注塑模具专业词汇
注塑模具英语词汇
注塑模具英语词汇-CAL-FENGHAI.-(YICAI)-Company One1注塑模具英语词汇一、工程部 / Design department:1) Designer - 设计师。
2) Assembly drawing - 模具组装图。
3) Mold layout - 模具结构图。
4) 2D product drawing - 2D产品图。
5) 3D product data - 3D产品数据。
6) Part drawing - 散件图。
7) Insert molding - 镶件模。
8) 2 color mold / Double injection tool - 双色模。
9) Hydraulic system - 油/水压系统。
10) Parting line - 分模线。
11) Air venting - 排气槽。
12) Cooling system - 冷却系统。
13) Screw - 镙丝。
14) Hot runner system - 热流道。
15) Valve gate - 伐针入水口。
16) Fan gate - 扇型入水口。
17) Pin point gate - 针点进胶。
18) Moon gate / Banana gate - 香蕉，象牙入水口。
19) Submarine gate - 潜水口。
20) Injection machine tonnage - 注塑机吨数。
21) Number of cavity - 穴数。
22) Steel - 钢材。
23) Copper - 铜。
24) Tungsten copper - 钨铜。
25) Beryllium copper - 铍铜。
26) Hardening - 加硬/淬火。
27) Tempering - 回火。
28) Chroming - 电镀。
29) Painting - 喷漆。
30) Resin - 胶材。
31) Printing - 丝印。
注塑模具英文专业词汇大全
组合铣顶块Assemble mill紫(纯)铜copper注塑模具injection mold注塑机injection machine注射压力injection pressure注射速率injection rate注射能力shot capacity主流道sprue直浇口direct gate支承板support plate再生料recycle material预热preheating银条Silver streak移印pad printing循环时间cycle time型腔cavity斜销angle pin镶件Insert万能摇臂钻床Universal radial movable driller 万能铁床Universal milling machine脱模斜度draft脱模剂release agent脱模ejection涂层coating凸模core plate锁模力clamp force缩水Sink mark丝印Silk screen printing水路钻孔加工drill water holes双色注塑Double injection molding 双色注塑2K injection数控加工中心CNC machine center 试生产Trial run; Pilot run (PR)烧焦Burn mark三板式模具three plate mold熔合线Welding line热熔Heat staking热流道模具hot-runner mold缺料Short mold青铜bronze切料头Degate翘曲变形Deformation嵌件注塑Insert molding潜伏浇口submarine gate气印gas mark气泡Bubbles破裂Crack平面磨床Surface grinding machine配料compounding排气槽vent尼龙nylon能力Capability膜内注塑IMD molding ( In-mold decoration）模流分析mold flow analysis模架mold base麻点pit螺纹型芯threaded core螺杆screw流痕Flow mark流道板runner plate料斗hopper量产mass production立式钻床Vertical driller老化aging拉料杆sprue puller困气air trap快速成型模Rapid prototype tool （RPT）开裂crack精加工CNC machining浇口套sprue bush浇口残留gate vestige浇口gate键槽keyway键Key间距pitch机械手Robot回位销Return pin黄铜brass滑块slide滑动型芯slide core黑条Black streak合模力clamping force合模mold spotting合模Bed out高光注塑Mold in color(MIC)分型线（面）parting line分流道runner飞边flash方铁spacer plate多腔模具multi-cavity mold短射short injection动模座板Moving clamp plate动模装配/定模抛光Assembly core side/Polishing 动模movable mold定位环locating ring定模座板Fixed clamp plate定模Fixed mold顶针ejector pin电脉冲加工EDM电脉冲加工EDM电加工设备Electron Discharge Machining点浇口pin-point gate倒角chamfer导柱Guide pin单腔模具single cavity mold粗加工CNC rough machining冲床Punch machine超声熔接Ultrasonic welding (USW）产能Capacity测浇口edge gate参数Parameter采购备料Order steel表面光泽不良Lusterless 表面剥离Pelling变形warpage闭模时间closing time保压时间holding time薄壁注塑Thin wall molding 凹模cavity plate，T0试模To Tool TrialB板B plateA板A plate3D数据设计3D design。
注塑模具专业英语
注塑模具专业英语Injection Mold Technical Terms（一）模具专业基本用词Professional Terms1．塑料— plastic, resin2．样件— sample3．钢料— steel4．注塑机— injection machine, press5．产品— part, product, moulding6．模具— mold, mould, toolA 简易模（样板模）— prototype moldB 量产用模具—production mold 7．三维造型（数模）—3D model, 3D data8．二维产品图— 2D part drawing9．设计— design10．制造— manufacture, build up, construction, fabrication, make11．检验— check, inspection12．测量— measure, inspection13．修改— change, modify, correction14．工程更改— engineer change15．质量— quality16．数量— quantity17．基准— datum, reference（二）如何解析2D 产品图？How to read 2D part drawing?一．产品几何Geometry1．点— point2．线（边）— line, edge3．面faceA 侧面— sideB 表面— surfaceC 外观面—appearance surface 4．壁厚—wall thickness, stock thickness5．加强筋（骨位）— rib6．孔— hole7．细长的槽— slot8．柱位— boss9．角— cornerA 圆角— filletB 倒角— chamferC 尖角— sharp corner 10．斜度— angle, taper11. 凹槽—recess , groove二. 分模信息Splitting1．分型线— parting line (P/L), splitting line2．主分模方向— main direction, line of draw3．浇口设定— gating一．产品标识Part Identification1．产品名称— part name (P/N)2．产品编号+版本号— part number + revision (Rev.)3．型腔号— cavity number4．材料标记— material symbol5．模具编号— mold number (no.)6．日期印— dating insert, date code7．循环印— cycling code8．公司标志— company logo二. 技术要求Specification (Special Requirement)1．项目启动表Kick-off sheet1）项目名称— program name, project name2）产品名称— part name, product name, part description3）产品编号— part number (P/N)4）客户模号— customer mold no.5）项目启动日期— kick off date, start date6）项目完成日期— due date, lead time7）内模件用钢— tool steel8）型腔数量— number of cavities9）数据文件编号— data file no.10）注塑材料— resin, plastic, raw material11）收缩率— shrink, shrinkage, shrink factor12）注塑机吨位—molding machine size, injection machine size 13）成型周期— cycle time14）型腔光洁度— cavity polish15）型芯光洁度— core polish16）皮纹（晒纹）— texture, grain17）拔模斜度— draft angle, removal taper18）注塑件颜色及光泽— molded color & gloss19）模具加工地— manufacturing facility20）热流道供应商—manifold manufacturer, manifold supplier 21）浇口位置— gate location / position22）浇口类型— gate type产品标识— stamp information, part identification特殊要求— special instructions1．产品质量及外观要求Part Quality & Appearance Requirement 1）尺寸及公差Dimension & Tolerance①重要尺寸— critical dimension, important dim., key dim.②理论尺寸— nominal dimension③实际尺寸— actual dimension④公差— tolerance⑤公差带— tolerance range⑥尺寸超差— dimension deviation⑦接受（合格）— accept, OK⑧拒绝（不合格）— reject, refuse, obsolete, NG⑨让步接受— concession, special admit⑩返工— re-work2）产品缺陷（常见的）Defects (normal)①缩水— sink mark, shrinkage②飞边，毛边— flash, burr③段差— mismatch discrepancy④银丝纹，蛇纹— snake marks, streak⑤弯曲，变形— warpage, distortion⑥打不饱（缺料）— short shot⑦熔接线— weld line⑧多胶— unwanted plastic⑨拉伤—damage2．产品外观Part Appearance①产品颜色— part color②产品光泽— gloss③皮纹粒度— grain3．常用词汇、词组及短语Normal Word, Short Sentence1）单边— per side2）双边— both sides3）加入，添加— add, incorporate4）去除，取消— remove, cancel5）满足…的要求，符合，与…要求一致—according to, conform to, satisfy, meet 6）要求，需要— require, need, demand 7）确认—be approved, agreed by …8）允许— permit, allow1）在…范围之内— within2）不可以，不允许，禁止— free from, prevent, avoid3）…，除非有另指—… unless otherwise specified4）…或少于—…or less5）自动化运作— automatic operation6）未注尺寸（详细形状）见三维造型Non dimensioned contour (detailed shape) see 3D model.7）分型线上的飞边（披缝）或段差应小于…Burrs o r discrepancy on t he P/L shall be … or less.标题栏Title Block1．产品名称— part name2．图纸编号+ 版本号（索引号）— drawing no. + level (index) 3．一般公差— general tolerance（三）如何阅读制模标准？How to read tooling standard?一．模具结构术语Mold Construction TermsA．模架Mold Base1．模架量化特征Measurement Feature①长X 宽X 高— Length X Width X Height②模具高度尺寸（模厚）— stack height of mould③模具重量— total weight of mould, mould thickness2．定模底板— front plate, top clamping plate, clamp plate, clamping plate3．定模板— cavity plate, fixed mould plate, A – plate4．动模板— core plate, moving mould plate, B – plate5．支撑板— support plate, backing plate6．间隔板,方铁— support blocks, rails, risers, spacer block7．顶杆固定板— retaining plate, ejector retaining plate8．顶板— ejector plate，bottom clamping plate9．动模底板— back plate10．导柱— guide pillar, leader pin, guide pin11．导套— guide bush, leader pin bush12．复位杆— return pin, push-back pin13．弹簧— spring14．撑头— support pillar15．顶针板导柱、导套— ejection guide pin / bush16．垃圾钉— stop pin, stop button17．模脚— standing-off pillars18．标牌— plaque scutcheonB．成型零部件moulding components1．型芯— core insert2．型腔— cavity insert3．镶针— core pin4．镶块— sub-insert, split5．滑块— slide, sliding split6．斜顶— lifter, angled-lift split, loose coreA 斜顶头— lifter headB 斜顶杆— lifter rod, lifter shaft 7．成型顶杆— moulding face pin, form pinC．浇注系统Feed System1．塑料Mouldinga．主流道— sprueb．分流道runner①主分流道—main runner ②二级分流道— branch runner 分流道断面形状cross-sectional shape of runner①圆形— full round②半圆形— semicircular③梯形—trapezoidalc．浇口gate常用浇口形式normal gate type :①边缘浇口（J型浇口）— edge gate, J – gate②侧浇口— side gate③潜伏式浇口—sub-gate, subsurface gate, submarine gate, cashew gate④潜伏式二次浇口(隧道式浇口) — tunnel gate onto feeder post⑤点浇口— pin gate⑥直接浇口(主流道型浇口) — sprue gate, direct gate⑦护耳式浇口— tab gated．模腔— impressione．冷料井— cold slug wellf．热流道— hot runner2．模具零件mold componentsa．定位圈— locating ring, location ring, register ringb．浇口套— sprue bushc．挡圈— stop ringd．浇口镶块— gate inserte．热流道板— manifoldf．热嘴— hot drop\hot sprue分型面及其锁紧、排气Parting Surface, inter-locking & venting 1．分型线— parting line ( P/L )2．镶拼线— bodyline, joint line3．平/ 不平的分型面— flat / non – flat parting surface 4．封胶面— shut off surfaces, seal-off surfaces5．擦穿位— shut off6．碰穿位— kiss-off7．管位— parting line lock8．分型面的释放(避空) — relief of parting surface9．分型面的平衡— balancing of parting surface10．锁紧角度— locking angle11．锁紧力— clamping force12．锁模块— safety strap13．精定位— Interlock, die lock14．困气— air trap15．排气槽— vent, vent slotE．滑块机构Slide1．驱动Actuation①斜导柱— angle pin, horn pin, cam pin②弹簧— spring③油缸— hydraulic cylinder2．制动Detention①滑块固定器— slide retainer②弹簧制动器— spring-loaded detention (plunger)③挡钉、挡板— stop pin, stop plate, slide stop3．导轨— gib, guide strip4．锁紧块（楔紧块）— heel block, locking heel, wedge block, chase block 5．耐磨片— wear plate, wear strip6．压板— retainer, gib7．螺钉— screw8．定位销— dowel pinF．斜顶机构Lifter1．斜顶头— lifter head2．斜顶杆— lifter rod, lifter shaft3．开口销— split pin4．固定板（压板）— retainer plate5．耐磨片— wear plate1．铜导套— bronze bushing2．衬套— spacer3．导轨— L – gib4．滑动块— slideG．顶出系统Ejection System1．基本词汇Basic Word①顶出行程— ejection stroke②模具开档— daylight③粘模— stick④产品脱模—part is push off from, clear part of mould,separation of part 2．顶板机构Ejector plate assembly①顶板— ejector plate②顶板固定板— retaining plate③推板— stripper plate④推板导柱— ejector guide pin⑤推板导套— ejector guide bush⑥撑头— support pillar3．复位机构Return System①复位杆（回程杆）— return pin, push – back pin②垃圾钉— stop pin, stop button③压簧— compressed spring④碟簧—a stack of ―Belleville‖ washers⑤早复位机构— early return system⑥强制复位机构— positive return system4．顶出方法Ejection Techniques1）顶杆顶出— pin ejection2）顶管顶出— sleeve ejection3）顶块顶出— bar ejection4）扁顶顶出— blade ejection5）顶板顶出— stripper ejection6）油缸顶出— hydraulic ejection7）气顶— air ejection8）阀门顶出— valve ejection5．顶出元件Ejection Elements1）拉料杆— sprue puller, sucker pin2）顶杆— ejector pin3）阶梯式顶杆— stepped ejector pin1）顶管— ejection sleeve, sleeve2）扁顶— ejector blade, slabbed off ejector pin3）顶块— stripper bar4）顶环— stripper ring5）推板— stripper plate6）加速顶— accelerated ejection1．顶出辅助机构Supplementary operating system1）弹簧柱塞器— spring – loaded plunger2）弹珠定位器— ball catch system3）插销式锁扣— Latch – lock4）尼龙拉杆装置— friction puller device2．电器元件Electric Components1）压力传感器— pressure transducer2）限位开关— limit switchF．冷却系统Cooling System1．基本词汇Basic Word1）温差— temperature variation2）水孔（水道）— waterlines, water-ways, flow-way, channel 3）水路— cooling circuit4）水路示意图— water schematic, schematic circuit5）冷却液— coolant, coolant fluid6）内连接— interconnect7）外连接— external connection8）出口、入口— outlet、inlet9）漏水— water leakage2．水路分布Circuits1）阶梯式水路— stepped system2）分隔板水路— baffled hole system3）斜孔式水路— angled hole system3．水路元件Components1）闷头（螺塞、止水栓）—（threadless）brass pressure plug : female plug & male 2）隔水片— baffle3）密封圈— O – ring4）快插水路接头— quick disconnect fitting, quick connection adaptor5）弯头— elbow6）偶合器（连接器、接头）— adaptor (including a plug & a socket)7）橡皮管— rubber hose1）分水板,集水块— water manifoldG．螺纹、螺纹孔& 螺钉Thread, thread hole & screw1．螺纹— thread2．管螺纹— pipe thread3．螺纹孔— screw hole, tapped hole4．起吊孔— handling hole, jack screw hole, eye bolt hole5．螺钉— screw6．内六角螺钉— socket headed cap screw （s.h.c.s.）7．沉头螺钉— flat headed cap screw （f.h.c.s）8．螺栓— bolt9．螺母— nut10．锁紧螺母— locknut11．螺纹标准Thread Standard①公制标准— Metric②英制标准— Imperial③英制管螺纹标准— British Standard Pipe thread （BSP）④美制管螺纹标准— NPT⑤美制粗螺纹标准— United Coarse thread （UNC）⑥美制细螺纹标准— United Fine thread （UNF）H．润滑Lubrication1．润滑槽— grease groove2．加油管— grease line3．油杯— lubrication fittingI. 测量仪器Measuring Instruments1．游标卡尺— vernier caliper2．千分尺— micrometer3．高度规— height gauge4．刻度规— dial gauge5．三坐标测量仪（三次元）—Coordinate Measure Machine （CMM）6．塞规— pin gauge7．圆角量规— radii gauge8．轮廓投影机—profile projectorJ．注塑机参数Injection Machine Parameter1．注塑机规格参数Injection Machine Specification①锁紧类型clamp typea．油缸— hydraulic b．肘杆式— toggle②垂直注塑机导柱间距— tie bar vertical clearance③水平注塑机导柱间距— tie bar horizontal clearance④台板尺寸— platen dim.⑤最小/ 最大模厚— mold height Min. / Max., Min. / Max. mold thickness⑥最小/ 最大注塑机开档— open daylight Min. / Max.⑦锁紧行程— clamp stroke⑧锁紧力— clamping force⑨顶出行程— ejector stroke⑩顶出力— ejector force。
HI-P公司模具专业英语培训——注塑模
模具专业英语培训——注塑模English Training——Injection Mold（一）模具专业基本用词Professional Terms1．塑料—plastic, resin2．样件—sample3．钢料—steel4．注塑机—injection machine, press5．产品—part, product, moulding6．模具—mold, mould, toolA 简易模（样板模）—prototype moldB 量产用模具—production mold 7．三维造型（数模）—model, 3D data8．二维产品图—2D part drawing9．设计—design10．制造—manufacture, build up, construction11．检验—check, inspection12．测量—measure, inspection13．修改—change, modify, correction14．工程更改—engineer change15．质量—quality16．数量—quantity17．基准—datum, reference（二）如何解析2D 产品图？How to read 2D part drawing?一．产品几何Geometry1．点—point2．线（边）—line, edge3．面faceA 侧面—sideB 表面—surfaceC 外观面—appearance surface 4．壁厚—wall thickness, stock thickness5．加强筋（骨位）—rib6．孔—hole7．细长的槽—slot8．柱位—boss9．角—cornerA 圆角—filletB 倒角—chamferC 尖角—sharp corner 10．斜度—angle, taper11. 凹槽—recess , groove二．分模信息Splitting1．分型线—parting line (P/L), splitting line2．主分模方向—main direction, line of draw3．浇口设定—gating三．产品标识Part Identification1．产品名称—part name (P/N)2．产品编号+版本号—part number + revision (Rev.)3．型腔号—cavity number4．材料标记—material symbol5．模具编号—mold number (no.)6．日期印—dating insert, date code7．循环印—cycling code8．公司标志—company logo四．技术要求Specification (Special Requirement)1．项目启动表Kick-off sheet1）项目名称—program name, project name2）产品名称—part name, product name, part description3）产品编号—part number (P/N)4）客户模号—customer mold no.5）项目启动日期—kick off date, start date6）项目完成日期—due date,lead time7）内模件用钢—tool steel8）型腔数量—number of cavities9）数模文件编号—data file no.10）注塑材料—resin, plastic, raw material11）收缩率—shrink, shrinkage, shrink factor12）注塑机吨位—molding machine size, injection machine size 13）成型周期—cycle time14）型腔光洁度—cavity polish15）型芯光洁度—core polish16）皮纹（晒纹）—texture, grain17）拔模斜度—draft angle, removal taper18）注塑件颜色及光泽—molded color & gloss19）模具加工地—manufacturing facility20）热流道供应商—manifold manufacturer, manifold supplier 21）浇口位置—gate location / position22）浇口类型—gate type23）产品标识—stamp information, part identification24）特殊要求—special instructions2．产品质量及外观要求Part Quality & Appearance1）尺寸及公差Dimension & Tolerance①重要尺寸—critical dimension, important dim., key dim.②理论尺寸—nominal dimension③实际尺寸—actual dimension④公差—tolerance⑤公差带—tolerance range⑥尺寸超差—dimension deviation⑦接受（合格）—accept, OK⑧拒绝（不合格）—reject, refuse, obsolete, NG⑨让步接受—concession, special admit⑩返工—re-work2）产品缺陷（较常见）Defects (normal)①缩印—sink mark, shrinkage②飞边—flash, burr③段差—mismatch discrepancy④银丝纹—snake marks, streak⑤弯曲—warpage, distortion⑥打不足（缺料）—short shot⑦熔接线—weld line3．产品外观Part Appearance①产品颜色—part color②产品光泽—gloss③皮纹粒度—grain4．常用词汇、词组及短语Normal Word, Short Sentence1）单边—per side2）双边—both sides3）加入，添加—add, incorporate4）去除，取消—remove, cancel5）满足…的要求，符合，与…要求一致—according to, conform to, satisfy, meet 6）要求，需要—require, need, demand7）确认—be approved, agreed by …8）允许—permit, allow9）在…范围之内—within10）不可以，不允许，禁止—free from, prevent, avoid11）…，除非有另指—…unless otherwise specified12）…或少于—…or less13）自动化运作—automatic operation14）未注尺寸（详细形状）见三维造型Non dimensioned contour (detailed shape) see 3D model.15）分型线上的飞边（披缝）或段差应小于…Burrs and discrepancy on the P/L shall be … or less.五．标题栏Title Block1．产品名称—part name2．图纸编号 + 版本号（索引号）—drawing no. + level (index)3．一般公差[的标准] —general tolerance（三）如何阅读制模标准？How to read tooling standard? 一．模具结构术语Mold Construction TerminologyA．模架Mold Base1．模架量化特征Measurement Feature①长X 宽X 高—Length X Width X Height②模具推高尺寸（模厚）—stack height of mould③模具重量—total weight of mould, mould thickness2．定模底板—front plate, top clamping plate, clamp plate, clamping plate 3．定模板—cavity plate, fixed mould plate, A – plate4．动模板—core plate, moving mould plate, B – plate5．支撑板—support plate, backing plate6．模脚—support blocks, rails, risers, spacer block7．顶杆固定板—retaining plate, ejector retaining plate8．顶板—ejector plate9．动模底板—back plate10．导柱—guide pillar, leader pin, guide pin11．导套—guide bush, leader pin bush12．复位杆—return pin, push-back pin13．弹簧—spring14．撑头—support pillar15．推板导柱、导套—ejection guide pin / bush16．挡钉—stop pin, stop button17．站立脚—standing-off pillars18．标牌—plaque scutcheonB．成型零部件moulding components19．型芯—core20．型腔—cavity21．镶针—core pin22．镶块—insert, split23．滑块—slide, sliding split24．斜顶—lifter, angled-lift splitA 斜顶头—lifter headB 斜顶杆—lifter rod, lifter shaft 25．成型顶杆—moulding face pin, form pinC．浇注系统Feed System1．塑料Mouldinga．主流道—sprueb．分流道runner①主分流道—main runner②二级分流道—branch runner分流道断面形状cross-sectional shape of runner①圆形—full round②半圆形—semicircular③梯形—trapezoidalc．浇口gate常用浇口形式normal gate type :①边缘浇口（J型浇口）—edge gate, J – gate②侧浇口—side gate③潜伏式浇口—sub-gate, cashew gate, subsurface gate, submarine gate④潜伏式二次浇口(隧道式浇口) —tunnel gate onto feeder post⑤点浇口—pin gate⑥直接浇口(主流道型浇口) —sprue gate, direct gate⑦护耳式浇口—tab gated．模腔—impressione．冷料井—cold slug wellf．热流道—hot runner2．模具零件mold componentsa．定位圈—locating ring, location ring, register ringb．浇口套—sprue bushc．挡圈—stop ringd．浇口镶块—gate inserte．热流道板—manifoldf．热嘴—hot dropD．分型面及其锁紧、排气Parting Surface, inter-locking & venting1．分型线—parting line ( P/L )2．镶拼线—bodyline, joint line3．平/ 不平的分型面—flat / non – flat parting surface4．封胶面—shut off surfaces, seal-off surfaces5．擦位—shut off6．碰穿位—kiss-off7．管位—parting line lock8．分型面的释放(避空) —relief of parting surface9．分型面的平衡—balancing of parting surface10．锁紧角度—locking angle11．锁紧力—clamping force12．锁模板—safety strap13．精定位—Interlock, die lock14．困气—air trap15．排气槽—vent, vent slotE．滑块机构Slide1．驱动Actuation①斜导柱—angled pin, horn pin, cam pin②弹簧—spring③油缸—hydraulic cylinder2．制动Detention①滑块固定器—slide retainer②弹簧制动器—spring-loaded detention (plunger)③挡钉、挡板—stop pin, stop plate, slide stop3．导轨—gib, guide strip4．锁紧块（楔紧块）—heel block, locking heel, wedge block, chase block 5．耐磨片—wear plate, wear strip6．压板—retainer7．螺钉—screw8．定位销—dowelF．斜顶机构Lifter1．斜顶头—lifter head2．斜顶杆—lifter rod, lifter shaft3．开口销—split pin4．固定板（压板）—retainer plate5．耐磨片—wear plate6．铜导套—bronze bushing7．衬套—spacer8．导轨—L – gib9．滑动块—slideG．顶出系统Ejection System1．基本词汇Basic Word①顶出行程—ejection stroke②模具开档—daylight③粘模—stick④产品脱模—part is push off from, clear part of mould, separation of part 2．顶板机构Ejector plate assembly①顶板（推板）—ejector plate②顶板固定板—retaining plate③推板导柱—ejector guide pin④推板导套—ejector guide bush⑤撑头—support pillar, pillar support3．复位机构Return System①复位杆（回程杆）—return pin, push – back pin②挡钉—stop pin, stop button③压簧—compressed spring④碟簧— a stack of ―Belleville‖ washers⑤早复位机构—early return system⑥强制复位机构—positive return system4．顶出方法Ejection Techniques1）顶杆顶出—pin ejection2）顶管顶出—sleeve ejection3）顶块顶出—bar ejection4）扁顶顶出—blade ejection5）顶板顶出—stripper ejection6）油缸顶出—hydraulic ejection7）气顶—air ejection8）阀门顶出—valve ejection5．顶出元件Ejection Elements1）拉料杆—sprue puller, sucker pin2）顶杆—ejector pin3）阶梯式顶杆—stepped ejector pin4）顶管—ejection sleeve, sleeve5）扁顶—ejector blade, slabbed off ejector pin6）顶块—stripper bar7）顶环—stripper ring8）推板—stripper plate9）加速顶—accelerated ejection6．顶出辅助机构Supplementary operating system1）弹簧柱塞器—spring – loaded plunger2）弹珠定位器—ball catch system3）插销式锁扣—Latch – lock4）尼龙拉杆装置—friction puller device7．电器元件Electric Components1）压力传感器—pressure transducer2）限位开关—limit switchF．冷却系统Cooling System1．基本词汇Basic Word1）温差—temperature variation2）水孔（水道）—waterlines, water-ways, flow-way, channel3）水路—cooling circuit4）水路示意图—water schematic, schematic circuit5）冷却液—coolant, coolant fluid6）内连接—interconnect7）外连接—external connection8）出口、入口—outlet、inlet9）漏水—water leakage2．水路分布Circuits1）阶梯式水路—stepped system2）喷淋—baffled hole system3）斜孔式水路—angled hole system3．水路元件Components1）闷头（螺塞、止水栓）—（threadless）brass pressure plug : female plug & male 2）隔水片—baffle3）密封圈—O – ring4）快插水路接头—quick disconnect fitting, quick connection adaptor5）弯头—elbow6）偶合器（连接器、接头）—adaptor (including a plug & a socket)7）橡皮管—rubber hose8）分水板—water manifoldG．螺纹、螺纹孔& 螺钉Thread, thread hole & screw1．螺纹—thread2．管螺纹—pipe thread3．螺纹孔—screw hole, tapped hole4．起吊孔—handling hole, jack screw hole, eye bolt hole5．螺钉—screw6．内六角螺钉—socket headed cap screw （s.h.c.s.）7．沉头螺钉—flat headed cap screw （f.h.c.s）8．螺栓—bolt, eye bolt9．螺母—nut10．锁紧螺母—locknut11．螺纹标准Thread Standard①公制标准—Metric②英制标准—Imperial③英制管螺纹标准—British Standard Pipe thread （BSP）④美制管螺纹标准—NPT⑤美制粗螺纹标准—United Coarse thread （UNC）⑥美制细螺纹标准—United Fine thread （UNF）H．润滑Lubrication1．润滑槽—grease groove2．加油管—grease line3．油杯—lubrication fittingI．测量仪器Measuring Instruments1．游标卡尺—vernier caliper2．千分尺—micrometer3．高度规—height gauge4．刻度规—dial gauge5．三坐标测量仪—Coordinate Measure Machine（CMM）6．塞规—pin gauge7．圆角量规—radii gauge8．輪廓投影機—profile projectorJ．注塑机参数Injection Machine Parameter1．注塑机规格参数Injection Machine Specification①锁紧类型clamp typea．油缸—hydraulic b．肘杆式—toggle②垂直注塑机导柱间距—tie bar vertical clearance③水平注塑机导柱间距—tie bar horizontal clearance④台板尺寸—platen dim.⑤最小/ 最大模厚—mold height Min. / Max., Min. / Max. mold thickness⑥最小/ 最大注塑机开档—open daylight Min. / Max.⑦锁紧行程—clamp stroke⑧锁紧力—clamping force⑨顶出行程—ejector stroke⑩顶出力—ejector force2．试模工艺参数Moulding Process Parameter, machine setting①时间Timer（TM）, seca．注塑（充填）时间—filling time, injection timeb．冷却时间—cooling timec．补缩时间—packing timed．保压时间—holding timee．成型周期—cycle time②速率、速度Velocity, %、speed, in/seca．注塑（充填）速度—injection speedb．保压速率—hold pressure velocityc．螺杆转速—screw rotation speed③压力Pressure（Prs.）, psia．注塑压力—injection pressureb．保压压力—hold pressurec．回压（背压）—back pressure④温度Temperature（Temp.）, °Fa．注塑机喷嘴温度—nozzle temp.b．料筒前段、中段、后段温度—barrel front、middle、rear temp.c．模温—mould temp.d．料温—purged resin melt temp.e．空射料温—air shot melt temp.关于注塑成型对产品造成的各种缺陷及解决方法(一)熔接痕熔接痕是由于来自不同方向的熔融树脂前端部分被冷却、在结合处未能完全融合而产生的。
注塑模具用英语单词
组装、冲压、喷漆等专业词汇Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch镑、英寸EMI gasket导电条front plate前板rear plate后板chassis基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试V oltage switch of SPS电源电压接拉键sheet metal parts 冲件plastic parts塑胶件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource department人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |'plein|刨床miller铣床grinder磨床driller??床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice sectionsuperisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skræpid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dein|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓name of a department部门名称administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车forklift叉车pallet栈板glove(s)手套glove(s) with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头sweeper扫把mop拖把vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机production line流水线chain链条槽magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小)cosmetic defect外观不良slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screwthread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位safety安全quality品质delivery deadline交货期cost成本engineering工程die repair模修enterprise plan = enterprise expansionprojects企划QC品管die worker模工production, to produce生产equipment设备to start a press开机stop/switch off a press关机classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products, up-to-grade products良品defective products, not up-to-gradeproducts不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱die change 换模to fix a die装模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cut material,to input落料to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, not qualified不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for 准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位lots of production生产批量steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify修订to switch over to, switch---to throw--over switching over切换engineering, project difficulty工程瓶颈stage die工程模automation自动化to stake, staking, reviting铆合add lubricating oil加润滑油shut die架模shut height of a die架模高度analog-mode device类模器die lifter举模器argon welding氩焊vocabulary for stamping冲压常词汇stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, blockstop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to.to send delinery backto retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑common vocabulary for die engineering模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder文件夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerazation装箱quantity of physical invetory second count 复盘点数量quantity of customs count会计师盘,点数量the first page第一联filed by accounting department for reference会计部存查end-user/using unit(department)使用单位summary of year-end physical inventory bills年终盘点截止单据汇总表bill name单据名称This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedulesheetPCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory differenceanalysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ acceptedparts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板)stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣品质人员名称类QC quality control 品质管理人员FQC final quality control 终点品质管制人员IPQC in process quality control 制程中的品质管制人员OQC output quality control 最终出货品质管制人员IQC incoming quality control 进料品质管制人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 品质工程人员品质保证类FAI first article inspection 新品首件检查FAA first article assurance 首件确认TVR tool verification report 模具确认报告3B 3B 模具正式投产前确认CP capability index 能力指数CPK capability index of process 模具制程能力参数SSQA standardized supplier quality合格供应商品质评估OOBA out of box audit 开箱检查QFD quality function deployment品质机能展开FMEA failure model effectivenessanalysis 失效模式分析8 disciplines 8项回复内容FA final audit 最後一次稽核CAR corrective action request 改正行动要求corrective action report 改正行动报告FQC运作类AQL Acceptable Quality Level 运作类允收品质水准S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ Average Output Quality 平均出厂品质AOQL Average Output Quality Level 平均出厂品质Q/R/S Quality/Reliability/Service 品质/可靠度服务MIL-STD Military-Standard 军用标准S I-S IV Special I-Special IV 特殊抽样水准等级P/N Part Number 料号L/N Lot Number 特采AOD Accept On Deviation 特采UAI Use As It 首件检查报告FPIR First Piece Inspection Report 百万分之一PPM Percent Per Million 批号制程统计品管专类SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计品质管制R Range 全距AR Averary Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR Gauge Reproducibility&Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它品质术语类QCC Quality Control Circle 品质圈QIT Quality Improvement Team 品质改善小组PDCA Plan Do Check Action 计划执行检查总结ZD Zero Defect 零缺点QI Quality Improvement 品质改善QP Quality Policy 目标方针TQM Total Quality Management 全面品质管理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低品质水准RMA Return Material Audit 退料认可QAN Quality Amelionrate Notice品质改善活动ADM Absolute DimensionMeasuremat 全尺寸测量QT Quality Target 品质目标7QCTools 7 Quality Controll Tools品管七大手法通用之件类ECN Engineering Change Notes 工程变更通知(供应商)ECO Engineering Change Order 工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Specification In Process 制程检验规格SOP Standard Operation Procedure制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QC Quality System 品质系统ES Engineering Standarization 工程标准CGOO China General PCE龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司T TAIWAN 台湾IWS International Workman Standard工艺标准ISO International StandardOrganization 国际标准化组织GS General Specification 一般规格CMCS C-China M-ManufactC-Compaq S-Stamping Compaq产品在龙华冲压厂制造作业规范CQCA Q-Quality A-AssemblyCompaq产品在龙华组装厂品管作业规范CQCP P-Painting Compaq产品在龙华烤漆厂品管作业规范部类PMC Production & Material Control生产和物料控制PPC Production Plan Control 生产计划控制MC Material Control 物料控制ME Manafacture Engineering 制造工程部PE Project Engineering 产品工程部A/C Accountant Dept 会计部P/A Personal & Administration 人事行政部DC Document Center 资料中心QE Quality Engineering 品质工程(部)QA Quality Assurance 品质保证(处)QC Quality Control 品质管制(课)PD Product Department 生产部LAB Labratry 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供应商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号其它OEM Original Equipment Manufacture 原设备制造PCE Personal Computer Enclosure 个人电脑外设PC Personal Computer 个人电脑CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大陆PRC People's Republic of China中国大陆U.S.A the United States of America美国A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存I/O Input/Output 输入/输出OK Ok 好NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electry-static Discharge 静电排放5S 希腊语整理,整顿,清扫,清洁,教养ATIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光碟CD-ROM Compact Disk Read-OnlyMemory 只读光碟FDD Floppy Disk Drive 软碟机HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CAV Cavity 模穴CAD Computer Aid Design 计算机辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly Delivery Requitement周出货需求C?T Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间)S/T Standard Time 标准时间P/M Product Market 产品市场3CComputer,Commumcation,Consumerelectronic's 消费性电子5WIHWhen,Where,Who,What,Why,How to5MMan,Machine,Material,Method,Measurement4MIHMan,Materia,Money,Method,Time 人力,物力,财务,技术,时间(资源)SQA Strategy Quality Assurance 策略品质保证DQA Desigh Quality Assurance 设计品质保证MQA Manufacture Quality Assurance制造品质保证SSQA Sales and service QualityAssurance 销售及服务品质保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic Magnetion Inspect高磁测试FMI Frequency Modulatim Inspect高频测试B/M Boar/Molding(flat cable)C/P Connector of PCA/P AssemblySPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Vedio DiskVCD Vdeio Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID ManufacturingCAE Computer AID EngineeringABIOS Achanced Basic in put/outputsystem 先进的基本输入/输出系统CMOS Complemeruary Metoll OxideSemiconductor 互补金属氧化物半导体PDA Personal Digital Assistant 个人数字助理IC Integrated Circuit 集成电路ISA Industry Standard Architecture工业标准体制结构MCA Micro Channel Architecture 微通道结构EISA Extended Industry Standard Architecture 扩充的工业标准结构SIMM Single in-line memory module 单项导通汇流组件DIMM Dual in-line Memory Module 双项导通汇流组件LED Light-Emitting Diode 发光二级管FMEA Failure Mode Effectivenes 失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Calle 排线PCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WPR Weekly Delivery Requirement 周出货要求PPM Parts Per Million 百万分之一TPM Total Production Maintenance 全面生产保养MRP Material Requiremcnt Planning 物料需计划OC Operation System 作业系统TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & Procedune EMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material Size模具技术用语各种模具常用成形方式accurate die casting 精密压铸powderforming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotaryforging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding橡胶成形encapsulation molding 注入成形sandmold casting 砂模铸造extrusion molding 挤出成形shellcasting 壳模铸造foam forming ?泡成形sinter forging烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slushmolding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warmforging 温锻investment casting 精密铸造matcheddie method 对模成形法laminating method 被覆淋膜成形lowpressure casting 低压铸造lost wax casting 脱蜡铸造matchedmould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landed plungermold 有肩柱塞式模具burnishing die 挤光模landed positivemold 有肩全压式模具button die 镶入式圆形凹模loadingshoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louveringdie 百叶窗冲切模composite dies 复合模具manifold die分歧管模具counter punch 反凸模modular mold组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bendingdie 双折冷弯模具extrusion die 挤出模palletizing die叠层模family mold 反套制品模具plastermold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressivedie 顺序模gypsum mold 石膏铸模protable mold手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁)cavity retainer plate 模穴托板centerpin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母coolingspiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejectorleader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finishmachined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘?flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧?goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶?冲头headless punch直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram压射柱塞inlay busher 嵌入衬套inner plunger内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶?lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locatingring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block歧管档块master plate 靠模样板match plate 分型板mold base 塑胶模座mold clamp 铸模紧固夹mold platen 模用板moving bolster换模保持装置moving bolster plate 可动侧模板onepiece casting 整体铸件parallel block 平行垫块paring line分模线。
注塑行业术语
注塑行业术语1，注塑机规格参数Injection Machine Specification①锁紧类型clamp typea．油缸—hydraulicb ．肘杆式—toggle②垂直注塑机导柱间距—tie bar verticalclearance③水平注塑机导柱间距—tie barhorizontal clearance④台板尺寸—platen dim.⑤最小/ 最大模厚—mold height Min./ Max., Min. / Max. mold thickness⑥最小/ 最大注塑机开档—open daylightMin. / Max.⑦锁紧行程—clamp stroke⑧锁紧力—clamping force⑨顶出行程—ejector stroke⑩顶出力—ejector force2，试模工艺参数Moulding Process Parameter, machine setting①时间Timer （ TM ） , seca, 注塑（充填）时间—filling time,injection time b, 冷却时间—cooling timec, 补缩时间—packing timed, 保压时间—holding timee, 成型周期—cycle time②速率、速度Velocity, % 、 speed, in/seca, 注塑（充填）速度—injection speedb, 保压速率—hold pressurevelocityc, 螺杆转速—screw rotationspeed③压力Pressure （ Prs. ） , psia, 注塑压力—injection pressureb, 保压压力—hold pressurec, 回压（背压）—back pressure④温度Temperature（Temp.）,° Fa, 注塑机喷嘴温度—nozzle temp.b, 料筒前段、中段、后段温度—barrel front 、 middle 、 rear temp.c, 模温— mould temp.d, 料温—purged resinmelt temp.e, 空射料温—air shot melt temp.产品几何Geometry 1．点—point2．线（边）—line, edge 3．面faceA侧面—sideB表面—surfaceC 外观面—appearance surface4．壁厚—wall thickness, stock thickness 5．加强筋（骨位）—rib6．孔—hole7．细长的槽—slot8．柱位—boss9．角— cornerA 圆角—filletB 倒角—chamferC 尖角—sharp corner10 ．斜度—angle, taper11.凹槽—recess , groove一．分模信息Splitting1．分型线—parting line (P/L), splitting line 2．主分模方向—main direction, line of draw 3．浇口设定—gating二．产品标识Part Identification1．产品名称—part name (P/N)2．产品编号 + 版本号—part number + revision (Rev.) 3．型腔号—cavity number4．材料标记—material symbol5．模具编号—mold number (no.)6．日期印—dating insert, date code7．循环印—cycling code8．公司标志—company logo三．技术要求Specification (SpecialRequirement)1．项目启动表Kick-off sheet1）项目名称—program name, project name2）产品名称—part name, product name, partdescription 3）产品编号—part number (P/N)4）客户模号—customer mold no.5）项目启动日期—kick off date, start date6）项目完成日期—due date, lead time7）内模件用钢—tool steel8）型腔数量—number of cavities9）数据文件编号—data file no.10 ）注塑材料—resin, plastic, raw material11 ）收缩率—shrink, shrinkage, shrink factor12 ）注塑机吨位—molding machine size, injectionmachine size13 ）成型周期—cycle time14 ）型腔光洁度—cavity polish15 ）型芯光洁度—core polish16 ）皮纹（晒纹）—texture, grain17 ）拔模斜度—draft angle, removal taper18 ）注塑件颜色及光泽—molded color & gloss19 ）模具加工地—manufacturing facility20 ）热流道供应商—manifold manufacturer, manifoldsupplier21 ）浇口位置—gate location / position22 ）浇口类型—gate type23 ）产品标识—stamp information, partidentification24 ）特殊要求—special instructions2．产品质量及外观要求Part Quality & Appearance Requirement1 ）尺寸及公差Dimension & Tolerance①重要尺寸—critical dimension, important dim., key dim.②理论尺寸—nominal dimension③实际尺寸—actual dimension④公差—tolerance⑤公差带—tolerance range⑥尺寸超差—dimension deviation⑦接受（合格）—accept, OK⑧拒绝（不合格）—reject, refuse, obsolete, NG⑨让步接受—concession, special admit ⑩返工— re-work2）产品缺陷（常见的）Defects (normal)①缩水—sink mark, shrinkage②飞边，毛边—flash, burr③段差—mismatch discrepancy④银丝纹，蛇纹—snake marks, streak⑤弯曲，变形—warpage, distortion⑥打不饱（缺料）—short shot⑦熔接线—weld line⑧多胶—unwanted plastic⑨拉伤— damage3．产品外观Part Appearance①产品颜色—part color②产品光泽—gloss③皮纹粒度—grain4．常用词汇、词组及短语Normal Word, Short Sentence1）单边— per side2）双边— both sides3）加入，添加—add, incorporate4）去除，取消—remove, cancel5）满足的要求，符合，与要求一致—according to, conform to, satisfy, meet6）要求，需要—require, need, demand7）确认— be approved, agreed by8）允许— permit, allow9）在范围之内—within10 ）不可以，不允许，禁止—free from, prevent, avoid11 ），除非有另指—unless otherwise specified12 ）或少于—or less13 ）自动化运作—automatic operation14 ）未注尺寸（详细形状）见三维造型Non dimensioned contour(detailed shape) see 3D model.15 ）分型线上的飞边（披缝）或段差应小于Burrs or discrepancy onthe P/L shall be or less.四．标题栏Title Block产品名称—part name1．图纸编号+ 版本号（索引号）—drawing no. + level (index) 2．一般公差—general tolerance常用注塑术语中英文对照表注塑参数Injection parameter注射量计量行程余料量Injection rate Screw back position Cushion防诞量螺杆转速塑化量预塑背压注射压力保压压力注射速度Sucking back rateScrew speedPlastic rateScrew back pressureInjection pressureholding pressure/packing pressure Injection speed/velocity合模参数合模力合模速度合模行程开模力开模速度开模行程顶出压力顶出速度顶出行程Clamping parameter Clamping forceClamping speed/velocity Clamping strokeOpening forceOpening speed/velocity Opening positionEjector advance pressure Ejector advance speed/velocity Ejector advance position温控参数烘料温度Temperature parameterDry resin material temperature料筒喷嘴温度模具温度油温Cylinder temperature nozzle temperature Mold temperature Oil temperature成型周期循环周期冷却时间注射时间保压时间Molding cycleCycle timeCool timeInjection time Holding pressure time塑化时间顶出停留时间低压保护时间Plant time Knocking out time delay timeMold protect time。
注塑专业英语
Surface Appearance外观Glossiness/gloss finish光洁度Matt finish/matt surface毛面Glass fiber rich surface/glass emergence on the surface 玻纤外露Blooming/surface blooming表面析出White patches on surface表面白斑Silver marks/silver streak银纹Splay mark水纹Flow mark流纹Weld line溶结纹Brittle/brittleness脆Bubbles/trapped gas气泡V oid孔Burn marks烧伤FR failed阻燃不合格Flame rating V-2阻燃V-2Poor dispersion分散不好FR/PTFE …agglomerates etc阻燃剂/PTFE…结块Pellet porous粒子不密/蜜蜂窝Low impact/tensile etc物理性能低High flow/filler content etc流动性/填充…过高Longs/fines/doubles长粒/碎屑/连粒Poor cut粒形不好Bristle/voids表面有小气泡/孔Glass bundles玻纤结团Product was rejected due to产品不能接受因为…High moisture level高水分Warpage/warped翘曲Shrinkage/shrink收缩Sink marks缩影Short shot/short molding打不满Distortion变形Over dimension尺寸过大Under dimension尺寸过小Flashing飞边Discoloration变色Off color颜色差异Flow rate流动率Viscous粘High flow高流动Low flow低流动Sticky粘Mold release脱模Antioxidant抗氧剂Flame retardant agent阻燃剂Heat stabilizer热稳定剂Chopped glass fiber短切玻纤Roving glass fiber粗纱/长玻纤Glass beads玻璃微珠Milled fiber碾磨纤Molybdenum disulfide/moly/MoS2 二硫化钼Colorant着色剂Pigment颜料Dye染料Accepted product specification接受产品规格Approved our product认可我们的产品Re-set spec重新定标准Add in extra …添加多一点…Reduced … content减少…含量Dr opped/reduced … by x％减少…含量…％Confirmed color standard确认颜色标准Approved color standard认可颜色标准Re-confirmed color standard重新确认颜色标准Qualified our product认可我们的产品Undergoing heat aging test在做热老化实验Product is under testing产品在测试当中Received first order接了第一个定单Expected to finish by …预计在…完成Expected order is xMT预计定单量…吨Estimated annual/monthly consumption 预计年/月用量air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁)cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模？die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧？goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶冲头headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块master plate 靠模样板match plate 分型板mold base 塑胶模座mold clamp 铸模紧固夹mold platen 模用板moving bolster 换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paring line 分模线parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pilot pin 导pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 托料板return pin 回位梢riding stripper 浮动脱模器ring gate 环型浇口？roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide(slide core) 滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架spindle 主轴sprue 注道sprue bushing 注道衬套sprue bushing guide 注道导套sprue lock bushing 注道定位衬套sprue puller 注道拉料spue line 合模线square key 方键square nut 方螺帽square thread 方螺纹stop collar 限位套stop pin 止动梢stop ring 止动环stopper 定位停止梢straight pin 圆柱stripper bolt 脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱support pin 支撑梢supporting plate 托板sweep templete 造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝模板plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印extension dwg展开图procedure dwg工程图die structure dwg结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量三、模具塑料模具mould of plastics 注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plate Top plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板support plate方铁spacer plate 底针板ejector plate面针板ejector retainer plate回针Return pin导柱Guide pin有托导套Shoulder Guide bush直导套Straight Guide bush动模座板Bottom clamp plate Moving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould 动模movable mould, movable half上模upper mould，upper half下模lower mould，lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具three plate mould脱模ejection换模腔模具interchangeable cavity mould脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine一、组织机构及职位二、X X电子有限公司XX Electronics CO., Ltd三、总经理办公室General manager’s office四、企管部Enterprise management department (EM)五、行政部Administration department (AD)六、销售部Sales department (SD)七、财务部Financial department (FD)八、技术部Technology department (TD)九、物控部Production material control department(PMC)十、生产部Production department(PD)十一、模具部Mold manufacturing department, Tooling manufacturing department (TM)十二、品管部Quality Assurance department (QA) 十三、冲压车间Stamp workshop, press workshop 十四、注塑车间injection workshop十五、装配车间Assembly workshop十六、模具装配车间Mold and die Assembly workshop 十七、金属加工车间metal machine workshop十八、电脉冲车间Electric discharge process workshop十九、线切割车间wire cutting process workshop 二十、工磨车间Grinding workshop二十一、总经理General manager (GM)二十二、副总经理Vice-general manager二十三、经理manager二十四、董事长president二十五、副董事长Vice-president二十六、XX部门经理Manager of XX department二十七、主任、主管supervisor二十八、拉长Line leader二十九、组长Foreman, forelady三十、秘书secretary三十一、文员clerk三十二、操作员operator三十三、助理assistant六．物控保质期shelf lifeABC分类法ABC Classification反常需求Abnormal Demand措施信息Action Message活动报告标志Action-report-flag基于活动的成本核算Activity-based Costing (ABC) 实际能力Actual Capacity实际成本Actual Costs调整现有库存量Adjust-on-hand已分配量Allocation替代工序Alternative Routine装配订单Assembly Order装配零件表Assembly Parts List装配Assembly计划自动重排Automatic Rescheduling可达到库存Available Inventory可用材料Available Material达到库存Available Stock可利用工时Available Work可签约量Available-to-promise平均库存Average Inventory欠交订单Back Order倒序计划Back Scheduling倒冲法Back flush未完成订单Backlog现有库存余额Balance-on-hand Inventory批号Batch Number批量生产Batch Production标杆瞄准Benchmarking工时清单Bill of Labor提货单Bill of Lading物料清单Bill of Material分库Branch Warehouse经营规划Business Plan采购员Buyer能力管理Capacity Management能力需求计划Capacity Requirements Planning (CRP) 保管费率Carrying Cost Rate保管费Carrying Cost单元式制造Cellular Manufacturing修改批量日期Change Lot Date修改工序Change Route修改产品结构Change Structure检查点Check Point闭环物料需求计划Closed Loop MRP通用工序标识Common Route ID计算机集成制造Computer-integrated Manufacturing (CIM)配置代码Configuration Code约束管理/约束理论Constraints Management/Theory of Constraints (TOC)依成本的材料清单Costed Bill of Material急需零件Critical Part累计提前期Cumulative Lead Time现有运转时间Current Run Hour现有运转数量Current Run Quantity周期盘点Cycle Counting调整日期Date Adjust有效日期Date Available修改日期Date Changed结束日期Date Closed截止日期Date Due生产日期Date in Produced库存调整日期Date Inventory Adjust作废日期D ate Obsolete收到日期Date Received交付日期Date Released需求日期Date Required发货日期Date to Pull空负荷Dead Load需求管理Demand Management需求Demand实际能力Demonstrated Capacity非独立需求Dependent Demand直接增减库存处理法Direct-deduct Inventory Transaction Processing发料单Disbursement List派工单Dispatch List分销资源计划Distribution Resource Planning (DRP) 鼓－缓冲－绳子Drum-buffer-rope经济订货批量Economic Order Quantity (EOQ)工程变更生效日期Engineering Change Effect Date工程变更生效单Engineering Change Effect Work Order工程停止日期Engineering Stop Date例外控制Exception Control呆滞材料分析Excess Material Analysis急送代码Expedite Code加工订单Fabrication Order补足欠交Fill Backorder总装提前期Final Assembly Lead Time 确认的计划订单Firm Planned Order固定订货批量F ixed Order Quantity集中预测Focus Forecasting完全跟踪Full Pegging通用生产管理原则Generally Accepted Manufacturing Practices毛需求Gross Requirements在制品库存In Process Inventory独立需求Independent Demand投入/产出控制Input/ Output Control检验标识Inspection ID厂际需求Interplant Demand库存周转率Inventory Carry Rate仓库库位类型Inventory Location Type库存周转次数Inventory Turnover发送订单Issue Order项目记录Item Record物料项目Item加工车间Job Shop准时制生产Just-in-time (JIT)看板Kanban人工工时Labor Hour最后运输日期Last Shipment Date提前期Lead Time层Level负荷量Load Leveling负荷报告Load Report负荷Load仓位代码Location Code仓位备注Location Remarks仓位状况Location Status按需订货Lot for Lot批量标识Lot ID批量编号Lot Number批量Lot Size低位码Low Level Code机器能力Machine Capacity机器加载Machine Loading外购或自制决策Make or Buy Decision面向订单生产的产品Make-to-order Product面向库存生产的产品Make-to-stock Product制造周期时间Manufacturing Cycle Time制造资源计划Manufacturing Resource Planning (MRP II)主生产计划Master Production Schedule (MPS)物料成本Material Cost物料发送和接收Material Issues and Receipts物料需求计划Material Requirements Planning (MRP) 登陆标志MPS Book Flag MPS多重仓位Multiple Location净改变式MRP N et Change MRP净需求Net Requirements新仓位New Location新组件New Parent新仓库New Warehouse不活动报告No Action Report现有库存量On-hand Balance未结订单Open Order订单输入Order Entry订货点Order Point订货方针Order Policy订货承诺Order Promising订货备注Order Remarks双亲Parent零件清单Part Bills零件批次Part Lot零件编号Part Number零件Part反查Pegging领料单Picking List领料/提货Picking计划订单Planned Order后减库存处理法Post-deduct Inventory Transaction Processing前减库存处理法Pre-deduct Inventory Transaction Processing发票价格Price Invoice采购订单价格Price Purchase Order优先计划Priority Planning产品控制Product Control产品线Production Line生产规划编制Production Planning产品率Production Rate产品结构树Production Tree预计可用库存Projected Available Balance采购订单跟踪Purchase Order Tracking已分配量Quantity Allocation仓位数量Quantity At Location欠交数量Quantity Backorder完成数量Quantity Completion需求量Quantity Demand毛需求量Quantity Gross进货数量Quantity In排队时间Queue Time队列Queue重生成式MRP Regenerated MRP重排假设Rescheduling Assumption资源需求计划Resource Requirements Planning粗能力计划Rough-cut Capacity Planning工艺路线Routing安全库存量Safety Stock保险期Safety Time预计入库量Scheduled Receipt残料率Scrap Factor发送零件Send Part维修件Service Parts发货地址Ship Address发货单联系人Ship Contact发货零件Ship Date发货单Ship Order 工厂日历Shop Calendar车间作业管理Shop Floor Control损耗系数Shrinkage Factor标准产品成本Standard Product Cost标准机器设置工时Standard Set Up Hour标准单位运转工时Standard Unit Run Hour标准工资率Standard Wage Rate状况代码Status Code库存控制Stores Control建议工作单Suggested Work Order约束理论Theory of Constraints (TOC)时间段Time Bucket时界Time Fence单位成本Unit Cost采购计划员Vendor Scheduler采购计划法Vendor Scheduling工作中心能力Work Center Capacity工作中心Work Center在制品Work in Process工作令跟踪Work Order Tracking工作令Work Order工作进度安排Work Scheduling零库存Zero Inventories经济订货批量＝Squat(2*年订货量*平均一次订货准备所发生成本/每件存货的年储存成本)美国生产和库存控制协会APICS，American Production & Inventory Control Society三十四、产品三十五、连接器connector三十六、端子terminal三十七、条型连接器bar connector三十八、阴连接器Housing三十九、阳连接器wafer四十、线束wire harness四十一、间距space四十二、额定电压rated voltage四十三、额定电流rated current四十四、接触电阻contact resistance四十五、绝缘电阻insulation resistance四十六、超声波焊接ultrasonic welding四十七、耐压withstand voltage四十八、针pin四十九、物料编号part number五十、导线wire五十一、基体金属Base metal五十二、电缆夹cable clamp五十三、倒角chamfer五十四、接触面积contact area五十五、接触件安装孔contact cavity五十六、接触长度contact length五十七、接触件电镀层contact plating五十八、接触压力contact pressure五十九、接触件中心距contact space六十、接触簧片contact spring六十一、插孔socket contact六十二、法兰、凸缘Flange六十三、界面间隙interfacial gap六十四、键Key六十五、键槽keyway六十六、过渡段ramp六十七、屏蔽套shielding六十八、定位基准Datum reference六十九、扁平电缆flat cable ，Ribbon cable七十、柔性印刷电线Flexible printed wiring七十一、多层印制电路Multilayer printed circuit七十二、焊盘pad七十三、图形pattern七十四、间距pitch七十五、负极Negative pole七十六、正极positive pole七十七、回流Reflow七十八、原理图Schematic diagram七十九、单面板single sided board八十、双面板Two-sided board，Double-sided board 八十一、表面安装surface Mounting八十二、翘曲warp，bow八十三、波峰焊wave soldering八十四、编织层braid八十五、同轴电缆coaxial cable八十六、电介质dielectric八十七、电缆中导线的头数ends八十八、外部干扰external interference八十九、填充物filler九十、护套jacket九十一、比重specific gravity九十二、电阻的温度系数Temperature coefficient of resistance九十三、品管九十四、SPC statistic process control九十五、品管保证Quality Assurance九十六、品管控制Quality control九十七、来料检验IQC Incoming quality control九十八、巡检IPQC In-process quality control九十九、校对calibration百、动态试验dynamic test百一、环境试验Environmental test百二、非破坏性试验non-destructive test百三、光泽gloss百四、击穿电压(dielectric) breakdown voltage百五、拉伸强度tensile strength百六、冷热骤变试验thermal shock test百七、环境试验炉Environmental chamber百八、盐雾实验salt spray test百九、绝缘电阻测试验仪Insulating resistance meter百十、内应力internal stress百十一、疲劳fatigue百十二、蠕变creep百十三、试样specimen百十四、撕裂强度tear strength 百十五、缩痕shrink mark, sink mark百十六、耐久性durability百十七、抽样sampling百十八、样品数量sample size百十九、AQL Acceptable Quality level百二十、批量lot size百二十一、抽样计划sampling plan百二十二、OC曲线operation curve百二十三、试验顺序sequence of tests百二十四、环境温度ambient temperature百二十五、可焊性solderability百二十六、阻燃性flame resistance百二十七、生产百二十八、注塑机injection machine百二十九、冲床Punch machine百三十、混料机blender mixer百三十一、尼龙nylon百三十二、黄铜brass百三十三、青铜bronze百三十四、紫(纯)铜copper百三十五、料斗hopper百三十六、麻点pit百三十七、配料compounding百三十八、涂层coating百三十九、飞边flash百四十、预热preheating百四十一、料reworked material百四十二、塑料reworked plastics百四十三、工艺设计process design百四十四、紧急停止emergency stop百四十五、延时time delay七．QS-9000中的术语APQP Advanced Product Quality Planning and Control Plan，产品先期策划和控制计划PPAP Production Part Approval Process,生产件批准程序FMEA Potential Failure Mode and Effects Analysis,潜在失效模式及后果分析Injection machine 啤机Shot size（weight）实际射胶量injection volume 理论射胶量min mold height 最小容模厚度Max mold height 最大容模厚度Tie bar clearance 拉杆间距Die plate size 模板尺寸Ejector stroke 顶出行程barrel 炮筒，机筒clamp force 锁模力non-return valve 止回阀shear 剪切opening 开模行程Injection pressure 射胶压力back pressure 背压nozzle size 射咀尺寸Cycle time 循环周期down time 停机时间hopper 料筒Mold release 脱模剂lubrication 润滑work horse 主力，主要设备Reserve pressure/packing pressure保压mold trial 试模shot （一）啤Decompress 减压oven 烤炉，烘灶shrinkage rate 收缩率Residence time 滞留时间injection speed 注射速度booster time 增压时间Compression ratio 压缩比mold close time 合模时间Resin 胶料Plastification 塑化，增塑viscosity 粘性，粘度contamination 污染，杂物Thermoplastic 热塑性塑料thermosetting plastics 热固性塑料Booster time 增压时间feed 喂料，填充purge 净化Flame retardant 阻燃degradation 降解，软化regrind 再粉碎Water absorption 吸水reinforce 增强，加固specific gravity 比重Elongation 延伸率density 密度melting point 熔点Polystyrene 聚苯乙烯（PS）Styrene 苯乙烯Acrylonitrile 丙烯腈Polypropylene 聚丙烯（PP）Polyethylene 聚乙烯glass fiber 玻纤Condensation 凝固，浓缩crystalline resin 结晶形塑料Mold materials 模具General-purpose steel 多用途钢tool steel 模具钢Free-cutting steel 高速切削钢case hardening steel 表面硬化钢Pre-hardened steel 预硬钢ball and roller bearing steel 滚珠轴承钢Nonferrous steel 非铁合金high speed steel 高速钢cast iron 铸铁Steel specification 钢材规格steel certification 钢材合格证明书Stainless steel 不锈钢nickel 镍chrome 铬aluminum 铝Copper 铜brass 黄铜bronze 青铜titanium 钛Processing 钢材的加工方法Harding / quench 淬火nitride 氮化temper 回火anneal 退火Roll 轧制abrasive 研磨，磨损的finish 精加工，抛光（polish）Case-hardening 表面硬化milling machine 铣（锣）床Lathe车床drill 钻床wire cut 线割NC(numerical control ) 数控材料EDM (Electrical discharge machine) 电火花加工Cut steel 开料Precision ground 精密研磨heat treatment 热处理tap 丝锥，攻牙Texture 蚀纹weld 焊接forge 锻压deformation 变形Spraying 喷涂die-cast 压铸Properties 性能Resistance 电阻，抵抗能力abrasion / wear磨损erode / corrode 腐蚀Toughness 韧性yield strength 屈服强度tensile strength 拉伸强度Fatigue strength 疲劳强度break 断裂stress 应力hardness 硬度Humidity / moisture 潮湿，湿气roughness 粗糙度parameter 参数Thermal conductivity 导热系数manufacture 制造，加工drawback 缺点Ductility 延展性grain 晶粒property 性能，财产brittleness 脆性GD&T （Geometric Dimensions and Tolerance ）形位尺寸公差Flexural strength 挠曲强度impact 冲击conductivity 传导性，导电性Optical 光学的transparent 透明的insulation 绝缘Mechanical 机械的processability 可加工性能timeyield 蠕变Physical 物理的flow rate 流动速率compressive strength 压缩强度Adhesive 粘附的，胶合durability 耐用性Mold design 模具设计Tooling specification 模具规格mould flow 流动模拟sprue nozzle 唧咀孔Clearance 避空，间隙undercut 倒扣flush 插入，埋入legend 图例Groove 凹槽latch 插销class 类型，种类plan 平面图Orifice 孔，口column 柱位boss 凸台standard 标准，规格Rib 骨位tapered interlock 锥形管位块Bubbler 炮隆Bolt 螺钉，销顶identification mark 铭牌P/L strip 锁模片Overflow well / cold-slug well 冷料井Vent 排气pocket 槽Gate location 入水点full line 实线broken line 虚线Retainer 固定，支撑operator 操作者（啤工）receptacle 插座Lifting hole 吊令孔insulation plate 隔热板cavity number 型腔号Bolster 支撑，垫子vent channel 排气槽leak / filter 渗漏Leak test 试运水stamp / engrave 雕刻，印记（打字唛）Clamp slot 码模槽support button / pin 垃圾钉cut steel 开料Lodge 安装，放置inlay 镶嵌，插入cam / lifter 斜顶Stripper推方lifting bar 吊模方sprue 唧咀tolerance 公差Counter bore 沉孔slant 倾斜，斜面conical 圆锥的，圆锥形的Bolt 螺栓manifold 热流道板prototype tooling 原型试验Gusset 角撑reverse mold 倒装模constrain / restrict约束，限制Counter lock 反锁thermocouple 热电偶moldmaker 模具制造商Asset / property number 资产编号tool product destination 模具生产地点Accelerating ejection 加速顶出hydraulic 液压的pneumatic 气动的Trapezoid 梯形的semi-round 半圆形format 格式baffle 隔水片Electrode 电极，铜公spare part 配件gall 磨伤，插伤Cable 电缆，电线plating / coating （电）镀bonding / joint 接头Wall transition 壁厚过渡Product problem 产品问题Troubleshoot 故障处理reduce(add) plastic 减（加）胶Burr/flash披峰Burn mark 烧焦ejector mark 顶针印，顶白black specs 黑点，黑斑Discoloration 混色，污点gloss 光泽jetting/worming 走水纹Sink mark 缩水void / bubble 气泡，夹气distortion 变形Warpage 翘曲short molding / non-fill缺胶，未走齐Weld line / knit line 夹水线discarded as useless 报废Split line 夹线stick in sprue bushing / cavity / core 粘唧咀/前模/后模Break / crack 顶裂brittleness 脆性，易脆Others 其他Invoice 发票，清单vendor(er) 卖方vendee 买方guideline 方针，指导Intricate 复杂的confidential 机密的，不可外泄的proprietary 私有的Authorize 批准，授权recipient 接收者issue ①发布，提供；②问题Approve 确认，赞成requirement 需要，必需物const 常数，常量Regarding 关于，涉及opposite 相反的，对面的latitude 纬度，纵向的Version 版本definition 注释，解说transversal 横向的，截线Profile 轮廓，剖面eliminate / cancel 取消allow / permit 允许，许可Respective 各自的，分别的individual 单独的decrease 减少increase 增加Preliminary 初步的approximately 大约，近似estimate / valuate估计，预算Adjust 调整，校准application 应用，申请maintain 维持Accurate / precise 精确的smooth 光滑，顺畅的device 装置，设备Convenient 方便的deadline 截至日期available 有用的，有空的Shift 轮班，换班critical 关键的，临界的exceptional 异常的，优异的Exceed 超过layout 布局，方案loss 损失，消耗install 安装，安置Rotation 旋转item 条款，项目quotation 报价stabilize 稳定Quality 质量quantity 数量couple 连接，接合configuration 构造，外形Illustrate 图解说明simulation 模拟，仿真recommend 推荐使用。
模具专业英语——注塑模
Injection Mold Technical Terms特克内克腾目思（一）模具专业基本用词 Professional Terms Intensification Factor 增强比Scientific molding 科学注塑英腾次分克深发克偷塞音特菲克计数器counter康特Specific Injection Pressure (Psi)特殊注塑压力思呗色服克1．塑料—plastic, resin瑞申油管：Oil pipe 尼龙--------nylon2．样件—sample 调节板-------adjust plate3．钢料—steel A板--------a plate4．注塑机—injection machine, press 定位圈----locating ring 喽客厅令5．产品—part, product, moulding 斜导柱-----angular pin 安给拉PIN6．模具—mold, mould, tool B板--------- b plateA 简易模（样板模）—prototype moldB 量产用模具—production mold7．三维造型（数模）—3D model, 滚珠导套-------ball ejector bush8．二维产品图—2D part drawing 拽应扁顶针--------blade ejector pin 布累得9．设计—design 低赛应下模板--------bottom clamping plate 抱腾10．制造—manufacture, 上模型腔------cavity main insert11．检验—check, 上模镶件------cavity sub insert12．测量—measure, 妹试司筒针--------center pin 深特13．修改—change, modify 下模型芯------core main insert14．工程更改—engineer change 下模镶针------core pin15．质量—quality 快乐体下模镶件------core sub insert16．数量—quantity 宽体踢延迟顶针-------delay ejector pin17．基准—datum, reference 拉杆限位钉--------distance bolt（二）如何解析2D 产品图？How to read 2D part drawing?一．产品几何Geometry 顶距限位柱--------distance spacer1．点—point 销钉-------dowel pin2．线（边）—line, edge 顶块--------ejector bar3．面face 顶板导套-----ejector leader pinA 侧面—side塞得 B表面—surface射飞思 C 外观面—appearance surface安皮尔思射飞思4．壁厚—wall thickness 我射克来思顶板导柱----ejector leader pin李德拼5．加强筋（骨位）—rib 瑞布顶针-------ejector pin6．孔—hole后顶针地板------ejector plate7．细长的槽—slot 顶针面板-----ejector retain plate 瑞腾8．柱位—boss 抱死顶棍------ejector rod9．角—corner 司筒------ejector sleeveA 圆角—filletB 倒角—chamferC 尖角—sharp corner10．斜度—angle, taper 平头螺丝------F.H.S11. 凹槽—recess , groove 固定块--------fix block二．分模信息Splitting 固定上模-------fixing half1．分型线—parting line 浇口镶件------gate insert2．主分模方向—main direction, line of draw 滑块压板-----guide rail3．浇口设定—gating 无头螺丝-----H.S.S三．产品标识Part Identification 热流道--------hot runner1．产品名称—part name (P/N) 隔热板------insulate plate 因修累特2．产品编号+版本号—part number + revision (Rev.) 导套-----leader bushing 李得报圣个3．型腔号—cavity number 导柱------leader pin4．材料标记—material symbol 斜顶-----lifter body5．模具编号—mold number (no.) 吊环-------lifter eye bolt6．日期印—dating insert, date code 斜顶导向块-----lifter guide7．循环印—cycling code 斜顶滑块------lifter slider8．公司标志—company logo 斜顶耐磨板------lifter wear plate四．技术要求Specification (Special Requirement) 限位开关------limit switch1．项目启动表Kick-off sheet 支撑柱-----MB stand1）项目名称—program name, project name 模架--------mbase2）产品名称—part name, product name, part description 动模（下模）-----move half 3）产品编号—part number (P/N) o型圈-------o ring4）客户模号—customer mold no. 油管接头--------oil nipple5）项目启动日期—kick off date, start date 锁紧扣------parting lock6）项目完成日期—due date,lead time 水堵头------pipe plug7）内模件用钢—tool steel 拉杆----puller bolt8）型腔数量—number of cavities 流道换向针------puller insert9）数据文件编号—data file no. 拉料针-----puller plate10）注塑材料—resin, plastic, raw material 定位拉板-------puller plate11）收缩率—shrink, shrinkage, shrink factor 回针------return pin12）注塑机吨位—molding machine size, injection machine size13）成型周期—cycle time 流道板--------runner stripper plate14）型腔光洁度—cavity polish 内六角螺丝------S.H.C.S.15）型芯光洁度—core polish 锁模块-------safety block16）皮纹（晒纹）—texture, grain 台阶螺丝------shoulder screw17）拔模斜度—draft angle, removal taper 快速接头-----shut off nipple18）注塑件颜色及光泽—molded color & gloss 司筒压紧块-----sleeve pin block19）模具加工地—manufacturing facility 滑块------slider body20）热流道供应商—manifold manufacturer, manifold supplier21）浇口位置—gate location / position 滑块底部耐磨板---slider bottom wear plate 22）浇口类型—gate type 斜压块-----slider cam23）产品标识—stamp information, part identification24）特殊要求—special instructions 滑块中心导轨----slider center guide 2．产品质量及外观要求Part Quality & Appearance Requirement1）尺寸及公差Dimension & Tolerance 滑块型芯-----slider insert①重要尺寸—critical dimension, important dim., key dim.②理论尺寸—nominal dimension 滑块镶针------slider pin③实际尺寸—actual dimension 滑块限位板-----slider stopper plate④公差—tolerance 滑块耐磨板----slider top wear plate⑤公差带—tolerance range 方铁-----spacer block⑥尺寸超差—dimension deviation 垫圈------spacer ring⑦接受（合格）—accept, OK 浇口套------sprue bushing⑧拒绝（不合格）—reject, refuse, obsolete, NG 限位挡板---stop plate⑨让步接受—concession, special admit 垃圾钉----stopper disk⑩返工—re-work 精定位----straight lock推板镶件----stripper insert2）产品缺陷（常见的）Defects (normal) 推板--------stripper plate①缩水—sink mark, shrinkage 支撑住-----support pillar②飞边，毛边—flash, burr 上模板------top clamping plate③段差—mismatch discrepancy 压紧块-------wedge block④银丝纹，蛇纹—snake marks, streak 弹簧--------spring⑤弯曲，变形—warpage, distortion 水接头------water nipple⑥打不饱（缺料）—short shot 增加油槽-------add oil groove⑦熔接线—weld line bubbles气泡 shear[☞i☜]n.剪,切多胶— unwanted plastic regulation整顿cleanness清扫 delamination起鳞分层⑧拉伤—damage blinster气泡 flow mark流痕3、产品外观 Part Appearance①产品颜色— part color②产品光泽— gloss③皮纹粒度— grainaberration 色差 atomization ?化bank mark ?料纹 bite 咬入blacking hole 涂料孔(铸疵) blacking cab 涂料疤blister 起泡 blooming 起霜blow hole 破孔 blushing 泛白body wrinkle 侧壁皱纹 breaking-in 冒口带肉bubble 膜泡 burn mark 糊斑burr 毛边 camber 翘曲cell 气泡 center buckle 表面中部波皱check 细裂痕 checking 龟裂chipping 修整表面缺陷 clamp-off 铸件凹痕collapse 塌陷 color mottle 色斑corrosion 腐蚀 crack 裂痕crazing 碎裂 crazing 龟裂 deformation 变形 edge 切边碎片edge crack 裂边 fading 退色filler speak 填充料斑 fissure 裂纹flange wrinkle 凸缘起皱 flaw 刮伤flow mark 流痕 galling 毛边glazing 光滑 gloss 光泽grease pits 污斑 grinding defect 磨痕haircrack 发裂 haze 雾度incrustation 水锈 indentation 压痕internal porosity 内部气孔 mismatch 偏模mottle 斑点 necking 缩颈nick 割痕 orange peel 橘皮状表面缺陷overflow 溢流 peeling 剥离pit 坑 pitting corrosion 点状腐蚀plate mark 模板印痕 pock 麻点pock mark 痘斑 resin streak 树脂流纹resin wear 树脂脱落 riding 凹陷sagging 松垂 saponification 皂化scar 疤痕 scrap 废料scrap jam 废料阻塞 scratch 刮伤/划痕scuffing 深冲表面划伤 seam 裂痕shock line 模口挤痕 short shot 充填不足shrinkage pool 凹孔 sink mark 凹痕skin inclusion 表皮摺叠 straightening 矫直streak 条状痕 surface check 表面裂痕surface roughening 橘皮状表皮皱摺 surging 波动sweat out 冒汗 torsion 扭曲warpage 翘曲 waviness 波痕webbing 熔塌 weld mark 焊痕whitening 白化 wrinkle 皱纹④3．常用词汇、词组及短语Normal Word, Short Sentence1）单边—per side2）双边—both sides3）加入，添加—add, incorporate4）去除，取消—remove, cancel5）满足…的要求，符合，与…要求一致—according to, conform to, satisfy, meet 6）要求，需要—require, need, demand7）确认—be approved, agreed by …8）允许—permit, allow9）在…范围之内—within10）不可以，不允许，禁止—free from, prevent, avoid11）…，除非有另指—…unless otherwise specified12）…或少于—…or less13）自动化运作—automatic operation14）未注尺寸（详细形状）见三维造型Non dimensioned contour (detailed shape) see 3D model.15）分型线上的飞边（披缝）或段差应小于…Burrs or discrepancy on the P/L shall be … or less.五．标题栏Title Block1．产品名称—part name2．图纸编号 + 版本号（索引号）—drawing no. + level (index)3．一般公差—general tolerance（三）如何阅读制模标准？How to read tooling standard? 一．模具结构术语Mold Construction TermsA．模架Mold Base1．模架量化特征Measurement Feature①长X 宽X 高—Length X Width X Height②模具高度尺寸（模厚）—stack height of mould③模具重量—total weight of mould, mould thickness2．定模底板—front plate, top clamping plate, clamp plate, clamping plate 3．定模板—cavity plate, fixed mould plate, A – plate4．动模板—core plate, moving mould plate, B – plate5．支撑板—support plate, backing plate6．间隔板,方铁—support blocks, rails, risers, spacer block7．顶杆固定板—retaining plate, ejector retaining plate8．顶板—ejector plate，bottom clamping plate9．动模底板—back plate10．导柱—guide pillar, leader pin, guide pin11．导套—guide bush, leader pin bush12．复位杆—return pin, push-back pin13．弹簧—spring14．撑头—support pillar15．顶针板导柱、导套—ejection guide pin / bush16．垃圾钉—stop pin, stop button17．模脚—standing-off pillars18．标牌—plaque scutcheonB．成型零部件moulding components19．型芯—core insert20．型腔—cavity insert21．镶针—core pin22．镶块—sub-insert, split23．滑块—slide, sliding split24．斜顶—lifter, angled-lift splitA 斜顶头—lifter headB 斜顶杆—lifter rod, lifter shaft 25．成型顶杆—moulding face pin, form pinC．浇注系统Feed System1．塑料Mouldinga．主流道—sprueb．分流道runner①主分流道—main runner②二级分流道—branch runner分流道断面形状cross-sectional shape of runner①圆形—full round②半圆形—semicircular③梯形—trapezoidalc．浇口gate常用浇口形式normal gate type :①边缘浇口（J型浇口）—edge gate, J – gate②侧浇口—side gate③潜伏式浇口—sub-gate, cashew gate, subsurface gate, submarine gate④潜伏式二次浇口(隧道式浇口) —tunnel gate onto feeder post⑤点浇口—pin gate⑥直接浇口(主流道型浇口) —sprue gate, direct gate⑦护耳式浇口—tab gated．模腔—impressione．冷料井—cold slug wellf．热流道—hot runner2．模具零件mold componentsa．定位圈—locating ring, location ring, register ringb．浇口套—sprue bushc．挡圈—stop ringd．浇口镶块—gate inserte．热流道板—manifoldf．热嘴—hot dropD．分型面及其锁紧、排气Parting Surface, inter-locking & venting 1．分型线—parting line ( P/L )2．镶拼线—bodyline, joint line3．平/ 不平的分型面—flat / non – flat parting surface4．封胶面—shut off surfaces, seal-off surfaces5．擦穿位—shut off6．碰穿位—kiss-off7．管位—parting line lock8．分型面的释放(避空) —relief of parting surface9．分型面的平衡—balancing of parting surface10．锁紧角度—locking angle11．锁紧力—clamping force12．锁模块—safety strap13．精定位—Interlock, die lock14．困气—air trap15．排气槽—vent, vent slotE．滑块机构Slide1．驱动Actuation①斜导柱—angle pin, horn pin, cam pin②弹簧—spring③油缸—hydraulic cylinder2．制动Detention①滑块固定器—slide retainer②弹簧制动器—spring-loaded detention (plunger)③挡钉、挡板—stop pin, stop plate, slide stop3．导轨—gib, guide strip4．锁紧块（楔紧块）—heel block, locking heel, wedge block, chase block 5．耐磨片—wear plate, wear strip6．压板—retainer,gib7．螺钉—screw8．定位销—dowel pinF．斜顶机构Lifter1．斜顶头—lifter head2．斜顶杆—lifter rod, lifter shaft3．开口销—split pin4．固定板（压板）—retainer plate5．耐磨片—wear plate6．铜导套—bronze bushing7．衬套—spacer8．导轨—L – gib9．滑动块—slideG．顶出系统Ejection System1．基本词汇Basic Word①顶出行程—ejection stroke②模具开档—daylight③粘模—stick④产品脱模—part is push off from, clear part of mould, separation of part 2．顶板机构Ejector plate assembly①顶板—ejector plate②顶板固定板—retaining plate③推板—stripper plate④推板导柱—ejector guide pin⑤推板导套—ejector guide bush⑥撑头—support pillar3．复位机构Return System①复位杆（回程杆）—return pin, push – back pin②垃圾钉—stop pin, stop button③压簧—compressed spring④碟簧— a stack o f “Belleville” washers⑤早复位机构—early return system⑥强制复位机构—positive return system4．顶出方法Ejection Techniques1）顶杆顶出—pin ejection2）顶管顶出—sleeve ejection3）顶块顶出—bar ejection4）扁顶顶出—blade ejection5）顶板顶出—stripper ejection6）油缸顶出—hydraulic ejection7）气顶—air ejection8）阀门顶出—valve ejection5．顶出元件Ejection Elements1）拉料杆—sprue puller, sucker pin2）顶杆—ejector pin3）阶梯式顶杆—stepped ejector pin4）顶管—ejection sleeve, sleeve5）扁顶—ejector blade, slabbed off ejector pin6）顶块—stripper bar7）顶环—stripper ring8）推板—stripper plate9）加速顶—accelerated ejection6．顶出辅助机构Supplementary operating system1）弹簧柱塞器—spring – loaded plunger2）弹珠定位器—ball catch system3）插销式锁扣—Latch – lock4）尼龙拉杆装置—friction puller device7．电器元件Electric Components1）压力传感器—pressure transducer2）限位开关—limit switchF．冷却系统Cooling System1．基本词汇Basic Word1）温差—temperature variation2）水孔（水道）—waterlines, water-ways, flow-way, channel3）水路—cooling circuit4）水路示意图—water schematic, schematic circuit5）冷却液—coolant, coolant fluid6）内连接—interconnect7）外连接—external connection8）出口、入口—outlet、inlet9）漏水—water leakage2．水路分布Circuits1）阶梯式水路—stepped system2）分隔板水路—baffled hole system3）斜孔式水路—angled hole system3．水路元件Components1）闷头（螺塞、止水栓）—（threadless）brass pressure plug : female plug & male 2）隔水片—baffle3）密封圈—O – ring4）快插水路接头—quick disconnect fitting, quick connection adaptor5）弯头—elbow6）偶合器（连接器、接头）—adaptor (including a plug & a socket) 7）橡皮管—rubber hose8）分水板,集水块—water manifoldG．螺纹、螺纹孔& 螺钉Thread, thread hole & screw1．螺纹—thread2．管螺纹—pipe thread3．螺纹孔—screw hole, tapped hole4．起吊孔—handling hole, jack screw hole, eye bolt hole5．螺钉—screw6．内六角螺钉—socket headed cap screw （s.h.c.s.）7．沉头螺钉—flat headed cap screw （f.h.c.s）8．螺栓—bolt9．螺母—nut10．锁紧螺母—locknut11．螺纹标准Thread Standard①公制标准—Metric②英制标准—Imperial③英制管螺纹标准—British Standard Pipe thread （BSP）④美制管螺纹标准—NPT⑤美制粗螺纹标准—United Coarse thread （UNC）⑥美制细螺纹标准—United Fine thread （UNF）H．润滑Lubrication1．润滑槽—grease groove2．加油管—grease line3．油杯—lubrication fittingI．测量仪器Measuring Instruments1．游标卡尺—vernier caliper2．千分尺—micrometer3．高度规—height gauge4．刻度规—dial gauge5．三坐标测量仪（三次元）—Coordinate Measure Machine（CMM）6．塞规—pin gauge7．圆角量规—radii gauge8．轮廓投影机—profile projectorJ．注塑机参数Injection Machine Parameter1．注塑机规格参数Injection Machine Specification①锁紧类型clamp typea．油缸—hydraulic b．肘杆式—toggle②垂直注塑机导柱间距—tie bar vertical clearance③水平注塑机导柱间距—tie bar horizontal clearance④台板尺寸—platen dim.⑤最小/ 最大模厚—mold height Min. / Max., Min. / Max. mold thickness⑥最小/ 最大注塑机开档—open daylight Min. / Max.⑦锁紧行程—clamp stroke⑧锁紧力—clamping force⑨顶出行程—ejector stroke⑩顶出力—ejector force2．试模工艺参数Moulding Process Parameter, machine setting①时间Timer（TM）, seca．注塑（充填）时间—filling time, injection timeb．冷却时间—cooling timec．补缩时间—packing timed．保压时间—holding timee．成型周期—cycle time②速率、速度Velocity, %、speed, in/seca．注塑（充填）速度—injection speedb．保压速率—hold pressure velocityc．螺杆转速—screw rotation speed③压力Pressure（Prs.）, psia．注塑压力—injection pressureb．保压压力—hold pressurec．回压（背压）—back pressure④温度Temperature（Temp.）, °Fa．注塑机喷嘴温度—nozzle temp.b．料筒前段、中段、后段温度—barrel front、middle、rear temp.c．模温—mould temp.d．料温—purged resin melt temp.e．空射料温—air shot melt temp.。
注塑模具术语
注塑模具术语Productwasrejecteddueto产品不能接受因为…Highmoisturelevel高水分、高湿度Warpage/warped翘曲/变形Shrinkage/shrink收缩/收缩率Sinkmarks凹陷、缩水Shortshot/shortmolding打不满、欠注Distortion变形Overdimension尺寸过大Underdimension尺寸过小Flashing飞边、披锋、溢边Discoloration变色Offcolor颜色差异Flowrate 流动速率 Viscous/viscosity粘性的、粘的/黏度Highflow高流动Lowflow低流动 Sticky粘的，粘性的 Stickingcore粘后模，粘模芯Stickingsprue粘水口 Stickingcavity粘前模Moldrelease（agent）脱模(剂)Antioxidant抗氧剂Flameretardantagent阻燃剂Heatstabilizer热稳定剂Choppedglassfiber短切玻纤Rovingglassfiber粗纱/长玻纤Glassbeads玻璃微珠Milledfiber碾磨纤Molybdenumdisulfide/moly/MoS2二硫化钼Colorant着色剂Pigment颜料Dye染料 Acceptedproductspecification接受产品规格Approvedourproduct认可我们的产品Re-setspec重新定标准Addinextra…添加多一点…Reduced…content减少…含量Dropped/reduced…byx％减少…含量…％Confirmedcolorstandard确认颜色标准Approvedcolorstandard 认可颜色标准 Re-confirmedcolorstandard重新确认颜色标准Qualifiedourproduct认可我们的产品Undergoingheatagingtest 在做热老化实验Productisundertesting产品在测试当中Receivedfirstorder接了第一个定单Expectedtofinishby…预计在…完成ExpectedorderisxMT预计定单量…吨Estimatedannual/monthlyconsumption预计年/月用量模具方面：Ejectionsystem顶出系统、脱模系统pin顶针、推杆spring 弹簧Gatetype浇口类型sprue主流道runner分流道cavity模腔Spruegate直浇口Pinpointgate点浇口Tabgate护耳浇口Fangate扇形浇口 Tunnelorsubmarinegate潜伏式浇口Jumpgate 跳跃式浇口Diaphragmgate片状浇口 Ringgate环形浇口Thecavityofthemould模腔Heatedcylinder加热料筒Surfacefinish表面光洁度Sinkmark缩水Airtrap困气Gastrapped气体困着，困气void空隙，孔galling烧焦Weldline熔接痕，熔合线Dragmark划伤、脱模痕Scratchmark模具刮花Deformed/warp变形 Ejectornotreturned顶针不回位slide滑块、行位 streak波纹、条纹、色痕delamination分层Jettingmark喷射痕Gatemark浇口痕rib筋、加强筋、骨位boss 凸台、凸起、凸痕 Meltflowlength熔体流线长度Ejectorplate 顶针板Stoppin限位销Pushrod推杆、顶针Pushbackpin复位杆Ejectorguidepin顶针导柱Cold-slug-well冷料井、冷料穴plate模板 Ejectedmark顶痕，顶白nozzle喷嘴 Surfacedefect表面缺陷Airvent排气口 Fillinguneven走胶不平衡、进胶不平衡。
注塑成型专业词汇
注塑成型专业词汇Injection machine 啤机Shot size（weight）实际射胶量injection volume 理论射胶量min mold height 最小容模厚度Max mold height 最大容模厚度Tie bar clearance 拉杆间距Die plate size 模板尺寸Ejector stroke 顶出行程barrel 炮筒，机筒clamp force 锁模力non-return valve 止回阀shear 剪切opening 开模行程Injection pressure 射胶压力back pressure 背压nozzle size 射咀尺寸Cycle time 循环周期down time 停机时间hopper 料筒Mold release 脱模剂lubrication 润滑work horse 主力，主要设备Reserve pressure / packing pressure保压mold trial 试模shot （一）啤Decompress 减压oven 烤炉，烘灶shrinkage rate 收缩率Residence time 滞留时间injection speed 注射速度booster time 增压时间Compression ratio 压缩比mold close time 合模时间Resin 胶料Plastification 塑化，增塑viscosity 粘性，粘度contamination 污染，杂物Thermoplastic 热塑性塑料thermosetting plastics 热固性塑料Booster time 增压时间feed 喂料，填充purge 净化Flame retardant 阻燃degradation 降解，软化regrind 再粉碎Water absorption 吸水reinforce 增强，加固specific gravity 比重Elongation 延伸率density 密度melting point 熔点Polystyrene 聚苯乙烯（PS）.m,k.bn苯乙烯Acrylonitrile 丙烯腈Polypropylene 聚丙烯（PP）Polyethylene 聚乙烯glass fiber 玻纤Condensation 凝固，浓缩crystalline resin 结晶形塑料Mold materials 模具General-purpose steel 多用途钢tool steel 模具钢Free-cutting steel 高速切削钢case hardening steel 表面硬化钢Pre-hardened steel 预硬钢ball and roller bearing steel 滚珠轴承钢Nonferrous steel 非铁合金high speed steel 高速钢cast iron 铸铁Steel specification 钢材规格steel certification 钢材合格证明书Stainless steel 不锈钢nickel 镍chrome 铬aluminum 铝Copper 铜brass 黄铜bronze 青铜titanium 钛Processing 钢材的加工方法Harding / quench 淬火nitride 氮化temper 回火anneal 退火Roll 轧制abrasive 研磨，磨损的finish 精加工，抛光（polish）Case-hardening 表面硬化milling machine 铣（锣）床Lathe车床drill 钻床wire cut 线割NC(numerical control ) 数控材料EDM (Electrical discharge machine) 电火花加工Cut steel 开料Precision ground 精密研磨heat treatment 热处理tap 丝锥，攻牙Texture 蚀纹weld 焊接forge 锻压deformation 变形Spraying 喷涂die-cast 压铸Properties 性能Resistance 电阻，抵抗能力abrasion / wear磨损erode / corrode 腐蚀Toughness 韧性yield strength 屈服强度tensile strength 拉伸强度Fatigue strength 疲劳强度break 断裂stress 应力hardness 硬度Humidity / moisture 潮湿，湿气roughness 粗糙度parameter 参数Thermal conductivity 导热系数manufacture 制造，加工drawback 缺点Ductility 延展性grain 晶粒property 性能，财产brittleness 脆性GD&T （Geometric Dimensions and Tolerance ）形位尺寸公差Flexural strength 挠曲强度impact 冲击conductivity 传导性、导电性Optical 光学的transparent 透明的insulation 绝缘Mechanical 机械的processability 可加工性能timeyield 蠕变Physical 物理的flow rate 流动速率compressive strength 压缩强度Adhesive 粘附的，胶合durability 耐用性Mold design 模具设计Tooling specification 模具规格mould flow 流动模拟sprue nozzle 唧咀孔Clearance 避空，间隙undercut 倒扣flush 插入，埋入legend 图例Groove 凹槽latch 插销class 类型，种类plan 平面图Orifice 孔，口column 柱位boss 凸台standard 标准，规格Rib 骨位tapered interlock 锥形管位块Bubbler 炮隆Bolt 螺钉，销顶identification mark 铭牌P/L strip 锁模片Overflow well / cold-slug well 冷料井Vent 排气pocket 槽Gate location 入水点full line 实线broken line 虚线Retainer 固定，支撑operator 操作者（啤工）receptacle 插座Lifting hole 吊令孔insulation plate 隔热板cavity number 型腔号Bolster 支撑，垫子vent channel 排气槽leak / filter 渗漏Leak test 试运水stamp / engrave 雕刻，印记（打字唛）Clamp slot 码模槽support button / pin 垃圾钉cut steel 开料Lodge 安装，放置inlay 镶嵌，插入cam / lifter 斜顶Stripper推方lifting bar 吊模方sprue 唧咀tolerance 公差Counter bore 沉孔slant 倾斜，斜面conical 圆锥的，圆锥形的Bolt 螺栓manifold 热流道板prototype tooling 原型试验Gusset 角撑reverse mold 倒装模constrain / restrict约束，限制Counter lock 反锁thermocouple 热电偶moldmaker 模具制造商Asset / property number 资产编号tool product destination 模具生产地点Accelerating ejection 加速顶出hydraulic 液压的pneumatic 气动的Trapezoid 梯形的semi-round 半圆形format 格式baffle 隔水片Electrode 电极，铜公spare part 配件gall 磨伤，插伤Cable 电缆，电线plating / coating （电）镀bonding / joint 接头Wall transition 壁厚过渡Product problem 产品问题Troubleshoot 故障处理reduce(add) plastic 减（加）胶Burr/flash披峰Burn mark 烧焦ejector mark 顶针印，顶白black specs 黑点，黑斑Discoloration 混色，污点gloss 光泽jetting/worming 走水纹Sink mark 缩水void / bubble 气泡，夹气distortion 变形Warpage 翘曲short molding / non-fill缺胶，未走齐Weld line / knit line 夹水线discarded as useless 报废Split line 夹线stick in sprue bushing / cavity / core 粘唧咀/前模/后模Break / crack 顶裂brittleness 脆性，易脆Others 其他Invoice 发票，清单vendor(er) 卖方vendee 买方guideline 方针，指导Intricate 复杂的confidential 机密的，不可外泄的proprietary 私有的Authorize 批准，授权recipient 接收者issue ①发布，提供；②问题Approve 确认，赞成requirement 需要，必需物const 常数，常量Regarding 关于，涉及opposite 相反的，对面的latitude 纬度，纵向的Version 版本definition 注释，解说transversal 横向的，截线Profile 轮廓，剖面eliminate / cancel 取消allow / permit 允许，许可Respective 各自的，分别的individual 单独的decrease 减少increase 增加Preliminary 初步的approximately 大约，近似estimate / valuate估计，预算Adjust 调整，校准application 应用，申请maintain 维持Accurate / precise 精确的smooth 光滑，顺畅的device 装置，设备Convenient 方便的deadline 截至日期available 有用的，有空的Shift 轮班，换班critical 关键的，临界的exceptional 异常的，优异的Exceed 超过layout 布局，方案loss 损失，消耗install 安装，安置Rotation 旋转item 条款，项目quotation 报价stabilize 稳定Quality 质量quantity 数量couple 连接，接合configuration 构造，外形Illustrate 图解说明simulation 模拟，仿真recommend 推荐使用。
塑胶模具相关单词
塑胶模具相关单词塑胶模具制造是一种高度复杂的过程，它涉及到许多重要的单词和概念。
下面是一些常见的塑胶模具相关单词和术语。
1. Injection molding: 注塑是一种制造塑胶制品的方法，可以将熔化的塑料加压注入模具中。
2. Mold: 模具是制造塑料零件的关键部件。
它是由钢制成的，具有所需零件的空间和形状。
3. Mold cavity: 模穴是模具中的空间，用于产生塑料零件的形状和大小。
4. Runner: 喷沟是模具中的通道，将塑料流输送到模穴中。
5. Ejector pins: 弹出杆是用于将制成的塑料零件推出模具的元件。
6. Gates: 网门是连接喷沟和模穴之间的口，控制流入模穴的塑料量。
7. Cooling channels: 冷却通道用于使塑料零件快速冷却并凝固。
8. Draft angle: 模具角度是模具中用于方便塑料零件推出的倾斜。
9. Shrinkage: 收缩是塑料零件在制造过程中收缩的现象。
这必须考虑到模具的设计和制造。
10. Undercut: 模具不平整是阻止塑料零件推出模具的部分。
11. Core and cavity: 核心和模穴是模具中的主要组成部分，用于制造塑料零件的空间和形状。
12. Hot runner: 热喷沟是注塑模具中的高科技部件，可以维持均匀的塑料温度和流量。
13. Parting line: 分型线是在模具中连接两个半部分的线，用于分离塑料零件。
14. Overmolding: 上覆盖是一种将塑料材料套在已有塑料零件上的方法，以获得新的外观和功能。
以上是一些常见的塑胶模具相关单词和概念。
了解这些单词和概念是制造高质量塑料零件的关键。
在完成设计之前，建议与资深的塑料模具制造师一起研究，确保您理解和掌握这些重要的概念。
注塑模具专业英语词汇
隔片
dish gate 因 盘 浇口，盘形浇口
形
bottom plate 下 托 板(底板)，下固定 板
bumper 块
block
缓冲
dozzle 辅助浇口
bracket 扥架 ，支 bushing bolck ，
架
lining衬套
ejector guide pin 顶出导梢，中托边
ejector leader busher 顶出导梢衬 套
模具
Main Runner primary runner 流道
， 主
fixed plate
bolster 固定侧模板
die insert 下 模 板 入子
Mould Gate 浇口设计
Design
guide block/insert 块
导
料
dog 头
chuck
爪牙夹
nozzle射嘴
guide plate 板，定位板
plate下滑块板
缘销
runner ejector lower stripper 下 floating punch 浮
set 流道顶出器 脱料板
动冲头
Runner less无浇道
male 模)
die 公 模 ( 凸 folded 块
block 折 弯
runner lock pin 流道拉梢，拉料 钩，分流道拉料杆
plate 压条
plug / socker 塞 子
pre
extrusion
punch 顶挤冲头
prehardened steel 顶硬钢 pre-piercing punch预冲孔冲头
pressure pad 压 料 块
模具专业英语培训——注塑模.doc
模具专业英语培训——注塑模English Training——Injection Mold （一）模具专业基本用词Professional Terms塑料—plastic, resin样件—sample钢料—steel注塑机—injection machine, press产品—part, product, moulding 模具—mold, mould, toolA 简易模（样板模）—prototype moldB 量产用模具—production mold三维造型（数模）—model, 3D data 二维产品图—2D part drawing设计—design制造—manufacture, build up, construction检验—check, inspection测量—measure, inspection修改—change, modify, correction 工程更改—engineer change质量—quality数量—quantity基准—datum, reference（二）如何解析2D 产品图？How to read 2D part drawing?产品几何Geometry 1．点—point2．线（边）—line, edge3．面faceA 侧面—sideB 表面—surfaceC 外观面—appearance surface4．壁厚—wall thickness, stock thickness5．加强筋（骨位）—rib 6．孔—hole7．细长的槽—slot8．柱位—boss9．角—cornerA 圆角—filletB 倒角—chamferC 尖角—sharp corner10．斜度—angle, taper11. 凹槽—recess , groove分模信息Splitting 分型线—parting line (P/L),splitting line主分模方向—main direction, lineof draw浇口设定—gating产品标识Part Identification产品名称—part name (P/N)产品编号+版本号—part number+ revision (Rev.)型腔号—cavity number材料标记—material symbol模具编号—mold number (no.)日期印—dating insert, date code循环印—cycling code公司标志—company logo技术要求Specification (SpecialRequirement)项目启动表Kick-off sheet项目名称—program name,project name产品名称—part name, productname, part description产品编号—part number (P/N)客户模号—customer mold no.项目启动日期—kick off date,start date项目完成日期—due date, leadtime内模件用钢—tool steel型腔数量—number of cavities数模文件编号—data file no.注塑材料—resin, plastic, rawmaterial收缩率—shrink, shrinkage, shrinkfactor注塑机吨位—molding machinesize, injection machine size成型周期—cycle time型腔光洁度—cavity polish型芯光洁度—core polish皮纹（晒纹）—texture, grain拔模斜度—draft angle, removaltaper注塑件颜色及光泽—moldedcolor & gloss模具加工地—manufacturingfacility热流道供应商—manifoldmanufacturer, manifold supplier浇口位置—gate location /position浇口类型—gate type产品标识—stamp information,part identification特殊要求—special instructions产品质量及外观要求Part Quality& Appearance尺寸及公差Dimension &Tolerance重要尺寸—critical dimension,important dim., key dim.理论尺寸—nominal dimension实际尺寸—actual dimension公差—tolerance公差带—tolerance range尺寸超差—dimension deviation接受（合格）—accept, OK拒绝（不合格）—reject, refuse,obsolete, NG让步接受—concession, specialadmit返工—re-work产品缺陷（较常见）Defects (normal)缩印—sink mark, shrinkage飞边—flash, burr段差—mismatch discrepancy银丝纹—snake marks, streak弯曲—warpage, distortion打不足（缺料）—short shot熔接线—weld line产品外观Part Appearance产品颜色—part color产品光泽—gloss皮纹粒度—grain常用词汇、词组及短语NormalWord, Short Sentence单边—per side双边—both sides加入，添加—add, incorporate去除，取消—remove, cancel满足…的要求，符合，与…要求一致—according to, conform to,satisfy, meet要求，需要—require, need,demand确认—be approved, agreed by …允许—permit, allow在…范围之内—within不可以，不允许，禁止—free from, prevent, avoid…，除非有另指—… unless otherwise specified…或少于—…or less自动化运作—automatic operation未注尺寸（详细形状）见三维造型Non dimensioned contour (detailed shape) see 3D model.分型线上的飞边（披缝）或段差应小于…Burrs and discrepancy on the P/L shall be … or less.标题栏Title Block产品名称—part name图纸编号+ 版本号（索引号）—drawing no. + level (index)一般公差[的标准] —general tolerance（三）如何阅读制模标准？How to read tooling standard?一．模具结构术语Mold Construction TerminologyA．模架Mold Base模架量化特征Measurement Feature①长X 宽X 高—Length X Width X Height②模具推高尺寸（模厚）—stack height of mould③模具重量—total weight of mould, mould thickness定模底板—front plate, top clamping plate, clamp plate, clamping plate定模板—cavity plate, fixed mould plate, A – plate动模板—core plate, moving mould plate, B – plate支撑板—support plate, backing plate模脚—support blocks, rails, risers, spacer block顶杆固定板—retaining plate, ejector retaining plate顶板—ejector plate动模底板—back plate导柱—guide pillar, leader pin,guide pin导套—guide bush, leader pinbush复位杆—return pin, push-backpin弹簧—spring撑头—support pillar推板导柱、导套—ejection guidepin / bush挡钉—stop pin, stop button站立脚—standing-off pillars标牌—plaque scutcheonB．成型零部件mouldingcomponents型芯—core型腔—cavity镶针—core pin镶块—insert, split滑块—slide, sliding split斜顶—lifter, angled-lift splitA 斜顶头—lifter headB 斜顶杆—lifter rod, lifter shaft成型顶杆—moulding face pin,form pinC．浇注系统Feed System1．塑料Moulding主流道—sprue分流道runner①主分流道—main runner②二级分流道—branch runner分流道断面形状cross-sectionalshape of runner①圆形—full round②半圆形—semicircular③梯形—trapezoidal浇口gate常用浇口形式normal gate type :①边缘浇口（J型浇口）—edgegate, J – gate②侧浇口—side gate③潜伏式浇口—sub-gate,cashew gate, subsurface gate,submarine gate④潜伏式二次浇口(隧道式浇口)—tunnel gate onto feeder post⑤点浇口—pin gate⑥直接浇口(主流道型浇口) —sprue gate, direct gate⑦护耳式浇口—tab gate模腔—impression冷料井—cold slug well热流道—hot runner2．模具零件mold components定位圈—locating ring, locationring, register ring浇口套—sprue bush挡圈—stop ring浇口镶块—gate insert热流道板—manifold热嘴—hot dropD．分型面及其锁紧、排气PartingSurface, inter-locking & venting分型线—parting line ( P/L )镶拼线—bodyline, joint line平/ 不平的分型面—flat / non –flat parting surface封胶面—shut off surfaces,seal-off surfaces擦位—shut off碰穿位—kiss-off管位—parting line lock分型面的释放(避空) —relief ofparting surface分型面的平衡—balancing ofparting surface锁紧角度—locking angle锁紧力—clamping force锁模板—safety strap精定位—Interlock, die lock困气—air trap排气槽—vent, vent slotE．滑块机构Slide驱动Actuation①斜导柱—angled pin, horn pin,cam pin②弹簧—spring③油缸—hydraulic cylinder制动Detention①滑块固定器—slide retainer②弹簧制动器—spring-loadeddetention (plunger)③挡钉、挡板—stop pin, stopplate, slide stop导轨—gib, guide strip锁紧块（楔紧块）—heel block, locking heel, wedge block, chase block耐磨片—wear plate, wear strip压板—retainer螺钉—screw定位销—dowelF．斜顶机构Lifter斜顶头—lifter head斜顶杆—lifter rod, lifter shaft开口销—split pin固定板（压板）—retainer plate 耐磨片—wear plate铜导套—bronze bushing衬套—spacer导轨—L – gib滑动块—slideG．顶出系统Ejection System基本词汇Basic Word顶出行程—ejection stroke模具开档—daylight粘模—stick产品脱模—part is push off from, clear part of mould, separation of part顶板机构Ejector plate assembly顶板（推板）—ejector plate顶板固定板—retaining plate推板导柱—ejector guide pin推板导套—ejector guide bush撑头—support pillar, pillar support复位机构Return System复位杆（回程杆）—return pin, push – back pin挡钉—stop pin, stop button压簧—compressed spring碟簧— a stack of “Belleville” washers早复位机构—early return system 强制复位机构—positive return system顶出方法Ejection Techniques顶杆顶出—pin ejection顶管顶出—sleeve ejection顶块顶出—bar ejection 扁顶顶出—blade ejection顶板顶出—stripper ejection油缸顶出—hydraulic ejection气顶—air ejection阀门顶出—valve ejection顶出组件Ejection Elements拉料杆—sprue puller, sucker pin顶杆—ejector pin阶梯式顶杆—stepped ejector pin顶管—ejection sleeve, sleeve扁顶—ejector blade, slabbed offejector pin顶块—stripper bar顶环—stripper ring推板—stripper plate加速顶—accelerated ejection顶出辅助机构Supplementaryoperating system弹簧柱塞器—spring –loadedplunger弹珠定位器—ball catch system插销式锁扣—Latch – lock尼龙拉杆装置—friction pullerdevice电器组件Electric Components压力传感器—pressure transducer限位开关—limit switchF．冷却系统Cooling System基本词汇Basic Word温差—temperature variation水孔（水道）—waterlines,water-ways, flow-way, channel水路—cooling circuit水路示意图—water schematic,schematic circuit冷却液—coolant, coolant fluid内连接—interconnect外连接—external connection出口、入口—outlet、inlet漏水—water leakage水路分布Circuits阶梯式水路—stepped system喷淋—baffled hole system斜孔式水路—angled hole system水路组件Components闷头（螺塞、止水栓）—（threadless）brass pressure plug :female plug & male隔水片—baffle密封圈—O – ring快插水路接头—quick disconnectfitting, quick connection adaptor弯头—elbow偶合器（连接器、接头）—adaptor(including a plug & a socket)橡皮管—rubber hose分水板—water manifoldG．螺纹、螺纹孔& 螺钉Thread,thread hole & screw螺纹—thread管螺纹—pipe thread螺纹孔—screw hole, tapped hole起吊孔—handling hole, jackscrew hole, eye bolt hole螺钉—screw内六角螺钉—socket headed capscrew （s.h.c.s.）沉头螺钉—flat headed cap screw（f.h.c.s）螺栓—bolt, eye bolt螺母—nut锁紧螺母—locknut螺纹标准Thread Standard①公制标准—Metric②英制标准—Imperial③英制管螺纹标准—BritishStandard Pipe thread （BSP）④美制管螺纹标准—NPT⑤美制粗螺纹标准—UnitedCoarse thread （UNC）⑥美制细螺纹标准—UnitedFine thread （UNF）H．润滑Lubrication润滑槽—grease groove加油管—grease line油杯—lubrication fitting测量仪器Measuring Instruments游标卡尺—vernier caliper千分尺—micrometer高度规—height gauge刻度规—dial gauge三坐标测量仪—CoordinateMeasure Machine（CMM）塞规—pin gauge圆角量规—radii gauge轮廓投影机—profile projectorJ．注塑机参数Injection Machine Parameter注塑机规格参数Injection Machine Specification①锁紧类型clamp typea．油缸—hydraulic b．肘杆式—toggle②垂直注塑机导柱间距—tie bar vertical clearance③水平注塑机导柱间距—tie bar horizontal clearance④台板尺寸—platen dim.⑤最小/ 最大模厚—mold height Min. / Max., Min. / Max. mold thickness⑥最小/ 最大注塑机开档—open daylight Min. / Max.⑦锁紧行程—clamp stroke⑧锁紧力—clamping force⑨顶出行程—ejector stroke⑩顶出力—ejector force试模工艺参数Moulding Process Parameter, machine setting①时间Timer（TM）, sec注塑（充填）时间—filling time, injection time冷却时间—cooling time补缩时间—packing time保压时间—holding time成型周期—cycle time②速率、速度Velocity, %、speed, in/sec注塑（充填）速度—injection speed保压速率—hold pressure velocity 螺杆转速—screw rotation speed ③压力Pressure（Prs.）, psi注塑压力—injection pressure保压压力—hold pressure回压（背压）—back pressure④温度Temperature（Temp.）, °F 注塑机喷嘴温度—nozzle temp. 料筒前段、中段、后段温度—barrel front、middle、rear temp.模温—mould temp.料温—purged resin melt temp.空射料温—air shot melt temp. 关于注塑成型对产品造成的各种缺陷及解决方法(一)熔接痕熔接痕是由于来自不同方向的熔融树脂前端部分被冷却、在结合处未能完全融合而产生的。
注塑模具相关专业英语
百度文库- 让每个人平等地提升自我注塑模具相关专业英语：注射机injection machine三板模：3-plate mold;二板模：2-plate mold;模脚：mold foot动模板movable plate定模板stationary plate水口板runner plate顶针板ejector retainer plate推板ejecting plate方铁space plate动模固定板bottom clamping plate 定模固定板up clamping plate导柱guide pillar导套guide bush回程杆ejector plate return pin回程杆硬块垃圾钉锁模块顶针ejector pin方顶ejector pad斜顶lifter滑块slide斜导柱angle pin垫片wear plate镶件insert动模core定模cavity强行复位机构斜锲wedge顶块ejector pad支撑柱support pillar定位销locating pin运水管water rub tube导滑套bush推管ejector sleeve限位块stop block限位钉stop screw定位圈locating ring浇口套sprue bush活动镶件movable insert排气槽vent斜顶lifter 拉料杆sprue puller分料道拉料杆runner puller圆锥头拉料杆sprue puller, conical headed 扣鸡（尼龙拉钩）nylon latch lock型芯core型腔cavity垫板backing plate浇口gate浇口套口径sprue diameter浇注系统feed system浇口大小gate size直接浇口direct gate环形浇口ring gate侧浇口edge gate盘型浇口disk gate潜伏浇口submarine gate扇形浇口fan gate大水口edge gate细水口pin- point gate转水口switching runner gate流道runner主流道sprue分流道runner梯形流道trapezoidal runner热嘴hot sprue热流道板hot manifold发热管cartridge heater探针thermocouples插头connector plug插座connector socket运水water line喉管tube喉塞lien plug塑胶管plastic tube快速接头jiffy quick connector socket收缩率shrinkage注射压力injection pressure成型压力molding pressure拉伸力drawing force锁模力clamping force开模力mold opening force 脱模力ejection force 抽芯力core-pulling force抽芯距core-pulling distance五金模具相关专业词汇：Progressive forming & punching Die（级进模和冲裁模）凸模垫板 Punch board凹模拼块 Combination die凸模固定板 Punch holder board压料板 Pressing board凹模垫板 Die board小压料板 Mini pressing board小固定板 Mini punch holder下模座 Down mould frame上模座 Up mould frame顶料销b lifter pin b锁模板 Clamping plate导正销a Pilot punches A导正销b Pilot punches b顶料销a lifter pin A侧挡板 Side baffle 抬料块 lifter block固定挡料块 Fixing baffle凸模 Punch导料孚料钉 Guide lifter sets斜契固定板 Cam slide holder斜契 Cam slide units活动呀板 Acting baffle导料孚料钉3 Guide lifter sets 3 导料机构 Guide lifter frameworker 压筋凸模 Pressing punch检测销安装板 Plotes for sensor翻空凸模 Rout up punch压筋凸模2 Pressing punch 2弯边凸模 Bend punch上模座Up mould framestripper guide bushingsstripper guide pins标题栏设计DESIGN制图DRAWING审核CHECK工艺PROCESS标准化STANDARDIZATION日期DATE标记MARK处数AMOUNT/PLACES(PLS)更改文件号CHANGED FILE NO./REVISED FILENO./REVISION签字SIGNA TURE数量QUANTITY重量WEIGHT比例SCALE共张TOTAL第张NO./ sheet x of y使用单位APPLICATION UNIT/UNIT使用设备APPLICATION EQUIPMENT/ EQUIPMENT 序号SERIAL NO.代号CODE名称NAME材料MATERIAL热处理HEAT TREATMENT备注NOTE1. IP095004修边压筋模上模板UPPER DIE SEAT凸模固定板PUNCH PLATE /PUNCH-RETAINER PLATE螺钉SCREW压形凹模COINING DIE卸料螺钉LIFT SCREW矩形弹簧RECTANGLE SPRING切口凸模SLOTTING PUNCH销PIN压料板BLANK HOLDER/Pressure plate上挡板UPPER BLACK-UP BLOCK /UPPER BAFFLE 小导柱SMALL GUIDE PIN/PILLAR小导套SMALL GUIDE BUSH冲孔凸模PIERCING PUNCH冲缺凸模SLITTING PUNCH下模固定板LOWER DIE HOLDER (PLATE)冲孔凹模镶件PIERCING DIE INSERT固定挡料销FIXED STOP PIN压筋凸模镶件EMBOSSING PUNCH INSERT压凸包镶件Doming insert压印凸模COINING PUNCH下模垫板LOWER DIE BOLSTER下挡板LOWER BACK-UP BLOCK Lower baffle限位键LIMITED KEY/LIMITED BLOCK下模组件LOWER DIE SUBASSEMBL Y压形凸模镶件COINING PUNCH INSERT/GROOVINGINSERT下模板LOWER DIE SEAT导向件GUIDE PART限位柱LIMITED POST储运垫块BUMPER BLOCK/ PAD BLOCK细铁链THIN IRON CHAIN吊柱DA VIT锁模板CLAMPING PLATE下垫架组件LOWER DIE BLOCK SUBASSEMBL Y/LOWER PAD BLOCK SUBASSEMBL Y工序图PROCESS PICTURE SHEET/PROCESSDRAWING成形凸模FORMING PUNCH成形凹模FORMING DIE挡块BACK-UP BLOCK/BAFFLE BLOCK卸料板Stripper PLATE弯边下模FLANGING DIE顶料板KNOCKOUT PLATE/LIFT PLATE凸模组件PUNCH SUBASSEMBL Y下模固定板LOWER DIE HOLDER下模座(下模板) LOWER DIE SEAT/ LOWER CLAMPING PLA TE 上限位柱UPPER LIMITED POST下限位柱LOWER LIMITED POST3、据付板翻边压级模无新词4．据付板拍平冲孔模未显示凸凹模PUNCH－DIE/PUNCH MATRIX定位钉LOCATING PIN退料板STRIPPER PLATE废料切刀SCRAP CUTTER废料箱SCRAP BOX胶条RUBBER STRIP靠板Backup plate定位块LOCATING BLOCK定位座LOCATING SEAT模柄DIE SHANK7.后盖板弯边模无新词活动定位ACTIVE LOCATOR/MOV ABLE LOCATION耐磨片WEAR RESISTANT PIECE送件装置FEED EQUIPMENT导向装置总成GUIDE QUIPMENT ASSEMBL Y氮气弹簧ACRIDINE SPRING气缸STEAM, CYLINDER9, 2P096439前板1修边冲模第二部分-改模后冲方孔凸模Rectangle piercing punch卸料销Stripper pin切角凸模Cutting punch刮料板组件Scrapper component运输装置组成Transfer equipment components挡料组件Stop component顶块Knockout block/LIFT BLOCK分流器Separator装置总成气缸固定板Cylinder holder滚轮座Roller seat连接板Connecting board日本小汽缸Japan small cylinder开槽沉头螺钉Grooved countersunk nut尼龙滚轮Nylon roller wheel深沟球轴承Deep slotted ball bearing紧固螺钉Fastening screw传送轮Delivery wheel小轴Small axis六角螺母HEXAGON NUT固定板Dead plate内六角平端紧定螺钉Flat end clamping hexagonal socket nut支撑小轴Small support spindle支撑板Support board刮料组件Scrapper components送料气缸Feed cylinder安装板Fixing plate浮料钉Floating pin顶块Knockout block后顶料装置Back knockout equipment/REAR LIFTEQUIPMENT前顶料装置Front knockout equipment/FRONT LIFTEQUIPMENT推料装置Knockout equipment/PUSH EQUIPMENT装配时冲方孔凸模（A）按长短两种间隔排列，如图示Rectangle punchs（A）arranged at intervals of long and short when assembled, shown as fig.压板PRESSURE PLA TE/Holder转板FLAP卡簧Spring washer/circlip拖板PLANKER长气缸LONG CYLINDER顶销EJECTOR PIN/Lift pin弹性挡料装置总成ELASTIC STOP ASSEMBLY带套卸料螺钉Eq-height sleeves bolt螺塞SCREW PLUG活动上模ACTIVE PUNCH SEAT/movable punch seat氮气缸GAS SPRING/ Nitrogen cylinder气缸支架CYLINDER BRACKET橡胶块RUBBER BLOCK上抽块下抽块活动挡料块ACTIVE STOP BLOCK/movable stop block镶件INSERT泰国滑块镶件SLIDE INSERT滑块SLIDE导向压板Guide holder斜楔WEDGE/cam driver斜楔固定板Wedge holder/ cam driver holder垫圈Cushion/Washer顶杆Ejector pin/kicker pin料套Lifter bushes托料组件Lifter component顶柱EJECTOR SHORE粗定位Rough location旧底图总号Former main drawing NO.底图总号Main drawing NO.描校描图Drawing借（通）用件登记Register general components其余Unless stated or specified/others废料箱Scrap box周边倒角Outside chamfer技术要求Notes外周边倒角Chamfer the adjacently outside未注圆角Unmarked round/unmarked corner锐角倒钝Blunt the sharp edgeA部详细Details of part A/detail A未注公差Unmarked tolerance退料钉Stripper pin日本标准号Japanese standard code/JIS code此图为参考日本标准件手册所绘制This drawing is designed consult the Japanesestandard component manual带*尺寸以冲孔凸模配做双面间隙: Dimensions with * machined according topiercing punch, two-sided clearance:改模用图Drawing of modified mould三角形镶件Triangle insert喷火处理Flaming treatment/spray quench treatment以相应凸模为基准Regard relevant punch as datum/ datum base onrelevant punch模具中心Mould center表面粗糙度Surface roughness局部视图Broken view淬火Quench沉孔Countersunk hole以此线为基准，此线上面部分上翘: Regard this line as datum, the part above thisline tilted up:单边缩小One-side shrink/offset inward工装等级Process assembly class安全等级Safe class导向件倒装Invert guide components所有挂槽深5 All trough hangs’ depth are 5拼块Mosaic block漏料箱仰视图Bottom view工件采用板料折弯，焊接成形,并配装把手The work piece adopts bending sheet metal,shaped by welding, assembled with handles拼合面Mosaic surfaceA部放大Detail A翻边孔Flanging hole底孔Bottom hole螺钉连接Screw joint滚轮座The seat of roller刮件装置装配关系，左右对称各一,尺寸参照图形The scrapper assembly relations: one each side symmetrically, the dimensions are referred tothe drawings组件The components尾部回火Tail tempering仅供参考For reference only漏料孔未注转角为R3 Unless stated or specified, the radius of scrapholes is 3mm.非工作边倒3X45ºChamfer 3X45ºexcept working edge.S50C按图示尺寸双面缩小~线割Wire-cut part S50C, offset ~ inward accordingto the indicated dimensions.两种不同规格的限位柱配合使用. The two different type of setting posts shouldbe matched to use.未注冲裁圆角为R3. The blanking corner is R3 unless stated orspecified.带**号尺寸按图示名义尺寸双面放大~. The dimensions with ** have been added~0.3mm on both sides according to thedimensions indicated.带**号尺寸所示位置为托料板所处位置,加工深度为A-A所示尺寸24. The location where dimensioned with ** is for lift plate, depth 24 as A-A view indicated.在上下模板中部右左两侧相对中心800加工安装锁模板的8-M16X30. Tap 8-M16X30 on both left and right sides of upper and lower die seats, symmetrized to their center line and offsetting 800mm.采用焊接结构,尖边倒钝Adapt the welded structure, blunt the sharpedges左侧板切角冲孔压筋模——技术要求——TECHNOLOGY REQUIREMENT热处理——HEAT TREATING锐角倒钝——Chamfer all the acute edge.所有凸模过孔与凸模配做，带*尺寸与凸模双面间隙-0.20mm，A B C D E F 部及中间大方孔应与相应凸模保证滑动配合。
注塑模具英语词汇
注塑模具英语词汇(总3页)--本页仅作为文档封面，使用时请直接删除即可----内页可以根据需求调整合适字体及大小--注塑模具英语词汇一、工程部 / Design department:1) Designer - 设计师。
2) Assembly drawing - 模具组装图。
3) Mold layout - 模具结构图。
4) 2D product drawing - 2D产品图。
5) 3D product data - 3D产品数据。
6) Part drawing - 散件图。
7) Insert molding - 镶件模。
8) 2 color mold / Double injection tool - 双色模。
9) Hydraulic system - 油/水压系统。
10) Parting line - 分模线。
11) Air venting - 排气槽。
12) Cooling system - 冷却系统。
13) Screw - 镙丝。
14) Hot runner system - 热流道。
15) Valve gate - 伐针入水口。
16) Fan gate - 扇型入水口。
17) Pin point gate - 针点进胶。
18) Moon gate / Banana gate - 香蕉，象牙入水口。
19) Submarine gate - 潜水口。
20) Injection machine tonnage - 注塑机吨数。
21) Number of cavity - 穴数。
22) Steel - 钢材。
23) Copper - 铜。
24) Tungsten copper - 钨铜。
25) Beryllium copper - 铍铜。
26) Hardening - 加硬/淬火。
27) Tempering - 回火。
28) Chroming - 电镀。
29) Painting - 喷漆。
30) Resin - 胶材。
模具标件专业英语词汇
模具标件专业英语词汇一、模具（Mold）相关基础词汇。
1. Mold [məʊld] - 名词，模具；也可作动词，塑造，浇铸。
- 例句：This is a new type of injection mold.（这是一种新型的注塑模具。
）2. Die [daɪ] - 名词，冲模，钢模（在冲压工艺中使用）- 例句：The die is used for stamping metal sheets.（这个冲模用于冲压金属薄板。
）3. Cavity ['kævəti] - 名词，型腔；洞，凹处。
- 发音：['kævəti]- 例句：The cavity of the mold should be polished carefully.（模具的型腔应该仔细抛光。
）4. Core [kɔː(r)] - 名词，型芯；核心。
- 例句：The core is an important part of the mold.（型芯是模具的一个重要部分。
）二、模具标件（Standard Mold Components）词汇。
1. Guide Pin ['ɡaɪ d pɪn] - 名词，导柱。
- 例句：The guide pin helps to align the two parts of the mold.（导柱有助于使模具的两个部分对齐。
）2. Guide Bushing ['ɡaɪ d 'bʊʃɪŋ] - 名词，导套。
- 例句：The guide bushing is used in combination with the guide pin.（导套与导柱配合使用。
）3. Ejector Pin [i'dʒektə pɪn] - 名词，顶针。
- 例句：The ejector pin is used to push the finished product out of the mold.（顶针用于将成品从模具中顶出。
塑胶模具行业专业术语
塑胶模具专业英语词汇1) Designer - 设计师。
2) Assembly drawing - 模具组装图。
3) Mold layout - 模具结构图。
4) 2D product drawing - 2D产品图。
5) 3D product data - 3D产品数据。
6) Part drawing - 散件图。
7) Insert molding - 镶件模。
8) 2 color mold / Double injection tool - 双色模。
9) Hydraulic system - 油/水压系统。
10) Parting line - 分模线。
11) Air venting - 排气槽。
12) Cooling system - 冷却系统。
13) Screw - 镙丝。
14) Hot runner system - 热流道。
15) Valve gate - 伐针入水口。
16) Fan gate - 扇型入水口。
17) Pin point gate - 针点进胶。
18) Moon gate -象牙入水口。
19) Submarine gate - 潜水口。
20) Injection machine tonnage - 注塑机吨数。
21) Number of cavity - 穴数。
22) Steel - 钢材。
23) Copper - 铜。
24) Tungsten copper - 钨铜。
25) Beryllium copper - 铍铜。
26) Hardening - 加硬/淬火。
27) Tempering - 回火。
28) Chroming - 电镀。
29) Painting - 喷漆。
30) Resin - 胶材。
31) Printing - 丝印。
32) Texturing - 嗮纹/咬花。
33) Socket screw - 带肩镙丝。
34) Inter lock / Straight lock - 模锁。
注塑模具专业词汇
模具专业英语词汇一、入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口： pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座： connector socket密封/封料： seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker 四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝： screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate模具述语一、入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口：pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter二、流道:runner热流道：hot runner,hot manifold热嘴冷流道:hot sprue/cold runner唧嘴直流:direct sprue gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针:thermocouples插头：connector plug插座：connector socket密封/封料：seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker 四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝：screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）：mold base上内模：cavity insert下内模：core insert行位（滑块）：slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头:support pillar唧嘴：sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞:pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith(core)side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.不准用镶件：Do not use(core/cavity)insert用铍铜做镶件：use beryllium copper insert初步（正式）模图设计：preliinary(final)mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper electrodeangle pin.finger cam (-:-)斜销angled-lift.splits (-:-)斜滑块backing plate.supprr plate (-:-)支承板baffle (-:-)隔板cartridge heater (-:-)管式加热器cavity(of a mould) (-:-)型腔cavity splits (-:-)凹模拼块cavity-retainer plate (-:-)凹模固定板chase.bolster.frame (-:-)模套clamping force.locking force (-:-)锁模力clog-leg cam (-:-)弯销cold-slug well (-:-)冷料穴compression mould (-:-)压缩模cooling channel.cooling line (-:-)冷却通道core splits (-:-)型芯拼块core splits (-:-)型芯core-pulling distance (-:-)抽芯距core-pulling force (-:-)油芯力core-retainer plate (-:-)型芯固定板dejection plate.ejector plate (-:-)推板direct gate spruce gate(-:-)直接浇口director guide fush.ejector bushing (-:-)推板导套disk gate (-:-)盘形浇口draft(-:-)脱模斜度edge gate (-:-)侧浇口ejection force (-:-)脱模力ejector guide pillar.ejector guide pin (-:-)推板导柱ejector housing.mould base leg(-:-)支架ejector pad(-:-)推块ejector pin (-:-)推出零件/推杆ejector pin with cylindrical head (-:-)圆柱头推杆ejector plate return pin.push-back pin (-:-)复位杆ejector retainer plate (-:-)推杆固定板ejector sleeve (-:-)推管ejector tie rod (-:-)连接推杆fan gate(-:-)扇形浇口feed system (-:-)浇注系统finger guide plate (-:-)斜槽导板fixed clamp plate,top clamping plate.top plate (-:-)定模座板fixed compression mould(-:-)固定式压缩模fixed transfer mould (-:-)固定式压注模flash groove,spew groove (-:-)排溢：溢料槽flash mould (-:-)溢式压缩模flat ejector pin (-:-)扁推杆force plunger,pot plunger (-:-)柱塞gate (-:-)浇口gating insert (-:-)浇口镶块guide bush.guide bushing (-:-)导套guide fush,hended.shonlder bushing (-:-)带头导套guide fush,straight.shraighr bushing (-:-)直导套guide pillar straight.straight leader pin (-:-)带头导柱guide pillar.guide pin.leader pin (-:-)导柱guide pillar.shouldered.shoulder leader pin (-:-)带肩导柱heat pipe(-:-)热管heating plate (-:-)加热板heel block,wedge block(-:-)楔紧块horingontal parting line (-:-)水平分型面(线)hot runner mould(-:-)热流道模impression cavity block.cavity plate (-:-)凹模injection mould (-:-)注射模injection mould for thermoplastics (-:-)热塑性塑料注射模injection mould for thermoses (-:-)热固性塑料注射模injection pressure (-:-)注射压力inserf(for moulding) (-:-)嵌件insulated runner mould (-:-)绝热流道模internal mould pressure.cavity pressure (-:-)模内压力internal mould pressure.cavity pressure (-:-)模内压力length bolt.puller bolt (-:-)定矩拉杆loading chamber (-:-)加料腔loading chamber (-:-)加料腔locating ring (-:-)定位圈/限位零件lower clamping plate(-:-)下模座板lower mould.lower half (-:-)下模manifold block hot-runner manifold (-:-)热流道板（柱）maximum daylight,open daylight(-:-)最大开距maximum daylight,open daylight(-:-)最大开距maximum daylight,open daylight(-:-)最大开距mould bases(of a injection mould) (-:-)模架(注射模)mould bases locating elements (-:-)锥形定位件mould for plastics (-:-)塑料成形模具mould for plastics (-:-)塑料成形模具mould for thermoplastics (-:-)热塑性塑料模mould for thermosets (-:-)热固性塑料模mould insert (-:-)镶件mould opening force (-:-)开模力mould plate (-:-)模板mould shut height(-:-)闭合高度moulding pressure (-:-)成形压力movable insert.loose detail (-:-)活动镶件movable insert.loose detail (-:-)活动镶件movable mould moving half (-:-)动模moving clamp plate.bottom clamping plate.bottom plate (-:-)动模座板parting line (-:-)分型：分型面pin-point gate (-:-)点浇口portable compression mould (-:-)移动式压缩模portable transfer mould (-:-)移动式压注模positive mould (-:-)不溢式压缩模projected area (-:-)投影面积projected area (-:-)投影面积puller plate.limit plate (-:-)定矩拉板punch force (-:-)凸模punch-retainer plate (-:-)凸模固定板ring gate (-:-)环形浇口runner (-:-)分流道runner plate (-:-)流道板runner puller.runner lock pin (-:-)分流道拉料杆runner stripper plate (-:-)推流道板runnerless mould (-:-)无浇道模secondary nozzle (-:-)二级喷嘴semi-positive mould (-:-)半溢式压缩模shot capacity (-:-)注射能力shot capacity (-:-)注射能力shouldered ejector pin (-:-)带肩推杆shrinkage (-:-)收缩率side core.slide core (-:-)侧型芯slide glide strip (-:-)滑块导板slide.cam slide (-:-)滑块slide.core-slide (-:-)侧型芯滑块spacer parallel (-:-)垫块splits(of a mould) (-:-)拼块spoke gate spider gate (-:-)轮辐浇口spreader (-:-)分流锥spruce(-:-)主流道sprue bush sprue busing (-:-)浇口套sprue puller (-:-)拉料杆sprue puller,ball headed (-:-)球头拉料杆sprue puller,z-shaper (-:-)钩形拉料杆sprue puller.conical headed (-:-)圆锥头拉料杆sprue puller.conical headed (-:-)圆锥头拉料杆standard mould bases (-:-)标准模架standard mould bases (-:-)标准模架standard mould bases (-:-)标准模架stationary mould fixed half (-:-)定模stop flock,stop pad (-:-)限位块stop pin.stop button (-:-)限位钉stripper distance (-:-)脱模距stripper distance (-:-)脱模距stripper plate (-:-)推件板stripper ring.strpper disk (-:-)推件环/盘submarine gate tunnel gate (-:-)潜伏浇口support pillar (-:-)支承柱ta be gate (-:-)护耳浇口thermal insulation board (-:-)隔热板thermal insulation board (-:-)隔热板thread plug,threaded core (-:-)螺纹型芯thread ring.threaded cavity (-:-)螺纹型环torpedo body assembly (-:-)鱼雷形组合体transfer mould (-:-)压注模、传递模upper clamping plate (-:-)上模座板upper mould,upper half (-:-)上模valve gate (-:-)阀式浇口venf(of a mould) (-:-)排气槽（孔）vertical parting line (-:-)垂直分型面(线) warm runner mould (-:-)温流道模warm runner plate (-:-)温流道板欢迎您的下载，资料仅供参考！致力为企业和个人提供合同协议，策划案计划书，学习资料等等打造全网一站式需求。
注塑模具英文
注塑模具英文模具英文专业术语压座/斜鸡: wedge一、入水: gate 耐磨板/油板: wedge wear pl ate进入位: gate l ocati on 压条: pl ate水口形式: gate type 撑头: support pi l l ar大水口: edge gate 唧嘴: sprue bushi ng细水口: pi n-poi nt gate 挡板: stop pl ate水口大小: gate si ze 定位圈: l ocati ng ri ng转水口: swi tchi ng runner/gate 锁扣: l atch唧嘴口径: sprue di ameter 扣鸡: parti ng l ock set二、流道: runner 推杆: push bar热流道: hot runner,hot mani fol d 栓打螺丝: S. H. S. B热嘴冷流道: hot sprue/col d runner 顶板: eracuretun唧嘴直流: di rect sprue gate 活动臂: l ever arm圆形流道: round(ful l /hal f runner 分流锥: spure sperader 流道电脑分析: mol d fl ow anal ysi s 水口司: bush流道平衡: runner bal ance 垃圾钉: stop pi n热嘴: hot sprue 隔片: buffl e热流道板: hot mani fol d 弹弓柱: spri ng rod发热管: cartri dge heater 弹弓: di e spri ng探针: thermocoupl es 中托司: ejector gui de bush插头: connector pl ug 中托边: ejector gui de pi n插座: connector socket 镶针: pi n密封/封料: seal 销子: dowel pi n三、运水: water l i ne 波子弹弓: bal l catch喉塞: l i ne l pug 喉塞: pi pe pl ug喉管: tube 锁模块: l ock pl ate塑胶管: pl asti c tube 斜顶: angl e from pi n快速接头: ji ffy qui ck connector pl ug/socker 斜顶杆: angl eejector rod四、模具零件: mol d components 尼龙拉勾: parti ng l ocks三板模: 3-pl ate mol d 活动臂: l ever arm二板模: 2-pl ate mol d 复位键、提前回杆: earl y return bar边钉/导边: l eader pi n/gui de pi n 气阀: val ves边司/导套: bushi ng/gui de bushi ng 斜导边: angl e pi n中托司: shoul der gui de bushi ng 术语: terms中托边L: gui de pi n 承压平面平衡: parti ng surface support bal ance 顶针板: ejector retai nner pl ate 模排气: parti ng l i ne venti ng 托板: support pl ate 回针碰料位: return pi n and cavi ty interference螺丝: screw 模总高超出啤机规格: mol d base shut hi ght管钉: dowel pi n 顶针碰运水: water l i ne i nterferes wi thejectorpi n开模槽: pl y bar scot 料位出上/下模: part from cavi th (core) si de 内模管位: core/cavi ty i nter-l ock 模胚原身出料位: cavi ty di rect cut on A-pl ate,core di rect cut on B-pl ate.顶针: ejector pi n 不准用镶件: Do not use (core/cavi ty) i nsert 司筒: ejector sl eeve 用铍铜做镶件: use beryl l i um copper i nsert 司筒针: ejector pi n 初步(正式) 模图设计: prel i i nary (fi nal ) mol d desi gn推板: stri pper pl ate 反呵: reverse core缩呵: movabl e core,return core core pul l er 弹弓压缩量: spri ng compressed l ength扣机(尼龙拉勾) : nyl on l atch l ock 稳定性好: good stabi l ity,stabl e斜顶: l i fter 强度不够: i nsuffi ci ent ri gi di ty模胚(架) : mol d base 均匀冷却: even cool i ng上内模: cavi ty i nsert 扣模: sti cki ng下内模: core i nsert 热膨胀: thero expansi on行位(滑块) : sl i de 公差: tol orance镶件: i nsert 铜公(电极) : copper el ectrode。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
NO. 英语 1 2 3 4 5 6 7 8 9 Injection Molding Machine Take-Out Robot Dryer Hopper Dryer Crushing Mill Gass Injection / AGI Machine Screw Screw Head 中国语 注塑机 机械手、产品取出机 干燥箱 料斗干燥器 粉碎机 吹气成形、气辅成形 机械、机器 螺杆、螺丝、螺旋 螺杆头 接头、接缝 注塑、注射 送料（加料）器 混炼料；化合物 混和、调合 混合器、搅拌器 混合、搅拌 冷却 冷却塔 冷水机、冷水装置 NO. 英语 365 Crystalline Polymer 366 Polymer 367 Injection Condition 368 Injection Molding Cycle 369 Precision Injection 370 Set the condition 371 Mold Set-Up 372 Mold Down 373 Pressure 374 Low Pressure 375 Low Pressure Clamping 376 Holding Time 377 Back Pressure 378 Clamping Force 379 Hold Clamping pressure 380 Clamping Stroke 381 Clamping Unit 382 Mold Opening 383 Mold Closing 384 Speed 385 Injection Speed 386 Injection Capacity 387 Charging 388 Charging Stroke 389 Rib 中国语 结晶性聚合物 聚合物 注塑条件 注塑周期 精密成形 设定注塑条件 上模、安装模具 落模、下模 压力 低压 低压锁模 保压时间 背压、返压 锁模力、合模力 锁模压力 合模行秳 锁模装置 开模 合模 速度 射出速度 注塑量 计量 计量行秳 骨位、筋位、加强筋
66 Try 67 Mold Release 68 Mold Release Agent 69 Rust Preventatives 70 Can’t Release 71 Shot 72 Gate 73 Center Gate 74 Sprue Runner 75 Clearance 76 Sprue 77 Runner 78 Air Vent 79 Breathing 80 Anneal 81 Mold 82 Machining Center 83 Universal Milling Machine 84 Lather 85 Surface Grinder 86 Grinding Drilling 87 Electric Discharge Machine 88 Wire EDM 89 Mitrided Steel 90 Mitrogen 91 Nitrize 92 Titanium 93 Heat Treatment 94 Hardening 95 Temper 96 Annealing 97 Prehaden 98 Hardness 99 Soft 100 Electrodes 101 Insert 102 Slide 103 Taper 104 Taper 105 Draft
10 Jointo 11 Injection 12 Feeder 13 Compound 14 Blend 15 Mixer 16 Mixing 17 Cooling 18 Cooling Tower 19 Chiller
20 Temperature Controller 温调机 21 Cylinder 22 Heater 23 Band Heater 24 Themocouple 25 Nozzle 料筒（注塑机） 加热器、发热器 加热圈、热器带 热电偶 射嘴、喷嘴
106 Guide Pin 107 Sleeve Pin 108 Squrae Pin 109 Angular Ejector 110 Cavity 111 Core 112 Mumber of Cavities 113 Rocket Ring 114 O Ring 115 Wall Tickness 116 Add Material 117 Building 118 Cut Material 119 Modity the tooling 120 Repairing the tooling 121 Design 122 Design Drawing 123 Design Change 124 Designer 125 Designer 126 Mold Design 127 Mold Specification 128 Specification 129 Mold Construction 130 Input 131 Programming 132 3D Drawing 133 2D Drawing 134 Front Elevation 135 Plan
导向柱 司筒针 扁顶针 斜顶针 模腔、刾模、母模 模心、后模、公模 取数、模腔数 定位环（圈）
470 Engrave 471 Texture 472 EDM Texture 473 Rough 474 Trifling 475 Diamond Cut 476 Roulette 477 Blast
刻印 蚀纹 火花纹 粗癿 细癿、幼癿 钻石纹 滚花刀、刻痕 喷沙 热流道 修理 溶接、烧焊 焊机、电焊机 焊条、电焊条 氩弧焊 喷燃烧器、火焰燃烧器 顶出 顶针 水口方式 遂道式浇口、潜水口 针孔形浇口、细水口 侧水口、大水口 直接浇口 复式浇口 扇形浇口 扇形浇口 搭接浇口 浇口平衡 凹槽、倒扣 水管、运水 散水 冷却回路、运水 模型制造 模型、原尺寸模型 手板、手工样品 模数、模量；模件 齿轮；传动装置 螺旋齿轮 整体癿；固体 变换、转换 磁盘、软盘
壁厚丌均匀 气泡、空洞、空隙 条纹 污垢、污点、渗溢 脱落、剥落 翻卷 浮起 螺丝滑牙 员数丌足、欠品 跳动度、偏心 收缩 嵌合丌良、装配丌良 应力 内应力 安排、准备 挡块 推板、脱模板 垫板 模胚 托板 撑头 拉塞 拉杆 工字板、水口板 底板 回针 导柱 导套 模具、动模、秱动模板 模板、载模板 模块、模件、模数 钢丝、钢丝绳 锉刀 油石 砂纸 节号、目
嵌件、嵌入 胶厚、壁厚 塑化 热分解 收缩 树脂 原料、材料 塑料、塑胶制品 橡胶 色母 色粉、粉、粉末 色粉、干色料 粒、塑胶粒 玻璃纤维 软管、管 过充填 模伤、模痕 冲击、打击 损坏、损伤 缩水、收缩 充填丌足、欠料 毛刺、抦峰 胶丝 白化、顶白 银白、银痕 流纹 烧黑、烧焦 异物、黑点 粘模 溶接线、结合线 料花 油污、油渍 打痕、击伤 裂、开裂 气纹 变形 弯曲、翘曲、外倾 弯曲 扭曲 颜色丌均匀
射嘴头、喷嘴头 拉杆、拉杠 拉杆间隔 限位（限制）开关 操作开关 操作指南 控制器、控制盘 全自动 半自动 手动 手柄、把手、操纵 押出机、挤塑机 挤塑 吹塑机 吹塑 秳序控制 工艺、工序、过秳 注塑工艺秳序控制装置 注塑秳序控制装置 冷料、早凝料 冷料井 冷凝 液压、油压 液压顶出、液压脱模 液压泵 液压马达 空器压缩机、空压机 漏油 油箱、油槽 活塞 气缸 报警 安全门 紧急停止 换色 清机塑料；过料 胶料温度 模温 升温、升热 空射胶、空打
试模 脱模 脱模刼 防锈刼 （产品）无法脱模；粘模 注、射、啤 进点，浇口 中心浇口 水口，注口、流道料 间隔、余隔 主流道、注（塑）口 流道、流道料 散气孔、通风口 排气、散气 热处理、退火 模具 加工中心 铣床、锣床 车床 平面磨床 钻床 火花机加工 线切割 氮化钢 氮气 氮化处理 钛 热处理 淬火 回火 退火 预加硬钢 硬度 软、软癿 铜公 镶件 行位、滑块 斜度 斜度、锥度、锥形癿 脱模斜度
430 Eccentric Wall Theckness 431 Boid、Cell 432 Stripes 433 Dirty 434 Flaking 435 Tear Off 436 Float 437 Screw Damage 438 Shortage 439 Runout 440 Contraction 441 Assembly NG 442 Stress 443 Intermal Stress 444 Preparation 445 Stopper 446 Stripper 447 Spacer Plate 448 Mould Base 449 Support Plate 450 Support Pillar 451 Puller Lock 452 Puller Bolt 453 Top Plate 454 Bottom Plate 455 Retum 456 Guider Pin 457 Guider Bush 458 Die 459 Die Plate 460 Module 461 Parts 462 Eye Bolt 463 Crane 464 Hook 465 Wire 466 File 467 Oil Stone 468 Sand Paper 469 Mesh
390 Insert 391 Wall Thickness 392 Plasticizing 393 Thermal Decomposition 394 Shrinkage 395 Resin 396 Material 397 Plastics 398 Rubber 399 Master Batch 400 Powder 401 Dry Color 402 Pellte 403 Glass Fiber Fibrous Glass 404 Hose 405 Over Packing 406 Mold Mark 407 Shock 408 Damage 409 Sink Mark 410 Short Shot 411 Flash 412 Steing Flash 413 White Mark 414 Silver 415 Flow mark 416 Burm Mark 417 Black Spot 418 Sticking 419 Weld 420 Flash 421 Oil Mark 422 Damage 423 Craking 424 Jetting 425 Deform 426 Warping 427 Bend 428 Torsion 429 Unever Color