锂离子电池规格书Word版
锂离子电池产品规格书.doc
DATE:2012.09.06
Li-ion Battery
Specification锂离子电池产品规格书
MODEL/型号:C11450-2S
（4.8V/500mAH）
VER:1.（适用范围）
ThisspecificationisappliedtothereferencebatteryinthisSpecificationandmanufacturedby
锂电池应当在室温下存放，应充到30%至50%的电量。如长时间储存，建议每半年充一次电以防止电池
过放电。
VER:1.0
DATE:2012.09.06
10.Initial Dimension:（初始尺寸）
不要焚毁电池，否则会致电池爆炸，这个很危险，必须禁止。
7.3 Battery cells replacement（更换电池）
Thebattery replacementshallbedoneonly by eithercellssupplierordevicesupplierand neverbedoneby theuser.
Thedisassemblingmaygenerateinternalshortcircuitinthecell,whichmaycausegassing,firing,explosion,or otherproblems.
2)Electrolyte is harmful
LIPbatteryshouldnothaveliquidfromelectrolyteflowing,butincasetheelectrolytecomeintocontactwiththe skin,oreyes,physiciansshallflushthe electrolyteimmediatelywithfreshwaterandmedicaladviceisto besought.
4812动力型锂离子产品规格书
放电
-20℃～70℃
2.1.9储存温度
1个月以内
-20℃～55℃
3个月以内
-20℃～45℃
6个月以内
-5℃～25℃
2.1.10 内阻
≤220mΩ
标准充电后24h内测得的AC 1KHz 交流阻抗值
2.2 尺寸及外观
2.2.1 尺寸：依据电池外壳（长*宽*高mm）
2.2.2 重量：约4Kg（含外壳）
1.2产品描述
1.2.1 名称：三元锂电池组
1.2.2型号：XKD4812
1.2.3 组成：磷酸铁锂电池和订制保护系统。
2产品规格
2.1 额定参数
项 目
要求参数
备 注
2.1.1额定容量
典型值
12Ah
电池按标准充电后，按标准放电所得的容量
最小值
11.8Ah
电池标准充电后按标准放电所得的最低容量
2.2.2标称电压
控制电路中的保护电路具有过充、过放及过流保护功能，主要技术参数如下：
项目
参数
备注
4.1.2.1 过充保护
充电时，如果单节电芯电压超过4.25V±0.01V，控制电路切断电路停止充电(可以放电)
通过放电可以解除保护
4.1.2.2 过放保护
放电时，如果单节电芯电压低于2.5V±0.10V，控制电路切断电路停止放电(可以充电)
48V
标准充电后标准放电过程中的平均电压
2.1.3放电终止电压
39V
当电池电压低于20V时请停止放电
2.1.4 充电方式
CC/CV
2.1.5充电电压
MAX.58.4V
2.1.6充电电流
≤0.5C（6.0A）
锂离子聚合物电池规格书说明书
页码：1/15602030PL300mAhSpecification of Li-ion Rechargeable Battery锂离子电池规格书Model：602030PL300mAh/3.7VCustomer Confirmation Customer Name: Customer No.: Comment:Customer Approval:Prepared by Checked by Approved by 肖志军602030PL300mAh页码：2/15兴永恒（深圳）电子有限公司深圳宝安区沙井后亭E-mail：****************Website：TEL：86-0755-********FAX：86-0755-********AMENDMENT RECORDSREVISION DATE ORIGINATOR REASON FOR REVISION A001 2016-6-20602030PL300mAh页码：3/15Content目录1. Scope范围 (4)2. Reference Standard 参考标准 (4)3. Picture of battery电池图 (4)3.1 Picture of single cell 单体电芯图 (4)3.2 Picture of assembled battery 组合电池图 (6)4. Basic of performance 基本性能 (7)4.1 Single cell parameters 单体电芯参数 (7)4.2 Assembled cell parameters包装后电芯组参数 (8)5. Electrical Characteristics电性能 (8)5.1 Normal Test Conditions标准测试条件 (8)5.2 Electrochemical Characteristics电化学性能 (8)5.3 Environment Characteristics环境适应性能 (9)5.4 Safety Characteristics 安全性能 (10)6. PCM Specification PCM 规格 (11)6.1 Electrical Characteristics电性能 (11)6.2 Circuit Diagram 电路图 (11)6.3 Circuit topology Drawing and PIN Explanation电路布线图和焊盘说明 (12)6.4 PCM BOM 保护板物料清单 (12)7. Storage and Shipment Requirement存储及运输要求 (13)8. Warning and Cautions 警告及注意事项 (13)9. Note 声明 (15)页码：4/15602030PL300mAh1. Scope范围This specification describes the performance, testing method, warning and caution of the lithium-ion rechargeable battery.The specification applies to polymer battery supplied by Shenzhen biyate energy co., ltd本标准描述了锂离子电池的性能、测试方法及注意事项。
eeMB BATTERY LIR18650 3000mAh 锂离子电池 产品规格书说明书
ModelChapter Content0Catalog………………………………………………………………………………………………….1Scope…………………………………………………………………………………………………...2Battery Basic Characteristics…………………………………………………………………………...3Battery Shape4Appearance…………………………………………………………………………………………...5Performance6Warranty……………………………………………………………………………………………....7Matters Needing1.Scope适用范围This product specificationcustomer by EEMB本产品规格书适用于2.Battery CellNo.2.12.2Capacity容量2.3Nominal2.42.5Internal3.Battery Cell 产品外形及尺寸（单位：MW L+T-L 2L 1NItem 项目Diameter Height25℃±2℃，0.3C2.75V，搁置5.2Electrical CharacteristicsITEM测试项目Discharge rate capacity倍率放电性能Cycle life循环寿命5.3AcclimatizationITEM测试项目Constant Temperature andHigh Humidity恒定湿热性能Drop test自由跌落Heating Test热冲击Overcharge Test 过充电●Strictly prohibits严禁把电池投入液体中，如水、汽油、饮料等，也不要把电池弄湿。
●Strictly prohibitsAlso do not禁止在火源附近或温度超过●Strictly prohibitsHairpins,coins,禁止把电池同项链、发夹、硬币或螺钉等金属品一起放在兜中或包中，也不要把电池同上述物品一起储存或运输。
电池电芯规格书模板
锂离子二次电池型号: 454060AP 1000mAh销售部地址：电话：（86）0755-传真：（86）0755-工厂地址：电话:（86）传真:（86）网址：目录●封面 (1)●目录 (2)●适用范围 (3)●引用标准 (3)●产品类型 (3)●产品规格 (3)●外观 (3)●性能 (3)●常规性能 (4)●环境适应性能 (5)●安全性能 (6)●技术和安全要求 (6)●包装、储存及运输 (7)●保质期限 (7)●电池使用时警告及注意事项 (8)●附：产品外形图 (9)1、适用范围：本产品规格适用于能源实业有限公司生产的二次锂离子电池主要性能指标的描述，此此份说明书仅适用于单体电池，用户请务必严格按说明书中的测试或使用方法进行使用，如有不明的事项，请与供应方协商解决。
2、引用标准：GB/T18287-20003、产品类型、型号和外形尺寸3.1 产品类型：二次锂离子电池3.2 产品型号：3.3 电芯外观尺寸（Max）: 厚×宽×长（mm)4、产品规格：5表面没有如脏污、严重擦伤、漏液、凹点和变形等缺陷。
6、性能6.1、标准测试条件无其他指定时，按 GB/T18287-2000 标准测试条件。
、65±20％RH（湿度）下进行；如果测试结果与要求条件无关，本规格书中所有的测试均在 23±2℃（温度）则也可以在 15～30℃(温度)、25～85％RH（湿度）下进行。
(潮湿中进行测试会影响测试结果)6.2、测试的手段和仪器6.2.1、测量尺寸的工具用 0.01mm 或更精确的工具来测量尺寸,其量程为 0-200mm.6.2.2、电压表和电流表电压表的精确度为±5mv,其量程为 0-20V;电流表的精确度为当前电流±0.3%.6.2.3、测量内阻国产的内阻仪使用一个(1KHz)的正弦交变电流来规范。
6.3、额定的充电的条件在23±2℃下以恒流 0.5C5A 充电 2.5 小时,最大上限电压为 4.2V.6.4、额定放电条件在23±2℃下以 0.5C 恒流放电至 3.0V 截止.7、常规性能：标准充电定义：在环境温度 23±2℃条件下，对电池以 0.2C5A 恒流充电至 4.2V，然后 4.2V 恒压充电至充电电流小于等于 0.05C5A。
电池规格书模板Word版
Specification Approval Sheet 产品规格承认书Customer 客户名称：域拓Model产品型号：4LType 产品类型：Li-ion battery Specification产品规格：3.7V/1400mAHAMENDMENT RECORDSCatalogue 目录1 .Battery type and scope电池型号和适用范围 (4)1 . 1: model产品型号： (4)1 . 2: scope适用范围：客户定义 (4)2 . Basic character and compose of battery电池的基本特性及组成 (4)2 . 1: fundamental performance parameter of battery电池基本性能参数： (4)2 . 2: Main components and parts主要零部件 (6)2 . 3: Regular performance and unfailing performance产品常规性能和可靠性能 (6)2 . 4: Contour Dimension of the Battery电池外形尺寸 (11)3 . Specifications of Parts零部件规格 (112)3 . 1: fender保护板 (122)3 . 2: general electric and protection characters一般电气与保护特征 (122)3 . 2: electric schematic diagram of battery电池电路原理图： (133)3 . 3 : PCB layout 电路布局图………………………………………………………………….错误!未定义书签。
34 . Specifications of the Cells电芯规格 (144)Announcements注意事项 (155)Danger 危险 (155)Warnings 警告 (166)Announcements 注意事项 (167)1 .Battery type and scope电池型号和适用范围This Specification Approval Sheet is for rechargeable Li-polymer battery provided by Shirui Battery Co., LTD.This product is according with the national standard of PRC. ‘GB/T18287-2000’. ‘General specification of lithium-ion battery for cellular phone’.本《规格书》为时瑞电池有限公司提供的可充电式锂离子电池规格。
锂离子电池规格书Word版
锂离子电池规格书型号：BL-5c标称: 1000mAh修订履历1、目的对深圳市好远通电子有限公司出品的可充锂离子电池的产品规格、测试方法进行规范，避免因测试条件、方法的不同引起误差。
2、产品类别和产品型号2.1 类别：锂离子可充电池2.2 产品型号高务电池BL-5C/1000mAh3、产品基本特性4、特性4.1电性能4.2 安全性能4.3 环境适应性温度：25±2℃，相对湿度：45±20%（除非另外要求）6、产品责任书消费者必须严格遵守深圳市好远通电子有限公司规格书和文件后面的注示使用电池，由于误用会引起电池过热，发生火灾或爆炸，对于没有按照规格书进行操作所造成的任何意外事故，深圳市慧通天下科技股份有限公司不负任何责任。
7、充电前注意事项如果规格书、原材料、生产过程或生产控制系统发生改变，改变的信息将会随质量和可靠性数据以书面形式通知消费者。
8、电池包装说明在电池的包装上应有如下说明！危险*充电时请使用指定的充电器并按照说明书的要求进行充电。
*仅在指定的设备上使用电池。
*不要把电池加热或投进火中。
*不要在火源附近或温度超过60℃的轿车中使用或遗留电池，也不要在这些环境中进行充电。
*不要把电池投入水中，也不要弄湿。
*不要把电池同项链、发夹、硬币或镙钉等金属品一起放在兜里或包中，也不要把电池同上述物品一起储存。
*不要使用金属导体短路电池的正负极。
*在装入设备时注意电池的正负极不要反装。
*不要使用锐利的物品刺穿电池。
*不要对电池进行分解。
*不要直接对电池进行焊接。
*不要使用带有严重伤痕或变形的电池。
*在使用之前请详细阅读操作说明书，不适当的操作可能引起电池变热、着火、爆炸、毁坏或电池容量的衰减。
！警告*不要把电池放在加热器皿、洗衣机或高压容器中。
*不要把电池同干电池或其它原电池一起使用，也不要同不同包装、不同型号或不同品牌的电池一起使用。
*如果在规定的充电时间内充电没有结束，停止充电。
锂离子电池规格书【完整版】
锂离子电池规格书【完整版】(文档可以直接使用，也可根据实际需要修订后使用,可编辑放心下载）★★★★★锂离子电池规格书SpecificationForLithium Ion Rechargeable Battery电池型号〔Type〕：383450AH标称容量〔Rated Capacity〕：700mAh部门〔Department〕：铝壳制造部生效日期〔Effective Date〕：2007-3-121.范围SCOPE AND APPLICATION本标准规定了锂离子电池的定义、技术要求、测试方法及考前须知。
本标准适用于深圳市山伊克斯技术生产的锂离子电池。
This specification describes the definition, technical requirement, testing method, warning and caution of the lithium ion rechargeable battery. The specification only applies to battery supplied by Shenzhen 3EX TECH. Co., Ltd.2. 定义 DEFINITION2.1 额定容量：指在20±5℃，65±5%RH 环境下，以5小时率放电至终止电压时的容量，单位毫安时(mAh)。
Rated Capacity: Under 20±5℃，65±5%RH, it means the capacity value of being discharged by 5hrs ratio to End Voltage.2.2 终止电压：放电终止时的规定电压为2.75V 。
End voltage: The end voltage of discharge is 2.75V ，which is defined specially.2.3 0.2倍率充电：指在20±5℃，65±5%RH 环境下，以140mA 电流恒流充电至单体电池电压4.2V 后，转为恒压4.2V 充电，至充电电流小于10±5mA ，停止充电。
2000mAh锂电池电池技术规格书
技术规格书型号：2000mAh编制：审核：批准：目录 Contents1. 范围 (3)2. 产品描述与型号 (3)3. 定义 (3)4. 产品规格 (3)5. 外形尺寸 (4)6. 外观 (4)7. 性能规格 (5)7.1 标准测试条件 (5)7.2 电性能 (5)7.3 环境适应性能 (6)7.4 安全性能 (6)7.5 机械性能 (6)8. 包装 (7)9. 运输 (7)8. 长期存储 (7)11. 保质期 (7)12. 产品责任 (7)电池组基本信息1.适用范围本产品规格书描述的是可充电锂离子电芯，包括产品规格信息、各种性能测试条件、产品责任及注意事项。
2.产品描述与型号2.1 产品描述: 电芯(可充电锂离子电池)2.2 型号 Model: 2000mAh3.定义3.1 标准模式充电标准模式充电的定义:在25±2℃下, 将电芯以0.5C电流恒流充电到4.2V, 然后转为在4.2V下恒压充电至截至电流0.01C。
3.2 标准模式放电标准模式放电的定义: 在25±2℃下, 将满电态电芯以0.2C电流恒流放电到3.0V。
4.产品规格工作温度和湿度范围充电 0 ~ 50℃60±25％R.H. 低温充电效率会下降，会影响电池使用寿命放电 -30 ~ 50℃60±25％R.H.电芯重量≤44.0±1.0g电芯尺寸高度≤65.50mm ；直径≤18.45 mm长时间存储温度-20~25℃60±25％R.H.不可超过半年，达到半年须充电一次带保护板电池3个月充电一次5.外形尺寸见附图图1. 外形尺寸6.主要零部件列表带帽PTC参数表7. 标准测试条件无其它指定时，按GB/18287-2013标准测试条件。
本规格书中所有的测试均在25±5℃（温度）≤75％RH（湿度）下进行；6.外观应没有如深度划痕、裂缝、生锈、斑点或漏液等影响电芯商业价值的外观瑕疵。
聚合物锂离子电池规格说明书
67XaG'_B 0.01 mm J 3.2.2 Voltmeter"O #
3.5 Initial Performance Test"9:A=# Table 2"K 2#
3.1 Standard Test Conditions"Y8=>?#
Test should be conducted with new batteries within one week after shipment from our factory and the cells shall not be cycled more than five times before the test. Unless otherwise specified, test and measurement shall be done under temperature of 20+5* and relative humidity of 45~85%. If it is
,-" 0.2C5A #[$ 8.4VE%[,,&'(_ )K 8.4V #`[$,(_ 0.02 C5AE [, !"# 6 _ JT 0*-45*[,,-* +,-.J 3.3.2 Standard Discharge"Y8],#
0.2C5A =100mA Cells shall be discharged at a constant current of 0.2 C5A to 6.0 volts @ 20º 5C ,-K 0.2 C5A #],$ 6.0V @ 20º 5C
锂离子电池产品规格书说明书
History of specification规格书修订记录Date Contents Remarks 2018-05-12First issue A0Content/目录1.Scope/适用范围Page42.Cell Specification/电芯规格说明Page4/53.Battery/Cell performance test Criteria/电池性能标准Page6 3.1Appearance inspection by visual/外观目测Page6 3.2Environmental test condition/外界环境条件Page6 3.3Electrical characteristics/电气特性Page6 3.4Mechanical characteristics/机械特性Page73.5Safety performance/安全性能Page7/84.Cell initial Dimensions/电芯初始尺寸Page84.2Picture of assembled battery组合电池图5.Protection Circuit保护电路5.1PCM parameter PCM参数6.Circuit topology Drawing and PIN Explanation电路布线图和焊盘说明6.1PCM BOM保护板物料清单6.2Assembled cell parameters包装后电芯组参数附录Page9 Page9 Page9 Page10 Page10 Page101.Scope/适用范围2.Cell Specification/电芯产品规格No.Item项目Specification性能1Rated Capacity额定容量3000mAh,0.2C discharging2Minimum Capacity最小容量3000mAh,0.2C discharging3Normal Voltage标称电压3.70V4O.C.V出厂电压 3.80-4.2V5Charge Ending Voltage充电截止电压4.20±0.03V6Discharge Ending Voltage放电截止电压3.0V7Standard charging method标准充电方式0.5C constant current charge to 4.2V,then constantvoltage4.2V charge till charged current declines to≤0.01C,0℃～45℃8Charge current充电电流Standard charge:0.5CRapid charge:1.0C9charging Time充电时间Standard charge:5.5～6.5hRapid charge:1.5～2.5h10Max.Charging Current最大充电电流1.0C(5℃～+45℃)11Standard dischargingCurrent标准放电电流0.5C constant current discharge to3.0V.10℃～+60℃12Max.Discharging Current最大放电电流1.0C(10℃～+60℃)13Operating environment工作环境Charging:0℃-45℃,65%±25%RHDischarging:10℃-60℃,65%±25%RH14Cell Impedance单电芯内阻＜45mohm，(4.2V AC1KHz measured)15Dimension of Single Cell单电芯尺寸Thickness Max8.0mmWidth Max56.5mmHeight Max60.5mm3.Picture of single cell单体电芯图Items Description Dimension and SpecT电芯厚度Max:8.0mmW电芯宽度Max:56.5mmH电芯长度Max:60.5mmC Tab间距18±2.0mmB Tab宽度 4.0±0.1mmD顶封宽度 4.0±0.5mmA极耳胶外露Max:2.0mmE极耳长度8.0±1.5mmFig.(1)The Dimension of Single Cell图(1)单体电池尺寸图4.Picture of assembled battery组合电池图Fig.(2)The Dimension of Assembled Battery图(2)组合电池外形尺寸图厚度T 宽度W 长度L 线径Ø线型插头型号Max:8.1Max:57.0Max:63.00.9UL1007/24#XH2.54-2P备注：UNIT 单位：MM5.产品规格及电气参数Product Specification and Electrical Parameters序号Item项目Specification性能1Assembled Mode组合方式1P2Normal Capacity标称容量≥3000mAh,0.2C discharging3Normal Voltage标称电压3.7V4Impedance成品内阻＜103mohm，(100%charge AC1KHz measured)5Assembly Dimension装配尺寸Thickness Max8.1mmWidth Max57.0mmHeight Max63.0mm4.Battery/Cell performance test Criteria/电池性能标准4.1Appearance inspection by visual/外观目测There shall be no such defect as rust,leakage,which may adversely affect commercial value of battery.电池外观应没有锈渍、污渍、漏液等影响商业价值的缺陷存在。
电池规格书模板
Specification Approval Sheet 产品规格承认书Customer 客户名称：域拓Model产品型号：4LType 产品类型：Li-ion battery Specification产品规格：3.7V/1400mAHAMENDMENT RECORDSCatalogue 目录1 .Battery type and scope电池型号和适用范围 (3)1 . 1: model产品型号： (4)1 . 2: scope适用范围：客户定义 (4)2 . Basic character and compose of battery电池的基本特性及组成 (4)2 . 1: fundamental performance parameter of battery电池基本性能参数： (4)2 . 2: Main components and parts主要零部件 (6)2 . 3: Regular performance and unfailing performance产品常规性能和可靠性能 (6)2 . 4: Contour Dimension of the Battery电池外形尺寸 (11)3 . Specifications of Parts零部件规格 (102)3 . 1: fender保护板 (102)3 . 2: general electric and protection characters一般电气与保护特征 (102)3 . 2: electric schematic diagram of battery电池电路原理图： (113)3 . 3 : PCB layout 电路布局图………………………………………………………………….错误!未定义书签。
34 . Specifications of the Cells电芯规格 (124)Announcements注意事项 (135)Danger 危险 (135)Warnings 警告 (146)Announcements 注意事项 (157)1 .Battery type and scope电池型号和适用范围This Specification Approval Sheet is for rechargeable Li-polymer battery provided by Shirui Battery Co., LTD.This product is according with the national standard of PRC. ‘GB/T18287-2000’. ‘General specification of lithium-ion battery for cellular phone’.本《规格书》为时瑞电池有限公司提供的可充电式锂离子电池规格。
锂电池组规格书范本
深圳市XXXXXX股份有限公司Li BATTERY SPECIFICATION锂离子电池规格书SHENZHEN MOTTCELL NEW ENERGY TECHNOLOGY CO.,LTDTel：+86-755-XXXXXXXFax：+86-755-XXXXXXX．S cope（使用范围）13.Product Specification（产品技术规格）4．Performance And Test Conditions（电池性能及测试条件）●Standard Test Conditions（标准测试条件）test and measurement shall be done under temperature of 25±5℃ and relative humidity of 45~48%. 测试会在温度25±5℃，相对湿度在45-85%的条件下进行。
●Measuring Instrument or Apparatus（测量器具及设备）①Dimension Measuring Instrument（尺寸测量器具）The dimension measurement shall be implemented by instruments with equal or more precision scale of 0.1mm.尺寸测量器具的精度等级应不小于0.1mm。
②Voltmeter（伏特计）Standard class specified in the national standard or more sensitive class having inner impedance more than 10kΩ/V.按照国家标准指定规格等级或采用灵敏度更高的，测量电压时内阻不应小于10kΩ/V。
③Ammeter（安培计）Standard class specified in the national standard or more sensitive class. Total external resistance includi ng ammeter and wire is less than 0.01Ω.按照国家标准指定规格等级或采用灵敏度更高的，包括电流表及电线在内的总外阻应小于0.01Ω。
IMP225069S 锂离子电池产品规格书说明书
锂离子电池产品规格书电池型号:IMP225069S编制：日期：审核：日期：确认：日期：顾客产品型号：___________________客户确认：___________________日期：__________供货商：武汉力兴（火炬）电源有限公司地址：武汉市东湖新技术开发区大学园路电话：86-27-87920872/87920873/87920946传真：86-27-87920945武汉力兴（火炬）电源有限公司编号：版本号：A/0IMP225069S1.目的1.1对于武汉力兴（火炬）电源有限公司出品的锂离子电池的产品规格，测试方法进行规范，避免因测试条件，方法的不同引起误差。
1.2指导客户正确使用我公司产品。
2.产品类别和产品型号2.1类别锂离子可充电池2.2型号IMP225069S3．产品基本特性4．外形示意图及尺寸4.1外形示意图如图所示序号项目特性备注1额定容量5000mAh 充电：0.2C /4.2V，恒压至0.02C 终止放电：0.2C /2.75V 终止2标称电压3.7V 3放电截止电压 2.75V 标准：2.75V 4最高充电电压4.20V±0.03V 标准：4.20V5最大持续充电电流1000mA 6最大持续放电电流5000mA 7工作温度范围充电：0℃～45℃放电：-20℃～55℃8储存温度范围-20℃～45℃IMP225069S4.2最大外形尺寸:厚度(H)*宽度(W)*高度(L)为23.5mm*51mm*72mm5．外观电池表面无明显划伤、裂纹、脏点、锈蚀、变形、变色、漏液等缺陷。
6．特性6.1电性能序号项目标准测试方法1标准充电在环境温度为23℃±2℃的条件下，以0.2CA的恒定电流充电至限定电压后恒压充电，直至充电电流小于或等于0.02CA。
2标准放电在环境温度为23℃±2℃的条件下，以0.2CA恒定电流放电至端电压达到终止电压。
3额定容量5000mAh 在环境温度为23℃±2℃的条件下，标准充电后再标准放电，可循环5次，当有一次放电容量达到额定容量，即可终止。
聚合物锂离子电池产品规格书说明书
Product Specification for Li-ion Polymer Battery 聚合物锂离子电池产品规格书Model电芯型号:503465(PCM)Prepared by制定Checked by审核Approved by批准Chen jieCustomer Approval 客户确认Checked/date审核/日期Approval/date确认/日期惠州基安比新能源有限公司HUIZHOU MARKYN NEW ENERGY CO.,LTD.电话:************传真:************ TEL:************FAX:************ SPECIFICATION AMENDMENT RECORDS规格书变更记录Edition 版本Description描述Date日期Approved审核A/0初版发行2016-12-211.Scope 适用范围：This document describes the Product Specification of the Li-Polymer Rechargeable Battery supplied by Huizhou Markyn New Energy Co.,LTD.本规格书描述了惠州基安比新能源有限公司的可充电锂离子聚合物电池的产品性能指标。
2.Description 说明2.1Description:Li-Polymer Battery类型：锂离子聚合物电池2.2Model:503465型号：5034653.Specification 产品规格3.1Basic Performance 基本性能No.序号Item 项目Spec 特性Note 备注1Nominal Capacity 容量Typ:1300mAh@0.5C Discharge(放电)Min ≥1250mAh 0.5Crate,3.0V cut-off2Nominal Voltage 标称电压3.7V 3MAX Charge Voltage 充电限制电压4.2V 4DischargeCut-Off Voltage放电截止电压 3.0V5Charge current 充电电流标准充电Standard charge ：0.2C 快速充电Rapid charge ：0.5C6Standard charging 标准充电0.2C 恒流充电至4.2V ，再4.2V 恒压充电至充电电流≤0.02C0.2C CC （constant current ）charge to 4.2V,then 4.2V CV(constant voltage)charge till charge current decline to ≤0.02C7Discharge Current 放电电流Standard Discharge:0.5C 标准放电电流：0.5C Max Discharge:1.0C 最大放电电流：1.0C8Storage temperature 储存温度1month 1个月：-10～45℃6month 6个月：-10～35℃20±5℃is recommend long term storage temperature推荐长期储存温度20±5℃9Weight重量Approx:27.5g 约:27.5g10Operating temperature 工作温度Charging充电：0～+45℃，湿度≤85%RHDischarge放电：-10～+60℃，湿度≤85%RH禁止0度以下充电＜0℃Charge shallbe prohibited11Cell Voltage电池出货电压3.8~4.0V As of shipment运输4.Battery Cell Performance Criteria电芯性能标准4.1Standard testing environment标准测试环境Unless specifically stated otherwise,tests must be done within one month of delivery and the number of charging-recharging cycles is fewer than5.The following is test conditions:Test conditions:Ambient Temperature：23ºC±2ºCAmbient Humidity：65±20%RH除非另有说明，测试应在电池出货的1个月内进行，且充放电循环的次数少于5次。
锂离子电池规格书-HDCF26650-4000mAh-3.2V说明书
锂离子电芯规格书SpecificationForLithium-ion Rechargeable Cell电芯型号:HDCF26650-4000mAh-3.2V Cell Type :HDCF26650-4000mAh-3.2V地址：山东省枣庄市台儿庄区台儿庄经济开发区广进路Address:Guangjin road,taierzhuang economic development zone,taierzhuang district,zaozhuang city,shandong provinceTel/Fax ：+86-************编制/Designed 审核/Checked 批准/Approved 日期/Effective DateContents目录1Preface前言2Definition定义2.1Rated capacity and minimum capacity标称容量与最小容量2.2Standard charge method标准充电方式2.3Standard discharge method标准放电方式3Cell type，bar code电芯型号，喷码3.1Description and model电芯说明及型号3.2Cell bar code and explanation电芯喷码及说明4Characteristics电池性能4.1Cell specification电芯特性4.2Cell dimensions电芯尺寸5Technical requirements技术要求5.1Cell storage conditions电芯存储环境5.2Cell testing conditions电芯测试条件5.3Requirement of the testing equipment测量仪表要求5.4Electronic performance电性能5.5Safety characteristics安全性能5.6Environmental characteristic s环境适应性能6The restriction of the use of hazardous substances有害物质控制要求7Contact information联系方式8Version history变更记录Warning and cautions in handling the lithium-ion cell电芯使用时警告事项及注意事项1Preface 前言This specification describes the type and dimensions ,performance,technical characteristics,warning and caution of the lithium ion rechargeable cell.The specification only applies to 26650cell supplied by Haidi Power Technology Co.,Ltd.本标准描述了圆柱型锂离子电芯的外型尺寸、特性、技术要求及注意事项。
远东电池-21700-5000mAh-锂离子电池规格书说明书
3.6V/5.0Ah 锂离子电芯规格书Specification for 3.6V/5.0Ah Lithium-ion Rechargeable Cell电芯型号: 21700-5000mAhCell type: 21700-5000mAhContents 目录1 Preface 前言2 Cell type，Barcode，Color 电芯型号、喷码、颜色2.1 Description and model 电芯说明及型号2.2 Cell barcode 电芯喷码2.3 Cell color电芯套膜颜色3 Nominal Specification标准规格4 Technical requirements技术要求4.1 Cell testing conditions电芯测试条件4.2 Requirement of the testing equipment测量仪表要求4.3 Standard charge 标准充电4.4 Standard discharge 标准放电4.5 Characteristics电池性能4.6 Safety characteristics安全性能4.7 Package schematic diagram 包装示意图5 Cell safety criterion 电芯安全准则5.1 Design and usage of chargers and battery packs充电器和电池组设计及使用注意事项5.2 Safety regulations安全守则6 The restriction for the use of hazardous substances有害物质控制要求7 Contact information联系方式8 Version change record修改记录Note: Jiangxi Far East Battery co., LTD. Hereinafter referred to as Far East Battery（FEB）注：江西远东电池有限公司以下简称远东电池（FEB）；1Preface 前言This specification describes the type, dimensions, performance, technical characteristics, warning and caution of the lithium ion rechargeable cell. The specification only applies to 21700 cell supplied by Jiangxi Far East Battery co. LTD.本标准描述了圆柱型锂离子电芯的外型尺寸、特性、技术要求及注意事项，本标准适用于江西远东电池有限公司生产的圆柱型21700锂离子电芯。
Polymer 锂离子电池产品规格说明书
Specification Approval Sheet Name：Polymer Lithium-Ion BatteryModel： CELLEVIA BATTERIES LP573450SPEC：3.7V/ 980mAhNumber: 573450Specification Modification RecordsContent1.Scope:This specification describes the Product Specification of chargeable Polymer Lithium-IonBattery produced by Cellevia.Any copies are invalid without our company’s approval2.Model :3.Cell parameters Index:3.2 Parameters of batterythe temperature.4.Electronic Characteristics test and inspection:4.1 Standard testing environmentUnless special stated, tests should be done within one month of delivery and thecharging-recharging times is less than 5 times. The following is test conditions: Ambient Temperature： 25℃±0.5℃Ambient Humidity： 65 ±20%4.2 The requirement of measure instrument(1) The measure instrument is passed tested by qualified institute.(2) The accuracy of the size instrument is not more than 0.01mm.(3) The accuracy of multimeter is not less than 0.5%. while measure the voltage, theinternal resistance mustn’t less than 10KΩ.(4) The principal of the internal resistance is 1KHz LCR, the accuracy is 0.2%.(5) The internal resistance is changeable, it varies according to the temperature and thecharging mode. And it is relevant to the PTC and the length and the Capacity of the drawing line.(6) The current accuracy of the battery test system is more than ±0.1%,isobaricallyaccuracy is ±0.5%, timer accuracy is less than ±0.1%.(7) The accuracy of the temperature meter is less than ±0.5℃.4.3 Visual inspectionAny visual inspection defects will affect the electronic characteristics, such as cracks,leakage, and flaw, are not inexistence.Notes： The Max. voltage while charging is not more than 4.25V.The Max.protective voltage designed on PCB board should not more than4.3V.5. Storage and others5.1 Long Period StorageIf the cell has been stored for 3 month, it should be transfer to a dry and cool environment. Storage Voltage is between 3.6V and 3.9V and the storage conditions as Item 4.1.5.2Any matters that this specification does not cover should be conferred between theSpecification Approval sheet6.Drawing6.1 Assembly diagram(not in scale)Model：L573450! Danger●Strictly prohibits heat or throw cell into fire.●Strictly prohibits throw and wet cell in liquid such as water, gasoline or drink etc.●Strictly prohibits use leave cell close to fire or inside of a car where temperature may be above60°C. Also do not charge / discharge in such conditions.●Strictly prohibits put batteries in your pockets or a bag together with metal objects such asnecklaces. Hairpins,coins, or screws. Do not store or transportation batteries with such objects.●Strictly prohibits short circuit the (+) and (-) terminals with other metals.●Do not place Cell in a device with the (+) and (-) in the wrong way around.●Strictly prohibits pierce Cell with a sharp object such as a needle.●Strictly prohibits disassemble or modify the cell.●Strictly prohibits welding a cell directly.●Do not use a Cell with serious scar or deformation.●Thoroughly read the user’s manual before use, inaccurate handling of lithium ion rechargeablecell may cause leakage, heat, smoke, an explosion, or fire, capacity decreasing.! Warning●Strictly prohibits put cell into a microwave oven, dryer, or high-pressure container.●Strictly prohibits use cell with dry cells and other primary batteries, or new and old battery orbatteries of a different package, type, or brand.●Stop charging the Cell if charging is not completed within the specified time.●Stop using the Cell if abnormal heat, odor, discoloration, deformation or abnormal condition isdetected during use, charge, or storage.●Keep away from fire immediately when leakage or foul odor is detected.●If liquid leaks onto your skin or clothes, wash well with fresh water immediately.●If liquid leaking from the Cell gets into your eyes, do not rub your eyes. Wash them well with cleanedible oil and go to see a doctor immediately.! Caution●Before using the Cell, be sure to read the user’s manual and cautions on handling thoroughly.●Charging with specific charger according to product specification. Charge with CC/CV method.Strictly prohibits revered charging. Connect cell reverse will not charge the cel. At the sametime, it will reduce the charge-discharge characteristics and safety characteristics, this will leadto product heat and leakage.●Store batteries out of reach of children so that they are not accidentally swallowed.●If younger children use the Cell, their guardians should explain the proper handling.●Before using the Cell, be sure to read the user’s manual and cautions on handling thoroughly.●Batteries have life cycles. If the time that the Cell powers equipment becomes much shorter thanusual, the Cell life is at an end. Replace the Cell with a new same one.●When not using Cell for an extended period, remove it from the equipment and store in aplace with low humidity and low temperature.●While the Cell pack is charged, used and stored, keep it away from objects or materials with staticelectric charges.●If the terminals of the Cell become dirty, wipe with a dry clothe before using the Cell.●Storage the cells in storage temperature range as the specifications, After full discharged, wesuggest that charging to 3.9~4.0V with no using for a long time.●Do not exceed these ranges of the following temperature ranges.Charge temperature range : 0 °C to 45 °C;Discharge temperature range : -20 °C to 60 °C.(When using equipment)Handling Precaution and GuidelineFor LIP (Lithium-Ion Polymer) Rechargeable BatteriesPrefaceThis document of ‘Handling Precautions and Guideline LIP Rechargeable Batteries’shall be applied to the battery cells manufactured by CELLEVIA.Note (1): The customer is requested to contact CELLEVIA in advance, if and when the customer needs other applications of operating conditions than those described in this document. Additional experimentation may be required to verify performance and safety under such condition.Note (2): CELLEVIA will take no responsibility for any accident when the cell is used under other condition.Note (3): CELLEVIA will inform, in a written form, the customer of improvement(s) regarding proper use and handling of the cell, if it is deemed necessary.1. Charging 1.1ChargingCurrent:Charging current should be less than maximum charge current specified in theSpecification Approval Sheet.1.2 Charging Voltage:Charging voltage should be less than the maximum nominal voltage 4.2V, andthe charging voltage upper limited is 4.30V(single pack).1.3 Charging Temperature:The cell should be charged within the range specified in this Specification ApprovalSheet.1.4 Notes:Since charging with constant current or constant voltage, reverse charging isprohibited. In case of the cell is connected improperly, the cell cannot be charged.Simultaneously, the reverse charging may cause damaging to the cell whichmay lead to degradation of cell performance and damage the cell safety, andcould cause heat generation or leakage.2. Discharging Current:The cell shall be discharged at less than the maximum discharge current specified in the Specification Approval Sheet. High discharging current may reduce the discharging capacity significantly or cause over-heat.3. Discharging TemperatureDischarging Temperature should be within the range specified in this Specification Approval Sheet.4.Over-DischargeOver-discharging will cause cell low-performance and function loss. The cell would be in a over-discharged state by its self-discharge characteristic. In order to prevent over-discharging, the cell shall be charged periodically to maintain between 3.6V and 3.9V.5. Protective Circuit Module5.1 The cell / battery pack shall be with a PCM that can protect cell / battery packproperly. PCM shall have functions of(1) Overcharging prevention(2) Over-discharging prevention(3) Over current prevention to maintain safety and prevent significant deteriorationof cell performance. The over current can occur by external short circuit.5.2 Overcharging ProtectionOvercharging prevention function shall stop charging if any cell of the battery packreaches 4.30V.5.3 Over-discharging protectionOver-discharging protection function shall monitor the voltage of every cell in the pack, and work to avoid further drop in the cell voltage of 2.75V or less.6. StorageCells should be stored in proper temperature specified in Specification ApprovalSheet.7. AppearanceIt shall be free from any defects such as remarkable scratches, breaks, cracks,discoloration, leakage or deformation .8. Notice△!8.1 Handling of cells:Avoid any short-circuit, it will caused the pole hot and lost electronic functions.Soft packing is very damaged by sharp edge parts such as needles and knives.Avoid cells touch with sharp edge part, when handling and storage.Beside the poles is the sealed edge. Don’t bend or fold dealing edge, for it is a sensitive part.Don’t open the folding edge on both sides of the cells.Don’t bend the tabs, for the tabs are not so stubborn.Avoid mechanical shock to the cells.Don’t put the cells into the heater, washing machine or high-voltage container.Don’t use the charger without any safety guarantee, and recommend you use specified charger.You should immediately stop charging, as cell is overheating, delivery any smell, changed color, distortion etc.Before Children use batteries, adults should explain the usage first.Before use batteries, please read the handling guideline carefully and fully understand.Away from the static-electronic field, while using, charging and storing cells.Don’t put the cells together with metal conductors such as chains, barrette, bolt into the pocket or stored them together.Don’t use metal conductor to shortcut the positive and negative poles.Don’t mis-assemble the positive pole with the negative one.8.2 Notice for Designing Battery Pack8.2.1 Package DesignBattery pack should have sufficient strength and battery should be protected from mechanical shock.No sharp edge components should be inside the pack containing the battery.The overcharge threshold voltage should not be exceed 4.30V (single pack)The over-discharge threshold voltage should not be lower than 2.75V (single pack)The PCM should have short protection built inside.8.3 Notice for Assembling Battery Pack8.3.2 Tab connectionUltrasonic welding or spot welding is recommended to connect battery with PCM or other parts.If apply manual solder method to connect tab with PCM, below notice is very important to ensure battery performance.8.3.2.1 The solder iron should be temperature controlled and ESDsafe.8.3.2.2 Soldering temperature should not exceed 350℃.8.3.2.3 Soldering time should not be longer than 3 seconds .8.3.2.4 Keep battery tab cold down before next time soldering.8.3.2.5 Directly heat cell body is strictly prohibited. Battery shouldbe damaged by heat above approx. 60℃.8.3.3 Cell fixingThe battery should be fixed to the battery pack by its large surface area.No sharp edge at the assembling position.No cell movement in the battery pack should be allowed.9.Others9.1 The disassembling may generate internal shout circuit in the cell, which may causegassing, firing, or other problem.9.2 Prohibition of dumping of cells into fireNever incinerate or dispose the cells in fire, for these may cause firing of the cells.9.3 The cells should never be soaked with liquids such as water, drinks or oil.9.4 Prohibit using the cells mixed with different manufactories. Prohibit using new cellsmixed with old ones.▲Special Notice: If the cell isn’t used for a long time, Please Keep the cells in half-charged state, which is keeping them unfully charged or incompletely discharged. Recharge the cells and use half of the power after 2-3months. Store the cells in cool and dry place. It will protect the cell from damage effectively and long-term.10. StatementIf our specifications material, product process or product control system has changed, the information will be transmitted to consumer by way of written with quality and reliability data.。
TY-18650-1900mAh产品规格书
7.2.3测量时间用的仪表准确度不低于±0.1％。 7.2.4测量温度的仪表准确度不低于±0.5℃。
7.2.5称量重量的电子天平准确度不低于±0.5％。 7.2.6测量外形尺寸的量具，其分度值不大于1mm。 7.2.7恒流源的电流可调，在恒流充电或放电过程中，电流变化在±1％范围内。
7.2.8恒压源的电压可调，在恒压充电过程中，电压变化在±1％范围内。 7.3充放电方法 7.3.1标准充电：以恒流0.5CtA充电，当电池的端电压达到4.2V时，改为恒压充电， 直到充电电流小于或等于0.01CtA，最长时间不大于8h，停止充电。 7.3.2快速充电：以恒流1CtA充电，当电池的端电压达到4.2V时，改为恒压充电，直 到充电电流小于或等于0.01CtA，停止充电。
2
热冲击性能
产品按7.6.2规定进行试验，不起火、不爆炸。
3
模拟海拔高度 产品按7.6.3规定进行试验，不泄漏、不起火、不爆炸。
7.0试验方法 7.1试验条件
温度：25±2℃，相对湿度：45±20%（除非另外要求）。 7.2测量仪表和设备要求 7.2.1测量电压的仪表准确度不低于±0.5％。
7.2.2测量电流的仪表准确度不低于±0.5％。
晰。 6.0性能 6.1电性能
序号
1 2
项目 开路电压
内阻
≥3.90V。 ≤60mΩ。
标准
3
0.2C5A放电
产品按7.4.1试验，放电时间≥5h。
4
1C5A放电
产品按7.4.2试验，放电时间≥57min。
5
2C5A放电
产品按7.4.3试验，放电时间≥27min。
6
循环寿命
产品按7.4.4试验，寿命≥300次。
1.0目的 对可充锂离子电池的产品规格、测试方法进行规范，避免因测试条件、方法的不同
锂电池规格书
锂电池规格书41922(总12页) -本页仅作为预览文档封面，使用时请删除本页-储能型磷酸铁锂电池规格书STORAGE LiFePO4 BATTERY SPECIFICATIONS客户名称(Customer)：产品型号(Type)： CF12V80Ah发行日期(Issuing Date)：1. 适用范围(Product Scope)本规格书描述了锂离子二次电池的技术要求、测量方法、运输、储存及注意事项。
This Specification describes the requirements of the lithium ion rechargeable battery supplied by2. 电池组特性 (Battery Group Specifications)单只电芯曲线图feature curve for single cellManagement system管理系统Single cell over-charge cut-off voltage单只过压保护值Charge Working voltage过压释放值Single cell under-discharge cut-offvoltage单只欠压保护值Discharge working voltage欠压释放值Conditions of over-charge and under-discharge voltage recovery过、欠压恢复条件With the high-point voltage reaching the workingvoltage 极限电压达到释放值Over-charge cut-off current 过流保护值80AShort-circuit protection 短路保护Own this ability 具备此功能Condition for the recovery of over-current and short-circuit protection过流\短路保护恢复条件Cut the circuit to automatic recovery断开负载自动恢复3. 技术要求(Technical Requirements)测试条件(除特别规定) Testing Conditions (unless otherwise specified) 温度Temperature: 15~35℃相对湿度Relative Humidity: 45%~75%大气压Atmospheric pressure: 86~106Kpa充放电性能 (Electrical Characteristics)环境性能 (Environmental Characteristic)机械性能 (Mechanical characteristics)安全性能 (Safe Characteristic)After standard charge，the battery located in afume hood is to be short-circuited by connectingthe positive and negative terminals with anexternal l oad of less than 50 mΩ till the batterycase temperature has returned to near ambienttemperature.将标准充电后的电池置于通风橱中，短路其正负极（线路总电阻不大于50m），实验过程中监视电池温度变化，当电池温度下降到接近初始室温时，结束实验4 电池组基本性能 (Basic Characteristics of Battery)<400 m5 电池组保护功能要求 (Battery Required Protection Functions)To insure the safety, charger and the protection circuit shall be satisfied the items below. As safety device, please use in combination with the temperature fuse. The standard charge method is CC/CV (constant current/constant voltage)为确保安全,充电器和保护电路应符合以下要求。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
锂离子电池规格书型号：BL-5c
标称: 1000mAh
修订履历
1、目的
对深圳市好远通电子有限公司出品的可充锂离子电池的产品规格、测试方法进行规范，避免因测试条件、方法的不同引起误差。
2、产品类别和产品型号
2.1 类别：锂离子可充电池
2.2 产品型号高务电池BL-5C/1000mAh
3、产品基本特性
4、特性
4.1电性能
4.2 安全性能
4.3 环境适应性
温度：25±2℃，相对湿度：45±20%（除非另外要求）
6、产品责任书
消费者必须严格遵守深圳市好远通电子有限公司规格书和文件后面的注示使用电池，由于误用会引起电池过热，发生火灾或爆炸，对于没有按照规格书进行操作所造成的任何意外事故，深圳市慧通天下科技股份有限公司不负任何责任。
7、充电前注意事项
如果规格书、原材料、生产过程或生产控制系统发生改变，改变的信息将会随质量和可靠性数据以书面形式通知消费者。
8、电池包装说明
在电池的包装上应有如下说明
！危险
*充电时请使用指定的充电器并按照说明书的要求进行充电。
*仅在指定的设备上使用电池。
*不要把电池加热或投进火中。
*不要在火源附近或温度超过60℃的轿车中使用或遗留电池，也不要在这些环境中进行充电。
*不要把电池投入水中，也不要弄湿。
*不要把电池同项链、发夹、硬币或镙钉等金属品一起放在兜里或包中，也不要把电池同上述物品一起储存。
*不要使用金属导体短路电池的正负极。
*在装入设备时注意电池的正负极不要反装。
*不要使用锐利的物品刺穿电池。
*不要对电池进行分解。
*不要直接对电池进行焊接。
*不要使用带有严重伤痕或变形的电池。
*在使用之前请详细阅读操作说明书，不适当的操作可能引起电池变热、着火、爆炸、毁坏或电池容量的衰减。
！警告
*不要把电池放在加热器皿、洗衣机或高压容器中。
*不要把电池同干电池或其它原电池一起使用，也不要同不同包装、不同型号或不同品牌的电池一起使用。
*如果在规定的充电时间内充电没有结束，停止充电。
*在使用、充电或储存期间如发现电池有变热、散发气味、变色、变形或其它反常应停止使用。
*当发现电池漏液到皮肤或衣服上，立刻用清水清洗。
*如果电解液渗出并进入眼睛里，不要揉擦眼睛，立刻用干净的水清洗并去看医生。
！注意
*把电池放到小孩够不到的地方以免吞服。
*小孩使用电池时，监护人应详细解释操作方法。
*在使用电池之前，应详细阅读操作指南并对使用中的注意事项有足够深刻的理解。
*在对电池充电之前仔细阅读操作指南。
*在将电池装入设备或从设备中取出之前详细阅读设备操作手册。
*电池具有使用寿命，如果使用电池的设备的工作时间比平常少得多，要对电池进行更换。
*电池寿命终止后要立刻从设备中取出。
*当长期不用时，要将电池从设备中取出并放在低温低湿的环境中保存。
*电池应在远离静电的场所进行充电、使用和储存。
*如果电池的接线端变脏，在使用之前用干布擦净。
*电池在使用时的温度不能超出下面的要求：
*充电温度范围：0℃ to 45℃
*放电温度范围：-20℃ to 60℃
9、电池外型：
10、主要零部件
11、保护板规格
11.1保护板性能
过充电保护电压: 4.30V±0.05V
过放电保护电压: 2.40V±0.10V
过电流保护: 2.0A - 5.0A
工作时自耗电: 2.5µA(典型) 7.0µA(最大)
休眼时自耗电: 0.1µA(典型) 1.0µA(最大)
保护板内阻: 30—60mΩ
11.2 工作原理图
序号名称规格单位用量
所长
位置1电容0.1µF 10% 10V 0603 PCS1C1
2
电阻100Ω 5% 1/16W 0603 PCS1R1
310KΩ 5% 1/16W 0603PCS1R3 41KΩ 5% 1/16W 0603 PCS1R2 5MOS管S8205 PCS1U2 6控制IC DW01+ PCS1U1
R3。