow the correct direction, grasp the limited goals, adhere to the party's leadership, to solve the masses of the people reflect a focus on the problem. The new revision of the < code > and < rule >, reflects the party's 18 and the eighth session of the third, the spirit of the fourth plenary session, reflecting the experience of studying and implementing the General Secretary Xi Jinping series of important speech, reflects the party's eighteen years comprehensive strictly practice. (a) revised two regulations of the party need of < the ICAC guidelines > in < in 1997 Leaders as members of the Communist Party of China clean politics certain criteria (Trial) > based on revised, the promulgation and implementation of January 2010, to strengthen the construction of the contingent of leading cadres play animportant role. But with the party to manage the party strictly administering the deepening, has not been able to fully meet the actual needs. Content is too complicated, "eight prohibition, 52 are not allowed to" hard to remember, and also difficult to put into practice; the second is concisely positive advocated by the lack of prohibited provisions excessive, no autonomy requirements; the third is banned terms and discipline law, both with the party discipline, disciplinary regulations repeat and Criminal law and other laws and regulations repeat; the fourth is to "clean" the theme is not prominent, not for the existing problems, and is narrow, only needle of county-level leading cadres above. < rule > is in 1997 < Chinese Communist Party disciplinary cases (Trial) > based on revision, in December 2003 the promulgation and implementation, to strengthen the construction of the party play very important role. Along with the development of the situation, which many provisions have been unable to fully meet the comprehensive strictly administering the practice needs. One is Ji law, more than half of the provisions and criminal law and other countries laws and regulations Repetition; two is the political discipline regulations is not prominent, not specific, for violation of the party constitution, damage theauthority of Party Constitution of misconduct lack necessary and serious responsibility to pursue; third is the main discipline for the leading cadres, does not cover all Party members. Based on the above situation, need to < the criterion of a clean and honest administration > and < rule > the two is likely to be more relevant regulations first amendment. By revising, really put the authority of Party discipline, the seriousness in the party tree and call up the majority of Party members and cadres of the party constitution of party compasses party consciousness. (II) two party regulations revision process the Central Committee of the Communist Party of China attaches great importance to two regulations revision . Xi Jinping, general books recorded in the Fifth Plenary Session of the eighth session of the Central Commission for Discipline Inspection, on the revised regulations < > made clear instructions. According to the central deployment, the Central Commission for Discipline Inspection from 2014 under six months begin study two regulations revision. The Standing Committee of the Central Commission for Discipline Inspection 4 review revised. Comrade Wang Qishan 14 times held a special meeting to study two regulations revision, amendment clarifies the direction, major issues of principle, path and target,respectively held a forum will listen to part of the province (area) secretary of the Party committee, Secretary of the Discipline Inspection Commission, part of the central ministries and state organs DepartmentThe first party committee is mainly responsible for people, views of experts and scholars and grassroots party organizations and Party members. Approved by the Central Committee of the Communist Party of China, on 7 September 2015, the general office of the Central Committee of the Party issued a notice to solicit the provinces (autonomous regions, municipalities) Party, the central ministries and commissions, state ministries and commissions of the Party (party), the General Political Department of the military, every 3 people organization of Party of two regulations revision opinion. Central Commission for Discipline Inspection of extensive solicitation of opinions, careful study, attracting, formed a revised sent reviewers. In October 8 and October 12, Central Committee Political Bureau Standing Committee and the Political Bureau of the Central Committee After consideration of the two regulations revised draft. On October 18, the Central Committee of the Communist Party of China formally issued two regulations. Can say, two laws amendment concentrated thewisdom of the whole party, embodies the party. Second, < code > and < Regulations > revision of the basic principles of two party regulations revision work and implement the party's eighteen, ten eight plenary, the spirit of the Fourth Plenary Session of the Eleventh Central Committee and General Secretary Xi Jinping important instructions on the revised < low political criterion > and < Regulations >, highlighting the ruling party characteristics, serious discipline, the discipline quite in front of the law, based on the current, a long-term, advance as a whole, with Bu Xiuding independent < rule > and < rule >. Main principle is: first, adhere to the party constitution to follow. The constitution about discipline and self-discipline required specific, awaken the party constitution of party compasses party consciousness, maintaining the authority of the constitution. General Secretary Xi Jinping pointed out that "no rules, no side round. Party constitution is the fundamental law, the party must follow the general rules. In early 2015 held the eighth session of the Central Commission for Discipline Inspection Fifth Plenary Session of the 16th Central Committee, Xi Jinping again pointed out that constitution is the party must follow the general rules, but also the general rules." the revision of the< code > and < rule > is Method in adhere to the regulations established for the purpose of combining rule of virtue is to adhere to the party constitution as a fundamental to follow, the constitution authority set up, wake up the party constitution and party rules the sense of discipline, the party constitution about discipline and self-discipline specific requirements. 4 second is to adhere to in accordance with the regulations governing the party and the party. The Party of rule of virtue "de", mainly refers to the party's ideals and beliefs, excellent traditional style. The revised the < code > closely linked to the "self-discipline", insisting on the positive initiative, for all members, highlight the "vital few", emphasized self-discipline, focusing on the morality, and the majority of Party members and the ideological and moral standards. The revised < > Ji method separately, Ji, Ji Yan to Method, as a "negative list", emphasizing the heteronomy, focusing on vertical gauge. Is this one high and one low, a positive reaction, the strict party discipline and practice results transformation for the integration of the whole party to observe moral and discipline requirements, for the majority of Party members and cadres provides benchmarking and ruler. Third, insist on to. In view of the problems existing in theparty at the present stage, the main problems of Party members and cadres in the aspect of self-discipline and abide by the discipline to make clearly defined, especially the party's eighteen years strict political discipline and political rules, organization and discipline and to implement the central eight provisions of the spirit against the four winds and other requirements into Disciplinary provisions. Not one pace reachs the designated position, focusing on in line with reality, pragmatic and effective. After the revision of major changes, major changes in the < code > and < rule > modified and needs to grasp several key problems (a) < code > < code > adhere to according to regulations governing the party and party with morals in combination, for at the present stage, the leadership of the party members and cadres and Party members in existing main problems of self-discipline, put forward principles, requirements and specifications, showing Communists noble moral pursuit, reflected at all times and in all over the world ethics from high from low 5 common requirements. One is closely linked to the "self-discipline", removal and no direct relation to the provisions of . the second is adhere to a positive advocate, "eight prohibition" 52 are not allowed to "about the content of the" negative list moved into synchronizationamendment < cases >. Three is for all the party members, will apply object from the leadership of the party members and cadres to expand to all Party members, fully embodies the comprehensive strictly required. The fourth is prominent key minority, seize the leadership of the party members and cadres is the key, and put forward higher requirements than the ordinary Party members. Five is to simplify, and strive to achieve concise, easy to understand, easy to remember. The revised < code > is the ruling Party since the first insists on a positive advocate forAll Party members and the self-discipline norms, moral declaration issued to all members of the party and the National People's solemn commitment. > < criterion of a clean and honest administration consists of 4 parts, 18, more than 3600 words. After the revision of the < code >, a total of eight, 281 words, including lead, specification and Party member cadre clean fingered self-discipline norms, etc. Part 3 members low-cost clean and self-discipline, the main contents can be summarized as "four must" "eight code". Lead part, reiterated on ideal and faith, fundamental purpose, the fine traditions and work style, noble sentiments, such as "four must" the principle of requirements, strong tone of self-discipline, The higher request for 6 andsupervised tenet, the foothold in permanent Bao the party's advanced nature and purity, to reflect the revised standards requirements. Members of self-discipline norms around the party members how to correctly treat and deal with the "public and private", "cheap and rot" thrifty and extravagance "bitter music", put forward the "four norms". Party leader cadre clean fingered self-discipline norms for the leadership of the party members and cadres of the "vital few", around the "clean politics", from civil servant of the color, the exercise of power, moral integrity, a good family tradition and other aspects of the leadership of the party members and cadres of the "four norms" < > < norm norm. "The Party member's self-discipline norms" and "party members and leading cadre clean fingered self-discipline norms," a total of eight, collectively referred to as the "eight". "Four must" and "eight" of the content from the party constitution and Party's several generation of leaders, especially Xi Jinping, general secretary of the important discussion, refer to the "three discipline and eight points for attention" statements, and reference some embody the Chinese nation excellent traditional culture essence of epigrams. (2) the revised regulations, the main changes in the revised Regulations > to fully adapt to thestrictly requirements, reflects the according to the regulations governing the law of recognition of deepening, the realization of the discipline construction and Jin Ju. < rule > is party a ruler, members of the basic line and follow. And the majority of Party members and cadres of Party organizations at all levels should adhere to the bottom line of thinking, fear discipline, hold the bottom line, as a preventive measure, to keep the party's advanced nature and purity. 1, respect for the constitution, refinement and discipline. Revised < rule > from comprehensive comb physical constitution began, the party constitution and other regulations of the Party of Party organizations and Party discipline requirements refinement, clearly defined in violation of the party constitution will be in accordance with regulations to give the corresponding disciplinary action. The original 10 categories of misconduct, integration specification for political discipline, discipline, honesty and discipline masses Ji Law and discipline and discipline and other six categories, the content of < rule > real return to Party discipline, for the majority of Party members and listed a "negative list. 7 2, highlighting the political discipline and political rules. > < Regulations according to the stage of the discipline of outstandingperformance, emphasizing political discipline and political rules, organization and discipline, in opposition to the party's leadership and the party's basic theory, basic line, basic program and basic experience, the basic requirement of behavior made prescribed punishment, increase the cliques, against the organization such as violation of the provisions, to ensure that the central government decrees and the Party of centralized and unified. 3, adhere to strict discipline in the law and discipline In front, Ji separated. Revised < Regulations > adhere to the problem oriented, do Ji separated. Any national law existing content, will not repeat the provisions, the total removal of 79 and criminal law, repeat the content of the public security management punishment law, and other laws and regulations. In the general reiterated that party organizations and Party members must conscientiously accept the party's discipline, die van comply with national laws and regulations; at the same time, to investigate violations of Party members and even criminal behavior of Party discipline and responsibility, > < Regulations distinguish five different conditions, with special provisions were made provisions, so as to realize the connection of Party discipline and state law. 4, reflect Wind building and anti-corruptionstruggle of the latest achievements. < rule > the party's eighteen years implement the spirit of the central provisions of the eight, against the requirements of the "four winds" and transformation for disciplinary provisions, reflecting the style construction is always on the road, not a gust of wind. In the fight against corruption out of new problems, increase the trading rights, the use of authority relatives profit and other disciplinary terms. Prominent discipline of the masses, the new against the interests of the masses and ignore the demands of the masses and other disciplinary terms and make provisions of the disposition and the destruction of the party's close ties with the masses.Discipline to protect the party's purpose. 8 of these regulations, a total of three series, Chapter 15, 178, more than 24000 words, after the revision of the regulations a total of 3 series, Chapter 11, 133, 17000 words, divided into "general" and "special provisions" and "Supplementary Provisions" Part 3. Among them, add, delete, modify the provisions of the proportion of up to nearly 90%. 1, the general general is divided into five chapters. The first chapter to the regulations of the guiding ideology, principles and scope of application of the provisions, highlight the strengthening ofthe party constitution consciousness, maintenance the authority of Party Constitution, increase the party organizations and Party members must abide by the party constitution, Yan Centralized centralized, would examine at all levels of the amended provisions implementing and maintaining Party discipline, and consciously accept the party discipline, exemplary compliance with national laws and regulations. The second chapter of discipline concept, disciplinary action types and effects of the regulations, will be a serious warning from the original a year for a year and a half; increase the Party Congress representative, by leaving the party above (including leave probation) punishment, the party organization should be terminated its representative qualification provisions. The third chapter of the disciplinary rules of use prescribed in the discipline rectifying process, non convergence, not close hand classified as severely or heavier punishment. "Discipline straighten "At least eighteen years of five years, these five years is to pay close attention to the provisions of the central eight implementation and anti -" four winds ". The fourth chapter on suspicion of illegal party disciplinary distinguish five different conditions, with special provisions were madeprovisions, to achieve effective convergence of Party and country 9 method. < rule > the provisions of Article 27, Party organizations in the disciplinary review found that party members have committed embezzlement, bribery, dereliction of duty dereliction of duty and other criminal law act is suspected of committing a crime shall give cancel party posts, probation or expelled from the party. The second is < Regulations > Article 28 the provisions of Party organizations in the disciplinary review But found that party members are stipulated in the criminal law, although not involved in a crime shall be investigated for Party discipline and responsibility should be depending on the specific circumstances shall be given a warning until expelled punishment. This situation and a difference is that the former regulation behavior has been suspected of a crime, the feeling is quite strict, and the latter for the behavior not involving crime, only the objective performance of the provisions of the criminal code of behavior, but the plot is a crime to slightly. < Regulations > the 29 provisions, Party organizations in the discipline review found that party members and other illegal behavior, affect the party's image, the damage to the party, the state and the people's interests, we should depend on the situationSeriousness given disciplinary action. The loss of Party members, seriously damaging the party's image of behavior, should be given expelled from the party. At this article is party member is in violation of the criminal law outside the other illegal acts, such as violates the public security administration punishment law, customs law, financial laws and regulations behavior. The fourth is < cases > Article 32 stipulates, minor party members and the circumstances of the crime, the people's Procuratorate shall make a decision not to initiate a prosecution, or the people's court shall make a conviction and exempted from criminal punishment shall be given within the party is removed from his post, probation or expelled from the party. Party members and crime, sheets were fined in accordance with For acts; the principal Ordinance amended the provisions of the preceding paragraph. This is the new content, in order to achieve Ji method effective convergence. Five is < > the thirty third article 10 of the provisions, the Party member due to an intentional crime is sentenced to criminal law (including probation) sheets or additional deprivation of political rights; due to negligence crime and was sentenced to three years or more (excluding three years) a penalty, shall give expelled punishment. Due to negligence crime is convictedand sentenced to three years (including three years) in prison or be sentenced to public surveillance, detention, shall in general be expelled from the party. For the individual may not be expelled from the party, should control Approval. This is followed and retained the original > < Regulations the provisions of punishment party authorization rules and report to a level party organizations. For is "party members with criminal acts, and by the criminal punishment, generally should be expelled from the party". The fifth chapter of probationary Party member of the discipline and discipline after missing members of the treatment and punishment decisions, such as the implementation of the provisions, clear the related party discipline and punishment decision made after, for duties, wages and other relevant alteration formalities for the longest time. 2, sub sub section will the original regulations of10 categories of acts of violation of discipline integration revised into 6 categories, respectively, in violation of the punishments for acts of political discipline "in violation of discipline behavior of punishment" in violation of integrity of disciplinary action points "of violation punishments for acts of mass discipline" "the violation of work discipline, punishment" in violation of discipline of life behaviorpunishment "6 chapters. 3, annex" Supplementary Provisions "clear authority making supplementary provisions of, cases of interpretative organ, as well as regulations implementation time and retroactivity etc.. 11 (3) learning understanding > < regulations needs to grasp several key problems The first problem -- about the violation of political discipline behavior > < new ordinance chapter 6 the political discipline column for the six disciplines, that is the main opposition to Party leadership and the opposition of the basic theory, basic line, basic program and basic experience, basic requirements of misconduct made provisions of the disposition, especially the eighteen since the CPC Central Committee put forward the Yan Mingzheng treatment of discipline and political rules requirements and practical achievements transformation for Discipline article, increase the false debate central policies, cliques, against the organization review, make no discipline of the principle of harmony terms. These are the party's eighteen years in comprehensive strictly Process combined with the practice of rich content. (1) false debate the central policies and undermine the Party of centralized and unified the problem is made in accordance with the provisions of the party constitution. Constitution in general programme requirementsadhere to democratic centralism is one of the requirements of the construction of the party must adhere to the four cardinal. Application of this principle is not only the party the basic organization principle and is also the mass line in party life, it requires that we must fully develop inner-party democracy, respect for the dominant position of Party members, safeguarding the Party member democratic rights, give full play to the enthusiasm and creativity of the party organizations at all levels and Party members, at the same time, also must implement the right concentration, ensure the party's mission < the chaos in unity and concerted action to ensure that the party's decision to get quickly and effectively implementing. The Party Central Committee formulated the major principles and policies, through different channels and ways, fully listen to the party organizations and Party members of the opinions and suggestions, but 12 is some people face to face not to say back blather "" will not say, after the meeting said, "" Taiwan does not say, and nonsense ", in fact, not only disrupt the people thought, some causing serious consequences, the damage to the Party of the centralized and unified, hinder the central policy implementation, but also a serious violation of the democratic system of principles. There is no doubt that shall, inaccordance with the Regulations > 4 Specified in Article 6 to give the appropriate punishment. For did not cause serious consequences, to give criticism and education or the corresponding tissue processing. (2) about the destruction of the party's unity < New Regulations > the forty eighth to fifty second article, to damage Party's unity unified and violation of political discipline, punishment situation made explicit provisions. Article 52 of the new "in the party get round group, gangs seek private gain, cliques, cultivate private forces or through the exchange of interests, for their own to create momentum and other activities to gain political capital, given a serious warning or withdraw from their party posts disposition; if the circumstances are serious, to give Leave a party to observation or expelled from the party. (3) on against the organization review of the provisions of the constitution, party loyalty honesty is party members must comply with the obligations. Members must obey the organization decision, shall not violate the organization decided encounters by asking questions to find organization, rely on the organization, shall not deceive the organization, against the organization. For example, after the investigation does not take the initiative to explain the situation, but to engage inoffensive and defensive alliance, hiding the stolen money is against survey organization, is a violation of the behavior of political discipline. Article 24 of the original > < Regulations, although the provisions of the interference, hinder group review the behavior of the fabric can be severely or 13 Aggravated punishment, but did not put this kind of behavior alone as a discipline for qualitative amount of discipline. > < new regulations increase the Article 57, "anti organization review, one of the following acts, given a warning or serious warning; if the circumstances are relatively serious, giving removed from or placed on probation within the party post; if the circumstances are serious, give expelled from the party: (a) on supply or forged, destroyed, transfer, conceal evidence; (II) to prevent others expose, providing evidence Material; (III) harboring co personnel; (4) to the organization to provide false information, to hide the fact;(5) the him against the acts of the organization review. "< rule > add this clause to the Constitution requires more specific, the previous no punishment in accordance with the definite list and put forward clear punishment in accordance with. (4) about organizing or participating in superstitious activities as < Regulations > about engage in activities of。

低压配电柜检验报告单

低压配电柜检验报告单报告编号：XXXXX检验日期：XXXX年XX月XX日1.检验单位：XXX电器检验有限公司2.被检单位：XXX电气有限公司3.检验仪器：电器安全测试仪、温度测量仪、电量测试仪等4.检验标准：GB7251.1-2024《低压成套开关设备和控制设备》、GB/T2900.11-2024《低压电气设备通用技术条件》等相关标准5.检验内容：低压配电柜的外观尺寸、绝缘强度、工作稳定性及保护等功能。

一、外观尺寸检验1.外观尺寸符合设计要求，外壳板材均匀，无明显缺陷。

2.门锁、门铰链固定牢固，门关闭后无晃动。

3.配电柜开关面板的标识符合要求，易于辨认。

二、绝缘强度检验1.绝缘电阻测试：使用电器安全测试仪对低压配电柜进行绝缘测试，结果显示绝缘电阻均在GB7251.1-2024标准规定的范围内，无低于标准要求的情况。

2.绝缘介质测试：使用温度测量仪对低压配电柜运行时产生的温度进行测量，结果显示温度均在GB/T2900.11-2024标准规定的范围内，无异常。

三、工作稳定性检验1.通电试验：对低压配电柜进行通电测试，观察其开关、控制及保护功能的正常运行情况，结果显示配电柜的各部分均能正常工作。

2.过载保护试验：通过对低压配电柜进行过载试验，验证其保护功能。

在150%额定负载下，配电柜能够及时断开电流，确保系统安全。

四、保护功能检验1.防短路能力检验：对低压配电柜进行防短路能力测试，采用标准化的短路电流进行测试，结果显示配电柜能够迅速切断电流，保护系统安全。

2.过压保护试验：通过对低压配电柜进行过压试验，验证其过压保护功能。

在额定电压2倍的情况下，配电柜能够正常工作并保持系统的稳定性。

五、检验结论根据对低压配电柜的外观尺寸、绝缘强度、工作稳定性及保护等功能进行的检验，结果显示该配电柜符合相关标准的要求，各项参数均在标准范围内，具有良好的安全性和可靠性。

六、存在问题及处理建议1.配电柜的电源接地处存在松动现象，建议重新固定电源接地螺母，保证接地可靠性。

低压配电柜箱试验报告

主电路与辅电路之间
2.5kv/1s
合格
5 绝缘电阻:大于0.5MΩ
绝缘电阻表合格
主电路不同极性的裸导体之间
≥10mm
合格
主电路的裸导体与外壳之间
≥10mm
合格
爬电距离:
6 主电路不同极性的裸导体之间
≥12.5mm
游标卡尺合格
主电路的裸导体与外壳之间
≥12.5mm
合格
隔离距离:
功能单元分离位置时与垂直母线的隔离距离 ≥20mm
低压配电柜(箱)试验报告

日期：
天气：
温度：
台区名称：古王专线鑫财分支前已改造维修工程
序
检查项目及检验要求
检测设备检查结果
连接线,通电操作:
铭牌与标志检查
合格
机械操作元作,联锁,锁扣等部件的有效检查 1 导线和电缆布置是否正确
目测
合格合格
电器安装是否正确
合格
螺钉连接是否接触良好
合格
通电操作各元器件操作及指示应正常
≤100mΩ ≤100mΩ
接地电阻测试仪
合格合格
支架对地
≤100mΩ
合格
断路器开关底座对地
≤100mΩ
合格
介电性能试验：
带电部件和绝缘操作手柄之间
3.75kv/1s
合格
4 带电部件与裸露导电部件之间
2.5kv/1s 耐电压测合格
每个极和连接到裸露导电部件上的其它极之间 2.5kv/1s 试仪
合格
合格
防护等级验证: 7 用目测的方法检查.如有疑问时用直径为2.5mm的试棒，
试棒应不能进入柜体内
Ф2.5mm试棒
合格

低压配电柜检验报告单

手动通电调试
合格
合格
电气操作试验
合格
合格
合格
4
保护电路连续性试验
主接地点与保护电气外壳接地点电阻值＜10mΩ
双臂电桥
合格
5
功能单元互换性试验
抽出插入，分合闸，联锁试操作各5次，相同单元互换试验满足以上要求
人力操作
合格
目测
合格
2
介电强度
带电部件与地之间
60V＜Ui≤300V 2kv
30V＜Ui≤600V
30V＜Ui≤600V
2.5kv/1min无闪络或击穿
低压耐压机
合格
主电路各相之间
合格
辅助电路与地之间
合格
绝艳手柄与地之间
3.75kv/1min无闪络或击穿
合格
3
机械和电气操作试验
机械操作试验
通过设计规定的电压按原理图模拟动作试验，手动、电动操作各5次无异常现象出现。
母线
外观ቤተ መጻሕፍቲ ባይዱ
相序正确，相位标识齐全正确，表面平整，防止电措施良好。
合格
搭接处
铜排接触面平整光滑，无毛刺
塞尺
合格
装配
外观
元件符合图纸要求，紧固件无松动，铭牌正确，接地标记齐全。
目测
合格
主回路间隙（mm）
电气间隙≥10
卷尺
合格
爬电距离≥12
二次配线
连接牢固，端头有标志，敷设应层次分明，牢固。横平竖直，颜色符合设计要求。
低压配电柜检验报告单
低压配电柜实验报告单
项目名称: 永城市2015年小型农田重点县项目第三标段（电力工程）产品型号:GGD 编号：27#
检验项目
技术要求

低压配电柜检验报告

低压配电柜检验报告1. 引言本文是对低压配电柜进行的一次检验报告。

低压配电柜是工业生产中常见的电力设备，用于分配电能并保护电气设备免受过电流、过载、短路等故障的影响。

本次检验报告旨在评估低压配电柜的运行状态和安全性能，以提供必要的参考和改进意见。

2. 检验目的本次检验的主要目的如下：•评估低压配电柜的工作状态，包括电流传输、线路连接等方面。

•测试低压配电柜的安全性能，如过载保护、短路保护等功能。

•检查低压配电柜的绝缘性能，确保其正常运行并防止电击等事故。

3. 检验步骤3.1 线路连接检查首先，对低压配电柜的线路连接进行检查。

检查过程包括以下步骤：1.检查进线电缆的连接是否牢固，并使用电缆钳紧固。

2.检查输出线路的连接情况，确保每个输出线路都与相应设备正确连接。

3.检查中性线和地线的连接是否正确接地，以确保安全操作。

3.2 电流传输测试接下来，对低压配电柜的电流传输能力进行测试。

测试步骤如下：1.将电流表连接到进线电缆上，记录电流表的读数。

2.逐个测试输出线路的电流传输能力，记录每个输出线路的电流值。

3.比较测试结果与设计规格，判断低压配电柜的电流传输能力是否符合要求。

3.3 安全性能测试在完成电流传输测试后，进行低压配电柜的安全性能测试。

测试步骤包括以下内容：1.模拟过载情况，将适当大小的负载接入低压配电柜的输出线路。

2.观察低压配电柜的过载保护功能是否正常，是否能够及时切断电源。

3.模拟短路情况，通过连接合适的负载和短路器测试低压配电柜的短路保护功能。

4.检查低压配电柜短路保护是否正常工作，是否能够及时切断电源。

3.4 绝缘性能测试最后，对低压配电柜的绝缘性能进行测试。

测试步骤如下：1.使用绝缘测试仪器对低压配电柜的各个接线点进行绝缘电阻测试。

2.比较测试结果与要求的绝缘电阻值，判断低压配电柜的绝缘性能是否正常。

4. 检验结果与结论根据以上步骤进行的检验，得出以下结果和结论：•线路连接检查结果良好，所有线路连接牢固且正确。

低压配电柜安装及试运行标准做法6

低压配电柜安装及试运行标准做法（1）工艺流程：设备开箱检查→ 设备搬运→ 配电柜基础安装→ 配电柜稳装→电缆压接→ 柜内配线、校线→ 柜盘调试→ 送电运行验收（2）设备开箱检查：①由建设、监理、供货、施工单位共同进行，并做详细记录。

②柜体外观检查应无损伤变形，油漆完整无损，色泽一致。

③按照设备清单、施工纸及设备技术资料核对设备本体及附件、备件的规格、型号应符合设计要求，附件、备件齐全，产品合格证、技术资料、说明书齐全。

④柜内电器装置及元件，绝缘瓷件齐全，安装牢固，无损伤、裂纹等缺陷。

⑤开箱检查应配合施工进度计划，结合现场条件，吊装手段和设备到货时间的长短灵活安排。

设备开箱后应尽快就位，缩短现场存放时间和开箱后保管时间。

可先作外观检查，柜内检查待就位后进行。

（3）设备搬运：①事先清理道路，保证平整畅通。

搬运时配电柜不允许倒放或侧放，而且要防止翻倒。

柜上精密仪表和继电器必要时可拆除单独搬运。

搬运过程中还要注意仪表、瓷瓶及易碎品的保护。

搬运时不应有冲击或严重振动情况，利用机械牵引时，牵引的着力点应在设备重心以下，以防倾斜。

②设备吊装时，吊索的绳长度应一致。

柜顶部无吊环的吊索应挂在四角主要承力结构处，不得将吊索吊在设备部件上。

③设备进货时间按计划安排，尽量减少现场库存和二次搬运。

如需库存和二次搬运时，应保证库存和运输安全。

（4）基础型钢安装：①在室内地面做好，土建装修做完后先进行基础安装。

②配电柜采用10#槽钢做基础。

按施工图预制加工基础槽钢，先调直，除锈，刷防锈底漆。

③将预制好的基础槽钢焊牢在基础预埋铁上，用水准仪及水平尺找平校正。

找平过程中垫片不得超过三片，焊后清理，打磨，补刷防锈漆。

基础槽钢的安装允许偏差表项目允许偏差检验方法（mm）/m（mm）/全长顶部平直度 1.05拉线，尺量检查侧面平直度 1.05③基础槽钢安装完毕后，将室内接地干线与槽钢两端焊牢。

（5）配电柜稳装：①配电柜应按施工图布置，事先编设备号、位号，按顺序将柜子安放到基础槽钢上。

低压配电柜检验报告

低压配电柜检验报告
有效
---------------
一、检测目的
2.确保本工程的低压配电柜与有关的主体工程技术要求一致；
3.确认低压配电柜运行安全可靠；
4.确保本工程低压配电柜运行的安全性、可靠性、经济性。

二、检测现场
1.检查检测现场温度、湿度和气压是否符合检测要求；
2.检查检测现场是否符合检测规定，无噪声、无易燃易爆气体及其他辐射因素；
3.检查检测现场是否有干扰源，如汽车、电火花等；
4.检查检测线路、电器和电子设备的电源是否正确接入；
5.检查现场各设备的接地线和绝缘接地电阻是否正确接入；
6.检查低压配电柜的安装位置是否符合技术要求，器件、组件及电缆的连接紧固是否正确。

三、检测内容
1.低压配电柜外观检查，检查低压配电柜的外观是否完好，外壳结构是否牢固；
2.低压配电柜内部电气检查，检查低压配电柜内部的电气部件是否安装正确，操作机构是否正确组合，主开关、保护器等连接是否正确；。

低压配电柜产品出厂检验报告

低压配电柜产品出厂检验报告一、产品基本信息：产品名称：低压配电柜产品型号：XXXXX生产日期：XXXX年XX月XX日生产厂家：XXXXX有限公司二、检验项目：1.外观检查：外观无划痕、变形、漏胶等情况。

2.尺寸测量：测量产品的长、宽、高，以确保与设计要求一致。

3.防护等级检测：通过测试确定配电柜的防护等级是否符合设计要求。

4.绝缘电阻检测：测量配电柜的绝缘电阻，以评估绝缘性能。

5.功能性能测试：测试低压配电柜的各项功能，确保各种保护装置能够正常运行。

6.开合闸试验：测试低压配电柜的开合闸动作是否正常、准确。

7.触电保护测试：测试低压配电柜的触电保护装置是否能够有效防止触电事故的发生。

8.电气参数测试：测试低压配电柜的电气参数，如电压、电流、频率等是否符合设计要求。

9.通讯功能测试：测试低压配电柜的通讯功能是否正常，如远程监控、远程操作等。

三、检验结果：1.外观检查：配电柜外观无划痕、变形、漏胶等情况。

2.尺寸测量：配电柜尺寸满足设计要求。

3.防护等级检测：配电柜防护等级符合设计要求。

4.绝缘电阻检测：配电柜绝缘电阻满足要求，无异常情况。

5.功能性能测试：各项功能正常，保护装置能够正常运行。

6.开合闸试验：开合闸动作正常、准确。

7.触电保护测试：触电保护装置能够有效防止触电事故的发生。

8.电气参数测试：电气参数符合设计要求。

9.通讯功能测试：通讯功能正常，远程监控、远程操作等功能可正常使用。

四、结论与建议：根据上述检验结果，我们认为该低压配电柜产品符合设计要求，并可以出厂销售。

建议用户在使用过程中按照使用说明书正确操作、维护设备，以确保设备的正常运行和使用寿命。

同时，厂家应继续加强质量控制，提高产品质量和性能，满足客户的需求和要求。

五、检验人员签名：检验人员：XXX。

低压配电柜检验报告

检验报告
产品名称：低压抽出式开关柜产品型号：GCS出厂编号：1808010
检验报告
产品名称：低压抽出式开关柜产品型号：GCS出厂编号：18080n
检验报告
产品名称：低压抽出式开关柜产品型号：GCS出厂编号：1808012
检验报告
产品名称：低压抽出式开关柜产品型号：GCS出厂编号：1808013
检验报告
产品名称：低压抽出式开关柜产品型号：GCS出厂编号：1808014
检验报告
产品名称：低压抽出式开关柜产品型号：GCS出厂编号：1808015
检验报告
产品名称：低压抽出式开关柜产品型号：GCS出厂编号：1808016
检验报告
产品名称：低压抽出式开关柜产品型号：GCS出厂编号：1808017
检验报告
产品名称：低压抽出式开关柜产品型号：GCS出厂编号：1808018
检验报告
产品名称：低压抽出式开关柜产品型号：GCS出厂编号：1808019
检验员:审核:日期：2018年8月8日。

低压电气柜出厂检验报告

1.1
铭牌
Name pate
内容正确、清晰；安装端正、牢固。
The contents are correct and clear,Assemble is neatly and stable.
1.2
框架结构
Frame structure
框架外形及安装尺寸应符合图纸及工艺要求。
Th.overal.dimension.an.installatio.dimension.shoul.mee.th.requirement.o.drawing.an.technology...
涂色均匀,不反光；漆膜无露底、起皱、流痕、斑点及杂物,有良好的附着力；电镀层无起皮、脱落、发霉及锈蚀现象。
The painting is homogeneous,is free from light reflection,scratches flowing path,flaws and disposals,and it has good abhesive strength.The galvanizing is free from delaminating,mildew and rust.
电气间隙Electrical gap: 23 mm
爬电距离Leakage distance:25 mm
1.5
辅助回路配线Wiring
of
auxiliary circuit
线路整齐美观、牢固,标号清晰、正确。导线颜色、截面、布置方式符合标准及工艺要求；辅助回路电气间隙符合标准规定要求。
The wiring is nest and stable.The symbols are clear and correct.The colour ,cross section and arrangement of wires meet the requirements of standards and technology.

低压配电柜检验报告单

电气防火安全检测报告

交流低压开关柜GGD例行检验报告

低压配电柜检验报告

低压配电柜检验报告单

低压配电柜检验报告单

低压配电柜产品出厂检验报告

低压开关柜合格检验报告

低压试验报告

GGD配电柜出厂检验报告

低压配电柜检验报告单

低压配电柜 箱 试验报告

低压配电柜检验报告单

低压配电柜检验报告

低压配电柜安装及试运行标准做法6

低压配电柜检验报告

低压配电柜产品出厂检验报告

低压配电柜检验报告

低压电气柜出厂检验报告

低压配电柜箱试验报告