汽车座椅安全性检查

2021/10/10
10
Safety Check—S16
S16:SIAB location 侧向安全气囊位置
Guide line: 1. SAB与座椅表面的尺寸满足右边图示尺寸，设计座椅撕裂线时，
气囊距撕裂线距离应为20～40mm。 2. SAB与座椅STO面的距离应为10～15mm
Carry over CF11 Back Frame and Airbag
19
Safety Check—S35
S35:Horizontal & Vertical distance between seat cushion STO and IP 座垫外表面到仪表板的垂直和水平距离
Design position 设计位置
2021/10/10
High & Forward most position 最前最高位置
2021/10/10
H+400
OK27
Comfort Check—C1
Guideline: >35
2021/10/10
Ht Check—C3
C3:Sections through the cushion every 100mm starting from H point perpendicular to track or thigh, mark min meat to metal dimension. Other dimension show seat symetrical. 从H点沿垂直滑道或大腿每一百毫米截面，每个截面显示最小MTM距离。其它尺寸显示座椅对称性
H+200
OK33
Comfort Check—C3 (Cushion)
Guideline: >50
2021/10/10
H+300
OK34
Comfort Check—C5,C6
C5:Sections through back starting from H point, along cross car direction every 100 mm on both side, mark min meat to metal dimension
2021/10/10
OK17
Safety Check—S32
S32:Sections through all Interior Protrusion requirement 所有内部突出物要求的截面
GB15083-2006: Area 3 R≥3.2
2021/10/10
OK18
Safety Check—S34
20
Comfort Check
2021/10/10
21
Comfort Check—C1
C1:Sections through the back every 100mm starting from H point perpendicular to torso line, mark min meat to metal dimension. Other dimension show seat symetrical. 从H点沿垂直靠背躯干线每一百毫米截面，每个截面显示最小MTM距离。其它尺寸显示座椅对称性
必须满足的法规RequiredRegulations
GB11550汽车座椅头枕性能要求和试验方法 GB15083汽车座椅系统强度要求及试验方法 GB14167安全带安装固定点 GB8410汽车内饰材料的燃烧特性 GB11552汽车内部突出物 GB11551关于正面碰撞乘员保护的设计规则 GB20071关于侧面碰撞乘员保护的设计规则
Safety Check—S29
S29:Pelvic impact Zone 臀部侧撞保护区域
Guideline: No Sharp edge
2021/10/10
13
Safety Check—S30
S30:Clearance for Eurosid II backplate for reduction of side impact forces on dummy ribs Eurosid II 模型靠背与靠背骨架夹角，减少侧撞对肋骨的伤害
2021/10/10
11
Safety Check—S17
S17:Clearance of seat back to B pillar for SIAB deployment 用于侧向安全气囊展开的座椅靠背到车身B柱距离
Guideline: >=60mm
2021/10/10
NOK for qoros 12
S9:Section through headrest showing the impact angle of 45 degrees from rear side 头枕截面显示从后部向头枕的45度角碰撞
2021/10/10
OK8
Safety Check—S10
S10:Safety belt anchorage zone (whole travel window) 安全带系统安装区域（所有行程范围）o
GB15083-2006 / ECE R17—高度750mm以下无使用位置，头枕高度不应低于 800mm
头枕处于最低位置
2021/10/10 Headrest in lowest position
头枕处于最高位置 Headrest in highest position
OK 3
Safety Check—S3
Guideline: >50
H+300mm H+200mm H+100mm H+0mm H-100mm
2021/10/10
29
Comfort Check—C3 (Cushion)
Guideline: >50
2021/10/10
H-100
OK30
Comfort Check—C3 (Cushion)
从H点沿着车身横向每一百毫米的座垫截面，显示最小MTM距离 Guideline: >50
Back
Cushion
2021/10/10
OK35
Comfort Check—C8
C8:Distance from H point to lumbar apex along torso line 沿靠背躯干线从H点到腰托顶点的距离
GB15083-2006 FMVSS 202a:头枕最低位置与靠背间隙不大 于25mm或165直径的球相切点间距不大于60mm
Headrest Carry over from CF14K
STO change to less than 15mm(CF11 14mm)
2021/10/10
7
Safety Check—S9
GB14167:α值应为30°~ 80°(非带扣侧)
2021/10/10
9
Safety Check—S10
S10:Safety belt anchorage zone (whole travel window) 安全带系统安装区域（所有行程范围）o
GB14167:α值应为45°~ 80°(带扣侧)
从H点沿着车身横向每一百毫米的靠背截面，显示最小MTM距离 Guideline: >35
C6:Sections through cushion starting from H point, along cross car direction every 100 mm on both side, mark min meat to metal dimension
2021/10/10
OK4
Safety Check—S6
S6:Distance from headrest top surface to headrest frame 从头枕上表面到头枕骨架的距离
fmvss 202a <25mm
2021/10/10
NA 5
Safety Check—S5,S7
S7:IIHS requirement on headrest by using HRMD 用头型测量设备（HRMD）对IIHS要求的校核
Guideline: >35
2021/10/10
H+500mm H+400mm H+300mm H+200mm H+100mm H+0mm
22
Comfort Check—C1
Guideline: >35
H+0 2021/10/10
OK23
Comfort Check—C1
Guideline: >35
H Point to Apex of Lumbar Lumbar Prominence
Guideline 135-150 90-110
2021/10/10
Move Lumbar Apex point lower
OK36
Comfort Check—C9
NA
2021/10/10
14
Safety Check—S31
S31:Anti-Submarining Guideline 防下潜区域检查（cushion）
2021/10/10
NO15
Safety Check—S32
S32:Sections through all Interior Protrusion requirement 所有内部突出物要求的截面
GB15083-2006: Area 1 R≥2.5
2021/10/10
OK16
Safety Check—S32
S32:Sections through all Interior Protrusion requirement 所有内部突出物要求的截面
GB15083-2006: Area 2 R≥5.0
S3:Section through headrest perpendicular to torso line and 65mm downward from headrest top surface 垂直靠背躯干线，从头枕上表面65mm向下的头枕截面
GB15083-2006 / ECE R17— ≥170mm for the width of head restraint
S34:Horizontal & Vertical distance between seat cushion STO and steering wheel 座垫外表面到方向盘的垂直和水平距离
Design position 设计位置
2021/10/10
High & Forward most position 最前最高位置
2021/10/10
H+100
OK24
Comfort Check—C1
Guideline: >35
2021/10/10
H+200
OK25
Comfort Check—C1
Guideline: >35
2021/10/10
H+300
OK26
Comfort Check—C1
Guideline: >35
Guideline: >50
CF16
CF11
H+0 2021/10/10
NOK31
Comfort Check—C3 (Cushion)
Guideline: >50
2021/10/10
H+100
OK32
Comfort Check—C3 (Cushion)
Guideline: >50
2021/10/10
Low Most Position
Middle Position
2021/10/10
Whiplash score issue, CF11 17mm
NOK 6
Safety Check—S8
S8:Requirement of head restraint gaps and clearance to seat back (upper most and lowest position) 头枕间隙以及头枕到座椅靠背间隙检查（头枕最高和最低位置）
ECER14SafetyBeltAnchorages
ECER17TheSeats,TheirAnchoragesandanyHeadRestraints
ECER21InteriorFittings
ECER44Childretrainsystems
E2C02E1R/1904/F1r0ontalcollision
1
Safety Check
2021/10/10
2
Safety Check—S1,S2
S1 S2:Distance from H point to headrest top surface at headrest full down/up position along torso angle 沿着靠背躯干线，从H点到头枕最低(最高)位置的上表面的距离.