英国CITY废气传感器 NX1气体检测仪
氧电池
英国CITY 氧气传感器点击察看大图产品名称： 英国CITY 氧气传感器产品型号： 2FO 5FO 40X产品展商： 北京乐氏联创科技有限公司产品产地： 英国 产品价格： 面议联系该产品厂商产品详细说明氧气传感器 概况所有的氧气传感器都是自身供电，有限扩散，其金属-空气型电池由空气阴极，阳极和电解液组成。
氧气传感器简单来说是一个密封容器（金属的或塑料的容器），它里面包含有两个电极：阴极是涂有活性催化剂的一片PTFE （聚四氟乙烯），阳极是一个铅块。
这个密封容器只在顶部有一个毛细微孔，允许氧气通过进入工作电极。
两个电极通过集电器被连接到传感器表面突出的两个引脚，而传感器通过这两个触角被连接到所应用的设备上。
传感器内充满电解质溶液，使不同种离子得以在电极之间交换（参见图1）。
Figure 1 - Schematic of oxygen sensor.进入传感器的氧气的流速取决于传感器顶部的毛细微孔的大小。
当氧气到达工作电极时，它立刻被还原释放出氢氧根离子：O2 + 2H2O + 4e- " type="#_x0000_t75">4OH-这些氢氧根离子通过电解质到达阳极（铅），与铅发生氧化反应，生成对应的金属氧化物。
2Pb + 4OH- " type="#_x0000_t75">2PbO + 2H2O + 4e-上述两个反应发生生成电流，电流大小相应地取决于氧气反应速度（法拉第定律），可外接一只已知电阻来测量产生的电势差，这样就可以准确测量出氧气的浓度。
电化学反应中，铅极参与到氧化反应中，使得这些传感器具有一定的使用期限，一旦所有可利用的铅完全被氧化，传感器将停止运作。
通常氧气传感器的使用寿命为1-2 年，但也可以通过增加阳极铅的含量或限制接触阳极的氧气量来延长传感器的使用寿命。
毛细微孔氧传感器和分压氧传感器城市技术生产的氧气传感器根据进入传感器的氧气的扩散方式的不同分为两种，一种是在传感器顶部设有一毛细微孔，而另一种设有一层固体薄膜允许气体通过。
英思科CZ型多种气体测定器说明书
气体检测专家使用说明书英思科宗旨保护地球各个角落人类的生命随时随地提供最高品质的产品和最优质的服务尊敬的用户：感谢您购买并使用英思科的产品——CZ型多种气体测定器。
您所购买的CZ型多种气体测定器每天都能为您提供可靠的气体检测服务。
该产品是我们最严格的规范下设计、制造、测量和认证的。
参照本说明书的介绍，您只需做最少量的维护工作，就能享受本仪器长年为您提供的最可信赖的气体检测服务。
我最为关心的是：在未来的几个月，甚至几年内，您是否对您所购买的CZ型多种气体测定器的性能感到满意。
衷心希望：如果您有任何疑问或意见，请来电与我们联系。
通常一通电话咨询就可帮助您用较少的时间解决问题。
请别犹豫，立即与我们联系：400-820-2515。
英思科的全体员工为能有机会向您提供服务而深表荣幸。
您最诚挚的，Kent D . McElhattan总裁兼首席执行官美国英思科公司目录1、警告及注意事项2、仪器拆箱3、认证4、仪器示图5、简介6、仪器操作气体读数模式操作模式调零/标定模式峰值显示模式 TWA读数观察模式STEL读数观察模式7、设置模式低浓度气体报警设定值高浓度气体报警设定值TWA报警设定值STEL报警设定值时钟设置日历设置安全密码设置调零/标定保护设置8、仪器调零/标定9、数据记录10、CH4超量程11、保养和维修清洗电池充电12、SP40采样泵13、技术指标14、可替换零件清单15、质量保证16、版权17、使用小贴士煤矿矿用产品安全标志证书3 4 4 5 6 6 6 7 8 8 8 9 9 9 10 10 11 12 12 13 13 14 15 15 15 15 15 16 16 17 18 19 20警告及注意事项不正确的操作或不适宜的使用环境，可能会消弱仪器的性能。
为了最安全最有效的使用仪器，请仔细阅读下列正确操作程序和使用环境。
请在使用前认真阅读使用说明书。
在氧气不足的大气环境中可能造成可燃气体读数低于实际浓度。
英国CITY原装进口5FO氧气传感器 电化学氧气检测仪 烟道专用高精度氧气检测模块
5FO CiTiceL ®Performance CharacteristicsNominal Range Max Overload Expected Operating Life Output Signal T 95 Response Time Temperature Range Temperature Coefficient Pressure Range Pressure Coefficient Operating Humidity Long Term Output Drift Maximum Load Resistor Storage Life Recommended Storage Temperature0-25% Oxygen 30% OxygenTwo years in Air0.41 ± 0.05mA in Air <20 seconds -20°C to +45°C 0.2% signal/°CAtmospheric ± 10%<0.02% signal/mBar 0 to 99% RH non-condensing <5% signal loss/year 100ΩSix months in CTL container0-20°C44 gNoneSix months in CTL container0-20°C 12 months from date ofdespatchPhysical CharacteristicsWeight Position Sensitivity Storage Life Recommended Storage TemperatureWarranty Period N.B.All performance data is based on conditions at 20°C,50%RH, and 1013mBar深圳市深国安电子科技有限公司地址：广东省深圳市龙华新区牛栏前大厦Ａ１５０９网址：ｗｗｗ．ｓｉｎｇｏａｎ．ｃｏｍ ｗｗｗ．ｓｉｎｇｏａｎ．ｃｏｍ．ｃｎ ｗｗｗ．ｓｈｅｎｇｕｏａｎ．ｃｏｍ蒋小姐：１３４ ２８７６ ２６３１ 电话：８６ ７５５－８５２５８９００Every effort has been made to ensure the accuracy of this document at the time of printing. In accordance with the company’s policy of continued product improvementCity Technology Limited reserves the right to make product changes without notice. No liability is accepted for any consequential losses, injury or damage resulting from the use of this document or from any omissions or errors herein. The data is given for guidance only. It does not constitute a specification or an offer for sale. The products are always subject to a programme of improvement and testing which may result in some changes in the characteristics quoted. As the products may be used by the client in circumstances beyond the knowledge and control of City Technology Limited, we cannot give any warranty as to the relevance of these particulars to an application. It is the clients’ responsibility to carry out the necessary tests to determine the usefulness of the products and to ensure their safety of operation in a particular application.Performance characteristics on this data sheet outline the performance of newly supplied sensors. Output signal can drift below the lower limit over time.LinearityThe output signal of an Oxygen CiTiceL follows the relationship:S = K log e 1/(1-C)where:S = Output signal;C = Fractional oxygen concentration;K = a constant for the sensor.For most applications the deviation from a linear response will be insignificant, and no compensation needed. For example, the graph below shows the output of a sensor calibrated in air (20.9% O 2). In this case the maximum error in the 0-25% range is ≈0.5% at around 10% O 2.5FO CiTiceLTypical Temperature Coefficient Data-101020304050Temperature (°C)O u t p u t (% o f 20°C S i g n a l )深圳市深国安电子科技有限公司地址：广东省深圳市龙华新区牛栏前大厦Ａ１５０９网址：ｗｗｗ．ｓｉｎｇｏａｎ．ｃｏｍ ｗｗｗ．ｓｉｎｇｏａｎ．ｃｏｍ．ｃｎ ｗｗｗ．ｓｈｅｎｇｕｏａｎ．ｃｏｍ蒋小姐：１３４ ２８７６ ２６３１ 电话：８６ ７５５－８５２５８９００。
英国CITY气体传感器3NFF过滤型一氧化氮传感器3系尺寸,抗硫化物干扰
®Tel:+44 23 9232 5511, .ax:+44 23 9238 6611, sensors@, Doc. Ref.:3N...p65Performance CharacteristicsNominal Range Maximum Overload Inboard .ilter Expected Operating Life Output Signal Resolution Operating Temperature Range *see Note1Pressure Range Pressure Coefficient T 90 Response Time Relative Humidity Range Typical Baseline Range (pure air)Maximum Zero Shift (+20°C to +40°C)Long Term Output Drift Recommended Load ResistorBias Voltage Repeatability Output Linearity 0-1000ppm 5000ppmTo remove effect of SO 2 influe streamThree years in air0.10 ± 0.02 µA/ppm1ppm-20°C to +40°CAtmospheric ± 10%0.01% signal/mBar ≤25 seconds15 to 90% non-condensing 0 to +12ppm equivalent30ppm equivalent <2% signal loss/month10 Ω+300mV 2% of signal LinearPhysical CharacteristicsWeightPosition SensitivityStorage LifeRecommended StorageTemperatureWarranty Period22g NoneSix months in CTL container 0-20°C12 months from date of despatchNote1:While not being used to measure NO the 3N./. canwithstand temperatures of up to +50°CN.B.All performance data is based on conditions at 20°C,50%RH, and 1013mBar深圳市深国安电子科技有限公司Ｓｈｅｎｚｈｅｎ Ｓｉｎｇｏａｎ Ｅｌｅｃｔｒｏｎｉｃ Ｔｅｃｈｎｏｌｏｇｙ Ｃｏ．，ＬｔｄＣＩＴＹ传感器代理及气体检测仪商ｗｗｗ．ｓｉｎｇｏａｎ．ｃｏｍEvery effort has been made to ensure the accuracy of this document at the time of printing. In accordance with the company s policy of continued product improvement City Technology Limited reserves the right to make product changes without notice. No liability is accepted for any consequential losses, injury or damage resulting from the use of this document or from any omissions or errors herein. The data is given for guidance only. It does not constitute a specification or an offer for sale. The products are always subject to a programme of improvement and testing which may result in some changes in the characteristics quoted. As the products may be used by the client in circumstances beyond the knowledge and control of City Technology Limited, we cannot give any warranty as to the relevance of these particulars to an application. It is the clients responsibility to carry out the necessary tests to determine the usefulness of the products and to ensure their safety of operation in a particular application.Performance characteristics on this data sheet outline the performance of newly supplied sensors. Output signal can drift below the lower limit over time.The 3N./. Nitric Oxide CiTiceL is available with side tags, gold-plated PCB pins, or both PCB pins and side tags. To ensure the appropriate option is supplied care must be taken to provide the correct code when ordering.Ordering InformationCross-sensitivity DataCiTiceLs may exhibit a response to certain gases in a sample other than the target gas. The table below shows the typical response of 3N./. sensors to a number of common cross-interfering gases. The figures are expressed as a percentage of the primary sensitivity (i.e. nitric oxide = 100%).。
Honeywell Analytics 毒气 可燃气体 氧气探测器 MDA Scientific 操
HoneywellAnalytics©2004 Honeywell Analytics Issue 1 12/2004 MIDAS-A-001目录1 目录 22 概述 53 产品概述 5 3.1 主机架 6 3.1.1 显示器模块 63.1.2 泵模块 7 3.1.3 传感器暗盒腔 73.2 安装托架底座 73.2.1 安装托架 73.2.2 终端模块 73.3 传感器盒 83.3.1 偏致传感器盒 83.4 机壳 84 默认配置 95 安装95.1 探测器的安装和定位 105.2 机械安装 115.3 样品和排气管道计算 125.4 在线过滤器 135.5 本地化探测器选购件 145.6 电气安装 155.7 电连接 17 5.8 改装主机架 185.9 安装传感器盒 196 探测器启动程序 197 总体操作 21 7.1 正常操作模式 217.1.1 重置报警、故障和维护故障 227.2 浏览模式 227.2.1 浏览模式菜单概述 237.3 设置、校准和测试模式概述 247.3.1 设置菜单概述 247.3.2 校准菜单概述‘CAL’ 267.3.3 测试菜单概述‘ tESt’ 278浏览、设置、校准和测试模式子菜单的导向的详细程序 288.1 浏览模式 288.1.1 复查软件‘SW’ 288.1.2 复查报警‘ ALm’ 298.1.3 复查故障‘ FLt’ 298.1.4 复查校准 ‘ CAL’ 298.1.5 复查日期和时间‘timE’ 298.1.6 复查探测器地址‘ nEt’ 308.1.7 复查事件标识‘ Hi St’ 308.2 设置、校准和测试模式 308.2.1 设置菜单‘ SEt’ 318.2.2 设置报警‘ ALm’ 318.2.3 设置故障‘ FLt’ 348.2.4 设置校准间距 ‘ CAL’ 348.2.5 设置日期和时间 ‘timE’ 558.2.6 设置地址‘ nEt’ 358.2.7 设置密码 ‘ PWd’ 368.3 校准菜单‘CAL’ 368.3.1 零点校准 ‘ 0CAL’ 368.3.2 间距校准‘ SPAn’ 378.3.3 流量校准‘ FLoW’ 388.3.4 mA 校准 ‘mA 4-20’ 388.4 测试菜单‘ tESt’ 398.4.1 颠簸测试 ‘ bUmP’ 398.4.2 报警/故障测试‘ Si m’ 398.4.3 禁止状态‘ I nH’ 409 常规维护 41 9.1 传感器盒的更换 419.1.1 传感器盒的安装/更换 419.2 泵的更换 43 9.3 重新组装探测器 469.4 过滤器的更换 4610 热解器模块选项 4710.1 安装热解器模块 4810.2 重新组装MIDAS® 探测器 4911 模拟输出模块 51 11.1 安装模拟模块 5111.2 重新组装MIDAS® 探测器 5212 找出故障并诊断 5313 REFLEX®ٛ5414 内置的网络服务器 5414.1 物理的网络组件 5414.2 网络设置 5414.3 运行网络浏览器 5415 典型安装拓扑 5615.1 常规安装 57 15.2 Modbus/TCP 安装 5715.3 通过以太网供电(POE) 的安装 5716 订购信息 58 16.1 MIDAS® 发送器 5816.2 MIDAS®热解器 5816.2 MIDAS® 热解器 5816.3 MIDAS® 模拟输出模块5816.4 MIDAS®插入式传感器盒（标准保修期） 5916.5 MIDAS®插入式传感器盒（延长保修期）6016.6 完整的MIDAS®气体探测器套件 6116.7 附件及备件 6117 一般规格 6218 校准及颠簸测试 6319 保证声明6720 软件菜单叙述图表 6920.1 高级6920.2 浏览模式7020.3 复查软件的信息、报警、故障及气体校准7120.4 复查日期/时间和网络7220.5 复查事件日志7320.6 设置模式7420.7 设置报警、故障及气体校准 7520.8 设置日期/时间和网络7620.9 设置密码7720.10 校准模式7820.11 校准气体零点及间距7920.12 校准——流量校准 8020.13 校准——4-20 mA 8120.14 测试模式8220.15 测试颠簸、报警/故障模拟 8320.16 测试禁止8421 联系详情 852 概述作为一个提取式气体取样系统，MIDAS气体探测器能在本地或从一个远程点提取一个样品到位于探测器机架内的传感器盒。
英国GMI_PS200四合一气体检测仪
0-25%
0.1%
电化学
CO
0-1000ppm
1ppm
电化学
H2S
0-500ppm
1ppm
电化学
青岛聚创环保设备有限公司
外壳:
橡胶外壳
下Hale Waihona Puke 测试:3m防护等级:
IP67
反应时间:
LEL=10秒O2=10秒CO=25秒H2S=35秒
证书:
IEC Ex ia d IIC T4 Gb ATEX Ex II 2 G Ex ia d IIC T4
保修:
1年
传感器型号
气体
量程
误差
传感器类型
LEL
0-100%LEL
1%LEL
催化燃烧
英国GMI PS200四合一气体检测仪
一、简介
GMI PS200可同时检测仪可燃气体、O2、CO和H2S，并可按客户需要对一种或任意组合多种气体检测。检测仪结果同时显示在屏幕上。用户可随时启动手动操作。标准的USB借口可用于充电和数据传输，电子版用户手册方便客户存放。PS200系统采用标准的数据记录模式，内部记忆功能可存储180次
测试记录。
二、参数
技术参数
尺寸:
121*59*32mm
重量:
230g(80z)含泵
215g(7.60z)不含泵
适用温度:
-20℃-+50℃(-4℃F-122°F)
湿度:
0-95% R.H非凝结性
声报:
LED灯闪烁>90分贝
显示:
绿/红灯显示
数据标准:
坏境标准
电池:
锂电池
连续使用14个小时
充电时间4个小时
Zoomlion XNX Universal Transmitter 气体检测设备说明书
A universal transmitter for toxic, oxygen and combustible gas detection compatible with allHoneywell gas sensing technologiesXNX ™Universal TransmitterThe XNX Universal Transmitter, now with HART EDDL, marks a new turn in gas detection from Honeywell Analytics. It supports the widest range of sensors on a common platform and offers a modular choice of inputs and outputs.Bringing together the best solutions in gas detection High performance• Flammable gas detection 0 to 100% LFL/LEL • P oint IR with heated optics provides immunity to poisoning and no hidden faults • O pen-path IR flammable gas detection in LEL-m measurement• Electrochemical cell offers toxic gas detection in ppm • I R cell provides CO 2 and combustible gas monitoring • R obust and reliable operation in explosive areas and harsh environmentsFlexible Operation• 3 versions - supports (Catalytic Bead and IR Cell), Electrochemical Cell and IR (point and open-path) gas detection • M ulti-Purpose Detector (MPD) with field serviceable mV,Catalytic bead and IR Cell capability• 4-20mA with HART ® as standard• H ART Enhanced Device Description Language(EDDL) software*• M ultiple communications options include up to 3 relays, MODBUS ® and FOUNDATION ® H1 Fieldbus• O ptional local IS port for handheld HART configuratorEasy to Use • L arge, backlit, easy-to-view LCD display offers multi-sensory indicators (visual icons, colored buttons, text, etc.) to display gas and sensor readings • U ser interface supported by 8 selectable languages (English, Spanish, German, Italian, Portuguese, French, Russian, Chinese)• Self-test and fault indication features • N on-intrusive, one-man operation • Q uick calibration with auto-inhibitEasy to Install• 3 or 4 wire operation, source, sink or isolated • Simple plug-in sensors and replaceable cells • N EMA 4X IP66 rated for rugged indoor/outdoor use • F ive conduit entries for ease of installationCost Effective• Minimal training required • One-man operation• Plug-in sensor replacement • A ll necessary accessories includedXNX is designed for flexible integration, simple installation, user-friendly operation and straight-forward maintenance. It is ideal for use with a range of gasmonitoring controllers or industry standard PLCs. The introduction of our HART Enhanced Device Descriptor Language (EDDL) software provides users with an at-a-glance indication of the health of their gas detectors in the field.Electrochemical • P roven electrochemical sensing technology • S urecell™ electrochemical cells are ideal for hot and humid environments • L ong life sensing cells (typical >2 years)• P atented ‘Reflex’ sensing elementverification diagnostics• S ensor recognition software autoconfigures transmitter• P lug and play factoryconfigured sensors• I ntrinsically safe sensor connectionpermits hot swap, reducing down timeCatalytic Bead • S upports Honeywell Analytics 705, 705HT, Sensepoint, Sensepoint HT and MPD sensors • F ast response to wide range of hydrocarbons and flammablesInfrared (Open Path IR, Point IR, IR Cell)• S upports Honeywell Analytics Searchline Excel, Searchpoint Optima Plus • Failsafe operation • Fast speed of response • Reduced routine maintenance • Immune to catalytic poisons • Long operating life • Works in inert atmospheresThe XNX’s powerful advancedcommunications module – including our new HART EDDL software – adds increased efficiency, functionality and flexibility to a gas detection network.XNX offers a variety of communication options to suit your industrial operation’s unique and changing needs. HART communication comes standard on the XNX — with optional EDDL — along with optional Modbus, Foundation Fieldbus or relays. It can interface with a PLC and a host of other protocol compatible devices found in industrial applications. Unique to the XNX and Honeywell Analytics is our new HART EDDL software, which allows you to manage all of your HART devices’ advanced diagnostic data right from your PLC.With the XNX, you are freed from the need to add extra controllers, junction boxes, relays, monitors and other equipment accessories. The integration of our EDDL software also enables the XNX to work with a number of third-party distributed control systems (DCS).Searchline ExcelFoundation Fieldbus705/705HTadvanced diagnostic data at any time.of your HART device.DS01071_v4 8/11© 2011 Honeywell AnalyticsFind out more Contact Honeywell Analytics:AmericasHoneywell Analytics, Inc.405 Barclay Blvd.Lincolnshire, IL 60069USATel: 847.955.8200Toll-free: 800.538.0363Fax: 847.955.8210***********************Technical Services************************Europe, Middle East, Africa Life Safety Distribution AG Weiherallee 11a CH-8610 Uster SwitzerlandTel: +41 (0)44.943.4300Fax: +41 (0)44.943.4398**************************Asia PacificHoneywell Analytics, Asia Pacific #508, Kolon Science Valley (1)187-10 Guro-Dong, Guro-Gu Seoul, 152-050KoreaTel: +82 (0)2.2025.0307Fax: +82 (0)2.2025.0329**************************Please Note:While every effort has been made to ensure accuracy in this publication, no responsibility can be accepted for errors or omissions.Data may change, as well as legislation, and you are strongly advised to obtain copies of the most recently issued regulations, standards, and guidelines. This publication is not intended to form the basis of a contract.Honeywell Analytics Lines of BusinessCommercialGas detection from standalone units to fully engineered, multi-point systems, all offering cost-effective regulatory compliance» Applications: parking structures, chillers, mechanical rooms, office towers, commercial buildings,shopping centers, swimming pools, golf courses, schools and universities, laboratoriesIndustrialRenowned Sieger and Manning gas detection systems with advancedelectrochemical, infrared and open path sensing technologies» Applications: oil and gas, cold storage, water/wastewater treatment,chemicals, engine rooms, plastics and fibers, agriculture, printing and light industrialHigh Tech/GovernmentA complete portfolio of gas and chemical detection instrumentation includinginfrared spectroscopy (MST) with no cross interference, to Chemcassette paper-based solutions (MDA Scientific) offering detection down to parts per billion » Applications: semiconductormanufacturing and nanotechnology, aerospace propulsion and safety, s pecialty chemicals industry, research laboratories, emergency responsePortablesSingle or multi-gas Lumidor and other premium detectors with compact, lightweight designs ranging from simple alarm only units to advanced, fully configurable and serviceable instruments» Applications: underground utility and electricity ducts, boiler rooms, post-fire sites, sewers, industrial plants, industrial hygiene, first responder teams, remote fleetsTechnical Services24/7 global network includes post-sales service and Systems Integration teams» Emergency call out, servicecontracts, on/off-site repair, training and commissioning» Complete range of spares, consumables and accessories。
氧氣盾式感測器 NJ40-FP-SN-P1 商品说明书
12Releasedate:217-1-2415:36Dateofissue:217-1-2416696_eng.xml 1L+L-23R e l e a s e d a t e : 2017-01-24 15:36D a t e o f i s s u e : 2017-01-24106696_e n g .x m lInstructionManual electrical apparatus for hazardous areas Device category 2Gfor use in hazardous areas with gas, vapour and mist EC-T ype Examination CertificateCE marking ATEX marking ¬ II 2G Ex ia IIC T6…T1 GbThe Ex-related marking can also be printed on the enclosed label.Standards EN 60079-0:2012+A11:2013 EN 60079-11:2012 Ignition protection "Intrinsic safety"Use is restricted to the following stated conditions Appropriate typeNJ 40-FP-SN...Effective internal inductivity C i≤ 370 nF ; a cable length of 10 m is considered.Effective internal inductance L i ≤ 300 µH ; a cable length of 10 m is considered.G eneralThe apparatus has to be operated according to the appropriate data in the data sheet and in this instruction manual. The EU-type examination certificate has to beobserved. The special conditions must be adhered to! The ATEX directive and there-fore the EU-type-examination certificates generally apply only to the use of electrical apparatus under atmospheric conditions.The device has been checked for suitability for use at ambient temperatures of > 60 °C by the named certification authority. The surface temperature of the device remains within the required limits.For the use of apparatus outside of atmospheric conditions, a reduction of the per-missible minimum ignition energies may need to be considered.Maximum permissible ambient temperature T amb Details of the correlation between the type of circuit connected, the maximum per-missible ambient temperature, the temperature class, and the effective internal reac-tance values can be found on the EC-type examination certificate.Installation, commissioningLaws and/or regulations and standards governing the use or intended usage goal must be observed. The intrinsic safety is only assured in connection with an appro-priate related apparatus and according to the proof of intrinsic safety. If the Ex-related marking is printed only on the supplied label, then this must be attached in the imme-diate vicinity of the sensor. The sticking surface for the label must be clean and free from grease. The attached label must be legible and indelible, including in the event of possible chemical corrosion. After opening the housing, you should check that the seal is in the correct position and is clean and intact before closing the housing again.Maintenance No changes can be made to apparatus, which are operated in hazardous areas.Repairs to these apparatus are not possible.Special conditionsProtection from mechanical dangerWhen using the device in a temperature range of -60 °C to -20 °C, protect the sensor against the effects of impact by installing an additional enclosure. The information regarding the minimum ambient temperature for the sensor as provided in the datasheet must also be observed.Electrostatic chargeWhen used in group IIC non-permissible electrostatic charges should be avoided on the plastic housing parts. Avoid electrostatic charges that can cause electrostatic dis-charge when installing or operating the device. Information on electrostatic hazards can be found in the technical specification IEC/TS 60079-32-1.Degree of protection required when installing connecting componentsThe connecting parts of the sensor must be set up in such a way that degree of pro-tection IP20, in accordance with lEC 60529, is achieved as a minimum.4Releasedate:217-1-2415:36Dateofissue:217-1-2416696_eng.xml Instruction Manual electrical apparatus for hazardous areasDevice category 1D for use in hazardous areas with combustible dustEC-T ype Examination CertificateCE markingATEX marking ¬ II 1D Ex ia IIIC T135°C DaThe Ex-related marking can also be printed on the enclosed label.Standards EN 60079-0:2012+A11:2013 EN 60079-11:2012Ignition protection "Intrinsic safety" Use is restricted to the following stated condi-tionsAppropriate type NJ 40-FP-SN...Effective internal inductivity C i≤ 370 nF ; a cable length of 10 m is considered.Effective internal inductance L i≤ 300 µHA cable length of 10 m is considered.G eneral The apparatus has to be operated according to the appropriate data in the data sheetand in this instruction manual. The EU-type examination certificate has to beobserved. The ATEX directive and therefore the EU-type-examination certificatesgenerally apply only to the use of electrical apparatus under atmospheric conditions.The device has been checked for suitability for use at ambient temperatures of >60 °C by the named certification authority. The surface temperature of the deviceremains within the required limits.For the use of apparatus outside of atmospheric conditions, a reduction of the per-missible minimum ignition energies may need to be considered.Permissible ambient temperature range Details of the correlation between the type of circuit connected, the maximum per-missible ambient temperature, the surface temperature, and the effective internalreactance values can be found on the EC-type-examination certificate. The maxi-mum permissible ambient temperature of the data sheet must be noted, inaddition, the lower of the two values must be maintained.Installation, commissioning Laws and/or regulations and standards governing the use or intended usage goalmust be observed. The intrinsic safety is only assured in connection with an appro-priate related apparatus and according to the proof of intrinsic safety. If the Ex-relatedmarking is printed only on the supplied label, then this must be attached in the imme-diate vicinity of the sensor. The sticking surface for the label must be clean and freefrom grease. The attached label must be legible and indelible, including in the eventof possible chemical corrosion. After opening the housing, you should check that theseal is in the correct position and is clean and intact before closing the housingagain.Maintenance No changes can be made to apparatus, which are operated in hazardous areas.Repairs to these apparatus are not possible.Special conditionsProtection from mechanical danger When using the device in a temperature range of -60 °C to -20 °C, protect the sensoragainst the effects of impact by installing an additional enclosure. The informationregarding the minimum ambient temperature for the sensor as provided in thedatasheet must also be observed.Electrostatic charge Avoid electrostatic charges that can cause electrostatic discharge when installing oroperating the device. Information on electrostatic hazards can be found in the techni-cal specification IEC/TS60079-32-1. Do not attach the nameplate provided in areaswhere electrostatic charge can build up.Degree of protection required when installing connecting components The connecting parts of the sensor must be set up in such a way that degree of pro-tection IP20, in accordance with lEC 60529, is achieved as a minimum.。
四合一气体检测仪(泵吸式)GasAlertMAX-XT_Manual中文使用说明书
多气体检测仪使用手册有限保证和责任限制BW Technologies LP (BW) 保证，本产品自交付客户之日起在正常使用和保养情况下两年不会出现材料和工艺缺陷。
本保证仅适用于原客户新购买的、未使用过的产品。
BW的保证责任限于：在保证期由BW自行选择对返回到BW授权服务中心的缺陷产品实行退款、维修或更换。
在任何情况下，BW依据本保证承担的责任均不会超过客户购买产品时所支付的实际价格。
以下情况不属于本保证围：1. 保险丝、一次性电池或使用过程中产品正常磨损和破损所需的定期更换零件；2. 根据BW鉴定，任何因误用、改装、疏忽或由事故或不正常操作、处理或使用而损坏的产品；3. 任何由非授权经销商维修或在产品上安装未经许可的零部件所造成的损坏或缺陷；本保证所列出的责任受以下条件限制：1. 正确保管、安装、校准、使用、维护并遵守产品手册说明和BW的任何其他适用建议；2. 客户及时就任何产品缺陷通知BW，必要时，应迅速对产品进行修复。
除非从 BW收到客户的发货指示，否则不能返回任何产品；3. BW有权要求客户提供购买凭证，如原始发票、销售契约或包装收据，以确定产品是否在保证期。
4. 客户同意本保证是客户唯一的赔偿条款，并代替其他全部保证，无论是明示的或暗示的、包括但不限于对于特殊目的适销性或适合性的任何暗示保证。
不论是由于违反本保证还是依据合同、侵权行为或信赖或任何其他理论，BW对特殊、间接、偶然或附带产生的任何损坏或损失，包括数据丢失，概不负责。
由于某些国家/地区或州不允许限制暗示保证的条款，或不允许排除或限制偶然或附带产生的损坏，因此本保证的限制和排除情况可能并不适用于每位客户。
如果本保证的任何规定被有资格的司法管辖法院认为无效或不可执行，将不会影响任何其他规定的有效性或可执行性。
联系 BW Technologies by HoneywellEmail: infogasmonitors.: .gasmonitors.加拿大: 1-800-663-4164简介操作手册提供了GasAlertMax XT气体检测仪基本操作信息. 更详细的操作说明参考随即附带的GasAlertMax XT技术参考手册. GasAlertMax XT气体检测仪用于检测有毒有害气体. 仪器属于个人安全防护设备.个人有责任对于报警做出正确的响应.GasAlertMax XT安全信息-请先阅读请严格遵循手册说明和技术参考指导对仪器进行操作, 否则不能充分返回仪器的防护作用使用仪器前请阅读以下注意事项.注意•警告: 任何其他部件的替代会导致本质安全性的降低.•注意: 出于安全考虑, 设备必须由具有资质的专业人员进行操作或维修. 在使用和操作之前请详细阅读产品使用技术手册.•请在第一次使用前给仪器充电. BW 建议在每次工作使用仪器完毕后给仪器充电.•在第一次使用之前给仪器进行标定并定期进行标定维护, 周期取决与使用频率和传感器曝露在毒气环境中的情况以及污损情况. 传感器必须每隔180天（6个月）进行一次标定.GasAlertMax XT操作手册•标定必须在没有有害气体安全环境中进行.•可燃气体传感器工厂标定使用 50% LEL甲烷. 如果检测不同的可燃气体，使用不同气体进行标定.•避免将可燃气体传感器与铅化物, 硅以及含有氯元素的碳氢化合物接触. 尽管某些有机气体（比如含铅的汽油以及含有卤素的碳氢化合物）会暂时导致传感器被抑制, 多数情况下, 传感器可通过标定恢复.•BW 要求使用已知浓度气体对可燃气体进行检测, 当传感器暴露在有污染物以及有毒物质比如硫化物, 硅蒸汽, 以及含有卤素的碳氢化合物等环境中后.•BW 要求每天使用前对仪器进行通气测试, 将仪器放置在超过报警设置值的气体浓度中确认仪器的声光报警在超过报警浓度数值后能够正常工作. 如果不能, 请对仪器进行标定.•注意: 高浓度LEL读数指示表明爆炸浓度.•传感器在读数快速上升以后出现不稳定的读数减少, 可能说明气体浓度已经超过了测量的上限值, 这个是很危险的.•仅用于氧气浓度不超过20.9%(V/V) 的具有潜在爆炸性的环境中.•GasAlertMax XT 过度暴露在某一浓度的可燃气体中会影响传感器器件正常工作.如•由于高浓度可燃气体引起的报警.•BW采样泵 (XT-RPUMP-K1) 仅适用于 GasAlertMax XT.•警告:错误地使用锂电池 (MX-BAT01) 可能造成火灾或者化学危害. 请勿拆卸, 加热或丢弃.•警告:不要使用其他锂电池作为 GasAlertMax XT 的电源. 这样可能引起燃烧或者爆炸. 订购或更换 MX-BAT01 锂电池, 联系 BW Technologies by Honeywell.•警告:锂聚合物电池放置在 266°F (130°C) 10 分钟会燃烧和爆炸.•废弃的锂电池. 不可拆卸和丢弃在火中.•儿童勿靠近锂电池.•所有标定气瓶必须使用被动流量阀和必须符合以下压力规格:•抛弃式气瓶 0-3000 psig/70 bar•重复使用式气瓶 0-3000 psig/70 barGasAlertMax XT 外部描述项目描述1 可视报警指示 (LEDs)2 采样泵快速连接器3 采样泵灰尘及水汽过滤器4 按键5 背夹6 充电及IR红外通讯口7 扩散面板锁定螺钉8 扩散面板9 声音报警10 液晶显示屏显示单元按键气瓶连接注意标定必须在没有有害气体的安全区域进行. 请不要在充电或刚刚充电完毕时进行标定.注意标定时所用通气管最长不超过3英尺（1 m）.1. 按住○直至仪器出现OFF 关机倒计时. 继续按住○仪器进入标定暂时的关闭状态.2. 仪器重新开启进入CAL 标定倒计时. 继续按住○直到倒计时结束进入标定状态.3. 当仪器对所有传感器进行调零时, 屏幕上会闪烁图标. 如果有传感器调零失败, 这该传感器不能进行标定. 当自动调零结束, 屏幕上显示APPLY GAS.4. 参考气瓶与仪器的连接（第7页）. 连接上被动流量阀和标准气体.注意标定时, 扩散面板必须安装在仪器上.屏幕上会有图标闪烁. 在检测到有效数量的气体后（30秒）, 仪器会发出蜂鸣声. 当仪器在标定时, 屏幕上会闪烁.LCD 会显示CAL DUE. 接下去, 屏幕显示每一个传感器的标定周期. 最后, LCD 显示（比如）CAL DUE d.注意标定可以再任何时候终止. 若要终止标定, 按○. CAL ABORTED 会显示在屏幕上.注意如果启动了Latched Alarms报警锁存功能, 在报警状态时仪器会持续低和高报警（声音,光和振动）, 直到手动确认报警后消除. 当然此时气体浓度应该在报警设定值之下. 通过按○30秒可以暂时关闭声音报警, 但是LCD屏幕仍然会显示最高浓度数值直到报警条件不再存在. 开启、关闭Latching Alarms 功能需要通过 Fleet Manager II设定.操作菜单如果需要更改仪器的参数和参看部信息需使用红外数据套件, Fleet Manager II 软件. 参看GasAlertMax XT技术参考指南和Fleet Manager II 操作手册l. 对于用户和传感器选项，参考以下信息:仪器设置•开机信息（顶行）: 输入一行文本信息, 开机时在LCD上显示（最大25个字符）.•开机信息（底行）: 输入一行文本信息, 开机时在LCD上显示（最大25个字符）.•自检错误锁定(传感器报警锁定): 如果传感器在开机时候检测失败,同时Lockout on Self-Test自检锁定功能开启, Safety Lock On 会显示在LCD上,同时仪器关机.•安全模式: 该功能开启时, SAFE 会一直显示在屏幕上，除非发生报警.•工作状态指示: 工作状态指示能够周期性的提供声音提示, 表明仪器正在正常工作状态. 如果需要更改声音提示周期(每隔1-120 秒), 在Confidence Interval 选项中输入数值. 在电池电量低的状态下该功能会自动关闭.•报警锁存: 报警锁存功能能够是仪器在发生报警时锁定报警, 连续发出声光和振动报警提示. 按确认件可以取消报警. 可视报警可以按住○保持30秒后关闭, 但LCD会继续显示峰值读数浓度直到报警条件消失.•强制标定: 该功能会检测传感器标定周期是否有效,如果仪器超过设定的标定周期,仪器会强制要求仪器进行标定. 用户可以通过Calibration Interval选项设定标定周期(0-365 天).•IR标定锁定: (必须使用IR设备进行标定) 使用该功能时仪器可以进行自动调零, 但是传感器标定必须通过IR接口设备或是MicroDock II管理台来进行.•强制通气测试: 该功能要求用户使用仪器前必须对传感器进行通气测试, 确保仪器传感器对目标气体有正确的响应. 用户可以在Bump Interval选项中设定通气测试的周期 (0-365 天).•地点设定: 如果开启，可以输入连续数字 (1-999) 设定不同区域地点.•强制采样泵测试: 若该功能开启, 开机测试采样泵工作是否正常.•数据记录周期 (秒): 用户可以根据需要更改数据记录周期(1-120 s).•工作状态提示周期 (秒): 仪器提示周期(1-120 s) .•语言: 用户可以通过Fleet Manager II 软件选择自己需要的显示的语言English, Français (法语), Deutsch (德语), Español (西班牙语), 或Português (葡萄牙语).传感器设置(H2S, CO, LEL, O2)•关闭传感器: 开启和关闭传感器.•标气浓度 (ppm): 设定每个传感器标定时标准气体浓度. 设定的标定气体浓度必须与标准气瓶的浓度一致.•标定周期Calibration Interval: 设定下次标定间隔时间 (0-365).•通气测试周期Bump Interval: 设定通气测试周期 (0-365).•低报警Low Alarm (ppm): 设定每个传感器的低报警值.•高报警High Alarm (ppm): 设定每个传感器的高报警值.•TWA 报警 (ppm): 设定 (TWA) 报警值 (仅对毒气传感器).•STEL 报警 (ppm): 设定 (STEL) 报警值 (仅对毒气传感器).•STEL 周期设定 (分钟): 设定 (STEL) 间隔时间5-15 分钟 (仅对毒气传感器).•TWA 周期设定: TWA 周期设定用于设定计算时间超过4-16小时的气体浓度平均值, 确保工人能够安全离开区域.•修正系数Correction Factor (%): 修正系数用于甲烷以外的碳氢化合物. 修正系数仅用于甲烷标定的传感器.•50% LEL = (%CH4): 以体积百分比的形式显示LEL读数值.•开机自动调零Auto-Zero on Startup: 开启该功能时, 仪器会在开机时对传感器进行自动调零(H2S, CO, LEL, and O2).•LEL 体积显示 CH4: 开启该功能时候, 仪器显示体积百分比浓度%CH4甲烷气体而不再显示%LEL.•5% LEL Over-span: 如果开启该功能, 仪器自动在给定的标准气体浓度之上的5%LEL进行设定以满足或优于CSA标准.•20.8% Base Reading: 开启该功功能, 仪器显示大气中的氧气浓度为20.8%. 关闭该功能时, 仪器显示大气中的氧气浓度为20.9%.•低报警确认Low Alarm Acknowledge: 通过按○该功能能够暂时关闭由于低报警产生的声音报警. 振动和LED报警仍然工作 (毒气和LEL).维护为了确保仪器保持良好的工作状态, 请按以下要求进行操作.•标定, 通气测试和仪器的日常检测.•维护所有维护, 通气测试, 标定和报警时间等数据.•用柔软的湿布擦拭仪器外壳. 不要使用溶剂, 肥皂, 或是磨擦机器表面.•不要将仪器浸没在液体中.充电警告必须在安全和无害的气体环境中充电, 充电温度在 32°F-113°F (0°C-45°C).在每天工作后对仪器进行充电. 请参照以下流程就说明进行充电:1. 关机.2. 将充电器插入AC电源中.3. 将充电器插头接入到IR端口槽中. 参照以下说明.4. 充电需6个小时.5. 为了达到电池的全部性能, 新电池需完全充放电3次.更换传感器和传感器过滤器警告为了避免人为损坏, 只能使用为该仪器设计的传感器.注意仪器可以配置 1, 2,或 3种气体或包含模拟传感器. 需要更黄传感器或传感器过滤器请参照以下信息.1. 关机.2. 将采样泵进气口接口连同螺丝取下.3. 将后盖上的六个螺钉取下.4. 由于采样泵的采样管连接在仪器前后外壳上, 打开后盖时注意将后盖先向上抬起然后向左翻开. 将前后盖并排平放.5. 取下PCB板上的螺钉.6. 将PCB板向上取出并向左翻开. 将PCB板传感器向上地放置在后盖上.7. 将传感器滑出（氧气传感器拔出）.8. 插入新的传感器并更换传感器过滤膜.9. 组装好仪器并重新上好螺丝.10. 重新装上六个螺丝.11. 必须重新安装上采样泵和水汽过滤器.12. 安装采样泵接口和固定螺丝.13. 开机然后重新标定新传感器, 请参看标定.技术规格外形尺寸: 13.1 x 7.0 x 5.2 cm (5.1 x 2.8 x 2.0 in.)重量: 300 g工作温度: -20°C to +50°C (-4°F to +122°F)存放温度: -40°C to +60°C (-40°F to +140°F)工作湿度: 10% -100% 相对湿度 (非凝结)防护等级: IP66/67报警设置: 用户可更改检测围:H2S: 0 - 200 ppm (1 ppm )CO: 0 - 1000 ppm (1 ppm )O2: 0 - 30.0% vol. (0.1% vol.)可燃气体 (LEL): 0 - 100% (1% LEL) 或 0 - 5.0% v/v 甲烷传感器类型:H2S, CO, O2: 插拔式/电化学可燃气: 插拔式/催化燃烧O2 测量原理: 毛细孔浓度控制传感器报警设置:TWA 报警, STEL 报警, 低报警, 高报警, 复合式报警, 超量程 (OL) 报警, 电池电量低报警, 工作状态提示, 自动关机报警, 采样泵报警声音报警: 95 dB（30cm）不同频率蜂鸣声可视报警: 红色发光二极管 (LEDs)显示: 字符数字式液晶显示背景灯:当仪器开启时背景灯即开启; 10秒钟后背景灯关闭. 当仪器报警时背景灯会再次打开直到报警解除.自检: 开机自检及连续检测标定: 自动调零和标定用户定义选项:开机信息, 自检失败锁定, 安全模式, 工作状态提示, 报警锁存, 强制标定, 红外标定锁存, 强制通气测试, 本机数据记录, 强制测试锁定, 数据记录周期, 工作状态提示周期, 语言选择传感器选项:传感器开启/关闭, 设置标定数值, 设置标定周期, 设置通气测试周期, 设置报警点,设置STEL周期, 设置TWA周期, 开机自动调零开启/关闭, 5% 超余量标定, 低报警确认, 氧气测量, 和可燃气体测量电池运行时间: 锂聚合物充电电池. 13 小时 (一般)制造年份:从产品系列号可以判断制造年份. 字母后的第一二个数字即为制造年份.E.g., MA 108-000001 = 2008 年制造认证的电池:北美用于GasAlertMax XT产品的认证电池:锂聚合物电池，执行标准 EN50020, UL913, C22.2 No. 157充电电池 (MX-BAT01) 温度锂聚合物电池电池 -20°C Ta +50°C T4充电器: 充电适配器首次充电时间: 6 小时一般充电时间: 6 小时质保: 1年质保含传感器认证:CSA 及 U.S. 认证标准 CAN/CSA C22.2 No. 157 / C22.2 152 ANS/UL - 913 /ANSI/ISA - S12.13 Part 1CSA Class I, Division 1, Group A, B, C, and DATEX CE 0539 g II 1 G Ga Ex ia IIC T4 KEMA 08 ATEX 0001IECEx Ga Ex ia IIC T4用于 GasAlertMax XT 检测器的减压阀每次标定和通气测试时需使用减压阀可使用以下规格减压阀:• 0.5 l/min 加压阀• 被动减压阀警告标定气瓶使用被动流量阀必须满足最大压力流量要求规格:• 抛弃型气瓶 0-1000 psig/70 bar• 重复使用型气瓶 0-3000 psig/207 bar配件及附件型号描述数量REG-0.5 0.5L/min主动阀 1REG-DF-1 被动阀 1iERP:125741D6171/0[中文]© BW Technologies 2008.版权所有。
NO传感器
模块结构MODULE STRUCTURE
33.5mm
21.5mm
3m1m 31mm
3.mm5 1mm
7NE SIDE VIEW
3.5mm 1mm
4NE SIDE VIEW
7NE TOP VIEW
4NE TOP VIEW
接线示意图WIRING DIAGRAM
连接MAX232芯片转串口 RDE
TIN MAX232 TXD
圣凯安科技
NE SENSOR TECHNOLOGY
气体检测行业领先者
智能型NO传感器
智能型一氧化氮NO气体传感器是专门针对气体 探测器生产企业推出的新型智能传感器, 主要为解 决气体探测种类繁多、各品种传感器互不兼容、生 产标定复杂、核心器件更换限制等问题。
采用我司生产的智能型一氧化氮NO气体传感器 则只需开发一款产品, 即可快速响应客户对不同气 体种类探测的需求, 且生产过程简化, 无需重新标 定, 大幅度降低企业的研发成本、生产成本, 产品 品质也立即提升到国际一流水准。
ROUT
RXD
VOUT
GND GND
7NE电压输出型 VCC
连接采样单片机 RXD TXD 信号采样口 GND +5V
4-m2A0
VOUT 7NE电流输出型 GND
VCC
信号采样口
采样电阻
GND
+2V4
引脚定义PIN DEFINITION
BOTTOM VIEW
引脚 1 2 3 4 5 6 7
名称 定位 VCC GND VOUT RXD TXD RDE
T T L (标 配 ）0.4-2.0V D C (常 规 ）/4-20m A
数 据 位:8;停 止 位:1;校 检 位:无;
英国威斯通D500系列说明书
Page 8 of 11
烟气颗粒物检测仪 D-508 说明书
2.2 软件设定
电气连接完毕后，大概需要 10 到 15 分钟的操作准备时间，
按钮 Ent：进入菜单，每按一次进入下一个菜单；
按钮+：参数增加；
按钮ቤተ መጻሕፍቲ ባይዱ：参数减小
菜单默认密码是 111，按 ENT 进入。密码 508 可进入 F 以后的高级菜单。
表 2-2 输出对应表
Version 1.0
Page 10 of 11
烟气颗粒物检测仪 D-508 说明书
3 日常维护
因为 D-508 特殊的设计，粘附在探杆上的粉尘不会对测量造成任何影响，因此需要的维护工 作非常低。可能造成仪器测量不准的主要因素在于机组投运时，燃烧大量汽油，汽油燃烧后的胶 质包裹探杆造成一定的测量误差，这时只需拔出探杆擦拭即可，必要时可以用细砂纸进行处理。
模拟量输出信号
负载 报警限值 1 报警限值 2
230 / 110 VAC, 50 – 60 Hz 10 到 15 分钟
138x 175 x 62 mm 1200 mm ca. 4,5 kg IP 65 -20 °C ... +60 °C
0 … 100 %；0～10mg/m3；0～1000mg/m3 1%
2、 设定工作模式； 3、 设定报警限值；
Version 1.0
Page 7 of 11
烟气颗粒物检测仪 D-508 说明书
图 2-1 接线示意图 端子 1: 220V 电源 L 端子 2: 220V 电源 N 端子 3: 接地 PE 端子 4: 4～20mA 信号正端 FB+ 端子 5: 4～20mA 信号正端 FB端子 6: 无 端子 7: 无 端子 8: 报警限值 2 GW2 端子 9: 报警限值 2 GW2 端子 10: 报警限值 1 GW1 端子 11: 报警限值 1 GW1
气体检测仪产品参数
产品描述：
一氧化氮NO检测变送器是可以应用于一氧化氮泄漏场所，采用电化学式技术，具有信号稳定，精度高等优点，方式适用于各种危险场所。
2、产品特性：
先进的微处理器技术，防爆设计，快速，可信，稳定。3.6V锂电池电源供电，反应速度快，测量精度高，最佳的性能和较低费用。
3、技术参数：
检测气体：一氧化氮（NO）量程：0-250ppm，精度：＜±5%(F.S)，最小读数：1ppm，响应时间：≤60秒，传感器寿命：24个月，传感器类型:电化学式，电源：3.6V锂电池供电，检测方式：扩散式，工作方式：连续工作200小时，输出信号：三线制4-20mA模拟信号输出,RS485输出（选配），连线方式：便携式显示：大屏幕液晶显示，报警：声光报警，防爆标志：Ex dIICT3，防护等级：IP65，工作温度：-10～40℃（特殊要求根据需要而定），工作湿度：5-90%RH，尺寸：126mm×66mm×32mm，重量：220g
氧气检测仪
产品描述：
氧气O2体检测变送器是可以应用于氧气泄漏场所，采用电化学式技术，具有信号稳定，精度高等优点，方式适用于各种危险场所。
2、产品特性：
先进的微处理器技术，防爆设计，快速，可信，稳定。3.6V锂电池电源供电，反应速度快，测量精度高，最佳的性能和较低费用。
3、技术参数：
检测气体：氧气（O2）量程：0-30%VOL，精度：＜±5%(F.S)，最小读数：1%VOL，响应时间：≤15秒，传感器寿命：24个月，传感器类型:电化学式，电源：3.6V锂电池供电，检测方式：扩散式，工作方式：连续工作200小时，输出信号：三线制4-20mA模拟信号输出,RS485输出（选配），连线方式：便携式显示：大屏幕液晶显示，报警：声光报警，防爆标志：Ex dIICT3，防护等级：IP65，工作温度：-10～40℃（特殊要求根据需要而定），工作湿度：5-90%RH，尺寸：126mm×66mm×32mm，重量：220g
气体检测传感器产品介绍---CITY
电化学传感器—有毒气体传感器
电化学毒气传感器是一种微燃料电池元件，不必保养而可以有长期 的稳定性。它是在原有的氧气传感器的基础上改进而得。
催化珠传感器
Pellistors使用催化燃烧来测量可燃气体或蒸气在空气的含量直到达 到该气体的LEL* 。
红外传感器
正如人们所知： • 很多材料能吸收红外辐射（由于分子内振动） • 对任何一种材料，它的吸收能力随波长（它的吸收光谱）变化而变化 • 不同材料有不同的吸收光谱
4系列传感器
7系列传感器
公司主要客户及相关型号
环境保护气体检测： 相关应用设备: 烟气污染源检测仪器,汽车尾气分析仪器。 主要客户: 崂山应用技术有限公司,浙江浙大鸣泉科技有限公司 主要型号: NO传感器(NX1,3NF/F); 氧气传感器(AO2,7OXV,5FO); SO2传感器(3SF/F); NO2传感器(3ND); CO传感器(3F/F); 医疗 ： 相关应用设备: 矿井下的有毒气体检测,可燃气体检测设备。 主要客户:深圳迈瑞生物医疗股份有限公司，北京谊安医疗系统股份有限公司 主要型号:氧气传感器(MOX-2,MOX-4,AO2,7OXV)
气体传感器主要性能指标
• • • 传感器的稳定性： 在特殊应用环境下的稳定性、整个生命周期内的稳定性。 传感器的反应时间(通常是T90)。 传感器的量程及精度。
•
• • • •
传感器的使用寿命。
传感器的鲁棒性（抗干扰,2,3,5,MOX等系列. 传感器的复位时间。
竞争情况
谢谢!
MOX系列传感器
3系列传感器
竞争情况
CITY产品所涉及的行业已经成熟稳定,近年来行业内的竞争也越来越 激烈。
行业 煤炭气体安全 工业气体安全 竞争品牌 ALPHASENSE NEMOTO ALPHASENSE MENBRAPOR RAE 环保设备 IT ALPHASENSE 费加罗 医疗 VENTEX 费加罗 主要代理商 深圳新世联 北京长英科技 深圳新世联 深圳富安达 上海孚兴，上海首 亨，昆山诺金 深圳富安达 深圳新世联 深圳富安达 威海诺金 深圳富安达 主要产品 O2，有毒气体 CO O2，有毒气体 氨气 CO,H2S O2，NO SO2，NO2， CO O2 O2 O2 产地 英国 日本 英国 瑞士 上海 德国 英国 日本 美国 日本
费加罗技研株式会社 EC01 气体传感器评价试验箱 操作使用说明书
１．安全注意事项２．使用注意事项３．部件名称及功能概述４．测试准备５．测试方法６．规格目次欢迎购买使用气体传感器评价试验箱（EC01），对此我们表示由衷的感谢！请在仔细阅读本操作使用说明书后正确使用本产品。
１１２４６８费加罗技研株式会社EC01（气体传感器评价试验箱）操作使用说明书(1)(2)(3)(4)1. 安全注意事项请务必遵守2. 使用注意事项本产品是一种简易型的试验箱。
使用时请仔细盖紧盖板不能留有缝隙。
如果要进行很精确的气体测试时，请选用比本产品气密性更高的试验箱。
测试时如果将类似于气体报警器这样体积较大的设备放入试验箱的话，可能因为试验箱的有效容积减少而导致气体浓度制备出现误差。
由于氨气、VOC 、有机溶剂蒸汽等吸附性很强的气体很容易吸附在试验箱的内壁之上，因此本产品不适用于这些气体的测试用途。
吸附于箱内壁的气体液化后，有可能导致试验箱内的气体浓度下降。
有必要对吸附性很强的气体进行测试时，请选用箱内壁采用了气体不容易附着材质的试验箱，或对箱内壁进行过涂层处理的试验箱。
如果已经向本试验箱内注入了吸附性很强的气体，为了在使用后去除附着的气体，请用酒精擦拭试验箱内部，然后对内部用洁净空气进行长时间换气等的妥善处置。
如果在高温、低温或极度的低湿度与高湿度的室内环境进行测试的话，气体传感器的测定值可能会受到影响。
请在测试前对各型号传感器规格进行确认。
本试验箱没有防爆设计。
请勿在对气体爆炸下限为(LEL) 50％以上浓度的可燃性气体进行测试时使用。
本试验箱无法保证绝对完全的密闭状态。
请勿在对可能危及人身安全的高浓度毒性气体进行测试时使用。
在用于对可燃性气体进行测试时请务必注意防火措施，同时试验箱向外排气时请在可以充分换气的场所进行。
而且，为确保安全，请考虑采取设置气体报警器等措施。
尤其是在用于对毒性气体进行测试的用途时，请务必在能够保证充分换气的场所进行。
另外出于安全考虑，将试验箱中的气体排出时请注意避免人员吸入的同时，请在室外或排风罩内进行操作。
gasbadge pro hcn氰化氢气体检测仪(智能传感器)bw gaxtzdl氰化氢检测仪
GasBadgeProHCN氰化氢气体检测仪(智能传感器)BWGAXT-Z-DL氰化氢检测仪HCN检测仪GasBadgeProHCN氰化氢气体检测仪(智能传感器)RL010845BWGAXT-Z-DL氰化氢检测仪HCN检测仪RL010850图片型号:RL010845搜索：『润联网』查价格型号:RL010850搜索：『润联网』查价格GasBadgeProHCN氰化氢气体检测仪(智能传感器)RL010845BWGAXT-Z-DL氰化氢检测仪HCN检测仪RL010850内容型号:RL010845GasBadge®Pro以英思科最高质量及可靠性标准设计，提供终身的危险气体保护，功能多于任何其他现有单气体检测设备。
可替换使用的“智能”传感器使GasBadge®Pro能够快速适应监测器识别为非安全级别的氧气或下列任何有毒气体：一氧化碳、硫化氢、二氧化氮、二氧化硫、氯、二氧化氯、磷化氢、氨、氰化氢及氢等。
GasBadge®Pro通过红外接口直接向选配附件通信，如DockingStation™、数据连接（Datalink）、及红外打印机，继续简化并自动化标定过程、功能（冲击）测试及数据下载。
标准短期暴露水平（STEL）、时间加权平均值（TWA）及长达一年的调查数据记录功能，另配有可记录最近15次告警事件的事件记录器。
该产品配以防震外壳，不受无线电频率干扰，并具有防水及经久耐用的特点。
防震保护层保护产品不受各类恶劣工作环境的损害。
其易用而灵敏的四键式导航可轻松实现安装设置、操作、及校准功能。
型号:RL010850GAXT-Z-DL氰化氢检测仪简要说明：GasAlertExtreme以舒适耐用为设计理念，它具有多种有效的有毒气体模式，能够可靠地监控任何单一有害气体。
通过简单的开/关操作，这种单一气体探测器利用可现场更换的2年型电池和传感器提供长久的使用寿命。
校准是一个简单的自动化程序，并与BW的MicroDockII自动测试和校准系统兼容。
CROWCON气体检测仪
英国CROWCON气体检测仪
上海智川工贸有限公司优惠供应英国CROWCON气体检测仪、CROWCON气体检测仪器、CROWCON等；
CROWCON采用固定式气体检测探头来检测氧气、毒气和可燃气体XgardType1：本安型毒气/氧气检测探头XgardType2：隔爆型毒气/氧气检测探头XgardType3：隔爆型可燃气体检测探头XgardType4：隔爆型高温可燃气体检测探头XgardType5：隔爆型标准输出型可燃气体检测探头XgardTyp；CROWCON四合一便携式气体检测仪是可信赖的个人用气体检测仪，一键式操作、简单方便、防滑、防水、适合于各种工业环境使用，单次充电可使用16小时，清晰的菜单指示，可对整个事件和数据进行记录。
英国CROWCON气体检测仪
上海智川工贸有限公司优惠供应英国CROWCON气体检测仪、CROWCON气体检测仪器、CROWCON等；
CROWCON采用固定式气体检测探头来检测氧气、毒气和可燃气体XgardType1：本安型毒气/氧气检测探头XgardType2：隔爆型毒气/氧气检测探头XgardType3：隔爆型可燃气体检测探头XgardType4：隔爆型高温可燃气体检测探头XgardType5：隔爆型标准输出型可燃气体检测探头XgardTyp；CROWCON四合一便携式气体检测仪是可信赖的个人用气体检测仪，一键式操作、简单方便、防滑、防水、适合于各种工业环境使用，单次充电可使用16小时，清晰的菜单指示，可对整个事件和数据进行记录。
英国凯恩km940烟气分析仪中文操作说明书
如果在操作中错按了 ，在倒计时未到 0 前，按
便可回到正常操作状态。
4.8 电磁相容性
KM940 完全遵守欧洲议会的 89/336/EEC 条款，条款规定任何电子设备运行时产生 的电磁干扰都必须低于规定的标准，且必须防电磁干扰。
10
KM940 操作手册
5. 菜单操作
5.1 基本操作 主显示页面
按
进入主菜单
由于烟道气中可能含有易挥发的有毒物质，使用本仪器一定要在通风良好的地方,操 作人员必须经过严格的操作培训。
3. 首次使用
充电 12 小时
检查仪器备件是否齐全
仔细阅读本手册
当你首次使用这台仪器时，你必须先选择设定：
语言选择 倒计数校准时间 数据格式 RS232 传送速率 日期和时间 打印输出抬头和电话号码
5
4 . 正常开机过程………………..…………………………………..
6
4.1 每次使用前的准备工作………………………………...
6
4.2 自动校准………………………………………………...
6
4.3 主页面示参数…………………………………………...
8
4.4 烟道气采样……………………………………………...
按
或
上下移动光标
按
进入子菜单
按
选择参数
用
或
更改设定
按
确定并移动到下一个参数
NETT C . . . . 0.0 O2 % . . . . 20.9 CO ppm . . 0000 EFF(G) % . . . . 0.0
MAIN MENU
1. SELECT 3.DISPLAY 2.UNITS 4.SETUP
Ventis MX4多气体检测器说明书
PUMP UP YOURGAS DETECTION PROGRAMConfigured for your safety, theVentis™ MX4 multi-gas detector takesyour gas detection program to thenext level.■ Detect from one to four gases witha wide range of sensor options■ Draw samples from up to 100 feetwith an optional, integrated samplingpump■ Gain increasedinstrument visibilitywith a safety orangeovermold■Realize true portabilitywithmulti-gas protection insingle-gas size■ Use the extendedrange battery for up to20 hours (without pump)■ Discover a better way to do gasdetection with the Ventis on iNet®Build your Ventis today at/ventisbuilder5.When iNet detects a problem, Industrial Scientific rushes areplacement gas detector to you.4.iNet emails real-time alerts and status reports.3.iNet Control provides visibility into your gas detection programvia the Internet.1.Operators dock gas detectors owned by Industrial Scientific.2.Docking stations perform bump tests, calibrationsand record keeping.HOW GAS DETECTION AS A SERVICE WORKSIMAGINE YOUR PEACE OF MIND... IMAGINE iNETCONFIGURATION OPTIONSVENTIS MX4 INTEGRAL PUMP MA TRIX EXAMPLE : VTSP-0011 - Ventis MX4 Pump, No Bat-VTSP-011VTSP-0011 PUMPBuild and price your Ventis online with the Ventis MX4 instrument builder./ventisbuilderMOST COMMON INSTRUMENT CONFIGURA TIONS PART NO.DESCRIPTIONVTS-K1231100y0z Ventis - LEL, CO, H 2S, O 2, Li-ion, desktop charger, BlackVTS-K1231201y0z Ventis - LEL, CO, H 2S, O 2, Li-ion, desktop charger/datalink, Safety OrangeVTS-K5231300y1z Ventis - LEL, SO 2, H 2S, O 2, Li-ion, auto charger, soft case, Black VTS-K1031301y0z Ventis - LEL, CO, O 2, Li-ion, auto charger, Safety Orange VTS-K1431000y1z Ventis - LEL, CO, NO 2, O 2, Li-ion, no charger, soft case, Black VTS-K1232111y0z Ventis with pump - LEL, CO, H 2S, O 2, Extended Li-ion, desktop charger, Safety OrangeVTS-K1232110y1z Ventis with pump - LEL, CO, H 2S, O 2, Extended Li-ion, desktop charger, soft case, BlackVTS-L1232110y2z Ventis with pump - LEL (methane), CO, H 2S, O 2, Extended Li-ion, desktop charger, hard case with display window, BlackVTS-K5232111y0zVentis with Pump - LEL, SO 2, H 2S, O 2, Extended Li-ion, desktop charger, Safety OrangeVTSP-2011 PUMPORDERING INFORMATIONCONFINED SPACE KITS WITH INTEGRAL PUMP PART NO.VK-K123211xy1z Ventis Confined Space Kit - LEL, CO, H VK-K103211xy1z Ventis Confined Space Kit - LEL, CO, O VK-K023211xy1z Ventis Confined Space Kit - LEL, H2S, O VK-K003211xy1zVentis Confined Space Kit - LEL, O x = Instrument Color: 0 = Black, 1 = Safety Orangey = A gency Certification: 1 = UL/CSA, 2 = ATEX/IECEx, 3 = MSHA, 4 = ANZEx,5 = CHINA EX, 7 = GOST-R/GOST-K, 8 = KOSHA, 9 = INMETRO, A = MED, D = TIIS z = L anguage for included Reference Guide: 1 = EN, 2 = FR, 3 = ES, 4 = DE, 5 = ITA,6 = DUT,7 = PT, 9 = RUS, A = POL, B = CZE, C = CN, D = DAN, E = NOR, F = FIN, G = SWE, J = JPN Ventis Confined Space Kits with Integral Pump Include: Ventis with intergral pump, universal charger, soft carrying case, reference guide, calibration tubing, dustfilter/water stop, calibration fitting, sample tubing, calibration gas (appropriate mix) with regulator, rugged hard plastic case.CONFINED SPACE KITS WITH SLIDE-ON PUMP MA TRIX PART NO.DESCRIPTIONVKVSP4-ABCDEFVentis Confined Space Kit with Ventis Slide-on Pump (LEL, CO, H 2S, O 2)A = LEL Sensor Calibration: K = Pentane, L = MethaneB = Instrument Color: 0 = Black, 1 = Safety OrangeC = Monitor Battery: 1 = Lithium-ion, 2 = Extended Range Lithium-ion, 3 = AlkalineD = Pump Battery: 1 = Lithium-ion, 2 = Extended Range Lithium-ionE = Agency Certification: 1 = UL/CSA, 2 = ATEX/IECEx, 3 = MSHA, 9 = INMETROF = D ocumentation Language: 1 = EN, 2 = FR, 3 = ES, 4 = DE, 5 = ITA, 6 = DUT, 7 = PT, 9 = RUS, A = POL, B = CZE, C = CN, D = DAN, E = NOR, F = FIN,G = SWE Ventis Confined Space Kits with Slide-on Pump Include: Ventis with LEL, CO, H 2S, and O 2 sensors, Ventis Slide-on Pump, 110 VAC desktop charger for each rechargeable instrument ordered (max of 2), calibration cup and tubing with T-fitting, dust filter/water stop, 10 feet of sample tubing, 34 liter cylinder of calibration gas, manual regulator, rug-ged hard plastic carrying caseTHE VENTIS IS PARTICULARLY USEFUL IN THE FOLLOWING INDUSTRIES:■ Chemical ■ Construction■ Electrical / Gas Utilities ■ Fire Service■ Oil and Gas ■ Public Works ■ Steel Production ■ W ater / Waste Water T reatment18108631-00 V·CAL WITH VENTIS INSTRUMENT* (*monitor not included)18108191 VENTIS CHAR GER18108650-06-UNIT CHARGER18108209 CHARGER/DA T ALINK18107763 PRINTER18108652TRUCK-MOUNTCHAR GER , WITH PLUG18108651AUTOMOTIVE CHARGERACCESSORIESPART NO .DESCRIPTION18109327-ABC DSX ™ Docking Station for Ventis ™ MX4A – DSX Mode:0 = DSX Standalone171344871715556417134495171345031714359517148313-117148313-217148313-317148313-41715060818108653 TR UCK-MOUNT CHARGER, HAR D WIR ED18108631-10 V·CAL WITH VENTIS WITHPUMP INSTRUMENT* (*monitor not included)18109327 DSX DOCKING ST A TION WITH VENTIS MX4* (*monitor not included)REV 0715© 2015 Industrial Scientific CorporationINSTRUMENT WARRANTY:Two-year warranty, including sensors and battery CASE MATERIAL:Polycarbonate with protective rubber overmold DIMENSIONS:103 mm x 58 mm x 30 mm (4.1” X 2.3” X 1.2”) - Ventis, lithium-ion battery version172 mm x 67 mm x 66 mm (6.8” X 2.6” X 2.6”) - Ventis with pump, lithium-ion battery version WEIGHT:182 g (6.4 oz) - Ventis, lithium-ion battery version380 g (13.4 oz) - Ventis with pump, lithium-ion battery version OPERATING TEMPERATURE RANGE: -20°C- 50°C (-4°F-122°F)OPERATING HUMIDITY RANGE:15%-95% Non-condensing (continuous)DISPLAY/READOUT:Backlit liquid crystal display (LCD)POWER SOURCE/RUN TIME:Rechargeable lithium-ion battery pack (12 hours typical @ 20ºC) - VentisRechargeable extended-range lithium-ion battery pack (20 hours typical @ 20ºC) - Ventis(12 hours typical @ 20ºC) - Ventis with pump Replaceable AAA alkaline battery pack (8 hours typical @ 20ºC) - Ventis(4 hours typical @ 20ºC) - Ventis with pump ALARMS:Ultra-bright LEDs, loud audible alarm (95 dB at 30 cm) and vibrating alarm SENSORS:Combustible gases/methane - Catalytic diffusion O 2, CO, CO/H 2 low, H 2S, NO 2, SO 2 - Electrochemical MEASURING RANGES: Combustible gases: 0-100% LEL in 1% increments Methane (CH 4): 0-5% of vol. In 0.01% increments Oxygen (O 2): 0-30% of vol. In 0.1% increments Carbon monoxide (CO/H 2 low): 0-1,000 ppm in 1 ppm increments Carbon monoxide (CO): 0-1,000 ppm in 1 ppm increments Hydrogen sulfide (H 2S): 0-500 ppm in 0.1 ppm increments Nitrogen dioxide (NO 2): 0-150 ppm in 0.1 ppm increments Sulfur dioxide (SO 2): 0-150 ppm in 0.1 ppm incrementsCERTIFICATIONS:UL: Class I, Division 1, Groups A B C D, T4; Zone 0, AEx ia IIC T4 Class II, Groups F G (Carbonaceous & Grain dust); IP66; IP67ATEX: Ex ia IIC T4 Ga and Ex ia I Ma; Equipment Group and Category II 1G and I M1; IP66; IP67IECEx: Ex ia IIC T4 Ga; IP66; IP67CSA: Class I, Division 1, Groups A B C D, T4; Ex d ia IIC T4 C22.2 No. 152 for %LEL reading only ANZEx: Ex ia s Zone 0 I/IIC T4; IP66; IP67INMETRO: Ex ia IIC T4 Ga; IP66; IP67KOSHA: Ex d ia IIC T4MSHA: 30 CFR Part 22; Permissible for underground mines; Li-ion versions onlyPA-DEP: Permissible for PA Bituminous Underground Mines CHINA EX: Ex ia d IIC T4 Gb CHINA CMC: Metrology approvalCHINA MA: Approved for underground mines; Alkaline version onlyChina KA: Ex ia d I Mb, diffusion (without pump) Alkaline version only GOST- K: PBExdiaI X / 1ExdiaIICT4 X GOST-R: PBExdiaI X / 1ExdiaIICT4 XMED: Portable Multigas Detector; Category 2 (MED 2012/32/EU); Li-Ion only Charger/Docking Station accessories; category 1SANS-1515: SANS 1515-1; Type A; Ex ia I/IIC T4 IP66/67; Li-Ion only TIIS: Ex ia IIC T4 X SUPPLIED WITH MONITOR:Calibration Cup (Ventis), Sample Tubing (Ventis with pump), Ventis MX4 Reference GuideREFERENCE GUIDE LANGUAGE:English (1), French (2), Spanish (3), German (4), Italian (5), Dutch (6), Portuguese (7), Russian (9), Polish (A), Czech (B), Chinese (C), Danish (D), Norwegian (E), Finnish (F), Swedish (G), Japanese (J)* These specifications are based on performance averages and may vary by instrument.SPECIFICATIONS*ASIA PACIFICPhone: +65-6561-7377 Fax: +65-6561-7787**************.comAMERICASPhone: +1-412-788-4353 | Fax: +1-412-788-8353 1-800-DETECTS (338-3287) North America***************EMEAPhone:+33 (0)1 57 32 92 61Fax: +33 (0)1 57 32 92 67**************.com。
英国CITY氧气传感器 T7OXV气体探测器
T7OXV CiTiceL ®Technical Specifications7OXV0-25%vol. O 2None4-20 mA d.c.<15 Seconds at 20°C0.1%vol O 2Can be considered linear inmany cases. Refer to OP-05 for further details Product DimensionsAll dimensions in mmAll tolerances ±0.15 mm unless otherwise statedIMPORTANT NOTE:All performance data is based on conditions at 20°C, 50% RH and 1013 mBar. For further information on the operation and calibration of the T7OX/V 4-20mA transmitter, please refer to OP-05.Oxygen (O 2) Gas Sensor with 4-20 mA TransmitterProduct Code : TA2R-1AMEASUREMENTSensor Type Used Measurement Range Filter Output Response Time (T 95)Resolution Linearity 10 - 35 VDC15 M ΩVia built-in span potentiometerELECTRICALPower Supply Required Output Impedance Calibration Via mounting nose supplied Approx. 120 g includingmounting accessoryNoneMECHANICALMounting Weight Position Sensitivty -20°C to +50°C 0°C to 20°C Refer to OP-05Atmospheric ± 10%0.02% signal/mbar0 - 99% RH non-condensingENVIRONMENTALOperating Temperature Range Recommended Storage Temp Temperature Compensation Operating Pressure RangePressure Coefficient Operating Humidity Range<5% signal loss/year Two years in air6 months in CTL container24 months from date of despatch(This ammounts to a variation ofcondition 6 of our standard terms and conditions which otherwise apply)LIFETIMELong Term Sensitivity Drift Expected Operating LifeStorage LifeStandard WarrantyKey Features & Benefits:• Robust 3-Series packaging• Industry standard 4-20 mA outputPoisoningCiTiceLs are designed for operation in a wide range of environments and harsh conditions. However, it is important that exposure to high concentrations of solvent vapours is avoided, both during storage, fitting into instruments and operation.When using sensors with printed circuit boards (PCBs), degreasing agents should be used before the sensor is fitted. Do not glue directly on or near the CiTiceL as the solvent may cause crazing of the plastic.Cross Sensitivity TableToxic gases at TLV levels will have no cross-sensitivity effect on Oxygen CiTiceLs. At very high levels (i.e. percent levels), highly oxidising gases (e.g. ozone and chlorine) will interfere to the extent of their oxygen equivalent, but most other commonly occurring gases will have no effect. For example: Methane 100% 0 Hydrocarbons 100% 0 Hydrogen 100% < -2% Carbon monoxide 20% < -0.5%Acid gases such as CO 2 and SO 2 will be slightly absorbed by the electrolyte and tend to increase the flux of oxygen to the electrode. This gives an enhanced oxygen signal of about 0.3% of signal per 1% CO 2. Capilliary controlled CiTiceLs (such as the 7OX/V) are not suitable for continuous operation in concentrations of CO 2 above 25%. In applications where high concentrations of CO 2 are present, the AO2 CiTiceL is recommended.The cross-sensitivity values quoted are based on tests conducted on a small number of sensors. They are intended to indicate sensor response to gases other than the target gas. Sensors may behave differently with changes in ambient conditions and any batch may show significant variation from the values quoted.Every effort has been made to ensure the accuracy of this document at the time of printing. In accordance with the company’s policy of continued product improvement City Technology Limited reserves the right to make product changes without notice. No liability is accepted for any consequential losses, injury or damage resulting from the use of this document or from any omissions or errors herein. The data is given for guidance only. It does not constitute a specification or an offer for sale. The products are always subject to a programme of improvement and testing which may result in some changes in the characteristics quoted. As the products may be used by the client in circumstances beyond the knowledge and control of City Technology Limited, we cannot give any warranty as to the relevance of these particulars to an application. It is the clients’ responsibility to carry out the necessary tests to determine the usefulness of the products and to ensure their safety of operation in aSAFETY NOTEThis sensor is designed to be used in safety critical applications. To ensure that the sensor and/or instrument in which it is used, are operating properly, it is a requirement that the function of the device is confirmed by exposure to target gas (bump check) before each use of the sensor and/or instrument. Failure to carry out such tests may jeopardize the safety of people and property.。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
NX1 CiTiceL ®
Technical Specifications
3-electrode electrochemical 0-5,000 ppm NO
To remove effect of SO 2 in gas
stream
0.05 ± 0.01 µA/ppm
<8 Seconds at 20°C 0 to +12 ppm equivalent <30 ppm equivalent
Dependent on electronics
(1 ppm when used with recommended electronics)
2% of signal
Linear Product Dimensions
All dimensions in mm
All tolerances ±0.15 mm unless otherwise stated
IMPORTANT NOTES:
Prolonged exposure to high or low humidity may lead to an increased response time.
Connection should be made via PCB sockets only. Soldering to the pins will seriously damage your sensor and invalidate the warranty.All performance data is based on conditions at 20°C, 50% RH and 1013 mBar, using City Technology recommended circuitry. For sensor performance data under other conditions, contact City Technology.
Nitric Oxide (NO) Gas Sensor
Part Number: AF747-B05
MEASUREMENT
Operating Principle Measurement Range Filter Sensitivity Response Time (T 95)Baseline Offset (clean air)Zero Shift (0°C to +40°C)Resolution Repeatability Linearity 10 Ω
+300 mV
ELECTRICAL
Recommended Load Resistor Bias Voltage 32 g (nominal)
ABS
Any
MECHANICAL
Weight Housing Material Orientation -20°C to +50°C
0°C to 25°C in CTL packaging 800 to 1100 mBar 0.02% signal/mBar
15 to 90% RH non-condensing
ENVIRONMENTAL
Operating Temperature Range Recommended Storage Temp Operating Pressure Range
Pressure Coefficient Operating Humidity Range
Typically <5% signal loss/year
6 months in CTL container
15 months from date of despatch
LIFETIME
Long Term Sensitivity Drift Storage Life Standard Warranty Key Features & Benefits:
• Designed for Automotive Applications •
Fast Response
(+V)1234
(Common)(-V)(V out)
PIN CONFIGURATION OF AUTO NO NX1SENSOR
VIEW FROM ABOVE
Red Green Black Yellow
Automotive NX1 CiTiceL ® Part Details
MOLEX HEADER (0.100"/2.54mm)
Molex Part Number 22-29-2041CRIMP TERMINAL HOUSING (MATING PART)
Molex Part Number 22-01-2045
深圳市深国安电子科技有限公司
地址：广东省深圳市龙华新区牛栏前大厦Ｃ５０７
网址：ｗｗｗ．ｓｉｎｇｏａｎ．ｃｏｍ ｗｗｗ．ｓｉｎｇｏａｎ．ｃｏｍ．ｃｎ ｗｗｗ．ｓｈｅｎｇｕｏａｎ．ｃｏｍ
蒋小姐：１３４ ２８７６ ２６３１ 电话：８６ ７５５－８５２５８９００
Note:All resistors 1%unless indicated
Recommended External Circuit for Sensor
This diagram shows the recommended operating circuit for the NX1 CiTiceL, designed to give an output of 0-5 V over the range 0-5000 ppm, where the sensitivity is 60 nA/ppm.
Typical Span Output vs Temperature (°C)
S p a n O u t p u t (% 20°C O u t p u t )
Temperature (°C)
-10
10040
30
20
10
50
909294
9698102104106
mean 20% output
+3SD
-3SD
网址：ｗｗｗ．ｓｉｎｇｏａｎ．ｃｏｍ ｗｗｗ．ｓｉｎｇｏａｎ．ｃｏｍ．ｃｎ ｗｗｗ．ｓｈｅｎｇｕｏａｎ．ｃｏｍ
蒋小姐：１３４ ２８７６ ２６３１ 电话：８６ ７５５－８５２５８９００
Poisoning
CiTiceLs are designed for operation in a wide range of environments and harsh conditions. However, it is important that exposure to high concentrations of solvent vapours is avoided, both during storage, fitting into instruments and operation.
When using sensors with printed circuit boards (PCBs), degreasing agents should be used before the sensor is fitted. Do not glue directly on or near the CiTiceL as the solvent may cause crazing of the plastic.
SAFETY NOTE
Although this product is not designed for use in life safety applications, if it is used in such applications it is
a requirement that the function of the device is confirmed by exposure to target gas (bump check) before
each use of the sensor and/or instrument, to ensure that the sensor and/or instrument in which it is used, are operating properly. Failure to carry out such tests may jeopardize the safety of people and property.
深圳市深国安电子科技有限公司
地址：广东省深圳市龙华新区牛栏前大厦Ｃ５０７
蒋小姐：１３４ ２８７６ ２６３１ 电话：８６ ７５５－８５２５８９００
网址：ｗｗｗ．ｓｉｎｇｏａｎ．ｃｏｍ ｗｗｗ．ｓｉｎｇｏａｎ．ｃｏｍ．ｃｎ ｗｗｗ．ｓｈｅｎｇｕｏａｎ．ｃｏｍ。