老顽童STM32F1开发板原理图
STM32原理图含保护电路
UM0723User manual1 kW three-phase motor control demonstration boardfeaturing L6390 drivers and STGP10NC60KD IGBT 1 IntroductionThis document describes the 1 kW three-phase motor control demonstration board featuringthe L6390 high and low-side drivers and the STGP10NC60KD IGBT. The demonstrationboard is an AC/DC inverter that generates a three-phase waveform for driving three or two-phase motors such as induction motors or PMSM motors up to 1000 W with or withoutsensors.The main device presented in this user manual is a universal, fully evaluated, and populateddesign consisting of a three-phase inverter bridge based on the 600 V STMicroelectronics™IGBT STGP10NC60KD in a TO-220 package mounted on a heatsink, and the L6390 high-voltage high-side and low-side driver featuring an integrated comparator for hardwareprotection features such as overcurrent and overtemperature. The driver also integrates anoperational amplifier suitable for advanced current sensing. Thanks to this advancedcharacteristic, the system has been specifically designed to achieve an accurate and fastconditioning of the current feedback, therefore matching the typical requirements in fieldoriented control (FOC).The board has been designed to be compatible with single-phase mains, supplying from90 VAC to 285 VAC or from 125 VDC to 400 VDC for DC voltage. With reconfiguration of theinput sourcing, the board is suitable also for low-voltage DC applications up to 35 VDC. Thisdocument is associated with the release of the STEVAL-IHM023V2 demonstration board(see Figure1 below).Figure 1.STEVAL-IHM023V2June 2011Doc ID 15870 Rev 41/48Contents UM0723Contents1Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12System introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62.1Main characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62.2Target applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62.3Safety and operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72.3.1General terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72.3.2Demonstration board intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72.3.3Demonstration board installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72.3.4Electrical connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82.3.5Demonstration board operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83Board description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93.1System architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93.2The board schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103.3Circuit description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163.3.1Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163.3.2Inrush limitation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173.3.3Brake function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173.3.4Gate driving circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183.3.5Overcurrent protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183.3.6Current sensing amplifying network . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193.3.7The tachometer and Hall/encoder inputs . . . . . . . . . . . . . . . . . . . . . . . . 233.3.8Temperature feedback and overtemperature protection . . . . . . . . . . . . 234Hardware setting of the STEVAL-IHM023V2 . . . . . . . . . . . . . . . . . . . . . 244.1Hardware settings for six-step (block commutation) control of BLDCmotors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244.2Hardware settings for “Field Oriented Control” (FOC) in single-shunttopology current reading configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . 264.3Hardware settings for FOC in three-shunt configuration . . . . . . . . . . . . . 27 5Description of jumpers, test pins, and connectors . . . . . . . . . . . . . . . 302/48Doc ID 15870 Rev 4UM0723Contents 6Connector placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 7Bill of material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 8PCB layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 9Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 10Using STEVAL-IHM023V2 with STM32 PMSM FOC firmwarelibrary v3.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4410.1Environmental considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4410.2Hardware requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4510.3Software requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4510.4STM32 FOC firmware library v3.0 customization . . . . . . . . . . . . . . . . . . . 45 11Conclusion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 12References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 13Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47Doc ID 15870 Rev 43/48List of tables UM0723 List of tablesTable 1.Current reading configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Table 2.Jumper settings for high-voltage BLDC motor in six-step control. . . . . . . . . . . . . . . . . . . . 24 Table 3.Jumper settings for low-voltage BLDC motor in six-step control . . . . . . . . . . . . . . . . . . . . 25 Table 4.Jumper settings for high-voltage PMAC or generic AC motor in single-shuntFOC control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Table 5.Jumper settings for low-voltage BLDC motor in single-shunt FOC control. . . . . . . . . . . . . 27 Table 6.Jumper settings for FOC of HV PMSM, BLDC, or AC IM in three-shunt configuration for current reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Table 7.Jumper settings for FOC of LV PMSM or BLDC in three-shunt configuration for current reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Table 8.Jumpers description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Table 9.Connector pinout description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Table 10.Testing pins description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Table 11.Bill of material. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Table 12.STEVAL-IHM023V2 motor control workbench parameters . . . . . . . . . . . . . . . . . . . . . . . . 45 Table 13.Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 4/48Doc ID 15870 Rev 4UM0723List of figures List of figuresFigure 1.STEVAL-IHM023V2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Figure 2.Motor control system architecture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Figure 3.STEVAL- IHM023V2 schematic - part 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Figure 4.STEVAL- IHM023V2 schematic - part 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Figure 5.STEVAL- IHM023V2 schematic - part 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Figure 6.STEVAL- IHM023V2 schematic - part 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Figure 7.STEVAL- IHM023V2 schematic - part 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Figure 8.STEVAL- IHM023V2 schematic - part 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Figure 9.Power supply block diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Figure 10.Gate driving network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Figure 11.Overcurrent protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Figure 12.Three-shunt configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Figure 13.Six-step current sensing configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Figure 14.NTC placement on the heatsink. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Figure 15.STEVAL-IHM023V2 connectors placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Figure 16.Silk screen - top side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Figure 17.Silk screen - bottom side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Figure 18.Copper tracks - top side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Figure 19.Copper tracks - bottom side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43Doc ID 15870 Rev 45/48System introduction UM07236/48Doc ID 15870 Rev 42 System introduction2.1 Main characteristicsThe information below lists the converter specification data and the main parameters set forthe STEVAL-IHM023V2 demonstration board.●Minimum input voltage 125 VDC or 90 VAC ●Maximum input voltage 400 VDC or 285 VAC●With applied input voltage doubler - the range is from 65 VAC to 145 VAC ●Voltage range for low-voltage motor control applications from 18 VDC to 35 VDC ●Possibility to use auxiliary +15 V supply voltage ●Maximum output power for motors up to 1000 W ●Regenerative brake control feature ●Input inrush limitation with bypassing relay●+ 15 V auxiliary power supply based on buck converter with VIPer™16●IGBT power switch STGP10NC60KD in TO-220 package - compatible with other ST IGBTs or power MOSFETs in TO-220 package●Fully populated board conception with testing points and isolated plastic safety cover ●Motor control connector for interface with STM3210B-EVAL board and other ST motor control dedicated kits ●Tachometer input ●Hall/encoder inputs●Possibility to connect BEMF daughterboard for sensorless six-step control of BLDC motors●PCB type and size:–Material of PCB - FR-4–Double-sided layout –Copper thickness: 60 µm–T otal dimensions of demonstration board: 127 mm x 180 mm.2.2 Target applications●Washing machines ●Home appliances●Medical applications - rehabilitative beds●High-power, high-efficiency water pumps for heating applications.UM0723System introductionDoc ID 15870 Rev 47/482.3 Safety and operating instructions2.3.1 General termsWarning:During assembly, testing, and operation, the demonstrationboard poses several inherent hazards, including bare wires, moving or rotating parts, and hot surfaces. There is a danger of serious personal injury and damage to property, if the kit or components are improperly used or installed incorrectly. The kit is not electrically isolated from the AC/DC input. The demonstration board is directly linked to the mains voltage. No insulation has been placed between the accessible parts and the high-voltage. All measurement equipment must be isolated from the mains before powering the board. When using an oscilloscope with the demonstration board, it must be isolated from the AC line. This prevents a shock from occurring as a result of touching any single point in the circuit, but does NOT prevent shocks when touching two or more points in the circuit. Do not touch the demonstration board after disconnection from the voltage supply, as several parts and power terminals, which contain energized capacitors, need to be allowed to discharge.All operations involving transportation, installation and use, as well as maintenance, are to be carried out by skilled technical personnel (national accident prevention rules must be observed). For the purpose of these basic safety instructions, “skilled technical personnel” are suitably qualified people who are familiar with the installation, use and maintenance of powered electronic systems.2.3.2 Demonstration board intended useThe STEVAL-IHM023V2 demonstration board is a component designed for demonstration purposes only and is not to be used for electrical installation or machinery. The technical data as well as information concerning the power supply conditions should be taken from the documentation and strictly observed.2.3.3 Demonstration board installationThe installation and cooling of the demonstration kit boards must be in accordance with the specifications and the targeted application.●The motor drive converters are protected against excessive strain. In particular, no components are to be bent or isolating distances altered during the course of transportation or handling.●No contact must be made with other electronic components and contacts.●The boards contain electro-statically sensitive components that are prone to damage through improper use. Electrical components must not be mechanically damaged or destroyed.System introduction UM07238/48Doc ID 15870 Rev 42.3.4 Electrical connectionsApplicable national accident prevention rules must be followed when working on the mainpower supply with a motor drive. The electrical installation must be completed in accordance with the appropriate requirements.2.3.5 Demonstration board operationA system architecture which supplies power to the demonstration board should be equipped with additional control and protective devices in accordance with the applicable safety requirements (e.g. compliance with technical equipment and accident prevention rules).UM0723Board descriptionDoc ID 15870 Rev 49/483 Board description3.1 System architectureA generic motor control system can be basically schematized as the arrangement of fourmain blocks (see Figure 2 below).●A control block - its main task is to accept user commands and motor driveconfiguration parameters and to provide all digital signals to implement the proper motor driving strategy. The ST demonstration board based on the STM32™microcontroller STM3210B-EVAL can be used as a control block thanks to the motor control connector used on the board.●A power block - makes a power conversion from the DC bus transferring to the motor by means of a three-phase inverter topology. The power block is based on high-voltage (high and low-side) drivers (L6390) and power switches (STGP10NC60KD) in TO-220 packages.●The motor itself - the STEVAL-IHM023V2 demonstration board is able to properly drive any PMSM, but the FOC itself is conceived for sinusoidal-shaped BEMF . The demonstration board is also suitable for driving any three or two-phase asynchronous motor or low-voltage BLDC motors.●Power supply block - able to work from 90 VAC to 285 VAC or from 125 VDC to400 VDC. With reconfiguration of the power stage with jumpers, the board can also be used for low-voltage applications from 18 VDC to 35 VDC. By supplying the electronic parts on the board through an external + 15 V connector, the board can be used for a wide voltage range up to 400 VDC. Please refer to Section 4 for detailed settings of the jumpers according to the required application.Referring to the above motor control system architecture, the STEVAL-IHM023V2 includes the power supply and the power block hardware blocks.Board description UM0723 3.2 The board schematic10/48Doc ID 15870 Rev 4Doc ID 15870 Rev 411/4812/48Doc ID 15870 Rev 4Doc ID 15870 Rev 413/4814/48Doc ID 15870 Rev 4Doc ID 15870 Rev 415/483.3 Circuitdescriptionsupply3.3.1 PowerThe power supply in the STEVAL-IHM023V2 demonstration board is implemented asa multifunctional block which allows to supply the inverter in all ranges of input voltage up to285 VAC or 400 VDC. If the input AC voltage does not surpass 145 VAC, it is possible toapply the input voltage doubler, this is done by shorting the W14 jumper. This configurationalmost doubles the input AC voltage to a standard level and allows to evaluate the motorcontrol application with a low level of input AC voltage.For high-voltage applications it is necessary to set W3 jumpers to position “HIGHVOLT AGE”, the auxiliary power supply for supplying all active components on thedemonstration board is implemented as a buck converter based on the U6 VIPer16L whichworks with fixed frequency 60 kHz. The output voltage of the converter is +15 VDC voltagewhich is fed into the L6390 drivers as supply voltage as well as into the linear regulatorL78L33ACD and L78M05ACDT. The linear regulator provides +3.3 VDC and +5 VDC forsupplying the operational amplifiers and other related parts placed on the demonstrationboard. The selection of supply voltage for hardware peripherals placed on the board is donewith jumper W1. In the “3.3 V” position the supply voltage selected is +3.3 V and in the “5 V”position it is +5 V. Thanks to jumper W6, it is possible to supply the connected MCU drivingboard with related supply voltage. In this case, the maximal consumptive current of the MCUunit has not overreached 50 mA. Please refer to the ST released VIPer16LD datasheet forfurther information on this concept.For low-voltage applications, the step-down converter must be disabled by setting the W3jumper to position “<35 V ONL Y”. In this case, the other linear regulator, L7815, isconnected directly on the bus line, to provide auxiliary voltage + 15 VDC.Note:Please note that the voltage range in this kind of application must be in the range + 18 VDC to + 35 VDC.For low-voltage DC motor applications which require a voltage lower than + 18 VDC, a dualsupply mode can be used. Voltage on the input connector is normally linked through powerswitches to the motor and an external auxiliary voltage is fed through the J3 connector froman external power source. The voltage of the external power supply used must be in therange + 14.8 V to + 15.5 V with maximal consumption current 0.5 A.The information regarding the value of the supply bus voltage on the main filteringcapacitors is sensed with the voltage divider built around R2, R4, and R7 and is fed into thededicated control unit through the J5 connector. The proper voltage partitioning for appliedresistors values is 0.0075.The presence of +15 VDC on the board is indicated with green LED D7. For a betterunderstanding of the concept, Figure9 describes the power supply in a block diagram.16/48Doc ID 15870 Rev 4limitation3.3.2 InrushThe input stage of the demonstration board is provided with the 10 Ω NTC resistor toeliminate input inrush current peak during charging of the bulk capacitors. T o achievea higher efficiency of the inverter, it is possible to bypass the NTC after the startup phase.The NTC bypass signal is provided from the MCU board through the J5 connector. Theyellow D27 LED diode is turned off when the inrush NTC is bypassed.The STEVAL-IHM023V2 demonstration board contains only a basic EMI filter based on X2and Y2 capacitors. The main function of this demonstration board is as a universal testingplatform. For this reason, the EMI filter is not able to absorb EMI distortion coming from theinverter for all ranges of the applications used and the design of the filter is up to the user.The EMI filter must be designed according to the motor and final target applications used.The heatsink itself is connected to the earth pin in the input J1 connector. If thedemonstration board is used only with DC voltage, it is recommended to connect theheatsink to a negative voltage potential - common ground.function3.3.3 BrakeThe hardware brake feature has been implemented on the STEVAL-IHM023V2demonstration board. This feature connects the external resistive load applied to the J6connector to the bus to eliminate overvoltage generated when the motor acts asa generator. Such a connected load must be able to dissipate all motor generated energy.The brake feature functions automatically in the case of bus overvoltage. Voltage on the busis sensed through the voltage divider with resistors R23, R24, and R31 and compared to thevoltage reference built around the Zener diode D26. The brake dummy load is switched onwhen voltage on the bus reaches 440 VDC and is switched off when the voltage falls below420 VDC. This voltage level has been chosen to be fully compliant with the possible use offront-end PFC stage. Another possibility, to activate the brake dummy load, is to use theexternal signal coming through the J5 motor connector (PWM_Brake signal) from theconnected MCU board. This function is active with the jumper W5 in position “R_BRAKE”.The brake threshold levels can be modified by calculating R23, R24, and R34 new values.The D28 red LED diode indicates acting brake switch.Doc ID 15870 Rev 417/4818/48Doc ID 15870 Rev 43.3.4 Gate driving circuitThe gates of the switches of the IGBT used are controlled by the L6390D drivers. Pleaserefer to the L6390 datasheet for a detailed analysis of the driver parameters.Figure 10 shows the correct driving of the IGBT. As can be seen, the charging current for the IGBT is different compared to the discharging current due to the diode used. The configuration used provides the best trade-off between efficiency and EMI distortion.Thanks to the high-performance L6390 driver, the deadtime insertion between the HVG and LVG outputs is hardware-guaranteed. In this case, considering the value of the deadtime resistors used to be 47 k Ω, the DT of about 600 ns is applied on the outputs in case:●The deadtime is not present on HIN and LIN inputs signals.●The deadtime present on HIN and LIN inputs is less than hardware-set DT .On the contrary, the hardware-set deadtime is not the sum of the deadtime present on the outputs between LVG and HVG if the deadtime present on the HIN and LIN inputs signals is higher than the hardware-set deadtime.3.3.5 Overcurrent protectionHardware overcurrent protection (OCP) is implemented on the board. This feature takes fulladvantage of the L6390 driver where an internal comparator is implemented. Thanks to the internal connection between the comparator output and shutdown block, the intervention time of the overcurrent protection is extremely low, ranging slightly above 200 ns. Please see Figure 11 below for details of the OCP .Considering that the overcurrent protection acts as soon as the voltage on the CP+ pin of the L6390 rises above (approximately equal to) 0.53 V, and considering the default value of the shunt resistor, it follows that the default value for the maximum allowed current is equal to:Equation 1with the default values this gives:I SHUNT_MAX = 7 AI SHUNTMAXV REF R SHUNT ---------------------1R1R2-------+⎝⎠⎛⎞×=The overcurrent protection can be disabled with software if the W5 jumper is set to the “OCPOFF” position. This may be necessary and is often useful when the user decides to makethe brake operate by turning on the three low-side switches. In fact, if the motor acts asa generator, it's necessary to protect the hardware, preventing the bus voltage fromexceeding a safety threshold. In addition to dissipating the motor energy on a brake resistor,it's possible to short the motor phases, preventing the motor current from flowing throughthe bulk capacitors.Please note that with disabling of the OCP, the demonstration board is not protected againstany overcurrent event.3.3.6 Current sensing amplifying networkThe STEVAL-IHM023V2 motor control demonstration board can be configured to run invarious current reading configuration modes:●Three-shunt configuration - suitable for the use of field oriented control (FOC)●Single-shunt configuration - suitable for the use of FOC in a single-shunt configuration●Single-shunt six-step configuration - suitable for scalar controlConfiguration with a shunt resistor, where voltage amplified with an operational amplifier issensed, was chosen as the current sensing networks. Single-shunt configuration requiresa single op amp, three-shunt configuration requires three op amps. Just for compatibilitypurposes, one of them is common to both basic configurations.The configuration jumpers W10 and W11 allow the user to set the common op amp toachieve the compatibility between single-shunt six-step configuration (suitable for scalarcontrol) and three-shunt or single-shunt FOC current reading configuration.Three-shunt FOC or single-shunt FOC current reading configurationThe details of the three-shunt current sensing reading configuration are shown in Figure12.In this configuration, the alternating signal on the shunt resistor, with positive and negativeDoc ID 15870 Rev 419/4820/48Doc ID 15870 Rev 4values, must be converted to be compatible with the single positive input of themicrocontroller A/D converter used to read the current value. This means that the op amp must be polarized in order to obtain a voltage on the output that makes it possible to measure the symmetrical alternating input signal.The op amp is used in follower mode with the gain of the op amp set by resistor r and R:Equation 2It is possible to calculate the voltage on the output of the op amp, OP OUT - V OUT , as the sum of a bias, V BIAS , and a signal, V SIGN , component equal to: Equation 3T otal gain of the circuit including the resistors’ divider is equal to:Equation 4with the default values this gives:●V BIAS = 1.7 V ●G = 4.3●G TOT = 1.7●Maximum current amplifiable without distortion is 6.5 A.Please observe that the user can modify the max. current value by changing the values ofthe shunt resistors.G R r +r------------=V OUT V SIGN V BIAS+=V BIAS 3.31R1-------1R2-------1R3-------++⎝⎠⎛⎞R3×---------------------------------------------------------G×=V SIGN I R SHUNT×1R1-------1R2-------1R3-------++⎝⎠⎛⎞R1×---------------------------------------------------------G×=G TOT V SIGNV IN ----------------V SIGN R SHUNT I×----------------------------==。
stm32开发板原理图
Y5 1 4 3
C41 0.1uF C0603 VGND IOVDD0 IOVDD1 IOVDD2 6 14 19 CVDD CVDD0 CVDD1 CVDD2 CVDD3 RX TX 5 7 24 31 26 27 4 16 20 21 22 35 38 43 45 C35 0.1uF C0603 VGND C36 0.1uF C0603 C37 0.1uF C0603 C38 0.1uF C0603 R43 100k IOVDD R0603
C76 10uF C0805
U6 6 5 DD+ D+ D5 4 3 2 1 GND ID D+ DVBUS
PD14 PD15 PD0 PD1 PE7 PE8 PE9 PE10 PE11 PE12 PE13 PE14 PE15 PD8 PD9 PD10
PD14 PD15 PD0 PD1 PE7 PE8 PE9 PE10 PE11 PE12 PE13 PE14 PE15 PD8 PD9 PD10
5
4
3
2
1
J1 1 2 3 DC_IN R2 100k R0603 C1 0.1uF C0603 C2 10uF C0805 C3 10uF C0805 R1 179k R0603 8 3 7 1
U1 RT7272 VIN EN RLIM B00T SW FB 2 1 5 + EC2 2 100uF/25V
C42 0.01uF C0603R44 22R R0603 C43 0.01uF C0603 RIGHT R45 22R R0603
AGND
C60 18pF C0603
2
R53 1M R0603 30 31
U57 XI/CLKIN XO TXN TXP RXN RXP LINKLED ACTLED NC1 NC2 NC3 NC4 DNC VBG RSVD1 RSVD2 RSVD3 RSVD4 RSVD5 PMODE2 PMODE1 PMODE0 EXRES1 T0CAP 1V20 RSVD 1 2 5 6 25 27 46 47 12 13 7 18 38 39 40 41 42 43 44 45 10 R58 12.4k R0603 4.7uF C0603 0.01uF C0603 AGND R66 10k R0603 R65 10k R0603 AGND R64 10k R0603 R63 10k R0603 R62 10k R0603 R61 10k R0603 3V3 R60 10k R0603 R59 10k R0603 TXN TXP RXN RXP LINKLED ACTLED
STM F I最小系统原理图
1122334455667788DDCCBBA A1234567891011121314151617181920P13.3VRESETPA14PA13PA15PB3PB4GNDRET.C1103pRESETGNDPWR.C1104PWR.C3104 3.3VPowerPWR.C210uFPWR.C410uF XTAL.C120pF XTAL.C220pF 12X28MHz XTAL16pF XTAL26pFOSC32_IN OSC32_OUT OSC_IN OSC_OUT GNDGNDPOW LED1PWRLED.R13303.3VGND CRYSTALRESET20PIN_JTAGBOOTPin PortMCUPC14PC15PH0PH1GND USB_5VUSB.R122RUSB.R222R VBUS1D-2D+3ID 4GND 5SHIELD16SHIELD27SHIELD38SHIELD49USB.J1USBUSB OTGUSBDM USBDPPA9PA10OTG_VBUSOTG_IDUSB.R3330RPC1OTG_PWR_OUT12USB.P112USB.P3EN 1FLG 2GND 3NC 4OUT8IN 7OUT 6NC 5OTG.U1MIC2025/755VC3104GNDVBUSEN PC2GND R210K3.3V C4104GNDUSB_5V USB_5VFLG12USB.P2FLG FLGVBUSENUSB_5V GNDC1103GNDR110K 3.3VGNDC210uFREST1aveshareWUSB_5V12345678SW1USB_5V 5V 5V 5VSTGNDBOOT03.3V 123S1switch10MXTAL.R210M XTAL.R132.768KPE2<>TRACECLK/FSMC_A23/ETH_MII_TXD31PE3<>TRACED0/FSMC_A192PE4<>TRACED1/FSMC_A20/DCMI_D43PE5<>TRACED2/FSMC_A21/TIM9_CH1/DCMI_D64PE6<>TRACED3/FSMC_A22/TIM9_CH2/DCMI_D75VBAT 6PC13<>RTC_AF18PC14<>OSC32_IN 9PC15<>OSC32_OUT10PF0<>FSMC_A0/I2C2_SDA 16PF1<>FSMC_A1/I2C2_SCL 17PF2<>FSMC_A2/I2C2_SMBA 18PF3<>FSMC_A3<>ADC3_IN919PF4<>FSMC_A4/ADC3_IN1420PF5<>FSMC_A5/ADC3_IN1521VSS_571VDD_562PF6<>TIM10_CH1/FSMC_NIORD/ADC3_IN424PF7<>TIM11_CH1/FSMC_NREG/ADC3_IN525PF8<>TIM13_CH1/FSMC_NIOWR/ADC3_IN626PF9<>TIM14_CH1/FSMC_CD/ADC3_IN727PF10<>FSMC_INTR/ADC3_IN828PH0<>OSC_IN 29PH1<>OSC_OUT 30NRST 31PC0<>OTG_HS_ULPI_STP/ADC123_ IN1032PC1<>ETH_MDC/ADC123_ IN1133PC2<>SPI2_MISO/OTG_HS_ULPI_DIR/ETH_MII_TXD2/ADC123_ IN1234PC3<>SPI2_MOSI/I2S2_SD/OTG_HS_ULPI_NXT/ETH_MII_TX_CLK/ADC123_ IN1335VDD_12136VSSA37VREF+38VDDA 39PA0-WKUP<>USART2_CTS/UART4_TX/ETH_MII_CRS/TIM2_CH1_ETR/TIM5_CH1/TIM8_ETR<>ADC123_IN0/WKUP 40PA1<>USART2_RTS/UART4_RX/ETH_RMII_REF_CLK/ETH_MII_RX_CLK/TIM5_CH2/TIM2_CH2/ADC123_IN141PA2<>USART2_TX/TIM5_CH3/TIM9_CH1/TIM2_CH3/ETH_MDIO/ADC123_IN242PA3<>USART2_RX/TIM5_CH4/TIM9_CH2/TIM2_CH4/OTG_HS_ULPI_D0/ETH_MII_COL/ADC123_IN347VSS_461VDD_449PA4<>SPI1_NSS/SPI3_NSS/USART2_CK/DCMI_HSYNC/OTG_HS_SOF/I2S3_WS<>ADC12_IN4/DAC1_OUT 50PA5<>SPI1_SCK/OTG_HS_ULPI_CK/TIM2_CH1_ETR/TIM8_CHIN<>ADC12_IN5/DAC2_OUT 51PA6<>SPI1_MISO/TIM8_BKIN/TIM13_CH1/DCMI_PIXCLK/TIM3_CH1/TIM1_BKIN/ADC12_IN652PA7<>SPI1_MOSI/TIM8_CH1N/TIM14_CH1/TIM3_CH2/ETH_MII_RX_DV/TIM1_CH1N/RMII_CRS_DV/ADC12_IN753PC4<>ETH_RMII_RX_D0/ETH_MII_RX_D0/ADC12_IN1454PC5<>ETH_RMII_RX_D1/ETH_MII_RX_D1/ADC12_IN1555PB0<>TIM3_CH3/TIM8_CH2N/OTG_HS_ULPI_D1/ETH_MII_RXD2/TIM1_CH2N/ADC12_IN856PB1<>TIM3_CH4/TIM8_CH3N/OTG_HS_ULPI_D2/ETH_MII_RXD3/OTG_HS_INTN/TIM1_CH3N/ADC12_IN957PB2-BOOT158PF11<>DCMI_1259PF12<>FSMC_A660VSS_690VDD_672PF13<>FSMC_A763PF14<>FSMC_A864PF15<>FSMC_A965PG0<>FSMC_A1066PG1<>FSMC_A1167PE7<>FSMC_D4/TIM1_ETR68PE8<>FSMC_D5/TIM1_CH1N 69PE9<>FSMC_D6/TIM1_CH170VSS_7102VDD_782PE10<>FSMC_D7/TIM1_CH2N 73PE11<>FSMC_D8/TIM1_CH274PE12<>FSMC_D9/TIM1_CH3N 75PE13<>FSMC_D10/TIM1_CH376PE14<>FSMC_D11/TIM1_CH477PE15<>FSMC_D12/TIM1_BKIN78PB10<>SPI2_SCK/I2S2_SCK/I2C2_SCL/USART3_TX/OTG_HS_ULPI_D3/ETH_MII_RX_ER/OTG_HS_SCL/TIM2_CH379PB11<>I2C2_SDA/USART3_RX/OTG_HS_ULPI_D4/ETH_RMII_TX_EN/ETH_MII_TX_EN/OTG_HS_SDA/TIM2_CH480VCAP_181VDD_115PB12<>SPI2_NSS/I2S2_WS/I2C2_SMBA/USART3_CK/TIM1_BKIN/CAN2_RX/OTG_HS_ULPI_D5/ETH_RMII_TXD0/ETH_MII_TXD0/OTG_HS_ID 92PB13<>SPI2_SCK/I2S2_SCK/USART3_CTS/TIM1_CH1N/CAN2_TX/OTG_HS_ULPI_D6/ETH_RMII_TXD1/ETH_MII_TXD1<>OTG_HS_ VBUS 93PB14<>SPI2_MISO/TIM1_CH2N/TIM12_CH1/OTG_HS_DM/USART3_RTS/TIM8_CH2N94PB15<>SPI2_MOSI/I2S2_SD/TIM1_CH3N/TIM8_CH3N/TIM12_CH2/OTG_HS_DP/RTC_50Hz 95PD8<>FSMC_D13/USART3_TX 96PD9<>FSMC_D14/USART3_RX 97PD10/FSMC_D15<>USART3_CK 98PD11<>FSMC_A16/USART3_CTS99PD12<>FSMC_A17/TIM4_CH1/USART3_RTS100PD13<>FSMC_A18/TIM4_CH2101VSS_8113VDD_891PD14<>FSMC_D0/TIM4_CH3104PD15<>FSMC_D1/TIM4_CH4105PG2<>FSMC_A12106PG3<>FSMC_A13107PG4<>FSMC_A14108PG5<>FSMC_A15109PG6<>FSMC_INT2110PG7<>FSMC_INT3/USART6_CK111PG8<>USART6_RTS/ETH_PPS_OUT112VSS_9126VDD_9103PC6<>SPI2_MCK/TIM8_CH1/SDIO_D6/USART6_TX/DCMI_D0/TIM3_CH1115PC7<>SPI3_MCK/TIM8_CH2/SDIO_D7/USART6_RX/DCMI_D1/TIM3_CH2116PC8<>TIM8_CH3/SDIO_D0/TIM3_CH3/USART6_CK/DCMI_D2117PC9<>I2S2_CKIN/I2S3_CKIN/MCO2/TIM8_CH4/SDIO_D1/I2C3_SDA/DCMI_D3/TIM3_CH4118PA8<>MCO1/USART1_CK/TIM1_CH1/I2C3_SCL/OTG_FS_SOF119PA9<>USART1_TX/TIM1_CH2/I2C3_SMBA/DCMI_D0<>OTG_FS_ VBUS 120PA10<>USART1_RX/TIM1_CH3/OTG_FS_ID/DCMI_D1121PA11<>USART1_CTS/CAN1_RX/TIM1_CH4/OTG_FS_DM 122PA12<>USART1_RTS/CAN1_TX/TIM1_ETR/OTG_FS_DP 123PA13<>JTMS-SWDIO 124VCAP_2125VSS_222VDD_223PA14<>JTCK-SWCLK137PA15<>JTDI/SPI3_NSS/I2S3_WS/TIM2_CH1_ETR/SPI1_NSS138PC10<>SPI3_SCK/I2S3_SCK/UART4_TX/SDIO_D2/DCMI_D8/USART3_TX 139PC11<>UART4_RX/ SPI3_MISO/SDIO_D3/DCMI_D4/USART3_RX140PC12<>UART5_TX/SDIO_CK/DCMI_D9/SPI3_MOSI/I2S3_SD/USART3_CK 141PD0<>FSMC_D2/CAN1_RX 142PD1<>FSMC_D3/CAN1_TX143PD2<>TIM3_ETR/UART5_RX/SDIO_CMD/DCMI_D11144PD3<>FSMC_CLK/USART2_CTS 145PD4<>FSMC_NOE/USART2_RTS 146PD5<>FSMC_NWE/USART2_TX 147VSS_10135VDD_10114PD6<>FSMC_NWAIT/USART2_RX150PD7<>USART2_CK/FSMC_NE1/FSMC_NCE2151PG9<>USART6_RX/FSMC_NE2/FSMC_NCE3152PG10<>FSMC_NCE4_1/FSMC_NE3153PG11<>FSMC_NCE4_2/ETH_MII_TX_EN154PG12<>FSMC_NE4/USART6_RTS155PG13<>FSMC_A24/USART6_CTS/ETH_MII_TXD0/ETH_RMII _TXD0156PG14<>FSMC_A25/USART6_TX/ETH_MII_TXD1/ETH_RMII_TXD1157VSS_11148VDD_11127PG15<>USART6_CTS/DCMI_D13160PB3<>JTDO/ TRACESWO/SPI3_SCK/I2S3_SCK/TIM2_CH2/SPI1_SCK 161PB4<>NJTRST/SPI3_MISO/TIM3_CH1/SPI1_MISO162PB5<>I2C1_SMBA/CAN2_RX/OTG_HS_ULPI_D7/ETH_PPS_OUT/TIM3_CH2/SPI1_MOSI/SPI3_MOSI/DCMI_D10/I2S3_SD 163PB6<>I2C1_SCL/TIM4_CH1/CAN2_TX/OTG_FS_INTN/DCMI_D5/USART1_TX 164PB7<>I2C1_SDA/FSMC_NL/DCMI_VSYNC/USART1_RX/TIM4_CH2165BOOT0<>VPP 166PB8<>TIM4_CH3/SDIO_D4/TIM10_CH1/DCMI_D6/OTG_FS_SCL/ETH_MII_TXD3/I2C1_SCL/CAN1_RX 167PB9<>SPI2_NSS/I2S2_WS/TIM4_CH4/TIM11_CH1/OTG_FS_SDA/SDIO_D5/DCMI_D7/I2C1_SDA/CAN1_TX168PE0<>TIM4_ETR/FSMC_NBL0/DCMI_D2169PE1<>FSMC_NBL1/DCMI_D3170NC/PDR_ON171VDD_336VDD_13149VDD_14159VDD_15172VSS_12158VSS_114VSS_348PH2<>ETH_MI_CRS 43PH3<>ETH_MI_COL44PH4<>I2C2_SCL/OTG_HS_ULPI_NXT 45PH5<>I2C2_SDA46PH6<>I2C2_SMBA/TIM12_CH1/ETH _MII_RXD283PH7<>I2C3_SCL /ETH _MII_RXD384PH8<>I2C3_SDA /DCMI_HSYNC85PH9<>I2C3_SMBA/TIM12_CH2/DCMI_D086PH10<>TIM5_CH1TIM5_ETR/DCMI_D187PH11<>TIM5_CH2 /DCMI_D288PH12<>TIM5_CH3 /DCMI_D389PH13<>TIM8_CH1N /CAN1_TX/128PH14<>TIM8_CH2N/DCMI_D4129PH15<>TIM8_CH3N/DCMI_D11130PI0<>TIM5_CH4 /SPI2_NSS/ I2S2_WS/DCMI_D13131PI1<>SPI2_SCK/I2S2_CK/DCMI_D8132PI2<>TIM8_CH4/SPI2_MISO/I2S2ext_SD/DCMI_D9133PI3<>TIM8_ETR/SPI2_MOSI/I2S2_SD/DCMI_D10134PI4<>TIM8_BKIN /DCMI_D5173PI5<>TIM8_CH1/DCMI_VSYNC174PI6<>TIM8_CH2 /DCMI_D6175PI7<>TIM8_CH3 /DCMI_D7176PI87PI9<>CAN1_RX11PI10<>ETH _MII_RX_ER 12PI11<>OTG_HS_ULPI_DIR13U1STM32FxxxIPA0PA1PA2PA3PA4PA5PA6PA7PA8PA9PA10PA13PA14PA15PB0PB1PB2PB3PB4PB5PB6PB7PB8PB9PB10PB11PB12PB13PB14PB15PC0PC1PC2PC3PC4PC5PC6PC7PC8PC9PC10PC11PC12PC13PC14PC15PH0PH1PH2PH3PH4PH5PH6PH7PH8PH9PH10PH11PH12PH13PH14PH15PD0PD1PD2PD3PD4PD5PD6PD7PD8PD9PD10PD11PD12PD13PD14PD15PE0PE1PE2PE3PE4PE5PE6PE7PE8PE9PE10PE11PE12PE13PE14PE15PF0PF1PF2PF3PF4PF5PF6PF7PF8PF9PF10PF11PF12PF13PF14PF15PG0PG1PG2PG3PG4PG5PG6PG7PG8PG9PG10PG11PG12PG13PG14PG15PI0PI1PI2PI3PI4PI5PI6PI7PI8PI9PI10PI11BOOT0RESETMCU.C12.2uFGNDMCU.C22.2uF GND3.3V 12VBAT1VBATRTC Battery12VREF+13.3VVREF+VREF.C2104VREF.C11uF GND3.3VGNDMCU.R60R VREF+VBAT 3.3V GND PDR_ONPDR_ONGNDMCU.C51043.3V MCU.C4104GNDMCU.C6104MCU.C9104MCU.C7104MCU.C8104MCU.C10104MCU.C13104MCU.C11104MCU.C12104MCU.C14104MCU.C17104MCU.C15104MCU.C16104USB_P USB_N OTG_DM / PA11OTG_DP / PA12MCU.R20RMCU.R30RMCU.R40RMCU.R50RVBUS LED1VBUSLED.R11KGNDUSB_5VUSB_P USB_NOTG_DM / PA11OTG_DP / PA12PE2PE3PE4PE5PE6VBAT PI8PC13PC14PC15PI9PI10PI11PF0PF1PF2PF3PF4PF5PF6PF7PF8PF9PF10PH0PH1RESET PC0PC1PC2PC3VREF+PA0PA1PA2PH2PH3PH4PH5PA3PA4PA5PA6PA7PC4PC5PB0PB1PB2PF11PF12PF13PF14PF15PG0PG1PE7PE8PE9PE10PE11PE12PE13PE14PE15PB10PB11PH6PH7PH8PH9PH10PH11PH12PB12PB13PB14PB15PD8PD9PD10PD11PD12PD13PD14PD15PG2PG3PG4PG5PG6PG7PG8PC6PC7PC8PC9PA8PA9PA10PA13PH13PH14PH15PI0PI1PI2PI3PA14PA15PC10PC11PC12PD0PD1PD2PD3PD4PD5PD6PD7PG9PG10PG11PG12PG13PG14PG15PB3PB4PB5PB6PB7BOOT0PB8PB9PE0PE1PI4PI5PI6PI7PDR_ON GNDGNDMCU.R110KOSC32_OUT OSC32_IN OSC_IN OSC_OUT1234567891011121314151617181920212223242526272829303132333435363738394041424344454647484950515253545556575859606162636465666768697071727374757677787980P3Header 40X21234567891011121314151617181920212223242526272829303132333435363738394041424344454647484950515253545556575859606162636465666768697071727374757677787980P2Header 40X23.3V 3.3V 3.3V3.3V 3.3V GND GNDGND GNDGND3.3VUSB_P USB_NOTG_DM / PA11OTG_DP / PA125Vin5Vin5VinBYPASS3.3V GND A 1COM2B 3COMP.J1JPAD3BYPASSAVSS.C1104AVCC.C11uFGNDVDDQ 1DQ02VDDQ 3DQ14DQ25GNDQ 6DQ37DQ48VDDQ 9DQ510DQ611GNDQ 12DQ713VDD 14LDQM15WE 16CAS 17RAS 18CS 19BA020BA121A1022A023A124A225A326VDD 27GND28A429A530A631A732A833A934A1135NC 36CKE 37CLK 38UDQM 39NC 40GND 41DQ842VDDQ 43DQ944DQ1045GNDQ 46DQ1147DQ1248VDDQ 49DQ1350DQ1451GNDQ 52DQ1553GND 54*1IS42SI6400JPF0PF1PF2PF3PF4PF5PF12PF13PF14PF15PG0PG1PD14PD15PD0PD1PE7PE8PE9PE10PE11PE12PE13PE14PE15PD8PD9PD10PG4PG5PH6PH5PG15PF11PG8PH7PE0PE13.3V GNDNBL0NBL1BA0BA1CKE1CLK NCAS NRAS NWE NE1A 1COM2B 3COMP.J2JPAD3MCU.C184.7uFMCU.C31045V3.3VVDDAVDDA G 1V o2V i 3REG1AMS1117。
STM32最小系统板原理图
STM32最小系统板原理图
1.电源部分：
STM32最小系统板使用了一个5V的直流电源供电，通过一个稳压电
路将电压稳定在3.3V，供给给STM32芯片。
稳压电路采用了L78L33芯片
来实现。
此外，电源部分还包括一个负载电容和一个滤波电容，用于稳定
电压和滤波。
2.芯片部分：
STM32最小系统板采用了STM32F103C8T6芯片，这是一款基于ARM Cortex-M3内核的微控制器。
此芯片具有72MHz的主频、64KB的Flash和20KB的SRAM。
该芯片与外围电路相连，通过引脚实现与其他器件的通信
和数据传输。
3.外设部分：
STM32最小系统板还包括一些外设，用于扩展芯片的功能。
其中最常
见的外设是LED指示灯，用于显示系统的状态。
此外还包括了一个复位按钮，用于复位系统，以及一个用户按钮，用于用户交互。
此外，还包括了
串口通信模块，用于与计算机或其他外部设备进行通信。
4.数据存储部分：
STM32最小系统板还包括一部分数据存储器件，用于存储数据。
其中
最常见的是闪存芯片，用于存储程序代码。
此外还包括了一个EEPROM芯片，用于存储数据。
这些存储器件通过SPI或其他接口与STM32芯片相连。
以上是STM32最小系统板的原理图解析，介绍了电源部分、芯片部分、外设部分和数据存储部分。
了解STM32最小系统板的原理图可以帮助开发
者更好地理解其工作原理和设计特点，从而更好地进行开发和调试。
STM32开发板原理图
R7
45K DC5V
Y1 C2 22pF
R15 DGND DC3.3V R16 R17
10K 30.PA5-SPI1-SCK 10K 31.PA6-SPI1-MISO 10K 32.PA7-SPI1-MOSI A
DC3.3V C A 8550-PNP Q1 E B
R3 10K R4 1K
104
5 9 4 8 3 7 2 6 1
2.4K
ENC28J60CSS (SSOP-28)
RJ45-HR911105A
1 2 3 4 5 6 7 8
DAT2 CD/DAT3 CMD VDD3V CLK VSS DATA0 DATA1 TF_card
1
DC3.3V
DGND
AT24C02(SO-8)
DC5V
60.PD13-LIGHT-PWM 57.PD10-D15
DB9 DB9RA/F
11
1K
10M以太网
DGND C11 U5 10uF 1 2 3 4 5 6 7 8 9 10 11 12 13 14
SPI1
Vcap Vss CLKO INT WOL SO SI SCK CS RST Vssrx TPINTPIN+ Rbias VDD LEDA LEDB Vddosc OSC2 OSC1 Vssosc Vsspll Vddpll Vddrx Vsstx TPOUT+ TPOUTVddtx DC3.3V 28 C13 103 27 26 25 DC3.3V 24 23 22 21 20 19 18 17 16 15 DGND DC3.3V TPOUT+ R21 TPOUT- R22 DC3.3V RJ 1 DGND 2 LEDA 4 LEDB 8 DGND C17 7 C14 20pF 104 C18 104 5 TPIN+ 3 DGND TPIN6 Y2 DGND R24 1K 9 25MHZ 10 C15 20pF R25 1K 12 L1 11 50 DC3.3V A 50 100nH-0805 B C16 103 DGND DGND TPOUT+ TPOUTTD+ TDGND RD+ RDGLEDA GLEDK YLEDA YLEDK A B