2835规格书
SMD2835灯珠规格书
不良数量 0/50 0/50 0/50 0/50 0/50 0/50 0/50 0/50 0/50
注释 1.所有尺寸单位为毫米。 2.如果无其它注明，公差范围通常采用±0.1 毫米。
建议焊盘尺寸
8
QQ--250884504
8.料盘结构和包装
包装标签
数量
流明值
BIN 区 正向电压
项目 盘 盒 箱
10
QQ--250884504
10.使用注意事项 储存 (1) 打开包装前 在温度不超过 40℃及湿度不超过 90%RH 条件下，LED 可以保存一年，在储存的时候， 建议采用带干燥剂的防潮袋的包装方式。 (2)打开包装后 LED 需要储存在<=40℃＆<=60%RH 相对湿度的条件下，我们强烈建议您从打开包装到 完成贴片整个过程在一个星期内完成。 如果有未使用完的剩余 LED，我们建议重新使用出厂时的防潮剂，并且需要重新密封。 如果干燥剂过期了，请将 LED 放在 70℃烤箱烘烤 12 小时。 LED 电极和引线框架是由表面镀了银的铜合金构成，镀银层会受到来自周围环境的破坏， 请把 LED 远离那种会腐蚀 LED 电极镀银层的环境，LED 电极被腐蚀后，会降低它的焊接 能力和光电参数。 请避免 LED 使用在温度快速变化的环境中，尤其是会发生冷凝的高湿环境中。
CIE-Y 0.4085 0.4057 0.4153 0.4181
Rank
30C03 (2900-3100K)
CIE-X 0.4386 0.4494 0.4554 0.4443
CIE-Y
Rank
CIE-X
0.3818
0.3822
0.3762
40C03 0.3920
0.3888 (3900-4100K) 0.3974
SMD2835白色05W灯珠规格书概论
Life Test:
Affect of Ti on Luminous Maintenance (If=20mA) (Dot line: Expected Life)
Tj=55℃ Tj=85℃ Tj=105℃
Mechanical Dimensions 外观尺寸:Unit 单位(mm)
For reflow soldering 建议焊盘尺寸.
测试条件
符号
Color 颜色
MIN 最小值
Value 参数
TYP 典型值
MAX 最大值
Unit 单位
Forward Voltage 正向电压
If=60mA
Vf
W
3.0
3.4
V
Luminous intensity 亮度
If=60mA
Iv
W
8000
mcd 11000
Wavelength 波长
If=60mA
Reliability:可靠性
1,TESTITEMS AND RESULTS 测试务件和结果
Type
Test Item
Test Conditions
项目
测试项目
测试条件
Note 记录
Number of Damaged 受损数量
Resistance to Soldering
Hest (reflow soldering)
SHENZHEN HEALTH LIGHTING TECH.CO;LTD 深圳市合莱特光电科技有限公司
SPECIFICATIONS 规格书
HLT TOP -2835 SERIES
Customer 客户确认
Approved 批准
Checked 审核
2835贴片规格书
中之光电科技有限公司ZT2835W0M1-****(0.2W)规格书2.8mm Medium Power SMT Hyper White Top LED2.8 mm 中功率贴片反射盖灌注型超亮发光二极管Features 特征• Package Size ：2.8 (L) ×3.5(W) ×0.8 (T) mm封装尺寸： 2.8 (长) ×3.5 (宽) ×0.8 (厚) mm • Silicone Packed采用硅胶封装 •Super long life time超长寿命 •Anti UV 防紫外线•White colors are available in(1800K- 15000K) 可供白光(1800K- 15000K) •High CRI products高显色性产品•Wide viewing angle (2θ1/2=120°) 宽角度 (2θ1/2=120°)Applications 产品应用•Indoor lighting: Fluorescent lamp, tube •室内照明：日光灯管、灯条•Commercial illumination and displays: •商业照明显示：广告字、广告灯箱Advertising words, light box•LCD Backlighting •LCD 背光源 •Decorative lighting: light strip •装饰照明：柔性灯条 •Automotive interior auxiliary lighting•Other illumination and displays •其它照明和显示类OOF a Top View 顶视Side View 侧视OOPart No. Description产品型号说明Color Bin Limit色度代码;(at I F = 60 mA, T a = 25 O C )Color Bin色坐标常用BIN区(Common Bin)可选BIN区（Optional Bin）Typical Electro-Optical Characteristics Curves 典型光-电特性曲线图PACKAGE OUTLINE 外形尺寸 (Units: mm)Recommended Soldering 推荐焊接模式0.8Solder Pad一、PRECAUTONS IN USE LED/使用LED注意事项；LED Soldering condition/ LED焊接条件；1：烙铁焊接：烙铁最高30W尖端温度不超过300℃；焊接时不超过3秒；Manual soldering：iron Maximum 30W，iron bit temperature can not over 300 degree；soldering time should not be more than 3 seconds；Cleanout/清洗；当用化学品清洗LED胶体时须特别小心，因为有些化学品对胶体表面有损伤并引起褪色如三氯乙烯、丙酮，可用乙醇擦拭浸渍，时间在常温下不超过2分钟。
everlight 2835规格书
SMD Low Power LED67-21S/LK2C-HXXXXXXXXB2Z6/2TFeatures‧PLCC-2 packageTop view‧white LED˙High luminous intensity output˙Wide viewing angle˙Pb-free˙RoHS compliantDescriptionThe Everlight 67-21S package has high efficacy, high CRI, low power consumption, wide viewing angle and a compact form factor. These features make this package an ideal LED for all lighting applications.ApplicationsGeneral lighting‧Decorative and Entertainment Lighting‧Indicators‧Illumination‧Switch lights‧Product Number Explanation67–21S / L K 2 C – H XX XX XX XX XX / 2TBin Group of Forward VoltageBin Group of Max. Luminous FluxBin Group of Min. Luminous FluxMax. Color temperatureMin. Color temperatureBin Code of Color Rendering Index Table of Color Rendering IndexSymbol DescriptionM CRI(Min.) : 60N CRI(Min.) : 65L CRI(Min.) : 70Q CRI(Min.) : 75K CRI(Min.) : 80P CRI(Min.) : 85H CRI(Min.) : 90Note:Tolerance of Color Rendering Index: ±2Example:67-21S/LK2C-H3030M3N4B2Z6/2TCRI 70(Min.)CCT 3000KFlux 20~33lmV F 2.9~3.6VI F60mAMass Production ListProductCRIMin.(1)CCT(K)Φ(lm)Min. (2)Φ(lm)Max. (2)67-21S/LK2C-H2727M3N4B2Z6/2T 70 2700K 19 33 67-21S/LK2C-H3030M3N4B2Z6/2T 70 3000K 20 33 67-21S/LK2C-H4040M4N4B2Z6/2T 70 4000K 21 33 67-21S/LK2C-H5050M4N4B2Z6/2T 70 5000K 22 33 67-21S/LK2C-H5757M4N4B2Z6/2T 70 5700K 22 33 67-21S/LK2C-H6565M4N4B2Z6/2T 70 6500K 22 33Note:1. Tolerance of Color Rendering Index: ±22. Tolerance of Luminous flux: ±11%.Device Selection GuideChipMaterialsEmitted Color Resin ColorInGaNCool WhiteNeutral WhiteWarm WhiteWater ClearAbsolute Maximum Ratings (T Soldering=25℃)Parameter Symbol Rating Unit Forward Current I F75 mA Peak Forward Current (Duty 1/10 @10ms) I FP100 mA Power Dissipation P d270 mW Operating Temperature T opr-40 ~ +85 ℃Storage Temperature T stg-40 ~ +100 ℃Thermal Resistance (Junction / Soldering point) R th J-S50 ℃/W Junction Temperature T j125 ℃Soldering Temperature Tsol Reflow Soldering : 260 ℃ for 10 sec. Hand Soldering : 350 ℃ for 3 sec.Note:The products are sensitive to static electricity and must be carefully taken when handling productsElectro-Optical Characteristics (T Soldering=25℃)Parameter Symbol Min. Typ. Max. Unit ConditionLuminous Flux(1)Φ19 ----- 33 lm I F=60mA Forward Voltage(2)V F 2.9 ----- 3.6 V I F=60mA Color Rendering Index(3)Ra 70 ----- ----- I F=60mA Viewing Angle 2θ1/2----- 120 ----- deg I F=60mA Reverse Current I R----- ----- 50 µΑ V R =5VNotes:1. Tolerance of Luminous flux: ±11%.2. Tolerance of Forward Voltage: ±0.1V.3. Tolerance of Color Rendering Index: ±2Bin Range of Luminous FluxBin Code Min.Max.Unit ConditionM3 19 21 lm I F =60mAM4 21 24 N3 24 27 N42733Note:Tolerance of Luminous flux: ±11%.Bin Range of Forward VoltageGroupBin CodeMin. Max. Unit ConditionB236 2.9 3.0 V I F =60mA37 3.0 3.1 383.1 3.2 39 3.2 3.3 40 3.3 3.4 41 3.4 3.5 423.53.6Note:Tolerance of Forward Voltage: ±0.1V.The C.I.E. 1931 Chromaticity DiagramBin Range of Chromaticity CoordinatesCCT Bin Code CIE_x CIE_y Bin Code CIE_x CIE_y2700K 27K-A0.4813 0.431927K-D0.4700 0.41260.4687 0.4289 0.4627 0.41090.4621 0.4169 0.4588 0.40410.4667 0.4180 0.4544 0.40300.4627 0.4109 0.4483 0.39190.4700 0.4126 0.4593 0.3944Reference Range:2580K~2700K27K-B0.4687 0.428927K-C0.4465 0.40710.4562 0.4260 0.4373 0.38930.4465 0.4071 0.4483 0.39190.4539 0.4088 0.4544 0.40300.4576 0.4158 0.4502 0.40200.4621 0.4169 0.4539 0.4088Reference Range:2700K~2870K27K-F0.4667 0.418027K-G0.4627 0.41090.4576 0.4158 0.4539 0.40880.4539 0.4088 0.4502 0.40200.4627 0.4109 0.4588 0.4041Reference Range: 2665K~2770KCCT Bin Code CIE_x CIE_y Bin Code CIE_x CIE_y3000K 30K-A0.4562 0.426030K-D0.4465 0.40710.4430 0.4212 0.4388 0.40430.4375 0.4096 0.4355 0.39770.4422 0.4113 0.4311 0.39620.4388 0.4043 0.4259 0.38530.4465 0.4071 0.4373 0.3893Reference Range:2870K~3000K30K-B0.4430 0.421230K-C0.4221 0.39840.4299 0.4165 0.4147 0.38140.4221 0.3984 0.4259 0.38530.4297 0.4011 0.4311 0.39620.4328 0.4079 0.4267 0.39460.4375 0.4096 0.4297 0.4011Reference Range:3000K~3220K30K-F0.4422 0.411330K-G0.4388 0.40430.4328 0.4079 0.4297 0.40110.4297 0.4011 0.4267 0.39460.4388 0.4043 0.4355 0.3977Reference Range:2960K~3080KThe C.I.E. 1931 Chromaticity DiagramBin Range of Chromaticity CoordinatesCCT Bin Code CIE_x CIE_y Bin Code CIE_x CIE_y4000K 40K-A0.4006 0.404440K-D0.3952 0.38800.3871 0.3959 0.3873 0.38310.3843 0.3858 0.3854 0.37680.3890 0.3887 0.3810 0.37410.3873 0.3831 0.3784 0.36470.3952 0.3880 0.3898 0.3716Reference Range:3700K~3970K40K-B0.3871 0.395940K-C0.3703 0.37260.3736 0.3874 0.3670 0.35780.3703 0.3726 0.3784 0.36470.3779 0.3773 0.3810 0.37410.3793 0.3828 0.3764 0.37130.3843 0.3858 0.3779 0.3773Reference Range:3970K~4270K40K-F0.3890 0.388740K-G0.3873 0.38310.3793 0.3828 0.3779 0.37730.3779 0.3773 0.3764 0.37130.3873 0.3831 0.3854 0.3768Reference Range:3870K~4080KThe C.I.E. 1931 Chromaticity DiagramBin Range of Chromaticity CoordinatesCCT Bin Code CIE_x CIE_y Bin Code CIE_x CIE_y5000K 50K-A0.3551 0.376050K-D0.3533 0.36240.3464 0.3688 0.3482 0.35830.3456 0.3604 0.3477 0.35300.3487 0.3629 0.3448 0.35070.3482 0.3583 0.3441 0.34280.3533 0.3624 0.3515 0.3487Reference Range:4745K~5000K50K-B0.3464 0.368850K-C0.3371 0.34930.3376 0.3616 0.3366 0.33690.3371 0.3493 0.3441 0.34280.3422 0.3533 0.3448 0.35070.3425 0.3579 0.3418 0.34830.3456 0.3604 0.3422 0.3533Reference Range:5000K~5310K50K-F0.3487 0.362950K-G0.3482 0.35830.3425 0.3579 0.3422 0.35330.3422 0.3533 0.3418 0.34830.3482 0.3583 0.3477 0.3530Reference Range:4910K~5120KCCT Bin Code CIE_x CIE_y Bin Code CIE_x CIE_y5700K 57K-A0.3376 0.361657K-D0.3371 0.34930.3292 0.3539 0.3321 0.34470.3292 0.3464 0.3320 0.34010.3321 0.3490 0.3293 0.33770.3321 0.3447 0.3294 0.33060.3371 0.3493 0.3366 0.3369Reference Range:5310K~5700K57K-B0.3292 0.353957K-C0.3215 0.33530.3207 0.3462 0.3222 0.32430.3215 0.3353 0.3294 0.33060.3262 0.3395 0.3293 0.33770.3261 0.3436 0.3263 0.3350.3292 0.3464 0.3262 0.3395Reference Range:5700K~6020K57K-F0.3321 0.349057K-G0.3321 0.34470.3261 0.3436 0.3262 0.33950.3262 0.3395 0.3263 0.33500.3321 0.3447 0.3320 0.3401Reference Range:5520K~5780KCCT Bin Code CIE_x CIE_y Bin Code CIE_x CIE_y6500K 65K-A0.3205 0.348165K-D0.3213 0.33710.3117 0.3393 0.3161 0.33200.3125 0.3328 0.3166 0.32810.3157 0.3360 0.3136 0.32510.3161 0.3320 0.3145 0.31870.3213 0.3371 0.3221 0.3261Reference Range:6020K~6500K65K-B0.3117 0.339365K-C0.3048 0.32090.3028 0.3304 0.3068 0.31130.3048 0.3209 0.3145 0.31870.3100 0.3259 0.3136 0.32510.3093 0.3297 0.3106 0.32220.3125 0.3328 0.31 0.3259Reference Range:6500K~7050K65K-F0.3157 0.336065K-G0.3161 0.33200.3093 0.3297 0.3100 0.32590.3100 0.3259 0.3106 0.32220.3161 0.3320 0.3166 0.3281Reference Range:6300K~6690KNote:1. The value is based on driving current by 60mA.Spectrum DistributionTypical Electro-Optical Characteristics CurvesTj - Junction Temperature (oC)015304560750.00.20.40.60.81.01.21.4R e l a t i v e L u m i n o u s I n t e n s i t yForward Current(mA)Typical Electro-Optical Characteristics Curves25405570851001150.00.20.40.60.81.01.2Tj - Junction Temperature ( oC )R e l a t i v e L u m i n o u s F l u x2.62.7 2.8 2.93.0 3.11530456075TS=25CI F -F o r w a r d C u r r e n t (m A )V F - Forward V oltage (V )020*********20406080100F o r w a r d C u r r e n t (m A )Soldering Tem perature (oC )0.70.80.91.080°90°50°60°70°40°20°0°10°30°Package DimensionNote:Tolerance unless mentioned is ±0.1 mm; Unit = mmMoisture Resistant Packing MaterialsLabel Explanation‧CPN: Customer’s Product Number ‧P/N: Product Number ‧QTY: Packing Quantity‧CAT: Luminous Intensity Rank ‧HUE: Dom. Wavelength Rank ‧REF: Forward Voltage Rank ‧LOT No: Lot NumberReel DimensionsNote:Tolerances unless mentioned ±0.1mm. Unit = mmCarrier Tape Dimensions: Loaded Quantity 250/500/1000/2000 pcs Per ReelNote:1.Tolerance unless mentioned is ±0.1mm; Unit = mmMoisture Resistant Packing ProcessLabel Desiccant LabelPrecautions for Use1. Over-current-proofCustomer must apply resistors for protection; otherwise slight voltage shift will cause big current change (Burn out will happen).2. Storage2.1 Do not open moisture proof bag before the products are ready to use.2.2 Before opening the package: The LEDs should be kept at 30℃or less and 90%RH or less.2.3 After opening the package: The LED's floor life is 168 Hrs under 30℃ or less and 60% RH or less. If unusedLEDs remain, it should be stored in moisture proof packages.2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time,baking treatment should be performed using the following conditions.Baking treatment: 60±5℃for 24 hours.3. Soldering Condition3.1 Pb-free solder temperature profile260 Max.Above255 C C3.2 Reflow soldering should not be done more than two times.3.3 When soldering, do not put stress on the LEDs during heating.3.4 After soldering, do not warp the circuit board.4. Soldering IronEach terminal is to go to the tip of soldering iron temperature less than 350℃for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder.5. RepairingRepair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.。
led灯珠型号型号对照表2835，贴片led灯珠型号对照表2835参数有哪些？
led灯珠型号型号对照表2835，贴片led灯珠型号对照表2835参数有哪些？展开全文led灯珠型号型号对照表2835，贴片led灯珠型号对照表2835参数有哪些？五一期间，有读者在灯珠教授后台留言，问 : led灯珠型号对照表2835，贴片led灯珠型号对照表2835参数有哪些？我们今天就来看看led灯珠型号对照表2835和贴片led灯珠型号对照表2835参数。
led灯珠型号对照表28352835贴片灯珠参数1、2835灯珠尺寸: 2.8mm（长）X 3.5mm（宽） X 0.8mm（厚）2、2835灯珠灯珠功率，单颗0.2瓦， 0.5瓦和单颗1瓦 (单颗3瓦需定做)3、2835灯珠电压: 白光，翠绿光，蓝光和紫光，电压为2.8-3.4伏左右。
2835红光，普绿光，橙光和黄光，电压是1.8-2.5伏左右。
4、2835灯珠角度，常规是120度，特殊可以做60度等聚光小角度。
5、2835常规的电压白光3伏左右，高压2835灯珠可以做6伏，9伏，18伏和36伏等高压2835灯珠。
6、2835灯珠规格型号多，亮度可定做，价格有优势，亮度参数可根据需求定做。
贴片led灯珠型号对照表2835参数2835灯珠白光色温参数 :1、金黄光 1600K-2000K,2、暖白光2800K-3200K,3、中性白光 3800-4300K ,4、标准白光 6000-6500K,4、冷白光 7000K以上到100000k。
2835贴片灯珠颜色: 2835红光，2835蓝光，2835黄绿光，2835橙光，2835灯珠黄光，2835灯珠紫光，2835灯珠红外灯。
今天的，led灯珠型号对照表2835，贴片led灯珠型号对照表2835参数就分享到这里吧。
2835灯珠目前在通用照明市场上运用是相当广泛的一个贴片灯珠型号。
如果你需要更多的2835灯珠规格型号表或参数，灯珠规格书，可以咨询2835灯珠厂家台宏光电客服工程师。
灯珠规格书里面2835灯珠功率参数，规格，型号，功率，电压，焊盘尺寸图都是有的。
宏齐光电子(深圳)有限公司 2835自然白规格书
二、外形尺寸及建议焊盘尺寸：
①
②
①
Polarity
②
推荐焊盘尺寸：
① ②
②
②
① ②
注:
1. 单位 : 毫米（mm） ； 2. 公差 ：如无特别标注则为± 0.10 mm；
HARVATEK OPTO-ELECTRONICS(SHENZHEN)CO., LTD.
0.4033 0.406 0.394 0.3916 0.4006 0.4033 0.3916 0.3893 0.3979 0.4006 0.3893 0.3869 0.3952 0.3979 0.3869 0.3846 0.3925 0.3952 0.3846 0.3822 0.3897 0.3925
符 号
Pd IFP IF VR Topr Tstg Tsol ESD
最大额定值
180 80 60 5 -30°C -40°C ~ ~ + 85°C + 90°C
单 位
mW mA mA V
回流焊 : 260°C ，10s 手动焊 : 300°C ，3s 2000 V
五、光电参数
参数 光通亮 显指 半光强视角 色坐标 色温 正向电压 反向电流
发布日期 2014.02.25 页码
8 of 13
八、标签标识：
CAT：光强 （单位（mcd） ） HUE：色坐标 REF：电压 （单位（V） ）
九、包装载带与圆盘尺寸：
φ 13.0
注:
1、 尺寸单位为毫米(mm)； 2、 尺寸公差是±0.1mm；
HARVATEK OPTO-ELECTRONICS(SHENZHEN)CO., LTD.
宏齐光电子（深圳）有限公司
HARVATEK OPTO-ELECTRONICS(SHENZHEN)CO., LTD.
2835冷白灯珠(60mA-0.2W) 中文规格书
深圳市鑫冠明科技有限公司产品规格书2835WOM1深圳市鑫冠明科技有限公司目录1.产品描述2.最大额定值3.光电参数4.典型光电特性曲线5.分光标准6.可靠性测试7.产品规格尺寸8.料盘结构和包装9.回流焊10.使用注要事项深圳市鑫冠明科技有限公司1.产品描述特性◆发光角度：120度◆小尺寸：2.8mm*3.5mm*0.80mm◆符合RoHS标准无铅焊接深圳市鑫冠明科技有限公司◆高流明高光效典型应用◆背光源◆日光灯◆室内室外照明◆建筑/装饰照明◆广告字、广告灯箱材料物料项目类型支架底部PPA与金属散热片结合支架外壳耐热聚合物封装树脂硅树脂电极镀银铜合金固晶材料导热硅胶芯片材料德豪润达11*182.最大额定值=25℃参数符号数值单位消耗功率200 mW 正向电流60 mA3.光电参数参数符号等级 条件最小 最大 单位输出流明L1 =60mA 20 22 lmL2 22 24 L3 24 26 L4 26 28 正向电压V1 =60mA 3.0 3.2 V V23.2 3.4 发光角度 - =60mA 118 123 deg 显色指数-=60mA6285-公差: :±0.03V,:±2%,Ra:±24.典型光电特性曲线反向电压 5 v 工作温度范围 -20~+85 ℃ 储存温度范围 -35~+85 ℃ 脉冲正向电流 300 mA 抗静电能力ESD2000(HBM)V深圳市鑫冠明科技有限公司光谱图深圳市鑫冠明科技有限公司5.分光标准色度图(ANSI C78.377A)深圳市鑫冠明科技有限公司◆Bin区分布2700KRank CIE-X CIE-Y Rank CIE-X CIE-Y27C01 (2600-2800K) 0.44810.415227C02(2600-2800K)0.45830.424 0.45370.40310.4640.4116 0.4640.41160.47440.4204 0.45830.4240.46850.43293000KRank CIE-X CIE-Y Rank CIE-X CIE-Y Rank CIE-X CIE-Y30C01 (2900-3100K) 0.4271 0.39930C02(2900-3100K)0.44940.415330C03(2900-3100K)0.43860.4181 0.4373 0.3964 0.44940.41530.44940.4153 0.4433 0.4057 0.44940.41530.45540.4246 0.4328 0.4085 0.43860.41810.44430.42764000KRank CIE-X CIE-Y Rank CIE-X CIE-Y Rank CIE-X CIE-Y40C01 (3900-4100K) 0.37080.371240C02(3900-4100K)0.37600.381840C03(3900-4100K)0.38220.3945 0.38120.36600.38590.37620.39200.3888 0.38590.37620.39200.38880.39740.4002 0.37600.38180.38220.39450.38790.40615000KRank CIE-X CIE-Y Rank CIE-X CIE-Y50C01 (5000-5300K) 0.3350.351850C02(4700-5000K)0.34440.367 0.33790.33970.34690.3542 0.34690.35420.35580.3688 0.34440.3670.35390.38246500KRank CIE-X CIE-Y Rank CIE-X CIE-Y Rank CIE-X CIE-Y深圳市鑫冠明科技有限公司60C01 (6500-7000K) 0.30170.319260C02(6000-6500K)0.31040.335360C03(5700-6000K)0.32030.3531 0.30640.31240.31460.32710.32390.3428 0.31460.32710.32390.34280.32750.3500 0.31040.33530.32030.35310.32360.35916. 可靠性测试测试项目测试条件测试周期不良数量冷热冲击=-40℃(30分钟) ~ 100℃ (30分钟)100 循环0/50高温储存=100℃1000小时0/50高温高湿储存=60℃, RH=90%1000小时0/50低温储存=-40℃1000小时0/50常温老化=25℃, =60mA1000小时0/50高温老化=80℃, =60mA1000小时0/50低温老化=-40℃, =60mA1000小时0/50抗静电测试2KV 3次0/50回流焊250℃< 10sec.3次0/50 7.产品规格尺寸注释深圳市鑫冠明科技有限公司1.所有尺寸单位为毫米建议焊盘尺寸。
SMD2835白色0.5W灯珠规格书
Tsld:260·C
2tines
0/20
回流焊
Thermal Shock 冷热冲击
-40·C 15min
100cgde
0/20
100·C15min
High Temperature 高低温循环
Ta:100·C
1000hrs
0/20
Environmental sequence
Low Temperature 低温测试
Applications Channel letter Decorative Lighting
应用 指示 装饰 照明
Absolute maximum ratings 最大限定参数(Ta-25·C)
Parameter 项目名称
Symbol 符号
Value 叁数
Unit 单位
Power dissipation 功率 Forward current 正向电流 Reverse Voltage 反向电压 Operating temperature range 工作温度范围 Storage temperature 存储温度范围 Pulse Forward Current 正向脉冲电流 Electrostatic Discharge 静电防护 Junction temperature 结温
SHENZHEN HEALTH LIGHTING TECH.CO;LTD 深圳市合莱特光电科技有限公司
SPECIFICATIONS 规格书
HLT TOP -2835 SERIES
Customer 客户确认
Approved 批准
Checked 审核
Prepared 编制
Features .Size(mm)3.5*2.8*0.8 .Viewing angle 120° .ROHS compliant lead-free soldering Compatible .White color (2835-0.5W)
2835规格书
●Customer:T e c h n i c a l D a t a S h e e tTOP View White LED (2835)For:IF=60mAContents1. Features2. Applications3. Package outline dimension4. Absolute maximum ratings5. Electrical-optical characteristics6. Tapping specifications7. Package method8. BIN code description9. BIN range10. Reliability test items and conditions11. Precautions for use12. Hazard substance analysisCustomer confirm ApprovedbyIssuedby※Features:1. Package: 3.5*2.8*0.75mm (TOP view white LED)2. Emitted Color: White3. Mono-color type4. Soldering methods: All SMT assembly methods5. Comply ROHS standard.※Applications:1. LCD back light.2. Mobile phones: LCD,3. Status indicators: Consumer & industrialelectronics.4.General use.※→Package Outline Dimension:NOTES:1.All dimensions are in millimeters (inches).2.Tolerance is ±0.10mm unless otherwise specified.3.Specifications are subject to change without notice.※ Absolute Maximum Ratings(Ta=25℃)Parameter SymbolRatingUnit Power Dissipation Pd240mWForward CurrentI F 60 mAPeak Forward Current ＊1 I FP 240mA Reverse Voltage V R 5 V Operating Temperature Topr -30℃~85℃ - Storage Temperature Tstg -40℃~85℃ - Electrostatic dischargeESD2000V＊1 I FP condition: pulse of 1/10 duty and 0.1ms width.※ Electrical-optical characteristics(Ta=25℃)Parameter Symbol Min. Typ. Max. Unit ConditionForward Voltage Vf 3.0 3.4 V Luminous Intensity Lm 20 23 lm Luminous Intensity Iv65007500mcdColor temperatureCT 3900 4500 K Viewing Angle 2θ1/2 - 120 degI F =60mAReverse CurrentI R - 10 μA VR =5VNote: 1. Tolerance of luminous intensity is ±10%2.Tolerance of forward voltage is ±0.05V色区、色温对照表色区典型CIE坐标色温范围(K) 推荐色区备注WA0.3710.391WB0.3670.371√ 4200KWC 0.3720.3423800-4500WD0.3920.407WE0.3850.3843900KWF 0.3780.3633700-4100WG0.4160.424WH0.4050.397 3500KWI 0.3950.3733400-3700WJ0.439 0.436WK0.4280.4093000K,暖白WL 0.4150.3823000-3400WM0.4670.448WN0.452 0.419 2700KWO 0.4340.3882700-3000WP0.4910.457WQ0.4750.4292500KWR 0.4550.3992500-2700※BIN rangeLuminous intensity (tolerance is ±10%@ If=60mA):BIN CODEMin. (mcd)Max. (mcd)15 5500 6500 16 6500 7500 1775008500※ Forward voltage (tolerance is ±0.05V@If=60mA):BIN CODEMin.(v)Max.(v)7-1 3.0 3.17-2* 3.1 3.2 8-1* 3.2 3.3 8-2* 3.3 3.49-1* 3.4 3.5 9-2*3.53.6※ Reliability test items and conditions:No.Test Item Test ConditionsSample sizeAc/Re1 Operation Life Test If=DC60mATemp: Room temperatureTest time=1000hrs 22 0/12 High Temperature High HumidityTemp. =+85℃RH=85%HRTest time=1000hrs22 0/13 Thermal Shock -35℃ ~ +85℃20min 10s 20minTest Time=300cycles22 0/1 4High Temperature Storage High Temp. =+85℃ Test time=1000hrs22 0/1 5Low TemperatureStorage Low Ta=-35℃ Test time=1000hrs22 0/1 6 Temperature Cycle -35℃ ~ +100℃15min 5min 15minTest Time=300cycle 22 0/1 7 Reflow SolderingOperation heating ：245℃(Max.), within 10seconds. (Max.) 22 0/1※ Judgment criteria of failure for the reliability·Iv: Below 50% of initial values ·Vf: Over 20% of upper limit value ·IR: Over 2 times of upper limit valueNote: Measurement shall be taken between 2 hours and after the test LED have been returned to normal ambient conditions after completion of each test.※ Precautions for use :1. Customer must apply the current limiting resistor in the circuit so as to drive the LEDs within therated current. Otherwise slight voltage shift maybe will cause big current change and burn out will happen.2. Also, caution should be taken not to overload the LEDs with instantaneous high voltage at theturning ON and OFF of the circuit. 3. Storage:3.1 Don’t open the moisture proof bag before ready to use the LEDs.3.2 The LEDs should be kept at 30℃ or less and 60%RH or less before opening the package. The max. storage period before opening the package is 1 year.3.3 After opening the package, the LEDs should be kept at 30℃/35%RH or less, and it shouldbe used within 7 days.3.4 If the LEDs be kept over the conditions of 3.4, baking is required before mounting. Bakingcondition as below: 75±5℃ for 24 hrs. 4. Soldering condition: 4.1 Manual of soldering ：The temp. of the iron should be lower than 230℃ and soldering within 3sec per solder-pad isto be observed.4.2 Pb-free solder temp. –time profileNote: a) Reflow soldering should not be done more than two times. b) Don’t put stress on the LEDs when soldering.c) Don’t warp the circuit board before it have been returned to normal ambientconditions after soldering.Loaded quantity: 3000 pcs/reel ※Package Method:(unit:mm)。
2835双色灯珠规格书
2835双色灯珠规格书今天咱们来好好唠唠2835双色灯珠。
这2835双色灯珠啊，可真是个有趣的小玩意儿呢。
一、尺寸大小。
这个灯珠的尺寸是很有讲究的哦。
它的长大概是2.8毫米，宽呢是3.5毫米，所以才叫2835啦。
这个大小在众多灯珠里算是比较小巧玲珑的。
就像一个小小的精灵，虽然小，但是本事可不小呢。
它这么小的尺寸，在很多地方都能派上用场。
比如说一些小型的灯具，像那种精致的小夜灯，它就能够完美地适配。
因为小夜灯不需要很大的灯珠，2835双色灯珠放进去刚刚好，既不会占太多空间，又能发出很温馨的光。
二、颜色组合。
说到双色，那可就太好玩啦。
它可以有各种各样的颜色组合呢。
常见的有暖白色和正白色的组合。
暖白色就像是冬日里的暖阳，照在身上暖洋洋的，特别适合营造那种温馨的氛围，像在家里的卧室里，用这种颜色组合的灯珠，一打开灯，整个房间就充满了家的温暖感觉。
正白色呢，就比较明亮，像白天的阳光，很清澈。
这种颜色组合在一些需要不同照明效果的地方就特别有用。
比如说在客厅，看电视的时候可以用暖白色，看书或者做其他事情的时候就可以切换到正白色，超级方便的。
还有些2835双色灯珠是红色和绿色的组合。
这就很适合在一些有创意的灯具上啦，比如说那种可以变换颜色来营造节日氛围的彩灯。
在圣诞节的时候，红色和绿色一亮起来，圣诞的气息就扑面而来啦。
或者在一些酒吧之类的地方，这种颜色组合也能制造出很酷炫的灯光效果呢。
三、亮度和功率。
这2835双色灯珠的亮度也是很可观的哦。
虽然它小，但是它的发光效率可高了。
一般来说，它的功率不会太大，这样就比较节能。
它的亮度能够满足我们日常的很多照明需求。
就拿刚刚说的小夜灯来说，它不需要太亮，2835双色灯珠的亮度既能让你在夜里看清周围的环境，又不会刺眼。
在一些需要节能又要保证一定亮度的场所，像一些商场的装饰灯，用2835双色灯珠就再合适不过了。
它在较低的功率下能发出足够的光，既节省了电费，又达到了照明或者装饰的效果。
18V30MA2835规格书
产品规格书SPECIFICATION Customer/客户名称：Part NO./ 产品型号：Description /产品描述：18V30MA2835灯珠Deliver date/送样日期：Address/地址：深圳市宝安7区宝民一路64号华丰甲岸商务中心509室Tel/电话：86-755-33590659 Fax/传真：86-755-61605425E-mail: lizy@网址：产品编码规则X1：深圳市高芯照明技术有限公司X2：HV （高芯的品牌）X3：5054，5730，2835，3014，3030，5050X4：D （4700K-7000K ）， N （3500-4700K ）W （2600K-3500K ）X5: A （RA>70）,B(RA>80),C(RA>85),D(RA>90)X6：03（3-3.3V ）， 06（6-6.6V ）, 09 (9-10V), 12 (12-13.2V), 15(15-16.5V),18(17.8-20V), 36(35-37V)X7：A （0.06W ）， B （0.1W ）， C(0.2W)， D （0.3W ）， E （0.4W ）， F(0.5W)，G （0.55W ），H （1W）Outline Dimensions 尺寸轮廓Recommended Soldering Pattern (Units:mm;Tolerance:+/-0.1) 焊盘规格Note:1.All dimensions are in millimeters所有的尺寸单位都是毫米2.Scale none 无比例3.This tolerances of drawer are for reference 此尺寸图之公差仅供参考Caution：Don't suggest several welding 不建议进行多次焊接Absolute Maximum Rating at Ta=25℃(最大绝对参数)Notes:1.1/10 Duty Cycle,0.1ms Push Width2.1.29mm below package bash3.ESD(HBM) : Class I:0-1999V ; Class II:2000-3999V; Class III:4000-8000V■Typical Optical/Electrical Characteristics at Ta=25℃Notes:1.Metal Core PCB is mounted on the heat Fins 需安装在金属基板上来保证良好散热2.Tolerance of measurement of forward voltage±0.2V 电压测试误差±0.2V3. Tolerance measurement of x/y ±0.01 色坐标±0.014. Tolerance measurement of luminous intensity / luminous flux+/-5% 发光强度/光通量测试误差±10%Typical CharacteristicsTypical Electrical/Optical Characteristic Curves (25°C Ambient Temperature)Reliability Test Items and Conditions 可靠性试验Criteria for Judging The Damage 失效判断标准U.S.L.* : Upper Standard Level 高标准水平L.S.L.** : Lower Standard Level 低标准水平Precaution for use使用注意事项1.储存Storage1.1本产品使用密封防潮静电袋包装，并附有干燥剂及湿度卡This product use sealing moisture electrostatic bag packaging, and with desiccant and humidity card1.2产品须存放在温度≤30℃，湿度≤60%环境中，开封后，应该在24H（1天）内使用完。
led2835灯珠参数（led2835灯珠参数功率电压如何区分）？
led2835灯珠参数（led2835灯珠参数功率电压如何区分）？led2835灯珠参数，led2835灯珠参数功率电压如何区分？led2835灯珠参数，led2835灯珠参数功率电压，led2835灯珠参数功率电压如何区分?是不是现在你选择2835灯珠，⽐较关注2835灯珠的功率电压？是不是功率电压规格型号太多了，你不知道如何区分？我教你⼀招，只要咱们先确认光⾊就可以快速知道。
咱们⽤常规的2835⽩光，功率就是0.2W,0.5W和1W的。
你想想你是要哪⼀个功率的，然后确认⼀下是要2835灯珠⽩光还是彩光的电压。
昨天灯珠教授公号上有个读者问我，2835灯珠参数。
我告诉他，2835灯珠有3种功率，如果是⽩光灯珠，如果看参数表就好。
彩光灯珠的也是。
led2835灯珠参数:2835灯珠参数，主要是功率有3种，单颗0.2⽡，0.5⽡和单颗1⽡。
2835灯珠⽩光有⾦黄光 1600K-2000K, 暖⽩光2800K-3200K, 中性⽩光 3800-4300K ,标准⽩光 6000-6500K, 冷⽩光 7000K以上到100000k。
2835灯珠参数功率电压，常规⽩光是3V, ⾼压有6V，9V,18V, 36V等。
2835灯珠分2835灯珠红光，2835灯珠绿光，2835灯珠蓝光，2835灯珠紫光和2835红外灯等。
2835灯珠尺⼨参数是:2.8X3.5X0.8mm (厚度)。
2835灯珠规格型号⼀览表:2835灯珠参数表:2835灯珠图⽚:2835灯珠规格书。
2835灯珠规格型号多，各种颜⾊品种齐全，功率参数，规格，型号，功率，电压，电流，这些参数电压了解了，亮度了解了，还要找LED灯珠⼚家要⼀些灯珠样品先测试。
光⾊，波长，亮度，⼀致性通过了，再采购，是⽐较实在的做法。
读者有时候关注2835灯珠参数是⼲什么呀？搞灯珠选型，但是有时候显指达不到要求，亮度达不到要求，⼀致性达不到要求，反反复复测试样品，反⽽增加了测试和选型时间。
2835 0.2w 940nm规格书90度 缺口为正极
产品规格书ZT2835IRM1-94090度钻光杨小姐：一叁叁一陆捌玖贰捌贰柒一、外形圖Outline dimensions：焊盘建议大小Recommended size of pad焊点结构Pad Configuration：焊点Pad 功能Function1 正极Anode2 负极Cathode注释:1.所有尺寸单位为毫米所用尺寸單位為毫米2.如果无其它注明，公差范围通常采用±0.1毫米。
二、光電參數Photoelectricity Parameter（環境溫度Ambient temperature：25℃濕度humidity：RH60%）備註：亮度測試公差±15%、波長測試公差±1nm、正向電壓測試公差±0.05V Remark：The tolerance of intensity:±15%, The tolerance of wave length:±1nm,The tolerance of forwards voltage: ±0.05V. Only reference for above data when testing.三、極限參數Absolute Maximum Rating（環境溫度Ambient temperature：25℃濕度humidity：RH60%）四、典型光電特性曲線圖Typical photoelectricity characteristic curve chart LED光强分布曲线(100mA测试)Intensity distribution curve (100mA test)：五、可靠性實驗項目Reliability Test Project ●判斷標準Judging criterion:六、儲存(1) 打開包裝前在溫度不超過40℃及濕度不超過90%RH條件下，LED可以保存一年，在儲存的時候，建議採用帶乾燥劑的防潮袋的包裝方式。
2835(sw)规格书
LifecyclePhase:
Expired Period: Forever
DATASHEET SMD Low Power LED
67-21S/KK2C-HXXXXXXXX2934Z6/2T(SW) Mass Production List
Product 67-21S/KK2C-H3030M31N42934Z6/2T(SW) 67-21S/KK2C-H4040M4N42934Z6/2T(SW) 67-21S/KK2C-H6565M41N42934Z6/2T(SW) Notes: 1. Tolerance of Color Rendering Index: ±2 2. Tolerance of Luminous flux: ±11%. CRI Min.(1) 80 80 80 CCT(K) 3000K 4000K 6500K Φ(lm) Min. (2) 20 21 22 Φ(lm) Max. (2) 33 33 33
Bin Group of Forward Voltage Bin Group of Max. Luminous Flux Bin Group of Min. Luminous Flux Max. Color temperature Min. Color temperature Bin Code of Color Rendering Index
Parameter Luminous Flux(1) Forward Voltage(2) Color Rendering Index(3) Viewing Angle Reverse Current Symbol Min. 20 2.9 80 ---------
)
Typ. ------------120 ----Max. 33 3.4 --------50 deg Unit lm V Condition
led2835绿光规格书
led2835绿光规格书2835GREEN SPECIFICATION产品型号 Model NO.:YLT-led2835GC-520描述:2835绿光贴片发光二极管是行业内标准的封装产品，此类产品为高可靠性及应用范围非常广泛，此高可靠性的产品非常适用于半户外及户外灯具相关,高可靠性要求的应用场合。
特性:1.外形尺寸D imensions单位(Units):毫米(mm)2.光电特性Electrical / Optical characteristics1/10周期, 0.1 msec脉宽IFP Conditions : 1/10 Duty Cycle, 0.1 msec Pulse Width.½ Rja = Heat resistance from Dice to Ambient temperature (Ta) Rjs = Heat resistance from Dice to Solder temperature of Cathode Side (Ts) (3) 原始光电参数Initial Electrical/Optical Characteristics (TA=25ºC)(4)发光强度范围Luminous Intensity Ranking (TA=25ºC)允许误差± 10%Luminous Intensity Measurement allowance is ± 10%.(5)颜色范围Color Ranking (TA=25ºC)允许误差± 0.01Color Coordinates Measurement allowance is ± 0.01.3.包装PACKAGING(1)LEDS在装带之后纸箱包装. The LEDs are packed in cardboard boxes after taping.(2)装带规格Taping Specifications (单位:毫米Units:mm)(3)卷轴尺寸Reel Dimension装带数量2000个/卷2000Pcs/Reel(3) 最小包装标签注明以下:产品名称.批号.光电范围.数量.The label on the minimum packing unit shows ; Part Number, Lot Number, Ranking, Quantity.(4)请注意防水防潮Keep away from wate r, moisture in order to protect the LEDs.(5) 须采取适当防护措施,以防包装箱跌落或受到强力撞击造成对产品的损伤.The LEDS may be damaged if the boxes are dropped or receive a strong impact against them. so precautions must be taken to prevent any damage.4.可靠性RELIABILITY*) U.S.L.：Upper Standard Level **) L.S.L.：Lower Standard Level5.注意事项Cautions(1) 焊接条件Soldering Conditions本产品最多只可回焊两次,且在首次回焊后须冷却至室温之后方可进行第二次回焊.Number of reflow process shall be less than 2 times and cooling process to normal temperature is required between first and Second soldering process. 推荐焊接条件(Recommended soldering conditions)有铅回焊（Lead Solder ）无铅回焊(Lead-Free Solder)推荐焊盘式样(Recommended Soldering Pattern ) 单位:毫米( Units:mm )(2)静电Static Electricity触摸LED时,推荐使用防静电手腕带或防静电手套.It is recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs.所有装置、设备、机器均应接地.All devices, equipment and machinery must be properly grounded.静电损坏的LED会显示出异常特征:正向电压变低或在低电流时死灯.标准: I F=0.5mA时, V F > 2.0VDamaged LEDs will show some unusual characteristics such as the forward voltage becomes lower, or the LEDs do not light at the low current. Criteria : (V F > 2.0V at I F=0.5mA)(3)防潮包装Moisture Proof Package使用防潮包装It is recommended that moisture proof package be used .(4)储藏Storage打开包装袋之前,LED在温度为30°C或更低湿度70%RH以下,可保存一年.Before opening the package ,The LEDs should be kept at 30°C or less and 70%RH or less. The LEDs should be used within a year.（5）打开包装之后,应在24hrs 内焊接完毕.After opening the package, The LEDs should be soldered within 24 hours (1days) after opening the package. If unused LEDs remain, they should be stored in moisture proof packages, such as sealed containers with packages of moisture absorbent material (silica gel).下列情况发生时，须要在焊接前重新烘烤60 ± 5°C,24小时以上。
2835led灯珠规格型号一览表，2835灯珠参数有哪些？
2835led灯珠规格型号一览表，2835灯珠参数有哪些？2835led灯珠规格型号一览表，2835灯珠参数有哪些？一、2835灯珠，2835灯珠参数，是做通用照明用的很多的一个规格型号。
2835led灯珠规格型号一览表，2835灯珠参数有哪些？2835灯珠参数多少伏？2835灯珠参数范围，2835灯珠参数电压，2835灯珠参数和价格？2835灯珠参数是多少？2835灯珠参数几瓦？2835灯珠参数规格书？2835灯珠参数0.2w，高光效2835灯珠参数，2835灯珠参数正负极，高压2835灯珠参数，这些，是读者和客户询问2835灯珠参数常问的问题。
今天，我们就来看看: 2835led灯珠规格型号一览表，2835灯珠参数有哪些？二、我们先来看看: 2835led灯珠规格型号一览表通过这份表，我们可以了解到很多款的2835灯珠，不同功率，不同颜色，甚至不同电压的2835灯珠。
三、2835灯珠参数有哪些？1、2835灯珠单颗功率0.2瓦，0.5瓦和1瓦。
(单颗3瓦需定做)2、2835灯珠尺寸：2.8 （长）×3.5 （宽）×0.8 （厚） mm3、2835灯珠白光有3伏，6伏，9伏，18伏，36伏高压灯珠4、2835灯珠4000颗每盘。
5、更多参数详细见2835灯珠规格书。
颜色品种齐全，功率参数，规格，型号，功率，电压，电流，这些参数电压。
四、2835灯珠规格书2835灯珠白光，2835灯珠红光，2835灯珠蓝光，2835灯珠黄光，2835灯珠绿光等。
总的来说：2835灯珠应用极广，2835led灯珠规格型号一览表，2835灯珠参数有哪些？更多的是让我们从功率，颜色，电压方面去选型。
其实，更多的2835灯珠参数，还可以从亮度，材质，稳定性，一致性去要求。
而这些，都和具体的2835灯珠实际应用相关。
所以，如果你想了解更多更详细的2835灯珠参数，请咨询2835灯珠生产厂家台宏光电客服工程师。
2835单晶0.5W暖白规格书(50-55LM)
廣東省廣州市荔灣區芳村東沙荷景路9號（東朗工業園）2棟201電話:+86-20-81402798 81414708 傳真:81402027 E-mail:xhm@ SMD LED PRODUCT SPCIFICATION2835 Single chipDESCRIPTIONWhite smd led(0.5W)CUSTOMERDATEREV v1.0PREPARED CHECK APPROVED LumenMaxCustomerRevision NoteDate Revision Page Vision2012/3/18Initiate Document2~11V1.01. FeaturesSamll Size(2.8*3.5*0.8mm)Industry Standard FootprintHigh EfficiencyPb-FreeSoldering methods: IR reflow soldering Chip Dice: InGaN2. DimensionsUnit:mm Tolerance:±0.1mmCathode mark2.003.302.80 2.602.100.60 3.500.252.10 1.900.801 2213. Reconnended Soldering Pattern(Units:mm)4.000.60 2.502.104. Typical Electrical & Optical Characteristics(Ta=25°)Items Symbol Condition Device Min. Typ. Max. Unit Forward voltage VF I F=150mA 2.9 --- 3.5 VReverse Current IR VR=5V --- --- 10 μACoIor Rendering Index Ra 80Color temperature TC I F=150mA 2900 3000 3100 KLuminous Intensity LM I F=150mA 50 53 55 LMView Angle 2θ 1/2 I F=150mA --- 120 ---Notes:1.Luminous Intensity: +/-10%2. Forward Voltage: +/-0.1V.5.Absolute Maxinum Ratings at (Ta=25°)Parameter Rating UnitsPower dissipation 500 mWDC Forward Current 150 mAPeak Forward Current[1] 150 mAReverse Voltage 5 VOperating Temperature -40°C To +85°CStorage Temperature -40°C To +85°CNote:1. 1/10 Duty Cycle, 0.1ms Pulse Width.6. Electro-optical characteristics at(Ta=25℃)ParameterValue UnitMin.Max.Forward voltage07 2.8 3.0 V08 3.0 3.2 09 3.2 3.4 103.43.6Notes:1. Luminous Intensity: +/-10%2. Forward Voltage: +/-0.1V.7. Typical optical characteristics curves8. Chromaticity BinCool white CIEM4M3M2M1YA2YA1E2E1Warm white CIEYF3YG3YG4YG5YG6 YF6 YF5 YF49. Reflow profile■Temperature-profile (Surface of circuit board)1. Reflow soldering should not be done more than two times2. When soldering ,do not put stress on the LEDs during heating10. Packaging Specificatio● Feeding Direction● Dimensions of Reel (Unit: mm) ● Reel3000 PCS● Dimensions of Tape (Unit: mm)11. Packaging specificationsA 8.0mmB 178.0mmC 60.0mm D13.0mm。
led2835绿光贴片灯珠规格书
东莞市荧月电子科技有限公司2835绿光规格书2835GREEN SPECIFICATION产品型号 Model NO.:YLT-led2835GC-520描述:led2835绿光贴片发光二极管是行业内标准的封装产品，此类产品为高可靠性及应用范围非常广泛，此高可靠性的产品非常适用于半户外及户外灯具相关,高可靠性要求的应用场合。
特性:尺寸(mm): 2.8 x 3.5 x 0.8mm 表面贴片发光二极管胶体颜色:透明发光颜色:绿光发光角度:120°版次 REV NO.:V01版文件编号Document NO.:TY-C030002日期 DATE :2015.3.11.外形尺寸D imensions单位(Units):毫米(mm)2.光电特性Electrical / Optical characteristics1/10周期, 0.1 msec脉宽IFP Conditions : 1/10 Duty Cycle, 0.1 msec Pulse Width.½ Rja = Heat resistance from Dice to Ambient temperature (Ta) Rjs = Heat resistance from Dice to Solder temperature of Cathode Side (Ts) (3) 原始光电参数Initial Electrical/Optical Characteristics (TA=25ºC)(4)发光强度范围Luminous Intensity Ranking (TA=25ºC)允许误差± 10%Luminous Intensity Measurement allowance is ± 10%.(5)颜色范围Color Ranking (TA=25ºC)允许误差± 0.01Color Coordinates Measurement allowance is ± 0.01.3.包装PACKAGING(1)LEDS在装带之后纸箱包装. The LEDs are packed in cardboard boxes after taping.(2)装带规格Taping Specifications (单位:毫米Units:mm)(3)卷轴尺寸Reel Dimension装带数量2000个/卷2000Pcs/Reel(3) 最小包装标签注明以下:产品名称.批号.光电范围.数量.The label on the minimum packing unit shows ; Part Number, Lot Number, Ranking, Quantity.(4)请注意防水防潮Keep away from wate r, moisture in order to protect the LEDs.(5) 须采取适当防护措施,以防包装箱跌落或受到强力撞击造成对产品的损伤.The LEDS may be damaged if the boxes are dropped or receive a strong impact against them. so precautions must be taken to prevent any damage.4.可靠性RELIABILITY*) U.S.L.：Upper Standard Level **) L.S.L.：Lower Standard Level 5.注意事项Cautions(1) 焊接条件Soldering Conditions本产品最多只可回焊两次,且在首次回焊后须冷却至室温之后方可进行第二次回焊.Number of reflow process shall be less than 2 times and cooling process to normal temperature is required between first and Second soldering process. 推荐焊接条件(Recommended soldering conditions)有铅回焊（Lead Solder ） 无铅回焊(Lead-Free Solder)推荐焊盘式样(Recommended Soldering Pattern ) 单位:毫米( Units:mm)(2)静电 Static Electricity触摸LED 时,推荐使用防静电手腕带或防静电手套.It is recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs. 所有装置、设备、机器均应接地.All devices, equipment and machinery must be properly grounded.静电损坏的LED 会显示出异常特征:正向电压变低或在低电流时死灯.标准: I F =0.5mA 时, V F > 2.0VDamaged LEDs will show some unusual characteristics such as the forward voltage becomes lower, or the LEDs do not light at the low current. Criteria : (V F > 2.0V at I F =0.5mA) (3)防潮包装Moisture Proof Package使用防潮包装It is recommended that moisture proof package be used .(4)储藏Storage打开包装袋之前,LED在温度为30°C或更低湿度70%RH以下,可保存一年.Before opening the package ,The LEDs should be kept at 30°C or less and 70%RH or less. The LEDs should be used within a year.（5）打开包装之后,应在24hrs 内焊接完毕.After opening the package, The LEDs should be soldered within 24 hours (1days) after opening the package. If unused LEDs remain, they should be stored in moisture proof packages, such as sealed containers with packages of moisture absorbent material (silica gel).下列情况发生时，须要在焊接前重新烘烤60 ± 5°C,24小时以上。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
C62 N13 C63
0.34
C32 C43 C33
0.32
0.3 0.3 0.32 0.34 0.36 0.38 0.4 0.42 0.44 0.46
X
SPEC NO：B-13-A-0740
REV NO: A/3
DATE: MAR/04/2015
PAGE: 7 OF 14
HL-A-2835H431W-S1-08-HR3
Electrical / Optical Characteristics at Ta=25°C
Parameter（参数） Forward Voltage 正向电压 Viewing Angle 角度 Color Rendering Index 显色性指数 Reverse Current 反向电流 Symbol （符号） VF 2θ1/2 Ra IR Min. （最小） 2.8 -80 -Typ. （平均） -120 ---
RoHS
Specification
规 格 书
Customer Name：
客户名称：
Customer P/N：
客户品号：
Factory P/N： HL-A-2835H431W-S1-08-HR3
公司品号：
Sending Date：
送样日期：
Client approval
客户审核
Hongli approval
SPEC NO：B-13-A-0740
REV NO: A/3
DATE: MAR/04/2015
PAGE: 5 OF 14
HL-A-2835H431W-S1-08-HR3
Typical optical characteristics curves 典型光学特性曲线
Relative spectral emission 相对光谱分布特性曲线
ESD
1000
V
Operating Temperature（操作温度）
Topr
-40 ~ +85
℃
Storage Temperature（保存温度） Thermal Resistance （Junction / Soldering point） 热阻 Junction Temperature结温 Note:（备注）
鸿利光电审核
Approval
核准
Audit
确认
Confirmation
制作
Approval
核准 林德顺
Audit
确认
Confirmation
制作 黄雪梅
□ Qualified
接受
□ Disqualified
不接受
DATE: 日期：
Adr：Airport High-tech Industry Base Jingu South Road(XianKe 1st Road Intersection), Huadu District,Guangzhou,China
电性与光学特性
Max. （最大） 3.4 --10 μA Units （单位） V deg Test Conditions 测试条件 IF=60mA IF=60mA IF=60mA VR = 5V
Note:(备注） 21/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value. 21/2 是半值角,指光强是光学中心线光强的1/2处到光学中心线的角度 2. The above luminous flux measurement allowance tolerance is ±10%. 上述发光通量的测试允许公差为±10% 3. The above Color Rendering Index measurement allowance tolerance is ±2 以上显色性指数的测试允许公差为±2 4. The above forward voltage measurement allowance tolerance is ±0.1V. 以上所示电压测量误差±0.1V 5. The above color coordinates measurement allowance tolerance is ±0.003. 以上所示坐标测量误差±0.003
Mass Production list （批量生产目录）
Part No. 型号 CCT（K） Min 5700 4750 HL-A-2835H431WS1-08-HR3 3800 2800 4000 3000 4250 3100 26 25 28 27 IF=60mA IF=60mA CCT（K） Typ 6000 5000 CCT（K） Max 6500 5300 Φ（lm） Min 26 26 Φ（lm） Typ 28 28 Test Conditions 测试条件 IF=60mA IF=60mA
Bin Range of Chromaticity Coordinate Bin区分类及色坐标范围
CCT 色温 Bin Code Bin代码 CIE_x 0.3205 0.3117 C32 6000-6500K 0.3131 0.3213 6000K 0.3213 0.3131 C33 6000-6500K 0.3150 0.3226 0.3376 0.3461 C62 5000-5300K 0.3451 0.3372 5000K 0.3372 0.3451 C63 5000-5300K 0.3441 0.3368 0.3731 0.3839 N42 4000-4250K 0.3803 0.3703 4000K 0.3703 0.3803 N43 4000-4250K 0.3767 0.3675 0.3634 0.3578 0.3716 0.3777 N53 3800-4000K 0.3858 0.3767 0.3690 0.3634 0.3803 0.3903 0.3777 0.3839 0.3777 0.3716 0.3437 0.3378 0.3853 0.3920 N52 3800-4000K 0.3903 0.3803 0.3839 0.3777 0.3497 0.3561 N13 4750-5000K 0.3514 0.3441 0.3839 0.3947 0.3496 0.3437 0.3920 0.3987 0.3451 0.3530 0.3561 0.3625 0.3561 0.3497 0.3190 0.3262 0.3616 0.3685 N12 4750-5000K 0.3530 0.3451 0.3625 0.3561 0.3371 0.329 C43 5700-6000K 0.3298 0.3227 0.3461 0.3545 0.3315 0.3251 0.3685 0.3754 0.3219 0.3296 0.3360 0.3429 0.329 0.3371 CIE_y 0.3481 0.3393 C42 5700-6000K 0.3296 0.3219 0.3429 0.3360 Bin Code Bin代码 CIE_x 0.3211 0.3294 CIE_y 0.3468 0.3542
Cool White 1.0
Warm White
Neural White
Relative luminous intensity
0.8
0.6
0.4
0.2
0.0 380 460 540 620 Wavelength(nm) 700 780
Radiation diagram
辐射图特性曲线
SPEC NO：B-13-A-0740
SPEC NO：B-13-A-0740
REV NO: A/3
DATE: MAR/04/2015
PAGE: 2 OF 14
HL-A-2835H431W-S1-08-HR3
Selection Guide（选择指南）
Part No. 型号 HL-A-2835H431W-S1-08-HR3 Chip Materials 芯片材料 InGaN Lens Type 胶体类型 Yellow Diffused
Tstg
-40 ~ +100
℃
Rthj-s
35
℃/W
Tj
115
℃
1. 1/10 Duty cycle, 0.1ms pulse width.（脉宽0.1ms,周期1/10）
SPEC NO：B-13-A-0740
REV NO: A/3
DATE: MAR/04/2015
PAGE: 4 OF 14
HL-A-2835H431W-S1-08-HR3
Junction Temperture＜115℃
100
Relative Luminous Intensity
2.0
Forward Current(mA)
80
1.5
60
1.0
40
20
0.5
0 0 20 40 60 Soldering Temperature 80 100 Ts(℃)
0.0 0 10 20 30 40 50 60 70 80 90 Forward Current(mA)
Description（描述）
The White LED which was fabricated using a blue chip and the phosphor 白光LED由蓝光芯片与荧光粉激发而成
ATTENTION
OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES 注意：操作时应注意静电敏感 释放设备装置
SPEC NO：B-13-A-0740
REV NO: A/3