落地洗手盆使用说明书
落地式台盆柜施工说明书
落地式台盆柜配件明细表1止水栓2个名称数量※顾客自配部件2018.09■严格遵守的内容种类如下图所示进行区分说明。
·安装之前请在认真仔细阅读【安全上的注意】的基础上，正确安装。
·在此说明书上，为了能够正确安全的安装本产品，告知了必须要遵守的注意事项。
·同包装的使用说明书是给顾客的重要资料，请保留备用，切勿遗失或损坏，安装完成后，请交给顾客。
安装产品前请仔细阅读本施工说明书，并保留备用。
执行标准：GB 24977-2010 东陶机器（广州）有限公司 厂址：广州市番禺区南村镇兴南大道715号LDEW605HRK/W LDEW755HRK/W系列系列产品型号系列系列系列系列A B C D E F GLDEW605HRKLDEW605HRWLDEW755HRKLDEW755HRW60075012080550400287.5500130570362.5①1.墙体作业参照施工尺寸图，在墙壁上钻孔，并将配件内的膨胀管埋入墙壁内。
2.安装止水栓将柜体放置到安装位置，确认墙固定孔、墙给水孔、地排水孔位置均已对齐。
注意：安装止水栓前，请先将墙给水管内的垃圾清理干净。
3.安装墙壁固定螺丝注意：必须安装墙壁固定螺丝。
取配件内排水弯管，按下图所示，完成安装。
安装步骤：污管进入房间内。
强制※由于地面不平整，产品晃动情况下， 可通过底脚调节装置进行调整。
6.水嘴的安装※水栓的安装方法请参照其自附的说明书进行正确的施工。
5.接水箱的使用※接水箱的安装请参照使用说明书进行正确使用。
2、检查并确认门机能完好。
（如需调整，使用说明书P.9参照）3、清理、清扫施工所产生的废弃物。
4、向洗脸盆内注水，确认排水弯管、各部连接处没有漏水发生。
1、水嘴、电器类的安装请参照其自附的说明书进行正确施工。
2、使用前请仔细阅读产品使用说明书，正确使用本产品。
3、为了保持产品的美观，请从平时起做好保养工作。
■ 其它·如果您需要废弃本产品，请勿将其作为一般生活垃圾处理，请依照法 规经由独立的回收体系进行合适的处理、恢复和回收。
WT500A 洗手台说明书
Montage- und Betriebsanleitung Mounting instruction and Manual EA-Nr.: 7612210001017 - WT500A ( 500x200x402 mm ) Waschtisch, CNS, ÜberlaufWashstand, CNS, overflowALG Sarl BFIX Groupe Résidence Chaabani, Val d‘Hydra 16000 Alger / Algeria t: +213-(0)21 60 13 60e:***********************AUT Franke Ges.m.b.H Oberer Achdamm 526971 Hard / Austria t: +43-(0)5574-6735-0e:*********************BEL Franke N.V.Ring 10, PB 1179400 Ninove / Belgium t: +32-(0)54-310130e:*********************CAN Franke Kindred Canada Limited 1000 Franke Kindred Road L4R 4K9 Midland, Ontario / Canada t: +1-705-526-5427e:*********************CZE Franke s.r.o.Kolbenova 1719000 Praha 9 / Czech Republic t: +420-281-090-429e:*********************EGY Franke Kitchen Systems Egypt S.A.E. 1st Industrial Zone 6th October City, Cairo / Egypt t: +20-(0)2-828-0000 e:*********************ESP Franke WS Iberia Avda. Puente Cultural, 10, 1º- 6San Sebastian de los Reyes, 28703 Madrid t: +34-(0)91-659-3197e:*********************FIN / SWE / NOR / DEN Franke Finland Oy Vartiokuja 176850 Naarajaervi / Finland t: +358-(0)15-3411-1e:*********************FRA Franke Ges.m.b.H Oberer Achdamm 526971 Hard / Austriche t: 0800 909 216e:*********************GBR / IRL Franke Sissons Ltd.Carrwood Road, Sheepbridge Chesterfield S41 9QB / United Kingdom t: +44-(0)1246-450-255e:*********************GER Franke Aquarotter GmbH Parkstrasse 1 - 514974 Ludwigsfelde / Germany t: +49-(0)3378-818-0e:*********************GEO Franke Caucasus Ltd.7, Agladze Street Tbilisi, 0154 / Georgia t: +995-(0)32-351672e:******************GRE G Style S.A.119, Kifissias Ave.GR-151 24 Maroussi, Athens / Greece t: +30 210 614 1196e:***************HUN Franke Ges.m.b.H Oberer Achdamm 526971 Hard / Austria t: +36-(0)1-313-84-84e:*********************ITA Franke Ges.m.b.H Oberer Achdamm 526971 Hard / Austria t: 800-789233e:*********************NED Franke N.V.Ring 10, PB 1179400 Ninove / Belgium t: +31-(0)88-0027-368e:*********************POL Franke Polska Sp. z o.o.Aleja Krakowska 6305-090 Raszyn, Sekocin Nowy / Poland t: +48-(0)22-711-6717e:*********************POR Franke Portugal S.A.Estrada de Talaíde, Edificio 3, Cruzamento de Sao Marcos, 2735-531 Cacém / Portugal t: +351-(0)21-426-9670e:********************* ROU Franke Romania SRL 98, Blvd. Biruintei 077145 Bucharest - Pantelimon / Romania t: +40-(0)21-350-1550 e:*********************RSA Franke Kitchen Systems (Pty) Ltd.1194 South Coast Road 4060 Mobeni / South Africa ZAF t: +27-(0)31-450-6300e:*********************RUS Franke Russia Ilya Klestov ul. Novorossiiskaya 32-44 195156 St. Petersburg / Russia t: +7-(0)921-315-35-36e:********************* SLO Barjans d.o.o.Pod Hruševco 201360 Vrhnika / Slovenia t: +386-(0)1-750-66-40e:***************SUI Franke Washroom Systems AG Franke-Strasse 9, Postfach 2374663 Aarburg / Switzerland t: +41-(0)62-787-3131e:*********************SVK INGEMA s.r.o.Močarianska 1071 01 Michalovce / Slovakia t: +421-(0)56-640-36-12e:****************TUN HANDASSA GROUP 48 Av. Taieb Mhiri Imm. Les Jasmins apt. n°5.2080 Ariana / Tunisia t : +216-(0)71-702-272e:**********************.tn TUR Franke Mutfak ve Banyo Sistemleri San. ve Tic. A.S Gebze Organize Sanayi Bölgesi Tembelova Alanı 3500 sokak No: 3503 Gebze, Kocaeli / Turkiye t: +90-(0)262-644-6595e:*********************UAE Franke L.L.C P .O. Box 14511Ras Al Khaimah / United Arab Emirates t: +971-(0)7-244-4940 e:*********************UKR Franke Ukraina LLC 7D, Zdolbunivska Str.Kyiv 02081 / Ukraine t: +380-(0)44-492-0015e:*********************Other Countries:Franke Ges.m.b.H Oberer Achdamm 526971 Hard / Austria t: +43-(0)5574-6735-0e:**********************1. Wichtige Hinweise / Important notes . . . . . . . . . . . . . . . . . . . . . . . . . . .2. Lieferumfang / Scope of supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3. Maße / Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5. Montage / Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Inhaltsverzeichnins / Table of contents 2. Lieferumfang / Scope of supply1. Wichtige Hinweise / Important notesWichtig!• Vor Montagebeginn muss die Montageanleitung gelesen und verstanden werden.• Montage nur durch Fachpersonal durchführen.• Die beigefügten Befestigungselemente nur für Ziegel- oder Betonmauerwerk verwenden.Important!• Before the start of installation, the installation instructions must have been read and understood.• Installation only by specialist personnel.• The enclosed mounting elements must be used only for brickwork orconcrete masonry.2233 3. Masse / Dimensions4. Montage / MountingStück Benennung1 Stopfenventil mit Überlauf 5/4“1 BefestigungssetPieces Designation1 Plug valve with overflow 5/4“1 Attachment set。
KOHLER 浴室洗手盆说明书
• READ THESE INSTRUCTIONS THOROUGHLY BEFORE YOU BEGIN.• Follow all local plumbing and building codes.• Before installation, please inspect the sink for damage. Do not insall a damaged sink.• For drop-in sinks proceed to section I. For undermount sinks proceed to section II.I. DROP-IN INSTALLATIONNote: The clips provided are designed for a maximum counter-top thickness of 1-3/4”.1. To dertermine the proper size opening for you sink place the sink upside down on top of the countertop. Mark or trace line around the edge of the rim. Then cut an opening 5/16” inside the line. (See illustration A).2. Set new sink in opening to see that it fits properly.3. Faucet Holes: Faucet holes can bei dentified by the faucet hole emboss on the underside of the faucet deck and the corresponding circular labels located on the faucet deck top surface. Before punching the holes please verify that the circular labels are properly centered over the faucet hole emboss. The faucet hole should be carefully penetrated from above the sink using a chisel or screw driver and tapping lightly on the circular labels. (See illustration B). If necessary the hole can been enlarged using a metal hole saw, a jigsaw with a metal cutting blade or a metal file.Note: MUST SUPPORT FAUCET DECK ON BOTH SIDES WHILE PUNCHING FAUCET HOLES.4. Attach faucet, drain fittings and accessories according to the manufacturer’sinstructions.5. As shown in illustration C and D, align clips with the corre- sponding slots in the sinks per illustration C. It may be necessary to use a mallet and wood block to push it into place, as shown in illustration D. Make sure metal portion of the clip (clamp) is in the open position so that sink can be dropped into cutout.6. Apply a bead of a high quality silicone adhesive caulk to the underside of the sink rim and position sink into countertop opening. CAUTION: Use only a high quality silicone adhesive caulk.7. Swing metal portion of clip (clamp) into the clip base. (See illustration E). Using a phillips screw driver, turn screw until clamp engages the countertop. Use shims if necessary.8. Remove excess caulk and allow caulk to cure following the caulk manufacturer’s instructions.Quartz SinkInstallation InstructionsILLUSTRATION AILLUSTRATION BTRACE COMPLETELY AROUND EDGE OF SINKDRAW SECOND LINE INSIDE SINK OUTLINE (CUT LINE)5/16"TO BE REMOVED FOR USE BY THE OCCUPANT!CLAMPILLUSTRATION C ILLUSTRATION D ILLUSTRATION EElkay2222Camden Court Oak Brook,IL 60523©2016Elkay Printed in (Rev. 08/16) 74180028ELKAY LIMITED LIFETIME QUARTZ SINK WARRANTYElkay warrants to the original purchaser of an Elkay Quartz sink that Elkay will,at its option, replace or repair, without charge, such product if it fails due to a man-ufacturing defect for a lifetime of normal residential use. Product replacement does not include transportation cost or labor installation cost.This warranty covers only quartz drop-in sinks installed in a conventional countertop surface and quartz undermount sinks installed in a conventional solid surface counter-top and applies to residential installations only. Elkay reserves the right to exam-ine product in question and its installation prior to replacement.WASTE FITTINGS AND ACCESSORIES ARE NOT WARRANTEDOTHER WARRANTY CONDITIONS ON SINKSThis warranty applies to sinks purchased after August 1st 2007as shown on the purchaser’s dated receipt.Our warranty does not cover product failure or damage caused by abusive treatment,misuse,environmental factors,normal wear includ-ing dents and scratches,improper care and cleaning,use of aggressive and abra-sive cleaners,damage due to handling or failure to follow the recommended pro-cedures for installation,care and maintenance as detailed in the installation and care guide provided with every sink.This warranty is extended only to the original consumer purchaser of the product.This warranty does not cover shipping costs,labor costs,or any other charges for such items as installation or replacement of the sink,diagnosis or replacement of any faucet or component part,or any other expense or loss.All incidental or consequential damages are specifically excluded.No addi-tional warranties,express or implied are given,including but not limited to,any implied warranty of merchantability or fitness for a particular purpose.Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts,so the above limitations or exclusions may not apply to you.This warranty gives you specific legal rights,and you may also have other rights which vary from state to state.TO OBTAIN SERVICE UNDER WARRANTY 1.In the USA,write to:In Canada,please contact /Elkay Manufacturing Company Au Canada,pour toute demande Attention:Consumer Services de garantie,veuillez contacter:2222Camden Court ELKAY Canada LtdOak Brook,IL 605237000Pine Valley Drive,Unit 102Vaughan,Ontario L4L 4Y82.Include a letter containing the following information:a.Date of purchase and installationb.Proof of Purchase (copy of original dated invoice)c.Description of nature of defectd.Model number or description of model and/or component part if possible.Installation InstructionsII. UNDERMOUNT INSTALLATION1.Position template on countertop.Locate front to rear,so sink will not interfere with the cabinet.2.T race a line around the template.Cut along the inside of this line to provide opening.3.Locate and provide for the mounting holes (following the countertop manufacturer’s instructions).Holes should allow for even spacing around sink.T ype of fasteners to be as recommended by countertop supplier.4.Fasten mounting brackets to countertop loosely.ing a high quality silicone adhesive caulk,apply a bead evenly all around the top of the sink flanges.6.Position and align the sink in the countertop opening.7.Tighten fasteners until mounting brackets are snug against sink. (See illustration F).8.Check alignment of sink to countertop opening.9.Tighten down fasteners evenly.Be careful not to over-tighten.Remove excess caulk and allow caulk to cure following the caulk manufacturer’s instructions.CARE AND CLEANING GUIDEElkay Quartz was created for a lifetime of easy care. Just follow the simple guidelines listed below.Routine CareMost dirt and stains: Use soapy water and a sponge, towel dry.Watermarks: Wipe with damp cloth and towel dry.Difficult stains: 50/50 water/bleach solution or non-abrasive cleaners. Follow cleaning manufacturer’s instructions, rinse thoroughly, towel dry.Preventing Damage• Avoid exposing Elkay Quartz to strong chemicals, such as paint removers, oven cleaners, etc. If contac toccurs, quickly flush the surface with water. Do not use a straight or undiluted bleach solution.• Do not set hot pans directly into sinks.• Run cold water when pouring boiling water into sinks.• Do not use any abrasive cleaning products, scouring pads or steel wool.• Do not use caustic solutions containing ammonia or alkalis.ATTENTION INSTALLER:•ELKAY RECOMMENDS THA T UNDERMOUNT SINKS SHOULD BE INSTALLED BY A PROFESSIONAL EXPERIENCED INSTALLER.•WARNING:THE ENCLOSED CUTOUT TEMPLA TE PROVIDES A SINK OPENING THA T WILL EXPOSE APPROXIMA TEL Y 1/8"OF SINK RIM LEDGE AS SHOWN IN ILLUSTRA TION E.•IT IS RECOMMENDED THA T YOU DISCUSS THIS WITH YOUR CUSTOMER AND AGREE TO WHA T THE FINISHED EFFECT WILL BE.ELKAY IS NOT RESPONSIBLE FOR IMPROPER SINK OR COUNTERTOP INSTALLA TIONS.•ELKAY QUARTZ UNDERMOUNT SINKS MUST BE FASTENED TO SOLID SURFACE COUNTERTOPS ONLY (I.E.GRANITE).•ELKAY IS NOT RESPONSIBLE FOR SINK AND COUNTERTOP IF DAMAGED DURING INSTALLA TION.•FOLLOW ALL LOCAL PLUMBING AND BUILDING CODES.ILLUSTRATION FCOUNTERTOPSINK。
三站厨房洗手沐浴盆 EWMA7220 产品说明书
ModelA B C D E F G H I J K Number in.mm in.mm in.mm in.mm in.mm in.mm in.mm in.mm in.mm in.mm in.mmEWMA7220 72 1829 20 508 69 1753 161/2 419 36 914 11/2 38 10 254 2 51 24 610 12 305 8 2037-3/4"(197mm)7/16" (11mm) x 3/4" (19mm)LONG SLOT ST AINLESSSTEEL BRACKETS6-3/8"(162mm)1-1/2" (38mm) O.D.33-1/2"(851mm)JI8-7/8"(225mm)3-1/4" (83mm) DIA. FOR LK18B DRAIN1/4" R (6mm)FFHACEDBEGK3-1/2"(89mm)9-1/8"(232mm)1/4" R (6mm)5-3/8"(137mm)36" (914mm)SUGGESTED FLOOR TO RIM HEIGHTHIJ33-1/2"(851mm)13-3/4"(349mm)7-3/4"(197mm)F4-1/4"(108mm)GKHH14"(356mm)1-1/4" (32mm) DIA.(3 HOLES)WHANGER7/16" (11mm)DIA. HOLEThree Station Wall Mounted Wash Sink With Sensor Faucets, AC Battery Powered Models EWMA7220SACC,EWMA7220SACMC and EWMA7220SACTMC ®SPECIFICATIONSGENERALEWMA7220#14 gauge, type 304 (18-8) stainless steel three station wash sink with 1/4" (6mm) radius coved corners. 1-1/2"(38mm) wide sloping top channel rims, with 2" (51mm) flat apron. Full length 10" (254mm) high backsplash. Rim corners are square. Exposed surfaces are hand blended to a uniform satin luster finish. Furnished with wall hangers and stainless steel support brackets.(CHECK MODEL SPECIFIED)MIXING MODEL FAUCET DRAIN VALVE EWMA7220SACC LKB722C (3) LK18B NONE EWMA7220SACMC LKB722C (3) LK18B LK724 (3)EWMA7220SACTMC LKB722C (3)LK18BLK723 (3)Elka y Manufacturing Compan y 2222 Camden Court Oak Brook, IL 60523Printed in U.S.A.©2010 Elkay Mfg. Co.(Rev. 4/10) 3-45AModel EWMA7220SACCDIMENSIONSLK18B Stainless steel perforated grid strainer with 1-1/2"(38mm) O.D. stainless steel tailpiece.LK723Anti-scald thermostatic mixing valve with nickel-plated brass body 1/2" (13mm) SWT inlets and outlet connections,check valves on inlets and a mixed temperature range of 80°- 120°F . Certified under ASSE1016.LK724Mechanical mixing valve with C.P . brass body, 3/8" (10mm) compression inlets and outlet connections, and check valves on inlets.LKB722C Sensor-operated, non-mixing backsplash -mounted gooseneck faucet with adjustable sensor eyes. A continuous beam is emitted from sensor. The sensor facuet is activated by user placing hands under the spout. Water will flow as long as hands remain within sen sor range. When hands are removed the water stops automat ically based on shut off delay settings.The sensor then resets and is ready for the next user.C hrome -plated solid brass body construction with 2.0gpm laminar f low control on spout end.Includes water-resistant sensor control module and power cables.Features dual power options: AC plug-in and battery holder with f our AA batteries. Slow-closing piston operated solenoid valve,in-line filter with clean-out trap and flexible supply hose.Control circuit is solid state, has adjustable sensor range of 7/8" (22mm) to 6-3/4" (171mm), shut-off delay preset to 1 second and field adjustable to 2 seconds (to prevent sink overflow).®Elkay Manufacturing Company2222 Camden Court Oak Brook, IL 60523Printed in U.S.A.©2010 Elkay Mfg. Co.3-45A (Rev. 4/10)Three Station Wall Mounted Wash SinkWith Sensor Faucets, AC / Battery Powered Models EWMA7220SACC,EWMA7220SACMC and EWMA7220SACTMCSINK。
AXENT 浴室家具用户手册说明书
Tel:800 820 9880 400 888 9880E-mail:************************Bathroom Furniture P /N :224000089900浴室家具USER MANUAL用户手册101感谢您的信任使用说明与清洁维护备注：本手册的解释权属于厦门优胜卫厨科技有限公司。
温馨提示欢迎使用AXENT 品牌产品安装前温馨提示衷心感谢您购买AXENT产品，在您使用产品之前，您可以从本手册中了解有关产品安装及使用方法等重要事项.请您遵循说明书中的记载事项。
请在阅读后，与保修卡、安装说明书一起妥善保管，以备日后需要时查阅。
本手册的插图仅为示意图，具体请以产品实物为准。
本手册含【安装说明】我们期待您能通过本手册掌握AXENT产品的安装及使用方法。
为确保该产品能提供最佳的功能及保证您的人身安全。
使用说明使用前，请务必将陶瓷盆按要求安装好，并接好去水；必要时，请使用少量的硅胶将陶瓷盆与浴室柜台面板密合；使用时，请不要用力或用重物敲打，扭搬浴室柜，以免损坏产品影响使用；使用时，请不要用尖锐的物品或金属制品敲浴室柜，以免损坏产品影响使用；使用时，请不要强力拖动浴室柜，以免损坏产品使用；需要移动浴室柜时，请务必将锁墙螺丝解开后才可进行，以免损坏产品影响使用。
凡残障和（或）认知能力有限的个人（包括儿童），或不具备必要的使用知识的人不得独自使用本产品。
这些人必须在有能力对其安全负责的成人的严格监护和指导下方可使用本产品。
请照看好儿童，确保其不操作此设备。
清洁维护使用稀释后的中性清洁剂清洁产品表面，请勿使用下列物品：苯，涂料稀释剂，去污粉，尼龙刷。
在蒸气的环境中使用后，请及时通风保持浴室干燥。
请详细阅读说明书，以便熟悉所需的工具、配件及安装步骤，避免由于安装不当造成不必要的损失。
本说明书所载之相关资料，乃以印刷产品之最新状况为依据，对于产品特性、包装及供应情形，本公司保留随时修改之权利，恕不另行通知。
Kohler Co. 厕所澡盆安装说明书
11114848-2-BA (A)E1998 Kohler Co.ACRYLIC BATHS2Kohler Co., Kohler, WI114848-2-BA(A)Kohler Co., Kohler, WI114848-2-BA(A)34Kohler Co., Kohler, WI114848-2-BA(A)Kohler Co., Kohler, WI114848-2-BA(A)56Kohler Co., Kohler, WI 114848-2-BA(A)Please take a moment to familiarize yourself with theKohler Warranty, its benefits, and limitations. Kohler Co.and its distributors support you with one of the largestService Networks of its type. Here’s what you need to doif you require service:1.Contact the dealer or contractor who sold andinstalled the product. They should be able to solveany problems you may have.2.If your dealer or contractor cannot solve theproblem, they will contact or supply you with thename of the local Kohler Distributor and the:3.If you are unable to obtain warranty service througheither your contractor or Kohler Co. distributor,please write us directly at Kohler Co., Attn:Customer Service Department, 444 HighlandDrive, Kohler, WI 53044 U.S.A.4.Include all pertinent information regarding yourclaim, including a complete description of theproduct, model numbers, colors, finishes, and thedate the product was installed. Include a descriptionof the problem, and a photocopy of your invoice forthe products involved. Also give us the name of thecontractor and distributor.Kohler Co., Kohler, WI114848-2-BA(A)78Kohler Co., Kohler, WI 114848-2-BA(A)。
Elkay Lustertone Classic 单盆ADA浴室洗手盆说明书
PRODUCT SPECIFICATIONSElkay Lustertone Classic Stainless Steel 25" x 21-1/4" x 6-1/2" Single Bowl Drop-in ADA Sink. Sink is manufactured from 18 gauge 304 Stainless Steel with a Lustrous Satin finish, Rear Center drain placement, and Bottom only pads.Part # 64090012 included for countertopsTemplate is available for download at . CAD software will be required to open the template. Cutout Dimensions for Drop-in Installation: 24-3/8" x 20-5/8" (619mm x 524mm) with 1-1/2" (38mm) corner radius Hole Drilling Configurations:A Century of Tradition and Quality. For more than 100 years, Elkay has beenmaking innovative products andproviding exceptional customer care. Wetake pride in offering plumbing products that make life easier, inspire change andleave the world a better place. Product Compliance: ADA & ICC A117.1 ASME A112.19.3/CSA B45.4 Sinks are listed by IAPMO ® as meeting the applicable requirementsof the Uniform Plumbing Code ®, International Plumbing Code ®, and National Plumbing Code of Canada.Complies with ADA & ICC A117.1 accessibility requirements when installed according to the requirements outlined in these standards.Clean and Care Manual (PDF)Installation Instructions (PDF) - 1000005236 Warranty (PDF)Similar models are available with: CuVerro antimicrobial copper, Quick-Clip Mounting System, additional ADA depthsPART:________________________________QTY: _____________ PROJECT:______________________________________________ CONTACT:______________________________________________DATE:__________________________________________________ NOTES:_________________________________________________ APPROVAL:_____________________________________________Installation Profile:Elkay Gourmet Single Hole Kitchen Faucet Pull-out Spray and Lever Handle with Hi and Mid-rise。
使用便盆的操作流程
使用便盆的操作流程准备工作在使用便盆之前，需要进行以下准备工作：1.确保便盆干净且无异味。
2.准备好足够的清洁纸巾或湿巾。
3.打开窗户或开启通风设备，保持室内空气流通。
步骤一：进入卫生间1.轻轻拉开卫生间门，确保门关上后能够从内部顺利打开。
2.确保卫生间里的空气流通，避免呼吸不畅。
3.如果有必要，可以在使用便盆前洗净双手。
步骤二：正确坐姿1.轻轻地移动到便盆旁边，保持平衡并正确坐下。
2.双脚平稳着地，双膝稍微向外展开，以放松肛门肌肉。
3.尽量保持身体放松，避免用力用腹部压迫。
步骤三：便后清洁1.使用清洁纸巾或湿巾轻轻擦拭肛门和周围区域，从前往后的方向进行。
2.擦拭时要注意力度，不要过度刺激皮肤。
3.如果有必要，可以使用一些温水清洁剂进行清洁。
步骤四：洗手1.在便盆旁边放置一些洗手液和清水。
2.洗净双手，搓揉并彻底清洗至少20秒，确保清洁。
3.用干净的纸巾或毛巾擦干双手。
步骤五：清理便盆1.使用适当的清洁剂，如漂白剂或清洁液，彻底清洁便盆内外表面。
2.用清水冲洗并擦干便盆，确保干净无异味。
3.将便盆内的废弃物倒入马桶，并冲洗干净。
步骤六：整理卫生间1.清除卫生间里的废纸，将其放入垃圾袋中。
2.清洁卫生间地板和墙壁，清除任何污渍或水迹。
3.确保卫生间内部干燥，并关闭窗户或通风设备。
小贴士•建议使用软质纸巾或湿巾，以减少对皮肤的刺激。
•手部清洁十分重要，应注意充分清洗。
•不要将任何异物或过多纸巾等废弃物放入便盆。
•定期清理便盆，保持卫生间的整洁。
以上是使用便盆的操作流程，希望对您有所帮助！记得保持卫生，谢谢！。