注塑方面英语术语
注塑常用术语英文表达
1.雾气Moisture Streaks2。
玻纤分配不均Glass Fiber Streaks3.困气Gas Trap Effect4。
银丝纹Sliver Marks5.结合线Weld Line6.水波痕Water Wave Effect7。
黑点Dark Sport8。
顶出印Visible Ejector Marks9。
变形Deformation During Demolding10.填充不足Short Filling11。
冷料流痕Cold Slug12。
进胶口点不良Dull Spots Near The Sprue13。
喷射痕Jetting14.表面起层Flaking Of The Surface Layer15.浮泡Entrapped Air16。
过热变色Burnt Streaks17。
龟裂Stress Crack18。
缩水痕Sink Marks19。
真空气泡Density Bubble20。
披锋Flash21。
擦伤印Scratch MarksGlass fiber rich surface/glass emergence on the surface 22 尺寸过大Over dimension23尺寸过小Under dimension24 翘曲Warpage/warped25 收缩Shrinkage/shrink26 缩影Sink marks27 打不满Short shot/short molding塑料模具mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板support plate方铁spacer plate底针板ejector plate面针板ejector retainer plate回针Return pin导柱Guide pin有托导套Shoulder Guide bush直导套Straight Guide bush动模座板Bottom clamp plate Moving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch—retainer plate顶针ejector pin单腔模具single cavity mould多腔模具multi—cavity mould多浇口multi—gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道sprue分流道runner浇口gate直浇口direct gate ，sprue gate轮辐浇口spoke gate ，spider gate 点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold—slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould 动模movable mould，movable half 上模upper mould, upper half下模lower mould，lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin，finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具three plate mould脱模ejection换模腔模具interchangeable cavity mould脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller 立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine。
注塑方面英语术语共22页文档
注塑方面英语术语压铸 die-cast压炼 injection铸件 casting/cast/founding起泡/气泡 bubble/blister/air bubble缺料 shor-shots/undershot浇不足/*铸 under-founding多料 superfluit ies/superfluous material(alloy)顶针痕 ejector (pins)mark花纹 flowmark/flow line冷纹 coldmark/cold streak油纹 oilstreak走水纹 splash mark银纹 silverstreaks霜纹 splaymark夹水纹 silverstreaks/flow line/weld line扣模/粘模 sprue sticking 砂眼/气眼 air hole（塑胶件）弯曲/变形 warping/warpage变形 deformation扭曲 twist翅曲 warp/warped材料错误 using wrongplastic material凸痕 convex mark凹位/凹陷 sink mark/dentmark披锋 flashing批损 pare-mark/cut mark批凹 pareoff锉纹 trim-mark/file-mark锉损 excessive trim mark黑点/黑纹 black spots/blackstreak发白 white mark烧焦 burnmarks刮花/刮痕 scratch mark擦痕/擦伤 rub-mark/brush-burn裂缝 cracking裂纹 craking line碰损 stress mark起皮 chip错位（合模线） part line misaling ment孔位尺寸改变 dimension various哑色 dull color表面变光滑（喷油面） glossy finishing表面sruface/outside镶件insert/insert word缩水/收缩 sinkmark/shrinkage/shrink mark偏差 color deviation色粉 colourment颜色 colour/color零件污糟 dirty mark onpart顶白 stress mark/ejector mark屈曲 bent夹模线移位 part linemisalignment胶件料厚不均 uneven wall thickness水口料 degradedmaterial凹印 sink mark擦花 abrasion mark混色 contamination mark热点不良 poor heatsticking定位圈 locatingring唧嘴 sprue bush (浇口套)A板 Aplate (定模板)B板 Bplate（动模板）方铁 spacer block (垫铁)底板 bottom clamp plate(动模底板)面板 topclamp plate(定模底板)顶针 ejector pin（顶杆）直边钉 guide pin(导柱)托司 shoulder guide bush(导套)直司 straightguide bush(导柱)回针 returnpin(回程杆)细水口边钉 support pin(副导柱)蓝弹簧 blue spring（回程弹簧）水口推板 runner stripperplate(卸流道板)中边钉 ejector guidepin (顶板导柱)顶针板 ejectorretainer plate(顶杆固定板)顶针底板 ejector plate(顶杆垫板)撑头 support pollar（支撑柱）垃圾钉 stop pin(限位钉)呵core (后模肉内镶件)后模肉 back moldbody(后模镶件)前模肉 cavity（前模镶件）扣鸡 P-lockblister 起泡blooming 起霜blow hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡center buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕orange peel 橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap 废料scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮折迭straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱折surging 波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)毛边flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤(Flow Line)流痕(Weld Line) 熔接线Sink Mark凹陷Streak条纹Warpage翘曲希望以上资料对你有所帮助，附励志名言3条：1、有志者自有千计万计，无志者只感千难万难。
注塑行业英语词汇
注塑词汇Injection machine 啤机Shot size（weight）实际射胶量 injection volume 理论射胶量 min mold height 最小容模厚度Max mold height 最大容模厚度 Tie bar clearance 拉杆间距 Die plate size 模板尺寸 Ejector stroke 顶出行程 barrel 炮筒，机筒 clamp force 锁模力 non-return valve 止回阀shear 剪切 opening 开模行程Injection pressure 射胶压力back pressure 背压 nozzle size 射咀尺寸Cycle time 循环周期down time 停机时间 hopper 料筒Mold release 脱模剂lubrication 润滑 work horse 主力，主要设备Reserve pressure / packing pressure保压mold trial 试模 shot （一）啤Decompress 减压oven 烤炉，烘灶 shrinkage rate 收缩率Residence time 滞留时间injection speed 注射速度 booster time 增压时间Compression ratio 压缩比 mold close time 合模时间Resin 胶料Plastification 塑化，增塑viscosity 粘性，粘度contamination 污染，杂物Thermoplastic 热塑性塑料thermosetting plastics 热固性塑料Booster time 增压时间 feed 喂料，填充purge 净化Flame retardant 阻燃 degradation 降解，软化 regrind 再粉碎Water absorption 吸水reinforce 增强，加固 specific gravity 比重Elongation 延伸率 density 密度 melting point 熔点Polystyrene 聚苯乙烯（PS） Styrene 苯乙烯Acrylonitrile 丙烯腈Polypropylene 聚丙烯（PP） Polyethylene 聚乙烯 glass fiber 玻纤Condensation 凝固，浓缩 crystalline resin 结晶形塑料compre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold分割式模具cavity 型控母模core 模心公模taper 锥拔leather cloak 仿皮革shiver 饰纹flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝striper plate 脱料板piston 活塞cylinder 汽缸套chip 细碎物handle mold 手持式模具（移转成型用模具）encapsulation molding 低压封装成型（射出成型用模具）two plate 两极式（模具）well type 蓄料井insulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块valve gate 阀门浇口band heater 环带状的电热器spindle 阀针spear head 刨尖头slag well 冷料井cold slag 冷料渣air vent 排气道welding line 熔合痕eject pin 顶出针knock pin 顶出销return pin 回位销反顶针sleave 套筒stripper plate 脱料板insert core 放置入子nner stripper plate 浇道脱料板guide pin 导销eject rod (bar)（成型机）顶业捧subzero 深冷处理three plate 三极式模具runner system 浇道系统stress crack 应力电裂orientation 定向sprue gate 射料浇口，直浇口nozzle 射嘴sprue lock pin 料头钩销(拉料杆) slag well 冷料井side gate 侧浇口edge gate 侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口fan gate 扇形浇口dish gate 因盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口subarine gate 潜入式浇口tunnel gate 隧道式浇口pin gate 针点浇口Runner less 无浇道(sprue less) 无射料管方式long nozzle 延长喷嘴方式sprue 浇口;溶渣入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 流道: runner 热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴：hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头：connector plug 插座： connector socket 密封/封料： seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin 顶针板：ejector retainner plate 托板：support plate 螺丝： screw 管钉：dowel pin 开模槽：ply bar scot 内模管位：core/cavity inter-lock 顶针：ejector pin 司筒：ejector sleeve 司筒针：ejector pin 推板：stripper plate 缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter 模胚（架）： mold base 上内模：cavity insert 下内模：core insert 行位（滑块）： slide 镶件：insert 压座/斜鸡：wedge 耐磨板/油板：wedge wear plate 压条：plate 撑头: support pillar 唧嘴： sprue bushing 挡板：stop plate 定位圈：locating ring 锁扣：latch 扣鸡：parting lock set 推杆：push bar 栓打螺丝：S.H.S.B 顶板：eracuretun 活动臂：lever arm 分流锥：spure sperader 水口司:bush 垃圾钉：stop pin 隔片：buffle 弹弓柱：spring rod 弹弓:die spring 中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin 销子：dowel pin 波子弹弓：ball catch 喉塞: pipe plug 锁模块：lock plate 斜顶：angle from pin 斜顶杆：angle ejector rod 尼龙拉勾：parting locks 活动臂：lever arm 复位键、提前回杆：early return bar 气阀：valves 斜导边：angle pin 术语：terms 承压平面平衡：parting surface support balance 模排气：parting line venting 回针碰料位：return pin and cavity interference 模总高超出啤机规格：mold base shut hight 顶针碰运水：water line interferes withejector pin 料位出上/下模：part from cavith (core) side 模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate. 不准用镶件： Do not use (core/cavity) insert 用铍铜做镶件： use beryllium copper insert 初步（正式）模图设计：preliinary (final) mold design 反呵：reverse core 弹弓压缩量：spring compressed length 稳定性好：good stability,stable 强度不够：insufficient rigidity 均匀冷却：even cooling 扣模：sticking 热膨胀：thero expansion 公差：tolorance 铜公(电极）：copper electrode塑料成形模具 mould for plastics 热塑性塑料模 mould for thermoplastics 热固性塑料模 mould for thermosets 压缩模 compression mould 压注模、传递模 transfer mould 注射模 injection mould 热塑性塑料注射模 injection mould for thermoplastics 热固性塑料注射模 injection mould for thermoses 定模 stationary mould fixed half 动模 movable mould moving half 定模座板 fixed clamp plate, top clamping plate. top plate 动模座板 moving clamp plate. bottom clamping plate. bottom plate 上模座板 upper clamping plate 下模座板 lower clamping plate 凹模固定板 cavity-retainer plate 型芯固定板 core-retainer plate 凸模固定板 punch-retainer plate 模套 chase. bolster. frame 支承板 backing plate. supprr plate 垫块 spacer parallel 支架 ejector housing. mould base leg abrasive grinding 强力injection mould 注塑模injection 注射in-line-of-draw 直接脱模insert 嵌件inserted die 嵌入式凹模inspection检查,监督installation安装Surface Appearance 外观Glossiness/gloss finish 光洁度Matt finish/matt surface 毛面Glass fiber richsurface/glass emergence on the surface 玻纤外露Blooming/surface blooming 表面析出White patches on surface 表面白斑Silver marks/silver streak 银纹Splay mark 水纹Flow mark 流纹Weld line 溶结纹Brittle/brittleness 脆Bubbles/trapped gas 气泡V oid 孔Burn marks 烧伤FR failed 阻燃不合格Flame rating V-2 阻燃V-2 Poor dispersion 分散不好FR/PTFE …agglomerates etc 阻燃剂/PTFE…结块Pellet porous 粒子不密/蜜蜂窝Low impact/tensile etc 物理性能低High flow/filler content etc 流动性/填充…过高Longs/fines/doubles 长粒/碎屑/连粒Poor cut 粒形不好Bristle/voids 表面有小气泡/孔Glass bundles 玻纤结团Product was rejected due to 产品不能接受因为… High moisture level 高水分Warpage/warped 翘曲Shrinkage/shrink 收缩Sink marks 缩影Short shot/short molding 打不满Distortion 变形Over dimension 尺寸过大Under dimension 尺寸过小Flashing 飞边Discoloration 变色Off color 颜色差异Flow rate 流动率Viscous 粘High flow 高流动Low flow 低流动Sticky 粘Mold release 脱模Antioxidant 抗氧剂Flame retardant agent 阻燃剂Heat stabilizer 热稳定剂Chopped glass fiber 短切玻纤Roving glass fiber 粗纱/长玻纤Glass beads 玻璃微珠Milled fiber 碾磨纤Molybdenum disulfide/moly/MoS2 二硫化钼Colorant 着色剂Pigment 颜料Dye 染料Accepted product specification 接受产品规格Approved our product 认可我们的产品Re-set spec 重新定标准Add in extra … 添加多一点… Reduced … content 减少…含量Dropped/redu ced … by x％减少…含量…％Confirmed color standard 确认颜色标准Approved color standard 认可颜色标准Re-confirmed color standard 重新确认颜色标准Qualified our product 认可我们的产品Undergoing heat aging test 在做热老化实验Product is under testing 产品在测试当中Received first order 接了第一个定单Expected to finish by … 预计在…完成Expected order is xMT 预计定单量…吨Estimated annual/monthly consumption 预计年/月用量SPC statistic process control 品管保证Quality Assurance 品管控制Quality control 来料检验IQC Incoming quality control 巡检IPQC In-process quality control 校对calibration 动态试验dynamic test 环境试验Environmental test 非破坏性试验non-destructive test 光泽gloss 击穿电压(dielectric) breakdown voltage 拉伸强度tensile strength 冷热骤变试验thermal shock test 环境试验炉Environmental chamber 盐雾实验salt spray test 绝缘电阻测试验仪Insulating resistance meter 内应力internal stress 疲劳fatigue 蠕变creep 试样specimen 撕裂强度tear strength 缩痕shrink mark, sink mark 耐久性durability 抽样sampling 样品数量sample size AQL Acceptable Quality level 批量lot size 抽样计划sampling plan OC曲线operation curve 试验顺序sequence of tests 环境温度ambient temperature 可焊性solderability 阻燃性flame resistance XX电子有限公司XX Electronics CO., Ltd 总经理办公室General manager’s office 企管部Enterprise management department (EM) 行政部Administration department (AD) 销售部Sales department (SD) 财务部Financial department (FD) 技术部Technology department (TD) 物控部Production material control department (PMC) 生产部Production department(PD) 模具部Mold manufacturing department, Tooling manufacturing department (TM) 品管部Quality Assurance department (QA) 冲压车间Stamp workshop, press workshop 注塑车间injection workshop 装配车间Assembly workshop 模具装配车间Mold and die Assembly workshop 金属加工车间metal machine workshop 电脉冲车间Electric discharge process workshop 线切割车间wire cutting process workshop 工磨车间Grinding workshop 总经理General manager (GM) 副总经理Vice-general manager 经理manager 董事长president 副董事长Vice-president XX部门经理Manager of XX department 主任、主管supervisor 拉长Line leader 组长Foreman, forelady 秘书secretary 文员clerk 操作员operator 助理assistant。
注塑英语词汇
注塑英语词汇Injection machine 啤机Shot size（weight）实际射胶量 injection volume 理论射胶量 min mold height 最小容模厚度Max mold height 最大容模厚度 Tie bar clearance 拉杆间距 Die plate size 模板尺寸 Ejector stroke 顶出行程 barrel 炮筒，机筒 clamp force 锁模力 non-return valve 止回阀shear 剪切 opening 开模行程Injection pressure 射胶压力back pressure 背压 nozzle size 射咀尺寸Cycle time 循环周期down time 停机时间 hopper 料筒Mold release 脱模剂lubrication 润滑 work horse 主力，主要设备Reserve pressure / packing pressure保压mold trial 试模 shot （一）啤Decompress 减压oven 烤炉，烘灶 shrinkage rate 收缩率Residence time 滞留时间injection speed 注射速度 booster time 增压时间Compression ratio 压缩比 mold close time 合模时间Resin 胶料Plastification 塑化，增塑viscosity 粘性，粘度contamination 污染，杂物Thermoplastic 热塑性塑料thermosetting plastics 热固性塑料Booster time 增压时间 feed 喂料，填充purge 净化Flame retardant 阻燃 degradation 降解，软化 regrind 再粉碎Water absorption 吸水reinforce 增强，加固 specific gravity 比重Elongation 延伸率 density 密度 melting point 熔点Polystyrene 聚苯乙烯（PS） Styrene 苯乙烯Acrylonitrile 丙烯腈Polypropylene 聚丙烯（PP） Polyethylene 聚乙烯 glass fiber 玻纤Condensation 凝固，浓缩 crystalline resin 结晶形塑料compre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold分割式模具cavity 型控母模core 模心公模taper 锥拔leather cloak 仿皮革shiver 饰纹flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝striper plate 脱料板piston 活塞cylinder 汽缸套chip 细碎物handle mold 手持式模具（移转成型用模具）encapsulation molding 低压封装成型（射出成型用模具）two plate 两极式（模具）well type 蓄料井insulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块valve gate 阀门浇口band heater 环带状的电热器spindle 阀针spear head 刨尖头slag well 冷料井cold slag 冷料渣air vent 排气道welding line 熔合痕eject pin 顶出针knock pin 顶出销return pin 回位销反顶针sleave 套筒stripper plate 脱料板insert core 放置入子nner stripper plate 浇道脱料板guide pin 导销eject rod (bar)（成型机）顶业捧subzero 深冷处理three plate 三极式模具runner system 浇道系统stress crack 应力电裂orientation 定向sprue gate 射料浇口，直浇口nozzle 射嘴sprue lock pin 料头钩销(拉料杆) slag well 冷料井side gate 侧浇口edge gate 侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口fan gate 扇形浇口dish gate 因盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口subarine gate 潜入式浇口tunnel gate 隧道式浇口pin gate 针点浇口Runner less 无浇道(sprue less) 无射料管方式long nozzle 延长喷嘴方式sprue 浇口;溶渣入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 流道: runner 热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴：hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头：connector plug 插座： connector socket 密封/封料： seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin 顶针板：ejector retainner plate 托板：support plate 螺丝： screw 管钉：dowel pin 开模槽：ply bar scot 内模管位：core/cavity inter-lock 顶针：ejector pin 司筒：ejector sleeve 司筒针：ejector pin 推板：stripper plate 缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter 模胚（架）： mold base 上内模：cavity insert 下内模：core insert 行位（滑块）： slide 镶件：insert 压座/斜鸡：wedge 耐磨板/油板：wedge wear plate 压条：plate 撑头: support pillar 唧嘴： sprue bushing 挡板：stop plate 定位圈：locating ring 锁扣：latch 扣鸡：parting lock set 推杆：push bar 栓打螺丝：S.H.S.B 顶板：eracuretun 活动臂：lever arm 分流锥：spure sperader 水口司:bush 垃圾钉：stop pin 隔片：buffle 弹弓柱：spring rod 弹弓:die spring 中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin 销子：dowel pin 波子弹弓：ball catch 喉塞: pipe plug 锁模块：lock plate 斜顶：angle from pin 斜顶杆：angle ejector rod 尼龙拉勾：parting locks 活动臂：lever arm 复位键、提前回杆：early return bar 气阀：valves 斜导边：angle pin 术语：terms 承压平面平衡：parting surface support balance 模排气：parting line venting 回针碰料位：return pin and cavity interference 模总高超出啤机规格：mold base shut hight 顶针碰运水：water line interferes withejector pin 料位出上/下模：part from cavith (core) side 模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate. 不准用镶件： Do not use (core/cavity) insert 用铍铜做镶件： use beryllium copper insert 初步（正式）模图设计：preliinary (final) mold design 反呵：reverse core 弹弓压缩量：spring compressed length 稳定性好：good stability,stable 强度不够：insufficient rigidity 均匀冷却：even cooling 扣模：sticking 热膨胀：thero expansion 公差：tolorance 铜公(电极）：copper electrode塑料成形模具 mould for plastics 热塑性塑料模 mould for thermoplastics 热固性塑料模 mould for thermosets 压缩模 compression mould 压注模、传递模 transfer mould 注射模 injection mould 热塑性塑料注射模 injection mould for thermoplastics 热固性塑料注射模 injection mould for thermoses 定模 stationary mould fixed half 动模 movable mould moving half 定模座板 fixed clamp plate, top clamping plate. top plate 动模座板 moving clamp plate. bottom clamping plate. bottom plate 上模座板 upper clamping plate 下模座板 lower clamping plate 凹模固定板 cavity-retainer plate 型芯固定板 core-retainer plate 凸模固定板 punch-retainer plate 模套 chase. bolster. frame 支承板 backing plate. supprr plate 垫块 spacer parallel 支架 ejector housing. mould base leg abrasive grinding 强力injection mould 注塑模injection 注射in-line-of-draw 直接脱模insert 嵌件inserted die 嵌入式凹模inspection检查,监督installation安装Surface Appearance 外观Glossiness/gloss finish 光洁度Matt finish/matt surface 毛面Glass fiber richsurface/glass emergence on the surface 玻纤外露Blooming/surface blooming 表面析出White patches on surface 表面白斑Silver marks/silver streak 银纹Splay mark 水纹Flow mark 流纹Weld line 溶结纹Brittle/brittleness 脆Bubbles/trapped gas 气泡V oid 孔Burn marks 烧伤FR failed 阻燃不合格Flame rating V-2 阻燃V-2 Poor dispersion 分散不好FR/PTFE …agglomerates etc 阻燃剂/PTFE…结块Pellet porous 粒子不密/蜜蜂窝Low impact/tensile etc 物理性能低High flow/filler content etc 流动性/填充…过高Longs/fines/doubles 长粒/碎屑/连粒Poor cut 粒形不好Bristle/voids 表面有小气泡/孔Glass bundles 玻纤结团Product was rejected due to 产品不能接受因为… High moisture level 高水分Warpage/warped 翘曲Shrinkage/shrink 收缩Sink marks 缩影Short shot/short molding 打不满Distortion 变形Over dimension 尺寸过大Under dimension 尺寸过小Flashing 飞边Discoloration 变色Off color 颜色差异Flow rate 流动率Viscous 粘High flow 高流动Low flow 低流动Sticky 粘Mold release 脱模Antioxidant 抗氧剂Flame retardant agent 阻燃剂Heat stabilizer 热稳定剂Chopped glass fiber 短切玻纤Roving glass fiber 粗纱/长玻纤Glass beads 玻璃微珠Milled fiber 碾磨纤Molybdenum disulfide/moly/MoS2 二硫化钼Colorant 着色剂Pigment 颜料Dye 染料Accepted product specification 接受产品规格Approved our product 认可我们的产品Re-set spec 重新定标准Add in extra … 添加多一点… Reduced … content 减少…含量Dropped/redu ced … by x％减少…含量…％Confirmed color standard 确认颜色标准Approved color standard 认可颜色标准Re-confirmed color standard 重新确认颜色标准Qualified our product 认可我们的产品Undergoing heat aging test 在做热老化实验Product is under testing 产品在测试当中Received first order 接了第一个定单Expected to finish by … 预计在…完成Expected order is xMT 预计定单量…吨Estimated annual/monthly consumption 预计年/月用量SPC statistic process control 品管保证Quality Assurance 品管控制Quality control 来料检验IQC Incoming quality control 巡检IPQC In-process quality control 校对calibration 动态试验dynamic test 环境试验Environmental test 非破坏性试验non-destructive test 光泽gloss 击穿电压(dielectric) breakdown voltage 拉伸强度tensile strength 冷热骤变试验thermal shock test 环境试验炉Environmental chamber 盐雾实验salt spray test 绝缘电阻测试验仪Insulating resistance meter 内应力internal stress 疲劳fatigue 蠕变creep 试样specimen 撕裂强度tear strength 缩痕shrink mark, sink mark 耐久性durability 抽样sampling 样品数量sample size AQL Acceptable Quality level 批量lot size 抽样计划sampling plan OC曲线operation curve 试验顺序sequence of tests 环境温度ambient temperature 可焊性solderability 阻燃性flame resistance XX电子有限公司XX Electronics CO., Ltd 总经理办公室General manager’s office 企管部Enterprise management department (EM) 行政部Administration department (AD) 销售部Sales department (SD) 财务部Financial department (FD) 技术部Technology department (TD) 物控部Production material control department (PMC) 生产部Production department(PD) 模具部Mold manufacturing department, Tooling manufacturing department (TM) 品管部Quality Assurance department (QA) 冲压车间Stamp workshop, press workshop 注塑车间injection workshop 装配车间Assembly workshop 模具装配车间Mold and die Assembly workshop 金属加工车间metal machine workshop 电脉冲车间Electric discharge process workshop 线切割车间wire cutting process workshop 工磨车间Grinding workshop 总经理General manager (GM) 副总经理Vice-general manager 经理manager 董事长president 副董事长Vice-president XX部门经理Manager of XX department 主任、主管supervisor 拉长Line leader 组长Foreman, forelady 秘书secretary 文员clerk 操作员operator 助理assistant。
注塑常用术语英文表达
1.雾气 Moisture Streaks2.玻纤分配不均 Glass Fiber Streaks3.困气 Gas Trap Effect4.银丝纹 Sliver Marks5.结合线 Weld Line6.水波痕 Water Wave Effect7.黑点 Dark Sport8.顶出印 Visible Ejector Marks9.变形 Deformation During Demolding10.填充不足 Short Filling11.冷料流痕 Cold Slug12.进胶口点不良 Dull Spots Near The Sprue13.喷射痕 Jetting14.表面起层 Flaking Of The Surface Layer15.浮泡 Entrapped Air16.过热变色 Burnt Streaks17.龟裂 Stress Crack18.缩水痕 Sink Marks19.真空气泡 Density Bubble20.披锋 Flash21.擦伤印 Scratch MarksGlass fiber rich surface/glass emergence on the surface22 尺寸过大 Over dimension23尺寸过小 Under dimension24 翘曲 Warpage/warped25 收缩 Shrinkage/shrink26 缩影 Sink marks27 打不满 Short shot/short molding塑料模具mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plate Top plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板 support plate方铁 spacer plate底针板 ejector plate面针板 ejector retainer plate回针 Return pin导柱 Guide pin有托导套 Shoulder Guide bush 直导套 Straight Guide bush动模座板Bottom clamp plate Moving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate 凸模固定板punch-retainer plate 顶针ejector pin单腔模具single cavity mould 多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道 sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould动模movable mould, movable half上模upper mould， upper half下模lower mould， lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具three plate mould脱模ejection换模腔模具 interchangeable cavity mould 脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床V ertical driller超声波清洗机Ultrasonic clearing machine 精品文档word文档可以编辑！谢谢下载！。
注塑方面英语术语
注塑方面英语术语注塑方面英语术语标签/分类：压铸 die-cast压炼 injection铸件 casting/cast/founding起泡/气泡 bubble/blister/airbubble缺料 shor-shots/undershot浇不足/*铸 under-founding多料 superfluities/superfluous material(alloy)顶针痕 ejector(pins) mark花纹 flow mark/flow line冷纹 cold mark/cold streak油纹 oil streak走水纹 splash mark银纹 silver streaks霜纹 splay mark夹水纹 silver streaks/flow line/weld line扣模/粘模 spruesticking砂眼/气眼 air hole（塑胶件）弯曲/变形 warping/warpage变形 deformation扭曲 twist翅曲 warp/warped材料错误 usingwrong plastic material凸痕 convex mark凹位/凹陷 sink mark/dent mark披锋 flashing批损 pare-mark/cutmark批凹 pare off锉纹 trim-mark/file-mark锉损 excessivetrim mark黑点/黑纹 black spots/black streak发白 white mark烧焦 burnmarks刮花/刮痕 scratch mark擦痕/擦伤 rub-mark/brush-burn裂缝 cracking裂纹 crakingline碰损 stress mark起皮 chip错位（合模线） part linemisaling ment孔位尺寸改变 dimensionvarious哑色 dull color表面变光滑（喷油面） glossy finishing表面 sruface/outside镶件 insert/insert word缩水/收缩 sinkmark/shrinkage/shrink mark 偏差 colordeviation色粉 colourment颜色 colour/color零件污糟 dirty mark on part顶白 stressmark/ejector mark屈曲 bent夹模线移位 part line misalignment胶件料厚不均 uneven wall thickness水口料 degradedmaterial凹印 sink mark擦花 abrasionmark混色 contamination mark热点不良 poor heat sticking模具方面：定位圈 locating ring唧嘴 spruebush (浇口套)A板 Aplate (定模板)B板 Bplate（动模板）方铁 spacer block (垫铁)底板 bottom clamp plate(动模底板)面板 top clamp plate(定模底板)顶针 ejector pin（顶杆）直边钉 guide pin (导柱)托司 shoulder guide bush(导套)直司 straight guide bush(导柱)回针 returnpin(回程杆)细水口边钉 support pin(副导柱)蓝弹簧 blue spring（回程弹簧）水口推板 runner stripper plate(卸流道板)中边钉 ejector guide pin (顶板导柱)顶针板 ejector retainer plate(顶杆固定板)顶针底板 ejectorplate(顶杆垫板)撑头 support pollar（支撑柱）垃圾钉 stop pin (限位钉)呵 core (后模肉内镶件)后模肉 back mold body(后模镶件)前模肉 cavity（前模镶件）扣鸡 P-lock。
专业英语注塑成型专业词汇
专业英语---注塑成型专业词汇Injection machine 啤机Shot size<weight）实际射胶量 injection volume 理论射胶量 min mold height 最小容模厚度b5E2RGbCAPMax mold height 最大容模厚度 Tie bar clearance 拉杆间距Die plate size 模板尺寸p1EanqFDPwEjector stroke 顶出行程 barrel 炮筒,机筒 clamp force 锁模力 non-return valve 止回阀DXDiTa9E3dshear 剪切 opening 开模行程Injection pressure 射胶压力 back pressure 背压RTCrpUDGiTnozzle size 射咀尺寸Cycle time 循环周期 down time 停机时间hopper 料筒Mold release 脱模剂 lubrication 润滑 workhorse 主力,主要设备5PCzVD7HxAReserve pressure/packing pressure保压 mold trial 试模 shot<一）啤jLBHrnAILgDecompress 减压 oven 烤炉,烘灶 shrinkage rate 收缩率Residence time 滞留时间xHAQX74J0Xinjection speed 注射速度 booster time 增压时间Compression ratio 压缩比LDAYtRyKfEmold close time 合模时间Resin 胶料Plastification 塑化,增塑 viscosity 粘性,粘度contamination 污染,杂物Zzz6ZB2Ltk Thermoplastic 热塑性塑料 thermosetting plastics 热固性塑料Booster time 增压时间dvzfvkwMI1feed 喂料,填充 purge 净化Flame retardant 阻燃degradation 降解,软化rqyn14ZNXIregrind 再粉碎Water absorption 吸水 reinforce 增强,加固specific gravity 比重EmxvxOtOcoElongation 延伸率 density 密度 melting point 熔点Polystyrene 聚苯乙烯<PS）SixE2yXPq5Styrene 苯乙烯 Acrylonitrile 丙烯腈Polypropylene 聚丙烯<PP） Polyethylene 聚乙烯6ewMyirQFLglass fiber 玻纤Condensation 凝固,浓缩 crystalline resin结晶形塑料kavU42VRUsMold materials 模具General-purpose steel 多用途钢 tool steel 模具钢Free-cutting steel 高速切削钢y6v3ALoS89case hardening steel 表面硬化钢 Pre-hardened steel 预硬钢ball and roller bearing steel 滚珠轴承钢M2ub6vSTnP Nonferrous steel 非铁合金 high speed steel 高速钢 cast iron 铸铁Steel specification 钢材规格0YujCfmUCwsteel certification 钢材合格证明书Stainless steel 不锈钢nickel 镍 chrome 铬 aluminum 铝Copper 铜brass 黄铜 bronze 青铜 titanium 钛eUts8ZQVRdProcessing 钢材地加工方法Harding / quench 淬火 nitride 氮化 temper 回火 anneal 退火Roll 轧制 abrasive 研磨,磨损地sQsAEJkW5Tfinish 精加工,抛光<polish）Case-hardening 表面硬化milling machine 铣<锣）床GMsIasNXkALathe车床 drill 钻床 wire cut 线割 NC(numericalcontrol > 数控材料TIrRGchYzgEDM (Electrical discharge machine> 电火花加工 Cut steel 开料Precision ground 精密研磨7EqZcWLZNX heat treatment 热处理 tap 丝锥,攻牙Texture 蚀纹weld 焊接 forge 锻压 deformation 变形lzq7IGf02ESpraying 喷涂 die-cast 压铸Properties 性能Resistance 电阻,抵抗能力 abrasion / wear磨损 erode / corrode 腐蚀Toughness 韧性zvpgeqJ1hkyield strength 屈服强度 tensile strength 拉伸强度Fatigue strength 疲劳强度 break 断裂NrpoJac3v1 stress 应力 hardness 硬度Humidity / moisture 潮湿,湿气roughness 粗糙度 parameter 参数1nowfTG4KIThermal conductivity 导热系数 manufacture 制造,加工drawback 缺点 Ductility 延展性fjnFLDa5Zo grain 晶粒 property 性能,财产 brittleness 脆性GD&T <Geometric Dimensions and Tolerance ）形位尺寸公差Flexural strength 挠曲强度tfnNhnE6e5impact 冲击 conductivity 传导性,导电性Optical 光学地transparent 透明地 insulation 绝缘HbmVN777sL Mechanical 机械地 processability 可加工性能 timeyield 蠕变 Physical 物理地 flow rate 流动速率V7l4jRB8Hscompressive strength 压缩强度Adhesive 粘附地,胶合durability 耐用性83lcPA59W9Mold design 模具设计Tooling specification 模具规格 mould flow 流动模拟sprue nozzle 唧咀孔Clearance 避空,间隙mZkklkzaaP undercut 倒扣 flush 插入,埋入 legend 图例Groove 凹槽latch 插销 class 类型,种类 plan 平面图AVktR43bpw Orifice 孔,口 column 柱位 boss 凸台 standard 标准,规格Rib 骨位 tapered interlock 锥形管位块ORjBnOwcEd Bubbler 炮隆Bolt 螺钉,销顶 identification mark 铭牌P/L strip 锁模片2MiJTy0dTTOverflow well / cold-slug well 冷料井 Vent 排气 pocket 槽Gate location 入水点 full line 实线gIiSpiue7Abroken line 虚线Retainer 固定,支撑 operator 操作者<啤工） receptacle 插座uEh0U1YfmhLifting hole 吊令孔 insulation plate 隔热板 cavity number 型腔号Bolster 支撑,垫子IAg9qLsgBXvent channel 排气槽 leak / filter 渗漏Leak test 试运水 stamp / engrave 雕刻,印记<打字唛）WwghWvVhPE Clamp slot 码模槽 support button / pin 垃圾钉 cut steel 开料Lodge 安装,放置asfpsfpi4kinlay 镶嵌,插入 cam / lifter 斜顶Stripper推方lifting bar 吊模方 sprue 唧咀ooeyYZTjj1 tolerance 公差Counter bore 沉孔 slant 倾斜,斜面conical 圆锥地,圆锥形地BkeGuInkxIBolt 螺栓 manifold 热流道板 prototype tooling 原型实验Gusset 角撑PgdO0sRlMoreverse mold 倒装模 constrain / restrict约束,限制Counter lock 反锁3cdXwckm15thermocouple 热电偶 moldmaker 模具制造商Asset / propertynumber 资产编号h8c52WOngMtool product destination 模具生产地点 Accelerating ejection加速顶出v4bdyGioushydraulic 液压地 pneumatic 气动地Trapezoid 梯形地semi-round 半圆形 format 格式J0bm4qMpJ9baffle 隔水片Electrode 电极,铜公 spare part 配件gall 磨伤,插伤Cable 电缆,电线XVauA9grYP plating / coating <电）镀 bonding / joint 接头Walltransition 壁厚过渡bR9C6TJscwProduct problem 产品问题Troubleshoot 故障处理 reduce(add> plastic 减<加）胶Burr/flash披峰 Burn mark 烧焦pN9LBDdtrdejector mark 顶针印,顶白 black specs 黑点,黑斑Discoloration 混色,污点 gloss 光泽DJ8T7nHuGT jetting/worming 走水纹Sink mark 缩水 void / bubble 气泡,夹气 distortion 变形QF81D7bvUAWarpage 翘曲 short molding / non-fill缺胶,未走齐 Weld line / knit line 夹水线4B7a9QFw9hdiscarded as useless 报废 Split line 夹线 stick in sprue bushing / cavity / core 粘唧咀/前模/后模ix6iFA8xoX Break / crack 顶裂 brittleness 脆性,易脆Others 其他Invoice 发票,清单 vendor(er> 卖方 vendee 买方guideline 方针,指导Intricate 复杂地wt6qbkCyDEconfidential 机密地,不可外泄地 proprietary 私有地Authorize 批准,授权 recipient 接收者Kp5zH46zRkissue ①发布,提供；②问题Approve 确认,赞成requirement 需要,必需物 const 常数,常量Yl4HdOAA61 Regarding 关于,涉及 opposite 相反地,对面地 latitude 纬度,纵向地Version 版本ch4PJx4BlIdefinition 注释,解说 transversal 横向地,截线Profile 轮廓,剖面 eliminate / cancel 取消qd3YfhxCzoallow / permit 允许,许可Respective 各自地,分别地individual 单独地 decrease 减少E836L11DO5increase 增加Preliminary 初步地 approximately 大约,近似estimate / valuate估计,预算S42ehLvE3MAdjust 调整,校准 application 应用,申请 maintain 维持Accurate / precise 精确地501nNvZFissmooth 光滑,顺畅地 device 装置,设备Convenient 方便地deadline 截至日期jW1viftGw9available 有用地,有空地Shift 轮班,换班 critical 关键地,临界地 exceptional 异常地,优异地xS0DOYWHLPExceed 超过 layout 布局,方案 loss 损失,消耗 install 安装,安置 Rotation 旋转LOZMkIqI0witem 条款,工程 quotation 报价 stabilize 稳定Quality 质量 quantity 数量 couple 连接,接合ZKZUQsUJed configuration 构造,外形Illustrate 图解说明 simulation 模拟,仿真recommend 推荐使用dGY2mcoKtT。
注塑专业英语
Surface Appearance外观Glossiness/gloss finish光洁度Matt finish/matt surface毛面Glass fiber rich surface/glass emergence on the surface 玻纤外露Blooming/surface blooming表面析出White patches on surface表面白斑Silver marks/silver streak银纹Splay mark水纹Flow mark流纹Weld line溶结纹Brittle/brittleness脆Bubbles/trapped gas气泡V oid孔Burn marks烧伤FR failed阻燃不合格Flame rating V-2阻燃V-2Poor dispersion分散不好FR/PTFE …agglomerates etc阻燃剂/PTFE…结块Pellet porous粒子不密/蜜蜂窝Low impact/tensile etc物理性能低High flow/filler content etc流动性/填充…过高Longs/fines/doubles长粒/碎屑/连粒Poor cut粒形不好Bristle/voids表面有小气泡/孔Glass bundles玻纤结团Product was rejected due to产品不能接受因为…High moisture level高水分Warpage/warped翘曲Shrinkage/shrink收缩Sink marks缩影Short shot/short molding打不满Distortion变形Over dimension尺寸过大Under dimension尺寸过小Flashing飞边Discoloration变色Off color颜色差异Flow rate流动率Viscous粘High flow高流动Low flow低流动Sticky粘Mold release脱模Antioxidant抗氧剂Flame retardant agent阻燃剂Heat stabilizer热稳定剂Chopped glass fiber短切玻纤Roving glass fiber粗纱/长玻纤Glass beads玻璃微珠Milled fiber碾磨纤Molybdenum disulfide/moly/MoS2 二硫化钼Colorant着色剂Pigment颜料Dye染料Accepted product specification接受产品规格Approved our product认可我们的产品Re-set spec重新定标准Add in extra …添加多一点…Reduced … content减少…含量Dr opped/reduced … by x％减少…含量…％Confirmed color standard确认颜色标准Approved color standard认可颜色标准Re-confirmed color standard重新确认颜色标准Qualified our product认可我们的产品Undergoing heat aging test在做热老化实验Product is under testing产品在测试当中Received first order接了第一个定单Expected to finish by …预计在…完成Expected order is xMT预计定单量…吨Estimated annual/monthly consumption 预计年/月用量air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁)cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模？die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧？goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶冲头headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块master plate 靠模样板match plate 分型板mold base 塑胶模座mold clamp 铸模紧固夹mold platen 模用板moving bolster 换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paring line 分模线parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pilot pin 导pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 托料板return pin 回位梢riding stripper 浮动脱模器ring gate 环型浇口？roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide(slide core) 滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架spindle 主轴sprue 注道sprue bushing 注道衬套sprue bushing guide 注道导套sprue lock bushing 注道定位衬套sprue puller 注道拉料spue line 合模线square key 方键square nut 方螺帽square thread 方螺纹stop collar 限位套stop pin 止动梢stop ring 止动环stopper 定位停止梢straight pin 圆柱stripper bolt 脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱support pin 支撑梢supporting plate 托板sweep templete 造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝模板plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印extension dwg展开图procedure dwg工程图die structure dwg结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量三、模具塑料模具mould of plastics 注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plate Top plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板support plate方铁spacer plate 底针板ejector plate面针板ejector retainer plate回针Return pin导柱Guide pin有托导套Shoulder Guide bush直导套Straight Guide bush动模座板Bottom clamp plate Moving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould 动模movable mould, movable half上模upper mould，upper half下模lower mould，lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具three plate mould脱模ejection换模腔模具interchangeable cavity mould脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine一、组织机构及职位二、X X电子有限公司XX Electronics CO., Ltd三、总经理办公室General manager’s office四、企管部Enterprise management department (EM)五、行政部Administration department (AD)六、销售部Sales department (SD)七、财务部Financial department (FD)八、技术部Technology department (TD)九、物控部Production material control department(PMC)十、生产部Production department(PD)十一、模具部Mold manufacturing department, Tooling manufacturing department (TM)十二、品管部Quality Assurance department (QA) 十三、冲压车间Stamp workshop, press workshop 十四、注塑车间injection workshop十五、装配车间Assembly workshop十六、模具装配车间Mold and die Assembly workshop 十七、金属加工车间metal machine workshop十八、电脉冲车间Electric discharge process workshop十九、线切割车间wire cutting process workshop 二十、工磨车间Grinding workshop二十一、总经理General manager (GM)二十二、副总经理Vice-general manager二十三、经理manager二十四、董事长president二十五、副董事长Vice-president二十六、XX部门经理Manager of XX department二十七、主任、主管supervisor二十八、拉长Line leader二十九、组长Foreman, forelady三十、秘书secretary三十一、文员clerk三十二、操作员operator三十三、助理assistant六．物控保质期shelf lifeABC分类法ABC Classification反常需求Abnormal Demand措施信息Action Message活动报告标志Action-report-flag基于活动的成本核算Activity-based Costing (ABC) 实际能力Actual Capacity实际成本Actual Costs调整现有库存量Adjust-on-hand已分配量Allocation替代工序Alternative Routine装配订单Assembly Order装配零件表Assembly Parts List装配Assembly计划自动重排Automatic Rescheduling可达到库存Available Inventory可用材料Available Material达到库存Available Stock可利用工时Available Work可签约量Available-to-promise平均库存Average Inventory欠交订单Back Order倒序计划Back Scheduling倒冲法Back flush未完成订单Backlog现有库存余额Balance-on-hand Inventory批号Batch Number批量生产Batch Production标杆瞄准Benchmarking工时清单Bill of Labor提货单Bill of Lading物料清单Bill of Material分库Branch Warehouse经营规划Business Plan采购员Buyer能力管理Capacity Management能力需求计划Capacity Requirements Planning (CRP) 保管费率Carrying Cost Rate保管费Carrying Cost单元式制造Cellular Manufacturing修改批量日期Change Lot Date修改工序Change Route修改产品结构Change Structure检查点Check Point闭环物料需求计划Closed Loop MRP通用工序标识Common Route ID计算机集成制造Computer-integrated Manufacturing (CIM)配置代码Configuration Code约束管理/约束理论Constraints Management/Theory of Constraints (TOC)依成本的材料清单Costed Bill of Material急需零件Critical Part累计提前期Cumulative Lead Time现有运转时间Current Run Hour现有运转数量Current Run Quantity周期盘点Cycle Counting调整日期Date Adjust有效日期Date Available修改日期Date Changed结束日期Date Closed截止日期Date Due生产日期Date in Produced库存调整日期Date Inventory Adjust作废日期D ate Obsolete收到日期Date Received交付日期Date Released需求日期Date Required发货日期Date to Pull空负荷Dead Load需求管理Demand Management需求Demand实际能力Demonstrated Capacity非独立需求Dependent Demand直接增减库存处理法Direct-deduct Inventory Transaction Processing发料单Disbursement List派工单Dispatch List分销资源计划Distribution Resource Planning (DRP) 鼓－缓冲－绳子Drum-buffer-rope经济订货批量Economic Order Quantity (EOQ)工程变更生效日期Engineering Change Effect Date工程变更生效单Engineering Change Effect Work Order工程停止日期Engineering Stop Date例外控制Exception Control呆滞材料分析Excess Material Analysis急送代码Expedite Code加工订单Fabrication Order补足欠交Fill Backorder总装提前期Final Assembly Lead Time 确认的计划订单Firm Planned Order固定订货批量F ixed Order Quantity集中预测Focus Forecasting完全跟踪Full Pegging通用生产管理原则Generally Accepted Manufacturing Practices毛需求Gross Requirements在制品库存In Process Inventory独立需求Independent Demand投入/产出控制Input/ Output Control检验标识Inspection ID厂际需求Interplant Demand库存周转率Inventory Carry Rate仓库库位类型Inventory Location Type库存周转次数Inventory Turnover发送订单Issue Order项目记录Item Record物料项目Item加工车间Job Shop准时制生产Just-in-time (JIT)看板Kanban人工工时Labor Hour最后运输日期Last Shipment Date提前期Lead Time层Level负荷量Load Leveling负荷报告Load Report负荷Load仓位代码Location Code仓位备注Location Remarks仓位状况Location Status按需订货Lot for Lot批量标识Lot ID批量编号Lot Number批量Lot Size低位码Low Level Code机器能力Machine Capacity机器加载Machine Loading外购或自制决策Make or Buy Decision面向订单生产的产品Make-to-order Product面向库存生产的产品Make-to-stock Product制造周期时间Manufacturing Cycle Time制造资源计划Manufacturing Resource Planning (MRP II)主生产计划Master Production Schedule (MPS)物料成本Material Cost物料发送和接收Material Issues and Receipts物料需求计划Material Requirements Planning (MRP) 登陆标志MPS Book Flag MPS多重仓位Multiple Location净改变式MRP N et Change MRP净需求Net Requirements新仓位New Location新组件New Parent新仓库New Warehouse不活动报告No Action Report现有库存量On-hand Balance未结订单Open Order订单输入Order Entry订货点Order Point订货方针Order Policy订货承诺Order Promising订货备注Order Remarks双亲Parent零件清单Part Bills零件批次Part Lot零件编号Part Number零件Part反查Pegging领料单Picking List领料/提货Picking计划订单Planned Order后减库存处理法Post-deduct Inventory Transaction Processing前减库存处理法Pre-deduct Inventory Transaction Processing发票价格Price Invoice采购订单价格Price Purchase Order优先计划Priority Planning产品控制Product Control产品线Production Line生产规划编制Production Planning产品率Production Rate产品结构树Production Tree预计可用库存Projected Available Balance采购订单跟踪Purchase Order Tracking已分配量Quantity Allocation仓位数量Quantity At Location欠交数量Quantity Backorder完成数量Quantity Completion需求量Quantity Demand毛需求量Quantity Gross进货数量Quantity In排队时间Queue Time队列Queue重生成式MRP Regenerated MRP重排假设Rescheduling Assumption资源需求计划Resource Requirements Planning粗能力计划Rough-cut Capacity Planning工艺路线Routing安全库存量Safety Stock保险期Safety Time预计入库量Scheduled Receipt残料率Scrap Factor发送零件Send Part维修件Service Parts发货地址Ship Address发货单联系人Ship Contact发货零件Ship Date发货单Ship Order 工厂日历Shop Calendar车间作业管理Shop Floor Control损耗系数Shrinkage Factor标准产品成本Standard Product Cost标准机器设置工时Standard Set Up Hour标准单位运转工时Standard Unit Run Hour标准工资率Standard Wage Rate状况代码Status Code库存控制Stores Control建议工作单Suggested Work Order约束理论Theory of Constraints (TOC)时间段Time Bucket时界Time Fence单位成本Unit Cost采购计划员Vendor Scheduler采购计划法Vendor Scheduling工作中心能力Work Center Capacity工作中心Work Center在制品Work in Process工作令跟踪Work Order Tracking工作令Work Order工作进度安排Work Scheduling零库存Zero Inventories经济订货批量＝Squat(2*年订货量*平均一次订货准备所发生成本/每件存货的年储存成本)美国生产和库存控制协会APICS，American Production & Inventory Control Society三十四、产品三十五、连接器connector三十六、端子terminal三十七、条型连接器bar connector三十八、阴连接器Housing三十九、阳连接器wafer四十、线束wire harness四十一、间距space四十二、额定电压rated voltage四十三、额定电流rated current四十四、接触电阻contact resistance四十五、绝缘电阻insulation resistance四十六、超声波焊接ultrasonic welding四十七、耐压withstand voltage四十八、针pin四十九、物料编号part number五十、导线wire五十一、基体金属Base metal五十二、电缆夹cable clamp五十三、倒角chamfer五十四、接触面积contact area五十五、接触件安装孔contact cavity五十六、接触长度contact length五十七、接触件电镀层contact plating五十八、接触压力contact pressure五十九、接触件中心距contact space六十、接触簧片contact spring六十一、插孔socket contact六十二、法兰、凸缘Flange六十三、界面间隙interfacial gap六十四、键Key六十五、键槽keyway六十六、过渡段ramp六十七、屏蔽套shielding六十八、定位基准Datum reference六十九、扁平电缆flat cable ，Ribbon cable七十、柔性印刷电线Flexible printed wiring七十一、多层印制电路Multilayer printed circuit七十二、焊盘pad七十三、图形pattern七十四、间距pitch七十五、负极Negative pole七十六、正极positive pole七十七、回流Reflow七十八、原理图Schematic diagram七十九、单面板single sided board八十、双面板Two-sided board，Double-sided board 八十一、表面安装surface Mounting八十二、翘曲warp，bow八十三、波峰焊wave soldering八十四、编织层braid八十五、同轴电缆coaxial cable八十六、电介质dielectric八十七、电缆中导线的头数ends八十八、外部干扰external interference八十九、填充物filler九十、护套jacket九十一、比重specific gravity九十二、电阻的温度系数Temperature coefficient of resistance九十三、品管九十四、SPC statistic process control九十五、品管保证Quality Assurance九十六、品管控制Quality control九十七、来料检验IQC Incoming quality control九十八、巡检IPQC In-process quality control九十九、校对calibration百、动态试验dynamic test百一、环境试验Environmental test百二、非破坏性试验non-destructive test百三、光泽gloss百四、击穿电压(dielectric) breakdown voltage百五、拉伸强度tensile strength百六、冷热骤变试验thermal shock test百七、环境试验炉Environmental chamber百八、盐雾实验salt spray test百九、绝缘电阻测试验仪Insulating resistance meter百十、内应力internal stress百十一、疲劳fatigue百十二、蠕变creep百十三、试样specimen百十四、撕裂强度tear strength 百十五、缩痕shrink mark, sink mark百十六、耐久性durability百十七、抽样sampling百十八、样品数量sample size百十九、AQL Acceptable Quality level百二十、批量lot size百二十一、抽样计划sampling plan百二十二、OC曲线operation curve百二十三、试验顺序sequence of tests百二十四、环境温度ambient temperature百二十五、可焊性solderability百二十六、阻燃性flame resistance百二十七、生产百二十八、注塑机injection machine百二十九、冲床Punch machine百三十、混料机blender mixer百三十一、尼龙nylon百三十二、黄铜brass百三十三、青铜bronze百三十四、紫(纯)铜copper百三十五、料斗hopper百三十六、麻点pit百三十七、配料compounding百三十八、涂层coating百三十九、飞边flash百四十、预热preheating百四十一、料reworked material百四十二、塑料reworked plastics百四十三、工艺设计process design百四十四、紧急停止emergency stop百四十五、延时time delay七．QS-9000中的术语APQP Advanced Product Quality Planning and Control Plan，产品先期策划和控制计划PPAP Production Part Approval Process,生产件批准程序FMEA Potential Failure Mode and Effects Analysis,潜在失效模式及后果分析Injection machine 啤机Shot size（weight）实际射胶量injection volume 理论射胶量min mold height 最小容模厚度Max mold height 最大容模厚度Tie bar clearance 拉杆间距Die plate size 模板尺寸Ejector stroke 顶出行程barrel 炮筒，机筒clamp force 锁模力non-return valve 止回阀shear 剪切opening 开模行程Injection pressure 射胶压力back pressure 背压nozzle size 射咀尺寸Cycle time 循环周期down time 停机时间hopper 料筒Mold release 脱模剂lubrication 润滑work horse 主力，主要设备Reserve pressure/packing pressure保压mold trial 试模shot （一）啤Decompress 减压oven 烤炉，烘灶shrinkage rate 收缩率Residence time 滞留时间injection speed 注射速度booster time 增压时间Compression ratio 压缩比mold close time 合模时间Resin 胶料Plastification 塑化，增塑viscosity 粘性，粘度contamination 污染，杂物Thermoplastic 热塑性塑料thermosetting plastics 热固性塑料Booster time 增压时间feed 喂料，填充purge 净化Flame retardant 阻燃degradation 降解，软化regrind 再粉碎Water absorption 吸水reinforce 增强，加固specific gravity 比重Elongation 延伸率density 密度melting point 熔点Polystyrene 聚苯乙烯（PS）Styrene 苯乙烯Acrylonitrile 丙烯腈Polypropylene 聚丙烯（PP）Polyethylene 聚乙烯glass fiber 玻纤Condensation 凝固，浓缩crystalline resin 结晶形塑料Mold materials 模具General-purpose steel 多用途钢tool steel 模具钢Free-cutting steel 高速切削钢case hardening steel 表面硬化钢Pre-hardened steel 预硬钢ball and roller bearing steel 滚珠轴承钢Nonferrous steel 非铁合金high speed steel 高速钢cast iron 铸铁Steel specification 钢材规格steel certification 钢材合格证明书Stainless steel 不锈钢nickel 镍chrome 铬aluminum 铝Copper 铜brass 黄铜bronze 青铜titanium 钛Processing 钢材的加工方法Harding / quench 淬火nitride 氮化temper 回火anneal 退火Roll 轧制abrasive 研磨，磨损的finish 精加工，抛光（polish）Case-hardening 表面硬化milling machine 铣（锣）床Lathe车床drill 钻床wire cut 线割NC(numerical control ) 数控材料EDM (Electrical discharge machine) 电火花加工Cut steel 开料Precision ground 精密研磨heat treatment 热处理tap 丝锥，攻牙Texture 蚀纹weld 焊接forge 锻压deformation 变形Spraying 喷涂die-cast 压铸Properties 性能Resistance 电阻，抵抗能力abrasion / wear磨损erode / corrode 腐蚀Toughness 韧性yield strength 屈服强度tensile strength 拉伸强度Fatigue strength 疲劳强度break 断裂stress 应力hardness 硬度Humidity / moisture 潮湿，湿气roughness 粗糙度parameter 参数Thermal conductivity 导热系数manufacture 制造，加工drawback 缺点Ductility 延展性grain 晶粒property 性能，财产brittleness 脆性GD&T （Geometric Dimensions and Tolerance ）形位尺寸公差Flexural strength 挠曲强度impact 冲击conductivity 传导性，导电性Optical 光学的transparent 透明的insulation 绝缘Mechanical 机械的processability 可加工性能timeyield 蠕变Physical 物理的flow rate 流动速率compressive strength 压缩强度Adhesive 粘附的，胶合durability 耐用性Mold design 模具设计Tooling specification 模具规格mould flow 流动模拟sprue nozzle 唧咀孔Clearance 避空，间隙undercut 倒扣flush 插入，埋入legend 图例Groove 凹槽latch 插销class 类型，种类plan 平面图Orifice 孔，口column 柱位boss 凸台standard 标准，规格Rib 骨位tapered interlock 锥形管位块Bubbler 炮隆Bolt 螺钉，销顶identification mark 铭牌P/L strip 锁模片Overflow well / cold-slug well 冷料井Vent 排气pocket 槽Gate location 入水点full line 实线broken line 虚线Retainer 固定，支撑operator 操作者（啤工）receptacle 插座Lifting hole 吊令孔insulation plate 隔热板cavity number 型腔号Bolster 支撑，垫子vent channel 排气槽leak / filter 渗漏Leak test 试运水stamp / engrave 雕刻，印记（打字唛）Clamp slot 码模槽support button / pin 垃圾钉cut steel 开料Lodge 安装，放置inlay 镶嵌，插入cam / lifter 斜顶Stripper推方lifting bar 吊模方sprue 唧咀tolerance 公差Counter bore 沉孔slant 倾斜，斜面conical 圆锥的，圆锥形的Bolt 螺栓manifold 热流道板prototype tooling 原型试验Gusset 角撑reverse mold 倒装模constrain / restrict约束，限制Counter lock 反锁thermocouple 热电偶moldmaker 模具制造商Asset / property number 资产编号tool product destination 模具生产地点Accelerating ejection 加速顶出hydraulic 液压的pneumatic 气动的Trapezoid 梯形的semi-round 半圆形format 格式baffle 隔水片Electrode 电极，铜公spare part 配件gall 磨伤，插伤Cable 电缆，电线plating / coating （电）镀bonding / joint 接头Wall transition 壁厚过渡Product problem 产品问题Troubleshoot 故障处理reduce(add) plastic 减（加）胶Burr/flash披峰Burn mark 烧焦ejector mark 顶针印，顶白black specs 黑点，黑斑Discoloration 混色，污点gloss 光泽jetting/worming 走水纹Sink mark 缩水void / bubble 气泡，夹气distortion 变形Warpage 翘曲short molding / non-fill缺胶，未走齐Weld line / knit line 夹水线discarded as useless 报废Split line 夹线stick in sprue bushing / cavity / core 粘唧咀/前模/后模Break / crack 顶裂brittleness 脆性，易脆Others 其他Invoice 发票，清单vendor(er) 卖方vendee 买方guideline 方针，指导Intricate 复杂的confidential 机密的，不可外泄的proprietary 私有的Authorize 批准，授权recipient 接收者issue ①发布，提供；②问题Approve 确认，赞成requirement 需要，必需物const 常数，常量Regarding 关于，涉及opposite 相反的，对面的latitude 纬度，纵向的Version 版本definition 注释，解说transversal 横向的，截线Profile 轮廓，剖面eliminate / cancel 取消allow / permit 允许，许可Respective 各自的，分别的individual 单独的decrease 减少increase 增加Preliminary 初步的approximately 大约，近似estimate / valuate估计，预算Adjust 调整，校准application 应用，申请maintain 维持Accurate / precise 精确的smooth 光滑，顺畅的device 装置，设备Convenient 方便的deadline 截至日期available 有用的，有空的Shift 轮班，换班critical 关键的，临界的exceptional 异常的，优异的Exceed 超过layout 布局，方案loss 损失，消耗install 安装，安置Rotation 旋转item 条款，项目quotation 报价stabilize 稳定Quality 质量quantity 数量couple 连接，接合configuration 构造，外形Illustrate 图解说明simulation 模拟，仿真recommend 推荐使用。
注塑英语
塑件&模具英语词汇编辑: 时间:2006-3-3 13:21:11compre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模taper 锥拔leather cloak 仿皮革shiver 饰纹flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝striper plate 脱料板piston 活塞cylinder 汽缸套chip 细碎物handle mold 手持式模具（移转成型用模具）encapsulation molding 低压封装成型（射出成型用模具）two plate 两极式（模具）well type 蓄料井insulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块valve gate 阀门浇口band heater 环带状的电热器spindle 阀针spear head 刨尖头slag well 冷料井cold slag 冷料渣air vent 排气道welding line 熔合痕eject pin 顶出针knock pin 顶出销return pin 回位销反顶针sleave 套筒stripper plate 脱料板insert core 放置入子runner stripper plate 浇道脱料板guide pin 导销eject rod (bar)（成型机）顶业捧subzero 深冷处理three plate 三极式模具runner system 浇道系统stress crack 应力电裂orientation 定向sprue gate 射料浇口，直浇口nozzle 射嘴sprue lock pin 料头钩销(拉料杆)slag well 冷料井side gate 侧浇口edge gate 侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口fan gate 扇形浇口dish gate 因盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口subarine gate 潜入式浇口tunnel gate 隧道式浇口pin gate 针点浇口Runner less 无浇道(sprue less) 无射料管方式long nozzle 延长喷嘴方式sprue 浇口;溶渣一些注塑用语英汉对照可能你用的着Surface Appearance 外观Glossiness/gloss finish 光洁度Matt finish/matt surface 毛面Glass fiber rich surface/glass emergence on the surface 玻纤外露Blooming/surface blooming 表面析出White patches on surface 表面白斑Silver marks/silver streak 银纹Splay mark 水纹Flow mark 流纹Weld line 溶结纹Brittle/brittleness 脆Bubbles/trapped gas 气泡V oid 孔Burn marks 烧伤FR failed 阻燃不合格Flame rating V-2 阻燃V-2Poor dispersion 分散不好FR/PTFE …agglomerates etc 阻燃剂/PTFE…结块Pellet porous 粒子不密/蜜蜂窝Low impact/tensile etc 物理性能低High flow/filler content etc 流动性/填充…过高Longs/fines/doubles 长粒/碎屑/连粒Poor cut 粒形不好Bristle/voids 表面有小气泡/孔Glass bundles 玻纤结团Product was rejected due to 产品不能接受因为…High moisture level 高水分Warpage/warped 翘曲Shrinkage/shrink 收缩Sink marks 缩影Short shot/short molding 打不满Distortion 变形Over dimension 尺寸过大Under dimension 尺寸过小Flashing 飞边Discoloration 变色Off color 颜色差异Flow rate 流动率Viscous 粘High flow 高流动Low flow 低流动Sticky 粘Mold release 脱模Antioxidant 抗氧剂Flame retardant agent 阻燃剂Heat stabilizer 热稳定剂Chopped glass fiber 短切玻纤Roving glass fiber 粗纱/长玻纤Glass beads 玻璃微珠Milled fiber 碾磨纤Molybdenum disulfide/moly/MoS2 二硫化钼Colorant 着色剂Pigment 颜料Dye 染料Accepted product specification 接受产品规格Approved our product 认可我们的产品Re-set spec 重新定标准Add in extra … 添加多一点…Reduced … content 减少…含量Droppe d/reduced … by x％减少…含量…％Confirmed color standard 确认颜色标准Approved color standard 认可颜色标准Re-confirmed color standard 重新确认颜色标准Qualified our product 认可我们的产品Undergoing heat aging test 在做热老化实验Product is under testing 产品在测试当中Received first order 接了第一个定单Expected to finish by … 预计在…完成Expected order is xMT 预计定单量…吨Estimated annual/monthly consumption 预计年/月用量1bar=0.1Mpa=14.5psi压力换算压力1巴（bar）=105帕（Pa）1达因/厘米2（dyn/cm2）=0.1帕（Pa）1托（Torr）=133.322帕（Pa）1毫米汞柱（mmHg）=133.322帕（Pa）1毫米水柱（mmH2O）=9.80665帕（Pa）1工程大气压=98.0665千帕（kPa）1千帕（kPa）=0.145磅力/英寸2（psi）=0.0102千克力/厘米2（kgf/cm2）=0.0098大气压（atm）1磅力/英寸2（psi）=6.895千帕（kPa）=0.0703千克力/厘米2（kg/cm2）=0.0689巴（bar）=0.068大气压（atm）1物理大气压（atm）=101.325千帕（kPa）=14.696磅/英寸2（psi）=1.0333巴（bar）。
注塑常用术语英文表达
1.雾气Moisture Streaks2.玻纤分配不均Glass Fiber Streaks3.困气Gas Trap Effect4.银丝纹Sliver Marks5.结合线Weld Line6.水波痕Water Wave Effect7.黑点Dark Sport8.顶出印Visible Ejector Marks9.变形Deformation During Demolding10.填充不足Short Filling11.冷料流痕Cold Slug12.进胶口点不良Dull Spots Near The Sprue13.喷射痕Jetting14.表面起层Flaking Of The Surface Layer15.浮泡Entrapped Air16.过热变色Burnt Streaks17.龟裂Stress Crack18.缩水痕Sink Marks19.真空气泡Density Bubble20.披锋Flash21.擦伤印Scratch MarksGlass fiber rich surface/glass emergence on the surface22 尺寸过大Over dimension23尺寸过小Under dimension24 翘曲Warpage/warped25 收缩Shrinkage/shrink26 缩影Sink marks27 打不满Short shot/short molding塑料模具mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plate Top plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板support plate方铁spacer plate底针板ejector plate面针板ejector retainer plate回针Return pin导柱Guide pin有托导套Shoulder Guide bush 直导套Straight Guide bush动模座板Bottom clamp plate Moving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate 凸模固定板punch-retainer plate 顶针ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould动模movable mould, movable half上模upper mould，upper half下模lower mould，lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具three plate mould脱模ejection换模腔模具interchangeable cavity mould 脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine（注：文档可能无法思考全面，请浏览后下载，供参考。
注塑方面英语术语
注塑方面英语术语压铸die-cast压炼injection铸件casting/cast/founding起泡/气泡bubble/blister/air bubble缺料shor-shots/undershot浇不足/*铸under-founding多料superfluities/superfluous material(alloy)顶针痕ejector (pins) mark花纹flow mark/flow line冷纹cold mark/cold streak油纹oil streak走水纹splash mark银纹silver streaks霜纹splay mark夹水纹silver streaks/flow line/weld line 扣模/粘模sprue sticking砂眼/气眼air hole（塑胶件）弯曲/变形warping/warpage变形deformation扭曲twist翅曲warp/warped材料错误using wrong plastic material 凸痕convex mark凹位/凹陷sink mark/dent mark披锋flashing批损pare-mark/cut mark批凹pare off锉纹trim-mark/file-mark锉损excessive trim mark黑点/黑纹black spots/black streak发白white mark烧焦burn marks刮花/刮痕scratch mark擦痕/擦伤rub-mark/brush-burn裂缝cracking裂纹craking line碰损stress mark起皮chip错位（合模线）part line misaling ment孔位尺寸改变dimension various哑色dull color表面变光滑（喷油面）glossy finishing表面sruface/outside镶件insert/insert word缩水/收缩sink mark/shrinkage/shrink mark 偏差color deviation色粉colourment颜色colour/color零件污糟dirty mark on part顶白stress mark/ejector mark屈曲bent夹模线移位part line misalignment胶件料厚不均uneven wall thickness水口料degraded material凹印sink mark擦花abrasion mark混色contamination mark热点不良poor heat sticking定位圈locating ring唧嘴sprue bush (浇口套)A板 A plate (定模板)B板 B plate（动模板）方铁spacer block (垫铁)底板bottom clamp plate(动模底板)面板top clamp plate(定模底板)顶针ejector pin（顶杆）直边钉guide pin (导柱)托司shoulder guide bush(导套)直司straight guide bush(导柱)回针return pin(回程杆)细水口边钉support pin(副导柱)蓝弹簧blue spring（回程弹簧）水口推板runner stripper plate(卸流道板)中边钉ejector guide pin (顶板导柱)顶针板ejector retainer plate(顶杆固定板)顶针底板ejector plate(顶杆垫板)撑头support pollar（支撑柱）垃圾钉stop pin (限位钉)呵core (后模肉内镶件)后模肉back mold body(后模镶件)前模肉cavity（前模镶件）扣鸡P-lockblister 起泡blooming 起霜blow hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡center buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕orange peel 橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap 废料scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮折迭straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱折surging 波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)毛边flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤实用标准文档(Flow Line)流痕(Weld Line) 熔接线Sink Mark凹陷Streak条纹Warpage翘曲文案大全。
注塑常用英语
一、浇口(入水)：gate浇口进入位置：gate location浇口形式：gate type大水口(2板模)：edge gate, side gate细水口(3板模)：pin-point gate浇口大小：gate size转开关流道：switching runner/gate唧嘴直径：sprue diameter二、流道：runner热流道：hot runner，hot manifold温控箱：temperature controller热嘴冷流道：hot sprue/cold runner唧嘴直流：direct sprue gate圆形流道：round(full/half) runner模流道电脑分析：mold flow analysis流道平衡：runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探温针：thermocouples插头：connector plug插座：connector socket密封/封料：seal三、运水：water line喉塞：line plug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socket 四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold导柱(边钉/导边)：leader pin/guide pin导套(边司)：bushing/guide bushing顶针板：ejector retainer plate托板：support plate螺丝：screw管销(管钉)：dowel pin内模管位锁：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector sleeve pin推板：stripper plate缩呵：movable core，return core，core puller扣机(尼龙拉勾)：nylon latch lock斜顶：lifter模胚(架)：mold base上内模：cavity insert下内模：core insert行位(滑块)：slide镶件：insert压座(斜鸡)：wedge，heeled block耐磨板/油板：wedge wear plate压条：guide way plate模顶(撑头)：support pillar唧嘴：sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.S.(socket head shoulder screw) 杯头螺丝：S.H.C.S.(socket head cap screw)活动臂：lever arm分流锥：sprue separator垃圾钉：stop pin水隔片：buffle弹弓柱：spring rod弹弓：die spring中托司：ejector guide bush中托导套(边)：ejector guide pin镶针：insert pin波子弹弓：ball catch喉塞：pipe plug行位斜导柱：angle pin斜顶杆：angle ejector rod复位键/提前回杆：early return bar气阀：valves五、术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模闭合总厚度：mold base shut height顶针碰运水：water line interferes with ejector pin料位出上(下)模：part from cavity (core) side模胚原身出料位：cavity direct cut on A-plate，core direct cut on B-plate.不准用镶件：do not use (core/cavity) insert用铍铜做镶件：use beryllium copper insert初步(正式)模图设计：preliminary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length强度不够：insufficient rigidity均匀冷却：even cooling扣前模：sticking热膨胀：thermo expansion公差：tolerance铜电极(铜公)：copper electrode石墨电极：graphite electrode夹线：weld line翘曲：warpage缺胶：short shot困气：air trap毛刺：flash，burr~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~模具述语一、入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口：pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座：connector socket密封/封料：seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker 四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝：screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）：mold base上内模：cavity insert下内模：core insert行位（滑块）：slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴：sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate. 不准用镶件：Do not use (core/cavity) insert用铍铜做镶件：use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper electrode~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Surface Appearance 外观Glossiness/gloss finish 光洁度Matt finish/matt surface 毛面Glass fiber rich surface/glass emergence on the surface 玻纤外露Blooming/surface blooming 表面析出White patches on surface 表面白斑Silver marks/silver streak 银纹Splay mark 水纹Flow mark 流纹Weld line 溶结纹Brittle/brittleness 脆Bubbles/trapped gas 气泡Void 孔Burn marks 烧伤FR failed 阻燃不合格Flame rating V-2 阻燃V-2Poor dispersion 分散不好FR/PTFE …agglomerates etc 阻燃剂/PT FE…结块Pellet porous 粒子不密/蜜蜂窝Low impact/tensile etc 物理性能低High flow/filler content etc 流动性/填充…过高Longs/fines/doubles 长粒/碎屑/连粒Poor cut 粒形不好Bristle/voids 表面有小气泡/孔Glass bundles 玻纤结团Product was rejected due to 产品不能接受因为… High moisture level 高水分Warpage/warped 翘曲Shrinkage/shrink 收缩Sink marks 缩影Short shot/short molding 打不满Distortion 变形Over dimension 尺寸过大Under dimension 尺寸过小Flashing 飞边Discoloration 变色Off color 颜色差异Flow rate 流动率Viscous 粘High flow 高流动Low flow 低流动Sticky 粘Mold release 脱模Antioxidant 抗氧剂Flame retardant agent 阻燃剂Heat stabilizer 热稳定剂Chopped glass fiber 短切玻纤Roving glass fiber 粗纱/长玻纤Glass beads 玻璃微珠Milled fiber 碾磨纤Molybdenum disulfide/moly/MoS2 二硫化钼Colorant 着色剂Pigment 颜料Dye 染料Accepted product specification 接受产品规格Approved our product 认可我们的产品Re-set spec 重新定标准Add in extra … 添加多一点…Reduced … content 减少…含量Dropped/reduced … by x％减少…含量…％Confirmed color standard 确认颜色标准Approved color standard 认可颜色标准Re-confirmed color standard 重新确认颜色标准Qualified our product 认可我们的产品Undergoing heat aging test 在做热老化实验Product is under testing 产品在测试当中Received first order 接了第一个定单Expected to finish by … 预计在…完成Expected order is xMT 预计定单量…吨Estimated annual/monthly consumption 预计年/月用量。
模具注塑术语中英文对照
模具注塑术语中英文对照1. 模具制造工艺 - Mold Manufacturing Process•钳工技术 - Fitting Technology•铣床 - Milling Machine•车床 - Lathe Machine•电火花 - Electrical Discharge Machine (EDM) •线切割机 - Wire Cutting Machine (WCM)•抛光 - Polishing•喷砂 - Sandblasting•组装 - Assembly•检验 - Inspection•测试 - Testing2. 模具材料 - Mold Materials•CNC - Computer Numerical Control•冷/热工作钢 - Cold/Hot Work Steel•韧性铁 - Ductile Iron•钢筋混凝土 - Reinforced Concrete•铝合金 - Aluminum Alloy•有机玻璃 - Organic Glass•尼龙 - Nylon•聚酯树脂 - Polyester Resin•低密度聚乙烯 - Low-Density Polyethylene (LDPE) •高密度聚乙烯 - High-Density Polyethylene (HDPE) 3. 注塑设备 - Injection Molding Equipment•注塑模 - Injection Mold•注塑机 - Injection Molding Machine•螺杆 - Screw•加热筒 - Barrel Heater•喷嘴 - Nozzle•冷却系统 - Cooling System•熔融体 - Melted Polymer•定位环 - Locating Ring•压力机 - Press•模芯 - Core4. 注塑工艺 - Injection Molding Process•熔胶温度 - Melting Temperature •注射速度 - Injection Speed•保压时间 - Holding Time•冷却时间 - Cooling Time•射胶压力 - Injection Pressure•模具温度 - Mold Temperature•注射容量 - Injection Capacity•射出比例 - Injection Ratio•射胶速度 - Injection Rate•开模时间 - Opening Time5. 注塑缺陷 - Injection Molding Defects•缩水 - Shrinkage•气泡 - r Bubbles•热分解 - Thermal Degradation•断裂 - Fracture•变形 - Deformation•熔接线 - Weld Line•流痕 - Flow Mark•挤出线 - Extrusion Line•色差 - Color Variation•异物 - Foreign Object6. 模具维护 - Mold Mntenance•涂抹脱模剂 - Apply Mold Release Agent•清洁模具 - Clean the Mold•磨削模具 - Grinding the Mold•检查模具 - Inspect the Mold•修复模具 - Repr the Mold•涂覆保护液 - Coat with Protective Agent•封存模具 - Store the Mold•更换模具配件 - Replace Mold Components•消除模具表面缺陷 - Eliminate Surface Defects on Mold •升级模具材料 - Upgrade Mold Material以上是模具注塑术语的中英文对照，希望能对你有所帮助。
注塑专业名词
注塑专业名词中英文对照表英语名称中文名称Hopper Dryer 料斗干燥器Injection Molding Cycle 注塑周期Crushing Mill 粉碎机Precision Injection 精密成形Gas Injection/AGI 吹气成形、气辅成形Set the condition 设定注塑前提Machine 机械Mold Set-Up 上模Screw 螺杆、螺钉、螺旋Mold Down 下模Screw Head 螺杆头Pressure 压力Joint 接头，接缝Low Pressure 低压Injection 注塑Low Pressure Clamping 低压锁模Feeder 送料（加料）器Holding Time 保压时间Compound 混炼料Back Pressure 背压Blend 搅浑，调和Clamping Force 合模力Mixer 混淆器Hold Clamping Pressure 锁模型压成力Mixing 混淆Clamping Stroke 合摸行程Cooling 冷却Clamping Unit 锁模装配Cooling Tower 冷却塔Mold Opening 开模Chiller 冷水机Mold Closing 合摸Temperature Controller 温调机Speed 速率Cylinder 料筒Injection Speed 射出速率Heater 加热器Injection Capacity 注塑量Band Heater 加热圈Charging 计量Thermocouple 热电偶Charging Stroke 计量行程Nozzle 射嘴Rib 骨位，筋位，增强筋Nozzle Head 射嘴头子Insert 嵌件，镶嵌"Tie Bar,Tie Rod" 拉杆，拉杠Wall Thickness 胶厚，壁厚Distance Between Tie Rods 拉杆距离Plasticizing 塑化Limit Switch 限位（限定）开关Thermal Decomposition 热分化Operation Switch 操作开关Shrinkage 收缩Operation Guide 操作指南Resin 树胶Control Panel 节制器Material 原料，质料Automatic 全自己主动Plastics 份子化合物塑料，塑胶成品Semi Auto 半自己主动Rubber 橡胶Hand 手动Master Batch 色母Handle 手柄Powder 色粉，粉，粉末Extruder 押出机，挤塑机Dry Color 色粉，干色料Extrusion Molding 挤塑Pellet 粒，塑胶粒Blow Molding Machine 吹塑机"Glass Fiber,Fibrous Glass" 玻璃纤维Blow Molding 吹塑Hose 软管，管Program Control 步伐节制Over Packing 过充填Process 工艺，工序，历程Mold Mark 马克模伤，模痕Inject visor 注塑工艺步伐节制装配Shock 冲击Damage 损坏，毁伤Cold Slug 冷料Sink 马克抽水，紧缩Cold Slug Well 冷料井Short Shot 充填不足，欠料Freeze 冷凝Flash 毛刺，披峰Hydraulic 液压，油压String Flash 胶丝Ghydraulic Ejector 液压顶出，液压脱模White 马克白化，顶白Hydraulic Pump 液压泵Silver 雪白，银痕Hydrautic 摩托液压电动机Flow mark 流纹air compressor 空气压缩机，空压机burn 烧黑，烧焦oil leakage 漏油异物black spot 异物，黑点oil tank 油箱，油槽sticking 粘模piston 活塞weld 溶接线，联合线air cylinder 气缸flash 料花alarm 报警oil 马克油污，油渍safety gate 太平门damage 打痕，击伤emergency stop 紧迫遏制cracking 裂，开裂color change 换色jetting 气纹purge material 清机份子化合物塑料deform 变型resin thermal 胶料温度warping 屈曲，翘曲，外倾mold thermal 模温bend 屈曲，翘曲，外倾heat up 升温，升热torsion 扭曲air shot 空射蛟，空打uneven color 色彩不均匀try 试模Eccentric Wall thickness 壁厚不匀称mold release 脱模"bladder,cell" 气泡儿，浮泛，空地mold release agent 脱模剂stripes 条纹rust preventatives 防锈剂dirty 污痕，污点，渗溢can't release （产物）没有办法脱模flaking 脱落，剥落shot 注，射tear off 上下翻动gate 进点，浇口float 浮起center gate 中间浇口screw damage 螺钉滑牙sprue runner 水口，注口，流道料shortage 员数不足，欠品clearance 距离，余隔run out 跃动度，偏疼sprue 主流道注（塑）口contraction 紧缩runner 流道，流道料assembly NG 嵌合不良，装配不良air vent 散气眼，透风口stress 应力breathing 排气，散气internal stress 内部策应力anneal 热措置惩罚，退火preparation 摆设，筹办mold 生产模型stopper 挡块machining center 加工中间stripper 推板，脱模型板universal milling machine 刨床，锣床spacer plate 垫板latter 车床mould base 模胚surface grinder 最简单的面磨制机床support plate 托板grinding drilling 钻床support pillar 撑头electric discharge machine 火花机加工puller lock 拉塞wire EDM 线割切puller bolt 拉杆nitride steel 氮化钢取付板top clamp plate 工字板，水口板nitrogen 氮气bottom plate 底板nitride 氮化措置惩罚return 回针titanium 钛guider pin 导柱heat treatment 热措置惩罚guider bush 导套hardening 淬火die 生产模型，动模，移动模型板Temper 回火die plate 模型板，载模型板annealing 退火module 板块，模件，模数pre harden 预加硬钢parts 零件，生产模型零件hardness 硬度eye bolt 吊环螺栓soft 软，软的crane 吊车，行车electrodes 铜公hook 勾，吊勾insert 镶件wire 钢丝，钢丝绳slide 行位，滑块file 锉子taper 斜度oil stone 油石taper 斜度，锥度，锥形的sand paper 砂纸draft 脱模斜度mesh 节号，目guide pin 导向柱刻印engrave 刻印sleeve pin 司筒针texture 蚀纹square pin 扁顶针放电目EDM texture 火斑纹angular ejector 斜顶针rough 粗的cavity 模腔，前模，母模trifling 细的，幼的core 模心，后模，公模diamond cut 钻石纹number of cavities 取数，模腔数roulette 滚花刀，刻痕rocket ring 定位环blast 喷沙o ring O环，胶圈hot runner 暖流道wall trickness 肉厚，胶厚repair 补缀add material 加胶接welding 溶接，焊接building 加胶溶接机welder 焊机，电焊机cut material 减胶溶接棒welding rod 焊条，电焊条modify the tooling 改模（因设变补缀）argon arc welder 氩弧焊repairing the tooling 生产模型补缀torch bumper 喷燃烧现象器，火苗燃烧现象器design 预设ejector pin 顶出design drawing 预设图ejector pin 顶针design change 预设变动，设变gate type 水口体式格局designer 预设者，预设职员tunnel gate 隧道式浇口，潜入水下口designer 预设者pin point gate 针孔形浇口，细水口mold design 生产模型预设side gate 侧水口，洪流口mold specification 生产模型建造仕样书direct gate 直接浇口specification 规格multi gate 复式浇口mold construction 生产模型机关，生产模型布局fan gate 扇形浇口input 输入film gate 扇形浇口programming 编程jump gate 搭接浇口3D drawing 3D图，3维图gate balance 浇口均衡2D drawing 2D图，最简单的面图undercut 凹槽，倒扣front elevation 正面图cooling line 水管，运水plan 平面图cross-sectional drawing 剖面图cooling 冷却回路，运水CAD date CAD数值modeling 模mock-up 模子，原尺寸模子software 软体hand made sample 手板，手工样品mold drawing 生产模型图module 模数，模量，模件part drawing 零件图gear 齿轮，传动装配diagrammatic sketch 草图helical gear 螺旋齿轮drawing 绘图solid 群体的，固体revised drawing 图订变换transformation 变换，转换dimensioning 记入尺寸floppy disk 磁盘，软盘out mold direction 出模标的目的computer 台式机，计较机draft 出模斜度personal computer 私家用电器脑，手提台式机pitch 间距，齿距version 情势，品类（译文，翻译，译本）angle 角度reading 读取projected area 投影平面或者物体表面的大readout 读出taper 锥度，斜度reading 度数under cut 倒扣压缩compression 压缩2 plate 两板模开open 打开，读出文件（软体）3 plate 三板模not open 打（解）不开，读不出offset 偏置，偏移miss 纰缪，掉误mold layout 分模condition of the progress 进程项度状态split mold 对于开式生产模型finishing 打光，磨光slide core 滑动模芯polish 研磨，打磨loose core 勾当模芯target 方针，目的，对于准loose mold 勾当生产模型schedule 每一日安排表press 冲压，压床，压maintenance 维护，调养press machine 冲床did casting 压铸progressive 级进sintering 加热使黏结single 单冲monkey 勾当板子packing plate 垫板clamp 夹具（固定生产模型用）punch 冲头，凸模，冲床scrap 废铁，废物，废渣punch press 冲孔机rust 生锈die 下模rust inhibitor 防锈剂die set 模座，模架washing agent 洗濯剂press mold 冲压模，五金模ultrasonic cleaning 超音波洗濯leveler 整平滚，矫平机feeder 送料机，加料机burr 反边，毛刺drawing 拉伸thinner 天纳水，淡薄剂burring 去毛刺triclinic 三氯乙烯脱脂剂blank 复合trivalent chromium 六价铬cutting 落料，冲孔bending 折弯degreasing 脱脂，去油bend 折弯，屈曲harmful metal 有害物box-bending 箱cut 割切L-bending L折弯"press, sheet metal" 板金V-beding V折弯cut 堵截，割断punching 冲孔，钻孔iron plate 铁板SECC 镀锌板cutting 冲压，抽去silver top 镀锌板shirk 避空stainless 不锈钢calking 铆接copper 铜tap 螺丝攻brass 黄铜dies 板牙steel 钢reamer 铰孔aluminum 铝reamer 铰刀，扩孔器width 宽度end mill 刨刀thickness 板厚grinder 砂轮机，磨制机床density 疏密程度barrel 滚筒coil 卷材barrel tumbling 滚（捅抛）光width cut 片材plating 电镀nut 螺丝帽，螺帽electro plating vacuum 真空电镀bolt 螺栓，螺杆spot welding 点溶接，点焊chrome plating 镀铬jip 夹具，治具galvanization 镀锌clearance 间隙shave 切，削matching 接口assembly 装配，组装counter 统计器assembly unit 装配组件count method 统计法assembly time 装配工数timer 按时器line 生产线，拉线digital 数码（的），数码self 单人装配digital camera 数码拍照机conveyer 传送带connect 插座，插嘴U line U形出产线plug 插头，瓶塞capacitor 电器皿lamp 灯resistor 电阻器lighting 点灯，灯亮diode 二极管fuse 断电丝LED （light-emitting diode) 闪光二极管power code 电源线transistor 形成品体体管wire hamess 电线导线IC 集成电路bar code 条纹码lcd(liquid crystal display) 液态品体预示器vinyl tape 绝缘带sensor 传感器noise 异音，杂音，噪音relay 替续器decibel 分贝（声强单位）connector 保持器instruction sheet 功课引导书transformer 变压器access platform 功课台breaker 断路器series 串联buzzer 蜂鸣器parallel 并联printed circuit board/PCB 印刷电路板clutch 联轴器，聚散器driver 螺钉刀，起子solenoid coil 电磁线圈driver 十字批（起）coil 线圈driver 一字批（起）static electricity 静电electric drive 电动螺钉刀，电批prevent electricity 防静电torque 扭矩，转矩fan motor 电扇电动机screw 螺钉刀，起子grease 润滑washer 垫圈（片）apply 涂油e-ring 卡环block copy 底板，草图solder 焊锡film 胶卷，软片soldering iron 烙铁silk print 丝印tin 锡pat print 移印earth 接地，地线hot sample 烫印alcohol 火酒，乙醇ink 印字油墨foot switch 脚踏开关color sample 色板terminal 端子print NG 印刷不良terminal block 端子板bleeding 渗溢，飞油label 标贴，标签stamp 捺印bar code 条纹码，条形码spray 涂装，喷涂mile 软片，聚酯树胶wood graining 木纹加工quality control 品位办理sample 样品，样本，样板inspection 查抄boundary sample 限度样板IQC 验收，受入查抄approval sample 认可样板OQC 出货查抄tolerance 公役PQC 工程查抄plus 正，加号sampling 抽查minus 负，减号total inspection 全检disperse 不变，颠簸visual inspection 目视查抄unstable 不稳固appearance check 外不雅查抄balance 均衡patrol 巡检process capability /CP 工程能力measurement 丈量仪三角螺丝刀detection 检验测定measurement 张良，标定check point 查验（重）点measuring method 丈量要领no check 漏检clogging 刻度，分度special adoption application 特采审请memory 储存，影像provisional countermeasure 暂定对策three-dimensional measuring machine 3D丈量仪permanent countermeasure 长久对策microscope 东西目镜claim 投诉，抱怨，索赔profile projectior 投影机appraisal 评价slide calipers 卡尺decide 鉴定micrometer 量具，检查基准check standard 查抄基准lever type dial test 百分表检查基准表inspection sheet 查抄基准表torque gauge 扭转力计QC 工程表QC flow chart QC工程表scale 刻度尺specula face 镜面square 90度角尺mirror face 光面，光泽面steel tate 皮尺texture face 蚀纹面height gauge 高度尺first the face 一级面pin gauge 柱规appearance 外不雅面thickness gauge 片appearance part 外不雅产物protractor 角度仪function part 性能部品tension gauge 拉力机slide 滑动面indicator 百分表检查基准表flatness 最简单的面度hardness tester 硬度计reform 矫正multitester 万用表check jig 查抄用治具surface plate 平台，平板feed back 反馈V block V形块communication 信息，抱怨gauge block 方块规manual 指南，手册dial gauge 百分表flow chart 流程图data 数值process inspection 工程监查data sheet 数值单qualification 确定地认为parameter 参量graph 图表，曲线图warehouse 堆customhouse 海关pallet 卡板customs clearance 报关，通关corrugated fiberboard 纸箱customs clearance 报关手续partition 刀卡electronic data interchange 电子报关recycle box 周转箱container 货柜车plastics box 折叠式周转箱foot 英尺container 份子化合物塑料周转箱packing list 装箱单poly-bag 胶袋list 详细登记单tape 封箱品牌一字螺丝刀胶纸declaration 申请报告rope 绳索，线import 入口first in first out 先入先出export 出口fork lift 铲车fumigation certificate 熏蒸证实书hand lift 手推铲车no wood packing certificate 无木质包装证实书bogie 台车wooden box 木箱truck 卡车shelf 货架license 批文，容许stock 在库数license document 转厂shelf 盘货limits 指标，配额指标dead stock 死仓储，积压品import limits 入口指标purchasing 采集购买unbalance 数目不服衡supply parts 支给品contract 合约purchase parts 采集购买品contract 手册lead time 交货期，定货期order placement 发定单"transfer,carry over" 转余料，拨余料pay 有偿erase 核销free of charge 没有报酬的provision of information 加签vender 供应商submit document 递单quotation 报价单brand name 商物品名称invoice 发票，请款单goods No 商品编码deposit 预付款，包管金foreign enterprise 外资企业payment 付款owned enterprise 独资企业payment condition 付款partnership enterprise 合资工厂month payment 月结processing 来料加工over time 加班（没事了事情日加班）bailment processing 委托加工over time fee 加班费labor cost 人件费holiday work 加班（节假日上班）amortization 折旧费two shift 两班制hour charge 加工费，工时费day shift 白班exchange rate 汇价night shift 晚班material certificate 质料证实书。
注塑常用术语英文表达
1.雾气Moisture Streaks2.玻纤分配不均Glass Fiber Streaks3.困气Gas Trap Effect4.银丝纹Sliver Marks5.结合线Weld Line6.水波痕Water Wave Effect7.黑点Dark Sport8.顶出印Visible Ejector Marks9.变形Deformation During Demolding10.填充不足Short Filling11.冷料流痕Cold Slug12.进胶口点不良Dull Spots Near The Sprue13.喷射痕Jetting14.表面起层Flaking Of The Surface Layer15.浮泡Entrapped Air16.过热变色Burnt Streaks17.龟裂Stress Crack18.缩水痕Sink Marks19.真空气泡Density Bubble20.披锋Flash21.擦伤印Scratch MarksGlass fiber rich surface/glass emergence on the surface22 尺寸过大Over dimension23尺寸过小Under dimension24 翘曲Warpage/warped25 收缩Shrinkage/shrink26 缩影Sink marks27 打不满Short shot/short molding塑料模具mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板support plate方铁spacer plate底针板ejector plate面针板ejector retainer plate回针Return pin导柱Guide pin有托导套Shoulder Guide bush直导套Straight Guide bush动模座板Bottom clamp plate Moving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould 动模movable mould, movable half上模upper mould，upper half下模lower mould，lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具three plate mould脱模ejection换模腔模具interchangeable cavity mould脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller 立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine。
注塑术语
中文英文机工,机器加工 machining,machine workO环,O形封垫 O ring下料模,切料模 blanking die寸进,寸动 inching工程塑胶 engineering plastics工模,夹具,支架 jig干胶,粘著剂,动物胶 glue干燥时间 drying time干燥剂 drier dryer不划一颜色,颜色深浅不均 color non-uniformity 中心浇口 center gate内衬,衬套,衬蛰 liner公差,容差 tolerance分模线,合模线,模缝痕 parting line切口,缺口 notch切口,缺料 notch切边(n) shear edge化学腐蚀 chemical atching化学腐蚀 chemical etching反射 reflection孔隙,空洞,气泡 void尺寸稳定性 dimensional sability手动压机 hand press支管形喷嘴 nozzle manifold比重 specific gravity比热 specific heat毛状裂痕 hair crack,hair cracking毛绒 fuzz毛边,凿纹 burr,flash,fin水道,水通路 water channel火花放电 spark discharge火焰处理 flame treatment,flame treating片材 sheet凹痕,缩痕 sink mark,shrink mark凹槽,内陷,凹陷 undercut加料,给料,供料 feed加热,加温 warming,warming up加热板,热板(盘) heating plate加热管套,加热缸 heating cylinder,heating barrel 加热炉 heating furnace功率,力率 power factor半透明 semitransparence,translucence打眼,钻孔 driling正余面,交叠,重叠 overlap永久变形 permanent set,residual strain白昙,雾状 haze立式射出成型机 vertical injection mo(u)lding machine光彩,光泽 gloss印刷 printing同轴往复螺杆式射出成型机 in-line screw(type)injecton mo(u)lding machine 合成树枝 synthetic resin合板,集成材 composite wood合模力,开模力 mo(u)ld clamping force,mo(u)ld locking force合模线,毛边线 flash line,parting line合模线,毛边线 spew line,spue line合模销,导销 leader pin合模销套,导销衬套 leader pin pushing合模机构,开模机构 mo(u)ld clamping mechanism后加工 post processing后加热 after baking后成型 postforming回程销,复归销 return pin安全系数 safety factor安全门 safety door成孔销,心型销,模蕊销 core pin成孔销托板,动或定模板 core pin plate成形 forming成形,模制 mo(u)iding,forming成形收缩率,模制收缩率 mo(u)ld shrikage,mo(u)lding shrikage成形指数 mo(u)lding index成形时间 mo(u)lding time,cycle time成形循环(周期) mo(u)lding cycle成形温度,模制温度 mo(u)lding temperature成形压力,模制压力 mo(u)lding pressure成型纹(缺陷) mo(u)ld mark成型销,心型销,模蕊销 core pin托板,模板,承装模穴(蕊)块之模板 retainer plate托板,模板,承装模穴(蕊)块的模板 retainer plate收缩 shrinkage有机溶胶 organosol污染 contamination自动顶出 automatic ejection自动浇口,剪切浇口 shear gate色片,色粒 color chip色相 hue色彩度 chroma行程,冲程 stroke伸长,变形 elongation,strain伸长计 extensomenter冷却水塔 cooling tower冷却套管 cooling sleeve冷料 cold slug吸水性 water absorption吸收 sbsorption吸附作用 adsorption含量(率) content扭力试验,扭曲试验 torsion test,torsional test,twist test 折曲加工 folding折射率,折光指数 refraction index沈陷式浇口,潜入式浇口 submarine gate沈积,淀积 sedimentation冲切 punching冲头 punch车削 turning供料段,加料段 feed zone,feed section刮伤,刺蚀,擦伤处 abrasion卷尺,胶带 tape卷转,翘曲 curling,curl固定侧,模穴侧 cavity side延伸,拉伸 drowing,orientation,stretching延性 ductility往复应力,振幅应力 alternating stress拉伸比,牵引比 draw ratio抽引,凸包 embossing放电加工 electro-discharge machining放电处理 electro-discharge treatment注道,竖流道,注道料 sprue注道冷料顶出 sprue ejection,sprue ejector注道冷料顶出销 sprue djector pin注道形浇口,直接浇口 suprue gate注道拉取器,浇口钩销 sprue puller注道衬套,浇口衬套 sprue bush,sprue bushing油漆 oil varnish泛白 blushing直接浇口 direct gate空气顶出 air ejection冲压模具英语冲压英语stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to.to send delinery backto retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑common vocabulary for die engineering模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die 连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓。
注塑英语专业名词
1.雾气 Moisture Streaks2.玻纤分配不均 Glass Fiber Streaks3.困气 Gas Trap Effect4.银丝纹 Sliver Marks5.结合线 Weld Line6.水波痕 Water Wave Effect7.黑点 Dark Sport8.顶出印 Visible Ejector Marks9.变形 Deformation During Demolding 10.填充不足 Short Filling 11.冷料流痕 Cold Slug12.进胶口点不良 Dull Spots Near The Sprue 13.喷射痕 Jetting14.表面起层 Flaking Of The Surface Layer 15.浮泡 Entrapped Air 16.过热变色 Burnt Streaks 17.龟裂 Stress Crack 18.缩水痕 Sink Marks19.真空气泡 Density Bubble 20.披锋 Flash21.擦伤印 Scratch MarksGlass fiber rich surface/glass emergence on the surface 22 尺寸过大 Over dimension 23尺寸过小 Under dimension 24 翘曲 Warpage/warped 25 收缩 Shrinkage/shrink 26 缩影 Sink marks27 打不满 Short shot/short molding塑料模具mould of plastics 注塑模具injection mould 冲压模具die 模架mould base 定模座板Top clamping plate Top plateFixed clamp plate水口推板stripper plate A板A plate B板B plate支承板 support plate 方铁 spacer plate 底针板 ejector plate面针板 ejector retainer plate 回针 Return pin导柱 Guide pin有托导套 Shoulder Guide bush 直导套 Straight Guide bush 动模座板Bottom clamp plate Moving clamp plate 基准线datum line 基准面datum plan型芯固定板core-retainer plate 凸模固定板punch-retainer plate 顶针ejector pin单腔模具single cavity mould 多腔模具multi-cavity mould 多浇口multi-gating 浇口gate 缺料starving 排气breathing 光泽gloss合模力mould clamping force 锁模力mould locking force 挤出extrusion 开裂crack循环时间cycle time 老化aging 螺杆screw 麻点pit 嵌件insert活动镶件movable insert 起垩chalking浇注系统feed system 主流道 sprue 分流道runner 浇口gate直浇口direct gate , sprue gate 轮辐浇口spoke gate , spider gate 点浇口pin-point gate 测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well 浇口套sprue bush 流道板runner plate 排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould 动模movable mould, movable half上模upper mould， upper half 下模lower mould， lower half 型腔cavity凹模cavity plate，cavity block 拼块split 定位销dowel定位销孔dowel hole 型芯core斜销angle pin, finger cam 滑块slide滑块导板slide guide strip 楔紧块heel block, wedge lock 拉料杆sprue puller 定位环locating ring 冷却通cooling channel 脱模斜度draft 滑动型芯slide core 螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould 熔合纹weld line （flow line）三板式模具three plate mould 脱模ejection换模腔模具 interchangeable cavity mould 脱模剂release agent 注射能力shot capacity 注射速率injection rate 注射压力injection pressure 差色剂colorant保压时间holdup time 闭模时间closing time 定型装置sizing system阴模female mould，cavity block 阳模male mould电加工设备Electron Discharge Machining 数控加工中心CNC machine center 万能铁床Universal milling machine 卧式刨床Horizontal planer 车床Engine lathe平面磨床Surface grinding machine 去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller 立式钻床Vertical driller 超声波清洗机Ultrasonic clearing machine。
注塑常用术语英文表达
1.雾气Moisture Streaks2。
玻纤分配不均Glass Fiber Streaks3.困气Gas Trap Effect4。
银丝纹Sliver Marks5.结合线Weld Line6.水波痕Water Wave Effect7。
黑点Dark Sport8。
顶出印Visible Ejector Marks9。
变形Deformation During Demolding10.填充不足Short Filling11。
冷料流痕Cold Slug12。
进胶口点不良Dull Spots Near The Sprue13。
喷射痕Jetting14.表面起层Flaking Of The Surface Layer15.浮泡Entrapped Air16。
过热变色Burnt Streaks17。
龟裂Stress Crack18。
缩水痕Sink Marks19。
真空气泡Density Bubble20。
披锋Flash21。
擦伤印Scratch MarksGlass fiber rich surface/glass emergence on the surface 22 尺寸过大Over dimension23尺寸过小Under dimension24 翘曲Warpage/warped25 收缩Shrinkage/shrink26 缩影Sink marks27 打不满Short shot/short molding塑料模具mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板support plate方铁spacer plate底针板ejector plate面针板ejector retainer plate回针Return pin导柱Guide pin有托导套Shoulder Guide bush直导套Straight Guide bush动模座板Bottom clamp plate Moving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch—retainer plate顶针ejector pin单腔模具single cavity mould多腔模具multi—cavity mould多浇口multi—gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道sprue分流道runner浇口gate直浇口direct gate ，sprue gate轮辐浇口spoke gate ，spider gate 点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold—slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould 动模movable mould，movable half 上模upper mould, upper half下模lower mould，lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin，finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具three plate mould脱模ejection换模腔模具interchangeable cavity mould脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller 立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine。
完整的注塑专用英语大全-专用技术术语 注塑人必备
Surface Appearance 外观Glossiness/gloss finish 光洁度、粗糙度Matt finish/matt surface 毛面Glass fiber rich surface/glass emergence on thesurface 玻纤外露、浮纤Blooming/surface blooming 表面析出White patches on surface 表面白斑Silver marks/silver streak 银纹Splay mark 水纹、料花Flow mark 流纹，流痕Brittle/brittleness 脆、脆性Bubbles/trapped gas 气泡/困气V oid 孔、气泡Burn marks 烧伤FR failed 阻燃不合格Flame rating V-2 阻燃等级V-2Poor dispersion 分散不好FR/PTFE …agglomerates etc 阻燃剂/PTFE…结块Pellet porous 颗粒料孔隙、Low impact/tensile strength etc 低冲击强度/拉伸强度等High flow/filler content etc 高流动性/过度填充Longs/fines/doubles 长粒/碎屑/连粒Poor cut 粒形不好Bristle/voids 表面有小气泡/孔Glass bundles 纤维结团Product was rejected due to 产品不能接受因为…High moisture level 高水分、高湿度Warpage/warped 翘曲/变形Shrinkage/shrink 收缩/收缩率Sink marks 凹陷、缩水Short shot/short molding 打不满、欠注、缺料，短射Distortion 变形Over dimension 尺寸过大Under dimension 尺寸过小Flashing 飞边、披锋、溢边Discoloration 变色Off color 颜色差异Flow rate 流动速率Viscous/viscosity 粘性的、粘的/黏度High flow 高流动Low flow 低流动Sticky 粘的，粘性的Sticking core 粘后模，粘模芯Sticking sprue 粘水口Sticking cavity 粘前模Mold release（agent）脱模(剂)Antioxidant 抗氧剂Flame retardant agent 阻燃剂Heat stabilizer 热稳定剂Chopped glass fiber 短切玻纤Roving glass fiber 粗纱/长玻纤Glass beads 玻璃微珠Milled fiber 碾磨纤Molybdenum disulfide/moly/MoS2 二硫化钼Colorant 着色剂Pigment 颜料Dye 染料Accepted product specification 接受产品规格Approved our product 认可我们的产品Re-set spec 重新定标准Add in extra …添加多一点…Reduced …content 减少…含量Dropped/reduced …by x％减少…含量…％Confirmed color standard 确认颜色标准Approved color standard 认可颜色标准Re-confirmed color standard 重新确认颜色标准Qualified our product 认可我们的产品Undergoing heat aging test 在做热老化实验Product is under testing 产品在测试当中Received first order 接了第一个定单Expected to finish by …预计在…完成Expected order is xMT 预计定单量…吨Estimated annual/monthly consumption 预计年/月用量模具方面：Ejection system 顶出系统、脱模系统pin 顶针、推杆spring 弹簧Gate type 浇口类型sprue 主流道runner 分流道cavity 模腔Sprue gate 直浇口Pin point gate 点浇口Tab gate 护耳浇口Fan gate 扇形浇口Tunnel or submarine gate 潜伏式浇口Jump gate 跳跃式浇口Diaphragm gate 片状浇口Ring gate 环形浇口The cavity of the mould 模腔Heated cylinder 加热料筒Surface finish 表面光洁度Sink mark 缩水Air trap 困气Gas trapped 气体困着，困气void 空隙，孔galling 烧焦Weld line 熔接痕，熔合线Drag mark 划伤、脱模痕Scratch mark 模具刮花Deformed/ warp 变形Ejector not returned 顶针不回位slide 滑块、行位streak 波纹、条纹、色痕delamination 分层Jetting mark 喷射痕Gate mark 浇口痕rib 筋、加强筋、骨位boss 凸台、凸起、凸痕Melt flow length 熔体流线长度Ejector plate 顶针板Stop pin 限位销Push rod 推杆、顶针Push back pin 复位杆Ejector guide pin 顶针导柱Cold-slug-well 冷料井、冷料穴plate 模板Ejected mark 顶痕，顶白nozzle 喷嘴Surface defect 表面缺陷Air vent 排气口Filling uneven 走胶不平衡、进胶不平衡。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
注塑方面英语术语
压铸die-cast
压炼injection
铸件casting/cast/founding
起泡/气泡bubble/blister/air bubble
缺料shor-shots/undershot
浇不足/*铸under-founding
多料superfluities/superfluous material(alloy) 顶针痕ejector (pins) mark
花纹flow mark/flow line
冷纹cold mark/cold streak
油纹oil streak
走水纹splash mark
银纹silver streaks
霜纹splay mark
夹水纹silver streaks/flow line/weld line
扣模/粘模sprue sticking
砂眼/气眼air hole
（塑胶件）弯曲/变形warping/warpage
变形deformation
扭曲twist
翅曲warp/warped
材料错误using wrong plastic material 凸痕convex mark
凹位/凹陷sink mark/dent mark
披锋flashing
批损pare-mark/cut mark
批凹pare off
锉纹trim-mark/file-mark
锉损excessive trim mark
黑点/黑纹black spots/black streak
发白white mark
烧焦burn marks
刮花/刮痕scratch mark
擦痕/擦伤rub-mark/brush-burn
裂缝cracking
裂纹craking line
碰损stress mark
起皮chip
错位（合模线）part line misaling ment
孔位尺寸改变dimension various
哑色dull color
表面变光滑（喷油面）glossy finishing
表面sruface/outside
镶件insert/insert word
缩水/收缩sink mark/shrinkage/shrink mark 偏差color deviation
色粉colourment
颜色colour/color
零件污糟dirty mark on part
顶白stress mark/ejector mark
屈曲bent
夹模线移位part line misalignment
胶件料厚不均uneven wall thickness
水口料degraded material
凹印sink mark
擦花abrasion mark
混色contamination mark
热点不良poor heat sticking
定位圈locating ring
唧嘴sprue bush (浇口套)
A板 A plate (定模板)
B板 B plate（动模板）
方铁spacer block (垫铁)
底板bottom clamp plate(动模底板) 面板top clamp plate(定模底板)
顶针ejector pin（顶杆）
直边钉guide pin (导柱)
托司shoulder guide bush(导套)
直司straight guide bush(导柱)
回针return pin(回程杆)
细水口边钉support pin(副导柱)
蓝弹簧blue spring（回程弹簧）
水口推板runner stripper plate(卸流道板) 中边钉ejector guide pin (顶板导柱)
顶针板ejector retainer plate(顶杆固定板)
顶针底板ejector plate(顶杆垫板)
撑头support pollar（支撑柱）垃圾钉stop pin (限位钉)
呵core (后模肉镶件)
后模肉back mold body(后模镶件) 前模肉cavity（前模镶件）
扣鸡P-lock
blister 起泡
blooming 起霜
blow hole 破孔
blushing 泛白
body wrinkle 侧壁皱纹
breaking-in 冒口带肉
bubble 膜泡
burn mark 糊斑
burr 毛边
camber 翘曲
cell 气泡
center buckle 表面中部波皱
check 细裂痕
checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷
color mottle 色斑corrosion 腐蚀
crack 裂痕
crazing 碎裂crazing 龟裂deformation 变形
edge 切边碎片
edge crack 裂边
fading 退色
filler speak 填充料斑fissure 裂纹
flange wrinkle 凸缘起皱flaw 刮伤
flow mark 流痕
galling 毛边
glazing 光滑
gloss 光泽
grease pits 污斑
grinding defect 磨痕haircrack 发裂
haze 雾度
incrustation 水锈indentation 压痕
internal porosity 部气孔mismatch 偏模
mottle 斑点
necking 缩颈
nick 割痕
orange peel 橘皮状表面缺陷overflow 溢流
peeling 剥离
pit 坑
pitting corrosion 点状腐蚀plate mark 模板印痕
pock 麻点
pock mark 痘斑
resin streak 树脂流纹resin wear 树脂脱落riding 凹陷
sagging 松垂saponification 皂化scar 疤痕
scrap 废料
scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕
shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕
skin inclusion 表皮折迭straightening 矫直
streak 条状痕
surface check 表面裂痕
surface roughening 橘皮状表皮皱折surging 波动
sweat out 冒汗
torsion 扭曲
warpage 翘曲
waviness 波痕
webbing 熔塌
weld mark 焊痕
whitening 白化
wrinkle 皱纹
missing part漏件
wrong part错件
excessive defects过多的缺陷critical defect极严重缺陷
major defect主要缺陷
minor defect次要缺陷
not up to standard不合规格
dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良
slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点
mildewed=moldy=mouldy发霉
rust生锈
deformation变形
burr(金属)毛边
flash(塑件)毛边
poor staking铆合不良
excesssive gap间隙过大
grease/oil stains油污
inclusion杂质
painting peel off脏污
shrinking/shrinkage缩水
mixed color杂色
scratch划伤
(Flow Line)流痕
实用标准文档
(Weld Line) 熔接线
Sink Mark凹陷
Streak条纹
Warpage翘曲
文案大全。