MOXA交换机环网配置图解说明EDS A MM SC
MOXA交换机使用说明教学内容
MOXA交换机使用说明教学内容一、简介MOXA交换机是一种高性能的工业以太网交换机，它能够满足工业环境中对网络可靠性和稳定性的要求。
MOXA交换机具有多个端口，支持各种网络协议，并具有多种网络管理和优化功能。
本教程将介绍如何正确使用MOXA交换机，并详细说明其各项功能。
二、安装与配置1.检查交换机是否损坏：确认交换机外观是否完好，是否有明显的损坏或缺陷。
2.连接电源：将交换机的电源插头插入电源插座，然后按下开关，确认交换机的指示灯是否亮起。
3.连接设备：使用网线将设备与交换机的端口相连。
4.配置网络参数：使用电脑连接至交换机的管理端口，通过浏览器登录交换机的配置界面，根据需要配置网络参数，如IP地址、子网掩码等。
5.网络测试：在配置完成后，使用网络测试工具对交换机进行测试，确认网络连接正常。
三、交换机配置1.VLAN配置：VLAN是一种将交换机端口划分为不同虚拟局域网的技术。
在交换机中配置VLAN，可以实现不同设备之间的隔离和通信。
2. QoS配置：QoS（Quality of Service）是一种网络优化技术，通过分配带宽和优先级，可以保证关键应用的网络传输质量。
3.静态路由配置：在交换机中配置静态路由，可以实现不同子网之间的通信。
4.端口管理：配置端口速率、全双工或半双工模式、流控等参数，以充分利用网络带宽和提高网络性能。
5.网络监控与诊断：通过交换机的网络监控功能，可以实时监测网络流量、连接状态和端口的状态，以及进行故障诊断和排除。
四、安全性配置1.密码设置：修改交换机的默认登录密码，以保护设备免受未经授权的访问。
2. 限制访问：通过配置ACL（Access Control List）或MAC过滤，限制特定IP地址或MAC地址的访问。
3.HTTPS加密：将交换机的管理界面配置为使用HTTPS加密协议，提高数据传输的安全性。
4.日志记录：开启日志记录功能，记录交换机的操作和事件，以便后续分析和审计。
摩克斯工业级以太网交换机 EDS-205A 208A 系列产品说明书
Moxa EtherDevice SwitchEDS-205A/208A SeriesHardware Installation GuideFourth Edition, October 2009© 2009 Moxa Inc. All rights reserved.Reproduction without permission is prohibited.P/N: 1802002050023OverviewThe EDS-205A/208A series of industrial Ethernet switches are entry-level industrial 5 and 8-port Ethernet switches that support IEEE 802.3, IEEE 802.3u, and IEEE 802.3x with 10/100M, full/half-duplex, and MDI/MDIXauto-sensing.The EDS-205A/208A series provides 12/24/48 VDC (9.6 to 60VDC)/18 to 30 VAC redundant power inputs that can be connected simultaneously to a live AC/DC power source. The switches are available with a standard operating temperature range from -10 to 60°C, or with a wide operating temperature range from -40 to 75°C, and IP30 metal housing makes them rugged enoughfor any harsh industrial environment.To provide greater versatility for use with applications from different industries, the EDS-205A/208A also allow users to enable or disable broadcast storm protection with DIP switches on the outer panel.The EDS-205A/208A switches can be easily installed with DIN-Rail mounting as well as distribution boxes. The DIN-rail mounting capability and IP30 metal housing with LED indicators make the plug-and-play EDS-205A/208A switches reliable and easy to use.NOTE Throughout this Hardware Installation Guide, we use EDS as an abbreviation for Moxa EtherDevice Switch:EDS = Moxa EtherDevice SwitchPackage ChecklistYour EDS is shipped with the following items. If any of these items is missing or damaged, please contact your customer service representative for assistance. y Moxa EtherDevice™ Switchy Hardware Installation Guidey Moxa Product Warranty bookletFeaturesHigh Performance Network Switching Technologyy EDS-205A: 10/100BaseT(X) (RJ45), 100 BaseFX (SC/ST connector, multi/single-mode)y EDS-208A series: 10/100BaseT(X) (RJ45), 100 BaseFX (SC/ST connector, multi/single-mode)y10/100M, Full/Half-Duplex, MDI/MDIX auto-sensingy IEEE 802.3/802.3u/802.3xy Store and Forward switching process type, 1024 address entriesRugged Designy Redundant dual 12/24/48 VDC (9.6 to 60VDC) or 18 to 30 VAC at 47 to63 Hz power inputy Operating temperature range from -10 to 60°C,or extended operating temperature of -40 to 75°C for (-T) models.y IP30 metal housingy DIN-rail or panel mounting abilityPanel Layout of EDS-205A/208A (Standard)Top Panel ViewTop Panel ViewRear Panel View Rear Panel View2EDS-208A Front Panel View8EDS-205A Front Panel View7321412431. Grounding screw2.Terminal block for power input P1/P2 3. Heat dissipationorifices 4. DIP Switches 5. Power input P1 LED 6.Power input P2 LED 7. 10/100BaseT(X) Port8.TP port’s 10/100 Mbps LED 9. Model Name10. Screw hole for wallmounting kit 11. DIN-Rail KitTop Panel ViewRear Panel ViewFront Panel View23214Top Panel ViewRear Panel View Front Panel View321456256The appearance of EDS-205A-S-SC is identical to EDS-205A-M-SC.1. Grounding screw2.Terminal block for power input P1/P23. Heat dissipationorifices 4. DIP Switches 5.Power input P1 LED 6. Power input P2 LED 7. 10/100BaseT(X) Port8.TP port’s 10/100 Mbps LED 9. Model Name 10. 100BaseFX Port 11. FX port’s 100 MbpsLED12. Screw hole for wallmounting kit 13. DIN-Rail KitTop Panel ViewRear Panel ViewFront Panel ViewTop Panel View Rear Panel View Front Panel View11The appearance of EDS-208A-S-SC is identical to EDS-208A-M-SC.1. Grounding screw2.Terminal block for power input P1/P2 3. Heat dissipationorifices 4. DIP Switches5. Power input P1 LED6. Power input P2 LED7. 10/100BaseT(X) Port8.TP port’s 10/100 Mbps LED9. Model Name 10. 100BaseFX Port 11. FX port’s 100 MbpsLED12. Screw hole for wallmounting kit13. DIN-Rail KitPanel Layout of EDS-208A-MM-SC/STTop Panel ViewRear Panel ViewEDS-208A-MM-SC Front Panel ViewTop Panel View Rear Panel View EDS-208A-MM-STFront Panel View11NOTE:The appearance of EDS-208A-SS-SC is identical to EDS-208A-MM-SC.1. Grounding screw2.Terminal block for power input P1/P23. Heat dissipationorifices 4. DIP Switches5. Power input P1 LED6. Power input P2 LED7. 10/100BaseT(X) Port8.TP port’s 10/100 Mbps LED9. Model Name 10. 100BaseFX Port 11. FX port’s 100 MbpsLED12. Screw hole for wallmounting kit13. DIN-Rail KitMounting Dimensions (unit = mm)DIN-Rail MountingThe aluminum DIN-rail attachment plate should already be fixed to the back panel of the EDS when you take it out of the box. If you need to reattach the DIN-rail attachment plate, make sure the stiff metal spring is situated towards the top, as shown in the figures below.STEP 1:Insert the top of the DIN-Rail into the slot just below the stiff metal spring. STEP 2:The DIN-Rail attachment unit will snap into place as shown below.To remove the EDS from the DIN-Rail, simply reverse Steps 1 and 2 above.Wall Mounting (optional)For some applications, you will find it convenient to mount theSTEP 1: Remove thealuminum DIN-Railattachment plate from theEDS-205A/208A’s rearpanel, and then attach thewall mount plates as shownin the diagram at the right.⇒STEP 2:Mounting the EDS-205A/208A on the wall requires 4screws. Use the switch, with wall mount plates attached,as a guide to mark the correct locations of the 4 screws.The heads of the screws should be less than 6.0 mm indiameter, and the shafts should be less than 3.5 mm indiameter, as shown in the figure at the right.NOTE Before tightening the screws into the wall, make sure the screw head and shank size are suitable by inserting the screw into one ofthe keyhole-shaped apertures of the wall mounting plates.Do not screw the screws in completely—leave about 2 mm to allow room for sliding the wall mount panel between the wall and the screws.STEP 3:Once the screws are fixed on the wall, insert the four screw heads through the large parts of the keyhole-shaped apertures, and then slide theEDS-205A/208A downwards, as indicated. Tighten the four screws for added stability.⇒Wiring RequirementsYou should also pay attention to the following points:y Use separate paths to route wiring for power and devices. If power wiring and device wiring paths must cross, make sure the wires are perpendicular at the intersection point.NOTE: Do not run signal or communications wiring and power wiring in the same wire conduit. To avoid interference, wires with different signal characteristics should be routed separately.y You can use the type of signal transmitted through a wire to determine which wires should be kept separate. The rule of thumb is that wiring that shares similar electrical characteristics can be bundled together.y Keep input wiring and output wiring separated.y It is strongly advised that you label wiring to all devices in the system when necessary.Grounding the EtherDevice SwitchGrounding and wire routing help limit the effects of noise due toelectromagnetic interference (EMI). Run the ground connection from the ground screw to the grounding surface prior to connecting devices.Wiring the Redundant Power InputsThe top two contacts and the bottom two contacts of the 4-contact terminal block connector on the EDS’s top panel are used for the EDS’s two AC/DC inputs. Top and front views of one of the terminal block connectors are shown here.STEP 1: Insert the negative/positive AC/DC wires into the V-/V+ terminals.STEP 2: To keep the AC/DC wires from pulling loose, use a small flat-blade screwdriver to tighten the wire-clamp screws on the front of the terminal block connector.STEP 3: Insert the plastic terminal blockconnector prongs into the terminal block receptor, which is located on EDS’s top panel.Communication ConnectionsThe EDS-205A models have 4 or 5 10/100BaseT(X) Ethernet ports, and 1 or 0 (zero) 100 BaseFX multi/single-mode (SC/ST-type connector) fiber ports. The EDS-208A models have 6, 7 or 8 10/100BaseT(X) Ethernet ports, and 2, 1 or 0 (zero) 100 BaseFX multi/single-mode (SC/ST-type connector) fiber ports.10/100BaseT(X) Ethernet Port ConnectionThe 10/100BaseT(X) ports located on the EDS’s front panel are used to connect to Ethernet-enabled devices. Below we show pinouts for both MDI (NIC-type) ports and MDI-X (HUB/Switch-type) ports, and also show cable wiring diagrams for straight-through and cross-over Ethernet cables.MDI Port PinoutsMDI-X Port Pinouts 8-pin RJ45Pin Signal 1 Tx+ 2 Tx- 3 Rx+ 6 Rx-Pin Signal1 Rx+2 Rx-3 Tx+ 6 Tx-RJ45 (8-pin) to RJ45 (8-pin) Straight-Through Cable Wiring Switch Port RJ45ConnectorRJ45Connector Tx+Tx-Rx+Rx-NIC Port Cable Wiring 3 36 61 122Rx+Rx-Tx+Tx-RJ45 (8-pin) to RJ45 (8-pin) Cross-Over Cable Wiring Switch Port (NIC Port)RJ45Connector RJ45Connector Tx+Tx-Rx+Rx-(Rx+)(Rx-)(Tx+)(Tx-)(Tx+)(Tx-)(Rx+)(Rx-)Switch Port (NIC Port)Cable Wiring 3 1621 326Rx+Rx-Tx+Tx-100BaseFX Ethernet Port ConnectionThe concept behind the SC/ST port and cable is quite straightforward. Suppose you are connecting devices I and II; contrary to electrical signals, optical signals do not require a circuit in order to transmit data. Consequently, one of the optical lines is used to transmit data from device I to device II, and the other optical line is used transmit data from device II to device I, for full-duplex transmission.Remember to connect the Tx (transmit) port of device I to the Rx (receive) port of device II, and the Rx (receive) port of device I to the Tx (transmit) port of device II. If you make your own cable, we suggest labeling the two sides of the same line with the same letter (A-to-A and B-to-B, as shown below, or A1-to-A2 and B1-to-B2).SC-Port to SC-Port Cable WiringTxRxAABBCable WiringA A BBST-Port to ST-Port Cable WiringCable WiringA ABBRedundant Power InputsBoth power inputs can be connected simultaneously to live AC/DC power sources. If one power source fails, the other live source acts as a backup, and automatically supplies all of the EDS’s power needs.DIP Switch SettingsEDS-205A/208A DIP SwitchesThe default setting for each DIP Switch is OFF.The following table explains the effect of settingthe DIP Switches to the ON positions.DIP Switch Setting Description------ Serves no function (reserved for future use).ON Enables broadcast storm protectionBSPOFF Disables broadcast storm protectionLED IndicatorsThe front panel of the Moxa EtherDevice Switch contains several LED indicators. The function of each LED is described in the table below.LED Color State DescriptionOn Power is being supplied to power input P1.P1 AMBEROff Power is not being supplied to power inputP1.On Power is being supplied to power input P2.P2 AMBEROff Power is not being supplied to power inputP2.On TP port’s 10 Mbps link is active.10M YellowBlinking Data is being transmitted at 10 Mbps.Off TP Port’s 10 Mbps link is inactiveOn TP port’s 100 Mbps link is active.Blinking Data is being transmitted at 100 Mbps.100M GREENOff 100Base TP Port’s link is inactive. Auto MDI/MDI-X ConnectionThe Auto MDI/MDI-X function allows users to connect the EDS’s10/100BaseTX ports to any kind of Ethernet device, without needing to pay attention to the type of Ethernet cable being used for the connection. This means that you can use either a straight-through cable or cross-over cable to connect the EDS to Ethernet devices.Dual Speed Functionality and SwitchingThe Moxa EtherDevice Switch’s 10/100 Mbps switched RJ45 port auto negotiates with the connected device for the fastest data transmission rate supported by both devices. All models of Moxa EtherDevice Switch areplug-and-play devices, so that software configuration is not required at installation, or during maintenance. The half/full duplex mode for the switched RJ45 ports is user dependent and changes (by auto-negotiation) to full or half duplex, depending on which transmission speed is supported by the attached device.Switching, Filtering, and ForwardingEach time a packet arrives at one of the switched ports, a decision is made to either filter or forward the packet. Packets with source and destination addresses belonging to the same port segment will be filtered, constraining those packets to one port, and relieving the rest of the network from the need to process them. A packet with destination address on another port segment will be forwarded to the appropriate port, and will not be sent to ports where it is not needed. Packets that are used in maintaining the operation of the network (such as the occasional multi-cast packet) are forwarded to all ports. The EDS operates in the store-and-forward switching mode, which eliminates bad packets and enables peak performance to be achieved when there is heavy traffic on the network.Switching and Address LearningThe EDS has an address table that can hold up to 1024 addresses, which makesit suitable for use with large networks. The address tables are self-learning, sothat as nodes are added or removed, or moved from one segment to another, the EDS automatically keeps up with new node locations. An address-agingalgorithm causes the least-used addresses to be deleted in favor of newer, more frequently used addresses. To reset the address buffer, power down the unit andthen power it back up.Auto-Negotiation and Speed SensingAll of the EDS’s RJ45 Ethernet ports independently support auto-negotiationfor speeds in the 10BaseT and 100BaseTX modes, with operation according tothe IEEE 802.3u standard. This means that some nodes could be operating at10 Mbps, while at the same time, other nodes are operating at 100 Mbps.Auto-negotiation takes place when an RJ45 cable connection is made, and theneach time a LINK is enabled. The EDS advertises its capability for using either10 Mbps or 100 Mbps transmission speeds, with the device at the other end ofthe cable expected to advertise in a similar manner. Depending on what type of device is connected, this will result in agreement to operate at a speed of either10 Mbps or 100 Mbps. If an EDS RJ45 Ethernet port is connected to anon-negotiating device, it will default to 10 Mbps speed and half-duplex mode,as required by the IEEE 802.3u standard.SpecificationsTechnologyStandards IEEE 802.3 for 10BaseT,IEEE 802.3u for 100BaseT(X) and 100BaseFX,IEEE 802.3x for Flow ControlProcessing Type Store and ForwardFlow Control IEEE 802.3x flow control, back pressure flowcontrolInterfaceRJ45 Ports 10/100BaseT(X) auto negotiation speed, F/Hduplex mode, and auto MDI/MDI-X connectionFiber Ports 100BaseFX ports (SC/ST connector,multi/single-mode)LED Indicators P1, P2 (Power), 10/100M (TP port), and 100M(Fiber port)DIP Switch enable/disable broadcast storm protectionOptical Fiber100BaseFXMulti-mode Single-mode Wavelength 1300 nm 1310 nmMax. TX -10 dBm 0 dBmMin. TX -20 dBm -5 dBmRX Sensitivity -32 dBm -34 dBmLink Budget 12 dB 29 dB5 km aTypical Distance40 km c4 km bSaturation -6 dBm -3 dBming [50/125μm, 800 MHz*km] cableing [62.5/125μm, 500 MHz*km] cableing [9/125 μm, 3.5 PS/(nm*km)] cablePowerInput Voltage 12/24/48 VDC (9.6 to 60 VDC),18 to 30VAC (47 to 63 Hz)Input Current @ 24VDC 0.1 A (EDS-205A)0.11 A (EDS-205A-M/S)0.13 A (EDS-208A)0.17 A (EDS-208A-M/S)0.22 A (EDS-208A-MM/SS)Connection Removable 4-contact terminal block1.1 AOverload CurrentProtectionReverse Polarity Protection PresentPhysical CharacteristicsHousing IP30 protection, metal caseDimensions EDS-208A Series: 50 x 115 x 70 mmEDS-205A: 30 x 115 x 70 mmWeight EDS-208A Series: 275 gEDS-205A: 175 gInstallation DIN-Rail Mounting, Wall Mounting(with optional kit)Environmental LimitsOperating Temperature -10 to 60°C (14 to 140°F)-40 to 75°C (-40 to 167°F) for -T models Storage Temperature -40 to 85°C (-40 to 185°F)Ambient Relative Humidity5 to 95% (non-condensing)Regulatory ApprovalsSafety UL508 (pending)Hazardous Location UL/cUL Class I, Division 2, Groups A, B, C, andD; ATEX Class I, Zone 2, Ex nC nL IIC T4(Pending)EMI FCC Part 15, CISPR (EN55022) class AEMS EN61000-4-2 (ESD), Level 3EN61000-4-3 (RS), Level 3EN61000-4-4 (EFT), Level 3EN61000-4-5 (Surge), Level 3EN61000-4-6 (CS), Level 3EN61000-4-8EN61000-4-1160068-2-27Shock IEC60068-2-32Freefall IEC60068-2-6Vibration IECWARRANTY 5 yearsTechnical Support Contact Information /supportMoxa Americas:Toll-free: 1-888-669-2872 Tel: +1-714-528-6777 Fax: +1-714-528-6778 Moxa Europe:Tel: +49-89-3 70 03 99-0 Fax: +49-89-3 70 03 99-99Moxa Asia-Pacific:Tel: +886-2-8919-1230 Fax: +886-2-8919-1231 Moxa China (Beijing office):Tel: +86-10-6872-3959/60/61 Fax: +86-10-6872-3958。
MOXA EDS-508A 8端口Managed Ethernet交换机说明书
EDS-508A Series8-port managed EthernetswitchesFeatures and Benefits•Turbo Ring and Turbo Chain (recovery time <20ms @250switches),andSTP/RSTP/MSTP for network redundancy•TACACS+,SNMPv3,IEEE 802.1X,HTTPS,and SSH to enhance networksecurity•Easy network management by web browser,CLI,Telnet/serial console,Windows utility,and ABC-01•Supports MXstudio for easy,visualized industrial network managementCertificationsIntroductionThe EDS-508A standalone 8-port managed Ethernet switches,with their advanced Turbo Ring and Turbo Chain technologies (recovery time <20ms),RSTP/STP,and MSTP,increase the reliability and availability of your industrial Ethernet network.Models with a wide operating temperature range of -40to 75°C are also available,and the switches support advanced management and security features,making the EDS-508A switches suitable for any harsh industrial environment.Additional Features and Benefits•Command line interface (CLI)for quickly configuring major managed functions•DHCP Option 82for IP address assignment with different policies •Supports EtherNet/IP and Modbus TCP protocols for device management and monitoring•Compatible with PROFINET protocol for transparent data transmission•Automatic warning by exception through email and relay output •IGMP snooping and GMRP for filtering multicast traffic•Port-based VLAN,IEEE 802.1Q VLAN,and GVRP to ease network planning•QoS (IEEE 802.1p/1Q and TOS/DiffServ)to increase determinism •Port Trunking for optimum bandwidth utilization•RMON for proactive and efficient network monitoring•SNMPv1/v2c/v3for different levels of network management•Bandwidth management to prevent unpredictable network status •Lock port function for blocking unauthorized access based on MAC addressSpecificationsInput/Output InterfaceAlarm Contact Channels 2,Relay output with current carrying capacity of 1A @24VDC Digital Input Channels 2Digital Inputs+13to +30V for state 1-30to +3V for state 0Max.input current:8mA ButtonsReset button100BaseFX Ports(multi-mode ST connector)EDS-508A-MM-ST Series:2100BaseFX Ports(single-mode SC connector)EDS-508A-SS-SC Series:2100BaseFX Ports,Single-Mode SC Connector,80kmEDS-508A-SS-SC-80Series:2Standards IEEE802.3for10BaseTIEEE802.3u for100BaseT(X)and100BaseFXIEEE802.1X for authenticationIEEE802.1D-2004for Spanning Tree ProtocolIEEE802.1w for Rapid Spanning Tree ProtocolIEEE802.1s for Multiple Spanning Tree ProtocolIEEE802.1Q for VLAN TaggingIEEE802.1p for Class of ServiceIEEE802.3x for flow controlIEEE802.3ad for Port Trunk with LACPOptical Fiber800Typical Distance4km5km40km80kmWave-lengthTypical(nm)130013101550TX Range(nm)1260to13601280to13401530to1570 RX Range(nm)1100to16001100to16001100to1600Optical PowerTX Range(dBm)-10to-200to-50to-5 RX Range(dBm)-3to-32-3to-34-3to-34 Link Budget(dB)122929 Dispersion Penalty(dB)311Note:When connecting a single-mode fiber transceiver,we recommend using anattenuator to prevent damage caused by excessive optical power.Note:Compute the“typical distance”of a specific fiber transceiver as follows:Linkbudget(dB)>dispersion penalty(dB)+total link loss(dB).Ethernet Software FeaturesFilter802.1Q VLAN,Port-based VLAN,IGMP v1/v2,GVRP,GMRPIndustrial Protocols EtherNet/IP,Modbus TCPManagement IPv4/IPv6,SNMPv1/v2c/v3,LLDP,Port Mirror,Back Pressure Flow Control,BOOTP,DDM,DHCP Option66/67/82,DHCP Server/Client,Fiber check,Flow control,RARP,RMON,SMTP,SNMP Inform,Syslog,Telnet,TFTPMIB MIB-II,Bridge MIB,Ethernet-like MIB,P-BRIDGE MIB,Q-BRIDGE MIB,RMON MIBGroups1,2,3,9,RSTP MIBRedundancy Protocols STP,MSTP,RSTP,LACP,Link Aggregation,Turbo Chain,Turbo Ring v1/v2 Security HTTPS/SSL,TACACS+,Port Lock,RADIUS,SSHTime Management NTP Server/Client,SNTP,IEEE1588v2PTP(software-based)Max.No.of VLANs64Packet Buffer Size1MbitsPriority Queues4VLAN ID Range VID1to4094LED InterfaceLED Indicators PWR1,PWR2,FAULT,10/100M(TP port),100M(fiber port),MSTR/HEAD,CPLR/TAIL Serial InterfaceConsole Port RS-232(TxD,RxD,GND),8-pin RJ45(115200,n,8,1)DIP Switch ConfigurationEthernet Interface Turbo Ring,Master,Coupler,ReservePower ParametersConnection2removable6-contact terminal block(s)Input Voltage12/24/48VDC,Redundant dual inputsOperating Voltage9.6to60VDCInput Current EDS-508A Series:0.22A@24VDCEDS-508A-MM/SS Series:0.30A@24VDCOverload Current Protection SupportedReverse Polarity Protection SupportedPhysical CharacteristicsHousing MetalIP Rating IP30Dimensions80.2x135x105mm(3.16x5.31x4.13in)Weight1040g(2.3lb)Installation DIN-rail mounting,Wall mounting(with optional kit)Environmental LimitsOperating Temperature Standard Models:-10to60°C(14to140°F)Wide Temp.Models:-40to75°C(-40to167°F)Storage Temperature(package included)-40to85°C(-40to185°F)Ambient Relative Humidity5to95%(non-condensing)Standards and CertificationsSafety EN60950-1,UL60950-1,CSA C22.2No.60950-1,UL508Hazardous Locations ATEX,Class I Division2EMC EN55032/24EMI CISPR32,FCC Part15B Class AEMS IEC61000-4-2ESD:Contact:6kV;Air:8kVIEC61000-4-3RS:80MHz to1GHz:20V/mIEC61000-4-4EFT:Power:2kV;Signal:1kVIEC61000-4-5Surge:Power:2kV;Signal:2kVIEC61000-4-6CS:10VIEC61000-4-8PFMFShock IEC60068-2-27Vibration IEC60068-2-6Freefall IEC60068-2-31MTBFTime1,043,909hrsStandards Telcordia(Bellcore),GBWarrantyWarranty Period5yearsDetails See /warrantyPackage ContentsDevice1x EDS-508A Series switchCable1x DB9female to RJ4510-pinInstallation Kit4x cap,plastic,for RJ45port2x cap,plastic,for SC fiber port(-SC models)2x cap,plastic,for ST fiber port(-ST models)Documentation1x quick installation guide1x warranty card1x product certificates of quality inspection,Simplified Chinese1x product notice,Simplified ChineseDimensionsOrdering Information80EDS-508A8––––-10to60°C EDS-508A-T8––––-40to75°C EDS-508A-MM-SC62–––-10to60°CEDS-508A-MM-SC-62–––-40to75°CTEDS-508A-MM-ST6–2––-10to60°C EDS-508A-MM-ST-T6–2––-40to75°C EDS-508A-SS-SC6––2–-10to60°C EDS-508A-SS-SC-T6––2–-40to75°CEDS-508A-SS-SC-6–––2-10to60°C80EDS-508A-SS-SC-6–––2-40to75°C80-TAccessories(sold separately)Storage KitsABC-01Configuration backup and restoration tool for managed Ethernet switches and AWK Series wirelessAPs/bridges/clients,0to60°C operating temperaturePower SuppliesDR-120-24120W/2.5A DIN-rail24VDC power supply with universal88to132VAC or176to264VAC input byswitch,or248to370VDC input,-10to60°C operating temperatureDR-452445W/2A DIN-rail24VDC power supply with universal85to264VAC or120to370VDC input,-10to50°C operating temperatureDR-75-2475W/3.2A DIN-rail24VDC power supply with universal85to264VAC or120to370VDC input,-10to60°C operating temperatureMDR-40-24DIN-rail24VDC power supply with40W/1.7A,85to264VAC,or120to370VDC input,-20to70°Coperating temperatureMDR-60-24DIN-rail24VDC power supply with60W/2.5A,85to264VAC,or120to370VDC input,-20to70°Coperating temperatureWall-Mounting KitsWK-46Wall-mounting kit,2plates,8screws,46.5x66.8x1mmRack-Mounting KitsRK-4U19-inch rack-mounting kitSoftwareMXview-50Industrial network management software with a license for50nodes(by IP address)MXview-100Industrial network management software with a license for100nodes(by IP address)MXview-250Industrial network management software with a license for250nodes(by IP address)MXview-500Industrial network management software with a license for500nodes(by IP address)MXview-1000Industrial network management software with a license for1000nodes(by IP address)MXview-2000Industrial network management software with a license for2000nodes(by IP address)MXview Upgrade-50License expansion of MXview industrial network management software by50nodes(by IP address)©Moxa Inc.All rights reserved.Updated Sep10,2019.This document and any portion thereof may not be reproduced or used in any manner whatsoever without the express written permission of Moxa Inc.Product specifications subject to change without notice.Visit our website for the most up-to-date product information.。
MOXA EDS-208A系列8口无管理以太网交换机特性与优势说明书
EDS-208A Series8-port unmanaged Ethernet switchesFeatures and Benefits•10/100BaseT(X)(RJ45connector),100BaseFX(multi/single-mode,SC or STconnector)•Redundant dual12/24/48VDC power inputs•IP30aluminum housing•Rugged hardware design well suited for hazardous locations(Class1Div.2/ATEX Zone2),transportation(NEMA TS2/EN50121-4/e-Mark),and maritimeenvironments(DNV/GL/LR/ABS/NK)•-40to75°C operating temperature range(-T models)CertificationsIntroductionThe EDS-208A Series8-port industrial Ethernet switches support IEEE802.3and IEEE802.3u/x with10/100M full/half-duplex,MDI/MDI-X auto-sensing.The EDS-208A Series has12/24/48VDC(9.6to60VDC)redundant power inputs that can be connected simultaneously to live DC power sources.These switches have been designed for harsh industrial environments,such as in maritime(DNV/GL/LR/ABS/NK),rail wayside,highway, or mobile applications(EN50121-4/NEMA TS2/e-Mark),or hazardous locations(Class I Div.2,ATEX Zone2)that comply with FCC,UL,and CE standards.The EDS-208A switches are available with a standard operating temperature range from-10to60°C,or with a wide operating temperature range from-40to75°C.All models are subjected to a100%burn-in test to ensure that they fulfill the special needs of industrial automation control applications.In addition,the EDS-208A switches have DIP switches for enabling or disabling broadcast storm protection,providing another level of flexibility for industrial applications.SpecificationsEthernet Interface10/100BaseT(X)Ports(RJ45connector)EDS-208A/208A-T:8EDS-208A-M-SC/M-ST/S-SC Series:7EDS-208A-MM-SC/MM-ST/SS-SC Series:6All models support:Auto negotiation speedFull/Half duplex modeAuto MDI/MDI-X connection100BaseFX Ports(multi-mode SC connector)EDS-208A-M-SC Series:1EDS-208A-MM-SC Series:2100BaseFX Ports(multi-mode ST connector)EDS-208A-M-ST Series:1EDS-208A-MM-ST Series:2100BaseFX Ports(single-mode SC connector)EDS-208A-S-SC Series:1EDS-208A-SS-SC Series:2Standards IEEE802.3for10BaseTIEEE802.3u for100BaseT(X)and100BaseFXIEEE802.3x for flow controlOptical Fiber800Typical Distance4km5km40kmWavelength Typical(nm)13001310TX Range(nm)1260to13601280to1340 RX Range(nm)1100to16001100to1600Optical Power TX Range(dBm)-10to-200to-5 RX Range(dBm)-3to-32-3to-34 Link Budget(dB)1229 Dispersion Penalty(dB)31Note:When connecting a single-mode fiber transceiver,we recommend using anattenuator to prevent damage caused by excessive optical power.Note:Compute the“typical distance”of a specific fiber transceiver as follows:Linkbudget(dB)>dispersion penalty(dB)+total link loss(dB).Switch PropertiesMAC Table Size2KPacket Buffer Size768kbitsProcessing Type Store and ForwardPower ParametersConnection1removable4-contact terminal block(s)Input Current EDS-208A/208A-T,EDS-208A-M-SC/M-ST/S-SC Series:0.11A@24VDCEDS-208A-MM-SC/MM-ST/SS-SC Series:0.15A@24VDCInput Voltage12/24/48VDC,Redundant dual inputsOperating Voltage9.6to60VDCOverload Current Protection SupportedReverse Polarity Protection SupportedDIP Switch ConfigurationEthernet Interface Broadcast storm protectionPhysical CharacteristicsHousing AluminumIP Rating IP30Dimensions50x114x70mm(1.96x4.49x2.76in)Weight275g(0.61lb)Installation DIN-rail mounting,Wall mounting(with optional kit)Environmental LimitsOperating Temperature Standard Models:-10to60°C(14to140°F)Wide Temp.Models:-40to75°C(-40to167°F) Storage Temperature(package included)-40to85°C(-40to185°F)Ambient Relative Humidity5to95%(non-condensing)Standards and CertificationsEMC EN55032/24EMI CISPR32,FCC Part15B Class AEMS IEC61000-4-2ESD:Contact:6kV;Air:8kVIEC61000-4-3RS:80MHz to1GHz:10V/mIEC61000-4-4EFT:Power:2kV;Signal:1kVIEC61000-4-5Surge:Power:2kV;Signal:2kVIEC61000-4-6CS:10VIEC61000-4-8PFMFHazardous Locations ATEX,Class I Division2Maritime ABS,DNV-GL,LR,NKRailway EN50121-4Safety UL508Shock IEC60068-2-27Traffic Control NEMA TS2Vibration IEC60068-2-6Freefall IEC60068-2-31MTBFTime2,701,531hrsStandards Telcordia(Bellcore),GBWarrantyWarranty Period5yearsDetails See /warrantyPackage ContentsDevice1x EDS-208A Series switchDocumentation1x quick installation guide1x warranty cardDimensionsOrdering InformationModel Name 10/100BaseT(X)PortsRJ45Connector100BaseFX PortsMulti-Mode,SCConnector100BaseFX PortsMulti-Mode,STConnector100BaseFX PortsSingle-Mode,SCConnectorOperating Temp.EDS-208A8–––-10to60°C EDS-208A-T8–––-40to75°C EDS-208A-M-SC71––-10to60°C EDS-208A-M-SC-T71––-40to75°C EDS-208A-M-ST7–1–-10to60°C EDS-208A-M-ST-T7–1–-40to75°C EDS-208A-MM-SC62––-10to60°C EDS-208A-MM-SC-T62––-40to75°C EDS-208A-MM-ST6–2–-10to60°C EDS-208A-MM-ST-T6–2–-40to75°C EDS-208A-S-SC7––1-10to60°C EDS-208A-S-SC-T7––1-40to75°C EDS-208A-SS-SC6––2-10to60°C EDS-208A-SS-SC-T6––2-40to75°C Accessories(sold separately)Power SuppliesDR-120-24120W/2.5A DIN-rail24VDC power supply with universal88to132VAC or176to264VAC input byswitch,or248to370VDC input,-10to60°C operating temperatureDR-452445W/2A DIN-rail24VDC power supply with universal85to264VAC or120to370VDC input,-10to50°C operating temperatureDR-75-2475W/3.2A DIN-rail24VDC power supply with universal85to264VAC or120to370VDC input,-10to60°C operating temperatureMDR-40-24DIN-rail24VDC power supply with40W/1.7A,85to264VAC,or120to370VDC input,-20to70°Coperating temperatureMDR-60-24DIN-rail24VDC power supply with60W/2.5A,85to264VAC,or120to370VDC input,-20to70°Coperating temperatureWall-Mounting KitsWK-30Wall-mounting kit,2plates,4screws,40x30x1mmWK-46Wall-mounting kit,2plates,8screws,46.5x66.8x1mmRack-Mounting KitsRK-4U19-inch rack-mounting kit©Moxa Inc.All rights reserved.Updated Jan30,2019.This document and any portion thereof may not be reproduced or used in any manner whatsoever without the express written permission of Moxa Inc.Product specifications subject to change without notice.Visit our website for the most up-to-date product information.。
MOXA交换机使用说明教学内容
M O X A交换机使用说明MOXA交换机使用说明1、IP地址的设置通过IE工具来Ping 交换机默认的IP(出厂默认192.168.127.253)地址，进入交换机配置界面后，直接点击确认后，进入交换机设置界面对话框，IP地址设置请选择\Main Meun\Basic Settings\Network，出现下列对话框在此对话框下，设置人员在Switch IP Address 和 Switch Subnet Mask 旁的空白处填写预定的IP地址（如：192.168.12.20），以及相应的子网掩码地址（如：255.255.255.0）；其他的如Auto IP Configuration 设置为Disable方式，不要选择HDCP方式。
2、主站（Master）设置完成了IP方式的设置后，就需要对交换的通讯协议和交换机进行相应的设置，选择\Main Menu\Communication Redundancy（通讯冗余设置），进入对话框：在此对话框内，我们需要注意的是Settings标记下方的设置参量，而Current Status为相应的设置参量后交换机系统检测后的状态指示。
Redundancy Protocol （通讯协议设置）：设置选择为Turbo Ring ，而非是IEEE802协议（快速生成树）方式；采用Turbo Ring方式的情况下，需要在网络交换机组中设置一个Master（主站），选择主站的方式是将Set as Master前的小方框内给予选中, 只需要选择确定后，点击Activate按钮即可生效。
（注意：在多个交换机组成网中只能有1个设置为Master，不可以多选；同时如果不对交换机进行Master设置，系统会自动设置交换机组中的1台为Master）。
Enable Ring Coupling （环间耦合端口定义）在实际的项目运用中不常运用到，在此不给予更多的描述。
需要提醒的是工程人员在设置过程中不要将Enable Ring Coupling前的小方格选中，同时要注意的是对应的Coupling Port和 Coupling Control Port后的端口与前面的Redundant Ports 1st Port和 2nd Port（冗余连接端口定义）设置的端口重复。
MOXA交换机使用说明
MOXA接换机使用证明之阳早格格创做1、IP天面的树立通过IE工具去Ping 接换机默认的IP(出厂默认192.168.127.253)天面，加进接换机摆设界里后，间接面打确认后，加进接换机树立界里对付话框，IP天面树立请采用\Main Meun\Basic Settings\Network，出现下列对付话框正在此对付话框下，树立人员正在Switch IP Address 战Switch Subnet Mask 旁的空黑处挖写预约的IP天面（如：192.168.12.20），以及相映的子网掩码天面（如：255.255.255.0）；其余的如Auto IP Configuration 树立为Disable办法，没有要采用HDCP办法.2、主站（Master）树立完毕了IP办法的树立后，便需要对付接换的通讯协媾战接换机举止相映的树立，采用\Main Menu\Communication Redundancy（通讯冗余树立），加进对付话框：正在此对付话框内，咱们需要注意的是Settings标记表记标帜下圆的树立参量，而Current Status为相映的树立参量后接换机系统检测后的状态指示.Redundancy Protocol （通讯协议树立）：树立采用为Turbo Ring ，而非是IEEE802协议（赶快死成树）办法；采与Turbo Ring办法的情况下，需要正在搜集接换机组中树立一个Master（主站），采用主站的办法是将Set as Master前的小圆框内赋予选中, 只需要采用决定后，面打Activate按钮即可死效.（注意：正在多个接换机组成网中只可有1个树立为Master，没有成以多选；共时如果分歧过失接换机举止Master树立，系统会自动树立接换机组中的1台为Master）.Enable Ring Coupling （环间耦合端心定义）正在本质的名目使用中没有常使用到，正在此没有赋予更多的形貌.需要指示的是工程人员正在树立历程中没有要将Enable Ring Coupling前的小圆格选中，共时要注意的是对付应的Coupling Port战Coupling Control Port后的端心与前里的Redundant Ports 1st Port战 2nd Port（冗余对接端心定义）树立的端心沉复.3、搜集树立参数考证完毕搜集参数树立后，对付应的Communication Redundancy对付话框内皆通过Current Status状态赋予体现了，包罗了搜集协议状态、主（Master）/从（Slave）办法；冗余端心的数据监测状态以及环间耦合状态疑息.正在多台接换机组环的情况下，工程人员要注意Redundant Ports 1st Port战2nd Port（冗余端心状态监测状态）的疑息：（1）、Forwarding:（促成状态）表示接换机的处事状态平常，二个搜集冗余对接端心的数据进程宁静.（2）、Link Down：（断线状态）表示接换机于相映的对接心对接的数据线存留问题，引导系统监测到为断线状态，需要工程人员举止查看.（3）、Blocked:（中断状态）此状态为平常情景，果为Turbo Ring办法正在物理上以环的形式存留，而正在接换机搜集接换时，是通过一面的Blocked标记表记标帜去标注环网的假制末面，以决定其数据流背的末面.（4）、Learning：（侦听状态）此状态正在搜集出现了断线战回复的历程中，后备线路的接换机会出现侦听状态，正在稳态的情况下，接换机没有会出现此疑息.正在参数树立完毕战搜集回复佳后，请查看各接换机的冗余端心状态，平常情景为惟有1台接换机的1个端心处于Blocked状态，其余接换机及其端心为Forwarding状态.4、搜集尝试考证对付于搜集接换机及搜集线树立对接完毕后，请工程人员测验考查将搜集冗余线的环赋予断启，以考证搜集接换机的运止处事情景怎么样.5、闭于冗余心的对接办法（1）、齐电心的接换机的对接：诸如408A系列中齐电心的，精确的冗余端心对接办法为：端心7与端心8对接，接互对接产死环形办法.（2）、光心型接换机的对接办法，诸如：408A、516A系列中SC（ST）型号的设备，精确的冗余端心对接办法如下：光心接换机1的T1对接光心接换机2的R2，R1对接T2，T2对接R1，R2对接T1；多台接换依此对接办法逆延对接，并最后产死环形结构.依照非平常办法对接，肯定会制成搜集回路的非冗余，共时极有大概果搜集数据接换的果素引导搜集没有宁静或者搜集风暴局里出现，请诸位工程人员庄重遵照精确要领举止对接.。
MOXA EDS-518A 18口Managed Ethernet交换机用户指南说明书
EDS-518A Series16+2G-port Gigabit managed EthernetswitchesFeatures and Benefits•2Gigabit plus16Fast Ethernet ports for copper and fiber•Turbo Ring and Turbo Chain(recovery time<20ms@250switches),1RSTP/ STP,and MSTP for network redundancy•TACACS+,SNMPv3,IEEE802.1X,HTTPS,and SSH to enhance network security•Easy network management by web browser,CLI,Telnet/serial console, Windows utility,and ABC-01CertificationsIntroductionThe EDS-518A standalone18-port managed Ethernet switches provide2combo Gigabit ports with built-in RJ45or SFP slots for Gigabit fiber-optic communication.The Ethernet redundancy technologies Turbo Ring and Turbo Chain(recovery time<20ms)increase the reliability and speed of your network backbone.The EDS-518A switches also support advanced management and security features.Additional Features and Benefits•Command line interface(CLI)for quickly configuring majormanaged functions•DHCP Option82for IP address assignment with different policies•Supports EtherNet/IP and Modbus TCP protocols for devicemanagement and monitoring•Compatible with PROFINET protocol for transparent datatransmission•Supports the ABC-01-USB(Automatic Backup Configurator)forsystem configuration backup•IGMP snooping and GMRP for filtering multicast traffic•Port-based VLAN,IEEE802.1Q VLAN,and GVRP to ease networkplanning•QoS(IEEE802.1p and TOS/DiffServ)to increase determinism•Port Trunking for optimum bandwidth utilization•SNMPv1/v2c/v3for different levels of network management•RMON for proactive and efficient network monitoring•Bandwidth management to prevent unpredictable network status•Automatic warning by exception through email and relay outputSpecificationsInput/Output InterfaceAlarm Contact Channels Resistive load:1A@24VDCDigital Inputs+13to+30V for state1-30to+3V for state0Max.input current:8mAEthernet Interface10/100BaseT(X)Ports(RJ45connector)EDS-518A/518A-T:16EDS-518A-MM-SC/MM-ST/SS-SC Series:14EDS-518A-SS-SC-80:14All models support:Auto negotiation speedFull/Half duplex modeAuto MDI/MDI-X connection100BaseFX Ports(multi-mode SC connector)EDS-518A-MM-SC Series:21.Gigabit Ethernet recovery time<50ms100BaseFX Ports(multi-mode ST connector)EDS-518A-MM-ST Series:2100BaseFX Ports(single-mode SC connector)EDS-518A-SS-SC Series:2100BaseFX Ports,Single-Mode SC Connector,80kmEDS-518A-SS-SC-80Series:2Combo Ports(10/100/1000BaseT(X)or1000BaseSFP)2Optical Fiber800Typical Distance4km5km40kmWavelength Typical(nm)13001310TX Range(nm)1260to13601280to1340 RX Range(nm)1100to16001100to1600Optical Power TX Range(dBm)-10to-200to-5 RX Range(dBm)-3to-32-3to-34 Link Budget(dB)1229 Dispersion Penalty(dB)31Note:When connecting a single-mode fiber transceiver,we recommend using anattenuator to prevent damage caused by excessive optical power.Note:Compute the“typical distance”of a specific fiber transceiver as follows:Linkbudget(dB)>dispersion penalty(dB)+total link loss(dB).Standards IEEE802.3for10BaseTIEEE802.3u for100BaseT(X)and100BaseFXIEEE802.3ab for1000BaseT(X)IEEE802.3z for1000BaseSX/LX/LHX/ZXIEEE802.1X for authenticationIEEE802.1D-2004for Spanning Tree ProtocolIEEE802.1w for Rapid Spanning Tree ProtocolIEEE802.1s for Multiple Spanning Tree ProtocolIEEE802.1Q for VLAN TaggingIEEE802.1p for Class of ServiceIEEE802.3x for flow controlIEEE802.3ad for Port Trunk with LACPEthernet Software FeaturesFilter802.1Q VLAN,Port-based VLAN,IGMP v1/v2,GVRP,GMRPIndustrial Protocols EtherNet/IP,Modbus TCPManagement IPv4/IPv6,SNMPv1/v2c/v3,LLDP,Port Mirror,Back Pressure Flow Control,BOOTP,DDM,DHCP Option66/67/82,DHCP Server/Client,Flow control,RARP,RMON,SMTP,SNMP Inform,Syslog,Telnet,TFTPMIB MIB-II,Bridge MIB,Ethernet-like MIB,P-BRIDGE MIB,Q-BRIDGE MIB,RMON MIBGroups1,2,3,9,RSTP MIBRedundancy Protocols STP,MSTP,RSTP,LACP,Link Aggregation,Turbo Chain,Turbo Ring v1/v2Security HTTPS/SSL,TACACS+,Port Lock,RADIUS,SSH,Broadcast storm protectionTime Management NTP Server/Client,SNTPSwitch PropertiesIGMP Groups256MAC Table Size8KMax.No.of VLANs64Packet Buffer Size2MbitsPriority Queues4VLAN ID Range VID1to4094LED InterfaceLED Indicators PWR1,PWR2,FAULT,10/100M(TP port),100M(fiber port),1000M(Gigabit port),MSTR/HEAD,CPLR/TAILSerial InterfaceConsole Port RS-232(TxD,RxD,GND),8-pin RJ45(115200,n,8,1)DIP Switch ConfigurationEthernet Interface Turbo Ring,Master,Coupler,ReservePower ParametersConnection2removable6-contact terminal block(s)Input Current EDS-518A/518A-T:0.44A@24VDCEDS-518A-MM-SC/MM-ST/SS-SC Series:0.52A@24VDCEDS-518A-SS-SC-80:0.52A@24VDCInput Voltage24VDC,Redundant dual inputsOperating Voltage12to45VDCOverload Current Protection SupportedReverse Polarity Protection SupportedPhysical CharacteristicsHousing MetalIP Rating IP30Dimensions94x135x142.7mm(3.7x5.31x5.62in)Weight1630g(3.60lb)Installation DIN-rail mounting,Wall mounting(with optional kit)Environmental LimitsOperating Temperature Standard Models:0to60°C(32to140°F)Wide Temp.Models:-40to75°C(-40to167°F)Storage Temperature(package included)-40to85°C(-40to185°F)Ambient Relative Humidity5to95%(non-condensing)Standards and CertificationsSafety EN60950-1,UL60950-1,CSA C22.2No.60950-1,UL508Hazardous Locations ATEX,Class I Division2EMC EN55032/24EMI CISPR32,FCC Part15B Class AEMS IEC61000-4-2ESD:Contact:6kV;Air:8kVIEC61000-4-3RS:80MHz to1GHz:10V/mIEC61000-4-4EFT:Power:1kV;Signal:0.5kVIEC61000-4-5Surge:Power:2kV;Signal:1kVIEC61000-4-6CS:10VIEC61000-4-8PFMFMaritime DNV-GL,NKShock IEC60068-2-27Vibration IEC60068-2-6Freefall IEC60068-2-31MTBFTime250,966hrsStandards Telcordia(Bellcore),GBWarrantyWarranty Period5yearsDetails See /warrantyPackage ContentsDevice1x EDS-518A Series switchCable1x DB9female to RJ4510-pinInstallation Kit4x cap,plastic,for RJ45port2x cap,plastic,for SFP slot2x cap,plastic,for SC fiber port(-SC models)2x cap,plastic,for ST fiber port(-ST models)Documentation1x document and software CD1x quick installation guide1x warranty card1x product certificates of quality inspection,Simplified Chinese1x product notice,Simplified ChineseNote SFP modules need to be purchased separately for use with this product.Dimensions Ordering InformationModel Name 10/100BaseT(X)PortsRJ45ConnectorCombo Ports10/100/1000BaseT(X)or1000BaseSFP100BaseFXPortsMulti-Mode,SCConnector100BaseFXPortsMulti-Mode,STConnector100BaseFXPortsSingle-Mode,SCConnector100BaseFXPortsSingle-Mode,SCConnector,80kmOperating Temp.EDS-518A162––––0to60°C EDS-518A-T162––––-40to75°C EDS-518A-MM-SC1422–––0to60°C EDS-518A-MM-SC-T1422–––-40to75°C EDS-518A-MM-ST142–2––0to60°C EDS-518A-MM-ST-T142–2––-40to75°C EDS-518A-SS-SC142––2–0to60°C EDS-518A-SS-SC-T142––2–-40to75°C EDS-518A-SS-SC-80142–––20to60°C Accessories(sold separately)Storage KitsABC-01Configuration backup and restoration tool for managed Ethernet switches and AWK Series wirelessAPs/bridges/clients,0to60°C operating temperatureSFP ModulesSFP-1G10ALC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for10km transmission;TX1310nm,RX1550nm,0to60°C operating temperatureSFP-1G10ALC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for10km transmission;TX1310nm,RX1550nm,-40to85°C operating temperatureSFP-1G10BLC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for10km transmission;TX1550nm,RX1310nm,0to60°C operating temperatureSFP-1G10BLC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for10km transmission;TX1550nm,RX1310nm,-40to85°C operating temperatureSFP-1G20ALC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for20km transmission;TX1310nm,RX1550nm,0to60°C operating temperatureSFP-1G20ALC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for20km transmission;TX1310nm,RX1550nm,-40to85°C operating temperatureSFP-1G20BLC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for20km transmission;TX1550nm,RX1310nm,0to60°C operating temperatureSFP-1G20BLC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for20km transmission;TX1550nm,RX1310nm,-40to85°C operating temperatureSFP-1G40ALC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for40km transmission;TX1310nm,RX1550nm,0to60°C operating temperatureSFP-1G40ALC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for40km transmission;TX1310nm,RX1550nm,-40to85°C operating temperatureSFP-1G40BLC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for40km transmission;TX1550nm,RX1310nm,0to60°C operating temperatureSFP-1G40BLC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for40km transmission;TX1550nm,RX1310nm,-40to85°C operating temperatureSFP-1GEZXLC SFP module with11000BaseEZX port with LC connector for110km transmission,0to60°C operatingtemperatureSFP-1GEZXLC-120SFP module with11000BaseEZX port with LC connector for120km transmission,0to60°C operatingtemperatureSFP-1GLHLC SFP module with11000BaseLH port with LC connector for30km transmission,0to60°C operatingtemperatureSFP-1GLHLC-T SFP module with11000BaseLH port with LC connector for30km transmission,-40to85°C operatingtemperatureSFP-1GLHXLC SFP module with11000BaseLHX port with LC connector for40km transmission,0to60°C operatingtemperatureSFP-1GLHXLC-T SFP module with11000BaseLHX port with LC connector for40km transmission,-40to85°Coperating temperatureSFP-1GLSXLC SFP module with11000BaseLSX port with LC connector for500m transmission,0to60°C operatingtemperatureSFP-1GLSXLC-T SFP module with11000BaseLSX port with LC connector for500m transmission,-40to85°Coperating temperatureSFP-1GLXLC SFP module with11000BaseLX port with LC connector for10km transmission,0to60°C operatingtemperatureSFP-1GLXLC-T SFP module with11000BaseLX port with LC connector for10km transmission,-40to85°C operatingtemperatureSFP-1GSXLC SFP module with11000BaseSX port with LC connector for300/550m transmission,0to60°Coperating temperatureSFP-1GSXLC-T SFP module with11000BaseSX port with LC connector for300/550m transmission,-40to85°Coperating temperatureSFP-1GZXLC SFP module with11000BaseZX port with LC connector for80km transmission,0to60°C operatingtemperatureSFP-1GZXLC-T SFP module with11000BaseZX port with LC connector for80km transmission,-40to85°C operatingtemperaturePower SuppliesDR-120-24120W/2.5A DIN-rail24VDC power supply with universal88to132VAC or176to264VAC input byswitch,or248to370VDC input,-10to60°C operating temperatureDR-452445W/2A DIN-rail24VDC power supply with universal85to264VAC or120to370VDC input,-10to50°C operating temperatureDR-75-2475W/3.2A DIN-rail24VDC power supply with universal85to264VAC or120to370VDC input,-10to60°C operating temperatureMDR-40-24DIN-rail24VDC power supply with40W/1.7A,85to264VAC,or120to370VDC input,-20to70°Coperating temperatureMDR-60-24DIN-rail24VDC power supply with60W/2.5A,85to264VAC,or120to370VDC input,-20to70°Coperating temperatureWall-Mounting KitsWK-46Wall-mounting kit,2plates,8screws,46.5x66.8x1mmRack-Mounting KitsRK-4U19-inch rack-mounting kitSoftwareMXview-50Industrial network management software with a license for50nodes(by IP address)MXview-100Industrial network management software with a license for100nodes(by IP address)MXview-250Industrial network management software with a license for250nodes(by IP address)MXview-500Industrial network management software with a license for500nodes(by IP address)MXview-1000Industrial network management software with a license for1000nodes(by IP address)MXview-2000Industrial network management software with a license for2000nodes(by IP address)MXview Upgrade-50License expansion of MXview industrial network management software by50nodes(by IP address)©Moxa Inc.All rights reserved.Updated Aug06,2019.This document and any portion thereof may not be reproduced or used in any manner whatsoever without the express written permission of Moxa Inc.Product specifications subject to change without notice.Visit our website for the most up-to-date product information.。
MOXA EDS-208A系列8口无管理Ethernet交换机产品介绍说明书
EDS-208A Series8-port compact unmanaged Ethernet switchesFeatures and Benefits•10/100BaseT(X)(RJ45connector),100BaseFX(multi/single-mode,SC or STconnector)•Redundant dual12/24/48VDC power inputs•IP30aluminum housing•Rugged hardware design well suited for hazardous locations(Class1Div.2/ATEX Zone2),transportation(NEMA TS2/EN50121-4),and maritimeenvironments(DNV/LR/ABS/NK)•-40to75°C wide operating temperature range(-T models)CertificationsIntroductionThe EDS-208A Series8-port industrial Ethernet switches support IEEE802.3and IEEE802.3u/x with10/100M full/half-duplex,MDI/MDI-X auto-sensing.The EDS-208A Series has12/24/48VDC(9.6to60VDC)redundant power inputs that can be connected simultaneously to live DC power sources.These switches have been designed for harsh industrial environments,such as in maritime(DNV/GL/LR/ABS/NK),rail wayside,highway, or mobile applications(EN50121-4/NEMA TS2/e-Mark),or hazardous locations(Class I Div.2,ATEX Zone2)that comply with FCC,UL,and CE standards.The EDS-208A switches are available with a standard operating temperature range from-10to60°C,or with a wide operating temperature range from-40to75°C.All models are subjected to a100%burn-in test to ensure that they fulfill the special needs of industrial automation control applications.In addition,the EDS-208A switches have DIP switches for enabling or disabling broadcast storm protection,providing another level of flexibility for industrial applications.SpecificationsEthernet Interface10/100BaseT(X)Ports(RJ45connector)EDS-208A/208A-T:8EDS-208A-M-SC/M-ST/S-SC Series:7EDS-208A-MM-SC/MM-ST/SS-SC Series:6All models support:Auto negotiation speedFull/Half duplex modeAuto MDI/MDI-X connection100BaseFX Ports(multi-mode SC connector)EDS-208A-M-SC Series:1EDS-208A-MM-SC Series:2100BaseFX Ports(multi-mode ST connector)EDS-208A-M-ST Series:1EDS-208A-MM-ST Series:2100BaseFX Ports(single-mode SC connector)EDS-208A-S-SC Series:1EDS-208A-SS-SC Series:2Standards IEEE802.3for10BaseTIEEE802.3u for100BaseT(X)and100BaseFXIEEE802.3x for flow controlOptical Fiber800Typical Distance4km5km40kmWavelengthTypical(nm)13001310TX Range(nm)1260to13601280to1340 RX Range(nm)1100to16001100to1600Optical PowerTX Range(dBm)-10to-200to-5 RX Range(dBm)-3to-32-3to-34 Link Budget(dB)1229 Dispersion Penalty(dB)31Note:When connecting a single-mode fiber transceiver,we recommend using anattenuator to prevent damage caused by excessive optical power.Note:Compute the“typical distance”of a specific fiber transceiver as follows:Linkbudget(dB)>dispersion penalty(dB)+total link loss(dB).Switch PropertiesMAC Table Size2KPacket Buffer Size768kbitsProcessing Type Store and ForwardPower ParametersConnection1removable4-contact terminal block(s)Input Current EDS-208A/208A-T,EDS-208A-M-SC/M-ST/S-SC Series:0.11A@24VDCEDS-208A-MM-SC/MM-ST/SS-SC Series:0.15A@24VDCInput Voltage12/24/48VDCRedundant dual inputsOperating Voltage9.6to60VDCOverload Current Protection SupportedReverse Polarity Protection SupportedDIP Switch ConfigurationEthernet Interface Broadcast storm protectionPhysical CharacteristicsHousing AluminumIP Rating IP30Dimensions50x114x70mm(1.96x4.49x2.76in)Weight275g(0.61lb)Installation DIN-rail mountingWall mounting(with optional kit) Environmental LimitsOperating Temperature Standard Models:-10to60°C(14to140°F)Wide Temp.Models:-40to75°C(-40to167°F) Storage Temperature(package included)-40to85°C(-40to185°F)Ambient Relative Humidity5to95%(non-condensing)Standards and CertificationsEMC EN55032/24EMI CISPR32,FCC Part15B Class AEMS IEC61000-4-2ESD:Contact:6kV;Air:8kVIEC61000-4-3RS:80MHz to1GHz:10V/mIEC61000-4-4EFT:Power:2kV;Signal:1kVIEC61000-4-5Surge:Power:2kV;Signal:2kVIEC61000-4-6CS:10VIEC61000-4-8PFMFHazardous Locations ATEXClass I Division2Maritime ABSLRNKDNVRailway EN50121-4Safety UL508Shock IEC60068-2-27Traffic Control NEMA TS2Vibration IEC60068-2-6Freefall IEC60068-2-31MTBFTime2,701,531hrsStandards Telcordia(Bellcore),GBWarrantyWarranty Period5yearsDetails See /warrantyPackage ContentsDevice1x EDS-208A Series switchDocumentation1x quick installation guide1x warranty cardDimensionsOrdering InformationModel Name 10/100BaseT(X)PortsRJ45Connector100BaseFX PortsMulti-Mode,SCConnector100BaseFX PortsMulti-Mode,STConnector100BaseFX PortsSingle-Mode,SCConnectorOperating Temp.EDS-208A8–––-10to60°C EDS-208A-T8–––-40to75°C EDS-208A-M-SC71––-10to60°C EDS-208A-M-SC-T71––-40to75°C EDS-208A-M-ST7–1–-10to60°C EDS-208A-M-ST-T7–1–-40to75°C EDS-208A-MM-SC62––-10to60°C EDS-208A-MM-SC-T62––-40to75°C EDS-208A-MM-ST6–2–-10to60°C EDS-208A-MM-ST-T6–2–-40to75°C EDS-208A-S-SC7––1-10to60°C EDS-208A-S-SC-T7––1-40to75°C EDS-208A-SS-SC6––2-10to60°C EDS-208A-SS-SC-T6––2-40to75°C Accessories(sold separately)Power SuppliesDR-120-24120W/2.5A DIN-rail24VDC power supply with universal88to132VAC or176to264VAC input byswitch,or248to370VDC input,-10to60°C operating temperatureDR-452445W/2A DIN-rail24VDC power supply with universal85to264VAC or120to370VDC input,-10to50°C operating temperatureDR-75-2475W/3.2A DIN-rail24VDC power supply with universal85to264VAC or120to370VDC input,-10to60°C operating temperatureMDR-40-24DIN-rail24VDC power supply with40W/1.7A,85to264VAC,or120to370VDC input,-20to70°Coperating temperatureMDR-60-24DIN-rail24VDC power supply with60W/2.5A,85to264VAC,or120to370VDC input,-20to70°Coperating temperatureWall-Mounting KitsWK-30Wall-mounting kit,2plates,4screws,30x66.8x2mmWK-46-01Wall-mounting kit,2plates,8screws,46x66.8x2mmRack-Mounting KitsRK-4U19-inch rack-mounting kit©Moxa Inc.All rights reserved.Updated Jul19,2023.This document and any portion thereof may not be reproduced or used in any manner whatsoever without the express written permission of Moxa Inc.Product specifications subject to change without notice.Visit our website for the most up-to-date product information.。
MOXA交换机使用说明
MOXA交换机使用说明1、IP地址的设置通过IE工具来Ping 交换机默认的IP(出厂默认192.168.127.253)地址，进入交换机配置界面后，直接点击确认后，进入交换机设置界面对话框，IP地址设置请选择\Main Meun\Basic Settings\Network，出现下列对话框在此对话框下，设置人员在Switch IP Address 和 Switch Subnet Mask 旁的空白处填写预定的IP地址（如：192.168.12.20），以及相应的子网掩码地址（如：255.255.255.0）；其他的如Auto IP Configuration 设置为Disable方式，不要选择HDCP方式。
2、主站（Master）设置完成了IP方式的设置后，就需要对交换的通讯协议和交换机进行相应的设置，选择\Main Menu\Communication Redundancy（通讯冗余设置），进入对话框：在此对话框内，我们需要注意的是Settings标记下方的设置参量，而Current Status为相应的设置参量后交换机系统检测后的状态指示。
Redundancy Protocol （通讯协议设置）：设置选择为Turbo Ring ，而非是IEEE802协议（快速生成树）方式；采用Turbo Ring方式的情况下，需要在网络交换机组中设置一个Master（主站），选择主站的方式是将Set as Master前的小方框内给予选中, 只需要选择确定后，点击Activate按钮即可生效。
（注意：在多个交换机组成网中只能有1个设置为Master，不可以多选；同时如果不对交换机进行Master设置，系统会自动设置交换机组中的1台为Master）。
Enable Ring Coupling （环间耦合端口定义）在实际的项目运用中不常运用到，在此不给予更多的描述。
需要提醒的是工程人员在设置过程中不要将Enable Ring Coupling 前的小方格选中，同时要注意的是对应的Coupling Port和 Coupling Control Port后的端口与前面的Redundant Ports 1st Port和 2nd Port（冗余连接端口定义）设置的端口重复。
MOXA交换机参数配置
交换机参数配置
以EDS-516A交换机为例，将交换机接上24V电源，在1-14 口中任选一口用RJ45网线连接到计算机网卡。 交换机的默认IP为192.168.127.253，将计算机的IP地址设 置为192.168.127.0，然后在浏览器中输入交换机的默认IP地 址192.168.127.253，回车就进入交换机的参数配置界面
默认用户名为admin，默认密码为空，然后点击login进入
进入参数配置主界面
导入参数配置文件步骤：选择Basic Setting / System File Update / Local Import /Export 进入配 置文件导入导出界面
在 Upload Configure Data 一行中选择 Browse ，找到预先备好的配置文件，然后点 击Import ，将配置文件上传到交换机中。
文件上传成功后，交换机自动断开连接。 假如交换机上传的IP地址为 192.168.0.248 ，将计算机的IP改为 192.168.0.1，在浏览器中输入 192.168.0.248 ，再次进入，查看IP等参 数是否正确，配置好的交换机密码一般为 空，或者是METSO的默认密码pw4net ， 也可以在Basic Setting中修改密码。
在 Communication Redundancy 中，蓝圈标出的是定义交换机和交换机 之间通讯的接口，这里用的是16口（光纤）和1口（RJ45）。红圈标出 的是定义两个环网之间通讯的接口（MCS系统只有一个环网，所以未用）
交换机如果有配置参数改动，或者接口变动等，需 要将配置文件导出，以作备用。在 Upload Configure Data 计算机选定的位置
Moxa EDS-516A 系列 16 埠網管型乙太網路交換器簡介说明书
EDS-516A 系列16埠網管型乙太網路交換器特色與優點•支援Turbo Ring 和Turbo Chain （對於250台交換器，復原時間<20ms ），STP/RSTP/MSTP ，實現網路備援•支援TACACS+、SNMPv3、IEEE 802.1X 、HTTPS 和SSH ，強化網路安全•透過網頁瀏覽器、CLI 、Telnet ／序列控制埠、Windows 工具程式和ABC-01輕鬆管理網路•支援MXstudio ，輕鬆進行視覺化工業網路管理認證簡介EDS-516A 獨立16埠管理乙太網路交換器搭載先進的渦輪環和渦輪鏈技術（復原時間<20ms ）、RSTP/STP ，以及MSTP ，可提升工業乙太網路的可靠性和可用性。
此外還提供介於-40至75°C 的寬操作溫度範圍的型號，此交換器支援進階管理與安全功能，因此EDS-516A 交換器適用於任何嚴峻工業環境。
附加特色與優點•命令列介面（CLI ）快速設定主要網管功能•DHCP Option 82適用於以不同原則指派IP 位址•支援EtherNet/IP 和Modbus TCP 通訊協定，以進行裝置管理和監控•相容於PROFINET 通訊協定，可進行透明資料傳輸•鎖定連接埠功能可根據MAC 位址封鎖未經授權的存取•IGMP snooping 和GMRP ，用於篩選多點傳送流量•可基於連接埠實現VLAN 、IEEE 802.1Q VLAN 以及GVRP ，以簡化網路規劃•QoS （IEEE 802.1p/1Q 和TOS/DiffServ ）提高可靠性•網路埠端口聚合功能提供最佳頻寬使用率•RMON 提供主動且有效率的網路監控•SNMPv1/v2c/v3，適用不同層級的網路管理•頻寬管理可防止無法預測的網路狀態•發生例外狀況時透過電子郵件和繼電器輸出自動發出警告規格Input/Output InterfaceAlarm Contact Channels Resistive load:1A @24VDC Digital Inputs+13to +30V for state 1-30to +3V for state 0Max.input current:8mAEthernet Interface10/100BaseT(X)Ports (RJ45connector)EDS-516A Series:16EDS-516A-MM-SC/MM-ST Series:14All models support:Auto negotiation speed Full/Half duplex modeAuto MDI/MDI-X connection100BaseFX Ports (multi-mode SC connector)EDS-516A-MM-SC Series:2100BaseFX Ports (multi-mode ST connector)EDS-516A-MM-ST Series:2Optical Fiber800Typical Distance4km5km40km80kmWavelength Typical(nm)130013101550TX Range(nm)1260to13601280to13401530to1570RX Range(nm)1100to16001100to16001100to1600Optical PowerTX Range(dBm)-10to-200to-50to-5RX Range(dBm)-3to-32-3to-34-3to-34Link Budget(dB)122929DispersionPenalty(dB)311Note:When connecting a single-mode fiber transceiver,we recommend using anattenuator to prevent damage caused by excessive optical power.Note:Compute the“typical distance”of a specific fiber transceiver as follows:Linkbudget(dB)>dispersion penalty(dB)+total link loss(dB).Standards IEEE802.3for10BaseTIEEE802.3u for100BaseT(X)and100BaseFXIEEE802.1X for authenticationIEEE802.1D-2004for Spanning Tree ProtocolIEEE802.1w for Rapid Spanning Tree ProtocolIEEE802.1s for Multiple Spanning Tree ProtocolIEEE802.1Q for VLAN TaggingIEEE802.1p for Class of ServiceIEEE802.3x for flow controlIEEE802.3ad for Port Trunk with LACPEthernet Software FeaturesFilter802.1Q VLAN,GMRP,GVRP,IGMP v1/v2,Port-based VLANIndustrial Protocols EtherNet/IP,Modbus TCPManagement IPv4/IPv6,SNMPv1/v2c/v3,LLDP,Port Mirror,Back Pressure Flow Control,BOOTP,DDM,DHCP Option66/67/82,DHCP Server/Client,Flow control,RARP,RMON,SMTP,SNMP Inform,Syslog,Telnet,TFTPMIB MIB-II,Bridge MIB,Ethernet-like MIB,P-BRIDGE MIB,Q-BRIDGE MIB,RMON MIBGroups1,2,3,9,RSTP MIBRedundancy Protocols STP,MSTP,RSTP,LACP,Link Aggregation,Turbo Chain,Turbo Ring v1/v2Security HTTPS/SSL,RADIUS,TACACS+,Port Lock,SSH,Broadcast storm protectionTime Management NTP Server/Client,SNTP,IEEE1588v2PTP(software-based)Switch PropertiesIGMP Groups256MAC Table Size8KMax.No.of VLANs64Packet Buffer Size2MbitsPriority Queues4VLAN ID Range VID1to4094LED InterfaceLED Indicators PWR1,PWR2,FAULT,10/100M(TP port),100M(fiber port),MSTR/HEAD,CPLR/TAIL Serial InterfaceConsole Port RS-232(TxD,RxD,GND),8-pin RJ45(115200,n,8,1)DIP Switch ConfigurationEthernet Interface Turbo Ring,Master,Coupler,ReservePower ParametersConnection2removable6-contact terminal block(s)Input Voltage24VDC,Redundant dual inputsOperating Voltage12to45VDCInput Current EDS-516A Series:0.35A@24VDCEDS-516A-MM-SC/MM-ST Series:0.44A@24VDCOverload Current Protection SupportedReverse Polarity Protection SupportedPhysical CharacteristicsHousing MetalIP Rating IP30Dimensions94x135x142.7mm(3.7x5.31x5.62in)Weight1586g(3.50lb)Installation DIN-rail mounting,Wall mounting(with optional kit)Environmental LimitsOperating Temperature Standard Models:0to60°C(32to140°F)Wide Temp.Models:-40to75°C(-40to167°F)Storage Temperature(package included)-40to85°C(-40to185°F)Ambient Relative Humidity5to95%(non-condensing)Standards and CertificationsSafety EN60950-1,UL60950-1,CSA C22.2No.60950-1,UL508Hazardous Locations ATEX,Class I Division2EMC EN55032/24EMI CISPR32,FCC Part15B Class AEMS IEC61000-4-2ESD:Contact:6kV;Air:8kVIEC61000-4-3RS:80MHz to1GHz:10V/mIEC61000-4-4EFT:Power:1kV;Signal:0.5kVIEC61000-4-5Surge:Power:2kV;Signal:1kVIEC61000-4-6CS:10VIEC61000-4-8PFMFMaritime DNV-GLShock IEC60068-2-27Vibration IEC60068-2-6Freefall IEC60068-2-31MTBFTime247,676hrsStandards Telcordia(Bellcore),GBWarrantyWarranty Period5yearsDetails See /tw/warrantyPackage ContentsDevice1x EDS-516A Series switchCable1x DB9female to RJ4510-pinInstallation Kit4x cap,plastic,for RJ45port2x cap,plastic,for SC fiber port(-SC models)2x cap,plastic,for ST fiber port(-ST models)Documentation1x quick installation guide1x warranty card1x product certificates of quality inspection,Simplified Chinese1x product notice,Simplified Chinese尺寸訂購資訊EDS-516A16––0to60°CEDS-516A-T16––-40to75°CEDS-516A-MM-SC142–0to60°CEDS-516A-MM-SC-T142–-40to75°CEDS-516A-MM-ST14–20to60°CEDS-516A-MM-ST-T14–2-40to75°C配件（選購）Storage KitsABC-01Configuration backup and restoration tool for managed Ethernet switches and AWK Series wireless APs/bridges/clients,0to60°C operating temperaturePower SuppliesDR-120-24120W/2.5A DIN-rail24VDC power supply with universal88to132VAC or176to264VAC input byswitch,or248to370VDC input,-10to60°C operating temperatureDR-452445W/2A DIN-rail24VDC power supply with universal85to264VAC or120to370VDC input,-10to50°Coperating temperatureDR-75-2475W/3.2A DIN-rail24VDC power supply with universal85to264VAC or120to370VDC input,-10to60°C operating temperatureMDR-40-24DIN-rail24VDC power supply with40W/1.7A,85to264VAC,or120to370VDC input,-20to70°Coperating temperatureMDR-60-24DIN-rail24VDC power supply with60W/2.5A,85to264VAC,or120to370VDC input,-20to70°Coperating temperatureSoftwareMXview-50Industrial network management software with a license for50nodes(by IP address)MXview-100Industrial network management software with a license for100nodes(by IP address)MXview-250Industrial network management software with a license for250nodes(by IP address)MXview-500Industrial network management software with a license for500nodes(by IP address)MXview-1000Industrial network management software with a license for1000nodes(by IP address)MXview-2000Industrial network management software with a license for2000nodes(by IP address)MXview Upgrade-50License expansion of MXview industrial network management software by50nodes(by IP address)Wall-Mounting KitsWK-46Wall-mounting kit,2plates,8screws,46.5x66.8x1mmRack-Mounting KitsRK-4U19-inch rack-mounting kit©Moxa Inc.版權所有.2021年4月15日更新。
MOXA EDS-405A 五口入级管理以太网交换机产品介绍说明书
EDS-405A Series5-port entry-level managed EthernetswitchesFeatures and Benefits•Turbo Ring and Turbo Chain(recovery time<20ms@250switches),and RSTP/STP for network redundancy•IGMP Snooping,QoS,IEEE802.1Q VLAN,and port-based VLAN supported •Easy network management by web browser,CLI,Telnet/serial console, Windows utility,and ABC-01•PROFINET or EtherNet/IP enabled by default(PN or EIP models)•Supports MXstudio for easy,visualized industrial network managementCertificationsIntroductionThe EDS-405A Series is designed especially for industrial applications.The switches support a variety of useful management functions,such as Turbo Ring,Turbo Chain,ring coupling,IGMP snooping,IEEE802.1Q VLAN,port-based VLAN,QoS,RMON,bandwidth management,port mirroring,and warning by email or relay.The ready-to-use Turbo Ring can be set up easily using the web-based management interface,or with the DIP switches located on the top panel of the EDS-405A switches.Additional Features and Benefits•DHCP Option82for IP address assignment with different policies•Supports EtherNet/IP,Modbus TCP and PROFINET1protocols fordevice management and monitoring•EtherNet/IP EDS(Electronic Data Sheet)file,custom AOI(Add-OnInstructions)and FactoryTalk®View faceplate available•PROFINET GSDML file and SIMATIC STEP7device icons available1•Port mirroring for online debugging•Port-based VLAN,IEEE802.1Q VLAN,and GVRP to ease networkplanning•QoS(IEEE802.1p and TOS/DiffServ)to increase determinism•RMON for proactive and efficient network monitoring•SNMPv1/v2c/v3for different levels of network management security•Bandwidth management to prevent unpredictable network status SpecificationsEthernet Interface10/100BaseT(X)Ports(RJ45connector)EDS-405A,405A-EIP/PN/PTP models:5EDS-405A-MM-SC/MM-ST/SS-SC models:3All models support:Auto negotiation speedFull/Half duplex modeAuto MDI/MDI-X connection100BaseFX Ports(multi-mode SC connector)EDS-405A-MM-SC models:2100BaseFX Ports(multi-mode ST connector)EDS-405A-MM-ST models:2100BaseFX Ports(single-mode SC connector)EDS-405A-SS-SC models:21.EDS-405A-PN Series onlyOptical Fiber800Typical Distance4km5km40kmWavelengthTypical(nm)13001310TX Range(nm)1260to13601280to1340 RX Range(nm)1100to16001100to1600Optical PowerTX Range(dBm)-10to-200to-5 RX Range(dBm)-3to-32-3to-34 Link Budget(dB)1229 Dispersion Penalty(dB)31Note:When connecting a single-mode fiber transceiver,we recommend using anattenuator to prevent damage caused by excessive optical power.Note:Compute the“typical distance”of a specific fiber transceiver as follows:Linkbudget(dB)>dispersion penalty(dB)+total link loss(dB).Standards IEEE802.3for10BaseTIEEE802.3u for100BaseT(X)and100BaseFXIEEE802.3x for flow controlIEEE802.1D-2004for Spanning Tree ProtocolIEEE802.1p for Class of ServiceIEEE802.1Q for VLAN TaggingIEEE802.1w for Rapid Spanning Tree ProtocolEthernet Software FeaturesFilter802.1Q VLAN,GMRP,GVRP,IGMP v1/v2,Port-based VLANIndustrial Protocols EtherNet/IP2,Modbus TCPEDS-405A-PN models:PROFINET IO Device(Slave)Management Back Pressure Flow Control,BOOTP,DHCP Option66/67/82,DHCP Server/Client,Flowcontrol,IPv4/IPv6,LLDP,Port Mirror,RARP,RMON,SMTP,SNMP Inform,SNMPv1/v2c/v3,Syslog,Telnet,TFTPMIB Bridge MIB,Ethernet-like MIB,MIB-II,P-BRIDGE MIB,RMON MIB Groups1,2,3,9,RSTP MIBRedundancy Protocols RSTP,STP,Turbo Chain,Turbo Ring v1/v2Time Management All models:NTP Server/Client,SNTPEDS-405A-PTP models:IEEE1588v2PTP(hardware-based)Switch PropertiesIGMP Groups256MAC Table Size EDS-405A,EDS-405A-EIP/MM-SC/MM-ST/PN/SS-SC models:2KEDS-405A-PTP models:8KMax.No.of VLANs64Packet Buffer Size1Mbits2.EDS-405A-EIP Series:EtherNet/IP protocol enabled by default.Priority Queues4VLAN ID Range VID1to4094Serial InterfaceConsole Port RS-232(TxD,RxD,GND),10-pin RJ45(115200,n,8,1)DIP Switch ConfigurationEthernet Interface Turbo Ring,Master,Coupler,ReserveInput/Output InterfaceAlarm Contact Channels Relay output with current carrying capacity of1A@24VDC Power ParametersInput Voltage12/24/48VDC,Redundant dual inputsOperating Voltage9.6to60VDCInput Current EDS-405A,405A-EIP/PN/MM-SC/MM-ST/SS-SC models:0.594A@12VDC0.286A@24VDC0.154A@48VDCEDS-405A-PTP models:0.23A@24VDCOverload Current Protection SupportedReverse Polarity Protection SupportedConnection1removable6-contact terminal block(s)Physical CharacteristicsHousing MetalIP Rating IP30Dimensions53.6x135x105mm(2.11x5.31x4.13in)Weight EDS-405A-EIP/MM-SC/MM-ST/PN/SS-SC models:650g(1.44lb)EDS-405A-PTP models:820g(1.81lb)Installation DIN-rail mounting,Wall mounting(with optional kit) Environmental LimitsOperating Temperature Standard Models:-10to60°C(14to140°F)Wide Temp.Models:-40to75°C(-40to167°F)Storage Temperature(package included)-40to85°C(-40to185°F)Ambient Relative Humidity5to95%(non-condensing)Standards and CertificationsSafety All models:UL508Non-PTP models:UL60950-1EMC EN55032/24EMI CISPR32,FCC Part15B Class AEMS Non-PTP models:IEC61000-4-2ESD:Contact:6kV;Air:8kVIEC61000-4-3RS:80MHz to1GHz:20V/mIEC61000-4-4EFT:Power:2kV;Signal:2kVIEC61000-4-5Surge:Power:2kV;Signal:2kVIEC61000-4-6CS:10VIEC61000-4-8PTP models:IEC61000-4-2ESD:Contact:4kV;Air:8kVIEC61000-4-3RS:80MHz to1GHz:3V/mIEC61000-4-4EFT:Power:0.5kV;Signal:0.5kVIEC61000-4-5Surge:Power:0.5kV;Signal:1kVIEC61000-4-6CS:3VIEC61000-4-8Hazardous Locations Non-PTP models:ATEX,Class I Division2Maritime Non-PTP models:DNVTraffic Control Non-PTP models:NEMA TS2Freefall IEC60068-2-31Shock IEC60068-2-27Vibration IEC60068-2-6MTBFTime EDS-405A,EDS-405A-EIP/PN models:1,547,941hrsEDS-405A-MM-SC/MM-ST/SS-SC models:1,429,327hrsEDS-405A-PTP models:1,316,464hrsStandards Telcordia(Bellcore),GBWarrantyWarranty Period5yearsDetails See /warrantyPackage ContentsDevice1x EDS-405A Series switchCable1x RJ45-to-DB9console cableInstallation Kit2x cap,plastic,for RJ45portDocumentation1x product certificates of quality inspection,Simplified Chinese1x product notice,Simplified Chinese1x quick installation guide1x warranty cardDimensions Ordering InformationModel Name Layer Total No.ofPorts10/100BaseT(X)PortsRJ45Connector100BaseFXPortsMulti-Mode SCConnector100BaseFXPortsMulti-Mode STConnector100BaseFXPortsSingle-Mode SCConnectorOperating Temp.EDS-405A255–––-10to60°C EDS-405A-T255–––-40to75°C EDS-405A-MM-ST253–2–-10to60°C EDS-405A-MM-ST-T253–2–-40to75°C EDS-405A-MM-SC2532––-10to60°C EDS-405A-MM-SC-T2532––-40to75°C EDS-405A-SS-SC253––2-10to60°C EDS-405A-SS-SC-T253––2-40to75°C EDS-405A-EIP255–––-10to60°C EDS-405A-EIP-T255–––-40to75°C EDS-405A-PN255–––-10to60°C EDS-405A-PN-T255–––-40to75°C EDS-405A-PTP255–––-10to60°C EDS-405A-PTP-T255–––-40to75°C Accessories(sold separately)Storage KitsABC-01Configuration backup and restoration tool for managed Ethernet switches and AWK Series wirelessAPs/bridges/clients,0to60°C operating temperaturePower SuppliesDR-120-24120W/2.5A DIN-rail24VDC power supply with universal88to132VAC or176to264VAC input byswitch,or248to370VDC input,-10to60°C operating temperatureDR-452445W/2A DIN-rail24VDC power supply with universal85to264VAC or120to370VDC input,-10to50°C operating temperatureDR-75-2475W/3.2A DIN-rail24VDC power supply with universal85to264VAC or120to370VDC input,-10to60°C operating temperatureMDR-40-24DIN-rail24VDC power supply with40W/1.7A,85to264VAC,or120to370VDC input,-20to70°Coperating temperatureMDR-60-24DIN-rail24VDC power supply with60W/2.5A,85to264VAC,or120to370VDC input,-20to70°Coperating temperatureSoftwareMXview-50Industrial network management software with a license for50nodes(by IP address)MXview-100Industrial network management software with a license for100nodes(by IP address)MXview-250Industrial network management software with a license for250nodes(by IP address)MXview-500Industrial network management software with a license for500nodes(by IP address)MXview-1000Industrial network management software with a license for1000nodes(by IP address)MXview-2000Industrial network management software with a license for2000nodes(by IP address)MXview Upgrade-50License expansion of MXview industrial network management software by50nodes(by IP address) Wall-Mounting KitsWK-46-01Wall-mounting kit,2plates,8screws,46x66.8x2mmRack-Mounting KitsRK-4U19-inch rack-mounting kit©Moxa Inc.All rights reserved.Updated May12,2022.This document and any portion thereof may not be reproduced or used in any manner whatsoever without the express written permission of Moxa Inc.Product specifications subject to change without notice.Visit our website for the most up-to-date product information.。
莫萨 EDS-208A 系列 8 口编程无管理以太网交换机产品介绍说明书
EDS-208A Series8-port compact unmanaged Ethernet switchesFeatures and Benefits•10/100BaseT(X)(RJ45connector),100BaseFX(multi/single-mode,SC or STconnector)•Redundant dual12/24/48VDC power inputs•IP30aluminum housing•Rugged hardware design well suited for hazardous locations(Class1Div.2/ATEX Zone2),transportation(NEMA TS2/EN50121-4),and maritimeenvironments(DNV/LR/ABS/NK)•-40to75°C wide operating temperature range(-T models)CertificationsIntroductionThe EDS-208A Series8-port industrial Ethernet switches support IEEE802.3and IEEE802.3u/x with10/100M full/half-duplex,MDI/MDI-X auto-sensing.The EDS-208A Series has12/24/48VDC(9.6to60VDC)redundant power inputs that can be connected simultaneously to live DC power sources.These switches have been designed for harsh industrial environments,such as in maritime(DNV/LR/ABS/NK),rail wayside,highway,or mobile applications(EN50121-4/NEMA TS2/e-Mark),or hazardous locations(Class I Div.2,ATEX Zone2)that comply with FCC,UL,and CE standards.The EDS-208A switches are available with a standard operating temperature range from-10to60°C,or with a wide operating temperature range from-40to75°C.All models are subjected to a100%burn-in test to ensure that they fulfill the special needs of industrial automation control applications.In addition,the EDS-208A switches have DIP switches for enabling or disabling broadcast storm protection,providing another level of flexibility for industrial applications.SpecificationsEthernet Interface10/100BaseT(X)Ports(RJ45connector)EDS-208A/208A-T Models:8EDS-208A-M-SC/M-ST/S-SC Models:7EDS-208A-MM-SC/MM-ST/SS-SC Models:6All Models Support:Auto negotiation speedFull/Half duplex modeAuto MDI/MDI-X connection100BaseFX Ports(multi-mode SC connector)EDS-208A-M-SC Models:1EDS-208A-MM-SC Models:2100BaseFX Ports(multi-mode ST connector)EDS-208A-M-ST Models:1EDS-208A-MM-ST Models:2100BaseFX Ports(single-mode SC connector)EDS-208A-S-SC Models:1EDS-208A-SS-SC Models:2Standards IEEE802.3for10BaseTIEEE802.3u for100BaseT(X)and100BaseFXIEEE802.3x for flow controlOptical Fiber800Typical Distance4km5km40kmWavelengthTypical(nm)13001310TX Range(nm)1260to13601280to1340 RX Range(nm)1100to16001100to1600Optical PowerTX Range(dBm)-10to-200to-5 RX Range(dBm)-3to-32-3to-34 Link Budget(dB)1229 Dispersion Penalty(dB)31Note:When connecting a single-mode fiber transceiver,we recommend using anattenuator to prevent damage caused by excessive optical power.Note:Compute the“typical distance”of a specific fiber transceiver as follows:Linkbudget(dB)>dispersion penalty(dB)+total link loss(dB).Switch PropertiesMAC Table Size2KPacket Buffer Size768kbitsProcessing Type Store and ForwardPower ParametersConnection1removable4-contact terminal block(s)Input Current EDS-208A/208A-T,EDS-208A-M-SC/M-ST/S-SC Models:0.11A@24VDCEDS-208A-MM-SC/MM-ST/SS-SC Models:0.15A@24VDCInput Voltage12/24/48VDCRedundant dual inputsOperating Voltage9.6to60VDCOverload Current Protection SupportedReverse Polarity Protection SupportedDIP Switch ConfigurationEthernet Interface Broadcast storm protectionPhysical CharacteristicsHousing AluminumIP Rating IP30Dimensions50x114x70mm(1.96x4.49x2.76in)Weight275g(0.61lb)Installation DIN-rail mountingWall mounting(with optional kit) Environmental LimitsOperating Temperature Standard Models:-10to60°C(14to140°F)Wide Temp.Models:-40to75°C(-40to167°F) Storage Temperature(package included)-40to85°C(-40to185°F)Ambient Relative Humidity5to95%(non-condensing)Standards and CertificationsEMC EN55032/24EMI CISPR32,FCC Part15B Class AEMS IEC61000-4-2ESD:Contact:6kV;Air:8kVIEC61000-4-3RS:80MHz to1GHz:10V/mIEC61000-4-4EFT:Power:2kV;Signal:1kVIEC61000-4-5Surge:Power:2kV;Signal:2kVIEC61000-4-6CS:10VIEC61000-4-8PFMFHazardous Locations ATEXClass I Division2Maritime ABSLRNKDNVRailway EN50121-4Safety UL508Shock IEC60068-2-27Traffic Control NEMA TS2Vibration IEC60068-2-6Freefall IEC60068-2-31MTBFTime2,701,531hrsStandards Telcordia(Bellcore),GBWarrantyWarranty Period5yearsDetails See /warrantyPackage ContentsDevice1x EDS-208A Series switchDocumentation1x quick installation guide1x warranty cardDimensionsOrdering InformationModel Name 10/100BaseT(X)PortsRJ45Connector100BaseFX PortsMulti-Mode,SCConnector100BaseFX PortsMulti-Mode,STConnector100BaseFX PortsSingle-Mode,SCConnectorOperating Temp.EDS-208A8–––-10to60°C EDS-208A-T8–––-40to75°C EDS-208A-M-SC71––-10to60°C EDS-208A-M-SC-T71––-40to75°C EDS-208A-M-ST7–1–-10to60°C EDS-208A-M-ST-T7–1–-40to75°C EDS-208A-MM-SC62––-10to60°C EDS-208A-MM-SC-T62––-40to75°C EDS-208A-MM-ST6–2–-10to60°C EDS-208A-MM-ST-T6–2–-40to75°C EDS-208A-S-SC7––1-10to60°C EDS-208A-S-SC-T7––1-40to75°C EDS-208A-SS-SC6––2-10to60°C EDS-208A-SS-SC-T6––2-40to75°C Accessories(sold separately)Power SuppliesDR-120-24120W/2.5A DIN-rail24VDC power supply with universal88to132VAC or176to264VAC input byswitch,or248to370VDC input,-10to60°C operating temperatureDR-452445W/2A DIN-rail24VDC power supply with universal85to264VAC or120to370VDC input,-10to50°C operating temperatureDR-75-2475W/3.2A DIN-rail24VDC power supply with universal85to264VAC or120to370VDC input,-10to60°C operating temperatureMDR-40-24DIN-rail24VDC power supply with40W/1.7A,85to264VAC,or120to370VDC input,-20to70°Coperating temperatureMDR-60-24DIN-rail24VDC power supply with60W/2.5A,85to264VAC,or120to370VDC input,-20to70°Coperating temperatureWall-Mounting KitsWK-46-01Wall-mounting kit,2plates,8screws,46x66.8x2mmRack-Mounting KitsRK-4U19-inch rack-mounting kit©Moxa Inc.All rights reserved.Updated Sep19,2023.This document and any portion thereof may not be reproduced or used in any manner whatsoever without the express written permission of Moxa Inc.Product specifications subject to change without notice.Visit our website for the most up-to-date product information.。
MOXA EDS-508A 8口Managed交换机产品介绍说明书
EDS-508A Series8-port managed EthernetswitchesFeatures and Benefits•Turbo Ring and Turbo Chain (recovery time <20ms @250switches),andSTP/RSTP/MSTP for network redundancy•TACACS+,SNMPv3,IEEE 802.1X,HTTPS,and SSH to enhance networksecurity•Easy network management by web browser,CLI,Telnet/serial console,Windows utility,and ABC-01•Supports MXstudio for easy,visualized industrial network managementCertificationsIntroductionThe EDS-508A standalone 8-port managed Ethernet switches,with their advanced Turbo Ring and Turbo Chain technologies (recovery time <20ms),RSTP/STP,and MSTP,increase the reliability and availability of your industrial Ethernet network.Models with a wide operating temperature range of -40to 75°C are also available,and the switches support advanced management and security features,making the EDS-508A switches suitable for any harsh industrial environment.Additional Features and Benefits•Command line interface (CLI)for quickly configuring major managed functions•DHCP Option 82for IP address assignment with different policies •Supports EtherNet/IP and Modbus TCP protocols for device management and monitoring•Compatible with PROFINET protocol for transparent data transmission•Automatic warning by exception through email and relay output •IGMP snooping and GMRP for filtering multicast traffic•Port-based VLAN,IEEE 802.1Q VLAN,and GVRP to ease network planning•QoS (IEEE 802.1p/1Q and TOS/DiffServ)to increase determinism •Port Trunking for optimum bandwidth utilization•RMON for proactive and efficient network monitoring•SNMPv1/v2c/v3for different levels of network management•Bandwidth management to prevent unpredictable network status •Lock port function for blocking unauthorized access based on MAC addressSpecificationsInput/Output InterfaceAlarm Contact Channels 2,Relay output with current carrying capacity of 1A @24VDC Digital Input Channels 2Digital Inputs+13to +30V for state 1-30to +3V for state 0Max.input current:8mA ButtonsReset buttonEthernet Interface10/100BaseT(X)Ports (RJ45connector)EDS-508A Series:8EDS-508A-MM/SS Series:6All models support:Auto negotiation speed Full/Half duplex modeAuto MDI/MDI-X connection100BaseFX Ports (multi-mode SC connector)EDS-508A-MM-SC Series:2100BaseFX Ports(multi-mode ST connector)EDS-508A-MM-ST Series:2100BaseFX Ports(single-mode SC connector)EDS-508A-SS-SC Series:2EDS-508A-SS-SC-80Series:2100BaseFX Ports,Single-Mode SC Connector,80kmStandards IEEE802.3for10BaseTIEEE802.3u for100BaseT(X)and100BaseFXIEEE802.1X for authenticationIEEE802.1D-2004for Spanning Tree ProtocolIEEE802.1w for Rapid Spanning Tree ProtocolIEEE802.1s for Multiple Spanning Tree ProtocolIEEE802.1Q for VLAN TaggingIEEE802.1p for Class of ServiceIEEE802.3x for flow controlIEEE802.3ad for Port Trunk with LACPEthernet Software FeaturesFilter802.1Q VLAN,Port-based VLAN,IGMP v1/v2,GVRP,GMRPIndustrial Protocols EtherNet/IP,Modbus TCP,PROFINETManagement IPv4/IPv6,SNMPv1/v2c/v3,LLDP,Port Mirror,Back Pressure Flow Control,BOOTP,DDM,DHCP Option66/67/82,DHCP Server/Client,Fiber check,Flow control,RARP,RMON,SMTP,SNMP Inform,Syslog,Telnet,TFTPMIB MIB-II,Bridge MIB,Ethernet-like MIB,P-BRIDGE MIB,Q-BRIDGE MIB,RMON MIBGroups1,2,3,9,RSTP MIBRedundancy Protocols STP,MSTP,RSTP,LACP,Link Aggregation,Turbo Chain,Turbo Ring v1/v2Security HTTPS/SSL,TACACS+,Port Lock,RADIUS,SSHTime Management NTP Server/Client,SNTP,IEEE1588v2PTP(software-based)Switch PropertiesIGMP Groups256MAC Table Size8KMax.No.of VLANs64Packet Buffer Size1MbitsPriority Queues4VLAN ID Range VID1to4094LED InterfaceLED Indicators PWR1,PWR2,FAULT,10/100M(TP port),100M(fiber port),MSTR/HEAD,CPLR/TAIL Serial InterfaceConsole Port RS-232(TxD,RxD,GND),8-pin RJ45(115200,n,8,1)DIP Switch ConfigurationEthernet Interface Turbo Ring,Master,Coupler,ReservePower ParametersConnection2removable6-contact terminal block(s)Input Voltage12/24/48VDC,Redundant dual inputsOperating Voltage9.6to60VDCInput Current EDS-508A Series:0.22A@24VDCEDS-508A-MM/SS Series:0.30A@24VDCOverload Current Protection SupportedReverse Polarity Protection SupportedPhysical CharacteristicsHousing MetalIP Rating IP30Dimensions80.2x135x105mm(3.16x5.31x4.13in)Weight1040g(2.3lb)Installation DIN-rail mounting,Wall mounting(with optional kit) Environmental LimitsOperating Temperature Standard Models:-10to60°C(14to140°F)Wide Temp.Models:-40to75°C(-40to167°F)Storage Temperature(package included)-40to85°C(-40to185°F)Ambient Relative Humidity5to95%(non-condensing)Standards and CertificationsSafety EN60950-1,UL60950-1,CSA C22.2No.60950-1,UL508 Hazardous Locations ATEX,Class I Division2EMC EN55032/24EMI CISPR32,FCC Part15B Class AEMS IEC61000-4-2ESD:Contact:6kV;Air:8kVIEC61000-4-3RS:80MHz to1GHz:20V/mIEC61000-4-4EFT:Power:2kV;Signal:1kVIEC61000-4-5Surge:Power:2kV;Signal:2kVIEC61000-4-6CS:10VIEC61000-4-8PFMFShock IEC60068-2-27Vibration IEC60068-2-6Freefall IEC60068-2-31MTBFTime1,043,909hrsStandards Telcordia(Bellcore),GBWarrantyWarranty Period5yearsDetails See /warrantyPackage ContentsDevice1x EDS-508A Series switchCable1x DB9female to RJ4510-pinInstallation Kit4x cap,plastic,for RJ45port2x cap,plastic,for SC fiber port(-SC models)2x cap,plastic,for ST fiber port(-ST models)Documentation1x quick installation guide1x warranty card1x product certificates of quality inspection,Simplified Chinese1x product notice,Simplified ChineseDimensionsOrdering InformationModel Name 10/100BaseT(X)Ports,RJ45Connector100BaseFX PortsMulti-Mode,SCConnector100BaseFX PortsMulti-Mode,STConnector100BaseFX PortsSingle-Mode,SCConnector100BaseFX PortsSingle-Mode,SCConnector,80kmOperating Temp.EDS-508A8––––0to60°C EDS-508A-T8––––-40to75°C EDS-508A-MM-SC62–––0to60°C EDS-508A-MM-SC-T62–––-40to75°C EDS-508A-MM-ST6–2––0to60°C EDS-508A-MM-ST-T6–2––-40to75°C EDS-508A-SS-SC6––2–0to60°C EDS-508A-SS-SC-T6––2–-40to75°C EDS-508A-SS-SC-806–––20to60°C EDS-508A-SS-SC-80-T6–––2-40to75°C Accessories(sold separately)SoftwareMXview Industrial network management software designed for converged automation networksStorage KitsABC-01Configuration backup and restoration tool for managed Ethernet switches and AWK Series wirelessAPs/bridges/clients,0to60°C operating temperaturePower SuppliesDR-120-24120W/2.5A DIN-rail24VDC power supply with universal88to132VAC or176to264VAC input byswitch,or248to370VDC input,-10to60°C operating temperatureDR-452445W/2A DIN-rail24VDC power supply with universal85to264VAC or120to370VDC input,-10to50°C operating temperatureDR-75-2475W/3.2A DIN-rail24VDC power supply with universal85to264VAC or120to370VDC input,-10to60°C operating temperatureMDR-40-24DIN-rail24VDC power supply with40W/1.7A,85to264VAC,or120to370VDC input,-20to70°Coperating temperatureMDR-60-24DIN-rail24VDC power supply with60W/2.5A,85to264VAC,or120to370VDC input,-20to70°Coperating temperatureWall-Mounting KitsWK-46Wall-mounting kit,2plates,8screws,46.5x66.8x1mmRack-Mounting KitsRK-4U19-inch rack-mounting kit©Moxa Inc.All rights reserved.Updated Jan31,2019.This document and any portion thereof may not be reproduced or used in any manner whatsoever without the express written permission of Moxa Inc.Product specifications subject to change without notice.Visit our website for the most up-to-date product information.。
MOXA EDS-408A 系列8口工业级Managed Ethernet交换机产品介绍说明书
EDS-408A Series8-port entry-level managed EthernetswitchesFeatures and Benefits•Turbo Ring and Turbo Chain(recovery time<20ms@250switches),and RSTP/STP for network redundancy•IGMP Snooping,QoS,IEEE802.1Q VLAN,and port-based VLAN supported •Easy network management by web browser,CLI,Telnet/serial console, Windows utility,and ABC-01•PROFINET or EtherNet/IP enabled by default(PN or EIP models)•Supports MXstudio for easy,visualized industrial network managementCertificationsIntroductionThe EDS-408A Series is designed especially for industrial applications.The switches support a variety of useful management functions,such as Turbo Ring,Turbo Chain,ring coupling,IGMP snooping,IEEE802.1Q VLAN,port-based VLAN,QoS,RMON,bandwidth management,port mirroring,and warning by email or relay.The ready-to-use Turbo Ring can be set up easily using the web-based management interface,or with the DIP switches located on the top panel of the EDS-408A switches.Additional Features and Benefits•DHCP Option82for IP address assignment with different policies•Supports EtherNet/IP,Modbus TCP and PROFINET1protocols fordevice management and monitoring•EtherNet/IP EDS(Electronic Data Sheet)file,custom AOI(Add-OnInstructions)and FactoryTalk®View faceplate available•PROFINET GSDML file and SIMATIC STEP7device icons available1•Port mirroring for online debugging•Port-based VLAN,IEEE802.1Q VLAN,and GVRP to ease networkplanning•QoS(IEEE802.1p and TOS/DiffServ)to increase determinism•RMON for proactive and efficient network monitoring•SNMPv1/v2c/v3for different levels of network management security•Bandwidth management to prevent unpredictable network status SpecificationsEthernet Interface10/100BaseT(X)Ports(RJ45connector)EDS-408A/408A-T,EDS-408A-EIP/PN models:8EDS-408A-MM-SC/MM-ST/SS-SC models:6EDS-408A-3M-SC/3M-ST/3S-SC/3S-SC-48/1M2S-SC/2M1S-SC models:5All models support:Auto negotiation speedFull/Half duplex modeAuto MDI/MDI-X connection100BaseFX Ports(multi-mode SC connector)EDS-408A-MM-SC/2M1S-SC models:2EDS-408A-3M-SC models:3EDS-408A-1M2S-SC models:1100BaseFX Ports(multi-mode ST connector)EDS-408A-MM-ST models:2EDS-408A-3M-ST models:3100BaseFX Ports(single-mode SC connector)EDS-408A-SS-SC/1M2S-SC models:2EDS-408A-2M1S-SC models:1EDS-408A-3S-SC/3S-SC-48models:31.EDS-408A-PN Series onlyStandards IEEE802.3for10BaseTIEEE802.3u for100BaseT(X)and100BaseFXIEEE802.3x for flow controlIEEE802.1D-2004for Spanning Tree ProtocolIEEE802.1p for Class of ServiceIEEE802.1Q for VLAN TaggingIEEE802.1w for Rapid Spanning Tree ProtocolOptical Fiber800Typical Distance4km5km40kmWavelengthTypical(nm)13001310TX Range(nm)1260to13601280to1340 RX Range(nm)1100to16001100to1600Optical PowerTX Range(dBm)-10to-200to-5 RX Range(dBm)-3to-32-3to-34 Link Budget(dB)1229 Dispersion Penalty(dB)31Note:When connecting a single-mode fiber transceiver,we recommend using anattenuator to prevent damage caused by excessive optical power.Note:Compute the“typical distance”of a specific fiber transceiver as follows:Linkbudget(dB)>dispersion penalty(dB)+total link loss(dB).Ethernet Software FeaturesFilter802.1Q VLAN,GMRP,GVRP,IGMP v1/v2,Port-based VLANIndustrial Protocols EtherNet/IP,Modbus TCP,EDS-408A-PN models:PROFINET IO Device(Slave) Management Back Pressure Flow Control,BOOTP,DHCP Option66/67/82,DHCP Server/Client,Flowcontrol,IPv4/IPv6,LLDP,Port Mirror,RARP,RMON,SMTP,SNMP Inform,SNMPv1/v2c/v3,Syslog,Telnet,TFTPMIB Bridge MIB,Ethernet-like MIB,MIB-II,P-BRIDGE MIB,RMON MIB Groups1,2,3,9,RSTP MIBRedundancy Protocols RSTP,STP,Turbo Chain,Turbo Ring v1/v2Time Management NTP Server/Client,SNTPSwitch PropertiesIGMP Groups256MAC Table Size8KMax.No.of VLANs64Packet Buffer Size1MbitsPriority Queues4VLAN ID Range VID1to4094Serial InterfaceConsole Port RS-232(TxD,RxD,GND),10-pin RJ45(115200,n,8,1)DIP Switch ConfigurationEthernet Interface Turbo Ring,Master,Coupler,ReserveInput/Output InterfaceAlarm Contact Channels Relay output with current carrying capacity of1A@24VDCPower ParametersConnection1removable6-contact terminal block(s)Input Voltage All models:Redundant dual inputsEDS-408A/408A-T,EDS-408A-MM-SC/MM-ST/SS-SC/3M-SC/3M-ST/3S-SC/1M2S-SC/2M1S-SC/EIP/PN models:12/24/48VDCEDS-408A-3S-SC-48/408A-3S-SC-48-T models:±24/±48VDCOperating Voltage EDS-408A/408A-T,EDS-408A-MM-SC/MM-ST/SS-SC/3M-SC/3M-ST/3S-SC/1M2S-SC/2M1S-SC/EIP/PN models:9.6to60VDCEDS-408A-3S-SC-48models:±19to±60VDC2Input Current EDS-408A,EDS-408A-EIP/PN/MM-SC/MM-ST/SS-SC models:0.61@12VDC0.3@24VDC0.16@48VDCEDS-408A-3M-SC/3M-ST/3S-SC/1M2S-SC/2M1S-SC models:0.73@12VDC0.35@24VDC0.18@48VDCEDS-408A-3S-SC-48models:0.33A@24VDC0.17A@48VDCOverload Current Protection SupportedReverse Polarity Protection SupportedPhysical CharacteristicsHousing MetalIP Rating IP30Dimensions53.6x135x105mm(2.11x5.31x4.13in)Weight EDS-408A,EDS-408A-MM-SC/MM-ST/SS-SC/EIP/PN models:650g(1.44lb)EDS-408A-3M-SC/3M-ST/3S-SC/3S-SC-48/1M2S-SC/2M1S-SC models:890g(1.97lb) Installation DIN-rail mounting,Wall mounting(with optional kit)Environmental LimitsOperating Temperature Standard Models:-10to60°C(14to140°F)Wide Temp.Models:-40to75°C(-40to167°F)Storage Temperature(package included)-40to85°C(-40to185°F)Ambient Relative Humidity5to95%(non-condensing)Standards and CertificationsSafety All models:EN60950-1,UL508EDS-408A/408A-T,EDS-408A-MM-SC/MM-ST/SS-SC models,EDS-EIP/PN models:UL60950-1EMC EN55032/242.-60to-19VDC or19to60VDC.Do not mix power polarity systems.EMI CISPR32,FCC Part15B Class AEMS IEC61000-4-2ESD:Contact:6kV;Air:8kVIEC61000-4-3RS:80MHz to1GHz:10V/mIEC61000-4-4EFT:Power:2kV;Signal:2kVIEC61000-4-5Surge:Power:2kV;Signal:2kVIEC61000-4-6CS:10VIEC61000-4-8PFMFHazardous Locations EDS-408A,EDS-408A-MM-SC/MM-ST/SS-SC/EIP/PN models:ATEX,Class I Division2EDS-408A,EDS-408A-MM-SC/MM-ST/SS-SC models:IECExMaritime EDS-408A,EDS-408A-MM/SS-SC models:NKEDS-408A,EDS-408A-MM/SS-SC/EIP/PN models:DNVRailway EN50121-4Traffic Control NEMA TS2Freefall IEC60068-2-31Shock IEC60068-2-27Vibration IEC60068-2-6MTBFTime EDS-408A,EDS-408A-EIP/PN models:1,339,439hrsEDS-408A-MM-SC/MM-ST/SS-SC/3M-SC/3M-ST/3S-SC/1M2S-SC/2M1S-SC models:1,253,072hrsEDS-408A-3S-SC-48models:989,940hrsStandards Telcordia(Bellcore),GBWarrantyWarranty Period5yearsDetails See /warrantyPackage ContentsDevice1x EDS-408A Series switchCable1x RJ45-to-DB9console cableInstallation Kit4x cap,plastic,for RJ45portDocumentation1x product certificates of quality inspection,Simplified Chinese1x product notice,Simplified Chinese1x quick installation guide1x warranty cardDimensions Ordering InformationModel Name Layer Total No.ofPorts10/100BaseT(X)PortsRJ45Connector100BaseFXPortsMulti-Mode,SCConnector100BaseFXPortsMulti-Mode,STConnector100BaseFXPortsSingle-Mode,SCConnectorOperating Temp.EDS-408A288–––-10to60°CEDS-408A-T288–––-40to75°C EDS-408A-MM-ST286–2–-10to60°C EDS-408A-MM-ST-T286–2–-40to75°C EDS-408A-MM-SC2862––-10to60°C EDS-408A-MM-SC-T2862––-40to75°C EDS-408A-SS-SC286––2-10to60°C EDS-408A-SS-SC-T286––2-40to75°C EDS-408A-3M-ST285–3–-10to60°C EDS-408A-3M-ST-T285–3–-40to75°C EDS-408A-3M-SC2853––-10to60°C EDS-408A-3M-SC-T2853––-40to75°C EDS-408A-3S-SC285––3-10to60°C EDS-408A-3S-SC-T285––3-40to75°C EDS-408A-3S-SC-48285––3-10to60°C EDS-408A-3S-SC-48-T285––3-40to75°C EDS-408A-1M2S-SC2851–2-10to60°CEDS-408A-1M2S-SC-T2851–2-40to75°C EDS-408A-2M1S-SC2852–1-10to60°CEDS-408A-2M1S-SC-T2852–1-40to75°CEDS-408A-EIP288–––-10to60°C EDS-408A-EIP-T288–––-40to75°C EDS-408A-PN288–––-10to60°C EDS-408A-PN-T288–––-40to75°C Accessories(sold separately)Storage KitsABC-01Configuration backup and restoration tool for managed Ethernet switches and AWK Series wirelessAPs/bridges/clients,0to60°C operating temperaturePower SuppliesDR-120-24120W/2.5A DIN-rail24VDC power supply with universal88to132VAC or176to264VAC input byswitch,or248to370VDC input,-10to60°C operating temperatureDR-452445W/2A DIN-rail24VDC power supply with universal85to264VAC or120to370VDC input,-10to50°C operating temperatureDR-75-2475W/3.2A DIN-rail24VDC power supply with universal85to264VAC or120to370VDC input,-10to60°C operating temperatureMDR-40-24DIN-rail24VDC power supply with40W/1.7A,85to264VAC,or120to370VDC input,-20to70°Coperating temperatureMDR-60-24DIN-rail24VDC power supply with60W/2.5A,85to264VAC,or120to370VDC input,-20to70°Coperating temperatureSoftwareMXview-50Industrial network management software with a license for50nodes(by IP address)MXview-100Industrial network management software with a license for100nodes(by IP address)MXview-250Industrial network management software with a license for250nodes(by IP address)MXview-500Industrial network management software with a license for500nodes(by IP address)MXview-1000Industrial network management software with a license for1000nodes(by IP address)MXview-2000Industrial network management software with a license for2000nodes(by IP address)MXview Upgrade-50License expansion of MXview industrial network management software by50nodes(by IP address) Wall-Mounting KitsWK-46-01Wall-mounting kit,2plates,8screws,46x66.8x2mmRack-Mounting KitsRK-4U19-inch rack-mounting kit©Moxa Inc.All rights reserved.Updated May12,2022.This document and any portion thereof may not be reproduced or used in any manner whatsoever without the express written permission of Moxa Inc.Product specifications subject to change without notice.Visit our website for the most up-to-date product information.。
MOXA交换机环网及Vlan配置
MOXA交换机配置：1、如何进入配置界面：Web、串口Console 、Telnet (1)2、交换机IP地址配置 (3)3、端口镜像配置 (4)4、环网配置 (5)5、Vlan配置 (6)6、三层配置 (7)7、交换机日志导出配置 (9)1、如何进入配置界面：Web、串口Console 、TelnetWeb配置直接通过浏览器输入交换机IP地址（需要主机与交换机IP在同一网段中）Telnet通过command串口，配置主机IP与交换机在同一网段，输入“Telnet 192.168.127.253(默认IP)”，如下图：串口Console配置通过串口参数：（115200，None，8，1，VT100）打开串口配置个选项对应功能2、交换机IP地址配置在“Basic setting”选项下，选中“Network”选项，如下图交换机名称配置：在“Basic setting”选项下，选中“Systerm”选项，如下图3、端口镜像配置点击“Disagnosi”选项，点击“Mirror”选项，如下图在“Monitored Port”选择被检测端口在“Mirror”选择用于抓包的端口4、环网配置“communication Redundancy”选项，在右边的下拉菜单中选择环网协议turboring或turboring v2，之后进入配置界面如下图，现已Turboring V2介绍。
备注：Turboring与Turboring V2这两个协议之间不兼容，请确定所有交换机的环网协议要相同一致，要么全是Turboring，要么全是Turboring V2环网中的交换机其中一台选择为master，把“set as master”选中即可，默认的环网端口都为交换机的最后两个端口，比如上去408交换机，环网端口为7和8，之后点Activate应用即可。
按照这个方法，把所有的交换机的环网设置都设置为Turboring V2，即可组环使用。
MOXA交换机设置指导
Moxa交换机特点
01
高可靠性
Moxa交换机采用工业级设计， 具有防震、防尘、防潮等特点， 能够在恶劣的环境下稳定运行。
实时性
02
03
易管理性
Moxa交换机支持实时传输技术， 能够满足工业自动化等领域的实 时性要求。
解决方案
检查交换机的IP地址配置是否正确，确认连接线缆是否正常，核对登录凭证（用户名和 密码）是否正确。如果问题依然存在，可能需要重置交换机或联系技术支持。
VLAN配置错误
总结词
交换机上配置的VLAN不正确，导致无法实现正确的网络隔 离。
详细描述
可能是在配置VLAN时，将端口错误地划分到了不同的 VLAN，或者VLAN的名称和IP地址配置不正确。
Moxa交换机提供Web界面和命 令行接口，方便用户进行配置和 管理。
Moxa交换机应用场景
01
02
03
04
工业自动化
Moxa交换机可用于工厂自动 化生产线、智能制造等领域， 实现设备间的数据传输和控制
。
轨道交通
Moxa交换机可用于地铁、轻 轨等轨道交通系统，实现车辆
控制、信号传输等功能。
智能交通
VS
配置管理
Moxa交换机支持通过Web界面或命令行 进行配置管理。用户可以根据实际需求， 对交换机的各项参数进行设置，如VLAN 划分、端口配置、IP地址分配等。
固件升级与备份
固件升级
随着技术的不断更新，Moxa交换机也需要不断升级固件以支持新的功能和修复已知的 漏洞。用户可以通过Moxa官方网站下载最新的固件版本，并按照说明进行升级操作。
环网交换机配置
2.1 设置交换机双击计算机桌面上的“edscfgui”图标，进入软件设置交换机界面。
单击菜单“List Server”，在点击“Broadcast Search”，如图2。
图2计算机开始搜索网络上的交换机，搜索完成后弹出如图3的窗口，双击IP Adress为“192.168.127.253”的交换机，弹出如图4的窗口，单击IP Adress前的复选框，将IP Adress改成“192.168.127.20”。
点击“确定”，弹出如图5的窗口，点击“是”，保存并重新搜索网络交换机。
图3图4交换机的MAC码图5双击桌面上的“Internet Explorer”图标，在“地址”栏输入“192.168.127.20”，进入网络交换机。
如图6。
点击“Communication Redundancy”进入网络交换机的冗余模式选择，出厂配置选择“Turbo Ring With ED6008 Series”模式。
然后点击“Activate”。
点击“Advanced Setting”前的“+”号，再点击“Password”，弹出图7。
在“New Password”和“Retype Password”后的方框在填入“cari”（出厂配置），然后点击“Activate”，出现提示语“Password Setup OK！”。
图6图72.2 以太网/RS485转换单元配置（如不带转换单元则不用进行该步骤）CJJ02矿用环网接入器可接入RS485转以太网模块，每个模块的配置除IP Adress和虚拟的COM口不同，其他配置完全相同。
现以第一个模块的配置方法为例阐述其配置方法。
把转换模块连接至环网交换机后，点击计算机桌面上的“Network Enable Administrator”图标，进入以太网/RS485转换单元的设置，如图8。
点击菜单“Configuration”，然后点击“Broadcast Search”搜索以太网/RS485转换单元。
怎样设置MOXA交换机环网协议
怎样设置MOXA交换机环网协议
• 1. 应用产品
Product Line Model Name
EDS-518E EDS-518E
EDS-408A EDS-408A
• 2. 系统架构
• 3. 交换机设置
3.1 准备
如果交换机是新产品没有做过配置的话，那么它的IP地址就是它的默认IP:192.168.127.253，这时要将PC的有线网卡设置成跟它同一网段，即192.168.128.xxx
• 3.2 配置交换机
3.2.1 交换机
将所有交换机级联并进行设置，请先不要将交换机连成环网。
连接电脑的有线网卡到交换机，并关闭电脑的无线网卡，运行edscfgui软件，并点击search.
• 3.2.2 登录交换机
点击edscfgui软件中的web登入
•或者直接在web浏览器中输入交换机的IP地址，用户名：admin，默认密码：空或者moxa
EDS-400系列默认密码为空
•EDS-500系列默认密码为moxa
• 3.3.3 设置Turbo Ring
•开启第一个环，并设置启用Turbo Ring 的两个端口，点击Activate启用•EDS-500E系列点击Redundancy Protocol，选择Turbo Ring v2模式
•开启第一个环，并设置启用Turbo Ring的两个端口，点击Apply启用
• 4. Turbo Ring 测试
将所有交换机按照所设置的端口连接成环网，电脑连接任一交换机的任一端口，打开cmd，ping其他交换机，能够ping通，则说明环网设置成功。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
打开MOXA交换机光盘中自带的 edscfgui.exe配置工具 (EDS-408A/utility/edscfgui.exe 目录)
MOXA交换机环网配置步骤2
点击List Server -> Broadcast Search，软件自动开始搜索当前网 络内联网的交换机
上传
EDS-408A系列最新firmware版本支持Turbo Ring V2，相对于V1版 本，它的环网自愈时间由300ms升级为20ms。如选择V2版本，则支 持ring1和ring2两个环，请将环网内所有交换机都设置在ring1中。
MOXA交换机环网配置步骤4
请注意 Enable Ring Coupling环间耦合功能不启用，所以在前面 方框中不要勾选。 修改内容后记得点击Activate，激活页面上的设置内容。 (其他菜单页面修改后同样需要点击Activate才能激活)
MOXA交换机环网配置步骤4
打开左边的communication redundancy菜单项，右边画面出现网络协 议设置画面。在redundancy Protocol处选择Turbo Ring V1， Redundant ports分别选择port 7和port 8。
MOXA交换机环网配置步骤4
MOXA交换机环网配置步骤2
MOXA交换机环网配置步骤2
选中当前交换机，点击右键菜单中的Modify IP Address一项， 弹出交换机IP修改对话框。
MOXA交换机环网配置步骤2
在IP Address一项前面打勾，并将交换机IP修改成需要的值。 确定后弹出警告对话框，选择yes即可。 依次将环网内的所有交换机IP环网配置步骤3
修改本地电脑的IP地址，使其与交换机的当前IP在同一网段下 如192.168.0.32。这时才能通过IE浏览器访问交换机。
MOXA交换机环网配置步骤4
pw4 net
打开系统自带的IE浏览器，在地址栏输入交换机的当前IP地址 交换机初始用户名admin，密码为空，直接点击Login进入
1. 第一次使用以上步骤，建议到每台交换机旁进行本地配置。
2. 配置前，先断开交换机的外部联网，使用一根普通网线连接交换机和PC的 RJ45口即可。
3. 环网内的交换机都配置好环网协议后，才能将光纤网连接成环形，之前只 能连接成总线型，不能形成网络回环。
4. 对于EDS-408A-MM-SC，其中2个光口用作环网连接，请注意在turbo ring配 置页面中查看端口号是否对应正确。