Chemlok adhesive application
Chemlok 6150 胶合剂技术数据表说明书
Chemlok® 6150 Adhesive Technical Data SheetChemlok® 6150 adhesive is a one-coat adhesive usedto bond a variety of elastomers to various metals. It is composed of a mixture of polymers, organic compounds and mineral fillers dissolved or dispersed in an organic solvent system.Chemlok 6150 adhesive provides strong adhesion and environmental resistance to harsh environments. It is anon-chlorinated solvent adhesive that can be applied as a one- or two-coat system.Features and Benefits:Versatile – bonds a wide variety of elastomers to metals, plastics and fabrics; suitable for existing production lines; tolerates a wide variety of stock formulations.Convenient – requires only a single coat for most applications, reducing labor, solvent usage, inventory and shipping costs.Durable – provides rubber tearing bonds; provides superior adhesion to plated metals, lowering scrap rates. Elastomers:• Natural Rubber (NR) • Nitrile (NBR)• Polyisoprene (IR) • Butyl (IIR)• Styrene-butadiene (SBR) • EPDM Polymers• Polybutadiene (BR) • Polyepichlorohydrin (ECO)• Polychloroprene (CR)Application:Surface Preparation – Thoroughly clean metal surfaces prior to application. Remove protective oils, cutting oilsand greases by solvent degreasing or alkaline cleaning. Remove rust, scale or oxide coatings by suitable chemical or mechanical cleaning methods.Apply Chemlok 6150 adhesive to stainless steel, aluminum, brass and other nonferrous substrates within one-half hour after cleaning. For ferrous substrates such as steel, a long layover can be tolerated if no if no rust is formed.For further detailed information on surface preparation of specific substrates, refer to Chemlok Adhesives application guide.Mixing – Thoroughly stir adhesive before use, and agitate sufficiently during use to keep dispersed solids uniformly suspended. If needed, proper dilution for the various application methods is best achieved by experience. Give careful attention to agitation since dilution will accelerate settling.Applying – Apply adhesive by brush, dip, roll coat, spray or any other method that gives a uniform coating and avoids excessive runs and tears.When using Chemlok 6150 adhesive as a one-coat adhesive, the dry film thickness should be 17.8-30.5 micron (0.7-1.2 mil). When used as a covercoat over a primer, the dry film thickness of Chemlok 6150 adhesive should be15.2-20.3 micron (0.6-0.8 mil).Parker LORDEngineered Materials Group 111 LORD DriveCary, NC 27511-7923USAphone +1 877 ASK LORD (275 5673)Values stated in this document represent typical values as not all tests are run on each lot of material produced. For formalized product specifications for specific product end uses, contact the Customer Support Center.Information provided herein is based upon tests believed to be reliable. In as much as Parker LORD has no control over the manner in which others may use this information, it does not guarantee the results to be obtained. In addition, Parker LORD does not guarantee the performance of the product or the results obtained from the use of the product or this information where the product has been repackaged by any third party, including but not limited to any product end-user. Nor does the company make any express or implied warranty of merchantability or fitness for a particular purpose concerning the effects or results of such use.WARNING — USER RESPONSIBILITY . FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE.This document and other information from Parker-Hannifin Corporation, its subsidiaries and authorized distributors provide product or system options for further investigation by users having technical expertise.The user, through its own analysis and testing, is solely responsible for making the final selection of the system and components and assuring that all performance, endurance, maintenance, safety and warning requirements of the application are met. The user must analyze all aspects of the application, follow applicable industry standards, and follow the information concerning the product in the current product catalog and in any other materials provided from Parker or its subsidiaries or authorized distributors.To the extent that Parker or its subsidiaries or authorized distributors provide component or system options based upon data or specifications provided by the user, the user is responsible for determining that such data and specifications are suitable and sufficient for all applications and reasonably foreseeable uses of the components or systems.©2021 Parker Hannifin - All Rights ReservedInformation and specifications subject to change without notice and without liability therefor. Trademarks used herein are the property of their respective owners.Chemlok 6150 Adhesive — Technical Data SheetOD DS4428 07/21 Rev.2Drying/Curing – Allow the applied adhesive to dry until visual examination of the film has shown that all solvent has evaporated. This will take approximately 20-40 minutes at room temperature. Drying time can be shortened by either preheating the metal inserts or oven drying after application. Metal parts may be preheated to a maximum of 65°C (150°F) prior to adhesive application. For coated parts, moderate drying temperatures should be used, but temperatures as high as 149°C (300°F) may be used for very short periods of time. Maximum air flow at minimum temperatures will give the best results.Cleanup – Use solvents such as xylene and MEK to remove adhesive before heat is applied. Once cured, removal by solvent is not possible.Shelf Life/Storage:Shelf life is one year from date of shipment when stored by the recipient in a well ventilated area at 21-27°C (70-80°F) in original, unopened container. Do not store or use near heat, sparks or open flame. Keep container tightly closed when not in use.Chemlok 6150 adhesive is moisture sensitive. Minimizeexposure of the adhesive to moisture during application and storage. Avoid excessive exposure to high humidity.Cautionary Information:Before using this or any Parker LORD product, refer to the Safety Data Sheet (SDS) and label for safe use and handling instructions.For industrial/commercial use only. Must be applied by trained personnel only. Not to be used in household applications. Not for consumer use.。
CHEMLOK 5150 产品安全数据表说明书
USA SAFETY DATA SHEET3000000027601. CHEMICAL PRODUCT AND COMPANY IDENTIFICATIONProduct name: CHEMLOK 5150 Product Use/Class:AdhesiveLORD Corporation 111 LORD DriveCary, NC 27511-7923 USATelephone: 814 868-3180Non-Transportation Emergency: 814 763-2345 Chemtrec 24 Hr Transportation Emergency No.800 424-9300 (Outside Continental U.S. 703 527-3887)EFFECTIVE DATE: 08/07/20172. HAZARDS IDENTIFICATIONGHS CLASSIFICATION:Flammable liquids Category 2 Acute toxicity Oral Category 4Acute toxicity Inhalation - Vapours Category 3Acute toxicity Inhalation - Dust and Mist Category 2 Serious eye damage/eye irritation Category 2A Reproductive toxicity Category 1ASpecific target organ systemic toxicity (single exposure) Category 1 Central nervous system, retina, Systemic toxicity, EyesSpecific target organ systemic toxicity (single exposure) Category 3Specific target organ systemic toxicity (repeated exposure) Category 1 Liver, Central nervous system, Eyes, retina Specific target organ systemic toxicity (repeated exposure) Category 2 Nervous system Hazardous to the aquatic environment - acute hazard Category 3 Hazardous to the aquatic environment - chronic hazard Category 3GHS LABEL ELEMENTS: Symbol(s)Signal WordD ANGERHazard StatementsHighly flammable liquid and vapor. Harmful if swallowed. Fatal if inhaled.Causes serious eye irritation.May damage fertility or the unborn child.Causes damage to organs.(Central nervous system, retina, Systemic toxicity, Eyes) May cause respiratory irritation. May cause drowsiness or dizziness.Causes damage to organs through prolonged or repeated exposure.(Liver, Central nervous system, Eyes, retina) May cause damage to organs through prolonged or repeated exposure.(Nervous system) Harmful to aquatic life.Harmful to aquatic life with long lasting effects.Precautionary StatementsPreventionKeep away from heat/sparks/open flames/hot surfaces. - No smoking.Ground/Bond container and receiving equipment.Use explosion-proof electrical/ventilating/lighting equipment.Use only non-sparking tools.Take precautionary measures against static discharge.Obtain special instructions before use.Do not handle until all safety precautions have been read and understood.Wear protective gloves/protective clothing/eye protection/face protection.Use personal protective equipment as required.Wear respiratory protection.Do not breathe dust/fume/gas/mist/vapors/spray.Wash thoroughly after handling.Do not eat, drink or smoke when using this product.Use only outdoors or in a well-ventilated area.Avoid release to the environment.ResponseIn case of fire: refer to section 5 of SDS for extinguishing media.Immediately call a POISON CENTER or doctor/physician.Specific treatment is urgent (see supplemental first aid instructions on this label).IF INHALED: Remove to fresh air and keep at rest in a position comfortable for breathing.IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower.IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do.Continue rinsing.Rinse mouth.StorageStore in a well-ventilated place. Keep cool.Store in a well-ventilated place. Keep container tightly closed.Store locked up.Disposal:Dispose of contents/container in accordance with waste/disposal laws and regulations of your country or particular locality.Other Hazards:This product contains component(s) which have the following warnings; however based on the GHS classification criteria of your country or locale, the product mixture may be outside the respective category(s).Acute: Vapor harmful; may affect the brain or nervous system causing dizziness, headache or nausea. May cause central nervous system depression characterized by the following progressive steps: headache, dizziness, staggering gait, confusion, unconsciousness or coma. Possible irritation of the respiratory system can occur causing a variety of symptoms such as dryness of the throat, tightness of the chest, and shortness of breath. The silane material in this product can hydrolyze to form ethanol. Ethanol can cause moderate eye irritation, moderate skin irritation; and can be absorbed through the skin causing headache, nausea, and general discomfort. Ethanol is toxic by inhalation. If swallowed, the silane material in this product can hydrolyze in the stomach to form ethanol. Refer to the ethanol warnings on this (M)SDS. Contains methanol; may be harmful or fatal if swallowed; ingestion of methanol may cause blindness or permanent eye damage. Cannot be made non-poisonous. Dermal absorption possible.May cause mild skin irritation.Chronic: May cause kidney damage. May affect the gastrointestinal system. This material contains methanol.Ingestion of methanol may cause permanent eye damage or blindness. ACGIH considers Ethyl alcohol to be an A3 carcinogen (confirmed animal carcinogen with unknown relevance in humans).3. COMPOSITION/INFORMATION ON INGREDIENTSChemical Name CAS Number RangeMethanol67-56-185 - 90%Ethyl alcohol64-17-5 1 - 5%Organic phosphonium chloride salt PROPRIETARY 1 - 5%Any "PROPRIETARY" component(s) in the above table is considered trade secret, thus the specific chemical and its exact concentration is being withheld.4. FIRST AID MEASURESFIRST AID - EYE CONTACT: Flush eyes immediately with large amount of water for at least 15 minutes holding eyelids open while flushing. Get prompt medical attention.FIRST AID - SKIN CONTACT: Flush contaminated skin with large amounts of water while removing contaminated clothing. Wash affected skin areas with soap and water. Get medical attention if symptoms occur.FIRST AID - INHALATION: Move person to fresh air. Restore and support continued breathing. If breathing is difficult, give oxygen. Get immediate medical attention.FIRST AID - INGESTION: If swallowed, do not induce vomiting. Call a physician or poison control center immediately for further instructions. Never give anything by mouth if victim is rapidly losing consciousness, unconscious or convulsing.5. FIRE-FIGHTING MEASURESSUITABLE EXTINGUISHING MEDIA: Carbon Dioxide, Dry Chemical, Foam, Water FogUNSUITABLE EXTINGUISHING MEDIA: Not determined for this product.SPECIFIC HAZARDS POSSIBLY ARISING FROM THE CHEMICAL: Flammable liquid and vapor. Keep containers tightly closed. Isolate from heat, electrical equipment, sparks, open flame, and other sources of ignition. Closed containers may rupture when exposed to extreme heat. Use water spray to keep fire exposed containers cool. During a fire, irritating and/or toxic gases and particulate may be generated by thermal decomposition or combustion.SPECIAL PROTECTIVE EQUIPMENT AND PRECAUTIONS FOR FIRE-FIGHTERS: Wear full firefighting protective clothing, including self-contained breathing apparatus (SCBA). Water spray may be ineffective. If water is used, fog nozzles are preferable.6. ACCIDENTAL RELEASE MEASURESPERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT, AND EMERGENCY PROCEDURES: Remove all sources of ignition (flame, hot surfaces, and electrical, static or frictional sparks). Avoid breathing vapors. Use self-contained breathing equipment. Avoid contact.ENVIRONMENTAL PRECAUTIONS: Do not contaminate bodies of water, waterways, or ditches, with chemical or used container.METHODS AND MATERIALS FOR CONTAINMENT AND CLEANUP: Keep non-essential personnel a safe distance away from the spill area. Notify appropriate authorities if necessary. Contain and remove with inert absorbent material and non-sparking tools. Avoid contact. Before attempting cleanup, refer to hazard caution information in other sections of the SDS form.7. HANDLING AND STORAGEHANDLING: Keep closure tight and container upright to prevent leakage. Ground and bond containers when transferring material. Because empty containers may retain product residue and flammable vapors, keep away from heat, sparks and flame; do not cut, puncture or weld on or near the empty container. Do not smoke where this product is used or stored. Avoid breathing of vapor or spray mists. Use with adequate ventilation. Avoid skin and eye contact. Wash thoroughly after handling. Do not handle until all safety precautions have been read and understood. Empty containers should not be re-used. Cannot be made non-poisonous.STORAGE: Do not store or use near heat, sparks, or open flame. Store drum out of sun and away from heat. Store only in well-ventilated areas. Do not puncture, drag, or slide container. Keep container closed when not in use. Refer to OSHA29CFR Part 1910.106 "Flammable and Combustible Liquids" for specific storage requirements.INCOMPATIBILITY: Strong acids, bases, and strong oxidizers.8. EXPOSURE CONTROLS/PERSONAL PROTECTION COMPONENT EXPOSURE LIMITChemical Name ACGIH TLV-TWA ACGIH TLV-STELOSHA PEL-TWAOSHA PEL-CEILINGSkinMethanol200 ppm250 ppm260 mg/m3200 ppmN.E.SEthyl alcohol N.E.1,000 ppm1,900 mg/m31,000 ppmN.E.N.A.Organic phosphoniumchloride saltN.E.N.E.N.E. N.E.N.A.N.A. - Not Applicable, N.E. - Not Established, S - Skin DesignationEngineering controls: Sufficient ventilation in pattern and volume should be provided in order to maintain air contaminant levels below recommended exposure limits. Caution: Solvent vapors are heavier than air and collect in lower levels of the work area. Sufficient ventilation (using explosion-proof equipment) should be provided to prevent flammable vapor/air mixtures from accumulating.PERSONAL PROTECTION MEASURES/EQUIPMENT:RESPIRATORY PROTECTION: Use a NIOSH approved chemical/mechanical filter respirator designed toremove a combination of particulates and organic vapor if occupational limits are exceeded. For emergencysituations, confined space use, or other conditions where exposure limits may be greatly exceeded, use an approved air-supplied respirator. For respirator use observe OSHA regulations (29CFR 1910.134) or use in accordance with applicable laws and regulations of your country or particular locality.SKIN PROTECTION: Use neoprene, nitrile, or rubber gloves to prevent skin contact.EYE PROTECTION: Use safety eyewear including safety glasses with side shields and chemical goggles where splashing may occur.OTHER PROTECTIVE EQUIPMENT: Use disposable or impervious clothing if work clothing contamination is likely. Remove and wash contaminated clothing before reuse.HYGIENIC PRACTICES: Wash hands before eating, smoking, or using toilet facility. Do not smoke in anychemical handling or storage area. Food or beverages should not be consumed anywhere this product is handled or stored. Wash thoroughly after handling.9. PHYSICAL AND CHEMICAL PROPERTIESTypical values, not to be used for specification purposes.ODOR: Alcohol VAPOR PRESSURE: N.D.APPEARANCE: Clear VAPOR DENSITY: Heavier than Air PHYSICAL STATE: Liquid LOWER EXPLOSIVE LIMIT: 4.3 %(V)FLASH POINT: 43 °F, 6 °C SetaflashClosed CupUPPER EXPLOSIVE LIMIT: 36.5 %(V)BOILING RANGE: 65 - 100 °C EVAPORATION RATE: Faster than n-butyl-acetate.AUTOIGNITION TEMPERATURE:N.D.DENSITY: 0.82 g/cm3 - 6.85 lb/gal DECOMPOSITION TEMPERATURE:N.D. VISCOSITY, DYNAMIC: N.D.ODOR THRESHOLD: N.D.VISCOSITY, KINEMATIC: N.D.SOLUBILITY IN H2O: Insoluble VOLATILE BY WEIGHT: 94.65 %pH: N.A.VOLATILE BY VOLUME: 96.15 %FREEZE POINT: N.D. VOC CALCULATED: 6.33 lb/gal, 758 g/l COEFFICIENT OF WATER/OILDISTRIBUTION:N.D.LEGEND: N.A. - Not Applicable, N.E. - Not Established, N.D. - Not Determined10. STABILITY AND REACTIVITYHAZARDOUS POLYMERIZATION: Hazardous polymerization will not occur under normal conditions.STABILITY: Product is stable under normal storage conditions.CONDITIONS TO AVOID: High temperatures. Sources of ignition.INCOMPATIBILITY: Strong acids, bases, and strong oxidizers.HAZARDOUS DECOMPOSITION PRODUCTS: Oxides of nitrogen, Carbon monoxide, carbon dioxide, Oxides of silicon11. TOXICOLOGICAL INFORMATIONEXPOSURE PATH: Refer to section 2 of this SDS.SYMPTOMS:Refer to section 2 of this SDS.TOXICITY MEASURES:Chemical Name LD50/LC50Methanol Oral LD50: Rat6,200 mg/kgDermal LD50: Rabbit15,800 mg/kgInhalation LC50: Rat22500 ppm/8 hEthyl alcohol Oral LD50: Rat7,060 mg/kgInhalation LC50: Rat124.7 mg/l/4 hOrganic phosphonium chloride salt Oral LD50: Rat43 mg/kgGHS LC50 (vapour): Acute toxicity point estimate3 mg/l GHS LC50 (dustand mist): Acute toxicity point estimate0.05 mg/lGerm cell mutagenicity: No classification proposedCarcinogenicity: No classification proposedReproductive toxicity: Category 1A - May damage fertility or the unborn child.Components contributing to classification: Methanol.12. ECOLOGICAL INFORMATIONECOTOXICITY:Chemical Name EcotoxicityMethanol Fish: Pimephales promelas28,200 mg/l96 h flow-throughPimephales promelas> 100 mg/l96 h StaticOncorhynchus mykiss19,500 - 20,700 mg/l96 h flow-throughLepomis macrochirus13,500 - 17,600 mg/l96 h flow-throughEthyl alcohol Fish: Pimephales promelas> 100 mg/l96 h StaticPimephales promelas13,400 - 15,100 mg/l96 h flow-throughInvertebrates: Daphnia magna9,268 - 14,221 mg/l48 hDaphnia magna2 mg/l48 h StaticOrganic phosphonium chloride salt N.D.PERSISTENCE AND DEGRADABILITY:Not determined for this product.BIOACCUMULATIVE: Not determined for this product.MOBILITY IN SOIL: Not determined for this product.OTHER ADVERSE EFFECTS: Not determined for this product.13. DISPOSAL CONSIDERATIONSDISPOSAL METHOD: Disposal should be done in accordance with Federal (40CFR Part 261), state and local environmental control regulations. If waste is determined to be hazardous, use licensed hazardous waste transporter and disposal facility.14. TRANSPORT INFORMATIONUS DOT RoadDOT Proper Shipping Name: AdhesivesDOT Hazard Class: 3SECONDARY HAZARD: NoneDOT UN/NA Number: 1133Packing Group: IIEmergency Response Guide Number: 128IATA CargoPROPER SHIPPING NAME: AdhesivesDOT Hazard Class: 3HAZARD CLASS: NoneUN-NUMBER: 1133PACKING GROUP: IIEMS: 3LIMDGPROPER SHIPPING NAME: AdhesivesDOT Hazard Class: 3HAZARD CLASS: NoneUN-NUMBER: 1133PACKING GROUP: IIEMS: F-EThe listed transportation classification applies to non-bulk shipments. It does not address regulatory variations due to changes in package size, mode of shipment or other regulatory descriptors. For the most accurate shipping information, refer to your transportation/compliance department.15. REGULATORY INFORMATIONU.S. FEDERAL REGULATIONS: AS FOLLOWS:SARA SECTION 313This product contains the following substances subject to the reporting requirements of Section 313 of Title III of the Superfund Amendment and Reauthorization Act of 1986 and 40 CFR part 372.:Chemical Name CAS Number Weight % Less ThanMethanol67-56-190.0%TOXIC SUBSTANCES CONTROL ACT:INVENTORY STATUSThe chemical substances in this product are on the TSCA Section 8 Inventory.EXPORT NOTIFICATIONThis product contains the following chemical substances subject to the reporting requirements of TSCA 12(B) if exported from the United States:None16. OTHER INFORMATIONUnder HazCom 2012 it is optional to continue using the HMIS rating system. It is important to ensure employees have been trained to recognize the different numeric ratings associated with the HazCom 2012 and HMIS schemes.HMIS RATINGS - HEALTH: 2* FLAMMABILITY: 3 PHYSICAL HAZARD: 1* - Indicates a chronic hazard; see Section 2Revision: Section 2Effective Date: 08/07/2017DISCLAIMERThe information contained herein is, to the best of our knowledge and belief, accurate. However, since the conditions of handling and use are beyond our control, we make no guarantee of results, and assume no liability for damages incurred by use of this material. It is the responsibility of the user to comply with all applicable federal, state and local laws and regulations.。
CHEMLOK 6250 化学产品和公司标识说明书
USA SAFETY DATA SHEET3000000077291. CHEMICAL PRODUCT AND COMPANY IDENTIFICATIONProduct name: CHEMLOK 6250 Product Use/Class:AdhesiveLORD Corporation 111 LORD DriveCary, NC 27511-7923 USATelephone: 814 868-3180Non-Transportation Emergency: 814 763-2345 Chemtrec 24 Hr Transportation Emergency No.800 424-9300 (Outside Continental U.S. 703 527-3887)EFFECTIVE DATE: 11/02/20182. HAZARDS IDENTIFICATIONGHS CLASSIFICATION:Flammable liquids Category 3Skin corrosion/irritation Category 2Serious eye damage/eye irritation Category 2A Skin sensitization Category 1ARespiratory sensitization Category 1 Carcinogenicity Category 2Reproductive toxicity Category 2Specific target organ systemic toxicity (single exposure) Category 3Specific target organ systemic toxicity (single exposure) Category 2 blood systemSpecific target organ systemic toxicity (single exposure) Category 1 Respiratory system, Central nervous system, Kidney, LiverSpecific target organ systemic toxicity (repeated exposure) Category 1 Respiratory system, Nervous system Specific target organ systemic toxicity (repeated exposure) Category 2 Ears, blood system Hazardous to the aquatic environment - acute hazard Category 2 Hazardous to the aquatic environment - chronic hazardCategory 2GHS LABEL ELEMENTS: Symbol(s)Signal WordD ANGERHazard StatementsFlammable liquid and vapor. Causes skin irritation.Causes serious eye irritation.May cause an allergic skin reaction.May cause allergy or asthma symptoms or breathing difficulties if inhaled. Suspected of causing cancer.Suspected of damaging fertility or the unborn child. May cause harm to breast-fed children. May cause drowsiness or dizziness.May cause damage to organs.(blood system)Causes damage to organs.(Respiratory system, Central nervous system, Kidney, Liver)Causes damage to organs through prolonged or repeated exposure.(Respiratory system, Nervous system)May cause damage to organs through prolonged or repeated exposure.(Ears, blood system)Toxic to aquatic life.Toxic to aquatic life with long lasting effects.Precautionary StatementsPreventionKeep away from heat/sparks/open flames/hot surfaces. - No smoking.Ground/Bond container and receiving equipment.Use explosion-proof electrical/ventilating/lighting equipment.Use only non-sparking tools.Take precautionary measures against static discharge.Obtain special instructions before use.Do not handle until all safety precautions have been read and understood.Wear protective gloves/protective clothing/eye protection/face protection.Use personal protective equipment as required.In case of inadequate ventilation wear respiratory protection.Do not breathe dust/fume/gas/mist/vapors/spray.Wash thoroughly after handling.Do not eat, drink or smoke when using this product.Use only outdoors or in a well-ventilated area.Contaminated work clothing should not be allowed out of the workplace.Avoid release to the environment.ResponseIn case of fire: refer to section 5 of SDS for extinguishing media.Call a POISON CENTER or doctor/physician if you feel unwell.IF exposed: Call a POISON CENTER or doctor/physician.Specific treatment (see supplemental first aid instructions on this label).IF INHALED: Remove to fresh air and keep at rest in a position comfortable for breathing.If experiencing respiratory symptoms: Call a POISON CENTER or doctor/physician.IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower.If skin irritation or rash occurs: Get medical advice/attention.IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do.Continue rinsing.Collect spillage.StorageStore in a well-ventilated place. Keep cool.Store in a well-ventilated place. Keep container tightly closed.Store locked up.Disposal:Dispose of contents/container in accordance with waste/disposal laws and regulations of your country or particular locality.Other Hazards:This product contains component(s) which have the following warnings; however based on the GHS classification criteria of your country or locale, the product mixture may be outside the respective category(s).Acute: Vapor harmful; may affect the brain or nervous system causing dizziness, headache or nausea. Possibleirritation of the respiratory system can occur causing a variety of symptoms such as dryness of the throat, tightness of the chest, and shortness of breath. May cause lung damage. Animal tests have indicated that respiratory sensitization can result from skin contact with certain isocyanates. In elevated-temperature applications, product may releasevapors that may produce cyanosis in the absence of sufficient ventilation or adequate respiratory protection. May cause central nervous system depression characterized by the following progressive steps: headache, dizziness,staggering gait, confusion, unconsciousness or coma.May be harmful if swallowed. Ingestion is not an expected route of entry in industrial or commercial uses.Chronic: May affect the gastrointestinal system. May cause long-term lung damage. Ethylbenzene has beenclassified by IARC as a possible human carcinogen (Group 2B) and reported by NTP to show clear evidence forcarcinogenicity in animals. IARC has designated carbon black as Group 2B - inadequate evidence for carcinogenicity in humans, but sufficient evidence in experimental animals. In 2006 IARC reaffirmed its 1995 finding that there is "inadequate evidence" from human health studies to assess whether carbon black causes cancer in humans. Further,epidemiological evidence from well-conducted investigations has shown no causative link between carbon blackexposure and the risk of malignant or non-malignant respiratory disease in humans. The nitrogen substituted aromatic in this product gave positive results for mutagenicity in an Ames Assay study while two other mutagenicity studies proved negative.3. COMPOSITION/INFORMATION ON INGREDIENTSChemical Name CAS Number RangeXylene1330-20-760 - 65%Ethyl benzene100-41-410 - 15%Carbon black1333-86-4 5 - 10%Nitrogen substituted aromatic PROPRIETARY 5 - 10%Aromatic polyisocyanate PROPRIETARY 1 - 5%4,4'-Diphenylmethane diisocyanate101-68-8 1 - 5%2,4-Diphenylmethane diisocyanate5873-54-10.1 - 0.9%Any "PROPRIETARY" component(s) in the above table is considered trade secret, thus the specific chemical and its exact concentration is being withheld.4. FIRST AID MEASURESFIRST AID - EYE CONTACT: Flush eyes immediately with large amount of water for at least 15 minutes holding eyelids open while flushing. Get prompt medical attention.FIRST AID - SKIN CONTACT: Flush contaminated skin with large amounts of water while removing contaminated clothing. Wash affected skin areas with soap and water. Get medical attention if symptoms occur.FIRST AID - INHALATION: Move person to fresh air. Restore and support continued breathing. If breathing is difficult, give oxygen. Get immediate medical attention.FIRST AID - INGESTION: If swallowed, do not induce vomiting. Call a physician or poison control center immediately for further instructions. Never give anything by mouth if victim is rapidly losing consciousness, unconscious or convulsing.5. FIRE-FIGHTING MEASURESSUITABLE EXTINGUISHING MEDIA: Carbon Dioxide, Dry Chemical, Foam, Water FogUNSUITABLE EXTINGUISHING MEDIA: Not determined for this product.SPECIFIC HAZARDS POSSIBLY ARISING FROM THE CHEMICAL: Flammable liquid and vapor. Keep containers tightly closed. Isolate from heat, electrical equipment, sparks, open flame, and other sources of ignition. Closed containers may rupture when exposed to extreme heat. Use water spray to keep fire exposed containers cool. During a fire, irritating and/or toxic gases and particulate may be generated by thermal decomposition or combustion.SPECIAL PROTECTIVE EQUIPMENT AND PRECAUTIONS FOR FIRE-FIGHTERS: Wear full firefighting protective clothing, including self-contained breathing apparatus (SCBA). Water spray may be ineffective. If water is used, fog nozzles are preferable.6. ACCIDENTAL RELEASE MEASURESPERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT, AND EMERGENCY PROCEDURES: Remove all sources of ignition (flame, hot surfaces, and electrical, static or frictional sparks). Avoid contact. Avoid breathing vapors. Use self-contained breathing equipment.ENVIRONMENTAL PRECAUTIONS: Do not contaminate bodies of water, waterways, or ditches, with chemical or used container.METHODS AND MATERIALS FOR CONTAINMENT AND CLEANUP: Keep non-essential personnel a safe distance away from the spill area. Notify appropriate authorities if necessary. Avoid contact. Before attempting cleanup, referto hazard caution information in other sections of the SDS form. Contain and remove with inert absorbent material and non-sparking tools.7. HANDLING AND STORAGEHANDLING: Keep closure tight and container upright to prevent leakage. Ground and bond containers when transferring material. Avoid skin and eye contact. Wash thoroughly after handling. Avoid breathing of vapor or spray mists. Do not handle until all safety precautions have been read and understood. Empty containers should not be re-used. Use with adequate ventilation. Because empty containers may retain product residue and flammable vapors, keep away from heat, sparks and flame; do not cut, puncture or weld on or near the empty container. Do not smoke where this product is used or stored.STORAGE: Do not store or use near heat, sparks, or open flame. Store only in well-ventilated areas. Do not puncture, drag, or slide container. Keep container closed when not in use. Refer to OSHA 29CFR Part 1910.106 "Flammable and Combustible Liquids" for specific storage requirements.INCOMPATIBILITY: Strong bases and oxidizers.; Amines, acids, water, hydroxyl, or active hydrogen compounds.8. EXPOSURE CONTROLS/PERSONAL PROTECTIONCOMPONENT EXPOSURE LIMITChemical Name ACGIH TLV-TWA ACGIH TLV-STELOSHA PEL-TWAOSHA PEL-CEILINGSkinXylene100 ppm150 ppm435 mg/m3100 ppmN.E.N.A.Ethyl benzene20 ppm N.E.435 mg/m3100 ppmN.E.N.A. Carbon black 3 mg/m3N.E. 3.5 mg/m3 N.E.N.A. Nitrogen substituted aromatic N.E.N.E.N.E. N.E.N.A. Aromatic polyisocyanate N.E.N.E.N.E. N.E.N.A.4,4'-Diphenylmethane diisocyanate 0.005 ppm N.E.N.E. 0.2 mg/m30.02 ppmN.A.2,4-Diphenylmethane diisocyanate N.E.N.E.N.E. 0.2 mg/m30.02 ppmN.A.N.A. - Not Applicable, N.E. - Not Established, S - Skin DesignationEngineering controls: Sufficient ventilation in pattern and volume should be provided in order to maintain air contaminant levels below recommended exposure limits. Caution: Solvent vapors are heavier than air and collect in lower levels of the work area. Sufficient ventilation (using explosion-proof equipment) should be provided to prevent flammable vapor/air mixtures from accumulating.PERSONAL PROTECTION MEASURES/EQUIPMENT:RESPIRATORY PROTECTION: Use a NIOSH approved chemical/mechanical filter respirator designed toremove a combination of particulates and organic vapor if occupational limits are exceeded. For emergencysituations, confined space use, or other conditions where exposure limits may be greatly exceeded, use an approved air-supplied respirator. This product contains isocyanates which have poor odor warning properties. If occupational exposure limits are exceeded, a NIOSH approved supplied-air respirator is required. For respirator use observeOSHA regulations (29CFR 1910.134) or use in accordance with applicable laws and regulations of your country or particular locality.SKIN PROTECTION: Use neoprene, nitrile, or rubber gloves to prevent skin contact.EYE PROTECTION: Use safety eyewear including safety glasses with side shields and chemical goggles where splashing may occur.OTHER PROTECTIVE EQUIPMENT: Use disposable or impervious clothing if work clothing contamination is likely. Remove and wash contaminated clothing before reuse.HYGIENIC PRACTICES: Wash hands before eating, smoking, or using toilet facility. Do not smoke in any chemical handling or storage area. Food or beverages should not be consumed anywhere this product is handled or stored. Wash thoroughly after handling.9. PHYSICAL AND CHEMICAL PROPERTIESTypical values, not to be used for specification purposes.ODOR: Solvent VAPOR PRESSURE: N.D.APPEARANCE: Black VAPOR DENSITY: Heavier than Air PHYSICAL STATE: Liquid LOWER EXPLOSIVE LIMIT: 1 %(V)UPPER EXPLOSIVE LIMIT: 7 %(V)FLASH POINT: 80 °F, 26 °C SetaflashClosed CupBOILING RANGE: 136 - 141 °C EVAPORATION RATE: Slower than n-butyl-acetate AUTOIGNITION TEMPERATURE:N.D.DENSITY: 0.96 g/cm3 - 7.95 lb/gal DECOMPOSITION TEMPERATURE:N.D. VISCOSITY, DYNAMIC: ≥100 mPa.s @ 25 °C ODOR THRESHOLD: N.D.VISCOSITY, KINEMATIC: ≥104 mm2/s @ 25 °CSOLUBILITY IN H2O: Insoluble VOLATILE BY WEIGHT: 76.54 %pH: N.A.VOLATILE BY VOLUME: 84.15 %FREEZE POINT: N.D. VOC CALCULATED: 5.92 lb/gal, 709 g/l COEFFICIENT OF WATER/OILN.D.DISTRIBUTION:LEGEND: N.A. - Not Applicable, N.E. - Not Established, N.D. - Not Determined10. STABILITY AND REACTIVITYHAZARDOUS POLYMERIZATION: Hazardous polymerization will not occur under normal conditions. STABILITY: Product is stable under normal storage conditions.CONDITIONS TO AVOID: High temperatures. Sources of ignition.INCOMPATIBILITY: Strong bases and oxidizers.; Amines, acids, water, hydroxyl, or active hydrogen compounds. HAZARDOUS DECOMPOSITION PRODUCTS: Carbon dioxide, carbon monoxide, chlorine, hydrogen chloride, Phosgene, Monomeric isocyanate, traces of hydrogen cyanide, nitrogen dioxide, Oxides of nitrogen11. TOXICOLOGICAL INFORMATIONEXPOSURE PATH: Refer to section 2 of this SDS.SYMPTOMS:Refer to section 2 of this SDS.TOXICITY MEASURES:Chemical Name LD50/LC50Xylene Oral LD50: Rat3,500 mg/kgDermal LD50: Rabbit> 4,350 mg/kgInhalation LC50: Rat29.08 mg/l/4 hEthyl benzene Oral LD50: Rat3,500 mg/kgDermal LD50: Rabbit15,400 mg/kgInhalation LC50: Rat17.4 mg/l/4 hCarbon black Oral LD50: Rat> 15,400 mg/kgDermal LD50: Rabbit> 3 g/kgGHS LC50 (vapour): Acute toxicity point estimate55 mg/lNitrogen substituted aromatic Oral LD50: rat1,100 mg/kgAromatic polyisocyanate Oral LD50: Rat49 g/kgDermal LD50: Rabbit> 9,400 mg/kgDermal LD50: Rabbit> 9.4 g/kgGHS LC50 (vapour): Acute toxicity point estimate11 mg/l GHS LC50(dust and mist): Acute toxicity point estimate1.5 mg/l4,4'-Diphenylmethane diisocyanate Oral LD50: Rat31,600 mg/kgDermal LD50: rabbit> 5,000 mg/kgGHS LC50 (vapour): Acute toxicity point estimate11 mg/l/4 h GHS LC50(dust and mist): Acute toxicity point estimate1.5 mg/l/4 h2,4-Diphenylmethane diisocyanate N.D.Germ cell mutagenicity: No classification proposedCarcinogenicity: Category 2 - Suspected of causing cancer.Components contributing to classification: Ethyl benzene.Reproductive toxicity: Category 2 - Suspected of damaging fertility or the unborn child. May cause harm to breast-fed children.Components contributing to classification: Xylene. Ethyl benzene. Toluene.12. ECOLOGICAL INFORMATIONECOTOXICITY:Chemical Name EcotoxicityXylene Fish: Pimephales promelas13.4 mg/l96 h flow-throughOncorhynchus mykiss2.661 - 4.093 mg/l96 h StaticOncorhynchus mykiss13.5 - 17.3 mg/l96 hLepomis macrochirus13.1 - 16.5 mg/l96 h flow-throughLepomis macrochirus19 mg/l96 hLepomis macrochirus7.711 - 9.591 mg/l96 h StaticPimephales promelas23.53 - 29.97 mg/l96 h StaticCyprinus carpio780 mg/l96 h semi-staticCyprinus carpio> 780 mg/l96 hPoecilia reticulata30.26 - 40.75 mg/l96 h StaticInvertebrates: water flea3.82 mg/l48 hGammarus lacustris0.6 mg/l48 hEthyl benzene Fish: Oncorhynchus mykiss11.0 - 18.0 mg/l96 h StaticOncorhynchus mykiss4.2 mg/l96 h semi-staticPimephales promelas7.55 - 11 mg/l96 h flow-throughLepomis macrochirus32 mg/l96 h StaticPimephales promelas9.1 - 15.6 mg/l96 h StaticPoecilia reticulata9.6 mg/l96 h StaticInvertebrates: Daphnia magna1.8 - 2.4 mg/l48 hPlants: Pseudokirchneriella subcapitata4.6 mg/l72 hPseudokirchneriella subcapitata> 438 mg/l96 hPseudokirchneriella subcapitata2.6 - 11.3 mg/l72 h StaticPseudokirchneriella subcapitata1.7 - 7.6 mg/l96 h StaticCarbon black N.D.Nitrogen substituted aromatic N.D.Aromatic polyisocyanate N.D.4,4'-Diphenylmethane diisocyanate Fish: Species> 1,000 mg/l96 hInvertebrates: Daphnia magna> 1,000 mg/l48 h2,4-Diphenylmethane diisocyanate N.D.PERSISTENCE AND DEGRADABILITY:Not determined for this product.BIOACCUMULATIVE: Not determined for this product.MOBILITY IN SOIL: Not determined for this product.OTHER ADVERSE EFFECTS: Not determined for this product.13. DISPOSAL CONSIDERATIONSDISPOSAL METHOD: Disposal should be done in accordance with Federal (40CFR Part 261), state and local environmental control regulations. If waste is determined to be hazardous, use licensed hazardous waste transporter and disposal facility.14. TRANSPORT INFORMATIONUS DOT RoadProper Shipping Name: AdhesivesHazard Class: 3SECONDARY HAZARD: NoneUN/NA Number: 1133Packing Group: IIIEmergency Response Guide Number: 128IATA CargoPROPER SHIPPING NAME: AdhesivesHazard Class: 3HAZARD CLASS: NoneUN-NUMBER: 1133PACKING GROUP: IIIEMS: 3LIMDGPROPER SHIPPING NAME: AdhesivesHazard Class: 3HAZARD CLASS: NoneUN-NUMBER: 1133PACKING GROUP: IIIEMS: F-EThe listed transportation classification applies to non-bulk shipments. It does not address regulatory variations due to changes in package size, mode of shipment or other regulatory descriptors. For the most accurate shipping information, refer to your transportation/compliance department.15. REGULATORY INFORMATIONU.S. FEDERAL REGULATIONS: AS FOLLOWS:SARA SECTION 313This product contains the following substances subject to the reporting requirements of Section 313 of Title III of the Superfund Amendment and Reauthorization Act of 1986 and 40 CFR part 372.:Chemical Name CAS Number Weight % Less ThanXylene1330-20-765.0%Ethyl benzene100-41-415.0%Aromatic polyisocyanate PROPRIETARY 5.0%4,4'-Diphenylmethane diisocyanate101-68-8 5.0%2,4-Diphenylmethane diisocyanate5873-54-10.9%TOXIC SUBSTANCES CONTROL ACT:INVENTORY STATUSThe chemical substances in this product are on the TSCA Section 8 Inventory.EXPORT NOTIFICATIONThis product contains the following chemical substances subject to the reporting requirements of TSCA 12(B) if exported from the United States:None16. OTHER INFORMATIONUnder HazCom 2012 it is optional to continue using the HMIS rating system. It is important to ensure employees have been trained to recognize the different numeric ratings associated with the HazCom 2012 and HMIS schemes.HMIS RATINGS - HEALTH: 2* FLAMMABILITY: 3 PHYSICAL HAZARD: 0* - Indicates a chronic hazard; see Section 2Revision: Section 2Effective Date: 11/02/2018DISCLAIMERThe information contained herein is, to the best of our knowledge and belief, accurate. However, since the conditions of handling and use are beyond our control, we make no guarantee of results, and assume no liability for damages incurred by use of this material. It is the responsibility of the user to comply with all applicable federal, state and local laws and regulations.。
CHEMLOK 8110 商品安全数据表说明书
USA SAFETY DATA SHEET3000000013401. CHEMICAL PRODUCT AND COMPANY IDENTIFICATIONProduct name: CHEMLOK 8110 Product Use/Class:Aqueous AdhesiveLORD Corporation 111 LORD DriveCary, NC 27511-7923 USATelephone: 814 868-3180Non-Transportation Emergency: 814 763-2345 Chemtrec 24 Hr Transportation Emergency No.800 424-9300 (Outside Continental U.S. 703 527-3887)EFFECTIVE DATE: 08/21/20192. HAZARDS IDENTIFICATIONGHS CLASSIFICATION:Skin sensitization Category 1Reproductive toxicity Category 1BSpecific target organ systemic toxicity (single exposure) Category 1 Respiratory system, Systemic toxicity Specific target organ systemic toxicity (repeated exposure) Category 1 Aspiration hazard Category 1Hazardous to the aquatic environment - acute hazard Category 2 Hazardous to the aquatic environment - chronic hazard Category 2GHS LABEL ELEMENTS: Symbol(s)Signal WordD ANGERHazard StatementsMay cause an allergic skin reaction.May damage fertility or the unborn child.Causes damage to organs.(Respiratory system, Systemic toxicity) Causes damage to organs through prolonged or repeated exposure. May be fatal if swallowed and enters airways. Toxic to aquatic life.Toxic to aquatic life with long lasting effects.Precautionary Statements PreventionObtain special instructions before use.Do not handle until all safety precautions have been read and understood. Wear protective gloves.Use personal protective equipment as required. Do not breathe dust/fume/gas/mist/vapors/spray. Wash thoroughly after handling.Do not eat, drink or smoke when using this product.Contaminated work clothing should not be allowed out of the workplace. Avoid release to the environment.ResponseGet medical advice/attention if you feel unwell.IF exposed: Call a POISON CENTER or doctor/physician.Specific treatment (see supplemental first aid instructions on this label).IF ON SKIN: Wash with plenty of soap and water.If skin irritation or rash occurs: Get medical advice/attention.IF SWALLOWED: Immediately call a POISON CENTER or doctor/physician.Do NOT induce vomiting.Wash contaminated clothing before reuse.Collect spillage.StorageStore locked up.Disposal:Dispose of contents/container in accordance with waste/disposal laws and regulations of your country or particular locality.Other Hazards:This product contains component(s) which have the following warnings; however based on the GHS classification criteria of your country or locale, the product mixture may be outside the respective category(s).Acute: Vapor harmful; may affect the brain or nervous system causing dizziness, headache or nausea. May cause central nervous system depression characterized by the following progressive steps: headache, dizziness, staggering gait, confusion, unconsciousness or coma. Possible irritation of the respiratory system can occur causing a variety of symptoms such as dryness of the throat, tightness of the chest, and shortness of breath. May cause skin and eyeirritation. May be harmful if swallowed. Ingestion is not an expected route of entry in industrial or commercial uses.Chronic: Prolonged or repeated contact may result in dermatitis. Repeated or prolonged solvent overexposure may result in permanent central nervous system damage. Formaldehyde may be released from this product in processes that involve heat. Formaldehyde is a skin and respiratory sensitizer, eye and throat irritant, and acute toxicant.Formaldehyde has been identified by NTP and IARC as a known human carcinogen (IARC 1), and by OSHA as a potential human carcinogen. Workplace exposure to formaldehyde is regulated by OSHA Standard 29 CFR1910.1048. IARC has designated carbon black as Group 2B - inadequate evidence for carcinogenicity in humans, but sufficient evidence in experimental animals. In 2006 IARC reaffirmed its 1995 finding that there is "inadequateevidence" from human health studies to assess whether carbon black causes cancer in humans. Further,epidemiological evidence from well-conducted investigations has shown no causative link between carbon black exposure and the risk of malignant or non-malignant respiratory disease in humans. IARC has designated titanium dioxide (TiO2) as Group 2B – possibly carcinogenic to humans in dust form. However, a number of long termanimal studies and human epidemiology studies evaluating TiO2 and workplace exposure show insufficient evidence for carcinogenic effects. EPA, NTP and OSHA do not designate TiO2 as a carcinogen and ACGIH designates TiO2 as A4 - not classifiable as a human carcinogen. Mortaility from other chronic diseases, including other respiratory diseases, was not associated with exposure to TiO2 dust. TiO2 is not present in this product as a dust and no airborne exposure is expected during application.3. COMPOSITION/INFORMATION ON INGREDIENTSChemical Name CAS Number RangeZinc compound PROPRIETARY 5 - 10%Carbon black1333-86-4 1 - 5%Propylene glycol monomethylether107-98-2 1 - 5%Nonylphenol ethoxylate compound PROPRIETARY0.1 - 0.9%Titanium dioxide13463-67-70.1 - 0.9%Resorcinol108-46-30.1 - 0.9%Any "PROPRIETARY" component(s) in the above table is considered trade secret, thus the specific chemical and its exact concentration is being withheld.The above Nonylphenol ethoxylate compound is listed by ECHA as an SVHC.4. FIRST AID MEASURESFIRST AID - EYE CONTACT: Flush eyes immediately with large amount of water for at least 15 minutes holding eyelids open while flushing. Get prompt medical attention.FIRST AID - SKIN CONTACT: Flush contaminated skin with large amounts of water while removing contaminated clothing. Wash affected skin areas with soap and water. Get medical attention if symptoms occur.FIRST AID - INHALATION: Move person to fresh air. Restore and support continued breathing. If breathing is difficult, give oxygen. Get immediate medical attention.FIRST AID - INGESTION: If swallowed, do not induce vomiting. Call a physician or poison control center immediately for further instructions. Never give anything by mouth if victim is rapidly losing consciousness, unconscious or convulsing.5. FIRE-FIGHTING MEASURESSUITABLE EXTINGUISHING MEDIA: Carbon Dioxide, Dry Chemical, Foam, Water FogUNSUITABLE EXTINGUISHING MEDIA: Not determined for this product.SPECIFIC HAZARDS POSSIBLY ARISING FROM THE CHEMICAL: Keep containers tightly closed. Closed containers may rupture when exposed to extreme heat. Use water spray to keep fire exposed containers cool. During a fire, irritating and/or toxic gases and particulate may be generated by thermal decomposition or combustion.SPECIAL PROTECTIVE EQUIPMENT AND PRECAUTIONS FOR FIRE-FIGHTERS: Wear full firefighting protective clothing, including self-contained breathing apparatus (SCBA). If water is used, fog nozzles are preferable.6. ACCIDENTAL RELEASE MEASURESPERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES: Avoid contact. Avoid breathing vapors. Use appropriate respiratory protection for large spills or spills in confined area.ENVIRONMENTAL PRECAUTIONS: Do not contaminate bodies of water, waterways, or ditches, with chemical or used container.METHODS AND MATERIALS FOR CONTAINMENT AND CLEANUP: Keep non-essential personnel a safe distance away from the spill area. Notify appropriate authorities if necessary. Avoid contact. Before attempting cleanup, refer to hazard caution information in other sections of the SDS form. Contain and remove with inert absorbent material.7. HANDLING AND STORAGEHANDLING: Keep closure tight and container upright to prevent leakage. Avoid skin and eye contact. Wash thoroughly after handling. Do not handle until all safety precautions have been read and understood. Empty containers should not be re-used. Use with adequate ventilation.STORAGE: Store only in well-ventilated areas. Keep from freezing. Keep container closed when not in use.INCOMPATIBILITY: Strong acids, bases, and strong oxidizers.8. EXPOSURE CONTROLS/PERSONAL PROTECTIONCOMPONENT EXPOSURE LIMITChemical Name ACGIH TLV-TWA ACGIH TLV-STELOSHA PEL-TWAOSHA PEL-CEILINGSkinZinc compound 2 mg/m310 mg/m3 5 mg/m3 N.E.N.A.Carbon black 3 mg/m3N.E. 3.5 mg/m3 N.E.N.A. Propylene glycolmonomethylether100 ppm150 ppm N.E. N.E.N.A.Nonylphenol ethoxylatecompoundN.E.N.E.N.E. N.E.N.A.Titanium dioxide10 mg/m3N.E.15 mg/m3 N.E.N.A.Resorcinol10 ppm20 ppm N.E. N.E.N.A.N.A. - Not Applicable, N.E. - Not Established, S - Skin DesignationEngineering controls: Sufficient ventilation in pattern and volume should be provided in order to maintain air contaminant levels below recommended exposure limits.PERSONAL PROTECTION MEASURES/EQUIPMENT:RESPIRATORY PROTECTION: Use a NIOSH approved chemical/mechanical filter respirator designed toremove a combination of particulates and organic vapor if occupational limits are exceeded. For emergencysituations, confined space use, or other conditions where exposure limits may be greatly exceeded, use an approved air-supplied respirator. For respirator use observe OSHA regulations (29CFR 1910.134) or use in accordance with applicable laws and regulations of your country or particular locality. Note: If the exposure limit for formaldehyde is exceeded, a formaldehyde-specific, formaldehyde/organic vapor combination, or airline respirator may be required.SKIN PROTECTION: Use neoprene, nitrile, or rubber gloves to prevent skin contact.EYE PROTECTION: Use safety eyewear including safety glasses with side shields and chemical goggles where splashing may occur.OTHER PROTECTIVE EQUIPMENT: Remove and wash contaminated clothing before reuse.HYGIENIC PRACTICES: Wash hands before eating, smoking, or using toilet facility. Do not smoke in anychemical handling or storage area. Food or beverages should not be consumed anywhere this product is handled or stored. Wash thoroughly after handling.9. PHYSICAL AND CHEMICAL PROPERTIESTypical values, not to be used for specification purposes.ODOR: Mild VAPOR PRESSURE: N.D.APPEARANCE: Gray VAPOR DENSITY: Heavier than Air PHYSICAL STATE: Liquid LOWER EXPLOSIVE LIMIT: 1.6 %(V)FLASH POINT:≥ 201 °F, 93 °CUPPER EXPLOSIVE LIMIT: 13.8 %(V)Setaflash Closed CupBOILING RANGE: 100 - 120 °C EVAPORATION RATE: Slower than n-butyl-acetate AUTOIGNITION TEMPERATURE:N.D.DENSITY: 1.16 g/cm3 - 9.67 lb/gal DECOMPOSITION TEMPERATURE:N.D. VISCOSITY, DYNAMIC: ≥20 mPa.s @ 25 °C ODOR THRESHOLD: N.D.VISCOSITY, KINEMATIC: ≥17 mm2/s @ 25 °CSOLUBILITY IN H2O: Water Dispersible VOLATILE BY WEIGHT: 64.55 %pH: 6.5VOLATILE BY VOLUME: 75.28 %FREEZE POINT: 32 F VOC CALCULATED: 1.23 lb/gal, 148 g/l COEFFICIENT OF WATER/OILN.D. METHOD 24: 1.70 lb/gallonDISTRIBUTION:LEGEND: N.A. - Not Applicable, N.E. - Not Established, N.D. - Not Determined10. STABILITY AND REACTIVITYHAZARDOUS POLYMERIZATION: Hazardous polymerization will not occur under normal conditions. STABILITY: Product is stable under normal storage conditions.CONDITIONS TO AVOID: High temperatures. Sources of ignition.INCOMPATIBILITY: Strong acids, bases, and strong oxidizers.HAZARDOUS DECOMPOSITION PRODUCTS: May contain CO, CO2, oxides of nitrogen, oxides of sulfur, halogenated by-products, Metal oxides11. TOXICOLOGICAL INFORMATIONEXPOSURE PATH: Refer to section 2 of this SDS.SYMPTOMS:Refer to section 2 of this SDS.TOXICITY MEASURES:Chemical Name LD50/LC50Zinc compound Oral LD50: Rat> 5,000 mg/kgGHS LC50 (vapour): Acute toxicity point estimate55 mg/l Carbon black Oral LD50: Rat> 15,400 mg/kgDermal LD50: Rabbit> 3 g/kgGHS LC50 (vapour): Acute toxicity point estimate55 mg/l Propylene glycol monomethylether Oral LD50: Rat5,000 mg/kgDermal LD50: Rabbit13 g/kgGHS LC50 (vapour): Acute toxicity point estimate11 mg/l GHS LC50(dust and mist): Acute toxicity point estimate1.5 mg/l Inhalation LC50:Rat>7559 ppm/6 hNonylphenol ethoxylate compound N.D.Titanium dioxide Oral LD50: Rat> 10,000 mg/kgDermal LD50: rabbit> 5,000 mg/kgGHS LC50 (vapour): Acute toxicity point estimate55 mg/l Resorcinol Oral LD50: Rat202 mg/kgDermal LD50: Rabbit3,360 mg/kgInhalation LC50: Rat21.3 mg/l/1 hGerm cell mutagenicity: No classification proposedCarcinogenicity: No classification proposedReproductive toxicity: Category 1B - May damage fertility or the unborn child.Components contributing to classification: Methanol.12. ECOLOGICAL INFORMATIONECOTOXICITY:Chemical Name EcotoxicityZinc compound N.D.Carbon black N.D.Propylene glycol monomethylether Fish: Pimephales promelas20.8 g/l96 h StaticInvertebrates: Daphnia magna23,300 mg/l48 hNonylphenol ethoxylate compound N.D.Titanium dioxide N.D.Resorcinol Fish: Pimephales promelas36 - 100 mg/l96 h StaticPimephales promelas100 mg/l96 h flow-throughOncorhynchus mykiss> 100 mg/l96 h flow-throughPimephales promelas53.4 mg/l96 hInvertebrates: Daphnia magna78 mg/l48 hPERSISTENCE AND DEGRADABILITY:Not determined for this product. BIOACCUMULATIVE: Not determined for this product.MOBILITY IN SOIL: Not determined for this product.OTHER ADVERSE EFFECTS: Not determined for this product.13. DISPOSAL CONSIDERATIONSDISPOSAL METHOD: Disposal should be done in accordance with Federal (40CFR Part 261), state and local environmental control regulations. If waste is determined to be hazardous, use licensed hazardous waste transporter and disposal facility.14. TRANSPORT INFORMATIONUS DOT RoadProper Shipping Name: Environmentally hazardous substances, liquid, n.o.s.Hazard Class: 9SECONDARY HAZARD: NoneUN/NA Number: 3082Packing Group: IIIEmergency Response Guide Number: 171For US DOT non-bulk road shipments this material may be classified as NOT REGULATED. For the mostaccurate shipping information, refer to your transportation/compliance department regarding changes inpackage size, mode of shipment or other regulatory descriptors.IATA CargoPROPER SHIPPING NAME: Environmentally hazardous substance, liquid, n.o.s.Hazard Class: 9HAZARD CLASS: NoneUN NUMBER: 3082PACKING GROUP: IIIEMS: 9LIMDGPROPER SHIPPING NAME: Environmentally hazardous substance, liquid, n.o.s.Hazard Class: 9HAZARD CLASS: NoneUN NUMBER: 3082PACKING GROUP: IIIEMS: F-AThe listed transportation classification applies to non-bulk shipments. It does not address regulatory variations due to changes in package size, mode of shipment or other regulatory descriptors. For the most accurate shipping information, refer to your transportation/compliance department.15. REGULATORY INFORMATIONU.S. FEDERAL REGULATIONS: AS FOLLOWS:SARA SECTION 313This product contains the following substances subject to the reporting requirements of Section 313 of Title III of the Superfund Amendment and Reauthorization Act of 1986 and 40 CFR part 372.:Chemical Name CAS Number Weight % Less ThanZinc compound PROPRIETARY10.0%TOXIC SUBSTANCES CONTROL ACT:INVENTORY STATUSThe chemical substances in this product are on the TSCA Section 8 Inventory.EXPORT NOTIFICATIONThis product contains the following chemical substances subject to the reporting requirements of TSCA 12(B) if exported from the United States:None16. OTHER INFORMATIONUnder HazCom 2012 it is optional to continue using the HMIS rating system. It is important to ensure employees have been trained to recognize the different numeric ratings associated with the HazCom 2012 and HMIS schemes.HMIS RATINGS - HEALTH: 2* FLAMMABILITY: 1 PHYSICAL HAZARD: 0* - Indicates a chronic hazard; see Section 2Revision: Section 2, Section 11Effective Date: 08/21/2019DISCLAIMERThe information contained herein is, to the best of our knowledge and belief, accurate. However, since the conditions of handling and use are beyond our control, we make no guarantee of results, and assume no liability for damages incurred by use of this material. It is the responsibility of the user to comply with all applicable federal, state and local laws and regulations.。
lord 公司的水溶液性胶合剂 CHEMLOK 8560D 安全数据表 说明书
USA SAFETY DATA SHEET1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATIONProduct name:CHEMLOK 8560DProduct Use/Class: Aqueous AdhesiveLORD Corporation111 LORD DriveCary, NC 27511-7923 USATelephone: 814 868-3180Non-Transportation Emergency: 814 763-2345Chemtrec 24 Hr Transportation Emergency No.800 424-9300 (Outside Continental U.S. 703 527-3887)EFFECTIVE DATE: 06/30/20212. HAZARDS IDENTIFICATIONGHS CLASSIFICATION:Serious eye damage/eye irritation Category 2ASkin sensitization Category 1ACarcinogenicity Category 2Specific target organ systemic toxicity (single exposure) Category 2 blood systemSpecific target organ systemic toxicity (single exposure) Category 1 Respiratory system, Systemic toxicity Specific target organ systemic toxicity (repeated exposure) Category 2 blood systemSpecific target organ systemic toxicity (repeated exposure) Category 1 LungsHazardous to the aquatic environment - acute hazard Category 2Hazardous to the aquatic environment - chronic hazard Category 2GHS LABEL ELEMENTS:Symbol(s)Signal WordD ANGERHazard StatementsCauses serious eye irritation.May cause an allergic skin reaction.Suspected of causing cancer.May cause damage to organs.(blood system)Causes damage to organs.(Respiratory system, Systemic toxicity)May cause damage to organs through prolonged or repeated exposure.(blood system)Causes damage to organs through prolonged or repeated exposure.(Lungs)Toxic to aquatic life.Toxic to aquatic life with long lasting effects.Precautionary StatementsPreventionObtain special instructions before use.Do not handle until all safety precautions have been read and understood.Wear protective gloves/eye protection/face protection.Use personal protective equipment as required.Do not breathe dust/fume/gas/mist/vapors/spray.Wash thoroughly after handling.300000005458Do not eat, drink or smoke when using this product.Contaminated work clothing should not be allowed out of the workplace.Avoid release to the environment.ResponseGet medical advice/attention if you feel unwell.IF exposed: Call a POISON CENTER or doctor/physician.Specific treatment (see supplemental first aid instructions on this label).IF ON SKIN: Wash with plenty of soap and water.If skin irritation or rash occurs: Get medical advice/attention.IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do.Continue rinsing.If eye irritation persists: Get medical advice/attention.Wash contaminated clothing before reuse.Collect spillage.StorageStore locked up.Disposal:Dispose of contents/container in accordance with waste/disposal laws and regulations of your country or particular locality.Other Hazards:This product contains component(s) which have the following warnings; however based on the GHS classification criteria of your country or locale, the product mixture may be outside the respective category(s).Acute: In elevated-temperature applications, product may release vapors that may produce cyanosis in the absence of sufficient ventilation or adequate respiratory protection. May be harmful if swallowed. Ingestion is not an expected route of entry in industrial or commercial uses. This product contains a residual amount of a chemical substance that may cause an allergic skin and/or respiratory reaction.Causes mild skin irritation.Chronic: Prolonged or repeated contact may result in dermatitis. The nitrogen substituted aromatic in this product gave positive results for mutagenicity in an Ames Assay study while two other mutagenicity studies proved negative.IARC has identified the proprietary curative in this product as an "animal suspected" carcinogen, Group 3, which downgrades a previous NCI report of it as an "animal positive" carcinogen. IARC has designated carbon black as Group 2B - inadequate evidence for carcinogenicity in humans, but sufficient evidence in experimental animals. In 2006 IARC reaffirmed its 1995 finding that there is "inadequate evidence" from human health studies to assesswhether carbon black causes cancer in humans. Further, epidemiological evidence from well-conductedinvestigations has shown no causative link between carbon black exposure and the risk of malignant or non-malignant respiratory disease in humans.withheld.The above Nonylphenol ethoxylate compound is listed by ECHA as an SVHC.FIRST AID - EYE CONTACT: Flush eyes immediately with large amount of water for at least 15 minutes holding eyelids open while flushing. Get prompt medical attention.FIRST AID - SKIN CONTACT: Flush contaminated skin with large amounts of water while removing contaminated clothing. Wash affected skin areas with soap and water. Get medical attention if symptoms occur.FIRST AID - INHALATION: Move person to fresh air. Restore and support continued breathing. If breathing is difficult, give oxygen. Get immediate medical attention.FIRST AID - INGESTION: If swallowed, do not induce vomiting. Call a physician or poison control center immediately for further instructions. Never give anything by mouth if victim is rapidly losing consciousness, unconscious or convulsing.SUITABLE EXTINGUISHING MEDIA: Carbon Dioxide, Dry Chemical, Foam, Water FogUNSUITABLE EXTINGUISHING MEDIA: Not determined for this product.SPECIFIC HAZARDS POSSIBLY ARISING FROM THE CHEMICAL: Keep containers tightly closed. Closed containers may rupture when exposed to extreme heat. Use water spray to keep fire exposed containers cool. WARNING: Due to the combustible nature of the dried film of this product and the potential for smoldering or fire, the accumulation and buildup of the dried film on spray booth walls and floors, spindles, fixtures and other surfaces should be avoided, and any buildup should be removed. Keep the dried film accumulations away from sparks, friction, impact, high heat (>235 F/>112 C) or other sources of ignition. These conditions could cause the dried film to ignite very readily and quickly, and the resulting smoldering or fire may be difficult to extinguish. During removal of accumulation/buildup of this product, take precautions to avoid heat, friction and impact during the cleaning process. Use paint stripper, brass brush, or plastic scraper for cleaning. In the event of smoldering or a fire involving the dried product, Cold Fire®** fire suppressing agent is preferred as the extinguishing medium. If Cold Fire® is not available, use water spray as the extinguishing medium. Take efforts to ensure that these agents reach the base of the smoldering or fire. Parker-LORD Corporation will not be responsible for personal injuries, property damage or any other damages arising from the accumulation (buildup, cleaning/removal or any related smoldering or fire) resulting from the use of this product. Refer to the Chemlok® Safe Handling Guide for additional information. **NOTE: Parker-LORD Corporation has determined Cold Fire® fire suppressing agent to be effective in extinguishing fires involving dried Chemlok® adhesives. Parker-LORD does not recommend any particular equipment or system for use in delivering or applying Cold Fire® products. Customer is responsible for determining that Cold Fire® products and any delivery equipment or system is appropriate and effective for customer's specific needs. During a fire, irritating and/or toxic gases and particulate may be generated by thermal decomposition or combustion.SPECIAL PROTECTIVE EQUIPMENT AND PRECAUTIONS FOR FIRE-FIGHTERS: Wear full firefighting protective clothing, including self-contained breathing apparatus (SCBA). If water is used, fog nozzles are preferable.PERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES: Avoid breathing vapors. Avoid contact. Use appropriate respiratory protection for large spills or spills in confined area.ENVIRONMENTAL PRECAUTIONS: Do not contaminate bodies of water, waterways, or ditches, with chemical or used container.METHODS AND MATERIALS FOR CONTAINMENT AND CLEANUP: Notify appropriate authorities if necessary. Contain and remove with inert absorbent material. Avoid contact. Keep non-essential personnel away from spill area. Before attempting cleanup, refer to hazard caution information in other sections of the SDS form.HANDLING: Keep closure tight and container upright to prevent leakage. Avoid skin and eye contact. Wash thoroughly after handling. Do not handle until all safety precautions have been read and understood. Empty containers should not be re-used. Use with adequate ventilation.STORAGE: Store only in well-ventilated areas. Keep from freezing. Keep container closed when not in use.INCOMPATIBILITY: Strong acids, bases, and strong oxidizers.Engineering controls: Sufficient ventilation in pattern and volume should be provided in order to maintain air contaminant levels below recommended exposure limits.PERSONAL PROTECTION MEASURES/EQUIPMENT:RESPIRATORY PROTECTION: Use a NIOSH approved chemical/mechanical filter respirator designed to remove a combination of particulates and organic vapor if occupational limits are exceeded. For emergencysituations, confined space use, or other conditions where exposure limits may be greatly exceeded, use an approved air-supplied respirator. For respirator use observe OSHA regulations (29CFR 1910.134) or use in accordance with applicable laws and regulations of your country or particular locality.SKIN PROTECTION: Use neoprene, nitrile, or rubber gloves to prevent skin contact.EYE PROTECTION: Use safety eyewear including safety glasses with side shields and chemical goggles where splashing may occur.OTHER PROTECTIVE EQUIPMENT: Remove and wash contaminated clothing before reuse.HYGIENIC PRACTICES: Wash hands before eating, smoking, or using toilet facility. Do not smoke in any chemical handling or storage area. Food or beverages should not be consumed anywhere this product is handled or stored. Wash thoroughly after handling.Typical values, not to be used for specification purposes.ODOR: Odorless VAPOR PRESSURE: N.D.APPEARANCE: Green/Black VAPOR DENSITY: Heavier than Air PHYSICAL STATE: Liquid LOWER EXPLOSIVE LIMIT: Not ApplicableUPPER EXPLOSIVE LIMIT: Not ApplicableFLASH POINT:≥ 201 °F, 93 °CSetaflash Closed CupBOILING RANGE: 100 °C EVAPORATION RATE: Slower than n-butyl-acetate AUTOIGNITION TEMPERATURE:N.D.DENSITY: 1.18 g/cm3 (9.83 lb/gal) DECOMPOSITION TEMPERATURE:N.D. VISCOSITY, DYNAMIC: N.D.ODOR THRESHOLD: N.D.VISCOSITY, KINEMATIC: N.D.SOLUBILITY IN H2O: Soluble VOLATILE BY WEIGHT: 52.14 %pH: 6.0VOLATILE BY VOLUME: 61.54 %FREEZE POINT: N.D. VOC CALCULATED: 0.02 lb/gal, 3 g/l COEFFICIENT OF WATER/OILN.D.DISTRIBUTION:LEGEND: N.A. - Not Applicable, N.E. - Not Established, N.D. - Not DeterminedHAZARDOUS POLYMERIZATION: Hazardous polymerization will not occur under normal conditions.STABILITY: Product is stable under normal storage conditions.CONDITIONS TO AVOID: High temperatures.; For dried product issues, refer to Section 5 of the (M)SDS. INCOMPATIBILITY: Strong acids, bases, and strong oxidizers.HAZARDOUS DECOMPOSITION PRODUCTS: Decomposition due to high temperatures or a fire causes the formation of irritating and/or toxic gases, organic vapors or fumes., May contain CO, CO2, oxides of nitrogen, oxides of sulfur, halogenated by-products, Metal oxidesEXPOSURE PATH: Refer to section 2 of this SDS.SYMPTOMS:Refer to section 2 of this SDS.TOXICITY MEASURES:Germ cell mutagenicity: No classification proposedCarcinogenicity: Category 2 - Suspected of causing cancer.Components contributing to classification: Curative.Reproductive toxicity: No classification proposedPERSISTENCE AND DEGRADABILITY:Not determined for this product.BIOACCUMULATIVE: Not determined for this product.MOBILITY IN SOIL: Not determined for this product.OTHER ADVERSE EFFECTS: Not determined for this product.DISPOSAL METHOD: Disposal should be done in accordance with Federal (40CFR Part 261), state and local environmental control regulations. If waste is determined to be hazardous, use licensed hazardous waste transporter and disposal facility. Waste streams, including the dried adhesive residue, resulting from the use of this product should be tested for RCRA characteristics, including ignitability, to determine any applicable waste classifications.US DOT RoadProper Shipping Name: Environmentally hazardous substances, liquid, n.o.s.Hazard Class: 9SECONDARY HAZARD: NoneUN/NA Number: 3082Packing Group: IIIEmergency Response Guide Number: 171For US DOT non-bulk road shipments this material may be classified as NOT REGULATED. For the mostaccurate shipping information, refer to your transportation/compliance department regarding changes inpackage size, mode of shipment or other regulatory descriptors.IATA CargoPROPER SHIPPING NAME: Environmentally hazardous substance, liquid, n.o.s.Hazard Class: 9HAZARD CLASS: NoneUN NUMBER: 3082PACKING GROUP: IIIEMS: 9LIMDGPROPER SHIPPING NAME: Environmentally hazardous substance, liquid, n.o.s.Hazard Class: 9HAZARD CLASS: NoneUN NUMBER: 3082PACKING GROUP: IIIEMS: F-AThe listed transportation classification applies to non-bulk shipments. It does not address regulatory variations due to changes in package size, mode of shipment or other regulatory descriptors. For the most accurate shipping information, refer to your transportation/compliance department.U.S. FEDERAL REGULATIONS: AS FOLLOWS:SARA SECTION 313This product contains the following substances subject to the reporting requirements of Section 313 of Title III of the Superfund Amendment and Reauthorization Act of 1986 and 40 CFR part 372.:Chemical Name CAS Number Weight % Less ThanZinc compound PROPRIETARY10.0%TOXIC SUBSTANCES CONTROL ACT:INVENTORY STATUSThe chemical substances in this product are on the active TSCA Section 8 Inventory or exempt.EXPORT NOTIFICATIONThis product contains the following chemical substances subject to the reporting requirements of TSCA 12(B) if exported from the United States:NoneUnder HazCom 2012 it is optional to continue using the HMIS rating system. It is important to ensure employees have been trained to recognize the different numeric ratings associated with the HazCom 2012 and HMIS schemes.HMIS RATINGS - HEALTH: 2* FLAMMABILITY: 1 PHYSICAL HAZARD: 0* - Indicates a chronic hazard; see Section 2Revision: Company LogoEffective Date: 06/30/2021The information contained herein is, to the best of our knowledge and belief, accurate. However, since the conditions of handling and use are beyond our control, we make no guarantee of results, and assume no liability for damages incurred by use of this material. It is the responsibility of the user to comply with all applicable federal, state and local laws and regulations.。
Chemlok 8008水溶性合金基础数据表说明书
Chemlok® 8008 Primer Technical Data SheetChemlok® 8008 primer is a water-based primer that bonds elastomers to metals and other substrates when usedin combination with Chemlok water-based covercoat adhesives. It is composed of a mixture of dispersed mineral fillers, organic compounds, resins and polymer latices in an aqueous medium.Features and Benefits:Environmentally Preferred – provides low VOC and HAP for reduced emissions, allowing for safer work environment and regulatory compliance.Versatile – functions as an effective primer for many materials such as steel, phosphated steel, nylon, aluminum and brass.Environmentally Resistant – preferred water-based Chemlok primer for glycol resistance; provides excellent resistance to water, salt spray, oil and heat.Durable – maintains excellent metal adhesion under flexing and high-stress conditions.Excellent Appearance – provides a smooth coating for use by dip or spray applications. The green color affords good contrast with water-based covercoat adhesives and prepared substrates.Easy to Use – easily redispersed within 5 to 15 minutes of stirring; imparts little or no settling; ready to use directly out of the container without dilution.Application:Surface Preparation – Thoroughly clean metal surfaces prior to application. Remove protective oils, cutting oils and greases by solvent degreasing or alkaline cleaning. Remove rust, scale or oxide coatings by suitable chemical or mechanical cleaning methods.For further detailed information on surface preparationof specific substrates, refer to Chemlok Adhesives application guide.Mixing – Thoroughly mix primer before using to disperse any soft settling which may have occurred during storage. Do not shake. To prevent foaming, mechanical mixing should not exceed 30 rpm. The addition of anti-foaming agents is not recommended.In most cases, dilution is not required. Deionized wateris suggested if dilution is necessary. Add water gradually while stirring either by hand or by using another low-shear mixing method.Applying – Preheat substrates to 60-65°C (140-150°F) prior to spray application of primer. This heat and spray method prevents runs and sags and gives a dry coating ready for covercoat application. Use contaminant-freeair for spraying. All spray equipment, including tanks, fixtures, pressure pots, hoses, guns and nozzles, should be stainless steel or plastic.Dry film thickness of Chemlok 8008 primer should be5.1-10.2 micron (0.2-0.4 mil).Chemlok 8008 Primer — Technical Data SheetParker LordEngineered Materials Group 111 LORD DriveCary, NC 27511-7923USAphone +1 877 275 /EPMValues stated in this document represent typical values as not all tests are run on each lot of material produced. For formalized product specifications for specific product end uses, contact the Customer Support Center.Information provided herein is based upon tests believed to be reliable. In as much as Parker Lord has no control over the manner in which others may use this information, it does not guarantee the results to be obtained. In addition, Parker Lord does not guarantee the performance of the product or the results obtained from the use of the product or this information where the product has been repackaged by any third party, including but not limited to any product end-user. Nor does the company make any express or implied warranty of merchantability or fitness for a particular purpose concerning the effects or results of such use.WARNING — USER RESPONSIBILITY . FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE.This document and other information from Parker-Hannifin Corporation, its subsidiaries and authorized distributors provide product or system options for further investigation by users having technical expertise.The user, through its own analysis and testing, is solely responsible for making the final selection of the system and components and assuring that all performance, endurance, maintenance, safety and warning requirements of theapplication are met. The user must analyze all aspects of the application, follow applicable industry standards, and follow the information concerning the product in the current product catalog and in any other materials provided from Parker or its subsidiaries or authorized distributors.To the extent that Parker or its subsidiaries or authorized distributors provide component or system options based upon data or specifications provided by the user, the user is responsible for determining that such data and specifications are suitable and sufficient for all applications and reasonably foreseeable uses of the components or systems.©2023 Parker Hannifin - All Rights ReservedInformation and specifications subject to change without notice and without liability therefor. Trademarks used herein are the property of their respective owners.OD DS4043 05/23 Rev.4Drying – If no preheat is employed, parts will dry in 30-60 minutes at room temperature. Allow coated parts to dry at least 60 minutes at room temperature before applying Chemlok water-based covercoat adhesive.Cleanup – Use soap and water to remove wet primer. Dried primer is not water-soluble and must be removed with a ketone-type solvent.Shelf Life/Storage:Shelf life is six months from date of shipment whenstored by the recipient in a well ventilated area at 21-27°C (70-80°F) in original, unopened container. Do not freeze product. Storage below 4°C (40°F) may be detrimental to the primer’s properties.Cautionary Information:Before using this or any Parker Lord product, refer to the Safety Data Sheet (SDS) and label for safe use and handling instructions.For industrial/commercial use only. Must be applied by trained personnel only. Not to be used in household applications. Not for consumer use.。
Chemlok 粘合剂安全操作指南技术数据表说明书
Chemlok® Adhesives Safe Handling Guide Technical Data SheetChemlok® adhesives have been used in the rubber industry for over 60 years. By adhering to established safe handling techniques, these products have been utilized without posing a hazard to people or property. This document serves as a guide to make customers aware of potential hazards, and suggests procedures to eliminate them in the workplace. Refer to the product Safety Data Sheet (SDS) and label before using any Chemlok product.Types of Products:There are three basic types of Chemlok adhesives:• S olvent-based Adhesives• W ater-based Adhesives• 100% Solids AdhesivesPotential hazards and suggested safe handling procedures for each type of Chemlok adhesive are addressed in this document.Solvent-based AdhesivesMany of these products are flammable due the typeof solvents that they contain. Solvents used in these products include aromatics, acetates, alcohols, ketones, chlorinated solvents, or a combination of these types. Use safety procedures appropriate for flammable liquids when handling products containing any of these solvents. Typically, chlorinated solvents are not flammable; however, chlorinated solvents, when used in conjunction with flammable solvents, can result in a flammable mixture. Water-based AdhesivesWater-based adhesive systems are formulated primarily in water. However, some may contain small amounts of water miscible organic solvents such as glycol ethers based on ethylene or propylene glycol. Although most water-based Chemlok adhesives are not flammable in the wet state, some specialty elastomer adhesives contain alcohol, which may cause the adhesive system to be flammable. Refer to the product SDS to identify the flash point and flammability of individual water-based adhesives.100% Solids AdhesivesMost 100% solids adhesives are either epoxy or polyurethane based resins. Fire or explosion hazardsare minimal with these products; however, they are combustible and will burn.Safe Handling Procedures: Flammability• U se Chemlok products in well-ventilated areas.• S pray adhesives only in an OSHA-approved spray booth.• F or flammable adhesives, use of explosion-proofelectrical outlets, wiring, motors and exhaust fans is required by OSHA, the National Electric Code (NEC), and insurance underwriters.• F lammable solvent-based adhesives should be stored in metal containers. Metal containers are more conductive and reduce the possibility of static and heat buildup.• G round and bond metal containers when transferring flammable liquid solvents and adhesives.• I solate containers from heat, electrical equipment, sparks, friction, open flame and other sources of ignition.• K eep containers tightly closed when not in use.• C lean up spills immediately according to instructions in Section 6 (Accidental Release) of the product SDS.• I n the event of a fire with a Chemlok product, use fire-fighting measures outlined in Section 5 (Fire Fighting Measures) of the product SDS.• E nsure that a qualified engineer or technician supervises the design, construction, and operation of any carbon adsorption systems that are used in venting Chemlok products. Some types of Chemlok products contain chemicals, such as ketones, that may react withthe carbon surface causing severe exotherms or temperature excursions.Spill Cleanup• K eep non-essential personnel a safe distance away from the spill area.• F or flammable Chemlok products, remove all sourcesof ignition (flame, heat, electrical, static or frictional sparks).• A void breathing vapors – use appropriate respiratory protection, if necessary.• A void contact – use appropriate personal protective equipment.•C ontain and remove the spilled product with inert absorbent material (and non-sparking tools for flammable Chemlok products).• N otify appropriate authorities, in accordance with applicable regulatory requirements, as necessary.• B efore attempting cleanup, refer to Section 6 (Accidental Release) of the product SDS.Personal Health and SafetyBecause of the variation of hazardous ingredients in Chemlok products and the resulting differing potential effects of personal exposure to workers, it is essentialto refer to the SDS and label for the specific product to ensure that it is stored, handled and used safely and that appropriate controls and personal protective equipment are utilized.• U se in well ventilated area. Avoid breathing vapors and spray mist.• A void skin and eye contact.• W ear approved respirators when occupational limits are exceeded.• U se safety eyewear including safety glasses with side shields and chemical goggles where splashing may occur.• W ear appropriate gloves.• U se disposable or impervious clothing. Remove and wash when contaminated.• W ash thoroughly before eating, smoking, or using toilet facility.• I f first aid measures are needed for ingestion, inhalation, eye contact or skin contact, refer to Section 4 (First Aid Measures) of the product SDS.Application/Spray Equipment• E nsure extinguishers are near application equipment and readily accessible.• F ixtures with excessive film buildup or film buildup that falls off a part or gets into the oven can increase the risk of smoldering/fires.• A utomated application equipment (chain-on-edge) and associated ovens should have safety interlocks that shut down the oven or stop the line in the event of a fire.• E lectric, steam coil or natural gas enclosed box-type ovens are preferred. IR ovens have an increased potential for causing Chemlok products to smolder or ignite.• U se flame retardant, heavyweight paper to line all floor areas in immediate application area to prevent buildup on floor. Dispose of dirty paper under proper regulatory guidelines.• U se disposable/peelable spray booth coating to protect all spray booth walls, etc. Sprinkler heads in the spray application areas should be covered according to local fire code to protect from excess spray debris building up on them. This covering will prevent excessive buildup, allowing proper functioning during a fire.• W arning: Due to the combustible nature of the dried film of Chemlok products and the potential for smolderingor fire, the accumulation and buildup of the dried filmon spray booth walls and floors, spindles, fixtures and other surfaces should be avoided, and any buildup should be removed. Refer to Cleaning section for more information. In the event of smoldering or a fire involving the dried product, Cold Fire® fire suppressing agent* is preferred as the extinguishing medium. If Cold Fire is not available, use water spray as the extinguishing medium. Take efforts to ensure that these agents reach the base of the smoldering or fire. LORD Corporation will notbe responsible for personal injuries, property damage or any other damages arising from the accumulation (buildup), cleaning/removal, or any related smoldering or fire resulting from the use of Chemlok products. Waste Disposal ProceduresGuidelines established here are for waste streams generated from the use of Chemlok products. Disposal should be done in accordance with national and local environmental waste control regulations. The waste stream should be evaluated for hazardous characteristics. If waste is determined to be hazardous, properly dispose per local requirements.• W aste containing residual solvent should be treated as a flammable hazard.• W aste streams comprised of dried Chemlok adhesive residue should be treated as ignitable solids per the Globally Harmonized System of classification.• L iquid or solid waste known to contain toxic contaminants such as persistent, bioaccumulative toxins should be treated a hazardous.*Note: Parker LORD has determined Cold Fire fire suppressing agentto be effective in extinguishing fires involving dried Chemlok adhesives. Parker LORD does not recommend any particular equipment or system for use in delivering or applying Cold Fire products. Customer is responsible for determining that Cold Fire products and any delivery equipment or system is appropriate and effective for customer’s specific needs.Parker LORDEngineered Materials Group 111 LORD DriveCary, NC 27511-7923USAphone +1 877 ASK LORD (275 5673)Values stated in this document represent typical values as not all tests are run on each lot of material produced. For formalized product specifications for specific product end uses, contact the Customer Support Center.Information provided herein is based upon tests believed to be reliable. In as much as Parker LORD has no control over the manner in which others may use this information, it does not guarantee the results to be obtained. In addition, Parker LORD does not guarantee the performance of the product or the results obtained from the use of the product or this information where the product has been repackaged by any third party, including but not limited to any product end-user. Nor does the company make any express or implied warranty of merchantability or fitness for a particular purpose concerning the effects or results of such use.WARNING — USER RESPONSIBILITY . FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE.This document and other information from Parker-Hannifin Corporation, its subsidiaries and authorized distributors provide product or system options for further investigation by users having technical expertise.The user, through its own analysis and testing, is solely responsible for making the final selection of the system and components and assuring that all performance, endurance, maintenance, safety and warning requirements of theapplication are met. The user must analyze all aspects of the application, follow applicable industry standards, and follow the information concerning the product in the current product catalog and in any other materials provided from Parker or its subsidiaries or authorized distributors.To the extent that Parker or its subsidiaries or authorized distributors provide component or system options based upon data or specifications provided by the user, the user is responsible for determining that such data and specifications are suitable and sufficient for all applications and reasonably foreseeable uses of the components or systems.©2022 Parker Hannifin - All Rights ReservedInformation and specifications subject to change without notice and without liability therefor. Trademarks used herein are the property of their respective owners.OD DS3100 03/22 Rev.8Housekeeping• P revention of dry film buildup is key for safe handling. Daily or weekly inspection of application equipment, including oven tunnels and associated equipment, is recommended. Dry Chemlok adhesive residue becomes more flammable as the thickness of the film increases. • R emove dried adhesive around any mixing shafts where heat could build up and cause smoldering/fire.• A void excessive buildup of dried Chemlok products on floors and other surfaces. CleaningIt is always recommended to avoid the buildup of dried Chemlok adhesive films. However, if a film buildup has to be cleaned, the following precautions should be followed. • N on-sparking brass brush or plastic scrapers can be used for cleaning. Caution should be exercised as brush/scraper can also generate sufficient heat from friction to initiate smoldering/fire.• T here are a variety of debris removal methods. Consult with your Parker LORD representative to determine suitable methods for debris removal from application equipment.• M ake sure that some sort of water reservoir is available to continually wet down the surfaces being cleaned.This keeps temperatures down and reduces the effect of frictional heat buildup during cleaning.• F or larger debris clean-ups, explosion-proof vacuums are suggested.Remember – There are no short cuts to Safety!Cautionary Information:Before using this or any Parker LORD product, refer to the Safety Data Sheet (SDS) and label for safe use and handling instructions.For industrial/commercial use only. Must be applied by trained personnel only. Not to be used in household applications. Not for consumer use.。
Chemlok 黏贴剂选择指南说明书
8560S, 8210*, 8216* 8600
8116**
ST YRENE BUTADIENE (SBR)
6253, 6150, 6411*, 6108*
PRIMERS
PRODUCT
14 4 205 205LH 207 207LH 298 459M 459T 459X 7701 8006 8007 Blue 8008 8009 8009B A P -131 A P -13 4 E P 5 0 8 0 -11
DESCRIPTION
Solvent-borne primer with UV tracer General purpose primer/nitrile adhesive Low-HAP Chemlok 205 Heat-resistant primer Low-HAP Chemlok 207 High performance primer Primer for TPE/TPO/EPDM with UV tracer Primer for TPE/TPO/EPDM Primer for TPE/TPO/EPDM Solvent-based surface treatment Environmentally resistant, water-based primer General purpose primer Water-based primer Water-based primer Water-based primer Solvent-borne primer Solvent-borne primer Clear Chemlok 205 primer/nitrile adhesive
TY-PLY BN
6150
AP-133
ETHYLENE ACRYLIC & EPICHLOROHYDRIN
CHEMLOK 220X 产品安全数据表说明书
USA SAFETY DATA SHEET1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATIONProduct name: CHEMLOK 220X Product Use/Class:AdhesiveLORD Corporation 111 LORD DriveCary, NC 27511-7923 USATelephone: 814 868-3180Non-Transportation Emergency: 814 763-2345 Chemtrec 24 Hr Transportation Emergency No.800 424-9300 (Outside Continental U.S. 703 527-3887)EFFECTIVE DATE: 02/12/20202. HAZARDS IDENTIFICATIONGHS CLASSIFICATION:Flammable liquids Category 3Skin corrosion/irritation Category 2Serious eye damage/eye irritation Category 2A Skin sensitization Category 1 Carcinogenicity Category 1B Reproductive toxicity Category 2Specific target organ systemic toxicity (single exposure) Category 3Specific target organ systemic toxicity (single exposure) Category 2 blood systemSpecific target organ systemic toxicity (single exposure) Category 1 Central nervous system, Kidney, Liver, Respiratory systemSpecific target organ systemic toxicity (repeated exposure) Category 1 Nervous system, Respiratory system Specific target organ systemic toxicity (repeated exposure) Category 2 Ears, blood system Hazardous to the aquatic environment - acute hazard Category 2 Hazardous to the aquatic environment - chronic hazardCategory 2GHS LABEL ELEMENTS:Symbol(s)Signal WordD ANGERHazard StatementsFlammable liquid and vapor. Causes skin irritation.Causes serious eye irritation.May cause an allergic skin reaction. May cause cancer.Suspected of damaging fertility or the unborn child. May cause harm to breast-fed children. May cause respiratory irritation. May cause drowsiness or dizziness.May cause damage to organs.(blood system)Causes damage to organs.(Central nervous system, Kidney, Liver, Respiratory system)Causes damage to organs through prolonged or repeated exposure.(Nervous system, Respiratory system) May cause damage to organs through prolonged or repeated exposure.(Ears, blood system)Toxic to aquatic life.Toxic to aquatic life with long lasting effects.Precautionary StatementsPreventionKeep away from heat/sparks/open flames/hot surfaces. - No smoking.Ground/Bond container and receiving equipment.Use explosion-proof electrical/ventilating/lighting equipment.Use only non-sparking tools.Take precautionary measures against static discharge.Obtain special instructions before use.Do not handle until all safety precautions have been read and understood.Wear protective gloves/protective clothing/eye protection/face protection.Use personal protective equipment as required.Do not breathe dust/fume/gas/mist/vapors/spray.Wash thoroughly after handling.Do not eat, drink or smoke when using this product.Use only outdoors or in a well-ventilated area.Contaminated work clothing should not be allowed out of the workplace.Avoid release to the environment.ResponseIn case of fire: refer to section 5 of SDS for extinguishing media.Call a POISON CENTER or doctor/physician if you feel unwell.IF exposed: Call a POISON CENTER or doctor/physician.Specific treatment (see supplemental first aid instructions on this label).IF INHALED: Remove to fresh air and keep at rest in a position comfortable for breathing.IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower.If skin irritation or rash occurs: Get medical advice/attention.IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do.Continue rinsing.Collect spillage.StorageStore in a well-ventilated place. Keep cool.Store in a well-ventilated place. Keep container tightly closed.Store locked up.Disposal:Dispose of contents/container in accordance with waste/disposal laws and regulations of your country or particular locality.Other Hazards:This product contains component(s) which have the following warnings; however based on the GHS classification criteria of your country or locale, the product mixture may be outside the respective category(s).Acute: Vapor harmful; may affect the brain or nervous system causing dizziness, headache or nausea. Possibleirritation of the respiratory system can occur causing a variety of symptoms such as dryness of the throat, tightness of the chest, and shortness of breath. In elevated-temperature applications, product may release vapors that may produce cyanosis in the absence of sufficient ventilation or adequate respiratory protection. May cause central nervous system depression characterized by the following progressive steps: headache, dizziness, staggering gait, confusion,unconsciousness or coma.May be harmful if swallowed. Ingestion is not an expected route of entry in industrial or commercial uses.Chronic: May affect the gastrointestinal system. The nitrogen substituted aromatic in this product gave positiveresults for mutagenicity in an Ames Assay study while two other mutagenicity studies proved negative. Overexposure to lead in this product can damage the nervous, urinary, gastrointestinal, blood, blood-forming, and reproductivesystems. Lead and lead compounds have been classified by IARC as probable human carcinogens (Group 2A), and by NTP as reasonably anticipated human carcinogens. Ethylbenzene has been classified by IARC as a possiblehuman carcinogen (Group 2B) and reported by NTP to show clear evidence for carcinogenicity in animals. IARC has designated carbon black as Group 2B - inadequate evidence for carcinogenicity in humans, but sufficient evidence in experimental animals. In 2006 IARC reaffirmed its 1995 finding that there is "inadequate evidence" from humanconducted investigations has shown no causative link between carbon black exposure and the risk of malignant or non-malignant respiratory disease in humans. IARC and NTP have determined that there is sufficient evidence for carcinogenicity of tetrachloroethylene to experimental animals and limited evidence in humans.3. COMPOSITION/INFORMATION ON INGREDIENTSChemical Name CAS Number RangeXylene1330-20-755 - 60%Ethyl benzene100-41-410 - 15%Carbon black1333-86-4 1 - 5%Nitrogen substituted aromatic PROPRIETARY 1 - 5%Lead oxide phosphonate12141-20-7 1 - 5%Toluene108-88-30.1 - 0.9%Tetrachloroethylene127-18-40.1 - 0.9%Any "PROPRIETARY" component(s) in the above table is considered trade secret, thus the specific chemical and its exact concentration is being withheld.4. FIRST AID MEASURESFIRST AID - EYE CONTACT: Flush eyes immediately with large amount of water for at least 15 minutes holding eyelids open while flushing. Get prompt medical attention.FIRST AID - SKIN CONTACT: Flush contaminated skin with large amounts of water while removing contaminated clothing. Wash affected skin areas with soap and water. Get medical attention if symptoms occur.FIRST AID - INHALATION: Move person to fresh air. Restore and support continued breathing. If breathing is difficult, give oxygen. Get immediate medical attention.FIRST AID - INGESTION: If swallowed, do not induce vomiting. Call a physician or poison control center immediately for further instructions. Never give anything by mouth if victim is rapidly losing consciousness, unconscious or convulsing.5. FIRE-FIGHTING MEASURESSUITABLE EXTINGUISHING MEDIA: Carbon Dioxide, Dry Chemical, Foam, Water FogUNSUITABLE EXTINGUISHING MEDIA: Not determined for this product.SPECIFIC HAZARDS POSSIBLY ARISING FROM THE CHEMICAL: Flammable liquid and vapor. Keep containers tightly closed. Isolate from heat, electrical equipment, sparks, open flame, and other sources of ignition. Closed containers may rupture when exposed to extreme heat. Use water spray to keep fire exposed containers cool. During a fire, irritating and/or toxic gases and particulate may be generated by thermal decomposition or combustion.SPECIAL PROTECTIVE EQUIPMENT AND PRECAUTIONS FOR FIRE-FIGHTERS: Wear full firefighting protective clothing, including self-contained breathing apparatus (SCBA). Water spray may be ineffective. If water is used, fog nozzles are preferable.6. ACCIDENTAL RELEASE MEASURESPERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES: Remove all sources of ignition (flame, hot surfaces, and electrical, static or frictional sparks). Avoid contact. Avoid breathing vapors. Use self-contained breathing equipment.ENVIRONMENTAL PRECAUTIONS: Do not contaminate bodies of water, waterways, or ditches, with chemical or used container.METHODS AND MATERIALS FOR CONTAINMENT AND CLEANUP: Keep non-essential personnel a safe distance away from the spill area. Notify appropriate authorities if necessary. Avoid contact. Before attempting cleanup, referto hazard caution information in other sections of the SDS form. Contain and remove with inert absorbent material and non-sparking tools.7. HANDLING AND STORAGEHANDLING: Keep closure tight and container upright to prevent leakage. Ground and bond containers when transferring material. Avoid skin and eye contact. Wash thoroughly after handling. Avoid breathing of vapor or spray mists. Do not handle until all safety precautions have been read and understood. Empty containers should not be re-used. Avoid breathing sanding dust from this product. Avoid using pressurizable equipment which has aluminum or zinc parts; this product contains chlorinated solvents. Use with adequate ventilation. Because empty containers may retain product residue and flammable vapors, keep away from heat, sparks and flame; do not cut, puncture or weld on or near the empty container. This product contains inorganic lead; potential lead exposure exists when applying or sanding this product. Use of this product should comply with the OSHA Lead Standard (29 CFR 1910.1025) or where applicable the OSHA Construction Standard for lead (29 CFR 1926.62). Do not smoke where this product is used or stored.STORAGE: Do not store or use near heat, sparks, or open flame. Store only in well-ventilated areas. Do not puncture, drag, or slide container. Keep container closed when not in use. Refer to OSHA 29CFR Part 1910.106 "Flammable and Combustible Liquids" for specific storage requirements.INCOMPATIBILITY: Strong oxidizers, acids, bases, water.; Aluminum, zinc, caustics, halogens.8. EXPOSURE CONTROLS/PERSONAL PROTECTIONCOMPONENT EXPOSURE LIMITChemical Name ACGIH TLV-TWA ACGIH TLV-STELOSHA PEL-TWAOSHA PEL-CEILINGSkinXylene100 ppm150 ppm435 mg/m3100 ppmN.E.N.A.Ethyl benzene20 ppm N.E.435 mg/m3100 ppmN.E.N.A.Carbon black 3 mg/m3N.E. 3.5 mg/m3 N.E.N.A.Nitrogen substituted aromatic N.E.N.E.N.E. N.E.N.A.Lead oxide phosphonate0.05 mg/m3N.E.0.05 mg/m3 N.E.N.A.Toluene20 ppm N.E.200 ppm 300 ppmN.A.Tetrachloroethylene25 ppm100 ppm100 ppm 100 ppmN.A.N.A. - Not Applicable, N.E. - Not Established, S - Skin DesignationEngineering controls: Sufficient ventilation in pattern and volume should be provided in order to maintain air contaminant levels below recommended exposure limits. Caution: Solvent vapors are heavier than air and collect in lower levels of the work area. Sufficient ventilation (using explosion-proof equipment) should be provided to prevent flammable vapor/air mixtures from accumulating.PERSONAL PROTECTION MEASURES/EQUIPMENT:RESPIRATORY PROTECTION: Use a NIOSH approved chemical/mechanical filter respirator designed to remove a combination of particulates and organic vapor if occupational limits are exceeded. For emergencysituations, confined space use, or other conditions where exposure limits may be greatly exceeded, use an approved air-supplied respirator. For respirator use observe OSHA regulations (29CFR 1910.134) or use in accordance with applicable laws and regulations of your country or particular locality.SKIN PROTECTION: Use neoprene, nitrile, or rubber gloves to prevent skin contact.EYE PROTECTION: Use safety eyewear including safety glasses with side shields and chemical goggles where splashing may occur.OTHER PROTECTIVE EQUIPMENT: Use disposable or impervious clothing if work clothing contamination is likely. Remove and wash contaminated clothing before reuse.HYGIENIC PRACTICES: Wash hands before eating, smoking, or using toilet facility. Do not smoke in anychemical handling or storage area. Food or beverages should not be consumed anywhere this product is handled or stored. Wash thoroughly after handling.9. PHYSICAL AND CHEMICAL PROPERTIESTypical values, not to be used for specification purposes.ODOR: Solvent VAPOR PRESSURE: N.D.APPEARANCE: Black VAPOR DENSITY: Heavier than Air PHYSICAL STATE: Liquid LOWER EXPLOSIVE LIMIT: 1 %(V)UPPER EXPLOSIVE LIMIT: 7 %(V)FLASH POINT: 81 °F, 27 °C SetaflashClosed CupBOILING RANGE: 136 - 141 °C EVAPORATION RATE: Slower than n-butyl-acetate AUTOIGNITION TEMPERATURE:N.D.DENSITY: 0.98 g/cm3 - 8.15 lb/gal DECOMPOSITION TEMPERATURE:N.D. VISCOSITY, DYNAMIC: ≥80 mPa.s @ 25 °C ODOR THRESHOLD: N.D.VISCOSITY, KINEMATIC: ≥82 mm2/s @ 25 °CSOLUBILITY IN H2O: Insoluble VOLATILE BY WEIGHT: 75.21 %pH: N.A.VOLATILE BY VOLUME: 85.70 %FREEZE POINT: N.D. VOC CALCULATED: 6.02 lb/gal, 722 g/lN.D.COEFFICIENT OF WATER/OILDISTRIBUTION:LEGEND: N.A. - Not Applicable, N.E. - Not Established, N.D. - Not Determined10. STABILITY AND REACTIVITYHAZARDOUS POLYMERIZATION: Hazardous polymerization will not occur under normal conditions. STABILITY: Product is stable under normal storage conditions.CONDITIONS TO AVOID: High temperatures. Sources of ignition.; Aluminum or galvanized parts in a closed system. INCOMPATIBILITY: Strong oxidizers, acids, bases, water.; Aluminum, zinc, caustics, halogens.HAZARDOUS DECOMPOSITION PRODUCTS: Carbon dioxide, carbon monoxide, chlorine, hydrogen chloride, Phosgene, Lead fume, Oxides of nitrogen11. TOXICOLOGICAL INFORMATIONEXPOSURE PATH: Refer to section 2 of this SDS.SYMPTOMS:Refer to section 2 of this SDS.TOXICITY MEASURES:Chemical Name LD50/LC50Xylene Oral LD50: Rat3,500 mg/kgDermal LD50: Rabbit> 4,350 mg/kgInhalation LC50: Rat29.08 mg/l/4 hEthyl benzene Oral LD50: Rat3,500 mg/kgDermal LD50: Rabbit15,400 mg/kgInhalation LC50: Rat17.4 mg/l/4 hCarbon black Oral LD50: Rat> 15,400 mg/kgDermal LD50: Rabbit> 3 g/kgGHS LC50 (vapour): Acute toxicity point estimate55 mg/lNitrogen substituted aromatic Oral LD50: rat1,100 mg/kgLead oxide phosphonate GHS LC50 (vapour): Acute toxicity point estimate55 mg/lDermal LD50: Rabbit12,000 mg/kgInhalation LC50: Rat12.5 mg/l/4 hTetrachloroethylene Oral LD50: Rat2,629 mg/kgInhalation LC50: Rat27.8 mg/l/4 hGerm cell mutagenicity: No classification proposedCarcinogenicity: Category 1B - May cause cancer.Components contributing to classification: Ethyl benzene. Lead oxide phosphonate. Tetrachloroethylene.Reproductive toxicity: Category 2 - Suspected of damaging fertility or the unborn child. May cause harm to breast-fed children.Components contributing to classification: Xylene. Ethyl benzene. Lead oxide phosphonate. Toluene.Tetrachloroethylene.12. ECOLOGICAL INFORMATIONECOTOXICITY:Chemical Name EcotoxicityXylene Fish: Pimephales promelas13.4 mg/l96 h flow-throughOncorhynchus mykiss2.661 - 4.093 mg/l96 h StaticOncorhynchus mykiss13.5 - 17.3 mg/l96 hLepomis macrochirus13.1 - 16.5 mg/l96 h flow-throughLepomis macrochirus19 mg/l96 hLepomis macrochirus7.711 - 9.591 mg/l96 h StaticPimephales promelas23.53 - 29.97 mg/l96 h StaticCyprinus carpio780 mg/l96 h semi-staticCyprinus carpio> 780 mg/l96 hPoecilia reticulata30.26 - 40.75 mg/l96 h StaticInvertebrates: water flea3.82 mg/l48 hGammarus lacustris0.6 mg/l48 hEthyl benzene Fish: Oncorhynchus mykiss11.0 - 18.0 mg/l96 h StaticOncorhynchus mykiss4.2 mg/l96 h semi-staticPimephales promelas7.55 - 11 mg/l96 h flow-throughLepomis macrochirus32 mg/l96 h StaticPimephales promelas9.1 - 15.6 mg/l96 h StaticPoecilia reticulata9.6 mg/l96 h StaticInvertebrates: Daphnia magna1.8 - 2.4 mg/l48 hPlants: Pseudokirchneriella subcapitata4.6 mg/l72 hPseudokirchneriella subcapitata> 438 mg/l96 hPseudokirchneriella subcapitata2.6 - 11.3 mg/l72 h StaticPseudokirchneriella subcapitata1.7 - 7.6 mg/l96 h StaticCarbon black N.D.Nitrogen substituted aromatic N.D.Lead oxide phosphonate N.D.Toluene Fish: Pimephales promelas15.22 - 19.05 mg/l96 h flow-throughPimephales promelas12.6 mg/l96 h StaticOncorhynchus mykiss5.89 - 7.81 mg/l96 h flow-throughOncorhynchus mykiss14.1 - 17.16 mg/l96 h StaticOncorhynchus mykiss5.8 mg/l96 h semi-staticLepomis macrochirus11.0 - 15.0 mg/l96 h StaticOryzias latipes54 mg/l96 h StaticPoecilia reticulata28.2 mg/l96 h semi-staticPoecilia reticulata50.87 - 70.34 mg/l96 h StaticInvertebrates: Daphnia magna5.46 - 9.83 mg/l48 h StaticDaphnia magna11.5 mg/l48 hPlants: Pseudokirchneriella subcapitata> 433 mg/l96 hPseudokirchneriella subcapitata12.5 mg/l72 h StaticTetrachloroethylene Fish: Pimephales promelas12.4 - 14.4 mg/l96 h flow-throughPimephales promelas8.6 - 13.5 mg/l96 h StaticLepomis macrochirus11.0 - 15.0 mg/l96 h StaticOncorhynchus mykiss4.73 - 5.27 mg/l96 h flow-throughInvertebrates: Daphnia magna6.1 - 9.0 mg/l48 h StaticPlants: Pseudokirchneriella subcapitata> 500 mg/l96 hPERSISTENCE AND DEGRADABILITY:Not determined for this product.BIOACCUMULATIVE: Not determined for this product.MOBILITY IN SOIL: Not determined for this product.OTHER ADVERSE EFFECTS: Not determined for this product.13. DISPOSAL CONSIDERATIONSDISPOSAL METHOD: Disposal should be done in accordance with Federal (40CFR Part 261), state and local environmental control regulations. If waste is determined to be hazardous, use licensed hazardous waste transporter and disposal facility.14. TRANSPORT INFORMATIONUS DOT RoadProper Shipping Name: AdhesivesHazard Class: 3SECONDARY HAZARD: NoneUN/NA Number: 1133Packing Group: IIIEmergency Response Guide Number: 128IATA CargoPROPER SHIPPING NAME: AdhesivesHazard Class: 3HAZARD CLASS: NoneUN NUMBER: 1133PACKING GROUP: IIIEMS: 3LIMDGPROPER SHIPPING NAME: AdhesivesHazard Class: 3HAZARD CLASS: NoneUN NUMBER: 1133PACKING GROUP: IIIEMS: F-EThe listed transportation classification applies to non-bulk shipments. It does not address regulatory variations due to changes in package size, mode of shipment or other regulatory descriptors. For the most accurate shipping information, refer to your transportation/compliance department.15. REGULATORY INFORMATIONU.S. FEDERAL REGULATIONS: AS FOLLOWS:SARA SECTION 313This product contains the following substances subject to the reporting requirements of Section 313 of Title III of the Superfund Amendment and Reauthorization Act of 1986 and 40 CFR part 372.:Chemical Name CAS Number Weight % Less ThanXylene1330-20-760.0%Ethyl benzene100-41-415.0%Lead oxide phosphonate12141-20-7 5.0%Toluene108-88-30.9%Tetrachloroethylene127-18-40.9%TOXIC SUBSTANCES CONTROL ACT:INVENTORY STATUSThe chemical substances in this product are on the TSCA Section 8 Inventory.EXPORT NOTIFICATIONThis product contains the following chemical substances subject to the reporting requirements of TSCA 12(B) if exported from the United States:None16. OTHER INFORMATIONUnder HazCom 2012 it is optional to continue using the HMIS rating system. It is important to ensure employees have been trained to recognize the different numeric ratings associated with the HazCom 2012 and HMIS schemes.HMIS RATINGS - HEALTH: 2* FLAMMABILITY: 3 PHYSICAL HAZARD: 0* - Indicates a chronic hazard; see Section 2Revision: Section 2, Section 3, Section 8, Section 11, Section 12Effective Date: 02/12/2020DISCLAIMERThe information contained herein is, to the best of our knowledge and belief, accurate. However, since the conditions of handling and use are beyond our control, we make no guarantee of results, and assume no liability for damages incurred by use of this material. It is the responsibility of the user to comply with all applicable federal, state and local laws and regulations.。
CHEMLOK 459X 产品说明书
USA SAFETY DATA SHEET300000002744 1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATIONProduct name:CHEMLOK 459XProduct Use/Class:Primer for AdhesiveLORD Corporation 111 LORD Drive Cary, NC 27511-7923 USATelephone: 814 868-3180Non-Transportation Emergency: 814 763-2345 Chemtrec 24 Hr Transportation Emergency No. 800 424-9300 (Outside Continental U.S. 703 527-3887)EFFECTIVE DATE : 11/23/20202. HAZARDS IDENTIFICATIONGHS CLASSIFICATION :Flammable liquids Category 3 Skin corrosion/irritation Category 2 Serious eye damage/eye irritation Category 2A Carcinogenicity Category 2 Reproductive toxicity Category 2Specific target organ systemic toxicity (single exposure) Category 1 Central nervous system, Kidney, Liver, Respiratory systemSpecific target organ systemic toxicity (single exposure) Category 3 Specific target organ systemic toxicity (repeated exposure) Category 1 Nervous system, Respiratory system Specific target organ systemic toxicity (repeated exposure) Category 2 Ears Aspiration hazard Category 1Hazardous to the aquatic environment - acute hazard Category 2GHS LABEL ELEMENTS : Symbol(s)Signal WordD ANGERHazard StatementsFlammable liquid and vapor. Causes skin irritation.Causes serious eye irritation. Suspected of causing cancer.Suspected of damaging fertility or the unborn child. May cause harm to breast -fed children. Causes damage to organs.(Central nervous system, Kidney, Liver, Respiratory system ) May cause drowsiness or dizziness. May cause respiratory irritation.Causes damage to organs through prolonged or repeated exposure.(Nervous system, Respiratory system ) May cause damage to organs through prolonged or repeated exposure.(Ears ) May be fatal if swallowed and enters airways. Toxic to aquatic life.Precautionary StatementsPrevention- No smoking.Keep away from heat/sparks/open flames/hot surfaces.Ground/Bond container and receiving equipment.Use explosion-proof electrical/venti lating/lighting equipment.Use only non-sparking tools.Take precautionary measures against static discharge.Obtain special instructions before use.Do not handle until all safety precautions have been read and understood.e clothing/eye protection/face protection.Wear protective gloves/protectivUse personal protective equipment as required.Do not breathe dust/fume/gas/mist/vapors/spray.Wash thoroughly after handling.Do not eat, drink or smoke when using this product.Use only outdoors or in a well-ven tilated area.Avoid release to the environment.ResponseIn case of fire: refer to section 5 of SDS for extinguishing media.Call a POISON CENTER or doctor/physician if you feel unwell.IF exposed: Call a POISON CENTER or doctor/physician.Specific treatm ent (see supplemental first aid instructions on this label).IF INHALED: Remove to fresh air and keep at rest in a position comfortable for breathing..IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/showerIf skin irritation occurs: Get medical advice/attention.IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do.Continue rinsing.IF SWALLOWED: Immediately call a POISON CENTER or doctor/physician.Do NOT induce vomiting.StorageStore in a well-ventilated place. Keep cool.Store in a well-ventilated place. Keep container tightly closed.Store locked up.Disposal:Dispose of contents/container in accordance with waste/disposal laws and regulations of your country or particular locality.Other Hazards:This product contains component(s) which have the following warnings; however based on the GHS classification criteria of your country or locale, the product mixture may be outside the respective category(s).Acute: Vapor harmful; may affect the brain or nervous system causing dizziness, headache or nausea. Possibleng a variety of symptoms such as dryness of the throat, tightness of irritation of the respiratory system can occur causithe chest, and shortness of breath. May cause central nervous system depression characterized by the followingiousness or coma. This product contains a progressive steps: headache, dizziness, staggering gait, confusion, unconscresidual amount of a chemical substance that may cause an allergic skin and/or respiratory reaction.May be harmful if swallowed. Ingestion is not an expected route of entry in industrial or commercial uses.-forming organs. Prolonged or Chronic: May affect the gastrointestinal system. May affect the blood and bloodrepeated contact may result in dermatitis. Ethylbenzene has been classified by IARC as a possible human carcinogenw clear evidence for carcinogenicity in animals.(Group 2B) and reported by NTP to showithheld.FIRST AID - EYE CONTACT: Flush eyes immediately with large amount of water for at least 15 minutes holding eyelids open while flushing. Get prompt medical attention.FIRST AID - SKIN CONTACT: Flush contaminated skin with large amounts of water while removing contaminated clothing. Wash affected skin areas with soap and water. Get medical attention if symptoms occur.FIRST AID - INHALATION: Move person to fresh air. Restore and support continued breathing. If breathing is difficult,ion.give oxygen. Get immediate medical attentFIRST AID - INGESTION: If swallowed, do not induce vomiting. Call a physician or poison control center immediatelyfor further instructions. Never give anything by mouth if victim is rapidly losing consciousness, unconscious or convulsing.SUITABLE EXTINGUISHI NG MEDIA: Carbon Dioxide, Dry Chemical, Foam, Water FogUNSUITABLE EXTINGUIS HING MEDIA: Not determined for this product.SPECIFIC HAZARDS POSSIBLY ARISING FROM T HE CHEMICAL: Flammable liquid and vapor. Keep containers tightly closed. Isolate from heat, electrical equipment, sparks, open flame, and other sources of ignition. Closed containersners cool. During a fire, irritatingmay rupture when exposed to extreme heat. Use water spray to keep fire exposed contaiand/or toxic gases and particulate may be generated by thermal decomposition or combustion.SPECIAL PROTECTIVE E QUIPMENT AND PRECAUT IONS FOR FIRE-FIGHTE RS: Wear full firefightingprotective clothing, including self-contained breathing apparatus (SCBA).If water isWater spray may be ineffective.used, fog nozzles are preferable.PERSONAL PRECAUTIONS, PROTECTIV E EQUIPMENT AND EMER GENCY PROCEDURES: Remove all.sources of ignition (flame, hot surfaces, and electrical, static or frictional sparks). Avoid contact. Avoid breathing vapors Use self-contained breathing equipment.ENVIRONMENTAL PREC AUTIONS: Do not contaminate bodies of water, waterways, or ditches, with chemical or used container.METHODS AND MATERIAL S FOR CONTAINMENT AN D CLEANUP: Keep non-essential personnel a safeorities if necessary. Avoid contact. Before attempting cleanup, refer distance away from the spill area. Notify appropriate auth-to hazard caution information in other sections of the SDS form. Contain and remove with inert absorbent material and non sparking tools.HANDLING: Keep closure tight and container upright to prevent leakage. Ground and bond containers when transferring material. Avoid skin and eye contact. Wash thoroughly after handling. Avoid breathing of vapor or spray mists. Do not-used. Use withhandle until all safety precautions have been read and understood. Empty containers should not be readequate ventilation. Because empty containers may retain product residue and flammable vapors, keep away from heat, puncture or weld on or near the empty container. Do not smoke where this product is used or sparks and flame; do not cut,stored.-ventilated areas. Do not puncture, drag, STORAGE: Do not store or use near heat, sparks, or open flame. Store only in welltainer closed when not in use. Refer to OSHA 29CFR Part 1910.106 "Flammable andor slide container. Keep conCombustible Liquids" for specific storage requirements.INCOMPATIBILITY: Strong oxidizers, acids, bases, water.Engineering controls: Sufficient ventilation in pattern and volume should be provided in order to maintain airposure limits. Caution: Solvent vapors are heavier than air and collect in lower contaminant levels below recommended ex-proof equipment) should be provided to prevent flammable levels of the work area. Sufficient ventilation (using explosionvapor/air mixtures from accumulating.PERSONAL PROTECTION MEASURES/EQU IPMENT:RESPIRATORY PROTECTION: Use a NIOSH approved chemical/mechanical filter respirator designed toremove a combination of particulates and organic vapor if occupational limits are exceeded. For emergencysituations, confined sp ace use, or other conditions where exposure limits may be greatly exceeded, use an approved air-supplied respirator. For respirator use observe OSHA regulations (29CFR 1910.134) or use in accordance witharticular locality.applicable laws and regulations of your country or pSKIN PROTECTION: Use neoprene, nitrile, or rubber gloves to prevent skin contact.EYE PROTECTION: Use safety eyewear including safety glasses with side shields and chemical goggles where splashing may occur.OTHER PROTECTIVE EQUIPMENT: Use disposable or impervious clothing if work clothing contamination is likely. Remove and wash contaminated clothing before reuse.HYGIENIC PRACTICES: Wash hands before eating, smoking, or using toilet facility. Do not smoke in anyche mical handling or storage area. Food or beverages should not be consumed anywhere this product is handled or stored. Wash thoroughly after handling.Typical values, not to be used for specification purposes.ODOR: Solvent VAPOR PRESSURE:N.D.APPEARANCE: Clear VAPOR DENSITY:Heavier than AirPHYSICAL STATE:Liquid LOWER EXPLOSIVE LIMIT: 1 %(V)UPPER EXPLOSIVE LIMIT:7 %(V)FLASH POINT: 81 °F, 27 °C SetaflashClosed CupBOILING RANGE: 136 - 141 °C EVAPORATION RATE:Not Applicable AUTOIGNITION TEMPERA TURE:N.D.DENSITY:0.85 g/cm3 (7.08 lb/gal)DECOMPOSITION TEMPER ATURE:N.D. VISCOSITY, DYNAMIC:≥10 mPa.s @ 25 °C ODOR THRESHOLD:N.D.VISCOSITY, KINEMATIC: ≥12 mm2/s@ 25 °CSOLUBILITY IN H2O:Insoluble VOLATILE BY WEIGHT:96.50 %pH: N.A.VOLATILE BY VOLUME:97.18 %FREEZE POINT:N.D. VOC CALCULATED: 6.83 lb/gal, 819 g/lN.D. METHOD 24: 7.03 lb/gallon COEFFICIENT OF WATER/OILDISTRIBUTION:LEGEND: N.A. - Not Applicable, N.E. - Not Established, N.D. - Not DeterminedHAZARDOUS POLYMERIZATION: Hazardous polymerization will not occur under normal conditions.STABILITY: Product is stable under normal storage conditions.CONDITIONS TO AVOID: High temperatures. Sources of ignition.INCOMPATIBILITY: Strong oxidizers, acids, bases, water.HAZARDOUS DECOMPOSITION PRODUCTS: Carbon dioxide, carbon monoxide, chlorine, hydrogen chloride, PhosgeneEXPOSURE PATH: Refer to section 2 of this SDS.SYMPTOMS:Refer to section 2 of this SDS.TOXICITY MEASURES:Germ cell mutagenicity: No classification proposedCarcinogenicity: Category 2- Suspected of causing cancer.Components contributing to classification:Ethyl benzene.-Reproductive toxicity: Category 2- Suspected of damaging fertility or the unborn child. May cause harm to breast fed children.Components contributing to classification:Xylene. Ethyl benzene. Toluene.PERSISTENCE AND DEGRADABILITY:Not determined for this product.BIOACCUMULATIVE: Not determined for this product.MOBILITY IN SOIL: Not determined for this product.OTHER ADVERSE EFFECTS: Not determined for this product.DISPOSAL METHOD: Disposal should be done in accordance with Federal (40CFR Part 261), state and localIf waste is determined to be hazardous, use licensed hazardous waste transporter and environmental control regulations.disposal facility.US DOT RoadProper Shipping Name: AdhesivesHazard Class: 3SECONDARY HAZARD: NoneUN/NA Number: 1133Packing Group: IIIEmergency Response Guide Number: 128IATA CargoPROPER SHIPPING NAME: AdhesivesHazard Class: 3HAZARD CLASS: NoneUN NUMBER: 1133PACKING GROUP: IIIEMS: 3LIMDGPROPER SHIPPING NAME: AdhesivesHazard Class: 3HAZARD CLASS: NoneUN NUMBER: 1133PACKING GROUP: IIIEMS: F-E-bulk shipments. It does not address regulatory variations due toThe listed transportation classification applies to nonchanges in package size, mode of shipment or other regulatory descriptors. For the most accurate shipping information, refer to your t ransportation/compliance department.U.S. FEDERAL REGULATIONS: AS FOLLOWS:SARA SECTION 313This product contains the following substances subject to the reporting requirements of Section 313 of Title III of the:Superfund Amendment and Reauthorization Act of 1986 and 40 CFR part 372.Chemical Name CAS Number Weight % Less ThanXylene1330-20-780.0%Ethyl benzene100-41-420.0%TOXIC SUBSTANCES CONTROL ACT:INVENTORY STATUSThe chemical substances in this product are on the TSCA Section 8 Inventory.EXPORT NOTIFICATIONThis product contains the following chemical substances subject to the reporting requirements of TSCA 12(B) if:exported from the United StatesNoneUnder HazCom 2012 it is optional to continue using the HMIS rating system. It is important to ensure employees have been trained to recognize the different numeric ratings associated with the HazCom 2012 and HMIS schemes.HMIS RATINGS - HEALTH: 2* FLAMMABILITY: 3 PHYSICAL HAZARD: 0* - Indicates a chronic hazard; see Section 2Revision: Section 1Effective Date: 11/23/2020The information contained herein is, to the best of our knowledge and belief, accurate. However, since the conditions of handling and use are beyond our control, we make no guarantee of results, and assume no liability for damages incurred byuse of this material. It is the responsibility of the user to comply with all applicable federal, state and local laws and regulations.。
LORD Chemlok 8800 一批水性胶合剂说明说明书
DescriptionLORD Chemlok ® 8800 adhesive is a one-coat, aqueous adhesive used for bonding silicone rubber, EPDM, HNBR, XHNBR, AFLAS, VAMAC and other peroxide-cured materials.With good resistance to hot oils, hot water and other fl uids, Chemlok 8800 adhesive is suitable for use in the manufacture of gaskets, seals and NVH components.Features and Benefi tsConvenient – requires only a single coat for most appli-cations, reducing labor, inventory and shipping costs.Environmentally Friendly – uses water for dilution; provides reduced VOC emissions.Versatile – bonds a wide range of compounds to many rigid substrates, such as zinc phosphatized steel, copper, nylon and aluminum.Environmentally Resistant – provides good resistance to high temperature fl uid environments.Chemlok ®8800 AdhesiveApplicationSurface Preparation – Thoroughly clean metal surfaces prior to adhesive application. Remove protective oils, cutting oils and greases by solvent degreasing oralkaline cleaning. Remove rust, scale or oxide coatings by suitable chemical or mechanical cleaning methods.• Chemical CleaningChemical treatments are readily adapted to auto-mated metal treatment and adhesive application lines. Chemical treatments are also used on metal parts that would be distorted by blast cleaning or where tight tolerances must be maintained. Phos-phatizing is a commonly used chemical treatment for steel, while conversion coatings are commonly used for aluminum.• Mechanical CleaningGrit blasting is the most widely used method ofmechanical cleaning. However machining, grinding or wire brushing can be used. Use steel grit to blast clean steel, cast iron and other ferrous metals. Use aluminum oxide, sand or other nonferrous grit to blast clean stainless steel, aluminum, brass, zinc and other nonferrous metals.Typical Properties*AppearanceBeige Liquid Viscosity, cps @ 25°C (77°F)5 -100Brookfi eld LVT Spindle 2, 30 rpmDensitykg/m 31114 -1174(lb/gal) (9.3 - 9.8)Solids Content by Weight, % 28 - 32Flash Point (Seta), °C (°F) >93 (>200)Solvents Deionized Water*Data is typical and not to be used for specifi cation purposes.LORD provides valuable expertise in adhesives and coatings, vibration and motion control, and magnetically responsive technologies. Ourpeople work in collaboration with our customers to help them increase the value of their products. Innovative and responsive in an ever-changing marketplace, we are focused on providing solutions for our customers worldwide ... Ask Us How.LORD Corporation World Headquarters 111 Lord DriveCary, NC 27511-7923 USACustomer Support Center (in United States & Canada)+1 877 ASK LORD (275 5673)For a listing of our worldwide locations, visit .Values stated in this technical data sheet represent typical values as not all tests are run on each lot of material produced. For formalized product specifi cations for specifi c product end uses, contact the Customer Support rmation provided herein is based upon tests believed to be reliable. In as much as LORD Corporation has no control over the manner in which others may use this information, it does not guarantee the results to be obtained. In addition, LORD Corporation does not guarantee the perfor-mance of the product or the results obtained from the use of the product or this information where the product has been repackaged by any third party, including but not limited to any product end-user. Nor does the company make any express or implied warranty of merchantability or fi tness for a particular purpose concerning the effects or results of such use.Chemlok and “Ask Us How” are trademarks of LORD Corporation or one of its subsidiaries.©2013 LORD Corporation OD DS4144 (Rev.0 6/13)For further detailed information on surface preparation of specifi c substrates, refer to Chemlok Adhesives appli-cation guide. Handle clean metal surfaces with clean gloves to avoid contamination with skin oils.Mixing – Stir Chemlok 8800 adhesive for 5-10 minutes. Do not shake.Chemlok 8800 adhesive is used full strength for dip applications. For spray application, dilute as needed using deionized water.Applying – Apply Chemlok 8800 adhesive by spray or dip methods. For optimum adhesion, the dry fi lm thickness of Chemlok 8800 adhesive should be 7.6-17.8 micron (0.3-0.7 mil).• SprayingApply adhesive to parts that have been preheated to 60-65°C (140-150°F).• DippingApply adhesive at room temperature.Drying/Curing – Use of heat forced air is recommended to thoroughly dry coated parts.Chemlok 8800 adhesive cures and bonds during the rubber vulcanization process. Wear clean gloves when handling coated parts and keep coated parts covered to prevent airborne materials from contaminating the surface.Cleanup – Use soap and water to remove wet adhesive. Remove dried adhesive with solvents such as acetone, MEK or alcohols.Shelf Life/StorageShelf life is 90 days from date of shipment when stored refrigerated in original, unopened container. Do not freeze product.Cautionary InformationBefore using this or any LORD product, refer to the Mate-rial Safety Data Sheet (MSDS) and label for safe use and handling instructions.For industrial/commercial use only. Must be applied by trained personnel only. Not to be used in household applications. Not for consumer use.。
LORD Corporation 产品说明书 - CHEMLOK 8560S-1
USA SAFETY DATA SHEET1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATIONProduct name: CHEMLOK 8560S-1Product Use/Class: Aqueous AdhesiveLORD Corporation111 LORD DriveCary, NC 27511-7923 USATelephone: 814 868-3180Non-Transportation Emergency: 814 763-2345 Chemtrec 24 Hr Transportation Emergency No.800 424-9300 (Outside Continental U.S. 703 527-3887)EFFECTIVE DATE: 12/20/20212. HAZARDS IDENTIFICATIONGHS CLASSIFICATION:Serious eye damage/eye irritation Category 2B Skin sensitization Category 1A Carcinogenicity Category 2Specific target organ systemic toxicity (single exposure) Category 2 blood system Specific target organ systemic toxicity (repeated exposure) Category 2 blood system Hazardous to the aquatic environment - acute hazard Category 2 Hazardous to the aquatic environment - chronic hazard Category 2GHS LABEL ELEMENTS:Symbol(s)Signal WordW ARNINGHazard StatementsCauses eye irritation.May cause an allergic skin reaction. Suspected of causing cancer.May cause damage to organs.(blood system)May cause damage to organs through prolonged or repeated exposure.(blood system) Toxic to aquatic life.Toxic to aquatic life with long lasting effects.Precautionary Statements PreventionObtain special instructions before use.Do not handle until all safety precautions have been read and understood. Wear protective gloves.Use personal protective equipment as required. Do not breathe dust/fume/gas/mist/vapors/spray. Wash thoroughly after handling.Do not eat, drink or smoke when using this product.Contaminated work clothing should not be allowed out of the workplace. Avoid release to the environment.Product: CHEMLOK 8560S-1, Effective Date: 12/20/2021ResponseGet medical advice/attention if you feel unwell.Call a POISON CENTER or doctor/physician if exposed or you feel unwell.Specific treatment (see supplemental first aid instructions on this label).IF ON SKIN: Wash with plenty of soap and water.If skin irritation or rash occurs: Get medical advice/attention.IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do.Continue rinsing.If eye irritation persists: Get medical advice/attention.Wash contaminated clothing before reuse.Collect spillage.StorageStore locked up.Disposal:Dispose of contents/container in accordance with waste/disposal laws and regulations of your country or particular locality.Other Hazards:This product contains component(s) which have the following warnings; however based on the GHS classification criteria of your country or locale, the product mixture may be outside the respective category(s).Acute: May cause mild skin irritation. In elevated-temperature applications, product may release vapors that may produce cyanosis in the absence of sufficient ventilation or adequate respiratory protection. 4,4'-Diphenylmethane bis-maleimide is harmful by inhalation. Avoid breathing sanding dust from this product. May be harmful ifswallowed. Ingestion is not an expected route of entry in industrial or commercial uses.Chronic: Prolonged or repeated contact may result in dermatitis. The nitrogen substituted aromatic in this product gave positive results for mutagenicity in an Ames Assay study while two other mutagenicity studies proved negative.IARC has designated carbon black as Group 2B - inadequate evidence for carcinogenicity in humans, but sufficient evidence in experimental animals. In 2006 IARC reaffirmed its 1995 finding that there is "inadequate evidence"from human health studies to assess whether carbon black causes cancer in humans. Further, epidemiologicalevidence from well-conducted investigations has shown no causative link between carbon black exposure and the risk of malignant or non-malignant respiratory disease in humans. IARC has identified the proprietary curative in this product as an "animal suspected" carcinogen, Group 3, which downgrades a previous NCI report of it as an "animal positive" carcinogen.3. COMPOSITION/INFORMATION ON INGREDIENTSChemical Name CAS Number RangeNitrogen substituted aromatic PROPRIETARY15 - 20%Zinc compound PROPRIETARY 5 - 10%4,4'-Diphenylmethane bis-maleimide13676-54-5 1 - 5%Carbon black1333-86-4 1 - 5%Nonylphenol ethoxylate compound PROPRIETARY0.9 - 1%Curative PROPRIETARY0.1 - 0.9%Any "PROPRIETARY" component(s) in the above table is considered trade secret, thus the specific chemical and its exact concentration is being withheld.4. FIRST AID MEASURESFIRST AID - EYE CONTACT: Flush eyes immediately with large amount of water for at least 15 minutes holding eyelids open while flushing. Get prompt medical attention.FIRST AID - SKIN CONTACT: Flush contaminated skin with large amounts of water while removing contaminated clothing. Wash affected skin areas with soap and water. Get medical attention if symptoms occur.FIRST AID - INHALATION: Move person to fresh air. Restore and support continued breathing. If breathing is difficult, give oxygen. Get immediate medical attention.Product: CHEMLOK 8560S-1, Effective Date: 12/20/2021FIRST AID - INGESTION: If swallowed, do not induce vomiting. Call a physician or poison control center immediately for further instructions. Never give anything by mouth if victim is rapidly losing consciousness, unconscious or convulsing.5. FIRE-FIGHTING MEASURESSUITABLE EXTINGUISHING MEDIA: Carbon Dioxide, Dry Chemical, Foam, Water FogUNSUITABLE EXTINGUISHING MEDIA: Not determined for this product.SPECIFIC HAZARDS POSSIBLY ARISING FROM THE CHEMICAL: Keep containers tightly closed. Closed containers may rupture when exposed to extreme heat. Use water spray to keep fire exposed containers cool. WARNING: Due to the combustible nature of the dried film of this product and the potential for smoldering or fire, the accumulation and buildup of the dried film on spray booth walls and floors, spindles, fixtures and other surfaces should be avoided, and any buildup should be removed. Keep the dried film accumulations away from sparks, friction, impact, high heat (>235 F/>112 C) or other sources of ignition. These conditions could cause the dried film to ignite very readily and quickly, and the resulting smoldering or fire may be difficult to extinguish. During removal of accumulation/buildup of this product, take precautions to avoid heat, friction and impact during the cleaning process. Use paint stripper, brass brush, or plastic scraper for cleaning. In the event of smoldering or a fire involving the dried product, Cold Fire®** fire suppressing agent is preferred as the extinguishing medium. If Cold Fire® is not available, use water spray as the extinguishing medium. Take efforts to ensure that these agents reach the base of the smoldering or fire. Parker-LORD Corporation will not be responsible for personal injuries, property damage or any other damages arising from the accumulation (buildup, cleaning/removal or any related smoldering or fire) resulting from the use of this product. Refer to the Chemlok® Safe Handling Guide for additional information. **NOTE: Parker-LORD Corporation has determined Cold Fire® fire suppressing agent to be effective in extinguishing fires involving dried Chemlok® adhesives. Parker-LORD does not recommend any particular equipment or system for use in delivering or applying Cold Fire® products. Customer is responsible for determining that Cold Fire® products and any delivery equipment or system is appropriate and effective for customer's specific needs. During a fire, irritating and/or toxic gases and particulate may be generated by thermal decomposition or combustion. SPECIAL PROTECTIVE EQUIPMENT AND PRECAUTIONS FOR FIRE-FIGHTERS: Wear full firefighting protective clothing, including self-contained breathing apparatus (SCBA). If water is used, fog nozzles are preferable.6. ACCIDENTAL RELEASE MEASURESPERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES: Avoid breathing vapors. Avoid contact. Use appropriate respiratory protection for large spills or spills in confined area. See Section 5 for cautionary information on the dried residue of this product.ENVIRONMENTAL PRECAUTIONS: Do not contaminate bodies of water, waterways, or ditches, with chemical or used container.METHODS AND MATERIALS FOR CONTAINMENT AND CLEANUP: Notify appropriate authorities if necessary. Contain and remove with inert absorbent material. Avoid contact. Keep non-essential personnel away from spill area. Before attempting cleanup, refer to hazard caution information in other sections of this Safety Data Sheet.7. HANDLING AND STORAGEHANDLING: Keep closure tight and container upright to prevent leakage. Avoid skin and eye contact. Wash thoroughly after handling. Do not handle until all safety precautions have been read and understood. Empty containers should not be re-used. Use with adequate ventilation. See Section 5 for cautionary information on handling of the dried residue of this product. Avoid breathing sanding dust from this product.STORAGE: Store only in well-ventilated areas. Keep from freezing. Keep container closed when not in use. INCOMPATIBILITY: Strong acids, bases, and strong oxidizers.8. EXPOSURE CONTROLS/PERSONAL PROTECTIONCOMPONENT EXPOSURE LIMIT Chemical Name ACGIH TLV-TWA ACGIH TLV-STELOSHA PEL-TWAOSHA PEL-CEILINGSkinProduct: CHEMLOK 8560S-1, Effective Date: 12/20/2021Nitrogen substituted aromatic N.E.N.E.N.E. N.E. N.A. Zinc compound2 mg/m3 10 mg/m3 5 mg/m3 N.E. N.A. 4,4'-Diphenylmethane bis-maleimide N.E. N.E. N.E. N.E. N.A. Carbon black3 mg/m3 N.E. 3.5 mg/m3 N.E. N.A. Nonylphenol ethoxylate compound N.E. N.E. N.E. N.E. N.A. CurativeN.E.N.E.N.E.N.E.N.A.N.A. - Not Applicable, N.E. - Not Established, S - Skin DesignationEngineering controls: Sufficient ventilation in pattern and volume should be provided in order to maintain air contaminant levels below recommended exposure limits.PERSONAL PROTECTION MEASURES/EQUIPMENT:RESPIRATORY PROTECTION: Use a NIOSH approved chemical/mechanical filter respirator designed to remove a combination of particulates and organic vapor if occupational limits are exceeded. For emergencysituations, confined space use, or other conditions where exposure limits may be greatly exceeded, use an approved air-supplied respirator. For respirator use observe OSHA regulations (29CFR 1910.134) or use in accordance with applicable laws and regulations of your country or particular locality.SKIN PROTECTION: Use neoprene, nitrile, or rubber gloves to prevent skin contact.EYE PROTECTION: Use safety eyewear including safety glasses with side shields and chemical goggles where splashing may occur.OTHER PROTECTIVE EQUIPMENT: Remove and wash contaminated clothing before reuse.HYGIENIC PRACTICES: Wash hands before eating, smoking, or using toilet facility. Do not smoke in any chemical handling or storage area. Food or beverages should not be consumed anywhere this product is handled or stored. Wash thoroughly after handling.9. PHYSICAL AND CHEMICAL PROPERTIESTypical values, not to be used for specification purposes.ODOR:Odorless VAPOR PRESSURE:N.D.APPEARANCE: Green/BlackVAPOR DENSITY:Heavier than Air PHYSICAL STATE:Thixotropic liquid LOWER EXPLOSIVE LIMIT: Not Applicable FLASH POINT: ≥ 201 °F, 93 °C Setaflash Closed Cup UPPER EXPLOSIVE LIMIT:Not Applicable BOILING RANGE:100 °CEVAPORATION RATE: Slower than n-butyl-acetateAUTOIGNITION TEMPERATURE: N.D. DENSITY:1.2 g/cm3 (10.00 lb/gal) DECOMPOSITION TEMPERATURE:N.D. VISCOSITY, DYNAMIC: ≥50 mPa.s @ 25 °C ODOR THRESHOLD: N.D.VISCOSITY, KINEMATIC: ≥42 mm2/s @ 25 °C SOLUBILITY IN H2O:Water Dispersible VOLATILE BY WEIGHT: 56.93 % pH:6.0 VOLATILE BY VOLUME:66.72 % FREEZE POINT:N.D. VOC CALCULATED: 0.02 lb/gal , 3 g/l COEFFICIENT OF WATER/OILDISTRIBUTION:N.D.LEGEND: N.A. - Not Applicable, N.E. - Not Established, N.D. - Not Determined10. STABILITY AND REACTIVITYHAZARDOUS POLYMERIZATION: Hazardous polymerization will not occur under normal conditions.STABILITY: Product is stable under normal storage conditions.Product: CHEMLOK 8560S-1, Effective Date: 12/20/2021CONDITIONS TO AVOID: High temperatures.; For dried product issues, refer to Section 5 of the (M)SDS.; DO NOT ALLOW THIS MATERIAL TO DRY OUT. As a solid, p-benzoquinone dioxime is flammable, and it may explode if exposed to shock, friction or heat.INCOMPATIBILITY: Strong acids, bases, and strong oxidizers.HAZARDOUS DECOMPOSITION PRODUCTS: Decomposition due to high temperatures or a fire causes the formation of irritating and/or toxic gases, organic vapors or fumes., May contain CO, CO2, oxides of nitrogen, oxides of sulfur, halogenated by-products, Carbon dioxide, carbon monoxide, chlorine, hydrogen chloride, Phosgene, Metal oxides11. TOXICOLOGICAL INFORMATIONEXPOSURE PATH: Refer to section 2 of this SDS.SYMPTOMS: Refer to section 2 of this SDS.TOXICITY MEASURES:Chemical NameLD50/LC50 Nitrogen substituted aromatic Oral LD50: rat 1,100 mg/kgZinc compoundOral LD50: Rat > 5,000 mg/kg Dermal LD50: Rat > 2,000 mg/kgGHS LC50 (vapour): Acute toxicity point estimate 55 mg/l Inhalation LC50: Rat > 5,700 mg/m3 /4 h 4,4'-Diphenylmethane bis-maleimide Oral LD50: Rat > 5 g/kgDermal LD50: rat > 5,400 mg/kgGHS LC50 (dust and mist): rat 0.52 mg/l Inhalation ATE: 11 mg/l Carbon blackOral LD50: Rat > 15,400 mg/kg Dermal LD50: Rabbit > 3 g/kgGHS LC50 (vapour): Acute toxicity point estimate 55 mg/l : Nonylphenol ethoxylate compound N.D.CurativeOral LD50: Rat 464 mg/kgGHS LC50 (vapour): Acute toxicity point estimate 55 mg/l Inhalation LC50: Rat > 5 mg/l /4 hGerm cell mutagenicity: No classification proposedCarcinogenicity: Category 2 - Suspected of causing cancer. Components contributing to classification: Curative.Reproductive toxicity: No classification proposed12. ECOLOGICAL INFORMATIONECOTOXICITY:Chemical NameEcotoxicityNitrogen substituted aromatic N.D. Zinc compoundN.D.4,4'-Diphenylmethane bis-maleimide Fish: Oncorhynchus mykiss (rainbow trout) > 0.145 mg/l96 hCarbon blackN.D. Nonylphenol ethoxylate compound N.D.CurativeFish: Danio rerio (zebra fish) 24 mg/l96 h Static Invertebrates: Daphnia magna (Water flea) 3.5 mg/l48 h StaticPERSISTENCE AND DEGRADABILITY: Not determined for this product.BIOACCUMULATIVE: Not determined for this product.MOBILITY IN SOIL: Not determined for this product.OTHER ADVERSE EFFECTS: Not determined for this product.13. DISPOSAL CONSIDERATIONSDISPOSAL METHOD: Disposal should be done in accordance with Federal (40CFR Part 261), state and local environmental control regulations. If waste is determined to be hazardous, use licensed hazardous waste transporter and disposal facility. Waste streams, including the dried adhesive residue, resulting from the use of this product should be tested for RCRA characteristics, including ignitability, to determine any applicable waste classifications.14. TRANSPORT INFORMATIONUS DOT RoadProper Shipping Name: Environmentally hazardous substances, liquid, n.o.s.Hazard Class: 9SECONDARY HAZARD: NoneUN/NA Number: 3082Packing Group: IIIEmergency Response Guide Number: 171For US DOT non-bulk road shipments this material may be classified as NOT REGULATED. For the mostaccurate shipping information, refer to your transportation/compliance department regarding changes inpackage size, mode of shipment or other regulatory descriptors.IATA CargoPROPER SHIPPING NAME: Environmentally hazardous substance, liquid, n.o.s.Hazard Class: 9HAZARD CLASS: NoneUN NUMBER: 3082PACKING GROUP: IIIEMS: 9LIMDGPROPER SHIPPING NAME: Environmentally hazardous substance, liquid, n.o.s.Hazard Class: 9HAZARD CLASS: NoneUN NUMBER: 3082PACKING GROUP: IIIEMS: F-AThe listed transportation classification applies to non-bulk shipments. It does not address regulatory variations due to changes in package size, mode of shipment or other regulatory descriptors. For the most accurate shipping information, refer to your transportation/compliance department.15. REGULATORY INFORMATIONU.S. FEDERAL REGULATIONS: AS FOLLOWS:SARA SECTION 313This product contains the following substances subject to the reporting requirements of Section 313 of Title III of the Superfund Amendment and Reauthorization Act of 1986 and 40 CFR part 372.:Chemical Name CAS Number Weight % Less ThanZinc compound PROPRIETARY10.0%TOXIC SUBSTANCES CONTROL ACT:INVENTORY STATUSThe chemical substances in this product are on the active TSCA Section 8 Inventory or exempt.EXPORT NOTIFICATIONThis product contains the following chemical substances subject to the reporting requirements of TSCA 12(B) if exported from the United States:None16. OTHER INFORMATIONUnder HazCom 2012 it is optional to continue using the HMIS rating system. It is important to ensure employees have been trained to recognize the different numeric ratings associated with the HazCom 2012 and HMIS schemes.HMIS RATINGS - HEALTH: 2* FLAMMABILITY: 1 PHYSICAL HAZARD: 0* - Indicates a chronic hazard; see Section 2Revision: New GHS SDS FormatEffective Date: 12/20/2021DISCLAIMERThe information contained herein is, to the best of our knowledge and belief, accurate. However, since the conditions of handling and use are beyond our control, we make no guarantee of results, and assume no liability for damages incurred by use of this material. It is the responsibility of the user to comply with all applicable federal, state and local laws and regulations.。
CHEMLOK 6253 产品说明书
USA SAFETY DATA SHEET1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATIONProduct name:CHEMLOK 6253Product Use/Class: AdhesiveLORD Corporation111 LORD DriveCary, NC 27511-7923 USATelephone: 814 868-3180Non-Transportation Emergency: 814 763-2345Chemtrec 24 Hr Transportation Emergency No.800 424-9300 (Outside Continental U.S. 703 527-3887)EFFECTIVE DATE: 09/16/20212. HAZARDS IDENTIFICATIONGHS CLASSIFICATION:Flammable liquids Category 3Acute toxicity Inhalation - Dust and Mist Category 4 - 14.2% of the mixture consists of ingredient(s) of unknown toxicity.Skin corrosion/irritation Category 2Serious eye damage/eye irritation Category 2ACarcinogenicity Category 2Reproductive toxicity Category 2Specific target organ systemic toxicity (single exposure) Category 3Specific target organ systemic toxicity (single exposure) Category 2 blood systemSpecific target organ systemic toxicity (single exposure) Category 1 Respiratory system, Systemic toxicity, Central nervous system, Kidney, LiverSpecific target organ systemic toxicity (repeated exposure) Category 2 Ears, blood systemSpecific target organ systemic toxicity (repeated exposure) Category 1 Nervous system, Respiratory systemHazardous to the aquatic environment - acute hazard Category 2Hazardous to the aquatic environment - chronic hazard Category 2GHS LABEL ELEMENTS:Symbol(s)Signal WordD ANGERHazard StatementsFlammable liquid and vapor.Harmful if inhaled.Causes skin irritation.Causes serious eye irritation.Suspected of causing cancer.Suspected of damaging fertility or the unborn child.May cause harm to breast-fed children.May cause drowsiness or dizziness.May cause damage to organs.(blood system)Causes damage to organs.(Respiratory system, Systemic toxicity, Central nervous system, Kidney, Liver)May cause damage to organs through prolonged or repeated exposure.(Ears, blood system)Causes damage to organs through prolonged or repeated exposure.(Nervous system, Respiratory system)300001006525Toxic to aquatic life.Toxic to aquatic life with long lasting effects.Precautionary StatementsPreventionKeep away from heat/sparks/open flames/hot surfaces. - No smoking.Ground/Bond container and receiving equipment.Use explosion-proof electrical/ventilating/lighting equipment.Use only non-sparking tools.Take precautionary measures against static discharge.Obtain special instructions before use.Do not handle until all safety precautions have been read and understood.Wear protective gloves/protective clothing/eye protection/face protection.Use personal protective equipment as required.Do not breathe dust/fume/gas/mist/vapors/spray.Wash thoroughly after handling.Do not eat, drink or smoke when using this product.Use only outdoors or in a well-ventilated area.Avoid release to the environment.ResponseIn case of fire: refer to section 5 of SDS for extinguishing media.Call a POISON CENTER or doctor/physician if you feel unwell.IF exposed: Call a POISON CENTER or doctor/physician.Specific treatment (see supplemental first aid instructions on this label).IF INHALED: Remove to fresh air and keep at rest in a position comfortable for breathing.IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower.If skin irritation occurs: Get medical advice/attention.IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do.Continue rinsing.Collect spillage.StorageStore in a well-ventilated place. Keep cool.Store in a well-ventilated place. Keep container tightly closed.Store locked up.Disposal:Dispose of contents/container in accordance with waste/disposal laws and regulations of your country or particular locality.Other Hazards:This product contains component(s) which have the following warnings; however based on the GHS classification criteria of your country or locale, the product mixture may be outside the respective category(s).Acute: Vapor harmful; may affect the brain or nervous system causing dizziness, headache or nausea. May cause central nervous system depression characterized by the following progressive steps: headache, dizziness, staggering gait, confusion, unconsciousness or coma. Possible irritation of the respiratory system can occur causing a variety of symptoms such as dryness of the throat, tightness of the chest, and shortness of breath. The imide in this product is a respiratory hazard. Inhalation of product vapors, fumes or particulates during heating should be avoided. In elevated-temperature applications, product may release vapors that may produce cyanosis in the absence of sufficientventilation or adequate respiratory protection. This product contains a residual amount of a chemical substance that may cause an allergic skin and/or respiratory reaction.May be harmful if swallowed. Ingestion is not an expected route of entry in industrial or commercial uses.Chronic: May affect the gastrointestinal system. May affect the blood and blood-forming organs. Prolonged orrepeated contact may result in dermatitis. Ethylbenzene has been classified by IARC as a possible human carcinogen (Group 2B) and reported by NTP to show clear evidence for carcinogenicity in animals. IARC has designated carbon black as Group 2B - inadequate evidence for carcinogenicity in humans, but sufficient evidence in experimentalanimals. In 2006 IARC reaffirmed its 1995 finding that there is "inadequate evidence" from human health studies to assess whether carbon black causes cancer in humans. Further, epidemiological evidence from well-conductedinvestigations has shown no causative link between carbon black exposure and the risk of malignant or non-malignant respiratory disease in humans. The nitrogen substituted aromatic in this product gave positive results for mutagenicity in an Ames Assay study while two other mutagenicity studies proved negative.withheld.FIRST AID - EYE CONTACT: Flush eyes immediately with large amount of water for at least 15 minutes holding eyelids open while flushing. Get prompt medical attention.FIRST AID - SKIN CONTACT: Flush contaminated skin with large amounts of water while removing contaminated clothing. Wash affected skin areas with soap and water. Get medical attention if symptoms occur.FIRST AID - INHALATION: Move person to fresh air. Restore and support continued breathing. If breathing is difficult, give oxygen. Get immediate medical attention.FIRST AID - INGESTION: If swallowed, do not induce vomiting. Call a physician or poison control center immediately for further instructions. Never give anything by mouth if victim is rapidly losing consciousness, unconscious or convulsing.SUITABLE EXTINGUISHING MEDIA: Carbon Dioxide, Dry Chemical, Foam, Water FogUNSUITABLE EXTINGUISHING MEDIA: Not determined for this product.SPECIFIC HAZARDS POSSIBLY ARISING FROM THE CHEMICAL: Flammable liquid and vapor. Keep containers tightly closed. Isolate from heat, electrical equipment, sparks, open flame, and other sources of ignition. Closed containers may rupture when exposed to extreme heat. Use water spray to keep fire exposed containers cool. During a fire, irritating and/or toxic gases and particulate may be generated by thermal decomposition or combustion. WARNING: Due to the combustible nature of the dried film of this product and the potential for fire, accumulation/buildup of the dried film on spray booth walls and floors, spindles, fixtures, and other surfaces should be avoided. Keep dried film accumulation away from sparks, friction, high heat (>235 F/>112C) or other sources of ignition. If it becomes necessary to removeaccumulation/buildup of this product, take precautions to avoid heat/friction/sparks during the cleaning process. Use paint stripper, brass brush, or plastic scraper for cleaning. In the event of a fire involving the dried product, use water as the extinguishing agent, ensuring that it reaches the base of the fire. Parker-LORD Corporation will not be responsible for personal injuries or property damages arising from the accumulation/buildup or cleaning/removal of the dried prouct. Refer to the Chemlok® Safe Handling Guide for additional information.SPECIAL PROTECTIVE EQUIPMENT AND PRECAUTIONS FOR FIRE-FIGHTERS: Wear full firefighting protective clothing, including self-contained breathing apparatus (SCBA). Water spray may be ineffective. If water is used, fog nozzles are preferable.PERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES: Remove all sources of ignition (flame, hot surfaces, and electrical, static or frictional sparks). Avoid contact. Avoid breathing vapors. Use self-contained breathing equipment. See Section 5 for cautionary information on the dried residue of this product.ENVIRONMENTAL PRECAUTIONS: Do not contaminate bodies of water, waterways, or ditches, with chemical or used container.METHODS AND MATERIALS FOR CONTAINMENT AND CLEANUP: Keep non-essential personnel a safe distance away from the spill area. Notify appropriate authorities if necessary. Avoid contact. Before attempting cleanup, refer to hazard caution information in other sections of this Safety Data Sheet. Contain and remove with inert absorbent material and non-sparking tools.HANDLING: Keep closure tight and container upright to prevent leakage. Ground and bond containers when transferring material. Avoid skin and eye contact. Wash thoroughly after handling. Avoid breathing of vapor or spray mists. Do not handle until all safety precautions have been read and understood. Empty containers should not be re-used. Use with adequate ventilation. Because empty containers may retain product residue and flammable vapors, keep away from heat, sparks and flame; do not cut, puncture or weld on or near the empty container. Do not smoke where this product is used or stored. See Section 5 for cautionary information on handling of the dried residue of this product.STORAGE: Do not store or use near heat, sparks, or open flame. Store only in well-ventilated areas. Do not puncture, drag, or slide container. Keep container closed when not in use. Refer to OSHA 29CFR Part 1910.106 "Flammable and Combustible Liquids" for specific storage requirements.INCOMPATIBILITY: Strong oxidizers, acids, bases, water.Engineering controls: Sufficient ventilation in pattern and volume should be provided in order to maintain air contaminant levels below recommended exposure limits. Caution: Solvent vapors are heavier than air and collect in lower levels of the work area. Sufficient ventilation (using explosion-proof equipment) should be provided to prevent flammable vapor/air mixtures from accumulating.PERSONAL PROTECTION MEASURES/EQUIPMENT:RESPIRATORY PROTECTION: Use a NIOSH approved chemical/mechanical filter respirator designed toremove a combination of particulates and organic vapor if occupational limits are exceeded. For emergencysituations, confined space use, or other conditions where exposure limits may be greatly exceeded, use an approved air-supplied respirator. For respirator use observe OSHA regulations (29CFR 1910.134) or use in accordance with applicable laws and regulations of your country or particular locality.SKIN PROTECTION: Use neoprene, nitrile, or rubber gloves to prevent skin contact.EYE PROTECTION: Use safety eyewear including safety glasses with side shields and chemical goggles where splashing may occur.OTHER PROTECTIVE EQUIPMENT: Use disposable or impervious clothing if work clothing contamination is likely. Remove and wash contaminated clothing before reuse.HYGIENIC PRACTICES: Wash hands before eating, smoking, or using toilet facility. Do not smoke in any chemical handling or storage area. Food or beverages should not be consumed anywhere this product is handled or stored. Wash thoroughly after handling.Typical values, not to be used for specification purposes.ODOR: Solvent VAPOR PRESSURE: N.D.APPEARANCE: Black VAPOR DENSITY: Heavier than Air PHYSICAL STATE: Liquid LOWER EXPLOSIVE LIMIT: 1 %(V)UPPER EXPLOSIVE LIMIT: 7 %(V)FLASH POINT: 81 °F, 26 °C SetaflashClosed CupBOILING RANGE: 136 - 141 °C EVAPORATION RATE: Slower than n-butyl-acetate AUTOIGNITION TEMPERATURE:N.D.DENSITY: 1.0281 g/cm3 (8.58lb/gal) DECOMPOSITION TEMPERATURE:N.D. VISCOSITY, DYNAMIC: ≥525 mPa.s @ 25 °C ODOR THRESHOLD: N.D.VISCOSITY, KINEMATIC: ≥243 mm2/s @ 25 °CSOLUBILITY IN H2O: Insoluble VOLATILE BY WEIGHT: 69.75 %pH: N.A.VOLATILE BY VOLUME: 82.51 %FREEZE POINT: N.D. VOC CALCULATED: 5.8 lb/gal, 695 g/lN.D.COEFFICIENT OF WATER/OILDISTRIBUTION:LEGEND: N.A. - Not Applicable, N.E. - Not Established, N.D. - Not DeterminedHAZARDOUS POLYMERIZATION: Hazardous polymerization will not occur under normal conditions.STABILITY: Product is stable under normal storage conditions.CONDITIONS TO AVOID: High temperatures. Sources of ignition.INCOMPATIBILITY: Strong oxidizers, acids, bases, water.HAZARDOUS DECOMPOSITION PRODUCTS: Carbon dioxide, carbon monoxide, chlorine, hydrogen chloride, Phosgene, Oxides of nitrogen, Metal oxidesEXPOSURE PATH: Refer to section 2 of this SDS.SYMPTOMS:Refer to section 2 of this SDS.TOXICITY MEASURES:Germ cell mutagenicity: No classification proposedCarcinogenicity: Category 2 - Suspected of causing cancer.Components contributing to classification: Ethyl benzene.Reproductive toxicity: Category 2 - Suspected of damaging fertility or the unborn child. May cause harm to breast-fed children.Components contributing to classification: Xylene. Ethyl benzene. Toluene.PERSISTENCE AND DEGRADABILITY:Not determined for this product.BIOACCUMULATIVE: Not determined for this product.MOBILITY IN SOIL: Not determined for this product.OTHER ADVERSE EFFECTS: Not determined for this product.DISPOSAL METHOD: Disposal should be done in accordance with Federal (40CFR Part 261), state and local environmental control regulations. If waste is determined to be hazardous, use licensed hazardous waste transporter and disposal facility.US DOT RoadProper Shipping Name: AdhesivesHazard Class: 3SECONDARY HAZARD: NoneUN/NA Number: 1133Packing Group: IIIEmergency Response Guide Number: 128IATA CargoPROPER SHIPPING NAME: AdhesivesHazard Class: 3HAZARD CLASS: NoneUN NUMBER: 1133PACKING GROUP: IIIEMS: 3LIMDGPROPER SHIPPING NAME: AdhesivesHazard Class: 3HAZARD CLASS: NoneUN NUMBER: 1133PACKING GROUP: IIIEMS: F-EThe listed transportation classification applies to non-bulk shipments. It does not address regulatory variations due to changes in package size, mode of shipment or other regulatory descriptors. For the most accurate shipping information, refer to your transportation/compliance department.U.S. FEDERAL REGULATIONS: AS FOLLOWS:SARA SECTION 313This product contains the following substances subject to the reporting requirements of Section 313 of Title III of the Superfund Amendment and Reauthorization Act of 1986 and 40 CFR part 372.:Chemical Name CAS Number Weight % Less ThanXylene1330-20-760.0%Ethyl benzene100-41-415.0%Zinc oxide (ZnO)PROPRIETARY 5.0%TOXIC SUBSTANCES CONTROL ACT:INVENTORY STATUSThe chemical substances in this product are on the active TSCA Section 8 Inventory or exempt.EXPORT NOTIFICATIONThis product contains the following chemical substances subject to the reporting requirements of TSCA 12(B) if exported from the United States:NoneUnder HazCom 2012 it is optional to continue using the HMIS rating system. It is important to ensure employees have been trained to recognize the different numeric ratings associated with the HazCom 2012 and HMIS schemes.HMIS RATINGS - HEALTH: 2* FLAMMABILITY: 3 PHYSICAL HAZARD: 0* - Indicates a chronic hazard; see Section 2Revision: Company LogoEffective Date: 09/16/2021The information contained herein is, to the best of our knowledge and belief, accurate. However, since the conditions of handling and use are beyond our control, we make no guarantee of results, and assume no liability for damages incurred byuse of this material. It is the responsibility of the user to comply with all applicable federal, state and local laws and regulations.。
LORD Chemlok 289 290 合质说明书
DescriptionLORD Chemlok ® 289/290 adhesive is a primer/covercoat adhesive system designed for bonding rubber linings to steel, stainless steel, aluminum, titanium, wood and other substrates. It is composed of a mixture of poly-mers, organic compounds and mineral fillers dissolved or dispersed in an organic solvent system. Chemlok289/290 adhesive is suitable for cure by autoclave, open steam or chemical techniques.Features and BenefitsVersatile – bonds many rubber compounds to a variety of substrates.Easy to Apply – applies easily by brush, roll coat or spray methods.Corrosion Resistant – provides excellent corrosion resistance.Chemlok ®289/290 AdhesiveApplicationSurface Preparation – Thoroughly clean metal surfaces prior to primer application. Remove protective oils, cutting oils and greases by solvent degreasing oralkaline cleaning. Remove rust, scale or oxide coatings by grit blasting. Use steel grit to blast clean steel and other ferrous metals. Use aluminum oxide, sand or other nonferrous grit to blast clean stainless steel, aluminum and other nonferrous metals.For further detailed information on surface preparation of specific substrates, refer to Chemlok Adhesives applic-aiton guide. Handle clean metal surfaces with clean gloves to avoid contamination with skin oils.Mixing – Thoroughly stir Chemlok 289 primer and Chemlok 290 covercoat before use, and agitate suffi-ciently during use to keep dispersed solids uniformly suspended.Chemlok 289 primer and Chemlok 290 covercoat are normally used full strength for brush or roll coat applica-tions. For spray application, dilute Chemlok 289 primer with a 1:1 MEK/xylene mixture; dilute Chemlok 290 covercoat with xylene or toluene.Typical Properties*289 Primer 290 Covercoat Appearance Green Liquid Red Liquid Viscositycps @ 25°C (77°F)200 - 45020 - 50Brookfield LVTSpindle 2, 30 rpmSpindle 1, 60 rpmseconds20 - 4030 - 55Zahn Cup #4Zahn Cup #1Density kg/m 3 922.6 - 958.6 862.8 - 886.7(lb/gal)(7.7 - 8.0) (7.2 - 7.4)Solids Content by Weight, % 23 - 26 5.5 - 7.5Flash Point (Seta), °C (°F) 6 (42)7 (44)SolventsXylene, Methyl Ethyl Ketone (MEK) Toluene Theoretical Coverage, m 2/gal (ft 2/gal)55 (591)95 (1018)@ 10.2 micron (0.4 mil) dry film thickness@ 2.5 micron (0.1 mil) dry film thickness*Data is typical and not to be used for specification purposes.Applying – Separately apply primer and covercoat by brush, roll coat or spray methods. For best results, apply adhesive system to surfaces with temperatures less than 38°C (100°F).Regardless of application method, use the following recommended dry film thicknesses for optimum adhesion:Chemlok 289 10.2 micron (0.4 mil)Chemlok 290 2.5 micron (0.1 mil)Drying/Curing – Allow primer to air-dry for 30-60 minutes before applying covercoat to prevent solvent entrapment and subsequent blistering.If parts applied with Chemlok 289 primer remain uncoated for more than seven days, primer must be reapplied prior to Chemlok 290 covercoat applica-tion. Parts coated with Chemlok 290 covercoat can be stored for up to seven days prior to rubber layup without affecting bond performance if protected from sunlight exposure.Cleanup – Use xylene, toluene or MEK for clean up.Shelf Life/StorageShelf life is one year from date of shipment when stored by the recipient in a well ventilated area at 21-27°C(70-80°F) in original, unopened container. Store container in a dry location, away from sunlight. Keep container closed when not in use.Cautionary InformationBefore using this or any LORD product, refer to the Safety Data Sheet (SDS) and label for safe use and handling instructions.For industrial/commercial use only. Must be applied by trained personnel only. Not to be used in household applications. Not for consumer use.2Typical Bond Data*Primer Adhesive Tack Coat 90° Peel(pli)Adhesion AutoclaveNatural Rubber Chemlok 289 Chemlok 290 Chemlok 286 30#/100R60’ @ 132°C (270°F)32 Shore ABromobutyl Chemlok 289 Chemlok 290 EP5879-60 67#/100R60’ @ 149°C (300°F)52 Shore AChloroprene Chemlok 289 none none 113#/100R90’ @ 146°C (295°F) (stock preheated)Open SteamNatural Rubber Chemlok 289 Chemlok 290 Chemlok 286 51#/100R24 hr @ 88°C (190°F)60 Shore ANatural Rubber Chemlok 289 Chemlok 290 Chemlok 286 57#/100R46 hr @ 82°C (180°F)60 Shore AEPDM Chemlok 289 Chemlok 290 EP5879-60 47#/100R56 hr @ 85°C (185°F)48 Shore AChemical CuringNatural Rubber Chemlok 289 Chemlok 290 Chemlok 286 57#/100R Carbon Disulfide Cure5 days @ 38°C (100°F)57 Shore ANatural Rubber Chemlok 289 Chemlok 290 Chemlok 286 57#/100R Carbon Disulfide Cure5 days @ 38°C (100°F)53 Shore A*Data is typical and not to be used for specification purposes.3LORD provides valuable expertise in adhesives and coatings, vibration and motion control, and magnetically responsive technologies. Ourpeople work in collaboration with our customers to help them increase the value of their products. Innovative and responsive in an ever-changing marketplace, we are focused on providing solutions for our customers worldwide.LORD Corporation World Headquarters 111 Lord DriveCary, NC 27511-7923 USACustomer Support Center (in United States & Canada)+1 877 ASK LORD (275 5673)For a listing of our worldwide locations, visit .Values stated in this technical data sheet represent typical values as not all tests are run on each lot of material produced. For formalized product specifications for specific product end uses, contact the Customer Support Center.Information provided herein is based upon tests believed to be reliable. In as much as LORD Corporation has no control over the manner in which others may use this information, it does not guarantee the results to be obtained. In addition, LORD Corporation does not guarantee the perfor-mance of the product or the results obtained from the use of the product or this information where the product has been repackaged by any third party, including but not limited to any product end-user. Nor does the company make any express or implied warranty of merchantability or fitness for a particular purpose concerning the effects or results of such use.Chemlok is a trademark of LORD Corporation or one of its subsidiaries.©2019 LORD Corporation OD DS3137 (Rev.4 10/19)。
CHEMLOK 144 产品说明书
USA SAFETY DATA SHEET1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATIONProduct name:CHEMLOK 144Product Use/Class: Primer for AdhesiveLORD Corporation111 LORD DriveCary, NC 27511-7923 USATelephone: 814 868-3180Non-Transportation Emergency: 814 763-2345Chemtrec 24 Hr Transportation Emergency No.800 424-9300 (Outside Continental U.S. 703 527-3887)EFFECTIVE DATE: 05/19/20212. HAZARDS IDENTIFICATIONGHS CLASSIFICATION:Flammable liquids Category 2Acute toxicity Inhalation - Vapours Category 4 - 17.9% of the mixture consists of ingredient(s) of unknown toxicity.Acute toxicity Inhalation - Dust and Mist Category 4 - 17.9% of the mixture consists of ingredient(s) of unknown toxicity.Skin corrosion/irritation Category 2Serious eye damage/eye irritation Category 2AReproductive toxicity Category 2Specific target organ systemic toxicity (single exposure) Category 1 Central nervous system, HematopoieticSystem, Kidney, Liver, Respiratory systemSpecific target organ systemic toxicity (single exposure) Category 3Specific target organ systemic toxicity (repeated exposure) Category 1 Central nervous system, Kidney,Hematopoietic System, Liver, EarsAspiration hazard Category 1Hazardous to the aquatic environment - acute hazard Category 2Hazardous to the aquatic environment - chronic hazard Category 2GHS LABEL ELEMENTS:Symbol(s)Signal WordD ANGERHazard StatementsHighly flammable liquid and vapor.Harmful if inhaled.Causes skin irritation.Causes serious eye irritation.Suspected of damaging fertility or the unborn child.May cause harm to breast-fed children.Causes damage to organs.(Central nervous system, Hematopoietic System, Kidney, Liver, Respiratory system)May cause drowsiness or dizziness.May cause respiratory irritation.Causes damage to organs through prolonged or repeated exposure.(Central nervous system, Kidney, Hematopoietic System, Liver, Ears)May be fatal if swallowed and enters airways.300000002653Toxic to aquatic life.Toxic to aquatic life with long lasting effects.Precautionary StatementsPreventionKeep away from heat/sparks/open flames/hot surfaces. - No smoking.Ground/Bond container and receiving equipment.Use explosion-proof electrical/ventilating/lighting equipment.Use only non-sparking tools.Take precautionary measures against static discharge.Wear protective gloves/protective clothing/eye protection/face protection.Do not breathe dust/fume/gas/mist/vapors/spray.Wash thoroughly after handling.Do not eat, drink or smoke when using this product.Use only outdoors or in a well-ventilated area.Avoid release to the environment.ResponseIn case of fire: refer to section 5 of SDS for extinguishing media.Call a POISON CENTER or doctor/physician if you feel unwell.IF exposed: Call a POISON CENTER or doctor/physician.Specific treatment (see supplemental first aid instructions on this label).IF INHALED: Remove to fresh air and keep at rest in a position comfortable for breathing.IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower.If skin irritation occurs: Get medical advice/attention.IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do.Continue rinsing.IF SWALLOWED: Immediately call a POISON CENTER or doctor/physician.Do NOT induce vomiting.Collect spillage.StorageStore in a well-ventilated place. Keep cool.Store in a well-ventilated place. Keep container tightly closed.Store locked up.Disposal:Dispose of contents/container in accordance with waste/disposal laws and regulations of your country or particular locality.Other Hazards:This product contains component(s) which have the following warnings; however based on the GHS classification criteria of your country or locale, the product mixture may be outside the respective category(s).Acute: Harmful if absorbed through skin. Vapor harmful; may affect the brain or nervous system causing dizziness, headache or nausea. May cause central nervous system depression characterized by the following progressive steps: headache, dizziness, staggering gait, confusion, unconsciousness or coma. Possible irritation of the respiratory system can occur causing a variety of symptoms such as dryness of the throat, tightness of the chest, and shortness ofbreath.May be harmful if swallowed. Ingestion is not an expected route of entry in industrial or commercial uses.Chronic: ACGIH considers Ethyl alcohol to be an A3 carcinogen (confirmed animal carcinogen with unknownrelevance in humans).withheld.FIRST AID - EYE CONTACT: Flush eyes immediately with large amount of water for at least 15 minutes holding eyelids open while flushing. Get prompt medical attention.FIRST AID - SKIN CONTACT: Flush contaminated skin with large amounts of water while removing contaminated clothing. Wash affected skin areas with soap and water. Get medical attention if symptoms occur.FIRST AID - INHALATION: Move person to fresh air. Restore and support continued breathing. If breathing is difficult, give oxygen. Get immediate medical attention.FIRST AID - INGESTION: If swallowed, do not induce vomiting. Call a physician or poison control center immediately for further instructions. Never give anything by mouth if victim is rapidly losing consciousness, unconscious or convulsing.SUITABLE EXTINGUISHING MEDIA: Carbon Dioxide, Dry Chemical, Foam, Water FogUNSUITABLE EXTINGUISHING MEDIA: Not determined for this product.SPECIFIC HAZARDS POSSIBLY ARISING FROM THE CHEMICAL: Flammable liquid and vapor. Keep containers tightly closed. Isolate from heat, electrical equipment, sparks, open flame, and other sources of ignition. Closed containers may rupture when exposed to extreme heat. Use water spray to keep fire exposed containers cool. During a fire, irritating and/or toxic gases and particulate may be generated by thermal decomposition or combustion.SPECIAL PROTECTIVE EQUIPMENT AND PRECAUTIONS FOR FIRE-FIGHTERS: Wear full firefighting protective clothing, including self-contained breathing apparatus (SCBA). Water spray may be ineffective. If water is used, fog nozzles are preferable.PERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES: Remove all sources of ignition (flame, hot surfaces, and electrical, static or frictional sparks). Avoid contact. Avoid breathing vapors. Use self-contained breathing equipment.ENVIRONMENTAL PRECAUTIONS: Do not contaminate bodies of water, waterways, or ditches, with chemical or used container.METHODS AND MATERIALS FOR CONTAINMENT AND CLEANUP: Keep non-essential personnel a safe distance away from the spill area. Notify appropriate authorities if necessary. Avoid contact. Before attempting cleanup, refer to hazard caution information in other sections of the SDS form. Contain and remove with inert absorbent material and non-sparking tools.HANDLING: Keep closure tight and container upright to prevent leakage. Ground and bond containers when transferring material. Avoid skin and eye contact. Wash thoroughly after handling. Avoid breathing of vapor or spray mists. Do not handle until all safety precautions have been read and understood. Empty containers should not be re-used. Use with adequate ventilation. Because empty containers may retain product residue and flammable vapors, keep away from heat, sparks and flame; do not cut, puncture or weld on or near the empty container. Do not smoke where this product is used or stored.STORAGE: Do not store or use near heat, sparks, or open flame. Store only in well-ventilated areas. Do not puncture, drag, or slide container. Keep container closed when not in use. Refer to OSHA 29CFR Part 1910.106 "Flammable and Combustible Liquids" for specific storage requirements.INCOMPATIBILITY: Strong oxidizers, acids, bases, water.Engineering controls: Sufficient ventilation in pattern and volume should be provided in order to maintain air contaminant levels below recommended exposure limits. Caution: Solvent vapors are heavier than air and collect in lower levels of the work area. Sufficient ventilation (using explosion-proof equipment) should be provided to prevent flammable vapor/air mixtures from accumulating.PERSONAL PROTECTION MEASURES/EQUIPMENT:RESPIRATORY PROTECTION: Use a NIOSH approved chemical/mechanical filter respirator designed toremove a combination of particulates and organic vapor if occupational limits are exceeded. For emergencysituations, confined space use, or other conditions where exposure limits may be greatly exceeded, use an approved air-supplied respirator. For respirator use observe OSHA regulations (29CFR 1910.134) or use in accordance with applicable laws and regulations of your country or particular locality.SKIN PROTECTION: Use neoprene, nitrile, or rubber gloves to prevent skin contact.EYE PROTECTION: Use safety eyewear including safety glasses with side shields and chemical goggles where splashing may occur.OTHER PROTECTIVE EQUIPMENT: Use disposable or impervious clothing if work clothing contamination is likely. Remove and wash contaminated clothing before reuse.HYGIENIC PRACTICES: Wash hands before eating, smoking, or using toilet facility. Do not smoke in anychemical handling or storage area. Food or beverages should not be consumed anywhere this product is handled or stored. Wash thoroughly after handling.Typical values, not to be used for specification purposes.ODOR: Solvent VAPOR PRESSURE: N.D.APPEARANCE: Yellow VAPOR DENSITY: Heavier than Air PHYSICAL STATE: Liquid LOWER EXPLOSIVE LIMIT: 1.1 %(V)UPPER EXPLOSIVE LIMIT: 19 %(V)FLASH POINT: 35 °F, 1 °C 1 °CSetaflash Closed CupBOILING RANGE: 78 - 168 °C EVAPORATION RATE: Slower than n-butyl-acetate AUTOIGNITION TEMPERATURE:N.D.DENSITY: 0.9 g/cm3 (7.47 lb/gal) DECOMPOSITION TEMPERATURE:N.D. VISCOSITY, DYNAMIC: ≥0.9 mPa.s @ 25 °C ODOR THRESHOLD: N.D.VISCOSITY, KINEMATIC: ≥1 mm2/s @ 25 °CSOLUBILITY IN H2O: Insoluble VOLATILE BY WEIGHT: 87.06 %pH: N.A.VOLATILE BY VOLUME: 90.35 %FREEZE POINT: N.D. VOC CALCULATED: 6.5 lb/gal6.5 lb/gal, 779g/lN.D.COEFFICIENT OF WATER/OILDISTRIBUTION:LEGEND: N.A. - Not Applicable, N.E. - Not Established, N.D. - Not DeterminedHAZARDOUS POLYMERIZATION: Hazardous polymerization will not occur under normal conditions. STABILITY: Product is stable under normal storage conditions.CONDITIONS TO AVOID: High temperatures. Sources of ignition.INCOMPATIBILITY: Strong oxidizers, acids, bases, water.HAZARDOUS DECOMPOSITION PRODUCTS: Carbon dioxide, carbon monoxide, chlorine, hydrogen chloride, PhosgeneEXPOSURE PATH: Refer to section 2 of this SDS.SYMPTOMS:Refer to section 2 of this SDS.TOXICITY MEASURES:Germ cell mutagenicity: No classification proposedCarcinogenicity: No classification proposedReproductive toxicity: Category 2 - Suspected of damaging fertility or the unborn child. May cause harm to breast-fed children.Components contributing to classification: Toluene. 2-Butoxyethanol. Methanol.PERSISTENCE AND DEGRADABILITY:Not determined for this product.BIOACCUMULATIVE: Not determined for this product.MOBILITY IN SOIL: Not determined for this product.OTHER ADVERSE EFFECTS: Not determined for this product.DISPOSAL METHOD: Disposal should be done in accordance with Federal (40CFR Part 261), state and local environmental control regulations. If waste is determined to be hazardous, use licensed hazardous waste transporter and disposal facility.US DOT RoadProper Shipping Name: AdhesivesHazard Class: 3SECONDARY HAZARD: NoneUN/NA Number: 1133Packing Group: IIEmergency Response Guide Number: 128IATA CargoPROPER SHIPPING NAME: AdhesivesHazard Class: 3HAZARD CLASS: NoneUN NUMBER: 1133PACKING GROUP: IIEMS: 3LIMDGPROPER SHIPPING NAME: AdhesivesHazard Class: 3HAZARD CLASS: NoneUN NUMBER: 1133PACKING GROUP: IIEMS: F-EThe listed transportation classification applies to non-bulk shipments. It does not address regulatory variations due to changes in package size, mode of shipment or other regulatory descriptors. For the most accurate shipping information, refer to your transportation/compliance department.U.S. FEDERAL REGULATIONS: AS FOLLOWS:SARA SECTION 313This product contains the following substances subject to the reporting requirements of Section 313 of Title III of the Superfund Amendment and Reauthorization Act of 1986 and 40 CFR part 372.:Chemical Name CAS Number Weight % Less ThanToluene108-88-375.0%N-Butanol71-36-3 5.0%2-Butoxyethanol111-76-2 5.0%TOXIC SUBSTANCES CONTROL ACT:INVENTORY STATUSThe chemical substances in this product are on the active TSCA Section 8 Inventory or exempt.EXPORT NOTIFICATIONThis product contains the following chemical substances subject to the reporting requirements of TSCA 12(B) if exported from the United States:NoneUnder HazCom 2012 it is optional to continue using the HMIS rating system. It is important to ensure employees have been trained to recognize the different numeric ratings associated with the HazCom 2012 and HMIS schemes.HMIS RATINGS - HEALTH: 2* FLAMMABILITY: 3 PHYSICAL HAZARD: 0* - Indicates a chronic hazard; see Section 2Revision: Company Logo, Section 2Effective Date: 05/19/2021The information contained herein is, to the best of our knowledge and belief, accurate. However, since the conditions of handling and use are beyond our control, we make no guarantee of results, and assume no liability for damages incurred by use of this material. It is the responsibility of the user to comply with all applicable federal, state and local laws and regulations.。
Chemlok 218产品说明书
Chemlok® 218 Technical Data SheetChemlok® 218 is a one-coat surface treatment used to affix castable and millable polyurethane elastomers to metals and other rigid substrates. It is composed of a mixture of polymers and resins dissolved in an organic solvent system Features and Benefits: Environmentally Resistant – provides excellent resistance to water, salt spray, a variety of solvents and other environmental conditions.Convenient – requires no primer, reducing labor and costs.Elastomers:• Castable Urethane• Millable UrethaneApplication:Surface Preparation – Thoroughly clean metal surfaces prior to application. Remove protective oils, cutting oils and greases by solvent degreasing or alkaline cleaning. Remove rust, scale or oxide coatings by suitable chemical or mechanical cleaning methods.For further detailed information on surface preparation of specific substrates, refer to Chemlok application guide. Mixing – No agitation is required before or during use. If dilution is needed, use either a 1:1 isopropanol:toluene blend (by volume) or glycol ether solvents. Note proper dilution for the various application methods is best achieved by experience.Applying – Apply Chemlok 218 by brush, dip, spray,roll coat or any method that gives uniform coating and avoids excessive runs and tears. Regardless of application method, dry film thickness of Chemlok 218 should be 19.05-31.75 micron (0.75-1.25 mil).Chemlok 219 is an excellent primer to use with Chemlok 218. For castable urethane, the properties of Chemlok 219 and Chemlok 218 are complimentary - Chemlok 219 provides excellent protection as a primer for the metal; Chemlok 218 affixes well to castable polyurethanes. Chemlok 218 is also tolerant of processing conditions such as long prebakes. Together, they increase resistance to a variety of environmental elements.When using Chemlok 219 as a primer, first apply Chemlok 219 and allow it to air-dry. Then apply Chemlok 218 and allow to air-dry. The combination is then prebaked at 121°C (250°F) for the desired time.Drying/Curing – Allow coated parts to air-dry for atleast 60 minutes at room temperature for complete solvent evaporation. The film may be force dried at higher temperatures for shorter periods of time. Dryingfor 15 minutes at 121°C (250°F) has no harmful effect on performance.To enhance cohesive strength, bake coated inserts a minimum of 2 hours at 121°C (250°F). Large inserts will require longer baking time at 121°C (250°F) to negate the heat sink effect.Parts coated with Chemlok 218 may be vulcanizedimmediately after air-drying.Chemlok 218 — Technical Data SheetParker LORDEngineered Materials Group 111 LORD DriveCary, NC 27511-7923USAValues stated in this document represent typical values as not all tests are run on each lot of material produced. For formalized product specifications for specific product end uses, contact the Customer Support Center.Information provided herein is based upon tests believed to be reliable. In as much as Parker LORD has no control over the manner in which others may use this information, it does not guarantee the results to be obtained. In addition, Parker LORD does not guarantee the performance of the product or the results obtained from the use of the product or this information where the product has been repackaged by any third party, including but not limited to any product end-user. Nor does the company make any express or implied warranty of merchantability or fitness for a particular purpose concerning the effects or results of such use.WARNING — USER RESPONSIBILITY . FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE.This document and other information from Parker-Hannifin Corporation, its subsidiaries and authorized distributors provide product or system options for further investigation by users having technical expertise.The user, through its own analysis and testing, is solely responsible for making the final selection of the system and components and assuring that all performance, endurance, maintenance, safety and warning requirements of the application are met. The user must analyze all aspects of the application, follow applicable industry standards, and follow the information concerning the product in the current product catalog and in any other materials provided from Parker or its subsidiaries or authorized distributors.To the extent that Parker or its subsidiaries or authorized distributors provide component or system options based upon data or specifications provided by the user, the user is responsible for determining that such data and specifications are suitable and sufficient for all applications and reasonably foreseeable uses of the components or systems.©2021 Parker Hannifin - All Rights ReservedInformation and specifications subject to change without notice and without liability therefor. Trademarks used herein are the property of their respective owners.OD DS6004CE 04/21 Rev.1Molding procedures that are used with heat vulcanizing urethane elastomers can be used with Chemlok 218adhesive. The cure time and temperature are the same as the process conditions required to vulcanize the urethane compound being molded. Best results are obtained with curing temperatures above 71°C (160°F).Cleanup – Use alcohol, such as isopropanol, or achlorinated solvent, such as trichloroethylene, to clean up small spills.Shelf Life/Storage:Shelf life is one year from date of shipment when stored by the recipient at 21-27°C (70-80°F) in original, unopened container. Do not store or use near heat, sparks or open flame.Cautionary Information:Before using this or any Parker LORD product, refer to the Safety Data Sheet (SDS) and label for safe use and handling instructions.For industrial/commercial use only. Required to use under organized emissions. Must be applied by trained personnel only. Not to be used in household applications. Not for consumer use.Chemlok® 218技术说明书Chemlok® 218单涂型表面处理剂可用于帮助和促进浇注型和混炼型聚氨酯弹性体附着至金属及其他硬质基材。
LORD Chemlok 258XN 非导电一层粘合剂说明书
DescriptionLORD Chemlok ® 258XN adhesive is a non-conductive, one-coat adhesive that will bond unvulcanizedrubber compounds to metal or other dissimilar rubber compounds. It is composed of a mixture of polymers, organic compounds and mineral fi llers dissolved or dispersed in an organic solvent system.Chemlok 258XN adhesive is ideal of use in electrical component applications. A single coat of Chemlok258XN adhesive will bond compounds based on natural rubber (NR), polyisoprene (IR), styrene-butadiene (SBR), polybutadiene (BR), polychloroprene (CR),nitrile (NBR), butyl (IIR) and EPDM polymers to metals. These metals include carbon and alloy steels, stainless steel, aluminum, copper and copper alloys, magnesium and zinc, as well as a variety of plastics, epoxy and vinyl ester.Features and Benefi tsNon-Conductive – formulated without carbon black for use in electrical applications.Excellent Adhesion – provides superior adhesive perfor-mance without ozone depleting solvents.Convenient – requires only a single coat for most appli-cations, reducing labor, solvent usage, inventory and shipping costs.Chemlok ®258XN AdhesiveApplicationSurface Preparation – Thoroughly clean metal surfaces prior to primer application. Remove protective oils, cutting oils and greases by solvent degreasing oralkaline cleaning. Remove rust, scale or oxide coatings by suitable chemical or mechanical cleaning methods.•Chemical CleaningChemical treatments are readily adapted to auto-mated metal treatment and adhesive application lines. Chemical treatments are also used on metal parts that would be distorted by blast cleaning or where tight tolerances must be maintained. Phos-phatizing is a commonly used chemical treatment for steel, while conversion coatings are commonly used for aluminum.•Mechanical CleaningGrit blasting is the most widely used method ofmechanical cleaning. However machining, grinding or wire brushing can be used. Use steel grit to blast clean steel, cast iron and other ferrous metals. Use aluminum oxide, sand or other nonferrous grit to blast clean stainless steel, aluminum, brass, zinc and other nonferrous metals.For further detailed information on surface preparation of specifi c substrates, refer to Chemlok Adhesives appli-cation guide. Handle clean metal surfaces with clean gloves to avoid contamination with skin oils.Typical Properties*AppearanceBrown Liquid Viscosity, cps @ 25°C (77°F)150-600Brookfi eld LVT Spindle 2, 30 rpmDensity kg/m 3 994.5-1030.5(lb/gal)(8.3-8.6)Solids Content by Weight, % 22.5-26.5Flash Point (Seta), °C (°F) 29 (85)SolventsXylene, Monochlorotoluene*Data is typical and not to be used for specification purposes.LORD provides valuable expertise in adhesives and coatings, vibration and motion control, and magnetically responsive technologies. Ourpeople work in collaboration with our customers to help them increase the value of their products. Innovative and responsive in an ever-changing marketplace, we are focused on providing solutions for our customers worldwide ... Ask Us How.LORD Corporation World Headquarters 111 Lord DriveCary, NC 27511-7923 USACustomer Support Center (in United States & Canada)+1 877 ASK LORD (275 5673)For a listing of our worldwide locations, visit .Values stated in this technical data sheet represent typical values as not all tests are run on each lot of material produced. For formalized product specifi cations for specifi c product end uses, contact the Customer Support rmation provided herein is based upon tests believed to be reliable. In as much as LORD Corporation has no control over the manner in which others may use this information, it does not guarantee the results to be obtained. In addition, LORD Corporation does not guarantee the perfor-mance of the product or the results obtained from the use of the product or this information where the product has been repackaged by any third party, including but not limited to any product end-user. Nor does the company make any express or implied warranty of merchantability or fi tness for a particular purpose concerning the effects or results of such use.Chemlok and “Ask Us How” are trademarks of LORD Corporation or one of its subsidiaries.©2010 LORD Corporation OD DS3267 (Rev.5 7/10)Mixing – Thoroughly stir Chemlok 258XN adhesive before use, and agitate suffi ciently during use to keep dispersed solids uniformly suspended. Mix drums 8 hours at 30-60 rpm before using.Chemlok 258XN adhesive is used full strength for brush applications. If application method requires dilution, use xylene or toluene as diluents.Applying – Apply Chemlok 258XN adhesive by brush, dip, spray method.When using Chemlok 258XN adhesive as a one-coat adhesive, the dry fi lm thickness should be maintained at 20.3-25.4 micron (0.8-1.0 mil). When used as a covercoat over a primer, the dry fi lm thickness of Chemlok 258XN adhesive should be 10.2-17.8 micron (0.4-0.7 mil).Drying/Curing – Allow the applied adhesive to dry until visual examination of the fi lm has shown that all solvent has evaporated. This will take approximately 30-60 minutes at room temperature. Drying times may beshortened by either preheating the metal inserts or oven drying after application. Metal parts may be preheated to a maximum of 65°C (150°F) prior to adhesive application. For coated parts, moderate drying temperatures should be used, but temperatures as high as 149°C (300°F) may be used for very short periods of time. Maximum air fl ow at minimum temperatures will give the best results.Dried fi lms of Chemlok 258XN adhesive are non-tacky; therefore, coated parts can be piled into tote pans for subsequent processing. Wear clean gloves when handling coated parts and cover tote pans to prevent contamination by dirt, dust, grease, oil, etc. If coated parts are properly protected, long layover times between adhesive application and bonding usually have no adverse effect on the bond.Chemlok 258XN adhesive can be used in compression, transfer and injection molding procedures. Ideal bondingconditions involve a minimum amount of time between loading the adhesive coated parts and elastomervulcanization. However, Chemlok 258XN adhesive will resist moderate prebake times without affecting bond performance.Shelf Life/StorageShelf life is six months from date of shipment when stored at 21-27°C (70-80°F) in original, unopened container.Cautionary InformationBefore using this or any LORD product, refer to the Mate-rial Safety Data Sheet (MSDS) and label for safe use and handling instructions.For industrial/commercial use only. Must be applied by trained personnel only. Not to be used in household applications. Not for consumer use.。
胎片应用指南：产品应用、价值观点说明书
Tire Application GuideProductApplicationValue PropositionChemlok 8007/8210Bond RFID to inside of tire• Provides high bond strength• Reliable and provides consistent product performance Chemlok 8008/8216Thermoset EP-20Encapsulate RFID for bonding to tire• Provides environmental resistance • Provides heat resistance • Low viscosity LORD 7701Bond rubber label to sidewall• Non-yellowing • Quick curing• Provides high bond strength •Easy to applyLORD 7556 A/B LORD 7150 A/B Chemlok 205/6411Bonds rubber EPDM valves• Provides environmental resistance • Provides high bond strength LORD TB 7620Bond foam to inside of tire • Provides high bond strength • Low durometer/high flexibility LORD 7542 A/B Chemlok 205/Fusor 121Flexible foam for sound deadening• Simplifies application of foam to tire • Replaces both foam and adhesive Chemosil 211/Chemlok 6417Bond spikes and studs to tire treads• Provides environmental resistance • Provides low-temperature resistanceQDO Curing of butyl stocks• Improves heat resistance of butyl stocksDBQDOChemlok EP2906-27AProduct ApplicationLORD has been developing adhesive technologies for more than 60 years. Our products are proven, reliable and consistently perform in demanding environments like the tire industry. We collaborate with our customers to incorporate the latest tire technology into their products, enabling them to have a more efficient manufacturing process and produce more robust tires.FoamRFIDRubber label Spikes and studs EPDM valveValues stated herein represent typical values as not all tests are run on each lot of material produced. For formalized product specifications for specific product end uses, contact the Customer Support Center.Information provided herein is based upon tests believed to be reliable. In as much as LORD Corporation has no control over the manner in which others may use this information, it does not guarantee the results to be obtained. In addition, LORD Corporation does not guarantee the performance of the product or the results obtained from the use of the product or this information where the product has been repackaged by any third party, including but not limited to any product end-user. Nor does the company make any express or implied warranty of merchantability or fitness for a particular purpose concerning the effects or results of such use.LORD, Chemlok, Thermoset and Fusor are trademarks of LORD Corporation or one of its subsidiaries.LORD provides valuable expertise in adhesives and coatings, vibration and motion control, and magnetically responsive technologies. Our people work in collaboration with our customers to help them increase the value of their products. Innovative and responsive in an ever-changing marketplace, we are focused on providing solutions for our customers worldwide.LORD CorporationWorld Headquarters111 Lord DriveCary, NC 27511-7923USACustomer Support Center (in United States & Canada)+1 877 ASK LORD (275 5673)For a listing of our worldwide locations, visit .©2019 LORD Corporation OD PB8375 (Rev.0 6/19)。
CHEMLOK 220产品说明说明书
USA SAFETY DATA SHEET3000000011791. CHEMICAL PRODUCT AND COMPANY IDENTIFICATIONProduct name: CHEMLOK 220 Product Use/Class:AdhesiveLORD Corporation 111 LORD DriveCary, NC 27511-7923 USATelephone: 814 868-3180Non-Transportation Emergency: 814 763-2345 Chemtrec 24 Hr Transportation Emergency No.800 424-9300 (Outside Continental U.S. 703 527-3887)EFFECTIVE DATE: 02/11/20202. HAZARDS IDENTIFICATIONGHS CLASSIFICATION:Flammable liquids Category 3Skin corrosion/irritation Category 2Serious eye damage/eye irritation Category 2A Skin sensitization Category 1 Carcinogenicity Category 1B Reproductive toxicity Category 2Specific target organ systemic toxicity (single exposure) Category 3Specific target organ systemic toxicity (single exposure) Category 1 Central nervous system, Liver, Respiratory system, KidneySpecific target organ systemic toxicity (single exposure) Category 2 blood system Specific target organ systemic toxicity (single exposure) Category 3Specific target organ systemic toxicity (repeated exposure) Category 1 Liver, Nervous system, Respiratory system Specific target organ systemic toxicity (repeated exposure) Category 2 Ears, Kidney, blood system Hazardous to the aquatic environment - acute hazard Category 2 Hazardous to the aquatic environment - chronic hazardCategory 2GHS LABEL ELEMENTS: Symbol(s)Signal WordD ANGERHazard StatementsFlammable liquid and vapor. Causes skin irritation.Causes serious eye irritation.May cause an allergic skin reaction. May cause cancer.Suspected of damaging fertility or the unborn child. May cause harm to breast-fed children. May cause drowsiness or dizziness.Causes damage to organs.(Central nervous system, Liver, Respiratory system, Kidney) May cause damage to organs.(blood system) May cause respiratory irritation.Causes damage to organs through prolonged or repeated exposure.(Liver, Nervous system, Respiratory system)May cause damage to organs through prolonged or repeated exposure.(Ears, Kidney, blood system)Toxic to aquatic life.Toxic to aquatic life with long lasting effects.Precautionary StatementsPreventionKeep away from heat/sparks/open flames/hot surfaces. - No smoking.Ground/Bond container and receiving equipment.Use explosion-proof electrical/ventilating/lighting equipment.Use only non-sparking tools.Take precautionary measures against static discharge.Obtain special instructions before use.Do not handle until all safety precautions have been read and understood.Wear protective gloves/protective clothing/eye protection/face protection.Use personal protective equipment as required.Do not breathe dust/fume/gas/mist/vapors/spray.Wash thoroughly after handling.Do not eat, drink or smoke when using this product.Use only outdoors or in a well-ventilated area.Contaminated work clothing should not be allowed out of the workplace.Avoid release to the environment.ResponseIn case of fire: refer to section 5 of SDS for extinguishing media.Call a POISON CENTER or doctor/physician if you feel unwell.IF exposed: Call a POISON CENTER or doctor/physician.Specific treatment (see supplemental first aid instructions on this label).IF INHALED: Remove to fresh air and keep at rest in a position comfortable for breathing.IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower.If skin irritation or rash occurs: Get medical advice/attention.IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do.Continue rinsing.Collect spillage.StorageStore in a well-ventilated place. Keep cool.Store in a well-ventilated place. Keep container tightly closed.Store locked up.Disposal:Dispose of contents/container in accordance with waste/disposal laws and regulations of your country or particular locality.Other Hazards:This product contains component(s) which have the following warnings; however based on the GHS classification criteria of your country or locale, the product mixture may be outside the respective category(s).Acute: Vapor harmful; may affect the brain or nervous system causing dizziness, headache or nausea. Possibleirritation of the respiratory system can occur causing a variety of symptoms such as dryness of the throat, tightness of the chest, and shortness of breath. In elevated-temperature applications, product may release vapors that may produce cyanosis in the absence of sufficient ventilation or adequate respiratory protection. May cause central nervous system depression characterized by the following progressive steps: headache, dizziness, staggering gait, confusion,unconsciousness or coma.May be harmful if swallowed. Ingestion is not an expected route of entry in industrial or commercial uses.Chronic: May affect the gastrointestinal system. May affect the blood and blood-forming organs. IARC and NTP have determined that there is sufficient evidence for carcinogenicity of tetrachloroethylene to experimental animals and limited evidence in humans. Overexposure to lead in this product can damage the nervous, urinary,gastrointestinal, blood, blood-forming, and reproductive systems. Lead and lead compounds have been classified by IARC as probable human carcinogens (Group 2A), and by NTP as reasonably anticipated human carcinogens.Ethylbenzene has been classified by IARC as a possible human carcinogen (Group 2B) and reported by NTP to show clear evidence for carcinogenicity in animals. IARC has designated carbon black as Group 2B - inadequate evidence for carcinogenicity in humans, but sufficient evidence in experimental animals. In 2006 IARC reaffirmed its 1995finding that there is "inadequate evidence" from human health studies to assess whether carbon black causes cancer in humans. Further, epidemiological evidence from well-conducted investigations has shown no causative link between carbon black exposure and the risk of malignant or non-malignant respiratory disease in humans. The nitrogensubstituted aromatic in this product gave positive results for mutagenicity in an Ames Assay study while two other mutagenicity studies proved negative.3. COMPOSITION/INFORMATION ON INGREDIENTSChemical Name CAS Number RangeXylene1330-20-745 - 50%Tetrachloroethylene127-18-415 - 20%Ethyl benzene100-41-410 - 15%Carbon black1333-86-4 1 - 5%Nitrogen substituted aromatic PROPRIETARY 1 - 5%Lead oxide phosphonate12141-20-7 1 - 5%Toluene108-88-30.1 - 0.9%Any "PROPRIETARY" component(s) in the above table is considered trade secret, thus the specific chemical and its exact concentration is being withheld.4. FIRST AID MEASURESFIRST AID - EYE CONTACT: Flush eyes immediately with large amount of water for at least 15 minutes holding eyelids open while flushing. Get prompt medical attention.FIRST AID - SKIN CONTACT: Flush contaminated skin with large amounts of water while removing contaminated clothing. Wash affected skin areas with soap and water. Get medical attention if symptoms occur.FIRST AID - INHALATION: Move person to fresh air. Restore and support continued breathing. If breathing is difficult, give oxygen. Get immediate medical attention.FIRST AID - INGESTION: If swallowed, do not induce vomiting. Call a physician or poison control center immediately for further instructions. Never give anything by mouth if victim is rapidly losing consciousness, unconscious or convulsing.5. FIRE-FIGHTING MEASURESSUITABLE EXTINGUISHING MEDIA: Carbon Dioxide, Dry Chemical, Foam, Water FogUNSUITABLE EXTINGUISHING MEDIA: Not determined for this product.SPECIFIC HAZARDS POSSIBLY ARISING FROM THE CHEMICAL: Flammable liquid and vapor. Keep containers tightly closed. Isolate from heat, electrical equipment, sparks, open flame, and other sources of ignition. Closed containers may rupture when exposed to extreme heat. Use water spray to keep fire exposed containers cool. During a fire, irritating and/or toxic gases and particulate may be generated by thermal decomposition or combustion.SPECIAL PROTECTIVE EQUIPMENT AND PRECAUTIONS FOR FIRE-FIGHTERS: Wear full firefighting protective clothing, including self-contained breathing apparatus (SCBA). Water spray may be ineffective. If water is used, fog nozzles are preferable.6. ACCIDENTAL RELEASE MEASURESPERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES: Remove all sources of ignition (flame, hot surfaces, and electrical, static or frictional sparks). Avoid contact. Avoid breathing vapors. Use self-contained breathing equipment.ENVIRONMENTAL PRECAUTIONS: Do not contaminate bodies of water, waterways, or ditches, with chemical or used container.METHODS AND MATERIALS FOR CONTAINMENT AND CLEANUP: Keep non-essential personnel a safe distance away from the spill area. Notify appropriate authorities if necessary. Avoid contact. Before attempting cleanup, refer to hazard caution information in other sections of the SDS form. Contain and remove with inert absorbent material and non-sparking tools.7. HANDLING AND STORAGEHANDLING: Keep closure tight and container upright to prevent leakage. Ground and bond containers when transferring material. Avoid skin and eye contact. Wash thoroughly after handling. Avoid breathing of vapor or spray mists. Do not handle until all safety precautions have been read and understood. Empty containers should not be re-used. Avoid breathing sanding dust from this product. Avoid using pressurizable equipment which has aluminum or zinc parts; this product contains chlorinated solvents. Use with adequate ventilation. Because empty containers may retain product residue and flammable vapors, keep away from heat, sparks and flame; do not cut, puncture or weld on or near the empty container. This product contains inorganic lead; potential lead exposure exists when applying or sanding this product. Use of this product should comply with the OSHA Lead Standard (29 CFR 1910.1025) or where applicable the OSHA Construction Standard for lead (29 CFR 1926.62). Do not smoke where this product is used or stored.STORAGE: Do not store or use near heat, sparks, or open flame. Store only in well-ventilated areas. Do not puncture, drag, or slide container. Keep container closed when not in use. Refer to OSHA 29CFR Part 1910.106 "Flammable and Combustible Liquids" for specific storage requirements.INCOMPATIBILITY: Strong oxidizers, acids, bases, water.; Aluminum, zinc, caustics, halogens.8. EXPOSURE CONTROLS/PERSONAL PROTECTIONCOMPONENT EXPOSURE LIMITChemical Name ACGIH TLV-TWA ACGIH TLV-STELOSHA PEL-TWAOSHA PEL-CEILINGSkinXylene100 ppm150 ppm435 mg/m3100 ppmN.E.N.A.Tetrachloroethylene25 ppm100 ppm100 ppm 100 ppmN.A.Ethyl benzene20 ppm N.E.435 mg/m3100 ppmN.E.N.A.Carbon black 3 mg/m3N.E. 3.5 mg/m3 N.E.N.A.Nitrogen substituted aromatic N.E.N.E.N.E. N.E.N.A.Lead oxide phosphonate0.05 mg/m3N.E.0.05 mg/m3 N.E.N.A.Toluene20 ppm N.E.200 ppm 300 ppmN.A.N.A. - Not Applicable, N.E. - Not Established, S - Skin DesignationEngineering controls: Sufficient ventilation in pattern and volume should be provided in order to maintain air contaminant levels below recommended exposure limits. Caution: Solvent vapors are heavier than air and collect in lower levels of the work area. Sufficient ventilation (using explosion-proof equipment) should be provided to prevent flammable vapor/air mixtures from accumulating.PERSONAL PROTECTION MEASURES/EQUIPMENT:RESPIRATORY PROTECTION: Use a NIOSH approved chemical/mechanical filter respirator designed to remove a combination of particulates and organic vapor if occupational limits are exceeded. For emergencysituations, confined space use, or other conditions where exposure limits may be greatly exceeded, use an approved air-supplied respirator. For respirator use observe OSHA regulations (29CFR 1910.134) or use in accordance with applicable laws and regulations of your country or particular locality.SKIN PROTECTION: Use neoprene, nitrile, or rubber gloves to prevent skin contact.EYE PROTECTION: Use safety eyewear including safety glasses with side shields and chemical goggles where splashing may occur.OTHER PROTECTIVE EQUIPMENT: Use disposable or impervious clothing if work clothing contamination is likely. Remove and wash contaminated clothing before reuse.HYGIENIC PRACTICES: Wash hands before eating, smoking, or using toilet facility. Do not smoke in anychemical handling or storage area. Food or beverages should not be consumed anywhere this product is handled or stored. Wash thoroughly after handling.9. PHYSICAL AND CHEMICAL PROPERTIESTypical values, not to be used for specification purposes.ODOR: Solvent VAPOR PRESSURE: N.D.APPEARANCE: Black VAPOR DENSITY: Heavier than Air PHYSICAL STATE: Liquid LOWER EXPLOSIVE LIMIT: 1 %(V)UPPER EXPLOSIVE LIMIT: 7 %(V)FLASH POINT: 83 °F, 28 °C SetaflashClosed CupBOILING RANGE: 121 - 141 °C EVAPORATION RATE: Slower than n-butyl-acetate AUTOIGNITION TEMPERATURE:N.D.DENSITY: 1.07 g/cm3 - 8.94 lb/gal DECOMPOSITION TEMPERATURE:N.D. VISCOSITY, DYNAMIC: ≥135 mPa.s @ 25 °C ODOR THRESHOLD: N.D.VISCOSITY, KINEMATIC: ≥126 mm2/s @ 25 °CSOLUBILITY IN H2O: Insoluble VOLATILE BY WEIGHT: 75.21 %pH: N.A.VOLATILE BY VOLUME: 84.14 %FREEZE POINT: N.D. VOC CALCULATED: 5.76 lb/gal, 690 g/lN.D. METHOD 24: 6.17 lb/gallon COEFFICIENT OF WATER/OILDISTRIBUTION:LEGEND: N.A. - Not Applicable, N.E. - Not Established, N.D. - Not Determined10. STABILITY AND REACTIVITYHAZARDOUS POLYMERIZATION: Hazardous polymerization will not occur under normal conditions. STABILITY: Product is stable under normal storage conditions. Product is stable under normal storage conditions. CONDITIONS TO AVOID: High temperatures. Sources of ignition.; Aluminum or galvanized parts in a closed system. INCOMPATIBILITY: Strong oxidizers, acids, bases, water.; Aluminum, zinc, caustics, halogens.HAZARDOUS DECOMPOSITION PRODUCTS: Carbon dioxide, carbon monoxide, chlorine, hydrogen chloride, Bromine, hydrogen bromide, Phosgene, Lead fume, Oxides of nitrogen11. TOXICOLOGICAL INFORMATIONEXPOSURE PATH: Refer to section 2 of this SDS.SYMPTOMS:Refer to section 2 of this SDS.TOXICITY MEASURES:Chemical Name LD50/LC50Xylene Oral LD50: Rat3,500 mg/kgDermal LD50: Rabbit> 4,350 mg/kgInhalation LC50: Rat29.08 mg/l/4 hTetrachloroethylene Oral LD50: Rat2,629 mg/kgInhalation LC50: Rat27.8 mg/l/4 hEthyl benzene Oral LD50: Rat3,500 mg/kgDermal LD50: Rabbit15,400 mg/kgInhalation LC50: Rat17.4 mg/l/4 hCarbon black Oral LD50: Rat> 15,400 mg/kgDermal LD50: Rabbit> 3 g/kgGHS LC50 (vapour): Acute toxicity point estimate55 mg/lNitrogen substituted aromatic Oral LD50: rat1,100 mg/kgLead oxide phosphonate GHS LC50 (vapour): Acute toxicity point estimate55 mg/lToluene Oral LD50: Rat2,600 mg/kgDermal LD50: Rabbit12,000 mg/kgInhalation LC50: Rat12.5 mg/l/4 hGerm cell mutagenicity: No classification proposedCarcinogenicity: Category 1B - May cause cancer.Components contributing to classification: Tetrachloroethylene. Ethyl benzene. Lead oxide phosphonate.Reproductive toxicity: Category 2 - Suspected of damaging fertility or the unborn child. May cause harm to breast-fed children.Components contributing to classification: Xylene. Tetrachloroethylene. Ethyl benzene. Lead oxide phosphonate.Toluene.12. ECOLOGICAL INFORMATIONECOTOXICITY:Chemical Name EcotoxicityXylene Fish: Pimephales promelas13.4 mg/l96 h flow-throughOncorhynchus mykiss2.661 - 4.093 mg/l96 h StaticOncorhynchus mykiss13.5 - 17.3 mg/l96 hLepomis macrochirus13.1 - 16.5 mg/l96 h flow-throughLepomis macrochirus19 mg/l96 hLepomis macrochirus7.711 - 9.591 mg/l96 h StaticPimephales promelas23.53 - 29.97 mg/l96 h StaticCyprinus carpio780 mg/l96 h semi-staticCyprinus carpio> 780 mg/l96 hPoecilia reticulata30.26 - 40.75 mg/l96 h StaticInvertebrates: water flea3.82 mg/l48 hGammarus lacustris0.6 mg/l48 hTetrachloroethylene Fish: Pimephales promelas12.4 - 14.4 mg/l96 h flow-throughPimephales promelas8.6 - 13.5 mg/l96 h StaticLepomis macrochirus11.0 - 15.0 mg/l96 h StaticOncorhynchus mykiss4.73 - 5.27 mg/l96 h flow-throughInvertebrates: Daphnia magna6.1 - 9.0 mg/l48 h StaticPlants: Pseudokirchneriella subcapitata> 500 mg/l96 hEthyl benzene Fish: Oncorhynchus mykiss11.0 - 18.0 mg/l96 h StaticOncorhynchus mykiss4.2 mg/l96 h semi-staticPimephales promelas7.55 - 11 mg/l96 h flow-throughLepomis macrochirus32 mg/l96 h StaticPimephales promelas9.1 - 15.6 mg/l96 h StaticPoecilia reticulata9.6 mg/l96 h StaticInvertebrates: Daphnia magna1.8 - 2.4 mg/l48 hPlants: Pseudokirchneriella subcapitata4.6 mg/l72 hPseudokirchneriella subcapitata> 438 mg/l96 hPseudokirchneriella subcapitata2.6 - 11.3 mg/l72 h StaticPseudokirchneriella subcapitata1.7 - 7.6 mg/l96 h StaticCarbon black N.D.Nitrogen substituted aromatic N.D.Lead oxide phosphonate N.D.Toluene Fish: Pimephales promelas15.22 - 19.05 mg/l96 h flow-throughPimephales promelas12.6 mg/l96 h StaticOncorhynchus mykiss5.89 - 7.81 mg/l96 h flow-throughOncorhynchus mykiss14.1 - 17.16 mg/l96 h StaticOncorhynchus mykiss5.8 mg/l96 h semi-staticLepomis macrochirus11.0 - 15.0 mg/l96 h StaticOryzias latipes54 mg/l96 h StaticPoecilia reticulata28.2 mg/l96 h semi-staticPoecilia reticulata50.87 - 70.34 mg/l96 h StaticInvertebrates: Daphnia magna5.46 - 9.83 mg/l48 h StaticDaphnia magna11.5 mg/l48 hPlants: Pseudokirchneriella subcapitata> 433 mg/l96 hPseudokirchneriella subcapitata12.5 mg/l72 h StaticPERSISTENCE AND DEGRADABILITY:Not determined for this product.BIOACCUMULATIVE: Not determined for this product.MOBILITY IN SOIL: Not determined for this product.OTHER ADVERSE EFFECTS: Not determined for this product.13. DISPOSAL CONSIDERATIONSDISPOSAL METHOD: Disposal should be done in accordance with Federal (40CFR Part 261), state and local environmental control regulations. If waste is determined to be hazardous, use licensed hazardous waste transporter and disposal facility.14. TRANSPORT INFORMATIONUS DOT RoadProper Shipping Name: AdhesivesHazard Class: 3SECONDARY HAZARD: NoneUN/NA Number: 1133Packing Group: IIIEmergency Response Guide Number: 128IATA CargoPROPER SHIPPING NAME: AdhesivesHazard Class: 3HAZARD CLASS: NoneUN NUMBER: 1133PACKING GROUP: IIIEMS: 3LIMDGPROPER SHIPPING NAME: AdhesivesHazard Class: 3HAZARD CLASS: NoneUN NUMBER: 1133PACKING GROUP: IIIEMS: F-EThe listed transportation classification applies to non-bulk shipments. It does not address regulatory variations due to changes in package size, mode of shipment or other regulatory descriptors. For the most accurate shipping information, refer to your transportation/compliance department.15. REGULATORY INFORMATIONU.S. FEDERAL REGULATIONS: AS FOLLOWS:SARA SECTION 313This product contains the following substances subject to the reporting requirements of Section 313 of Title III of the Superfund Amendment and Reauthorization Act of 1986 and 40 CFR part 372.:Chemical Name CAS Number Weight % Less ThanXylene1330-20-750.0%Tetrachloroethylene127-18-420.0%Ethyl benzene100-41-415.0%Lead oxide phosphonate12141-20-7 5.0%Toluene108-88-30.9%TOXIC SUBSTANCES CONTROL ACT:INVENTORY STATUSThe chemical substances in this product are on the TSCA Section 8 Inventory.EXPORT NOTIFICATIONThis product contains the following chemical substances subject to the reporting requirements of TSCA 12(B) if exported from the United States:None16. OTHER INFORMATIONUnder HazCom 2012 it is optional to continue using the HMIS rating system. It is important to ensure employees have been trained to recognize the different numeric ratings associated with the HazCom 2012 and HMIS schemes.HMIS RATINGS - HEALTH: 2* FLAMMABILITY: 3 PHYSICAL HAZARD: 0* - Indicates a chronic hazard; see Section 2Revision: Section 2, Section 3, Section 8, Section 11, Section 12Effective Date: 02/11/2020DISCLAIMERThe information contained herein is, to the best of our knowledge and belief, accurate. However, since the conditions of handling and use are beyond our control, we make no guarantee of results, and assume no liability for damages incurred by use of this material. It is the responsibility of the user to comply with all applicable federal, state and local laws and regulations.。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
—— CHEMLOK胶粘剂应用
LORD CHINA 2007
Company Confidential
Adhesives 开姆洛克胶粘剂 •Chemlok Lord Corporation was founded in 1924. 1st products were
•
designed to isolate vibration on trolley cars. Chemlok 205 / 220 was commercialized in 1956 to bond rubber to metal.
为：145℃～185℃。
5
Company Confidential
5
内容
• 第 I 部分 基材的准备 • 第II部分 胶粘剂应用技术 • 第III部分 常见粘接问题解决
6
Company Confidential
6
橡胶与金属粘接步骤
橡胶金属 粘接过程 基材准备 胶粘剂的准备 胶粘剂的使用 硫化
机械处理
18
磷化处理
•
典型的磷化生产线
19
Company Confidential
19
铝件的铬化处理
• 脱脂
• 在65～70℃，浸于下述溶液中浸10分钟 水 450ml H2SO4（1.84） 80ml Na2Cr2O7 15g
• 水洗，干燥，立即涂胶。
20
Company Confidential
20
铝件的阳极化处理
31
Company Confidential
31
32
Company Confidential
32
胶粘剂的稀释
• 选用正确的胶粘剂，参照产品说明书。错误的胶粘剂会导
致工艺和粘结问题。
• 添加稀释剂时，应缓慢加入，以避免产生凝胶或分相等现
象。
• 用Zahn氏杯测量粘度，确定合适范围用于过程控制。 • 胶粘剂稀释会影响操作的工艺性和膜厚的均匀性。
10
Company Confidential
10
基材的表面处理
• 脱脂－机械处理－清洗
• 脱脂－化学处理
• 脱脂－机械处理－清洗－化学处理
11
Company Confidential
11
脱脂方法
• 碱液脱脂 • 溶剂脱脂
－浸渍 －清洗 －蒸汽 超声脱脂
•
12
Company Confidential
• 建议采用铬酸阳极氧化处理, 不封闭. • CrO3 50-60g/L, 35C, 铝件阳极1.5-2.5A/dm2, 60min.
• 阳极化后能在铝件表面形成氧化膜，具有提高铝的防腐性能和橡
胶的粘合性能。
• 在处理前，必须确保铝材的表面的干净;
处理后的工件必须确保膜厚
21
Company Confidential
•
• •
38
Company Confidential
38
零件行径
搅拌器 胶粘剂
溢流
隔膜泵 50 目过滤器
39 Company Confidential 39
自动浸涂生产线
40
Company Confidential
40
喷涂应用
• 较高生产效率，并能得到均匀的膜厚。 • 工件经过预热，可以挥发过多的水分等，以改善工件表面
15
蒸汽脱脂
• • • • • •
溶剂 1、1、1－三氯乙烷、三氯乙烯、四氯乙烯 金属件不可侵入溶剂，也不可高于冷凝区，相互间不接触。 金属件温度达到溶剂沸点，脱脂结束。 溶剂PH值保持在7.0～7.5之间。 溶剂含油达25％时应更新。
16
Company Confidential
16
机械处理
• 抛丸或喷砂 •
材料：钢珠，菱角砂，石英砂，金刚玉等， 喷砂或抛丸后的零件需清洗。 常用的设备
17
Company Confidential
17
磷化处理
• 脱脂/除锈
清洗
清洗
表面调整 磷化 沸水洗 烘干
• 磷化－磷化膜厚度3.5g/m2， 磷化膜呈微晶结构(图示)， 而不应呈巨晶结构
18
Company Confidential
33
Company Confidential
33
胶粘剂的干膜厚度
• 推荐的胶粘剂干膜的厚度
底涂 5～10 μm 面涂 12～25 μm 单涂 18 ~ 30 μm 后硫化粘结 25 ~ 40 μm 不同的胶粘剂可以参照产品说明书 硅烷类的胶粘剂的膜厚应薄一些，一般小于1.2 μm 一张A4纸的厚度约为75-100 μm
• • • •
的浸润性。 转换效率较差，10~50%,依据产品的结构和设备。 推荐使用50目的过滤器。 喷涂用的压缩空气必须经过油水分离。 推荐使用的喷枪：HVLP 高雾化低压力，如BINKS;岩田等
41
Company Confidential
41
喷涂应用 － 喷涂方式
• 手工和自动喷涂
• 两种供胶方式：虹吸杯和压力供给 • 加热喷涂和静电喷涂 • 不推荐使用无气喷涂
30
Company Confidential
30
典型的搅拌
容器 1 /2 品脱 (1kg) 1 加仑 (3-4kg) 5 加仑 (17-23kg) 搅拌方法 手工搅拌 手工搅拌 搅拌时间 5～10分钟 15分钟
先手工搅拌和气，电 15～30分钟 动搅拌
55 加仑 (200kg)
手动曲柄搅拌和气， 8小时连续 电动搅拌器
涂刷应用
• 适用于很小的零件和特殊的应用区域
• 制造费用低但涂刷质量较差，均匀一致性差。 • 选择合适的刷子 • 建议使用天然毛的刷子；水基型胶粘剂用发泡型的工具。
37
Company Confidential
37
浸涂应用
• 浸涂适合于工件表面全部需胶粘剂的情况，但浸涂后零件 •
表面涂层厚度从上至下会有梯度。 手工或自动浸涂生产线，使用输送系统，均有高的输出量， 生产效率高，一般输送的线速度是60～180厘米/分钟。 从胶粘剂溶液中提出的速度应缓慢些，一般可控制在100厘 米/ 分钟。 确保槽内液体在连续搅拌，搅拌片呈浆状；槽内液体通过 隔膜泵和50目过滤器进行回流。 用Zahn氏杯监控胶粘剂的粘度，必要时添加溶剂；在不使 用生产线时，必须用盖密封槽子。
草酸 10 硫酸 10 水 80 • 水冲洗，干燥。 *30分钟内涂胶 重量份 重量份 重量份
23
Company Confidential
23
黄铜－化学处理方法
• 蒸汽脱脂 • 室温，浸于下述溶液1～3分钟
•
过硫酸铵 25 重量份 水 75 重量份 水洗，干燥，立即涂胶。
24
Company Confidential
24
PTFE表面处理
• 脱脂：丙酮或丁酮 • 在下述溶液（ 25℃ ）中浸渍1～3分钟
金属钠 23g 萘 128g 四氢呋喃（无水） 1L （严格在无水条件下配制，隔绝空气保存） • 丙酮或丁酮清洗，去离子水洗，干燥。
25
Company Confidential
25
尼龙表面处理
• 脱脂：丙酮或丁酮
•
29
Company Confidential
29
ห้องสมุดไป่ตู้
胶粘剂的搅拌
• 搅拌前，首先拿工具将桶底和桶壁的固体刮起，溶入胶粘
• •
剂中。必须避免产生静电火花。 应使用防爆的搅拌设备，推荐20～60rpm的转速，可以防 止过大剪切和气泡，同时确保所有固体成分均匀分散在溶 剂体系中。 用于粘度控制的常用仪器：如Zahn 杯1～4＃，或NK-2岩 田杯。
2
Company Confidential
2
胶粘剂定义
• 一种薄的聚合物涂层，由高聚物，颜料，填料，交联剂 组成并混合在溶剂体系内。 底涂 和基材粘结，防腐蚀，和面涂/胶粘剂粘结
面涂/胶粘剂 和底涂粘结，并和橡胶粘结。
单涂 同时具有底涂和面涂的两种功能。
3
Company Confidential
3
8
Company Confidential
8
第 I 部分 基材的准备
9
Company Confidential
9
基材的种类
• • • • •
磁性金属：冷热轧钢材，电镀钢材，热浸镀钢材 非磁性金属：不锈钢，铝，黄铜，钛，镁，铅。 粉末烧结的金属和各种合金。 塑料材料：尼龙，聚四氟乙烯，聚甲醛等。 纤维：尼龙，聚酯等.
化学处理
底涂使用
填料,转移,注射
干燥
后处理
面涂使用
干燥
7
Company Confidential
7
CH205 操作步骤（试例）
•
• • • • • • • •
表面处理：机械处理(喷砂)后脱脂，或化学处理，以除去加工油，锈或其他氧化层。使 用钢砂（珠）喷普通钢材，铸铁等铁磁性金属，表面处理后可停放时间应控制在再次出 现氧化生锈之前；用石英砂喷不锈钢，铝，黄铜，锌和其他非铁磁性金属，且在表面处 理后90分钟内必须完成涂胶。 搅 拌：在使用之前必须充分搅拌，达到均匀混合后方可使用。 稀 释：可使用丁酮或甲基异丁基稀释CH205，当喷涂使用时，可调至粘度为18－20 秒（Zahn＃2杯）。加稀释剂时应边缓慢加入，边保持搅拌。以防误操作引起沉淀。 涂胶方法：浸渍法、喷涂法、刷涂法、辊涂法、转移法。 涂胶厚度：通常设定CH205干膜厚度在5.1～10.2μm。当单用粘接丁腈胶或与CH220系 列胶粘剂配合时，选用膜厚高限值；其他应用则选用膜厚低限值。 干 燥：涂胶后应在清洁空气中干燥约30～45分钟(室温),使用65－82C鼓风烘箱有利 于更快并彻底烘干涂胶件。 停 放：若涂胶件被妥善存放，隔绝粉尘、油污和水汽等影响，最长甚至可停放一月。 硫 化：当涂胶件被放置于热模中后，应迅速填充橡胶并合模，防止胶粘剂预固化而 失效，以确保胶粘剂和橡胶同时硫化，并获得最佳粘接性能。 硫化时间：取决于胶料硫化时间。