7448258022;中文规格书,Datasheet资料
744230181;中文规格书,Datasheet资料
2.1 2.0 1.02012-07-172012-07-172010-09-30SStSStSBaSStSBaWürth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyTel. +49 (0) 79 42 945 - 0A Dimensions: [mm]F Typical Impedance Characteristics:H1: Classification Reflow Profile for SMT components:H2: Classification Reflow ProfilesProfile FeaturePreheat- Temperature Min (T smin ) - Temperature Max (T smax ) - Time (t s ) from (T smin to T smax )Ramp-up rate (T L to T P )Liquidous temperature (T L )Time (t L ) maintained above T L Peak package body temperature (T p )Time within 5°C of actual peak temperature (t p )Ramp-down rate (T P to T L )Time 25°C to peak temperature Pb-Free Assembly 150°C 200°C60-180 seconds 3°C/ second max.217°C60-150 seconds See Table H320-30 seconds 6°C/ second max.8 minutes max.refer to IPC/JEDEC J-STD-020DH3: Package Classification Reflow TemperaturePB-Free Assembly PB-Free Assembly PB-Free Assembly Package Thickness< 1.6 mm 1.6 - 2.5 mm ≥ 2.5 mmVolume mm³<350260°C 260°C 250°CVolume mm³350 - 2000260°C 250°C 245°CVolume mm³>2000260°C 245°C 245°Crefer to IPC/JEDEC J-STD-020DH Soldering Specifications:I Cautions and Warnings:The following conditions apply to all goods within the product series of WE-CNSWof Würth Elektronik eiSos GmbH & Co. KG:General:All recommendations according to the general technical specifications of the data sheet have to be complied with.The disposal and operation of the product within ambient conditions which probably alloy or harm the wire isolation has to be avoided.If the product is potted in customer applications, the potting material might shrink during and after hardening. Accordingly to this the product is exposed to the pressure of the potting material with the effect that the core, wire and termination is possibly damaged by this pressure and so the electrical as well as the mechanical characteristics are endanger to be affected. After the potting material is cured, the core, wire and termination of the product have to be checked if any reduced electrical or mechanical functions or destructions have occurred.The responsibility for the applicability of customer specific products and use in a particular customer design is always within the authority of the customer. All technical specifications for standard products do also apply for customer specific products.Cleaning solvents which are used to clean the application might damage or change the characteristics of the component.Direct mechanical impact to the product shall be prevented as the ferrite material of the core could flake or in the worst case it could break. Product specific:Follow all instructions mentioned in the datasheet, especially:•The soldering profile has to be complied with according to the technical reflow soldering specification, otherwise no warranty will be su-stained.•All products are supposed to be used before the end of the period of 12 months based on the transfer of title, if not a 100% solderability can´t be warranted.•Violation of the technical product specifications such as exceeding the nominal rated current will result in the loss of warranty.1. General Customer ResponsibilitySome goods within the product range of Würth Elektronik eiSos GmbH & Co. KG contain statements regarding general suitability for certain application areas. These statements about suitability are based on our knowledge and experience of typical requirements concerning the are-as, serve as general guidance and cannot be estimated as binding statements about the suitability for a customer application. The responsibi-lity for the applicability and use in a particular customer design is always solely within the authority of the customer. Due to this fact it is up to the customer to evaluate, where appropriate to investigate and decide whether the device with the specific product characteristics described in the product specification is valid and suitable for the respective customer application or not.2. Customer Responsibility related to Specific, in particular Safety-Relevant ApplicationsIt has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the usual lifetime can-not be completely eliminated in the current state of the art, even if the products are operated within the range of the specifications.In certain customer applications requiring a very high level of safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health it must be ensured by most advanced technological aid of suitable design of the customer application that no injury or damage is caused to third parties in the event of malfunction or failure of an electronic component.3. Best Care and AttentionAny product-specific notes, warnings and cautions must be strictly observed.4. Customer Support for Product SpecificationsSome products within the product range may contain substances which are subject to restrictions in certain jurisdictions in order to serve spe-cific technical requirements. Necessary information is available on request. In this case the field sales engineer or the internal sales person in charge should be contacted who will be happy to support in this matter.5. Product R&DDue to constant product improvement product specifications may change from time to time. As a standard reporting procedure of the Product Change Notification (PCN) according to the JEDEC-Standard inform about minor and major changes. In case of further queries regarding the PCN, the field sales engineer or the internal sales person in charge should be contacted. The basic responsibility of the customer as per Secti-on 1 and 2 remains unaffected.6. Product Life CycleDue to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a stan-dard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage about inevitable product discontinuance. According to this we cannot guarantee that all products within our product range will always be available. Therefore it needs to be verified with the field sales engineer or the internal sales person in charge about the current product availability ex-pectancy before or when the product for application design-in disposal is considered.The approach named above does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.7. Property RightsAll the rights for contractual products produced by Würth Elektronik eiSos GmbH & Co. KG on the basis of ideas, development contracts as well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer will remain with Würth Elektronik eiSos GmbH & Co. KG.8. General Terms and ConditionsUnless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms and Conditions of Würth Elektronik eiSos Group”, last version available at .J Important Notes:The following conditions apply to all goods within the product range of Würth Elektronik eiSos GmbH & Co. KG:分销商库存信息: WURTH-ELECTRONICS 744230181。
744225S;中文规格书,Datasheet资料
8.1 8.0 7.02012-07-172012-07-172004-10-11SStSStMSTSStSBaWürth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyTel. +49 (0) 79 42 945 - 0A Dimensions: [mm]F Typical Impedance Characteristics:H1: Classification Reflow Profile for SMT components:H2: Classification Reflow ProfilesProfile FeaturePreheat- Temperature Min (T smin ) - Temperature Max (T smax ) - Time (t s ) from (T smin to T smax )Ramp-up rate (T L to T P )Liquidous temperature (T L )Time (t L ) maintained above T L Peak package body temperature (T p )Time within 5°C of actual peak temperature (t p )Ramp-down rate (T P to T L )Time 25°C to peak temperature Pb-Free Assembly 150°C 200°C60-180 seconds 3°C/ second max.217°C60-150 seconds See Table H320-30 seconds 6°C/ second max.8 minutes max.refer to IPC/JEDEC J-STD-020DH3: Package Classification Reflow TemperaturePB-Free Assembly PB-Free Assembly PB-Free Assembly Package Thickness< 1.6 mm 1.6 - 2.5 mm ≥ 2.5 mmVolume mm³<350260°C 260°C 250°CVolume mm³350 - 2000260°C 250°C 245°CVolume mm³>2000260°C 245°C 245°Crefer to IPC/JEDEC J-STD-020DH Soldering Specifications:I Cautions and Warnings:The following conditions apply to all goods within the product series of WE-SL2of Würth Elektronik eiSos GmbH & Co. KG:General:All recommendations according to the general technical specifications of the data sheet have to be complied with.The disposal and operation of the product within ambient conditions which probably alloy or harm the wire isolation has to be avoided.If the product is potted in customer applications, the potting material might shrink during and after hardening. Accordingly to this the product is exposed to the pressure of the potting material with the effect that the core, wire and termination is possibly damaged by this pressure and so the electrical as well as the mechanical characteristics are endanger to be affected. After the potting material is cured, the core, wire and termination of the product have to be checked if any reduced electrical or mechanical functions or destructions have occurred.The responsibility for the applicability of customer specific products and use in a particular customer design is always within the authority of the customer. All technical specifications for standard products do also apply for customer specific products.Cleaning solvents which are used to clean the application might damage or change the characteristics of the component.Direct mechanical impact to the product shall be prevented as the ferrite material of the core could flake or in the worst case it could break. Product specific:Follow all instructions mentioned in the datasheet, especially:•The soldering profile has to be complied with according to the technical reflow soldering specification, otherwise no warranty will be su-stained.•All products are supposed to be used before the end of the period of 12 months based on the transfer of title, if not a 100% solderability can´t be warranted.•Violation of the technical product specifications such as exceeding the nominal rated current will result in the loss of warranty.1. General Customer ResponsibilitySome goods within the product range of Würth Elektronik eiSos GmbH & Co. KG contain statements regarding general suitability for certain application areas. These statements about suitability are based on our knowledge and experience of typical requirements concerning the are-as, serve as general guidance and cannot be estimated as binding statements about the suitability for a customer application. The responsibi-lity for the applicability and use in a particular customer design is always solely within the authority of the customer. Due to this fact it is up to the customer to evaluate, where appropriate to investigate and decide whether the device with the specific product characteristics described in the product specification is valid and suitable for the respective customer application or not.2. Customer Responsibility related to Specific, in particular Safety-Relevant ApplicationsIt has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the usual lifetime can-not be completely eliminated in the current state of the art, even if the products are operated within the range of the specifications.In certain customer applications requiring a very high level of safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health it must be ensured by most advanced technological aid of suitable design of the customer application that no injury or damage is caused to third parties in the event of malfunction or failure of an electronic component.3. Best Care and AttentionAny product-specific notes, warnings and cautions must be strictly observed.4. Customer Support for Product SpecificationsSome products within the product range may contain substances which are subject to restrictions in certain jurisdictions in order to serve spe-cific technical requirements. Necessary information is available on request. In this case the field sales engineer or the internal sales person in charge should be contacted who will be happy to support in this matter.5. Product R&DDue to constant product improvement product specifications may change from time to time. As a standard reporting procedure of the Product Change Notification (PCN) according to the JEDEC-Standard inform about minor and major changes. In case of further queries regarding the PCN, the field sales engineer or the internal sales person in charge should be contacted. The basic responsibility of the customer as per Secti-on 1 and 2 remains unaffected.6. Product Life CycleDue to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a stan-dard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage about inevitable product discontinuance. According to this we cannot guarantee that all products within our product range will always be available. Therefore it needs to be verified with the field sales engineer or the internal sales person in charge about the current product availability ex-pectancy before or when the product for application design-in disposal is considered.The approach named above does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.7. Property RightsAll the rights for contractual products produced by Würth Elektronik eiSos GmbH & Co. KG on the basis of ideas, development contracts as well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer will remain with Würth Elektronik eiSos GmbH & Co. KG.8. General Terms and ConditionsUnless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms and Conditions of Würth Elektronik eiSos Group”, last version available at .J Important Notes:The following conditions apply to all goods within the product range of Würth Elektronik eiSos GmbH & Co. KG:分销商库存信息: WURTH-ELECTRONICS 744225S。
744823422;中文规格书,Datasheet资料
Bezeichnung :description :33%+25°C1500 V,50 Hz 5mA , 2 sec.Sockel / base:Draht / wire:Verguß / molding:MSTVersion 808-01-11SSt Version 506-09-26MST Version 404-10-11MST Version 304-06-22MSTVersion 203-12-01MST Version 103-07-03NameÄnderung / modificationDatum / dateWürth Elektronik........................................................................F Werkstoffe & Zulassungen / material & approvalsG Eigenschaften / general specifications :UL94V-0Klimabeständigkeit/ climatic class: 40/125/21UL94V-02UEWF (155°C)Freigabe erteilt / general release:Kunde / customerUL94V-2Abstandhalter / spacer:Datum / date..........................................................................Unterschrift / signatureKontrolliert / approvedWürth Elektronik eiSos GmbH & Co. KGD-74638 Waldenburg · Max-Eyth-Strasse 1 -3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Geprüft / checked ..................................................................................................................................................Spezifikation für Freigabe / specification for releaseKunde / customer :STROMKOMPENSIERTE DROSSEL WE-CMB COMMON MODE CHOKE WE-CMBArtikelnummer / part number :744823422WAYNE KERR WK3260B/WK3265 für/for L 0/L N und/and RDC E Testbedingungen / test conditions :D Prüfgeräte / test equipment :Luftfeuchtigkeit / humidity:Umgebungstemperatur / temperature: Prüfspannung / testing voltageHP 34401 A für/for I NBetriebstemp. / operating temperature: -40°C - + 125°C Übertemperatur / temperature rise: < 55 K It is recommended that the temperature of the part does not exceed 125°C under worst case operating conditions.This electronic component has been designed and developed for usage in general electronic equipment. Before incorporating this component into any equipment where higher safety andreliability is especially required or if there is the possibility of direct damage or injury to human body, for example in the range of aerospace, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc, Würth Elektronik eiSos GmbH must be informed before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.SEITE 1 VON 1/分销商库存信息: WURTH-ELECTRONICS 744823422。
744762182A;中文规格书,Datasheet资料
Bezeichnung :description :Größe / size 1008A 2,5 ± 0,2mmB 2,0 ± 0,2mmC 1,6 ± 0,2mmD 0,5 ref.mm F 0,5 ± 0,1mm H 2,2mm I 0,9mm J1,2mm60 … 70%25°CKeramik/ ceramic AWe Version 104-10-11NameÄnderung / modificationDatum / dateWürth ElektronikENA 5071B für/for SRFD Prüfgeräte / test equipment:Agilent 4287A + HP 16193A für/for L und/and Q HP 4338B für/for R DCHP 4285A + 42841A + 42842C + 42851-6110 für/for IDC Lagerbedingungen / storage conditions: -10°C ~ + 40°C 30 ~ 70% RHF Werkstoffe & Zulassungen / material & approvals:A Mechanische Abmessungen / dimensions:Kunde / customer:744762182AKeramik-SMD-Induktivität WE-KI Ceramic-SMD-Inductor WE-KIArtikelnummer / part number :D-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Geprüft / checked Betriebstemperatur / operating temperature: -40°C ~ +125°C Kunde / customerFreigabe erteilt / general release:...................................................................................................................................................................................................Spezifikation für Freigabe / specification for releaseDATUM / DATE : 2004-10-11Datum / date.............................................................................Unterschrift / signatureKontrolliert / approvedWürth Elektronik eiSos GmbH & Co. KGKontaktmaterial / contact plating:Mo/Mn + Ni + AuBasismaterial / base material: E Testbedingungen / test conditions:Umgebungstemperatur / ambient temperature: -40°C ~ + 110°C Luftfeuchtigkeit / humidity:Umgebungstemperatur / temperature:G Eigenschaften / general specifications:This electronic component is designed and developed with the intention for use in general electronics equipments. Before incorporating the components into any equipments in the field such asaerospace, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc. where higher safety and reliability are especially required or if there is possibility of direct damage or injury to human body. In addition, even electronic component in general electronic equipments, when us electrical circuits that require high safety, reliability functions or performance, the sufficient reliability evaluation-check for the safety must be performed before use. It is essential to give consideration when to install a protective circuit at the design stageRoHS compliantLFSEITE 1 VON 1/分销商库存信息: WURTH-ELECTRONICS 744762182A。
74477510;中文规格书,Datasheet资料
Bezeichnung :description := Start of winding Marking = Inductance code33% Umgebungstemperatur / temperature:+20°CFerritMST 04-10-11NameDatum / dateÄnderung / modificationVersion 1..............................................................................................................................................................................................................................................Würth ElektronikHP 4274 A für/for L und/and Q HP 34401 A für/for R DC und I DCD Prüfgeräte / test equipment:74477510SPEICHERDROSSEL WE-PD2POWER-CHOKE WE-PD2Artikelnummer / part number :Würth Elektronik eiSos GmbH & Co.KGD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Geprüft / checked Umgebungstemp. / ambient temperature: -40°C - + 85°C Basismaterial / base material: Datum / date..............................................................................Unterschrift / signature Kontrolliert / approvednot exceed 125°C under worst case operating conditionsF Werkstoffe & Zulassungen / material & approvals:Endoberfläche / finishing electrode:Draht / wire:Sn/Cu - 99,3/0,7%2UEWF 155°CG Eigenschaften / general specifications:Betriebstemp. / operating temperature: -40°C - + 125°C Kunde / customerFreigabe erteilt / general release:E Testbedingungen / test conditions:Luftfeuchtigkeit / humidity:It is recommended that the temperature of the part does RoHS compliantLFdescription :MST 04-10-11NameDatum / dateÄnderung / modificationVersion 1Würth Elektronik eiSos GmbH & Co.KGD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Datum / dateUnterschrift / signature Würth ElektronikH Induktivitätskurve / Inductance curve :Freigabe erteilt / general release:..............................................................................................................................................................Geprüft / checked Kontrolliert / approvedKunde / customer..............................................................................................................................................................POWER-CHOKE WE-PD2DATUM / DATE : 2004-10-11description :a 330,0± 0,5mmb 20,20± 0,1mm+ 0,5- 1,0d 100,0± 1,0mmMST 04-10-11NameDatum / dateÄnderung / modificationVersion 1mm 13,00c POWER-CHOKE WE-PD2Rollenspezifikation / Reel specification:Freigabe erteilt / general release:Kunde / customer..............................................................................................................................................................Datum / dateUnterschrift / signature Würth Elektronik..............................................................................................................................................................Würth Elektronik eiSos GmbH & Co.KGD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Geprüft / checked Kontrolliert / approvedThe force for tearing off cover tape is 20 to 70 grams in arrow directionfeeding directionThis electronic component is designed and developed with the intention for use in general electronics equipments. Before incorporating the components into any equipments in the field such as aerospace, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc. where higher safety and reliability are especially required or if there is possibility of direct damage or injury to human body. In addition, even electronic component in general electronic equipments, when used in electrical circuits that require high safety, reliability functions or performance, the sufficient reliability evaluation-check for the safety must be performed before use. It is essential to give consideration when to install a protective circuit at the design stage分销商库存信息: WURTH-ELECTRONICS 74477510。
744777239;中文规格书,Datasheet资料
description :33% Umgebungstemperatur / temperature:+20°C100% SnMST04-10-11JH 00-12-06NameDatum / dateD-74638 Waldenburg · Max-Eyth-Straße 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Geprüft / checked Änderung / modification.................................................................................................Kontrolliert / approvedWürth Elektronik eiSos GmbH & Co.KGE Testbedingungen / test conditions :Freigabe erteilt / general release:Kunde / customerWürth Elektronik........................................................................Umgebungstemp. / ambient temperature: -40°C - + 85°C Basismaterial / base material: Endoberfläche / finishing electrode:G Eigenschaften / general specifications :D Prüfgeräte / test equipment :Betriebstemp. / operating temperature: -40°C - + 125°C Luftfeuchtigkeit / humidity:HP 4274 A für/for L und/and Q HP 34401 A für/for I DC und/and R DCF Werkstoffe & Zulassungen / material & approvals :POWER-CHOKE WE-PDVersion 1Version 2 Datum / dateIt is recommended that the temperature of the part does not exceed 125°C under worst case operating conditions...............................................................................Unterschrift / signature Draht / wire:2SFBW 155°CAnbindung an Elektrode / soldering wire to plating:Sn/Ag/Cu - 96.5/3.0/0.5%Ferrit/ferritedescription :POWER-CHOKE WE-PDDATUM / DATE : 2004-10-11H Induktivitätskurve / Inductance curve :MST04-10-11JH 00-12-06NameDatum / dateVersion 2Version 1Würth ElektronikFreigabe erteilt / general release:Kunde / customerDatum / dateUnterschrift / signature .....................................................................................................................................................................................................Würth Elektronik eiSos GmbH & Co.KGÄnderung / modification..................................................Geprüft / checked Kontrolliert / approvedD-74638 Waldenburg · Max-Eyth-Straße 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400description :POWER-CHOKE WE-PD..........................................................................................................................................................MST04-10-11.................................................................................................JH 00-12-06NameDatum / dateVersion 1Version 2 Kunde / customerWürth ElektronikKontrolliert / approvedUnterschrift / signature Datum / dateGeprüft / checked Freigabe erteilt / general release:Änderung / modificationWürth Elektronik eiSos GmbH & Co.KGD-74638 Waldenburg · Max-Eyth-Straße 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400The force for tearing off cover tape is 10 to 130 grams in arrow direction165 to 180°feeding directionThis electronic component is designed and developed with the intention for use in general electronics equipments. Before incorporating the components into any equipments in the field such as aerospace, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc. where higher safety and reliability are especially required or if there is possibility of direct damage or injury to human body. In addition, even electronic component in general electronic equipments, when used in electrical circuits that require high safety, reliability functions or performance, the sufficient reliability evaluation-check for the safety must be performed before use. It is essential to give consideration when to install a protective circuit at the design stage分销商库存信息: WURTH-ELECTRONICS 744777239。
74476012C;中文规格书,Datasheet资料
Bezeichnung :description :Größe / size 0805CA 2,28±0,2mmB 1,70±0,2mmC 1,28±0,2mmD 0,50 ref mm F 0,51 ref mm H 1,78 ref mm I 1,02 ref mm J0,76 ref mmB Elektrische Eigenschaften / electrical properties :Eigenschaften / properties Wert / valueEinheit / unittol.Induktivität /inductance Güte Q /Q factorDC-Widerstand /DC-resistance Nennstrom /rated currentEigenres.-Frequenz /self-res.-frequencyE Testbedingungen / test conditions :Luftfeuchtigkeit / humidity:33% Umgebungstemperatur / temperature:+20°CG Eigenschaften / general specifications :Keramik/ ceramic Lagerbedingungen / Storage conditions: -10°C ~ +40 °C 30 ~70 % RH Betriebstemperatur / operating temperature: -40°C - +125°CHBH Version 411-07-07ES Version 310-08-27SkleVersion 207-01-17SkleVersion 108-03-06Name Änderung / modificationDatum / datektronik eiSos GmbH & Co. KGGermany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400 min.R DCmin.L max.500 MHz∆T = 15 K250 MHz MHz.......................................................................................................................................................................................................Würth ElektronikCeramic-SMD-Inductor WE-KIKontaktmaterial/ contact platingFreigabe erteilt / general release:A Mechanische Abmessungen / dimensions :±5%22nHQ 55Artikelnummer / part number :Geprüft / checked 2600SRFDatum / date...........................................................................Unterschrift / signature Kontrolliert / approvedSpezifikation für Freigabe / specification for releaseDATUM / DATE : 2011-07-07max.mA Testbedingungen / test conditionsKunde / customer :74476012CBasismaterial / base material:F Werkstoffe & Zulassungen / material & approvalsENA 5071B für/for SRFD Prüfgeräte / test equipment :Agilent 4287A +HP 16193A für/for L und/and Q HP 4338B für/for R DCC Lötpad / soldering spec.:Ag + Ni + AuKunde / customer0,22I DC HP 4285A + 42841A + 42842C + 42851 - 6110 für/for I DC 500IJ IHThis electronic component has been designed and developed for usage in general electronic equipment. Before incorporating this component into any equipment where higher safety andreliability is especially required or if there is the possibility of direct damage or injury to human body, for example in the range of aerospace, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc, Würth Elektronik eiSos GmbH must be informed before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.LFAFBDCSEITE 1 VON 1/分销商库存信息: WURTH-ELECTRONICS 74476012C。
7448700015;中文规格书,Datasheet资料
description :A mmB mmC mmD mmE mmEigenschaften / properties Wert / valueEinheit / unittol.Induktivität (je Wicklg.) /inductance (each wdg.)DC-Widerstand (je Wicklg.) /DC-resistance (each wdg)DC-Widerstand (je Wicklg.) /DC-resistance (each wdg)Nennstrom (je Wicklg.) /rated Current (each wdg.)Sättigungsstrom (je Wicklg.) /saturation current (each wdg.)Eigenres.-Frequenz /self-res.-fequency Nennspannung /rated voltage33% Umgebungstemperatur / temperature:+20°CFerrit/ ferrite Betriebstemp. / operating temperature: -40°C - + 125°C Umgebungstemp. / ambient temperature: -40°C - + 85°C It is recommended that the temperature of the part does not exceed 125°C under worst case operating conditions.OO 09-08-14NameDatum / dateV80,0U DC..................................................................................4,9 ± 0,21,5 ± 0,2Typ XLÄnderung / modificationVersion 112,5 max.7,3 ± 0,58,5 max.max.Freigabe erteilt / general release:Kunde / customerhttp://www.we-online.deDatum / dateUnterschrift / signature Kontrolliert / approvedF Werkstoffe & Zulassungen / material & approvals:G Eigenschaften / general specifications:E Testbedingungen / test conditions:HP 4274 A für/for L und/and Q D Prüfgeräte / test equipment:Basismaterial / base material:HP 34401 A für/for I DC und/and R DC...........................................................................................Würth Elektronik................................................................................Draht / wire:2 SFBW; 155°CC Lötpad / soldering spec.:B Elektrische Eigenschaften / electrical properties:Luftfeuchtigkeit / humidity:Würth Elektronik eiSos GmbH & Co. KGD-74638 Waldenburg · Max-Eyth-Strasse 1 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Geprüft / checked DATUM / DATE : 2009-08-01max.Testbedingungen / test conditions 0,016±30%POWER-CHOKE WE-DDµH L 1,L 2 A Mechanische Abmessungen / dimensions:100 kHz / 0,25V1,5@ 20°C 60,00R DC1,2 max ΔL/Lo = -10%I N1,I N2@ 20°C R DC1,2 typ SRF Ωtyp.17,50typ.max.Ω0,0128,60A MHz ΔT = 40 K typ.I sat A 123 L14 L2Start FinishA BCD E1243A[ mm ]1,03,856,113,83,852,5description :OO 09-08-14NameDatum / dateVersion 1DATUM / DATE : 2009-08-01H Induktivitätskurve / Inductance curve:Freigabe erteilt / general release:Kunde / customerPOWER-CHOKE WE-DDWürth Elektronik.............................................................................................................................................................................................................................................................Datum / dateUnterschrift / signature http://www.we-online.deGeprüft / checked Kontrolliert / approvedWürth Elektronik eiSos GmbH & Co. KGD-74638 Waldenburg · Max-Eyth-Strasse 1 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Änderung / modification0,000,200,400,600,801,001,201,401,600,05,010,015,020,025,0L (µH )Current (A)Induktivität vs Strom (typ.)/ Inductance vs Current (typ.)description :I Rollenspezifikation / tape and reel specification:A 12,5± 0,1mmB 16,0± 0,1mmC 24,0± 0,3mm+ 0,1- 0,0E 4,00± 0,1mm F 2,00± 0,1mm G 1,75± 0,1mm H 11,5± 0,1mm I 12,6± 0,1mm J 8,50± 0,1mm T 0,40± 0,05mma 330,0± 2,0mmb 21,00± 0,8mm c 13,00± 0,5mm d 100,0± 1,0mmOO 09-08-14NameDatum / dateÄnderung / modificationVersion 1POWER-CHOKE WE-DDDATUM / DATE : 2009-08-01Gurtspezifikation / Tape specification: Rollenspezifikation / Reel specification:Unterschrift / signature mm1,50D Würth ElektronikFreigabe erteilt / general release:Kunde / customer..................................................................................................................................................................Würth Elektronik eiSos GmbH & Co. KGD-74638 Waldenburg · Max-Eyth-Strasse 1 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400http://www.we-online.de...........................................................................................Geprüft / checked Kontrolliert / approvedDatum / dateThe force for tearing off cover tape is 20 to 70 grams in arrow direction150°feeding directionThis electronic component has been designed and developed for usage in general electronic equipment. Before incorporating this component into any equipment where higher safety and reliability is especially required or if there is the possibility of direct damage or injury to human body, for example in the range of aerospace, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportationsignal, disaster prevention, medical, public information network etc, Würth Elektronik eiSos GmbH must be informed before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.FEøDA BCHGITJØ cadb分销商库存信息: WURTH-ELECTRONICS 7448700015。
744710210;中文规格书,Datasheet资料
3.1 3.0 2.02012-06-272012-05-022006-11-23SStSStRStSStCZWürth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyTel. +49 (0) 79 42 945 - 0A Dimensions: [mm]F Typical Impedance Characteristics:H4: Classification Wave Soldering Profile:H5: Classification Wave ProfileProfile FeaturePreheat- Temperature Min (T smin )- Temperature Typical (T stypical ) - Temperature Max (T smax ) - Time (t s ) from (T smin to T smax )Δ preheat to max Temperature Peak temperature (T p )Time of actual peak temperature (t p )Ramp-down rate - Min - Typical - MaxTime 25°C to 25°C Pb-Free Assembly 100°C 120°C 130°C 70 seconds 150°C max.250°C - 260°C max. 10 secondsmax. 5 second each wave ~ 2 K/s ~ 3.5 K/s ~ 5 K/s 4 minutesSn-Pb Assembly 100°C 120°C 130°C 70 seconds 150°C max.235°C - 260°C max. 10 secondsmax. 5 second each wave ~ 2 K/s ~ 3.5 K/s ~ 5 K/s 4 minutesrefer to EN 61760-1:2006H Soldering Specifications:I Cautions and Warnings:The following conditions apply to all goods within the product series of WE-SDof Würth Elektronik eiSos GmbH & Co. KG:General:All recommendations according to the general technical specifications of the data-sheet have to be complied with.The disposal and operation of the product within ambient conditions which probably alloy or harm the wire isolation has to be avoided.If the product is potted in customer applications, the potting material might shrink during and after hardening. Accordingly to this the product is exposed to the pressure of the potting material with the effect that the core, wire and termination is possibly damaged by this pressure and so the electrical as well as the mechanical characteristics are endanger to be affected. After the potting material is cured, the core, wire and termination of the product have to be checked if any reduced electrical or mechanical functions or destructions have occurred.The responsibility for the applicability of customer specific products and use in a particular customer design is always within the authority of the customer. All technical specifications for standard products do also apply for customer specific products.Washing varnish agent that is used during the production to clean the application might damage or change the characteristics of the wire in-sulation, the marking or the plating. The washing varnish agent could have a negative effect on the long turn function of the product.Direct mechanical impact to the product shall be prevented as the ferrite material of the core could flake or in the worst case it could break. Product specific:Follow all instructions mentioned in the datasheet, especially:•The solder profile has to be complied with according to the technical wave soldering specification, otherwise no warranty will be sustai-ned.•All products are supposed to be used before the end of the period of 12 months based on the product date-code, if not a 100% solderabi-lity can´t be warranted.•Violation of the technical product specifications such as exceeding the nominal rated current will result in the loss of warranty.1. General Customer ResponsibilitySome goods within the product range of Würth Elektronik eiSos GmbH & Co. KG contain statements regarding general suitability for certain application areas. These statements about suitability are based on our knowledge and experience of typical requirements concerning the are-as, serve as general guidance and cannot be estimated as binding statements about the suitability for a customer application. The responsibi-lity for the applicability and use in a particular customer design is always solely within the authority of the customer. Due to this fact it is up to the customer to evaluate, where appropriate to investigate and decide whether the device with the specific product characteristics described in the product specification is valid and suitable for the respective customer application or not.2. Customer Responsibility related to Specific, in particular Safety-Relevant ApplicationsIt has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the usual lifetime can-not be completely eliminated in the current state of the art, even if the products are operated within the range of the specifications.In certain customer applications requiring a very high level of safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health it must be ensured by most advanced technological aid of suitable design of the customer application that no injury or damage is caused to third parties in the event of malfunction or failure of an electronic component.3. Best Care and AttentionAny product-specific notes, warnings and cautions must be strictly observed.4. Customer Support for Product SpecificationsSome products within the product range may contain substances which are subject to restrictions in certain jurisdictions in order to serve spe-cific technical requirements. Necessary information is available on request. In this case the field sales engineer or the internal sales person in charge should be contacted who will be happy to support in this matter.5. Product R&DDue to constant product improvement product specifications may change from time to time. As a standard reporting procedure of the Product Change Notification (PCN) according to the JEDEC-Standard inform about minor and major changes. In case of further queries regarding the PCN, the field sales engineer or the internal sales person in charge should be contacted. The basic responsibility of the customer as per Secti-on 1 and 2 remains unaffected.6. Product Life CycleDue to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a stan-dard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage about inevitable product discontinuance. According to this we cannot guarantee that all products within our product range will always be available. Therefore it needs to be verified with the field sales engineer or the internal sales person in charge about the current product availability ex-pectancy before or when the product for application design-in disposal is considered.The approach named above does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.7. Property RightsAll the rights for contractual products produced by Würth Elektronik eiSos GmbH & Co. KG on the basis of ideas, development contracts as well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer will remain with Würth Elektronik eiSos GmbH & Co. KG.8. General Terms and ConditionsUnless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms and Conditions of Würth Elektronik eiSos Group”, last version available at .J Important Notes:The following conditions apply to all goods within the product range of Würth Elektronik eiSos GmbH & Co. KG:分销商库存信息: WURTH-ELECTRONICS 744710210。
7448640404;中文规格书,Datasheet资料
description :Gehäuse / case: ETA 21,2 max mmB 21,2 max mmC 17,8 max mmD 13,0 ± 0,2mmE 10,0 ± 0,2mmF 4,5 max mm ø0,8 typmm33%20 °C2000 V,50 HzMST Version 109-08-06NameÄnderung / modificationDatum / dateWAYNE KERR WK3260B/WK3265 für/for L 0 und/and R DC Luftfeuchtigkeit / humidity:A Mechanische Abmessungen / dimensions :CURRENT-COMPENSATED CHOKE WE-FCKlimabeständigkeit/ climatic class: 40/125/21Kern / coreP155 IEC317-20Betriebstemp. / operating temperature: -25°C - + 125°C Übertemperatur / temperature rise: < 55 K DATUM / DATE : 2009-08-06Datum / date..................................................................................Unterschrift / signatureKontrolliert / approvedWürth Elektronik eiSos GmbH & Co. KGD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Geprüft / checked ...............................................................................................................................................D Prüfgeräte / test equipment:E Testbedingungen / test conditions:Prüfspannung / isolation voltageHP 34401 A für/for INUmgebungstemperatur / temperature:Würth Elektronik..................................................................................G Eigenschaften / general specifications:Gehäuse / case:Draht / wire:UL94V-0 F Werkstoffe & Zulassungen / material & approvals:MnZn-Ferrite / MnZn ferriteIt is recommended that the temperature of the part does not exceed 125°C under worst case operating conditions.Freigabe erteilt / general release:Kunde / customerThis electronic component has been designed and developed for usage in general electronic equipment. Before incorporating this component into any equipment where higher safety and reliability is especially required or if there is the possibility of direct damage or injury to human body, for example in the range of aerospace, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc, Würth Elektronik eiSos GmbH must be informed before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.1234description :MST Version 109-08-06NameÄnderung / modificationDatum / dateH Einfügungsdämpfung / insertion loss:Geprüft / checked Kontrolliert / approvedWürth Elektronik eiSos GmbH & Co. KGD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Geprüft / checked Kontrolliert / approved Datum / date ..................................................................................CURRENT-COMPENSATED CHOKE WE-FCDATUM / DATE : 2009-08-06common mode This electronic component has been designed and developed for usage in general electronic equipment. Before incorporating this component into any equipment where higher safety and reliability is especially required or if there is the possibility of direct damage or injury to human body, for example in the range of aerospace, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc, Würth Elektronik eiSos GmbH must be informed before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.description :Stangenspezifikation / tube specification:L 525mm H 31mm B 24,5mm Menge: 23 Stück/Stange quantity: 23 pieces/tube....................................................................................................................................................................MSTVersion 109-08-06Name Änderung / modificationDatum / dateWürth ElektronikFreigabe erteilt / general release:Kunde / customer..................................................................................Geprüft / checked DATUM / DATE : 2009-08-06I Stangenspezifikation / tube specification:Datum / dateKontrolliert / approvedD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Würth Elektronik eiSos GmbH & Co. KGUnterschrift / signature CURRENT-COMPENSATED CHOKE WE-FC............................................................This electronic component has been designed and developed for usage in general electronic equipment. Before incorporating this component into any equipment where higher safety and reliability is especially required or if there is the possibility of direct damage or injury to human body, for example in the range of aerospace, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc, Würth Elektronik eiSos GmbH must be informed before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.分销商库存信息: WURTH-ELECTRONICS 7448640404。
744227;中文规格书,Datasheet资料
8.1 8.0 7.02012-07-172012-07-172004-10-11SStSStMSTSStSBaWürth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyTel. +49 (0) 79 42 945 - 0A Dimensions: [mm]F Typical Impedance Characteristics:H1: Classification Reflow Profile for SMT components:H2: Classification Reflow ProfilesProfile FeaturePreheat- Temperature Min (T smin ) - Temperature Max (T smax ) - Time (t s ) from (T smin to T smax )Ramp-up rate (T L to T P )Liquidous temperature (T L )Time (t L ) maintained above T L Peak package body temperature (T p )Time within 5°C of actual peak temperature (t p )Ramp-down rate (T P to T L )Time 25°C to peak temperature Pb-Free Assembly 150°C 200°C60-180 seconds 3°C/ second max.217°C60-150 seconds See Table H320-30 seconds 6°C/ second max.8 minutes max.refer to IPC/JEDEC J-STD-020DH3: Package Classification Reflow TemperaturePB-Free Assembly PB-Free Assembly PB-Free Assembly Package Thickness< 1.6 mm 1.6 - 2.5 mm ≥ 2.5 mmVolume mm³<350260°C 260°C 250°CVolume mm³350 - 2000260°C 250°C 245°CVolume mm³>2000260°C 245°C 245°Crefer to IPC/JEDEC J-STD-020DH Soldering Specifications:I Cautions and Warnings:The following conditions apply to all goods within the product series of WE-SL2of Würth Elektronik eiSos GmbH & Co. KG:General:All recommendations according to the general technical specifications of the data sheet have to be complied with.The disposal and operation of the product within ambient conditions which probably alloy or harm the wire isolation has to be avoided.If the product is potted in customer applications, the potting material might shrink during and after hardening. Accordingly to this the product is exposed to the pressure of the potting material with the effect that the core, wire and termination is possibly damaged by this pressure and so the electrical as well as the mechanical characteristics are endanger to be affected. After the potting material is cured, the core, wire and termination of the product have to be checked if any reduced electrical or mechanical functions or destructions have occurred.The responsibility for the applicability of customer specific products and use in a particular customer design is always within the authority of the customer. All technical specifications for standard products do also apply for customer specific products.Cleaning solvents which are used to clean the application might damage or change the characteristics of the component.Direct mechanical impact to the product shall be prevented as the ferrite material of the core could flake or in the worst case it could break. Product specific:Follow all instructions mentioned in the datasheet, especially:•The soldering profile has to be complied with according to the technical reflow soldering specification, otherwise no warranty will be su-stained.•All products are supposed to be used before the end of the period of 12 months based on the transfer of title, if not a 100% solderability can´t be warranted.•Violation of the technical product specifications such as exceeding the nominal rated current will result in the loss of warranty.1. General Customer ResponsibilitySome goods within the product range of Würth Elektronik eiSos GmbH & Co. KG contain statements regarding general suitability for certain application areas. These statements about suitability are based on our knowledge and experience of typical requirements concerning the are-as, serve as general guidance and cannot be estimated as binding statements about the suitability for a customer application. The responsibi-lity for the applicability and use in a particular customer design is always solely within the authority of the customer. Due to this fact it is up to the customer to evaluate, where appropriate to investigate and decide whether the device with the specific product characteristics described in the product specification is valid and suitable for the respective customer application or not.2. Customer Responsibility related to Specific, in particular Safety-Relevant ApplicationsIt has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the usual lifetime can-not be completely eliminated in the current state of the art, even if the products are operated within the range of the specifications.In certain customer applications requiring a very high level of safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health it must be ensured by most advanced technological aid of suitable design of the customer application that no injury or damage is caused to third parties in the event of malfunction or failure of an electronic component.3. Best Care and AttentionAny product-specific notes, warnings and cautions must be strictly observed.4. Customer Support for Product SpecificationsSome products within the product range may contain substances which are subject to restrictions in certain jurisdictions in order to serve spe-cific technical requirements. Necessary information is available on request. In this case the field sales engineer or the internal sales person in charge should be contacted who will be happy to support in this matter.5. Product R&DDue to constant product improvement product specifications may change from time to time. As a standard reporting procedure of the Product Change Notification (PCN) according to the JEDEC-Standard inform about minor and major changes. In case of further queries regarding the PCN, the field sales engineer or the internal sales person in charge should be contacted. The basic responsibility of the customer as per Secti-on 1 and 2 remains unaffected.6. Product Life CycleDue to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a stan-dard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage about inevitable product discontinuance. According to this we cannot guarantee that all products within our product range will always be available. Therefore it needs to be verified with the field sales engineer or the internal sales person in charge about the current product availability ex-pectancy before or when the product for application design-in disposal is considered.The approach named above does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.7. Property RightsAll the rights for contractual products produced by Würth Elektronik eiSos GmbH & Co. KG on the basis of ideas, development contracts as well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer will remain with Würth Elektronik eiSos GmbH & Co. KG.8. General Terms and ConditionsUnless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms and Conditions of Würth Elektronik eiSos Group”, last version available at .J Important Notes:The following conditions apply to all goods within the product range of Würth Elektronik eiSos GmbH & Co. KG:分销商库存信息: WURTH-ELECTRONICS 744227。
0878324422;中文规格书,Datasheet资料
This document was generated on 08/16/2012PLEASE CHECK FOR LATEST PART INFORMATIONPart Number:87832-4422Status:ActiveOverview:Milli-Grid™ Connector SystemDescription:2.00mm Pitch Milli-Grid™ Header, Surface Mount, Vertical, Shrouded, Lead-Free, 44Circuits, 0.38µm Gold (Au) Plating, Pick-and-Place Cap, with Locking Windows and Center Polarization Slot, PCB Locator, TubeDocuments:3D ModelProduct Specification PS-87831-027 (PDF)Drawing (PDF)RoHS Certificate of Compliance (PDF)Agency CertificationCSA LR19980ULE29179GeneralProduct Family PCB Headers Series87832Application Signal, Wire-to-BoardComments With Cap|Contact Molex for application in automotive industryOverviewMilli-Grid™ Connector System Product Name Milli-Grid™UPC822348352340PhysicalBreakawayNo Circuits (Loaded)44Circuits (maximum)44Color - ResinBlack Durability (mating cycles max)100First Mate / Last Break No Flammability94V-0Glow-Wire Compliant No Guide to Mating Part No Keying to Mating Part Yes Lock to Mating Part YesMaterial - MetalPhosphor Bronze Material - Plating MatingGold Material - Plating Termination Tin Material - Resin Nylon Net Weight2.105/g Number of Rows 2Orientation Vertical PCB Locator No PCB Retention None Packaging TypeTube Pitch - Mating Interface2.00mm Pitch - Termination Interface 2.00mm Plating min - Mating0.381µm Plating min - Termination 1.905µm Polarized to PCB No Shrouded Fully StackableNo Surface Mount Compatible (SMC)YesTemperature Range - Operating-55°C to +105°CSeriesimage - Reference onlyEU RoHSChina RoHSELV and RoHS Compliant REACH SVHCContains SVHC: No Low-Halogen Status Not Low-HalogenNeed more information on product environmental compliance?Email productcompliance@For a multiple part number RoHS Certificate of Compliance, click herePlease visit the Contact Us section for any non-product compliance questions.Search Parts in this Series 87832SeriesMates With50394 Wire-to-Board Terminals, 51110Wire-to-Board Crimp Housing, 87568 Wire-to-Board IDT Housings, 79107 Board-to-Board Top Entry Through Hole Receptacle,79108 Board-to-Board FFC/FPC Top Entry Through Hole Receptacle, LTermination Interface: Style Through Hole and Surface MountElectricalCurrent - Maximum per Contact2AVoltage - Maximum125VSolder Process DataDuration at Max. Process Temperature (seconds)10Lead-free Process Capability Reflow Capable (SMT only)Max. Cycles at Max. Process Temperature1Process Temperature max. C260Material InfoReference - Drawing NumbersProduct Specification PS-87831-027Sales Drawing SD-87832-006This document was generated on 08/16/2012PLEASE CHECK FOR LATEST PART INFORMATION分销商库存信息: MOLEX 0878324422。
744758410A;中文规格书,Datasheet资料
Bezeichnung :description :Größe / size 1008A 2,6 ± 0,2mmB 2,1 ± 0,2mmC 1,7 ± 0,2mmD 0,7 ref.mm F 0,5 ± 0,1mm H 2,2 ref.mm I 0,9 ref.mm J1,2 ref.mm60 … 70%25°CFerrit/ Ferrite SKLEVersion 107-11-28Name Änderung / modificationDatum / dateUmgebungstemperatur / ambient temperature: -40°C ~ +70°C Luftfeuchtigkeit / humidity:Umgebungstemperatur / temperature:G Eigenschaften / general specifications:Basismaterial / base material: E Testbedingungen / test conditions:Kontaktmaterial / contact plating:Ag/Pd + Ni + SnSpezifikation für Freigabe / specification for releaseDATUM / DATE : 2007-11-28Datum / date...............................................................................Unterschrift / signature Kontrolliert / approvedWürth Elektronik eiSos GmbH & Co. KGD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Geprüft / checked Betriebstemperatur / operating temperature: -40°C ~ +85°C Kunde / customerFreigabe erteilt / general release:...............................................................................................................................................................................................................Kunde / customerHigh Current RF-Inductor WE-RFHA Mechanische Abmessungen / dimensions:Würth ElektronikENA 5071B für/for SRFD Prüfgeräte / test equipment:Agilent E4991A + 16197A für/for L und/and Q HP 4338B für/for R DCHP 4285A + 42841A + 42842C + 42851-6110 für/for I DC Lagerbedingungen / storage conditions: -10°C ~ +40°C 20 ~ 70% RHF Werkstoffe & Zulassungen / material & approvals:This electronic component has been designed and developed for usage in general electronic equipment. Before incorporating this component into any equipment where higher safety and reliability is especially required or if there is the possibility of direct damage or injury to human body, for example in the range of aerospace, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc, Würth Elektronik eiSos GmbH must be informed before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.SEITE 1 VON 1/分销商库存信息: WURTH-ELECTRONICS 744758410A。
7448640401;中文规格书,Datasheet资料
description :Gehäuse / case: ETA 21,2 max mmB 21,2 max mmC 17,8 max mmD 13,0 ± 0,2mmE 10,0 ± 0,2mmF 4,5 max mm ø0,8 typmm33%20 °C2000 V,50 HzMST Version 109-08-06NameÄnderung / modificationDatum / dateWAYNE KERR WK3260B/WK3265 für/for L 0 und/and R DC Luftfeuchtigkeit / humidity:A Mechanische Abmessungen / dimensions :CURRENT-COMPENSATED CHOKE WE-FCKlimabeständigkeit/ climatic class: 40/125/21Kern / coreP155 IEC317-20Betriebstemp. / operating temperature: -25°C - + 125°C Übertemperatur / temperature rise: < 55 K DATUM / DATE : 2009-08-06Datum / date..................................................................................Unterschrift / signatureKontrolliert / approvedWürth Elektronik eiSos GmbH & Co. KGD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Geprüft / checked ...............................................................................................................................................D Prüfgeräte / test equipment:E Testbedingungen / test conditions:Prüfspannung / isolation voltageHP 34401 A für/for INUmgebungstemperatur / temperature:Würth Elektronik..................................................................................G Eigenschaften / general specifications:Gehäuse / case:Draht / wire:UL94V-0 F Werkstoffe & Zulassungen / material & approvals:MnZn-Ferrite / MnZn ferriteIt is recommended that the temperature of the part does not exceed 125°C under worst case operating conditions.Freigabe erteilt / general release:Kunde / customerThis electronic component has been designed and developed for usage in general electronic equipment. Before incorporating this component into any equipment where higher safety and reliability is especially required or if there is the possibility of direct damage or injury to human body, for example in the range of aerospace, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc, Würth Elektronik eiSos GmbH must be informed before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.1234description :MST Version 109-08-06NameÄnderung / modificationDatum / dateH Einfügungsdämpfung / insertion loss:Geprüft / checked Kontrolliert / approvedWürth Elektronik eiSos GmbH & Co. KGD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Geprüft / checked Kontrolliert / approved Datum / date ..................................................................................CURRENT-COMPENSATED CHOKE WE-FCDATUM / DATE : 2009-08-06common mode This electronic component has been designed and developed for usage in general electronic equipment. Before incorporating this component into any equipment where higher safety and reliability is especially required or if there is the possibility of direct damage or injury to human body, for example in the range of aerospace, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc, Würth Elektronik eiSos GmbH must be informed before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.description :Stangenspezifikation / tube specification:L 525mm H 31mm B 24,5mm Menge: 23 Stück/Stange quantity: 23 pieces/tube....................................................................................................................................................................MSTVersion 109-08-06Name Änderung / modificationDatum / dateWürth ElektronikFreigabe erteilt / general release:Kunde / customer..................................................................................Geprüft / checked DATUM / DATE : 2009-08-06I Stangenspezifikation / tube specification:Datum / dateKontrolliert / approvedD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Würth Elektronik eiSos GmbH & Co. KGUnterschrift / signature CURRENT-COMPENSATED CHOKE WE-FC............................................................This electronic component has been designed and developed for usage in general electronic equipment. Before incorporating this component into any equipment where higher safety and reliability is especially required or if there is the possibility of direct damage or injury to human body, for example in the range of aerospace, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc, Würth Elektronik eiSos GmbH must be informed before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.分销商库存信息: WURTH-ELECTRONICS 7448640401。
7448资料
7段显示译码器7448是输出高电平有效的译码器，其真值表如表1。
7448/SN7448 引脚功能图工作电压:5V7448除了有实现7段显示译码器基本功能的输入（DCBA）和输出（Ya～Yg）端外，74 48还引入了灯测试输入端（LT）和动态灭零输入端（RBI），以及既有输入功能又有输出功能的消隐输入/动态灭零输出（BI/RBO）端。
由7448真值表可获知7448所具有的逻辑功能：（1）7段译码功能（LT=1，RBI=1）在灯测试输入端（LT）和动态灭零输入端（RBI）都接无效电平时，输入DCBA经7448译码，输出高电平有效的7段字符显示器的驱动信号，显示相应字符。
除DCBA = 0000外，RBI也可以接低电平，见表1中1～16行。
（2）消隐功能（BI=0）此时BI/RBO端作为输入端，该端输入低电平信号时，表1倒数第3行，无论LT 和RBI 输入什么电平信号，不管输入DCBA为什么状态，输出全为“0”，7段显示器熄灭。
该功能主要用于多显示器的动态显示。
（3）灯测试功能（LT = 0）此时BI/RBO端作为输出端，端输入低电平信号时，表1最后一行，与及DCBA输入无关，输出全为“1”，显示器7个字段都点亮。
该功能用于7段显示器测试，判别是否有损坏的字段。
（4）动态灭零功能（LT=1，RBI=1）此时BI/RBO端也作为输出端，LT 端输入高电平信号，RBI 端输入低电平信号，若此时DCBA = 0000，表1倒数第2行，输出全为“0”，显示器熄灭，不显示这个零。
DCBA≠0，则对显示无影响。
该功能主要用于多个7段显示器同时显示时熄灭高位的零。
表1：图2 7段显示译码器7448（a）逻辑图（b）方框图（c）符号图图2给出了7448的逻辑图，方框图和符号图。
由符号图可以知道，4号管脚端具有输入和输出双重功能。
作为输入（BI）低电平时，G21为0，所有字段输出置0，即实现消隐功能。
作为输出（RBO），相当于LT，及CT0的与坟系，即LT=1，RBI=0，DCBA= 0000时输出低电平，可实现动态灭零功能。
7448640410;中文规格书,Datasheet资料
description :Gehäuse / case: UTA 21,2 max mmB 16,6 max mmC 22,5 max mmD 13,0 ± 0,2mmE 10,0 ± 0,2mmF 4,5 max mm ø0,8 typmmEigenschaften /propertiesWert / valueEinheit / unittol.Leerlauf-Induktivität /inductanceDC-Widerstand /DC-resistance Nennstrom /rated current Nennspannung /rated voltage33%20 °C2000 V,50 HzHasAVersion 211-09-01MST Version 109-08-06NameÄnderung / modificationDatum / dateWAYNE KERR WK3260B/WK3265 für/for L 0 und/and R DC Klimabeständigkeit/ climatic class: 40/125/21 Datum / date............................................................................. A Mechanische Abmessungen / dimensions :10 kHz / 100 mV / 20°C B Elektrische Eigenschaften / electrical properties:25050 HzmHR DC VCURRENT-COMPENSATED CHOKE WE-FCKern / coreP155 IEC317-20Betriebstemp. / operating temperature: -25°C - + 125°C Übertemperatur / temperature rise: < 55 K L O 2,70 D Prüfgeräte / test equipment:E Testbedingungen / test conditions:@ 20 °C@ 70 °CDATUM / DATE : 2011-09-01±15%A Testbedingungen / test conditions 1,200,19minC Schaltbild / schematic:Unterschrift / signature Kontrolliert / approvedWürth Elektronik eiSos GmbH & Co. KGD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Geprüft / checked ..........................................................................................................................................Prüfspannung / isolation voltageU NI N Luftfeuchtigkeit / humidity:HP 34401 A für/for INUmgebungstemperatur / temperature:Würth Elektronik..................................................................................G Eigenschaften / general specifications:Gehäuse / case:Freigabe erteilt / general release:Kunde / customerDraht / wire:UL94V-0 F Werkstoffe & Zulassungen / material & approvals:MnZn-Ferrite / MnZn ferriteIt is recommended that the temperature of the part does not exceed 125°C under worst case operating conditions.This electronic component has been designed and developed for usage in general electronic equipment. Before incorporating thi s component into any equipment where higher safety and reliability isespecially required or if there is the possibility of direct damage or injury to human body, for example in the range of aero space, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc, Würth Elektronik eiSos GmbH must be informed before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.1 2N134N21 2 34HasAVersion 211-09-01MST Version 109-08-06NameÄnderung / modificationDatum / dateGeprüft / checked Kontrolliert / approvedWürth Elektronik eiSos GmbH & Co. KGD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400H Einfügungsdämpfung / insertion loss:Geprüft / checkedKontrolliert / approvedDatum / date ..................................................................................= = = = =common modeThis electronic component has been designed and developed for usage in general electronic equipment. Before incorporating thi s component into any equipment where higher safety and reliability is especially required or if there is the possibility of direct damage or injury to human body, for example in the range of aero space, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc, W ürth Elektronik eiSos GmbH must be informed before the design -in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used i n electrical circuits that require high safety and reliability functions or performance.Bezeichnung :description :..................................................................................HasAVersion 211-09-01..................................................................................MSTVersion 109-08-06Name Änderung / modificationDatum / dateKunde / customer..................................................................................Geprüft / checkedSTROMKOMPENSIERTE DROSSEL WE-FC Datum / dateKontrolliert / approvedD-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Würth Elektronik eiSos GmbH & Co. KGUnterschrift / signature Würth ElektronikFreigabe erteilt / general release:CURRENT-COMPENSATED CHOKE WE-FC..................................................................DATUM / DATE : 2011-09-01I Stangenspezifikation / tube specification:This electronic component has been designed and developed for usage in general electronic equipment. Before incorporating thi s component into any equipment where higher safety and reliability is especially required or if there is the possibility of direct damage or injury to human body, for example in the range of aero space, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc, W ürth Elektronik eiSos GmbH must be informed before the design -in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used i n electrical circuits that require high safety and reliability functions or performance.分销商库存信息: WURTH-ELECTRONICS 7448640410。
7444资料
I S S U E : P 1 23/10/027444 S E R I E SThe 7444 series are passive bandpass filters designed for use in signalling, monitoringand supervisory systems where safety is critical and the filter must be stable over therange of temperatures experienced in an unheated, non air-conditioned vehicle exposedto all North American environmental conditions.•The safety critical design feature provides that if any internal component becomesan open or short circuit, the output signal falls by at least 18 dB below normal.•The temperature stability is enhanced by selecting the resonant components suchthat the temperature coefficient of inductance is the inverse of the temperaturecoefficient of capacitance. In addition, the components are subjected to prolongedtemperature cycling, before tuning, so as to minimize the disaccommodationfactor of the ferrite materials.•The filters are hermetically sealed in a plated steel can for long life under a widerange of environmental conditions including high relative humidity.•All filters will tolerate 350 volts peak-to-peak at out of band frequencies.•The filters are PC board mountable with solderable pins in glass to metal seals. Thereare four 8-32 threaded inserts for secure mounting when subjected to vibration.MECHANICAL (All dimensions in inches)An ISO 9001 Registered Company 229 Colonnade Road, Ottawa, Ontario, Canada K2E 7K3 Tel: (613) 226-1626 Fax: (613) 226-7124 ELECTRICAL SPECIFICATIONS @ 25˚C。
7427155;中文规格书,Datasheet资料
6.1 6.0 5.02012-06-272012-04-302007-01-25SStSStSMuSStSMu-Würth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyTel. +49 (0) 79 42 945 - 0A Dimensions: [mm]Additional FeaturesSafety key to lock/ unkock74271D2 General Properties:Ferrite core Ferrite core Ferrite core Plastic housing Plastic housing Test cable Test cablePropertiesMaterial Initial permeability Curie temperatureColourFlammability ClassificationApplicable cable Applicable cable lengthµi T CValue 4 W 620620150Grey UL94-V0AWG26120Unit°Cmm Tol.typ.typ.F Typical Impedance Characteristics:I Cautions and Warnings:The following conditions apply to all goods within the product series of WE-STAR RINGof Würth Elektronik eiSos GmbH & Co. KG:General:All recommendations according to the general technical specifications of the data sheet have to be complied with.The disposal and operation of the product within ambient conditions which probably alloy or harm the component surface has to be avoided.The packaging of the product is to encase the needed humidity of the plastic housing. To ensure the humidity level, the products have to be stored in this delivered packaging. If not, the products are losing their humidity. In this case you can re-condition the components according to the internal standard WE1883 to ensure the necessary humidity in the plastic.To ensure the operating mode of the product, the ambient temperature at processing (when the part will be mounted on the cable) has to be in the range of 15 to 25 °C.Before mounting, the part should be stored for one hour in this condition.The responsibility for the applicability of customer specific products and the use in a particular customer design is always within the authority of the customer. All technical specifications for standard products do also apply for customer specific products.Direct mechanical impact to the product and the forcible closing of this shall be prevented as the ferrite material of the ferrite body or the pla-stic housing could flake or in the worst case it could break.Product specific:Follow all instructions mentioned in the datasheet, especially:•The cable diameter must be pointed out, otherwise no warranty will be sustained.•Violation of the technical product specifications such as exceeding the nominal rated current will result in the loss of warranty.1. General Customer ResponsibilitySome goods within the product range of Würth Elektronik eiSos GmbH & Co. KG contain statements regarding general suitability for certain application areas. These statements about suitability are based on our knowledge and experience of typical requirements concerning the are-as, serve as general guidance and cannot be estimated as binding statements about the suitability for a customer application. The responsibi-lity for the applicability and use in a particular customer design is always solely within the authority of the customer. Due to this fact it is up to the customer to evaluate, where appropriate to investigate and decide whether the device with the specific product characteristics described in the product specification is valid and suitable for the respective customer application or not.2. Customer Responsibility related to Specific, in particular Safety-Relevant ApplicationsIt has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the usual lifetime can-not be completely eliminated in the current state of the art, even if the products are operated within the range of the specifications.In certain customer applications requiring a very high level of safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health it must be ensured by most advanced technological aid of suitable design of the customer application that no injury or damage is caused to third parties in the event of malfunction or failure of an electronic component.3. Best Care and AttentionAny product-specific notes, warnings and cautions must be strictly observed.4. Customer Support for Product SpecificationsSome products within the product range may contain substances which are subject to restrictions in certain jurisdictions in order to serve spe-cific technical requirements. Necessary information is available on request. In this case the field sales engineer or the internal sales person in charge should be contacted who will be happy to support in this matter.5. Product R&DDue to constant product improvement product specifications may change from time to time. As a standard reporting procedure of the Product Change Notification (PCN) according to the JEDEC-Standard inform about minor and major changes. In case of further queries regarding the PCN, the field sales engineer or the internal sales person in charge should be contacted. The basic responsibility of the customer as per Secti-on 1 and 2 remains unaffected.6. Product Life CycleDue to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a stan-dard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage about inevitable product discontinuance. According to this we cannot guarantee that all products within our product range will always be available. Therefore it needs to be verified with the field sales engineer or the internal sales person in charge about the current product availability ex-pectancy before or when the product for application design-in disposal is considered.The approach named above does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.7. Property RightsAll the rights for contractual products produced by Würth Elektronik eiSos GmbH & Co. KG on the basis of ideas, development contracts as well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer will remain with Würth Elektronik eiSos GmbH & Co. KG.8. General Terms and ConditionsUnless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms and Conditions of Würth Elektronik eiSos Group”, last version available at .J Important Notes:The following conditions apply to all goods within the product range of Würth Elektronik eiSos GmbH & Co. KG:分销商库存信息: WURTH-ELECTRONICS 7427155。
7443310100;中文规格书,Datasheet资料
Bezeichnung :description :33%Umgebungstemperatur / temperature:+20°CIron Powder Core Lagertemp. / storage temperature: -40°C - +60°C BD09-11-03Rst 08-11-11NameDatum / dateÄnderung / modificationVersion 1Version 2Luftfeuchtigkeit / humidity:It is recommended that the temperature of the part does HP 34401 A & Fluke 54II für/for I DC; SPEICHERDROSSEL WE-HCC 1210 (Eisenpulver)POWER-CHOKE WE-HCC 1210 (Iron Powder)Artikelnummer / part number :7443310100D-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Geprüft / checked .................................................................................................Basismaterial / base material:Metra HIT 27I für/for R DCArbeitstemperatur / operating temperature: -40°C - +125°C WAYNE KERR 3260B für/for L 0; I SAT D Prüfgeräte / test equipment:E Testbedingungen / test conditions:Kunde / customerF Werkstoffe & Zulassungen / material & approvals:G Eigenschaften / general specifications:not exceed 125°C under worst case operating conditions.Draht / wire:JIS 155°C , UL : E201757Würth Elektronik..................................................................................Freigabe erteilt / general release:http://www.we-online.deDatum / date.............................................................................Unterschrift / signatureKontrolliert / approvedWürth Elektronik eiSos GmbH & Co. KGmarkingBezeichnung :description :H Induktivitätskurve / Inductance curve:BD09-11-03Rst 08-11-11NameDatum / dateSPEICHERDROSSEL WE-HCC 1210 (Eisenpulver)POWER-CHOKE WE-HCC 1210 (Iron Powder)DATUM / DATE : 2009-11-03Freigabe erteilt / general release:Kunde / customer...............................................................................................................................................................Datum / dateUnterschrift / signature Würth ElektronikVersion 2..........................................................................................................................................Version 1D-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400http://www.we-online.deGeprüft / checked Kontrolliert / approvedÄnderung / modificationWürth Elektronik eiSos GmbH & Co. KGBezeichnung :description :I Temperaturanstieg / Temperature rise curve:BD09-11-03Rst 08-11-11NameDatum / dateDATUM / DATE : 2009-11-03Version 1D-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400...............................................................................................................................................................Datum / dateUnterschrift / signaturehttp://www.we-online.deGeprüft / checked Kontrolliert / approvedÄnderung / modificationWürth Elektronik eiSos GmbH & Co. KGSPEICHERDROSSEL WE-HCC 1210 (Eisenpulver)POWER-CHOKE WE-HCC 1210 (Iron Powder)Freigabe erteilt / general release:Kunde / customerWürth ElektronikVersion 2..........................................................................................................................................Bezeichnung :description :BD09-11-03Rst 08-11-11NameDatum / dateSPEICHERDROSSEL WE-HCC 1210 (Eisenpulver)POWER-CHOKE WE-HCC 1210 (Iron Powder)Freigabe erteilt / general release:Kunde / customer...............................................................................................................................................................Datum / dateUnterschrift / signature Würth ElektronikVersion 2............................................................................................................................................Version 1D-74638 Waldenburg · Max-Eyth-Strasse 1 - 3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400Geprüft / checked Kontrolliert / approvedÄnderung / modificationWürth Elektronik eiSos GmbH & Co. KGThe Force for tearing off cover tape is 20 to 70 grams in arrow direction150°feeding directionThis electronic component has been designed and developed for usage in general electronic equipment. Before incorporating this component into any equipment where higher safety and reliability is especially required or if there is the possibility of direct damage or injury to human body, for example in the range of aerospace, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc, Würth Elektronik eiSos GmbH must be informed before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.分销商库存信息: WURTH-ELECTRONICS 7443310100。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
Bezeichnung :description :
33%+25°C
1500 V,50 Hz 5 mA / 2 sec.
MST Version 404-10-11MST Version 304-07-06MST
Version 203-12-01MST Version 1
03-03-07
Name
Änderung / modification
Datum / date
Betriebstemp. / operating temperature: -40°C - + 125°C Übertemperatur / temperature rise: < 55 K It is recommended that the temperature of the part does not exceed 125°C under worst case operating conditions.
Freigabe erteilt / general release:
Kunde / customer
Würth Elektronik
........................................................................
F Werkstoffe & Zulassungen / material & approvals
G Eigenschaften / general specifications :
D Prüfgeräte / test equipment :
Datum / date
..........................................................................Unterschrift / signature
Kontrolliert / approved
Würth Elektronik eiSos GmbH & Co. KG
D-74638 Waldenburg · Max-Eyth-Strasse 1 -3 · Germany · Telefon (+49) (0) 7942 - 945 - 0 · Telefax (+49) (0) 7942 - 945 - 400
Geprüft / checked ..................................................................................................................................................
Spezifikation für Freigabe / specification for release
UL94V-2Abstandhalter / spacer
UL94V-0
Klimabeständigkeit/ climatic class: 40/125/21Sockel / base:UL94V-0Draht / wire:2UEWF (155°C)Kleber / glue:
Kunde / customer :
STROMKOMP. DROSSEL WE-CMB COMMON MODE CHOKE WE-CMB
Artikelnummer / part number :7448258022
E Testbedingungen / test conditions :
HP 34401 A für/for I N
Luftfeuchtigkeit / humidity:
Umgebungstemperatur / temperature: Prüfspannung / testing voltage N1/N2
WAYNE KERR WK3260B/WK3265 für/for L 0/L N und/and RDC RoHS compliant
LF
This electronic component is designed and developed with the intention for use in general electronics equipments. Before incorporating the components into any equipments in the field such as aerospace, aviation, nuclear control, submarine, transportation, (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network e where higher safety and reliability are especially required or if there is possibility of direct damage or injury to human body. In addition, even electronic component in general electro
equipments, when used in electrical circuits that require high safety, reliability functions or performance, the sufficient reliability evaluation-check for the safety must be performed before use. It is essential to give consideration when to install a protective circuit at the design stage.
SEITE 1 VON 1
/
分销商库存信息: WURTH-ELECTRONICS 7448258022。