克莱斯勒标准 MS-6179_S_ 公制系列钢制螺母(中英文)
螺丝名称的中英文对照表
螺丝名称的中英文对照表常用英文单词及简写形式No. 单词简写中文1 screw scr 螺丝2 nut nut 螺母3 washer wash 垫圈4 head hd 头5 thread thre 螺纹6 coating coat 镀层7 rivet riv 铆钉8 standoff stdoff 内外六角钉9 driver driv 穴10 hexagon hexa 六角11 tooth tooth 齿12 lock lck 锁13 spring spr 弹簧14 wave wave 波浪型15 pitch pitch 牙距16 partial thread P T 半螺纹17 PT PT 一种螺纹形式18 Full Thread FT 全螺纹19 silver silv 银20 cone cone 锥形21 Eco-syn Eco 30度牙的一种螺纹22 Thread Forming TF 自攻螺纹23 Self Tapping self tapp 自切屑螺纹24 pin pin 销25 shaft Shaf 轴26 steel St 铁27 stainless steel SS 不锈钢28 Brass(Cu) Bras(Cu) 铜29 Aluminum AL 铝30 Rubber Rub 橡胶31 machine screw mech scr 机制螺丝32 SEM screw SEM Scr 组合螺丝33 Material material 材料34 Grade GD 等级35 Finish Finish 表面处理36 Point Point 点37 Clamp Clam 夹子38 internal Int 内39 external ext 外40 thickness / 厚度41 length / 长度42 hole / 孔43 Metric Metcric 公制44 DIN / 德标45 ANSI / 美标46 JIS / 日标47 ISO / 国际标准48 NFE / 法标49 GB / 国家标准50 Quality / 质量51 surface hardness 表面硬度52 product treatment 表面处理53 plating 电镀54 heat 热55 Screws And Shafts For Motorcycle Or Bicycle 机(踏)车用螺丝、轴心56 Screws And Shafts For Sewing Maching 针车用螺丝、轴心57 Socket Set Screws 止付螺丝58 Stainless Steel Coarse Thread Screws 不锈钢宽牙螺丝59 Stainless Steel High-Low Thread Screws 不锈钢高低牙螺丝60 Stainless Steel Machine Screws 不锈钢机械螺丝61 Stainless Steel Self Drilling Screws 不锈钢钻尾螺丝62 Stainless Steel Self Tapping Screws 不锈钢螺丝class=a1>自攻螺丝63 Stainless Steel Thread Cutting Screws 不锈钢自削螺丝64 Stainless Steel Tri-Lobular Thread Screws 不锈钢三角牙螺丝65 Steel Ceiling Anchors 插片壁虎66 Drop in Anchors 内迫壁虎67 Steel Hit Anchors 碳钢锤钉壁虎68 Steel Hex Coupling Nuts 碳钢六角螺帽69 Wedge Anchors 强力车修壁虎70 Cut Anchors 外迫壁虎71 Chemical Anchors 化学壁虎72 Heavy Duty Expansion Anchors 不锈钢重载胀栓73 Tie Wire Anchors 鱼眼壁虎企眼长螺帽74 Hammer Drive Anchors 锌合金打入式壁虎75 Strut Nuts 弹簧螺帽76 Toggle Bolts (Spring Toggle & Gravity Toggle) 兰花夹系列77 Nylon Frame Anchors or Metalframe Anchors 门窗、地板专用壁虎78 Hollow Wall Anchors 石膏板中空壁虎79 Sleeve Anchors 套管式壁虎80 Nylon Frame Harmmer Fixing (Nylon Hammer Drive Anchors) 打入式壁虎鱼形尼龙壁虎81 Hit Anchors 强力式锤钉壁虎82 Bolt Anchors 电梯壁虎83 Heavy duty anchors 重载壁虎84 Loxin Masonry Anchors 两片夹85 Set Bolts 定位螺栓86 Short Strap Anchors 长型兰花夹87 Drop in Setting Tools 工具棒88 Elephant foot anchors 象脚壁虎89 Concrete Insert 水泥预埋件90 Drop in Anchor with Lip 翻边胀轴91 Legs Drywall Anchors 冲件92 Hex Cap Nuts 六角盖头螺帽93 Hex Serrated Nuts 六角锯齿螺帽94 Hex Flange Nuts 六角轮缘螺帽95 Hex Coupling Nuts(High Nuts) 高脚螺帽96 Round Nuts 圆螺帽97 Square Nuts 四角螺帽98 Pipe Nuts 管用螺帽99 Wheel Nuts 轮壳螺帽100 Wing Nuts 蝶型螺帽101 U Nuts U形螺帽102 T Nuts T形螺帽103 Eye Nuts 环首螺帽104 Kep Nuts 齿形螺帽105 Clinch Nuts 齿花螺帽106 Corten Steel Heavy Hex Nuts 耐候钢六角重型螺帽107 Weld Nuts 焊接螺帽108 Heigh Strength Nuts 高张力螺帽109 Structural Nuts 建业用螺帽110 Stainless Steel Nuts 不锈钢螺帽111 Brass Nuts 铜螺帽112 Aluminum Nuts 铝螺帽113 Alloy Steel Nuts 合金钢螺帽114 Heavy Duty Wheel Hub Nuts 重型车螺帽115 Acorn Cap Nuts 铁器焊接袋帽116 All-Metal Prevailing Torque Type Nuts 金属预置扭矩式螺帽117 Anchor Nuts 壁虎螺帽118 Big Size Nuts 大尺寸螺帽119 Closed End Acorn Nuts 铁盖袋帽120 Conical Washer Nuts 盘形华司螺帽121 Din 986 Domed Cap Nuts 铁盖+尼龙圈组合盖帽122 Flange Nylon Insert Lock Nuts 突缘尼龙盖帽123 Flat Waser Nuts 平面华司螺帽124 Hex Slotted Nut 六角割沟螺帽125 Self-Locking Nuts 自锁螺帽126 Sliding Nuts 制止螺帽127 Sln Self-Locking Nuts Sln-自动防松螺帽128 Special Nuts 其它特殊螺帽129 Spring Nuts 弹簧螺帽130 Stainless Steel Flange Nuts 不锈钢突缘螺帽131 Stainless Steel Flange Nylon Insert Lock Nuts 不锈钢六角轮缘尼龙螺帽132 Stainless Steel Heavy Hex Nuts 不锈钢六角重型螺帽133 Stainless Steel Hex Nuts 不锈钢六角螺帽134 Stainless Steel Nylon Insert Lock Nuts 不锈钢尼龙嵌入螺帽135 Hex Nuts 普通六角螺帽136 Heavy Hex Nuts 六角重型螺帽137 Hex Jam Nuts 薄型螺帽138 Nylon Insert Lock Nuts 尼龙嵌入防松螺帽139 Hex Machine Screw Nut 机械螺丝用六角螺帽140 Hex Head Cap Screws(Hex Bolts) 六角螺丝(栓)141 Hex Head Machine Bolts 六角机械螺丝142 Hex Lag Bolts 六角木牙螺丝143 Square Head Bolts 四角螺丝144 Carriage Bolts 马车。
DIN标紧固件地中文对照
DIN标紧固件的中文对照序号德国标准中文译文4 DIN 1 圆锥销5 DIN 7 圆柱销6 DIN 84 开槽圆柱头螺钉7 DIN 85 开槽盘头螺钉8 DIN 93 单耳止动垫圈9 DIN 94 开口销10 DIN 95 开槽半沉头木螺钉11 DIN 96 开槽半圆头木螺钉12 DIN 97 开槽沉头木螺钉13 DIN 125-1 平垫14 DIN 125-2 平垫(带倒角)15 DIN 126 平垫16 DIN 127-1 重型弹垫17 DIN 127 标准弹垫18 DIN 128-1 波形弹垫19 DIN 137-1 弹簧止动垫圈20 DIN 137-2 鞍形弹垫21 DIN 186 T型方颈螺栓22 DIN 188 T型双接头螺栓23 DIN 258 螺纹圆锥销24 DIN 261 T型头螺栓25 DIN 315AF 蝶型螺母(美制)26 DIN 315DF 蝶型螺母(德制)27 DIN 316AF 蝶型螺钉(美制)28 DIN 317DF 蝶型螺钉(德制)29 DIN 319 圆球型盖型螺母30 DIN 404 开槽带孔球面圆柱头螺钉DIN40531 DIN 417 开槽长圆柱端紧定螺钉32 DIN 427 开槽平端紧定螺钉(半牙)33 DIN 431 小六角特薄细牙螺母34 DIN 432 外舌止动垫圈35 DIN 433 小垫圈(用于圆柱头螺钉)36 DIN 434 方斜垫圈(U型)37 DIN 435 方斜垫圈(I型)38 DIN 436 方垫圈39 DIN 438 开槽凹端紧定螺钉40 DIN 439 六角薄螺母41 DIN 439 六角薄螺母B级无倒角42 DIN 439 细牙六角薄螺母43 DIN 440 木螺钉专用垫圈44 DIN 443 密封帽45 DIN 444 活节螺栓B 型46 DIN 462 内舌止动垫圈47 DIN 463 双耳止动垫圈48 DIN 464 滚花高头螺钉49 DIN 465 开槽滚花高头螺钉50 DIN 466 滚花高螺母51 DIN 467 滚花薄螺母52 DIN 470 锁紧垫圈53 DIN 471 轴用弹性挡圈54 DIN 472 孔用弹性挡圈55 DIN 478 方头带垫螺栓56 DIN 479 方头圆柱底端螺栓57 DIN 480 方头带垫半圆底端螺栓58 DIN 481 弹性圆柱销59 DIN 508 T型槽螺母60 DIN 525 单头螺柱61 DIN 529 地脚螺栓62 DIN 546 带槽圆螺母63 DIN 547 端面带孔圆螺母64 DIN 551 开槽平端紧定螺钉65 DIN 553 开槽锥端紧定螺钉66 DIN 555 六角螺母67 DIN 557 方螺母-C68 DIN 558 六角头螺钉69 DIN 561 六角头圆柱端紧定螺钉70 DIN 562 薄型方螺母-B71 DIN 571 六角头木螺钉72 DIN 580 吊环螺钉73 DIN 582 吊环螺母74 DIN 601 六角头螺栓75 DIN 603 大半圆头方颈螺栓(马车螺栓) C级76 DIN 604 沉头带插销马车螺栓77 DIN 605 沉头长方颈马车螺栓78 DIN 607 半圆头带插销马车螺栓79 DIN 608 沉头短方颈马车螺栓80 DIN 609 六角头精配螺栓（长螺纹）81 DIN 610 六角头精配螺栓（短螺纹）82 DIN 653 滚花平头螺钉83 DIN 660 半圆头铆钉84 DIN 661 沉头铆钉85 DIN 662 半沉头铆钉86 DIN 674 大扁头铆钉87 DIN 703 重型侧面带孔圆螺母88 DIN 705 侧面带孔圆螺母89 DIN 741 卡头90 DIN 787 T型槽螺钉91 DIN 835 双头螺柱（牙长=2D）92 DIN 906 内六角锥型闭锁螺钉93 DIN 908 内六角直型闭锁螺钉94 DIN 909 外六角锥型闭锁螺钉95 DIN 910 外六角直型闭锁螺钉96 DIN 911 内六角扳手97 DIN 912内六角圆柱头螺钉98 DIN 913 内六角平端紧定螺钉99 DIN 914 内六角尖端紧定螺钉100 DIN 915 内六角圆柱端紧定螺钉101 DIN 916 内六角凹端紧定螺钉102 DIN 917 薄型盲螺母103 DIN 920 开槽小圆柱头螺钉104 DIN 921 开槽大圆柱头螺钉105 DIN 923 开槽圆柱头轴肩螺钉106 DIN 927 开槽无头轴肩螺钉107 DIN 928 焊接方螺母108 DIN 929 焊接六角螺母109 DIN 931 六角头螺栓（半牙）110 DIN 933 六角头螺栓（全牙）111 DIN 934 六角头螺母(1型)112 DIN 934-2 细牙六角头螺母(1型) 113 DIN 935 开槽六角螺母114 DIN 936 六角头薄螺母115 DIN 937 六角头开槽薄螺母116 DIN 938 双头螺距（牙长=1D）117 DIN 939 双头螺距（牙长=1.25D）118 DIN 939 双头螺距（牙长=1.5D）119 DIN 940 双头螺距（牙长=1.5D）120 DIN 960 六角头细牙螺栓（半牙）121 DIN 961 六角头细牙螺栓（全牙）122 DIN 962 头部穿孔六角头螺栓123 DIN 963 开槽沉头螺钉124 DIN 964 开槽半沉头螺钉125 DIN 965 十字槽沉头螺钉126 DIN 966 十字槽半沉头螺钉127 DIN 970 六角头螺母128 DIN 971 六角头螺母129 DIN 972 细牙六角头螺母(2型)130 DIN 975 牙条(全螺纹)131 DIN 976 螺纹销132 DIN 979 六角头开槽薄螺母（2型）133 DIN 980 全金属六角锁紧螺母（1型）134 DIN 981 圆螺母135 DIN 982 六角头尼龙锁紧螺母136 DIN 985 六角头薄型尼龙锁紧螺母137 DIN 986 六角盖型尼龙锁紧螺母138 DIN 988 配合垫片139 DIN 1052 木材连接用垫片140 DIN 1151 沉头钢钉141 DIN 1440 销钉专用垫片A型142 DIN 1441 销钉专用垫片143 DIN 1444 带头销钉144 DIN 1471 圆锥型槽销145 DIN 1472 圆锥型槽销(半槽)146 DIN 1473 平行槽销(带倒角)147 DIN 1474 前端凹槽槽销148 DIN 1475 中部凹槽槽销149 DIN 1476 圆头槽销150 DIN 1477 沉头槽销151 DIN 1479 六角螺母棒152 DIN 1480 花篮螺栓153 DIN 1481 弹性圆柱销开槽重型154 DIN 1587 组合式盖型螺母155 DIN 1804 开槽圆螺母（配合沟头扳手）156 DIN 1816 圆螺母（带插销孔）157 DIN 2093 盘型弹簧垫圈158 DIN 3017 喉箍159 DIN 3404 润滑油嘴（旋扭头）160 DIN 3567 管夹161 DIN 3570 U型螺栓162 DIN 5587 2型六角螺母A和B级163 DIN 6319 球面垫圈164 DIN 6325 圆柱销165 DIN 6330 厚六角螺母166 DIN 6331 厚六角法兰面螺母167 DIN 6334 长六角螺母168 DIN 6797-A 外齿锁紧垫圈169 DIN 6797-I 内齿锁紧垫圈170 DIN 6798-A 外锯齿锁紧垫圈171 DIN 6798-I 内锯齿锁紧垫圈172 DIN 6799 开口挡圈173 DIN 6823 六角法兰面螺母174 DIN 6885 平键（A型）175 DIN 6888 半圆键176 DIN 6899 嵌环（支撑环）177 DIN 6900 机器螺钉和垫圈组合件178 DIN 6901 自攻螺钉和垫圈组合件179 DIN 6912 薄型带孔内六角圆柱头螺钉180 DIN 6914 大六角头螺栓181 DIN 6915 大六角螺母182 DIN 6916 大垫圈183 DIN 6917 楔型方垫圈184 DIN 6921 六角法兰面螺栓加大系列B级185 DIN 6923 六角法兰面螺母186 DIN 6925 全金属六角锁紧螺母(2型）187 DIN 7337 开口型抽芯铆钉（沉头、扁圆头）188 DIN 7338 扁平头半空心/全空心铆钉189 DIN 7343 螺旋夹紧销190 DIN 7346 轻型弹性圆柱销191 DIN 7349 重型弹性圆柱销用垫圈192 DIN 7500 ISO公制螺纹螺钉(多种头型)193 DIN 7504 自攻自钻螺钉(多种头型)194 DIN 7513 开槽切削螺纹螺钉(多种头型) 195 DIN 7516 十字槽切削螺纹螺钉(多种头型) 196 DIN 7965 T型四爪螺母197 DIN 7968 钢结构用六角头螺栓连接副198 DIN 7971 开槽盘头自攻螺钉199 DIN 7972 开槽沉头自攻螺钉200 DIN 7973 开槽半沉头自攻螺钉201 DIN 7976 六角头自攻螺钉202 DIN 7978 圆锥销203 DIN 7980 圆柱头螺钉用弹簧垫圈204 DIN 7981 十字槽盘头自攻螺钉205 DIN 7982 十字槽沉头自攻螺钉206 DIN 7983 十字槽半沉头自攻螺钉207 DIN 7984 薄型内六角圆柱头螺钉208 DIN 7985 十字槽盘头螺钉209 DIN 7989 钢结构用垫圈210 DIN 7990 钢结构用六角头螺栓211 DIN 7991 内六角沉头螺钉212 DIN 7993 轴用钢丝挡圈213 DIN 7995 十字槽半沉头木螺钉214 DIN 7996 十字槽圆头木螺钉215 DIN 7997 十字槽沉头木螺钉216 DIN 8140 螺纹护套（普通\自锁等）217 DIN 9021 大外径垫圈218 DIN 11024 弹簧卡子219 DIN 13257 平板螺栓220 DIN 18182 干壁钉（墙板钉）221 DIN 28129 环型螺母222 DIN 70952 圆螺母用止退垫圈螺丝，紧固件，标准件词汇的中英文对照机(踏)车用螺丝、轴心Screws And Shafts For Motorcycle Or Bicycle针车用螺丝、轴心Screws And Shafts For Sewing Maching止付螺丝Socket Set Screws不锈钢宽牙螺丝Stainless Steel Coarse Thread Screws不锈钢高低牙螺丝Stainless Steel High-Low Thread Screws不锈钢机械螺丝Stainless Steel Machine Screws不锈钢钻尾螺丝Stainless Steel Self Drilling Screws不锈钢自攻螺丝Stainless Steel Self Tapping Screws不锈钢自削螺丝Stainless Steel Thread Cutting Screws不锈钢三角牙螺丝Stainless Steel Tri-Lobular Thread Screws插片壁虎Steel Ceiling Anchors内迫壁虎Drop in Anchors碳钢锤钉壁虎Steel Hit Anchors碳钢六角螺帽Steel Hex Coupling Nuts强力车修壁虎Wedge Anchors外迫壁虎Cut Anchors化学壁虎Chemical Anchors不锈钢重载胀栓Heavy Duty Expansion Anchors鱼眼壁虎企眼长螺帽Tie Wire Anchors锌合金打入式壁虎Hammer Drive Anchors弹簧螺帽Strut Nuts兰花夹系列Toggle Bolts (Spring Toggle & Gravity Toggle)门窗、地板专用壁虎Nylon Frame Anchors or Metalframe Anchors石膏板中空壁虎Hollow Wall Anchors套管式壁虎Sleeve Anchors打入式壁虎鱼形尼龙壁虎Nylon Frame Harmmer Fixing (Nylon Hammer Drive Anchors)强力式锤钉壁虎Hit Anchors电梯壁虎Bolt Anchors重载壁虎Heavy duty anchors两片夹Loxin Masonry Anchors定位螺栓Set Bolts长型兰花夹Short Strap Anchors工具棒Drop in Setting Tools象脚壁虎Elephant foot anchors水泥预埋件Concrete Insert翻边胀轴Drop in Anchor with Lip冲件Legs Drywall Anchors六角盖头螺帽Hex Cap Nuts六角锯齿螺帽Hex Serrated Nuts六角轮缘螺帽Hex Flange Nuts高脚螺帽Hex Coupling Nuts(High Nuts)圆螺帽Round Nuts四角螺帽Square Nuts管用螺帽Pipe Nuts轮壳螺帽Wheel Nuts蝶型螺帽Wing NutsU形螺帽U NutsT形螺帽T Nuts环首螺帽Eye Nuts齿形螺帽Kep Nuts齿花螺帽Clinch Nuts耐候钢六角重型螺帽Corten Steel Heavy Hex Nuts 焊接螺帽Weld Nuts高张力螺帽Heigh Strength Nuts建业用螺帽Structural Nuts不锈钢螺帽Stainless Steel Nuts铜螺帽Brass Nuts铝螺帽Aluminum Nuts合金钢螺帽Alloy Steel Nuts重型车螺帽Heavy Duty Wheel Hub Nuts铁器焊接袋帽Acorn Cap Nuts金属预置扭矩式螺帽All-Metal Prevailing Torque Type Nuts壁虎螺帽Anchor Nuts大尺寸螺帽Big Size Nuts铁盖袋帽Closed End Acorn Nuts盘形华司螺帽Conical Washer Nuts铁盖+尼龙圈组合盖帽Din 986 Domed Cap Nuts突缘尼龙盖帽Flange Nylon Insert Lock Nuts平面华司螺帽Flat Waser Nuts六角割沟螺帽Hex Slotted Nut自锁螺帽Self-Locking Nuts制止螺帽Sliding NutsSln-自动防松螺帽Sln Self-Locking Nuts其它特殊螺帽Special Nuts弹簧螺帽Spring Nuts不锈钢突缘螺帽Stainless Steel Flange Nuts不锈钢六角轮缘尼龙螺帽Stainless Steel Flange Nylon Insert Lock Nuts 不锈钢六角重型螺帽Stainless Steel Heavy Hex Nuts不锈钢六角螺帽Stainless Steel Hex Nuts不锈钢尼龙嵌入螺帽Stainless Steel Nylon Insert Lock Nuts普通六角螺帽Hex Nuts六角重型螺帽Heavy Hex Nuts薄型螺帽Hex Jam Nuts尼龙嵌入防松螺帽Nylon Insert Lock Nuts机械螺丝用六角螺帽Hex Machine Screw Nut六角螺丝(栓) Hex Head Cap Screws(Hex Bolts)六角机械螺丝Hex Head Machine Bolts六角木牙螺丝Hex Lag Bolts四角螺丝Square Head BoltsT头螺丝T Head Bolts马车螺丝Carriage Bolts环首螺丝Eye Bolts内六角孔螺丝Hex Socket Cap Screws固定螺丝Set Screws螺椿栓Stud Bolts螺旋椿Screw Studs轮壳螺栓Wheel Bolts翼形螺丝Wing Screws自攻螺丝Self Tapping Screws自削螺丝Thread Cutting Screws钻尾螺丝Self Drilling Screws旋入螺丝Drive Screws机械螺丝Machine Screws木螺丝Wood Screws家具螺丝Furniture Screws塑板螺丝Chipboard Screws墙用螺丝Drywall Screws基础螺栓Foundation BoltsU型螺栓U Bolts勾头螺栓Hook Bolts套挂螺丝Toggle Bolts突缘螺丝Flange Bolts轨道螺栓(鱼尾螺丝) Track Bolts耐候钢螺丝Corten Steel Heavy Hex Bolts扭矩控制螺栓T.C.Bolts高张力螺栓High Strength Bolts剪力钉(焊接螺丝) Welding Studs螺丝附华司组合Screws And Washers Assembled(Sems) 大尺寸螺栓Big Size Bolts不锈钢小螺丝Stainless Steel Sheet Metal Screws不锈钢大螺丝Stainless Steel Bolts铜螺丝Brass Screws铝螺丝Aluminum Screws合金钢螺丝Alloy Steel Screws电子螺丝Electronic Screws微小精密螺丝Micro Screws塑料螺丝Plastic Screws复合材料用螺丝Particle Board Screws钛合金螺丝Titanium Alloy Bolts钛、锆、钼、铌等螺丝、零件、材料Ti,Zr,Mo,Nb Pare Metal Bolts Parts 拇指螺丝Thumb Screws双头牙螺丝Double End Screws Hanger Bolt车辆(汽车)螺丝、螺帽Automotive Fasteners航天用螺丝Aerospace Fasteners飞机特殊扣件Source Control Bolts拉栓Blind Bolts面板螺丝Panel Fasteners电梯螺丝Elevator Bolts四角头固定螺丝Square Set Screws大头马车螺丝Step Bolts单向螺丝One Way Lag Screws管夹螺丝Hose Clamp Screws不锈钢固定螺丝Stainless Steel Hex Socket Cap Screws不锈钢内六角螺丝Stainless Steel Hex Socket Cap Screws铰链螺丝Hinge Screws货柜螺丝Container Screws复合材料钻尾螺丝Bi-Metal Self Drilling Screws三角牙螺丝Trilobular Thread Screws高低牙螺丝High Low Screws夹板用螺丝Particle Board Screws马桶螺丝Toilet Closet Bolts特长螺丝Special Longer Screws建业螺丝Building Fasteners不锈钢六角螺丝Stainless Steel Hex Socket Cap Screws其它特殊螺丝Special Screws Or Bolts不锈钢特殊螺丝Special Stainless Steel Screws宽牙螺丝（粗牙螺丝）Coarse Thread Screws链带螺丝Collated Screws水泥螺丝Concrete Screws板模螺丝Construction Bolts锌蝶螺丝Die Cast Wing Screws; Zinc Alloy重型车螺丝Heavy Duty Wheel Hub Bolts内六角固定螺丝Hex Socket Set Screws复合材料用螺丝（夹板用）Particle Board Screws犁壁螺丝Plow Bolts不锈钢木螺丝Stainless Steel Wood Screws套挂螺栓及螺丝Toggle Bolts钛合金膨胀螺丝Titanium Alloy Expansion Bolts六角盖头螺帽Hex Cap Nuts六角锯齿螺帽Hex Serrated Nuts六角轮缘螺帽Hex Flange Nuts高脚螺帽Hex Coupling Nuts(High Nuts)圆螺帽Round Nuts四角螺帽Square Nuts管用螺帽Pipe Nuts轮壳螺帽Wheel Nuts蝶型螺帽Wing NutsU形螺帽U NutsT形螺帽T Nuts环首螺帽Eye Nuts齿形螺帽Kep Nuts齿花螺帽Clinch Nuts耐候钢六角重型螺帽Corten Steel Heavy Hex Nuts焊接螺帽Weld Nuts高张力螺帽Heigh Strength Nuts建业用螺帽Structural Nuts不锈钢螺帽Stainless Steel Nuts铜螺帽Brass Nuts铝螺帽Aluminum Nuts合金钢螺帽Alloy Steel Nuts重型车螺帽Heavy Duty Wheel Hub Nuts铁器焊接袋帽Acorn Cap Nuts金属预置扭矩式螺帽All-Metal Prevailing Torque Type Nuts壁虎螺帽Anchor Nuts大尺寸螺帽Big Size Nuts铁盖袋帽Closed End Acorn Nuts盘形华司螺帽Conical Washer Nuts铁盖+尼龙圈组合盖帽Din 986 Domed Cap Nuts突缘尼龙盖帽Flange Nylon Insert Lock Nuts平面华司螺帽Flat Waser Nuts六角割沟螺帽Hex Slotted Nut自锁螺帽Self-Locking Nuts制止螺帽Sliding NutsSln-自动防松螺帽Sln Self-Locking Nuts其它特殊螺帽Special Nuts弹簧螺帽Spring Nuts不锈钢突缘螺帽Stainless Steel Flange Nuts不锈钢六角轮缘尼龙螺帽Stainless Steel Flange Nylon Insert Lock Nuts 不锈钢六角重型螺帽Stainless Steel Heavy Hex Nuts不锈钢六角螺帽Stainless Steel Hex Nuts不锈钢尼龙嵌入螺帽Stainless Steel Nylon Insert Lock Nuts锌压属螺帽Zinc Die Casting Nuts普通六角螺帽Hex Nuts六角重型螺帽Heavy Hex Nuts薄型螺帽Hex Jam Nuts尼龙嵌入防松螺帽Nylon Insert Lock Nuts机械螺丝用六角螺帽Hex Machine Screw Nut合金钢线材盘元Alloy Steel Wire Rod球状化线材Annealing Wire And Rod黑铁丝Black Wire黄铜棒线Brass Wire And Rod磨光棒钢Bright Steel Bar(Hex/Round/Square)铜合金线Copper Alloy Wire线切割线E.D.M Cutting Wire快削钢线材盘元Free Cutting Steel Wire Rod线材Iron Or Steel Wire线材盘元Iron Or Steel Wire Rod洋白铜线Nickel Silver Wire磷青铜线Phosphate Bronze Wire不锈钢条棒Stainless Steel Bar(Round/Hex/Square)不锈钢冷锻线材Stainless Steel Cold Heading Wire不锈钢线(抽线后) Stainless Steel Draw Wire不锈钢线材Stainless Steel Wire不锈钢线材及盘元Stainless Steel Wire And Rod棒钢Steel Bar(Hex/Round/Square)转回90度碾线头机90讧evolving Wire Twisting Machine气动拉钉机Air Riveter各式螺丝类产品自动包装Automatic Packaging For All Kinds Of Packaging 自动包装机Automatic Packing Machine螺丝制造搓牙机械Automatic Thread Rolling Machine螺丝割尾加工机械Automatic Thread Slotting Machine螺丝制造成型机械Automatic Trimming Machine拉钉打头机Blind Rivet Heading Machine螺丝、螺帽成型机Bolt Formers,Nuts Formers,Headers螺丝、螺帽热处理Bolt Nut And Screws Heat Treatment螺丝、螺帽热处理炉Bolt Nut And Screws Heat Treatment Furnaces球状化电器炖炉Carburizing Furnace Vacuum And Bell Type Furnace超防锈复合瓷膜Ceramic Coating连续式光辉渗碳淬火炉Continuous Bright Carburizing Quenching Furnace 连续式光辉调质淬火炉Continuous Bright Hardening Quenching Furnace 中、高热镀锌光辉连续炉Continuous Bright Heat Treat Furnace连续式光辉热处理炉Continuous Type Bright Heat Treatment Furnace螺丝割尾及特殊割遘加工Machine Screw Shank Slotting螺丝钻孔加工Screw Shank Drilling鸡眼上下模Eyelets Dies一般线材、盘元、退火炉General Wire,Wire Rod,Annealing Furnace倒立式滑落型伸线机Handstand Type Wire Drawing Machine十字冲模Header Punches In Various Drives成型冲模Header Punches In Various Drives螺丝打头机Heading Machine螺丝制造高速搓牙机械High Speed Automatic Thread Rolling Machine高中低周波感应加热炉High,Medium,Low Frequency Induction Heater空心打头机Hollow Heading Machine热浸镀锌螺丝、螺帽Hot Dip Galvanizing Bolts And Nuts机械镀锌Mechanical Galvanized迷你成型机Mini-Formers成品自动收线机Non-Stop Coiler精抽自动收线机Non-Stop Coiler(Skinpass)螺帽模Nut Forming Dies螺帽成型模Nuts Formers特殊零件成型机Parts Forming Maching冲模Punch Dies冲子Punch Pins罗拉成型机Rollers Formers机(踏)车用螺丝成型机Screw For Motorcycle Or Bicycle Heading Machine止付螺丝成型机Set Screws Formers套高成型机Sockets Formers一般线材、盘元、螺丝合金炖炉Spheroidizing Bright Annealing Furnace球状化热处理炉Spheroidizing Heat Treatment Furnace攻牙机Tapping Machine螺丝攻、车刀、模具Taps Dies And Tools搓牙机铁屑分离装置Thread Chip Separator滚牙轮Thread Rolling Dies牙板Thread Rolling Dies Plates精密油压滚牙机Hydraulic Thread Rolling Machines模具Tools六角整头模Trimming Dies Hexagan碳化钨模具Tungsten Carbide Die镀钛处理(Tin)专业加工服务Tin Hard Coating For Cutting Tools And Punch By Pvd 电镀化学原料Various Electroplating Chemicals环规校正Calibration For Ring Gage环规、牙规、三线规校正Calibration For Ring Gage, Athread Gage, 3 Wire Gage 螺丝、螺帽品检量测仪器Fasteners Inspection And Measurement Instruments螺丝、螺帽成型攻牙专用油Forming And Tapping Oils For Bolts And Nuts Formers 螺丝、螺帽五金等检验Insptection Services For Fasteners And Hardware德国schatz扭力机代理Representative Of Schatz Torque MachinIso品质保证系统Iso Quality Assurance System生产管理系统Production Control System物料管理系统Material Control System齿轮Gears不锈钢牙条棒Stainless Steel Hread Rod马达轴承轴心组件Bearing Shaft(Motor)轴承轴心Bearing Shaft开口铆钉Blind Rivets长形拉帽Blind Rivet Nuts拉帽Blind Nuts拉钉Blind Rivets实心梢Clevis Pins And Straight Pins弹片Clips卷钉Coil Nails冷锻零件Cold Forming Part开口销Cotter PinsE型环E-Rings膨胀螺栓Expansion Anchor Bolts鸡眼钉Eyelets RivetsR型销Snap Pins闸、锁Latches And Keeper Assembleds其它特殊铆钉Other Specil Rivets销Pins格式管夹、管束Pipe Hanger铆钉Rivets螺旋锔及螺旋圈Screw Hook And Screw Rings中空钉Semi-Tubular Rivet开叉钉Split Drive Anchors弹簧华司Spring Washers弹簧蝴蝶夹Spring Wings不锈钢华司Stainlesssteel Washers钢铁钉Steel And Iron Nails搓牙铁钉Thread Nails钛合金铆钉Titaium Alloy Rivets管形铆钉Tubular Rivets华司Washers真空热处理Vacuum Heat Treatment螺丝、螺帽、五金、Diy扣件Fasteners合金钢工具Alloy Steel Tools螺栓模Bolt Heading Dies手动拉钉钳Hand Riveter船舶链Anchor Chain脚踏车链锁Bicycle Chain Locks螺丝起子Bit罗拉Chain Roller特殊铆合扣件Collars(A Blindfastener For Huck Intl)装饰链Decorative Chains自攻螺纹衬套Ensat Threaded Inserts六角扳手Hexagon Keys超音螺纹压入式螺纹自动锁扣Threaded Inserts For Plastic Injection Mouldeings 汽车特殊杆接件Special Auto-Mobile Fastener As Your Needs螺纹护套Recoil Inserts链条用滚子Roller For Roller Chain金属板镶嵌组件及自动夹扣组件Sheet Metal Fasteners工具套筒组件Socket Wrench Sets不锈钢链Stainless Steel Chains轭子T-Yoke轮胎链Tire Chains狗链Dog Chains喇叭头轭铁U-Yoke,T-Yoke For Speaker不锈钢输送带轮用轨道Stainless Wheel's Rack For Transporter工业用链Industrial Steel Link Chains拖链安全链Tow Chains And Safety Chains机车离合器零件Manufacture Of Motorcycle's Cvt Parts牙条棒Thread Rod。
紧固件英文对照
紧固件英文对照吊环螺母LIFTING EYE NUTS公制外型的吋制螺母METRIC DIMENSIONS NUTS WITH UNC OR BSW THREAD德制吊环螺母LIFTING EYE NUTS DIN582六角法兰面螺母HEXAGON NUTS WITH FLANGE德制六角法兰面螺母HEXAGON NUTS WITH FLANGE DIN6923美制六角法兰面螺母HEX FLANGE NUTS IFI D-21蝶形螺母WING NUTS DIN315德制非金属嵌件六角锁紧螺母PREVAILING TORQUE TYPE HEXAGON THIN NUTS WITH NONMETALLIC INSERT DIN985德制金属嵌件六角锁紧螺母ALL-METAL PREVAILING TORQUE TYPE HEXAGON NUTS DIN980焊接六角螺母HEXAGON WELD NUTS DIN929六角开槽螺母HEXAGON SLOTTED NUTS六角开槽螺母HEXAGON SLOTTED NUTS DIN935六角开槽薄螺母HEXAGON THIN SLOTTED NUTS DIN937六角开槽薄螺母HEXAGON THIN SLOTTED NUTS DIN979盖形螺母HEXAGON CAP NUTS盖形螺母HEXAGON CAP NUTS DIN917盖形螺母HEXAGON DOMED CAP NUTS DIN986盖形螺母HEXAGON DOMED CAP NUTS DIN1587弹簧垫圈SPRING WASHERS德制弹簧垫圈SPRING LOCK WASHERS DIN127英制弹簧垫圈SPRING LOCK WASHERS B.S.美制弹簧垫圈LOCK WASHERS IFI L-9(K-13)平垫圈PLAIN WASHERS德制垫圈WASHERS (Grade A) DIN125德制垫圈WASHERS (Grade C) DIN126美制平垫圈（窄型）PLAIN WASHERS (NARROW) IFI L-2(K-4)美制平垫圈（宽型）PLAIN WASHERS (WIDE) IFI L-2(K-4)美制淬火垫圈HARDENED STEEL WASHERS ASTM F436开口销SPLIT PINS德制开口销SPLIT PINS DIN94美制开口销COTTER PINS L-38开口销SPLIT PINS ISO1234英制开口销COTTER PINS B.S.抽芯铆钉BLIND RIVET抽芯铆钉BLIND RIVET封闭形抽芯铆钉SEALED TYPE ALUMINIUM BLIND RIVET机器螺钉MACHINE SCREWS英制镀锌瓦楞螺闩GALVANIZED ROOFING BOLTS & NUTS B.S.德制瓦楞螺闩ROOFING BOLTS & NUTS德制开槽圆柱头螺钉SLOTTED CHEESE HEAD SCREWS DIN84德制开槽盘头螺钉SLOTTED PAN HEAD SCREWS DIN85美制开槽盘头机螺钉SLOTTED PAN HEAD MACHINE SCREWS IFI I-22(F-24)德制十字槽球面圆柱头螺钉CROSS RECESSED RAISED CHEESE HEAD SCREWS DIN7985美制十字槽盘头机螺钉CROSS RECESSED PAN HEAD MACHINE SCREWS IFI I-23(F-25)德制开槽沉头螺钉SLOTTED COUNTERSUNK HEAD SCREWS DIN963美制开槽沉头机螺钉SLOTTED FLAT COUNTERSUNK HEAD MACHINE SCREWS IFI I-6(F-8)德制十字槽沉头螺钉CROSS RECESSED COUNTERSUNK FLAT HEAD SCREWS DIN965美制十字槽沉头机螺钉CROSS RECESSED FLAT COUNTERSUNK HEAD MACHINE SCREWS IFI I-7(F-9)德制开槽半沉头螺钉SLOTTED RAISED COUNTERSUNK HEAD SCREWS DIN964美制开槽半沉头机螺钉SLOTTED OVAL COUNTERSUNK HEAD MACHINE SCREWS IFI I-16(F-18)德制十字槽半沉头螺钉CROSS RECESSED RAISE COUNTERSUNK HEAD SCREWS DIN966美制十字槽半沉头机螺钉CROSS RECESSED OVAL COUNTERSUNK HEAD MACHINE SCREWS IFI I-17（F-19）美制开槽扁圆头机螺钉SLOTTED TRUSS HEAD MACHINE SCREWS IFI I-26(F-28)美制十字槽扁圆头机螺钉CROSS RECESSED TRUSS HEAD MACHINE SCREWS IFI I-27(F-29)AT吊装螺栓ACOUSTICAL TOGGLES木螺钉WOOD SCREWS德制开槽半沉头木螺钉SLOTTED RAISED COUNTERSUNK HEAD WOOD SCREWS DIN95美制开槽半沉头木螺钉OVAL COUNTERSUNK HEAD WOOD SCREWS IFI J-38(F-58) 英制开槽半沉头木螺钉SLOTTED OVAL HEAD WOOD SCREWS B.S.1210德制十字槽半沉头木螺钉CROSS RECESSED RAISED COUNTERSUNK HEAD WOOD SCREWS DIN7995美制十字槽半沉头木螺钉OVAL COUNTERSUNK HEAD WOOD SCREWS IFI J-39(F-59) 英制十字槽半沉头木螺钉SLOTTED OVAL HEAD WOOD SCREWS B.S.1210德制开槽半圆头木螺钉SLOTTED ROUND HEAD WOOD SCREWS DIN96英制开槽圆头木螺钉SLOTTED ROUND HEAD WOOD SCREWS B.S.1210德制十字槽半圆头木螺钉CROSS RECESSED ROUND WOOD SCREWS DIN7996德制开槽沉头木螺钉SLOTTED COUNTERSUNK HEAD WOOD SCREWS DIN97美制开槽沉头木螺钉FLAT COUNTERSUNK HEAD WOOD SCREWS IFI J-36(F-56)英制开槽沉头木螺钉SLOTTED COUNTERSUNK HEAD WOOD SCREWS B.S.1210AE木螺钉ACOUSTICALL EYELAGS德制十字槽沉头木螺钉FLAT COUNTERSUNK HEAD WOOD SCREWS DIN7997美制十字槽沉头木螺钉CROSS RECESSED COUNTERSUNK HEAD WOOD SCREWS IFI J-37(F-57)英制十字槽沉头木螺钉CROSS RECESSED COUNTERSUNK HEAD WOOD SCREWS B.S.1210德制六角头木螺钉HEXAGON HEAD WOOD SCREWS DIN571美制六角头木螺钉HEX LAG SCREWS IFI C-18米字槽双线木螺钉POZIDRIVE TWINFAST WOOD SCREWS B.S.织维板螺钉CHIPBOARD SCREWS HARDENED织维板螺钉CHIPBOARD SCREWS HARDENED大螺距带筋织维板螺钉CHIPBOARD SCREWS WITH RIBS UNDER THE HEAD高低牙加硬螺钉FERMACELL SCREWS WITH RIBS UNDER THE HEAD自攻螺钉TAPPING SCREWS德制开槽盘头自攻螺钉PAN HEAD TAPPING SCREWS WITH SLOT DIN7971美制开槽盘头自攻螺钉SLOTTED PAN HEAD TAPPING SCREWS IFI H-38(E-34)德制十字槽盘头自攻螺钉CROSS RECESSED PAN HEAD TAPPING SCREWS DIN7981 美制十字槽盘头自攻螺钉CROSS RECESSED PAN HEAD TAPPING SCREWS IFI H-39(E-35)德制开槽沉头自攻螺钉COUNTERSUNK HEAD TAPPING SCREWS WITH SLOT DIN7972美制开槽沉头自攻螺钉SLOTTED FLAT COUNTERSUNK HEAD TAPPING SCREWS IFI H-24(E-20)德制开槽半沉头自攻螺钉RAISED COUNTERSUNK HEAD TAPPING SCREWS WITH SLOT DIN7973美制开槽半沉头自攻螺钉SLOTTED OVAL COUNTERSUNK HEAD TAPPING SCREWS IFI H-32(E-28)德制十字槽半沉头自攻螺钉CROSS RECESSED RAISED COUNTERSUNK HEAD TAPPING SCREWS DIN7983美制十字槽半沉头自攻螺钉CROSS RECESSED OVAL COUNTERSUNK HEAD TAPPING SCREWS IFI H-33(E-39)双线快牙干壁-S型十字槽喇叭头DRY WALL SCREWS TYPE S PHILLIPS RECESSED BUGLE HEAD TWINFAST粗牙干壁螺钉DRY WALL SCREWS德制十字槽沉头自攻螺钉CROSS RECESSED COUNTERSUNK HEAD TAPPING SCREWS DIN7982美制十字槽沉头自攻螺钉CROSS RECESSED FLAT COUNTERSUNK HEAD TAPPING SCREWS IFI H-25(E-21)十字槽扁圆头带垫面自攻螺钉CROSS RECESSED PAN HEAD TAPPING SCREWSWITH COLLAR DIN968六角头带垫面自攻螺钉HEXAGON WASHER HEAD TAPPING SCREWS DIN6928自钻自攻螺钉SELF-DRILLING TAPPING SCREWS DIN7504螺栓包装PACKING OF BOLTS六角头螺栓HEXAGON HEAD BOLTS DIN931 DIN601 DIN7990六角头螺栓HEXAGON HEAD BOLTS DIN931 DIN601 DIN7990六角头螺栓HEXAGON HEAD BOLTS ISO4014圆头方颈螺栓MUSHROOM HEAD SQUARE NECK BOLTS DIN603圆头方颈螺栓ROUND HEAD SQUARE NECK BOLTS IFI C-40六角螺钉包装>PACKING OF HEXAGON HEAD SCREWS六角头螺钉HEXAGON HEAD SCREWS DIN933 DIN558六角头螺钉HEXAGON HEAD SCREWS DIN933 DIN558六角头螺钉HEXAGON HEAD SCREWS ISO4017六角头螺钉HEX CAP SCREWS IFI C-10(A-10)内六角螺钉包装PACKING OF HEXAGON SOCKET HEAD CAP SCREWS DIN912内六角沉头螺钉包装PACKING OF HEXAGON SOCKET COUNTERSUNK HEAD CAP SCREWS DIN7991螺母包装PACKING OF NUTS六角螺母HEXAGON NUTS DIN934，DIN555六角螺母HEXAGON NUTS AS1112，ISO4032六角薄螺母HEXAGON THIN NUTS DIN439六角薄螺母HEXAGON THIN NUTS DIN936尼龙锁紧螺母NYLON JAM NUTS DIN985六角开槽螺母HEX SLOTTED NUTS DIN935方形薄螺母SQUARE THIN NUTS DIN562方螺母SQUARE NUTS DIN557蝶形螺母WING NUTS DIN315六角螺母HEXAGON NUTS DIN5587吊环螺母LIFTING EYE NUTS DIN582六角法兰面螺母HEXAGON NUTS WITH FLANG DIN6923六角螺母HEXAGON NUTS BS1768厚六角螺母HEXAGON THICK NUTS BS1768六角螺母HEXAGON NUTS BS916六角螺母HEXAGON NUTS IFI D-5(D-6)六角锁紧螺母HEX JAM NUTS IFI D-5(D-6)重型六角螺母HEAVY HEX NUTS A325, IFI D-14螺母包装PACKING OF NUTS六角开槽螺母HEX SLOTTED NUTS DIN937六角盖型螺母HEXAGON DOMED CAP NUTS DIN1587焊接六角螺母HEXAGON WEID NUTS DIN929垫圈包装PACKING OF WASHERS垫圈WASHERS DIN125,DIN126弹簧垫圈SPRING LOCK WASHERS DIN127弹簧垫圈LOCK WASHERS IFI L-9(K-13)机螺钉包装PA CKING OF MACHINE SCREWS开槽圆柱头螺钉SLOTTED CHEESE HEAD SCREWS DIN84开槽沉头螺钉SLOTTED COUNTERSUNK HEAD SCREWS DIN963开槽盘头螺钉SLOTTED PAN HEAD SCREWS DIN85十字槽球面圆柱头螺钉CROSS RECESSED RAISED CHEESE HEAD SCREWS DIN7985自攻螺钉包装PACKING OF TAPPING SCREWS开槽、十字槽沉头自攻螺钉COUNTERSUNK HEAD TAPPING SCREWS DIN7972, DIN7982开槽、十字槽盘头自攻螺钉PAN HEAD TAPPING SCREWS DIN7971, DIN7981木螺钉包装PACKING OF WOOD SCREWS开槽半沉头木螺钉SLOTTED RAISED COUNTERSUNK HEAD WOOD SCREWS DIN95 开槽半圆头木螺钉SLOTTED ROUND HEAD WOOD SCREWS DIN96开槽沉头木螺钉SLOTTED COUNTERSUNK HEAD WOOD SCREWS DIN97开槽沉头木螺钉SLOTTED COUNTERSUNK HEAD WOOD SCREWS B.S.1210开槽半圆头木螺钉SLOTTED ROUND HEAD WOOD SCREWS B.S.1210六角头木螺钉HEXAGON HEAD WOOD SCREWS DIN571织维板螺钉包装PACKING OF CHIPBOARD SCREWS织维板螺钉CHIPBOARD SCREWS HARDENED双线快牙干壁螺钉DRY WALL SCREWS TWINFAST。
紧固件-中英文对照
紧固件-中英文对照No. 英文单词简写中文1 screw scr 螺丝2 nut nut 螺母3 washer wash 垫圈4 head hd 头5 thread thre 螺纹6 coating coat 镀层7 rivet riv 铆钉8 standoff stdoff 内外六角钉9 driver driv 穴10 hexagon hexa 六角11 tooth tooth 齿12 lock lck 锁13 spring spr 弹簧14 wave wave 波浪型15 pitch pitch 牙距16 partial thread PT 半螺纹17 PT PT 一种螺纹形式18 Full Thread FT 全螺纹19 silver silv 银20 cone cone 锥形21 Eco-syn Eco 30度牙的一种螺纹22 Thread Forming TF 自攻螺纹23 Self Tapping self tapp 自切屑螺纹24 pin pin 销25 shaft Shaf 轴26 steel St 铁27 stainless steel SS 不锈钢28 Brass(Cu) Bras(Cu) 铜29 Aluminum AL 铝30 Rubber Rub 橡胶31 machine screw mech scr 机制螺丝32 SEM screw SEM Scr 组合螺丝33 Material material 材料34 Grade GD 等级35 Finish Finish 表面处理36 Point Point 点37 Clamp Clam 夹子38 internal Int 内39 external ext 外40 thickness / 厚度41 length / 长度42 hole / 孔43 Metric Metcric 公制44 DIN / 德标45 ANSI / 美标46 JIS / 日标螺丝相关参数英语对照A: Machine Screw: 机械螺丝B: Tapping Screw: 自攻螺丝(分使用于金属与使用于塑料二种)B-1: Sheet Metal Tapping Screw. (铁板牙自攻螺丝)B-2: Plastic Tapping Screw. ( 塑料用, 自攻螺丝)C: Wooden Screw : 木工螺丝D: Drywall Screw : 水泥墙螺丝常见螺丝材质:a.Low Carbon Steel :低碳钢b. SS-304 : Stainless Steel 304c. SS-302: Stainless Steel 302 :结构韧性较好d. Aluminum 5052 :铝合金5052d. Brass: 黄铜e. Bronze: 青铜f. UNS C11000 Copper: 锑铜Finish Code: 外观处理规格Head Code: 头部外型螺丝型号Drive Code: 头部剖沟,特征型号Length Code: 螺丝长度(mm)A-1: Thread Code: 螺丝型号A-2: Length Code: 螺丝长度:A-3: Drive Code/ 头部剖沟,特征.a. Slotted: 一字( Minus )b. Phillips: 十字( Plus )c. Phil-Slot: 一字/十字d. Hex Scoket: 内六角e. One Way: 单向(只可锁入,不可退出) A-4: Head Code/ 头部外型.a. Flat: 平头(锁入后,顶部与工作件齐平)b. Oval: 色拉头c. Round: 圆头d. Pan: 圆扁头e. Truss: 大圆扁头f. Hex : 六角头A-5: Finish Code/ 外观处理.a. Z: Zine-Plated: 镀锌b. Ni: Ni-Plated: 镀镍c. Tin-Plated: 镀锡d. Zine Plated / Green Iridite: 镀锌绿膜处理.e. Radiant Plated: 镀五彩f. Passivate: 抗氧化处理.g. Alodial Finish: 无外观处理螺纹大径：Major Diam螺纹中径：Pitch diam螺纹底径：Minor diam通止规：Go/No go gage机械性能：mechanical and physical propertiesunified thread 统一英制螺纹Lustrate hydrogen after galvanizing to avoid hydrogen embrittlement 镀后去氢，防止氢脆Case carburization 表面渗碳With across flats 对边With across corners 对角Radius of fillet:头下圆角Transition thread length 过度螺纹Wrenching height 扳拧高度Rockwell 铬氏硬度Vickers 维氏硬度Brinell 布氏硬度Metallography microscope 金相显微镜Salt spray device 盐雾试验箱Tensile testing machine 拉力试验机Cold forming 冷打Hot forging 红镦P C 8 = property class 8 机械性能8级原材料：Raw material球化退火：Annealing冷拔：Drawing冷镦：Forming机加工：Machining螺纹成型：Roll Threading热处理：heat-treatment表面处理：finish去氢：Lustrating hydrogen检验：Inspection包装：Packing入库：Stocking车床：lathe磨制：grinding红打：hot forging冲压：punchingDiameter 直径Length 长度各类紧固件标准件产品英语翻译对照插片壁虎Steel Ceiling Anchors内迫壁虎Drop in Anchors碳钢锤钉壁虎Steel Hit Anchors碳钢六角螺帽Steel Hex Coupling Nuts强力车修壁虎Wedge Anchors外迫壁虎Cut Anchors化学壁虎Chemical Anchors不锈钢重载胀栓Heavy Duty Expansion Anchors鱼眼壁虎企眼长螺帽Tie Wire Anchors锌合金打入式壁虎Hammer Drive Anchors弹簧螺帽Strut Nuts兰花夹系列Toggle Bolts (Spring Toggle & Gravity Toggle)门窗、地板专用壁虎Nylon Frame Anchors or Metalframe Anchors石膏板中空壁虎Hollow Wall Anchors套管式壁虎Sleeve Anchors打入式壁虎鱼形尼龙壁虎Nylon Frame Harmmer Fixing (Nylon Hammer Drive Anchors)强力式锤钉壁虎Hit Anchors电梯壁虎Bolt Anchors重载壁虎Heavy duty anchors两片夹Loxin Masonry Anchors定位螺栓Set Bolts长型兰花夹Short Strap Anchors工具棒Drop in Setting Tools象脚壁虎Elephant foot anchors水泥预埋件Concrete Insert翻边胀轴Drop in Anchor with Lip冲件Legs Drywall Anchors六角盖头螺帽Hex Cap Nuts六角锯齿螺帽Hex Serrated Nuts六角轮缘螺帽Hex Flange Nuts高脚螺帽Hex Coupling Nuts(High Nuts)圆螺帽Round Nuts四角螺帽Square Nuts管用螺帽Pipe Nuts轮壳螺帽Wheel Nuts蝶型螺帽Wing NutsU形螺帽U NutsT形螺帽T Nuts环首螺帽Eye Nuts齿形螺帽Kep Nuts齿花螺帽Clinch Nuts耐候钢六角重型螺帽Corten Steel Heavy Hex Nuts焊接螺帽Weld Nuts高张力螺帽Heigh Strength Nuts建业用螺帽Structural Nuts不锈钢螺帽Stainless Steel Nuts铜螺帽Brass Nuts铝螺帽Aluminum Nuts合金钢螺帽Alloy Steel Nuts重型车螺帽Heavy Duty Wheel Hub Nuts铁器焊接袋帽Acorn Cap Nuts金属预置扭矩式螺帽All-Metal Prevailing Torque Type Nuts壁虎螺帽Anchor Nuts大尺寸螺帽Big Size Nuts铁盖袋帽Closed End Acorn Nuts盘形华司螺帽Conical Washer Nuts铁盖+尼龙圈组合盖帽Din 986 Domed Cap Nuts突缘尼龙盖帽Flange Nylon Insert Lock Nuts平面华司螺帽Flat Waser Nuts六角割沟螺帽Hex Slotted Nut自锁螺帽Self-Locking Nuts制止螺帽Sliding NutsSln-自动防松螺帽Sln Self-Locking Nuts其它特殊螺帽Special Nuts弹簧螺帽Spring Nuts不锈钢突缘螺帽Stainless Steel Flange Nuts 不锈钢六角轮缘尼龙螺帽Stainless Steel Flange Nylon Insert Lock Nuts不锈钢六角重型螺帽Stainless Steel Heavy Hex Nuts不锈钢六角螺帽Stainless Steel Hex Nuts不锈钢尼龙嵌入螺帽Stainless Steel Nylon Insert Lock Nuts普通六角螺帽Hex Nuts六角重型螺帽Heavy Hex Nuts薄型螺帽Hex Jam Nuts尼龙嵌入防松螺帽Nylon Insert Lock Nuts机械螺丝用六角螺帽Hex Machine Screw Nut 六角螺丝(栓) Hex Head Cap Screws(Hex Bolts)六角机械螺丝Hex Head Machine Bolts六角木牙螺丝Hex Lag Bolts四角螺丝Square Head BoltsT头螺丝T Head Bolts马车螺丝Carriage Bolts环首螺丝Eye Bolts内六角孔螺丝Hex Socket Cap Screws固定螺丝Set Screws螺椿栓Stud Bolts螺旋椿Screw Studs轮壳螺栓Wheel Bolts翼形螺丝Wing Screws自攻螺丝Self Tapping Screws自削螺丝Thread Cutting Screws钻尾螺丝Self Drilling Screws机械螺丝Machine Screws木螺丝Wood Screws家具螺丝Furniture Screws塑板螺丝Chipboard Screws墙用螺丝Drywall Screws基础螺栓Foundation BoltsU型螺栓U Bolts勾头螺栓Hook Bolts套挂螺丝Toggle Bolts突缘螺丝Flange Bolts轨道螺栓(鱼尾螺丝) Track Bolts耐候钢螺丝Corten Steel Heavy Hex Bolts扭矩控制螺栓T.C.Bolts高张力螺栓High Strength Bolts剪力钉(焊接螺丝) Welding Studs螺丝附华司组合Screws And Washers Assembled(Sems)大尺寸螺栓Big Size Bolts不锈钢小螺丝Stainless Steel Sheet Metal Screws不锈钢大螺丝Stainless Steel Bolts铝螺丝Aluminum Screws合金钢螺丝Alloy Steel Screws电子螺丝Electronic Screws微小精密螺丝Micro Screws塑料螺丝Plastic Screws复合材料用螺丝Particle Board Screws钛合金螺丝Titanium Alloy Bolts钛、锆、钼、铌等螺丝、零件、材料Ti,Zr,Mo,Nb Pare Metal Bolts Parts拇指螺丝Thumb Screws双头牙螺丝Double End Screws Hanger Bolt 车辆(汽车)螺丝、螺帽Automotive Fasteners 航天用螺丝Aerospace Fasteners飞机特殊扣件Source Control Bolts拉栓Blind Bolts面板螺丝Panel Fasteners电梯螺丝Elevator Bolts四角头固定螺丝Square Set Screws大头马车螺丝Step Bolts单向螺丝One Way Lag Screws管夹螺丝Hose Clamp Screws不锈钢固定螺丝Stainless Steel Hex Socket Cap Screws不锈钢内六角螺丝Stainless Steel Hex Socket Cap Screws铰链螺丝Hinge Screws货柜螺丝Container Screws复合材料钻尾螺丝Bi-Metal Self Drilling Screws三角牙螺丝Trilobular Thread Screws高低牙螺丝High Low Screws夹板用螺丝Particle Board Screws马桶螺丝Toilet Closet Bolts特长螺丝Special Longer Screws建业螺丝Building Fasteners不锈钢六角螺丝Stainless Steel Hex Socket Cap Screws其它特殊螺丝Special Screws Or Bolts不锈钢特殊螺丝Special Stainless Steel Screws宽牙螺丝（粗牙螺丝）Coarse Thread Screws 链带螺丝Collated Screws水泥螺丝Concrete Screws板模螺丝Construction Bolts锌蝶螺丝Die Cast Wing Screws; Zinc Alloy 重型车螺丝Heavy Duty Wheel Hub Bolts内六角固定螺丝Hex Socket Set Screws复合材料用螺丝（夹板用）Particle Board Screws犁壁螺丝Plow Bolts不锈钢木螺丝Stainless Steel Wood Screws 套挂螺栓及螺丝Toggle Bolts钛合金膨胀螺丝Titanium Alloy Expansion Bolts六角盖头螺帽Hex Cap Nuts六角锯齿螺帽Hex Serrated Nuts六角轮缘螺帽Hex Flange Nuts高脚螺帽Hex Coupling Nuts(High Nuts)圆螺帽Round Nuts四角螺帽Square Nuts管用螺帽Pipe Nuts轮壳螺帽Wheel Nuts蝶型螺帽Wing NutsU形螺帽U NutsT形螺帽T Nuts环首螺帽Eye Nuts齿形螺帽Kep Nuts齿花螺帽Clinch Nuts耐候钢六角重型螺帽Corten Steel Heavy Hex Nuts焊接螺帽Weld Nuts高张力螺帽Heigh Strength Nuts建业用螺帽Structural Nuts不锈钢螺帽Stainless Steel Nuts铜螺帽Brass Nuts铝螺帽Aluminum Nuts合金钢螺帽Alloy Steel Nuts重型车螺帽Heavy Duty Wheel Hub Nuts铁器焊接袋帽Acorn Cap Nuts金属预置扭矩式螺帽All-Metal Prevailing Torque Type Nuts壁虎螺帽Anchor Nuts大尺寸螺帽Big Size Nuts铁盖袋帽Closed End Acorn Nuts盘形华司螺帽Conical Washer Nuts铁盖+尼龙圈组合盖帽Din 986 Domed CapNuts突缘尼龙盖帽Flange Nylon Insert Lock Nuts平面华司螺帽Flat Waser Nuts六角割沟螺帽Hex Slotted Nut自锁螺帽Self-Locking Nuts制止螺帽Sliding NutsSln-自动防松螺帽Sln Self-Locking Nuts其它特殊螺帽Special Nuts弹簧螺帽Spring Nuts不锈钢突缘螺帽Stainless Steel Flange Nuts 不锈钢六角轮缘尼龙螺帽Stainless Steel Flange Nylon Insert Lock Nuts不锈钢六角重型螺帽Stainless Steel Heavy Hex Nuts不锈钢六角螺帽Stainless Steel Hex Nuts不锈钢尼龙嵌入螺帽Stainless Steel Nylon Insert Lock Nuts锌压属螺帽Zinc Die Casting Nuts普通六角螺帽Hex Nuts六角重型螺帽Heavy Hex Nuts薄型螺帽Hex Jam Nuts尼龙嵌入防松螺帽Nylon Insert Lock Nuts机械螺丝用六角螺帽Hex Machine Screw Nut合金钢线材盘元Alloy Steel Wire Rod球状化线材Annealing Wire And Rod黑铁丝Black Wire黄铜棒线Brass Wire And Rod磨光棒钢Bright Steel Bar(Hex/Round/Square)铜合金线Copper Alloy Wire线切割线 E.D.M Cutting Wire快削钢线材盘元Free Cutting Steel Wire Rod 线材Iron Or Steel Wire线材盘元Iron Or Steel Wire Rod洋白铜线Nickel Silver Wire磷青铜线Phosphate Bronze Wire不锈钢条棒Stainless Steel Bar(Round/Hex/Square)不锈钢冷锻线材Stainless Steel Cold Heading Wire不锈钢线(抽线后) Stainless Steel Draw Wire 不锈钢线材Stainless Steel Wire不锈钢线材及盘元Stainless Steel Wire And Rod棒钢Steel Bar(Hex/Round/Square)转回90度碾线头机90讧evolving Wire Twisting Machine气动拉钉机Air Riveter各式螺丝类产品自动包装Automatic Packaging For All Kinds Of Packaging自动包装机Automatic Packing Machine螺丝制造搓牙机械Automatic Thread Rolling Machine螺丝割尾加工机械Automatic Thread Slotting Machine螺丝制造成型机械Automatic Trimming Machine拉钉打头机Blind Rivet Heading Machine螺丝、螺帽成型机Bolt Formers,Nuts Formers,Headers螺丝、螺帽热处理Bolt Nut And Screws Heat Treatment螺丝、螺帽热处理炉Bolt Nut And Screws Heat Treatment Furnaces球状化电器炖炉Carburizing Furnace Vacuum And Bell Type Furnace超防锈复合瓷膜Ceramic Coating连续式光辉渗碳淬火炉Continuous Bright Carburizing Quenching Furnace连续式光辉调质淬火炉Continuous Bright Hardening Quenching Furnace中、高热镀锌光辉连续炉Continuous Bright Heat Treat Furnace连续式光辉热处理炉Continuous Type Bright Heat Treatment Furnace螺丝割尾及特殊割遘加工Machine Screw Shank Slotting螺丝钻孔加工Screw Shank Drilling鸡眼上下模Eyelets Dies一般线材、盘元、退火炉General Wire,Wire Rod,Annealing Furnace倒立式滑落型伸线机Handstand Type Wire Drawing Machine十字冲模Header Punches In Various Drives 成型冲模Header Punches In Various Drives 螺丝打头机Heading Machine螺丝制造高速搓牙机械High Speed Automatic Thread Rolling Machine高中低周波感应加热炉High,Medium,Low Frequency Induction Heater空心打头机Hollow Heading Machine热浸镀锌螺丝、螺帽Hot Dip Galvanizing Bolts And Nuts机械镀锌Mechanical Galvanized迷你成型机Mini-Formers成品自动收线机Non-Stop Coiler精抽自动收线机Non-Stop Coiler(Skinpass) 螺帽模Nut Forming Dies螺帽成型模Nuts Formers特殊零件成型机Parts Forming Maching冲模Punch Dies冲子Punch Pins罗拉成型机Rollers Formers机(踏)车用螺丝成型机Screw For Motorcycle Or Bicycle Heading Machine止付螺丝成型机Set Screws Formers套高成型机Sockets Formers一般线材、盘元、螺丝合金炖炉SpheroidizingBright Annealing Furnace球状化热处理炉Spheroidizing Heat Treatment Furnace攻牙机Tapping Machine螺丝攻、车刀、模具Taps Dies And Tools搓牙机铁屑分离装置Thread Chip Separator 滚牙轮Thread Rolling Dies牙板Thread Rolling Dies Plates精密油压滚牙机Hydraulic Thread Rolling Machines模具Tools六角整头模Trimming Dies Hexagan碳化钨模具Tungsten Carbide Die镀钛处理(Tin)专业加工服务Tin Hard Coating For Cutting Tools And Punch By Pvd电镀化学原料Various Electroplating Chemicals环规校正Calibration For Ring Gage环规、牙规、三线规校正Calibration For Ring Gage, Athread Gage, 3 Wire Gage螺丝、螺帽品检量测仪器Fasteners Inspection And Measurement Instruments螺丝、螺帽成型攻牙专用油Forming And Tapping Oils For Bolts And Nuts Formers螺丝、螺帽五金等检验Insptection Services For Fasteners And Hardware德国schatz扭力机代理Representative Of Schatz Torque MachinIso品质保证系统Iso Quality Assurance System生产管理系统Production Control System物料管理系统Material Control System齿轮Gears不锈钢牙条棒Stainless Steel Hread Rod马达轴承轴心组件Bearing Shaft(Motor)轴承轴心Bearing Shaft开口铆钉Blind Rivets长形拉帽Blind Rivet Nuts拉帽Blind Nuts拉钉Blind Rivets实心梢Clevis Pins And Straight Pins弹片Clips卷钉Coil Nails冷锻零件Cold Forming Part开口销Cotter PinsE型环E-Rings膨胀螺栓Expansion Anchor Bolts鸡眼钉Eyelets RivetsR型销Snap Pins闸、锁Latches And Keeper Assembleds其它特殊铆钉Other Specil Rivets销Pins格式管夹、管束Pipe Hanger铆钉Rivets螺旋锔及螺旋圈Screw Hook And Screw Rings中空钉Semi-Tubular Rivet开叉钉Split Drive Anchors弹簧华司Spring Washers弹簧蝴蝶夹Spring Wings不锈钢华司Stainlesssteel Washers钢铁钉Steel And Iron Nails搓牙铁钉Thread Nails钛合金铆钉Titaium Alloy Rivets管形铆钉Tubular Rivets华司Washers真空热处理Vacuum Heat Treatment螺丝、螺帽、五金、Diy扣件Fasteners合金钢工具Alloy Steel Tools螺栓模Bolt Heading Dies手动拉钉钳Hand Riveter船舶链Anchor Chain脚踏车链锁Bicycle Chain Locks螺丝起子Bit罗拉Chain Roller特殊铆合扣件Collars(A Blindfastener For Huck Intl)装饰链Decorative Chains自攻螺纹衬套Ensat Threaded Inserts六角扳手Hexagon Keys超音螺纹压入式螺纹自动锁扣Threaded Inserts For Plastic Injection Mouldeings汽车特殊杆接件Special Auto-Mobile Fastener As Your Needs螺纹护套Recoil Inserts链条用滚子Roller For Roller Chain金属板镶嵌组件及自动夹扣组件Sheet MetalFasteners工具套筒组件Socket Wrench Sets不锈钢链Stainless Steel Chains轭子T-Yoke轮胎链Tire Chains狗链Dog Chains喇叭头轭铁U-Yoke,T-Yoke For Speaker不锈钢输送带轮用轨道Stainless Wheel's Rack For Transporter工业用链Industrial Steel Link Chains拖链安全链Tow Chains And Safety Chains 机车离合器零件Manufacture Of Motorcycle's Cvt Parts牙条棒Thread Rod机(踏)车用螺丝、轴心Screws And Shafts For Motorcycle Or Bicycle针车用螺丝、轴心Screws And Shafts For Sewing Maching止付螺丝Socket Set Screws不锈钢宽牙螺丝Stainless Steel Coarse Thread Screws不锈钢高低牙螺丝Stainless Steel High-LowThread Screws不锈钢机械螺丝Stainless Steel Machine Screws不锈钢钻尾螺丝Stainless Steel Self Drilling Screws不锈钢自攻螺丝Stainless Steel Self Tapping Screws不锈钢自削螺丝Stainless Steel Thread Cutting Screws不锈钢三角牙螺丝Stainless Steel Tri-Lobular Thread Screws。
五金标准中英文对照表
94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125
DIN914 DIN915 DIN916 DIN917 DIN920 DIN921 DIN923 DIN927 DIN928 DIN929 DIN931 DIN933 DIN934 DIN934 DIN935 DIN936 DIN937 DIN938 DIN939 DIN940 DIN960 DIN961 DIN962 DIN963 DIN964 DIN965 DIN966 DIN970 DIN971 DIN972 DIN975 DIN976
30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61
DIN431 DIN432 DIN433 DIN434 DIN435 DIN436 DIN438 DIN439 DIN439 DIN440 DIN443 DIN444 DIN462 DIN463 DIN464 DIN465 DIN466 DIN467 DIN470 DIN471 DIN472 DIN478 DIN479 DIN480 DIN508 DIN525 DIN529 DIN546 DIN547 DIN551 DIN553 DIN555
pipe nuts with thread external tap washers for cheese head screws square taper washers for Usection square taper washers for Isections square washers slotted set with cup point hexagon thin nuts hexagon thin nuts rounds washers for wood constructions sealing caps,push-in type eye bolts form B internal tab washers washers with two taps knurled thumb screws with collar slotted knurled thumb screws with collar knurled thumb nuts with collar knurled thumb thin nuts sealing washers retaining rings for shafts(external),circlips retaining rings for bores(internal),circlips square head bolts with collar square head bolts with half dog point square head bolts with collar,half dog point and rounded end T-slot nuts single end studs masonry bolts slotted round nuts round nuts with drilled holes in one face slotted sit screws with flat point slotted set screws with cone point hexagon nuts ISO7436 ISO4035 ISO8675 ISO7094 ISO7092
螺钉英文描述
recessed ISO7050 GB846-85
普通六角螺帽 HEX NUTS
六角重型螺帽 HEAVY HEX NUTS
薄型螺帽 HEX JAM NUTS
焊接螺帽 WELD NUTS
高张力螺帽 HEIGH STRENGTH NUTS
建业用螺帽 STRUCTURAL NUTS
不锈钢螺帽 STAINLESS STEEL NUTS
铜螺帽 BRASS NUTS
197 DIN7984 薄型内六角圆柱头螺钉 hexagon socket head cap screws with，reduced
head
198 DIN7985 十字槽盘头螺钉 pan head screws with cross recessed ISO7045 GB818-85
206 DIN8140 螺纹护套（普通\自锁等） ciol inserts,coarse,fine thread,silf locking
Item DIN-Standard Description in Chinese Description in English ISO-Standard GB-Standard
不锈钢六角重型螺帽 STAINLESS STEEL HEAVY HEX NUTS
不锈钢六角螺帽 STAINLESS STEEL HEX NUTS
不锈钢尼龙嵌入螺帽 STAINLESS STEEL NYLON INSERT LOCK NUTS
尼龙嵌入防松螺帽 NYLON INSERT LOCK NUTS
螺栓_螺母英文简称
74 Legs Drywall Anchors 冲件 75 Hex Cap Nuts 六角盖头螺帽 76 Hex Serrated Nuts 六角锯齿螺帽 77 Hex Flange Nuts 六角轮缘螺帽 78 Hex Coupling Nuts(High Nuts) 高脚螺帽 78 Round Nuts 圆螺帽 79 Square Nuts 四角螺帽 80 Pipe Nuts 管用螺帽 81 Wheel Nuts 轮壳螺帽 82 Wing Nuts 蝶型螺帽 83U Nuts U 形螺帽 84 T Nuts T 形螺帽 85Eye Nuts 环首螺帽 86Kep Nuts 齿形螺帽 87 Clinch Nuts 齿花螺帽 88 Corten Steel Heavy Hex Nuts 耐候钢六角 重型螺帽 89 Weld Nuts 焊接螺帽 90 Heigh Strength Nuts 高张力螺帽 91 Structural Nuts 建业用螺帽 92 Stainless Steel Nuts 不锈钢螺帽 93 Brass Nuts 铜螺帽 94 Aluminum Nuts 铝螺帽 95 Alloy Steel Nuts 合金钢螺帽 96 Heavy Duty Wheel Hub Nuts 重型车螺帽 97 Acorn Cap Nuts 铁器焊接袋帽 98 All-Metal Prevailing Torque Type Nuts 金 属预置扭矩式螺帽 99 Anchor Nuts 壁虎螺帽 100 Big Size Nuts 大尺寸螺帽 101 Closed End Acorn Nuts 铁盖袋帽 102 Conical Washer Nuts 盘形华司螺帽 103 Din 986 Domed Cap Nuts 铁 盖 + 尼 龙 圈 组合盖帽 104 Flange Nylon Insert Lock Nuts 突缘尼龙 盖帽 105 Flat Waser Nuts 平面华司螺帽 106 Hex Slotted Nut 六角割沟螺帽 107 Self-Locking Nuts 自锁螺帽 108 Sliding Nuts 制止螺帽 109 Sln Self-Locking Nuts Sln-自动防松螺帽 110 Special Nuts 其它特殊螺帽 111Spring Nuts 弹簧螺帽 11230 Stainless Steel Flange Nuts 不 锈 钢 突
常用紧固件相关英语(中英对照).
螺纹大径:Major Diam中径:Pitch diam底径:Minor diam通止规:Go/No go gage机械性能:mechanical and physical propertiesunified thread 统一英制螺纹Lustrate hydrogen after galvanizing to avoid hydrogen embrittlement 镀后去氢,防止氢脆Case carburization 表面渗碳With across flats 对边With across corners 对角Radius of fillet:头下圆角Transition thread length 过度螺纹Wrenching height 扳拧高度Rockwell 铬氏硬度Vickers 维氏硬度Brinell 布氏硬度Metallography microscope 金相显微镜Salt spray device 盐雾试验箱Tensile testing machine 拉力试验机Cold forming 冷打Hot forging 红镦P C 8 = property class 8 机械性能8级原材料:Raw material球化退火:Annealing冷拔:Drawing冷镦:Forming机加工:Machining螺纹成型:Roll Threading热处理:heat-treatment表面处理:finish去氢:Lustrating hydrogen检验:Inspection包装:Packing入库:Stocking车床:lathe磨制:grinding红打:hot forging冲压:punching1 标准GB (国标DIN (德制JIS (日标ANSI (美标BA (英制2 螺纹M. MF (公制牙UNC.UNF (美制牙BSW.BSF (英制牙3 海关编码73181500 螺栓73181600 螺帽73182100 垫圈6-bobes recess 内梅花BO=black oxide 氧化发黑IHH=ind hex head 锯六角头PH=phillips 十字槽sw/fw=split washer/flatwasher 弹垫平垫kep nut 锁紧螺母cementation 渗碳acorn nut 盖形螺母螺丝头型Pan 圆头(盘头Oval 半沉头H.W.H.. 六角小法兰H.W.F. 六角大法兰CSK 沙拉头(沉头Large wafer 大扁平头Bugle 喇叭头Truss 盘头带垫Pozi 米制槽Phill 十字槽Serra-tion 垫下带花Flower Head 开花头欧洲标准EN国际标准化组织国际标准化组织标准ISO 国际电工委员会国际电工委员会标准IEC 国际国际电信联盟标准ITU欧共体欧洲电子元器件协会标准CECC德国德国标准DIN英国英国标准BS美国美国国家标准ANSI美国美国材料与试验协会标准ASTM美国美国机械工程师协会标准ASME美国美国电子工业协会标准EIA美国美国连接电子学工业协会标准IPC美国美国焊接协会标准AWS美国美国石油协会标准API美国美国国家公路与运输商协会标准AASHTO美国美国加热制冷与空调工程师协会标准ASHRAE 美国美国电气制造商协会标准NEMA美国美国给水工程协会标准AWWA美国美国仪器、系统与自动化协会标准ISA美国美国保险商实验室标准UL美国电气与电子工程师协会标准IEEE美国美国机动工程师协会标准SAE美国美国腐蚀工程师协会标准NACE美国美国纺织化学师与印染师协会标准AATCC美国美国钢结构油漆标准SSPC美国美国铝协会标准AA美国美国卫生工程协会标准ASSE美国美国煤气协会标准AGA美国美国阀门及配件工业协会标准MSS美国美国音频工程协会标准AES美国美国建筑小五金制造商协会标准BHMA 美国美国国家卫生基金会标准NSF美国美国标准NISO,PFI,RWMA美国美国信息与图像管理协会标准AIIM美国美国空调与制冷学会标准ARI美国美国军用标准MIL美国美国防火协会标准NFPA美国美国航空无线电设备标准ARINC美国美国齿轮协会标准AGMA加拿大加拿大标准协会标准CSA加拿大加拿大通用标准局标准CGSB澳大利亚澳大利亚国家标准AS德国德国工程师协会标准VDI欧共体欧洲电信标准ETSI法国法国标准NF日本日本工业标准JIS中国国家标准GB中国机械工业标准JB 中国电子工业标准SJ。
紧固件中英文对照大全
--------------------------------------------------------------------------------螺栓－－方头螺栓C级UDC 621.882.6 | GB 8-88 | 代替GB8-76Square head bolts-Product grade C－－沉头方颈螺栓UDC 621.882.6 | GB 10-88 | 代替GB10-76Flat countersunk square neck bolts－－沉头带榫螺拴UDC 621.882.6 | GB 11-88 | 代替GB11-76Flat countersunk nib bolts－－半圆头方颈螺栓UDC 621.882.6 | GB 12-88 | 代替GB12-76Cup head square neck bolts－－半圆头带榫螺栓UDC 621.882.6 | GB 13-88 | 代替GB13-76Cup head nid bolts－－大半圆头方颈螺栓C级ISO 8677:1986 | GB 14-1998 | 代替GB14-88Cup head square neck bolts with large head-Product grade C－－大半圆头带榫螺栓UDC 621.882.6 | GB 15-88 | 代替GB15-76Cup head nib bolts with large head－－六角头铰制孔用螺栓UDC 621.882.6 | GB 27-88 | 代替GB27-76Hexagon fit bolts-product grade A and B－－六角头螺杆带孔铰制孔用螺栓UDC 621.882.6 | GB 28-88 | 代替GB28-76Hexagon fit bolts with split pin hole on shank-product grade A and B－－六角头头部带槽螺栓A 和B 级UDC 621.882.6 | GB 29.1-88 | 代替GB29-76 Hexagon bolts with slot on head -product A and B－－十字槽凹穴六角头螺栓UDC 621.882.6 | GB 29.2-88 | 代替GB29-76Cross recessed hexagon bolts with indentation－－六角头螺杆带孔螺栓UDC 621.882.6 | GB 31.1-88 | 代替GB31、23、24-76 Hexagon bolts with split pin hole on shank-product grade A and B－－六角头螺杆带孔螺栓细杆B级UDC 621.882.6 | GB 31.2-88 | 代替GB31、23、24-76 Hexagon bolts with split pin hole on shank-Reduced shank-product grade B－－六角头螺杆带孔螺栓细牙A和B级UDC 621.882.6 | GB 31.3-88 | 代替GB31、23、24-76Hexagon bolts with split pin hole on shank-Fine pitch thread-product grade A and B－－六角头头部带孔螺栓A 和B级UDC 621.882.6 | GB 32.1-88 | 代替GB32、25、26-76 Hexagon bolts with wire holes on head-product grade A and B－－六角头头部带孔螺栓细杆B级UDC 621.882.6 | GB 32.2-88 | 代替GB32、25、26-76 Hexagon bolts with wire holes on head-Reduced shank-product grade B－－六角头头部带孔螺栓细牙A 和 B 级UDC 621.882.6 | GB 32.3-88 | 代替GB32、25、26-76Hexagon bolts with wire holes on head-Fine pitch thread-product grade A and B－－下方头螺栓B级UDC 621.882.6 | GB 35-88 | 代替GB35-76Square head bolts with small head-praduct grade B－－T 形槽用螺栓UDC 621.882.6 | GB 37-88 | 代替GB37-76Bolts for T-Slot－－加强半圆头方颈螺栓GB /T794-93 | 代替GB794-67Strengthened cup head square neck bolts－－活节螺栓UDC 621.882.6 | GB 798-88 | 代替GB798-76Eye bolts－－地脚螺栓UDC 621.882.6 | GB 799-88 | 代替GB799-76Eyelet bolts－－沉头双榫螺UDC 621.882.6 | GB 800-88 | 代替GB800-77Flat countersunk double nib bolts－－小圆半头低方颈螺栓B级ISO 8678:1988 | GB /T 801-1998 | 代替GB801-88Cup head square neck bolts with small head and short neck-product grade B－－六角头螺栓C级ISO 4016:1999 | GB /T 5780-2000 | 代替GB/T 5780-1986 Hexagon head bolts-product grade C－－六角头螺栓全螺纹C级ISO 4018:1999 | GB /T 5781-2000 | 代替GB/T 5781-1986 Hexagon head bolts-Full thread-product grade C－－六角头螺栓ISO 4014：1999 | GB /T 5782-2000 | 代替GB/T 5782-1986Hexagon head bolts－－六角头螺栓全螺纹ISO 4017：1999 | GB /T 5783-2000 | 代替GB/T 5783-1986 Hexagon head bolts-Full thread－－六角头螺栓-细杆-B级UDC 621.882.6 | GB 5784-86 | 代替GB30、21-76Hexagon head bolts-Reduced shank -Product grade B－－六角头螺栓细牙ISO 8765：1999 | GB /T 5785-2000 | 代替GB/T 5785-1986 Hexagon head bolts with fine pitch thread－－六角头螺栓细牙全螺纹ISO 8676：1999 | GB /T 5786-2000 | 代替GB/T 5786-1986 Hexagon head bolts with fine pitch thread-Full thread－－六角法兰面螺栓-加大系列-B级UDC 621.882.6 | GB 5789-86 |Hexagon flange bolts-Heavy series-product grade B－－六角法兰面螺栓-加大系列-细杆-B级UDC 621.882.6 | GB 5790-86 |Hexagon flange bolts-Heavy series-product grade B－－六角法兰面螺栓小系列ISO 4162：1990 | GB /T 16674-1996 | 代替GB/T 5787、5788-1986Hexagon flange bolts-Small series－－钢网架螺栓球节点用高强度螺栓GB /T 16939-1997 |High strength bolts for joints of space grid structures螺柱－－双头螺柱bm=1d UDC 621.882 | GB 897-88 | 代替GB897-76Double end studs-bm=1d－－双头螺柱bm=1.25d UDC 621.882 | GB 898-88 | 代替GB898-76Double end studs-bm=1.25d－－双头螺柱bm=1.5d UDC 621.882 | GB 899-88 | 代替GB899-76Double end studs-bm=1.5d－－双头螺柱bm=2d UDC 621.882 | GB 900-88 | 代替GB900-76Double end studs--bm=2d－－等长双头螺柱B级UDC 621.882 | GB 901-88 | 代替GB901-76Double end studs(clamping type) -Product grade B－－手工焊用焊接螺柱GB 902.1-89 | 代替GB902-76Weld studs for manual welding－－机动弧焊用焊接螺柱GB 902.2-89 | 代替GB902-76Weld studs for arc welding－－储能焊用焊接螺柱GB 902.3-89 | 代替GB902-76Weld studs for capacitor discharge welding－－等长双头螺柱C级UDC 621.882 | GB 953-88 | 代替GB953-76 Double end studs(clamping type)-product grade C－－螺杆GB /T 15389-94 |Threaded rods螺母－－方螺母C级UDC 621.882.3 | GB 39-88 | 代替GB39-76 Square nuts-product grade C－－六角螺母C级ISO 4034：1999 | GB /T41-2000 | 代替GB/T 41-1986 Hexagon nuts-product grade C－－六角厚螺母ISO 621.882.3 | GB 56-88 | 代替GB56-76Hexagon thick nuts－－蝶形螺母UDC 621.882.3 | GB 62-88 | 代替GB62-76Wing nuts－－环形螺母UDC 621.882.3 | GB 63-88 | 代替GB63-76Lifting nuts－－组合式盖形螺母UDC 621.882.3 | GB 802-88 | 代替GB802-76 Acorn nuts－－球面六角螺母UDC 621.882.3 | GB 804-88 | 代替GB804-76 Hexagon nuts with raised face－－扣紧螺母UDC 621.882.3 | GB 805-88 | 代替GB805-76Tight nuts－－滚花高螺母UDC 621.882.3 | GB 806-88 | 代替GB806-76Knurled nut with collar－－滚花薄螺母UDC 621.882.3 | GB 807-88 | 代替GB807-76Knurled nuts－－小六角特扁细牙螺母UDC 621.882.3 | GB 808-88 | 代替GB808-76 Small hexagon thin nuts-Fine pitch thread－－嵌装圆螺母UDC 621.882.3 | GB 809-88 | 代替GB809-76Lnsert round nuts－－小圆螺母UDC 621.882.3 | GB 810-88 | 代替GB810-76Small round nuts－－圆螺母UDC 621.882.3 | GB 812-88 | 代替GB812-76Round nuts－－端面带孔圆螺母UDC 621.882.3 | GB 815-88 | 代替GB815-76 Round nuts with drilled holes in one face－－侧面带孔圆螺母UDC 621.882.3 | GB 816-88 | 代替GB816-79Round nuts with set pin holes in side－－带槽圆螺母UDC 621.882.3 | GB 817-88 | 代替GB817-76Slotted round nuts－－1型非金属嵌件六角锁紧螺母ISO 7040：1997 | GB /T 889.1-2000 | 代替GB/T 889-1986Prevailing torque type hexagon nuts(with non-metallic insert),style 1－－1型非金属嵌件六角锁紧螺母细牙ISO 10512：1997 | GB /T 889.2-2000 |Prevailing torque type hexagon nuts(with non-metallic insert),style 1,with fine pitch thread－－盖形螺母UDC 621.882.3 | GB 923-88 | 代替GB923-76Acorn nuts－－1型六角螺母ISO 4032：1999 | GB /T 6170-2000 | 代替GB/T 6170-1986Hexagon nuts,style 1－－1型六角螺母细牙ISO 8673：1999 | GB /T 6171-2000 | 代替GB/T 6171-1986 Hexagon nuts,style 1,with fine pitch thread－－六角薄螺母ISO 4035：1999 | GB /T 6172.1-2000 | 代替GB/T 6172-1986Hexagon thin nuts(chamfered)－－非金属嵌件六角锁紧薄螺母ISO 10511：1997 | GB /T 6072.2-2000 |Prevailing torque type hexagon thin nuts(with non-metallic insert)－－六角薄螺母细牙ISO 8675：1999 | GB /T 6173-2000 | 代替GB/T 6173-1986 Hexagon thin nuts(chamfered) with fine pitch thread－－六角薄螺母无倒角ISO 4036：1999 | GB /T 6174-2000 | 代替GB/T 6174-1986 Hexagon thin nuts(unchamfered)－－2型六角螺母ISO 4033：1999 | GB /T 6175-2000 | 代替GB/T 6175-1986Hexagon nuts,style 2－－2型六角螺母细牙ISO 8674：1999 | GB /T 6176-2000 | 代替GB/T 6176-1986 Hexagon nuts,style 2,with fine pitch thread－－六角法兰面螺母ISO 4161：1999 | GB /T 6177.1-2000 | 代替GB/T 6177-1986 Hexagon nuts with flange－－六角法兰面螺母细牙ISO 10663：1999 | GB /T 6177.2-2000 |Hexagon nuts with flange-fine pitch thread－－1型六角开槽螺母-A和B级UDC 621.882.3 | GB 6178-86 | 代替GB57~58-76 Hexagon slotted and castle nuts,style 1 -product grades A and B－－1型六角开槽螺母-C级UDC 621.882.3 | GB 6179-86 | 代替GB57~58-76Hexagon slotted nuts,style 1 -product grade C－－2型六角开槽螺母-A和B级UDC 621.882.3 | GB 6180-86 |Hexagon slotted and castle nuts,style 2 -Product grades A and B－－六角开槽薄螺母-A和B级UDC 621.882.3 | GB 6181-86 | 代替GB59~60-76 Hexagon thin slotted nuts-Product grades A and B－－2型非金属嵌件六角锁紧螺母ISO 7041：1997 | GB /T 6182-2000 | 代替GB/T 6182-1986Prevailing torque type hexagon nuts(with non-metallic insert),style 2－－非金属嵌件六角法兰面锁紧螺母ISO 7043：1997 | GB /T 6183.1-2000 | 代替GB/T 6183-1986Prevailing torque type hexagon nuts with flange(with non-metallic insert)－－非金属嵌件六角法兰面锁紧螺母细牙ISO 12125：1997 | GB /T 6183.2-2000 | Prevailing torque type hexagon nuts with flange(with non-metallic insert)with fine pitch thread－－1型全金属六角锁紧螺母ISO 7719：1997 | GB /T 6184-2000 | 代替GB/T 6184-1986 Prevailing torque type all-metal hexagon nuts,style 1－－2型全金属六角锁紧螺母ISO 7042：1997 | GB /T 6185.1-2000 | 代替GB/T 6185-1986 Prevailing torque type all-metal hexagon nuts,style 2－－2型全金属六角锁紧螺母细牙ISO 10513：1997 | GB /T 6185.2-2000 |Prevailing torque type all-metal hexagon nuts,style 2,with fine pitch thread－－2型全金属六角锁紧螺母9级ISO 7720：1997 | GB /T 6186-2000 | 代替GB/T 6186-1986Prevailing torque type all-metal hexagon nuts,style 2-Property class 9－－全金属六角法兰面锁紧螺母ISO 7044：1997 | GB /T 6187.1-2000 | 代替GB/T 6187-1986Prevailing torque type all-metal hexagon nuts with flange－－全金属六角法兰面锁紧螺母细牙ISO 12126：1997 | GB /T 6187.2-2000 |Prevailing torque type all-metal hexagon nuts with flange with fine pitch thread－－1型六角开槽螺母细牙A和B级UDC 621.882.3 | GB 9457-88 | 代替GB57、58-76 Hexagon slotted and castle nuts,style 1-fine pitch thread-product grades A and B－－2型六角开槽螺母细牙A和B级UDC 621.882.3 | GB 9458-88 |Hexagon slotted and castle nuts,style 2--Fine pitch thread -Product grades A and B－－六角开槽薄螺母细牙A和B级UDC 621.882.3 | GB 9459-88 | 代替GB59、60-76 Hexagon thin slotted nuts--Fine pitch thread -Product grades A and B－－焊接方螺母GB /T 13680-92 |Square weld nuts－－焊接六角螺母GB /T 13681-92 |Hexagon weld nuts－－平头铆螺母GB /T 17880.1-1999 |Flat head riveted nuts－－沉头铆螺母GB /T 17880.2-1999 |Countersunk head riveted nuts－－小沉头铆螺母GB /T 17880.3-1999 |Small countersunk head riveted nuts－－120°小沉头铆螺母GB /T 17880.4-1999 |120°Small countersunk head riveted nuts－－平头六角铆螺母GB /T 17880.5-1999 |Flat head hexagon riveted nuts－－精密机械用六角螺母ISO 4166：1979 | GB /T 18195-2000 |Hexagon nuts for fine mechanics螺钉－－开槽圆柱头螺钉ISO 1207：1992 | GB /T 65-2000 | 代替GB/T 65-1985 Slotted cheese head screws－－开槽盘头螺钉ISO 1580：1994 | GB /T 67-2000 | 代替GB/T 67-1985Slotted pan head screws－－开槽沉头螺钉ISO 2009：1994 | GB /T 68-2000 | 代替GB/T 68-1985Slotted countersunk flat head screws (common head style)－－开槽半沉头螺钉ISO 2010：1994 | GB /T 69-2000 | 代替GB/T 69-1985 Countersunk slotted raised head screws (common head style)－－内六角圆柱头螺钉ISO 4762：1997 | GB /T 70.1-2000 | 代替GB/T 70-1985 Hexagon socket head cap screws－－内六角平圆头螺钉ISO 7380：1997 | GB /T 70.2-2000 |Hexagon socket button head screws－－内六角沉头螺钉ISO 10642：1997 | GB /T 70.3-2000 |Hexagon socket countersunk head screws－－开槽锥端紧定螺钉UDC 621.882.219 | GB 71-85 | 代替GB71-76Slotted set screws with cone point－－开槽锥端定位螺钉UDC 621.882.2 | GB 72-88 | 代替GB72-76Slotted setscrews with cone point－－开槽平端紧定螺钉UDC 621.882.219.4 | GB 73-85 | 代替GB73-76Slotted set screws with flat point－－开槽凹端紧定螺钉UDC 621.882.219.4.092.6 | GB 74-85 | 代替GB74-76Slotted set screws with cup point－－开槽长圆柱端紧定螺钉UDC 621.882.219.4.092.5 | GB 75-85 | 代替GB75-76Slotted set screws with long dog point－－内六角平端紧定螺钉ISO 4026：1993 | GB /T 77-2000 | 代替GB/T 77-1985 Hexagon socket set screws with flat point－－内六角锥端紧定螺钉ISO 4027：1993 | GB /T 78-2000 | 代替GB/T 78-1985 Hexagon socket set screws with cone point－－内六角圆柱端紧定螺钉ISO 4028：1993 | GB /T 79-2000 | 代替GB/T 79-1985 Hexagon socket set screws with dog point－－内六角凹端紧定螺钉ISO 4029：1993 | GB /T 80-2000 | 代替GB/T 80-1985 Hexagon socket set screws with cup point－－方头长圆柱球面端紧定螺钉UDC 621.882.2 | GB 83-88 | 代替GB83-76Square set screws with long dog point and rounded end－－方头凹端紧定螺钉UDC 621.882.2 | GB 84-88 | 代替GB84-76Square set screws with cup point－－方头长圆柱端紧定螺钉UDC 621.882.2 | GB 85-88 | 代替GB85-76Square set screws with long dog point－－方头短圆柱锥端紧定螺钉UDC 621.882.2 | GB 86-88 | 代替GB86-76Square set screws with short dog point and cone end－－十字槽盘头螺钉ISO 7045：1994 | GB /T 818-2000 | 代替GB/T 818-1985Pan head screws with cross recess－－十字槽沉头螺钉第1部分：钢4.8级ISO 7046-1：1994 | GB /T 819.1-2000 | 代替GB/T 819-1985Countersunk flat head screws (common head style)with cross recess-Part 1:Steel of property class 4.8－－十字槽沉头螺钉第2部分：钢8.8、不锈钢A2-70和有色金属CU2或CU3ISO 7046-2：1990 | GB /T 819.2-1997 |Cross recessed countersunk flat head screws (common head style)-Grade A-Part 2:Steel of property class 8.8, stainless and non-ferrous metals－－十字槽半沉头螺钉ISO 7047：1994 | GB /T 820-2000 | 代替GB/T 820-1985 Countersunk raised head screws (common head style) with cross recess－－方头平端紧定螺钉UDC 621.882.2 | GB 821-88 | 代替GB821-76Square set screws with chamfered end－－十字槽圆柱头螺钉ISO 7048：1998 | GB /T 822-2000 | 代替GB/T 822-1988Cheese head screws with cross recess－－十字槽小盘头螺钉UDC 621.882.2 | GB 823-88 | 代替GB823-76Cross recessed small pan head screws－－吊环螺钉UDC 621.882 | GB 825-88 | 代替GB825-76Eyebolts－－开槽盘头定位螺钉UDC 621.882.2 | GB 828-88 | 代替GB828-76Slotted pan head set setscrews with dog point－－开槽圆柱端定位螺钉UDC 621.882.2 | GB 829-88 | 代替GB829-76Slotted setscrews with dog point－－开槽圆柱头轴位螺钉UDC 621.882.2 | GB 830-88 | 代替GB830-76Slotted cheese head screws with shoulder－－开槽无头轴位螺钉UDC 621.882.2 | GB 831-88 | 代替GB831-76Slotted shoulder screws－－开槽带孔球面圆柱头螺钉UDC 621.882.2 | GB 832-88 | 代替GB832-76Slotted capstan screws－－开槽大圆柱头螺钉UDC 621.882.2 | GB 833-88 | 代替GB833-76Slotted large cheese head screws－－滚花高头螺钉UDC 621.882.2 | GB 834-88 | 代替GB834-76Knurled thumb screws－－滚花平头螺钉UDC 621.882.2 | GB 835-88 | 代替GB835-76Knurled screws－－滚花小头螺钉UDC 621.882.2 | GB 836-88 | 代替GB836-76Knurled screws with small head－－开槽盘头不脱出螺钉UDC 621.882.2 | GB 837-88 | 代替GB837-76Slotted pan head screws with waisted shank－－六角头不脱出螺钉UDC 621.882.2 | GB 838-88 | 代替GB838-76Hexagon screws with waisted shank－－滚花头不脱出螺钉UDC 621.882.2 | GB 839-88 | 代替GB839-76Knurled thumb screws with waisted shank－－塑料滚花头螺钉UDC 621.882.2 | GB 840-88 | 代替GB840-79Plastic diamond knurlhead screws－－开槽球面圆柱头轴位螺钉UDC 621.882.2 | GB 946-88 | 代替GB946-76Slotted raised head with shoulder－－开槽球面大圆柱头螺钉UDC 621.882.2 | GB 947-88 | 代替GB947-76Slotted large raised cheese head screws－－开槽沉头不脱出螺钉UDC 621.882.2 | GB 948-88 | 代替GB948-76Slotted countersunk head screws with waisted shank－－开槽半沉头不脱出螺钉UDC 621.882.2 | GB 949-88 | 代替GB949-76Slotted raised countersunk head screws with waisted shank－－内六角花形盘头螺钉UDC 621.882.2 | GB 2672-86 | 代替GB2672-81Hexagon lobular socket pan head screws－－内六角花形沉头螺钉UDC 621.882.2 | GB 2673-86 | 代替GB2673-81Hexagon lobular socket countersunk head screws－－内六角花形半沉头螺钉UDC 621.882.2 | GB 2674-86 | 代替GB2674-81Hexagon lobular socket raised countersunk head screws－－内六角圆柱头轴肩螺钉UDC 621.882.215.6 | GB 5281-85 |Hexagon socket head shoulder screws－－内六角花形圆柱头螺钉-4.8级UDC 621.882.2 | GB 6190-86 | 代替GB2671-81 Hexagon lobular socket head cap screws-property class 4.8－－内六角花形圆柱头螺钉-8.8和10.9级UDC 621.882.2 | GB 6191-86 | 代替GB2671-81 Hexagon lobular socket head cap screws-property class 8.8 and 10.9－－精密机械用紧固件十字槽螺钉GB /T 13806.1-92 |Fasteners for mechanics-Cross recessed screws垫圈－－标准型弹簧垫圈UDC 621.882.4 | GB 93-87 | 代替GB93-76Single coil spring lock washers Normal type－－平垫圈C级ISO 7091：2000 | GB /T 95-2002 | 代替GB/T 95-1985Plain washers-Product grade C－－大垫圈A级ISO 7093-1：2000 | GB /T 96.1-2002 | 代替GB/T 96-1985Plain washers-Large series-Product grade A－－大垫圈C级ISO 7093-2：2000 | GB /T 96.2-2002 | 代替GB/T 96-1985Plain washers-Large series-Product grade C－－平垫圈A级ISO 7089：2000 | GB /T 97.1-2002 | 代替GB/T 97.1-1985Plain washers-Product grade A－－平垫圈倒角型A级ISO 7090：2000 | GB /T 97.2-2002 | 代替GB/T 97.2-1985Plain washers,chamfered-Product grade A－－销轴用平垫圈ISO 8738：1986 | GB /T 97.3-2000 |Plain washers for clevis pins－－平垫圈用于螺钉和垫圈组合件ISO 10673：1998 | GB /T 97.4-2002 | 代替GB/T 9074.24、9074.25-1988Plain washers for screw and washer assemblies－－平垫圈用于自攻螺钉和垫圈组合件ISO 10669：1999 | GB /T 97.5-2002 | 代替GB/T 9074.29、9074.30-1988Plain washers for tapping screw and washer assemblies－－小垫圈A级ISO 7092：2000 | GB /T 848-2002 | 代替GB/T 848-1985Plain washers-small series-Product grade A－－球面垫圈UDC 621.882.4 | GB 849-88 | 代替GB849-76Washers with ball face－－锥面垫圈UDC 621.882.4 | GB 850-88 | 代替GB850-76Washers with cone face－－开口垫圈UDC 621.882.4 | GB 851-88 | 代替GB851-76Washers with split－－工字钢用方斜垫圈UDC 621.882.4 | GB 852-88 | 代替GB852-76Square taper washers for I section－－槽钢用方斜垫圈UDC 621.882.4 | GB 853-88 | 代替GB853-76Square taper washers for slot section－－单耳止动垫圈UDC 621.882.4 | GB 854-88 | 代替GB854-76Tab washers with long tab－－双耳止动垫圈UDC 621.882.4 | GB 855-88 | 代替GB855-76Tab washers with long tab and wing－－外舌止动垫圈UDC 621.882.4 | GB 856-88 | 代替GB856-76External tab washers－－圆螺母用止动垫圈UDC 621.882.4 | GB 858-88 | 代替GB858-76Tab washers for round nut－－轻型弹簧垫圈UDC 621.882.4 | GB 859-87 | 代替GB859-76Single coil spring lock washers,Light type－－鞍形弹性垫圈UDC 621.882.4 | GB 860-87 | 代替GB860-76Curved spring washers－－内齿锁紧垫圈UDC 621.882.4 | GB 861.1-87 | 代替GB861-76Lock washers internal teeth－－内锯齿锁紧垫圈UDC 621.882.4 | GB 861.2-87 |Serrated lock washers internal teeth－－外齿锁紧垫圈UDC 621.882.4 | GB 862.1-87 | 代替GB862-76Lock washers external teeth－－外锯齿锁紧垫圈UDC 621.882.4 | GB 862.2-87 |Serrated lock washers external teeth－－波形弹性垫圈UDC 621.882.4 | GB 955-87 | 代替GB955-76Wave spring washers－－锥形锁紧垫圈UDC 621.882.4 | GB 956.1-87 | 代替GB956-76 Countersunk external toothed lock washers－－锥形锯齿锁紧垫圈UDC 621.882.4 | GB 956.2-87 |Countersunk Serrated external toothed lock washers－－特大垫圈C级ISO 7094：2000 | GB /T 5287-2002 | 代替GB/T 5287-1985 Plain washers-Extra large series-Product grade C－－重型弹簧垫圈UDC 621.882.4 | GB 7244-87 |Single coil spring lock washers,heavy type－－鞍形弹簧垫圈UDC 621.882.4 | GB 7245-87 |Curved Single coil spring lock washers－－波形弹簧垫圈UDC 621.882.4 | GB 7246-87 |Wave Single coil spring lock washers木螺钉－－开槽圆头木螺钉UDC 621.882.2 | GB 99-86 | 代替GB99-76Slotted round head wood screws－－开槽沉头木螺钉UDC 621.882.2 | GB 100-86 | 代替GB100-76Slotted countersunk head wood screws－－开槽半沉头木螺钉UDC 621.882.2 | GB 101-86 | 代替GB101-76Slotted raised countersunk head wood screws－－六角头木螺钉UDC 621.882.2 | GB 102-86 | 代替GB102-76Hexagon head wood screws－－十字槽圆头木螺钉UDC 621.882.2 | GB 950-86 | 代替GB950-76Cross recessed round head wood screws－－十字槽沉头木螺钉UDC 621.882.2 | GB 951-86 | 代替GB951-76Cross recessed countersunk head wood screws－－十字槽半沉头木螺钉UDC 621.882.2 | GB 952-86 | 代替GB952-76Cross recessed raised head countersunk head wood screws自攻螺钉－－十字槽盘头自攻螺钉UDC 621.882.216.5.082.8 | GB 845-85 | 代替GB845-76 Cross recessed pan head tapping screws－－十字槽沉头自攻螺钉UDC 621.882.216.5.082.8 | GB 846-85 | 代替GB846-76 Cross recessed countersunk head tapping screws－－十字槽半沉头自攻螺钉UDC 621.882.216.5.082.8 | GB 847-85 | 代替GB847-76 Cross recessed raised countersunk head tapping screws－－开槽盘头自攻螺钉UDC 621.882.215.082.8 | GB 5282-85 |Slotted pan head tapping screws－－开槽沉头自攻螺钉UDC 621.882.215.082.8 | GB 5283-85 |Slotted countersunkhead tapping screws－－开槽半沉头自攻螺钉UDC 621.882.215.082.8 | GB 5284-85 |Slotted raised countersunkhead tapping screws－－六角头自攻螺钉UDC 621.882.215.082.8 | GB 5285-85 |Hexagon head tapping screws－－十字槽盘头自攻锁紧螺钉UDC 621.882 | GB 6560-86 |Cross recessed pan head thread forming screws－－十字槽沉头自攻锁紧螺钉UDC 621.882 | GB 6561-86 |Cross recessed countersunk head thread forming screws－－十字槽半沉头自攻锁紧螺钉UDC 621.882 | GB 6562-86 |Cross recessed raised countersunk head thread forming screws－－六角头自攻锁紧螺钉UDC 621.882 | GB 6563-86 |Hexagon head thread forming screws－－内六角花形圆柱头自攻锁紧螺钉UDC 621.882 | GB 6564-86 |Hexagon lobular socket thread forming screws－－十字槽头凹穴六角头自攻螺钉UDC 621.882.2 | GB 9456-88 |Cross recessed hexagon head tapping screws with indentation－－精密机械用紧固件十字槽自攻螺钉刮削端GB /T 13806.2-92 |Fasteners for fine mechanics-Cross recessed tapping screws-Scrape point－－墙板自攻螺钉GB /T 14210-93 |Dry wall screws－－十字槽盘头自钻自攻螺钉ISO 15481:1999 | GB /T 15856.1-2002 | 代替GB/T 15856.1-1995Cross recessed pan head drilling screws with tapping screw thread－－十字槽沉头自钻自攻螺钉ISO 15482:1999 | GB /T 15856.2-2002 | 代替GB/T 15856.2-1995Cross recessed countersunk head drilling screws with tapping screw thread－－十字槽半沉头自钻自攻螺钉ISO 15483:1999 | GB /T 15856.3-2002 | 代替GB/T 15856.3-1995Cross recessed raised countersunk head drilling screws with tapping screw thread－－六角法兰面自钻自攻螺钉GB /T 15856.4-2002 | 代替GB/T 15856.4-1995Hexagon flange drilling screws with tapping screw thread－－六角凸缘自钻自攻螺钉ISO 15480:1999 | GB /T 15856.5-2002 |Hexagon washer head drilling screws with tapping screw thread－－六角凸缘自攻螺钉ISO 7053:1992 | GB /T 16824.1-1997 |Hexzgon head tapping screws with collar－－六角法兰面自攻螺钉ISO 10509:1992 | GB /T 16824.2-1997 |Hexagon flange head tapping screws销－－开口销ISO 1234:1997 | GB /T 91-2000 | 代替GB/T 91-1986Split pins－－圆锥销ISO 2339:1986 | GB /T 117-2000 | 代替GB/T 117-1996Taper pins－－内螺纹圆锥销ISO 8736:1986 | GB /T 118-2000 | 代替GB?T 118-1996Taper pins with internal thread－－圆柱销不淬硬钢和奥氏体不锈钢ISO 2338:1997 | GB /T 119.1-2000 | 代替GB/T 119-1986Parallel pins,of unhardened steel and austenitic stainless steel－－圆柱销淬硬钢和马氏体不锈钢ISO 8734:1997 | GB /T 119.2-2000 | 代替GB/T 119-1986Parallel pins,of hardened steel and martensitic stainless steel (Dowel pins)－－内螺纹圆柱销不淬硬钢和奥氏体不锈钢ISO 8733:1997 | GB /T 120.1-2000 | 代替GB/T 120-1986Parallel pins with internal thread, of unhardened steel and austenitic stainless steel－－内螺纹圆柱销淬硬钢和马氏体不锈钢ISO 8735:1997 | GB /T 120.2-2000 | 代替GB/T 120-1986Parallel pins with internal thread,of hardened steel and martensitic stainless steel－－开尾圆锥销UDC 621.886 | GB 877-76 | 代替GB877-76Taper pins with split－－螺纹圆柱销UDC 621.886 | GB 878-86 | 代替GB878-76Parallel pins with external thread－－弹性圆柱销直槽重型ISO 8752:1997 | GB /T 879.1-2000 | 代替GB/T 879-1986 Spring-type straight pins-Slotted, heavy duty－－弹性圆柱销直槽轻型ISO 13337:1997 | GB /T 879.2-2000 |Spring-type straight pins-Slotted,light duty－－弹性圆柱销卷制重型ISO 8748:1997 | GB /T 879.3-2000 |Spring-type straight pins-Coiled,heavy duty－－弹性圆柱销卷制标准型ISO 8750:1997 | GB /T 879.4-2000 |Spring-type straight pins-Coiled,standard duty－－弹性圆柱销卷制轻型ISO 8751:1997 | GB /T 879.5-2000 |Spring-type straight pins-Coiled,light duty－－带孔销UDC 621.886 | GB 880-86 | 代替GB880-76Pins with split pin hole－－螺尾锥销ISO 8737:1986 | GB /T 881-2000 | 代替GB/T 881-1986Taper pins with external thread－－销轴UDC 621.886 | GB 882-86 | 代替GB882-76Clevis pins with head－－槽销平行沟槽GB /T 13829.1-92 |Crooved pins-Parallel grooved－－槽销锥销GB /T 13829.2-92 |Crooved pins-taper grooved－－槽销圆头沉头GB /T 13829.3-92 |Grooved pins-with round head or countersunk head铆钉－－平头铆钉UDC 621.884 | GB 109-86 | 代替GB109-76Flat head rivets－－标牌铆钉UDC 621.884 | GB 827-86 | 代替GB827-76Rivets for name plate－－半圆头铆钉(粗制)UDC 621.884 | GB 863.1-86 | 代替GB863-76Round head rivets-Black－－小半圆头铆钉(粗制)UDC 621.884 | GB 863.2-86 |Round head rivets with small head-Black－－平锥头铆钉(粗制)UDC 621.884 | GB 864-86 | 代替GB864-76Cone head rivets-Black－－沉头铆钉(粗制)UDC 621.884 | GB 865-86 | 代替GB865-86Countersunk head rivets-Black－－半沉头铆钉(粗制)UDC 621.884 | GB 866-86 | 代替GB866-76Oval countersunk head rivets-Black－－半圆头铆钉UDC 621.884 | GB 867-86 | 代替GB867-76Round head rivets－－平锥头铆钉UDC 621.884 | GB 868-86 | 代替GB868-76Cone head rivets－－沉头铆钉UDC 621.884 | GB 869-86 | 代替GB869-76 Countersunk head rivets－－半沉头铆钉UDC 621.884 | GB 870-86 | 代替GB870-76Oval countersunk head rivets－－扁圆头铆钉UDC 621.884 | GB 871-86 | 代替GB871-76Flat round head rivets－－扁平头铆钉UDC 621.884 | GB 872-86 | 代替GB872-76Thin head rivets－－扁圆头半空心铆钉UDC 621.884 | GB 873-86 | 代替GB873-76 Oval head semi-tubular rivets－－120°沉头半空心铆钉UDC 621.884 | GB 874-86 | 代替GB874-76 120 degree countersunk head semi-tubular rivets－－扁平头半空心铆钉UDC 621.884 | GB 875-86 | 代替GB875-76 Thin head semi-tubular rivets－－空心铆钉UDC 621.884 | GB 876-86 | 代替GB876-76Tubular rivets－－120°沉头铆钉UDC 621.884 | GB 954-86 | 代替GB954-76120 degree countersunk head rivets－－管状铆钉UDC 621.884 | GB 975-86 | 代替GB975-76Pipe type rivets－－大扁圆头铆钉UDC 621.884 | GB 1011-86 | 代替GB1011-76 Truss head rivets－－120°半沉头铆钉UDC 621.884 | GB 1012-86 | 代替GB1012-76 120 degree oval countersunk rivets－－平锥头半空心铆钉UDC 621.884 | GB 1013-86 | 代替GB1013-76 Cone head semi-tubler rivets－－大扁圆头半空心铆钉UDC 621.884 | GB 1014-86 | 代替GB1014-76 Truss head semi-tublar rivets－－沉头半空心铆钉UDC 621.884 | GB 1015-86 | 代替GB1015-76 Countersunk head semi-tublar rivets－－无头铆钉UDC 621.884 | GB 1016-86 | 代替GB1016-76 Headless rivets－－封闭型扁圆头抽芯铆钉GB 12615-90 |Mushroom head break mandrel closed end blind rivets－－封闭型沉头抽芯铆钉GB 12616-90 |120 deg flush head break mandrel closed end blind rivets－－开口型沉头抽芯铆钉GB 12617-90 |120 deg flush head break mandrel blind rivets－－开口型扁圆头抽芯铆钉GB 12618-90 |Mushroom head break mandrel blind rivets－－扁圆头击芯铆钉GB /T 15855.1-1995 |Flat round head drive rivets－－沉头击芯铆钉GB /T 15855.2-1995 |Countersunk head drive rivets挡圈－－锥销锁紧挡圈UDC 621.885 | GB 883-86 | 代替GB883-76Lock rings with cone pin－－螺钉锁紧挡圈UDC 621.885 | GB 884-86 | 代替GB884-76Lock ring with screw－－带锁圈的螺钉锁紧挡圈UDC 621.885 | GB 885-86 | 代替GB885-76 Lock rings with screw and circlip－－轴肩挡圈UDC 621.885 | GB 886-86 | 代替GB886-76Rings for shoulder－－螺钉紧固轴端挡圈UDC 621.885 | GB 891-86 | 代替GB891-76Lock rings at the end of shaft with screw－－螺栓紧固轴端挡圈UDC 621.885 | GB 892-86 | 代替GB892-76Lock rings at the end of shaft with bolt－－孔用弹性挡圈-A型UDC 621.885 | GB 893.1-86 | 代替GB893-76 Circlips for holes-type A－－孔用弹性挡圈-B型UDC 621.885 | GB 893.2-86 |Circlips for hole-type B－－轴用弹性挡圈-A型UDC 621.885 | GB 894.1-86 | 代替GB894-76 Circlips for shaft-type A－－轴用弹性挡圈-B型UDC 621.885 | GB 894.2-86 |Circlips for shaft-type B－－孔用钢丝挡圈UDC 621.885 | GB 895.1-86 | 代替GB895-76 Roundwire snap rings for hole－－轴用钢丝挡圈UDC 621.885 | GB 895.2-86 | 代替GB895-76 Roundwire snap rings for shaft－－开口挡圈UDC 621.885 | GB 896-86 | 代替GB896-76“E”rings－－钢丝锁圈UDC 621.885 | GB 921-86 | 代替GB921-76Round wire circlips－－夹紧挡圈UDC 621.885 | GB 960-86 | 代替GB960-76Grip rings紧固件-组合件和连接副－－钢结构用高强度大六角头螺栓GB /T 1228-91 | 代替GB1228-84 High strength bolts with large hexagon head for steel structures－－钢结构用高强度大六角头螺母GB /T 1229-91 | 代替GB1229-84High strength large hexagon nuts for steel structures－－钢结构用高强度垫圈GB /T 1230-91 | 代替GB1230-84High strength plain washers for steel structures－－钢结构用扭剪型高强度螺栓连接副GB /T 3632-1995 | 代替GB3632-83Sets of torshear type high strength bolt hexagon nut and plain washer for steel structures－－螺栓或螺钉和平垫圈组合件ISO 10644：1998 | GB /T 9074.1-2002 | 代替GB/T 9074.1、9074.14-1988Bolt or screw and washer assemblies with plain washers－－十字槽头螺钉和外锯齿锁紧垫圈组合件UDC 621.882 | GB 9074.2-88 |Cross recessed pan head screw and serrated lock washer external teeth assemblies－－十字槽盘头螺钉和弹簧垫圈组合件UDC 621.882 | GB 9074.3-88 |Cross recessed pan head screw and single coll spring lock washer assemblies－－十字槽盘头螺钉、弹簧垫圈和平垫圈组合件UDC 621.882 | GB 9074.4-88 |Cross recessed pan head screw, single coil spring lock washer assemblies－－十字槽小盘头螺钉和平垫圈组合件UDC 621.882 | GB 9074.5-88 |Cross recessed small pan head screw and small plain washer assemblies－－十字槽小盘头螺钉和大垫圈组合件UDC 621.882 | GB 9074.6-88 |Cross recessed small pan head screw and big plain washer assemblies－－十字槽小盘头螺钉和弹簧垫圈组合件UDC 621.882 | GB 9074.7-88 |Cross recessed small pan head screw and single coil spring lock washer assemblies－－十字槽小盘头螺钉、弹簧垫圈和平垫圈组合件UDC 621.882 | GB 9074.8-88 |Cross recessed small pan head screw, single coil spring lock washer and plain washer assemblies －－十字槽沉头螺钉和锥形锁紧垫圈组合件UDC 621.882 | GB 9074.9-88 |Cross recessed countersunk head screw and countersunk serrated external toothed lock washer assemblies－－十字槽半沉头螺钉和锥形锁紧垫圈组合件UDC 621.882 | GB 9074.10-88 |Cross recessed raised countersunk head screw and countersunk external toothed lock washer assemblies－－十字槽凹穴六角头螺栓和平垫圈组合件UDC 621.882 | GB 9074.11-88 |Cross recessed hexagon bolt with indentation and plain washer assemblies－－十字槽凹穴六角头螺栓和弹簧垫圈组合件UDC 621.882 | GB 9074.12-88 |Cross recessed hexagon bolt with indetation single coil spring lock washer assemblies－－十字槽凹穴六角头螺栓、弹簧垫圈和平垫圈组合件UDC 621.882 | GB 9074.13-88 | Cross recessed hexagon bolt with indetation,single coil lock washer and plain washer assemblies －－六角头螺栓和弹簧垫圈组合件UDC 621.882 | GB 9074.15-88 |Hexagon head bolt and single coil spring lock washer assemblies－－六角头螺栓和外锯齿锁紧垫圈组合件UDC 621.882 | GB 9074.16-88 |Hexagon head bolt and serrated lock washer external teeth assemblies－－六角头螺栓、弹簧垫圈和平垫圈组合件UDC 621.882 | GB 9074.17-88 |Hexagon head bolt,single coil spring lock washer and plain washer assemblies－－自攻螺钉和平垫圈组合件ISO 10510：1999 | GB /T 9074.18-2002 | 代替GB/T 9074.18、9074.19、9074、22、9074、23-1988Tapping screw and washer assemblies with plain washers－－十字槽凹穴六角头自攻螺钉和平垫圈组合件UDC 621.882 | GB 9074.20-88 |Cross recessed hexagon head tapping screw with indentation and plain washer assemblies－－十字槽凹穴六角头自攻螺钉和大垫圈组合件UDC 621.882 | GB 9074.21-88 |Cross recessed hexagon head tapping sorew with indentation and large plain washer assemblies。
公制英制美制螺纹标准叫法
欢迎共阅公制英制美制螺纹标准叫法编辑：信耐精密工具BSPT/NPT ？BSPT是英制圆锥管螺纹标准：指螺纹的牙型角为55°、螺纹具有1：16的锥度1、BSPBSP是英制管螺纹。
不过，有BSP.Tr., BSP.PI., BSP.F.之分。
BSP.Tr.是锥管螺纹，用于密封接合。
BSP.PI.是平行管螺纹，用于密封接合，只一、NPT牙NPT就是一般用途的美国标准锥管螺纹。
其中N表示National (American)美国国家标准，P表示PIPE管子，T表示TAPER 锥形，牙型角为60°。
这种管螺纹在北美地区常用，或在使用ANSI规范中经常看到。
国家标准可查阅GB/T12716-1991我必须注意：在做ANSI规范中须使用NPT牙哦！二、PT牙PT牙为英制锥螺纹，牙型角为55°，密封中最常用。
多用在欧洲和英联邦国家，其实在台湾日本JIS规范也走英制规范，而中国其实也是使用英制螺牙。
属惠氏螺纹家族。
国家标准可查阅 GB/T7306-2000。
英制管螺纹是细牙螺纹，因为粗牙螺纹的牙深大，会严重的降低所切螺纹外径管子的强度。
另外，在实际配小管径管路中，常使用NIPPLE，目的就是外购来的NIPPLE壁厚相对较厚，能保证攻牙部份的强度，同时主管路又不需要厚管壁，这样是为了节约成本。
PF牙是管用平行螺纹。
我必须注意：在做JIS规范中须使用PT牙哦！两位2A为精度等级。
2 、55°圆柱管螺纹的转化55°圆柱管螺纹，来源于英寸制系列，但米制和英寸制国家均广泛采用，用于输送液体经、气体和安装电线的管接头与管子的联接，然而，各国的代号不同，应按下表(对照表)中的国外代号转化为我国代号，现将各国的55°圆柱管螺纹代号列于下表。
国别代号中国 G日本 G、PF英国 BSP、BSPP法国 G德国 R(内螺纹)、K(外螺纹)前苏联 G、TPУБISO Rp3、55°圆锥管螺纹的转化55°圆锥管螺纹，是指螺纹的牙型角为55°、螺纹具有1：16的锥度。
标准件中英文名称对照
德国标准和国际标准、中国标准中英文对照表序号德国标准中文品名英文品名国际标准中国标准Item DIN-Standard Description in Chinese Descriptionin English ISO-StandardGB-Standard1 DIN1 圆锥销taper pins ISO2339 GB1172 DIN7 圆柱销parallel pins ISO2338 GB119-863 DIN84 开槽圆柱头螺钉 slotted cheese head screws ISO1207 GB65-854 DIN85 开槽盘头螺钉slotted pan head screws ISO1580 GB67-855 DIN93 单耳止动垫圈tab washers GB8546 DIN94 开口销split cotter pins ISO1234 GB917 DIN95 开槽半沉头木螺钉slotted raised csk head wood screws GB1018 DIN96 开槽半圆头木螺钉slotted round head wood screws GB999 DIN97 开槽沉头木螺钉slotted countersunk head wood screws GB10010 DIN125-A 平垫plain washers ISO7089 GB97.1-8511 DIN125-B 平垫(带倒角) mediun washers ISO7090 GB97.2-8512 DIN126 平垫plain washers ISO709113 DIN127-A 重型弹垫spring lock washers,tang ends GB724414 DIN127-B 标准弹垫spring lock washers,square ends GB93-8715 DIN128-A 鞍形弹垫single coil spring lock washers GB7245-8716 DIN137-A 弹簧止动垫圈curved spring washers17 DIN137-B 波形弹垫wave spring washers GB95518 DIN186 T型方颈螺栓T-head bolts with square neck GB37-8819 DIN188 T型双接头螺栓T-head bolts with double nip20 DIN258 螺纹圆锥销taper pins with threaded end ISO873721 DIN261 T型头螺栓T-head bolts22 DIN315AF 蝶型螺母(美制) wing nuts amercia form23 DIN315DF 蝶型螺母(德制) wing nuts germany form GB62-8824 DIN316AF 蝶型螺钉(美制) wing screws amercia form25 DIN317DF 蝶型螺钉(德制) wing screws germany form26 DIN319 圆球型盖型螺母ball knobs27 DIN404 开槽带孔球面圆柱头螺钉slotted capstan screws GB832-8828 DIN417 开槽长圆柱端紧定螺钉slotted set srews with full dogpointISO7435GB75-8529 DIN427 开槽平端紧定螺钉(半牙) slotted set srews with chamferedendISO2342GB73-8530 DIN431 小六角特薄细牙螺母pipe nuts with thread GB808-8831 DIN432 外舌止动垫圈external tap GB856-8832 DIN433 小垫圈(用于圆柱头螺钉) washers for cheese head screws ISO7092GB848-9533 DIN434 方斜垫圈(U型) square taper washers for U-section GB852-8834 DIN435 方斜垫圈(I型) square taper washers for I-sections GB852-8835 DIN436 方垫圈square washers36 DIN438 开槽凹端紧定螺钉slotted set with cup point ISO7436 GB74-8537 DIN439 六角薄螺母hexagon thin nuts ISO4035 GB6172-8638 DIN439 细牙六角薄螺母hexagon thin nuts ISO8675 GB6173-8639 DIN440 木螺钉专用垫圈rounds washers for wood constructions ISO709440 DIN443 密封帽sealing caps,push-in type41 DIN444 活节螺栓B 型 eye bolts form B GB798-8842 DIN462 内舌止动垫圈internal tab washers43 DIN463 双耳止动垫圈washers with two taps GB855-8844 DIN464 滚花高头螺钉knurled thumb screws with collar GB834-8845 DIN465 开槽滚花高头螺钉slotted knurled thumb screws with collar46 DIN466 滚花高螺母knurled thumb nuts with collar GB806-8847 DIN467 滚花薄螺母knurled thumb thin nuts GB807-8848 DIN470 锁紧垫圈sealing washers49 DIN471 轴用弹性挡圈 retaining rings for shafts(external),circlips GB894.1-8650 DIN472 孔用弹性挡圈retaining rings for bores(internal),circlips GB893.1-8651 DIN478 方头带垫螺栓square head bolts with collar52 DIN479 方头圆柱底端螺栓square head bolts with half dog point53 DIN480 方头带垫半圆底端螺栓square head bolts with collar,half dog point androunded end54 DIN508 T型槽螺母T-slot nutsISO29955 DIN525 单头螺柱single end studs56 DIN529 地脚螺栓masonry bolts GB799-8857 DIN546 带槽圆螺母slotted round nuts GB817-7658 DIN547 端面带孔圆螺母round nuts with drilled holes in one face GB815-8859 DIN551 开槽平端紧定螺钉slotted sit screws with flat point ISO4776 GB73-8560 DIN553 开槽锥端紧定螺钉slotted set screws with cone point ISO7434 GB71-8561 DIN555 六角螺母hexagon nuts ISO403462 DIN557 方螺母-Csquare nuts GB39-8863 DIN558 六角头螺钉hexagon screws ISO401864 DIN561 六角头圆柱端紧定螺钉hexagon set screws with full dog point65 DIN52 薄型方螺母- Bsquare nuts without bevel(pressed nuts)66 DIN571 六角头木螺钉hexagon head wood screws (coach screws)GB102-8667 DIN580 吊环螺钉lifting eye bolts ISO3266 GB825-7668 DIN582 吊环螺母lifting eye nuts69 DIN601 六角头螺栓hexagon bolts ISO401670 DIN603 大半圆头方颈螺栓(马车螺栓) mushroom head square neck bolts (carriage bolts) ISO8677 GB14-8871 DIN604 沉头带插销马车螺栓flat countersunk nib bolts72 DIN605 沉头长方颈马车螺栓flat countersunk long square neck bolts73 DIN607 半圆头带插销马车螺栓cup head nib bolts74 DIN608 沉头短方颈马车螺栓flat countersunk short square neck bolts75 DIN609 六角头精配螺栓（长螺纹）hexagon fitted bolts,long thread76 DIN610 六角头精配螺栓（短螺纹）hexagon fitted bolts,short thread77 DIN653 滚花平头螺钉 knurled thumb screws thin type GB835-8878 DIN660 半圆头铆钉round head rivets ISO1051 GB867-8679 DIN661 沉头铆钉contersunk head rivets ISO1051 GB869-8680 DIN662 半沉头铆钉raised contersunk head rivets ISO105181 DIN674 大扁头铆钉mushroom head rivets ISO105182 DIN703 重型侧面带孔圆螺母adjusting rings,heavy range (shafting collars)83 DIN705 侧面带孔圆螺母 adjusting rings,light range(shafting collars)GB816-8884 DIN741 卡头wire rope clips85 DIN787T 型槽螺钉T-slot screws ISO29986 DIN835 双头螺柱（牙长=2D）studs-metal (end=2d)GB900-8887 DIN906 内六角锥型闭锁螺钉hexagon socket pipe plugs,conical thread88 DIN908 内六角直型闭锁螺钉hexagon socket screw plugs,cyl. thread89 DIN909 外六角锥型闭锁螺钉hexagon head pipe plugs,conical thread90 DIN910 外六角直型闭锁螺钉hexagon head screw plugs,cyl.thread91 DIN911 内六角扳手socket wrenches ISO293692 DIN912 内六角圆柱头螺钉hexagon socket cap screws ISO4762 GB70-8593 DIN913 内六角平端紧定螺钉hexagon socket set screws withflatpointISO4026 GB77-8594 DIN914 内六角尖端紧定螺钉 hexagon socket set screws withconepoint ISO4027 GB78-8595 DIN915 内六角圆柱端紧定螺钉hexagon socket set screws with dogpoint ISO4028 GB79-8596 DIN916 内六角凹端紧定螺钉hexagon socket set screws with cuppoint ISO4029 GB80-8597 DIN917 薄型盲螺母hexagon cap nuts98 DIN920 开槽小圆柱头螺钉slotted short cheese head screws99 DIN921 开槽大圆柱头螺钉slotted large cheese head screws GB838-88 100 DIN923 开槽圆柱头轴肩螺钉slotted pan head screws with shoulder GB830-88 101 DIN927 开槽无头轴肩螺钉slotted shoulder screws102 DIN928 焊接方螺母square weld nuts GB/T13680-92103 DIN929 焊接六角螺母hexagon weld nuts GB/T13681-92104 DIN931 六角头螺栓（半牙）hexagon head screws ISO4014 GB5782-86 105 DIN933 六角头螺栓（全牙）hexagon head screws ISO4017 GB5783-86 106 DIN934 六角头螺母(1型) hexagon full nuts ISO4032 GB6170-86 107 DIN934 细牙六角头螺母(1型) hexagon full nuts ISO8673 GB6171-86 108 DIN935 开槽六角螺母hexagon slotted and castle nuts ISO7035 GB6178-86 109 DIN936 六角头薄螺母hexagon thin nuts ISO4035 GB6172.1-86 110 DIN937 六角头开槽薄螺母hexagon thin slotted and castlenuts ISO7038 GB6181-86111 DIN938 双头螺距（牙长=1D）studs metal (end=1d) GB897-88 112 DIN939 双头螺距（牙长=1.25D）studs metal (end=1.25d)GB898-88 113 DIN940 双头螺距（牙长=1.5D）studs metal (end=1.5d)114 DIN960 六角头细牙螺栓（半牙）hexagon head bolts,metric fine pitch thread ISO8765 GB5785-86115 DIN961 六角头细牙螺栓（全牙）hexagon head bolts,metric fine pitch thread ISO8676 GB5786-86116 DIN962 头部穿孔六角头螺栓additional shapes and versions for bolts117 DIN963 开槽沉头螺钉slotted countersund head screwsISO 2009 GB68-85118 DIN964 开槽半沉头螺钉slotted raised countersunk oval head screwsISO 2010 GB69-85119 DIN965 十字槽沉头螺钉cross recessed countersunk headscrews ISO7046 GB819-85120 DIN966 十字槽半沉头螺钉cross recessed raised countersunk headscrews ISO7047 GB820-85121 DIN970 六角头螺母hexagon nuts type-1122 DIN971 六角头螺母hexagon nuts type-2123 DIN972 细牙六角头螺母(2型) hexagon nuts with finethread ISO8674 GB6176-86124 DIN975 牙条(全螺纹) threaded rods(studdings) GB15389-94125 DIN976 螺纹销threaded pins(stud bolts)126 DIN979 六角头开槽薄螺母（2型）hexagon thin slotted and castle nuts127 DIN980 全金属六角锁紧螺母（1型）prevailling torque type hexagon nuts,all metall nuts ISO7199 GB6184-86128 DIN981 圆螺母locknuts ISO2982 GB812-88129 DIN982 六角头尼龙锁紧螺母prevailling torque type hexagon nuts,heavy type ,with nylon insert ISO7040 GB889.1-86130 DIN985 六角头薄型尼龙锁紧螺母prevailling torque type hexagon nuts,heavy type ,with nylon insert ISO10511 GB6172.2-86131 DIN986 六角盖型尼龙锁紧螺母prevailling torque typedomed capnuts with nylon insert132 DIN988 配合垫片shim rings133 DIN1052 木材连接用垫片washers for timber connectors134 DIN1151 沉头钢钉round plain head nails135 DIN1440 销钉专用垫片A型plain washers for clevis pins(A型) ISO8738136 DIN1441 销钉专用垫片plain washers for clevis pins137 DIN1444 带头销钉clevis pins with head ISO2341138 DIN1471 圆锥型槽销grooved pins,taper grooved ISO8744 GB/T13829.2 139 DIN1472 圆锥型槽销(半槽)grooved pins,taper grooved halflength ISO8745 GB/T13829.2140 DIN1473 平行槽销(带倒角) grooved pins,parallel grooved fulllength ISO8740141 DIN1474 前端凹槽槽销grooved pins,reserve grooved halflength ISO8741142 DIN1475 中部凹槽槽销grooved pins,centre grooved ISO8742143 DIN1476 圆头槽销grooved pins with round head ISO8746 GB/T13829.3 144 DIN147 7沉头槽销grooved pins with countersunk head ISO8747145 DIN1479 六角螺母棒turnuckles(centre parts),made out of hexagon bar146 DIN1480 花篮螺栓turnuckles with eye bolt and hook bolt147 DIN1481 弹性圆柱销spring pins,heavy type ISO8752 GB879-86 148 DIN1587 组合式盖型螺母hexagon domed cap nuts GB802-88 149 DIN1804 开槽圆螺母（配合沟头扳手）slotted round nuts for hook spanner150 DIN1816 圆螺母（带插销孔）round nuts with set holes151 DIN2093 盘型弹簧垫圈disc springs152 DIN3017 喉箍hose clamps153 DIN3404 润滑油嘴（旋扭头）lubricating nipples,button head154 DIN3567 管夹shackles for conduilts155 DIN3570 U型螺栓stirrup bolts(U-bolts)156 DIN6319 球面垫圈spherical washers,conical seats GB849-88157 DIN6325 圆柱销parallel pins ISO8734158 DIN6330 厚六角螺母hexagon nuts ,1.5d GB56-88159 DIN6331 厚六角法兰面螺母hexagon nuts ,1.5d with collar GB6177-86 160 DIN6334 长六角螺母hexagon nuts ,3d161 DIN6797-A 外齿锁紧垫圈external teeth lock washers GB862.1-87 162 DIN6797-I 内齿锁紧垫圈internal teeth lock washers GB861.1-87 163 DIN6798-A 外锯齿锁紧垫圈external teeth serrated lock washers GB862.2-87 164 DIN6798-I 内锯齿锁紧垫圈internal teeth serrated lock washers GB861.2-87 165 DIN6799 开口挡圈retaining rings for shafts(E-rings),circlips GB896-76 166 DIN6885 平键（A型）parallel keys(form A ) ISO773/2491167 DIN6888 半圆键woodruff keys ISO3912168 DIN6899 嵌环（支撑环）thimbles169 DIN6900 机器螺钉和垫圈组合件screws and washersassemblies GB9074.1-.17170 DIN6901 自攻螺钉和垫圈组合件tapping screws and washersassemblies GB9074.18-.23171 DIN6912 薄型带孔内六角圆柱头螺钉hexagon socket head cap screws with hole,lowhead172 DIN6914 大六角头螺栓hexagon head bolts with large head(friction grip bolts)173 DIN6915 大六角螺母hexagon nuts with large wideth across flat(friction grip nuts)174 DIN6916 大垫圈round washers for friction grip bolts175 DIN6917 楔型方垫圈spuare taper washers for friction grip bolts on T-sections176 DIN6923 六角法兰面螺母hexagon flange nuts ISO4161 GB6177-86 177 DIN6925 全金属六角锁紧螺母(2型）prevailing torque type hexagon nuts,all metallic nuts ISO7042 GB6185.1-2000178 DIN7337 开口型抽芯铆钉（沉头、扁圆头）blind rivets GB12617/12618 179 DIN7338 扁平头半空心/全空心铆钉rivets for brake and clutchlining GB875/975-86180 DIN7343 螺旋夹紧销spiral pins ISO8750181 DIN7346 轻型弹性圆柱销spring pins,light type ISO13337182 DIN7349 重型弹性圆柱销用垫圈washers for bolts with heavy type spring pinss 183 DIN7500 ISO公制螺纹螺钉(多种头型) threadforming screwsfor ISO-metricthread184 DIN7504 自攻自钻螺钉(多种头型) self-drilling tapping screws185 DIN7513 开槽切削螺纹螺钉(多种头型) thread cutting screws186 DIN7516 十字槽切削螺纹螺钉(多种头型) thread cutting screws cross recess187 DIN7965 T型四爪螺母tee nuts with pronge188 DIN7968 钢结构用六角头螺栓连接副hexagon head fitted bolts for steel structures GB1228/1229/1230189 DIN7971 开槽盘头自攻螺钉pan head tapping screws withslot ISO1481 GB5282-85190 DIN7972 开槽沉头自攻螺钉countersunk flat head tapping screws with slot ISO1482 GB5283-85191 DIN7973 开槽半沉头自攻螺钉raised countersunk oval head tapping screws with slot ISO1483 GB5284-85192 DIN7976 六角头自攻螺钉hexagon tapping screws ISO1479 GB5285-85 193 DIN7980 圆柱头螺钉用弹簧垫圈spring lock washers for screws with cylindrical headsISO8738194 DIN7981 十字槽盘头自攻螺钉pan head tapping screws with crossrecessed ISO7049 GB845-85195 DIN7982 十字槽沉头自攻螺钉countersunk flat head tapping screws with cross recessed ISO7050 GB846-85196 DIN7983 十字槽半沉头自攻螺钉raised countersunk oval head tapping screws withcross recessed ISO7051 GB847-86197 DIN7984 薄型内六角圆柱头螺钉hexagon socket head cap screws with，reduced head198 DIN7985 十字槽盘头螺钉pan head screws with cross recessed ISO7045GB818-85199 DIN7989 钢结构用垫圈washers for steel structures GB1230-84 200 DIN7990 钢结构用六角头螺栓 hexagon head bolts for steel structuresGB1229-84 201 DIN7991 内六角沉头螺钉hexagon socket countersunk head screws ISO10642 202 DIN7993 轴用钢丝挡圈roundwire snap rings for shafts GB895.2-86 203 DIN7995 十字槽半沉头木螺钉cross recessed raised countersunk head wood screws GB952-86204 DIN7996 十字槽圆头木螺钉cross recessed round head wood screwsGB950-86205 DIN7997 十字槽沉头木螺钉cross recessed countersunk head wood screws GB951-86206 DIN8140 螺纹护套（普通\自锁等）ciol inserts,coarse,fine thread,silf locking207 DIN9021 大外径垫圈washers,outside diameterappro.3d ISO7093 GB96-85208 DIN11024 弹簧卡子spring cotter for a bolt209 DIN13257 平板螺栓belting bolts (elevator bolts)210 DIN18182 干壁钉（墙板钉）dry wall screws211 DIN28129 环型螺母lifting nuts(eye nuts)GB63-88212 DIN70952 圆螺母用止退垫圈tab washers for slotted round nuts GB858-88。
标准件中英文对照表
NABS紧固件知识系列143 铜螺帽BRASS NUTS44 突缘尼龙盖帽FLANGE NYLON INSERT LOCK NUTS45 锌压属螺帽ZINC DIE CASTING NUTS46 圆螺帽ROUND NUTS47 制止螺帽SLIDING NUTS48 重型车螺帽HEAVY DUTY WHEEL HUB NUTS49 自锁螺帽SELF-LOCKING NUTS螺丝,螺栓SCREW(BOLTS)50 T 头螺丝T HEAD BOLTS51 U 型螺栓U BOLTS52 板模螺丝CONSTRUCTION BOLTS53 不锈钢自削螺丝STAINLESS STEEL THREAD CUTTING SCREWS54 不锈钢大螺丝STAINLESS STEEL BOLTS55 不锈钢高低牙螺丝STAINLESS STEEL HIGH-LOW THREAD SCREWS56 不锈钢固定螺丝STAINLESS STEEL HEX SOCKET CAP SCREWS57 不锈钢机械螺丝STAINLESS STEEL MACHINE SCREWS58 不锈钢宽牙螺丝STAINLESS STEEL COARSE THREAD SCREWS59 不锈钢六角螺丝STAINLESS STEEL HEX SOCKET CAP SCREWS60 不锈钢木螺丝STAINLESS STEEL WOOD SCREWS61 不锈钢内六角螺丝STAINLESS STEEL HEX SOCKET CAP SCREWS62 不锈钢三角牙螺丝STAINLESS STEEL TRI-LOBULAR THREAD SCREWS63 不锈钢特殊螺丝SPECIAL STAINLESS STEEL SCREWS64 不锈钢小螺丝STAINLESS STEEL SHEET METAL SCREWS65 不锈钢自攻螺丝STAINLESS STEEL SELF TAPPING SCREWS66 不锈钢钻尾螺丝STAINLESS STEEL SELF DRILLING SCREWS67 车辆(汽车)螺丝、螺帽AUTOMOTIVE FASTENERS68 大尺寸螺栓BIG SIZE BOLTS69 大头马车螺丝STEP BOLTS70 单向螺丝ONE WAY LAG SCREWS71 电梯螺丝ELEVATOR BOLTS72 电子螺丝ELECTRONIC SCREWS73 飞机特殊扣件SOURCE CONTROL BOLTS74 复合材料用螺丝PARTICLE BOARD SCREWS75 复合材料用螺丝（夹板用） PARTICLE BOARD SCREWS76 复合材料钻尾螺丝BI-METAL SELF DRILLING SCREWS77 高低牙螺丝HIGH LOW SCREWS78 高张力螺栓HIGH STRENGTH BOLTS79 勾头螺栓HOOK BOLTS80 固定螺丝SET SCREWS81 管夹螺丝HOSE CLAMP SCREWS82 轨道螺栓(鱼尾螺丝) TRACK BOLTS83 航天用螺丝AEROSPACE FASTENERS84 合金钢螺丝ALLOY STEEL SCREWS85 环首螺丝EYE BOLTS86 货柜螺丝CONTAINER SCREWS87 基础螺栓FOUNDATION BOLTS88 机(踏)车用螺丝、轴心SCREWS AND SHAFTS FOR MOTORCYCLE OR BICYCLE89 机械螺丝MACHINE SCREWS92 剪力钉(焊接螺丝) WELDING STUDS93 建业螺丝BUILDING FASTENERS94 铰链螺丝HINGE SCREWS95 宽牙螺丝（粗牙螺丝） COARSE THREAD SCREWS96 拉栓BLIND BOLTS97 犁壁螺丝PLOW BOLTS98 链带螺丝COLLATED SCREWS99 六角机械螺丝HEX HEAD MACHINE BOLTS100 六角螺丝(栓) HEX HEAD CAP SCREWS(HEX BOLTS)101 六角木牙螺丝HEX LAG BOLTS102 铝螺丝ALUMINUM SCREWS103 轮壳螺栓WHEEL BOLTS104 螺椿栓STUD BOLTS105 螺丝附华司组合SCREWS AND WASHERS ASSEMBLED(SEMS)106 螺旋椿SCREW STUDS107 马车螺丝CARRIAGE BOLTS108 马桶螺丝TOILET CLOSET BOLTS109 面板螺丝PANEL FASTENERS110 拇指螺丝THUMB SCREWS111 木螺丝WOOD SCREWS112 耐候钢螺丝CORTEN STEEL HEAVY HEX BOLTS113 内六角固定螺丝HEX SOCKET SET SCREWS114 内六角孔螺丝HEX SOCKET CAP SCREWS115 扭矩控制螺栓T.C.BOLTS116 其它特殊螺丝SPECIAL SCREWS OR BOLTS117 墙用螺丝DRYWALL SCREWS118 三角牙螺丝TRILOBULAR THREAD SCREWS119 双头牙螺丝DOUBLE END SCREWS HANGER BOLT120 水泥螺丝CONCRETE SCREWS121 四角螺丝SQUARE HEAD BOLTS122 四角头固定螺丝SQUARE SET SCREWS123 塑板螺丝CHIPBOARD SCREWS124 塑料螺丝PLASTIC SCREWS125 钛、锆、钼、铌等螺丝、零件、材料TI,ZR,MO,NB PARE METAL BOLTS PARTS 126 钛合金螺丝TITANIUM ALLOY BOLTS127 钛合金膨胀螺丝TITANIUM ALLOY EXPANSION BOLTS128 套挂螺栓及螺丝TOGGLE BOLTS129 套挂螺丝TOGGLE BOLTS130 特长螺丝SPECIAL LONGER SCREWS131 铜螺丝BRASS SCREWS132 突缘螺丝FLANGE BOLTS133 微小精密螺丝MICRO SCREWS134 锌蝶螺丝DIE CAST WING SCREWS; ZINC ALLOY135 旋入螺丝DRIVE SCREWS136 翼形螺丝WING SCREWS137 针车用螺丝、轴心SCREWS AND SHAFTS FOR SEWING MACHING138 止付螺丝SOCKET SET SCREWS139 重型车螺丝HEAVY DUTY WHEEL HUB BOLTS140 自攻螺丝SELF TAPPING SCREWS141 自削螺丝THREAD CUTTING SCREWS其它特殊品SPECIALITY143 E 型环E-RINGS144 R 型销SNAP PINS145 不锈钢华司STAINLESSSTEEL WASHERS146 不锈钢链STAINLESS STEEL CHAINS147 不锈钢输送带轮用轨道STAINLESS WHEEL'S RACK FOR TRANSPORTER148 不锈钢牙条棒STAINLESS STEEL HREAD ROD149 长形拉帽BLIND RIVET NUTS150 超音螺纹压入式螺纹自动锁扣THREADED INSERTS FOR PLASTIC INJECTION MOULDEINGS 151 齿轮GEARS152 船舶链ANCHOR CHAIN153 搓牙铁钉THREAD NAILS154 弹簧蝴蝶夹SPRING WINGS155 弹簧华司SPRING WASHERS156 弹片CLIPS157 轭子T-YOKE158 钢铁钉STEEL AND IRON NAILS159 格式管夹、管束PIPE HANGER160 工具套筒组件SOCKET WRENCH SETS161 工业用链INDUSTRIAL STEEL LINK CHAINS162 狗链DOG CHAINS163 管形铆钉TUBULAR RIVETS164 合金钢工具ALLOY STEEL TOOLS165 华司WASHERS166 机车离合器零件MANUFACTURE OF MOTORCYCLE'S CVT PARTS167 鸡眼钉EYELETS RIVETS168 脚踏车链锁BICYCLE CHAIN LOCKS169 金属板镶嵌组件及自动夹扣组件SHEET METAL FASTENERS170 卷钉COIL NAILS171 开叉钉SPLIT DRIVE ANCHORS172 开口铆钉BLIND RIVETS173 开口销COTTER PINS174 拉钉BLIND RIVETS175 拉帽BLIND NUTS176 喇叭头轭铁U-YOKE,T-YOKE FOR SPEAKER177 冷锻零件COLD FORMING PART178 链条用滚子ROLLER FOR ROLLER CHAIN179 六角扳手HEXAGON KEYS180 轮胎链TIRE CHAINS181 螺栓模BOLT HEADING DIES182 螺丝、螺帽、五金、DIY 扣件FASTENERS183 螺丝起子BIT184 螺纹护套RECOIL INSERTS185 螺旋锔及螺旋圈SCREW HOOK AND SCREW RINGS186 罗拉CHAIN ROLLER187 马达轴承轴心组件BEARING SHAFT(MOTOR)188 铆钉RIVETS189 膨胀螺栓EXPANSION ANCHOR BOLTS190 其它特殊铆钉OTHER SPECIL RIVETS193 手动拉钉钳HAND RIVETER194 钛合金铆钉TITAIUM ALLOY RIVETS195 特殊铆合扣件COLLARS(A BLINDFASTENER FOR HUCK INTL)196 拖链安全链TOW CHAINS AND SAFETY CHAINS197 销PINS198 牙条棒THREAD ROD199 闸、锁LATCHES AND KEEPER ASSEMBLEDS200 真空热处理VACUUM HEAT TREATMENT201 中空钉SEMI-TUBULAR RIVET202 轴承轴心BEARING SHAFT203 装饰链DECORATIVE CHAINS204 自攻螺纹衬套ENSAT THREADED INSERTS线材/设备WIRE(EQUIPMENTS)205 ISO 品质保证系统ISO QUALITY ASSURANCE SYSTEM206 棒钢STEEL BAR(HEX/ROUND/SQUARE)207 不锈钢冷锻线材STAINLESS STEEL COLD HEADING WIRE208 不锈钢条棒STAINLESS STEEL BAR(ROUND/HEX/SQUARE)209 不锈钢线(抽线后) STAINLESS STEEL DRAW WIRE210 不锈钢线材STAINLESS STEEL WIRE211 不锈钢线材及盘元STAINLESS STEEL WIRE AND ROD212 超防锈复合瓷膜CERAMIC COATING213 成品自动收线机NON-STOP COILER214 成型冲模HEADER PUNCHES IN VARIOUS DRIVES215 冲模PUNCH DIES216 冲子PUNCH PINS217 搓牙机铁屑分离装置THREAD CHIP SEPARATOR218 倒立式滑落型伸线机HANDSTAND TYPE WIRE DRAWING MACHINE219 德国SCHATZ 扭力机代理REPRESENTATIVE OF SCHATZ TORQUE MACHIN220 电镀化学原料VARIOUS ELECTROPLATING CHEMICALS221 镀钛处理(TiN)专业加工服务TiN HARD COATING FOR CUTTING TOOLS AND PUNCH BY PVD 222 高中低周波感应加热炉HIGH,MEDIUM,LOW FREQUENCY INDUCTION HEATER223 各式螺丝类产品自动包装AUTOMATIC PACKAGING FOR ALL KINDS OF PACKAGING224 攻牙机TAPPING MACHINE225 滚牙轮THREAD ROLLING DIES226 合金钢线材盘元ALLOY STEEL WIRE ROD227 黑铁丝BLACK WIRE228 环规、牙规、三线规校正CALIBRATION FOR RING GAGE, ATHREAD GAGE, 3 WIRE GAGE 229 环规校正CALIBRATION FOR RING GAGE230 黄铜棒线BRASS WIRE AND ROD231 机(踏)车用螺丝成型机SCREW FOR MOTORCYCLE OR BICYCLE HEADING MACHINE232 机械镀锌MECHANICAL GALVANIZED233 鸡眼上下模EYELETS DIES234 精抽自动收线机NON-STOP COILER(SKINPASS)235 精密油压滚牙机HYDRAULIC THREAD ROLLING MACHINES236 空心打头机HOLLOW HEADING MACHINE237 快削钢线材盘元FREE CUTTING STEEL WIRE ROD238 拉钉打头机BLIND RIVET HEADING MACHINE239 连续式光辉调质淬火炉CONTINUOUS BRIGHT HARDENING QUENCHING FURNACE242 磷青铜线PHOSPHATE BRONZE WIRE243 六角整头模TRIMMING DIES HEXAGAN244 螺帽成型模NUTS FORMERS245 螺帽模NUT FORMING DIES246 螺丝、螺帽成型攻牙专用油FORMING AND TAPPING OILS FOR BOLTS AND NUTS FORMERS 247 螺丝、螺帽成型机BOLT FORMERS,NUTS FORMERS,HEADERS248 螺丝、螺帽品检量测仪器FASTENERS INSPECTION AND MEASUREMENT INSTRUMENTS249 螺丝、螺帽热处理BOLT NUT AND SCREWS HEAT TREATMENT250 螺丝、螺帽热处理炉BOLT NUT AND SCREWS HEAT TREATMENT FURNACES251 螺丝、螺帽五金等检验INSPTECTION SERVICES FOR FASTENERS AND HARDWARE252 螺丝打头机HEADING MACHINE253 螺丝割尾及特殊割遘加工MACHINE SCREW SHANK SLOTTING254 螺丝割尾加工机械AUTOMATIC THREAD SLOTTING MACHINE255 螺丝攻、车刀、模具TAPS DIES AND TOOLS256 螺丝制造成型机械AUTOMATIC TRIMMING MACHINE257 螺丝制造搓牙机械AUTOMATIC THREAD ROLLING MACHINE258 螺丝制造高速搓牙机械HIGH SPEED AUTOMATIC THREAD ROLLING MACHINE259 螺丝钻孔加工SCREW SHANK DRILLING260 罗拉成型机ROLLERS FORMERS261 迷你成型机MINI-FORMERS262 模具TOOLS263 磨光棒钢BRIGHT STEEL BAR(HEX/ROUND/SQUARE)264 气动拉钉机AIR RIVETER265 球状化电器炖炉CARBURIZING FURNACE VACUUM AND BELL TYPE FURNACE266 球状化热处理炉SPHEROIDIZING HEAT TREATMENT FURNACE267 球状化线材ANNEALING WIRE AND ROD268 热浸镀锌螺丝、螺帽HOT DIP GALVANIZING BOLTS AND NUTS269 生产管理系统PRODUCTION CONTROL SYSTEM270 十字冲模HEADER PUNCHES IN VARIOUS DRIVES271 碳化钨模具TUNGSTEN CARBIDE DIE272 套高成型机SOCKETS FORMERS273 特殊零件成型机PARTS FORMING MACHING274 铜合金线COPPER ALLOY WIRE275 物料管理系统MATERIAL CONTROL SYSTEM276 线材IRON OR STEEL WIRE277 线材盘元IRON OR STEEL WIRE ROD278 线切割线E.D.M CUTTING WIRE279 牙板THREAD ROLLING DIES PLATES280 洋白铜线NICKEL SILVER WIRE281 一般线材、盘元、螺丝合金炖炉SPHEROIDIZING BRIGHT ANNEALING FURNACE282 一般线材、盘元、退火炉GENERAL WIRE,WIRE ROD,ANNEALING FURNACE283 止付螺丝成型机SET SCREWS FORMERS284 中、高热镀锌光辉连续炉CONTINUOUS BRIGHT HEAT TREAT FURNACE285 转回90 度碾线头机90 REVOLVING WIRE TWISTING MACHINE286 自动包装机AUTOMATIC PACKING MACHINE。
标准件国标号和命名规则STANDARD PARTS (中英对照)
GB/T 848-2002
小垫圈A级
Plain washers-Small series-Product grade A
GB/T 849-1988
球面垫圈
Washers with ball face
GB/T 852-1988
工ection
六角薄螺母
Hexagon thin nuts(chamfered)
GB/T 6173-2000
六角薄螺母细牙
Hexagon thin nuts (chamfered) with fine pitch thread
GB/T 6178-1986
1型六角开槽螺母A和B级
Hexagon slotted and castle nuts,style 1--Product grades A and B
GB/T 5785-2000
六角头螺栓细牙
Hexagon head bolts with fine pitch thread
GB/T 5786-2000
六角头螺栓细牙全螺纹
Hexagon head bolts with fine pitch thread-Full thread
GB/T 798-1988
标准件常识
STANDARD PARTS IN COMMON
BY:John.CJ
标记含义CODE MEANING
□□□□/□ □□□□-□□□□M□□×□□ □□
等级GRADE
公称长度nominal length
公称直径NOMINAL DIAMETER
米制METRIC
发布年份YEAR OF ISSUE
GB/T 12618-1990
开口型扁圆头抽芯铆钉
标准件中英文对照表螺母nuts
NABS-全球紧固件配套服务公司NABS紧固件知识系列1 更多的请访问/ 标准件中英文对照表螺母NUTS1 SLN-自动防松螺帽SLN SELF-LOCKING NUTS2 T 形螺帽T NUTS3 U 形螺帽U NUTS4 壁虎螺帽ANCHOR NUTS5 薄型螺帽HEX JAM NUTS6 不锈钢六角轮缘尼龙螺帽STAINLESS STEEL FLANGE NYLON INSERT LOCK NUTS7 不锈钢六角螺帽STAINLESS STEEL HEX NUTS8 不锈钢六角重型螺帽STAINLESS STEEL HEAVY HEX NUTS9 不锈钢螺帽STAINLESS STEEL NUTS10 不锈钢尼龙嵌入螺帽STAINLESS STEEL NYLON INSERT LOCK NUTS11 不锈钢突缘螺帽STAINLESS STEEL FLANGE NUTS12 齿花螺帽CLINCH NUTS13 齿形螺帽KEP NUTS14 大尺寸螺帽BIG SIZE NUTS15 弹簧螺帽SPRING NUTS16 蝶型螺帽WING NUTS17 高脚螺帽HEX COUPLING NUTSHIGH NUTS18 高张力螺帽HEIGH STRENGTH NUTS19 管用螺帽PIPE NUTS20 焊接螺帽WELD NUTS21 合金钢螺帽ALLOY STEEL NUTS22 环首螺帽EYE NUTS23 机械螺丝用六角螺帽HEX MACHINE SCREW NUT24 建业用螺帽STRUCTURAL NUTS25 金属预置扭矩式螺帽ALL-METAL PREVAILING TORQUE TYPE NUTS26 六角盖头螺帽HEX CAP NUTS27 六角割沟螺帽HEX SLOTTED NUT28 六角锯齿螺帽HEX SERRATED NUTS29 六角轮缘螺帽HEX FLANGE NUTS30 六角重型螺帽HEAVY HEX NUTS31 铝螺帽ALUMINUM NUTS32 轮壳螺帽WHEEL NUTS33 耐候钢六角重型螺帽CORTEN STEEL HEAVY HEX NUTS34 尼龙嵌入防松螺帽NYLON INSERT LOCK NUTS35 盘形华司螺帽CONICAL WASHER NUTS36 平面华司螺帽FLAT WASER NUTS37 普通六角螺帽HEX NUTS38 其它特殊螺帽SPECIAL NUTS39 四角螺帽SQUARE NUTS40 铁盖尼龙圈组合盖帽DIN 986 DOMED CAP NUTS41 铁盖袋帽CLOSED END ACORN NUTS 1/742 铁器焊接袋帽ACORN CAP NUTS NABS-全球紧固件配套服务公司43 铜螺帽BRASS NUTS44 突缘尼龙盖帽FLANGE NYLON INSERT LOCK NUTS45 锌压属螺帽ZINC DIE CASTING NUTS46 圆螺帽ROUND NUTS47 制止螺帽SLIDING NUTS48 重型车螺帽HEAVY DUTY WHEEL HUB NUTS49 自锁螺帽SELF-LOCKING NUTS螺丝螺栓SCREWBOLTS50 T 头螺丝T HEAD BOLTS51 U 型螺栓U BOLTS52 板模螺丝CONSTRUCTION BOLTS53 不锈钢自削螺丝STAINLESS STEEL THREAD CUTTING SCREWS54 不锈钢大螺丝STAINLESS STEEL BOLTS55 不锈钢高低牙螺丝STAINLESS STEEL HIGH-LOW THREAD SCREWS56 不锈钢固定螺丝STAINLESS STEEL HEX SOCKET CAP SCREWS57 不锈钢机械螺丝STAINLESS STEEL MACHINE SCREWS58 不锈钢宽牙螺丝STAINLESS STEEL COARSE THREAD SCREWS59 不锈钢六角螺丝STAINLESS STEEL HEX SOCKET CAP SCREWS60 不锈钢木螺丝STAINLESS STEEL WOOD SCREWS61 不锈钢内六角螺丝STAINLESS STEEL HEX SOCKET CAP SCREWS62 不锈钢三角牙螺丝STAINLESS STEEL TRI-LOBULAR THREAD SCREWS63 不锈钢特殊螺丝SPECIAL STAINLESS STEEL SCREWS64 不锈钢小螺丝STAINLESS STEEL SHEET METAL SCREWS65 不锈钢自攻螺丝STAINLESS STEEL SELF TAPPING SCREWS66 不锈钢钻尾螺丝STAINLESS STEEL SELF DRILLING SCREWS67 车辆汽车螺丝、螺帽AUTOMOTIVE FASTENERS68 大尺寸螺栓BIG SIZE BOLTS69大头马车螺丝STEP BOLTS70 单向螺丝ONE WAY LAG SCREWS71 电梯螺丝ELEVATOR BOLTS72 电子螺丝ELECTRONIC SCREWS73 飞机特殊扣件SOURCE CONTROL BOLTS74 复合材料用螺丝PARTICLE BOARD SCREWS75复合材料用螺丝（夹板用）PARTICLE BOARD SCREWS76 复合材料钻尾螺丝BI-METAL SELF DRILLING SCREWS77 高低牙螺丝HIGH LOW SCREWS78 高张力螺栓HIGH STRENGTH BOLTS79 勾头螺栓HOOK BOLTS80 固定螺丝SET SCREWS81 管夹螺丝HOSE CLAMP SCREWS82 轨道螺栓鱼尾螺丝TRACK BOLTS83 航天用螺丝AEROSPACE FASTENERS84 合金钢螺丝ALLOY STEEL SCREWS85 环首螺丝EYE BOLTS86 货柜螺丝CONTAINER SCREWS87 基础螺栓FOUNDATION BOLTS88 机踏车用螺丝、轴心SCREWS AND SHAFTS FOR MOTORCYCLE OR BICYCLE89 机械螺丝MACHINE SCREWS90 夹板用螺丝PARTICLE BOARD SCREWS 2/791 家具螺丝FURNITURE SCREWS NABS-全球紧固件配套服务公司92 剪力钉焊接螺丝WELDING STUDS93建业螺丝BUILDING FASTENERS94 铰链螺丝HINGE SCREWS95 宽牙螺丝（粗牙螺丝）COARSE THREAD SCREWS96 拉栓BLIND BOLTS97 犁壁螺丝PLOW BOLTS98 链带螺丝COLLATED SCREWS99 六角机械螺丝HEX HEAD MACHINE BOLTS100 六角螺丝栓HEX HEAD CAP SCREWSHEX BOLTS101 六角木牙螺丝HEX LAG BOLTS102 铝螺丝ALUMINUM SCREWS103 轮壳螺栓WHEEL BOLTS104 螺椿栓STUD BOLTS105 螺丝附华司组合SCREWS AND WASHERS ASSEMBLEDSEMS106 螺旋椿SCREW STUDS107 马车螺丝CARRIAGEBOLTS108 马桶螺丝TOILET CLOSET BOLTS109 面板螺丝PANEL FASTENERS110 拇指螺丝THUMB SCREWS111 木螺丝WOOD SCREWS112 耐候钢螺丝CORTEN STEEL HEAVY HEX BOLTS113 内六角固定螺丝HEX SOCKET SET SCREWS114 内六角孔螺丝HEX SOCKET CAP SCREWS115 扭矩控制螺栓T.C.BOLTS116 其它特殊螺丝SPECIAL SCREWS OR BOLTS117 墙用螺丝DRYWALL SCREWS118 三角牙螺丝TRILOBULAR THREAD SCREWS119 双头牙螺丝DOUBLE END SCREWS HANGER BOLT120 水泥螺丝CONCRETE SCREWS121 四角螺丝SQUARE HEAD BOLTS122 四角头固定螺丝SQUARE SET SCREWS123 塑板螺丝CHIPBOARD SCREWS124 塑料螺丝PLASTIC SCREWS125 钛、锆、钼、铌等螺丝、零件、材料TIZRMONB PARE METAL BOLTS PARTS126 钛合金螺丝TITANIUM ALLOY BOLTS127 钛合金膨胀螺丝TITANIUM ALLOY EXPANSION BOLTS128 套挂螺栓及螺丝TOGGLE BOLTS129 套挂螺丝TOGGLE BOLTS130 特长螺丝SPECIAL LONGER SCREWS131 铜螺丝BRASS SCREWS132 突缘螺丝FLANGE BOLTS133 微小精密螺丝MICRO SCREWS134 锌蝶螺丝DIE CAST WING SCREWS ZINC ALLOY135 旋入螺丝DRIVE SCREWS136 翼形螺丝WING SCREWS137 针车用螺丝、轴心SCREWS AND SHAFTS FOR SEWING MACHING138 止付螺丝SOCKET SET SCREWS139 重型车螺丝HEAVY DUTY WHEEL HUB BOLTS140 自攻螺丝SELF TAPPING SCREWS141 自削螺丝THREAD CUTTING SCREWS142 钻尾螺丝SELF DRILLING SCREWS 3/7 NABS-全球紧固件配套服务公司其它特殊品SPECIALITY143 E 型环E-RINGS144 R 型销SNAP PINS145 不锈钢华司STAINLESSSTEEL WASHERS146不锈钢链STAINLESS STEEL CHAINS147 不锈钢输送带轮用轨道STAINLESS WHEELS RACK FOR TRANSPORTER148 不锈钢牙条棒STAINLESS STEEL HREAD ROD149 长形拉帽BLIND RIVET NUTS150 超音螺纹压入式螺纹自动锁扣THREADED INSERTS FOR PLASTIC INJECTION MOULDEINGS151 齿轮GEARS152 船舶链ANCHOR CHAIN153 搓牙铁钉THREAD NAILS154 弹簧蝴蝶夹SPRING WINGS155 弹簧华司SPRING WASHERS156 弹片CLIPS157 轭子T-YOKE158 钢铁钉STEEL AND IRON NAILS159 格式管夹、管束PIPE HANGER160 工具套筒组件SOCKET WRENCH SETS161 工业用链INDUSTRIAL STEEL LINK CHAINS162 狗链DOG CHAINS163 管形铆钉TUBULAR RIVETS164 合金钢工具ALLOY STEEL TOOLS165 华司WASHERS166 机车离合器零件MANUFACTURE OF MOTORCYCLES CVT PARTS167 鸡眼钉EYELETS RIVETS168 脚踏车链锁BICYCLE CHAIN LOCKS169 金属板镶嵌组件及自动夹扣组件SHEET METAL FASTENERS170 卷钉COIL NAILS171 开叉钉SPLIT DRIVE ANCHORS172 开口铆钉BLIND RIVETS173 开口销COTTER PINS174 拉钉BLIND RIVETS175 拉帽BLIND NUTS176 喇叭头轭铁U-YOKET-YOKE FOR SPEAKER177 冷锻零件COLD FORMING PART178 链条用滚子ROLLER FOR ROLLER CHAIN179 六角扳手HEXAGON KEYS180 轮胎链TIRE CHAINS181 螺栓模BOLT HEADING DIES182 螺丝、螺帽、五金、DIY 扣件FASTENERS183 螺丝起子BIT184 螺纹护套RECOIL INSERTS185 螺旋锔及螺旋圈SCREW HOOK AND SCREW RINGS186 罗拉CHAIN ROLLER187 马达轴承轴心组件BEARING SHAFTMOTOR188 铆钉RIVETS189 膨胀螺栓EXPANSION ANCHOR BOLTS190 其它特殊铆钉OTHER SPECIL RIVETS191 汽车特殊杆接件SPECIALAUTO-MOBILE FASTENER AS YOUR NEEDS 4/7192 实心梢CLEVIS PINS AND STRAIGHT PINS NABS-全球紧固件配套服务公司193 手动拉钉钳HAND RIVETER194 钛合金铆钉TITAIUM ALLOY RIVETS195 特殊铆合扣件COLLARSA BLINDFASTENER FOR HUCK INTL196 拖链安全链TOW CHAINS AND SAFETY CHAINS197 销PINS198 牙条棒THREAD ROD199 闸、锁LATCHES AND KEEPER ASSEMBLEDS200 真空热处理VACUUM HEAT TREATMENT201 中空钉SEMI-TUBULAR RIVET202 轴承轴心BEARING SHAFT203 装饰链DECORATIVE CHAINS204 自攻螺纹衬套ENSAT THREADED INSERTS线材/设备WIREEQUIPMENTS205 ISO 品质保证系统ISO QUALITY ASSURANCE SYSTEM206 棒钢STEEL BARHEX/ROUND/SQUARE207 不锈钢冷锻线材STAINLESS STEEL COLD HEADING WIRE208 不锈钢条棒STAINLESS STEEL BARROUND/HEX/SQUARE209 不锈钢线抽线后STAINLESS STEEL DRAW WIRE210 不锈钢线材STAINLESS STEEL WIRE211 不锈钢线材及盘元STAINLESS STEEL WIRE AND ROD212 超防锈复合瓷膜CERAMIC COATING213 成品自动收线机NON-STOP COILER214 成型冲模HEADER PUNCHES IN VARIOUS DRIVES215 冲模PUNCH DIES216 冲子PUNCH PINS217 搓牙机铁屑分离装置THREAD CHIP SEPARATOR218 倒立式滑落型伸线机HANDSTAND TYPE WIRE DRAWING MACHINE219 德国SCHATZ 扭力机代理REPRESENTATIVE OF SCHATZ TORQUE MACHIN220 电镀化学原料VARIOUS ELECTROPLATINGCHEMICALS221 镀钛处理TiN专业加工服务TiN HARD COATING FOR CUTTING TOOLS AND PUNCH BY PVD222 高中低周波感应加热炉HIGHMEDIUMLOW FREQUENCY INDUCTION HEATER223 各式螺丝类产品自动包装AUTOMATIC PACKAGING FOR ALL KINDS OF PACKAGING224 攻牙机TAPPING MACHINE225 滚牙轮THREAD ROLLING DIES226 合金钢线材盘元ALLOY STEEL WIRE ROD227 黑铁丝BLACK WIRE228 环规、牙规、三线规校正CALIBRATION FOR RING GAGE ATHREAD GAGE 3 WIRE GAGE229 环规校正CALIBRATION FOR RING GAGE230 黄铜棒线BRASS WIRE AND ROD231 机踏车用螺丝成型机SCREW FOR MOTORCYCLE OR BICYCLE HEADING MACHINE232 机械镀锌MECHANICAL GALVANIZED233 鸡眼上下模EYELETS DIES234 精抽自动收线机NON-STOP COILERSKINPASS235 精密油压滚牙机HYDRAULIC THREAD ROLLING MACHINES236 空心打头机HOLLOW HEADING MACHINE237 快削钢线材盘元FREE CUTTING STEEL WIRE ROD238 拉钉打头机BLIND RIVET HEADING MACHINE239 连续式光辉调质淬火炉CONTINUOUS BRIGHT HARDENING QUENCHING FURNACE240 连续式光辉热处理炉CONTINUOUS TYPE BRIGHT HEAT TREATMENT FURNACE 5/7241 连续式光辉渗碳淬火炉CONTINUOUS BRIGHT CARBURIZING QUENCHING FURNACE NABS-全球紧固件配套服务公司242 磷青铜线PHOSPHATE BRONZE WIRE243 六角整头模TRIMMING DIES HEXAGAN244 螺帽成型模NUTS FORMERS245 螺帽模NUT FORMING DIES246 螺丝、螺帽成型攻牙专用油FORMING AND TAPPING OILS FOR BOLTS AND NUTS FORMERS247 螺丝、螺帽成型机BOLT FORMERSNUTS FORMERSHEADERS248 螺丝、螺帽品检量测仪器FASTENERS INSPECTION AND MEASUREMENT INSTRUMENTS249 螺丝、螺帽热处理BOLT NUT AND SCREWS HEAT TREATMENT250 螺丝、螺帽热处理炉BOLT NUT AND SCREWS HEAT TREATMENT FURNACES251 螺丝、螺帽五金等检验INSPTECTION SERVICES FOR FASTENERS AND HARDWARE252 螺丝打头机HEADING MACHINE253 螺丝割尾及特殊割遘加工MACHINE SCREW SHANK SLOTTING254 螺丝割尾加工机械AUTOMATIC THREAD SLOTTING MACHINE255 螺丝攻、车刀、模具TAPS DIES AND TOOLS256 螺丝制造成型机械AUTOMATIC TRIMMING MACHINE257 螺丝制造搓牙机械AUTOMATIC THREAD ROLLING MACHINE258 螺丝制造高速搓牙机械HIGH SPEED AUTOMATIC THREAD ROLLING MACHINE259 螺丝钻孔加工SCREW SHANK DRILLING260 罗拉成型机ROLLERS FORMERS261 迷你成型机MINI-FORMERS262 模具TOOLS263 磨光棒钢BRIGHT STEELBARHEX/ROUND/SQUARE264 气动拉钉机AIR RIVETER265 球状化电器炖炉CARBURIZING FURNACE VACUUM AND BELL TYPE FURNACE266 球状化热处理炉SPHEROIDIZING HEAT TREATMENT FURNACE267 球状化线材ANNEALING WIRE AND ROD268 热浸镀锌螺丝、螺帽HOT DIP GALVANIZING BOLTS AND NUTS269 生产管理系统PRODUCTION CONTROL SYSTEM270 十字冲模HEADER PUNCHES IN VARIOUS DRIVES271 碳化钨模具TUNGSTEN CARBIDE DIE272 套高成型机SOCKETS FORMERS273 特殊零件成型机PARTSFORMING MACHING274 铜合金线COPPER ALLOY WIRE275 物料管理系统MATERIAL CONTROL SYSTEM276 线材IRON OR STEEL WIRE277 线材盘元IRON OR STEEL WIRE ROD278 线切割线E.D.M CUTTING WIRE279 牙板THREAD ROLLING DIES PLATES280 洋白铜线NICKEL SILVER WIRE281 一般线材、盘元、螺丝合金炖炉SPHEROIDIZING BRIGHT ANNEALING FURNACE282 一般线材、盘元、退火炉GENERAL WIREWIRE RODANNEALING FURNACE283 止付螺丝成型机SET SCREWS FORMERS284 中、高热镀锌光辉连续炉CONTINUOUS BRIGHT HEAT TREAT FURNACE285 转回90 度碾线头机90 REVOLVING WIRE TWISTING MACHINE286 自动包装机AUTOMATIC PACKING MACHINE 6/7NABS-全球紧固件配套服务公司 7/7。
紧固件中英文对照表(Terminology for fastener)
非金属嵌件六角锁紧螺母Prevailing torque type hexagon nuts(with non-metallic insert)六角开槽螺母Hexagon slotted nuts六角开槽螺母细牙Hexagon slotted and castle nuts-Fine pitch thread六角螺母Hexagon nuts六角螺母－细牙Hexagon nuts-Fine pitch thread全金属六角锁紧螺母Prevailing torque type all-metal hexagon nuts120度半沉头铆钉120degree oval countersunk rivets120度沉头半空心铆钉120 degree countersunk head semi-tubular rivets120度沉头铆钉120 degree countersunk head rivetsT形槽用螺栓Bolts for T-Slot鞍形弹簧垫圈Curved single coil spring lock washers鞍形弹性垫圈Curved spring washers半圆头带榫螺栓Cup head nib bolts半圆头低方颈螺栓Cup square neck bolts with short neck半圆头方颈螺栓Cup head square neck bolts半圆头铆钉Round head rivets扁平头铆钉Thin head rivets扁圆头半空心铆钉Oval head semi-tubular rivets扁圆头铆钉Flat round head rivets标牌铆钉Rivets for name plate标准型弹簧垫圈Single coil spring lock washers, Normal type波形弹簧垫圈Wave single coil spring lock washers波形弹性垫圈Wave spring washers槽钢用方斜垫圈Square taper washers for slot section槽销Grooved pins侧面带孔圆螺母Round nuts with set pin holes in side沉头半空心铆钉Countersunk head semi-tublar rivets沉头带榫螺栓Flat countersunk nib bolts沉头方颈螺栓Flat countersunk square neck bolts沉头铆钉Countersunk head rivets沉头双榫螺栓Flat countersunk double nib bolts大半圆头带榫螺栓Cup head nib bolts with large head大半圆头方颈螺栓Cup head square neck bolts with large head大扁圆头半空心铆钉Truss head semi-tubuar rivets大扁圆头铆钉Truss head rivets带槽圆螺母Slotted round nuts带孔销Pins with split pin hole带锁圈的螺钉锁紧挡圈Lock rings with screw and circlip单耳止动垫圈Tab washers with log tab弹性圆柱销Spring-type straight pins-Slotted等长双头螺柱Double end studs地脚螺栓Eyelet bolts吊环螺钉Eyebolts蝶形螺母Wing nuts端面带孔圆螺母Round nuts with drilled holes in one face方螺母Square nuts方头凹端紧定螺钉Square set screws with cup point方头长圆柱端紧定螺钉Square set screws with long dog point方头长圆柱球面端紧定螺钉Square set screws with long dog point and rounded end方头倒角端紧定螺钉Square set screws with chamfered end方头短圆柱锥端紧定螺钉Square set screws with short dog point and cone end非金属嵌件六角法兰面锁紧螺母Prevailing torque type hexagon nuts with flange (with non-metallic insert)封闭型扁圆头抽芯铆钉Mushroom head break mandrel closed end blind rivets封闭型沉头抽芯铆钉120 deg flush head break mandrel closed end blind rivets盖形螺母Acorn nuts工字钢用方斜垫圈Square taper washers for I section管状铆钉Pope type rivets滚花薄螺母Knurled nuts滚花高螺母Knurled nut with collar滚花高头螺钉Knurled thumb screws滚花头不脱出螺钉Knurled thumb screws with waisted shank滚花小头螺钉Knurled screws with small head焊接方螺母Square weld nuts焊接六角螺母Hexagon weld nuts环形螺母Lifting nuts活节螺栓Eye bolts机动弧焊用焊接螺柱Weld studs for are welding夹紧挡圈Grip rings开槽半沉头不脱出螺钉Slotted raised countersunk head screws with waisted shank开槽半沉头螺钉Slotted raised countersunk head screws开槽半沉头自攻螺钉Slotted raised countersunk head tapping screws开槽长圆柱端紧定螺钉Slotted set screws with long dog point开槽沉头不脱出螺钉Slotted countersunk head screws with waisted shank开槽沉头螺钉Slotted countersunk head screws开槽沉头自攻螺钉Slotted countersunk head tapping screws开槽盘头螺钉Slotted pan head screws开槽带孔球面圆柱头螺钉Slotted capstan screws开槽盘头螺钉Slotted pan head screws开槽盘头自攻螺钉Slotted pan head tapping screws开槽平端紧定螺钉Slotted set screws with flat point开槽球面大圆柱头螺钉Slotted large raised cheese head screws开槽球面圆柱头轴位螺钉Slotted raised cheese head with shoulder开槽无头轴位螺钉Slotted shoulder screws开槽圆柱端定位螺钉Slotted setscrews with dog point开槽圆柱头螺钉Slotted cheese head screws开槽圆柱头轴位螺钉Slotted cheese head screws with shoulder开槽锥端定位螺钉Slotted setscrews with cone point开口挡圈“E” rings开口垫圈Washers with split开口销Split pins开口型扁圆头抽芯铆钉Mushroom head break mandrel blind rivets开口型沉头抽芯铆钉120 deg flush head break mandrel blind rivets开尾圆锥销Taper pins with split空心铆钉Tubular rivets孔用弹性挡圈Circlips for holes孔用钢丝挡圈Roundwire snap rings for hole扣紧螺母Tight nuts六角法兰面螺母Hexagon nuts with flange六角法兰面自钻自攻螺钉Hexagon flange head self-drilling tapping screws六角头螺栓、弹簧垫圈和平垫圈组合件Hexagon head bolt, single coil spring lock washer and plain washer assemblies六角头螺栓和平垫圈组合件Hexagon head bolt and plain washer assemblies六角头螺栓和外锯齿锁紧垫圈组合件Hexagon head bolt and serrated lock washer external teeth assemblies六角头头部戴槽螺栓Hexagon bolts with slot on head六角头头部带孔螺栓Hexagon blots with wire holes on head六角头自攻螺钉Hexagon head tapping screws六角头自攻螺钉和大垫圈组合件Hexagon head tapping screw and plain washer assemblies六角头自攻锁紧螺钉Hexagon head thread forming screws六角自锁螺母Self-locking nuts, hexagon内齿锁紧垫圈Lock washers internal teeth。
紧固件中英文对照
Description in Chinese 英文品名Desciption in English圆锥销Taper pins圆柱销Parallel pins开槽圆柱头螺钉Slotted cheese head screws开槽盘头螺钉Slotted pan head screws单耳止动垫圈Tab washers开口销Split cooter pins开槽半沉头木螺钉Slotted raised csk head wood screws 开槽半圆头木螺钉Slotted round head wood screws开槽沉头木螺钉Slotted countersunk head wood screws 平垫Plain washers平垫（带倒角）Mediun washers平垫Plain washers重型弹垫Spring lock washers,tang ends标准弹垫Spring lock washers,square ends鞍形弹垫Single coil spring lock washers弹簧止动垫圈Curved spring washers波形弹垫Wave spring washersT型方颈螺栓T-head blots with square neckT型双接头螺栓T-head bolts with double nip螺纹圆锥销Taper pins with threaded endT型头螺栓T-head bolts蝶型螺母（美制）Wing nuts America form蝶型螺母（德制）Wing nuts germany form蝶型螺母（美制）Wing screws America form蝶型螺母（德制）Wing screws germany form圆球型盖型螺母Ball knobs开槽带孔球面圆柱头蚴钉Slotted capstan screws开槽长圆柱端紧定螺钉Slotted set srews with full dog point开槽平端紧定螺钉（半牙）Slotted set srews with chamfered end 小六角特薄细牙螺母Pip nuts with thread外舌止动垫圈External tap小垫圈(用于圆柱头螺钉) Washers for cheese head screws方斜垫圈（U型）Square taper washers forU-section方斜垫圈（I型）Square taper washers forI-sections方垫圈Square washers开槽凹端紧定螺钉Slotted set with cup point六角薄螺母Hexagon thin nuts细牙六角薄螺母Hexagon thin nuts木螺钉专用垫圈Rounds washers for wood constructions密封帽Sealing caps,push-in type活节螺栓B型Eye bolts form B内舌止动垫圈Internal tab washers双耳止动垫圈Washers with two taps滚花高头螺钉Knurled thumb screws with collar开槽滚花高头螺钉Slotted knurled thumb screws with collar 滚花高螺母Knurled thumb nuts with collar滚花薄螺母Knurled thumb thin nuts锁紧垫圈Sealing washers轴用弹性垫圈Retaining rings for shafts(external),circlips孔用弹性垫圈Retaining rings for bores(internal),circlips方头带垫螺栓Square head bolts with collar方头圆柱底端螺栓Square head bolts with half dog point方头带垫关圆底端螺栓Square head bolts with collar,half dog pointT型槽螺母T-slot nuts单头螺柱Single end studs地脚螺栓Masonry bolts带槽圆螺母Slotted round nuts端面带孔圆螺母Round nuts with drilled holes in one face 开槽平端紧定螺钉Slotted set screws with flat point开槽锥端紧定螺钉Slotted set screws with cone point六角螺母Hexagon nuts方螺母-C Square nuts六角头螺钉Hexagon screws六角头圆柱端紧定螺钉Hexagon set screws with full dog point薄型方螺母-B Square nuts without bevel(pressed nuts)六角头木螺钉Hexgon head wood screw(coach screws)吊环螺钉Lifting eye bolts吊环螺母Lifting eye nuts圆锥型槽销Grooved pins,taper grooved圆锥型槽销（半槽）Grooved pins,taper grooved half length平行槽销（带倒角）Grooved pins,parallel grooved full length前端凹槽槽销Grooved pins,reverve grooved half length中部凹槽槽销Grooved pins,center grooved圆头槽销Grooved pins with round head沉头槽销Grooved pins with countersunk head六角螺母棒Turnuckles(center parts),made out of hexagon bar花蓝螺栓Turnuckles with eye bolt and hook bolt弹性圆柱销Spring pins,heavy type组合式盖型螺母Hexagon domed cap nuts开槽圆螺母(配合沟头扳手) Slotted round nuts for hook spammer圆螺母（带插销孔）Round nuts with set holes盘型弹簧垫圈Disc springs喉箍Hose clamps润滑油嘴（旋扭头）Lubricating nipples,button head管夹Shackles for conduiltsU型螺栓Stirrup bolts(U-bolts)球面垫圈Spherical washers,conical seats圆柱销Parallel pins厚六角螺母Hexagon nuts,1.5d厚六角法兰面螺母Hexagon nuts,1.5d with collar长六角螺母Hexagon nuts,3d外齿锁紧垫圈External teeth lock washers内齿锁紧垫圈Internal teeth lock washers外锯齿锁紧垫圈External teeth serrated lock washers内锯齿锁紧垫圈Internal teeth serrated lock washers开口挡圈Retaining rings for shafts(E-rings),circlips平键（A型）Parallel keys(form A)半圆键Woodruff keys嵌环（支撑环）Thimbles机器螺钉和垫圈组合件Screws and washers assemblies自攻螺钉和垫圈组合件Tapping screws and washer assemblies薄型带孔内六角圆柱螺钉Hexagon cocket head cap screws with hole,low head大六角头螺栓Hexagon head bolts with large head(friction grip nolts)大六角螺母Hexagon nuts with large wideth across flat(friction grip nuts)大垫圈Round washers for friction grip bolts楔型方垫圈Spuare taper washers for friction grip bolts on T-六角法兰面螺母Hexagon flange nuts全金属六角锁紧螺母（2型）Prevailing torque type hexagon nuts,all metallic nuts 轻型弹性圆柱销Spring pins,light type重型弹性圆柱销用垫圈Washers for bolts with heavy type spring pinssISO公制螺纹螺钉（多种头型）Thread forming screws for ISO-metric thread 自攻自钻螺钉（多种头型）Self-drilling tapping screws开槽切削螺纹螺钉（多种头型）Thread cutting screws十字槽切削螺纹螺钉（多种头型）Thread cutting screws cross recessT型四爪螺母Tee nuts with pronge钢结构用六角头螺栓连接副Hexagon head fitted bolts for steel structures开槽盘头自攻螺钉Pan head tapping screws with slot开槽沉头自攻螺钉countersunk flat head tapping screws with slot开槽半沉头自攻螺钉Raised sountersunk oval head tapping screws with slot六角头自攻螺钉Hexagon tapping screws圆柱头螺钉用弹簧垫圈Spring lock washers for screws with cylindrical heads十字槽盘头自攻螺攻Pan head tapping screws with cross recessed十字槽沉头自攻螺攻Countersunk flat head tapping screws with cross recessed十字槽半沉头自攻螺攻Raised countersunk oval head tapping screws with cross薄型内六角圆柱头螺钉Hexagon socket head cap screws with,reduced head十字槽盘头螺钉Pan head screws with cross recessed钢结构用垫圈Washers for steel structures钢结构用六角头螺栓Hexagon head bolts for steel structures内六角沉头螺钉Hexagon socket coutersunk head screws轴用钢丝挡圈Roundwire snap rings for shafts十字槽半沉头木螺钉Cross recessed raised countersunk head wood screws十字槽圆头木螺钉Cross recessed round head wood screws十字槽沉头木螺钉Cross recessed countersunk head wood screws螺纹护套(普通、自锁等) Ciol inserts,coarse,fine thread,silf locking大外径垫圈Washers,outside diameter appro.3d弹簧卡子sping cotter for a bolt平板螺栓Belting bolts(elevator bolts)干壁钉（墙板钉）Dry wall screws环型螺母Lifting nuts(eye nuts)圆螺母用止退垫圈Tab washer for slotted round nuts。
螺母种类（英文注释）
本文版权所属标准件之都网，如需转载、摘编或以其它方式使用本文内容，请在授权范围内使用，并标注“来源：标准件之都”
本文版权所属标准件之都网如需转载摘编或以其它方式使用本文内容请在授权范围内使用并标注来源
螺母种类（英文注释）
螺母（Nut）
一、六角螺母（Finished Hex Nut---FHN）
二、重型六角螺母（Heavy Hex Nut）
三、六角开槽螺母（Slotted Hex Nut）
四、皇冠螺母（Hex Castle Nut）
五、盖形螺母（Acorn Nut）
六、蝶形螺母（Wing Nut）
七、方形螺母（Square Nut）
八、齿形螺母（K-Lock Nut / Keps Nut）
九、六角薄螺母（Hex Jam Nut）
十、法兰螺母（Serrated Hex Flange Nut）
十一、尼龙
简体中文版-螺丝产品名称中英文对照
六角螺絲(栓) HEX HEAD CAP SCREWS(HEX BOLTS)六角机械螺丝HEX HEAD MACHINE BOLTS六角木牙螺丝HEX LAG BOLTS四角螺絲SQUARE HEAD BOLTST头螺絲T HEAD BOLTS马车螺絲CARRIAGE BOLTS环首螺絲EYE BOLTS內六角孔螺絲HEX SOCKET CAP SCREWS固定螺絲SET SCREWS螺椿栓STUD BOLTS螺旋椿SCREW STUDS轮毂螺栓WHEEL BOLTS翼形螺絲WING SCREWS自攻螺絲SELF TAPPING SCREWS自削螺絲THREAD CUTTING SCREWS鐟尾螺絲SELF DRILLING SCREWS旋入螺絲DRIVE SCREWS机械螺絲MACHINE SCREWS木螺絲WOOD SCREWS家具螺絲FURNITURE SCREWS塑板螺絲CHIPBOARD SCREWS墙用螺絲DRYWALL SCREWS基楚螺栓FOUNDATION BOLTSU型螺栓U BOLTS勾头螺栓HOOK BOLTS套掛螺絲TOGGLE BOLTS突緣螺絲FLANGE BOLTS轨道螺栓(魚尾螺絲) TRACK BOLTS耐候钢螺絲CORTEN STEEL HEA VY HEX BOLTS扭矩控制螺栓T.C.BOLTS高張力螺栓HIGH STRENGTH BOLTS剪力釘(焊接螺絲) WELDING STUDS螺絲附华司組合SCREWS AND WASHERS ASSEMBLED(SEMS) 大尺寸螺栓BIG SIZE BOLTS不锈钢小螺絲STAINLESS STEEL SHEET METAL SCREWS不锈钢大螺絲STAINLESS STEEL BOLTS铜螺絲BRASS SCREWS鋁螺絲ALUMINUM SCREWS合金钢螺絲ALLOY STEEL SCREWS电子螺絲ELECTRONIC SCREWS微小精密螺絲MICRO SCREWS塑胶螺絲PLASTIC SCREWS复合材料用螺絲PARTICLE BOARD SCREWS鈦合金螺絲TITANIUM ALLOY BOLTS鈦、鋯、鉬、鈮等螺絲、零件、材料TI,ZR,MO,NB PARE METAL BOLTS PARTS拇指螺絲THUMB SCREWS雙头牙螺絲DOUBLE END SCREWS HANGER BOLT车辆(汽车)螺絲、螺帽AUTOMOTIVE FASTENERS航太用螺絲AEROSPACE FASTENERS飛机械特殊扣件SOURCE CONTROL BOLTS拉栓BLIND BOLTS面板螺絲PANEL FASTENERS电梯螺絲ELEVATOR BOLTS四角头固定螺絲SQUARE SET SCREWS大头马车螺絲STEP BOLTS单向螺絲ONE WAY LAG SCREWS管夹螺絲HOSE CLAMP SCREWS不锈钢固定螺絲STAINLESS STEEL HEX SOCKET CAP SCREWS不锈钢內六角螺絲STAINLESS STEEL HEX SOCKET CAP SCREWS铰链螺絲HINGE SCREWS货柜螺絲CONTAINER SCREWS复合材料鐟尾螺絲BI-METAL SELF DRILLING SCREWS三角牙螺絲TRILOBULAR THREAD SCREWS高低牙螺絲HIGH LOW SCREWS夹板用螺絲PARTICLE BOARD SCREWS马桶螺絲TOILET CLOSET BOLTS特長螺絲SPECIAL LONGER SCREWS建業螺絲BUILDING FASTENERS不锈钢六角螺絲STAINLESS STEEL HEX SOCKET CAP SCREWS其它特殊螺絲SPECIAL SCREWS OR BOLTS不锈钢特殊螺絲SPECIAL STAINLESS STEEL SCREWS寬牙螺絲（粗牙螺絲）COARSE THREAD SCREWS链帶螺絲COLLATED SCREWS水泥螺絲CONCRETE SCREWS板模螺絲CONSTRUCTION BOLTS锌蝶螺絲DIE CAST WING SCREWS; ZINC ALLOY重型车螺絲HEA VY DUTY WHEEL HUB BOLTS內六角固定螺絲HEX SOCKET SET SCREWS复合材料用螺絲（夹板用）PARTICLE BOARD SCREWS犁壁螺絲PLOW BOLTS机械(踏)车用螺絲、轴心SCREWS AND SHAFTS FOR MOTORCYCLE OR BICYCLE 针车用螺絲、轴心SCREWS AND SHAFTS FOR SEWING MACHING止付螺絲SOCKET SET SCREWS不锈钢寬牙螺絲STAINLESS STEEL COARSE THREAD SCREWS不锈钢高低牙螺絲STAINLESS STEEL HIGH-LOW THREAD SCREWS不锈钢机械螺絲STAINLESS STEEL MACHINE SCREWS不锈钢鐟尾螺絲STAINLESS STEEL SELF DRILLING SCREWS不锈钢自攻螺絲STAINLESS STEEL SELF TAPPING SCREWS不锈钢自削螺絲STAINLESS STEEL THREAD CUTTING SCREWS不锈钢三角牙螺絲STAINLESS STEEL TRI-LOBULAR THREAD SCREWS 不锈钢木螺絲STAINLESS STEEL WOOD SCREWS套掛螺栓及螺絲TOGGLE BOLTS鈦合金膨胀螺絲TITANIUM ALLOY EXPANSION BOLTS螺帽类六角盖头螺帽HEX CAP NUTS六角锯齿螺帽HEX SERRATED NUTS六角轮緣螺帽HEX FLANGE NUTS高腳螺帽HEX COUPLING NUTS(HIGH NUTS)圓螺帽ROUND NUTS四角螺帽SQUARE NUTS管用螺帽PIPE NUTS轮毂螺帽WHEEL NUTS蝶型螺帽WING NUTSU形螺帽U NUTST形螺帽T NUTS环首螺帽EYE NUTS齿形螺帽KEP NUTS齿花螺帽CLINCH NUTS耐候钢六角重型螺帽CORTEN STEEL HEA VY HEX NUTS焊接螺帽WELD NUTS高張力螺帽HEIGH STRENGTH NUTS建業用螺帽STRUCTURAL NUTS不锈钢螺帽STAINLESS STEEL NUTS铜螺帽BRASS NUTS鋁螺帽ALUMINUM NUTS合金钢螺帽ALLOY STEEL NUTS重型车螺帽HEA VY DUTY WHEEL HUB NUTS铁器焊接袋帽ACORN CAP NUTS金属预置扭矩式螺帽ALL-METAL PREVAILING TORQUE TYPE NUTS壁虎螺帽ANCHOR NUTS大尺寸螺帽BIG SIZE NUTS铁盖袋帽CLOSED END ACORN NUTS盘形华司螺帽CONICAL WASHER NUTS铁盖+尼龙圈組合盖帽DIN 986 DOMED CAP NUTS突緣尼龙盖帽FLANGE NYLON INSERT LOCK NUTS平面华司螺帽FLAT WASER NUTS六角割溝螺帽HEX SLOTTED NUT自锁螺帽SELF-LOCKING NUTS制止螺帽SLIDING NUTSSLN-自动防松螺帽SLN SELF-LOCKING NUTS其它特殊螺帽SPECIAL NUTS弹簧螺帽SPRING NUTS不锈钢突緣螺帽STAINLESS STEEL FLANGE NUTS不锈钢六角轮緣尼龙螺帽STAINLESS STEEL FLANGE NYLON INSERT LOCK NUTS不锈钢六角重型螺帽STAINLESS STEEL HEA VY HEX NUTS不锈钢六角螺帽STAINLESS STEEL HEX NUTS不锈钢尼龙嵌入螺帽STAINLESS STEEL NYLON INSERT LOCK NUTS锌压属螺帽ZINC DIE CASTING NUTS普通六角螺帽HEX NUTS六角重型螺帽HEA VY HEX NUTS薄型螺帽HEX JAM NUTS尼龙嵌入防松螺帽NYLON INSERT LOCK NUTS机械螺絲用六角螺帽HEX MACHINE SCREW NUT线材类合金钢线材盘元ALLOY STEEL WIRE ROD球狀化线材ANNEALING WIRE AND ROD黑铁絲BLACK WIRE黃铜棒线BRASS WIRE AND ROD磨光棒钢BRIGHT STEEL BAR(HEX/ROUND/SQUARE)铜合金线COPPER ALLOY WIRE线切割线 E.D.M CUTTING WIRE快削钢线材盘元FREE CUTTING STEEL WIRE ROD线材IRON OR STEEL WIRE线材盘元IRON OR STEEL WIRE ROD洋白铜线NICKEL SILVER WIRE磷青铜线PHOSPHATE BRONZE WIRE不锈钢条棒STAINLESS STEEL BAR(ROUND/HEX/SQUARE)不锈钢冷鍛线材STAINLESS STEEL COLD HEADING WIRE不锈钢线(抽线後) STAINLESS STEEL DRAW WIRE不锈钢线材STAINLESS STEEL WIRE不锈钢线材及盘元STAINLESS STEEL WIRE AND ROD设备类棒钢STEEL BAR(HEX/ROUND/SQUARE)转回90度碾线头机械90訌EVOLVING WIRE TWISTING MACHINE气动拉釘机械AIR RIVETER各式螺絲類產品自动包装AUTOMATIC PACKAGING FOR ALL KINDS OF PACKAGING 自动包装机械AUTOMATIC PACKING MACHINE螺絲制造搓牙机械AUTOMATIC THREAD ROLLING MACHINE螺絲割尾加工机械AUTOMATIC THREAD SLOTTING MACHINE螺絲制造成型机械AUTOMATIC TRIMMING MACHINE拉釘打头机械BLIND RIVET HEADING MACHINE螺絲、螺帽成型机械BOLT FORMERS,NUTS FORMERS,HEADERS螺絲、螺帽热处理BOLT NUT AND SCREWS HEAT TREA TMENT螺絲、螺帽热处理爐BOLT NUT AND SCREWS HEAT TREA TMENT FURNACES球狀化电器燉爐CARBURIZING FURNACE VACUUM AND BELL TYPE FURNACE超防銹复合瓷膜CERAMIC COATING连续式光輝滲碳淬火爐CONTINUOUS BRIGHT CARBURIZING QUENCHING FURNACE连续式光輝?#123;質淬火爐CONTINUOUS BRIGHT HARDENING QUENCHING FURNACE 中、高热镀锌光輝连续爐CONTINUOUS BRIGHT HEAT TREA T FURNACE连续式光輝热处理爐CONTINUOUS TYPE BRIGHT HEAT TREA TMENT FURNACE螺絲割尾及特殊割遘加工MACHINE SCREW SHANK SLOTTING螺絲鐟孔加工SCREW SHANK DRILLING鸡眼上下模EYELETS DIES一般线材、盘元、退火爐GENERAL WIRE,WIRE ROD,ANNEALING FURNACE倒立式滑落型伸线机械HANDSTAND TYPE WIRE DRAWING MACHINE十字沖模HEADER PUNCHES IN VARIOUS DRIVES成型沖模HEADER PUNCHES IN VARIOUS DRIVES螺絲打头机械HEADING MACHINE螺絲制造高速搓牙机械HIGH SPEED AUTOMATIC THREAD ROLLING MACHINE高中低周波感應加热爐HIGH,MEDIUM,LOW FREQUENCY INDUCTION HEA TER空心打头机械HOLLOW HEADING MACHINE热浸镀锌螺絲、螺帽HOT DIP GALVANIZING BOLTS AND NUTS机械镀锌MECHANICAL GALVANIZED迷你成型机械MINI-FORMERS成品自动收线机械NON-STOP COILER精抽自动收线机械NON-STOP COILER(SKINPASS)螺帽模NUT FORMING DIES螺帽成型模NUTS FORMERS特殊零件成型机械PARTS FORMING MACHING沖模PUNCH DIES沖子PUNCH PINS罗拉成型机械ROLLERS FORMERS机械(踏)车用螺絲成型机械SCREW FOR MOTORCYCLE OR BICYCLE HEADING MACHINE 止付螺絲成型机械SET SCREWS FORMERS套高成型机械SOCKETS FORMERS一般线材、盘元、螺絲合金燉爐SPHEROIDIZING BRIGHT ANNEALING FURNACE球狀化热处理爐SPHEROIDIZING HEAT TREATMENT FURNACE攻牙机械TAPPING MACHINE螺絲攻、车刀、模具TAPS DIES AND TOOLS搓牙机械铁屑分離装置THREAD CHIP SEPARATOR滾牙轮THREAD ROLLING DIES牙板THREAD ROLLING DIES PLATES精密油压滾牙机械HYDRAULIC THREAD ROLLING MACHINES模具TOOLS六角整头模TRIMMING DIES HEXAGAN碳化鎢模具TUNGSTEN CARBIDE DIE镀鈦处理(TiN)专業加工服務TiN HARD COATING FOR CUTTING TOOLS AND PUNCH BY PVD电镀化学原料VARIOUS ELECTROPLATING CHEMICALS环规校正CALIBRATION FOR RING GAGE环规、牙规、三线规校正CALIBRATION FOR RING GAGE, A THREAD GAGE, 3 WIRE GAGE 螺絲、螺帽品檢量測儀器FASTENERS INSPECTION AND MEASUREMENT INSTRUMENTS 螺絲、螺帽成型攻牙专用油FORMING AND TAPPING OILS FOR BOLTS AND NUTS FORMERS 螺絲、螺帽五金等檢驗INSPTECTION SERVICES FOR FASTENERS AND HARDWAREISO品質保證系統ISO QUALITY ASSURANCE SYSTEM生產管理系統PRODUCTION CONTROL SYSTEM物料管理系統MATERIAL CONTROL SYSTEM其它齿轮GEARS不銹钢牙条棒STAINLESS STEEL HREAD ROD马达轴承轴心組件BEARING SHAFT(MOTOR)轴承轴心BEARING SHAFT开口鉚釘BLIND RIVETS長形拉帽BLIND RIVET NUTS拉帽BLIND NUTS拉釘BLIND RIVETS实心梢CLEVIS PINS AND STRAIGHT PINS弹片CLIPS卷釘COIL NAILS冷鍛零件COLD FORMING PART开口销COTTER PINSE型环E-RINGS膨胀螺栓EXPANSION ANCHOR BOLTS鸡眼釘EYELETS RIVETSR型销SNAP PINS閘、锁LATCHES AND KEEPER ASSEMBLEDS其它特殊鉚釘OTHER SPECIL RIVETS销PINS格式管夹、管束PIPE HANGER鉚釘RIVETS螺旋鋦及螺旋圈SCREW HOOK AND SCREW RINGS中空釘SEMI-TUBULAR RIVET开叉釘SPLIT DRIVE ANCHORS弹簧华司SPRING WASHERS弹簧蝴蝶夹SPRING WINGS不銹钢华司STAINLESSSTEEL WASHERS钢铁釘STEEL AND IRON NAILS搓牙铁釘THREAD NAILS鈦合金鉚釘TITAIUM ALLOY RIVETS管形鉚釘TUBULAR RIVETS华司WASHERS真空热处理VACUUM HEAT TREATMENT螺絲、螺帽、五金、DIY扣件FASTENERS合金钢工具ALLOY STEEL TOOLS螺栓模BOLT HEADING DIES手动拉釘鉗HAND RIVETER船舶链ANCHOR CHAIN腳踏车链锁BICYCLE CHAIN LOCKS螺絲起子BIT罗拉CHAIN ROLLER特殊鉚合扣件COLLARS(A BLINDFASTENER FOR HUCK INTL)装饰链DECORATIVE CHAINS自攻螺紋襯套ENSAT THREADED INSERTS六角扳手HEXAGON KEYS超音螺紋压入式螺紋自动锁扣THREADED INSERTS FOR PLASTIC INJECTION MOULDEINGS汽车特殊桿接件SPECIAL AUTO-MOBILE FASTENER AS YOUR NEEDS螺紋護套RECOIL INSERTS链条用滾子ROLLER FOR ROLLER CHAIN金属板鑲嵌組件及自动夹扣組件SHEET METAL FASTENERS工具套筒組件SOCKET WRENCH SETS不銹钢链STAINLESS STEEL CHAINS軛子T-YOKE轮胎链TIRE CHAINS狗链DOG CHAINS喇叭头軛铁U-YOKE,T-YOKE FOR SPEAKER不銹钢輸送帶轮用轨道STAINLESS WHEEL'S RACK FOR TRANSPORTER工業用链INDUSTRIAL STEEL LINK CHAINS拖链安全链TOW CHAINS AND SAFETY CHAINS机械车離合器零件MANUFACTURE OF MOTORCYCLE'S CVT PARTS牙条棒THREAD ROD螺纹大径：Major Diam螺纹中径：Pitch diam螺纹底径：Minor diam通止规：Go/No go gage机械性能：mechanical and physical propertiesunified thread 统一英制螺纹Lustrate hydrogen after galvanizing to avoid hydrogen embrittlement 镀后去氢，防止氢脆Case carburization 表面渗碳With across flats 对边With across corners 对角Radius of fillet:头下圆角Transition thread length 过度螺纹Wrenching height 扳拧高度Rockwell 铬氏硬度Vickers 维氏硬度Brinell 布氏硬度Metallography microscope 金相显微镜Salt spray device 盐雾试验箱Tensile testing machine 拉力试验机Cold forming 冷打Hot forging 红镦P C 8 = property class 8 机械性能8级原材料：Raw material球化退火：Annealing冷拔：Drawing冷镦：Forming机加工：Machining螺纹成型：Roll Threading热处理：heat-treatment表面处理：finish去氢：Lustrating hydrogen检验：Inspection包装：Packing入库：Stocking车床：lathe磨制：grinding红打：hot forging冲压：punchingDiameter 直径Length 长度1 标准GB （国家标准）ISO(国际标准) DIN （德制）JIS （日标）ANSI /ASME （美标）BA （英制）2 螺纹M. MF (公制牙)UNC.UNF (美制牙)BSW.BSF (英制牙)3 海关编码73181500 螺栓73181600 螺帽73182100 垫圈BO=black oxide 氧化发黑IHH=ind hex head 锯六角头PH=phillips 十字槽sw/fw=split washer/flatwasher 弹垫平垫kep nut 锁紧螺母cementation 渗碳acorn nut 盖形螺母头型类Pan 圆头(盘头)Oval 半沉头H.W.H.. 六角小法兰H.W.F. 六角大法兰CSK 沙拉头(沉头)Large wafer 大扁平头Bugle 喇叭头Truss 盘头带垫Pozi 米制槽Phill 十字槽Serra-tion 垫下带花Flower Head 开花头6-bobes recess 内梅花Piston bolt 活塞螺钉Winding bolt 线圈螺钉Hexagon head bolts-full thread 六角头螺栓全螺纹Carriage bolt 马车螺栓Square head bolt-product grade C 方头螺栓C级Flat counter sunk square neck bolts 沉头方颈螺栓Flat counter sunk nib bolts 沉头带榫螺栓Cup head square neck bolts 半圆头方螺栓Cup head nib bolts 半圆头带榫螺栓Cup head square neck bolts with large head –product grade C大半圆头方颈螺栓C级Hexagon head bolts-product grade C六角头螺栓C级Hexagon head bolts-full thread –product grade C 六角头螺栓全螺纹C级Hexagon head bolts 六角头螺栓Hexagon head bolts –full thread 六角头螺栓全螺纹Hexagon head bolts-reduced shank-product grade B六角头螺栓细杆菌B级Hexagon head bolts with fine pitch thread 六角头螺栓细牙Hexagon head bolts with fine pitch thread full thread六角头螺栓细牙全螺纹Hexagon flange bolts –heavy series-product grade B 六角法兰面螺栓加大系列车员B级Cross recessed pan head tapping screws 十字槽盘头自攻螺钉Hexagon flange drilling screw with tapping screw thread 六角法兰面自钻自攻螺钉螺纹大径：Major Diam螺纹中径：Pitch diam螺纹底径：Minor diam通止规：Go/No go gage机械性能：mechanical and physical propertiesunified thread 统一英制螺纹Lustrate hydrogen after galvanizing to avoid hydrogen embrittlement 镀后去氢，防止氢脆Case carburization 表面渗碳With across flats 对边With across corners 对角Radius of fillet:头下圆角Transition thread length 过度螺纹Wrenching height 扳拧高度Rockwell 铬氏硬度Vickers 维氏硬度Brinell 布氏硬度Metallography microscope 金相显微镜Salt spray device 盐雾试验箱Tensile testing machine 拉力试验机Cold forming 冷打Hot forging 红镦P C 8 = property class 8 机械性能8级合金钢线材盘元ALLOY STEEL WIRE ROD球狀化线材ANNEALING WIRE AND ROD黑铁絲BLACK WIRE黃铜棒线BRASS WIRE AND ROD磨光棒钢BRIGHT STEEL BAR(HEX/ROUND/SQUARE)铜合金线COPPER ALLOY WIRE线切割线 E.D.M CUTTING WIRE快削钢线材盘元FREE CUTTING STEEL WIRE ROD线材IRON OR STEEL WIRE线材盘元IRON OR STEEL WIRE ROD洋白铜线NICKEL SILVER WIRE磷青铜线PHOSPHATE BRONZE WIRE不锈钢条棒STAINLESS STEEL BAR(ROUND/HEX/SQUARE)不锈钢冷鍛线材STAINLESS STEEL COLD HEADING WIRE不锈钢线(抽线後) STAINLESS STEEL DRAW WIRE不锈钢线材STAINLESS STEEL WIRE不锈钢线材及盘元STAINLESS STEEL WIRE AND ROD棒钢STEEL BAR(HEX/ROUND/SQUARE)转回90度碾线头机械90訌EVOLVING WIRE TWISTING MACHINE气动拉釘机械AIR RIVETER各式螺絲類產品自动包装AUTOMATIC PACKAGING FOR ALL KINDS OF PACKAGING自动包装机械AUTOMATIC PACKING MACHINE螺絲制造搓牙机械AUTOMATIC THREAD ROLLING MACHINE螺絲割尾加工机械AUTOMATIC THREAD SLOTTING MACHINE螺絲制造成型机械AUTOMATIC TRIMMING MACHINE拉釘打头机械BLIND RIVET HEADING MACHINE螺絲、螺帽成型机械BOLT FORMERS,NUTS FORMERS,HEADERS螺絲、螺帽热处理BOLT NUT AND SCREWS HEAT TREA TMENT螺絲、螺帽热处理爐BOLT NUT AND SCREWS HEAT TREA TMENT FURNACES球狀化电器燉爐CARBURIZING FURNACE VACUUM AND BELL TYPE FURNACE超防銹复合瓷膜CERAMIC COATING连续式光輝滲碳淬火爐CONTINUOUS BRIGHT CARBURIZING QUENCHING FURNACE连续式光輝?#123;質淬火爐CONTINUOUS BRIGHT HARDENING QUENCHING FURNACE 中、高热镀锌光輝连续爐CONTINUOUS BRIGHT HEAT TREA T FURNACE连续式光輝热处理爐CONTINUOUS TYPE BRIGHT HEAT TREA TMENT FURNACE螺絲割尾及特殊割遘加工MACHINE SCREW SHANK SLOTTING螺絲鐟孔加工SCREW SHANK DRILLING鸡眼上下模EYELETS DIES一般线材、盘元、退火爐GENERAL WIRE,WIRE ROD,ANNEALING FURNACE倒立式滑落型伸线机械HANDSTAND TYPE WIRE DRAWING MACHINE十字沖模HEADER PUNCHES IN VARIOUS DRIVES成型沖模HEADER PUNCHES IN VARIOUS DRIVES螺絲打头机械HEADING MACHINE螺絲制造高速搓牙机械HIGH SPEED AUTOMATIC THREAD ROLLING MACHINE高中低周波感應加热爐HIGH,MEDIUM,LOW FREQUENCY INDUCTION HEATER空心打头机械HOLLOW HEADING MACHINE热浸镀锌螺絲、螺帽HOT DIP GALVANIZING BOLTS AND NUTS机械镀锌MECHANICAL GALVANIZED迷你成型机械MINI-FORMERS成品自动收线机械NON-STOP COILER精抽自动收线机械NON-STOP COILER(SKINPASS)螺帽模NUT FORMING DIES螺帽成型模NUTS FORMERS特殊零件成型机械PARTS FORMING MACHING沖模PUNCH DIES沖子PUNCH PINS罗拉成型机械ROLLERS FORMERS机械(踏)车用螺絲成型机械SCREW FOR MOTORCYCLE OR BICYCLE HEADING MACHINE 止付螺絲成型机械SET SCREWS FORMERS套高成型机械SOCKETS FORMERS一般线材、盘元、螺絲合金燉爐SPHEROIDIZING BRIGHT ANNEALING FURNACE球狀化热处理爐SPHEROIDIZING HEAT TREATMENT FURNACE攻牙机械TAPPING MACHINE螺絲攻、车刀、模具TAPS DIES AND TOOLS搓牙机械铁屑分離装置THREAD CHIP SEPARATOR滾牙轮THREAD ROLLING DIES牙板THREAD ROLLING DIES PLATES精密油压滾牙机械HYDRAULIC THREAD ROLLING MACHINES模具TOOLS六角整头模TRIMMING DIES HEXAGAN碳化鎢模具TUNGSTEN CARBIDE DIE镀鈦处理(TiN)专業加工服務TiN HARD COATING FOR CUTTING TOOLS AND PUNCH BY PVD电镀化学原料VARIOUS ELECTROPLATING CHEMICALS环规校正CALIBRATION FOR RING GAGE环规、牙规、三线规校正CALIBRATION FOR RING GAGE, ATHREAD GAGE, 3 WIRE GAGE 螺絲、螺帽品檢量測儀器FASTENERS INSPECTION AND MEASUREMENT INSTRUMENTS 螺絲、螺帽成型攻牙专用油FORMING AND TAPPING OILS FOR BOLTS AND NUTS FORMERS螺絲、螺帽五金等檢驗INSPTECTION SERVICES FOR FASTENERS AND HARDWARE德國SCHATZ扭力机械代理REPRESENTATIVE OF SCHATZ TORQUE MACHINISO品質保證系統ISO QUALITY ASSURANCE SYSTEM生產管理系統PRODUCTION CONTROL SYSTEM物料管理系統MATERIAL CONTROL SYSTEM齿轮GEARS不銹钢牙条棒STAINLESS STEEL HREAD ROD马达轴承轴心組件BEARING SHAFT(MOTOR)轴承轴心BEARING SHAFT开口鉚釘BLIND RIVETS長形拉帽BLIND RIVET NUTS拉帽BLIND NUTS拉釘BLIND RIVETS实心梢CLEVIS PINS AND STRAIGHT PINS弹片CLIPS卷釘COIL NAILS冷鍛零件COLD FORMING PART开口销COTTER PINSE型环E-RINGS膨胀螺栓EXPANSION ANCHOR BOLTS鸡眼釘EYELETS RIVETSR型销SNAP PINS閘、锁LATCHES AND KEEPER ASSEMBLEDS其它特殊鉚釘OTHER SPECIL RIVETS销PINS格式管夹、管束PIPE HANGER鉚釘RIVETS螺旋鋦及螺旋圈SCREW HOOK AND SCREW RINGS中空釘SEMI-TUBULAR RIVET开叉釘SPLIT DRIVE ANCHORS弹簧华司SPRING WASHERS弹簧蝴蝶夹SPRING WINGS不銹钢华司STAINLESSSTEEL WASHERS钢铁釘STEEL AND IRON NAILS搓牙铁釘THREAD NAILS鈦合金鉚釘TITAIUM ALLOY RIVETS管形鉚釘TUBULAR RIVETS华司WASHERS真空热处理VACUUM HEAT TREATMENT螺絲、螺帽、五金、DIY扣件FASTENERS合金钢工具ALLOY STEEL TOOLS螺栓模BOLT HEADING DIES手动拉釘鉗HAND RIVETER船舶链ANCHOR CHAIN腳踏车链锁BICYCLE CHAIN LOCKS螺絲起子BIT罗拉CHAIN ROLLER特殊鉚合扣件COLLARS(A BLINDFASTENER FOR HUCK INTL)装饰链DECORATIVE CHAINS自攻螺紋襯套ENSAT THREADED INSERTS六角扳手HEXAGON KEYS超音螺紋压入式螺紋自动锁扣THREADED INSERTS FOR PLASTIC INJECTION MOULDEINGS汽车特殊桿接件SPECIAL AUTO-MOBILE FASTENER AS YOUR NEEDS螺紋護套RECOIL INSERTS链条用滾子ROLLER FOR ROLLER CHAIN金属板鑲嵌組件及自动夹扣組件SHEET METAL FASTENERS工具套筒組件SOCKET WRENCH SETS不銹钢链STAINLESS STEEL CHAINS軛子T-YOKE轮胎链TIRE CHAINS狗链DOG CHAINS喇叭头軛铁U-YOKE,T-YOKE FOR SPEAKER不銹钢輸送帶轮用轨道STAINLESS WHEELS RACK FOR TRANSPORTER工業用链INDUSTRIAL STEEL LINK CHAINS拖链安全链TOW CHAINS AND SAFETY CHAINS机械车離合器零件MANUFACTURE OF MOTORCYCLES CVT PARTS牙条棒THREAD ROD。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
DAIMLERCHRYSLER CORPORATION No: MS-6179<S>Material Standard Date Published: 2003-05-21 Category Code: X-1 Change: FEASL Req.: NoRESTRICTED: NoMETRIC SERIES STEEL NUTS公制系列钢制螺母1.0 GENERAL 总则1.1 Purpose 目的This standard describes the requirements for metric series steel nuts in four property classes, MS-6179 Classes 5, 8, 9, and 10, for use in miscellaneous automotive applications.本标准 述的是 制系列的5，8，9，10四个性能等级和MS-6179等级钢制螺母，使用于汽车的各种用途1.2 Coverage of this Standard 本标准的范围This standard covers the chemical composition, processing (forming, heat treatment), mechanical properties (methods of testing), identification and quality requirements of the finish product.本标准包括化学成分，过程 成形，热处理 ，机械特性 测试方法 ，标记和成品的质量要求1.3 Designation on Drawings 图 的指定For specification purposes on DaimlerChrysler Engineering drawings, the four property classes shall be designated as follows in Table 1.克莱斯勒 工程图 的说明，应按 面表1指定性能等级 分四个2.0 MA TERIAL CHARACTERISTICS 材料特性The steel used to fabricate these parts shall be made from steel wire, in accordance to approved commercial practices. It shall be uniform in chemistry and quality; clean, sound and free from all surface and internal defects detrimental to the fabrication, performance or appearance of the parts for which it is intended. Additional information on steel quality can be found in MS-BAR<S>.用来制造这些紧固件的钢材应按照批准的商业运作选用圆钢，它们必须有一致的化学成分，干净，坚固，没有 零件要达到的制造，性能，外 有害的所有表面和内部缺陷，钢质量的进一步要求 MS-BAR S CHEMICAL COMPOSITION 化学成分TABLE 1: DESIGNATION ON DRAWINGS表1，图 的指定Property Class Nut螺母的性能等级Suitable for use with: 适用配MS-6179<S>-5 MS-6149<S> property class 4.8 screws, bolts and studs 性能等级4.8的螺栓，螺钉，双头螺栓MS-6179<S>-8 MS-6149<S> property class 8.8 and 4.8 screws, bolts and studs性能等级4.8-8.8的螺栓，螺钉，双头螺栓MS-6179<S>-9 MS-6149<S> property class 9.8 and 4.8 screws, bolts and studs性能等级4.8-9.8的螺栓，螺钉，双头螺栓MS-6179<S>-10 MS-6149<S> property class 10.9, 9.8 and 8.8 screws, bolts and studs性能等级8.8，9.8，10.8的螺栓，螺钉，双头螺栓No exact chemical composition is specified. Selection of a steel for each nut property class shall be optional for each manufacturing source, but that steel shall be capable of meeting the requirements of Table 2.没有规定化学成分， 每种螺母的性能等级的钢的选用应由供应商自定，但钢应满足表2的要求4.0 PROCESS REQUIREMENTS 过程要求4.1 Forming 成形Nuts conforming to this standard shall be cold formed, unless otherwise specified.按本标准的螺母应 成形，除非另有说明4.2 Heat Treatment 热处理A. Property Classes MS-6179<S>-5, 8 and 9 nuts need not be heat treated. MS-6179 S 性能等级5，8，9的螺母不必热处理B. Property Class MS-6179<S>-10 nuts shall be heat treated per DaimlerChrysler Process Standard PS1<S> using an oil quenchant followed by a minimum tempering temperature of 450 degreesC.MS-6179 S 性能等级10的螺母应按克莱斯勒过程标准PS1 S 热处理，用油淬火随 最小450摄氏度回火NOTE : Case hardening for any reason shall not be permitted.说明：渗碳淬火在任何情 是不允许的5.0 PERFORMANCE REQUIREMENTS OF THE MA TERIAL 材料的性能要求5.1 Mechanical Properties and Tests机械性能的测试5.1.1 Hardness 硬度The hardness of finished nuts shall be as shown in Table 2. 成品的螺母的硬度须按表2定TABLE 2: PROOF LOAD AND HARDNESS REQUIREMENTS FOR METRIC SERIES STEEL NUTS表2. 制系列钢制螺母的载荷和硬度要求Property Class 性能等级Nominal Nut Size (mm)义螺母尺Proof Load Stress (MPa)屈服点Hardness (HRC max)最大硬度5 4 to 36 incl. 570 308 4 to 36 incl. 910 309 4 to 16 incl. 990 3010 4 to 36 incl. 1040 26 - 36 <S>Hardness determination shall be made on a polished surface on the top or bottom nut face halfway between the thread and the hexagon corner or on a wrench face one-third of the distance from a hexagon corner to the center of the wrench face. Surface preparation prior to hardness testing shall be sufficient to remove decarburization or other surface irregularities.硬度的测定应在 滑的表面进行,测量点可 是在螺母 表面的螺 和 角角尖的中间,也可 是扳手表面从 角角尖到表面中部 分之一处,在测试前的表面准备应充分去除脱碳和其他不规则的形状Hardness tests shall be performed in accordance with the procedures outlined in the latest issue of SAE J417.硬度测试应按SAE J417 最 版本的纲要的程序进行5.1.2 Proof Load 保证载荷Nuts shall be capable of meeting the proof load requirements of their particular property class shown in Table 3 when tested as follows:特定的性能等级,如表3所示,螺母应满足保证载荷的要求如 ,TABLE 3: PROOF LOAD FOR METRIC SERIES STEEL NUTS表3: 制系列钢螺母的保证载荷Nominal Nut Size 义尺 Proof Load (Kilonewtons)保证载荷(千牛顿)TABLE 3: PROOF LOAD FOR METRIC SERIES STEEL NUTS表3: 制系列钢螺母的保证载荷Class 5 Class 8 Class 9 Class 10 <S>M 4 X 0.70 5.0 8.0 8.0 9.0M 5 X 0.80 8.0 13.0 14.0 15.0M 6 X 1.00 12.0 18.0 20.0 21.0M 8 X 1.25 21.0 33.0 36.0 38.0M 10 X 1.50 33.0 53.0 58.0 60.0M 12 X 1.75 48.0 77.0 84.0 88.0M 14 X 2.00 66.0 105.0 114.0 120.0M 16 X 2.00 90.0 143.0 155.0 163.0M 20 X 2.50 140.0 223.0 255.0M 24 X 3.00 200.0 321.0 367.0M 30 X 3.50 320.0 511.0 583.0M 36 X 4.00 466.0 743.0 850.0NOTE (1): The loads tabulated above were obtained by multiplying the proof load stress in Table 2, "Proof Load & Hardness Requirements for Metric Series Steel Nuts", by the bolt stress area. Proof loads for other sizes, pitches and property classes can be computed by using the appropriate value for proof load stress and stress area as computed by the formula in Table 4.注一: 述表格中的载荷是从表2 制系列的钢螺母的保证载荷硬度要求 的屈服点乘 倍数得到的，通过应力面 ， 其他面 螺距和性能等级的螺母的保证载荷可 通过相关的屈服点和应力面 值，用表4的 式计算得到TABLE 4: PROOF LOAD FORMULA 表4：保证应力的 式As = 0.7854 (D-O.9382 P)2Where: As = bolt stress area D = nominal bolt diameter P = thread pitch其中As=螺栓面 D= 义螺栓直径P=螺 螺距The nut shall be assembled on a test bolt or on a hardened and threaded mandrel (as described below) until at least three threads protrude. The specified proof load for the nut (See Table 3) shall be applied against the nut in an axial direction. The nut shall bear against a hardened steel plate at least one bolt diameter thick and having a clearance hole equal to basic bolt diameter plus 0.25 to 0.40 mm.螺母应装在一个测试螺栓或一个淬硬的螺 芯轴 面有 述 直到有最少3个螺距穿出螺母，规定的螺母保证载荷 表3 须在轴向施 在螺母 ，螺母应压在一块厚度不小于螺栓直径，有一个直径等于基本螺栓直径 0.25-0.40mm孔的淬硬钢 ，The nut shall resist the specified proof load without failure by stripping or rupture, and shall be removable from the test bolt or mandrel by the fingers after the load is released. (NOTE: Occasionally, it may be necessary to use a manual wrench of other means to start the nut in motion. Use of such means is permissible provided the nut is removable by the fingers following an initial loosening of not more than one-half turn of the nut.) If the threads of the test bolt or mandrel are damaged during the test, the test shall be discarded.螺母应能 规定的保证载荷，没有剥离和断裂失效，在试验载荷 消 可 用手指将其从螺栓 拧 ， 注：有时，需要其他手段用手动 手 拧 螺母一圈到一圈半，再用手拧 ，这是许可的 如果测试螺栓或芯轴在测试时坏掉了，测试就作废Test bolts shall have threads conforming to Class 6g tolerances and shall have a yield strength in excessof the specified proof load of the nut being tested.测试的螺栓需有6g的精度，在屈服强度 测试螺母规定的保证载荷有过剩Mandrels shall have a hardness of HRC 45 minimum; and shall be threaded to Class 6g tolerance, exceptthat the major diameter shall be the minimum major diameter with a tolerance of plus 0.05 mm.芯轴应有最小HRC45的硬度，螺 精度在6g级，除非螺 大径是最小大径 0.05mm 差For reference purposes, the proof load test shall be conducted using a hardened mandrel.作为参考目的，保证载荷测试应指导使用淬硬心轴5.2 Physical Properties and Tests物理特性和测试5.2.1 Surface Condition 表面情Property Classes MS-61709<S>-8, 9 and 10 nuts shall meet the surface discontinuity limits of Performance Standard PF-5189<S>.性能等级MS-61709 S -8，9和10的螺母应保证性能标准PF-5189 S 关于表面不连续性的限制6.0 IDENTIFICATION 标记When specified on the engineering drawing, these nuts shall be identified per Process Standard PS6151<S>.当工程图 有要求时，这些螺母应按过程标准PS6151 S 进行标记QUALITY 质量Refer to CS-9801 for general quality requirements.参考CS-9801来决定总的质量要求7.1 QS-9000QS-9000 defines the quality system expectations of DaimlerChrysler, Ford, General Motors, Truck Manufacturers and other subscribing companies for internal and external suppliers of production and service parts and materials. It is mandatory that the requirements of QS-9000 be met when supplying parts to this standard.QS-9000定义的是克莱斯勒，福特，通用，卡车制造厂和其他认购 内部或外部的产品，服 零件和材料的供应商的质量系统要求，按本标准 供零件时QS-9000的要求是强制要求执行的8.0 CONTROL 控制The minimum metallurgical and plating/coating checking requirements are described in Process Standard PS-10029. The minimum heat treat metallurgical checking requirements are described in Process Standard PS-10030.最 的 金的和涂覆的检查要求在过程标准PS-10029中有 述最 的热处理 金的检查要求在过程标准PS-10030中有 述GENERAL INFORMA TION 总的信息Three asterisks “***” after the section/paragraph header denotes multiple technical changes to the section/paragraph. A triple asterisk before and after a string of text (***text***) identifies a single change.在节/段的头部的 面跟 颗星 *** 表示该节/段有多重更改，在一窜字符的前 各 颗星 ***text*** 表示有单一的更改Certain important information relative to this standard has been included in separate standards. To assure the materials submitted meet all of DaimlerChrysler requirements, it is mandatory that the requirements in the following standards be met.某些和本标准相关的信息包 于独立的标准中，为了保证材料能满足所有克莱斯勒要求，强制要求 列标准必须满足CS-9800 - Application of this standard, the subscription service, and approved sourcesCS-9003 - Regulated substances and recyclabilityCS-9800-本标准的使用， 级单 ，批准的供应商CS-9003-限制物质和可追踪性Within Engineering Standards, the Regulatory (Government-mandated) requirements are designated by <S>, <E> and <H> which correspond to Safety, Emission and Homologation Shields respectively. The DCC-mandated requirements are designated by <D>, <A> and <T> and correspond to the Diamond, Appearance and Traceability symbols respectively.在工程标准中，规定的 政府命 的 要求指定为<S>,<E>,和<H>,他们分 应于安全，发射 辐射 和 素化保护，克莱斯勒命 的要求指定为<D>,<A>和 T ，它们分 应于菱形，外 和可追踪性For specific information on this document, please refer to the contact person shown in the "Publication Information" Section of this document. For general information on obtaining Engineering Standards and Laboratory Procedures, see CS-9800 or contact the Engineering Standards Department at engstds@.本文件中的特殊信息,请向本文件中’ 共信息”一节中的联系人员 得参考,, 获得工程标准和实验室程序的总的信息, CS-9800或在engstds@. 联系工程标准部门10.0 REFERENCES 参考CS-9003 CS-9800 CS-9801 MS-6149<S> MS-BAR<S> PS-1<S> PS-6151<S> PS-10029 PS-10030 PF-5189<S> PF-SAFETY QS-9000 SAE J41711.0 ENGINEERING APPROVED SOURCE LIST 工程批准的供应商清单Not applicable. 没有PUBLICATION INFORMATION发布信息Contact/Phone No: 联系人/电话 码：***Kerri Roche/(248) 512-3806***Alternate Contact/Phone No: 用联系人/电话 码***(248) 576-0652***Dept. Name & Dept. No./Tech Club/Organization: 部门 和部门 / 术俱乐部/组织Chassis & Powertrain Materials Engineering/ Dept. 5810Date Standard Originally (Initially) Published: 标准原始的发布日期1976-01-28Date Published出版日期: 2003-05-21Change Notice: 更改通知N/ADescription of Change: 更改的说明Format change and publication information 格式更改和发布信息# # # #。