LCD monitor结构设计指南
LCD Monitor 规格项目说明
LCD Monitor 规格项目说明购买者会考率因素不外乎亮暗点数、分辨率、显示颜色、亮度对比、可视角、反应时间、品牌等。
针对这些因素做下列简要说明:分辨率 在分辨率上，是与尺寸有相对关系的，除了少数特殊规格的机种，市面上的15"R液晶显示器可以显示的分辨率为1024x768，17"R、19"R的液晶显示器的分辨率则为1280x1024。
液晶显示器的显示是真实的每一画素点(pixel)，对应到软件显示的每一点，因此当它的分辨率是1024x768时，你的操作系统最好也是设定成一样的分辨率，不然变会出现模糊不清或怪异变形的画面，举例来说如果你设成800x600的解析度，显示器便要以1024个点来模拟800个点，你可以看出，在有些地方它便要以二个点来模拟一个点，有些地方却用一个点来显示一会出现变形的画面，有些字甚而会出现变粗的情形。
亮度 在亮度的值上，一个显示器拥有较高的亮度值理论上可以让画面更为亮丽，而一台液晶显示器最好拥有200 cd/m2以上的亮度值，才能显示出合宜的画面，当然若能有更高的亮度值自是更佳。
对比 对比指则是显示黑白之间的亮度层级，拥有高对比度的显示器便可以显示更为丰富的色彩层次，因此在对比值上最好能有200:1会较佳，不然你在看部分同色渐层的图片时可能会出现色块不均的状态，在显示质感上便较差了。
画面反应时间 另外反应时间对于长时间使用电玩软件或观看DVD、VCD等的使用者是最有关系的一环，所谓的反应时间便是指液晶显示器的每一个画素点(pixel)从暗到明或从明到暗的所需时间，一般在规格上标示均为二者的平均值，如果反应时间太长，便容易出现残影的情形，一般而言最好不要大于45ms，如果你对动态画面需求很大，就要追求反应时间更短的机种，如15ms以下的机种。
可视角 由于技术层面的不同，液晶显示器从侧面观看时会出现颜色偏差甚而看不清楚的情形，而在可视角度上又分为水平可视角与垂直可视角，不管是水平或垂直可视角二者最好最好都维持在120°以上，现在以TFT LCD之各机种皆可达此要求更新率 对于传统显示器上，我们为了防止画面闪烁，一定会注重显示器在各种分辨率下的垂直更新率，并让显示适配器与显示器配合，追求稳定的更新率，一般传统显示器至少要在75hz以上方能让人眼无法感觉画面在闪动，这是因为传统显示器是透过电子光束不断更新扫描，不断的在亮暗中切换，其更速度若是不足，人眼便容易感觉闪动。
G Series LCD Monitor G274QPX (3CC2) 用户指南说明书
G Series LCD Monitor G274QPX (3CC2)User GuideContentsGetting Started (3)Package Contents (3)Installing the Monitor Stand (4)Adjusting the Monitor (5)Monitor Overview (6)Connecting the Monitor to PC (8)OSD Setup (9)Navi Key (9)Hot Key (9)OSD Menus (10)Gaming (10)Professional (13)Image (14)Input Source (14)PIP/PBP (15)Navi Key (16)Setting (16)Specifications (18)Preset Display Modes (20)Troubleshooting (21)Safety Instructions (22)TÜV Rheinland Certification (24)Regulatory Notices (25)RevisionV1.0, 2023/022ContentsGetting StartedThis chapter provides you with the information on hardware setup procedures. While connecting devices, be careful in holding the devices and use a grounded wrist strap to avoid static electricity.∙Contact your place of purchase or local distributor if any of the items is damaged or missing.∙Package contents may vary by country.∙The included power cord is exclusively for this monitor and should not be used with other products.3Getting StartedInstalling the Monitor Stand1. Leave the monitor in its protective foam packaging. Align the stand bracket to the monitor groove.2. Tighten the stand bracket with screws.3. Connect the base to the stand and tighten the base screw to secure the base.4. Make sure the stand assembly is properly installed before setting the monitor Important ∙Place the monitor on a soft, protected surface to avoid scratching the display panel. ∙Do not use any sharp objects on the panel. ∙The groove for installing the stand bracket can also be used for wall mount. Please contact your dealer for proper wall mount kit. ∙This product comes with NO protective film to be removed by the user! Any mechanical damages to the product including removal of the polarizing film mayAdjusting the MonitorThis monitor is designed to maximize your viewing comfort with its adjustment capabilities.⚠ImportantAvoid touching the display panel when adjusting the monitor.90°90°5Getting StartedMonitor Overview6Getting Started7Getting StartedConnecting the Monitor to PC1. Turn off your computer.2. Connect the video cable from the monitor to your computer.3. Assemble the external power supply & power cord. (Figure A)4. Connect the external power supply to the monitor power jack. (Figure B)5. Plug the power cord into the electrical outlet. (Figure C)6. Turn on the monitor. (Figure D)7. Power on the computer and the monitor will auto detect the signal source.8Getting StartedOSD SetupThis chapter provides you with essential information on OSD Setup.⚠ImportantAll information is subject to change without prior notice.Navi KeyThe monitor comes with a Navi Key, a multi-directional control that helps navigate theUp/Down/Left/Right:∙selecting function menus and items∙adjusting function values∙entering into/exiting from function menusPress (OK):∙launching the On-Screen Display (OSD)∙entering submenus∙confirming a selection or settingHot Key∙Users may enter into preset function menus by moving the Navi Key up, down, left or right when the OSD menu is inactive.∙Users may customize their own Hot Keys to enter into different function menus.9OSD Setup10OSD Menus OSD Menus⚠ImportantThe following settings will be grayed out when HDR signals are received: ∙Night Vision ∙MPRT∙Low Blue Light ∙HDCR ∙Brightness ∙Contrast ∙Color Temperature ∙PIP/PBP11OSD Menus12OSD Menus13OSD Menus14OSD Menus15OSD Menus16OSD Menus17OSD Menus5.79A5.79A 18Specifications* Based on CIE1976 test standards.19SpecificationsPreset Display ModesImportant20Preset Display ModesTroubleshootingThe power LED is off.• Press the monitor power button again.• Check if the monitor power cable is properly connected.No image.• Check if the computer graphics card is properly installed.• Check if the computer and monitor are connected to electrical outlets and are turned on.• Check if the monitor signal cable is properly connected.• The computer may be in Standby mode. Press any key to activate the monitor. The screen image is not properly sized or centered.• Refer to Preset Display Modes to set the computer to a setting suitable for the monitor to display.No Plug & Play.• Check if the monitor power cable is properly connected.• Check if the monitor signal cable is properly connected.• Check if the computer and graphics card are Plug & Play compatible.The icons, font or screen are fuzzy, blurry or have color problems.• Avoid using any video extension cables.• Adjust brightness and contrast.• Adjust RGB color or tune color temperature.• Check if the monitor signal cable is properly connected.• Check for bent pins on the signal cable connector.The monitor starts flickering or shows waves.• Change the refresh rate to match the capabilities of your monitor.• Update your graphics card drivers.• Keep the monitor away from electrical devices that may cause electromagnetic interference (EMI).21TroubleshootingSafety Instructions∙Read the safety instructions carefully and thoroughly.∙All cautions and warnings on the device or User Guide should be noted.∙Refer servicing to qualified personnel only.Power∙Make sure that the power voltage is within its safety range and has been adjustedproperly to the value of 100~240V before connecting the device to the power outlet. ∙If the power cord comes with a 3-pin plug, do not disable the protective earth pinfrom the plug. The device must be connected to an earthed mains socket-outlet.∙Please confirm the power distribution system in the installation site shall providethe circuit breaker rated 120/240V, 20A (maximum).∙Always disconnect the power cord or switch the wall socket off if the device wouldbe left unused for a certain time to achieve zero energy consumption.∙Place the power cord in a way that people are unlikely to step on it. Do not placeanything on the power cord.∙If this device comes with an adapter, use only the MSI provided AC adapter approved for use with this device.BatteryPlease take special precautions if this device comes with a battery.∙Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer.∙Avoid disposal of a battery into fire or a hot oven, or mechanically crushing orcutting of a battery, which can result in an explosion.∙Avoid leaving a battery in an extremely high temperature or extremely low airpressure environment that can result in an explosion or the leakage of flammableliquid or gas.∙Do not ingest battery. If the coin/button cell battery is swallowed, it can causesevere internal burns and can lead to death. Keep new and used batteries awayfrom children.European Union:Batteries, battery packs, and accumulators should not be disposed of asunsorted household waste. Please use the public collection system toreturn, recycle, or treat them in compliance with the local regulations. BSMI:廢電池請回收For better environmental protection, waste batteries should be collectedseparately for recycling or special disposal.22Safety InstructionsCalifornia, USA:The button cell battery may contain perchlorate material and requiresspecial handling when recycled or disposed of in California.For further information please visit: https:///perchlorate/ Environment∙To reduce the possibility of heat-related injuries or of overheating the device, do not place the device on a soft, unsteady surface or obstruct its air ventilators.∙Use this device only on a hard, flat and steady surface.∙To prevent the device from tipping over, secure the device to a desk, wall or fixed object with an anti-tip fastener that helps to properly support the device and keep it safe in place.∙To prevent fire or shock hazard, keep this device away from humidity and high temperature.∙Do not leave the device in an unconditioned environment with a storage temperature above 60℃ or below -20℃, which may damage the device.∙The maximum operating temperature is around 40℃.∙When cleaning the device, be sure to remove the power plug. Use a piece of soft cloth rather than industrial chemical to clean the device. Never pour any liquid into the opening; that could damage the device or cause electric shock.∙Always keep strong magnetic or electrical objects away from the device.∙If any of the following situations arises, get the device checked by service personnel:• The power cord or plug is damaged.• Liquid has penetrated into the device.• The device has been exposed to moisture.• The device does not work well or you can not get it working according to the User Guide.• The device has dropped and damaged.• The device has obvious sign of breakage.23Safety InstructionsTÜV Rheinland CertificationTÜV Rheinland Low Blue Light CertificationBlue light has been shown to cause eye fatigueand discomfort. MSI now offers monitors with TÜVRheinland Low Blue Light certification to ensureusers’ eye comfort and well-being. Please followthe instructions below to reduce the symptoms fromextended exposure to the screen and blue light.∙Place the screen 20 – 28 inches (50 – 70 cm) away from your eyes and a little below eye level.∙Consciously blinking the eyes every now and then will help to reduce eye strain after extended screen time.∙Take breaks for 20 minutes every 2 hours.∙Look away from the screen and gaze at a distant object for at least 20 secondsduring breaks.∙Make stretches to relieve body fatigue or pain during breaks.∙Turn on the optional Low Blue Light function.TÜV Rheinland Flicker Free Certification∙TÜV Rheinland has tested this product toascertain whether the display produces visibleand invisible flicker for the human eye andtherefore strains the eyes of users.∙TÜV Rheinland has defined a catalogue oftests, which sets out minimum standardsat various frequency ranges. The test catalogue is based on internationallyapplicable standards or standards common within the industry and exceeds theserequirements.∙The product has been tested in the laboratory according to these criteria.∙The keyword “Flicker Free” confirms that the device has no visible and invisibleflicker defined in this standard within the range of 0 - 3000 Hz under variousbrightness settings.∙The display will not support Flicker Free when Anti Motion Blur/MPRT is enabled.(The availability of Anti Motion Blur/MPRT varies by products.)24TÜV Rheinland CertificationRegulatory NoticesCE ConformityThis device complies with the requirements set out in the Council Directive on the Approximation of the Laws of the Member Statesrelating to Electromagnetic Compatibility (2014/30/EU), Low-voltage Directive (2014/35/EU), ErP Directive (2009/125/EC) and RoHS directive (2011/65/EU). This product has been tested and found to comply with the harmonized standards for Information Technology Equipment published under Directives of Official Journal of the European Union.FCC-B Radio Frequency Interference StatementThis equipment has been tested and found to comply with the limitsfor a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, ifnot installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determinedby turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the measures listed below:∙Reorient or relocate the receiving antenna.∙Increase the separation between the equipment and receiver.∙Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.∙Consult the dealer or an experienced radio/television technician for help. Notice 1The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.Notice 2Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:1. This device may not cause harmful interference, and2. This device must accept any interference received, including interference that may cause undesired operation.MSI Computer Corp.901 Canada Court, City of Industry, CA 91748, USA(626) 913-082825Regulatory NoticesWEEE StatementUnder the European Union (“EU”) Directive on Waste Electrical and Electronic Equipment, Directive 2012/19/EU, products of “electrical and electronic equipment” cannot be discarded as municipal waste anymoreand manufacturers of covered electronic equipment will be obligated totake back such products at the end of their useful life. Chemical Substances InformationIn compliance with chemical substances regulations, such as the EU REACH Regulation (Regulation EC No. 1907/2006 of the European Parliament and the Council), MSI provides the information of chemical substances in products at: https:///global/indexRoHS StatementJapan JIS C 0950 Material DeclarationA Japanese regulatory requirement, defined by specification JIS C 0950, mandates that manufacturers provide material declarations for certain categories of electronic products offered for sale after July 1, 2006.https:///global/Japan-JIS-C-0950-Material-Declarations India RoHSThis product complies with the “India E-waste (Management and Handling) Rule 2016” and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for the exemptions set in Schedule 2 of the Rule. Turkey EEE RegulationConforms to the EEE Regulations of the Republic Of Turkey Ukraine Restriction of Hazardous SubstancesThe equipment complies with requirements of the Technical Regulation, approved by the Resolution of Cabinet of Ministry of Ukraine as of 10 March 2017, № 139, in terms of restrictions for the use of certain dangerous substances in electrical and electronic equipment.Vietnam RoHSAs from December 1, 2012, all products manufactured by MSI comply with Circular 30/2011/TT-BCT temporarily regulating the permitted limits for a number of hazardous substances in electronic and electric products.26Regulatory Notices27Regulatory Notices Green Product Features∙Reduced energy consumption during use and stand-by ∙Limited use of substances harmful to the environment and health∙Easily dismantled and recycled ∙Reduced use of natural resources by encouraging recycling ∙Extended product lifetime through easy upgrades ∙Reduced solid waste production through take-back policy Environmental Policy ∙The product has been designed to enable proper reuse of parts and recycling and should not be thrown away at its end of life. ∙Users should contact the local authorized point of collection for recycling and disposing of their end-of-life products. ∙Visit the MSI website and locate a nearby distributor for further recycling information. ∙*******************************************************************disposal, take-back, recycling, and disassembly of MSI products.Warning!Overuse of screens is likely to affect eyesight.Recommendations: 1. Take a 10-minute break for every 30 minutes of screen time. 2. Children under 2 years of age should have no screen time. For children aged 2 years and over, screen time should be limited to less than one hour per day.Copyright and Trademarks Notice Copyright © Micro-Star Int’l Co., Ltd. All rights reserved. The MSI logo used is a registered trademark of Micro-Star Int’l Co., Ltd. All other marks and names mentioned may be trademarks of their respective owners. No warranty as to accuracy or completeness is expressed or implied. MSI reserves the right to make changes to this document without prior notice.Technical Support If a problem arises with your product and no solution can be obtained from the user’s manual, please contact your place of purchase or local distributor. Alternatively,please visit https:///support/ for further guidance.。
Monitor用LCD面板背光源技术
Monitor用LCD面板以3D、背光源改善及画质提升为3大主题■林芬卉Display Taiwan 2007展中，Monitor用LCD面板着重3大主题，一是具高度娱乐功能的3D立体显示面板，二是背光源改善，三是逐渐提升画质表现。
3D LCD面板方面，CMO开发出须搭配偏光眼镜观看、方能呈现立体影像的3D面板；CPT则发表利用光栅（Barrier）、以裸视即可看到立体影像的面板。
背光源改善方面，CMO与CPT同时展示采RGB 3色LED背光的22寸Monitor用LCD面板。
另外，高色饱度CCFL背光亦被应用在Monitor用LCD面板，AUO展示一系列相关产品。
此外，过去仅着重在TV用LCD面板的高分辨率技术，此次Display Taiwan 2007已有CMO展示19”W Monitor用高分辨率LCD面板，而CPT则将Motion Blur Free技术导入22寸Monitor用LCD面板。
3D立体显示器用LCD面板发展CMO发表搭配偏光眼镜的22寸3D LCD面板CMO发表22寸宽屏幕3D立体显影LCD面板，主要针对3D游戏族群而设计。
此款3D 显示器需配合偏光眼镜观赏，好处是不需选择特定角度观看，且分辨率不受3D影像影响，CMO预计于2007年第3季开始量产。
CMO 3D显示器面板是以两组液晶面板所组成，其中一组结构与一般LCD面板同，另一组仅上下2片TFT玻璃中间夹一层液晶，主要目的在利用液晶旋光特性，区分垂直振动与水平振动2种偏光。
戴上眼镜后，其中一眼仅看到垂直振动光，另一眼则仅看到水平振动光，当两眼所得到影像在脑中形成双影重迭后，则会产生3D效果。
值得一提的是，此技术前提是在灰阶程度不同的影像部分，才会作垂直与水平偏光处理，故整体LCD面板分辨率下降程度有限。
另外，此款3D显示面板可切换2D与3D模式，在作一般文书处理或上网时，切换至2D 模式即可。
若欲切换至3D模式，影像内容亦须先以3D方式处理，否则播放一般2D影像，无法呈现3D效果。
CHIMEI 23LCD MONITOR 宽屏液晶显示器 说明书
预防措施
适用于欧盟国家的使用者信息 1 适用于美国的使用者信息 1 安装
1 电源连接 1 维护
1 搬运显示器 1
入门
包装内容 2 显示器安装
认识部件和控制按钮 3 定制您的显示器 3 使用OSD群组 3 热键介绍 功能键操作 4 OSD图标列表
5疑难解答
6
机能规格与特性
接口频率 7
附录
8
FCC达标 2
4
第三层
3.按在OSD 的跳出窗口上的对应的功能图标按键。
第二层
按右边第一个按键
功能时,按左边第二个按键 改变模式,你可以按 和 在4个模式间调整.
离开
图标
功能
详情
现象 检查项目
重要:注意确定显示设定并未超过VESA1920x1080@ 60Hz 。
机能规格与特性。
LCD监视器用户手册说明书
LCD MonitorUser ManualLegal InformationUser Manual©2018 Hangzhou Hikvision Digital Technology Co., Ltd.About this ManualThis Manual is subject to domestic and international copyright protection. Hangzhou Hikvision Digital Technology Co., Ltd. ("Hikvision") reserves all rights to this manual. This manual cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision.Please use this user manual under the guidance of professionals.Trademarksand other Hikvision marks are the property of Hikvision and are registered trademarks or the subject of applications for the same by Hikvision and/or its affiliates. Other trademarks mentioned in this manual are the properties of their respective owners. No right of license is given to use such trademarks without express permission.DisclaimerTO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, REGARDING THIS MANUAL. HIKVISION DOES NOT WARRANT, GUARANTEE, OR MAKE ANY REPRESENTATIONS REGARDING THE USE OF THE MANUAL, OR THE CORRECTNESS, ACCURACY, OR RELIABILITY OF INFORMATION CONTAINED HEREIN. YOUR USE OF THIS MANUAL AND ANY RELIANCE ON THIS MANUAL SHALL BE WHOLLY AT YOUR OWN RISK AND RESPONSIBILITY.REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.PerfaceSymbol ConventionsThe symbols that may be found in this document are defined as follows.Applicable ModelsThis manual is applicable to monitors of the following sizes: 22 inch, 32 inch, 43 inch, and 55 inch.ContentsChapter 1 Introduction (1)1.1 Overview (1)1.2 Key Features (1)1.3 Panel Buttons (1)1.4 Interfaces (2)1.5 Power Supply Connections (3)1.6 Remote Control (3)Chapter 2 Terminal Operations (5)2.1 Switch Input Source (5)2.2 Menu Descriptions (5)2.3 Configure Image Parameters (7)2.4 Configure Audio Settings (10)2.5 Enable/Disable keypad lock (11)2.6 System Maintenance (12)2.6.1 Upgrade the Device (12)2.6.2 Restore the Defaults (12)2.6.3 Configure Temperature Monitoring (13)2.6.4 View System Information (14)2.6.5 Enable/Disable Auto Sleep (15)2.6.6 Enable/Disable Power Saving Mode (15)2.6.7 Configure Screen Saver (15)2.6.8 Check Energy Diagram (15)Chapter 3 Client Operation (17)3.1 Log in to Client (17)3.2 Configure Serial Port (17)3.3 Startup/Shutdown (17)3.4 Switch Input Source (18)Chapter 1 Introduction1.1 OverviewThe LCD monitor is a reliable surveillance display with excellent color reduction, image processing, and true display of video details. Multiple interfaces can meet various surveillance environments, and build-in speaker is convenient for audio play. The monitor is an ideal choice for security and surveillance application.1.2 Key Features•8-bit 2-ch LVDS (1920 × 1080) HD display.•3D digital comb filter.•True color OSD and user-friendly operating menu.•Mstar ACE-5 auto color and image enhancement engine, improving the image contrast, details, color of skin and edges, etc.•Programmable 12-bit RGB gamma correction.•1-ch HDMI 1.3 input interface, supporting HDCP 1.2.•Software spread-spectrum technology to reduce EMI radiation.•3D noise reduction.•HD JPEG decoding.•Multimedia playing of text, image, audio, video, etc.1.3 Panel ButtonsTouch buttons place on the left side of the monitor. See details in the following figure and table.Table 1-1 Buttons Description1.4 InterfacesTable 1-2 Description of Rear Panel1.5 Power Supply ConnectionsInsert the 3-pin power plug (100 to 240 VAC, 2A) into well-grounded power socket.NoteDisconnect the power of the monitor if it will not be used for a long time.1.6 Remote ControlRefer to the following table for the remote controller descriptions.Figure 1-3 Remote ControlNoteThe following keys are only used under the USB signal source: , , , , , .Table 1-3 Description of Remote Control Buttons /Chapter 2 Terminal Operations2.1 Switch Input SourceThe monitor supports 5 signal sources: HDMI, DVI, VGA, CVBS , USB.Steps1.Press SOURCE to enter Input Source page.Figure 2-1 Input Source2.Press ▼ or ▲ to select the input source.3.Press OK to accomplish the input source selection.2.2 Menu DescriptionsMenu OperationsNoteConfiguration steps vary depending on the menu you choose.Table 2-1 Description of Menu Operations1Press MENU and the main menu appears on the screen, such as image mode, audio settings, VGA parameters, etc.2Press ▲/▼/◄/► to select a submenu.3Press OK to confirm the submenu.4Press ▲/▼ to select parameters.5Press ◄/► to set the parameters.6Press MENU to complete the settings and back to the main menu interface. OSD SettingsYou can set the language and OSD duration on the menu.Enter Menu Settings page: Menu→ Menu Settings , and then set language, OSD duration, and OSD blending.Figure 2-2 OSD SettingsLanguageSupports Chinese & English menu switch.OSD DurationRefers to the display time of the menu after it is not used. Press ◄ or ► to adjust the OSD duration to: Always On/5 Sec/15 Sec/30 Sec.OSD BlendingRefers to the OSD transparency. You can adjust the blending value to: High/Middle/Low/Off.2.3 Configure Image ParametersImage ModeYou can switch image modes and adjust image parameters including contrast, brightness, color, sharpness, and hue.Enter Image Mode page: MENU→ Image Mode , and then press ▲or▼to select Image Mode.Figure 2-3 Image ModeStandardSuitable for a normal environment.GentleSuitable for a dark room.DynamicSuitable for a bright room.UserWhen you select the User mode, press ◄ or ► to set the brightness, contrast, color, or sharpness to adjust display effect.NoteAdjustable parameters vary depending on the input source you choose. If the parameter bar is gray, it indicates that the parameter is unadjustable under the current input source.Backlight SettingsYou can adjust the screen brightness. The higher the backlight value, the brighter the screen.Enter Backlight Settings page: MENU→ Backlight Settings , and then press ▲ or ▼to select Backlight.Figure 2-4 Backlight SettingsVGA ParameterWhen you select VGA as the input source, you can adjust VGA parameters to make the picture show in the correct position.Enter VGA Parameter page: MENU→ VGA Parameter , and then press ▲ or ▼to adjust VGA parameters according to your needs.Figure 2-5 VGA ParameterOverscan SettingsWhen there is black border, you can shield the borders for better image quality.Enter Overscan Settings page: MENU→ Overscan Settings , and then press◄ or ► to disable Overscan. You can set Left Edge, Right Edge, Top Edge and Bottom Edge from 0 to 100.Figure 2-6 Oversan SettingsNoteThe value of overscan is the pixel value of certain edge.AspectYou can set the aspect ratio as 16:9, 4:3, and P-to-P to zoom pictures.Enter Aspect page: MENU→ Aspect , and then press ◄ or ► to set the aspect ratio.Figure 2-7 AspectImage FreezeImage freeze refers to freezing the current image on the monitor.Enter Image Freeze page: MENU→ Other Settings→ Image Freeze , and then press ◄ or ►to setImage Freeze as Yes or No to enable or disable the image freeze.After switching the input source, the image freeze is automatically disabled by default. LightingYou can set the lighting parameters to adopt different surrounding lighting conditions.Enter Lighting page: MENU→ Other Settings→ Lighting , and then press ◄ or ► to switch lighting modes.Normal ModeSuitable for normal light conditions.Daylight ModeSuitable for daylight conditions.Night ModeSuitable for night light conditions.2.4 Configure Audio SettingsYou can switch the mute on/off, and adjust the volume/balance.Enter Audio Mode page: Menu→ Audio Mode , and then press ◄ or ► to set the mute, volume, and balance.Figure 2-8 Audio Settings2.5 Enable/Disable keypad lockYou can disable keypad lock to avoid the misoperation of control panel buttons.Enter Lock Keypad page: MENU→ Lock Keypad , and then press ◄ or ► to turn on/off Lock Keypad.Figure 2-9 Lock KeypadNoteWhen the lock keypad keypad lock is enabled, the control panel buttons are invalid.2.6 System MaintenanceThe device supports functions such as viewing system information, upgrading software, high temperature protection, no signal screensaver.2.6.1 Upgrade the DevicePlease use the latest update package to get all the possible updates.Before You StartInsert the USB flash drive with the update package to the device.Steps1.Enter Upgrade(USB) page: MENU→ Maintenance→ Upgrade(USB) .2.Press ►to to start upgrading.3.Press ◄ to continue the upgrading process or ► to cancel the operation and back to the menu.2.6.2 Restore the DefaultsAll parameters of the device can be restored to default settings.Steps1.Enter Restore Defaults page: MENU→ Restore Defaults .Figure 2-10 Restore Defaults2.Press ►to start restoration.A dialog box pops up.3.Press ◄ to continue restoring the defaults or ► to cancel the operation and back to the menu.2.6.3 Configure Temperature MonitoringYou can enable Overheat Alarm and once the board temperature is too high, an alarm prompt appears on the screen.Steps1.Enter Alarm Settings page: MENU→ Alarm Settings .2.Press ◄or ► to enable/disable Overheat Alarm.Figure 2-11 Alarm Settings3.Select Alarm Temp (°C) and press ◄ or ► to adjust the alarm temperature.4.Press MENU again to complete the settings and back to the main menu interface.2.6.4 View System InformationView the system information for maintenance.Enter System Info page: MENU→ System Info , and check current software version, working hours,current temperature, device ID.Figure 2-12 System Information2.6.5 Enable/Disable Auto SleepWhen the monitor does not have signal input in a preset interval, it goes to sleep automatically. Steps1.Enter Auto Sleep page: MENU→ Backlight Settings→ Auto Sleep .2.Press ◄ or ► to set Auto Sleep value or turn off Auto Sleep.3.Press MENU again to complete the settings and back to the main menu interface.2.6.6 Enable/Disable Power Saving ModeThe Power Saving Mode can reduce screen brightness and power consumption.Steps1.Enter Power Saving Mode page: MENU→ Other Settings→ Power Saving Mode .2.Press◄ or ►to enable/disable Power Saving Mode.3.Press MENU again to complete the settings and back to the main menu interface.2.6.7 Configure Screen SaverThe screen saver allows you to set the screen mode when the monitor has no signal input. Steps1.Enter No Signal Screensaver page: MENU→ Other Settings→ No Signal Screensaver .2.Press ◄ or ► to set Blue or Black or LOGO when there is no signal input.3.Press MENU again to complete the settings and back to the main menu interface.2.6.8 Check Energy DiagramYou can confirm the working condition of power saving mode and check current power, the power ratio, the sum power of the monitor.Steps1.Enter Energy Diagram page: MENU→ Other Settings→ Energy Diagram .2.Press ► to enable Energy Diagram.3.Press MENU again to complete the settings and back to the main menu interface.Figure 2-13 Energy DiagramThe Energy Diagram appears on the top left of the screen.Current PowerThe current power of the device.Power RatioThe ratio of the current power to the maximum power.Sum PowerThe total power accumulated from the factory to the present.4.Optional:Turn off Energy Diagram.1)Repeat step 1, and press ► to disable Energy Diagram.2)Press MENU again to complete the settings and back to the main menu interface.Chapter 3 Client OperationYou can turn on/off the monitor, switch the input signal through the ScreenControl client.3.1 Log in to ClientIf you use the client software for the first time, set Control Mode and Screen Type. Before You StartObtain the ScreenControl software from the CD-ROM and install it.Steps1.Double-click the client software shortcut to open the client.2.Select Control Mode to serial port.3.Select Screen Type to LCD-D50.4.Select User Name to guest.5.Click Login to log in to the client software.3.2 Configure Serial PortThe client controls the screen by connecting the serial port.Steps1.Click System Configuration→ Serial Port Configuration .2.Select Serial Port.3.Set Buad Rate to 9600.4.Click Open to connect the serial port.5.Optional:Click Close to disconnect the serial port.3.3 Startup/ShutdownYou can turn on/off the monitors via the client.Before You StartConfigure the serial port, and see Configure Serial Port for details.Steps1.Open the Screen Control page.2.Hold the mouse to draw a rectangle to select one or multiple virtual screens.3.Turn on/off the monitors.-Right click to select Startup/Shutdown.-Click to turn off the monitors. Or click to turn on the monitors.3.4 Switch Input SourceYou can switch the input source via the client.Before You StartConfigure the serial port, and see Configure Serial Port for details.Steps1.Open the Screen Control page.2.Hold the mouse to draw a rectangle to select one or multiple virtual screens.3.Right click and select Switch Signal.4.Select the source according to your needs.。
19寸 TFT-LCD Monitor 使用指南
目錄產品 (2)目錄 (2)功能 (2)省電裝置 (2)即插即用 (2)安全 (3)電器 (3)一般問題 (4)設定您的LCD顯示器 (5)安裝 (5)螢幕調整 (5)OSD 控制 (6)說明 (8)故障排除 (9)產品保養 (10)產品註：請保存原包裝盒與包裝材料，以方便日後運送。
目錄LCD 顯示器與底座，請參閱快速設定。
本型號LCD 顯示器配件，請參閱快速設定。
功能影像高亮度 重量輕巧 反應時間快速立體聲喇叭 (如果沒有安裝揚聲器，此項請略過。
) 省電功能 低電磁波輻射 Kensington 安全卡鎖 安全認證省電裝置LCD 顯示器內建電源控制系統，也稱為（省電裝置）。
如有一段時間不使用顯示器時，系統會將顯示器切換到低電壓模式，以節省電力。
稍微移動滑鼠或按下鍵盤按鍵，即可切換到原始畫面。
電腦內的VGA 卡可處理省電裝置功能；您可使用電腦設定此功能。
搭配VESA DPMS 電腦時，本LCD 顯示器與EPA ENERGY STAR 及NÜTEK 相容。
不使用LCD 顯示器時，為了節省電力，請關閉LCD 顯示器的電源。
即插即用新的VESA Plug and Play （VESA 即插即用）功能可簡化複雜與費時的安裝程序。
使用即插即用系統時，不會遭遇常見的安裝問題。
您的電腦系統可輕易識別，並自動調整顯示器。
LCD 顯示器使用Display Data Channel (DDC 顯示資料通道)對電腦系統送出Extended Display Identification Data (EDID 延伸顯示識別資料)，因此電腦系統可設定顯示器自動調整。
安全注意：使用顯示器之前，請注意以下的安全警告。
電器檢查電壓本產品應使用標籤上註明的電源形式進行操作，若您不確定可用的電源形式，請洽詢您的經銷商或當地的電力公司。
電擊本產品配有三頭式接地插頭，其中第三頭為接地線。
本插頭只能與三孔式接地電源插座配合使用；接地線是本插座插頭在安全上的功能，若您無法將插頭插入電源插座，請洽詢您的電器技師更換舊式插座。
PRO Series LCD Monitor MP2422C (3PB0) 用户指南说明书
PRO Series LCD Monitor MP2422C (3PB0)User GuideContentsGetting Started (3)Package Contents (3)Installing the Monitor Stand (4)Adjusting the Monitor (5)Monitor Overview (6)Connecting the Monitor to PC (8)OSD Setup (9)Navi Key (9)Hot Key (9)OSD Menus (10)Picture (10)Color (11)Audio (12)System (12)Information (14)Specifications (15)Preset Display Modes (17)Troubleshooting (18)Safety Instructions (19)TÜV Rheinland Certification (21)ENERGY STAR Certification (21)Regulatory Notices (22)RevisionV1.0, 2023/072ContentsGetting StartedThis chapter provides you with the information on hardware setup procedures. While connecting devices, be careful in holding the devices and use a grounded wrist strap to avoid static electricity.∙Contact your place of purchase or local distributor if any of the items is damaged or missing.∙Package contents may vary by country.∙The included power cord is exclusively for this monitor and should not be used with other products.3Getting StartedInstalling the Monitor Stand 1. Leave the monitor in its protective foam packaging. Align the stand bracket to the monitor groove.2. Push the stand towards the monitor groove until it locks in place.3. Connect the base to the stand to secure the base.4. Make sure the stand assembly is properly installed before setting the monitor upright.23⚠Important ∙Place the monitor on a soft, protected surface to avoid scratching the display panel. ∙Do not use any sharp objects on the panel. ∙The groove for installing the stand bracket can also be used for wall mount. Please contact your dealer for proper wall mount kit. ∙This product comes with NO protective film to be removed by the user! Any mechanical damages to the product including removal of the polarizing film may affect the warranty!Adjusting the MonitorThis monitor is designed to maximize your viewing comfort with its adjustment capabilities.⚠ImportantAvoid touching the display panel when adjusting the monitor.∙5Getting StartedMonitor Overview6Getting Started7 Getting StartedConnecting the Monitor to PC1. Turn off your computer.2. Connect the video cable from the monitor to your computer.3. Assemble the external power supply & power cord. (Figure A)4. Connect the external power supply to the monitor power jack. (Figure B)5. Plug the power cord into the electrical outlet. (Figure C)6. Turn on the monitor. (Figure D)7. Power on the computer and the monitor will auto detect the signal source.8Getting StartedOSD SetupThis chapter provides you with essential information on OSD Setup.⚠ImportantAll information is subject to change without prior notice.Navi KeyThe monitor comes with a Navi Key, a multi-directional control that helps navigate theOn-Screen Display (OSD) menu.Up/Down/Left/Right:∙selecting function menus and items∙adjusting function values∙entering into/exiting from function menusPress (Enter):∙launching the On-Screen Display (OSD)∙entering submenus∙confirming a selection or settingHot Key∙Users may enter into preset function menus by moving the Navi Key up, down, left or right when the OSD menu is inactive.9OSD Setup10OSD Menus11OSD Menus12OSD Menus13OSD Menus14OSD Menus2W x 212V 2.5AModel: SOY-1200250-09712V 2.5A-7° ~ 22°15Specifications* Based on CIE1976 test standards. 16SpecificationsPreset Display ModesImportant17Preset Display ModesTroubleshootingThe power LED is off.• Press the monitor power button again.• Check if the monitor power cable is properly connected.No image.• Check if the computer graphics card is properly installed.• Check if the computer and monitor are connected to electrical outlets and areturned on.• Check if the monitor signal cable is properly connected.• The computer may be in Standby mode. Press any key to activate the monitor. The screen image is not properly sized or centered.• Refer to Preset Display Modes to set the computer to a setting suitable for themonitor to display.No Plug & Play.• Check if the monitor power cable is properly connected.• Check if the monitor signal cable is properly connected.• Check if the computer and graphics card are Plug & Play compatible. The icons, font or screen are fuzzy, blurry or have color problems.• Avoid using any video extension cables.• Adjust brightness and contrast.• Adjust RGB color or tune color temperature.• Check if the monitor signal cable is properly connected.• Check for bent pins on the signal cable connector.The monitor starts flickering or shows waves.• Change the refresh rate to match the capabilities of your monitor.• Update your graphics card drivers.• Keep the monitor away from electrical devices that may cause electromagneticinterference (EMI).18TroubleshootingSafety Instructions∙Read the safety instructions carefully and thoroughly.∙All cautions and warnings on the device or User Guide should be noted.∙Refer servicing to qualified personnel only.Power∙Make sure that the power voltage is within its safety range and has been adjusted properly to the value of 100~240V before connecting the device to the power outlet. ∙If the power cord comes with a 3-pin plug, do not disable the protective earth pin from the plug. The device must be connected to an earthed mains socket-outlet.∙Please confirm the power distribution system in the installation site shall provide the circuit breaker rated 120/240V, 20A (maximum).∙Always disconnect the power cord or switch the wall socket off if the device would be left unused for a certain time to achieve zero energy consumption.∙Place the power cord in a way that people are unlikely to step on it. Do not place anything on the power cord.∙If this device comes with an adapter, use only the MSI provided AC adapter approved for use with this device.BatteryPlease take special precautions if this device comes with a battery.∙Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer.∙Avoid disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, which can result in an explosion.∙Avoid leaving a battery in an extremely high temperature or extremely low air pressure environment that can result in an explosion or the leakage of flammable liquid or gas.∙Do not ingest battery. If the coin/button cell battery is swallowed, it can cause severe internal burns and can lead to death. Keep new and used batteries away from children.European Union:Batteries, battery packs, and accumulators should not be disposed of asunsorted household waste. Please use the public collection system toreturn, recycle, or treat them in compliance with the local regulations. BSMI:廢電池請回收For better environmental protection, waste batteries should be collectedseparately for recycling or special disposal.19Safety InstructionsCalifornia, USA:The button cell battery may contain perchlorate material and requiresspecial handling when recycled or disposed of in California.For further information please visit: https:///perchlorate/ Environment∙To reduce the possibility of heat-related injuries or of overheating the device, do not place the device on a soft, unsteady surface or obstruct its air ventilators.∙Use this device only on a hard, flat and steady surface.∙To prevent the device from tipping over, secure the device to a desk, wall or fixedobject with an anti-tip fastener that helps to properly support the device and keep it safe in place.∙To prevent fire or shock hazard, keep this device away from humidity and hightemperature.∙Do not leave the device in an unconditioned environment with a storage temperature above 60℃ or below -20℃, which may damage the device.∙The maximum operating temperature is around 40℃.∙When cleaning the device, be sure to remove the power plug. Use a piece of softcloth rather than industrial chemical to clean the device. Never pour any liquid into the opening; that could damage the device or cause electric shock.∙Always keep strong magnetic or electrical objects away from the device.∙If any of the following situations arises, get the device checked by service personnel:• The power cord or plug is damaged.• Liquid has penetrated into the device.• The device has been exposed to moisture.• The device does not work well or you can not get it working according to the UserGuide.• The device has dropped and damaged.• The device has obvious sign of breakage.20Safety InstructionsENERGY STAR Certification ENERGY STAR is a program run by the U.S. Environmental Protection Agency (EPA) and U.S. Department of Energy (DOE) to promote energy efficiency. This product qualifies for ENERGY STAR in the “factory default” settings through which power savings will be achieved. Changing the factory default picture settings or enabling other features will increase power consumption, which could exceed the limits necessary to qualify for ENERGY STAR rating. For more information on ENERGY STAR, refer to https:///.21TÜV Rheinland Certification TÜV Rheinland CertificationTÜV Rheinland Low Blue Light Certification Blue light has been shown to cause eye fatigue and discomfort. MSI now offers monitors with TÜV Rheinland Low Blue Light certification to ensure users’ eye comfort and well-being. Please follow the instructions below to reduce the symptoms from extended exposure to the screen and blue light. ∙Place the screen 20 – 28 inches (50 – 70 cm) away from your eyes and a little below eye level.∙Consciously blinking the eyes every now and then will help to reduce eye strain after extended screen time.∙Take breaks for 20 minutes every 2 hours. ∙Look away from the screen and gaze at a distant object for at least 20 seconds during breaks. ∙Make stretches to relieve body fatigue or pain during breaks. ∙Turn on the optional Low Blue Light function.TÜV Rheinland Flicker Free Certification ∙TÜV Rheinland has tested this product to ascertain whether the display produces visible and invisible flicker for the human eye and therefore strains the eyes of users. ∙TÜV Rheinland has defined a catalogue of tests, which sets out minimum standards at various frequency ranges. The test catalogue is based on internationally applicable standards or standards common within the industry and exceeds these requirements. ∙The product has been tested in the laboratory according to these criteria. ∙The keyword “Flicker Free” confirms that the device has no visible and invisible flicker defined in this standard within the range of 0 - 3000 Hz under various brightness settings. ∙The display will not support Flicker Free when Anti Motion Blur/MPRT is enabled. (The availability of Anti Motion Blur/MPRT varies by products.)Regulatory NoticesCE ConformityThis device complies with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility (2014/30/EU), Low-voltage Directive (2014/35/EU), ErP Directive (2009/125/EC) and RoHS directive (2011/65/EU). This product has been tested and found to comply with the harmonized standards for Information Technology Equipment published under Directives of Official Journal of the European Union.FCC-B Radio Frequency Interference StatementThis equipment has been tested and found to comply with the limitsfor a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, ifnot installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the measures listed below:∙Reorient or relocate the receiving antenna.∙Increase the separation between the equipment and receiver.∙Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.∙Consult the dealer or an experienced radio/television technician for help. Notice 1The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Notice 2Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:1. This device may not cause harmful interference, and2. This device must accept any interference received, including interference that maycause undesired operation.MSI Computer Corp.901 Canada Court, City of Industry, CA 91748, USA(626) 913-082822Regulatory NoticesWEEE StatementUnder the European Union (“EU”) Directive on Waste Electrical and Electronic Equipment, Directive 2012/19/EU, products of “electrical and electronic equipment” cannot be discarded as municipal waste anymoreand manufacturers of covered electronic equipment will be obligated totake back such products at the end of their useful life. Chemical Substances InformationIn compliance with chemical substances regulations, such as the EU REACH Regulation (Regulation EC No. 1907/2006 of the European Parliament and the Council), MSI provides the information of chemical substances in products at: https:///global/indexRoHS StatementJapan JIS C 0950 Material DeclarationA Japanese regulatory requirement, defined by specification JIS C 0950, mandates that manufacturers provide material declarations for certain categories of electronic products offered for sale after July 1, 2006.https:///global/Japan-JIS-C-0950-Material-DeclarationsIndia RoHSThis product complies with the “India E-waste (Management and Handling) Rule 2016” and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenylsor polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for the exemptions set in Schedule 2 of the Rule. Turkey EEE RegulationConforms to the EEE Regulations of the Republic Of TurkeyUkraine Restriction of Hazardous SubstancesThe equipment complies with requirements of the Technical Regulation, approved by the Resolution of Cabinet of Ministry of Ukraine as of 10 March 2017, № 139, in terms of restrictions for the use of certain dangerous substances in electrical and electronic equipment.Vietnam RoHSAs from December 1, 2012, all products manufactured by MSI comply with Circular 30/2011/TT-BCT temporarily regulating the permitted limits for a number of hazardous substances in electronic and electric products.23Regulatory Notices24Regulatory Notices Green Product Features∙Reduced energy consumption during use and stand-by ∙Limited use of substances harmful to the environment and health∙Easily dismantled and recycled ∙Reduced use of natural resources by encouraging recycling ∙Extended product lifetime through easy upgrades ∙Reduced solid waste production through take-back policy Environmental Policy ∙The product has been designed to enable proper reuse of parts and recycling and should not be thrown away at its end of life. ∙Users should contact the local authorized point of collection for recycling and disposing of their end-of-life products. ∙Visit the MSI website and locate a nearby distributor for further recycling information. ∙*******************************************************************disposal, take-back, recycling, and disassembly of MSI products.Warning!Overuse of screens is likely to affect eyesight.Recommendations: 1. Take a 10-minute break for every 30 minutes of screen time. 2. Children under 2 years of age should have no screen time. For children aged 2 years and over, screen time should be limited to less than one hour per day.Copyright and Trademarks Notice Copyright © Micro-Star Int’l Co., Ltd. All rights reserved. The MSI logo used is a registered trademark of Micro-Star Int’l Co., Ltd. All other marks and names mentioned may be trademarks of their respective owners. No warranty as to accuracy or completeness is expressed or implied. MSI reserves the right to make changes to this document without prior notice.The terms HDMI™, HDMI™ High-Definition Multimedia Interface, HDMI™ Trade dress and the HDMI™ Logos are trademarks or registered trademarks of HDMI™ Licensing Administrator, Inc.Technical Support If a problem arises with your product and no solution can be obtained from the user’s manual, please contact your place of purchase or local distributor. Alternatively,please visit https:///support/ for further guidance.。
PRO Series LCD Monitor 用户指南说明书
PRO Series LCD MonitorPRO MP243P (3PB5) PRO MP273P (3PB4) PRO MP273QP (3PB6) PRO MP273QV (3PB6)User GuideContentsGetting Started (3)Package Contents (3)Installing the Monitor Stand (4)Adjusting the Monitor (6)Monitor Overview (8)Connecting the Monitor to PC (11)OSD Setup (13)OSD Keys (13)OSD Menus (14)Professional (15)Image (17)Input Source (18)Navi Key (19)Setting (20)Specifications (22)Preset Display Modes (24)Troubleshooting (25)Safety Instructions (26)TÜV Rheinland Certification (28)ENERGY STAR Certification (28)Regulatory Notices (29)RevisionV1.0, 2022/112ContentsGetting StartedThis chapter provides you with the information on hardware setup procedures. While connecting devices, be careful in holding the devices and use a grounded wrist strap to avoid static electricity.∙Contact your place of purchase or local distributor if any of the items is damaged or missing.∙Package contents may vary by country.∙The included power cord is exclusively for this monitor and should not be used with other products.3Getting StartedInstalling the Monitor StandPRO MP243P, PRO MP273P, PRO MP273QP1. Leave the monitor in its protective foam packaging. Align the stand bracket to themonitor groove.2. Tighten the stand bracket with screws.3. Connect the base to the stand and tighten the base screw to secure the base.4. Make sure the stand assembly is properly installed before setting the monitorupright.4Getting Started5Getting Started PRO MP273QV 1. Leave the monitor in its protective foam packaging. Align the stand bracket to the monitor.2. Connect the base to the stand to secure the base.3. Make sure the stand assembly is properly installed before setting the monitor upright.⚠Important ∙Place the monitor on a soft, protected surface to avoid scratching the display panel. ∙Do not use any sharp objects on the panel. ∙The back of the monitor can also be used for wall mount. Please contact your dealer for proper wall mount kit. ∙This product comes with NO protective film to be removed by the user! Any mechanical damages to the product including removal of the polarizing film mayaffect the warranty!6Getting Started Adjusting the Monitor This monitor is designed to maximize your viewing comfort with its adjustment capabilities.PRO MP243P, PRO MP273P, PRO MP273QP90°90°PRO MP273QV⚠Important∙Avoid touching the display panel when adjusting the monitor.∙Please slightly tilt the monitor backwards before pivoting it.7Getting StartedMonitor Overview8Getting StartedPRO MP273QV9Getting Started10Getting StartedConnecting the Monitor to PCPRO MP243P, PRO MP273P, PRO MP273QP1. Turn off your computer.2. Connect the video cable from the monitor to your computer.3. Assemble the external power supply & power cord. (Figure A)4. Connect the external power supply to the monitor power jack. (Figure B)5. Plug the power cord into the electrical outlet. (Figure C)6. Turn on the monitor. (Figure D)7. Power on the computer and the monitor will auto detect the signal source.11Getting StartedPRO MP273QV1. Turn off your computer.2. Connect the video cable from the monitor to your computer.3. Assemble the external power supply & power cord. (Figure A)4. Connect the external power supply to the monitor power jack. (Figure B)5. Plug the power cord into the electrical outlet. (Figure C)6. Turn on the monitor. (Figure D)7. Power on the computer and the monitor will auto detect the signal source.12Getting StartedOSD SetupThis chapter provides you with essential information on OSD Setup.⚠ImportantAll information is subject to change without prior notice.OSD KeysThe monitor comes with a set of OSD Keys that help to control the On-Screen Display (OSD) menu.13OSD SetupOSD MenusPRO MP243P/ PRO MP273PPRO MP273QP / PRO MP273QV⚠ImportantThe following settings will be grayed out when HDR signals are received:∙HDCR∙Brightness14OSD Menus15OSD MenusNone 16OSD Menus17OSD Menus18OSD Menus19 OSD Menus20OSD Menus21OSD Menus12V 12V 22Specifications* Based on CIE1976 test standards.23SpecificationsPreset Display ModesImportant24Preset Display ModesTroubleshootingThe power LED is off.• Press the monitor power button again.• Check if the monitor power cable is properly connected.No image.• Check if the computer graphics card is properly installed.• Check if the computer and monitor are connected to electrical outlets and are turned on.• Check if the monitor signal cable is properly connected.• The computer may be in Standby mode. Press any key to activate the monitor. The screen image is not properly sized or centered.• Refer to Preset Display Modes to set the computer to a setting suitable for the monitor to display.No Plug & Play.• Check if the monitor power cable is properly connected.• Check if the monitor signal cable is properly connected.• Check if the computer and graphics card are Plug & Play compatible.The icons, font or screen are fuzzy, blurry or have color problems.• Avoid using any video extension cables.• Adjust brightness and contrast.• Adjust RGB color or tune color temperature.• Check if the monitor signal cable is properly connected.• Check for bent pins on the signal cable connector.The monitor starts flickering or shows waves.• Change the refresh rate to match the capabilities of your monitor.• Update your graphics card drivers.• Keep the monitor away from electrical devices that may cause electromagnetic interference (EMI).25TroubleshootingSafety Instructions∙Read the safety instructions carefully and thoroughly.∙All cautions and warnings on the device or User Guide should be noted.∙Refer servicing to qualified personnel only.Power∙Make sure that the power voltage is within its safety range and has been adjustedproperly to the value of 100~240V before connecting the device to the power outlet. ∙If the power cord comes with a 3-pin plug, do not disable the protective earth pinfrom the plug. The device must be connected to an earthed mains socket-outlet.∙Please confirm the power distribution system in the installation site shall providethe circuit breaker rated 120/240V, 20A (maximum).∙Always disconnect the power cord or switch the wall socket off if the device wouldbe left unused for a certain time to achieve zero energy consumption.∙Place the power cord in a way that people are unlikely to step on it. Do not placeanything on the power cord.∙If this device comes with an adapter, use only the MSI provided AC adapter approved for use with this device.BatteryPlease take special precautions if this device comes with a battery.∙Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer.∙Avoid disposal of a battery into fire or a hot oven, or mechanically crushing orcutting of a battery, which can result in an explosion.∙Avoid leaving a battery in an extremely high temperature or extremely low airpressure environment that can result in an explosion or the leakage of flammableliquid or gas.∙Do not ingest battery. If the coin/button cell battery is swallowed, it can causesevere internal burns and can lead to death. Keep new and used batteries awayfrom children.European Union:Batteries, battery packs, and accumulators should not be disposed of asunsorted household waste. Please use the public collection system toreturn, recycle, or treat them in compliance with the local regulations. BSMI:廢電池請回收For better environmental protection, waste batteries should be collectedseparately for recycling or special disposal.26Safety InstructionsCalifornia, USA:The button cell battery may contain perchlorate material and requiresspecial handling when recycled or disposed of in California.For further information please visit: https:///perchlorate/ Environment∙To reduce the possibility of heat-related injuries or of overheating the device, do not place the device on a soft, unsteady surface or obstruct its air ventilators.∙Use this device only on a hard, flat and steady surface.∙To prevent the device from tipping over, secure the device to a desk, wall or fixed object with an anti-tip fastener that helps to properly support the device and keep it safe in place.∙To prevent fire or shock hazard, keep this device away from humidity and high temperature.∙Do not leave the device in an unconditioned environment with a storage temperature above 60℃ or below -20℃, which may damage the device.∙The maximum operating temperature is around 40℃.∙When cleaning the device, be sure to remove the power plug. Use a piece of soft cloth rather than industrial chemical to clean the device. Never pour any liquid into the opening; that could damage the device or cause electric shock.∙Always keep strong magnetic or electrical objects away from the device.∙If any of the following situations arises, get the device checked by service personnel:• The power cord or plug is damaged.• Liquid has penetrated into the device.• The device has been exposed to moisture.• The device does not work well or you can not get it working according to the User Guide.• The device has dropped and damaged.• The device has obvious sign of breakage.27Safety InstructionsTÜV Rheinland CertificationTÜV Rheinland Low Blue Light CertificationBlue light has been shown to cause eye fatigueand discomfort. MSI now offers monitors with TÜVRheinland Low Blue Light certification to ensureusers’ eye comfort and well-being. Please followthe instructions below to reduce the symptoms fromextended exposure to the screen and blue light.∙Place the screen 20 – 28 inches (50 – 70 cm) away from your eyes and a little below eye level.∙Consciously blinking the eyes every now and then will help to reduce eye strain after extended screen time.∙Take breaks for 20 minutes every 2 hours.∙Look away from the screen and gaze at a distant object for at least 20 secondsduring breaks.∙Make stretches to relieve body fatigue or pain during breaks.∙Turn on the optional Low Blue Light function.TÜV Rheinland Flicker Free Certification∙TÜV Rheinland has tested this product toascertain whether the display produces visibleand invisible flicker for the human eye andtherefore strains the eyes of users.∙TÜV Rheinland has defined a catalogue oftests, which sets out minimum standardsat various frequency ranges. The test catalogue is based on internationallyapplicable standards or standards common within the industry and exceeds theserequirements.∙The product has been tested in the laboratory according to these criteria.∙The keyword “Flicker Free” confirms that the device has no visible and invisibleflicker defined in this standard within the range of 0 - 3000 Hz under variousbrightness settings.∙The display will not support Flicker Free when Anti Motion Blur/MPRT is enabled.(The availability of Anti Motion Blur/MPRT varies by products.) ENERGY STAR CertificationENERGY STAR is a program run by the U.S. Environmental Protection Agency (EPA) and U.S. Department of Energy (DOE) to promote energy efficiency. This product qualifies for ENERGY STARin the “factory default” settings through which power savings will be achieved. Changing the factory default picture settings or enablingother features will increase power consumption, which could exceedthe limits necessary to qualify for ENERGY STAR rating.For more information on ENERGY STAR, refer to https:///.28TÜV Rheinland CertificationRegulatory NoticesCE ConformityThis device complies with the requirements set out in the Council Directive on the Approximation of the Laws of the Member Statesrelating to Electromagnetic Compatibility (2014/30/EU), Low-voltage Directive (2014/35/EU), ErP Directive (2009/125/EC) and RoHS directive (2011/65/EU). This product has been tested and found to comply with the harmonized standards for Information Technology Equipment published under Directives of Official Journal of the European Union.FCC-B Radio Frequency Interference StatementThis equipment has been tested and found to comply with the limitsfor a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, ifnot installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determinedby turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the measures listed below:∙Reorient or relocate the receiving antenna.∙Increase the separation between the equipment and receiver.∙Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.∙Consult the dealer or an experienced radio/television technician for help. Notice 1The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.Notice 2Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:1. This device may not cause harmful interference, and2. This device must accept any interference received, including interference that may cause undesired operation.MSI Computer Corp.901 Canada Court, City of Industry, CA 91748, USA(626) 913-082829Regulatory NoticesWEEE StatementUnder the European Union (“EU”) Directive on Waste Electrical and Electronic Equipment, Directive 2012/19/EU, products of “electrical and electronic equipment” cannot be discarded as municipal waste anymoreand manufacturers of covered electronic equipment will be obligated totake back such products at the end of their useful life. Chemical Substances InformationIn compliance with chemical substances regulations, such as the EU REACH Regulation (Regulation EC No. 1907/2006 of the European Parliament and the Council), MSI provides the information of chemical substances in products at: https:///global/indexRoHS StatementJapan JIS C 0950 Material DeclarationA Japanese regulatory requirement, defined by specification JIS C 0950, mandates that manufacturers provide material declarations for certain categories of electronic products offered for sale after July 1, 2006.https:///global/Japan-JIS-C-0950-Material-Declarations India RoHSThis product complies with the “India E-waste (Management and Handling) Rule 2016” and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for the exemptions set in Schedule 2 of the Rule. Turkey EEE RegulationConforms to the EEE Regulations of the Republic Of Turkey Ukraine Restriction of Hazardous SubstancesThe equipment complies with requirements of the Technical Regulation, approved by the Resolution of Cabinet of Ministry of Ukraine as of 10 March 2017, № 139, in terms of restrictions for the use of certain dangerous substances in electrical and electronic equipment.Vietnam RoHSAs from December 1, 2012, all products manufactured by MSI comply with Circular 30/2011/TT-BCT temporarily regulating the permitted limits for a number of hazardous substances in electronic and electric products.30Regulatory Notices31Regulatory Notices Green Product Features∙Reduced energy consumption during use and stand-by ∙Limited use of substances harmful to the environment and health∙Easily dismantled and recycled ∙Reduced use of natural resources by encouraging recycling ∙Extended product lifetime through easy upgrades ∙Reduced solid waste production through take-back policy Environmental Policy ∙The product has been designed to enable proper reuse of parts and recycling and should not be thrown away at its end of life. ∙Users should contact the local authorized point of collection for recycling and disposing of their end-of-life products. ∙Visit the MSI website and locate a nearby distributor for further recycling information. ∙*******************************************************************disposal, take-back, recycling, and disassembly of MSI products.Warning!Overuse of screens is likely to affect eyesight.Recommendations: 1. Take a 10-minute break for every 30 minutes of screen time. 2. Children under 2 years of age should have no screen time. For children aged 2 years and over, screen time should be limited to less than one hour per day.Copyright and Trademarks Notice Copyright © Micro-Star Int’l Co., Ltd. All rights reserved. The MSI logo used is a registered trademark of Micro-Star Int’l Co., Ltd. All other marks and names mentioned may be trademarks of their respective owners. No warranty as to accuracy or completeness is expressed or implied. MSI reserves the right to make changes to this document without prior notice.Technical Support If a problem arises with your product and no solution can be obtained from the user’s manual, please contact your place of purchase or local distributor. Alternatively,please visit https:///support/ for further guidance.。
LCD Monitor 程式设计理论
LCD 监视器程序设计理论VGA (显示卡)现在市面上的显示卡或笔记本 非常多,所以LCD 监视器 的兼容性格外重要,通常客户会做兼容性测试在LCD 监视器 设计研发的阶段,一般大约要测200至300张显示卡。
VESA 是支持并且确定PC ，工作站和民用电子工业的工业范围内的界面标准的一个组织。
VESA 促进并且发展及时，相关，公开的标准给那些显示并且展示工业界面，保证互操作性并且鼓励革新和发展市场。
VESA 定义了一些标准的Mode 从显示卡或者是有Graphic IC 的Device 输出，我们称之为Preset timing ，其组成有H freq(水平频率)、V freq(垂直频率)、RGB 数据的讯号。
Figure 1即是VESA Monitor Timing Spec Ver 1.0，定义了VESA Standard 的一些Timing 。
Figure 1.Figure2 为详细的800x600 60 Hz Timing，其中有很多参数定义如Pixel Rate、Htotal、H Display、Vtotal、V Display …等。
Figure 2.简单来说任何一组Timing 皆可看为一个窗口，水平的单位为pixel ，垂直的单位为line ，例如800x600 60Hz 的Timing ，即水平可视的有800个pixels ，垂直的有600个lines ，MST9151B是一种高性能并且整合性高的IC，其中整合了ADC(Analog-Digital Converter)、高质量的缩放技术、OSD (可供使用者操作的界面)、频率产生器…等，透过Firmware软件的控制，可让Scaler IC发挥它最大的性能，所以Firmware在整个研发设计中占有极重要的角色，一旦设计概念错误，不仅性能会不好，兼容性也会很差，Figure 3.即描述了Scaler的特色。
Figure 3.Firmware是烧录在8051架构的MCU里头，其中储存了VEGA Standard的Timing Table，一般又称为Mode Table，程序设计的理论如下：1．设定Scaler及周边IC初始值2．侦测是否有讯号进入Scaler3．查表(Search Mode Table)4．设定Capture window5．设定Display window6．设定使用者界面7．点亮背光模块虽然VESA Standard 定义了一些标准的Timing ，但是因为显示卡的种类非常多，所以程序的设计必须要可以考虑兼容性的问题，如果程序架构不好，可能有一些卡会不能显示。
PRO Series LCD Monitor PRO MP2412C (3PA9) 用户指南说明书
PRO Series LCD Monitor PRO MP2412C (3PA9)User GuideContentsGetting Started (3)Package Contents (3)Installing the Monitor Stand (4)Adjusting the Monitor (5)Monitor Overview (6)Connecting the Monitor to PC (7)OSD Setup (8)OSD Keys (8)OSD Menus (10)Luminance (10)Image Setup (11)Color Temp. (11)OSD Setup (12)Extra (12)Specifications (13)Preset Display Modes (15)Troubleshooting (16)Safety Instructions (17)TÜV Rheinland Certification (19)ENERGY STAR Certification (19)Regulatory Notices (20)RevisionV1.0, 2023/08Getting StartedThis chapter provides you with the information on hardware setup procedures. While connecting devices, be careful in holding the devices and use a grounded wrist strap to avoid static electricity.∙Contact your place of purchase or local distributor if any of the items is damaged or missing.∙Package contents may vary by country.∙The included power cord is exclusively for this monitor and should not be used with other products.Installing the Monitor Stand 1. Leave the monitor in its protective foam packaging. Align, insert and push the stand bracket towards the monitor groove until it locks in place.2. In case of improper installation, push the release tab to release and reinstall the stand.3. Connect the base to the stand and tighten the base screw to secure the base.4. Make sure the stand assembly is properly installed before setting the monitor Important ∙Place the monitor on a soft, protected surface to avoid scratching the display panel. ∙Do not use any sharp objects on the panel. ∙This product comes with NO protective film to be removed by the user! Any mechanical damages to the product including removal of the polarizing film may affect the warranty!Adjusting the MonitorThis monitor is designed to maximize your viewing comfort with its adjustment capabilities.⚠ImportantAvoid touching the display panel when adjusting the monitor.Monitor OverviewConnecting the Monitor to PC1. Turn off your computer.2. Connect the video cable from the monitor to your computer.3. Connect the power cord to the monitor power jack. (Figure A)4. Plug the power cord into the electrical outlet. (Figure B)5. Turn on the monitor. (Figure C)6. Power on the computer and the monitor will auto detect the signal source.OSD Setup⚠ImportantThis chapter provides you with essential information on OSD Setup.All information is subject to change without prior notice.OSD KeysThe monitor comes with a set of OSD Keys that help to control the On-Screen Display (OSD) menu.OSD Menus* Based on CIE1976 test standards.Preset Display Modes ImportantTroubleshootingThe power LED is off.• Press the monitor power button again.• Check if the monitor power cable is properly connected.No image.• Check if the computer graphics card is properly installed.• Check if the computer and monitor are connected to electrical outlets and are turned on.• Check if the monitor signal cable is properly connected.• The computer may be in Standby mode. Press any key to activate the monitor. The screen image is not properly sized or centered.• Refer to Preset Display Modes to set the computer to a setting suitable for the monitor to display.No Plug & Play.• Check if the monitor power cable is properly connected.• Check if the monitor signal cable is properly connected.• Check if the computer and graphics card are Plug & Play compatible. The icons, font or screen are fuzzy, blurry or have color problems.• Avoid using any video extension cables.• Adjust brightness and contrast.• Adjust RGB color or tune color temperature.• Check if the monitor signal cable is properly connected.• Check for bent pins on the signal cable connector.The monitor starts flickering or shows waves.• Change the refresh rate to match the capabilities of your monitor.• Update your graphics card drivers.• Keep the monitor away from electrical devices that may cause electromagnetic interference (EMI).Safety Instructions∙Read the safety instructions carefully and thoroughly.∙All cautions and warnings on the device or User Guide should be noted.∙Refer servicing to qualified personnel only.Power∙Make sure that the power voltage is within its safety range and has been adjusted properly to the value of 100~240V before connecting the device to the power outlet. ∙If the power cord comes with a 3-pin plug, do not disable the protective earth pin from the plug. The device must be connected to an earthed mains socket-outlet.∙Please confirm the power distribution system in the installation site shall provide the circuit breaker rated 120/240V, 20A (maximum).∙Always disconnect the power cord or switch the wall socket off if the device would be left unused for a certain time to achieve zero energy consumption.∙Place the power cord in a way that people are unlikely to step on it. Do not place anything on the power cord.∙If this device comes with an adapter, use only the MSI provided AC adapter approved for use with this device.Environment∙To reduce the possibility of heat-related injuries or of overheating the device, do not place the device on a soft, unsteady surface or obstruct its air ventilators.∙Use this device only on a hard, flat and steady surface.∙To prevent the device from tipping over, secure the device to a desk, wall or fixed object with an anti-tip fastener that helps to properly support the device and keep it safe in place.∙To prevent fire or shock hazard, keep this device away from humidity and high temperature.∙Do not leave the device in an unconditioned environment with a storage temperature above 60℃ or below -20℃, which may damage the device.∙The maximum operating temperature is around 40℃.∙When cleaning the device, be sure to remove the power plug. Use a piece of soft cloth rather than industrial chemical to clean the device. Never pour any liquid into the opening; that could damage the device or cause electric shock.∙Always keep strong magnetic or electrical objects away from the device.∙If any of the following situations arises, get the device checked by service personnel:• The power cord or plug is damaged.• Liquid has penetrated into the device.• The device has been exposed to moisture.• The device does not work well or you can not get it working according to the User Guide.• The device has dropped and damaged.• The device has obvious sign of breakage.ENERGY STAR Certification ENERGY STAR is a program run by the U.S. Environmental Protection Agency (EPA) and U.S. Department of Energy (DOE) to promote energy efficiency. This product qualifies for ENERGY STAR in the “factory default” settings through which power savings will be achieved. Changing the factory default picture settings or enabling other features will increase power consumption, which could exceed the limits necessary to qualify for ENERGY STAR rating. TÜV Rheinland CertificationTÜV Rheinland Low Blue Light Certification Blue light has been shown to cause eye fatigue and discomfort. MSI now offers monitors with TÜV Rheinland Low Blue Light certification to ensure users’ eye comfort and well-being. Please follow the instructions below to reduce the symptoms from extended exposure to the screen and blue light. ∙Place the screen 20 – 28 inches (50 – 70 cm) away from your eyes and a little below eye level.∙Consciously blinking the eyes every now and then will help to reduce eye strain after extended screen time.∙Take breaks for 20 minutes every 2 hours. ∙Look away from the screen and gaze at a distant object for at least 20 seconds during breaks. ∙Make stretches to relieve body fatigue or pain during breaks. ∙Turn on the optional Low Blue Light function.TÜV Rheinland Flicker Free Certification ∙TÜV Rheinland has tested this product to ascertain whether the display produces visible and invisible flicker for the human eye and therefore strains the eyes of users. ∙TÜV Rheinland has defined a catalogue of tests, which sets out minimum standards at various frequency ranges. The test catalogue is based on internationally applicable standards or standards common within the industry and exceeds these requirements. ∙The product has been tested in the laboratory according to these criteria. ∙The keyword “Flicker Free” confirms that the device has no visible and invisible flicker defined in this standard within the range of 0 - 3000 Hz under various brightness settings. ∙The display will not support Flicker Free when Anti Motion Blur/MPRT is enabled. (The availability of Anti Motion Blur/MPRT varies by products.)Regulatory NoticesCE ConformityThis device complies with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility (2014/30/EU), Low-voltage Directive (2014/35/EU), ErP Directive (2009/125/EC) and RoHS directive (2011/65/EU). This product has been tested and found to comply with the harmonized standards for Information Technology Equipment published under Directives of Official Journal of the European Union.FCC-B Radio Frequency Interference StatementThis equipment has been tested and found to comply with the limitsfor a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, ifnot installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the measures listed below:∙Reorient or relocate the receiving antenna.∙Increase the separation between the equipment and receiver.∙Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.∙Consult the dealer or an experienced radio/television technician for help. Notice 1The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Notice 2Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:1. This device may not cause harmful interference, and2. This device must accept any interference received, including interference that may cause undesired operation.MSI Computer Corp.901 Canada Court, City of Industry, CA 91748, USA(626) 913-0828WEEE StatementUnder the European Union (“EU”) Directive on Waste Electrical and Electronic Equipment, Directive 2012/19/EU, products of “electrical and electronic equipment” cannot be discarded as municipal waste anymoreand manufacturers of covered electronic equipment will be obligated totake back such products at the end of their useful life. Chemical Substances InformationIn compliance with chemical substances regulations, such as the EU REACH Regulation (Regulation EC No. 1907/2006 of the European Parliament and the Council), MSI provides the information of chemical substances in products at: https:///global/indexRoHS StatementJapan JIS C 0950 Material DeclarationA Japanese regulatory requirement, defined by specification JIS C 0950, mandates that manufacturers provide material declarations for certain categories of electronic products offered for sale after July 1, 2006.https:///global/Japan-JIS-C-0950-Material-Declarations India RoHSThis product complies with the “India E-waste (Management and Handling) Rule 2016” and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for the exemptions set in Schedule 2 of the Rule. Turkey EEE RegulationConforms to the EEE Regulations of the Republic Of Turkey Ukraine Restriction of Hazardous SubstancesThe equipment complies with requirements of the Technical Regulation, approved by the Resolution of Cabinet of Ministry of Ukraine as of 10 March 2017, № 139, in terms of restrictions for the use of certain dangerous substances in electrical and electronic equipment.Vietnam RoHSAs from December 1, 2012, all products manufactured by MSI comply with Circular 30/2011/TT-BCT temporarily regulating the permitted limits for a number of hazardous substances in electronic and electric products.Green Product Features∙Reduced energy consumption during use and stand-by∙Limited use of substances harmful to the environment and health∙Easily dismantled and recycled∙Reduced use of natural resources by encouraging recycling∙Extended product lifetime through easy upgrades∙Reduced solid waste production through take-back policy Environmental Policy∙The product has been designed to enable proper reuse of parts and recycling and should not be thrown away at its end of life.∙Users should contact the local authorized point of collection for recycling and disposing of their end-of-life products.∙Visit the MSI website and locate a nearby distributor for further recycling information.∙******************************************************************* disposal, take-back, recycling, and disassembly of MSI products. Warning!Overuse of screens is likely to affect eyesight. Recommendations:1. Take a 10-minute break for every 30 minutes of screen time.2. Children under 2 years of age should have no screen time. For children aged 2 years and over, screen time should be limited to less than one hour per day. Copyright and Trademarks NoticeCopyright © Micro-Star Int’l Co., Ltd. All rights reserved. The MSI logo used isa registered trademark of Micro-Star Int’l Co., Ltd. All other marks and names mentioned may be trademarks of their respective owners. No warranty as to accuracy or completeness is expressed or implied. MSI reserves the right to make changes to this document without prior notice.The terms HDMI™, HDMI™ High-Definition Multimedia Interface, HDMI™ Trade dress and the HDMI™ Logos are trademarks or registered trademarks of HDMI™ Licensing Administrator, Inc.Technical SupportIf a problem arises with your product and no solution can be obtained from the user’s manual, please contact your place of purchase or local distributor. Alternatively, please visit https:///support/ for further guidance.。
LCD MONITOR架构详细讲解(doc 8页)
更多资料请访问.(.....)资料整理：单位：RD-PE LCD 审查；核 准： 日 期：MAR-10-02LCD MONITOR 架构讲解一、 LCD 整机框图：Convert DC 12V AC 1500～1800V HV( at 30～50KHZwith 5～9 mA)二、 INVERTER 部分INVERTER 即升压板(变压器)，是DC 转AC 升压电路。
它将Main Board 上送入12V 直流供电转换成1500～1800V 的高压交流电，频率30～50KHZ ，电流5～9mA 。
（以上数值因PANLE 特性的差异而不同）PANEL 灯管在电源的作用下被点亮，1500～1800V 的交流电持续1～2S 降至400～600V 的稳定电压(设计时环境温度以0℃为准)。
INVERTER 提供的电流大小影响灯管寿命，INVERTER 提供电压变化曲线如图所示： V oltage （V附1：T541 IBM 自制INVERTER 电路图 三、 ADAPTER 部分ADAPTER 即电源适配器，是将90～240V 的交流电转换为12V （或14V ）的直流稳定电压供给主板工作。
其工作原理同CRT MONITOR POWER 部分。
附2：T541 IBM ADPC7803A 自制ADAPTER 电路图。
四、 MAIN BOARD 部分MAIN BOARD 由PANEL 控制逻辑、亮度控制逻辑、DDC``控制逻辑、DC-DC 转换逻辑、传输TTL 、电平信号到LCD 显示电路组成。
MAIN BOARD 结构图：（1） MAIN BOARD 主要IC 描述：（以LM-500为例）1、 GMZAN1（集成ADC 、OSD 、SCALER AND INTERPOLATION ）把计算机R/G/B 模拟图象信号转换为数字信号，通过差补缩放处理，输出至LCD-PANEL 时序控制电路； 2、 MCU 作用：RS232通讯、频率计算、检测CHANGE MODE 、电源控制、OSD 控制； 3、 24LC21：MICROCHIP IC 1KB EEPROM ，用于存储DDC 数据；4、 24C04：A TMEL IC EEPROM ，4KB ，用于存储AUTO-CONFIG 数据、白平衡数据、POWER KEY 状态、POWER ON 记数数据； 5、 LM22596电源变换：12V 5V （3A ） 6、 AIC1048-33CM 电源变换：5V 3.3V （2） PANEL 控制逻辑：CONTROL SIGNAL1、 DCLK ：DISPLAY CLOCK 工作频率30MHZ ～40MHZ （15”）、50MHZ ～65MHZ（17”）之间。
Philips LCD Monitor 电子用户手册.pdf_1718559405.4528391说
Safety and Troubleshooting Information•安全措施及维修• 常见问题• 故障检修• 有关规定• 其他相关信息安全和故障检修安全措施与维修警告：使用本文件规定以外的控制、调整或程序，可能导致遭受电击、触电以及/或者机械危险。
连接和使用电脑显示器时，请阅读并遵循以下说明：操作：● 不要让显示器受阳光直接照射，并使其远离火炉或其它任何热源。
● 移开任何可能掉入通风孔的物品或者会妨碍显示器电子器件正常冷却的物品。
● 不要堵塞机壳上的通风孔。
● 放置显示器时，确保电源插头和插座便于插拔。
● 如果通过拔掉电源线或直流电源线关闭显示器电源，则在重新连接电源线或直流电源线以进行正常操作之前，必须等待 6 秒钟。
● 请务必使用由 Philips 提供的经过认可的电源线。
如果电源线缺失，请与您当地的服务中心联系。
（请参见“消费者信息中心”）● 在使用过程中，不要让 LCD 显示器遭受剧烈震动或冲击。
● 在使用或运输期间，不要敲打显示器或使显示器掉落。
维护：● 为保护显示器不受破坏，不要过分用力按压 LCD 面板。
移动显示器时，抓住边框将其抬起；抬起时，不要将手或手指放在 LCD 面板上。
● 长时间不使用显示器时，应拔掉显示器电源插头。
● 使用略微蘸湿的布清洁显示器时，应拔掉显示器电源线插头。
电源关闭时，可以使用干布擦拭屏幕。
但是，切勿使用有机溶剂（如酒精）或含氨水的液体清洁显示器。
● 为避免电击或本机永久性损坏，不要在多尘、下雨、水附近或过分潮湿的环境中使用显示器。
● 如果显示器被弄湿了，应尽快用软布擦拭干净。
● 如果异物或水进入显示器，请立即关闭电源，并拔掉电源线。
然后，取出异物或擦干水，并送到维修中心进行检修。
● 不要在靠近热源、阳光直射或过分寒冷的场所存放或使用 LCD 显示器。
● 为了保持显示器的最佳性能并延长使用寿命，请在符合下列温度和湿度条件的地方使用显示器。
r温度：5-35°C 41-95°Fr湿度：20-80% RHfile:///D|/My%20Documents/dfu/200W6/china/200w6/safety/safety.htm (1 of 2)2005-06-28 1:56:10 PMSafety and Troubleshooting Information维修：● 只有专业的维修人士可以打开机壳盖。
ASUS VG2491R Series LCD Monitor用户指南说明书
iiCopyright © 2020 ASUSTeK COMPUTER INC. All Rights Reserved.No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing.ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringeTable of contentsNotices .........................................................................................................iii Care & Cleaning . (v)1.1Welcome! ......................................................................................1-11.2Package contents .........................................................................1-11.3Assembling the monitor ..............................................................1-21.4Outline dimension ........................................................................1-21.5Connect cables .............................................................................1-31.5.1 Rear of the LCD monitor .................................................1-31.6Monitor introduction ....................................................................1-41.6.1 Using the Controls button ..............................................1-42.1Detaching the arm/stand (for wall mount) ................................. 2-12.2Adjusting the monitor ..................................................................2-23.1 OSD (On-Screen Display) menu .................................................3-13.1.1 How to reconfigur ..........................................................3-13.1.2 OSD Function Introduction ..............................................3-23.2 Specification .............................................................................3-113.3 Troubleshooting (FAQ) ..............................................................3-123.4Supported Timing List ...............................................................3-13NoticesFederal Communications Commission StatementThis device complies with Part 15 of the FCC Rules. Operation is subjectto the following two conditions:•This device may not cause harmful interference, and•This device must accept any interference received includinginterference that may cause undesired operation.This equipment has been tested and found to comply with the limits fora Class B digital device, pursuant to Part 15 of the FCC Rules. Theselimits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, usesand can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference willnot occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correctthe interference by one or more of the following measures:•Reorient or relocate the receiving antenna.•Increase the separation between the equipment and receiver.•Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.•Consult the dealer or an experienced radio/TV technician for help. Canadian Department of Communications StatementThis digital apparatus does not exceed the Class B limits for radionoise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.This class B digital apparatus complies with Canadian ICES-003.iiiSafety information•Before setting up the monitor, carefully read all the documentation that came with the package.•To prevent fire or shock hazard, never expose the monitor to ra n or moisture.•Never try to open the monitor cabinet. The dangerous high voltages inside the monitor may result in serious physical injury.•If the power supply is broken, do not try to fix it by yourself Contact a qualifie service technician or your retailer.•Before using the product, make sure all cables are correctly connected and the power cables are not damaged. If you detect any damage, contact your dealerimmediately.•Slots and openings on the back or top of the cabinet are provided for ventilation. Do not block these slots. Never place this product near or over aradiator or heat source unless proper ventilation is provided.•The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supply to your home,consult your dealer or local power company.•Use the appropriate power plug which complies with your local power standard.•Do not overload power strips and extention cords. Overloading can result in fir or electric shock.•Avoid dust, humidity, and temperature extremes. Do not place the monitor in any area where it may become wet. Place the monitor on a stable surface.•Unplug the unit during a lightning storm or if it will not be used for a long period of time. This will protect the monitor from damage due to power surges.•Never push objects or spill liquid of any kind into the slots on the monitor cabinet.•If you encounter technical problems with the monitor, contact a qualified service technician or your retailer.•Adjustment of the volume control as well as the equalizer to other settings than the center position may increase the ear-/headphones output voltage andtherefore the sound pressure level.•The adapter is only used for this monitor, do not use it for other purpose.•Please make sure to connect the adapter to main socket with protective earthing. Your device uses one of the following power supplies:Manufacturer: Delta Electronics Inc., Model: ADP-40KD BBThis symbol of the crossed out wheeled bin indicates that the product (electrical,electronic equipment, and mercury-containing button cell battery) should notbe placed in municipal waste. Please check local regulations for disposal ofelectronic products.ivvWARNINGUsage of other than specifie head- or earphones can result in hearing loss due to excessive sound pressures.Care & Cleaning•Before you lift or reposition your monitor, it is better to disconnect the cables and power cord. Follow the correct lifting techniques when positioning the monitor. When lifting or carrying the monitor, grasp the edges of the monitor. Do not lift the display by the stand or the cord.•Cleaning. Turn your monitor off and unplug the power cord. Clean the monitor surface with a lint-free, non-abrasive cloth. Stubborn stains may be removed with a cloth dampened with mild cleaner.•Avoid using a cleaner containing alcohol or acetone. Use a cleaner intended for use with the LCD. Never spray cleaner directly on the screen, as it may drip inside the monitor and cause an electric shock.The following symptoms are normal with the monitor:•The screen may flicker during the initial use due to the nature of the fluorescent light. Turn off the Power Switch and turn it on again to make sure that the flicker disappears.•You may find slightly uneven brightness on the screen depending on the desktop pattern you use.•When the same image is displayed for hours, an afterimage of the previous screen may remain after switching the image. The screen will recover slowly or you can turn off the Power Switch for hours.•When the screen becomes black or flashes, or cannot work anymore,contact your dealer or service center to fix it. Do not repair the screen by yourself!Conventions used in this guideWARNING: Information to prevent injury to yourself when trying tocomplete a task.CAUTION: Information to prevent damage to the componentswhen trying to complete a task.IMPORTANT: Information that you MUST follow to complete atask.NOTE: Tips and additional information to aid in completing a task.Where to fin d more informationRefer to the following sources for additional information and forproduct and software updates.1.ASUS websitesThe ASUS websites worldwide provide updated information on ASUShardware and software products. Refer to 2.Optional documentationYour product package may include optional documentation that mayhave been added by your dealer. These documents are not part ofthe standard package.Takeback ServicesASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions forour customers to be able to responsibly recycle our products, batteries and other components as well as the packaging materials.Please go to /english/Takeback.htm for detail recyclinginformation in different region.vi1-1ASUS LCD Monitor VG2491R Series 1.1 Welcome!Thank you for purchasing the ASUS ® LCD monitor!The latest widescreen LCD monitor from ASUS provides a crisper, broader, and brighter display, plus a host of features that enhance your viewing experience.With these features, you can enjoy the convenience and delightful visual experience that the monitor brings you!1.2 Package contentsCheck your package for the following items:LCD MonitorMonitor BaseQuick Start GuideWarranty Card1x Power Cord1x Power adapter1x HDMI Cable (optional)1x DisplayPort Cable (optional)•If any of the above items is damaged or missing, contact your retailer immediately.1-2Chapter 1: Product Introduction1.3Assembling the monitor To assemble the monitor:1.2.Adjust the monitor to the angle that is most comfortable for you.1.4 Outline dimensionUnit: mm [inch]-5 ~ 22Place the display flat on a cloth on the table, Then attach the base to the arm and f ix with the screw to join them tightly. You can easily tighten the screw byfingers.1.5 Connect cables1.5.1 Rear of the LCD monitor1.DC-IN Port2.Audio - out Port3.HDMI 2 Port4.HDMI 1 Port5.DisplayPort PortASUS LCD Monitor VG2491R Series1-31-4Chapter 1: Product Introduction1.Power Indicator:•5.Up key:•Use this hotkey to GamePlus.6.Down key :•Use this hotkey to GameVisual.2.Central button:•Press this button to enter the OSD menu.•Press this button to turn on the monitor when turned off.3.Left key:•Exit the OSD menu or return to the previous layer.4.Right key:•Power Off shortcut key.•Enter the option of the next layer.•Move the option upwards or increase the option value.•Move the option downwards or decrease the option value.•Key Lock shortcut key. Press and hold it for 5 seconds to enable/disable Keys Lock.GamePlus Function•Press GamePlus Button to enter the GamePlus main menu.•Activate Crosshair, Timer or FPS Counter or Display Alignmentfunction.•Press the ❑ and ☐ buttons to select and press to confirm thefunction needed. Press to go off, and exit.•ASUS LCD Monitor VG2491R Series1-5GameVisual FunctionThe GameVisual function helps you select among different picture modes in aconvenient way.To active GameVisual:Press the GameVisual hotkey repeatedly to select.•Scenery Mode: This is the best choice for scenery photo displaying withGameVisual TM Video intelligence Technology.•Racing Mode: This is the best choice for racing game playing withGameVisual TM Video intelligence Technology.•Cinema Mode: This is the best choice for movie watching withGameVisual TM Video intelligence Technology.•RTS/RPG Mode: This is the best choice for Real-Time Strategy (RTS)/Role-Playing Game (RPG) playing with GameVisual TM Video intelligenceTechnology.•FPS Mode: This is the best choice for First Person Shooter game playingwith GameVisual TM Video intelligence Technology.•sRGB Mode: This is the best choice for viewing photos and graphicsfrom PCs.•MOBA Mode: This is the best choice for multiplayer online battle arenagame playing with GameVisual TM Video intelligence Technology.Saturation, Skin Tone, ASCR.•In the sRGB mode, the following function(s) are not user-configurable:Brightness, Contrast, Saturation, Color Temp., Skin Tone, ASCR.•In the MOBA mode, the following function(s) are not user-configurable:Saturation, Skin Tone, ASCR.1-6Chapter 1: Product Introduction2-1ASUS LCD Monitor VG2491R Series 2.1Detaching the arm/stand (for wallmount)（wall mount only for HDMI Port ）The detachable stand of this monitor is specially designed for wall mount.To detach the arm/stand 1.Disconnect power and signal cables. Carefully put the front of the monitor face down on a clean table.2.Use a screwdriver to remove the two screws on the arm (Figure 1),and then detach the arm/stand from the monitor (Figure 2).•We recommend that you cover the table surface with soft cloth to prevent damage to the monitor.•Hold the stand of the monitor while removing the screws.Figure 1•The wall mount kit ( 75 x 75 mm) is purchased separately.•Use only the UL Listed Wall Mount Bracket with minimum weight/load 12 kg (Screw size: M4 x 10 mm).2-2Chapter 2: Setup2.2Adjusting the monitor•For optimal viewing, we recommend that you look at the full face of the monitor, then adjust the monitor to the angle that is most comfortable for you.•Hold the stand to prevent the monitor from falling when you change its angle.•You can adjust the monitor’s angle from +22˚ to -5˚.It is normal that the monitor slightly shakes while you adjust the viewing angle.-5 ~223-1ASUS LCD Monitor VG2491R Series 3.1OSD (On-Screen Display) menu3.1.1How to reconfigur1.Press the MENU button to activate the OSD menu.2.Press the ❑ and ☐ buttons to toggle between options in theMenu. As you move from one icon to another, the option name is highlighted.3.To select the highlighted item on the menu press the button.4.Press the ❑ and ☐ buttons to select the desired parameter.5.Press the button to enter the slide bar and then use the ❑ or ☐buttons, according to the indicators on the menu, to make your changes.6.Select the to return to previous menu or to accept and return to previous menu.•••3.1.2 OSD Function Introduction 1.Gam ingOD(Tracefree): Improves the gray level response time of the LCD panel.This function is not available when ELMB is enabled.•Adaptive-Sync/FreeSync Premium:Allows an FreeSync Premium(Adaptive-Sync)supported graphics source to dynamically adjustdisplay refresh rate based on typical content frame rates for powerefficient, virtually stutter free and low-latency display update.•Adaptive-Sync/FreeSync Premium can only be activated within48Hz~165Hz for DisplayPort.•For supported GPUs, minimum PC system and driver requirements,please contact the GPU manufactures.•When FreeSync Premium is Off, this function can only beactivated when the refresh rate is 100Hz, 120Hz, 144Hz or 165Hz.•GamePlus: See 1.6.1 GamePlus.Function for details.GameVisual: See 1.6.1 GameVisual.Functionfor details.•FreeSync Premium can only be activated within48Hz~144Hz for HDMI .•.Overclocking:*.ON: This function allows you to adjust the refresh rate.*.Max.Refresh.Rate: Allows you to select a maximum refresh rateof165Hz (Only for DisplayPort input). After selecting,press the button to activate the setting.Overclocking may cause screen flickering. To reduce such effects, disconnectthe DisplayPort cable and use the monitor OSD menu to try again with a saferMax. Refresh rate.•ELMB: &KHFN WR GHFUHDVH PRWLRQ EOXU DQG PLQLPL]H JKRVWLQJ SDUW ZKHQRQ VFUHHQ REMHFWV DUH IDVW PRYLQJ3-2Chapter 3: General Instruction3-3ASUS LCD Monitor VG2491R Series 2.Image•Brightness : The adjusting range is from 0 to 100.•Contrast : The adjusting range is from 0 to 100.•VividPixel: Enhances the outline of the displayed picture and generates high-quality images on screen.•ASCR : Turns on/off the ASCR (ASUS Smart Contrast Ratio) function.•Aspect Control : Adjusts the aspect ratio to Full , or 4:3•Blue Light Filter *Level 0: No change.*Level 1~4: The higher the level, the less blue light is scattered.When Blue Light Filter is activated,the default settings of Racing Mode will be automatically imported. Between Level 1 to Level 3,the Brightness function is user-configurable. Level 4 is optimized setting. It is compliance with TUV Low Blue Light Certification.The Brightness function is not user-configurable.•Shadow Boost : Dark color enhancement adjusts monitor gamma curveto enrich the dark tones in an image, making dark scenes and objects much easier to be seen.This function is only available in Racing mode, RTS/RPG mode, FPS mode, or sRGB mode.3-4Chapter 3: General Instruction3.ColorSet a desired color setting from this menu.•Color Temp : Contains 4 modes including Cool, Normal, Warm, and User Mode.•Saturation : the adjusting range is from 0 to 100.•Skin Tone : Contains three color modes including Reddish, Natural, and Yellowish.4.Input SelectIn this function, you can select your desired input source.Please refer to the following to alleviate eye strains:•Users should take some time away from the display if working for long hours. It is advised to take short breaks (at least 5 mins) after around 1hour of continuous working at the computer. Taking short and frequent breaks is more effective than a single longer break.•To minimize eye strain and dryness in your eyes, users should rest the eye periodically by focusing on objects that are far away.•Eye exercises can help to reduces eye strain. Repeat these exercises often. If eye strain continues please consult a physician. Eye exercises: (1)Repeating look up and down (2) Slowly roll your eyes (3) Move your eyes diagonal.•High energy blue light may lead to eye strain and AMD (Age-Related Macular Degeneration). Blue light Filter to reduce 70% (max.) harmful blue light to avoiding CVS (Computer Vision Syndrome).3-5ASUS LCD Monitor VG2491R Series 5..MyFavorite•.Shortcut :*.Shortcut.1/Shortcut.2: Sets the shortcut functions for shortcut buttons.When a certain function is selected or activated, your shortcut button may not support. Available function choices for shortcut: GamePlus (only for Shortcut. 1), GameVisual (only for Shortcut.2), Brightness, Contrast, Blue Light Filter, Color Temp., Volume.•.Customized.Setting : Loads/Saves all settings on the monitor.6..System.Setup.•.Language : There are 21 languages for your selection, including English,French, German, Italian, Spanish, Dutch, Portuguese, Russian, Czech,Croatian, Polish, Romanian, Hungarian, Turkish, Simplified Chin se,Traditional Chinese, Japanese, Korean, Thai, Indonesian, Persian.•.Sound : Sets the sound related settings from this menu.*.Volume : The adjusting range is from 0 to 100.*.Mute : Toggles the monitor sound between on and off.•.ECO.Mode : reduces power consumption.•.Power.Indicator : Turn the power LED indicator on/off.•.Power.Key.Lock: Enables or disables the power key.•.Key.Lock: To disable all function keys. Press over 5 seconds to cancel the key lock function.•.OSD.Setup:*Adjusts the OSD timeout from 10 to 120 seconds.*Enables or disables the DDC/CI function.*Adjusts the OSD background from opaque to transparent.•.Information: Shows the monitor information.•.All.Reset: “Yes” allows you to restore the default settings.3-6Chapter 3: General Instruction3.2 Specification3.3 Troubleshooting (FAQ)3.4 Supported Timing List. Note:.You.must.select.one.of.the.“*”patibleGPU.graphic.card.。
I1601C LCD Monitor 用户手册说明书
LCD Monitor User Manual I1601C LED backlightSafety (3)National Conventions (3)Installation (4)Cleaning (5)Other (6)Setup (7)Contents in Box (7)Adjusting Viewing Angle (8)Connecting the Monitor (9)Adjusting (10)Hotkeys (10)OSD Setting (11)Driver (12)i-Menu (12)e-Saver (13)Screen+ (14)Troubleshoot (15)Specification (16)General Specification (16)Preset Display Modes (18)Plug and Play (19)SafetyNational ConventionsThe following subsections describe notational conventions used in this document.Notes, Cautions, and WarningsThroughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These blocks are notes, cautions, and warnings, and they are used as follows:NOTE: A NOTE indicates important information that helps you make better use of your computer system.CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.WARNING: A WARNING indicates the potential for bodily harm and tells you how to avoid the problem. Some warnings may appear in alternate formats and may be unaccompanied by an icon. In such cases, the specific presentation of the warning is mandated by regulatory authority.InstallationDo not place the monitor on an unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can injure a person and cause serious damage to this product. Use only a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with this product. Follow the manufacturer’s instructions when installing the product and use mounting accessories recommended by the manufacturer. A product and cart combination should be moved with care.Never push any object into the slot on the monitor cabinet. It could damage circuit parts causing a fire or electric shock. Never spill liquids on the monitor.Do not place the front of the product on the floor.Leave some space around the monitor as shown below. Otherwise, air-circulation may be inadequate hence overheating may cause a fire or damage to the monitor.See below the recommended ventilation areas around the monitor when the monitor is installed with the stand: Installed with standCleaningClean the cabinet regularly with cloth. You can use soft-detergent to wipe out the stain, instead ofstrong-detergent which will cauterize the product cabinet.When cleaning, make sure no detergent is leaked into the product. The cleaning cloth should not be too rough as it will scratch the screen surface.Please disconnect the power cord before cleaning the product.OtherIf the product is emitting a strange smell, sound or smoke, disconnect the power plug IMMEDIATELY and contact a Service Center.Make sure that the ventilating openings are not blocked by a table or curtain.Do not engage the LCD monitor in severe vibration or high impact conditions during operation.Do not knock or drop the monitor during operation or transportation.For display with glossy bezel the user should consider the placement of the display as the bezel may cause disturbing reflections from surrounding light and bright surfaces.SetupContents in BoxMonitorCD Manual Smart Cover USB Type-c cableAdjusting Viewing AngleFor optimal viewing, it is recommended to look at the full face of the monitor, and then adjust the monitor's angle to your own preference.Hold the Smart Cover and Monitor so you will not topple the monitor when you change the monitor's angle.You are able to adjust the monitor's angle from 5° to 25 °.NOTE:1. Do not adjust the viewing angle over 5~25 degrees in order to avoid damage.2. Hold the Smart Cover and Monitor so you will not topple the monitor when you change the monitor's angle.3. Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen.AOC I1601C monitor supports an auto-pivot function to keep the display upright as the monitor is rotated between portrait and landscape position.Important: Install I-MENU(Version 2.0 or upper) from CD-ROM or AOC website.Connecting the Monitor1 Power Button2 USB Type-CTo protect equipment, always turn off the PC and LCD monitor before connecting.1. Connect one end of the USB cable to the USB Monitor and the other end ofUSB cable to the computer.2. Your computer should detect the USB Monitor automatically.If your monitor displays an image, installation is complete. If it does not display an image, please refer Troubleshooting.AdjustingHotkeys1 Power /Menu/IncreasePower/Menu/IncreaseWhen Power off, press button to turn on the monitor.When Power on, press button to display OSD or navigate towards the right direction. When Power on, press button continuously about 3 seconds to turn off the monitor.OSD SettingBasic and simple instruction on the control keys.1).Press the bottom key to activate the OSD window.2). You can now select any one of the functions by quickly repeat-pressing the bottom key . The blue box will navigate towards the right as you press the key. You can release once the blue box highlights the option you want to choose. Note that the selection is one way loop always moving one direction and then returning at beginning of the menu. The blue box will remain on the selected function for about 3 seconds and the function icon will flash three times to confirm the choice visible on the 1st layer of the OSD and activate it.Brightness 0-100 Adjust brightness from 0~100Contrast 0-100 Adjust contrast from 0~100Overdrive WeakAdjust the response time. MediumStrongOffLowBlue Mode WeakDecrease blue light wave bycontrolling color temperature MediumStrongOffLanguage English, France, Spanish,Portuguese, German,Italian, Dutch, Swedish, Finnish, Polish, Czech, Russia, Korea, T Chinese,S Chinese, Japanese. Select the OSD language Default is English.Exit Exit the main OSD1. Main menu will disappear if no action for about 3 seconds..2. Sub menu will disappear if no action for about 3 seconds..3. Before entering OSD menu,monitor will be powered off when continually pressing the buttom key for more than3 seconds.Driveri-MenuWelcome to “i-Menu” software by AOC. i-Menu makes it easy to adjust your monitor display setting by using on screen menus instead of the OSD button on the monitor. To complete installation, please follow the installation guide.e-SaverWelcome to use AOC e-Saver monitor power management software! The AOC e-Saver features Smart Shutdown functions for your monitors, allows your monitor to timely shutdown when PC unit is at any status (On, Off, Sleep or Screen Saver); the actual shutdown time depends on your preferences (see example below).Please click on "driver/e-Saver/setup.exe" to start installing the e-Saver software, follow the install wizard to complete software installation.Under each of the four PC status, you may choose from the pull-down menu the desired time (in minutes) you’re your monitor to automatically shut down. The example above illustrated:1) The monitor will never shutdown when the PC is powered on.2) The monitor will automatically shutdown 5 minutes after the PC is powered off.3) The monitor will automatically shutdown 10 minutes after the PC is in sleep/stand-by mode.4) The monitor will automatically shutdown 20 minutes after the screen saver appears.You can click “RESET” to set the e-Saver to its default settings like below.Screen+Welcome to “Screen+” software by AOC. Screen+ software is a desktop screen splitting tool; it splits the desktop into different panels, and each panel displays a different window. You only need to drag the window to a corresponding panel when you want to access it. It supports multiple monitor display to make your task easier. Please follow the installation software to install it. The software Supported operating systems: Windows 10，Windows 8,Windows 7.TroubleshootThis section provides tips for correcting problems, should any occur. It also describes how to contact AOC should you encounter problems that you cannot resolve. Before you call AOC service center, please read the troubleshooting advice in this manual and in your computer User's Manual. You may also want to consult with your system administrator or company technical support staff.Specification General SpecificationPS: I1601C only as a display device.Compatible with all DP Alt mode PC or Laptop: Recommend list is as the below.Preset Display ModesPlug and PlayPlug & Play DDC2B FeatureThis monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities.The DDC2B is a bi-directional data channel based on the I2C protocol. The host can request EDID information over the DDC2B channel.。
LCD-monitor结构设计指南
LCD Monitor结构设计指南一、LCD Monitor 组成图1-1结构部分通常主要分成五大部件：面框后壳主固定板底座与支架，转轴按键有时还会有装饰件。
以及包装设计，ID label设计。
二、整体设计准备首先要根据市场部（或企业划部）提供的产品企划书，完全了解客户的整体要求。
✧确定pane 规格、外型尺寸、锁附位置。
✧power、A/D板尺寸、高位器件尺寸、安全距离、接口位置，锁附孔位置。
✧确定按键板的位置、大小，行程。
✧确定LED灯的位置。
✧检讨外形尺寸：✧整体设计和装配：前框与后壳：通常LCD Monitor 的结构设计前后壳采用卡扣(snap)的连接，底部有时辅助2-4颗螺钉（一般分布在，左下角1颗，右下角1颗，靠近转轴部分1-2颗）增强连接，同时也方便拆卸。
Panel装配：通过后壳或铁盘固定，（前框增加guide ribs定位panel上、下、左、右四个方向，以避免panel与前框的开口有偏差、避免露panel边铁以及倾斜的发生）。
铁盘装配：通过螺钉固定在转轴上，同时在后壳上给铁盘增加定位销或增加上、下、左、右四个方向的guide ribs。
支架与底座装配：通常建议采用卡扣连接（减少包装尺寸，对用户而言可以免工具拆装）。
如果有可能支架也能与底座一起拆装，方便继续减小包装尺寸。
转轴：转轴通常与底座通过螺钉连接，整体装配后锁附到后壳上。
Lips(电源板)与A/D板：固定在铁盘上,铁盘开孔散热。
按键：采用悬臂式结构设计使塑料排键有弹性。
通过螺钉或卡扣固定在前框或者后壳上。
三、3D建模结构设计之前需要将ID 部门（或外部设计公司的）所作的2D 效果图(2D sketch)立体化，实体化。
（这一步有可能在设计公司已经做好了）。
这个过程我们称之为PID 建模过程，建成的3D Pro/E 数据称为master。
这个3D 数据包含了所有ID 想要的曲线和曲面，分型线和美工线，甚至外表面的拔模角度，以及所有外观部件的拆分。
LCD Monitor 结构设计模块化与标准化
抽孔铆合数据图
项次序号
料厚T (mm)
抽高H (mm)
抽孔外径D(mm)
3.0
337.92
274
341.6
130.5±0.3
130.5±0.3
120±0.3
120±0.3
9.1±0.3
9.1±0.3
358.5±0.5
296.5±0.5
17±0.5
CPT
CLAA170EA07
270.336
337.92
274
341.6
130.5±0.3
130.5±0.3
120±0.3
120±0.3
2.增设加强肋,肋根部厚度≤0.5 T.
3.咬花:塑件表面腐蚀雕刻俗称咬花,它是一种以酸性化学药品浸蚀模具表面蚀刻出需求的花纹而得.各式各样的纹路植刻于金属表面的一种特殊加工工艺.LCD外壳塑件也广泛应用到咬花处理.下表列出了不同咬花对应的拔模角度标准.
说明：咬花类型和具体位置一般由客户指定
咬花深度越大，拔模角需要越大。
20±0.5
SAMSUNG
LTM190E1
301.056
376.32
305.1
380.3
87±0.3
87±0.3
96±0.3
96±0.3
8.5±0.3
8.5±0.3
404.2±0.5
330±0.5
20±0.5
AU
M190EN04
301.06
LG IPS LED监显器（LED LCD监显器）用户指南 19MB35P 22MB35P 23MB
OWNER’S MANUALIPS LED MONITOR (LED LCD MONITOR)19MB35P 22MB35P 23MB35PPlease read this manual carefully before operating your set and retain it for future reference.IPS LED(LED LCD) MONITOR MODEL ENGLISH2TABLE OF CONTENTS CONTENTS3ASSEMBLING AND PREPAR-ING3 Unpacking4 Parts and buttons5 Setting up the Monitor set5 - Attaching the Stand Base5 - Detaching the stand base6 - Detaching the stand body7 - Mounting on a table7 - Adjusting the angle8 - Adjusting the stand height8 - Using the Kensington locking device9 - Swivel stand9 - Using the Pivot function10 - Mounting on a wall11USING THE MONITOR SET 11 Connecting to a PC11 - D-SUB connection11 - DVI-D connection13CUSTOMIZING SETTINGS 14 Customizing Settings14 - Menu Settings15 - P icture16 - C olor17 - D isplay18 - O thers19 READER Setting20 - S UPER ENERGY SAVING21TROUBLESHOOTING 23SPECIFICATIONS23 19MB35P24 22MB35P25 23MB35P26 Preset Modes (Resolution)26 Indicator27PROPER POSTURE27 Proper posture for using the Monitor set.3ASSEMBLING AND PREPARINGASSEMBLING AND PREPARINGUnpackingCheck your product box for the following items. If there are any missing accessories, contact the localdealer where you purchased your product. The illustrations in this manual may differ from the actual product and accessories.5ASSEMBLING AND PREPARINGSetting up the Monitor setAttaching the Stand Base1 Place the Monitor set with the screen sidedown on a flat and cushioned surface.Detaching the stand base1 Place the monitor's screen face down.To protect the screen from scratches, cover thesurface with a soft cloth.2 Using a coin, turn the screw in the stand basecounterclockwise. Detach the stand base from the stand body .6ASSEMBLING AND PREPARINGDetaching the stand body1Place the monitor's screen face down. To protect the screen from scratches, cover the surface with a soft cloth.2Using a screwdriver, remove the four screws and detach the stand from the monitor.7ASSEMBLING AND PREPARING Adjusting the angle1Place the monitor mounted on the stand base in an upright position.2Adjust the angle of the screen. The angle ofMounting on a table1Lift the monitor and place it on the table in anupright position.Install at least 10 cm away from the wall toensure sufficient ventilation.23Press the (Power) button on the front of themonitor to turn on the monitor.Front Side Connect the Power cord to the monitor, thenplug the power cord into the wall outlet.8ASSEMBLING AND PREPARINGUsing the Kensington lockingdeviceThe connector for the Kensington lock is located on the rear of the monitor.For more information on installation and usage, refer to the Kensington lock user manual or visit the website at .Connect the monitor to the table with the Kensing-ton lock cable.Adjusting the stand height1 Place the monitor mounted on the stand basein an upright position.2 Remove the tape attached at the bottom rearof the stand body, then pull out the locking pin .Stand Body9ENG ENGLISHASSEMBLING AND PREPARINGSwivel standy Image shown may differ from your Monitor set.1 Swivel 355 degrees and adjust the angle of theMonitor set to suit your view.1 Lift the monitor to its highest height to utilizethe Pivot function.Using the Pivot functionThe pivot function allows you to rotate the screen90 degrees clockwise.2 Landscape & Portrait : You can rotate the panel90° clockwise. Please be cautious and avoid contact between the monitor head and theStand Base when rotating the screen to access the Pivot function. If the monitor head touches the Stand Base, then the Stand Base could crack.Head sectionStand section3 Be careful with the cables when rotating thescreen.10ASSEMBLING AND PREPARINGMounting on a wallFor proper ventilation, allow a clearance of 10 cmon each side and from the wall. Detailedinstructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and Setup Guide.If you intend to mount the Monitor set to a wall, attach Wall mounting interface (optional parts) to the back of the set.When you install the Monitor set using a wall mounting interface (optional parts), attach it carefully so it will not drop.1 Please, Use the screw and wall mount interfacein accordance with VESA Standards.2 If you use screw longer than standard, themonitor might be damaged internally.3 If you use improper screw, the product might bedamaged and drop from mounted position. In this case, LG Electronics is not responsible for it.4 VESA compatible.5 Please use VESA standard as below.y 784.8 mm (30.9 inch) and under * Wall Mount Pad Thickness : 2.6 mm * Screw : Φ 4.0 mm x Pitch 0.7 mm x Length 10 mmy 787.4 mm (31.0 inch) and above * Please use VESA standard wall mount pad and screws.10 cmModel19MB35P 23MB35PVESA (A x B)75 x 75100 x 100Standard screw M4Number of screws 422MB35P11USING THE MONITOR SETUSING THE MONITOR SETConnecting to a PCy Your Monitor set supports Plug & Play*. *Plug & Play: A PC recognizes a connected device that users connect to a PC and turn on, without device configuration or user intervention.D-SUB connectionTransmits analog video from your PC to theMonitor set. Connect the PC and the Monitor set with the supplied D-sub 15 pin signal cable asDVI-D connectionTransmits a digital video signal from your PC to the Monitor set. Connect the PC and the Monitor set with a DVI cable as shown in the followingillustrations.12USING THE MONITOR SETSelf Image Setting FunctionPress the power button on the bottom panel to turn the power on. When monitor power is turned on, the "Self Image Setting" Function is executed automatically. (Only supported in Analog Mode)13CUSTOMIZING SETTINGS CUSTOMIZING SETTINGS1Press the desired button on the bottom of the Monitor set.2Change the value of the menu item by pressing the buttons on the bottom of the Monitor set.To return to the upper menu or set other menu items, use the up arrow () button.3Select EXIT to leave the OSD menu.14CUSTOMIZING SETTINGSYou can set a response time for displayed pictures based on the y Analog: D-SUB(Analog signal) input.y Digital: DVI-D(Digital signal) input.15CUSTOMIZING SETTINGSPicture1 Press MENUto display the 2 Select the "3 Enter to 4 buttons.5 Select EXIT use the up arrow () button.16CUSTOMIZING SETTINGSSet your own gamma value. : Gamma 0, Gamma 1, Gamma 2 on themonitor, high gamma values display whitish images and low gamma values17CUSTOMIZING SETTINGSDisplay6 Select EXIT to leave the OSD menu.18CUSTOMIZING SETTINGSMENU 6 Select EXIT to leave the OSD menu.To return to the upper menu or set other menu items,use the up arrow () button.Each option is explained below.READER Setting1 Press READER button on the bottom of the Monitorset to display the Reader Mode OSD.2 Set the options by pressssing the ◄ buttons.Each option is explained below.EXIT21TROUBLESHOOTING TROUBLESHOOTING22TROUBLESHOOTING23SPECIFICATIONS SPECIFICATIONS19MB35PDisplay Screen Type48.2 cm (19 inch) Flat Panel Active matrix-TFT LCDAnti-Glare coatingVisible diagonal size: 48.2 cmPixel Pitch0.294 mm x 0.294 mm (Pixel Pitch)Sync Input Horizontal Frequency30 kHz to 83 kHz (Automatic)Vertical Frequency56Hz to 75Hz (D-SUB,DVI-D)Input Form Separate Sync. DigitalVideo Input Signal Input15 pin D-SUB Connector /DVI-D Connector (Digital)Input Form RGB Analog (0.7 Vp-p/ 75 ohm), DigitalResolution Max D-SUB(Analog) : 1280 x 1024 @ 60 HzDVI (Digital) : 1280 x 1024 @ 60 HzRecommend VESA 1280 x 1024 @ 60 HzPlug & Play DDC 2B(Analog,Digital)Power Consumption On Mode : 13 W (ENERGY STAR® standard)* Sleep Mode ≤ 0.3 WOff Mode ≤ 0.3 WPower Input AC 100-240V ~ 50/60Hz 0.8 ADimensions (Width x Height x Depth)With Stand40.9 cm x 48.1 cm x 21.0 cm Without Stand40.9 cm x 33.8 cm x 5.8 cmWeight 3.8 kg Tilt Range-5° to 20°Environmental conditions Operating TemperatureOperating Humidity10°C to 35 °C10 % to 80 %Storage TemperatureStorage Humidity-20°C to 60 °C5 % to 90 % non-CondensingStand Base Attached ( ), Detached (O)Power cord Wall-outlet typeProduct specifications shown above may be changed without prior notice due to upgrade of product functions.* The power consumption level can be different by operating condition and monitor setting.* The On mode power consumption is measured with ENERGY STAR® test standard.* ENERGY STAR® is a US registered mark of the United States Environmental Protection Agency.24SPECIFICATIONSSPECIFICATIONSDisplay Screen Type54.6 cm (21.5 inch) Flat Panel Active matrix-TFT LCDAnti-Glare coatingVisible diagonal size: 54.6 cmPixel Pitch0.248 mm x 0.248 mm (Pixel Pitch)Sync Input Horizontal Frequency30 kHz to 83 kHz (Automatic)Vertical Frequency56Hz to 75Hz (D-SUB,DVI-D)Input Form Separate Sync. DigitalVideo Input Signal Input15 pin D-SUB Connector /DVI-D Connector (Digital)Input Form RGB Analog (0.7 Vp-p/ 75 ohm), DigitalResolution Max D-SUB(Analog) : 1920 x 1080 @ 60 HzDVI (Digital) : 1920 x 1080 @ 60 HzRecommend VESA 1920 x 1080 @ 60 HzPlug & Play DDC 2B(Analog,Digital)Power Consumption On Mode : 19 W (ENERGY STAR® standard)* Sleep Mode ≤ 0.3 WOff Mode ≤ 0.3 WPower Input AC 100-240V ~ 50/60Hz 1.0 ADimensions (Width x Height x Depth)With Stand50.9 cm x 35.3 cm x 22.4 cm Without Stand50.9 cm x 30.4 cm x 14.4 cmWeight 3.9 kg Tilt Range-5° to 20°Environmental conditions Operating TemperatureOperating Humidity10°C to 35 °C10 % to 80 %Storage TemperatureStorage Humidity-20°C to 60 °C5 % to 90 % non-CondensingStand Base Attached ( ), Detached (O)Power cord Wall-outlet typeProduct specifications shown above may be changed without prior notice due to upgrade of product functions.* The power consumption level can be different by operating condition and monitor setting.* The On mode power consumption is measured with ENERGY STAR® test standard.* ENERGY STAR® is a US registered mark of the United States Environmental Protection Agency. 22MB35P25SPECIFICATIONS SPECIFICATIONS23MB35PDisplay Screen Type58.4 cm (23 inch) Flat Panel Active matrix-TFT LCDAnti-Glare coatingVisible diagonal size: 58.4 cmPixel Pitch0.2652 mm x 0.2652 mm (Pixel Pitch)Sync Input Horizontal Frequency30 kHz to 83 kHz (Automatic)Vertical Frequency56Hz to 75Hz (D-SUB,DVI-D)Input Form Separate Sync. DigitalVideo Input Signal Input15 pin D-SUB Connector /DVI-D Connector (Digital)Input Form RGB Analog (0.7 Vp-p/ 75 ohm), DigitalResolution Max D-SUB(Analog) : 1920 x 1080 @ 60 HzDVI (Digital) : 1920 x 1080 @ 60 HzRecommend VESA 1920 x 1080 @ 60 HzPlug & Play DDC 2B(Analog,Digital)Power Consumption On Mode : 21 W (ENERGY STAR® standard)* Sleep Mode ≤ 0.3 WOff Mode ≤ 0.3 WPower Input AC 100-240V ~ 50/60Hz 1.0 ADimensions (Width x Height x Depth)With Stand54.8 cm x 36.7 cm x 24.6 cm Without Stand54.8 cm x 33.5 cm x 16.6 cmWeight 4.5 kg Tilt Range-5° to 20°Environmental conditions Operating TemperatureOperating Humidity10°C to 35 °C10 % to 80 %Storage TemperatureStorage Humidity-20°C to 60 °C5 % to 90 % non-CondensingStand Base Attached ( ), Detached (O)Power cord Wall-outlet typeProduct specifications shown above may be changed without prior notice due to upgrade of product functions.* The power consumption level can be different by operating condition and monitor setting.* The On mode power consumption is measured with ENERGY STAR® test standard.* ENERGY STAR® is a US registered mark of the United States Environmental Protection Agency.26SPECIFICATIONSPreset Modes (Resolution) 19MB35P22MB35P 23MB35PIndicator27PROPER POSTUREProper posture for using the Monitor set.PROPER POSTUREangle.Make sure to read the Safety Precautions before using the product.Keep the Owner’s Manual (CD) in an accessible place for future reference.The model and serial number of the SET is located on the back and one side of the SET . Record it below should you ever need service.As an ENERGY STAR Partner LGE U. S. A.,Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.ENERGY STAR is a set of power-saving guidelines issued by the U.S.Environmental Protection Agency(EPA).MODELSERIAL*above information is only for USA FCC Regulatory Declaration of Conformity Trade Name: LGModel : 19MB35PE,22MB35PE, 23MB35PEResponsible Party: LG Electronics Inc.Address : 1000 Sylvan Ave. Englewood Cliffs NJ 07632 U.S.A TEL: 201-266-2534。
监视器 LCD 手册说明书
Monitor LCD Manual1. Precauciones (2)2. Desmontaje (4)3. Vista despiezada (13)4. Piezas adicionales (15)5. Mantenimiento (16)6. Autodiagnóstico (17)7. Solución de problemas (18)Monitor LCD1. Precauciones1-1. Precauciones de seguridadPRECAUCIÓNPRECAUCIÓN: PARA REDUCIR EL RIESGO DE DESCARGA ELÉCTRICA, NO RETIRE LA CUBIERTA (NI LA PARTE POSTERIOR). NO HAY PIEZAS QUE SE PUEDAN REPARAR EN EL INTERIOR. PARA CUALQUIER REPARACIÓN, ACUDA A PERSONAL CUALIFICADO.Monitor LCD 1-1-1. Electricidad y seguridad2. Desmontaje※ Los procedimientos para volver a montar siguen el orden inverso a los procedimientos para desmontar.※ Las piezas exteriores e interiores pueden variar según el producto.Delfín (BH81-00001A)Plantilla P 2017 para variosmontajes(BN81-14946A)Plantilla P 2017 para variosmontajes(BN81-14946B)Monitor LCDMonitor LCDRetire los 2 tornillos y levante el soporte en la dirección de la flecha.Monitor LCDMueva la plantilla de apertura siguiendo la dirección de la flecha paracrear una separación entre la Cubierta trasera y el panel.Compruebe el gancho SIN TORNILLO Superior/Izquierdo/Derecho de la CUBIERTA TRASERA y levántelo como se muestra en la figura.Monitor LCDMonitor LCDDesmonte el tornillo del punto 1 como se muestra en la imagen.Desmonte el enlace de soporte en la dirección de la flecha, como semuestra.Monitor LCDMonitor LCDRetire el Cable del conector de la placa principal.Sujete con la mano la pieza marcada y empújela en la dirección de la flecha para desconectar el cable.Empuje con la mano hasta el fondo la fuente de alimentación conmutada (SMPS) y se separará.Punto de descarga3. Vista despiezada3-1. Estructura•S60A / S60UA / S65UA / S80A / S80UA / S80PB•S70A124587634. Piezas adicionales5. Mantenimiento5-1. LimpiezaLos modelos muy brillantes pueden desarrollar manchas blancas sobre la superficie si se utiliza un humidificador de ondas ultrasónicas cerca.–Póngase en contacto con el Centro de servicio al cliente de Samsung más cercano si desea limpiar el interior del producto (se le cobrará una tarifa por este servicio).No ejerza presión con las manos u otros objetos sobre el producto. Existe riesgo de dañar la pantalla.–Tenga cuidado al limpiar el producto, ya que el panel y la parte exterior de las pantallas LCD avanzadas se arañan con facilidad.Ponga en práctica los pasos siguientes durante la limpieza.1. Apague el producto y el PC.2. Desconecte el cable de alimentación del producto.–Sujete el cable de alimentación por el enchufe y no toque el cable con las manos húmedas. De lo contrario, podría producirse una descarga eléctrica.3. Limpie el producto con un paño limpio, suave y seco. Humedezca con agua un paño suave, escúrralo bien yluego úselo para limpiar el exterior del producto.–No utilice limpiadores que contengan alcohol, disolventes ni agentes tensioactivos en el producto.–No rocíe agua ni detergente directamente sobre el producto.4. Conecte el cable de alimentación al producto cuando termine de limpiarlo.5. Encienda el producto y el PC.6. AutodiagnósticoPantalla de PRUEBA7. Solución de problemas■Diagnóstico del producto (problemas de pantalla)Si se produce un problema con la pantalla del producto, ejecute el Autodiagnóstico para comprobar si el producto funciona correctamente.■Comprobación de la resolución y la frecuenciaSi se selecciona una resolución que no es compatible, puede que aparezca el mensaje Modo no óptimo durante un corto período de tiempo o que la pantalla no se muestre correctamente.–La resolución mostrada puede variar, según la configuración del sistema del PC y los cables empleados.■Compruebe lo siguiente.Precaución•Cuando se escuchan chasquidos (restallidos) en el producto.–Ese sonido podría ser consecuencia de una contracción o expansión derivada del cambio de la temperatura de los componentes externos o el circuito interno del producto.–NO se trata de un error del producto y no afecta a la vida útil del producto.Problema de instalación•Aparecen espacios en blanco a los cuatro lados de la pantalla cuando se conecta un cable HDMI o HDMI-DVI al producto y al PC.–Los espacios en blanco de la pantalla no tienen nada que ver con el producto.–Los espacios en blanco de la pantalla los crea el PC o la tarjeta gráfica. Para solucionar este problema, ajuste el tamaño de la pantalla en la configuración HDMI o DVI de la tarjeta gráfica.–Si el menú de configuración de la tarjeta gráfica no tiene una opción para ajustar el tamaño de la pantalla, actualice el controlador de la tarjeta gráfica con la última versión. (Póngase en contacto con el fabricante de la tarjeta gráfica o del PC para obtener más información sobre cómo ajustar la configuración de la pantalla.)Problema de la pantalla•El LED de encendido está apagado. La pantalla no se encenderá.–Compruebe que el cable de alimentación esté bien conectado.–Si se produce un problema con la pantalla del producto, ejecute el Autodiagnóstico para comprobar si el producto funciona correctamente.•El mensaje "Compruebe la conexión del cable y la configuración del dispositivo de la fuente." aparecerá.–Compruebe que el cable esté bien conectado al producto.–Compruebe que el dispositivo conectado al producto esté encendido.–Compruebe el estado de Modo PC/AV. ( → Sistema → Modo PC/AV → DisplayPort, HDMI, USB Type-C → PC o AV.)–Establezca la versión de DisplayPort conectada. ( → Sistema → Ver. DisplayPort → 1.1 o 1.2↑)•Modo no óptimo se muestra en la pantalla.–Este mensaje aparece cuando la señal de la tarjeta gráfica supera la resolución o la frecuencia máximas del producto.–Cambie la resolución y la frecuencia máximas a fin de adaptarlas al rendimiento del producto mediante la consulta de la tabla de modos de señal estándar.–Si aparece este mensaje y el dispositivo conectado no admite la función FreeSync, desactive FreeSync en el producto.•Las imágenes de la pantalla aparecen distorsionadas.–Compruebe la conexión del cable al producto.•La pantalla no presenta un aspecto claro. La pantalla está borrosa.–Retire cualquier accesorio (cable de extensión de vídeo, etc.) y pruébelo de nuevo.–Establezca la resolución y la frecuencia en los niveles recomendados.–Compruebe que la resolución y la frecuencia del PC estén establecidas en un intervalo de resolución y frecuencia compatible con el producto. A continuación, si es necesario, cambie la configuración según la tabla de modos de señal estándar de este manual y el menú Información del producto.•La pantalla es demasiado brillante. La pantalla es demasiado oscura.–Ajuste el Brillo y el Contraste.•El color de la pantalla no es uniforme.–Cambie la configuración de Color.•Los colores de la pantalla muestran una sombra y están distorsionados.–Cambie la configuración de Color.•El color blanco no parece realmente blanco.–Cambie la configuración de Color.•No hay imagen en la pantalla y el LED de encendido parpadea cada0,5-1 segundo.–Compruebe que el cable esté bien conectado al producto y al PC, así como que los conectores estén firmemente enchufados.–Pulse cualquier tecla del teclado o mueva el ratón para volver a la ventana anterior.–El producto está en el modo de ahorro de energía.•El texto está borroso.–Si está usando un sistema operativo Windows (p. ej. Windows 7, Windows 8, Windows 8.1 o Windows 10): Vaya a Panel de control → Fuentes → Ajustar texto ClearType y cambie Activar ClearType.•La reproducción de vídeo sufre intermitencias.–La reproducción de archivos de vídeo de gran tamaño y de alta definición puede sufrir intermitencias.Puede deberse a que el reproductor de vídeo no esté optimizado para el PC.–Intente reproducir el archivo en otro reproductor de vídeo.Monitor LCD Problema con el sonido•No hay sonido.–Vuelva a comprobar el estado de los auriculares conectados y ajuste el volumen.–Compruebe el volumen.–Verifique si el volumen del producto o el dispositivo de origen está silenciado.•El volumen es demasiado bajo.–Ajustar el volumen.–Si el volumen sigue siendo bajo después de subirlo al máximo nivel, ajústelo en la tarjeta de sonido del PC o el programa de software.•El vídeo está disponible pero no hay sonido.–No es posible escuchar sonido cuando se usa un cable HDMI-DVI o un cable DVI para conectar el dispositivo de entrada.–Conecte el dispositivo con un cable HDMI o un cable DP.Problema con el dispositivo fuente•Se oye un pitido cuando el PC se inicia.–Si se oye un pitido cuando se inicia el PC, debe llevar el PC a un servicio técnico.21。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
LCD Monitor结构设计指南一、LCD Monitor 组成图1-1结构部分通常主要分成五大部件：面框后壳主固定板底座与支架，转轴按键有时还会有装饰件。
以及包装设计，ID label设计。
二、整体设计准备首先要根据市场部（或企业划部）提供的产品企划书，完全了解客户的整体要求。
✧确定pane 规格、外型尺寸、锁附位置。
✧power、A/D板尺寸、高位器件尺寸、安全距离、接口位置，锁附孔位置。
✧确定按键板的位置、大小，行程。
✧确定LED灯的位置。
✧检讨外形尺寸：✧整体设计和装配：前框与后壳：通常LCD Monitor 的结构设计前后壳采用卡扣(snap)的连接，底部有时辅助2-4颗螺钉（一般分布在，左下角1颗，右下角1颗，靠近转轴部分1-2颗）增强连接，同时也方便拆卸。
Panel装配：通过后壳或铁盘固定，（前框增加guide ribs定位panel上、下、左、右四个方向，以避免panel与前框的开口有偏差、避免露panel边铁以及倾斜的发生）。
铁盘装配：通过螺钉固定在转轴上，同时在后壳上给铁盘增加定位销或增加上、下、左、右四个方向的guide ribs。
支架与底座装配：通常建议采用卡扣连接（减少包装尺寸，对用户而言可以免工具拆装）。
如果有可能支架也能与底座一起拆装，方便继续减小包装尺寸。
转轴：转轴通常与底座通过螺钉连接，整体装配后锁附到后壳上。
Lips(电源板)与A/D板：固定在铁盘上,铁盘开孔散热。
按键：采用悬臂式结构设计使塑料排键有弹性。
通过螺钉或卡扣固定在前框或者后壳上。
三、3D建模结构设计之前需要将ID 部门（或外部设计公司的）所作的2D 效果图(2D sketch)立体化，实体化。
（这一步有可能在设计公司已经做好了）。
这个过程我们称之为PID 建模过程，建成的3D Pro/E 数据称为master。
这个3D 数据包含了所有ID 想要的曲线和曲面，分型线和美工线，甚至外表面的拔模角度，以及所有外观部件的拆分。
PID 建模有很多种方法，这里介绍常用的一种骨架建模法：STEP1：建一个.prt文件，命名为Projectname-master.prt，（一般以项目命名，比如N1982w-master.prt）在该文件中先建几个主要的基准（Datum/Axis），比如说分型基准面，模块安装基准，PCB 装配基准面，铁盘背面基准，端子出口位置基准等；然后把不同外观部件的共有特征以点(Point)、线(Curve)、面(Surface)的方式表达出来。
线可以由草绘，点构成线，投影等方式来做。
建面的方式可以是扫描，混成，边界曲线构成和变倒角等方式来完成；将面合并(Merge)，在这里只可进行与共有特征有关的合并命令，不需体现只与单个零件有关的个别特征；STEP2: 建一个总装配文件（Assembly 文件），命名为Projectname.asm。
在总装配文件中首先采用默认装配(Default)装配上Projectname_master.prt 文件；其次建上所需要的各个部件,建议都按标准方式命名各个part，方便文件识别和制作材料说明文件时的效率，分别是前框Front-cover.prt，后壳Rear-cover.prt，底座Base.prt，支架stand.prt，按键button.prt, lens.prt (比如：图3-2),都以默认的方式装配进总装配文件；STEP3:在总装配图中分别激活单个部件，把Projectname_master.prt 文件中所有信息内容以Merge的图3-2方式拷贝到各个文件中（方法1：主菜单中找：Insert/Merge 命令）。
方法2：不用激活单个部件，直接在Menu Manager/Component/Adv utils/Merge 先选择部件名，然后选择Projectname_master.prt）；STEP4:打开单个部件的. Prt 文件，首先建立一个master 的层，把所有的点、线、面都放到该层中，目的是使界面简单化；选取该.prt 所需要的面进行Merge，不需要的线和面可以在层里隐藏起来，最终得到自己想要的一个封闭的面，长成实体(Protrusion)。
STEP5:其它.prt 文件同STEP4一样操作，最后得到一个符合ID 外观要求的没有内部结构特征的3D模型装配图。
在3D 建模过程中要注意以下几点：1)在Projectname_master.prt 文件中做好以下工作：整机的外观尺寸、分模线和分模基准面、拔模角度Draft angle、光滑过渡的园角（指与外观有关的大的圆角）;2)所有Part 能公用的Curve 也全放在这个骨架模型中：如按键、喇叭，支架，各种端子出口等；3)在Projectname_master.prt文件中，建议在面和面结合的地方尽量不要倒圆角，因为圆角在Pro/E 的重生过程中，很容易造成错误；有时在后面的结构设计中也会对抽壳(Shell)造成困扰。
4)对于点、线、面：尽量用简单的Curve线：顺序如直线>简单圆弧>复杂圆弧>多义线>复杂的点或面；最好不要直接在总装配中生成(Creat)单个Part，单个Part 应该单独生成：这样可以拥有独自的Right、Front、Top 基准面，而不是Datum1、Datum2 等基准的名称。
这样我们在建模和后续的结构设计的过程中，尽量采用这些原始的基准面作为参照；拔模的方式尽量用扫描Sweep 成面的方式，这样便于以后修改；如果ID的外形有变化时，可以直接在Projectname_master.prt 文件中修改，然后重新生成（Regenerate）其它.prt 就行了。
5)当一个部件.prt 在一个文件夹中需要移到其它文件夹中时，一定要采用Back up 的方式，否则Projectname_master.prt 文件不会随之移动，这样.prt 文件就不能重生；6)在建模初期，一般不可能把所有关系到其它零件的共有特征都在Projectname_master.prt 文件中表达出来，其实是没关系的，照样可以继续进行。
因为在建模的过程中是可以继续在master文件中添加特征的，各零部件只要重新生成一下就行了。
7)Merge 命令与Copy命令的区别：对于将Projectname_master.prt中的信息拷贝到各个子零部件中的方式、Merge 命令优于Copy 命令。
因为Merge 命令只要不进行不同文件夹之间的移动，单个子零件通常是不会与Projectname_master.prt 失去联系的，只要重新生成，Projectname_master.prt文件中所有的特征都能融到单个的子零件中；但对于Copy命令，当在重新装配的过程中，经常会出现子零件与Projectname_master.prt 失去相关关系，子零件会与Projectname_master.prt相互独立。
也就是说在改动Projectname_master.prt零件时，单个的子零件不会随之改动。
而对于Merge 命令，在不同文件夹中移动.prt 时，就可以用上面提到的Back up的方式来避免。
但是Merge命令中只要改动一点Projectname_master.prt 文件，所有的零件都会改动，很可能会产生大的影响，反之Copy命令通常只与Copy 的特征有关。
3D 建模完成后，下一步就可以进入内部结构设计。
以下分别介绍各个part的设计要点：（注：对于各个part相同或相通的特征（比如rib,boss,snap，wallthickness特征等）一般在前面有提到，后面part将不再重复）四、前框、后壳设计一.设计流程：前框对应的部位：S4S2S9S10S11S12二. 可视框(opening)设计：开口设计遵循的原则是：允许塑料在公差许可的范围内（公差标准参考《tolerance_ABS 》，保证Active area 区域全部可见，同时不露出panel 的铁边（bezel ）: ◆ 通常开口X 向尺寸=(Bezel opening +Active area)/2 (X 方向) ◆ 通常开口Y 向尺寸=(Bezel opening +Active area)/2 （Y 方向◆ 开口处rib Z 向(厚度)尺寸确定（距离玻璃基板距离0.2mm,距离Bezel 距离0.0mm ）。
◆ 开口处rib X 向（水平）尺寸确定（距离bezel openling 0.3mm,距离Bezel 加强筋0.2mm.）。
◆ 开口处rib Y 向（垂直）尺寸确定（距离bezel openling 0.3mm,距离Bezel 加强筋0.2mm.）。
◆ 开口处rib 倒R 角0.5mm◆ Panel 不建议与前框大面接触。
通常在前框做一条环绕的rib :1mm ×0.5mm(高)支撑panel 。
距离开口处6mm 左右。
也可以把这条rib 分解成多条短线。
◆ 开口出四角倒圆R1◆ 设计尺寸参考如（图2-1），对于不同的寸别panel ，bezel opening 与Active Area 的大小是不一样的。
即使是同一寸别的panel ，各个厂家也做的不一样大小，甚至同一个厂家的同一寸别的panel 的bezel opening 与Active Area 不一样，对于这一点，设计师尤其要注意，认真的审阅规格书是每次设计必须要做的，尤其是同一个前框兼容不同厂家的panel 的时候，设计师更需要在proe图4-2-1里做好3D模型，在模型里注明panel的型号，厂家，画出bezel opening与Active Area大小。
三.胶厚设计与拔模角（wall thickness）：4.1塑胶材料：3.1.1胶厚(wall thickness)对于已经确定好外形尺寸的PID模型，下一步就是抽壳，确定材料的厚度和拔模角度。
设计遵循基本原则是保证产品的强度需求，最理想的壁厚分布切面在任何一个地方都是均一的厚度。
如实在无法避免，建议从厚向薄方向过度要平滑，另外两壁相连转角要圆滑。
（(详细见《产品结构设计的基本准则》胶厚设计)。
）LCD Monitor塑料件通常采用ABS(常用有奇美PA757,三星SD150)，建议设计胶厚为2.2-2.8mm之间，通常高光面取2.5mm，咬花面取2.2mm。
主要考虑是前框是外观A面，前框胶薄容易缩水。
高光材料通常用PMMA+ABS (常用LG XG569C),该材料的表面硬度可达1H ，普通ABS 硬度2B ～1B 左右）。
常用三种材料设计壁厚设计参考如图通常硬度越高，材料越脆。
螺钉硬度要选硬度高的。
如果选用ABS 直接做高光材料的话，建议选择PA757，可以节约成本,通常PMMA+ABS 相比纯ABS 价格高2.5～3倍左右，(LG XG569C 33元/公斤，PA757 13元/公斤)。