图纸常用英语模板
图纸常用英语模板
复合剖视compound section剖面图section, sectional view重合剖面coincide section, revolved section移出剖面removed section剖面线section line剖面符号symbols for section-lining习惯画法conventional drawing局部放大图drawing of partial enlargement零件图detail drawing, working drawing第三角投影third angle projection粗实线continuous thick line, full line, visible line细实线continuous thin line虚线dot line, dashed line, hidden line点划线dash and dot line双点划线double dots line波浪线断裂线break line剖切平面迹线cutting plane line尺寸线dimension line尺寸界线extension tine尺寸dimension size箭头arrowhead基准datum基准线datum line基准面datum plane中心孔central hole中心距center distance轴shaft, axle孔hole斜孔inclination装配图assembly drawing性能尺寸characteristic dimension大小尺寸size dimension总体尺寸外形尺寸outer dimension配合尺寸fit dimension内圆角fillet外圆角round尖角sharp corner倒角chamfer轮缘flange of wheel缘、边、环rim轴肩shoulder凸台boss凹坑concave pit轴颈shaft neck轮毂hub 轮辐spoke, spoke of wheel直纹滚花straight knurling s网纹滚花hatching knurling键槽key-way退刀槽escape拔模斜度pattern draft填料盒gland box油槽oil groove油封oil seal标准件standard parts螺纹thread外螺纹external thread内螺纹internal thread大径major diameter小径minor diameter螺距pitch of thread牙型form of thread旋向direction of turning右旋螺纹right-hand thread左旋螺纹left-hand thread头数number of thread导程lead粗牙coarse thread细牙fin thread螺栓bolt螺钉screw螺柱stud螺母nut垫片washer公差tolerance公差带tolerance zone零线zero line标准公差standard tolerance公差等级tolerance grade基本偏差fundamental deviation配合fit间隙配合clearance fit过盈interference过盈配合interference fit过渡配合transition fit基孔制hole-basic system of fits基轴制shaft-basic system of fits间隙clearance形状公差tolerance in form, form tolerance 直线度straightness平面度flatness圆度roundness圆柱度cylindricity线轮廓度profile of any line面轮廓度profile of any plane位置公差tolerance in position, position tolerances平行度parallelism齿轮gear圆柱齿轮cylindrical gear正齿轮spur gear斜齿轮spiral gear轮齿gear tooth节圆pitch circle齿顶圆addendum circle, outside circle齿根圆root circle, addendum circle模数modulus齿数number of teeth齿高tooth height齿顶高height of addendum齿根高height of addendum齿厚circular thickness齿间tooth space齿宽tooth width压力角angle of pressure弹簧spring销pin圆柱销round pin圆锥销taper pin开口销cotter pin, split键key平键flat key半圆键half round key, woodruff key轴承bearing滚动轴承rolling bearing向心铀承radial bearing密封装置sealing equipment锁紧装置locking equipment粗糙度roughness基本尺寸basic size实际尺寸actual size极限尺寸limits size最大极限尺寸maximum limit of size最小极限尺寸minimum limit of size偏差deviation上偏差upper deviation下偏差lower deviation垂直度perpendicularity倾斜度angularity同轴度concentricity对称度symmetry 位置度true position跳动run-out圆跳动cycle run-out全跳动total run-out轴测投影axonometric projection轴测投影面plane of axonometric projection 轴测图axonometric drawing正等轴测投影isometric projection正二测bimetric projection斜二测oblique bimetric projection轴测轴axonometric axis轴间角axis angle, angle between ales缩短foreshortened轴向缩短率coefficient of axial deformation ratio offore shortening for any axis切割法cutting method, by cutting方箱法boxing method坐标法coordinate method方框法enclosing-square method四心近似法four-center approximate method机械工程图中常用的英语词汇Abbreviation 缩写Accuracy 精度、准确性Acme thread 梯形螺纹(29°)Addendum 齿顶高Addendum angle 齿顶角Addendum circle 齿顶圆Addendum of mating gear 啮合齿轮的齿顶高Adjacent-part lines 相邻零件线Aligned sections 旋转剖视Aligned view旋转视图Allowance 容差、加工余量Alloy 合金Alloy steel 合金钢Alphabet 字母Alteration 变更、更改Alternate-position views 位置改变的视图Alternator 交流发电机Induction alternator 感应(交流)发电机Motor alternator 电动(交流)发电机Single-phase alternator 单向(交流)发电机Synchronous alternator 同步(交流)发电机Three-phase alternator 三相(交流)发电机Amount 总量、总计Analyzable assembly 分析装配图Anchor bolt 地脚螺栓Angles 角Acute angle 锐角Blunt angle 钝角Right angle 直角Sliding angle 摩擦角Spiral angle 螺旋角Taper angle 锥角Angular 有角的Angular bearing 径向止推轴承Angular bevel gears 斜交伞齿轮Angular gear人字齿轮Angular section斜剖面Anneal 退火Approval 批准、许可Arc 弧、圆弧Arc thickness 弧长厚度(齿厚)Arc welding 弧焊Arrangement 布置、装置Arrangement of views 视图的布置Clamping arrangement 夹紧装置Cramping arrangement 紧固装置General arrangement 总体布置Arrow 箭头Arrowheads 箭头Assembly 装配图、组装图Assembly drawing 装配图Assembly drawing number 装配图图号Assembly for installation 安装图Assembly parts 组装配合零件Assembly sections 装配图剖视Assembly sketches 装配草图Auxiliary elevation 辅助立面图Auxiliary line辅助线Auxiliary section 辅助剖视Auxiliary surface 辅助面Auxiliary view 辅助视图Average 平均数Axial 轴的、轴向的Axial pitch 轴向节距Axial plane 轴向平面Axial thickness 轴向厚度Axis 轴线、中心线Axis of revolution 回转轴线Axis of rotation 旋转轴线Axis of symmetry 对称轴线Horizontal axis 水平轴Major axis 长轴Minor axis 短轴Vertical axis 垂直轴X axis X轴Y axis Y轴Axle 轴Axle bearing 轴向(止推)轴承Axle sleeve 轴向(止推)套筒Axonometric drawing 轴测图Babbitt 巴氏合金Back cone 背锥Back cone radius 背锥半径Back elevation 后视图Backstop 托架、棘爪Ball bearing 球轴承Bar 杆Angle bar 角钢Channel bar 槽钢Flat bar 扁钢Round bar 圆棒、圆钢Base 基础、底座、基线、基面、基准Base circle 基圆Base circular thickness 基圆弧线齿厚Base cylinder 基圆柱Base helix angle 基圆上的螺旋角Base plane 基平面Base point 基点Key base 键座Basic circle 基准圆Basic hole system 基孔制Base shaft system 基轴制Basic size 基本尺寸、公称尺寸、标称直径Basis 基础、基准、基线Battery 电池、蓄电池Bearing 轴承、支撑、方位Bearing accuracy 定位精度Bearing box 轴承箱Bearing brass 铜轴衬Bearing bridge 轴承支架Bearing oil seal 轴承油封圈Bearing support 轴承架Bearing unit 轴承组合件Anti-friction bearing 减摩轴承Ball and socket bearing 球窝轴承Conical bearing 锥形轴承Journal bearing 径向轴承Needle bearing 滚针轴承Plain bearing 滑动轴承Roller bearing 滚柱轴承Self-aligning bearing 自位轴承Thrust bearing 止推轴承Belt 带、皮带Bench 工作台Work bench 工作台Bend 弯头、接头Elbow bend 肘形弯管Normal bend 正弯管(90°)Bender 弯曲机Bending 挠曲Bending strength 抗弯强度Bent axle 曲轴Bevel 倾斜的、斜角的、斜面Bevel gear 圆锥齿轮、伞齿轮Bevel pinion 小圆锥齿轮Bevel washer 斜垫圈Bevel wheel 伞齿轮、斜摩擦齿轮Bilateral tolerance 双向公差Bill of materials 送料单Block in、block out 画草图Blue paper 蓝晒纸Blueprint 蓝图、设计图Board 板、(管理)局、厅Bottom board 底板Moulding board 模板Body 机体、机身Boiler 锅炉Bolt 螺栓、插销Adjusting bolt 调整螺栓Assembling bolt 装配螺栓Binding bolt 连接螺栓Bright blot 光制螺栓Captive bolt 固定螺栓Double-screw bolt 双头螺栓Fitter bolt 装配螺栓Foundation bolt 地脚螺栓Hexagonal head bolt 六角头螺栓Hook bolt 钩形螺栓Screw bolt 全螺纹螺栓Snap bolt 圆头螺栓Tension bolt 拉紧螺栓Bolted joints 螺栓连接Book 书、册Hand book 手册Instruction book 说明书Bore face machine 镗孔端面加工机床Borer 镗床Jig borer 坐标镗床Table borer 台式镗床Boring 镗孔Boring machine 镗床Boring mill 镗床Bottom case 底座Bottom clearance 径向间隙Bottom view 底视图Bracket 托架、支柱Brake 制动器、闸Brass 黄铜、铜轴衬Braze 铜焊Brazing 铜焊Breadth 宽度、厚度Break line 断裂线Brinell figure (number) 布氏硬度Brinell hardness 布氏硬度Broacher 拉床、绞孔机Broaching 扩孔机、拉床、拉削Broken circle 虚线圆Broken out section 断裂剖面Broken view 局部视图Bronze 青铜Burnishing 抛光、磨光Burr 三角矬、毛刺、去毛刺Bush 衬套、轴瓦Bushing 轴衬、衬套、套管Butt joint 对接焊Butterfly nut 蝶形螺母Butterfly valve 蝶形阀Button 按钮Push button 控制按钮Cable 电缆Cage 盒、罩、箱Caliper 卡尺、卡钳Gauge caliper 卡规、量规Internal caliper 内卡钳Sliding (vernier) caliper 游标卡尺Cam 凸轮Cam design 凸轮设计Cam shaft 凸轮轴Actuating cam 主动凸轮Adjustable cam 可调凸轮Control cam 控制凸轮Cap 盖、帽、罩Cap screw 带帽螺钉Capital 大写字母Carburizing 渗碳Card 卡片Cartographer 制图员Cartography 制图学、制图法Case 箱、盒、容器、表面Case hardened 表面淬火、硬化Nitrogen case hardening 渗氮硬化Casing箱、盒、壳Oil pump casing 油泵(壳) Casting 铸造、铸件Defect casting 铸件缺陷Die casting 压铸Sand casting 砂型铸造Spun casting 离心铸造Steel casting 铸钢Cast-iron 铸铁Castle circular nut 六角圆螺母Castle nut 蝶形螺母Catalogue data 表列数据Cave 凹槽、内腔Centre 中心、圆心Centre distance 中心距Centre hole 中心孔Centre line 中心线Centre-section 中心剖面Centre to centre 中心距Centesimal 百分的、百分之一的Centimeter 厘米、公分Central hole 中心孔Central plane 中心平面Central projection 中心投影Chafe 摩擦、磨损Chain 链Drive chain 主动链Transmission chain 传动链Chamfer 倒角、倒棱、斜面Dimensioning of chamfer 倒角的尺寸注法Changes on drawing 图的更改Channel 沟槽Chapter 章Chart 图表、计算图Chart of symbols 符号图表Auxiliary chart 辅助图Dimensions chart 外廓尺寸图Graphical chart 图表Process chart 工艺程序图Progress chart 工艺程序表、工作进度表Charting 制图(表)、填图Check 校验、校核、制动装置Check drawings 校图Check nut 防松螺母Check ring 挡圈Check test校核试验Chief draftsman 主任制图员Chromium 铬Chromizing 镀铬处理Circle 圆、圆周Circle of reference 参考圆Addendum circle 齿顶圆Base circle 基圆Graduated circle 分度圆Imaginary circle 虚圆Outside circle 齿顶圆、外圆Pitch circle 节圆Rack circle 平面齿轮、扇形齿轮Root circle 根圆Top circle齿顶圆Circular cylinder 圆柱Circular pitch 弧线节距Circular thickness 弧线(齿)厚度Circumference 圆周长Clamp 夹紧、夹板Class 种类Class of fit 配合级别Classification 分类Claw 爪、钩、卡爪Clearance fit 间隙配合Clevice /clevis U形钩、U形夹Clevis bolt 套环(插销)螺栓Clevis pin U形夹销Clockwise 顺时针方向Clutch 离合器、联轴器Coat 外层、涂镀层Coat of metal 金属镀层First coat 底漆Coating 镀、覆盖Electrodeposited coating 电镀层Coaxial circle 共轴圆Cock 旋塞Coil 蛇形管、螺管、线圈Coil spring 盘簧Coincident line 重叠线Cold-rolled steel 冷轧钢Collet 夹头Collet chuck 弹簧夹头Color-harden 着色硬化、发蓝、煮黑Common difference 公差Company 公司Joint company 股份公司Limited company 有限公司Compass 圆规Compass of proportion 比例规Component 零件、构件Compression spring 压力弹簧Compressor 压缩机Computer 计算机Concave face 凹面Concentricity 同心度Cone 圆锥Cones development 锥面展开Cone pulley 锥形轮、塔轮Conical spring 锥形弹簧Connection 联接Bolt-on connection 螺栓联接Flange connection 法兰联接Rivet connection 铆钉联接Screw connection 螺钉联接Contact 接触、接合、啮合Contact angle 啮合角Angular contact ball bearing 向心止推球轴承Contour 外形、轮廓线Contracted drawing 缩图Contrast 对比、对照、比较Convention 惯例、常规、习惯Convention for materials 材料的习惯表示法Conventional break 习惯断裂画法Conventional diagram 习惯画法Conventional intersection 习惯交线(画法) Conventional practice 习惯画法Conventional sign 图例、习惯符号|Convex 凸面Conveyer 输送机、传送机Cooler 冷冻机Coordinate axis 坐标轴Coordinate paper 方格纸、坐标纸Copper 铜Copy 抄本、样板Correction 校正、修正Cotter pin 开口销Split cotter 开口销Counterbore 埋头孔、锥口孔Counterclockwise 逆时针方向Countersink 埋头孔、沉孔Countersink drill 中心钻、钻Countersunk 钻埋头孔、钻锥口孔Countersunk bolt 埋头螺钉Countersunk head 埋头Countersunk hole 锥坑Coupling 联轴节Cover 盖、罩Cylinder cover 汽缸盖Dust cover 防尘罩Cowl 壳、套、盖Crane 起重机Crank 曲柄、曲轴Crankshaft 曲轴Crest 峰、尖、牙尖Cross head 十字头Cross section 横剖面、横断面Crown gear 冕状齿轮Cube 立方形体、正六面体Current 电流Curvature 曲率Curvature radius 曲率半径Curve 弯曲、曲线、曲线板Curve plotter 绘图仪Curve ruler 曲线板French curve 曲线板Moment curve 力矩曲线、力矩图Cutter 刀、刀具Cutting plane 截平面Cutting plane symbols 剖切(迹线)平面符号Cycloid 摆线Cycloidal gear 摆线齿轮Cylinder 圆柱体Cylinder base 汽缸座Pump cylinder 泵缸Cylindrical cam 圆柱凸轮Cylindrical fit 圆柱配合Cylindrical roller bearing 圆柱滚子轴承Dash 短划线、虚线、破折号Dash and dot line 点划线Broken dash 断裂线Data 数据、资料Engineering data工程数据Master data 主要数据Date 日期、年代Datum 基准(点、线、面)、资料Datum line 基准线Datum point 基准点Datum plane 基准面Decade 十进制、十进位Decelerator 减速器、制动器、缓动装置Decimal 小数的、十进位小数的Decimal fraction 十进制分数Decimal fraction system 十进小数制Decimal scale 十进位比例尺Decimeter 分米、公分Dedendum angle 齿根角Dedendum circle 齿根圆Definition 定义Deformation 变形、扭曲Degree 度、程度Degree of accuracy 精度Degree of freedom 自由度Degree of hardness 硬度Degree scale 刻度Circular degree 圆度Delineation 轮廓、草图Delineator 制图者Department 科、处、系、车间Draft department 设计科Engineering department 技术科Fitting department 装配车间Heat treatment department 热处理车间Mechanical department 机加工车间Processing department 工艺科Depth 深度、高度Depth dial gauge 深度千分表Depth of engagement 啮合深度Depth of thread 螺纹深度Depth of tooth 齿高Contact depth of tooth 啮合高度Working depth of tooth 齿工作高度Derivation 偏差Standard derivation 标准偏差Description 描述、作图、绘制Design 设计、计划Design activity 设计机关(组织) Design assembly 设计装配图Design drawing 设计图Design layout 设计草图、初步设计图Preliminary design 初步设计Standard design 标准设计Technical design 技术设计Designation 符号、标志Designation strip 铭牌Designer 设计员、制图者、设计师Desk 桌、控制台Drawing desk 绘图桌Detail 细目、细节、详图、零件Detail drawing 详图、零件工作图Detail paper底图纸、描图纸Detail specification 详细规格Detent 棘爪、扳手、制动器Developable surface 可展曲面Developed view 展开图Development inner port 内表面展开图Development of surface 表面展开图Deviation 偏差、偏移Angular deviation 角偏差Average deviation 平均偏差Standard deviation 标准偏差Tolerance deviation 允许偏差Device 装置、设备Diagram 示意图、图解Diagram drawing 图解图、结构图Arrangement diagram 布置图Assembly diagram 装配示意图Block diagram 方框图Schematic diagram 原理图、简图Diagrammatic drawing 草图、示意图Dial gauge 千分表Dial inside micrometer 内径千分表Diameter 直径Diameter of aperture 孔径Diameter of pitch circle 节圆直径Diameter pitch (齿轮)径节Diameter run-out径向跳动Major diameter 大直径、螺纹外径Minor diameter 小直径、螺纹内径Nominal diameter 公称直径Pitch diameter of screw thread 螺纹中径Thread diameter 螺纹外径(直径) Diametral pitch 齿轮径节Die 模具、扳牙Diesel 柴油机、内燃机Dimension 尺寸Dimension line 尺寸线Limiting dimension 极限尺寸Nominal dimension 公称尺寸Outer dimension 外形尺寸、轮廓尺寸Direction 方位、方向Clockwise direction 顺时针方向Disc = disk 圆盘、原板Disk cam 圆盘凸轮Dismount 拆卸Dismountable 可拆卸的Displacement 移位、变位Distance 距离、路程Distortion 变形、歪扭Distribution 分配、分布、配置Ditto machine 复印机Diversion 变更、转换Dividing head 分规Dot line 虚线Dotted line 虚线Double dots line 双点划线Double helical pinion 人字小齿轮Double helical spur gear 人字齿轮Double thread 双头螺柱Dowel thread 定位销、圆柱销Dozer 推土机Draft = draught (拔模)斜度、草图、制图Drafting 制图Drafting board 制图板Drafting machine 制图机Drafting tape 制图带、胶带Draftsman 绘图员Drawer 制图员Drawing 绘图、图样Drawing board 绘图纸Drawing control 图样管理Drawing free-head 草图Drawing instrument 绘图仪器Drawing number 图号Drawing pencil 绘图铅笔Drawing pin 图钉Drawing size 图纸尺寸Drawing table 制图桌Drawing with compass 用圆规画图Blue print drawing 蓝图Free hand drawing 徒手图Full size drawing 原大图Skeleton drawing 草图、结构图Working drawing 施工图、制造图、工作图Drill 钻孔、穿孔、穿孔器Drive 传动、驱动Drive fit 打入配合Air drive 气动Belt drive 带传动Chain drive 链传动Friction drive 摩擦传动Gear drive 齿轮传动Hydromatic drive 液压传动Speed-reducer drive 减速器传动Variable-speed drive 变速传动Worm-wheel drive 蜗轮传动Driven gear 从动齿轮Driven shaft 从动轴Driving gear 主动齿轮Driving shaft 主动轴Drum cam 凸轮轴Ductile iron 球墨铸铁Duplicating tracing 复制描图Durometer (钢轨)硬度计Dusting cloth 抹灰布、撒粉布Eccentricity 偏心距Edge iron 角铁Edge round 外圆角Edge view 边视图Effective diameter 有效直径Effective face width 有效齿宽Efficiency 效率、性能Mechanical efficiency 机械效率Elastic deformation 弹性变形Elasticity 弹性Elbow 肘形弯管、弯头Electric current 电流Electric element 电池Elephant 绘图纸(28X23英寸) Elevation 正面图、立视图End 末端、头Ball end 秋端Butt end 平端、端面Tail end 尾端Top end 顶端Engagement 啮合Engineer 工程技术人员、工程师Engineer-in-chief 总工程师Equipment 设备Eraser 橡皮Erasing shield 擦图片Erection diagram 安装图、装配图Error 误差Accumulated error 累积误差Allowance error 容许误差Average error 平均误差Permissible error 容许误差Relative error 相对误差Exterior 外表面External 外部External diameter 外径External dimension 外形尺寸External fillet 外圆角External thread 外螺纹Extra fine(screw)特细牙螺纹Eyelet = eyelet-hole 小孔Fabrication 建造、制造Face 面、正面、表面、端面Face cam 平面凸轮Face gear 平面齿轮Face hardening 表面硬化Inner face 里面Outer face 外面Face off 倒角Factor of safety 安全系数Factory 工厂、制造厂Factory made 工厂制造的Fastener 接合件、紧固件Fastening 连接件、紧固件Fatigue 疲劳Faucet 旋塞、龙头、开关Feather 滑键、冒口Feather key 滑键Feature 特征、特性、性能Basic mechanical design feature 主要机械设计性能Mechanical feature 机械性能(特性)Feed-pump 供油泵、供水泵Feet 英尺Ferrous metal 黑色金属Field 工场、现场Figure 形状、图样、插图、数字File 锉刀、锉平Filler 填料、垫片Fillet (内)圆角、填角、嵌条Fillet radius 内圆角半径Filter 过滤器Fine thread series 细螺纹级(系列)Finish 完工、加工、磨光Finish all over 全部加工Finish marks 加工符号Machine finish 机器光制Fit 配合Clearance fit 间隙配合Free fit 自由配合Interference fit 静配合Light press fit 轻压配合Light running fit 轻传动配合Loose fit 松配合Normal-running fit 传动配合Running fit 动配合Shrink fit 冷缩配合Slide fit 滑动配合Transition fit 过渡配合Fix 安装、装配、调整、修理、固定Flange 法兰盘、凸缘Flank 边、侧面、齿侧、后面Flat 扁头、平面Flat key 平键Flat spring 板弹簧Flat surface 平面Flexible disk coupling 挠性盘形联轴节Flexible gear-type coupling 挠性齿轮联轴节Flywheel 飞轮Foot 英尺Foot screw 地脚螺钉Force 力Fore word 序、前言Forge 锻Forge steel 锻钢Former 样板、模型、量规Wooden former 木模Formula 公式Foundation 基础、基座Foundation bolt 地脚螺栓Foundry 铸件、铸工车间Fraction 分数、小数Front view 前视图、主视图Full diameter 大直径、主直径Full line 实线Full size 原大Full scale 原大Full section 全剖视Full section view 全剖视图Furbish 研磨、擦光Fuse 保险丝、熔断器Gage = gauge 量规Gallon 加仑Galvanize 镀锌、电镀Gasket 垫圈、密封垫Gasket material 填料Gasoline engine 汽油(内燃)机Gate 门、阀门Gear 齿轮Gear addendum angle 齿顶角Gear box(case) 齿轮箱Gear centre 齿轮中心Gear dedendum angle 齿根角(圆锥齿轮) Epicyclic gear 行星齿轮Herringbone gear 人字齿轮Ratchet gear 棘轮General drawing 总图Geometry 几何学Gland 压盖、填料盖、密封装置Glass 玻璃Glasscloth 砂布、玻璃布Glossary 词汇(表)Grade 等级、斜度Steel grade 钢号Graduated hardening 分级淬火Graduated scale 比例尺、分度尺Gram 克Graph 图(表、解、形)、曲线图Graph paper 方格纸Graphic图示、制图学Grease 滑脂Grind 磨削、抛光Grinding machine 磨床Grinding wheel 砂轮Groove cam 槽凸轮Groove pulley 槽轮、三角带轮Guide 手册、指南Guide bar 导杆Guide pin 定位销、导向销Guide screw 丝杠Guidebook 参考手册、指南、入门Half 二分之一、一部分Half bearing 轴瓦Half section 半剖视Half section view 半剖视图Hammer 锤子Handbook 手册、指南Hand-made 手工制造的Hand-operated 手控的Handle 手柄Hand wheel 手轮Hard casting 白口铁Hard drawn 冷拔Hard rolled 冷轧的Hard surfacing 表面硬化Harden 淬火、硬化Hardened and tempered 调质的Hardened-steel 淬火钢Hardening 硬化Hardness 硬度Hardometer 硬度计Hatch 剖面线H-beam 工字梁、H形梁Heat–treatment 热处理Heavy force fit 重压配合Height 高度Helical bevel gear 螺旋伞齿轮Helical gear 螺旋齿轮、圆柱斜齿轮Helical rack 斜齿齿条Helical spring 螺旋弹簧Hex nut 六角螺母Hexagon jam nut 六角锁紧螺母Hexagon socket head 内六角头Hidden line 虚线Hidden outline 看不见的轮廓线High-carbon steel 高碳钢High-duty 重型的、大型的、优产的High-speed steel 高速钢Hosting jack 千斤顶Hole 孔Horizontal datum plane 水平基准面Horizontal line 水平线Horizontal projection 水平投影Horizontal projection plane 水平投影面Horse-power 马力、功率Hose 软管Hose coupling 软管接头Hot-rolled steel 热轧钢Hot-work 热加工Hour 小时Housing 机座Housing of pump 泵体Bearing housing 轴承箱Gear housing 齿轮箱Hub 轮、中心、衬套I-beam 工字钢Illustration 插图、实例Inaccuracy 不精确、不准确Incenter 内(切圆)心Inch 英寸Incline 斜度、斜面Index plate 分度盘Indicator 指示计、百分表Industrial 工业公司Industrial drawing 工业制图Industry 工业Inertia 惯性Ink 墨水、油墨Ink holder 钢笔杆China ink 墨汁Inscription 标题Inside diameter 内径Inspection 检修、检查Inspection machine 检修机器Inspector 检查员Installation 装置、设备、安装Installation diagram 安装图Institute 研究所、协会、学院、学会Instruction 说明、指示Instrument 仪器、仪表、工具Instrument drawing 仪器图Intensity 强度Interchangeability 互换性1 Interconnection 互相连接Interference fit 静配合Interior view 内部(的)视图Internal combustion engine 内燃机Internal fillet 内圆角Internal gear 内齿轮Introduction 引言、介绍、序言Invisible line 虚线Involute 渐(伸)开线Involute gear 渐开线齿轮Involute rack 渐开线齿条Involute spline 渐开线花键Involute teeth 渐开线齿形Iron 铁Ingot iron 低碳铁、工业纯铁Knobbled iron 熟铁Magnetic iron 磁铁Malleable iron 可锻铁、韧性铁Plate iron 铁板、钢板Quadrant iron 方钢Rod iron 圆铁、棒钢Round iron 圆铁、圆钢Rustless iron 不锈铁Section iron 型钢Structural iron 结构钢White iron 白口铁Wrought iron 熟铁、锻铁Isometric diagram 等轴测图Isometric drawing 等轴测图Jack-screw 螺旋千斤顶Job sheet 零件图纸Joint 结合、连接、焊接Bolt joint 螺栓连接Riveted joint 铆钉连接Welded joint 焊接Journal 轴径Journal bearing 径向轴承Keeper 保持器(片)、架、定位件卡箍Keep-ring 保持环Key diagram 键、按钮Key way(seat、seating、slot)键槽Key wrench 套筒扳手Gib-head taper key 钩头斜键Square key 方形键Tightening key 斜扁键Woodruff key 半圆键Key-bolt 键螺栓Kilogram(me)公斤、千克Kilogram-meter 公斤米、千克米Kilometer 公里、千米Kilovolt 千瓦Kilowatt 千伏Kit 一套工具Knee 弯头、升降台Knee bend 弯管Knob 捏手、按钮Knuckle thread 圆形螺纹Knurl 滚花、压花Knurled nut滚花螺母L-bar = L-beam 角钢Laboratory 实验室、研究室Lamp 灯Alarm lamp 信号灯Daylight lamp 日光灯Incandescent lamp 白炽灯Indicating lamp 信号灯、指示灯Lantern 游环、套环Large compasses 大圆规Lathe 车床Lathe-hand 车工Lattin = Latten 金属薄板、黄铜片Law 规律、定律Lay 布置、安排、放置Layer 层Carburized layer 渗碳层Layout 计划、方案、草图Layout design 草图设计、方案设计Layout drawing 方案草图Lead angle 螺旋升角Lead line 指引线Leaf spring 板弹簧Left hand 左方向Left hand thread 左旋螺纹Legend 图例、图表符号、代号、说明书Length 长度、距离Length gauge 长度规Length of normal 法线长Length of side 边长Effective length 有效长度Lens 透镜、镜片Letter 字、字母Capital letter 大写字母Level surface 水平面Lift 升降机、电梯Light alloy 轻合金Light beam 光束Light series 轻系列Light-duty 轻型Lighting installation 照明装置Lightning switch 照明开关Liquid 液体Limit 极限尺寸Limit switch 限位开关Line 线Line of action (齿轮)压力线Line of contact (齿轮)接触线Line of shaft轴线Line of thickness 线型的粗度Line weight线的粗细程度Actual line实线Addendum line齿顶线Broken line断裂线Center line = central line中心线Continuous line实线Dash(ed) line虚线Diagonal line 对角线Imaginary line 假想线Generation line 母线Pitch line 节线Real line 实线Reference line 基准线、参考线Right line 直线Skeleton line 轮廓线Solid line 实线Straight line 直线Vertical line 垂直线Liner 衬套Bearing line 轴瓦Link 连接环、链节Line assembly 连杆装配图Chain link 链节L-iron 角铁List 注册、记录、名册、目录Load 符合Actual load 有效载荷、实际载荷Allowable load 容许载荷Full load 满载(荷)、全负载(荷) Local view 局部视图Localization 定位\固定Locating pin 定位销Location by angle 角度定位Location by dimension 定位尺寸Location pin 定位销Location tolerance 定位公差Lock 锁\阀Lock nut 防松螺母Lock screw 锁紧螺钉Lock washer 弹簧垫圈Valve lock 阀簧抵座销、气门制销Loco 机车、火车头Logarithm 对数Long break 长断裂线Long radius 长半径Longitudinal key 长方键Lower limit 下限Lubricant pump 润滑油泵Lubricating ring 润滑油环Lubrication 润滑Bath lubrication 油浴润滑Bearing lubrication 轴承润滑Ring lubrication 油环润滑Shot lubrication 油枪润滑Splash lubrication 飞溅润滑Lubricator 润滑器Lubro-pump 油泵Luminaire 光源Machine 机器、切割Machine building (manufacturing) 机械制造Machine drawing 机械制图Machine finish 机械加工Machine maker 机械工厂(制造者) Machine part 机械零件Machine shop 机工车间Drawing machine 绘图机Tracing machine 描图机Machining allowance 加工余量Machinist 机械工人\机械师Magazine 杂志Magnetic-particle clutch 电磁离合器Magnitude 数量、长度、大小Major type of slotted nut 大型锁母Make 制造、构造Malleable cast iron 可锻铸铁Malleable casting 韧铸件Malleable steel 软钢、展性钢Manual 手册、说明书Manual control 手控Manufacture 加工、制造业Manucturing engineering 制造工艺(技术) Manucturing machine 生产机械Manucturing tolerance 制造公差Master check 校正、校对Master drawing 样图Master gauge 标准规、校准规Master gear 主齿轮、标准齿轮Master making 手工Master screw 标准螺纹Match 匹配、配合Mate 啮合部分Material 物质、材料Fibre material 纤维材料Insulating material 绝缘材料Plastic material 塑料Maximal valve 极大值Maximum 极点、极限、最大量Maximum admitted diameter of work 工件最大许可直径Mean axis 中间轴Measure 量度、大小、尺寸Measure of precision 精确度Measurement 测定、尺寸、大小Measuring device 量具Measuring tools 量具Mechanical bolt 螺钉Mechanical drawing 机械制图Mechanical engineering’s scale 机械工程比例尺Mechanical properties 机械性能Mechanical reduction gear 齿轮减速装置Mechanism 机械结构、机械装置Medium series 中系列Mating member 配合件Meshing gear 啮合齿轮Metal 金属Admiralty metal 含锡黄铜Bell metal 青铜合金、种铜、铜锡合金Brazing metal 铜锌合金Hard metal 硬质合金Heavy metal 重金属Light metal 轻金属Monel metal 铜镍合金Power(ed) metal 粉末合金Wear-resistant metal 耐磨金属White metal 白合金(铅锑锡合金)Yellow metal 黄金、黄色金属Metallized 镀金属的、喷涂金属的Meter 米、公尺。
装施图纸常见缩写表-中英文对照
装施图纸常见缩写表-中英文对照装施图纸常见缩写表-中英文对照 I图纸缩写表AR- Architecture Information Plan 建筑信息图EM- Electrical Mechanical Plan 机电设备图FC- Floor Covering Plan 地坪布置图FF- Fixture/Furning Plan 家具布置图RC- Reflected Ceiling Plan 天顶布置图EL- Elevation 立面图 DT- Detail 节点详图WF- Wall Finish Plan 墙身饰面图IL- Interior Landscaping Plan 室内景观设计图MR- Mockup Room 样板房IR- Interior Rendering 室内效果图PA- Public Area 公共区域空间缩写表客房空间ST-Standard Twin 标准双人房SK-Superior King 标准大床房SS-Superior Suite 标准套房HS-Hospitality Suite 标准残疾人套房DS-Deluxe Suite 豪华套房PS-Presidential Suite 总统套房ES-Executive Suite 行政套房EDS-Executive Deluxe Suite 行政豪华套房餐饮空间PDR-Privant （private ） Dinning Room 包厢 VIP-Very Important Person 贵宾SR-Specialty Restaurant 风味餐厅JC-Japanese Cooking 日本料理KC-Korean Cooking 韩国料理Chinese Restaurant 中餐厅Lobby Lounge 大堂吧Bar 酒吧Coffee Shop 咖啡厅Tea House 茶馆Ball Hall 宴会厅All-day Dinning 全日制餐厅Canteen 员工餐厅Pantry 备餐厅公共空间Concierge 礼宾Entrance 入口Reception Exterior 下客区（雨棚）Lobby 大堂Service Station 服务台Foyer 过厅Elevator Hall 电梯厅Rest Room 卫生间Corridor 走廊Cloister 回廊Lounge 休息厅Billiard 台球室GYM 健身室商务办公空间Business Center 商务中心第 1 页Meeting Room 会议室Multi-function Room 多功能厅商业空间Travel Agency 旅行社Book Store 书店Boutique Store 精品店（专卖店）Flower Shop 花店Retail 零售店办公空间Manager Room 经理办公室室内设计中英对照词汇翻译 Iblow-upart work by othersection planTV feature TVwall detailsselected artworktimber conpartment12mm thk tempered glass top finish 12mmpolished cu bronze table leg timber skirtingstudy desktimber backingsocket outletsingle switch socket outlet AFFLFFLpaint finishwall coveringmild steel L-angle support plan sectiondoor pullwallcoveringpivot hinge up to load 200kg up toelevationelevation @ corridorshower door hingesglass door sealdoor panelheavy-dutytrackvanitydoor framedoor closer concealenddoor viewershaftcorridordoor codeQTY=quantitylocationkitchendescriptioncloser 放大图艺术品有其他单位负责剖面图局部（TV 放大图）墙部细节（墙体大样）艺术品选定（艺术品自购）木格（隔断）厚钢化玻璃台面磨光铜桌脚木踢脚线书桌木材背衬（木衬板）电器插座（outlet 出口通风）单开关插座天花完成面地面完成面涂料完成面墙体完成面（壁纸）软钢L 角支撑（L 型软角钢支撑）平面大样门拉手墙面涂料（壁纸）枢轴合页，可负载200kg 胜任，直达立面图走廊立面图淋浴门合页（铰链状）玻璃门封条（封缝条，缓冲条）门板重型的，耐用的导轨梳妆台（小型卫生间）门框隐蔽式闭门器门镜管井，烟道走廊门编号数量，大量地点厨房描述闭门器第 2 页lockset 锁具stopper 软木塞（缓冲条，密封）hinge 铰链push 推，挤，按pull 拉，拨kick plate 刮板door bottom 门铃item 项目，条款，一条，一则brand 商标，牌子model size 型号尺寸cat no. cat=category 种类，类别refer to specification bookironmongery schedulefoyerstone floorebonished （matt ） timbercard key locking systemplan viewstone walldoor handledoor jambdoor buffervelvet surface wropfood/snackschampagne bottlekettle by othersice bucket12mm thick clear glass panel 12mm coated aluminium A/C air supply grille to match wallcoveringretractable timber bunds8mm thk mirror 8mmstone deckbath tubstone vanityremoveable timber shelvingbronze inlaylevel 8 guestroom plan 8scale 1:100hotelfor presention 03/28/1958keyplanstandaro king roomfurnishfixture & furnishing plan图）project NO. 3333sheet NO. 3333drawnapprovedrevisiondouble double bed roomconnection king roomsuitedesign consultants 参照规范用书五金店详单（报表）门厅石材地面亚光面人造黑檀木门卡系统平面图，俯视图石材墙门拉手（门侧柱）门顶缓冲器天鹅绒表面包装食物/零食香槟酒瓶水壶由其他单位负责冰桶厚清玻板备有饰面的铝制空调送风栏配合墙壁饰面（配合墙面的铝制空调格栅）可拉回的木帘（木制百叶帘）厚镜子石材层面浴缸梳妆台石材可移动的木饰面架板（放毛巾）嵌入式铜板层客房平面图比例1:100酒店提交于***索引平面图标准大床客房布置，陈列 vt固定，陈设平面图，家具布置图（平面布置工程号3333表格号3333制图批准修改，修订双人客房（双人双床客房）连接双人客房套房设计顾问第 3 页hirsch/bedner and associates HBAexecutive suite 行政套房internet station 上网站lounge area 休息室reception 接待处restroom 卫生间reading area 阅读区dining area 用餐区buffet counter 自助吧台 pantry area 配餐厅VIP entry foyer VIP 入口前厅bathroom 浴室，卫生间safe 保险箱luggage 行李bedroom 卧室living room 客厅mini bar 迷你吧台powder room 化妆室panty 配菜，备菜wine display 酒品展示区bar counter 柜台study room 研究室master bedroom 主人房master bahroom 主卫jacuzzi 按摩浴缸room matrix 房间矩阵图（索引，概述）individual plan 独立平面图（分类平面图）typical 典型的bathtub 浴缸presidential suite plan 总统套房平面图executive lounge plan 高级休息区平面图royal suite plan 高贵套房平面图satin bronze frame 缎子铜框（数量+观点+形状+国籍+材料绸子一样的青铜框） upholstered seat 软席upholstered panel fin 布饰面板（布面块软包）concealed light by lighting consultant 隐藏灯饰由照明顾问负责timber finish 木材饰面室内设计中英对照词汇翻译 IIetched glass finish 蚀刻玻璃完成面（绣蚀玻璃）headboard 床头板exhaust 排气timber sliding door 木饰面推拉门ceiling 天花concealed track 隐藏导轨（百叶）onyx veneer pendant 悬挂的玛瑙饰面（pendant 悬挂的，吊下的。
工程图纸中英文对照表
三:線材類相關詞匯(CABLE) 編織 隔离 地線 棉線 銅箔絲 青銅 導體數 封膠 編織倒反 貼紙 四:加工 銅箔360度環焊 包鋁箔 包銅箔 附固定螺母 絕緣厚度 完成外徑 發泡PP塑膠膜 黑色成型 鐵粉芯成型 非移料耐 五:包裝 PE袋 膠紙封袋 POLYBAG 散裝 TAPE SEALED BULK 熱封口 迷你帶 MIN TIE HEAT SEALED 吊卡 HANGING CA COPPER FOLL SHIELDED WITH 360 LOLD 正面 反面 TO PSIDE RE VERWR SID BOTH CONNECTORS MUST HAVE AN AVUMINUM FOLL WTHUMB SCREW NUT INSULATION THICKNESS OUERALL DIAMETER FOAM PP TAPE BLACK MOLDED FERRITE COREMOLD ABS NON MIGROLION 電線結構 絕緣阻抗 電壓設定 脫皮鍍錫 固定螺母 BRAID SHIELD SPIKAC CHIELD DUAIN(PW) COTTON YARN TINSHL BRONZE CONDUCTORS NO TWIXT PAIR LABEL 單隔离 鍍錫銅 銅包鋼 搓麻 外被 填充 線徑 絞向 鐵粉芯 SINGLE SHIELD TINNED COPPER CLAD COPPER SPLRAL OUTER JACKET FILLER DIMETER DIRECTION RCA絕緣電木 FRT 黃銅 導體材質 平均厚度 棉紗 BRASS MATERIAL AVENAGE THUCKNR COTTON 絞距 裸銅 漆包線 TWIST PNCTT BARE COPPER COARTYPE) 紅色 粉紅 棕色 灰色 銀色 黃色 淡 二:插頭類相關詞匯 鍍鎳 鍍錫 鍍鋅 鉚合 交流 直流 焊接式 MCKEL PLATEL TIN PLATEL ZINC PLATED CRIMP AC DC SOLDET TYPE 連接頭 接觸PIN 導體 熱縮套管 環 端子 公頭 CONNECTOR CONTACT CONDUCTOR HEAT SHRINK TUBE RING TERMINAL MALE 鍍銀 彈片 絕緣 螺絲 鍍金 沖壓式 母頭 SILVER PLATED SPRING LATCH INSULATION SCREWS GOLD FLASH CRIMP TYPE FEMALE RED PLNK BROWN GRAY SILVER YELLOW LIGHT 藍色 綠色 橙色 象牙色 巧克力色 透明色 重 BLUE GREEN ORANGE IVORY CHOCOLATE TRANSPARENT DARK 黑色 白色 紫色 棕印色 貝色 金色 BLACK WHITE PURPLE BROWN BLACK BEIGE GOLD MAT
图纸尺寸英文模板
图纸尺寸英文模板篇一：工程图纸英语工程图纸英语Material 材料Notes/Remark 注释ANSI 美国国家标准局ASTM美国材料试验协会finish 最后一道表面处理Anodize 阳极氧化Grain 纹理standard标准Range 范围UNLESS OTHERWISE SPECIFIED除非另有标明外，请参照备注Tolerances 公差punching direction 冲压方向Right Side 正面TH（thickness)料厚Hardness 硬度Burring side 批锋面Tooling/Die 冲压模JIS 日本工业标准Covex 米位.surface cleaning 金属表面清洁处理Degreasing 金属除油处理Solvent degreasing 乳化脱脂alkali degreasing 碱性脱脂electrolytic cleaning 电解清洁vapor degreasing 蒸汽脱脂ultrasonic cleaning 超声波清洁vibrating cleaning 震动清洁barrel cleaning 滚桶清洁brushing 刷光polishing 磨光buffing 抛光electro-polishing 电解抛光。
3. process term(工序术语）The bending processes 屈弯工序bending 屈弯curling 卷曲Twisting 扭曲flanging 翻外边The cutting processes 剪切工序piecing 冲孔blanking 冲裁notching 剪形lancing 切口trimming 切边fine blanking 精冲the forming processs 成型工序embossing 起伏起形（冲波位）rim curling 边口卷曲hole flanging 翻猪嘴孔成型bulging expanding 胀颈成形reducing necking 缩颈成形foring pression 锻压成形the multiple-slides forming operations 多滑块式成形the drawing process 压延工序cupping (blank&draw)冲裁及压延redrawings 再压延partial redrawing 局部压延reverse drawing 反压延ironing 挤延Scale 比例Decimal 小数的usage 用量length 长度section A-A 剖面图A-ADETAIL B 放大图 BView 视图tension 张力，拉力torque 扭距力strength 力量dimension 尺寸first angle projection 第一视角法third angle projection 第三视角法REV.版本Edge 边corner 角top 顶部bottom角部MIN.最小screw 螺纹appearance 外观outline 轮廓，外形approx,大约datum 基准plane 平面measurement of parallelism 平行度测量verticality 垂直度lineal measure 直线度测量flatness 平面度roughness 粗糙度ECO/ECN 工程变更通知finish/treatment 表面处理anodizing of aluminum 铝的阳极处理。
机械图纸中常用词汇英语缩写图文稿
机械图纸中常用词汇英语缩写图文稿预览说明:预览图片所展示的格式为文档的源格式展示,下载源文件没有水印,内容可编辑和复制机械图纸中常用词汇英语缩写集团文件版本号：（M928-T898-M248-WU2669-I2896-DQ586-M1988）机械图纸英语翻译以下是我在工作中常用的ALL WELDS CONTINUOUS UNLESS OTHERWISE STATED. 未注焊缝均为连续焊ALL WELDS 3mm FILLET UNLESS OTHERWISE STATED 未注焊角高3mm.ALL UNSPECIFIED RADI - R3 未注圆角R3REMOVE ALL BURRS AND SHARP EDGES 棱角倒钝 CHANNEL 槽钢RSA 708 角钢 70X70X8M30X1.5 pitch M30X1.5的锥螺纹Tackweld 点焊 OD 1/4" outside dimension 1/4"的缩写外径直1/4"75 CRS 尺寸为75 材质为冷轧钢板410 OPENING REF 410 开口参考尺寸40 REF 尺寸为40,参考值2.5" BSP 2.5” 圆锥管螺纹2.5" BSPT HEXAGON2.5” 六角圆锥管螺纹(即对丝) 30x2.5 FLAT BAR 30X2.5 扁钢TYP 2 POSNS 2处 11 TOTAL COILS APROX.9 WORKING COILS APROX.RIGHT HAND WOUND ONLY,END COILS SQUARE TO TOUCH. 总圈数约11圈；工作圈数约9圈；右旋；弹簧的端部磨平以便于接触.(此为弹簧技术说明) FEMALE: 内扣(母扣) MALE: 外扣(公扣) 偏心轴 eccentric shaft销轴 PIN开口销 COTTER PIN螺杆 screw紧定螺钉 SET SCREW圆螺母 ROUND NUT内六角螺钉 SOCKET HEAD CAP SCREW六角螺钉 HEX HD SETSCREW六角螺栓 HEX HD BOLT挡圈 closing ring弹性挡圈 circlip轴承隔套 distance sleeve of axletree轴承 axletree深沟球轴承 DEEP GROOVE BALL BEARING无扣长 non-buckle longth弹簧 SPRING吊环螺钉 LIFTING EYE BOLT开槽盘头螺钉SLOTTED PAN HEAD SCREW 圆锥滚子轴承TAPERED ROLLER BEARING推力球轴承THRUST BALL BEARING 平键 FLAT KEY弹簧垫圈 SINGLE COIL SPRING WASHER平垫圈 FLAT WASHER螺母 FULL NYLOCK NUT圆螺母 ROUND NUTREMOVE ALL BURRS AND SHARP EDGES 所有尖角/棱角倒角并去毛刺40 REF 为测量的参考尺寸OD 1/4’ outside dimension 1/4"的缩写外径直1/4’------->应该为：外径值1/4"75 CRS 尺75 材质为冷轧钢板 ------->应该为：尺寸75 材质为冷轧钢板我见过18GA(.048")CRS、16GA(.060)CRS、14GA(.075)CRS，其中GA是表示厚度的，但与英寸的关系还没研究明白；照此推算75是相当薄的缩写全称翻译ACCESS Accessory 附件ADJ Adjustable,Adjust 调整ADPT Adapter 使适应ADV Advance 提前AL Aluminum 铝ALLOW Allowance 允许ALT Alternate 改变ALY Alloy 合金AMT Amout 数量ANL Anneal 锻炼ANSL Amer Natl Stds Institute APPROX Approximate 大约ASME Amer Society of MechEngrsASSEM Assemble 装配ASSY Assembly 装配AUTH Authorized 授权的AUTO Automatic 自动的AUX Auxiliary 辅助的AVG Average 平均AWG American Wire Gauge BC Bolt Circle 螺栓圆周BET Between 之间BEV Bevel 斜角BHN Brinell Hardness Number 布氏硬度值BLK Blank ,Block 空白B/NM Bill of Material 材料费BOT Bottom 底部BP or B/P Blueprint 蓝图BRG Bearing 轴承BRK Break 破裂BRKT Bracket 支架BRO Broach 钻孔BRS Brass 黄铜BRZ Bronze 青铜B＆S Brown＆Shape 棕色＆形状BSC Basic 基本的BUSH Bushing 套管BWG Birmingham Wire GaugeC TO C Center-to-Center 中心到中心CAD Computer-Aided Drafting 电脑辅助设计CAM Computer-Aided Mfg CAP Capacity 容量CAP SCR Cap Screw 螺帽CARB Carburize 使渗碳CBORE Counterbore 扩孔CCW Counter Clockwise 逆时针CDRILL CounerdrillCDS Cold-Drawn Steel缩写全称翻译EFF Effective 有效的ENCL Enclose,Enclosure 附上ENG Engine 引擎ENGR Engineer 工程师ENGRG Engineering 工程学EQLSP Equally Spaced 等距EQUIV Equivalent 相等EST Estimate 估计EX Extra 额外EXH Exhaust 消耗EXP Experimental 实验性的EXT Exension,External 范围,外部FAB Fabricate 伪造FAO Finish All OverFDRY Foundry 铸造FIG Figure 数据FIL Fillet,fillister 带子FIM Full Indicator Movement FIN Finish FLX Fixture 结构FLX Floor.Fluid,Flush 基地,液体,冲洗FLEX Flexible 易弯曲的FLG Flange 边缘FORG Forging 锻炼FR Frame,Front 边框FIG Fitting 装置FURN Furnish 提供FWD Forward 向前GA Gage,Gauge 测量GALV Galvanized 电镀GR Grade 等级GRD Grind 磨碎GRV Groove 凹槽GSKT Gasket 垫圈H＆G Harden and Grind 加硬和磨碎HD Head 主要的HDL Handle 处理HDLS Headless 无领导的HDN Harden 使硬化HDW Hardware 硬件HEX Hexagon 六边形HGR Hanger 衣架HGT Height 高度HOR Horizontal 水平的HRS Hot-Rolled SteelHSG Housing 外罩HT TR Heat Treal我见过18GA(.048")CRS、16GA(.060)CRS、14GA(.075)CRS，其中GA是表示厚度的，但与英寸的关系还没研究明白；照此推算75是相当薄的缩写全称翻译ACCESS Accessory 附件ADJ Adjustable,Adjust 调整ADPT Adapter 使适应ADV Advance 提前AL Aluminum 铝ALLOW Allowance 允许ALT Alternate 改变ALY Alloy 合金AMT Amout 数量ANL Anneal 锻炼ANSL Amer Natl Stds Institute APPROX Approximate 大约ASME Amer Society of MechEngrsASSEM Assemble 装配ASSY Assembly 装配AUTH Authorized 授权的AUTO Automatic 自动的AUX Auxiliary 辅助的AVG Average 平均AWG American Wire Gauge BC Bolt Circle 螺栓圆周BET Between 之间BEV Bevel 斜角BHN Brinell Hardness Number 布氏硬度值BLK Blank ,Block 空白B/NM Bill of Material 材料费BOT Bottom 底部BP or B/P Blueprint 蓝图BRG Bearing 轴承BRK Break 破裂BRKT Bracket 支架BRO Broach 钻孔BRS Brass 黄铜BRZ Bronze 青铜B＆S Brown＆Shape 棕色＆形状BSC Basic 基本的BUSH Bushing 套管BWG Birmingham Wire Gauge C TO C Center-to-Center 中心到中心CAD Computer-Aided Drafting 电脑辅助设计CAM Computer-Aided Mfg CAP Capacity 容量CAP SCR Cap Screw 螺帽CARB Carburize 使渗碳CBORE Counterbore 扩孔CCW Counter Clockwise 逆时针CDRILL CounerdrillCDS Cold-Drawn Steel缩写全称翻译EFF Effective 有效的ENCL Enclose,Enclosure 附上ENG Engine 引擎ENGR Engineer 工程师ENGRG Engineering 工程学EQLSP Equally Spaced 等距EQUIV Equivalent 相等EST Estimate 估计EX Extra 额外EXH Exhaust 消耗EXP Experimental 实验性的EXT Exension,External 范围,外部FAB Fabricate 伪造FAO Finish All OverFDRY Foundry 铸造FIG Figure 数据FIL Fillet,fillister 带子FIM Full Indicator Movement FIN Finish FLX Fixture 结构FLX Floor.Fluid,Flush 基地,液体,冲洗FLEX Flexible 易弯曲的FLG Flange 边缘FORG Forging 锻炼FR Frame,Front 边框FIG Fitting 装置FURN Furnish 提供FWD Forward 向前GA Gage,Gauge 测量GALV Galvanized 电镀GR Grade 等级GRD Grind 磨碎GRV Groove 凹槽GSKT Gasket 垫圈H＆G Harden and Grind 加硬和磨碎HD Head 主要的HDL Handle 处理HDLS Headless 无领导的HDN Harden 使硬化HDW Hardware 硬件HEX Hexagon 六边形HGR Hanger 衣架HGT Height 高度HOR Horizontal 水平的HRS Hot-Rolled SteelHSG Housing 外罩HT TR Heat Treal缩写全称翻译NTS Not to ScaleOA Over All 所有OBS ObsotetcOC On CenterOD Outside Diameter 外直径OPP Opposite 对立OPTL Optional 可选择的OR Outside Radius 外半径ORIG Original 初始的PAT. Patent 专利PATT Pattern 形式PC Piece,Pitch Circle 件，节距圆PCH Punch 打孔PD Pitch DiameterPERF Perforate 打孔PERM Permanent 永久的PERP Perpendicular 垂直的PFD Preferred 首选的PKG Package,Packing 包装PL Parting Line,Places,Plate PNEU PncumaticPNL Panel 面板POL Polish 磨光POS Position,Postive 位置PR Pair 对立PRI Primary 基本的PROC Process 程序PROD Product,Production 产品，产量PSI Pounds per Square Inch PT Part,Point 零件，点QTR Quarter 四份之一QTY Quantity 数量QUAL Quality 质量R Radius 半径RA Rockwell Harden,A-Scale RB Rockwell Harden,B-Scale RC Rockwell Harden,C-Scale RECD Received 巳收到的RECT Rectangle 长方形REF Reference 相关的REINF Reinforce 增强REL Release,Relief 释放，缓解REM Remove 移除REQD Requird 有需要REE Retainer,ReturnREVReverse,Revision,Revolution RFS Regardless of Feature Size RGH Rough 粗糙的RH Right Hand 右手RIV Rivet 起皱RM Ream 扩展RND Round 周围RPM Revolutions per Minute RPW Resistance Projection WeldSAE Society of Automotive EngrsSCH Schedule 进度表CFS Cold-Finished Steel CH Case HardenCHAM Chamfer 斜面CHAN Channel 渠道CHG Change 改变CHK Check 核查CI Cast Iron 铸铁CIR Circle, Circular 圆周CIRC Circumference 圆周CL Centerline 中心线CLP Clamp 夹子CNC Computer Numerical Control 电脑数值控制COMB Combination 联合COML Commercial 商业的CONC Concentric 同中心的CONN Connect,Connector 连接器COV Cover 盖子 CPLG Coupling 联结 CQ Commercial Quality 商业等级钢CRS Cold Stds Association CRT Cathode Ray Tube 阴级射线管CS Cast Steel 铸铁CSA Canadian Stds Association CSK Countersink 埋头孔 CSTG Casting 铸件 CTR Center 中心 CU Cubic 立方米 CW Clockwise 顺时针 CYL Cylinder,Cylindrical 柱面DBL Double 双倍 DEC Decimal 小数 DEG Degree 摄氏度 DET Detail 详情DEV Develop 发展DFT Draft 草稿DIA Diameter 直径DIM Dimension 尺寸 DIST Distance 距离 DN Down 向下DP Deep,Diametral Pitch 深度,径节DR Drill,Drill Rod 钻孔 DSGN Design 设计DVTL Dovetail 吻合DWG Drawing 图纸DWL Dowel 木钉DWN Drawn 拔出 EA Each 每个 ECC Eccentric 古怪缩写全称翻译 HVY Heavy 重量 HYD Hydraulic 水压ID Inside Diameter 内部直径 IDENT Identification 鉴定ILLUS Illustration 说明IN Inch 英寸INCL Include,Including 包括INCR Increase 增加INFO Information 信息INSP Inspect 检查INSTL Install 安装INST Instruct,Instrument 指示,工具INTInterior,Internal,Intersect 内部的,内在的,交叉IR Inside Radius 内部半径ISO Internal Stds Organization 国际标准化组织JCT Junction 连结JNT Journal 杂志JT Joint 连接K Key 关键KNRL Knurl 硬节KST KeyseatKWY Keyway 键沟LB Pound 英镑LBL Label 标签LG Length,Long 长度LH Left Hand 左手LMC Least Material Condition LOC Locate 位于LT Light 光LTR Letter 信LUB Lubricate 润滑MACH Machine 机器MAINT Maintenance 维护MATL Material 材料MAX Maximum 最大MECH Mechanical,Mechanism 机械MED Medium 媒介MFG Manufacturing 制造业MI Malleable Iron 可锻造的铁MIN Minimum, Minute 最小，秒MISC Miscellaneous 混杂的MM Millimeter 毫米MMC Max Material ConditionMS Machine SteelMTG Mouting 装备MULT Multiple 倍数MWG Music Wire GagugNA Not Applicable 不可应用的NATL National 国内的NC Numerical Control 数字电脑控制NEG Negative 忽略的NO. Number 号码NOM Nominal 名义上的NPSM Natl Pipe Straight Mech NPT Natl Pipe Tapered 缩写全称翻译SCR Screw 螺丝SEC Second 秒SECT Section 部分SEP Separate 独立SEQ Sequence 顺序SER Serial,Series 系列SERR Serrate 锯齿状SF SpotfaceSFT Shaft 轴SGL Single 单个SH Sheet 纸SI Intl System of Units SL Slide 使滑动SLV Sleeve 袖子SOC Socket 插座SP Space,Spaced,Spare 空间SPL Special 特别SPEC Specification 规格SPG Spring 跳SPHER Spherical 球体SPRKT Sprocket 链轮齿SQ Square 平方SST Stainless Steel 纯铁STD Standard 标准STK Stock 存货STL Steel 铁STR Straight,Strip 直的SUB Substitute 替代物SUP Supply,Support 供应SURF Surface 表面SYM Symmetrical 对称的SYS System 系统T Teeth,T ooth 牙齿TECH Technical 技术TEMP Template,Temporary 模板，暂时的THD Thread 线THK Thick 厚的TOL Tolerance 公差TOT Total 总计TPF Taper per FootTPI Taper per In,Threads per InchTPR Taper 锥形TS Tool SteelTYP Typical 典型UNC Unified Natl Coarse UNEF Unified Natl Extra Fine UNF Unified Natl FineUNIV Universal 普遍VAR Variable 变量VERT Vertical 垂直的VOL Volume 音量VS Versus 与．．相对W Wide,Width 宽度WASH Washer 洗衣机WDF Woodruff 车叶草WI Wrought Iron 熟铁WT Weight 重量齿轮及齿轮加工中英文对照-A部分A.1. abrasive tooth wear 齿面研磨磨损2. absolute tangential velocity 绝对切向速度3. accelerometer 加速表4. addendum 齿顶高5. addendum angle 齿顶角6. addendum circle 齿顶圆7. addendum surface 上齿面8. adhesive wear 粘着磨损9. adjustability 可调性10. adjustability coefficients 可调系数11. adjusting wedge 圆盘端铣刀的可调型楔块12. allowable stress 允许应力13. alternate blade cutter 双面刀盘14. angular backlash 角侧隙15. angular bevel gears 斜交锥齿轮16. angular displacement 角移位17. angular pitch 齿端距18. angular testing machine 可调角度试验机19. approach action 啮入20. arbor 心轴21. arbor distance 心轴距22. arc of approach 啮入弧23. arc of recess 啮出弧24. attraction 收紧25. average cutter diameter 平均刀尖直径26. axial displacement 轴向位移27. axial factor 轴向系数28. axial locating surface 轴向定位面29. axial pitch 轴向齿距30. axial plane 轴向平面31. axial rakeangle 轴向前角32. axial thrust 轴向推力33. axle testing machine 传动桥试验机第4楼Piping work: 铺管工程Steam trace:加热蒸汽管道Cutting:切割socket weld承插焊接fillet weld角焊,填角焊branch connection分支接续fabrication tolerance .制造容差local heat treatment 局部热处理threaded pipe螺纹管seal welding密封焊接flange joint凸缘接头undercut底切feeder馈电线conduit outlet电线引出口seal fitting密封接头, 密封配件Screw thread lubricant 螺纹润滑剂Seal绝缘层weld reinforcement焊缝补强lock washer锁紧[止动, 防松]垫圈electrical panel配电板,配电盘nipple螺纹接头zinc plated镀锌的ring joint环接, 围缘接合bolt螺栓control控制器National Electrical Code 全国电气规程master schedule主要图表, 综合图表, 设计任务书, 主要作业表torque wrench转矩扳手job site施工现场flange connection凸缘联接Hard hat安全帽Goggles护目镜Stockpile贮存packing list装箱单crate柳条箱purchased material list原材料进货单back-feed反馈wire coil线盘线卷NPT thread美国标准锥管螺纹cable gland电缆衬垫terminal block线弧, 接头排接线盒, 接线板, 线夹power drill机械钻connector接线器insulated sleeve绝缘套管wire connector接线器wire terminal电线接头control wiring控制线路motor lead电动机引出线power wiring电力布线tender document提供证件orifice plate挡板nut螺母flange gasket法兰垫片dimensional inspection 尺寸检验burn through烧蚀piping system管道系统reinforcement of weld 加强焊缝械专业词汇表"机械(常用)" "abrasion, abrasive wear","磨料磨损""active force, applied force","作用力""actual size","实际尺寸" "addendum angle","齿顶角" "addendum","齿顶高" "addendum modification","径向变位""addendum modification (for external gears)","径向变位量" "addendum modification coefficient","径向变位系数" "additive ","添加剂" "adhesion wear","黏着磨损" "adjusted rating life","修正额定寿命""aerodynamic bearing","气体静压滑动轴承""air spring","空气弹簧" "angle drive","角度传动" "angle of contact","包角"。
英文图纸单词释义
英文图纸中的单词释义wall bracket 墙托座wall brick 墙砖wall cabinet 嵌墙绸wall chase 墙槽wall column 墙柱wall component 墙装配件wall crane 墙上起重机wall facing 墙饰面wall footing 墙基脚wall form 墙模板wall handrail 墙上扶手wall heatiing panel 散热墙板wall hung water closet 墙挂式自洗便器wall in trench 壕沟墙wall iron 墙上管夹wall line 墙外围线wall luminaire 壁照描备wall mounted heater 壁装式加热器wall opening 墙洞wall panel 护墙板wall paper 墙纸wall plate 承梁板wall pointing machine 墙勾缝机wall run 暂时的墙洞wall skin 地下室墙防水wall string 墙楼梯斜梁wall tie 系墙铁wall tile 墙面贴砖wall urinal 墙挂式小便器wall wash lumunaire 筑入墙的照眠wallboard 墙板waller’s hammer 石垛工锤walling 墙wallpapering work 贴墙纸warm air curtain 热风幕warm air duct 热空气管warm air heating 热风供暖warm air heating unit 热风供暖装置warm water method 温水法warning system 警报系统warp 翘曲warren girder 瓦伦大梁warren truss 瓦伦大梁wash 洗wash basin 洗脸盆wash fountain 公用洗涤池wash house 餐具洗涤室wash primer 洗涤底漆wash water trough 洗涤排水沟washing and screening plant 洗选装置washing screen 洗矿筛washing screw 螺旋洗涤机waste disposal unit 废物处理装置waste heat 废热waste heat utilization 废热利用waste heating 废热供暖wasted energy 损失的能量watch room 警卫室water 水water air heating system 水气供热系统water basin 硫water bearing ground 含水地层water boiler 热水锅炉water booster system 加压装置water borne dumper 砾石倾卸船water boundary 水界water cement 水硬水泥water cement ratio 水灰比water circulation 水循环water closet 抽水马桶water conservation 水源保护water consumption 水消耗water contained in aggregates 骨料的自然湿度water cured concrete 水熟混凝土water curing 水养护water demand rate 水消耗定额water filled roof 充水屋顶water filled steel framed structure 充水钢框架结构water filter 滤水器water filtration plant 水过滤场water fittings 给排水管配件water front construction 沿岸建筑物water gallery 排水坑道water glass 水玻璃water glass color 硅酸盐颜料water glass paint 水玻璃颜料water hardness 水硬度water heater 水加热器water holding capacity 含水能力water jet pump 喷射泵water jetting 水冲法water level 水位water main 给水干管water management 用水管理water meter 量水器water monitoring 水监测water of hydration 结合水water paint 水性漆water pipe 给水管water post 给水站water power dam 水电站坝water pressure 水压water protection zone 水源保护区域water putty 防水油灰water reducing admixture 减水外加剂water reducing agent 减水剂water repellent facing 防水饰面water resistance 耐水性water resistance paint 耐水漆water retaining admixture 保持水外加剂water retaining capacity 保水能力water retaining structure 挡水建筑物water retentive portland cement 保水性波特兰水泥water service 给水water service pipe 给水管water softening plant 软水设备water storage tank 贮水箱water strainer 滤水器water supply 给水water supply engineering 给水工程water supply facilities 给水设备water supply fittings 给水管零件water supply network 给水管网water supply reservoir 给水用贮水池water supply scheme 给水系统water supply system 给水系统water tight concrete 防水混凝土water to water heater 水水加热器water to water system 水水系统water treatment plant 净水厂water treatment works 净水厂water tube boiler 水管式锅炉water vapor 水汽water works 自来水厂water works engineering 给水工程water/binder ratio 水灰比waterfall 瀑布waterline network 给水管网waterlogged soils 浸饱水的土壤waterproof agent 防水剂waterproof canvas 防水帆布waterproof cement 防水水泥waterproof concrete 防水混凝土waterproof construction 防水构造物waterproof mortar 防水灰浆waterproof paint 防水漆waterproof plaster 防水抹灰waterproofing 防水waterproofing admixture 防水外加剂waterproofing compound 防水化合物waterproofing course 防水层waterproofing emulsion 防水乳剂waterproofing felt 防水毛毡waterproofing materials 防水材料waterproofing work 防水处理waterrepellent cement 援性水泥waterrepellent concrete 援性混凝土waterrepelling admixture 援外加剂watersphere 球状水压式贮水器watertight core 防渗心墙waterway 水路watery city 水上城市wave 波wave erosion 波蚀wave force 波力wave generator 波形信号发生器wave impact 波浪冲击wave load 波浪荷载wave pressure 波浪压力wavy line 波形线wax 蜡wax emulsion 蜡乳化液way 道wc and bathroom unit 厕所浴室设备单元wc flushing cistern 冲洗水箱wc pan 抽水马桶wc suite 厕所套间weak concrete 低标号混凝土wear 磨耗；磨耗wearing course 磨耗层wearing layer 磨耗层weather 天气weather boarding 安装风雨板weather groove 泻水槽weather resistance 抗风化weather resistant concrete 抗风化混凝土weathering 风化web 腹板web member 腹杆web plate 腹板web splice 腹板搭接web stiffener 腹板加劲件wedge 楔wedge anchor 楔锚固装置wedge anchorage 插楔wedge of failure 楔形滑坍wedge valve 楔形阀wedging 楔固weigh batch plant 重量配料设备weigh batching 按重量配料weigh box 计量箱weigh hopper 秤料斗weighing apparatus 秤weighing batchbox 重量配料器weighing batcher 重量计量器weight 重量weight ratio 重量比weighted cement 重水泥weir 堰weld 焊weld crete 混凝土粘结剂weld decay 焊缝腐烂welded construction 焊接结构welded reinforcement 焊接钢筋welded steel structure 焊接钢结构welded wire fabric 焊接钢筋网welding 焊接welding arc 焊弧welding goggles 焊工护目镜welding helmet 焊工面罩weldment 焊件well 井well burned brick 烧透砖well cementing 钻孔灌浆well foundation 井筒基础well interference 井间干扰wet concrete 塑性混凝土wet consistency 塑性稠度wet construction 湿式施工wet mix shotcrete 湿拌喷射水泥灰浆wet mortar 湿灰浆wet screed 抹灰刮板wet screening 湿筛wettest stable consistency 塑性混凝土稳定稠度wetting agent 润湿剂wharf 码头wheel 轮whetstone 磨石white brick 白砖white cement 白水泥white lead 铅白white portland cement 白色硅酸盐水泥whitewash 石灰水whole brick wall 一砖墙wibdow fastener 窗闩销wide flange beam 宽翼缘梁wimble 手摇钻winch 绞盘wind 风wind bracing 抗风支撑wind deflection 风力偏移wind effect 风力影响wind girder 风障梁wind load 风荷载wind pressure 风压wind pressure coefficient 风力系数wind protection screen 防风板wind speed alarm 风速警报器wind uplift 风浮力wind vibration 风振windbreak 防风林winder 斜踏步winding 线圈winding machine 缠绕机window 窗window air conditioner 窗式空调window back 窗腰window band 带形窗window bar 窗闩window board 窗舌板window box garden 窗台花坛window butt 窗铰链window catch 窗钩window fittings 窗配件window frame 窗框window glass 窗玻璃window guards 窗铁栅window hangings 窗帘window head 窗框上槛window lintel 窗过梁window mullion 窗框的中框window opening 窗口window panel 带窗口板件window pier 窗间壁window reveal 窗帮window schedule 窗一览表window sill 窗盘window space 窗户玻璃面积window unit 窗单元window wall 玻璃墙windowless building 无窗房屋windward side 迎风面wing 耳房wing pile 翼状桩winter 冬季winter building construction 建筑物冬季施工winter building techiniques 冬季施工法winter concreting 冬季浇筑混凝土winter garden 冬景花园winterized concrete plant 冬季制造混凝土工厂wire 金属线wire anchorage 铁丝锚固wire brushing 钢丝刷清理wire cable 钢索钢丝绳wire cloth 金属丝布wire construction 钢酸构wire dam 石框坝wire fabric 铁丝网wire fence 铁丝栅栏wire glass 夹丝玻璃wire lath 金属网wire mesh reinforced concrete 钢丝网配筋混凝土wire reinforced concrete 钢丝配筋混凝土wire rope 钢丝绳wire rope sling 钢丝绳吊索wire tie 铁丝系材wiree gauze 铁丝网wireless tower 天线塔wiring 配线wiring diagram 配线图withe 烟囱隔板wobble coefficient 摆动系数wood 木wood block 木块wood brick 木砖wood cement concrete 木屑混凝土wood chipboard 碎木板wood chisel 木凿wood construction 木结构wood fiber 木纤维wood fiber board 木纤维板wood fiber concrete 木丝混凝土wood fiber slab 木纤维板wood fibered insulation 木纤维绝热wood fibered plaster 木纤维灰浆wood float 木抹子wood flooring 木地板wood flour 木屑wood frame construction 木框架结构wood frame house 木框架房屋wood laminated arch 木制叠层拱wood lath 木板条wood panel construction 木板结构wood screw 木螺钉wood stave pipe 木条拼成的水管wood structure 木结构wood wool 木丝wood wool cement slab 木丝水泥平板wood wool concrete 木丝混凝土wood wool slab 木丝平板wooden apartment 木质公寓wooden barrack 木质工棚wooden construction 木结构wooden door 木门wooden form 木模板wooden furniture 木制家具wooden shingle 木板瓦wooden turned baluster 精制木质栏杆小柱wooden weir 木堰woodwork 木制品woodworker’s vise 木工虎钳woodworking industry 木制品工业woodworking machinery 木工机械wool 羊毛work as executed drawing 实测图work cubes 混凝土方体work in progress 过程进行中的工作work level 工捉台work progress 施工过程workability 可加工性workability admixture 增塑外加剂workable concrete 有和易性混凝土workable weather 做活适合天气worker 工人working 椎working area 工住地working chamber 工滓working crew 椎队working deck 工专working design 施工设计working drawing 工准working load 使用负载working load limit 极限工咨载working place 工住所working plan 工灼划working platform 工专working platform of a scaffold 脚手架工捉台working pressure 工坠力working range 工锥围working stress 工爪力working stress design 许用应力设计法working width 工醉度working zone 工坐域workmanship 工资量workmen’s shelter 工人临时生活设施works 结构物works beam test 就地梁试验works cube strength 实际小方块强度workshop 工厂；修理厂wrench 扳钳x ray analysis x射线分析x ray examination x射线检查x ray intensity monitor x光强度检验x ray shielding concrete x线屏蔽混凝土x ray test x射线检查xunderground plant 地下工厂xylograph 木板画xylolite 菱苦土木屑板y branch y 形支管y junction y形接头yard 庭院yard drainage 庭院排水yard gulley 庭院排水沟year round air conditioning 全年式空气第yellow 黄色yellow ocher 羝yield 屈服yield point 怜点yield range 屈服区域yield strength 屈服强度yield stress 屈服应力yielding 屈服yielding ground 松软土地yielding support 可缩性支座yoke 轭状物young’s modulus of elasticity 杨氏模量youth center 青年厅堂zenith 顶点zero end of survey 路线测量的起点桩zero line 零位线zero moment 零力矩zero moment method 零力矩法zero slump concrete 坍落度为零的混凝土zinc 锌zinc white 锌白zonal ventilation 区域通风zone 带zoning 分地带zoning plan 分区规划zoo 动物园zoological garden 动物园zoological park 动物园u bend u 型管u stirrup u 形箍筋ultimate bearing capacity 极限承载量ultimate bending moment 极限弯矩ultimate compressive strength 极限抗压强度ultimate design 极限设计ultimate design resisting moment 极限设计抗力矩ultimate factor of safety 极限安全系数ultimate limit state 极限状态ultimate load 极限荷载ultimate load analysis 极限荷载设计ultimate load design 极限荷载设计ultimate loading 极限加荷重ultimate moment 临界矩ultimate resistance 极限强度ultimate shear stress 极限剪应力ultimate shrinkage 极限收缩量ultimate strength 极限强度ultimate strength method 破坏强度设计法ultimate stress 极限应力ultimate tensile strength 极限抗拉应力ultra high strength concrete 超高强度混凝土ultrasonic pulse velocity method 超声脉冲速度法ultrasonic sounding 超声波测深测ultrasound 超声波ultraviolet rays 紫外线umbrella roof 伞形屋顶unbalanced load 不平衡负载unbalanced moment 不平衡力矩unbonded member 未粘结后张预应力构件unbonded post tensioning 无束缚后加拉力unbonded tendon 未粘合的预应力钢筋unbuilt area 未建区unburnt brick 未烧透砖uncased pile 无壳套桩unconfined groundwater 非承压地下水uncontrolled ventilation 无控制通风uncoursed rubble masonry 乱砌毛石under river tunnel 河底隧道underbed 底架underbrush 小试undercoat 底漆undercrossing 下穿交叉underdrainage 地下排水underfloor duct 地板下管道underfloor heating 地板下供暖underfloor heating cable 地板下供暖电缆underflow 地下水流underground 地下underground car park 地下停车站underground concrete 地下混凝土underground construction 地下工程underground garage 地下车库underground palace 地下官殿underground pipeline 地下管道underground railway 地下铁道underground run off 排水暗沟underground shelter 地下防空洞underground structures 地下构造物underground tank 地下储罐underground water 地下水underground water head 地下水水头underlayer 垫层underpinning 加固基础undersanded concrete 少砂混凝土混合料underwater concrete 水下混凝土underwater concreting 水下灌注混凝土underwater structures 水下结构undistorted ground 原壮土undisturbed sample 原状土试样undisturbed soil 原壮土undreground works 地下构造物undressed timber 未刨光木料unframed door 无骨架门扇unglazed tile 滞光瓷砖ungrading 筛分析unhardened concrete 未硬结混凝土uniform beam 等截面粱uniform grading 均匀粒径uniform load 均匀荷载uniform settlement 均匀沉陷uniform stress 均布应力uniformity 均匀性uniformly distributed load 均布载荷union 管接头union flange 管接法兰unique construction 特种结构unit 单位unit air conditioner 单位空气第机unit air heater 空气加热机组unit area 单位面积unit construction 构件组合unit cooler 单位冷却机组unit cost 单价unit deformation 单位变形unit generalized load 广义单位荷载unit heater 热风机unit lateral strain 单位横向应变unit load 单位荷载unit of area 面积单位unit pressure 单位压力unit producing yard 部件预制场unit strain 单位应变unit volume expansion 单位体积膨胀unloaded chord 不载荷弦unprotected metal construction 无保护层金属构造unrammed spread concrete 未夯实混凝土unreactive aggregate 惰性集料unreinforced concrete 无钢筋混凝土unrestrained member 无约束部件unset concrete 未凝结混凝土unsound aggregate 劣质骨料unsound cement 不坚固水泥unsound plaster 劣质不安定灰泥unstability 不稳定性unstable ground 不稳定地面unstable soil 不安定土壤unsteamed concrete 非蒸养混凝土unstiffened member 未加劲构件unsymmetrical beam 不对称梁unsymmetrical bending 不对称弯曲untensioned reinforcement 无受力钢筋unusual structure 异常结构unworkable concrete 难灌筑混凝土建筑 build; architecture; construct; architectural; architectural & industrial ceramics 建筑安装工程量 construction work quantity建筑板材 building board建筑材料表 list of building materials建筑材料检验 building material testing建筑材料行 building material dealer建筑材料运输列车 construction train建筑草图 architectural sketch建筑朝向 building orientation建筑成本预算 construction cost estimate建筑承包商 building contractor建筑尺度 architectural scale建筑处理 architectural treatment建筑创作 architectural creation建筑大五金 architectural metalwork建筑大样 architectural detail建筑单元 building unit建筑费 construction cost建筑风格 architectural style建筑辅助系统 building subsystem建筑钢 construction(al) steel建筑钢板 building sheet建筑高度 building height; height of building建筑高度分区 building height zoning; height zoning建筑工程升降机builder’s lift建筑工地选择 siting建筑工羊角锤头builder’s claw hammer head建筑工业 building industry; construction industry建筑工种 building trades建筑构思 architectural conception建筑构图 compostion on architecture; architectural composition 建筑构造 building construction建筑估价 building cost estimate建筑管理 architectural control建筑规程 building regulations建筑规范 building code建筑机械 construction machinery; building machinery建筑及维护规则 recommendation建筑结构 building structure建筑结构分析语言 structural engineering system solver (STRESS) 建筑立面 elevation of building; building elevation建筑沥青 bitumen for building; building asphalt No. 10建筑力学 architectural mechanics建筑铝型材生产线 architectural aluminium profile production line 建筑毛面积 gross floor area建筑毛造价 gross building cost建筑面积 area of structure; covered area建筑面积比 floor-area ratio (F.A.R.)建筑面积指标 floor-space index (F.S.I.)建筑模数 building module建筑配景 entourage of building建筑平面 architectural plane; building plane建筑起重机 building crane; construction-site crane建筑砌块 building block建筑气候分区 climate region of building建筑青铜 architectural bronze建筑青铜合金 architectural bronze建筑声学 architectural acoustics建筑石 paring stone建筑石料 building stone建筑时期观念 construction period concept建筑史 architectural history; history of architecture建筑收进线 building setback line建筑陶板 architectural terra-cotta (ATC)建筑陶瓷 architectural pottery建筑特色 architectural feature建筑体积 architectural volume; cubage建筑体积计算 cubing建筑体系 building system建筑体形 building size建筑透视 architectural perspective建筑外壳 building shell建筑外形 architectural appearance建筑物 building; structure建筑物保险 building insurance建筑物朝向 direction of building建筑物基础 building foundation建筑物间距 distance between buildings建筑物理 architectural physics; building physics建筑物缺隐 building deficiency建筑物入口 building entrance建筑物租约 building lease建筑现场 construction建筑限制 building restriction建筑限制线 building restiction line建筑效果 architectural effect建筑型钢轧机机座 structural stand建筑型式 type of construction; architectural form建筑遗产 architectural heritage建筑艺术 architectural art建筑艺术处理 artistic treatment in architecture; architectural treatment建筑艺术形式 artistic form of architecture建筑用地 building lot; building site; lot建筑用地规划 plot planning; block planning建筑用钢铁 constructional iron建筑用黄铜 architectural brass建筑用木材 building timber建筑用提升机 service-building elevator建筑原理 architectonics; architectural principle建筑造型艺术 art of architectural modelling建筑占地系数 coefficient of land used for buildings建筑障碍 architectural barriers建筑照明 architectural lighting建筑折旧准备 buildings depreciation reserve建筑哲理 architectural philosophy建筑柱式 architectural orders; orders of architecture建筑装饰 architectural decoration; architectural ornament建筑装饰彩釉砂涂料 colour-glazed sand paint for building decoration 建筑装饰学 architectural decoration建筑装修五金 architectural metalwork建筑自动化 building automation建筑自重 structural weight per square meter建筑渲染 architectural rendering; renduup feed heating system 上给下分式供暖系统up ligthing 向上照明up to date technics 现代化的技术upkeep cost 维持费uplift pressure 浮力upper chord 上弦杆upper layer 上层upper reinforcement 上部钢筋upper yield point 上屈服点upright 立柱upright course 竖立砌层upstanding beams slab 上肋形板urban area 城市地区urban art 城市美术urban center 市中心区urban communications 城市交通urban community 城市居住区urban conservation 市区保存urban construction 城市工程urban decoration 市区装饰urban development 城市发展urban dwelling 市区住宅urban environment 城市环境urban form 城市形式urban freeway 城市高速道路urban growth 市区扩展urban hygiene 市区卫生urban morphology 城市形态urban park 市区公园urban patteren 城市形式urban planning 城镇规划urban renewal 市区改建urban sprawl 城市扩展urbanist 城市规划者urinal 小便器usable floor area 可用地板面积use 使用use district 特殊建设区域useful capacity 有效容量useful cross section 有效截面useful load 有效荷载usefull space 有效空间utensil sink 厨房用洗涤盆utilities 城市管理服务行业utility core 公用事业中心utility gas 日用煤气utility shaft 工程设施网用竖井utility structures 公用事业建筑utilization 利用v beam sheeting v 形截面钢护墙板v brick v 形砖v joint v 形缝vacancy area 空地vacuum 真空vacuum concrete 真空混凝土vacuum core 真空采样器vacuum dewatering plant 真空脱水装置vacuum filter 真空过滤机vacuum filtration 真空过滤vacuum form 真空模板vacuum heating system 真空加热系统vacuum lifting equipment 真空提升设备vacuum mat 真空吸垫vacuum method wellpoint 真空预压法井点vacuum mold 真空模板vacuum pad 真空垫vacuum treated concrete 真空处理混凝土valley 谷valley breeze 谷风valley gutter 斜沟槽valley jack 屋顶斜构处撑杆valley rafter 屋顶斜构处椽valley roof 带斜沟屋顶value 值valve 阀valve bag 自封袋vanishing point 灭点vapor 汽vapor lock 汽封vaporization 蒸发vapour 汽variable air volume system 可变空气量系统variable concentrated load 可变集中荷载variable furniture 可变家具variation 变化varnish 清漆varnish brush 清漆刷varnish color 清漆涂料varnish paint 清漆涂料varying load 变动负荷vault 穹窿vault abatment 穹窿支座vault bay 拱顶跨度vault construction 拱顶结构vault rib 穹窿拱肋vault thrust 穹窿推力vaulting tile 穹形中空陶瓷块vav system 可变空气量系统vebe apparatus 贝氏振动式稠度计vector 失量vee gutter v形排水槽vehicle 运输工具；媒液velocity 速度veneer 胶合板veneer partition 镶板间壁veneer tie 镶面板系材veneered construction 贴面结构veneered door 镶胶合板veneered plywood 饰面胶合板veneered wall 镶面墙vent sash 楣窗vent shaft 通风井vented form 有通气孔模板ventilating duct 通风管道ventilating pipe 通气管ventilating shaft 通风井ventilating skylight 通风天窗ventilation 换气ventilation brick 通风砖ventilation cavity 通风穴ventilation heat loss 通风热损失ventilation installation 通风装置ventilation load 换气负荷ventilation opening 通风口ventilation plant room 通风装置室ventilation rate 换气次数ventilation system 通风系统ventilator 送风机ventlight 楣窗veranda 阳台verdurization 绿化verge board 挡风板verge cutter 边缘切割机verge fillet 檐口瓦嵌条vermex concrete 隔声混凝土vermiculite aggregate 蛭石骨料vermiculite concrete 蛭石混凝土vermiculite mortar 蛭石灰浆vertex 顶点vertical alignment 竖向定线vertical bar 竖杆vertical displacement 垂直位移vertical links 垂直连杆vertical meeting rail 窗扇盖缝条vertical pivoting window 竖轴转窗vertical plan 垂直面图vertical sash 竖拉窗vertical shoring 托换基础vertical sliding window 竖拉窗vertical strip door 垂直条幅木板门vertical ties 垂直系材vertical tiling 竖墙贴砖vertical web member 垂直桁材very light aggregate concrete 特殊轻质骨料混凝土very light concrete 特殊轻质混凝土vessel 容器vest pocket park 小型公园vestibule 门厅vets housing 老手住宅viaduct 高架桥vibrated concrete 振实混凝土vibrating beam 震捣梁vibrating chute 抖动式滑槽vibrating circular pipe line circular 振动输送管vibrating conveyor 振动式输送机vibrating float 振动抹子vibrating grizzly 振动筛vibrating mold 振动模vibrating pebble mill 振动砾磨机vibrating plate 振动板vibrating roller 振动辊vibrating screed 震捣梁vibrating screen 振动筛vibrating stressing bed 振动张拉台座vibrating table 振动台vibrating tamper 振动压实机vibration 振动vibration control 振动控制vibration isolation 振动控制vibration limit 振动限度vibrator 振动器vibrator cylinder 圆筒振捣器vibratory bullfloat 振动抹子vibratory compactor 振动压实机vibratory pile hammer 振动打桩机vibratory spiral elevator 振动螺旋升降机vibro driver 振动打桩机vibrofinisher 振动轧平机vibrofloat machine 振浮压实器vibroflotation soil compaction 振浮压实土壤vibrolithic concrete 分割浇注混凝土vibromill 振动磨vibromold 振动模vibropile 振动灌注桩vibropiling 振动打桩vibroplatform 振动台vibroroller 振动滚轧vibrorolling 振动压延vibrosieve 振动筛vibrotrunk 振动滑槽vice 虎钳vierendeel girder 带上下桁条的梁view 情景villa 别墅village 乡村vinyl asbestostiles 石棉尸铺板vinyl tiles 乙烯基板viscoelastic strain 粘弹性变形viscometer 粘度计viscosity 粘度viscosity factor 粘度系数visibility 能见度visibility factor 视度系数vision 视界visionproof glass 毛玻璃vista 远景visual concrete 外露混凝土vitrified brick 玻璃砖void 空隙void cement ratio 隙灰比void filler 填隙料void formers 制孔机void pockets 气窝voids 空隙voids content 孔隙含量voids ratio 空穴系数voids volume 孔隙体积volcano 火山volt 伏特voltage 电压voltmeter 电压电量计volume 容积volume batcher 按体积比配料器volume batching 按体积比配合volume expansion 体积膨胀volume ratio 容积比volumetric analysis 容积分析volumetric batch plant 容积计量设备volumetric batcher 按体积比配料器volumetric change 体积变化vortex 涡旋vortex air supply panel 旋涡空气分配板vortex reactor 涡动反应器vortex tube 涡淋voussoir 拱楔块voussoir arch 楔形块拱wa ce cretor 水灰计量装置waffle slab 格子板wages 工资wagner fineness 瓦格纳细度wagon 货车wagon ceiling 拱形顶棚wainscot 护壁镶板waisted specimen 缩腰的试件waiting room 等待室walk up building 无电梯的公寓walked on roof covering 有步行道的屋顶walks 搭板walkway 跳板wall 墙wall absorption 墙吸水wall air conditioner 墙挂式空碟wall anchor 墙锚wall base 墙座wall beam 墙托梁wall bearing construction 墙承重的结构wall bed 壁床建筑英语词汇to build, to construct 建设，建筑，修建architecture 建筑学building 修筑，建筑物house 房子skyscraper摩天大楼block of flats 公寓楼（美作：apartment block）monument 纪念碑palace 宫殿temple 庙宇basilica 皇宫，教堂cathedral 大教堂church教堂tower 塔，塔楼ten-storey office block 十层办公大楼column 柱colonnade 柱列arch 拱town planning 市政（美作：city planning）building permission 营建许可证，建筑开工许可证greenbelt 绿地elevation 建筑物的三面图plan 设计图scale 比例尺to prefabricate 预制excavation挖土，掘土foundations 基to lay the foundations打地基course of bricks 砌好的砖列scaffold脚手架scaffolding脚手架这里有一些景观方面的词汇1.主入口大门/岗亭(车行 & 人行) MAIN ENTRANCE GATE/GUARD HOUSE (FOR VEHICLE& PEDESTRIAN )2.次入口/岗亭(车行 & 人行 ) 2ND ENTRANCE GATE/GUARD HOUSE (FOR VEHICLE& PEDESTRIAN )3.商业中心入口 ENTRANCE TO SHOPPING CTR.4.水景 WATER FEATURE5.小型露天剧场 MINI AMPHI-THEATRE6.迎宾景观-1 WELCOMING FEATURE-17.观景木台 TIMBER DECK (VIEWING)8.竹园 BAMBOO GARDEN9.漫步广场 WALKWAY PLAZA10.露天咖啡廊 OUT DOOR CAFE11.巨大迎宾水景-2 GRAND WELCOMING FEATURE-212.木桥 TIMBER BRIDGE13.石景、水瀑、洞穴、观景台ROCK’SCAPE WATERFALL’S GROTTO/ VIEWING TERRACE14.吊桥 HANGING BRIDGE15.休憩台地(低处) LOUNGING TERRACE (LOWER )16.休憩台地(高处) LOUNGING TERRACE (UPPER )17.特色踏步 FEATURE STEPPING STONE18.野趣小溪 RIVER WILD19.儿童乐园CHILDREN’S PLAYGROUND20.旱冰道 SLIDE21.羽毛球场 BADMINTON COURT22.旱景 DRY LANDSCAPE。
图纸资料英语
PACKAGE AND TRANSPORTATION1. 包装箱package装箱单packing list15 花板包装packaged in crate铁路（公路）运输railway highway transportation 水路（海路）运输water(sea) transportation凹形车saddle bottomed wagon落孔车open web girder wagon拖车trailer卡车truck油罐车tanker钳夹式车schnabel wagon起重机hoisting crane浮吊floating crane履带吊 caterpillar crane铁路轨道吊railway crane钢丝绳steel cable手拉葫芦chain block集装箱运输container transport绞盘与滑轮组capstan and pulley block发货日期delivery date到站destination唛头shipping mark小心轻放handled with care不准叠放don’t stack up不准倒置don’t turn over发货人consignor收货人consignee毛重gross weight箱号case No.发货单dispatch list底拖pallet叉车fork lift重心center of gravity限速运输oversize transport不准流放don’t uncouple with slipping装载量loading capacity装货港口port of loading铁路编组站 marshalling yard产品总重total weight of product器身重量weight of active part油重weight of oil运输重 transport weight拆卸附件dismantled accessories备件 spare parts16易损件parts subjected to wear充氮运输transported with nitrogen filling充油运输 transported with oil filling运输尺寸图transportation dimension size铭牌数据rating plate data标志牌，指示牌designating plate , illustration plate指示标记indication mark标准号design code产品代号symbol of product产品序号 serial No.使用条件service condition绝缘水平insulating level海拔高度 working altitude环境温度ambient temperature线圈温升winding temperature-rise线圈端子位置示意图illustrative drawing for winding terminals 线圈连接组图illustrative drawing for winding connection 最大最小分接 maximum (minimum) tapping额定分接rated tappingⅨ图纸及技术文件用语TECHNICAL FOR DRAWING AND TECHNICAL DOCUMENTS零件parts部件component (assembly) parts基础件basic parts借用件shared parts标准件 standard parts外购件general parts附件 accessories配合件 mating parts可拆卸件 dismountable parts成套设备 a complete初步设计preliminary技术设计technical design技术设计说明书instruction for technical design施工图设计 working drawing design技术协议technical agreement技术任务书assignment for technical design技术条件technical condition17合同附件 annex (appendix) to the contract检验鉴定大纲examination and appraisal program 试制总结summary of trial production形式试验报告type test report出厂试验报告 routine test report技术经济分析technical and economical analysis可行性分析 feasibitily study出厂技术文件technical document for product delivery 产品合格证quality certificate变压器使用说明书operation instruction of transformer 总图general layout外形尺寸图overall dimension安装图installation drawing示意图illustrative drawing线路原理图principle circuit diagram方框图block diagram图表table (graph)运输图shipping dimension drawing地基图foundation drawing底图originals (transparent print)蓝图blue print复制图duplicates图样目录contents of drawing (documents) 零件明细表detail list of drawing外购件明细表detail list of purchased parts产品用户一览表reference list of customers图纸标题栏title block of drawing项号 number item名称name图号 drawing No.单件重量unit weight设计，校核，审定designed , checked , approved隶属装配图号pertaining to assembly drawing No. 比例 scale纸型paper size其余for unmarked其余倒角for unmarked edges淬火hardening表面淬火surface hardening镀锌galvanized镀镍nikel ,酸洗pickling18磷化 phosphorated涂两遍底漆coated with two layers of primer表漆 surface coating半导体涂层semi-conducting coating热浸hot dipping防叠层anti-corna coating点固焊tack weld点焊 spot weld标杆焊stud weld配焊 welded according to practical condition 与配合件同时钻孔drilled together with mating parts钻后绞孔 ream after drilling透孔 through hole吹砂（抛丸）shot-blast焊后磨平 grinding to flat after welding去毛刺 clear away burrs回火tempering校直straightening对称件 symmetrical parts锥度孔tapered hole煅件（压铸件）forging (die casting)角钢（槽钢） angle整齐度evenness表面光洁度(粗糙度)finish(roughness)倾斜度inclination圆度（椭圆度）circularity (ellipticity)偏心度（同心度）eccentricity (concentricity)不同心度inconcentricity平（不平）度flatness直度straightness平行度parallelism垂直度perpendicularity展开图unfoldedA-A放大A-A enlargedB-B转B-B tuned byK向viewed from KA-A剖面A-A section对中心（不对中心）alignment冲铆三点锁紧螺母nut locked by punching three points 铆接pieced together改版reverse。
cad绘图常用英语
1fuction1功能区bedstandentrance人口3lightlivingroom客厅droplightnannyroom保姆房absorbdomelightdinningroom餐厅embedlightkitchen厨房dayliggtlampoffice书房reflectdownlightmasterbedroom主卧室quartzdownlightquestbedroomvotagetracklightchildrenbedroom儿童房tracklightprojectionroom视听室picturelightdressingroom更衣室hidinglightstoreroom储藏室walllampmasterbathroomreadinglampbathroom卫生间floorlampwashroom洗衣服4bathroomfixturestaircase楼梯washbowlaiale过道waterfaucetgarden花园closestoolswimmingpool游泳池urinal2furmiture2家具bathtabcupboard厨房橱柜showerbathdrinkbox酒柜floweraspersedbar吧台5wiringdinningtable餐桌televisionchair椅子soundboxrecliningchair躺椅washersofa沙发refrigeratoryteatable茶几macrowaveoventvtable电视柜electriccookerchestdrawers藏衣柜immersionheaterchestdrawers五斗矮柜airconditionbookcase书柜switch化妆台床头柜3灯具吊灯吸顶灯日光灯筒灯石英灯射灯轨道灯镜花灯暗藏灯管壁灯台灯落地灯4卫生洁具洗手台台盆水龙头坐便器小便斗浴缸淋浴房5电器设备电视机音响洗衣机冰箱微波炉电饭煲电热水壶空调开关
工程图常用英语
工程图常用英语(二)作者：未知文章来源：网上收集点击数：189 更新时间：2006-6-15 15:28:38offset section复合剖视compound section剖面图section, sectional view重合剖面coincide section, revolved section移出剖面removed section剖面线section line剖面符号symbols for section-lining习惯画法conventional drawing局部放大图drawing of partial enlargement零件图detail drawing, working drawing第三角投影third angle projection粗实线continuous thick line, full line, visible line细实线continuous thin line虚线dot line, dashed line, hidden line点划线dash and dot line双点划线double dots line波浪线break line断裂线剖切平面迹线cutting plane line尺寸线dimension line尺寸界线extension tine尺寸dimension size箭头arrowhead基准datum基准线datum line基准面datum plane中心孔central hole中心距center distance轴shaft, axle孔hole斜孔inclination装配图assembly drawing性能尺寸characteristic dimension大小尺寸size dimension总体尺寸outer dimension配合尺寸fit dimension内圆角fillet外圆角round尖角sharp corner倒角chamfer轮缘flange of wheel缘、边、环rim轴肩shoulder击台boss凹坑concave pit轴颈shaft neck轮毂hub轮辐spoke, spoke of wheel 直纹滚花straight knurling s 网纹滚花hatching knurling 键槽key-way退刀槽escape拔模斜度pattern draft填料盒gland box油槽oil groove油封oil seal标准件standard parts螺纹thread外螺纹external thread内螺纹internal thread大径major diameter小径minor diameter螺距pitch of thread牙型form of thread旋向direction of turning右旋螺纹right-hand thread 左旋螺纹left-hand thread 头数number of thread导程lead粗牙coarse thread细牙fin thread螺栓bolt螺柱stud螺母nut垫片washer公差tolerance公差带tolerance zone零线zero line标准公差standard tolerance公差等级tolerance grade基本偏差fundamental deviation配合fit间隙配合clearance fit过盈interference过盈配合interference fit过渡配合transition fit基孔制hole-basic system of fits基轴制shaft-basic system of fits间隙clearance形状公差tolerance in form, form tolerance直线度straightness平面度flatness圆度roundness圆柱度cylindricity线轮廓度profile of any line面轮廓度profile of any plane位置公差tolerance in position, position tolerances 平行度parallelism齿轮gear圆柱齿轮cylindrical gear正齿轮spur gear斜齿轮spiral gear轮齿gear tooth节圆pitch circle齿顶圆addendum circle, outside circle齿根圆root circle, addendum circle模数modulus齿数number of teeth齿高tooth height齿顶高height of addendum齿根高height of addendum齿厚circular thickness齿间tooth space齿宽tooth width压力角angle of pressure弹簧spring销pin圆柱销round pin圆锥销taper pin开口销cotter pin, split键key平键flat key半圆键half round key, woodruff key轴承bearing滚动轴承rolling bearing向心铀承radial bearing密封装置sealing equipment锁紧装置locking equipment粗糙度roughness基本尺寸basic size实际尺寸actual size极限尺寸limits size最大极限尺寸maximum limit of size最小极限尺寸minimum limit of size偏差deviation上偏差upper deviation下偏差lower deviation垂直度perpendicularity倾斜度angularity同轴度concentricity对称度symmetry位置度true position跳动run-out圆跳动cycle run-out全跳动total run-out轴测投影axonometric projection轴测投影面plane of axonometric projection轴测图axonometric drawing正等轴测投影isometric projection正二测bimetric projection斜二测oblique bimetric projection轴测轴axonometric axis轴间角axis angle, angle between ales缩短foreshortened轴向缩短率coefficient of axial deformation ratio offore shortening for any axis切割法cutting method, by cutting方箱法boxing method坐标法coordinate method方框法enclosing-square method四心近似法four-center approximate method。
常用机械制图英语
常⽤机械制图英语AA/C across corners 对⾓距A/F across flats 对边距above stuffing上填料accumulation of energy储能accumulation积聚性acme thread梯形(爱克姆)螺纹across corner 对⾓距across flat 对边距actual size实际尺⼨acute angle 锐⾓addendum 齿顶⾼addendum circle 齿顶圆admiralty metal含锡黄铜affiliation从属性(关系)ageing treatment时效处理AL aluminum 铝aligned sectional view旋转剖视图allowance容差、加⼯余量analytical method of line and plane线⾯分析法analytical method of shape形体分析法analyzable assembly分析装配图ANG angle ⾓angle bar or L-bar (beam)⾓钢angle between axonometric axes轴间⾓angular dimension ⾓度尺⼨angular gear⼈字齿轮angular section斜剖⾯angularity倾斜度anneal退⽕anti-clockwise逆时针⽅向的arrow or arrowheads 箭头asbestos packing⽯棉填料ASM assembly 装配(图)、部件assembly drawing number装配图图号assembly drawings装配(组装)图assembly for installation安装图assembly parts装配组合零件assembly sketches装配草图auxiliary circle辅助圆auxiliary plane辅助平⾯auxiliary sectional view斜(辅助)剖视图 aligned and developed展开视图AVG average 平均axial coefficients of foreshortening轴向变形系数axis line 轴线axis of rotation转轴axis轴线axonometric axes轴测轴axonometric drawing轴测图axonometric projection轴测投影BBAB Babbitt 巴⽒(轴承)合⾦back (rear) view后(背)视图bar杆base line 基准线base parts机座base plane底平⾯basic deviation基本偏差basic hole基准孔basic shaft基准轴basic size基本尺⼨BB ball bearing 滚动轴承bearing cover轴承盖bearing set轴承座 bearing轴承bell metal青铜(锡铜)合⾦belt wheel带轮bevel gear斜齿轮BHN Brinell hardness number 布⽒硬度值bisector 平分线blade spring板簧blind hole 盲孔(不通的孔)blind hole盲孔blind threaded hole螺纹盲孔blunt angle 钝⾓body of revolution回转体bolt joint螺栓连接bolt螺栓border 图框border line 图框线boring machine or boring镗床boring镗孔boss club凸台bottom shell 下轴⽡box箱体brazing metal铜锌合⾦bright washer平垫圈Brinell hardness布⽒(HB)硬度broacher拉床、绞孔机broaching拉床、扩孔机broach拉光broken line 断裂线broken view (local view)局部视图BRS brass 黄铜BRZ bronze 青铜burnish or polishing磨光butterfly valve蝶形阀buttress (screw) thread锯齿形(枪膛)螺纹caliper卡尺(钳)cap screw带帽螺钉(栓)capital letters ⼤写字母carburizing (carbon infiltration)渗碳case hardened硬化、表⾯淬⽕casting defect铸件缺陷casting processes铸造⼯艺casting铸造、铸件castle nut内六⾓圆螺母cavity空腔(⽳)CBORE counterbore 沉孔、埋头孔center to center distance 中⼼距centerline (central line) 中⼼线center-to-center spacing中⼼距central projection中⼼投影CH HD cheese head 开槽圆柱头CHAM chamfer 倒⾓chamfer倒⾓channel bar槽钢characteristics of projection 投影特性CHD checked (by) (由) …校对check drawings校(核)图cheese head圆柱头Chinese characters 汉字chrome plating镀铬CI cast iron 铸铁CIR circular 圆的circular arc 圆弧、弧circular pitch 齿距circular pitch周节circular runout圆跳动CL or centerline 中⼼线clamping夹紧clearance fit间隙配合clockwise顺时针⽅向的CM centimeter 厘⽶coarse pitch thread粗⽛普通螺纹coarse wheel粗砂轮加⼯coating涂覆coincidence (revolved) section重合断⾯coincident point重影(合)点color-hardening着⾊硬化、发蓝、发⿊combination solids组合体commom tangent公切线common axis公共轴线common point 共有点compass 圆规component构件compound sectional view复合剖视图concave millstone凹⾯磨盘concentric circle同⼼圆concentricity and coaxiality同轴(⼼)度conic (miter) gear圆锥(伞)齿轮connecting bar连杆construction line 作图线contact surfaces接触表⾯continuous straight thin line with zig zags 折线continuous thick line 粗实线continuous thin irregular line 波浪线continuous thin line 细实线contour arithmetic mean deviation轮廓算术平均偏差contour element外形素线conventional breaks折断规定画法conventional representation规定画法converge聚为⼀点convex millstone凸⾯磨盘coordinate axis坐标轴COP copper 铜copper plating镀铜corrosion腐蚀cotter (split) pin 开⼝(尾)销counterbore hole 阶梯沉孔、埋头孔counterboring tool 平底扩孔钻counter-drill 阶梯钻countersunk hole锥形沉孔、埋头孔coupling or union连轴器covering external thread套扣CP circular pitch 周节crank摇把cross rib⼗字肋cross section shape横断⾯形状crossing line交叉线crossing point交叉点CRS (C to C) centers 中⼼距CSK countersunk 锥孔、埋头孔CU cubic ⽴⽅的CU FT cubic foot ⽴⽅英尺CU IN cubic inch ⽴⽅英⼨CU YD cubic yard ⽴⽅码cube⽴⽅体cuboid长⽅体cup packing⽪碗密封curve template 曲线板curved line of intersection曲交线curved slot 曲线槽cutting plane symbol剖切平⾯符号cutting plane剖切平⾯cut断⾯图cycloidal gear摆线齿轮CYL cylinder (cylindrical) 圆柱、圆柱体的cylindricity圆柱度Ddashed thin lines 虚线datum feature基准要素datum line基准线datum plane基准⾯datum point基准点datum symbo基准代号 ldeburring去⽑刺dedendum circle 齿根圆dedendum 齿根⾼DEG or ? degree 度delineator制图者descriptive geometry 画法⼏何descriptive geometry solution 图解法design datum设计基准DET DWG detail drawing 零件图detail drawing零件图detailing (an assembly drawing) (由装配图)拆画零件图deviation尺⼨偏差（偏差）DIA or φ diameter 直径DIAG diagonal 对⾓线(的)diagonal line 对⾓线diagram assembly drawing装配⼯作图diagrammatic drawing⽰意图diameter 直径diamond knurling⽹纹滚花dimension 尺码dimension figure 尺⼨数字dimension form 尺⼨格式dimension line 尺⼨线dimension text 尺⼨数值dimension tolerance尺⼨公差dimetric drawing正⼆轴测图dividers 分规dome圆顶状double-start thread双线螺纹dowel pin 圆柱销draft or draught起模斜度drafting paper 绘图纸drafting tape 胶带纸drawing board 图板drawing number图号DRG drawing 制图、图样drilling钻孔drive gear主动齿轮driven gear从动齿轮driven shaft从动轴DRN drawn (by) (由) …绘图ductile cast iron球墨铸铁dynamometry测⼒Eedge line棱线effective diameters弹簧中径effective length有效长度EI or ei 来⾃法⽂ecart inferieur 下偏差代号elbow肘形弯管(头) element circle素线圆element symbol基本符号elementary unit基本体ellipse椭圆elongated hole延长孔、拉伸孔end cover端盖end face端⾯end point端点engineering requirements技术要求enlarged partial view局部放⼤图enlargement scale 放⼤⽐例EQUI SP or EQS equally spaced 均布erasing shield 擦图⽚ES or es 来⾃法⽂ecart superieur 上偏差代号EXT external 外部的extension line 尺⼨界线external (male) thread外(阳)螺纹external diameter弹簧外径external dimension外形尺⼨external tangency 外切external thread lathing车外螺纹external view外形视图extreme position of moveable part 活动极限位置extruding挤压FFAB fabricate 制造、装配faucet旋塞、⽔龙头feed spiral送料螺旋felt ring毡圈ferrous metal⿊⾊⾦属FIG. figure 附图、插图FIL fillister 凹槽file锉filing margin 装订边fill in填写fillet铸造(内)圆⾓fine boring精镗fine broaching精拉fine grinding精磨fine milling精铣fine pitch thread细⽛普通螺纹fine planning精刨fine turning精车finish all over全部加⼯fissure裂纹fit symbol配合代号fit system配合制fit配合55? non sealing pipe thread 55?⾮密封管螺纹55? sealing pipe thread 55?密封管螺纹fixed body固定钳⾝flange法兰盘、凸缘flat bar扁钢flat heads平顶flat or plane平⾯flatness平⾯度follower从动(⼤齿)轮font 字体font cavity缩孔、铸⼝forging锻压fork拨叉form error形状误差forth quadrant第四象限four quadrants四个象限45? mitre line 45?斜线free hand 徒⼿(画)free height⾃由⾼度frontal line正平线frontal plane (or V-plane)正投影⾯frontal plane正平⾯frustum of a cone圆锥台frustum of a cone截头圆锥frustum of a pyramid棱锥台FT or ′foot 英尺full sectional view全剖视图full size 原值⽐例full thread全螺纹functional dimensions功能尺⼨Ggasket密封垫(圈)gauge calipers卡(量)规gear box (case)齿轮箱gear train齿轮传动gear齿轮general fit class配合种类general-plane ⼀般位置平⾯general-position line⼀般位置直线generating circle母线圆generator (generation) line母线Geometric construction ⼏何作图geometrical solid⼏何体geometrical tolerance symbol形位公差符号geometrical tolerance形状位置公差GI galvanized iron 马⼝铁、镀锌铁gib-head key钩头楔键gland压盖gland密封压盖globe valve球阀good-quality carbon steel优质碳素钢grade 坡度grade A and grade B of type one hexagon nutI 型六⾓螺母A级和B级graduated scale ⽐例(分度)尺graphical representation 图⽰法Graphics 图学GRD grind 磨削grey cast iron灰⼝铸铁grinding machine磨床grinding研磨grinding磨削groove 凹槽、沟纹guard valve安全阀guide pin定位销guide screw丝杠Hhalf sectional view半剖视图half view半视图hand valve⼿压阀hard casting⽩⼝铁hard metal硬质合⾦hardened and tempered调质的harden淬⽕hardness number硬度值Hatching 剖⾯线heat-treatment热处理heavy lines 加深图线heavy metal重⾦属helical compression spring圆柱螺旋压缩弹簧helical spring螺旋弹簧helical spur gear斜齿圆柱齿轮helical tension spring圆柱螺旋拉伸弹簧herringbone gear⼈字形圆柱齿轮HEX hexagon 六⾓(边)形HEX HD hexagon head 六⾓头hex nut六⾓螺母hex slotted nut六⾓开槽螺母hexagon head 六⾓头hexagon head bolt六⾓头螺栓hexagon head bolt六⾓头螺栓hexagon socket cap screw内六⾓圆柱头螺钉hexagon thin nut六⾓薄螺母hidden edges 不可见轮廓线high-carbon steel⾼碳钢high-speed steel⾼速钢hole-basis system of fits基孔制配合horizontal (level) plane⽔平⾯horizontal line⽔平线horizontal projection plane (H-plane)⽔平投影⾯hot-rolled steel热轧钢HP horsepower 马⼒H-perpendicular line铅垂线H-perpendicular plane铅垂⾯HR hour ⼩时hub轮毂hub轮毂、中⼼hyperbola双曲线Ihypotenuse直⾓三⾓形之斜边(弦)I/D inside diameter 内径、内形尺⼨I-beam⼯字钢imaginary line 假想线IN or ″ inch 英⼨incenter 内(切圆)⼼included angle夹⾓inflexion拐点ingot iron低碳钢(⼯业纯铁)initial outline 初始轮廓线inlet side⼊⼝端inner race内圈inside diameter内径instruction book说明书instrumental drawing ⽤仪器画的图INT internal 内部的interchangeability互换性interference fit过盈配合internal (female) thread内(阴)螺纹internal (inside) caliper内卡尺(钳) internal diameters弹簧内径internal tangency 内切internal thread lathing车内螺纹interpenetration相贯intersecting plane截平⾯intersection line截交线intersection of plane surfaces平⾯之交线intersection of surfaces表⾯之交线intersection point交点Intersection相交Intuitive illustrations直观图involute gear渐开线齿轮iron铁ISO standards ISO国际标准ISO=International Standardization Organization国际标准化组织isometric drawing (diagram)正等轴测图isometric projection正等测投影isometric sectional view正等轴测剖视图Italic font 斜体Jjack千⽄顶、起重器jig body夹具体junction surface结合⾯Kkey diagram原理草图key joint键连接key seat键座key types键的型式key way (slot)键槽key键knobbled (wrought) iron熟(锻)铁knurling 滚花knurling nut滚花螺帽Llamp plank钳⼝板LAT lateral 侧(横)向的lathe车床LB pound 磅lead distance导程leader line 指引线lead导程leaf spring叶(薄)⽚弹簧left hand-thread左旋螺纹left-hand side (end) view左(端)视图length of thread engagement螺纹旋合长度letter 字母lever arm长臂杠杆LG long .length 长度、长的LH left hand 左旋、左⽅向light metal轻⾦属limit size极限尺⼨limiting deviations极限偏差limiting element转向轮廓素线LIN linear 线性的、直线的line segment 线段line styles 线型linearity直线性lines in planes线在⾯上L-iron⾓铁local (broken-out) sectional view局部剖视图location by dimension 定位尺⼨location dimension尺⼨定位lock nut防松螺母lock screw锁紧螺钉locking device锁紧装置LONG longitude 经度(线)long dashed dotted thin line 点画线long dashed double dotted thin line 双点画线lower-case letters ⼩写字母lower deviation下偏差lower limit下限(值)lubricant pump齿轮油泵。
图纸常用英语模板
复合剖视compound section剖面图section, sectional view重合剖面coincide section, revolved section移出剖面removed section剖面线section line剖面符号symbols for section-lining习惯画法conventional drawing局部放大图drawing of partial enlargement零件图detail drawing, working drawing 第三角投影third angle projection粗实线continuous thick line, full line, visible line细实线continuous thin line虚线dot line, dashed line, hidden line点划线dash and dot line双点划线double dots line波浪线断裂线break line剖切平面迹线cutting plane line尺寸线dimension line尺寸界线extension tine尺寸dimension size 箭头arrowhead基准datum基准线datum line基准面datum plane中心孔central hole中心距center distance轴shaft, axle孔hole斜孔inclination装配图assembly drawing性能尺寸characteristic dimension 大小尺寸size dimension总体尺寸外形尺寸outer dimension配合尺寸fit dimension内圆角fillet外圆角round尖角sharp corner倒角chamfer轮缘flange of wheel缘、边、环rim轴肩shoulder凸台boss凹坑concave pit轴颈shaft neck轮毂hub轮辐spoke, spoke of wheel 直纹滚花straight knurling s 网纹滚花hatching knurling 键槽key-way退刀槽escape拔模斜度pattern draft填料盒gland box油槽oil groove油封oil seal标准件standard parts螺纹thread外螺纹external thread内螺纹internal thread大径major diameter小径minor diameter螺距pitch of thread牙型form of thread旋向direction of turning 右旋螺纹right-hand thread 左旋螺纹left-hand thread 头数number of thread导程lead 粗牙coarse thread细牙fin thread螺栓bolt螺钉screw螺柱stud螺母nut垫片washer公差tolerance公差带tolerance zone零线zero line标准公差standard tolerance公差等级tolerance grade基本偏差fundamental deviation配合fit间隙配合clearance fit过盈interference过盈配合interference fit过渡配合transition fit基孔制hole-basic system of fits基轴制shaft-basic system of fits间隙clearance形状公差tolerance in form, form tolerance直线度straightness平面度flatness圆度roundness圆柱度cylindricity线轮廓度profile of any line面轮廓度profile of any plane位置公差tolerance in position, position tolerances平行度parallelism齿轮gear圆柱齿轮cylindrical gear正齿轮spur gear斜齿轮spiral gear轮齿gear tooth节圆pitch circle齿顶圆addendum circle, outside circle 齿根圆root circle, addendum circle模数modulus齿数number of teeth齿高tooth height齿顶高height of addendum齿根高height of addendum齿厚circular thickness齿间tooth space齿宽tooth width 压力角angle of pressure弹簧spring销pin圆柱销round pin圆锥销taper pin开口销cotter pin, split键key平键flat key半圆键half round key, woodruff key 轴承bearing滚动轴承rolling bearing向心铀承radial bearing密封装置sealing equipment锁紧装置locking equipment粗糙度roughness基本尺寸basic size实际尺寸actual size极限尺寸limits size最大极限尺寸maximum limit of size 最小极限尺寸minimum limit of size 偏差deviation上偏差upper deviation下偏差lower deviation垂直度perpendicularity倾斜度angularity同轴度concentricity对称度symmetry位置度true position跳动run-out圆跳动cycle run-out全跳动total run-out轴测投影axonometric projection轴测投影面plane of axonometric projection轴测图axonometric drawing正等轴测投影isometric projection正二测bimetric projection斜二测oblique bimetric projection轴测轴axonometric axis轴间角axis angle, angle between ales缩短foreshortened轴向缩短率coefficient of axial deformation ratio offore shortening for any axis切割法cutting method, by cutting方箱法boxing method坐标法coordinate method方框法enclosing-square method 四心近似法four-center approximate method机械工程图中常用的英语词汇Abbreviation 缩写Accuracy 精度、准确性Acme thread 梯形螺纹(29°) Addendum 齿顶高Addendum angle 齿顶角Addendum circle 齿顶圆Addendum of mating gear 啮合齿轮的齿顶高Adjacent-part lines 相邻零件线Aligned sections 旋转剖视Aligned view旋转视图Allowance 容差、加工余量Alloy 合金Alloy steel 合金钢Alphabet 字母Alteration 变更、更改Alternate-position views 位置改变的视图Alternator 交流发电机Induction alternator 感应(交流)发电机Motor alternator 电动(交流)发电机Single-phase alternator 单向(交流)发电机Synchronous alternator 同步(交流)发电机Three-phase alternator 三相(交流)发电机Amount 总量、总计Analyzable assembly 分析装配图Anchor bolt 地脚螺栓Angles 角Acute angle 锐角Blunt angle 钝角Right angle 直角Sliding angle 摩擦角Spiral angle 螺旋角Taper angle 锥角Angular 有角的Angular bearing 径向止推轴承Angular bevel gears 斜交伞齿轮Angular gear人字齿轮Angular section斜剖面Anneal 退火Approval 批准、许可Arc 弧、圆弧Arc thickness 弧长厚度(齿厚)Arc welding 弧焊Arrangement 布置、装置Arrangement of views 视图的布置Clamping arrangement 夹紧装置Cramping arrangement 紧固装置General arrangement 总体布置Arrow 箭头Arrowheads 箭头Assembly 装配图、组装图Assembly drawing 装配图Assembly drawing number 装配图图号Assembly for installation 安装图Assembly parts 组装配合零件Assembly sections 装配图剖视Assembly sketches 装配草图Auxiliary elevation 辅助立面图Auxiliary line辅助线Auxiliary section 辅助剖视Auxiliary surface 辅助面Auxiliary view 辅助视图Average 平均数Axial 轴的、轴向的Axial pitch 轴向节距Axial plane 轴向平面Axial thickness 轴向厚度Axis 轴线、中心线Axis of revolution 回转轴线Axis of rotation 旋转轴线Axis of symmetry 对称轴线Horizontal axis 水平轴Major axis 长轴Minor axis 短轴Vertical axis 垂直轴X axis X轴Y axis Y轴Axle 轴Axle bearing 轴向(止推)轴承Axle sleeve 轴向(止推)套筒Axonometric drawing 轴测图Babbitt 巴氏合金Back cone 背锥Back cone radius 背锥半径Back elevation 后视图Backstop 托架、棘爪Ball bearing 球轴承Bar 杆Angle bar 角钢Channel bar 槽钢Flat bar 扁钢Round bar 圆棒、圆钢Base 基础、底座、基线、基面、基准Base circle 基圆Base circular thickness 基圆弧线齿厚Base cylinder 基圆柱Base helix angle 基圆上的螺旋角Base plane 基平面Base point 基点Key base 键座Basic circle 基准圆Basic hole system 基孔制Base shaft system 基轴制Basic size 基本尺寸、公称尺寸、标称直径Basis 基础、基准、基线Battery 电池、蓄电池Bearing 轴承、支撑、方位Bearing accuracy 定位精度Bearing box 轴承箱Bearing brass 铜轴衬Bearing bridge 轴承支架Bearing oil seal 轴承油封圈Bearing support 轴承架Bearing unit 轴承组合件Anti-friction bearing 减摩轴承Ball and socket bearing 球窝轴承Conical bearing 锥形轴承Journal bearing 径向轴承Needle bearing 滚针轴承Plain bearing 滑动轴承Roller bearing 滚柱轴承Self-aligning bearing 自位轴承Thrust bearing 止推轴承Belt 带、皮带Bench 工作台Work bench 工作台Bend 弯头、接头Elbow bend 肘形弯管Normal bend 正弯管(90°) Bender 弯曲机Bending 挠曲Bending strength 抗弯强度Bent axle 曲轴Bevel 倾斜的、斜角的、斜面Bevel gear 圆锥齿轮、伞齿轮Bevel pinion 小圆锥齿轮Bevel washer 斜垫圈Bevel wheel 伞齿轮、斜摩擦齿轮Bilateral tolerance 双向公差Bill of materials 送料单Block in、block out 画草图Blue paper 蓝晒纸Blueprint 蓝图、设计图Board 板、(管理)局、厅Bottom board 底板Moulding board 模板Body 机体、机身Boiler 锅炉Bolt 螺栓、插销Adjusting bolt 调整螺栓Assembling bolt 装配螺栓Binding bolt 连接螺栓Bright blot 光制螺栓Captive bolt 固定螺栓Double-screw bolt 双头螺栓Fitter bolt 装配螺栓Foundation bolt 地脚螺栓Hexagonal head bolt 六角头螺栓Hook bolt 钩形螺栓Screw bolt 全螺纹螺栓Snap bolt 圆头螺栓Tension bolt 拉紧螺栓Bolted joints 螺栓连接Book 书、册Hand book 手册Instruction book 说明书Bore face machine 镗孔端面加工机床Borer 镗床Jig borer 坐标镗床Table borer 台式镗床Boring 镗孔Boring machine 镗床Boring mill 镗床Bottom case 底座Bottom clearance 径向间隙Bottom view 底视图Bracket 托架、支柱Brake 制动器、闸Brass 黄铜、铜轴衬Braze 铜焊Brazing 铜焊Breadth 宽度、厚度Break line 断裂线Brinell figure (number) 布氏硬度Brinell hardness 布氏硬度Broacher 拉床、绞孔机Broaching 扩孔机、拉床、拉削Broken circle 虚线圆Broken out section 断裂剖面Broken view 局部视图Bronze 青铜Burnishing 抛光、磨光Burr 三角矬、毛刺、去毛刺Bush 衬套、轴瓦Bushing 轴衬、衬套、套管Butt joint 对接焊Butterfly nut 蝶形螺母Butterfly valve 蝶形阀Button 按钮Push button 控制按钮Cable 电缆Cage 盒、罩、箱Caliper 卡尺、卡钳Gauge caliper 卡规、量规Internal caliper 内卡钳Sliding (vernier) caliper 游标卡尺Cam 凸轮Cam design 凸轮设计Cam shaft 凸轮轴Actuating cam 主动凸轮Adjustable cam 可调凸轮Control cam 控制凸轮Cap 盖、帽、罩Cap screw 带帽螺钉Capital 大写字母Carburizing 渗碳Card 卡片Cartographer 制图员Cartography 制图学、制图法Case 箱、盒、容器、表面Case hardened 表面淬火、硬化Nitrogen case hardening 渗氮硬化Casing箱、盒、壳Oil pump casing 油泵(壳) Casting 铸造、铸件Defect casting 铸件缺陷Die casting 压铸Sand casting 砂型铸造Spun casting 离心铸造Steel casting 铸钢Cast-iron 铸铁Castle circular nut 六角圆螺母Castle nut 蝶形螺母Catalogue data 表列数据Cave 凹槽、内腔Centre 中心、圆心Centre distance 中心距Centre hole 中心孔Centre line 中心线Centre-section 中心剖面Centre to centre 中心距Centesimal 百分的、百分之一的Centimeter 厘米、公分Central hole 中心孔Central plane 中心平面Central projection 中心投影Chafe 摩擦、磨损Chain 链Drive chain 主动链Transmission chain 传动链Chamfer 倒角、倒棱、斜面Dimensioning of chamfer 倒角的尺寸注法Changes on drawing 图的更改Channel 沟槽Chapter 章Chart 图表、计算图Chart of symbols 符号图表Auxiliary chart 辅助图Dimensions chart 外廓尺寸图Graphical chart 图表Process chart 工艺程序图Progress chart 工艺程序表、工作进度表Charting 制图(表)、填图Check 校验、校核、制动装置Check drawings 校图Check nut 防松螺母Check ring 挡圈Check test校核试验Chief draftsman 主任制图员Chromium 铬Chromizing 镀铬处理Circle 圆、圆周Circle of reference 参考圆Addendum circle 齿顶圆Base circle 基圆Graduated circle 分度圆Imaginary circle 虚圆Outside circle 齿顶圆、外圆Pitch circle 节圆Rack circle 平面齿轮、扇形齿轮Root circle 根圆Top circle齿顶圆Circular cylinder 圆柱Circular pitch 弧线节距Circular thickness 弧线(齿)厚度Circumference 圆周长Clamp 夹紧、夹板Class 种类Class of fit 配合级别Classification 分类Claw 爪、钩、卡爪Clearance fit 间隙配合Clevice /clevis U形钩、U形夹Clevis bolt 套环(插销)螺栓Clevis pin U形夹销Clockwise 顺时针方向Clutch 离合器、联轴器Coat 外层、涂镀层Coat of metal 金属镀层First coat 底漆Coating 镀、覆盖Electrodeposited coating 电镀层Coaxial circle 共轴圆Cock 旋塞Coil 蛇形管、螺管、线圈Coil spring 盘簧Coincident line 重叠线Cold-rolled steel 冷轧钢Collet 夹头Collet chuck 弹簧夹头Color-harden 着色硬化、发蓝、煮黑Common difference 公差Company 公司Joint company 股份公司Limited company 有限公司Compass 圆规Compass of proportion 比例规Component 零件、构件Compression spring 压力弹簧Compressor 压缩机Computer 计算机Concave face 凹面Concentricity 同心度Cone 圆锥Cones development 锥面展开Cone pulley 锥形轮、塔轮Conical spring 锥形弹簧Connection 联接Bolt-on connection 螺栓联接Flange connection 法兰联接Rivet connection 铆钉联接Screw connection 螺钉联接Contact 接触、接合、啮合Contact angle 啮合角Angular contact ball bearing 向心止推球轴承Contour 外形、轮廓线Contracted drawing 缩图Contrast 对比、对照、比较Convention 惯例、常规、习惯Convention for materials 材料的习惯表示法Conventional break 习惯断裂画法Conventional diagram 习惯画法Conventional intersection 习惯交线(画法)Conventional practice 习惯画法Conventional sign 图例、习惯符号|Convex 凸面Conveyer 输送机、传送机Cooler 冷冻机Coordinate axis 坐标轴Coordinate paper 方格纸、坐标纸Copper 铜Copy 抄本、样板Correction 校正、修正Cotter pin 开口销Split cotter 开口销Counterbore 埋头孔、锥口孔Counterclockwise 逆时针方向Countersink 埋头孔、沉孔Countersink drill 中心钻、钻Countersunk 钻埋头孔、钻锥口孔Countersunk bolt 埋头螺钉Countersunk head 埋头Countersunk hole 锥坑Coupling 联轴节Cover 盖、罩Cylinder cover 汽缸盖Dust cover 防尘罩Cowl 壳、套、盖Crane 起重机Crank 曲柄、曲轴Crankshaft 曲轴Crest 峰、尖、牙尖Cross head 十字头Cross section 横剖面、横断面Crown gear 冕状齿轮Cube 立方形体、正六面体Current 电流Curvature 曲率Curvature radius 曲率半径Curve 弯曲、曲线、曲线板Curve plotter 绘图仪Curve ruler 曲线板French curve 曲线板Moment curve 力矩曲线、力矩图Cutter 刀、刀具Cutting plane 截平面Cutting plane symbols 剖切(迹线)平面符号Cycloid 摆线Cycloidal gear 摆线齿轮Cylinder 圆柱体Cylinder base 汽缸座Pump cylinder 泵缸Cylindrical cam 圆柱凸轮Cylindrical fit 圆柱配合Cylindrical roller bearing 圆柱滚子轴承Dash 短划线、虚线、破折号Dash and dot line 点划线Broken dash 断裂线Data 数据、资料Engineering data工程数据Master data 主要数据Date 日期、年代Datum 基准(点、线、面)、资料Datum line 基准线Datum point 基准点Datum plane 基准面Decade 十进制、十进位Decelerator 减速器、制动器、缓动装置Decimal 小数的、十进位小数的Decimal fraction 十进制分数Decimal fraction system 十进小数制Decimal scale 十进位比例尺Decimeter 分米、公分Dedendum angle 齿根角Dedendum circle 齿根圆Definition 定义Deformation 变形、扭曲Degree 度、程度Degree of accuracy 精度Degree of freedom 自由度Degree of hardness 硬度Degree scale 刻度Circular degree 圆度Delineation 轮廓、草图Delineator 制图者Department 科、处、系、车间Draft department 设计科Engineering department 技术科Fitting department 装配车间Heat treatment department 热处理车间Mechanical department 机加工车间Processing department 工艺科Depth 深度、高度Depth dial gauge 深度千分表Depth of engagement 啮合深度Depth of thread 螺纹深度Depth of tooth 齿高Contact depth of tooth 啮合高度Working depth of tooth 齿工作高度Derivation 偏差Standard derivation 标准偏差Description 描述、作图、绘制Design 设计、计划Design activity 设计机关(组织) Design assembly 设计装配图Design drawing 设计图Design layout 设计草图、初步设计图Preliminary design 初步设计Standard design 标准设计Technical design 技术设计Designation 符号、标志Designation strip 铭牌Designer 设计员、制图者、设计师Desk 桌、控制台Drawing desk 绘图桌Detail 细目、细节、详图、零件Detail drawing 详图、零件工作图Detail paper底图纸、描图纸Detail specification 详细规格Detent 棘爪、扳手、制动器Developable surface 可展曲面Developed view 展开图Development inner port 内表面展开图Development of surface 表面展开图Deviation 偏差、偏移Angular deviation 角偏差Average deviation 平均偏差Standard deviation 标准偏差Tolerance deviation 允许偏差Device 装置、设备Diagram 示意图、图解Diagram drawing 图解图、结构图Arrangement diagram 布置图Assembly diagram 装配示意图Block diagram 方框图Schematic diagram 原理图、简图Diagrammatic drawing 草图、示意图Dial gauge 千分表Dial inside micrometer 内径千分表Diameter 直径Diameter of aperture 孔径Diameter of pitch circle 节圆直径Diameter pitch (齿轮)径节Diameter run-out径向跳动Major diameter 大直径、螺纹外径Minor diameter 小直径、螺纹内径Nominal diameter 公称直径Pitch diameter of screw thread 螺纹中径Thread diameter 螺纹外径(直径) Diametral pitch 齿轮径节Die 模具、扳牙Diesel 柴油机、内燃机Dimension 尺寸Dimension line 尺寸线Limiting dimension 极限尺寸Nominal dimension 公称尺寸Outer dimension 外形尺寸、轮廓尺寸Direction 方位、方向Clockwise direction 顺时针方向Disc = disk 圆盘、原板Disk cam 圆盘凸轮Dismount 拆卸Dismountable 可拆卸的Displacement 移位、变位Distance 距离、路程Distortion 变形、歪扭Distribution 分配、分布、配置Ditto machine 复印机Diversion 变更、转换Dividing head 分规Dot line 虚线Dotted line 虚线Double dots line 双点划线Double helical pinion 人字小齿轮Double helical spur gear 人字齿轮Double thread 双头螺柱Dowel thread 定位销、圆柱销Dozer 推土机Draft = draught (拔模)斜度、草图、制图Drafting 制图Drafting board 制图板Drafting machine 制图机Drafting tape 制图带、胶带Draftsman 绘图员Drawer 制图员Drawing 绘图、图样Drawing board 绘图纸Drawing control 图样管理Drawing free-head 草图Drawing instrument 绘图仪器Drawing number 图号Drawing pencil 绘图铅笔Drawing pin 图钉Drawing size 图纸尺寸Drawing table 制图桌Drawing with compass 用圆规画图Blue print drawing 蓝图Free hand drawing 徒手图Full size drawing 原大图Skeleton drawing 草图、结构图Working drawing 施工图、制造图、工作图Drill 钻孔、穿孔、穿孔器Drive 传动、驱动Drive fit 打入配合Air drive 气动Belt drive 带传动Chain drive 链传动Friction drive 摩擦传动Gear drive 齿轮传动Hydromatic drive 液压传动Speed-reducer drive 减速器传动Variable-speed drive 变速传动Worm-wheel drive 蜗轮传动Driven gear 从动齿轮Driven shaft 从动轴Driving gear 主动齿轮Driving shaft 主动轴Drum cam 凸轮轴Ductile iron 球墨铸铁Duplicating tracing 复制描图Durometer (钢轨)硬度计Dusting cloth 抹灰布、撒粉布Eccentricity 偏心距Edge iron 角铁Edge round 外圆角Edge view 边视图Effective diameter 有效直径Effective face width 有效齿宽Efficiency 效率、性能Mechanical efficiency 机械效率Elastic deformation 弹性变形Elasticity 弹性Elbow 肘形弯管、弯头Electric current 电流Electric element 电池Elephant 绘图纸(28X23英寸) Elevation 正面图、立视图End 末端、头Ball end 秋端Butt end 平端、端面Tail end 尾端Top end 顶端Engagement 啮合Engineer 工程技术人员、工程师Engineer-in-chief 总工程师Equipment 设备Eraser 橡皮Erasing shield 擦图片Erection diagram 安装图、装配图Error 误差Accumulated error 累积误差Allowance error 容许误差Average error 平均误差Permissible error 容许误差Relative error 相对误差Exterior 外表面External 外部External diameter 外径External dimension 外形尺寸External fillet 外圆角External thread 外螺纹Extra fine(screw)特细牙螺纹Eyelet = eyelet-hole 小孔Fabrication 建造、制造Face 面、正面、表面、端面Face cam 平面凸轮Face gear 平面齿轮Face hardening 表面硬化Inner face 里面Outer face 外面Face off 倒角Factor of safety 安全系数Factory 工厂、制造厂Factory made 工厂制造的Fastener 接合件、紧固件Fastening 连接件、紧固件Fatigue 疲劳Faucet 旋塞、龙头、开关Feather 滑键、冒口Feather key 滑键Feature 特征、特性、性能Basic mechanical design feature 主要机械设计性能Mechanical feature 机械性能(特性) Feed-pump 供油泵、供水泵Feet 英尺Ferrous metal 黑色金属Field 工场、现场Figure 形状、图样、插图、数字File 锉刀、锉平Filler 填料、垫片Fillet (内)圆角、填角、嵌条Fillet radius 内圆角半径Filter 过滤器Fine thread series 细螺纹级(系列) Finish 完工、加工、磨光Finish all over 全部加工Finish marks 加工符号Machine finish 机器光制Fit 配合Clearance fit 间隙配合Free fit 自由配合Interference fit 静配合Light press fit 轻压配合Light running fit 轻传动配合Loose fit 松配合Normal-running fit 传动配合Running fit 动配合Shrink fit 冷缩配合Slide fit 滑动配合Transition fit 过渡配合Fix 安装、装配、调整、修理、固定Flange 法兰盘、凸缘Flank 边、侧面、齿侧、后面Flat 扁头、平面Flat key 平键Flat spring 板弹簧Flat surface 平面Flexible disk coupling 挠性盘形联轴节Flexible gear-type coupling 挠性齿轮联轴节Flywheel 飞轮Foot 英尺Foot screw 地脚螺钉Force 力Fore word 序、前言Forge 锻Forge steel 锻钢Former 样板、模型、量规Wooden former 木模Formula 公式Foundation 基础、基座Foundation bolt 地脚螺栓Foundry 铸件、铸工车间Fraction 分数、小数Front view 前视图、主视图Full diameter 大直径、主直径Full line 实线Full size 原大Full scale 原大Full section 全剖视Full section view 全剖视图Furbish 研磨、擦光Fuse 保险丝、熔断器Gage = gauge 量规Gallon 加仑Galvanize 镀锌、电镀Gasket 垫圈、密封垫Gasket material 填料Gasoline engine 汽油(内燃)机Gate 门、阀门Gear 齿轮Gear addendum angle 齿顶角Gear box(case) 齿轮箱Gear centre 齿轮中心Gear dedendum angle 齿根角(圆锥齿轮) Epicyclic gear 行星齿轮Herringbone gear 人字齿轮Ratchet gear 棘轮General drawing 总图Geometry 几何学Gland 压盖、填料盖、密封装置Glass 玻璃Glasscloth 砂布、玻璃布Glossary 词汇(表)Grade 等级、斜度Steel grade 钢号Graduated hardening 分级淬火Graduated scale 比例尺、分度尺Gram 克Graph 图(表、解、形)、曲线图Graph paper 方格纸Graphic图示、制图学Grease 滑脂Grind 磨削、抛光Grinding machine 磨床Grinding wheel 砂轮Groove cam 槽凸轮Groove pulley 槽轮、三角带轮Guide 手册、指南Guide bar 导杆Guide pin 定位销、导向销Guide screw 丝杠Guidebook 参考手册、指南、入门Half 二分之一、一部分Half bearing 轴瓦Half section 半剖视Half section view 半剖视图Hammer 锤子Handbook 手册、指南Hand-made 手工制造的Hand-operated 手控的Handle 手柄Hand wheel 手轮Hard casting 白口铁Hard drawn 冷拔Hard rolled 冷轧的Hard surfacing 表面硬化Harden 淬火、硬化Hardened and tempered 调质的Hardened-steel 淬火钢Hardening 硬化Hardness 硬度Hardometer 硬度计Hatch 剖面线H-beam 工字梁、H形梁Heat–treatment 热处理Heavy force fit 重压配合Height 高度Helical bevel gear 螺旋伞齿轮Helical gear 螺旋齿轮、圆柱斜齿轮Helical rack 斜齿齿条Helical spring 螺旋弹簧Hex nut 六角螺母Hexagon jam nut 六角锁紧螺母Hexagon socket head 内六角头Hidden line 虚线Hidden outline 看不见的轮廓线High-carbon steel 高碳钢High-duty 重型的、大型的、优产的High-speed steel 高速钢Hosting jack 千斤顶Hole 孔Horizontal datum plane 水平基准面Horizontal line 水平线Horizontal projection 水平投影Horizontal projection plane 水平投影面Horse-power 马力、功率Hose 软管Hose coupling 软管接头Hot-rolled steel 热轧钢Hot-work 热加工Hour 小时Housing 机座Housing of pump 泵体Bearing housing 轴承箱Gear housing 齿轮箱Hub 轮、中心、衬套I-beam 工字钢Illustration 插图、实例Inaccuracy 不精确、不准确Incenter 内(切圆)心Inch 英寸Incline 斜度、斜面Index plate 分度盘Indicator 指示计、百分表Industrial 工业公司Industrial drawing 工业制图Industry 工业Inertia 惯性Ink 墨水、油墨Ink holder 钢笔杆China ink 墨汁Inscription 标题Inside diameter 内径Inspection 检修、检查Inspection machine 检修机器Inspector 检查员Installation 装置、设备、安装Installation diagram 安装图Institute 研究所、协会、学院、学会Instruction 说明、指示Instrument 仪器、仪表、工具Instrument drawing 仪器图Intensity 强度Interchangeability 互换性1 Interconnection 互相连接Interference fit 静配合Interior view 内部(的)视图Internal combustion engine 内燃机Internal fillet 内圆角Internal gear 内齿轮Introduction 引言、介绍、序言Invisible line 虚线Involute 渐(伸)开线Involute gear 渐开线齿轮Involute rack 渐开线齿条Involute spline 渐开线花键Involute teeth 渐开线齿形Iron 铁Ingot iron 低碳铁、工业纯铁Knobbled iron 熟铁Magnetic iron 磁铁Malleable iron 可锻铁、韧性铁Plate iron 铁板、钢板Quadrant iron 方钢Rod iron 圆铁、棒钢Round iron 圆铁、圆钢Rustless iron 不锈铁Section iron 型钢Structural iron 结构钢White iron 白口铁Wrought iron 熟铁、锻铁Isometric diagram 等轴测图Isometric drawing 等轴测图Jack-screw 螺旋千斤顶Job sheet 零件图纸Joint 结合、连接、焊接Bolt joint 螺栓连接Riveted joint 铆钉连接Welded joint 焊接Journal 轴径Journal bearing 径向轴承Keeper 保持器(片)、架、定位件卡箍Keep-ring 保持环Key diagram 键、按钮Key way(seat、seating、slot)键槽Key wrench 套筒扳手Gib-head taper key 钩头斜键Square key 方形键Tightening key 斜扁键Woodruff key 半圆键Key-bolt 键螺栓Kilogram(me)公斤、千克Kilogram-meter 公斤米、千克米Kilometer 公里、千米Kilovolt 千瓦Kilowatt 千伏Kit 一套工具Knee 弯头、升降台Knee bend 弯管Knob 捏手、按钮Knuckle thread 圆形螺纹Knurl 滚花、压花Knurled nut滚花螺母L-bar = L-beam 角钢Laboratory 实验室、研究室Lamp 灯Alarm lamp 信号灯Daylight lamp 日光灯Incandescent lamp 白炽灯Indicating lamp 信号灯、指示灯Lantern 游环、套环Large compasses 大圆规Lathe 车床Lathe-hand 车工Lattin = Latten 金属薄板、黄铜片Law 规律、定律Lay 布置、安排、放置Layer 层Carburized layer 渗碳层Layout 计划、方案、草图Layout design 草图设计、方案设计Layout drawing 方案草图Lead angle 螺旋升角Lead line 指引线Leaf spring 板弹簧Left hand 左方向Left hand thread 左旋螺纹Legend 图例、图表符号、代号、说明书Length 长度、距离Length gauge 长度规Length of normal 法线长Length of side 边长Effective length 有效长度Lens 透镜、镜片Letter 字、字母Capital letter 大写字母Level surface 水平面Lift 升降机、电梯Light alloy 轻合金Light beam 光束Light series 轻系列Light-duty 轻型Lighting installation 照明装置Lightning switch 照明开关Liquid 液体Limit 极限尺寸Limit switch 限位开关Line 线Line of action (齿轮)压力线Line of contact (齿轮)接触线Line of shaft轴线Line of thickness 线型的粗度Line weight线的粗细程度Actual line实线Addendum line齿顶线Broken line断裂线Center line = central line中心线Continuous line实线Dash(ed) line虚线Diagonal line 对角线Imaginary line 假想线Generation line 母线Pitch line 节线Real line 实线Reference line 基准线、参考线Right line 直线Skeleton line 轮廓线Solid line 实线Straight line 直线Vertical line 垂直线Liner 衬套Bearing line 轴瓦Link 连接环、链节Line assembly 连杆装配图Chain link 链节L-iron 角铁List 注册、记录、名册、目录Load 符合Actual load 有效载荷、实际载荷Allowable load 容许载荷Full load 满载(荷)、全负载(荷) Local view 局部视图Localization 定位\固定Locating pin 定位销Location by angle 角度定位Location by dimension 定位尺寸Location pin 定位销Location tolerance 定位公差Lock 锁\阀Lock nut 防松螺母Lock screw 锁紧螺钉Lock washer 弹簧垫圈Valve lock 阀簧抵座销、气门制销Loco 机车、火车头Logarithm 对数Long break 长断裂线Long radius 长半径Longitudinal key 长方键Lower limit 下限Lubricant pump 润滑油泵Lubricating ring 润滑油环Lubrication 润滑Bath lubrication 油浴润滑Bearing lubrication 轴承润滑Ring lubrication 油环润滑Shot lubrication 油枪润滑Splash lubrication 飞溅润滑Lubricator 润滑器Lubro-pump 油泵Luminaire 光源Machine 机器、切割Machine building (manufacturing) 机械制造Machine drawing 机械制图Machine finish 机械加工Machine maker 机械工厂(制造者) Machine part 机械零件Machine shop 机工车间Drawing machine 绘图机Tracing machine 描图机Machining allowance 加工余量Machinist 机械工人\机械师Magazine 杂志Magnetic-particle clutch 电磁离合器Magnitude 数量、长度、大小Major type of slotted nut 大型锁母Make 制造、构造Malleable cast iron 可锻铸铁Malleable casting 韧铸件Malleable steel 软钢、展性钢Manual 手册、说明书Manual control 手控Manufacture 加工、制造业Manucturing engineering 制造工艺(技术) Manucturing machine 生产机械Manucturing tolerance 制造公差Master check 校正、校对Master drawing 样图Master gauge 标准规、校准规Master gear 主齿轮、标准齿轮Master making 手工Master screw 标准螺纹Match 匹配、配合Mate 啮合部分Material 物质、材料Fibre material 纤维材料Insulating material 绝缘材料Plastic material 塑料Maximal valve 极大值Maximum 极点、极限、最大量Maximum admitted diameter of work 工件最大许可直径Mean axis 中间轴Measure 量度、大小、尺寸Measure of precision 精确度Measurement 测定、尺寸、大小Measuring device 量具Measuring tools 量具Mechanical bolt 螺钉Mechanical drawing 机械制图Mechanical engineering’s scale 机械工程比例尺Mechanical properties 机械性能Mechanical reduction gear 齿轮减速装置Mechanism 机械结构、机械装置Medium series 中系列Mating member 配合件Meshing gear 啮合齿轮Metal 金属Admiralty metal 含锡黄铜Bell metal 青铜合金、种铜、铜锡合金Brazing metal 铜锌合金Hard metal 硬质合金Heavy metal 重金属Light metal 轻金属Monel metal 铜镍合金Power(ed) metal 粉末合金Wear-resistant metal 耐磨金属White metal 白合金(铅锑锡合金)Yellow metal 黄金、黄色金属Metallized 镀金属的、喷涂金属的Meter 米、公尺。
图纸常见英文词汇
一、MATERIAL（材料）
英文
Electro-galvanized steel(SECC)
Cold roll steel(CRS) halfhard copper Silicon steel stainless steel metal alloy nickel plating degrease spray paint silk screen chroma rustiness grey dimension third angle projection size cross section front view oval hole insertion of bending part number lance form opposite side screw punch chamfer diameter width burr side corner biconvex radius an angle of ninety file screw rivet wiredrawing sample accompanied unless conform fine direction otherwise produce sharp opening
中文 不锈钢片 黄铜 垫圈 螺丝刀 螺丝攻 孔径规 螺帽
电光锡亚锡 氧化银白色 磨砂 金黄色 氧化 建议尺寸 铬
二、FINISH（表面处理） zinc plating 镀锌 black anodize 氧化黑色 sand blasting 喷砂 coating 涂层 electrolysis 电解 see note 注意看 grain direction 磨纹方向 三、SEE DRAWING（视图） 尺寸 angles 角度 第三角视图 scale 比例 规格 detail 祥图 剖面视图 left side view 左视图 主视图 hole 孔 椭圆孔 burring 猪嘴孔 脚仔 bending 折边 货号 revision/issue 版本 桥位 near 正面 相对面 thread 螺纹 螺钉 extrusion 挤形 冲裁 welding 焊接 斜角 radius 圆角 直径 length 长度 宽度 deep 深度 披风面 rolling(grain)direction 料纹方向 角 bend 弯曲 两面凸 point 点 半径 diameter 直径 90度角 base 底 挫 nail 钉 螺丝钉 nut 螺母 铆钉 staple U U型钉 拉丝 debugging 调试 样品 report 报告 附带 deliver 交付 除….之外 surface 表面 符合 grade 等级 优良 brush 轻擦 命令 cohversion 变换 别样的 further 进一步 制造 computer 计算器 锋利 deges 边界 孔、口 emboss/convex 凸形
图纸常用英语模板
复合剖视compound section剖面图section, sectional view重合剖面coincide section, revolved section移出剖面removed section剖面线section line剖面符号symbols for section-lining习惯画法conventional drawing局部放大图 drawing of partial enlargement零件图detail drawing, working drawing第三角投影third angle projection粗实线continuous thick line, full line, visible line细实线continuous thin line虚线dot line, dashed line, hidden line点划线dash and dot line双点划线double dots line波浪线断裂线break line剖切平面迹线cutting plane line尺寸线dimension line尺寸界线extension tine尺寸dimension size箭头arrowhead基准datum基准线datum line基准面datum plane中心孔central hole中心距center distance轴shaft, axle孔hole斜孔inclination装配图assembly drawing性能尺寸characteristic dimension大小尺寸size dimension总体尺寸外形尺寸outer dimension配合尺寸fit dimension内圆角fillet外圆角round尖角sharp corner倒角chamfer轮缘flange of wheel缘、边、环rim轴肩shoulder凸台boss凹坑concave pit 轴颈shaft neck轮毂hub轮辐spoke, spoke of wheel直纹滚花straight knurling s网纹滚花hatching knurling键槽key-way退刀槽escape拔模斜度pattern draft填料盒gland box油槽oil groove油封oil seal标准件standard parts螺纹thread外螺纹external thread内螺纹internal thread大径major diameter小径minor diameter螺距pitch of thread牙型form of thread旋向direction of turning右旋螺纹right-hand thread左旋螺纹left-hand thread头数number of thread导程lead粗牙coarse thread细牙fin thread螺栓bolt螺钉screw螺柱stud螺母nut垫片washer公差tolerance公差带tolerance zone零线zero line标准公差standard tolerance公差等级tolerance grade基本偏差fundamental deviation配合fit间隙配合clearance fit过盈interference过盈配合interference fit过渡配合transition fit基孔制hole-basic system of fits基轴制shaft-basic system of fits间隙clearance形状公差tolerance in form, form tolerance直线度straightness平面度flatness圆度roundness圆柱度cylindricity线轮廓度pro any line面轮廓度pro any plane位置公差tolerance in position, position tolerances平行度 parallelism齿轮gear圆柱齿轮cylindrical gear正齿轮spur gear斜齿轮spiral gear轮齿gear tooth节圆pitch circle齿顶圆addendum circle, outside circle齿根圆root circle, addendum circle模数modulus齿数number of teeth齿高tooth height齿顶高height of addendum齿根高height of addendum齿厚circular thickness齿间tooth space齿宽tooth width压力角angle of pressure弹簧spring销pin圆柱销round pin圆锥销taper pin开口销cotter pin, split键key平键flat key半圆键half round key, woodruff key轴承bearing滚动轴承rolling bearing向心铀承radial bearing密封装置sealing equipment锁紧装置locking equipment粗糙度roughness基本尺寸basic size实际尺寸actual size极限尺寸limits size最大极限尺寸maximum limit of size最小极限尺寸minimum limit of size偏差deviation 上偏差upper deviation下偏差lower deviation垂直度perpendicularity倾斜度angularity同轴度concentricity对称度symmetry位置度true position跳动run-out圆跳动cycle run-out全跳动total run-out轴测投影axonometric projection轴测投影面plane of axonometric projection 轴测图axonometric drawing正等轴测投影isometric projection正二测bimetric projection斜二测oblique bimetric projection轴测轴axonometric axis轴间角axis angle, angle between ales缩短foreshortened轴向缩短率coefficient of axial deformation ratio offore shortening for any axis切割法cutting method, by cutting方箱法boxing method坐标法coordinate method方框法enclosing-square method四心近似法four-center approximate method机械工程图中常用的英语词汇Abbreviation 缩写Accuracy 精度、准确性Acme thread 梯形螺纹(29°)Addendum 齿顶高Addendum angle 齿顶角Addendum circle 齿顶圆Addendum of mating gear 啮合齿轮的齿顶高Adjacent-part lines 相邻零件线Aligned sections 旋转剖视Aligned view旋转视图Allowance 容差、加工余量Alloy 合金Alloy steel 合金钢Alphabet 字母Alteration 变更、更改Alternate-position views 位置改变的视图Alternator 交流发电机Induction alternator 感应(交流)发电机Motor alternator 电动(交流)发电机Single-phase alternator 单向(交流)发电机Synchronous alternator 同步(交流)发电机Three-phase alternator 三相(交流)发电机Amount 总量、总计Analyzable assembly 分析装配图Anchor bolt 地脚螺栓Angles 角Acute angle 锐角Blunt angle 钝角Right angle 直角Sliding angle 摩擦角Spiral angle 螺旋角Taper angle 锥角Angular 有角的Angular bearing 径向止推轴承Angular bevel gears 斜交伞齿轮Angular gear人字齿轮Angular section斜剖面Anneal 退火Approval 批准、许可Arc 弧、圆弧Arc thickness 弧长厚度(齿厚)Arc welding 弧焊Arrangement 布置、装置Arrangement of views 视图的布置Clamping arrangement 夹紧装置Cramping arrangement 紧固装置General arrangement 总体布置Arrow 箭头Arrowheads 箭头Assembly 装配图、组装图Assembly drawing 装配图Assembly drawing number 装配图图号 Assembly for installation 安装图Assembly parts 组装配合零件Assembly sections 装配图剖视Assembly sketches 装配草图Auxiliary elevation 辅助立面图Auxiliary line辅助线Auxiliary section 辅助剖视Auxiliary surface 辅助面Auxiliary view 辅助视图Average 平均数Axial 轴的、轴向的Axial pitch 轴向节距Axial plane 轴向平面Axial thickness 轴向厚度Axis 轴线、中心线Axis of revolution 回转轴线Axis of rotation 旋转轴线Axis of symmetry 对称轴线Horizontal axis 水平轴Major axis 长轴Minor axis 短轴Vertical axis 垂直轴X axis X轴Y axis Y轴Axle 轴Axle bearing 轴向(止推)轴承Axle sleeve 轴向(止推)套筒Axonometric drawing 轴测图Babbitt 巴氏合金Back cone 背锥Back cone radius 背锥半径Back elevation 后视图Backstop 托架、棘爪Ball bearing 球轴承Bar 杆Angle bar 角钢Channel bar 槽钢Flat bar 扁钢Round bar 圆棒、圆钢Base 基础、底座、基线、基面、基准Base circle 基圆Base circular thickness 基圆弧线齿厚Base cylinder 基圆柱Base helix angle 基圆上的螺旋角Base plane 基平面Base point 基点Key base 键座Basic circle 基准圆Basic hole system 基孔制Base shaft system 基轴制Basic size 基本尺寸、公称尺寸、标称直径Basis 基础、基准、基线Battery 电池、蓄电池Bearing 轴承、支撑、方位Bearing accuracy 定位精度Bearing box 轴承箱Bearing brass 铜轴衬Bearing bridge 轴承支架Bearing oil seal 轴承油封圈Bearing support 轴承架Bearing unit 轴承组合件Anti-friction bearing 减摩轴承Ball and socket bearing 球窝轴承Conical bearing 锥形轴承Journal bearing 径向轴承Needle bearing 滚针轴承Plain bearing 滑动轴承Roller bearing 滚柱轴承Self-aligning bearing 自位轴承Thrust bearing 止推轴承Belt 带、皮带Bench 工作台Work bench 工作台Bend 弯头、接头Elbow bend 肘形弯管Normal bend 正弯管(90°)Bender 弯曲机Bending 挠曲Bending strength 抗弯强度Bent axle 曲轴Bevel 倾斜的、斜角的、斜面Bevel gear 圆锥齿轮、伞齿轮Bevel pinion 小圆锥齿轮Bevel washer 斜垫圈Bevel wheel 伞齿轮、斜摩擦齿轮Bilateral tolerance 双向公差Bill of materials 送料单Block in、block out 画草图Blue paper 蓝晒纸Blueprint 蓝图、设计图Board 板、(管理)局、厅Bottom board 底板Moulding board 模板Body 机体、机身Boiler 锅炉Bolt 螺栓、插销Adjusting bolt 调整螺栓Assembling bolt 装配螺栓Binding bolt 连接螺栓Bright blot 光制螺栓Captive bolt 固定螺栓Double-screw bolt 双头螺栓Fitter bolt 装配螺栓Foundation bolt 地脚螺栓Hexagonal head bolt 六角头螺栓Hook bolt 钩形螺栓Screw bolt 全螺纹螺栓Snap bolt 圆头螺栓Tension bolt 拉紧螺栓Bolted joints 螺栓连接Book 书、册Hand book 手册Instruction book 说明书Bore face machine 镗孔端面加工机床Borer 镗床Jig borer 坐标镗床Table borer 台式镗床Boring 镗孔Boring machine 镗床Boring mill 镗床Bottom case 底座Bottom clearance 径向间隙Bottom view 底视图Bracket 托架、支柱Brake 制动器、闸Brass 黄铜、铜轴衬Braze 铜焊Brazing 铜焊Breadth 宽度、厚度Break line 断裂线Brinell figure (number) 布氏硬度Brinell hardness 布氏硬度Broacher 拉床、绞孔机Broaching 扩孔机、拉床、拉削Broken circle 虚线圆Broken out section 断裂剖面Broken view 局部视图Bronze 青铜Burnishing 抛光、磨光Burr 三角矬、毛刺、去毛刺Bush 衬套、轴瓦Bushing 轴衬、衬套、套管Butt joint 对接焊Butterfly nut 蝶形螺母Butterfly valve 蝶形阀Button 按钮Push button 控制按钮Cable 电缆Cage 盒、罩、箱Caliper 卡尺、卡钳Gauge caliper 卡规、量规Internal caliper 内卡钳Sliding (vernier) caliper 游标卡尺Cam 凸轮Cam design 凸轮设计Cam shaft 凸轮轴Actuating cam 主动凸轮Adjustable cam 可调凸轮Control cam 控制凸轮Cap 盖、帽、罩Cap screw 带帽螺钉Capital 大写字母Carburizing 渗碳Card 卡片Cartographer 制图员Cartography 制图学、制图法Case 箱、盒、容器、表面Case hardened 表面淬火、硬化 Nitrogen case hardening 渗氮硬化 Casing箱、盒、壳Oil pump casing 油泵(壳)Casting 铸造、铸件Defect casting 铸件缺陷Die casting 压铸Sand casting 砂型铸造Spun casting 离心铸造Steel casting 铸钢Cast-iron 铸铁Castle circular nut 六角圆螺母Castle nut 蝶形螺母Catalogue data 表列数据Cave 凹槽、内腔Centre 中心、圆心Centre distance 中心距Centre hole 中心孔Centre line 中心线Centre-section 中心剖面Centre to centre 中心距Centesimal 百分的、百分之一的Centimeter 厘米、公分Central hole 中心孔Central plane 中心平面Central projection 中心投影Chafe 摩擦、磨损Chain 链Drive chain 主动链Transmission chain 传动链Chamfer 倒角、倒棱、斜面Dimensioning of chamfer 倒角的尺寸注法Changes on drawing 图的更改Channel 沟槽Chapter 章Chart 图表、计算图Chart of symbols 符号图表Auxiliary chart 辅助图Dimensions chart 外廓尺寸图Graphical chart 图表Process chart 工艺程序图Progress chart 工艺程序表、工作进度表 Charting 制图(表)、填图Check 校验、校核、制动装置Check drawings 校图Check nut 防松螺母Check ring 挡圈Check test校核试验Chief draftsman 主任制图员Chromium 铬Chromizing 镀铬处理Circle 圆、圆周Circle of reference 参考圆Addendum circle 齿顶圆Base circle 基圆Graduated circle 分度圆Imaginary circle 虚圆Outside circle 齿顶圆、外圆Pitch circle 节圆Rack circle 平面齿轮、扇形齿轮Root circle 根圆Top circle齿顶圆Circular cylinder 圆柱Circular pitch 弧线节距Circular thickness 弧线(齿)厚度Circumference 圆周长Clamp 夹紧、夹板Class 种类Class of fit 配合级别Classification 分类Claw 爪、钩、卡爪Clearance fit 间隙配合Clevice /clevis U形钩、U形夹Clevis bolt 套环(插销)螺栓Clevis pin U形夹销Clockwise 顺时针方向Clutch 离合器、联轴器Coat 外层、涂镀层Coat of metal 金属镀层First coat 底漆Coating 镀、覆盖Electrodeposited coating 电镀层Coaxial circle 共轴圆Cock 旋塞Coil 蛇形管、螺管、线圈Coil spring 盘簧Coincident line 重叠线Cold-rolled steel 冷轧钢Collet 夹头Collet chuck 弹簧夹头Color-harden 着色硬化、发蓝、煮黑Common difference 公差Company 公司 Joint company 股份公司Limited company 有限公司Compass 圆规Compass of proportion 比例规Component 零件、构件Compression spring 压力弹簧Compressor 压缩机Computer 计算机Concave face 凹面Concentricity 同心度Cone 圆锥Cones development 锥面展开Cone pulley 锥形轮、塔轮Conical spring 锥形弹簧Connection 联接Bolt-on connection 螺栓联接Flange connection 法兰联接Rivet connection 铆钉联接Screw connection 螺钉联接Contact 接触、接合、啮合Contact angle 啮合角Angular contact ball bearing 向心止推球轴承Contour 外形、轮廓线Contracted drawing 缩图Contrast 对比、对照、比较Convention 惯例、常规、习惯Convention for materials 材料的习惯表示法 Conventional break 习惯断裂画法Conventional diagram 习惯画法Conventional intersection 习惯交线(画法) Conventional practice 习惯画法Conventional sign 图例、习惯符号|Convex 凸面Conveyer 输送机、传送机Cooler 冷冻机Coordinate axis 坐标轴Coordinate paper 方格纸、坐标纸Copper 铜Copy 抄本、样板Correction 校正、修正Cotter pin 开口销Split cotter 开口销Counterbore 埋头孔、锥口孔Counterclockwise 逆时针方向Countersink 埋头孔、沉孔Countersink drill 中心钻、钻Countersunk 钻埋头孔、钻锥口孔Countersunk bolt 埋头螺钉Countersunk head 埋头Countersunk hole 锥坑Coupling 联轴节Cover 盖、罩Cylinder cover 汽缸盖Dust cover 防尘罩Cowl 壳、套、盖Crane 起重机Crank 曲柄、曲轴Crankshaft 曲轴Crest 峰、尖、牙尖Cross head 十字头Cross section 横剖面、横断面Crown gear 冕状齿轮Cube 立方形体、正六面体Current 电流Curvature 曲率Curvature radius 曲率半径Curve 弯曲、曲线、曲线板Curve plotter 绘图仪Curve ruler 曲线板French curve 曲线板Moment curve 力矩曲线、力矩图Cutter 刀、刀具Cutting plane 截平面Cutting plane symbols 剖切(迹线)平面符号Cycloid 摆线Cycloidal gear 摆线齿轮Cylinder 圆柱体Cylinder base 汽缸座Pump cylinder 泵缸Cylindrical cam 圆柱凸轮Cylindrical fit 圆柱配合Cylindrical roller bearing 圆柱滚子轴承Dash 短划线、虚线、破折号Dash and dot line 点划线Broken dash 断裂线Data 数据、资料Engineering data工程数据Master data 主要数据Date 日期、年代Datum 基准(点、线、面)、资料Datum line 基准线Datum point 基准点 Datum plane 基准面Decade 十进制、十进位Decelerator 减速器、制动器、缓动装置Decimal 小数的、十进位小数的Decimal fraction 十进制分数Decimal fraction system 十进小数制Decimal scale 十进位比例尺Decimeter 分米、公分Dedendum angle 齿根角Dedendum circle 齿根圆Definition 定义Deformation 变形、扭曲Degree 度、程度Degree of accuracy 精度Degree of freedom 自由度Degree of hardness 硬度Degree scale 刻度Circular degree 圆度Delineation 轮廓、草图Delineator 制图者Department 科、处、系、车间Draft department 设计科Engineering department 技术科Fitting department 装配车间Heat treatment department 热处理车间Mechanical department 机加工车间Processing department 工艺科Depth 深度、高度Depth dial gauge 深度千分表Depth of engagement 啮合深度Depth of thread 螺纹深度Depth of tooth 齿高Contact depth of tooth 啮合高度Working depth of tooth 齿工作高度Derivation 偏差Standard derivation 标准偏差Description 描述、作图、绘制Design 设计、计划Design activity 设计机关(组织) Design assembly 设计装配图Design drawing 设计图Design layout 设计草图、初步设计图Preliminary design 初步设计Standard design 标准设计Technical design 技术设计Designation 符号、标志Designation strip 铭牌Designer 设计员、制图者、设计师Desk 桌、控制台Drawing desk 绘图桌Detail 细目、细节、详图、零件Detail drawing 详图、零件工作图Detail paper底图纸、描图纸Detail specification 详细规格Detent 棘爪、扳手、制动器Developable surface 可展曲面Developed view 展开图Development inner port 内表面展开图Development of surface 表面展开图Deviation 偏差、偏移Angular deviation 角偏差Average deviation 平均偏差Standard deviation 标准偏差Tolerance deviation 允许偏差Device 装置、设备Diagram 示意图、图解Diagram drawing 图解图、结构图Arrangement diagram 布置图Assembly diagram 装配示意图Block diagram 方框图Schematic diagram 原理图、简图Diagrammatic drawing 草图、示意图Dial gauge 千分表Dial inside micrometer 内径千分表Diameter 直径Diameter of aperture 孔径Diameter of pitch circle 节圆直径Diameter pitch (齿轮)径节Diameter run-out径向跳动Major diameter 大直径、螺纹外径Minor diameter 小直径、螺纹内径Nominal diameter 公称直径Pitch diameter of screw thread 螺纹中径Thread diameter 螺纹外径(直径) Diametral pitch 齿轮径节Die 模具、扳牙Diesel 柴油机、内燃机Dimension 尺寸Dimension line 尺寸线Limiting dimension 极限尺寸Nominal dimension 公称尺寸Outer dimension 外形尺寸、轮廓尺寸Direction 方位、方向Clockwise direction 顺时针方向Disc = disk 圆盘、原板Disk cam 圆盘凸轮Dismount 拆卸Dismountable 可拆卸的Displacement 移位、变位Distance 距离、路程Distortion 变形、歪扭Distribution 分配、分布、配置Ditto machine 复印机Diversion 变更、转换Dividing head 分规Dot line 虚线Dotted line 虚线Double dots line 双点划线Double helical pinion 人字小齿轮Double helical spur gear 人字齿轮Double thread 双头螺柱Dowel thread 定位销、圆柱销Dozer 推土机Draft = draught (拔模)斜度、草图、制图Drafting 制图Drafting board 制图板Drafting machine 制图机Drafting tape 制图带、胶带Draftsman 绘图员Drawer 制图员Drawing 绘图、图样Drawing board 绘图纸Drawing control 图样管理Drawing free-head 草图Drawing instrument 绘图仪器Drawing number 图号Drawing pencil 绘图铅笔Drawing pin 图钉Drawing size 图纸尺寸Drawing table 制图桌Drawing with compass 用圆规画图Blue print drawing 蓝图Free hand drawing 徒手图Full size drawing 原大图Skeleton drawing 草图、结构图Working drawing 施工图、制造图、工作图Drill 钻孔、穿孔、穿孔器Drive 传动、驱动Drive fit 打入配合Air drive 气动Belt drive 带传动Chain drive 链传动Friction drive 摩擦传动Gear drive 齿轮传动Hydromatic drive 液压传动Speed-reducer drive 减速器传动Variable-speed drive 变速传动Worm-wheel drive 蜗轮传动Driven gear 从动齿轮Driven shaft 从动轴Driving gear 主动齿轮Driving shaft 主动轴Drum cam 凸轮轴Ductile iron 球墨铸铁Duplicating tracing 复制描图Durometer (钢轨)硬度计Dusting cloth 抹灰布、撒粉布Eccentricity 偏心距Edge iron 角铁Edge round 外圆角Edge view 边视图Effective diameter 有效直径Effective face width 有效齿宽Efficiency 效率、性能Mechanical efficiency 机械效率Elastic deformation 弹性变形Elasticity 弹性Elbow 肘形弯管、弯头Electric current 电流Electric element 电池Elephant 绘图纸(28X23英寸) Elevation 正面图、立视图End 末端、头Ball end 秋端Butt end 平端、端面Tail end 尾端Top end 顶端Engagement 啮合Engineer 工程技术人员、工程师Engineer-in-chief 总工程师Equipment 设备Eraser 橡皮Erasing shield 擦图片Erection diagram 安装图、装配图Error 误差Accumulated error 累积误差Allowance error 容许误差Average error 平均误差Permissible error 容许误差Relative error 相对误差Exterior 外表面External 外部External diameter 外径External dimension 外形尺寸External fillet 外圆角External thread 外螺纹Extra fine(screw)特细牙螺纹Eyelet = eyelet-hole 小孔Fabrication 建造、制造Face 面、正面、表面、端面Face cam 平面凸轮Face gear 平面齿轮Face hardening 表面硬化Inner face 里面Outer face 外面Face off 倒角Factor of safety 安全系数Factory 工厂、制造厂Factory made 工厂制造的Fastener 接合件、紧固件Fastening 连接件、紧固件Fatigue 疲劳Faucet 旋塞、龙头、开关Feather 滑键、冒口Feather key 滑键Feature 特征、特性、性能Basic mechanical design feature 主要机械设计性能Mechanical feature 机械性能(特性)Feed-pump 供油泵、供水泵Feet 英尺Ferrous metal 黑色金属Field 工场、现场Figure 形状、图样、插图、数字File 锉刀、锉平Filler 填料、垫片Fillet (内)圆角、填角、嵌条Fillet radius 内圆角半径Filter 过滤器Fine thread series 细螺纹级(系列)Finish 完工、加工、磨光Finish all over 全部加工Finish marks 加工符号Machine finish 机器光制Fit 配合Clearance fit 间隙配合Free fit 自由配合Interference fit 静配合Light press fit 轻压配合Light running fit 轻传动配合Loose fit 松配合Normal-running fit 传动配合Running fit 动配合Shrink fit 冷缩配合Slide fit 滑动配合Transition fit 过渡配合Fix 安装、装配、调整、修理、固定Flange 法兰盘、凸缘Flank 边、侧面、齿侧、后面Flat 扁头、平面Flat key 平键Flat spring 板弹簧Flat surface 平面Flexible disk coupling 挠性盘形联轴节Flexible gear-type coupling 挠性齿轮联轴节Flywheel 飞轮Foot 英尺Foot screw 地脚螺钉Force 力Fore word 序、前言Forge 锻Forge steel 锻钢Former 样板、模型、量规Wooden former 木模Formula 公式Foundation 基础、基座Foundation bolt 地脚螺栓Foundry 铸件、铸工车间Fraction 分数、小数Front view 前视图、主视图Full diameter 大直径、主直径Full line 实线Full size 原大Full scale 原大Full section 全剖视Full section view 全剖视图Furbish 研磨、擦光Fuse 保险丝、熔断器Gage = gauge 量规Gallon 加仑Galvanize 镀锌、电镀Gasket 垫圈、密封垫Gasket material 填料Gasoline engine 汽油(内燃)机Gate 门、阀门Gear 齿轮Gear addendum angle 齿顶角Gear box(case) 齿轮箱Gear centre 齿轮中心Gear dedendum angle 齿根角(圆锥齿轮) Epicyclic gear 行星齿轮Herringbone gear 人字齿轮Ratchet gear 棘轮General drawing 总图Geometry 几何学Gland 压盖、填料盖、密封装置Glass 玻璃Glasscloth 砂布、玻璃布Glossary 词汇(表)Grade 等级、斜度Steel grade 钢号Graduated hardening 分级淬火Graduated scale 比例尺、分度尺Gram 克Graph 图(表、解、形)、曲线图Graph paper 方格纸Graphic图示、制图学Grease 滑脂Grind 磨削、抛光Grinding machine 磨床Grinding wheel 砂轮Groove cam 槽凸轮Groove pulley 槽轮、三角带轮Guide 手册、指南Guide bar 导杆Guide pin 定位销、导向销Guide screw 丝杠Guidebook 参考手册、指南、入门Half 二分之一、一部分Half bearing 轴瓦Half section 半剖视Half section view 半剖视图Hammer 锤子Handbook 手册、指南Hand-made 手工制造的Hand-operated 手控的Handle 手柄Hand wheel 手轮Hard casting 白口铁Hard drawn 冷拔Hard rolled 冷轧的Hard surfacing 表面硬化Harden 淬火、硬化Hardened and tempered 调质的Hardened-steel 淬火钢Hardening 硬化Hardness 硬度Hardometer 硬度计Hatch 剖面线H-beam 工字梁、H形梁Heat–treatment 热处理Heavy force fit 重压配合Height 高度Helical bevel gear 螺旋伞齿轮Helical gear 螺旋齿轮、圆柱斜齿轮Helical rack 斜齿齿条Helical spring 螺旋弹簧Hex nut 六角螺母Hexagon jam nut 六角锁紧螺母Hexagon socket head 内六角头Hidden line 虚线Hidden outline 看不见的轮廓线High-carbon steel 高碳钢High-duty 重型的、大型的、优产的 High-speed steel 高速钢Hosting jack 千斤顶Hole 孔Horizontal datum plane 水平基准面Horizontal line 水平线Horizontal projection 水平投影Horizontal projection plane 水平投影面Horse-power 马力、功率Hose 软管Hose coupling 软管接头Hot-rolled steel 热轧钢Hot-work 热加工Hour 小时Housing 机座Housing of pump 泵体Bearing housing 轴承箱Gear housing 齿轮箱Hub 轮、中心、衬套I-beam 工字钢Illustration 插图、实例Inaccuracy 不精确、不准确Incenter 内(切圆)心Inch 英寸Incline 斜度、斜面Index plate 分度盘Indicator 指示计、百分表Industrial 工业公司Industrial drawing 工业制图Industry 工业Inertia 惯性Ink 墨水、油墨Ink holder 钢笔杆China ink 墨汁Inscription 标题Inside diameter 内径Inspection 检修、检查Inspection machine 检修机器Inspector 检查员Installation 装置、设备、安装Installation diagram 安装图Institute 研究所、协会、学院、学会Instruction 说明、指示Instrument 仪器、仪表、工具Instrument drawing 仪器图Intensity 强度Interchangeability 互换性1 Interconnection 互相连接Interference fit 静配合Interior view 内部(的)视图Internal combustion engine 内燃机Internal fillet 内圆角Internal gear 内齿轮Introduction 引言、介绍、序言Invisible line 虚线Involute 渐(伸)开线Involute gear 渐开线齿轮Involute rack 渐开线齿条Involute spline 渐开线花键Involute teeth 渐开线齿形Iron 铁Ingot iron 低碳铁、工业纯铁Knobbled iron 熟铁Magnetic iron 磁铁Malleable iron 可锻铁、韧性铁Plate iron 铁板、钢板Quadrant iron 方钢Rod iron 圆铁、棒钢Round iron 圆铁、圆钢Rustless iron 不锈铁Section iron 型钢Structural iron 结构钢White iron 白口铁Wrought iron 熟铁、锻铁Isometric diagram 等轴测图Isometric drawing 等轴测图Jack-screw 螺旋千斤顶Job sheet 零件图纸Joint 结合、连接、焊接Bolt joint 螺栓连接Riveted joint 铆钉连接Welded joint 焊接Journal 轴径Journal bearing 径向轴承Keeper 保持器(片)、架、定位件卡箍Keep-ring 保持环Key diagram 键、按钮Key way(seat、seating、slot)键槽Key wrench 套筒扳手Gib-head taper key 钩头斜键Square key 方形键Tightening key 斜扁键Woodruff key 半圆键Key-bolt 键螺栓Kilogram(me)公斤、千克Kilogram-meter 公斤米、千克米Kilometer 公里、千米Kilovolt 千瓦Kilowatt 千伏Kit 一套工具Knee 弯头、升降台Knee bend 弯管Knob 捏手、按钮Knuckle thread 圆形螺纹Knurl 滚花、压花Knurled nut滚花螺母L-bar = L-beam 角钢Laboratory 实验室、研究室Lamp 灯Alarm lamp 信号灯Daylight lamp 日光灯Incandescent lamp 白炽灯Indicating lamp 信号灯、指示灯Lantern 游环、套环Large compasses 大圆规Lathe 车床Lathe-hand 车工Lattin = Latten 金属薄板、黄铜片Law 规律、定律Lay 布置、安排、放置Layer 层Carburized layer 渗碳层Layout 计划、方案、草图Layout design 草图设计、方案设计Layout drawing 方案草图Lead angle 螺旋升角Lead line 指引线Leaf spring 板弹簧Left hand 左方向Left hand thread 左旋螺纹Legend 图例、图表符号、代号、说明书Length 长度、距离Length gauge 长度规Length of normal 法线长Length of side 边长Effective length 有效长度Lens 透镜、镜片Letter 字、字母Capital letter 大写字母Level surface 水平面Lift 升降机、电梯Light alloy 轻合金Light beam 光束Light series 轻系列Light-duty 轻型Lighting installation 照明装置Lightning switch 照明开关Liquid 液体Limit 极限尺寸Limit switch 限位开关Line 线Line of action (齿轮)压力线Line of contact (齿轮)接触线Line of shaft轴线Line of thickness 线型的粗度Line weight线的粗细程度Actual line实线Addendum line齿顶线Broken line断裂线Center line = central line中心线Continuous line实线Dash(ed) line虚线Diagonal line 对角线Imaginary line 假想线Generation line 母线Pitch line 节线Real line 实线Reference line 基准线、参考线Right line 直线Skeleton line 轮廓线Solid line 实线Straight line 直线Vertical line 垂直线Liner 衬套Bearing line 轴瓦Link 连接环、链节Line assembly 连杆装配图Chain link 链节L-iron 角铁List 注册、记录、名册、目录Load 符合Actual load 有效载荷、实际载荷Allowable load 容许载荷Full load 满载(荷)、全负载(荷) Local view 局部视图Localization 定位\固定Locating pin 定位销Location by angle 角度定位Location by dimension 定位尺寸Location pin 定位销Location tolerance 定位公差Lock 锁\阀Lock nut 防松螺母Lock screw 锁紧螺钉Lock washer 弹簧垫圈Valve lock 阀簧抵座销、气门制销Loco 机车、火车头Logarithm 对数Long break 长断裂线Long radius 长半径Longitudinal key 长方键Lower limit 下限Lubricant pump 润滑油泵Lubricating ring 润滑油环Lubrication 润滑Bath lubrication 油浴润滑Bearing lubrication 轴承润滑Ring lubrication 油环润滑Shot lubrication 油枪润滑Splash lubrication 飞溅润滑Lubricator 润滑器Lubro-pump 油泵Luminaire 光源Machine 机器、切割Machine building (manufacturing) 机械制造Machine drawing 机械制图Machine finish 机械加工Machine maker 机械工厂(制造者) Machine part 机械零件Machine shop 机工车间Drawing machine 绘图机Tracing machine 描图机Machining allowance 加工余量Machinist 机械工人\机械师Magazine 杂志Magnetic-particle clutch 电磁离合器Magnitude 数量、长度、大小Major type of slotted nut 大型锁母Make 制造、构造Malleable cast iron 可锻铸铁Malleable casting 韧铸件Malleable steel 软钢、展性钢Manual 手册、说明书Manual control 手控Manufacture 加工、制造业Manucturing engineering 制造工艺(技术) Manucturing machine 生产机械Manucturing tolerance 制造公差Master check 校正、校对Master drawing 样图Master gauge 标准规、校准规Master gear 主齿轮、标准齿轮Master making 手工Master screw 标准螺纹Match 匹配、配合Mate 啮合部分Material 物质、材料Fibre material 纤维材料Insulating material 绝缘材料Plastic material 塑料Maximal valve 极大值Maximum 极点、极限、最大量Maximum admitted diameter of work 工件最大许可直径Mean axis 中间轴Measure 量度、大小、尺寸Measure of precision 精确度Measurement 测定、尺寸、大小Measuring device 量具Measuring tools 量具Mechanical bolt 螺钉Mechanical drawing 机械制图Mechanical engineering’s scale 机械工程比例尺Mechanical properties 机械性能Mechanical reduction gear 齿轮减速装置Mechanism 机械结构、机械装置Medium series 中系列Mating member 配合件Meshing gear 啮合齿轮Metal 金属Admiralty metal 含锡黄铜Bell metal 青铜合金、种铜、铜锡合金Brazing metal 铜锌合金Hard metal 硬质合金Heavy metal 重金属Light metal 轻金属Monel metal 铜镍合金Power(ed) metal 粉末合金Wear-resistant metal 耐磨金属White metal 白合金(铅锑锡合金)Yellow metal 黄金、黄色金属Metallized 镀金属的、喷涂金属的Meter 米、公尺。
工程图常用英语
工程图常用英语Bilingual Engineering Terminology投影 projection投影中心center of projection投影面projecting plane投影线projecting line中心投影法perspective projection平行投影法parallel projection斜投影oblique projection正投影orthographic projection正投影面frontal plane of projection侧面投影面profile plane of projection投影图projection drawing三面投影图three-plane projection drawing投影轴axis of projection投影特性characteristic of projection不变性characteristic of true积聚性characteristic of concentration类似性characteristic of similarity视图view三视图three-view drawing正面frontal plane正面投影frontal projection水平面horizontal plane水平投影horizontal projection侧面profile plane侧面投影profile projection主视图frontal view俯视图top view左视图left side view后视图rear view, back view仰视图bottom view立体solid平面立体plane body曲面立体body of curved surface回转面surface of revolution棱柱prism棱锥pyramid边side顶点center vertex棱edge点point直线line straight line棱锥台truncated pyramidfrustum of pyramid重影coincidence of projection积聚concentrate变形deformation实长true length实形true shape正平线frontal line水平线horizontal line侧平线profile line一般位置直线oblique line铅垂线vertical line, frontal-profile line正垂线horizontal--profile line侧垂线frontal-horizontal line一般位置平面oblique plane相交intersection平行parallel垂直perpendicular交线intersecting line, line of intersection 交点point of intersection平行线parallel line垂直线perpendicular line交叉线skew line长度length宽度width高度height组合体complex基本几何体basic body相接built-up相交inter section相切tangent相贯penetration支架brace底板bottom board肋rib支承板bearing plate轮廓线outline, contour line底图traced drawing截平面cutting plane截交线line of section二重性dual nature平面曲线plane curve圆弧arc椭圆ellipse长轴major axis短轴minor axis双曲线hyperbola抛物线parabola圆circle圆锥顶conic apex相贯体intersecting bodies相贯线line of intersection空间曲线space curve截平面方法cutting plane method辅助面auxiliary surface辅助平面auxiliary plane最高点culminating point尺寸Size定形尺寸size dimension定位尺寸location dimension左视图right view辅助图auxiliary view局部视图partial view, broken view斜视图oblique view旋转视图revolved view, aligned view剖视图sectional view, section全剖视full section半剖视half section局部剖视图partial section, broken-out section 斜剖视图oblique section旋转剖视图aligned section阶梯剖视echelon section, offset section复合剖视compound section剖面图section, sectional view重合剖面coincide section, revolved section 移出剖面removed section剖面线section line剖面符号symbols for section-lining习惯画法conventional drawing局部放大图 drawing of partial enlargement零件图detail drawing, working drawing第三角投影third angle projection粗实线continuous thick line, full line, visible line 细实线continuous thin line虚线dot line, dashed line, hidden line点划线dash and dot line双点划线double dots line波浪线, 断裂线 break line影像线，假想线 phantom line剖切平面迹线cutting plane line尺寸线dimension line尺寸界线extension tine尺寸dimension size箭头arrowhead基准datum基准线datum line基准面datum plane中心孔central hole中心距center distance轴shaft, axle孔hole斜孔inclination装配图assembly drawing性能尺寸characteristic dimension大小尺寸size dimension总体尺寸outer dimension外形尺寸配合尺寸fit dimension内圆角fillet外圆角round尖角sharp corner倒角chamfer轮缘flange of wheel缘、边、环rim轴肩shoulder凸台boss凹坑concave pit轴颈shaft neck轮毂hub轮辐spoke, spoke of wheel直纹滚花straight knurling s网纹滚花hatching knurling键槽key-way退刀槽escape拔模斜度pattern draft填料盒gland box油槽oil groove油封oil seal标准件standard parts螺纹thread外螺纹external thread内螺纹internal thread螺距，螺纹间距 pitch大径major diameter小径minor diameter螺距pitch of thread牙型form of thread旋向direction of turning右旋螺纹right-hand thread左旋螺纹left-hand thread头数number of thread导程lead粗牙coarse thread细牙fin thread螺栓bolt螺钉screw螺柱stud螺母nut垫片washer公差tolerance公差带tolerance zone零线zero line标准公差standard tolerance公差等级tolerance grade基本偏差fundamental deviation 配合fit间隙配合clearance fit过盈interference过盈配合interference fit过渡配合transition fit基孔制hole-basic system of fits基轴制shaft-basic system of fits间隙clearance形状公差tolerance in form, form tolerance直线度straightness平面度flatness圆度roundness圆柱度cylindricity线轮廓度profile of any line面轮廓度profile of any plane位置公差tolerance in position, position tolerances 平行度 parallelism齿轮gear圆柱齿轮cylindrical gear正齿轮spur gear斜齿轮spiral gear轮齿gear tooth节圆pitch circle齿顶圆addendum circle, outside circle齿根圆root circle, addendum circle模数modulus齿数number of teeth齿高tooth height齿顶高height of addendum齿根高height of addendum齿厚circular thickness齿间tooth space齿宽tooth width压力角angle of pressure弹簧spring销pin圆柱销round pin圆锥销taper pin开口销cotter pin, split键key平键flat key半圆键half round key, woodruff key轴承bearing滚动轴承rolling bearing向心铀承radial bearing密封装置sealing equipment锁紧装置locking equipment粗糙度roughness基本尺寸basic size实际尺寸actual size极限尺寸limits size最大极限尺寸maximum limit of size最小极限尺寸minimum limit of size偏差deviation上偏差upper deviation下偏差lower deviation垂直度perpendicularity倾斜度angularity同轴度concentricity对称度symmetry位置度true position跳动run-out圆跳动cycle run-out全跳动total run-out轴测投影axonometric projection轴测投影面plane of axonometric projection 轴测图axonometric drawing正等轴测投影isometric projection正二测bimetric projection斜二测oblique bimetric projection轴测轴axonometric axis轴间角axis angle, angle between ales缩短foreshortened轴向缩短率coefficient of axial deformation ratio offore shortening for any axis切割法cutting method, by cutting方箱法boxing method坐标法coordinate method方框法enclosing-square method四心近似法four-center approximate method。
机械图纸常用词汇中英文
1标题栏英文工程图纸的右下边是标题栏（相当于我们的标题栏和部分技术要求），其中有图纸名称（TILE）、设计者（DRAWN）、审查者（CHECKED）、材料（MATERIAL）、日期（DATE）、比例（SCALE）、热处理（HEAT TREATMENT）和其它一些要求，如：1)TOLERANCES UNLESS OTHERWISE SPECIFIAL 未注公差。
2)DIMS IN mm UNLESS STATED 如不做特殊要求以毫米为单位。
3)ANGULAR TOLERANCE±1°角度公差±1°。
4)DIMS TOLERANCE±0.1未注尺寸公差±0.1。
5)SURFACE FINISH 3.2 UNLESS STATED未注粗糙度3.2。
2常见尺寸的标注及要求2.1孔（HOLE）如：（1）毛坯孔：3"DIAO+1CORE 芯子3"0+1;（2）加工孔：1"DIA1";（3）锪孔：锪孔(注C＇BORE=COUNTER BORE锪底面孔);（4）铰孔：1"/4 DIA REAM铰孔1"/4;（5）螺纹孔的标注一般要表示出螺纹的直径，每英寸牙数（螺矩）、螺纹种类、精度等级、钻深、攻深，方向等。
如：例1. 6 HOLES EQUI-SPACED ON 5"DIA (6孔均布在5圆周上（EQUI-SPACED=EQUALLY SPACED均布）DRILL 1"DIATHRO＇钻1"通孔（THRO＇=THROUGH通）C/SINK22×6DEEP 沉孔22×6例2. TAP7"/8-14UNF-3BTHRO＇攻统一标准细牙螺纹，每英寸14牙，精度等级3B级（注UNF=UNIFIED FINE THREAD美国标准细牙螺纹）1"DRILL 1"/4-20 UNC-3 THD7"/8 DEEP 4HOLES NOT BREAK THRO 钻1"孔，攻1"/4美国粗牙螺纹，每英寸20牙，攻深7"/8,4孔不准钻通（UNC=UNIFIED COARSE THREAD 美国标准粗牙螺纹）1"-14NS-2THRO攻美国固定特种螺纹M1",每英寸牙数14,精度等级为二级（注NS=NATIONAL SPECIAL THREAD:美国固定特种标准）2.2倒角（CHAMFER）例1/8×45°BEV 倒角1/8×45°（注BEV=BEVEL，斜面）1.5×45°CHAM 倒角1.5×45°(注CHAM=CHAMFER倒角)2.3方(SQUARE)例5"SQUARE5"×5"方2.4剖视（SECTION）例SECTION A-A A-A剖面2.5圆角半径例1"R R1"RADIUS MUST BE SMOOTH AND BLEND INTO FACE圆弧必须光滑且与平面相切2.6加工余量例DOTTED LINES INDICATED MAX FINISH 1"/8虚线表示最大加工余量1"/82.7零件标记例USE 5"/16 RAISED HAIRLINE LET-TERS MARKING ON ONE SIDE OF BODY用突起高为5"/16的细实线字母在本体一侧打标记3关于铸锻件的技术要求例1. FORGING MUST BE ANNEALED TO BE BELOW 203 BRINELL HARDNESS 锻件必须退火处理，布氏硬度<203 例2. NORMALIZE TO 163-207BHN MUST BE FREE OF SCALE & RUST 锻件正火处理，布氏硬度163-207,锻件表面不得有氧化皮和锈蚀例3. FORGING TO BE SHOT OR SAND BLASTED锻件需经喷丸或喷砂处理例4. UNLESS OTHERWISE SPECIFIED DRAFT ANGLES7°未注明锻造拔模斜度7°例5. CAST TO BE FREE OF EXCESSIVE FLASH 铸件不得有过多的毛边例6. DRAFT ANGLE 2° UNLESS OTHER-WISE SPECIFIED 未注明铸造拔模斜度2°缩写 abbreviation美英加陆军规格 ABC-Army-STD美英加海军规格 ABC-Navy-STD消字膏 abrasive paste方向突变 abrupt change in direction横坐标 abscissa绝对尺寸 absolute size交流电动机控制器 AC motor controller交流电 AC(a-c，alernating current)附件 accessory累积公差 accumulated tolerance精度，准确度 accuracy准确线 accurate line透明绘图胶片 acetate梯形(爱克姆) Acme[screw]对角视图 across corner view对角 across corners对边 across flats对边视图 across flats view横断木纹 across grain of wood实际距离 actual distance实际书法 actual drawing实际配合 actual fit实际内径 actual inside diameter实际量度 actual measurement图面尺寸 actual measurement on the drawing实际分度区域，实际精确区域 actual minute area 实际零件 actual part实际位置 actual position实际尺寸 actual size锐角 acute angle齿冠 addeneum齿冠图 addeneum circle齿冠距离 addeneum distance齿冠线 addeneum line相加 adding增列数据 additional data增列资料 additional information增列位置公差 additional position tolerance增列公差 additional tolerance胶带 adhesive tape邻角 adjacent angle邻近区域 adjacent area邻接组件 adjacent component邻棱 adjacent edge邻线 adjacent line邻接地图 adjacent map邻接件 adjacent part邻接件线 adjacent parts line邻边 adjacent side相邻视图 adjacent view自由曲线规 adjustable curve活动丁字尺 adjustable head T-square调整点 adjustable point自由曲线规 adjustable ruler可调三角规 adjustable set wquare广告面 advertising illustration色透规，浓淡远近法 aerial perspective航空照相 aerial photograph航空图 aeronautical chart航测图 aeronautical map美学 aestetics逆理(木) against the grain喷刷 air brush飞机接线图 air craft wiring diagram空线，电路 airline，base line备接线 ajoining line铝 AL(aluminum)对齐尺寸线 aligned dimension lines对齐制注尺寸法 aligned dimensioning转正剖面 aligned section对齐制 aligned system转正的视图，对正的视图 aligned view对准 alignment列线图 alignment chart列线图 alignment diagram鳄齿连接器 alligator connector"裕度 ALLOW(allowance)"容许蚗?" allowable bearing容许僆q allowable variation裕度 allowance纵剖木纹 along grain of wood线的规格 alphabet of lines字母顺序 alphabetice order字母 alphabets更改后尺寸 altered dimension对错角 alternate angle交变剖面线 alternate crosshatching螺纹正规符号书法(美式) alternate light and heavy line method变换法 alternate method变换位置 alternate position变换位置线 alternate position line变换位置视图 alternate position view共轭弓形 alternate segment外错角 alternate-exterior angle内错角 alternate-interior angle交互排列 alternately spaced交流电 alternating current更改 alternation侧视图的变换位置 alternative position for side view高度 altitude铝 aluminum铝合金 aluminum alloy美国标准 AMER STD(Am Std，American Standard)美国压力管规号码 American code for pressure piping美国书法(第三角法) American method美国标准螺纹 American National screw thread美国国家标准协会 American National Standard Institute(ANSI)美国国家标准 American National Standard(ANS)美国制投影(第三角投影) American projection美国标准螺纹配合等级 American screwthread class美国机械工程学会 American Society of Mechanical Engineers(ASME)美国标准学会 American Standard Association字格板 Ames instrument字格板 Ames lettering instrument布朗沙普线规 Ametican Wire Gage，Brown & Sharpe Gage 安倍计(电) ammeter变量图表 amount of change chart面角量 amount of divergence放大电路 amplifier circuit分析 analysis分析图表 analytical chart分析线图 analytical diagram分析图 analytical graph锚，固定器 anchor固定螺栓 anchor bolt固定板 anchor plate固定螺椿 anchor stud角 angle极向角 angle角度规 angle agage中心角 angle at the center角的测量 angle measure弦角 angle of chord圆周角 angle of circumference倾角 angle of dip俯角 angle of elevation倾斜角 angle of inclination投射角 angle of projection倾角 angle of slope视角 angle of vision螺纹理论深度 angular depth of thread角尺寸 angular dimension角度定位法 angular dimensioning角度定位制 angular dimensioning system成角透视，斜透视 angular perspective角度关系 angular relationship角范围 angular space单斜面 angular surface角公差 angular tolerance角度转换 angular transformation折角管，角管 angular tube倾斜度 angularity不等角图 anisometric drawing退火 annealing注解 annotation环状公差域 annular tolerance zone圆环 annular torus环状带 annular zone圆环 annulus阳极 anode美国标准正规符号(螺纹) ANSI regular symbol美国标准简化符号(螺纹)南极圈antarctic circle天线antenna反时针方向anticlockwise视图上的交点 apparent intersection核准 APPD(approved)装饰性笔划 appendge附录 appendix附录表 appendix table承招图，核准图样 approved plan校核者，核准者 approving authority齿形近似书法 approximate circlearc method近似曲线 approximate curve八圆心近似椭圆 approximate eightcentered ellipse 四圆心近似椭圆 approximate fourcentered ellipse 近似长度 approximate length近似值 approximation护裙 apron阿拉伯数字 Arabic numerals假定标度 arbitrarv scale任意直线 arbitrary line假定原点 arbitrary origin心轴 arbor圆弧 arc弧心 arc center弧长 arc length弧线 arc line电弧熔接 arc weding拱 arch阿基米得曲线 Archimedean curve阿基米得蜗线 Archimedean spirall建筑师 architect建筑模板 architect guide template建筑图字体 architect lettering建筑学 architectonics建筑师用比例尺 architect's scale建筑布局 architectural composition建筑制图员 architectural draftsman建筑图 architectural drawing建筑草图 architectural freehand drawing建筑透视图 architectural perspective建筑计书 architectural plan建筑示意图 architectural presentation drawing建筑工 architectural work建筑学 architecture建筑制图 architecture drawing圆弧规 arcograph北极圆 arctic circle面积，区域 area面积条图 area bar chart面积图 area chart面积图 area diagram面积图 area graph算术分度图 arithmetic graph算术标度 arithmetic scale算术平均(数) arithmetical average算术分度水平坐标 arithmetical horizontal scale算术内插法 arithmetical interpolation阿肯萨斯磨石 Arkansas knife piece臂 arm角之一边 arm of angle电枢 armature电枢槽 armature slot(美国)陆海军用标准零件 Army-Navy standard parts排列 ARR(arrange)布局，配置，装置 arrangement视图的排列 arrangement of views配置图 arrangement plan箭头边，箭头所指的一面(熔接) arrow side加注箭头 arrowed[head]不用箭头注尺寸 arrowless dimensioning附箭头的线 arrowline特软橡皮 artgum美国标准的配合种类 ASA fits美国标准符号 ASA svmbol美国标准螺纹符号 ASA thread symbol美国标准学会 ASA(American Standard Association)石棉 asbesto出头部分(字母) ascender美国机械工程学会锅炉法规 ASME boiler code美国机械工程学会 ASME(American Society of Mechanical Engineers) 非球面 aspheric surface汇集数据 assemble all data装妥零件 assembled parts组合，装配 assembling装配螺栓 assembling bolt装配程序图 assembling process chart组合，装配，总成(组合件) assembly装配表 assembly chart组合图，装配图 assembly drawing组合剖面 assembly drawing number组合图，装配图 assembly print组合剖面 assembly section组合图，装配图 assembly sheet组合草图，装配草图 assembly sketch组合工作图 assembly working drawing假定原点 assumed origin组合，装配，总成(组合件) ASSY(assembly) 非对称形体 asymmetrical feature不对称 asymmetry渐近线 asymptote渐近曲线 asymptotic curve附件 attachment自动 AUTO(automatic)自动绘图机 automated drafting正图纸(晒图) autopositive paper辅助 AUX(auxiliary)辅锥 auxiliary cone辅助割面 auxiliary cutting plane辅助割面 auxiliary cutting surface参考尺寸 auxiliary dimension前辅助视图，立面辅助视图 auxiliary elevation 辅助图 auxiliary figure辅线 auxiliary line辅助俯视图 auxiliary plan辅助投影面 auxiliary plane辅助投影面 auxiliary plane of projection辅助位置 auxiliary position辅助投影 auxiliary projection辅助刻度 auxiliary scale辅助面 auxiliary surface辅助视图 auxiliary view复辅助视图 auxiliary-adjacent auxiliary view可用范围 available space平均曲率 average curavature平均偏差 average deviation平均直径 average diameter避免区域 avoid zone美国线规 AWG(Awg，American Wire Gage，Brown &Sharpe Gage) 轴角 axial angle轴线的平面 axial plane摆T，轴向偏转 axial runout轴向剖面 axial section轴线 axis横坐标轴 axis of abscissa锥轴 axis of cone纵坐标轴 axis of ordinate旋转轴线 axis of revolution旋转轴线 axis of rotation对称轴 axis of symmetry视轴 axis of vision不等角模板 axolipse template立体正投影图 axonometric drawing立体正投影图 axonometric projection立体正投影草图 axonometric sketching组合，装配，总成(组合件) AY(assembly)方位角，方位，地平经度 azimuth方位等距图表 azimuthat equidistant chart布朗沙普线规 B & S gage (Brown & Sharpe gage)韦氏细螺纹 B S F thread(British Standard Fine thread)巴氏合金 BAB(bab，Babbit)背圆锥 back cone背圆锥角 back cone angle后视图 back elevation后视图 back view背后熔接 back weld电木 backelite字母间的空白 background area后倾角 backward inclination滚珠轴承 ball bearing件号圆圈 balloon加注件号圆圈 ballooning轻木 balsa wood条形图表 bar chart条形图表 bar graph滚筒磨光 barrel finishing巴斯键 Barth key底，底边，底面 base底角 base angle基圆 base circle底面边视图 base edge底面 base face底边，基线，根线(螺纹)，空线(电路)，底线(字法) base line 锥底 base of cone基面 base plane基极(电)，底座剖面 base section基面 base surface木线(电)，基线 baseline基线注尺寸法 base-line dimensioning地下室平面图 basement plan基准角度法(圆锥度公差) basic angle method基准角度公差制 basic angle tolerancing system基本计算尺寸 basic calculate size基础图表 basic chart理想余隙 basic clearance原色 basic color基本数据 basic data基本设计 basic design基准直径法 basic diameter method理想尺寸 basic dimension图学逻辑 basic drawing logic螺纹基本形式 basic form of thread基孔制 basic hole system基本数据 basic information基线注尺寸法 basic line螺纹基本基本大径 basic major diameter基轴制 basic shaft system基本尺寸，理想尺寸 basic size基准锥度法(锥度公差) basic taper method螺纹基本形式 basic thread form基本公差 basic tolerance熔接基本符号 basic weld symbol海图 bathymetric chart歪图 batter滚球轴承 BB(ball bearing)中心距离 BC(between centers)孔位圆 BC(bolt circle)灯塔，标志 beacon联珠熔接 bead weld梁规 beam compass方位，方向，轴承 bearing方位及坡度 bearing and slope方位角 bearing angle承板 bearing plate承面 bearing surface插承接合 bell-and-spigot joint弯头 bend弯曲裕度 bend allowance折线，弯曲线，转向线 bend line曲板 bend plate弯曲半径 bend radius弯曲离隙 bend relief弯折图 bending diagram曲架 bent曲板 bent plate中心距离 between center斜角，切角，斜齿轮，斜轮 bevel斜角面 bevel face斜齿轮 bevel gear测角仪 bevel protractor测口熔接 bevel weld斜棱 beveld edge伯明翰规 BG(Birmingham centers)勃氏硬度 Bhn(BH，Brinell hardness) 双凸面 biconvex双向公差制 bilateral system of limits 双向公差 bilateral tolerance双向公差制 bilateral tolerance system 材料单 bill of material定位头 binding head鸟瞰图 bird's eye perspective鸟瞰图 bird's eye view鸟瞰图 aerial view伯明翰线号规 Birmingham wire gage 平分 bisect平分线 bisector基线 BL(base line)黑墨水 black indian ink黑白图 black-and white graph黑白图 black-and-white chart黑白图 black-and-white diagram黑白复印 black-and-white reproduction 涂黑 blackened -in黑色发蓝 blackening黑体字 blackface letter黑线图 black-line print铅笔浓度，黑度 blackness鸭嘴笔叶片 blade of pen鸭嘴笔 blade ruling pen空白区域 blank area空白范围 blank space未贯穿的孔，盲孔 blind hole未贯穿的贯穿螺孔，盲螺孔 blind tapped hole 方块图 block chart方块图 block diagram方块型 block form大楷字体 block letter布图 block out配置图 block plan附加表 block supplementary吸墨纸 blotter吸墨纸 blotting paper蓝图 blue print晒蓝图器 blue print apparatus晒图纸 blue print paper晒图 blue printing晒图机 blue printing machine发蓝 blueing蓝图分析 blueprint analysis识图，读图 blueprint reading钝角 blunt angle体对角线 body diagonal体炉管 boiler tube浓，黑，粗 bold圆点 bold dot粗线 bold line黑体数字 bold type figure黑体字 boldface letter螺栓 bolt孔位圆 bolt circle外螺纹 bolt thread圆心片 bone center加偿公差 bonus tolerance边框 border line大鸭嘴笔，边框，鸭嘴笔 border pen搪孔 bore 镗孔搪孔 boring 镗孔搪床 boring mill 镗床凸面(圆柱形凸起) boss墨水瓶座 bottleholder数字底线 bottom edge of digit字母底线 bottom edge of letter底面 bottom surface三攻螺丝攻 bottom tap仰视图 bottom view三攻螺丝攻 bottoming tap边界，边框 boundary主要尺寸 boundary dimensions 要项 boundary element边界线 boundary line边界面 boundary surface外缘线，边线 bounding line弹簧圆规，小圆规 bow compass 弹簧分规，小分规 bow divider 弹簧圆规或分规 bow instrument。
(完整版)英文机械图纸
1 标题栏英文工程图纸的右下边是标题栏（相当于我们的标题栏和部分技术要求），其中有图纸名称（TILE）、设计者（DRAWN）、审查者（CHECKED）、材料（MATERIAL）、日期（DATE）、比例（SCAL E）、热处理（HEAT TREATMENT）版本号(REVISION缩写REV) 工程变更号:E.C.N 页码(SHEET) 技术要求(NOTES）图号(DRAWING NO/P ART NO.）和其它一些技术要求，如：1)TOLERANCES UNLESS OTHERWISE SPECIFIAL 未注公差。
2)DIMS IN mm UNLESS STATED 如不做特殊要求以毫米为单位。
3)ANGULAR TOLERANCE±1° 角度公差±1°。
4)DIMS TOLERANCE±0.1 未注尺寸公差±0.1。
5)SURFACE FINISH 3.2 UNLESS STATED 未注粗糙度3.2。
not specified surface roughness is ra 6.3my 没有指定的表面粗糙度Ra 6.3 my6)40 REF 尺寸为40，参考值7）410 OPENING REF 410 开口参考尺寸8）2.5” BSP 2.5”圆锥管螺纹9）TYP 2 POSNS 2处10）OD 1/4’ outside dimension 1/4’的缩写外径值1/4’---应该为:外径值1/4”11）ALL UNSPECIFED PADI-R3 未注圆角R312）TYP CAST RADLL R9.7 未注铸造R9.713）REMOVE ALL BURRS AND SHARP EDGES 棱角倒钝14)STAMP 1/4 LETTERS DWG DT14331 PO刻1/4字图号定单号15)alternative astm b763 c99500 翻译替代材质 b763 c995 0016)UNLESS OTERWISE SPECIFIED 除非指定的17)LEADED RED BRASS:UNS C83600 TO ASTM B584，ALTERMATIV E,ASTM B763，C99500 含铅红黄铜:牌号号,B584 C83600 ASTM,也可以用此片号替代,ASTM,C99500 B763 18)no marking 没有标记19)2.5" BSPT HEXAGON 2.5” 六角圆锥管螺纹(即对丝)20)CHAMFERS NOT DIM 未注倒角21)not specified pattern draft 没有指定拔模22)all sharp edges and burrs are to be removed 清除所有的锐边和毛刺 23)measunng is in mm 测量单位为毫米MM 24）1.Dimensional tolerances unless otherwise specifie d:One Place------------------+-0.5Two place------------------+-0.30Angles----------------------+-1.0度1..除特别说明外，尺寸公差应小于：１级－－－－－－－－±０.５２级－－－－－－－－±０.３角度－－－－－－－－１°25）2. Casting tolerances apply to the location of cast outline featureslocated with basic dimensions２.铸造公差适用于具有基准尺寸的铸件轮廓特征区域；26）3．Casting to be free from oil,grit,dirt and loose particles. ３.铸件（表面）须经除油、除尘、除锈和喷砂处理；27）4．Porosity holes to be max 2.3 diameter by 1.6 dee p.４.砂眼孔最大不能超过直径2.3，深度1.6；28）5. casting quality to conform with general motors s tandards and specifications.５.铸件的质量应符合通用汽车（GM）的标准和技术说明书；29）6. Casting tolerances are not cumulative.６.铸件误差不累积； 30）7.casting tolerances unless oth erwise specified:0.0 to 75.0 ------------------------------- +-0.7575.0 to 200.0 ---------------------------- +-1.15draft angles ------------------------------2度fillet radii --------------------------------3.0corner radii ------------------------------3.0all walls & ribs ------------------------- 4.57.无特殊说明时，铸造公差应小于：０.０～７５.０－－－－－－±０.７５７５.０～２００.０－－－－±１.１５拔模角度－－－－－－－－－２°内圆角半径－－－－－－－－３外圆角半径－－－－－－－－３所有壁板和筋厚－－－－－－４.５31）8.Material cast iron per GM274M grade 2058.材料：铸铁依照GM274M 等级 205；32）9.restricted and reportable substances for parts pe r GMW 30599.零件中的限制物质和必须明示的物质（环保要求）依照标准G MW 3059;33）10.Must comply with QP-I.6-009 for production and Q P-I.6-004 for Prototypes.10.必须依照QP-6.I-009产品和QP-I.6-004原型生产34）Machining allowance to be adopted when turning a su rface to be ground is equal to Max value for required dimen sion with 0.05 mm deviation表达的是加工后基本尺寸的上下偏差，就是±0.0534）METARIAL : ALLOY 24, PERMOLD.1,材质：合金24，由模具成型。
工程制图常用英语
工程图常用英语offset section复合剖视compound section剖面图section, sectional view重合剖面coincide section, revolved section移出剖面removed section剖面线section line剖面符号symbols for section-lining习惯画法conventional drawing局部放大图drawing of partial enlargement零件图detail drawing, working drawing第三角投影third angle projection粗实线continuous thick line, full line, visible line 细实线continuous thin line虚线dot line, dashed line, hidden line点划线dash and dot line双点划线double dots line波浪线break line断裂线剖切平面迹线cutting plane line尺寸线dimension line尺寸界线extension tine尺寸dimension size箭头arrowhead基准datum基准线datum line基准面datum plane中心孔central hole中心距center distance轴shaft, axle孔hole斜孔inclination装配图assembly drawing性能尺寸characteristic dimension大小尺寸size dimension总体尺寸outer dimension配合尺寸fit dimension内圆角fillet外圆角round尖角sharp corner倒角chamfer轮缘flange of wheel缘、边、环rim轴肩shoulder凸台boss凹坑concave pit轴颈shaft neck轮毂hub轮辐spoke, spoke of wheel直纹滚花straight knurling网纹滚花hatching knurling键槽key-way退刀槽escape拔模斜度pattern draft填料盒gland box油槽oil groove油封oil seal标准件standard parts螺纹thread外螺纹external thread内螺纹internal thread大径major diameter小径minor diameter螺距pitch of thread牙型form of thread旋向direction of turning右旋螺纹right-hand thread左旋螺纹left-hand thread头数number of thread导程lead粗牙coarse thread细牙fin thread螺栓bolt螺钉screw螺柱stud螺母nut垫片washer公差tolerance公差带tolerance zone零线zero line标准公差standard tolerance公差等级tolerance grade基本偏差fundamental deviation 配合fit间隙配合clearance fit过盈interference过盈配合interference fit过渡配合transition fit基孔制hole-basic system of fits基轴制shaft-basic system of fits间隙clearance齿轮gear圆柱齿轮cylindrical gear正齿轮spur gear斜齿轮spiral gear轮齿gear tooth节圆pitch circle齿顶圆addendum circle, outside circle齿根圆root circle, addendum circle模数modulus齿数number of teeth齿高tooth height齿顶高height of addendum齿根高height of addendum齿厚circular thickness齿间tooth space齿宽tooth width压力角angle of pressure弹簧spring销pin圆柱销round pin圆锥销taper pin开口销cotter pin, split键key平键flat key半圆键half round key, woodruff key轴承bearing滚动轴承rolling bearing向心铀承radial bearing密封装置sealing equipment锁紧装置locking equipment粗糙度roughness基本尺寸basic size实际尺寸actual size极限尺寸limits size最大极限尺寸maximum limit of size最小极限尺寸minimum limit of size偏差deviation上偏差upper deviation下偏差lower deviation形状公差tolerance in form, form tolerance 垂直度perpendicularity倾斜度angularity同轴度concentricity对称度symmetry位置度true position直线度straightness平面度flatness圆度roundness圆柱度cylindricity线轮廓度profile of any line面轮廓度profile of any plane位置公差tolerance in position, position tolerances 平行度parallelism跳动run-out圆跳动cycle run-out全跳动total run-out轴测投影axonometric projection轴测投影面plane of axonometric projection轴测图axonometric drawing正等轴测投影isometric projection正二测bimetric projection斜二测oblique bimetric projection轴测轴axonometric axis轴间角axis angle, angle between ales缩短foreshortened轴向缩短率coefficient of axialdeformation ratio of fore shortening for any axis 切割法cutting method, by cutting方箱法boxing method坐标法coordinate method方框法enclosing-square method四心近似法four-center approximate method复合剖视compound section剖面图section, sectional view重合剖面coincide section, revolved section移出剖面removed section剖面线section line剖面符号symbols for section-lining习惯画法conventional drawing局部放大图drawing of partial enlargement零件图detail drawing, working drawing第三角投影third angle projection粗实线continuous thick line, full line, visible line 细实线continuous thin line虚线dot line, dashed line, hidden line点划线dash and dot line双点划线double dots line波浪线break line断裂线剖切平面迹线cutting plane line 尺寸线dimension line尺寸界线extension tine尺寸dimension size箭头arrowhead基准datum基准线datum line基准面datum plane中心孔central hole中心距center distance轴shaft, axle孔hole斜孔inclination装配图assembly drawing性能尺寸characteristic dimension大小尺寸size dimension总体尺寸outer dimension外形尺寸配合尺寸fit dimension内圆角fille。
景观常用英语（图纸中标注必不可少）
景观常用英语（图纸中标注必不可少）预览说明:预览图片所展示的格式为文档的源格式展示,下载源文件没有水印,内容可编辑和复制景观常用英语（图纸中标注必不可少）常用设计英语（图纸中标注必不可少）1. 主入口大门/岗亭（车行&人行）MAIN ENTRANCE GATE/GUARD HOUSE （FOR VEHICLE & PEDESTRIAN ）2. 次入口/岗亭（车行&人行）2ND ENTRANCE GATE/GUARD HOUSE （FOR VEHICLE & PEDESTRIAN ）3. 商业中心入口ENTRANCE TO SHOPPING CTR.4. 水景WATER FEATURE5. 小型露天剧场MINI AMPHI-THEATRE6. 迎宾景观-1WELCOMING FEATURE-17. 观景木台TIMBER DECK （VIEWING）8. 竹园BAMBOO GARDEN9. 漫步广场WALKWAY PLAZA10. 露天咖啡廊OUT DOOR CAFE11. 巨大迎宾水景-2GRAND WELCOMING FEATURE-212. 木桥TIMBER BRIDGE13. 石景、水瀑、洞穴、观景台ROCK'SCAPE WATERFALL'SGROTTO/ VIEWING TERRACE14. 吊桥HANGING BRIDGE15. 休憩台地（低处）LOUNGING TERRACE （LOWER ）16. 休憩台地（高处）LOUNGING TERRACE （UPPER ）17. 特色踏步FEATURE STEPPING STONE18. 野趣小溪RIVER WILD19. 儿童乐园CHILDREN'S PLAYGROUND 20. 旱冰道SLIDE21. 羽毛球场BADMINTON COURT22. 旱景DRY LANDSCAPE23. 日艺园JAPANESE GARDEN24. 旱喷泉DRY FOUNTAIN25. 观景台VIEWING DECK26. 游泳池SWIMMING POOL27. 极可意JACUZZI28. 嬉水池WADING POOL29?儿童泳池CHILDREN'S POOL30. 蜿蜒水墙WINDING WALL31. 石景雕塑ROCK SCULPTURE32. 中心广场CENTRAL PLAZA33. 健身广场EXERCISE PLAZA34. 桥BRIDGE35. 交流广场MEDITATING PLAZA36. 趣味树阵TREE BATTLE FORMATION 37. 停车场PARING AREA38. 特色花架TRELLIS39. 雕塑小道SCULPTURE TRAIL40. （高尔夫）轻击区PUTTING GREEN 41. 高尔夫球会所GOLF CLUBHOUSE 42. 每栋建筑入口ENTRANCE PAVING TO UNIT43. 篮球场BASKETBALL COURT44. 网球场TENNIS COURT45. 阶梯坐台/种植槽TERRACING SEATWALL/PLANTER 46. 广场MAIN PLAZA47. 森林、瀑布FOREST GARDEN WATERFALL 48. 石景园ROCKERY GARDEN49. 旱溪DRY STREAM50. 凉亭PAVILION51. 户外淋浴OUTDOOR SHOWER52. 拉膜结构TENSILE STRUCTURE53. 台阶STAIR54. 高尔夫球车停车场PARKING ( GOLF CAR )55. 健身站EXERCISE STATION56. 晨跑小路JOGGING FOOTPATH57. 车道/人行道DRIVEWAY /SIDEWALK58. 人行漫步道PROMENADE59. 瀑布及跳舞喷泉(入口广场) WATER FALL AND DANCING FOUNTAIN ( ENTRY PLAZA )60. 特色入口ENTRY FEATURE61. 石景广场ROCKERY PLAZA喜阴植物:Shade-requiring plant 喜阳植物：Heliophile 或Light Plant 形容词：Shade-requiri ng, light-requiri ngheliophobe, 嫌阳植物heliopla nt,heliosphere,FEATURE COLUMN LIGHT DETA I 特色灯柱详图PAVING 01 DETAIL特色铺地详图-01大门详图-01 NOTE:THIS PACKAGE IS TO BE READ IN CONJUNCTION WITH THE A0-SIZE DRAWINGS BOUND SEPARATELY.此图册需与分开钉装之A0大小平面图结合使用SKYLIGHT/VENT TREATMENT DETAI 通风井 / 采光井详图FEATURE PLANTER POT 01 DETAIL 特色景盆详图-01FEATURE WALL 水景墙FOUNTAIN 03 （TYPICAL ）水景详图-03（标准）REFER TO LIGHTING PLAN AND DETAIL 参照灯具平面图与详图FROM WATER SOURCE进水 DRAIN TO WASTE 排水太阳能装置日光层xerophilous pla nt,适旱植物；喜旱植物 xerophyte, 旱生植物xerothermal in dex, 干热指数PARTIAL PLAN 局部平面 KEY PLAN IMAGESECTIONELEVATION索引图意向图剖面图立面图轴测图ISOMETRIC VIEWPERSPECTIVE 效果图MASTER LANDSCAPE PLAN 观概念设计平面图MASTER LANDSCAPE CONCEPT PLA N 总体景观设计概念图CIRCULATION DIAGRAM 交通分析LANDSCAPE DESIGN DEVELOPMENT PACKAGE （D 景观设计扩初一阶段图册（ DD1）DRAWING SCHEDULE 图纸目录 DESCRIPTION SKETCHES OF KEY FEATURES FOUNTAIN 01 水景详图 PAVILION 01 景亭详图图纸说明特色景点描绘-01-01TRELLIS 01 -01FEATURE PLANTER POT 01 TYPICAL TREE COLLAR DETAILFEATURE URN DETAILFEATURE WALL DETAIL 01FEATURE SNAIL SCULPTUREFEATURE BRIDGE DETAILFEATURE SCULPTURE 01 DETAILFEATURE ARBOR DETAIL 特色花盆详图-01标准树池详图特色景瓮详图特色景墙详图-01 特色蜗牛详图特色景桥详图特色雕塑详图-01 特色藤架详图GATE 01 DETAILCOMPACTED SUBGRADE 地基压实。
设计图纸常用英语词汇2010.4
幕墙图纸常用英文100词序号名称英文序号名称1图纸目录drawing list34保温岩棉2版本revision35转接件3材料表material list36防烟板4平面plan37三元乙丙胶条5图例legend38紧固件6立面elevation39抽钉7局部立面key elevation40不锈钢8剖面section41土建结构9节点detail42预埋件10典型节点typical detail43槽埋11横剖节点horizontal detail44垫块12竖剖解点vertical detail45室内侧13竖框mullion46室外侧14公竖框male mullion47热浸镀锌15母竖框female mullion48结构胶16上横框head49耐候胶17中横框transom50不锈钢螺栓18下横框sill51塑料胀栓19窗台板sill52室内天花板20横框插芯gutter sleeve53彩釉玻璃21横框前批水板sleeve54自攻钉22顶封修capping55在现场23玻璃垫框spandrel adaptor56在工厂24横扣板horizontal bead57焊接25竖扣板vertical bead58双面贴26齿形垫片serrated washer59泡沫棒27格栅grill60加强筋28背板back pan61排水孔29铝板alum. Panel62表面处理30复合板composite panel63氧化的31可视玻璃vision glass64粉末喷涂32层间玻璃spandrel glass65氟碳喷涂33中空玻璃I.G.U66铝型材说明：本词汇表中的词汇为基本词汇，必须熟练掌握 1/2幕墙图纸常用英文100词序号名称英文序号名称67模具die100备品68钢结构steel structure10169混凝土concrete10270门执手door handle10371门合页door hinge10472化学锚栓chemical anchor10573机械锚栓mechanical anchor10674T型螺栓T bolt10775铝角片alum. Angle10876铝方管alum. Tube10977槽铝alum. Channel11078预先加工孔predrilled11179A向视图 A view11280轴线grid11381混凝土柱concrete column11482百页louver11583清玻clear glass11684着色玻璃tinted glass11785钢化玻璃Tempered glass 11886半钢化玻璃HS glass11987夹胶玻璃laminated glass12088角芯corner cleat12189雨棚canopy12290阳台balcony12391扶手handrail12492典型尺寸typical dim.12593防鸟网bird mesh12694尼龙nylon12795施工图shop drawing12896视觉模型VMU12997试验模型PMU13098公差tolerance13199组件component132说明：本词汇表中的词汇为基本词汇，必须熟练掌握 2/2词英文insulating rockwoolbracketsmoke flashingEPDM gasketfixingrivetstainless steelmain structureembedmentchannel embedmentsetting blockinternalexternalhot dip galvanizedstructural sealantweather sealantss. Boltplastic anchorceilingceramic glassscrewon sitein factorywelddouble side tapebacking rodStiffenerdrain slotfinishanodizedpowder coated/ppcfluorocarbon coatedalum. Extrusion 1/2词英文spare2/2专业词汇总结表-1序号词汇一、幕墙类型1double-skinned curtain wall2point-fixing glass wall3single rope net point-glass curtain wall4rib point –glass curtain wall5steel structure point-glass curtain wall6steel pull rod point-glass curtain wall7double-story point-glass curtain wall8unitized curtain wall9stick curtain wall10semi-unitized curtain wall11metal & glass skylight12energy saving aluminum doors and windows13building maintenance units14steel structure15fish-bellied steel structure二、钢材和铝材16I-shaped steel17welded I-shaped steel18angle steel19channel steel20structure steel21mild steel22satin stainless steel23alum. angel24embedded element25reinforced concrete26concrete slab27anchor steel angle28aluminium extrusion三、板材29panel30composite panel31alu solid sheet32curved pressed aluminium slab edge panels33mild steel panel34stainless steel sheet35aluminium panel36infill panel371/8" continuous alum. flashing38continuous steel bar 15MM x 82MM四、玻璃39Single glass40Double glass41insulated glass42Laminated glass43Fritted glass44Ceramic coated glass45Opacified glass 46Heat strengthened with metallic enamel coating47Tinted solar control glass48Clear annealed safety glass49Thoughened glass50Clear float annealed glass(6mm)51spandrel glass52laminated insulation glass 53insulating vision glass五、密封材料54reinforced membranes of foil55plastic 56lining 57EPDM gaskets 58gasket 59weather stripping 60bubble 61sealant-back rod 62sealant63adhesive64PVB65norton v2100 glazing tape六、门窗及五金件66auto-sliding door 67double side hung doors68sliding door 69top hung vents 70top hung lights71opening lights72fixed lights73lronmongery74friction stay 75handle76deadlock77atch78multipoint fastening79bolt80s-s bolt81nut82anchor bolt83flat washer84spring washer85self-tapping screw86self taping-drilling screw87self-drilling screw88rivet89shear pins901/2" Φanchor bolt91(2) 1/2" Φ bolt 6" long with washer and lock nuts92expansion bolt93z-clip and fastener94temporary fastener七、幕墙主要构件95mullion96transom97stick98beam99slab100alu angle101head102sill103decorative plate104external cover cap105column106louver107floor108roof109canopy110bridge111railing112back panel113perforated panel114bracket115I-shaped steel bracket116alu-core117skylight118shopfront 119trellis120sunshade121isolating spacer122terrace123balcony124rock wool125insulating rock wool126fire-roted rock wool127alu transom128alu mullion129steel mullion130metal wire mesh131anti-leakage gypsum132sub-frame of alu sheet133steel alu combined keel134p allet135al suspending ceiling136waterspout137back of mullion138horizontal139vertical140stair141goods lift142passenger lift143epdm membrane144flashing panel八、幕墙安装工序145soffit146interface147bed seal148fire stopping149fabrication150installation151dismantling152mechanical fixings153fixing anchor154curtain walling installation155fabrication and installation156welding157cleaning158maintenance159assembly160fixing anchor installation161fixing anchor adjustment162performance163criteria164performance criteria165comply with166thermal break167tolertance九、型材表面处理方式 168finish169polyester powder coated170hot dip galvanized171galvanizing172texture十、图纸名称173plan174elevation175section176jambs177nearside178starboard179detail180detail see181storey182survey183level184grid line185shop drawing186as-built drawing187plan188enlarged elevation189indoors ceiling line190scale191full192main structure193kicker anchoring detail connection194level 1,2,3.... 195min. 196nominal197secondary continuous perimeter silicone seal 198section199(section a-a - 32050MM radius wall)200see st3 for plan view201see detail sc8 for connection to slab2026MM ~ 6MM infill w/ vert. Trim 2036MM infill at head condition 2046MM infill at jamb6MM 2056MM infill at jamb w/splice2066MM infill at parapet 2076MM infill over 26MM infill 2086MM infillto 6MM infill 2096MM infill over 6MM infill2106MM infill to 6MM infill w/ splice 2116MM infill w / anchoring 21226MM infill over 6MM infill21326MM ~ 26MM infill at jamb 21426MM infill at bacony door21526MM infill at door jamb21626MM infill at head horizontal21726MM infill at jamb21826MM infill at jamb w/splice21926MM infill at floor slab22026MM infill at soffit entrance22126MM infill w / anchoring22226MM infill to 26MM infill22326MM infill to 26MM infill w/ splice224spare parts225recycling 226sample227obtain approval228torque229figure230wind loads231deflection232dead loads233air permeability234water penetration235wind resistance236thermal properties237solar heat transmission238light transmission239thermal stress in glazing240condensation241relative humidity242moisture243water vapour244three dimensional adjustment 十一、质量缺陷名称245crack 246dimple247scratche 248durable249neutral250insulation 251bonded252mineral 253fibre254rot 255vermin 256moisture 十二、加工方法257acid etched 258machine cut 259drill 260unload 十三、现场施工相关词汇261claim262payment263helmet264safety belt265safety shoe 266scaffold267gondola268lorry 269mobile crane 270tower crane271boom lift272platform273building 274Project 275Site276Office 277Owner278Architect279Engineer280Foreman281Labour 282submission283schedule284programme285commence286subcontractor287main contract288master programme289manual290Purchase291identification292inspection 293dispatch 294installation procedures295survey 十四、进出口术语：296Contract297Original / Copy 298Marks 299Gross weight300Net weight 301Packages 302Measurement 303Specification 304Volume 305Description of Goods306Unit price307Amount / total value308Partial shipment309Transhipment310Direct steamer311Allow 312Prohibit313Beneficiary314Commercial Invoice315Proforma Invoice316Packing List 317B/L （Bill of Lading） 318Vessel 319Voyage 320Port of loading321Port of destination322ETD (Estimated time of departure) 323ETA (Estimated time of arrival)324Shipping advice325Air Waybill326MAWB（Master air waybill）327HAWB ( House air waybill)328Flight No.329Certificate of Fumigation330Customs declaration331Import and Export332Insurance Policy333Premium334All risks335War risk 336Franchise337Terms of payment338T/T（Telegraphic Transfer ） 339L/C ( Letter of Credit )340Buyer341Seller342Consignor ( Shipper )343Consignee344Notify party345Carrier346Forwarding agent347FCL (Full container load)348LCL (Less than container load)349Container350Container/Seal No.351Freight352Freight prepaid353Freight to be collect354Haulage355Customs356Customs clearance357FOB (Free on board)358CFR (Cost and freight)359CIF (Cost, insurance and freight)360EXW (Ex. Works)361Warehouse 362HS Code363Duty 364VAT (Value added tax) 365EMP (European main ports)366Logistics十五、其他3671/2" Φ bolt 6" long with washer, lock nut and pipe sleeve field match drill steel angle and alum. Plate3681/2" Φ bolt 6" long with washer and lock nut field match drill steel angle and steel anchor369(2) 1 / 2" Φ X 6" bolts w/ flat washer, lock washer and nut field match drill mullion370 1 1/2" x 1 1/2" alum. angle 8" lg 24" o.c.3711 / 2" Φ X 2" bolts w/ flat washer, lock washer and nut and slip shims field match drill mullion and steel bearing plate37225000MM radius wall37328700MM radius wall3743MM alum. pipe sleeve37532050MM radius wall3765" x 5 1/4" x 1/8" thk. alum. Plate37750-55 durometer shore a neoptene side blocks locate at upper quadrant of each shallow pocket jamb37850-55 durometer shore a neoptene " w " side blocks locate at upper quadrant of each deep pocket jamb37965.0MM to face of slab3807900MM radius wall3817900 wall elevation38280-90 durometer shore a neoprene setting blocks 150MM lonng at quarter pts3838" alum. splice sleeve center between mullions3849MM weep holes at quater pts.3859/16" x 3" slot in alum. plate and steel bar 386alum. panel soffit by others387alum. splice sleeve at mullion joint388anchor bolt389anchor bolt connection390at splice391approx.392continuous silicone perimeter seal393continuous silicone seal394door and subframe by others395expension horizontal396fix fasten splice sleeve to lower mullion 397 high impact polystyrene shim398interior silicone perimeter seal399notch stem of mullion at butt joint glaxed spandrel area400note: 28MM insulated vision glass will be needed on floors 34 - 38 on the 6900 all (high wind load regions) w401paneling by others402primary continuous perimeter silicone seal 403provide bond breaker tape at splice sleeve at sealed joint404seal flashing to face of slab405set in sealant406shim as required407silicone perimeter seal408steel reininforce section409surround by others410surroundings by others411splice sleeve412splice plate with bond breaker tape and sealant at joints in closure413silicone sealant w/ rod414structural silicone415Norton v2100 glazing tape416trim cover below417typ. 26mm infill jamb418typical cantilever anchoring业词汇总结表-1翻译双层动态节能幕墙点支式玻璃幕墙单层索点支式幕墙肋驳接点支幕墙钢结构点支幕墙钢拉杆点支幕墙双层索点支幕墙单元式幕墙框架式幕墙半单元式幕墙金属及玻璃屋面节能环保铝合金门窗擦窗机钢结构鱼腹钢结构工字钢焊接工字钢角钢槽钢结构钢低碳钢镜面不锈钢角铝埋件钢筋混凝土混凝土楼板锚固角钢铝制挤压型材板复合板铝单板边梁处弯弧铝板低碳钢板不锈钢板铝板内有岩棉或填充剂的板1/8英寸厚连续铝防水板连续钢板10MM x 82MM单玻璃中空玻璃中空玻璃夹胶玻璃彩釉玻璃（经内部加工）彩釉玻璃（经外部加工）不透明玻璃半钢化、金属彩釉玻璃带彩色的（本体的）控制太阳光的玻璃退火、安全清玻璃钢化玻璃退火浮法玻璃（6mm）窗间墙玻璃夹胶中空玻璃中空视窗玻璃金尾薄片、薄箔塑料衬砌、衬垫，垫板EPDM 胶条胶条毛条起泡、泡沫泡沫条密封胶粘合剂PVB(聚乙烯醇缩丁醛)胶片玻璃装配胶带（诺顿V2100）自动平移门双扇平开门推拉门上悬窗上悬窗顶部的固定扇开启扇固定扇五金件磨擦绞链执手装配死栓的锁门插销多点锁紧螺栓不锈钢螺栓螺母锚栓平垫弹垫自攻钉自攻自钻钉自钻钉铆钉剪切销钉1/2"英寸直径锚固螺栓(2) 直径1 / 2英寸,长度6英寸的螺栓, 带有垫片和自锁螺母.膨胀螺栓z 形卡件和紧固件临时紧固件竖框横框框架梁边梁角铝顶窗台扣板外扣板柱子百叶地面屋面雨蓬廊桥扶手背衬板穿孔板转接件工字钢制转接件铝插芯天窗橱窗格栅遮阳、天棚隔离垫片露天平台阳台岩棉保温岩棉防火岩棉铝横框铝竖框钢竖框金属丝网防水石膏板铝板副框钢铝结合竖龙骨托板铝悬置天花板排水口立柱背面水平垂直楼梯货梯客梯EPDM膜板防水板吊顶封修底密封防火加工安装拆除机械固定锚固件幕墙的安装生产和安装焊接清洗、指对帷幕维修、保修组装、装配锚固件安装锚固件调整性能标准性能标准符合断热公差表面处理聚酯粉末喷涂（PPC）热浸镀锌镀锌纹理平面立面剖面侧面近侧右侧详细节点详见层测量、放线水平、标高网格线施工图纸竣工图平面图内装饰线比例比例1:1主结构锚固支撑架连接图一层, 二层,.....最小额定尺寸第二道连续周边硅胶密封剖面a-a 剖面,32050MM半径墙面平面图见图st3与楼板连接详见图sc8.6MM玻璃 / 6MM 玻璃立柱及竖直饰盖的垂直节点图镶嵌6MM 玻璃的顶框水平节点图玻璃边框垂直节点6MM玻璃边框相接转角及立柱拼接套垂直节点图女儿墙处 6MM玻璃横梁节点图6MM玻璃上/26MM 玻璃下横梁水平节点图6MM 玻璃/ 6MM 玻璃立柱垂直节点图6MM 玻璃上/6MM 玻璃下横梁节点图6MM 玻璃 / 6MM玻璃立柱及拼接套垂直节点图6MM 玻璃及锚固件立柱节点图26MM玻璃上/6MM 玻璃下横梁节点图26MM ~ 26MM 玻璃边框相接转角垂直节点图26MM 玻璃横梁与阳台门框交界水平节点26MM 玻璃边框与门侧框交界垂直节点26MM 玻璃顶框水平节点26MM 玻璃边框垂直节点26MM玻璃边框相接转角及立柱拼接套垂直节点图2楼板处26MM 玻璃镶嵌横梁水平节点入口挑檐26MM 玻璃镶嵌横梁节点26MM 玻璃 及锚固件立柱节点图26MM 玻璃/ 26MM 玻璃立柱节点图26mm 玻璃 / 26MM 玻璃立柱及拼接套节点图备件重复利用样品获得同意扭矩、转矩数字，图风荷载偏转、挠度固定荷载空气渗透性渗水性、突破抗风压性隔热性能热传导系数玻璃的热应力凝点、凝露湿温相对度潮湿、湿气蒸气、水蒸气三维调整裂缝波纹划伤耐用的、耐磨的，中性的隔热、分隔粘结的、砌合的、化合的矿物、矿石、无机物纤维、构造、纤维制品、（植）须根 腐蚀，腐烂害虫、寄生虫、害兽、害鸟湿度、水分、潮气酸蚀、磨砂腐蚀的切断、切削钻卸货索赔付款安全帽安全带安全鞋脚手架吊篮货车汽车吊塔吊升降车操作平台建筑物、大厦工程项目现场办公室业主建筑师工程师工长劳动力递交时间表、进度表、一览表进度表开工总包商总包商的工作计划手册、指南采购辨认、鉴定，证明检查，视觉发运、分派、派遣安装程序，手续测量、勘定、审视、视察合同正本/副本唛头毛重净重件数尺码规格体积品名单价总值分批装运转船直达轮允许不允许受益人商业发票形式发票箱单提单船航次装运港目的港预计离港时间预计到达时间发运通知航空运单主单分单航班号熏蒸证报关单进出口保险单保险费一切险战争险免赔额付款方式电汇信用证买方给卖方发货人收货人通知方承运人货运代理货 （ 整柜）拼箱货 （拼箱）集装箱箱号/封号运费运费预付运费到付拖车费海关清关离岸价成本加运费到岸价工厂交货仓库商品代码关税增值税欧基港物流直径1 / 2英寸,长度6英寸的螺栓, 带有垫片、自锁螺母和套管. 现场对正角钢和铝板钻孔直径1 / 2英寸,长度6英寸螺栓, 带有垫片, 自锁螺母. 现场对正角钢和锚固板钻孔(2) 1 / 2" Φ X 6" 英寸螺栓,平垫圈,防松垫圈,螺母, 现场立柱钻孔对正1 1/2" x 1 1/2" 英寸角铝, 8英寸长, 24英寸中心1 / 2" Φ X 2" 英寸螺栓,平垫圈,防松垫圈,螺母和隔离垫片,现场在立柱和支承钢板上对正钻孔25000MM 半径圆弧墙面28700MM 半径圆弧墙面3mm 铝套管32050MM半径圆弧墙面5" x 5 1/4" x 1/8" 英寸铝板氯丁橡胶侧垫块，邵氏硬度a50-55，位于每个浅槽边框上端四分之一点。
图纸英语对照表
详图、大样图、接点图 record drawing
修改图竣工图 as-completed drawing； as-built drawing
图名 title
公称直径 nominal diameter(DN)
外径 outside diameter(OD)
内径 inside diameter(ID)
一览表 list； breviate； catalogue
风机动力型VAV-CAV末端 fan power VAV-CAV terminal units
保持最新技术 keep with the latest technology
中国唯一的销售商 the sole Chinese distributor
水压试验 hydraulic test
渗漏 leakage
关闭 close
型号、类型 type； model
尺寸、体积 size； volume
设备购买，运输，质量保证 Appurtenances purchase, delivery and warranties
执行设计计划并应对工程部门的检查Implementing the design plan and subject the work to the inspection of the Engineering Department
设计图 layout；design
施工图 final
平面图 plan
立面图 elevation
剖面图 SECTION
工程管理，设计，施工，服务，或者商务管理 project management, design, construction, service, or business administration
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
复合剖视compound section剖面图section, sectional view重合剖面coincide section, revolved section移出剖面removed section剖面线section line剖面符号symbols for section-lining习惯画法conventional drawing局部放大图drawing of partial enlargement零件图detail drawing, working drawing第三角投影third angle projection粗实线continuous thick line, full line, visible line细实线continuous thin line虚线dot line, dashed line, hidden line点划线dash and dot line双点划线double dots line波浪线断裂线break line剖切平面迹线cutting plane line尺寸线dimension line尺寸界线extension tine尺寸dimension size箭头arrowhead基准datum基准线datum line基准面datum plane中心孔central hole中心距center distance轴shaft, axle孔hole斜孔inclination装配图assembly drawing性能尺寸characteristic dimension大小尺寸size dimension总体尺寸外形尺寸outer dimension配合尺寸fit dimension内圆角fillet外圆角round尖角sharp corner倒角chamfer轮缘flange of wheel缘、边、环rim轴肩shoulder凸台boss凹坑concave pit 轴颈shaft neck轮毂hub轮辐spoke, spoke of wheel直纹滚花straight knurling s网纹滚花hatching knurling键槽key-way退刀槽escape拔模斜度pattern draft填料盒gland box油槽oil groove油封oil seal标准件standard parts螺纹thread外螺纹external thread内螺纹internal thread大径major diameter小径minor diameter螺距pitch of thread牙型form of thread旋向direction of turning右旋螺纹right-hand thread左旋螺纹left-hand thread头数number of thread导程lead粗牙coarse thread细牙fin thread螺栓bolt螺钉screw螺柱stud螺母nut垫片washer公差tolerance公差带tolerance zone零线zero line标准公差standard tolerance公差等级tolerance grade基本偏差fundamental deviation配合fit间隙配合clearance fit过盈interference过盈配合interference fit过渡配合transition fit基孔制hole-basic system of fits基轴制shaft-basic system of fits间隙clearance形状公差tolerance in form, form tolerance直线度straightness平面度flatness圆度roundness圆柱度cylindricity线轮廓度profile of any line面轮廓度profile of any plane位置公差tolerance in position, position tolerances平行度parallelism齿轮gear圆柱齿轮cylindrical gear正齿轮spur gear斜齿轮spiral gear轮齿gear tooth节圆pitch circle齿顶圆addendum circle, outside circle齿根圆root circle, addendum circle模数modulus齿数number of teeth齿高tooth height齿顶高height of addendum齿根高height of addendum齿厚circular thickness齿间tooth space齿宽tooth width压力角angle of pressure弹簧spring销pin圆柱销round pin圆锥销taper pin开口销cotter pin, split键key平键flat key半圆键half round key, woodruff key轴承bearing滚动轴承rolling bearing向心铀承radial bearing密封装置sealing equipment锁紧装置locking equipment粗糙度roughness基本尺寸basic size实际尺寸actual size极限尺寸limits size最大极限尺寸maximum limit of size最小极限尺寸minimum limit of size偏差deviation 上偏差upper deviation下偏差lower deviation垂直度perpendicularity倾斜度angularity同轴度concentricity对称度symmetry位置度true position跳动run-out圆跳动cycle run-out全跳动total run-out轴测投影axonometric projection轴测投影面plane of axonometric projection 轴测图axonometric drawing正等轴测投影isometric projection正二测bimetric projection斜二测oblique bimetric projection轴测轴axonometric axis轴间角axis angle, angle between ales缩短foreshortened轴向缩短率coefficient of axial deformation ratio offore shortening for any axis切割法cutting method, by cutting方箱法boxing method坐标法coordinate method方框法enclosing-square method四心近似法four-center approximate method机械工程图中常用的英语词汇Abbreviation 缩写Accuracy 精度、准确性Acme thread 梯形螺纹(29°)Addendum 齿顶高Addendum angle 齿顶角Addendum circle 齿顶圆Addendum of mating gear 啮合齿轮的齿顶高Adjacent-part lines 相邻零件线Aligned sections 旋转剖视Aligned view旋转视图Allowance 容差、加工余量Alloy 合金Alloy steel 合金钢Alphabet 字母Alteration 变更、更改Alternate-position views 位置改变的视图Alternator 交流发电机Induction alternator 感应(交流)发电机Motor alternator 电动(交流)发电机Single-phase alternator 单向(交流)发电机Synchronous alternator 同步(交流)发电机Three-phase alternator 三相(交流)发电机Amount 总量、总计Analyzable assembly 分析装配图Anchor bolt 地脚螺栓Angles 角Acute angle 锐角Blunt angle 钝角Right angle 直角Sliding angle 摩擦角Spiral angle 螺旋角Taper angle 锥角Angular 有角的Angular bearing 径向止推轴承Angular bevel gears 斜交伞齿轮Angular gear人字齿轮Angular section斜剖面Anneal 退火Approval 批准、许可Arc 弧、圆弧Arc thickness 弧长厚度(齿厚)Arc welding 弧焊Arrangement 布置、装置Arrangement of views 视图的布置Clamping arrangement 夹紧装置Cramping arrangement 紧固装置General arrangement 总体布置Arrow 箭头Arrowheads 箭头Assembly 装配图、组装图Assembly drawing 装配图Assembly drawing number 装配图图号Assembly for installation 安装图Assembly parts 组装配合零件Assembly sections 装配图剖视Assembly sketches 装配草图Auxiliary elevation 辅助立面图Auxiliary line辅助线Auxiliary section 辅助剖视Auxiliary surface 辅助面Auxiliary view 辅助视图Average 平均数Axial 轴的、轴向的Axial pitch 轴向节距Axial plane 轴向平面Axial thickness 轴向厚度Axis 轴线、中心线Axis of revolution 回转轴线Axis of rotation 旋转轴线Axis of symmetry 对称轴线Horizontal axis 水平轴Major axis 长轴Minor axis 短轴Vertical axis 垂直轴X axis X轴Y axis Y轴Axle 轴Axle bearing 轴向(止推)轴承Axle sleeve 轴向(止推)套筒Axonometric drawing 轴测图Babbitt 巴氏合金Back cone 背锥Back cone radius 背锥半径Back elevation 后视图Backstop 托架、棘爪Ball bearing 球轴承Bar 杆Angle bar 角钢Channel bar 槽钢Flat bar 扁钢Round bar 圆棒、圆钢Base 基础、底座、基线、基面、基准Base circle 基圆Base circular thickness 基圆弧线齿厚Base cylinder 基圆柱Base helix angle 基圆上的螺旋角Base plane 基平面Base point 基点Key base 键座Basic circle 基准圆Basic hole system 基孔制Base shaft system 基轴制Basic size 基本尺寸、公称尺寸、标称直径Basis 基础、基准、基线Battery 电池、蓄电池Bearing 轴承、支撑、方位Bearing accuracy 定位精度Bearing box 轴承箱Bearing brass 铜轴衬Bearing bridge 轴承支架Bearing oil seal 轴承油封圈Bearing support 轴承架Bearing unit 轴承组合件Anti-friction bearing 减摩轴承Ball and socket bearing 球窝轴承Conical bearing 锥形轴承Journal bearing 径向轴承Needle bearing 滚针轴承Plain bearing 滑动轴承Roller bearing 滚柱轴承Self-aligning bearing 自位轴承Thrust bearing 止推轴承Belt 带、皮带Bench 工作台Work bench 工作台Bend 弯头、接头Elbow bend 肘形弯管Normal bend 正弯管(90°) Bender 弯曲机Bending 挠曲Bending strength 抗弯强度Bent axle 曲轴Bevel 倾斜的、斜角的、斜面Bevel gear 圆锥齿轮、伞齿轮Bevel pinion 小圆锥齿轮Bevel washer 斜垫圈Bevel wheel 伞齿轮、斜摩擦齿轮Bilateral tolerance 双向公差Bill of materials 送料单Block in、block out 画草图Blue paper 蓝晒纸Blueprint 蓝图、设计图Board 板、(管理)局、厅Bottom board 底板Moulding board 模板Body 机体、机身Boiler 锅炉Bolt 螺栓、插销Adjusting bolt 调整螺栓Assembling bolt 装配螺栓Binding bolt 连接螺栓Bright blot 光制螺栓Captive bolt 固定螺栓Double-screw bolt 双头螺栓Fitter bolt 装配螺栓Foundation bolt 地脚螺栓Hexagonal head bolt 六角头螺栓Hook bolt 钩形螺栓Screw bolt 全螺纹螺栓Snap bolt 圆头螺栓Tension bolt 拉紧螺栓Bolted joints 螺栓连接Book 书、册Hand book 手册Instruction book 说明书Bore face machine 镗孔端面加工机床Borer 镗床Jig borer 坐标镗床Table borer 台式镗床Boring 镗孔Boring machine 镗床Boring mill 镗床Bottom case 底座Bottom clearance 径向间隙Bottom view 底视图Bracket 托架、支柱Brake 制动器、闸Brass 黄铜、铜轴衬Braze 铜焊Brazing 铜焊Breadth 宽度、厚度Break line 断裂线Brinell figure (number) 布氏硬度Brinell hardness 布氏硬度Broacher 拉床、绞孔机Broaching 扩孔机、拉床、拉削Broken circle 虚线圆Broken out section 断裂剖面Broken view 局部视图Bronze 青铜Burnishing 抛光、磨光Burr 三角矬、毛刺、去毛刺Bush 衬套、轴瓦Bushing 轴衬、衬套、套管Butt joint 对接焊Butterfly nut 蝶形螺母Butterfly valve 蝶形阀Button 按钮Push button 控制按钮Cable 电缆Cage 盒、罩、箱Caliper 卡尺、卡钳Gauge caliper 卡规、量规Internal caliper 内卡钳Sliding (vernier) caliper 游标卡尺Cam 凸轮Cam design 凸轮设计Cam shaft 凸轮轴Actuating cam 主动凸轮Adjustable cam 可调凸轮Control cam 控制凸轮Cap 盖、帽、罩Cap screw 带帽螺钉Capital 大写字母Carburizing 渗碳Card 卡片Cartographer 制图员Cartography 制图学、制图法Case 箱、盒、容器、表面Case hardened 表面淬火、硬化Nitrogen case hardening 渗氮硬化Casing箱、盒、壳Oil pump casing 油泵(壳)Casting 铸造、铸件Defect casting 铸件缺陷Die casting 压铸Sand casting 砂型铸造Spun casting 离心铸造Steel casting 铸钢Cast-iron 铸铁Castle circular nut 六角圆螺母Castle nut 蝶形螺母Catalogue data 表列数据Cave 凹槽、内腔Centre 中心、圆心Centre distance 中心距Centre hole 中心孔Centre line 中心线Centre-section 中心剖面Centre to centre 中心距Centesimal 百分的、百分之一的Centimeter 厘米、公分Central hole 中心孔Central plane 中心平面Central projection 中心投影Chafe 摩擦、磨损Chain 链Drive chain 主动链Transmission chain 传动链Chamfer 倒角、倒棱、斜面Dimensioning of chamfer 倒角的尺寸注法Changes on drawing 图的更改Channel 沟槽Chapter 章Chart 图表、计算图Chart of symbols 符号图表Auxiliary chart 辅助图Dimensions chart 外廓尺寸图Graphical chart 图表Process chart 工艺程序图Progress chart 工艺程序表、工作进度表Charting 制图(表)、填图Check 校验、校核、制动装置Check drawings 校图Check nut 防松螺母Check ring 挡圈Check test校核试验Chief draftsman 主任制图员Chromium 铬Chromizing 镀铬处理Circle 圆、圆周Circle of reference 参考圆Addendum circle 齿顶圆Base circle 基圆Graduated circle 分度圆Imaginary circle 虚圆Outside circle 齿顶圆、外圆Pitch circle 节圆Rack circle 平面齿轮、扇形齿轮Root circle 根圆Top circle齿顶圆Circular cylinder 圆柱Circular pitch 弧线节距Circular thickness 弧线(齿)厚度Circumference 圆周长Clamp 夹紧、夹板Class 种类Class of fit 配合级别Classification 分类Claw 爪、钩、卡爪Clearance fit 间隙配合Clevice /clevis U形钩、U形夹Clevis bolt 套环(插销)螺栓Clevis pin U形夹销Clockwise 顺时针方向Clutch 离合器、联轴器Coat 外层、涂镀层Coat of metal 金属镀层First coat 底漆Coating 镀、覆盖Electrodeposited coating 电镀层Coaxial circle 共轴圆Cock 旋塞Coil 蛇形管、螺管、线圈Coil spring 盘簧Coincident line 重叠线Cold-rolled steel 冷轧钢Collet 夹头Collet chuck 弹簧夹头Color-harden 着色硬化、发蓝、煮黑Common difference 公差Company 公司Joint company 股份公司Limited company 有限公司Compass 圆规Compass of proportion 比例规Component 零件、构件Compression spring 压力弹簧Compressor 压缩机Computer 计算机Concave face 凹面Concentricity 同心度Cone 圆锥Cones development 锥面展开Cone pulley 锥形轮、塔轮Conical spring 锥形弹簧Connection 联接Bolt-on connection 螺栓联接Flange connection 法兰联接Rivet connection 铆钉联接Screw connection 螺钉联接Contact 接触、接合、啮合Contact angle 啮合角Angular contact ball bearing 向心止推球轴承Contour 外形、轮廓线Contracted drawing 缩图Contrast 对比、对照、比较Convention 惯例、常规、习惯Convention for materials 材料的习惯表示法Conventional break 习惯断裂画法Conventional diagram 习惯画法Conventional intersection 习惯交线(画法) Conventional practice 习惯画法Conventional sign 图例、习惯符号|Convex 凸面Conveyer 输送机、传送机Cooler 冷冻机Coordinate axis 坐标轴Coordinate paper 方格纸、坐标纸Copper 铜Copy 抄本、样板Correction 校正、修正Cotter pin 开口销Split cotter 开口销Counterbore 埋头孔、锥口孔Counterclockwise 逆时针方向Countersink 埋头孔、沉孔Countersink drill 中心钻、钻Countersunk 钻埋头孔、钻锥口孔Countersunk bolt 埋头螺钉Countersunk head 埋头Countersunk hole 锥坑Coupling 联轴节Cover 盖、罩Cylinder cover 汽缸盖Dust cover 防尘罩Cowl 壳、套、盖Crane 起重机Crank 曲柄、曲轴Crankshaft 曲轴Crest 峰、尖、牙尖Cross head 十字头Cross section 横剖面、横断面Crown gear 冕状齿轮Cube 立方形体、正六面体Current 电流Curvature 曲率Curvature radius 曲率半径Curve 弯曲、曲线、曲线板Curve plotter 绘图仪Curve ruler 曲线板French curve 曲线板Moment curve 力矩曲线、力矩图Cutter 刀、刀具Cutting plane 截平面Cutting plane symbols 剖切(迹线)平面符号Cycloid 摆线Cycloidal gear 摆线齿轮Cylinder 圆柱体Cylinder base 汽缸座Pump cylinder 泵缸Cylindrical cam 圆柱凸轮Cylindrical fit 圆柱配合Cylindrical roller bearing 圆柱滚子轴承Dash 短划线、虚线、破折号Dash and dot line 点划线Broken dash 断裂线Data 数据、资料Engineering data工程数据Master data 主要数据Date 日期、年代Datum 基准(点、线、面)、资料Datum line 基准线Datum point 基准点Datum plane 基准面Decade 十进制、十进位Decelerator 减速器、制动器、缓动装置Decimal 小数的、十进位小数的Decimal fraction 十进制分数Decimal fraction system 十进小数制Decimal scale 十进位比例尺Decimeter 分米、公分Dedendum angle 齿根角Dedendum circle 齿根圆Definition 定义Deformation 变形、扭曲Degree 度、程度Degree of accuracy 精度Degree of freedom 自由度Degree of hardness 硬度Degree scale 刻度Circular degree 圆度Delineation 轮廓、草图Delineator 制图者Department 科、处、系、车间Draft department 设计科Engineering department 技术科Fitting department 装配车间Heat treatment department 热处理车间Mechanical department 机加工车间Processing department 工艺科Depth 深度、高度Depth dial gauge 深度千分表Depth of engagement 啮合深度Depth of thread 螺纹深度Depth of tooth 齿高Contact depth of tooth 啮合高度Working depth of tooth 齿工作高度Derivation 偏差Standard derivation 标准偏差Description 描述、作图、绘制Design 设计、计划Design activity 设计机关(组织) Design assembly 设计装配图Design drawing 设计图Design layout 设计草图、初步设计图Preliminary design 初步设计Standard design 标准设计Technical design 技术设计Designation 符号、标志Designation strip 铭牌Designer 设计员、制图者、设计师Desk 桌、控制台Drawing desk 绘图桌Detail 细目、细节、详图、零件Detail drawing 详图、零件工作图Detail paper底图纸、描图纸Detail specification 详细规格Detent 棘爪、扳手、制动器Developable surface 可展曲面Developed view 展开图Development inner port 内表面展开图Development of surface 表面展开图Deviation 偏差、偏移Angular deviation 角偏差Average deviation 平均偏差Standard deviation 标准偏差Tolerance deviation 允许偏差Device 装置、设备Diagram 示意图、图解Diagram drawing 图解图、结构图Arrangement diagram 布置图Assembly diagram 装配示意图Block diagram 方框图Schematic diagram 原理图、简图Diagrammatic drawing 草图、示意图Dial gauge 千分表Dial inside micrometer 内径千分表Diameter 直径Diameter of aperture 孔径Diameter of pitch circle 节圆直径Diameter pitch (齿轮)径节Diameter run-out径向跳动Major diameter 大直径、螺纹外径Minor diameter 小直径、螺纹内径Nominal diameter 公称直径Pitch diameter of screw thread 螺纹中径Thread diameter 螺纹外径(直径) Diametral pitch 齿轮径节Die 模具、扳牙Diesel 柴油机、内燃机Dimension 尺寸Dimension line 尺寸线Limiting dimension 极限尺寸Nominal dimension 公称尺寸Outer dimension 外形尺寸、轮廓尺寸Direction 方位、方向Clockwise direction 顺时针方向Disc = disk 圆盘、原板Disk cam 圆盘凸轮Dismount 拆卸Dismountable 可拆卸的Displacement 移位、变位Distance 距离、路程Distortion 变形、歪扭Distribution 分配、分布、配置Ditto machine 复印机Diversion 变更、转换Dividing head 分规Dot line 虚线Dotted line 虚线Double dots line 双点划线Double helical pinion 人字小齿轮Double helical spur gear 人字齿轮Double thread 双头螺柱Dowel thread 定位销、圆柱销Dozer 推土机Draft = draught (拔模)斜度、草图、制图Drafting 制图Drafting board 制图板Drafting machine 制图机Drafting tape 制图带、胶带Draftsman 绘图员Drawer 制图员Drawing 绘图、图样Drawing board 绘图纸Drawing control 图样管理Drawing free-head 草图Drawing instrument 绘图仪器Drawing number 图号Drawing pencil 绘图铅笔Drawing pin 图钉Drawing size 图纸尺寸Drawing table 制图桌Drawing with compass 用圆规画图Blue print drawing 蓝图Free hand drawing 徒手图Full size drawing 原大图Skeleton drawing 草图、结构图Working drawing 施工图、制造图、工作图Drill 钻孔、穿孔、穿孔器Drive 传动、驱动Drive fit 打入配合Air drive 气动Belt drive 带传动Chain drive 链传动Friction drive 摩擦传动Gear drive 齿轮传动Hydromatic drive 液压传动Speed-reducer drive 减速器传动Variable-speed drive 变速传动Worm-wheel drive 蜗轮传动Driven gear 从动齿轮Driven shaft 从动轴Driving gear 主动齿轮Driving shaft 主动轴Drum cam 凸轮轴Ductile iron 球墨铸铁Duplicating tracing 复制描图Durometer (钢轨)硬度计Dusting cloth 抹灰布、撒粉布Eccentricity 偏心距Edge iron 角铁Edge round 外圆角Edge view 边视图Effective diameter 有效直径Effective face width 有效齿宽Efficiency 效率、性能Mechanical efficiency 机械效率Elastic deformation 弹性变形Elasticity 弹性Elbow 肘形弯管、弯头Electric current 电流Electric element 电池Elephant 绘图纸(28X23英寸)Elevation 正面图、立视图End 末端、头Ball end 秋端Butt end 平端、端面Tail end 尾端Top end 顶端Engagement 啮合Engineer 工程技术人员、工程师Engineer-in-chief 总工程师Equipment 设备Eraser 橡皮Erasing shield 擦图片Erection diagram 安装图、装配图Error 误差Accumulated error 累积误差Allowance error 容许误差Average error 平均误差Permissible error 容许误差Relative error 相对误差Exterior 外表面External 外部External diameter 外径External dimension 外形尺寸External fillet 外圆角External thread 外螺纹Extra fine(screw)特细牙螺纹Eyelet = eyelet-hole 小孔Fabrication 建造、制造Face 面、正面、表面、端面Face cam 平面凸轮Face gear 平面齿轮Face hardening 表面硬化Inner face 里面Outer face 外面Face off 倒角Factor of safety 安全系数Factory 工厂、制造厂Factory made 工厂制造的Fastener 接合件、紧固件Fastening 连接件、紧固件Fatigue 疲劳Faucet 旋塞、龙头、开关Feather 滑键、冒口Feather key 滑键Feature 特征、特性、性能Basic mechanical design feature 主要机械设计性能Mechanical feature 机械性能(特性)Feed-pump 供油泵、供水泵Feet 英尺Ferrous metal 黑色金属Field 工场、现场Figure 形状、图样、插图、数字File 锉刀、锉平Filler 填料、垫片Fillet (内)圆角、填角、嵌条Fillet radius 内圆角半径Filter 过滤器Fine thread series 细螺纹级(系列)Finish 完工、加工、磨光Finish all over 全部加工Finish marks 加工符号Machine finish 机器光制Fit 配合Clearance fit 间隙配合Free fit 自由配合Interference fit 静配合Light press fit 轻压配合Light running fit 轻传动配合Loose fit 松配合Normal-running fit 传动配合Running fit 动配合Shrink fit 冷缩配合Slide fit 滑动配合Transition fit 过渡配合Fix 安装、装配、调整、修理、固定Flange 法兰盘、凸缘Flank 边、侧面、齿侧、后面Flat 扁头、平面Flat key 平键Flat spring 板弹簧Flat surface 平面Flexible disk coupling 挠性盘形联轴节Flexible gear-type coupling 挠性齿轮联轴节Flywheel 飞轮Foot 英尺Foot screw 地脚螺钉Force 力Fore word 序、前言Forge 锻Forge steel 锻钢Former 样板、模型、量规Wooden former 木模Formula 公式Foundation 基础、基座Foundation bolt 地脚螺栓Foundry 铸件、铸工车间Fraction 分数、小数Front view 前视图、主视图Full diameter 大直径、主直径Full line 实线Full size 原大Full scale 原大Full section 全剖视Full section view 全剖视图Furbish 研磨、擦光Fuse 保险丝、熔断器Gage = gauge 量规Gallon 加仑Galvanize 镀锌、电镀Gasket 垫圈、密封垫Gasket material 填料Gasoline engine 汽油(内燃)机Gate 门、阀门Gear 齿轮Gear addendum angle 齿顶角Gear box(case) 齿轮箱Gear centre 齿轮中心Gear dedendum angle 齿根角(圆锥齿轮) Epicyclic gear 行星齿轮Herringbone gear 人字齿轮Ratchet gear 棘轮General drawing 总图Geometry 几何学Gland 压盖、填料盖、密封装置Glass 玻璃Glasscloth 砂布、玻璃布Glossary 词汇(表)Grade 等级、斜度Steel grade 钢号Graduated hardening 分级淬火Graduated scale 比例尺、分度尺Gram 克Graph 图(表、解、形)、曲线图Graph paper 方格纸Graphic图示、制图学Grease 滑脂Grind 磨削、抛光Grinding machine 磨床Grinding wheel 砂轮Groove cam 槽凸轮Groove pulley 槽轮、三角带轮Guide 手册、指南Guide bar 导杆Guide pin 定位销、导向销Guide screw 丝杠Guidebook 参考手册、指南、入门Half 二分之一、一部分Half bearing 轴瓦Half section 半剖视Half section view 半剖视图Hammer 锤子Handbook 手册、指南Hand-made 手工制造的Hand-operated 手控的Handle 手柄Hand wheel 手轮Hard casting 白口铁Hard drawn 冷拔Hard rolled 冷轧的Hard surfacing 表面硬化Harden 淬火、硬化Hardened and tempered 调质的Hardened-steel 淬火钢Hardening 硬化Hardness 硬度Hardometer 硬度计Hatch 剖面线H-beam 工字梁、H形梁Heat–treatment 热处理Heavy force fit 重压配合Height 高度Helical bevel gear 螺旋伞齿轮Helical gear 螺旋齿轮、圆柱斜齿轮Helical rack 斜齿齿条Helical spring 螺旋弹簧Hex nut 六角螺母Hexagon jam nut 六角锁紧螺母Hexagon socket head 内六角头Hidden line 虚线Hidden outline 看不见的轮廓线High-carbon steel 高碳钢High-duty 重型的、大型的、优产的High-speed steel 高速钢Hosting jack 千斤顶Hole 孔Horizontal datum plane 水平基准面Horizontal line 水平线Horizontal projection 水平投影Horizontal projection plane 水平投影面Horse-power 马力、功率Hose 软管Hose coupling 软管接头Hot-rolled steel 热轧钢Hot-work 热加工Hour 小时Housing 机座Housing of pump 泵体Bearing housing 轴承箱Gear housing 齿轮箱Hub 轮、中心、衬套I-beam 工字钢Illustration 插图、实例Inaccuracy 不精确、不准确Incenter 内(切圆)心Inch 英寸Incline 斜度、斜面Index plate 分度盘Indicator 指示计、百分表Industrial 工业公司Industrial drawing 工业制图Industry 工业Inertia 惯性Ink 墨水、油墨Ink holder 钢笔杆China ink 墨汁Inscription 标题Inside diameter 内径Inspection 检修、检查Inspection machine 检修机器Inspector 检查员Installation 装置、设备、安装Installation diagram 安装图Institute 研究所、协会、学院、学会Instruction 说明、指示Instrument 仪器、仪表、工具Instrument drawing 仪器图Intensity 强度Interchangeability 互换性1 Interconnection 互相连接Interference fit 静配合Interior view 内部(的)视图Internal combustion engine 内燃机Internal fillet 内圆角Internal gear 内齿轮Introduction 引言、介绍、序言Invisible line 虚线Involute 渐(伸)开线Involute gear 渐开线齿轮Involute rack 渐开线齿条Involute spline 渐开线花键Involute teeth 渐开线齿形Iron 铁Ingot iron 低碳铁、工业纯铁Knobbled iron 熟铁Magnetic iron 磁铁Malleable iron 可锻铁、韧性铁Plate iron 铁板、钢板Quadrant iron 方钢Rod iron 圆铁、棒钢Round iron 圆铁、圆钢Rustless iron 不锈铁Section iron 型钢Structural iron 结构钢White iron 白口铁Wrought iron 熟铁、锻铁Isometric diagram 等轴测图Isometric drawing 等轴测图Jack-screw 螺旋千斤顶Job sheet 零件图纸Joint 结合、连接、焊接Bolt joint 螺栓连接Riveted joint 铆钉连接Welded joint 焊接Journal 轴径Journal bearing 径向轴承Keeper 保持器(片)、架、定位件卡箍Keep-ring 保持环Key diagram 键、按钮Key way(seat、seating、slot)键槽Key wrench 套筒扳手Gib-head taper key 钩头斜键Square key 方形键Tightening key 斜扁键Woodruff key 半圆键Key-bolt 键螺栓Kilogram(me)公斤、千克Kilogram-meter 公斤米、千克米Kilometer 公里、千米Kilovolt 千瓦Kilowatt 千伏Kit 一套工具Knee 弯头、升降台Knee bend 弯管Knob 捏手、按钮Knuckle thread 圆形螺纹Knurl 滚花、压花Knurled nut滚花螺母L-bar = L-beam 角钢Laboratory 实验室、研究室Lamp 灯Alarm lamp 信号灯Daylight lamp 日光灯Incandescent lamp 白炽灯Indicating lamp 信号灯、指示灯Lantern 游环、套环Large compasses 大圆规Lathe 车床Lathe-hand 车工Lattin = Latten 金属薄板、黄铜片Law 规律、定律Lay 布置、安排、放置Layer 层Carburized layer 渗碳层Layout 计划、方案、草图Layout design 草图设计、方案设计Layout drawing 方案草图Lead angle 螺旋升角Lead line 指引线Leaf spring 板弹簧Left hand 左方向Left hand thread 左旋螺纹Legend 图例、图表符号、代号、说明书Length 长度、距离Length gauge 长度规Length of normal 法线长Length of side 边长Effective length 有效长度Lens 透镜、镜片Letter 字、字母Capital letter 大写字母Level surface 水平面Lift 升降机、电梯Light alloy 轻合金Light beam 光束Light series 轻系列Light-duty 轻型Lighting installation 照明装置Lightning switch 照明开关Liquid 液体Limit 极限尺寸Limit switch 限位开关Line 线Line of action (齿轮)压力线Line of contact (齿轮)接触线Line of shaft轴线Line of thickness 线型的粗度Line weight线的粗细程度Actual line实线Addendum line齿顶线Broken line断裂线Center line = central line中心线Continuous line实线Dash(ed) line虚线Diagonal line 对角线Imaginary line 假想线Generation line 母线Pitch line 节线Real line 实线Reference line 基准线、参考线Right line 直线Skeleton line 轮廓线Solid line 实线Straight line 直线Vertical line 垂直线Liner 衬套Bearing line 轴瓦Link 连接环、链节Line assembly 连杆装配图Chain link 链节L-iron 角铁List 注册、记录、名册、目录Load 符合Actual load 有效载荷、实际载荷Allowable load 容许载荷Full load 满载(荷)、全负载(荷) Local view 局部视图Localization 定位\固定Locating pin 定位销Location by angle 角度定位Location by dimension 定位尺寸Location pin 定位销Location tolerance 定位公差Lock 锁\阀Lock nut 防松螺母Lock screw 锁紧螺钉Lock washer 弹簧垫圈Valve lock 阀簧抵座销、气门制销Loco 机车、火车头Logarithm 对数Long break 长断裂线Long radius 长半径Longitudinal key 长方键Lower limit 下限Lubricant pump 润滑油泵Lubricating ring 润滑油环Lubrication 润滑Bath lubrication 油浴润滑Bearing lubrication 轴承润滑Ring lubrication 油环润滑Shot lubrication 油枪润滑Splash lubrication 飞溅润滑Lubricator 润滑器Lubro-pump 油泵Luminaire 光源Machine 机器、切割Machine building (manufacturing) 机械制造Machine drawing 机械制图Machine finish 机械加工Machine maker 机械工厂(制造者) Machine part 机械零件Machine shop 机工车间Drawing machine 绘图机Tracing machine 描图机Machining allowance 加工余量Machinist 机械工人\机械师Magazine 杂志Magnetic-particle clutch 电磁离合器Magnitude 数量、长度、大小Major type of slotted nut 大型锁母Make 制造、构造Malleable cast iron 可锻铸铁Malleable casting 韧铸件Malleable steel 软钢、展性钢Manual 手册、说明书Manual control 手控Manufacture 加工、制造业Manucturing engineering 制造工艺(技术) Manucturing machine 生产机械Manucturing tolerance 制造公差Master check 校正、校对Master drawing 样图Master gauge 标准规、校准规Master gear 主齿轮、标准齿轮Master making 手工Master screw 标准螺纹Match 匹配、配合Mate 啮合部分Material 物质、材料Fibre material 纤维材料Insulating material 绝缘材料Plastic material 塑料Maximal valve 极大值Maximum 极点、极限、最大量Maximum admitted diameter of work 工件最大许可直径Mean axis 中间轴Measure 量度、大小、尺寸Measure of precision 精确度Measurement 测定、尺寸、大小Measuring device 量具Measuring tools 量具Mechanical bolt 螺钉Mechanical drawing 机械制图Mechanical engineering’s scale 机械工程比例尺Mechanical properties 机械性能Mechanical reduction gear 齿轮减速装置Mechanism 机械结构、机械装置Medium series 中系列Mating member 配合件Meshing gear 啮合齿轮Metal 金属Admiralty metal 含锡黄铜Bell metal 青铜合金、种铜、铜锡合金Brazing metal 铜锌合金Hard metal 硬质合金Heavy metal 重金属Light metal 轻金属Monel metal 铜镍合金Power(ed) metal 粉末合金Wear-resistant metal 耐磨金属White metal 白合金(铅锑锡合金)Yellow metal 黄金、黄色金属Metallized 镀金属的、喷涂金属的Meter 米、公尺。