汽车座椅安全性检查专题培训课件

2019/12/11
OK17
Safety Check—S32
S32:Sections through all Interior Protrusion requirement 所有内部突出物要求的截面
GB15083-2006: Area 3 R≥3.2
2019/12/11
GB15083-2006 / ECE R17—高度750mm以下无使用位置，头枕高度不应低于 800mm
2019/12/11
头枕处于最低位置 Headrest in lowest position
头枕处于最高位置 Headrest in highest position
OK 3
Safety Check—S3
2019/12/11
11
Safety Check—S17
S17:Clearance of seat back to B pillar for SIAB deployment 用于侧向安全气囊展开的座椅靠背到车身B柱距离
Guideline: >=60mm
2019/12/11
NOK for qoros 12
Safety Check—S29
S29:Pelvic impact Zone 臀部侧撞保护区域
Guideline: No Sharp edge
2019/12/11
13
Safety Check—S30
S30:Clearance for Eurosid II backplate for reduction of side impact forces on dummy ribs Eurosid II 模型靠背与靠背骨架夹角，减少侧撞对肋骨的伤害
Low Most Position
Middle Position
2019/12/11
Whiplash score issue, CF11 17mm
NOK 6
Safety Check—S8
S8:Requirement of head restraint gaps and clearance to seat back (upper most and lowest position) 头枕间隙以及头枕到座椅靠背间隙检查（头枕最高和最低位置）
GB14167:α值应为30°~ 80°(非带扣侧)
2019/12/11
9
Safety Check—S10
S10:Safety belt anchorage zone (whole travel window) 安全带系统安装区域（所有行程范围）o
GB14167:α值应为45°~ 80°(带扣侧)
2019/12/11
10
Safety Check—S16
S16:SIAB location 侧向安全气囊位置
Guide line: 1. SAB与座椅表面的尺寸满足右边图示尺寸，设计座椅撕裂线时
，气囊距撕裂线距离应为20～40mm。 2. SAB与座椅STO面的距离应为10～15mm
Carry over CF11 Back Frame and Airbag
S9:Section through headrest showing the impact angle of 45 degrees from rear side 头枕截面显示从后部向头枕的45度角碰撞
2019/12/11
OK 8
Safety Check—S10
S10:Safety belt anchorage zone (whole travel window) 安全带系统安装区域（所有行程范围）o
2019/12/11
OK 4
Safety Check—S6
S6:Distance from headrest top surface to headrest frame 从头枕上表面到头枕骨架的距离
fmvss 202a <25mm
2019/12/11
NA 5
Safety Check—S5,S7
S7:IIHS requirement on headrest by using HRMD 用头型测量设备（HRMD）对IIHS要求的校核
汽车座椅安全性检 查
Safety Check
2019/12/11
2
Safety Check—S1,S2
S1 S2:Distance from H point to headrest top surface at headrest full down/up position along torso angle 沿着靠背躯干线，从H点到头枕最低(最高)位置的上表面的距离.
S3:Section through headrest perpendicular to torso line and 65mm downward from headrest top surface 垂直靠背躯干线，从头枕上表面65mm向下的头枕截面
GB15083-2006 / ECE R17— ≥170mm for the width of head restraint
GB15083-2006: Area 1 R≥2.5
2019/12/11
OK16
Safety Check—S32
S32:Sections through all Interior Protrusion requirement 所有内部突出物要求的截面
GB15083-2006: Area 2 R≥5.0
NA
2019/12/11
14
Safety Check—S31
1:Anti-Submarining Guideline 防下潜区域检查（cushion）
2019/12/11
NO15
Safety Check—S32
S32:Sections through all Interior Protrusion requirement 所有内部突出物要求的截面
GB15083-2006 FMVSS 202a:头枕最低位置与靠背间隙不大 于25mm或165直径的球相切点间距不大于60mm
Headrest Carry over from CF14K
STO change to less than 15mm(CF11 14mm)
2019/12/11
7
Safety Check—S9