锐捷交换机命令

合集下载

锐捷交换机常用命令

锐捷交换机常用命令

(3.交换机对已经绑定的IP进行MAC检查,如果不相同,丢弃该帧;对没有绑定的不检查,并照样转发该报文,建议在核心层层使用.
2. 交换机防主机欺骗用功能
S2126#conf
S2126(config)# int g0/23
----进入第23接口,准备在该接口绑定用户的MAC和ip地址
S2126(config-if)# switchport port-security ----开启端口安全功能
S2126(config)#end ----退会特权模式
S2126# wr ----保存配置
注释:可以通过在接口下设置最大的安全地址个数从而来控制控制该接口下可使用的主机数,安全地址的个数跟交换机的硬件资源有关,建议在接入层上使用该项.
S2126(config-if)#switchport port-security maximum 1设置最大mac地址绑定数量,适合该口下只接一台电脑.
S2126(config-if)# switchport port-security mac-address 0016.d390.6cc5 ip-address 172.16.40.101 ----在23端口下绑定ip地址是172.16.40.101 MAC地址是0016.d390.6cc5的主机,确保该主机可以正常使用网络,如果该主机修改ip或者MAC地址则无法使用网络,可以添加多条来实现对接入主机的控制
1.交换机地址绑定(address-bind)功能
S2126#conf
S2126(config)# address-bind 172.16.40.101 0016.d390.6cc5
----绑定ip地址为172.16.40.101 MAC地址为0016.d390.6cc5的主机让其使用网络

(完整版)锐捷交换机命令大全

(完整版)锐捷交换机命令大全

【第一部分】交换机支持的命令:1.交换机基本状态:switch: ;ROM状态,路由器是rommon>hostname> ;用户模式hostname# ;特权模式hostname(config)# ;全局配置模式hostname(config-if)# ;接口状态2.交换机口令设置:switch>enable ;进入特权模式switch#config terminal ;进入全局配置模式switch(config)#hostname;设置交换机的主机名switch(config)#enable secret xxx ;设置特权加密口令switch(config)#enable password xxa ;设置特权非密口令switch(config)#line console 0 ;进入控制台口switch(config-line)#line vty 0 4 ;进入虚拟终端switch(config-line)#login ;允许登录switch(config-line)#password xx ;设置登录口令xxswitch#exit ;返回命令3.交换机VLAN设置:switch#vlan database ;进入VLAN设置switch(vlan)#vlan 2 ;建VLAN 2switch(vlan)#no vlan 2 ;删vlan 2switch(config)#int f0/1 ;进入端口1switch(config-if)#switchport access vlan 2 ;当前端口加入vlan 2 switch(config-if)#switchport mode trunk ;设置为干线switch(config-if)#switchport trunk allowed vlan 1,2 ;设置允许的vlan switch(config-if)#switchport trunk encap dot1q ;设置vlan 中继switch(config)#vtp domain;设置发vtp域名switch(config)#vtp password;设置发vtp密码switch(config)#vtp mode server ;设置发vtp模式switch(config)#vtp mode client ;设置发vtp模式4.交换机设置IP地址:switch(config)#interface vlan 1 ;进入vlan 1switch(config-if)#ip address;设置IP地址switch(config)#ip default-gateway;设置默认网关switch#dir flash: ;查看闪存5.交换机显示命令:switch#write ;保存配置信息switch#show vtp ;查看vtp配置信息switch#show run ;查看当前配置信息switch#show vlan ;查看vlan配置信息switch#show interface ;查看端口信息switch#show int f0/0 ;查看指定端口信息【第二部分】路由器支持的命令:1.路由器显示命令:router#show run ;显示配置信息router#show interface ;显示接口信息router#show ip route ;显示路由信息router#show cdp nei ;显示邻居信息router#reload ;重新起动2.路由器口令设置:router>enable ;进入特权模式router#config terminal ;进入全局配置模式router(config)#hostname;设置交换机的主机名router(config)#enable secret xxx ;设置特权加密口令router(config)#enable password xxb ;设置特权非密口令router(config)#line console 0 ;进入控制台口router(config-line)#line vty 0 4 ;进入虚拟终端router(config-line)#login ;要求口令验证router(config-line)#password xx ;设置登录口令xx router(config)#(Ctrl+z) ;返回特权模式router#exit ;返回命令3.路由器配置:router(config)#int s0/0 ;进入Serail接口router(config-if)#no shutdown ;激活当前接口router(config-if)#clock rate 64000 ;设置同步时钟router(config-if)#ip address;设置IP地址router(config-if)#ip address second ;设置第二个IProuter(config-if)#int f0/0.1 ;进入子接口router(config-subif.1)#ip address;设置子接口IProuter(config-subif.1)#encapsulation dot1q;绑定vlan中继协议router(config)#config-register 0x2142 ;跳过配置文件router(config)#config-register 0x2102 ;正常使用配置文件router#reload ;重新引导4.路由器文件操作:router#copy running-config startup-config ;保存配置router#copy running-config tftp ;保存配置到tftprouter#copy startup-config tftp ;开机配置存到tftprouter#copy tftp flash: ;下传文件到flashrouter#copy tftp startup-config;下载配置文件ROM状态:Ctrl+Break ;进入ROM监控状态rommon>confreg 0x2142 ;跳过配置文件rommon>confreg 0x2102 ;恢复配置文件rommon>reset;重新引导rommon>copy xmodem: flash: ;从console传输文件rommon>IP_ADDRESS=10.65.1.2 ;设置路由器IP rommon>IP_SUBNET_MASK=255.255.0.0 ;设置路由器掩码rommon>TFTP_SERVER=10.65.1.1 ;指定TFTP服务器IP rommon>TFTP_FILE=c2600.bin ;指定下载的文件rommon>tftpdnld ;从tftp下载rommon>dir flash: ;查看闪存内容rommon>boot ;引导IOS5.静态路由:ip route;命令格式router(config)#ip route 2.0.0.0 255.0.0.0 1.1.1.2 ;静态路由举例router(config)#ip route 0.0.0.0 0.0.0.0 1.1.1.2 ;默认路由举例6.动态路由:router(config)#ip routing ;启动路由转发router(config)#router rip ;启动RIP路由协议。

锐捷网络交换机的配置命令集

锐捷网络交换机的配置命令集

锐捷网络交换机的配置命令集交换机>Enable 进入特权模式#Exit 返回上一级操作模式#End 返回到特权模式#write memory 或copy running-config startup-config 保存配置文件#del flash:config.text 删除配置文件(交换机及1700系列路由器)#erase startup-config 删除配置文件(2500系列路由器)#del flash:vlan.dat 删除Vlan配置信息(交换机)#Configure terminal 进入全局配置模式(config)# hostname switchA配置设备名称为switchA(config)#banner motd & 配置每日提示信息&为终止符(config)#enable secret level 1 0 star 配置远程登陆密码为star(config)#enable secret level 15 0 star 配置特权密码为starLevel 1为普通用户级别,可选为1~15,15为最高权限级别;0表示密码不加密(config)#enable services web-server 开启交换机WEB管理功能Services 可选以下:web-server(WEB管理)、telnet-server(远程登陆)等查看信息#show running-config 查看当前生效的配置信息#show interface fastethernet 0/3 查看F0/3端口信息#show interface serial 1/2 查看S1/2端口信息#show interface 查看所有端口信息#show ip interface brief 以简洁方式汇总查看所有端口信息#show ip interface 查看所有端口信息#show version 查看版本信息#show mac-address-table 查看交换机当前MAC地址表信息#show running-config 查看当前生效的配置信息#show vlan 查看所有VLAN信息#show vlan id 10 查看某一VLAN (如VLAN10)的信息#show interface fastethernet 0/1 switchport 查看某一端口模式(如F 0/1)#show aggregateport 1 summary 查看聚合端口AG1的信息#show spanning-tree 查看生成树配置信息#show spanning-tree interface fastethernet 0/1 查看该端口的生成树状态#show port-security 查看交换机的端口安全配置信息#show port-security address 查看地址安全绑定配置信息#show ip access-lists listname 查看名为listname的列表的配置信息#show access-lists端口的基本配置(config)#Interface fastethernet 0/3 进入F0/3的端口配置模式(config)#interface range fa 0/1-2,0/5,0/7-9 进入F0/1、F0/2、F0/5、F0/7、F0/8、F0/9的端口配置模式(config-if)#speed 10 配置端口速率为10M,可选10,100,auto(config-if)#duplex full 配置端口为全双工模式,可选full(全双工),half(半双式),auto(自适应)(config-if)#no shutdown 开启该端口(config-if)#switchport access vlan 10 将该端口划入VLAN10中,用于VLAN(config-if)#switchport mode trunk 将该端口设为trunk模式,用于Tag vlan可选模式为access , trunk(config-if)#port-group 1 将该端口划入聚合端口AG1中,用于聚合端口聚合端口的创建(config)# interface aggregateport 1 创建聚合接口AG1(config-if)# switchport mode trunk 配置并保证AG1为trunk 模式(config)#int f0/23-24(config-if-range)#port-group 1 将端口(端口组)划入聚合端口AG1中生成树(config)#spanning-tree 开启生成树协议(config)#spanning-tree mode stp 指定生成树类型为stp可选模式stp , rstp , mstp(config)#spanning-tree priority 4096 设置交换机的优先级为4096 , 优先级值小为高。

锐捷交换机配置命令

锐捷交换机配置命令

锐捷网络交换机的配置命令集交换机:>Enable 进入特权模式#Exit 返回上一级操作模式#End 返回到特权模式#write memory 或copy running-config startup-config 保存配置文件#del flash:config.text 删除配置文件(交换机及1700系列路由器)#erase startup-config 删除配置文件(2500系列路由器)#del flash:vlan.dat 删除Vlan配置信息(交换机)#Configure terminal 进入全局配置模式(config)# hostname switchA 配置设备名称为switchA(config)#banner motd & 配置每日提示信息 &为终止符(config)#enable secret level 1 0 star 配置远程登陆密码为star(config)#enable secret level 15 0 star 配置特权密码为starLevel 1为普通用户级别,可选为1~15,15为最高权限级别;0表示密码不加密(config)#enable services web-server 开启交换机WEB管理功能Services 可选以下:web-server(WEB管理)、telnet-server(远程登陆)等查看信息:#show running-config 查看当前生效的配置信息#show interface fastethernet 0/3 查看F0/3端口信息#show interface serial 1/2 查看S1/2端口信息#show interface 查看所有端口信息#show ip interface brief 以简洁方式汇总查看所有端口信息#show ip interface 查看所有端口信息#show version 查看版本信息#show mac-address-table 查看交换机当前MAC地址表信息#show running-config 查看当前生效的配置信息#show vlan 查看所有VLAN信息#show vlan id 10 查看某一VLAN (如VLAN10)的信息#show interface fastethernet 0/1 switchport 查看某一端口模式(如F 0/1) #show aggregateport 1 summary 查看聚合端口AG1的信息#show spanning-tree 查看生成树配置信息#show spanning-tree interface fastethernet 0/1 查看该端口的生成树状态#show port-security 查看交换机的端口安全配置信息#show port-security address 查看地址安全绑定配置信息#show ip access-lists listname 查看名为listname的列表的配置信息#show access-lists端口的基本配置:(config)#Interface fastethernet 0/3 进入F0/3的端口配置模式(config)#interface range fa 0/1-2,0/5,0/7-9 进入F0/1、F0/2、F0/5、F0/7、F0/8、F0/9的端口配置模式(config-if)#speed 10 配置端口速率为10M,可选10,100,auto(config-if)#duplex full 配置端口为全双工模式,可选full(全双工),half(半双式),auto(自适应)(config-if)#no shutdown 开启该端口(config-if)#switchport access vlan 10 将该端口划入VLAN10中,用于VLAN(config-if)#switchport mode trunk 将该端口设为trunk模式,用于Tag vlan 可选模式为access , trunk(config-if)#port-group 1 将该端口划入聚合端口AG1中,用于聚合端口聚合端口的创建(config)# interface aggregateport 1 创建聚合接口AG1(config-if)# switchport mode trunk 配置并保证AG1为 trunk 模式(config)#int f0/23-24(config-if-range)#port-group 1 将端口(端口组)划入聚合端口AG1中生成树(config)#spanning-tree 开启生成树协议(config)#spanning-tree mode stp 指定生成树类型为stp可选模式stp , rstp , mstp(config)#spanning-tree priority 4096 设置交换机的优先级为4096 , 优先级值小为高。

锐捷交换机命令

锐捷交换机命令

锐捷交换机配置命令交换机基本操作1.进入特权模式Switch>enableSwitch#2.返回用户模式Switch#exitPress RETURN to get started!Switch>配置模式:全局配置模式[主机名(config)#]:配置交换机的整体参数子模式:1.线路配置模式[主机名(config-line)#]:配置交换机的线路参数2.接口配置模式[主机名(config-if)#]:配置交换机的接口参数1.进入全局配置模式下Switch#configure terminalSwitch(config)#exitSwitch#2.进入线路配置模式Switch(config)#line console 0Switch(config-line)#exitSwitch(config)#3.进入接口配置模式Switch(config)#interface fastEthernet 0/1Switch(config-if)#exitSwitch(config)#从子模式下直接返回特权模式Switch(config-if)#endSwitch#交换机操作帮助特点:1.支持命令简写(按TAB键将命令补充完整)2.在每种操作模式下直接输入“?”显示该模式下所有的命令3.命令空格“?”显示命令参数并对其解释说明4.字符“?”显示以该字符开头的命令5.命令历史缓存: (Ctrl+P)显示上一条命令,(Ctrl+N)显示下一条命令6.错误提示信息交换机显示命令:显示交换机硬件及软件的信息 Switch#show version显示当前运行的配置参数 Switch#show running-config显示保存的配置参数 Switch#show configure常用交换机EXEC命令将当前运行的配置参数复制到flash:Switch#write memoryBuilding configuration...[OK]Switch#清空flash中的配置参数:Switch#delete flash:Switch#交换机重新启动:Switch#reloadSystem configuration has been modified. Save? [yes/no]:nProceed with reload? [confirm]配置交换机主机名:Switch(config)#hostname S2126GS2126G(config)#配置交换机口令:1、配置交换机的登陆密码S2126G(config)#enable secret level 1 0 star“0”表示输入的是明文形式的口令2、配置交换机的特权密码S2126G(config)#enable secret level 15 0 Star“0”表示输入的是明文形式的口令常用交换机配置命令:1、为交换机分配管理IP地址S2126G(config)#interface vlan 1S2126G(config-if)#ip address {IP address} {IP subnetmask}[secondary] 2、将接口启用S2126G(config-if)#no shutdown3、将接口关闭S2126G(config-if)#shutdown4、配置接口速率S2126G(config-if)#speed [10|100|auto]5、配置接口双工模式S2126G(config-if)#duplex [auto|full|half显示接口状态:S2126G#show interfaces测定目的端的可达性:S2126G>ping {IP address}从TFTP服务器下载配置参数:S2126G#copy tftp startup-config管理交换机MAC地址表:1、查看MAC地址表S2126G#show mac-address-table2、配置MAC地址表记录的生存时间(缺省为300秒)S2126G(config)#mac-address-table aging-time <10-1000000>3、查看MAC地址表记录的生存时间S2126G#show mac-address-table aging-timeVLAN的配置:1.添加一个VLANS2126G(config)#vlan <1-4094>S2126G(config-vlan)#2.为VLAN命名(可选)S2126G(config-vlan)#name将交换机端口分配到VLAN1.配置Port VLANSwitch(config-if)#switchport access vlan <1-4094>2.配置Tag VLANSwitch(config-if)#switchport mode trunk1).配置本地(native)VLANSwitch(config-if)#switchport trunk native vlan <1-4094>2).从主干链路中清除VLANSwitch(config-if)#switchport trunk allowed vlan except注:VLAN1不可被清除VLAN的验证:1.显示全部的VLAN:Switch#show vlan2.显示单独的VLAN :Switch#show vlan id <1-4094>将VLAN信息保存到flash中:Switch#write memory从flash中清除VLAN信息:Switch#delete flash:RSTP的配置:1.启用生成树:S2126G(config)#spanning-tree2.配置交换机优先级:S2126G(config)#spanning-tree priority <0-61440>“0”或“4096”的倍数(RSTP BPDU该值后12bit全0)3.配置交换机端口优先级:S2126G(config-if)#spanning-tree port-priority <0-240> “0”或“16”的倍数(RSTP BPDU该值后4bit全0)4、生成树hello时间的配置(由Root决定):S2126G(config)#spanning-tree hello-time <1-10>5、生成树的验证:Switch#show spanning-treeSwitch#show spanning-tree interface <接口名称> <接口编号>以上用于锐捷交换机的。

锐捷交换机配置命令

锐捷交换机配置命令

>Enable 进入特权模式#Exit 返回上一级操作模式#End 返回到特权模式#write memory 或copy running-config startup-config 保存配置文件#del flash:config.text 删除配置文件(交换机及1700系列路由器)#erase startup-config 删除配置文件(2500系列路由器)#del flash:vlan.dat 删除Vlan配置信息(交换机)#Configure terminal 进入全局配置模式(config)# hostname switchA配置设备名称为switchA(config)#banner motd & 配置每日提示信息&为终止符(config)#enable secret level 1 0 star 配置远程登陆密码为star(config)#enable secret level 15 0 star 配置特权密码为starLevel 1为普通用户级别,可选为1~15,15为最高权限级别;0表示密码不加密(config)#enable services web-server 开启交换机WEB管理功能Services 可选以下:web-server(WEB管理)、telnet-server(远程登陆)等查看信息#show running-config 查看当前生效的配置信息#show interface fastethernet 0/3 查看F0/3端口信息#show interface serial 1/2 查看S1/2端口信息#show interface 查看所有端口信息#show ip interface brief 以简洁方式汇总查看所有端口信息#show ip interface 查看所有端口信息#show version 查看版本信息#show mac-address-table 查看交换机当前MAC地址表信息#show running-config 查看当前生效的配置信息#show vlan 查看所有VLAN信息#show vlan id 10 查看某一VLAN (如VLAN10)的信息#show interface fastethernet 0/1 switchport 查看某一端口模式(如F 0/1)#show aggregateport 1 summary 查看聚合端口AG1的信息#show spanning-tree 查看生成树配置信息#show spanning-tree interface fastethernet 0/1 查看该端口的生成树状态#show port-security 查看交换机的端口安全配置信息#show port-security address 查看地址安全绑定配置信息#show ip access-lists listname 查看名为listname的列表的配置信息#show access-lists端口的基本配置(config)#Interface fastethernet 0/3 进入F0/3的端口配置模式(config)#interface range fa 0/1-2,0/5,0/7-9 进入F0/1、F0/2、F0/5、F0/7、F0/8、F0/9的端口配置模式(config-if)#speed 10 配置端口速率为10M,可选10,100,auto(config-if)#duplex full 配置端口为全双工模式,可选full(全双工),half(半双式),auto(自适应)(config-if)#no shutdown 开启该端口(config-if)#switchport access vlan 10 将该端口划入VLAN10中,用于VLAN(config-if)#switchport mode trunk 将该端口设为trunk模式,用于Tag vlan可选模式为access , trunk(config-if)#port-group 1 将该端口划入聚合端口AG1中,用于聚合端口聚合端口的创建(config)# interface aggregateport 1 创建聚合接口AG1(config-if)# switchport mode trunk 配置并保证AG1为trunk 模式(config)#int f0/23-24(config-if-range)#port-group 1 将端口(端口组)划入聚合端口AG1中生成树(config)#spanning-tree 开启生成树协议(config)#spanning-tree mode stp 指定生成树类型为stp可选模式stp , rstp , mstp(config)#spanning-tree priority 4096 设置交换机的优先级为4096 , 优先级值小为高。

锐捷交换机典型配置指令

锐捷交换机典型配置指令

一、密码设置Ruijie> enableRuijie#configuration terminalRuijie(config)# enable password密码Ruijie(config)# line console 0Ruijie(config-line)# password密码Ruijie(config-line)# loginRuijie(config)# line vty 0 4Ruijie(config-line)# password 密码Ruijie(config-line)# login二、设备命名、接口命名、VLAN命名Ruijie> enableRuijie# configuration terminalRuijie(config)# hostname名字Ruijie(config)# interface fastethernet 0/1Ruijie(config-if)# description 接口描述内容Ruijie(config)# vlan vlan编号Ruijie(config-vlan)#name名字二、POE供电的配置及查看Ruijie> enableRuijie# configuration terminalRuijie(config)# interface fastethernet 0/1Ruijie(config-if)# poe enableRuijie(config)# interface range fastethernet 0/1 - 24Ruijie(config- if -range)# poe enableRuijie# show poe interface 接口编号Ruijie# show poe powersupply三、接口模式设置、速率、双工、光电模式转换Ruijie# configuration terminalRuijie(config)# interface fastethernet 0/1Ruijie(config-if)# medium-type { fiber | copper } Ruijie(config-if)# speed {10 | 100 | 1000 | auto } Ruijie(config-if)# duplex {auto | full | half }四、设备配置保存、备份、删除、重启Ruijie> enableRuijie# writeRuijie# copy flash:/config.text xmodemRuijie# delete config.textRuijie# reload五、设备管理IP及SNMP团体属性配置Ruijie# configuration terminalRuijie(config)# interface vlan 管理vlan编号Ruijie(config-if)# ip address ip地址子网掩码Ruijie(config)# snmp community string ro六、基于时间的访问控制列表Ruijie> enableRuijie# clock set hh:mm:ss month day yearRuijie# configuration terminalRuijie(config)# ntp server x.x.x.xRuijie(config)# time-range time-range-nameRuijie(config-time-range)# periodic weekdays 8:00 to 18:00Ruijie(config)# ip access-list extended 100Ruijie(config-ext-nacl)# permit ip any any time-range time-range-name Ruijie(config)# interface gigabitEthernet 0/1Ruijie(config-if)# ip access-group 100 in。

锐捷交换机、路由器常用命令

锐捷交换机、路由器常用命令

锐捷交换机、路由器常用命令锐捷交换机、路由器常用命令EXEC模式:用户模式switch>交换机信息的查看,简单测试命令特权模式switch#查看、管理交换机配置信息,测试、调试配置模式:全局配置模式switch(config)#配置交换机的整体参数接口配置模式switch(config-if)#配置交换机的接口参数进入全局配置模式Switch#c onfigure terminalSwitch(config)#exitSwitch#进入接口配置模式Switch(config)#interface fastethernet 0/1 Switch(config-if)#exitSwitch(config)#从子模式下直接返回特权模式Switch(config-if)#endSwitch#命令行其他功能获得帮助switch#?switch#show ?命令简写全写:switch# configure terminal简写:Switch# config使用历史命令Switch# (向上键)Switch# (向下键)配置交换机T elnet功能配置远程登陆密码Switch(config)#enable secret level 1 0 ruijie 配置进入特权模式密码Switch (config)#enable secret level 15 0 ruijie为交换机配置管理IPSwitch (config)#interface vlan 1Switch (config-if)#no shutdownSwitch (config-if)#ip address 192.168.1.1 255.255.255.0 Switch (config-if)#end配置文件的管理保存配置将当前运行的参数保存到flash 中用于系统初始化时初始化参数Switch#copy running-config startup-configSwitch#write memorySwitch#write删除配置永久性的删除flash 中不需要的文件使用命令delete flash:config.text删除当前的配置:在配置命令前加no例:switch(config-if)# no ip address查看配置文件内容Switch#show configure 查看保存在FLASH里的配置信息Switch#show running-config 查看RAM里当前生效的配置配置Port VLAN创建VLAN10,将它命名为test的例子Switch# configure terminalSwitch(config)# vlan 10Switch(config-vlan)# name testSwitch(config-vlan)# end把接口 0/10加入VLAN10Switch# configure terminalSwitch(config)# interface fastethernet 0/10Switch(config-if)# switchport mode accessSwitch(config-if)# switchport access vlan 10Switch(config-if)# end将一组接口加入某一个VLANSwitch(config)#interface range fastethernet 0/1-8,0/15,0/20Switch(config-if-range)# switchport access vlan 20注:连续接口0/1-8,不连续接口用逗号隔开,但一定要写明模块编号配置Tag VLAN-Trunk把Fa0/1配成Trunk口Switch# configure terminalSwitch(config)# interface fastethernet0/1Switch(config-if)# switchport mode trunk把端口Fa0/20 配置为Trunk端口,但是不包含VLAN 2:Switch(config)# interface fastethernet 0/20Switch(config-if)# switchport trunk allowed vlan remove 2 Switch(config-if)# endNative VLAN配置命令:Switch(config-if)# switchport trunk native vlan 20 Switch(config-if)# end注意:每个Trunk口的缺省native VLAN是VLAN 1在配置Trunk链路时,请确保连接链路两端的Trunk口属于相同的native VLAN保存/清除VLAN信息将VLAN信息保存到flash中Switch#write memory从flash中只清除VLAN信息Switch#delete flash:vlan.dat从RAM中删除VLANSwitch(config)#no vlan VLAN-id生成树协议的配置开启生成树协议Switch(config)#Spanning-tree关闭生成树协议Switch(config)#no Spanning-tree配置生成树协议的类型Switch(config)#Spanning-tree mode stp/rstp锐捷全系列交换机默认使用MSTP协议配置交换机优先级Switch(config)#spanning-tree priority <0-61440>(“0”或“4096”的倍数、共16个、缺省32768)恢复到缺省值Switch(config)# no spanning-tree priority配置交换机端口的优先级Switch(config)#interface interface-type interface-numberSwitch(config-if)#spanning-tree port-priority number配置STP、RSTPSpanning Tree 的缺省配置:关闭STPSTP Priority 是32768STP port Priority 是128STP port cost 根据端口速率自动判断Hello Time 2秒Forward-delay Time 15秒Max-age Time 20秒可通过spanning-tree reset 命令让spanning tree参数恢复到缺省配置查看生成树协议配置显示生成树状态Switch#show spanning-tree显示端口生成树协议的状态Switch#show spanning-tree interface fastethernet <0-2/1-24> 配置aggregate port将该接口加入一个APSwitch#c onfigure terminalSwitch(config) # interface interface-type interface-idSwitch(config-if-range)#port-group port-group-number如果这个AP不存在,可自动创建AG端口查看聚合端口的汇总信息Switch#show aggregateport summary查看聚合端口的流量平衡方式Switch#show aggregateport load-balance路由器上配置telnet第一步: 配置端口地址RouterA# configure terminal !进入全局配置模式RouterA(config)# interface fastethernet 1/0!进入路由器接口配置模式RouterA(config-if)# ip address 192.168.0.1 255.255.255.0!配置路由器管理接口IP地址RouterA(config-if)# no shutdown !开启路由器 f 1/0接口第二步:配置远程登录密码RouterA(config)# line vty 0 4 !进入路由器线路配置模式RouterA(config-line)# login !配置远程登录RouterA(config-line)# password star !设置路由器远程登录密码为“star”RouterA(config-line)#end第三步:配置路由器特权模式密码RouterA(config)# enable secret star !设置路由器特权模式密码为“star”或者RouterA(config)# enable password star查看配置文件show version !查看版本及引导信息show running-config !查看运行配置show startup-config !查看用户保存在NVRAM中的配置文件保存配置文件Router#copy running-config startup-configRouter#write memoryRouter#write删除配置文件Router#delete flash:config.text !删除初始配置文件查看路由信息router#show ip routeCodes: C - connected,S – static, R – RIP, O- OSPF IA - OSPF inter area,E1-OSPF external type 1E2 - OSPF external type 2,* - candidate default Gateway of last resort is 10.5.5.5 to network 0.0.0.0 172.16.0.0/24 is subnetted, 1 subnetsC 172.16.11.0 is directly connected, serial1/2O E2 172.22.0.0/16 [110/20] via 10.3.3.3, 01:03:01, Serial1/2S* 0.0.0.0/0 [1/0] via 10.5.5.5静态路由配置命令配置静态路由用命令ip routerouter(config)#ip route [网络编号] [子网掩码] [转发路由器的IP 地址/本地接口]例:ip route 192.168.10.0 255.255.255.0 serial 1/2 例:ip route 192.168.10.0 255.255.255.0 172.16.2.1静态路由描述转发路径的方式有两种指向本地接口(即从本地某接口发出)指向下一跳路由器直连接口的IP地址(即将数据包交给X.X.X.X)配置默认路由:router(config)#ip route 0.0.0.0 0.0.0.0 [转发路由器的IP 地址/本地接口]RIP路由协议的版本RIPv1有类路由协议,不支持VLSM以广播的形式发送更新报文不支持认证RIPv2无类路由协议,支持VLSM以组播的形式发送更新报文支持明文和MD5的认证配置RIP协议配置步骤1、开启RIP路由协议进程Router(config)#router rip2、申请本路由器参与RIP协议的直连网段信息Router(config-router)#network 192.168.1.03、指定RIP协议的版本2(默认是version1) Router(config-router)#version 24、在RIPv2版本中关闭自动汇总Router(config-router)#no auto-summary查看RIP配置信息验证 RIP的配置Router#show ip protocols显示路由表的信息Router#show ip route清除 IP路由表的信息Router#clear ip route在控制台显示 RIP的工作状态Router#debug ip ripOSPF协议OSPF配置如下:1、创建loopback接口,定义ROUTE IDrouterA(config)#interface loopback 10routerA(config)#ip address 192.168.100.1 255.255.255.0 2、开启OSPF进程routerA(config)#router ospf 1010代表进程编号,只具有本地意义3、申请直连网段routerA(config-router)#network 10.1.1.0 0.0.0.255 area 0 注意反掩码和区域号查看OSPF配置信息验证 OSPF的配置Router#show ip ospf显示路由表的信息Router#show ip route清除 IP路由表的信息Router#clear ip route在控制台显示 OSPF的工作状态Router#debug ip ospf三层交换的路由功能三层交换机默认开启路由功能Switch(config)#ip routing (开启三层交换机路由功能)三层交换机配置路由接口的两种方法开启三层交换机物理接口的路由功能Switch(config)#interface fastethernet 0/5Switch(config-if)#no switchportSwitch(config-if)#ip address 192.168.1.1 255.255.255.0 Switch(config-if)#no shutdown关闭物理接口路由功能Switch(config-if)# switchport采用SVI方式(switch virtual interface)Switch(config)#interface vlan 10Switch(config-if)#ip address 192.168.1.1.255 255.255.0 Switch(config-if)#no shutdown三层交换机和路由器相连的网络方法一(SVI):Switch(config)#interface f0/10Switch(config-if)#switchport access vlan 10Switch(config-if)#exitSwitch(config)#interface vlan 10 switch(config-if)#ip address 192.168.10.1 255.255.255.0Switch(config-if)#no shutdown方法二(路由接口):Switch(config)#interface f0/10Switch(config-if)#no switchportSwitch(config-if)#ip address 192.168.10.1 255.255.255.0 Switch(config-if)#no shutdown三层交换机路由协议的配置静态路由Switch(config)#ip route x.x.x.x x.x.x.x [x.x.x.x/interface] RIPSwitch(config)#router ripSwitch(config-router)#network X.X.X.XSwitch(config-router)#version 2注:三层交换机不支持no auto-summaryOSPFSwitch(config)#router ospfSwitch(config)#network X.X.X.X X.X.X.X area x查看三层交换机路由配置查看路由接口信息Switch#show ip interface。

锐捷交换机常用配置命令详解

锐捷交换机常用配置命令详解
方式二:XMODEM的升级方式
交换机升级
*
方式二:XMODEM的升级方式 要升级的软件版本与当前运行版本有一定的要求时,可以通过XMODEM方式来进行升级。 步骤:主机的配置接口和PC机的串口相连接,并把超级终端速率设置为57600重新启动交换机后不断按ESC键,直到出现以下界面 TOOLS MENU ***************************************************** ******* 1 -- Download ****** ******* 2 -- Upload ****** ******* 3 -- File Info ****** ******* 4 -- Delete File ****** ******* 5 -- Rename File ****** ******* 6 -- Run Main File ****** ******* 7 -- Format Flash ****** ******* 8 -- Defrag Flash ****** ******* 9 -- download all files(DHCP + TFTP)****** ***************************************************** Input command:
*
锐捷网络使用培训
BRAND PLANING
内部材料
*
培训内容
CONTENTS
01
交换机的配置命令
03
GSN相关配置
02
SAM相关配置
交换机的配置培训
*
交换机的密码配置
如何清除密码
交换机的VLAN配置
交换机升级
交换机防病毒访问控制列表

锐捷交换机配置命令大全

锐捷交换机配置命令大全

锐捷交换机配置命令一、交换机基本配置交换机命名:在项目实施的时候,建议为处于不同位置的交换机命名,便于记忆,可提高后期管理效率。

switch(config)#hostname ruijie //ruijie为该交换机的名字交换机配置管理密码:配置密码可以提高交换机的安全性,另外,telnet登录交换机的时候,必须要求有telnet管理密码。

switch (config)#enable secret level 1 0 rg //配置telnet管理密码为rg,其中1表示telnet密码,0表示密码不加密switch (config)#enable secret level 15 0 rg //配置特权模式下的管理密码rg,其中15表示为特权密码交换机配置管理IPswitch (config)#interface vlan 1 //假设管理VLAN为VLAN 1switch (config-if)#ip address 192.168.1.1 255.255.255.0 //给管理VLAN配置管理IP地址switch (config-if)#no shutdown //激活管理IP,养成习惯,无论配置什么设备,都使用一下这个命令交换机配置网关:switch(config)#ip default-gateway 192.168.1.254 //假设网关地址为192.168.1.254,此命令用户二层设备。

通过以上几个命令的配置,设备便可以实现远程管理,在项目实施时(尤其是设备位置比较分散)特别能提高效率。

1.1 接口介质类型配置锐捷为了降低SME客户的总体拥有成本,推出灵活选择的端口形式:电口和光口复用接口,方便用户根据网络环境选择对应的介质类型。

但光口和电口同时只能用其一,如图1,如使用了光口1F,则电口1不能使用。

接口介质类型的转换:Switch(config)#interface gigabitethernet 0/1Switch(config-if)#medium-type fiber //把接口工作模式改为光口Switch(config-if)#medium-type copper //把接口工作模式改为电口默认情况下,接口是工作在电口模式在项目实施中,如果光纤模块指示灯不亮,工作模式是否正确也是故障原因之一。

锐捷交换机的配置命令大全

锐捷交换机的配置命令大全

锐捷交换机的配置命令大全很多朋友多次提到锐捷交换机的配置,关于华为与H3C交换机的配置我们之前曾多次提到过,本期我们来了解锐捷交换机的配置。

一、基础配置命令1、准备命令>Enable 进入特权模式#Exit 返回上一级操作模式#End 返回到特权模式#write memory 或copy running-config startup-config 保存配置文件#del flash:config.text 删除配置文件(交换机及1700系列路由器)#erase startup-config 删除配置文件(2500系列路由器)#del flash:vlan.dat 删除Vlan配置信息(交换机)#Configure terminal 进入全局配置模式(config)# hostname switchA 配置设备名称为switchA(config)#banner motd & 配置每日提示信息 &为终止符(config)#enable secret level 1 0 star 配置远程登陆密码为star (config)#enable secret level 15 0 star 配置特权密码为starLevel 1为普通用户级别,可选为1~15,15为最高权限级别;0表示密码不加密(config)#enable services web-server 开启交换机WEB管理功能Services 可选以下:web-server(WEB管理)、telnet-server(远程登陆)等2、查看信息#show running-config //查看当前生效的配置信息#show interface fastethernet 0/3 //查看F0/3端口信息#show interface serial 1/2 //查看S1/2端口信息#show interface //查看所有端口信息#show ip interface brief //以简洁方式汇总查看所有端口信息#show ip interface //查看所有端口信息#show version //查看版本信息#show mac-address-table //查看交换机当前MAC地址表信息#show running-config //查看当前生效的配置信息#show vlan //查看所有VLAN信息#show vlan id 10 //查看某一VLAN (如VLAN10)的信息#show interface fastethernet 0/1 //查看某一端口模式(如F 0/1)#show aggregateport 1 summary //查看聚合端口AG1的信息#show spanning-tree //查看生成树配置信息#show spanning-tree interface fastethernet 0/1 //查看该端口的生成树状态#show port-security //查看交换机的端口安全配置信息#show port-security address //查看地址安全绑定配置信息#show ip access-lists listname //查看名为listname的列表的配置信息3、端口的基本配置(config)#Interface fastethernet 0/3 //进入F0/3的端口配置模式(config)#interface range fa 0/1-2,0/5,0/7-9 //进入F0/1、F0/2、F0/5、F0/7、F0/8、F0/9的端口配置模式(config-if)#speed 10 //配置端口速率为10M,可选10,100,auto(config-if)#duplex full //配置端口为全双工模式,可选full(全双工),half(半双式),auto(自适应)(config-if)#no shutdown //开启该端口(config-if)#switchport access vlan 10 //将该端口划入VLAN10中,用于VLAN(config-if)#switchport mode trunk //将该端口设为trunk模式,可选模式为access , trunk(config-if)#port-group 1 //将该端口划入聚合端口AG1中,用于聚合端口4、聚合端口的创建(config)# interface aggregateport 1 //创建聚合接口AG1(config-if)# switchport mode trunk //配置并保证AG1为trunk 模式(config)#int f0/23-24(config-if-range)#port-group 1 //将端口(端口组)划入聚合端口AG1中5、生成树配置多生成树协议:switch(config)#spanning-tree //开启生成树协议switch(config)#spanning-tree mst configuration //建立多生成树协议switch(config-mst)#name ruijie //命名为ruijieswitch(config-mst)#revision 1 //设定校订本为1switch(config-mst)#instance 0 vlan 10,20 //建立实例0switch(config-mst)#instance 1 vlan 30,40 //建立实例1switch(config)#spanning-tree mst 0 priority 4096 //设置优先级为4096switch(config)#spanning-tree mst 1 priority 8192 //设置优先级为8192switch(config)#interface vlan 10switch(config-if)#vrrp 1 ip 192.168.10.1 //此为vlan 10的IP地址switch(config)#interface vlan 20switch(config-if)#vrrp 1 ip 192.168.20.1 //此为vlan 20的IP地址switch(config)#interface vlan 30switch(config-if)#vrrp 2 ip 192.168.30.1 //此为vlan 30的IP地址(另一三层交换机)switch(config)#interface vlan 40switch(config-if)#vrrp 2 ip 192.168.40.1 //此为vlan 40的IP地址(另一三层交换机)6、VLAN的基本配置(config)#vlan 10 //创建VLAN10(config-vlan)#name vlanname // 命名VLAN为vlanname(config-if)#switchport access vlan 10 //将该端口划入VLAN10中某端口的接口配置模式下进行(config)#interface vlan 10 //进入VLAN 10的虚拟端口配置模式(config-if)# ip address 192.168.1.1 255.255.255.0 //为VLAN10的虚拟端口配置IP及掩码,二层交换机只能配置一个IP,此IP是作为管理IP使用,例如,使用T elnet的方式登录的IP地址(config-if)# no shutdown //启用该端口7、端口安全(config)# interface fastethernet 0/1 //进入一个端口(config-if)# switchport port-security //开启该端口的安全功能a、配置最大连接数限制(config-if)# switchport port-secruity maxmum 1 //配置端口的最大连接数为1,最大连接数为128(config-if)# switchport port-secruity violation shutdown//配置安全违例的处理方式为shutdown,可选为protect (当安全地址数满后,将未知名地址丢弃)、restrict(当违例时,发送一个Trap通知)、shutdown(当违例时将端口关闭,并发送Trap通知,可在全局模式下用errdisable recovery来恢复)b、IP和MAC地址绑定(config-if)#switchport port-security mac-address xxxx.xxxx.xxxx ip-address 172.16.1.1//接口配置模式下配置MAC地址xxxx.xxxx.xxxx和IP172.16.1.1进行绑定(MAC地址注意用小写)8、三层路由功能(针对三层交换机)(config)# ip routing //开启三层交换机的路由功能(config)# interface fastethernet 0/1(config-if)# no switchport //开启端口的三层路由功能(这样就可以为某一端口配置IP)(config-if)# ip address 192.168.1.1 255.255.255.0(config-if)# no shutdown9、三层交换机路由协议(config)# ip route 172.16.1.0 255.255.255.0 172.16.2.1 //配置静态路由注:172.16.1.0 255.255.255.0 为目标网络的网络号及子网掩码172.16.2.1 为下一跳的地址,也可用接口表示,如ip route 172.16.1.0 255.255.255.0 serial 1/2(172.16.2.0所接的端口)(config)# router rip //开启RIP协议进程(config-router)# network 172.16.1.0 //申明本设备的直连网段信息(config-router)# version 2 //开启RIP V2,可选为version 1(RIPV1)、version 2(RIPV2)(config-router)# no auto-summary //关闭路由信息的自动汇总功能(只有在RIPV2支持)(config)# router ospf //开启OSPF路由协议进程(针对1762,无需使用进程ID)(config)# router ospf 1 //开启OSPF路由协议进程(针对2501,需要加OSPF进程ID)(config-router)# network 192.168.1.0 0.0.0.255 area 0//申明直连网段信息,并分配区域号(area0为骨干区域)10、IP ACL:交换机采用命名的访问控制列表;分标准(stand)和扩展(extended)两种a、标准ACL(config)#ip access-list stand listname //定义命名标准列表,命名为listname,stand为标准列表(config-std-nacl)#deny 192.168.30.0 0.0.0.255 //拒绝来自192.168.30.0网段的IP流量通过注:deny:拒绝通过;可选:deny(拒绝通过)、permit(允许通过)192.168.30.0 0.0.0.255:源地址及源地址通配符;可使用any表示任何IP(config-std-nacl)#permit any(config-std-nacl)#end //返回b、扩展ACL(config)#ip access-list extended listname//定义命名扩展列表,命名为listname,extended为扩展(config-ext-nacl)#deny tcp 192.168.30.0 0.0.0.255 192.168.10.0 0.0.0.255 eq www //拒绝源地址为192.168.30.0网段的IP访问目的地址为192.168.10.0网段的WWW服务注:deny:拒绝通过,可选:deny(拒绝通过)、permit(允许通过)tcp: 协议名称,协议可以是udp, ip,eigrp, gre, icmp, igmp, igrp等等。

锐捷交换机配置命令

锐捷交换机配置命令

锐捷交换机配置命令交换机基本操作:1.进入特权模式Switch>enableSwitch#2.返回用户模式Switch#exit子模式1.2.1.2.3.Switch(config-if)#exitSwitch(config)#从子模式下直接返回特权模式Switch(config-if)#endSwitch#交换机操作帮助:1.支持命令简写(按TAB键将命令补充完整)2.在每种操作模式下直接输入“?”显示该模式下所有的命令3.命令空格“?”显示命令参数并对其解释说明4.“字符?”显示以该字符开头的命令5.命令历史缓存:(Ctrl+P)显示上一条命令,(Ctrl+N)显示下一条命令6.错误提示信息交换机显示命令:显示交换机硬件及软件的信息Switch#showversion1.[OK]2.清空3.4.S2126G-1(config)#5.配置交换机口令:1)配置交换机的登陆密码S2126G(config)#enablesecretlevel10star“0”表示输入的是明文形式的口令2)配置交换机的特权密码S2126G(config)#enablesecretlevel150star“0”表示输入的是明文形式的口令常用交换机配置命令:1、为交换机分配管理IP地址S2126G(config)#interfacevlan1S2126G(config-if)#ipaddress{IPaddress}{IPsubnetmask}[secondary] 2、将接口启用S2126G(config-if)#noshutdown345从TFTP1、查看2、配置3、查看MAC地址表记录的生存时间S2126G#showmac-address-tableaging-timeVLAN的配置:1.添加一个VLANS2126G(config)#vlan<1-4094>S2126G(config-vlan)#2.为VLAN命名S2126G(config-vlan)#name名字将交换机端口分配到VLAN1.配置PortVLANSwitch(config-if)#switchportaccessvlan<1-4094>2.配置TagVLANSwitch(config-if)#switchportmodetrunk1)配置本地(native)VLAN2注34VLAN1.2.将VLAN从RSTP1.启用生成树:S2126G(config)#spanning-tree2.配置交换机优先级:S2126G(config)#spanning-treepriority<0-61440>“0”或“4096”的倍数(RSTPBPDU该值后12bit全0)3.配置交换机端口优先级:S2126G(config-if)#spanning-treeport-priority<0-240>“0”或“16”的倍数(RSTPBPDU该值后4bit全0)4、生成树hello时间的配置(由Root决定):S2126G(config)#spanning-treehello-time<1-10>5、生成树的验证:Switch#showspanning-treeSwitch#showspanning-treeinterface<接口名称><接口编号>聚合端口的创建:Switch(config)#interfaceaggregateport1创建聚合接口AG1优先SVIIP,此IP1)配置最大连接数限制Switch(config-if)#switchportport-secruitymaxmum1配置端口的最大连接数为1,最大连接数为128Switch(config-if)#switchportport-secruityviolationshutdown配置安全违例的处理方式为shutdown,可选为protect(当安全地址数满后,将未知名地址丢弃)、restrict(当违例时,发送一个Trap通知)、shutdown(当违例时将端口关闭,并发送Trap通知,可在全局模式下用errdisablerecovery来恢复)2)IP和MAC地址绑定Switch(config-if)#switchportport-securitymac-addressip-address 与IP地址十六进制a-f用小写字母)三层交换机路由功能:1)开启三层交换机的路由功能Switch(config)#iprouting2)开启端口的三层路由功能。

锐捷交换机配置命令

锐捷交换机配置命令

锐捷交换机配置命令1、配置Telnet。

1.1)、enable 进⼊特权模式。

1.2)、configure terminal 进⼊全局配置模式。

1.3)、line vty 0 4 配置远程登陆线路,0~4是远程登陆的线段编号。

1.4)、Login ⽤于打开登陆认证功能。

1.5)、Login local。

1.6)、username admin password 123456 设置⽤户名是admin,登陆密码是123456。

1.7)、en secret 123456 配置的⼝令在配置⽂件中是⽤安全加密的⽅式进⾏存储。

2、常⽤命令。

2.1)、exit 返回上⼀级。

2.2)、end 返回到特权模式。

2.3)、write memory 保存命令(特权模式下执⾏) 2.4)、del config.text 恢复出⼚设置(全局配置模式下执⾏) 2.5)、reload 保存(特权模式下执⾏) 2.6)、show arp 查看设备的IP地址和Mac对应的关系。

3、创建Vlan,为Vlan 设置IP地址。

3.1)、Vlan 50 创建⼀个vlan 50 3.2)、name Vlan50 将创建好的Vlan命名为Vlan50 3.3)、interface vlan 50 进⼊Vlan 50中。

3.4)、ip adress 192.168.1.250 255.255.255.0 设置登陆IP地址。

3.5)、no vlan 50 删除vlan。

4、端⼝基本操作。

4.1)、interface fastethernet 0/4 进⼊端⼝配置模式,也可写成int f0/4。

4.2)、no shutdown 开启端⼝(默认是开启的,⼀般不写这⾏代码)。

4.3)、switchport access vlan 50 将端⼝4加⼊到vlan 50中。

4.3)、no switchport access vlan 将端⼝划回默认valn1中(从Vlan50中删除掉了)。

锐捷交换机命令大全

锐捷交换机命令大全

锐捷交换机命令大全【第一部分】交换机支持的命令:1.交换机基本状态:switch: ;ROM状态,路由器是rommon>hostname> ;用户模式hostname# ;特权模式hostname(config)# ;全局配置模式hostname(config-if)# ;接口状态2.交换机口令设置:switch>enable ;进入特权模式switch#config terminal ;进入全局配置模式switch(config)#hostname;设置交换机的主机名switch(config)#enable secret xxx ;设置特权加密口令switch(config)#enable password xxa ;设置特权非密口令switch(config)#line console 0 ;进入控制台口switch(config-line)#line vty 0 4 ;进入虚拟终端switch(config-line)#login ;允许登录switch(config-line)#password xx ;设置登录口令xxswitch#exit ;返回命令3.交换机VLAN设置:switch#vlan database ;进入VLAN设置switch(vlan)#vlan 2 ;建VLAN 2switch(vlan)#no vlan 2 ;删vlan 2switch(config)#int f0/1 ;进入端口1switch(config-if)#switchport access vlan 2 ;当前端口加入vlan 2 switch(config-if)#switchport mode trunk ;设置为干线switch(config-if)#switchport trunk allowed vlan 1,2 ;设置允许的vlan switch(config-if)#switchport trunk encap dot1q ;设置vlan 中继switch(config)#vtp domain;设置发vtp域名switch(config)#vtp password;设置发vtp密码switch(config)#vtp mode server ;设置发vtp模式switch(config)#vtp mode client ;设置发vtp模式4.交换机设置IP地址:switch(config)#interface vlan 1 ;进入vlan 1switch(config-if)#ip address;设置IP地址switch(config)#ip default-gateway;设置默认网关switch#dir flash: ;查看闪存5.交换机显示命令:switch#write ;保存配置信息switch#show vtp ;查看vtp配置信息switch#show run ;查看当前配置信息switch#show vlan ;查看vlan配置信息switch#show interface ;查看端口信息switch#show int f0/0 ;查看指定端口信息【第二部分】路由器支持的命令:1.路由器显示命令:router#show run ;显示配置信息router#show interface ;显示接口信息router#show ip route ;显示路由信息router#show cdp nei ;显示邻居信息router#reload ;重新起动2.路由器口令设置:router>enable ;进入特权模式router#config terminal ;进入全局配置模式router(config)#hostname;设置交换机的主机名router(config)#enable secret xxx ;设置特权加密口令router(config)#enable password xxb ;设置特权非密口令router(config)#line console 0 ;进入控制台口router(config-line)#line vty 0 4 ;进入虚拟终端router(config-line)#login ;要求口令验证router(config-line)#password xx ;设置登录口令xx router(config)#(Ctrl+z) ;返回特权模式router#exit ;返回命令3.路由器配置:router(config)#int s0/0 ;进入Serail接口router(config-if)#no shutdown ;激活当前接口router(config-if)#clock rate 64000 ;设置同步时钟router(config-if)#ip address;设置IP地址router(config-if)#ip address second ;设置第二个IProuter(config-if)#int f0/0.1 ;进入子接口router(config-subif.1)#ip address;设置子接口IProuter(config-subif.1)#encapsulation dot1q;绑定vlan中继协议router(config)#config-register 0x2142 ;跳过配置文件router(config)#config-register 0x2102 ;正常使用配置文件router#reload ;重新引导4.路由器文件操作:router#copy running-config startup-config ;保存配置router#copy running-config tftp ;保存配置到tftprouter#copy startup-config tftp ;开机配置存到tftprouter#copy tftp flash: ;下传文件到flashrouter#copy tftp startup-config;下载配置文件ROM状态:Ctrl+Break ;进入ROM监控状态rommon>confreg 0x2142 ;跳过配置文件rommon>confreg 0x2102 ;恢复配置文件rommon>reset;重新引导rommon>copy xmodem: flash: ;从console传输文件rommon>IP_ADDRESS=10.65.1.2 ;设置路由器IPrommon>IP_SUBNET_MASK=255.255.0.0 ;设置路由器掩码rommon>TFTP_SERVER=10.65.1.1 ;指定TFTP服务器IP rommon>TFTP_FILE=c2600.bin ;指定下载的文件rommon>tftpdnld ;从tftp下载rommon>dir flash: ;查看闪存内容rommon>boot ;引导IOS5.静态路由:ip route;命令格式router(config)#ip route 2.0.0.0 255.0.0.0 1.1.1.2 ;静态路由举例router(config)#ip route 0.0.0.0 0.0.0.0 1.1.1.2 ;默认路由举例6.动态路由:router(config)#ip routing ;启动路由转发router(config)#router rip ;启动RIP路由协议。

锐捷系列交换机常用配置的命令

锐捷系列交换机常用配置的命令

锐捷常用命令交换机基本命令switch>enable !从用户模式进入特权模式switch # configure terminal !从特权模式进入全局配置模式switch (config)# hostname SwitchA !设置交换机名称为为“SwitchA”SwitchA (config)# enable secret level 1 0 star 设置交换机远程登陆telnet口令SwitchA (config)# enable secret level 15 0 star 将交换机特权模式口令配置为“star”SwitchA (config)# interface vlan 1 !进入交换机管理接口配置模式SwitchA (config-if)#ip address 172.16.0.1 255.255.255.0 配置交换机的IP地址SwitchA (config-if)# no shutdown ! 启用端口S2150G(config)#ip default-gateway 192.168.1.254 //配置网关地址为192.168.1.254S2150G(config)#interface range f 1/0/1-48,2/0/1-48S2150G(config-if) #spanning-tree bpdufilter enabled//将上联光纤口启动过滤Bpdu报文功能,提高网络的稳定性S2150G(config-if)#spanning-tree bpdufilter disabled //禁用Bpdu过滤功能S2150G(config) #snmp-server community public ro //给交换机启动SNMP协议,便于StarView网管工具发现SwitchA # show ip interface 显示三层IP接口的各个属性SwitchA #show mac-address-table 显示交换机MAC地址表的记录SwitchA# show running-config 查看交换机的当前配置SwitchA#show interface fastethernet 0/1 该命令查看接口设置和统计信息SwitchA# copy running-config startup-config 或SwitchA# write memory 保存配置Delete flash:config.text !清除配置文件Delete flash:vlan.dat !删除VLAN配置文件虚拟局域网VLAN配置S2126G(config)# vlan 10 !创建vlan 10S2126G(config-vlan)# name test10 !将Vlan 10命名为test10S2126G(config-vlan)# exit !返回交换机全局配置模式S2126G(config)# interface fastethernet 0/1 !进入F0/1的接口配置模式S2126G(config-if)# switch access vlan 10 !将F0/1端口加入vlan 10中S2126G(config-if)#exitS2126G(config)# interface range fastEthernet 0/2-3 , 0/5S3550(config-if-range)# switch access vlan 10S3550(config)# interface vlan 20 ! 创建虚拟接口vlan 20S3550(config-if)# ip address 172.16.10.254 255.255.255.0 配置虚拟接口vlan 20的IP地址S3550(config-if)# no shutdown !启用端口S2126# show vlan !该命令显示VLAN的成员端口等信息S3550# show vlan id 10 !验证配置配置交换机之间的Trunk连接:注意S3550和S2126均需配置S3550(config)# interface fastEthernet 0/1 !进入F0/1接口配置模式S3550(config-if)# switchport mode trunk !将F0/1设置为Trunk模式S3550# show interface fastEthernet 0/1 switchport链路聚合S3550(config)# interface range fastEthernet 0/1-2 !使用该命令同时配置多个接口S3550(config-if-range)#port-group 1 !配置F0/1和F0/2归属于AG1S3550(config-if-range)#endS3550# show aggregateport 1 summary !显示聚合端口AG1摘要信息S3550(config)# interface aggregatePort 1 !进入AG1接口模式S3550(config-if)# switchport mode trunk !将端口设为tag vlan模式S3550(config-if)# endS3550(config)# ip routing !启动路由功能生成树SwitchA(config)# spanning-tree ! 开启生成树协议SwitchA(config)# spanning-tree mode stp ! 设置生成树为STP(802.1D)SwitchA (config)# spanning-tree priority 4096 配置SwitchA为根交换机即将SwitchA的优先级设置为4096配置S3550A和S3550B间的F0/2连接为主链路:S3550A (config)# interface fastEthernet 0/2S3550A (config-if)# spanning-tree port-priority 0 !设置F0/2的端口优先级为0S2126A (config-if)# speed 10SwitchA(config)# endSwitchA# show spanning-tree !显示交换机的生成树模式及相关状态SwitchA# show spanning-tree interface fastEthernet 0/1 ! 显示Fa0/1接口STP状态快速生成树S3550A (config)# spanning-tree mode rstp ! 设置生成树为RSTP(802.1W)S3550A (config)# spanning-tree priority 0 配置S3550A为根交换机即设置SwitchA的优先级为0ACL配置Switch(config)#access-list 1 permit 172.16.0.0 0.0.255.255 靠近目的Switch(config)#interface ethernet 0Switch(config-if)#ip access-group 1 outSwitch(config)#access-list 101 deny tcp 192.168.1.0 0.0.0.255 host 192.168.10.100 eq 80Switch(config)#access-list 101 permit ip any anySwitch(config)#interface ethernet 1Switch(config-if)#ip access-group 101 outSwitch # show access-list 显示所有的ACLSwitch # show ip access-lists 1 显示IP ACL1Switch # show ip interface fastEthernet 1/1 显示f1/1接口的访问列表静态路由格式:router(config)# ip route [未直连的目的网段] [子网掩码] [转发路由器的IP地址/本地接口R1(config)# ip route 172.16.2.0 255.255.255.0 172.16.21.2 !配置静态路由R1# show ip route !查看路由表缺省路由:ip route 0.0.0.0 0.0.0.0 [转发路由器的IP地址/本地接口RIP协议R1(config)# router rip !启用RIP进程R1(config-router)# network 172.16.1.0 !公布直连网络R1(config-router)# network 172.16.21.0 !公布直连网络router# show ip protocols !验证RIP的配置R1# show ip interface brief !显示接口的摘要信息router# debug ip rip !在控制台显示RIP的工作状态PPP协议R1(config)# interface serial 1/2R1(config-if)# ip address 172.16.10.1 255.255.255.0R1(config-if)# encapsulation ppp !配置接口封装为PPP;两端均需配置R1(config-if)# no shutdownR1(config-if)# clock rate 64000NAT让内部主机在公网地址缺乏的情况下可以访问外部网络(主要命令)R1(config)# ip route 0.0.0.0 0.0.0.0 serial 1/2 先做缺省路由R1(config-if)#ip nat inside 进入F0/1,定义为内网接口R1(config-if)#ip nat outside 进入S1/2,定义为外网接口R1(config)#ip nat pool internet 200.1.8.7 200.2.8.7 netmask 255.255.255.0 定义内部全局地址池R1(config)#access-list 10 permit 172.16.1.0 0.0.0.255 定义允许转换的地址R1(config)#ip nat inside source list 10 pool internet overload 为内部本地调用转换地址池NAT发布主机R1(config)# ip route 0.0.0.0 0.0.0.0 serial 1/2 先做缺省路由R1(config)#int fa0/1R1(config-if)#ip nat insideR1(config-if)#exitR1(config)#int s1/2R1(config-if)#ip nat outsideR1(config-if)#exitR1(config)#ip nat pool webserver 172.16.8.5 172.16.8.5 netmask 255.255.255.0 定义内网服务器地址池R1(config)#access-list 3 permit host 200.1.8.7 定义外网的公网IPR1(config)#ip nat inside destination list 3 pool webserver 将外网的公网IP地址转换为web服务器地址R1(config)#ip nat inside source static tcp 172.16.8.5 80 200.1.8.7 80 定义访问外网IP的80端口时转换为内网的服务器IP 的80端口。

锐捷交换机命令大全

锐捷交换机命令大全

【第一部分】交换机支持的命令:1.交换机基本状态:s w i t c h:;R O M状态,路由器是r o m m o n> h o s t n a m e>;用户模式h o s t n a m e#;特权模式h o s t n a m e(c o n f i g)#;全局配置模式h o s t n a m e(c o n f i g-i f)#;接口状态2.交换机口令设置:s w i t c h>e n a b l e;进入特权模式s w i t c h#c o n f i g t e r m i n a l;进入全局配置模式s w i t c h(c o n f i g)#h o s t n a m e;设置交换机的主机名s w i t c h(c o n f i g)#e n a b l e s e c r e t x x x;设置特权加密口令s w i t c h(c o n f i g)#e n a b l e p a s s w o r d x x a;设置特权非密口令s w i t c h(c o n f i g)#l i n e c o n s o l e0;进入控制台口s w i t c h(c o n f i g-l i n e)#l i n e v t y04;进入虚拟终端s w i t c h(c o n f i g-l i n e)#l o g i n;允许登录s w i t c h(c o n f i g-l i n e)#p a s s w o r d x x;设置登录口令x x s w i t c h#e x i t;返回命令3.交换机V L A N设置:s w i t c h#v l a n d a t a b a s e;进入V L A N设置s w i t c h(v l a n)#v l a n2;建V L A N 2 s w i t c h(v l a n)#n o v l a n2;删v l a n 2 s w i t c h(c o n f i g)#i n t f0/1;进入端口 1 s w i t c h(c o n f i g-i f)#s w i t c h p o r t a c c e s s v l a n2;当前端口加入v l a n2 s w i t c h(c o n f i g-i f)#s w i t c h p o r t m o d e t r u n k;设置为干线s w i t c h(c o n f i g-i f)#s w i t c h p o r t t r u n k a l l o w e d v l a n1,2;设置允许的v l a n s w i t c h(c o n f i g-i f)#s w i t c h p o r t t r u n k e n c a p d o t1q;设置v l a n中继s w i t c h(c o n f i g)#v t p d o m a i n;设置发v t p域名s w i t c h(c o n f i g)#v t p p a s s w o r d;设置发v t p密码s w i t c h(c o n f i g)#v t p m o d e s e r v e r;设置发v t p模式s w i t c h(c o n f i g)#v t p m o d e c l i e n t;设置发v t p模式4.交换机设置I P地址:s w i t c h(c o n f i g)#i n t e r f a c e v l a n1;进入v l a n 1 s w i t c h(c o n f i g-i f)#i p a d d r e s s;设置I P地址s w i t c h(c o n f i g)#i p d e f a u l t-g a t e w a y;设置默认网关s w i t c h#d i r f l a s h:;查看闪存5.交换机显示命令:s w i t c h#w r i t e;保存配置信息s w i t c h#s h o w v t p;查看v t p配置信息s w i t c h#s h o w r u n;查看当前配置信息s w i t c h#s h o w v l a n;查看v l a n配置信息s w i t c h#s h o w i n t e r f a c e;查看端口信息s w i t c h#s h o w i n t f0/0;查看指定端口信息【第二部分】路由器支持的命令:1.路由器显示命令:router#showrun;显示配置信息router#showinterface;显示接口信息router#showiproute;显示路由信息router#showcdpnei;显示邻居信息router#reload;重新起动2.路由器口令设置:router>enable;进入特权模式router#configterminal;进入全局配置模式router(config)#hostname;设置交换机的主机名router(config)#enablesecretxxx;设置特权加密口令router(config)#enablepasswordxxb;设置特权非密口令router(config)#lineconsole0;进入控制台口router(config-line)#linevty04;进入虚拟终端router(config-line)#login;要求口令验证router(config-line)#passwordxx;设置登录口令xxrouter(config)#(Ctrl+z);返回特权模式router#exit;返回命令3.路由器配置:router(config)#ints0/0;进入Serail接口router(config-if)#noshutdown;激活当前接口router(config-if)#clockrate64000;设置同步时钟router(config-if)#ipaddress;设置IP地址router(config-if)#ipaddresssecond;设置第二个IProuter(config-if)#intf0/0.1;进入子接口router(config-subif.1)#ipaddress;设置子接口IProuter(config-subif.1)#encapsulationdot1q;绑定vlan中继协议router(config)#config-register0x2142;跳过配置文件router(config)#config-register0x2102;正常使用配置文件router#reload;重新引导4.路由器文件操作:router#copyrunning-configstartup-config;保存配置router#copyrunning-configtftp;保存配置到tftprouter#copystartup-configtftp;开机配置存到tftprouter#copytftpflash:;下传文件到flashrouter#copytftpstartup-config;下载配置文件ROM状态:Ctrl+Break;进入ROM监控状态rommon>confreg0x2142;跳过配置文件rommon>confreg0x2102;恢复配置文件rommon>reset;重新引导rommon>copyxmodem:flash:;从console传输文件;设置路由器IP;设置路由器掩码rommon>T;指定TFTP服务器IPrommon>TFTP_FILE=c2600.bin;指定下载的文件rommon>tftpdnld;从tftp下载rommon>dirflash:;查看闪存内容rommon>boot;引导IOS5.静态路由:iproute;命令格式;静态路由举例;默认路由举例6.动态路由:router(config)#iprouting;启动路由转发router(config)#routerrip;启动RIP路由协议。

锐捷交换机命令

锐捷交换机命令

锐捷交换机命令锐捷交换机配置命令交换机基本操作1.进入特权模式Switch>enableSwitch#2.返回用户模式Switch#exitPress RETURN to get started!Switch>配置模式:全局配置模式[主机名(config)#]:配置交换机的整体参数子模式:1.线路配置模式[主机名(config-line)#]:配置交换机的线路参数2.接口配置模式[主机名(config-if)#]:配置交换机的接口参数1.进入全局配置模式下Switch#configure terminalSwitch(config)#exitSwitch#2.进入线路配置模式Switch(config)#line console 0Switch(config-line)#exitSwitch(config)#3.进入接口配置模式Switch(config)#interface fastEthernet 0/1Switch(config-if)#exitSwitch(config)#从子模式下直接返回特权模式Switch(config-if)#endSwitch#交换机操作帮助特点:1.支持命令简写(按TAB键将命令补充完整)2.在每种操作模式下直接输入“?”显示该模式下所有的命令3.命令空格“?”显示命令参数并对其解释说明4.字符“?”显示以该字符开头的命令5.命令历史缓存: (Ctrl+P)显示上一条命令,(Ctrl+N)显示下一条命令6.错误提示信息交换机显示命令:显示交换机硬件及软件的信息Switch#show version显示当前运行的配置参数Switch#show running-config显示保存的配置参数Switch#show configure常用交换机EXEC命令将当前运行的配置参数复制到flash:Switch#write memory Building configuration...[OK]Switch#清空flash中的配置参数:Switch#delete flash:config.text Switch#交换机重新启动:Switch#reloadSystem configuration has been modified. Save? [yes/no]:n Proceed with reload? [confirm]配置交换机主机名:Switch(config)#hostname S2126GS2126G(config)#配置交换机口令:1、配置交换机的登陆密码S2126G(config)#enable secret level 1 0 star“0”表示输入的是明文形式的口令2、配置交换机的特权密码S2126G(config)#enable secret level 15 0 Star“0”表示输入的是明文形式的口令常用交换机配置命令:1、为交换机分配管理IP地址S2126G(config)#interface vlan 1S2126G(config-if)#ip address {IP address} {IP subnetmask}[secondary]2、将接口启用S2126G(config-if)#no shutdown3、将接口关闭S2126G(config-if)#shutdown4、配置接口速率S2126G(config-if)#speed [10|100|auto]5、配置接口双工模式S2126G(config-if)#duplex [auto|full|half显示接口状态:S2126G#show interfaces测定目的端的可达性:S2126G>ping {IP address}从TFTP服务器下载配置参数:S2126G#copy tftp startup-config 管理交换机MAC地址表:1、查看MAC地址表S2126G#show mac-address-table2、配置MAC地址表记录的生存时间(缺省为300秒)S2126G(config)#mac-address-table aging-time <10-1000000> 3、查看MAC地址表记录的生存时间S2126G#show mac-address-table aging-timeVLAN的配置:1.添加一个VLANS2126G(config)#vlan <1-4094>S2126G(config-vlan)#2.为VLAN命名(可选)S2126G(config-vlan)#name将交换机端口分配到VLAN1.配置Port VLANSwitch(config-if)#switchport access vlan <1-4094>2.配置Tag VLANSwitch(config-if)#switchport mode trunk1).配置本地(native)VLANSwitch(config-if)#switchport trunk native vlan <1-4094>2).从主干链路中清除VLANSwitch(config-if)#switchport trunk allowed vlan except注:VLAN1不可被清除VLAN的验证:1.显示全部的VLAN:Switch#show vlan2.显示单独的VLAN :Switch#show vlan id <1-4094>将VLAN信息保存到flash中:Switch#write memory从flash中清除VLAN信息:Switch#delete flash:vlan.datRSTP的配置:1.启用生成树:S2126G(config)#spanning-tree2.配置交换机优先级:S2126G(config)#spanning-tree priority<0-61440>“0”或“4096”的倍数(RSTP BPDU该值后12bit全0)3.配置交换机端口优先级:S2126G(config-if)#spanning-treeport-priority <0-240>“0”或“16”的倍数(RSTP BPDU该值后4bit全0)4、生成树hello时间的配置(由Root决定):S2126G(config)#spanning-tree hello-time <1-10>5、生成树的验证:Switch#show spanning-treeSwitch#show spanning-tree interface <接口名称> <接口编号>以上用于锐捷交换机的。

  1. 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
  2. 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
  3. 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。

锐捷交换机命令交换机基本操作1.进入特权模式Switch>enableSwitch#2.返回用户模式Switch#exitPress RETURN to get started!Switch>配置模式:全局配置模式[主机名(config)#]:配置交换机的整体参数子模式:1.线路配置模式[主机名(config-line)#]:配置交换机的线路参数2.接口配置模式[主机名(config-if)#]:配置交换机的接口参数1.进入全局配置模式下Switch#configure terminalSwitch(config)#exitSwitch#2.进入线路配置模式Switch(config)#line console 0Switch(config-line)#exitSwitch(config)#3.进入接口配置模式real, in each pen business lending Qian not for by pen query, led to mortgage failure of. (Vi) not in accordance with the relevant provisions of the Bank operation, failed to identify false documents, certificates, authorizations, warrants, etc. (VII) in the credit risk management system to provide false information, is not required by the guest rating credit management objective, impartial ratings of credit, resulting in credit decision-making errors. (H) the investigation report conclusions of false record, misleading statement or material omission, resulting in credit decision-making errors. (I) the orders, directives, orders, suggest that others not involved in the investigation business, issued by the investigators. (10) without the approval of authorities, after the first credit investigation, credit first and then record, counter-current process operations such as operation prior to approval. (11) article does not meet the risk management Department, Marketing Management Department to carry out supervision and inspection and due diligence evaluations or providing false information. (12) other violations result in credit business at substantial risk or significant potential risk behaviours. Sixth chapter supplementary articles article 28th of this approach by the Head Office of risk management Departmentis responsible for the interpretation and amendment. 29th spontaneous herein from the date of implementation. Qilu silver computer transmission of qilu Bank documents (2012), No. 289Qilu Bank personal credit on issuing the Notification Guide to business risk management branch, jurisdiction and the jurisdiction of business lines, Jinanbranch, head office departments within its jurisdiction: in order to improve the quality of individual credit business, optimize the structure of assets, promotion ofSwitch(config)#interface fastEthernet 0/1Switch(config-if)#exitSwitch(config)#从子模式下直接返回特权模式Switch(config-if)#endSwitch#交换机操作帮助特点:1.支持命令简写(按TAB键将命令补充完整)2.在每种操作模式下直接输入“?”显示该模式下所有的命令3.命令空格“?”显示命令参数并对其解释说明4.字符“?”显示以该字符开头的命令5.命令历史缓存: (Ctrl+P)显示上一条命令,(Ctrl+N)显示下一条命令6.错误提示信息交换机显示命令:显示交换机硬件及软件的信息 Switch#show version显示当前运行的配置参数 Switch#show running-config显示保存的配置参数 Switch#show configure常用交换机EXEC命令将当前运行的配置参数复制到flash:Switch#write memoryBuilding configuration...[OK]Switch#real, in each pen business lending Qian not for by pen query, led to mortgage failure of. (Vi) not in accordance with the relevant provisions of the Bank operation, failed to identify false documents, certificates, authorizations, warrants, etc. (VII) in the credit risk management system to provide false information, is not required by the guest rating credit management objective, impartial ratings of credit, resulting in credit decision-making errors. (H) the investigation report conclusions of false record, misleading statement or material omission, resulting in credit decision-making errors. (I) the orders, directives, orders, suggest that others not involved in the investigation business, issued by the investigators. (10) without the approval of authorities, after the first credit investigation, credit first and then record, counter-current process operations such as operation prior to approval. (11) article does not meet the risk management Department, Marketing Management Department to carry out supervision and inspection and due diligence evaluations or providing false information. (12) other violations result in credit business at substantial risk or significant potential risk behaviours. Sixth chapter supplementary articles article 28th of this approach by the Head Office of risk management Departmentis responsible for the interpretation and amendment. 29th spontaneous herein from the date of implementation. Qilu silver computer transmission of qilu Bank documents (2012), No. 289Qilu Bank personal credit on issuing the Notification Guide to business risk managementbranch, jurisdiction and the jurisdiction of business lines, Jinan branch, head office departments within its jurisdiction: in order to improve the quality of individual credit business, optimize thestructure of assets, promotion of清空flash中的配置参数:Switch#delete flash:config.textSwitch#交换机重新启动:Switch#reloadSystem configuration has been modified. Save? [yes/no]:nProceed with reload? [confirm]配置交换机主机名:Switch(config)#hostname S2126GS2126G(config)#配置交换机口令:1、配置交换机的登陆密码S2126G(config)#enable secret level 1 0 star“0”表示输入的是明文形式的口令2、配置交换机的特权密码S2126G(config)#enable secret level 15 0 Star“0”表示输入的是明文形式的口令常用交换机配置命令:1、为交换机分配管理IP地址S2126G(config)#interface vlan 1S2126G(config-if)#ip address {IP address} {IP subnetmask}[secondary]2、将接口启用S2126G(config-if)#no shutdown3、将接口关闭S2126G(config-if)#shutdownreal, in each pen business lending Qian not for by pen query, led to mortgage failure of. (Vi) not in accordance with the relevant provisions of the Bank operation, failed to identify false documents, certificates, authorizations, warrants, etc. (VII) in the credit risk management system to provide false information, is not required by the guest rating credit management objective, impartial ratings of credit, resulting in credit decision-making errors. (H) the investigation report conclusions of false record, misleading statement or material omission, resulting in credit decision-making errors. (I) the orders, directives, orders, suggest that others not involved in the investigation business, issued by the investigators. (10) without the approval of authorities, after the first credit investigation, credit first and then record, counter-current process operations such as operation prior to approval. (11) article does not meet the risk management Department, Marketing Management Department to carry out supervision and inspection and due diligence evaluations or providing false information. (12) other violations result in credit business at substantial risk or significant potential risk behaviours. Sixth chapter supplementary articles article 28th of this approach by the Head Office of risk management Departmentis responsible for the interpretation and amendment. 29th spontaneous herein from the date of implementation. Qilu silver computer transmission of qilu Bank documents (2012), No. 289Qilu Bank personalcredit on issuing the Notification Guide to business risk management branch, jurisdiction and the jurisdiction of business lines, Jinan branch, head office departments within its jurisdiction: in order to improve the quality of individual credit business, optimize the structure of assets, promotion of4、配置接口速率S2126G(config-if)#speed [10|100|auto]5、配置接口双工模式S2126G(config-if)#duplex [auto|full|half显示接口状态:S2126G#show interfaces测定目的端的可达性:S2126G>ping {IP address}从TFTP服务器下载配置参数:S2126G#copy tftp startup-config管理交换机MAC地址表:1、查看MAC地址表S2126G#show mac-address-table缺省为300秒) 2、配置MAC地址表记录的生存时间(S2126G(config)#mac-address-table aging-time <10-1000000>3、查看MAC地址表记录的生存时间S2126G#show mac-address-table aging-timeVLAN的配置:1.添加一个VLANS2126G(config)#vlan <1-4094>S2126G(config-vlan)#2.为VLAN命名(可选)S2126G(config-vlan)#name将交换机端口分配到VLAN1.配置Port VLANSwitch(config-if)#switchport access vlan <1-4094> real, in each pen business lending Qian not for by pen query, led to mortgage failure of. (Vi) not in accordance with the relevant provisions of the Bank operation, failed to identify false documents, certificates, authorizations, warrants, etc. (VII) in the credit risk management system to provide false information, is not required by the guest rating credit management objective, impartial ratings of credit, resulting in credit decision-making errors. (H) the investigation report conclusions of false record, misleading statement or material omission, resulting in credit decision-making errors. (I) the orders, directives, orders, suggest that others not involved in the investigation business, issued by the investigators. (10) without the approval of authorities, after the first credit investigation, credit first and then record, counter-current process operations such as operation prior to approval. (11) article does not meet the risk management Department, Marketing Management Department to carry out supervision and inspection and due diligence evaluations or providing false information. (12) other violations result in credit business at substantial risk or significant potential risk behaviours. Sixth chapter supplementary articles article 28th of this approach by the Head Office of risk management Department is responsible for the interpretation and amendment. 29th spontaneousherein from the date of implementation. Qilu silver computer transmission of qilu Bank documents (2012), No. 289Qilu Bank personal credit on issuing the Notification Guide to business risk management branch, jurisdiction and the jurisdiction of business lines, Jinan branch, head office departments within its jurisdiction: in order to improve the quality of individual credit business, optimize the structure of assets, promotion of2.配置Tag VLANSwitch(config-if)#switchport mode trunk1).配置本地(native)VLANSwitch(config-if)#switchport trunk native vlan <1-4094>2).从主干链路中清除VLANSwitch(config-if)#switchport trunk allowed vlan except 注:VLAN1不可被清除VLAN的验证:1.显示全部的VLAN:Switch#show vlan2.显示单独的VLAN :Switch#show vlan id <1-4094>将VLAN信息保存到flash中:Switch#write memory从flash中清除VLAN信息:Switch#delete flash:vlan.datRSTP的配置:1.启用生成树:S2126G(config)#spanning-tree2.配置交换机优先级:S2126G(config)#spanning-tree priority <0-61440>“0”或“4096”的倍数(RSTP BPDU该值后12bit全0)3.配置交换机端口优先级:S2126G(config-if)#spanning-tree port-priority <0-240>“0”或“16”的倍数(RSTP BPDU该值后4bit全0)4、生成树hello时间的配置(由Root决定):S2126G(config)#spanning-tree hello-time <1-10>5、生成树的验证:Switch#show spanning-treeSwitch#show spanning-tree interface <接口名称> <接口编号>以上用于锐捷交换机的。

相关文档
最新文档