Relief Bushings SR1 规格书
SPECIFICATIONS 产品说明书
SPEC19-08 10/15)Outlet: 1-1/4” tube outlet for 1-1/4” slip joint connectionACCESS PANELSHeavy-gauge steel with vandal-resistant screws. Provides access for easy hook-up of all plumbing connections. SUGGESTED SPECIFICATIONSUnit shall include powder-coated finish with vandal-resistant pushbutton actuation, vandal-resistant bubbler with integral hood guard, and contour-formed rounded basin to reduce splash and prevent standing water. Fountain shall comply with ANSI 117:1 and ADA for visual and motion disabilities. The manufacturer shall certify the unit to meet the requirements of NSF/ANSI 61, and the Safe Drinking Water Act.Outdoor TubularModel LK4410FRK is shown.2222 Camden Court Oak Brook, IL In keeping with our policy of continuing product improvement, Elkay reserves the right to change specification without notice. Please visit for the most current version.ModelColor OptionADA CompliantNSF/ANSI 61CertifiedLK4410FRK*(Refer to Finish Color Options)••* Select color option to complete model number. Example: LK4410FRK EVG Beige Black Blue Brown Evergreen GrayOrange Purple Terracotta Red White YellowN o w Av a i l a bl ei n12Co l o r s !Each 4410 FR consists of 2 cartons of the following:• Fountain• Single Freeze-Resistant Valve System - 97243CThis specification describes an Elkay product with design, quality and functional benefits to the user. When making a comparison of other producer’s offerings, be certain these features are not overlooked.FINISH COLOR OPTIONS – Choose color option to complete your model number, add as suffix example: LK4410FRK EVGMatte finish: Evergreen = EVG Gloss finish: Beige = BGE Gray = GRY Terracotta = TER Black = BLK Orange = ORN White = WHT Blue = BLU Purple = PUR Yellow = YLWBrown = BRN Red = REDOPTIONS• Hose Bib (Locking) - LK4471LHB * (Choose color option to complete your model number)• Hose Bib (Non-Locking) - LK4470NLHB* (Choose coloroption to complete your model number)• Direct Bury Kit - 97890CPrinted in the U.S.A.Page 2MODEL LK4410FRK Outdoor TubularFreeze-Resistant FountainOPERATING PRESSURES:Supply water 20 – 105 psi maximumMOUNTING INSTRUCTIONS and PLUMBING INSTRUCTIONSSite and drainage excavation is required for fountain installation. Refer to owner’s manual for site preparation details. Provide solid, well-drained surface to mount pedestal fountain (concrete pad recommended) with adequate support (300 lb. load minimum). (6) 3/8” minimum fasteners (not included) should be attached securely to mounting surface in order to secure fountain, (Refer to rough-in diagram), and be sure to allow an opening for the freeze-resistant valve in the ground as shown in the diagram below). Refer to local codes for any additional requirements.Locate and install plumbing through ground as required. Assemble fountain to prepared site and mounting pad.NOTE: Fountain is not furnished with service valve.Position pedestal over plumbing and secure base to fasteners. Remove access panels and connect supply and water lines. Turn on water supply and check for leaks. Refer to owner’s manual for detailed instructions.Reassemble access panels to pedestal. Trap and service stop not included.2222 Camden Court Oak Brook, IL 。
电源线扣工图片规格介绍和安装使用图
电源线扣工程图片：电源线扣尺寸(Dimensions)Strain Relief Bushings耐扭式加尾档电源线扣线扣安装工程示意图:耐扭式电源线扣尺寸(Dimensions)Flex-Protection Strain Relief Bushings 形状Cross Section Shape型号Model通用UL电线UL WiresAccommodated适用电线尺寸Approx.WireSize(mm)机板孔口径MountingHole机板厚度Max.ThicknessF mm线扣长度LengthD mm包装Packing 物料编码库存A mmB mmPcs/BagPcs/Ctn扁线用Flat SB4F-2PSPT-1SPT-23.0×7.64.1×7.612.70 11.80 0.8-2.7 36.6010010000xksb4f2p SB5F-2P SPT-23.8×7.64.1×7.614.30 13.20 0.8-2.3 36.0010010000xksb5f2p圆线用Round SB7R-3PSJB 3C#18SJT 3C#166.8-8.08.0-9.215.9017.0014.00 0.8-3.2 61.8010010000xksb7r3p直角型、转角电源线扣安装工程示意图:直角型电源线扣尺寸(Dimensions)Right Angle Strain Relief Bushings形状Cross Section Shape型号Model通用UL电线UL WiresAccommodated适用电线尺寸Approx.WireSize(mm)机板孔口径MountingHole机板厚度Max.ThicknessF mm线扣长度LengthD mm包装Packing 物料编码库存A mmB mmPcs/BagPcs/Ctn扁线用Flat SB4F-2LSPT-1SPT-23.0×7.64.1×7.612.70 11.80 1.5-2.6 17.7010010000xksb4f2l圆线用Round SB7R-3L SJT 3C#16 7.6-8.5 15.90 14.00 1.5-3.5 24.5010010000xksb7r3l电源线扣的介绍:电源线扣的材质是尼龙66工程塑料，UL 94V-2阻燃等级，也有用阻燃PP 制造。
超精密金属膜电阻军用标准(RE)规格书
D
50 0 -55 70 175 (°C) (RE)功率 - 温度曲线
型号 额定功率 (W) 最大工作电压(V) 尺寸(Unit: mm) 阻值范围(Ω) 工作溫度范围 标称阻值误差
70 °C L ± 0.3 D ± 0.4 A ± 0.05
RE50 0.125 200 4.0 1.4 0.40
1 ~ 3M
RE55 0.25 200 6.9 2.05 0.60
0.05 ~ 10M
RE60 0.5 250 9.8 3.2 0.60
0.05 ~ 10M
RE65 0.75 300 12.5 3.6 0.60
0.05 ~ 10M
RE70 1.0 350 14.1 4.65 0.80
0.05 ~ 10M
RE75 1.5 500 17.8 7.2 0.80
长期
无机械损伤，飞弧，绝缘击穿 短期
GJB244A (MIL-PRF-55182) 3.17/3.22/3.23 ΔR≤±(0.20%R+0.01Ω)
无机械损伤
GJB244A (MIL-PRF-55182)3.20 ΔR≤±(0.10%R+0.01Ω)
无机械损伤
Version 2014
德键电子工业股份有限公司
要求
GJB244A (MIL-PRF-55182) 3.24 ΔR≤±(0.5%R+0.01Ω) ΔR≤±(2%R+0.01Ω) GJB244A (MIL-PRF-55182)3.21 ΔR≤±(0.4%R+0.01Ω) GJB244A (MIL-PRF-55182)3.25 ΔR≤±(2.0%R+0.01Ω) GJB244A (MIL-PRF-55182) 3.18/3.29/3.16 ΔR≤±(0.15%R+0.01Ω)
Spears制造业公司产品简介和基本配件说明书
Modulating Actuator Voltage 115 VAC 230 VAC 24 VAC 24 VDC
Input Signal
4-20mA, 0 - 5 VDC, 0 - 10 VDC 4-20mA, 0 - 5 VDC, 0 - 10 VDC 4-20mA, 0 - 5 VDC, 0 - 10 VDC 4-20mA, 0 - 5 VDC, 0 - 10 VDC
LED Position Indicator Lights
LED (light emitting diode) red/green indicator lights mounted on actuator enclosure to designate open/closed position.
ห้องสมุดไป่ตู้
Positioner Board (Modulating)
Heater and Thermostat
Mounted internally, heats the inside of the enclosure in low temperature environments to prevent condensation and keep internal lubricants fluid. The thermostat activates the heater when the enclosure internal temperature drops below the set point. There are a variety of thermostats available and a set point must be specified at the time of ordering.
Resistor.Today-PZFR系列精密箔电阻规格书
PZFR精密箔技术贴片电阻高精密表贴电阻，金属箔技术，最高工作温度+175°C温飘±2ppm/°C ，最高精度±0.01%，高耐湿能力，天然低噪声抗脉冲能力强，抗静电，极好货架寿命及负载寿命高精密和高稳定性应该一起来讨论才具有实际的意义。
无论是膜式的电阻还是合金的电阻，通过精密的调阻工艺都可以达到很高的初始精度。
但电阻在使用前要经过运输，存储，焊接等过程，这些过程都会造成电阻阻值的变化。
另外电阻需要在不同的环境温度下工作，同时加载功率也会使电阻产生自热，这些因素都会使阻值发生不可逆的变化。
高精密的电阻必须同时具有高稳定性的特点。
电阻的稳定性比初始精度更重要最快24小时交货，无最小起定量限制开步电子常备箔电阻芯片，可以满足小批量快速交付。
从用户下单到发货最快24小时完成，1且不设最小订购量，即使1片也可以订购。
每只箔电阻出厂前都经过严格的测试程序，确保符合性能指标。
不受阻值标准约束，可任意定义需要的阻值每只箔电阻都要经过调阻，通过切断边缘区域的调阻带从而增加阻值，达到调整阻值的目的。
和其他电阻不同，用户可以任意的定义阻值，不受标准阻值的约束，比如1.234欧。
备箔芯片库存可以在关注“开步电子微服平台”，进入箔电阻库存查询。
常① 根据不同的使用温度范围，我们可以定制最低+/-1ppm 的温飘。
PZFR精密箔技术贴片电阻额定功率%环境温度°C1007550250-55°C +70°C-75-50-250+25+50+75+100+125+150+175在需要选择一个具有长期稳定性的电阻的时候，几个因素需要被考虑。
这些因素包括：温度系数（TCR ）, 功率系数（PCR ）, 负载寿命，寿命末期精度，噪声，热电势，抗静电能力。
PZFR 系列箔电阻基于全新的Z1箔技术生产，Z1箔技术在原有Z 箔技术的基础上改进了绑定层和保护层，极大的改善了电阻的稳定性和耐湿能力，使得该电阻可以在很宽的温度范围内工作。
Littelfuse ULTRAMOV Datasheet力特压敏电阻规格书
Features
• Lead–free, Halogen-Free • Custom voltage
and RoHS compliant
types available
• High peak surge
• Standard lead form and
ctour1r0eknAt ,rastiinnggle(IT8M)xup 20 pulse, (20mm)
91788 BSIIE1C4Q.0-0C011
J 503242422
Notes: . Epoxy coated only. 2. Phenolic coated only. 3. All epoxy coated sizes are UL Recognized while only 10mm, 14mm, and 20mm phenolic
UltraMOV® Series Ratings & Specifications
Epoxy Coated Models
Phenolic Coated Models
Part Number
Branding
Part Number
Branding
V07E130P P7V130 V07P130P P7P130 V10E130P P10V130 V10P130P P10P130 V14E130P P14V130 V14P130P P14P130 V20E130P P20V130 V20P130P P20P130 V07E140P P7V140 V07P140P P7P140 V10E140P P10V140 V10P140P P10P140 V14E140P P14V140 V14P140P P14P140 V20E140P P20V140 V20P140P P20P140 V07E150P P7V150 V07P150P P7P150 V10E150P P10V150 V10P150P P10P150 V14E150P P14V150 V14P150P P14P150 V20E150P P20V150 V20P150P P20P150 V07E175P P7V175 V07P175P P7P175 V10E175P P10V175 V10P175P P10P175 V14E175P P14V175 V14P175P P14P175 V20E175P P20V175 V20P175P P20P175 V07E230P P7V230 V07P230P P7P230 V10E230P P10V230 V10P230P P10P230 V14E230P P14V230 V14P230P P14P230 V20E230P P20V230 V20P230P P20P230 V07E250P P7V250 V07P250P P7P250 V10E250P P10V250 V10P250P P10P250 V14E250P P14V250 V14P250P P14P250 V20E250P P20V250 V20P250P P20P250 V07E275P P7V275 V07P275P P7P275 V10E275P P10V275 V10P275P P10P275 V14E275P P14V275 V14P275P P14P275 V20E275P P20V275 V20P275P P20P275 V07E300P P7V300 V07P300P P7P300 V10E300P P10V300 V10P300P P10P300 V14E300P P14V300 V14P300P P14P300 V20E300P P20V300 V20P300P P20P300 V07E320P P7V320 V07P320P P7P320 V10E320P P10V320 V10P320P P10P320 V14E320P P14V320 V14P320P P14P320 V20E320P P20V320 V20P320P P20P320 V07E385P P7V385 V07P385P P7P385 V10E385P P10V385 V10P385P P10P385 V14E385P P14V385 V14P385P P14P385 V20E385P P20V385 V20P385P P20P385 V07E420P P7V420 V07P420P P7P420 V10E420P P10V420 V10P420P P10P420 V14E420P P14V420 V14P420P P14P420 V20E420P P20V420 V20P420P P20P420 V07E440P P7V440 V07P440P P7P440 V10E440P P10V440 V10P440P P10P440 V14E440P P14V440 V14P440P P14P440 V20E440P P20V440 V20P440P P20P440 V07E460P P7V460 V07P460P P7P460 V10E460P P10V460 V10P460P P10P460
APT60DQ120SG商品说明书
APT60DQ120SGDatasheet Ultrafast Soft Recovery Rectifier DiodeFinalApril 2018Contents1Revision History (1)1.1Revision A (1)2Product Overview (2)2.1Benefits (2)2.2Applications (2)3Electrical Specifications (3)3.1Absolute Maximum Ratings (3)3.2Electrical Performance (3)3.3Dynamic Characteristics (4)3.4Typical Performance Curves (4)3.5Reverse Recovery Overview (6)4Package Specification (7)4.1Package Outline Drawing (7)1Revision HistoryThe revision history describes the changes that were implemented in the document. The changes arelisted by revision, starting with the most current publication.1.1Revision ARevision A was published in April 2018. It is the first publication of this document.2Product OverviewFeaturesThe following are key features of the APT60DQ120SG device:Ultrafast recovery timesSoft recovery characteristicsLow forward voltageLow leakage currentAvalanche energy ratedRoHS compliant2.1BenefitsThe following are benefits of the APT60DQ120SG device:Higher switching frequencyLow switching lossesLow noise (EMI) switchingHigher reliability systemsIncreased system power density2.2ApplicationsThe APT60DQ120SG device is designed for the following applications: Power Factor Correction (PFC)Anti-parallel diodeSwitch-mode power supplyInverters/convertersMotor controllersFreewheeling diodeSwitch-mode power supplyInverters/convertersSnubber/clamp diode3Electrical SpecificationsThis section shows the electrical specifications for the APT60DQ120SG device.3.1Absolute Maximum RatingsThe following table shows the absolute maximum ratings for the APT60DQ120SG device.All ratings: T = 25 °C unless otherwise specified.CTable 1 • Absolute Maximum RatingsSymbol Parameter Ratings UnitV R Maximum DC reverse voltage1200VV RRM Maximum peak repetitive reverse voltage1200V RWM Maximum working peak reverse voltage1200I F(AV)Maximum average forward current (T = 103 °C, duty cycle = 0.5)C60AI F(RMS)RMS forward current87I FSM Non-repetitive forward surge current (T = 45 °C, 8.3 ms)J540E AVL Avalanche energy (1 A, 40 mH)20mJT , TJ STG Operating and storage temperature range–55 to 175°CT L Lead temperature for 10 seconds300The following table shows the thermal and mechanical characteristics of the APT60DQ120SG device.Table 2 • Thermal and Mechanical CharacteristicsSymbol Characteristic Min Typ Max UnitRθJC Junction-to-case thermal resistance0.40°C/WW T Package weight0.14oz4.0g 3.2Electrical PerformanceThe following table shows the static characteristics of the APT60DQ120SG device.Table 3 • Static CharacteristicsSymbol Characteristic Test Conditions Min Typ Max UnitV F Forward Voltage I = 60 AF 2.8 3.3VI = 120 AF 3.35I = 60 A, T = 125 °CF J 2.11I RM Maximum reverse leakage current V = 1200 VR100μAV = 1200 V, T = 125 °CR J500C J Junction capacitance V = 200 VR37pF3.3Dynamic CharacteristicsThe following table shows the dynamic characteristics of the APT60DQ120SG device.Table 4 • Dynamic CharacteristicsSymbol Characteristic Test ConditionsMin Typ Max Unit t rrReverse recovery timeI = 1 A, di /dt = –100 A/µs F F V = 30 V R T = 25 °CJ30nst rr Reverse recovery time I = 60 A, di /dt = –200 A/µs F F V = 800 V R T = 25 °CC 320 Q rr Reverse recovery change 630 nC I RRM Maximum reverse recovery current 5 A t rr Reverse recovery time I = 60 A, di /dt = –200 A/µs F F V = 800 V R T = 125 °CC 420 ns Q rr Reverse recovery charge 2810 nC I RRM Maximum reverse recovery current 12 A t rr Reverse recovery time I = 60 A, di /dt = –1000 A/µs F F V = 800 V R T = 125 °CC 190 ns Q rr Reverse recovery change 4415 nC I RRMMaximum reverse recovery current38A3.4Typical Performance CurvesThis section shows the typical performance curves for the APT60DQ120SG device.Figure 1 • Maximum Transient Thermal ImpedanceFigure 2 • Forward Current vs. Forward Voltage Figure 3 • trr vs. Current Rate of ChangeFigure 2 • Forward Current vs. Forward Voltage Figure 3 • trr vs. Current Rate of ChangeFigure 4 • Qrr vs. Current Rate of Change Figure 5 • IRRM vs. Current Rate of ChangeFigure 6 • Dynamic Parameters vs. Junction TemperatureFigure 7 • Maximum Average Forward Current vs. Case TemperatureFigure 8 • Junction Capacitance vs. Reverse Voltage1. 2. 3. 4. 5.Figure 8 • Junction Capacitance vs. Reverse Voltage3.5Reverse Recovery OverviewThe following illustration shows the reverse recovery testing and measurement information for the APT60DQ120SG device.Figure 9 • Diode Reverse Recovery Waveform and DefinitionsI —Forward conduction current.F di /dt—Rate of diode current change through zero crossing.F I —Maximum reverse recovery current.RRM t —Reverse recovery time, measured from zero crossing where diode current goes from positive to rr negative, to the point at which the straight line through I and 0.25 × I passes through zero.RRM RRM Q —Area under the curve defined by I and t .rr RRM rr4Package SpecificationThis section outlines the package specification for the APT60DQ120SG device.4.1Package Outline DrawingThis section details the D PAK package drawing of the APT60DQ120SG device. Dimensions are in3millimeters and (inches).Figure 10 • Package Outline DrawingMicrosemi Corporate HeadquartersOne Enterprise, Aliso Viejo,CA 92656 USAWithin the USA: +1 (800) 713-4113Outside the USA: +1 (949) 380-6100Fax: +1 (949) 215-4996Email:***************************© 2018 Microsemi Corporation. All rights reserved. Microsemi and the Microsemi logo are trademarks of Microsemi Corporation. All other trademarks and service marks are the property of their respective owners.Microsemi makes no warranty, representation, or guarantee regarding the information contained herein or the suitability of its products and services for any particular purpose, nor does Microsemi assume any liability whatsoever arising out of the application or use of any product or circuit. The products sold hereunder and any other products sold by Microsemi have been subject to limited testing and should not be used in conjunction with mission-critical equipment or applications. Any performance specifications are believed to be reliable but are not verified, and Buyer must conduct and complete all performance and other testing of the products, alone and together with, or installed in, any end-products. Buyer shall not rely on any data and performance specifications or parameters provided by Microsemi. It is the Buyer's responsibility to independently determine suitability of any products and to test and verify the same. The information provided by Microsemi hereunder is provided "as is, where is" and with all faults, and the entire risk associated with such information is entirely with the Buyer. Microsemi does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other IP rights, whether with regard to such information itself or anything described by such information. Information provided in this document is proprietary to Microsemi, and Microsemi reserves the right to make any changes to the information in this document or to any products and services at any time without notice.Microsemi Corporation (Nasdaq: MSCC) offers a comprehensive portfolio of semiconductor and system solutions for aerospace & defense, communications, data center and industrial markets. Products include high-performance and radiation-hardened analog mixed-signal integrated circuits, FPGAs, SoCs and ASICs; power management products; timing and synchronization devices and precise time solutions, setting the world's standard for time; voice processing devices; RF solutions; discrete components; enterprise storage and communication solutions; security technologies and scalable anti-tamper products; Ethernet solutions; Power-over-Ethernet ICs and midspans; as well as custom design capabilities and services. Microsemi is headquartered in Aliso Viejo, California, and has approximately 4,800 employees globally. Learn more at .053-4250。
瑞丰WI-E-045A1型号电子产品规格书说明书
information on the applications如产品需要用在有特殊质量要求及可靠性要求的地LEDs without having consentinform Refond in writinganalysis.在取得瑞丰的同意前，客户不应该对产品进行拆解分析，如发现失效产品，请直RF-W3S198TS-A12Features 特征Extremely wide viewing angle.发光角度大Suitable for all SMT assembly and solder process.适用于所有的SMT组装和焊接工艺 Moisture sensitivity level:Level3.防潮等级Level3Package:4000pcs/reel.包装每卷4000pcsRoHS compliant.满足RoHS要求Description描述The Colour LED which was fabricated using blue,green and orange chip 该产品为三色光LED，是由蓝光、绿光和橙光晶片封装形成Applications应用Optical indicator.光学指示Switch and Symbol,Display.开关和标识、显示器等General use.其他应用Package Dimension 外观尺寸NOTES:1.All dimensions units are millimeters.(所有尺寸标注单位为毫米)2.All dimensions tolerances are±0.2mm unless otherwise noted.(除特别标注外，所有尺寸公差为±0.2毫米)----Note:备注Vr=5V For test conditions.Vr=5v为测试分选条件。
Absolute Maximum Ratings at Ts=25°C 绝对最大值1.2.3.4.5.6.Typical optical characteristics curves典型光学特性曲线Packaging Specifications⏹Carrier Tape Dimensions载带尺寸Note:Thetolerances unless mentioned ±0.1mm.Unit :mm 注：未注公差为±0.1毫米，尺寸单位：毫米。
铁姆肯公司供应商要求手册第九版说明书
供应商要求手册第九版铁姆肯公司标准 29.1目录前言/简介 (1)标准要求–质量 (2)1.0 供应商最低要求 (4)1.1 简介 (4)1.2 供应商质量系统要求 (4)1.3 产品检验 (4)1.4 不合格（偏离）产品 (5)1.5 设计和过程变更的管理 (6)1.6 采购产品的提交和批准过程 (7)1.7 测量系统分析 (7)1.8 样品提交要求 (7)1.9 文件、证书和数据要求 (8)1.10 有害材料 - 化学品安全说明书 (8)1.11 发运和包装要求 (8)1.12 供应链要求 (8)1.13 供应商材料的追溯性 (9)1.14 材料质保书数据库 (9)1.15 控制项目 ( ) 部件和特殊项目或过程..... .. (9)1.16 记录 (10)1.17 供应商评估和过程 (10)1.18 供应商升级过程 (11)1.19 供应商控制发运 (11)1.20 供应商安全投产 (11)2.0 供应商发展和推荐的最佳实践 (11)2.1 前期产品质量策划和预防 (12)2.2 目标设定和问题解决 (12)2.3 成本削减方针 (13)2.4 费用索赔过程 (13)2.5 防错 (13)2.6 统计技术 (13)2.7 持续改善过程 (14)2.8 环境、健康和安全 (14)3.0 供应商质量保证航空规定 (15)3.1 抽样计划要求 (15)3.2 接受权威媒体 (15)3.3 检验和测试报告 (15)3.4 出货产品合格证 (15)3.5 首件检验 (15)3.6 可追溯性 (15)3.7 文件保留 (16)3.8 变更批准 (16)3.9 材料批准委员会授权 (16)3.10 政府财产 (16)3.11 访问权限 (16)3.12 符合 DFARS 美国国防联邦采购条例增补条例（252.225-7014 优先采购美国国产特种金属）要求的一致性Alternate I (16)3.13 DFARS 252.225-7016对钢球和滚子的限制 (18)3.14 NADCAP 对特殊过程的要求 (19)3.15 外物损坏 (19)术语[黑体字] (19)前言/简介供应商应对其产品及服务的质量负责。
FOXBORO I A Series HARDWARE产品规格说明书
FOXBORO ®The FBM214 HART ® Communication Input Interface Module provides eight input channels, each accepting a 4 to 20mA analog signal or a digital HART signal superimposed on a 4 to 20 mA analog input signal.FEATURESKey features of the FBM214 module are:Eight analog input channels, each accepting oneof the following inputs:•Standard 4 to 20 mA analog sensor signal •Digital HART Frequency Shift Keying (FSK) signal superimposed on a 4 to 20 mA analog input signal.FSK modem dedicated to each input channel forbi-directional digital communications with a HART field deviceAnalog to digital conversion of each of the 4to20mA input signals from the HART devicesSupport for the HART universal commandsnecessary to interface the field device with the I/A Series ® system databaseGalvanic isolation of the group of 8 inputchannels from ground and module logicCompact, rugged design suitable for enclosure inClass G3 (harsh) environmentsHigh accuracy achieved by sigma-delta dataconversions for each channelTermination Assemblies (TAs) for locally orremotely connecting field wiring to the FBM214Termination Assemblies for per channel internallyand/or externally loop powered transmitters.PSS 21H-2Z14 B4 Page 2OVERVIEWThe FBM214 HART Communication Input Interface Module contains eight 4to20mA group isolated analog input channels. The FBM214 supports any mix of standard 4to20mA devices and HART devices.The FBM214 serves as a HART communications field device host, enabling the I/A Series system to request and receive two digital messages per second from the field device. The message pass-through capability can be used to support HART universal, common practice, and device-specific commands, but not the burst communication mode. These commands are implemented using the Intelligent Field Device Configurator (IFDC — refer toPSS 21S-8A3 B3 for details).The FBM214 provides a common isolated power supply to power all eight channels. Optionally, the channels can be powered by an external power supply. However, when a common external power supply is used with two or more channels, a Cable Balun module is required to prevent channel cross talk.COMPACT DESIGNThe FBM214 has a compact design, with a rugged extruded aluminum exterior for physical protection of the circuits. Enclosures specially designed for mounting the FBMs provide various levels of environmental protection, up to harsh environments per ISA Standard S71.04.HIGH ACCURACYFor high accuracy, the module incorporates a Sigma-Delta converter which can provide new analog input values for each channel every 100 milliseconds.VISUAL INDICATORSLight-emitting diodes (LEDs) incorporated into the front of the module provide visual indication of the module’s operational status, and communication activity on the channels.EASY REMOVAL/REPLACEMENTThe module can be removed/replaced without removing field device termination cabling, power, or communications cabling.FIELDBUS COMMUNICATIONA Fieldbus Communication Module or a Control Processor interfaces the redundant 2 Mbps module Fieldbus used by the FBMs. The FBM214 module accepts communication from either path (A or B) of the redundant 2 Mbps fieldbus – should one path fail or be switched at the system level, the module continues communication over the active path.The use of an external power supply common to two or more loops requires a Cable Balun Module to maintain communication signal line balance.MODULAR BASEPLATE MOUNTINGThe module mounts on a modular baseplate which accommodates up to four or eight FBMs. The modular baseplate is either DIN rail mounted or rack mounted, and includes signal connectors for redundant fieldbus, redundant independent dc power, and termination cables.TERMINATION ASSEMBLIESField input signals connect to the FBM subsystem via DIN rail mounted TAs. The TAs used with theFBM214 are described in “TERMINATION ASSEMBLIES AND CABLES” on page8.PSS 21H-2Z14 B4Page 3CABLE BALUN MODULEThe Cable Balun module is used to maintain digital communication line balance for HART Transmitter to FBM loops that are powered from a common external power supply. This powering effectively connects one line of each loop together. Without the Baluns, in each loop so powered, the common connection at the external power supply, would cause near end crosstalk at the system end of the loop wiring cable. Loops using FBM internal power source do not require Baluns.The Cable Balun module contains multiple Baluns. One Balun segment is interconnected in each loop powered from an external power supply per the diagram above. There is one Cable Balun module.Figure 1. Cable Balun Module Cable Balun ModuleModule Model ModulePart No.No. of Balunsin the ModuleCBM-4P0903SV4PSS 21H-2Z14 B4Page 4FUNCTIONAL SPECIFICATIONSField Device ChannelsVERSION SUPPORTEDHART Protocol v6INTERFACE8 group-isolated channelsCOMMUNICATION TO THE DEVICEPoint-to-point, master/slave, asynchronous, half-duplex, at 1200 baud.ERROR CHECKINGParity on each byte, and one CRC check byte.SPEED2 messages per secondFASTEST ALLOWED ECB BLOCK PERIOD500 msecMAXIMUM DISTANCE (FBM214 TO FIELDDEVICE)Meets HART FSK physical layer specificationHCF_SPEC-54, Revision 8.1 [up to 3030 m(10000ft)](1).COMPLIANCE VOLTAGE18 V dc minimum at 20.5 mACURRENT INPUTSSense Resistor61.9 Ω nominalTotal Input Resistance280 Ω minimumAccuracy (Includes Nonlinearity)±0.03% of full scaleTemperature Coefficient50 ppm/ºCResolution15 bitsUpdate Rate100 msIntegration Time500 msCommon Mode Rejection>100 db at 50 or 60 HzNormal Mode Rejection>35 db at 50 or 60 HzMAXIMUM LOOP RESISTANCE280 Ω (not including the field device)(2)LOOP POWER SUPPLY PROTECTIONEach channel is galvanically group isolated,current limited and voltage regulated. All inputsare limited by their design to less than 30 mA. Ifthe current limit circuit shorts out, the current islimited to about 85 mA.FBM INPUT IMPEDANCE280 Ω minimumFBM INTERNAL POWER FOR FIELD DEVICE24 V dc ±10% common power supply for allchannels. Loop load limited to one device perchannel.ISOLATIONThe channels are not galvanically isolated fromeach other, but are galvanically isolated (bothoptical and transformer isolation) as a group from ground and module logic. Inputs use an internal FBM isolated power supply for field power. Themodule withstands, without damage, a potential of 600 V ac applied for one minute between the group-isolated channels and earth (ground).CAUTIONThis does not imply that these channels areintended for permanent connection tovoltages of these levels. Exceeding the limitsfor input voltages, as stated elsewhere in thisspecification, violates electrical safety codesand may expose users to electric shock. Fieldbus CommunicationCommunicates with its associated FCM or FCP via the redundant 2 Mbps module FieldbusHEAT DISSIPATION4 W (maximum)(1)The maximum allowable distance decreases when the loop is operated through an intrinsic safety barrier. The maximum distance ofthe field device from the FBM is a function of compliance voltage, wire gauge and voltage drop at the device.(2)In an intrinsic safety application, if a zener barrier is used between the FBM and the field device, the power supply must be set at24V dc +5%, -1%. There are no specific constraints with the use of galvanic barriers.PSS 21H-2Z14 B4Page 5 FUNCTIONAL SPECIFICATIONS (CONTINUED)Power RequirementsINPUT VOLTAGE RANGE (REDUNDANT)24V dc ±5%CONSUMPTION7 W (maximum)Regulatory ComplianceELECTROMAGNETIC COMPATIBILITY (EMC) European EMC Directive 89/336/EECMeets:EN 50081-2 Emission standardEN 50082-2 Immunity standardEN 61326 Annex A (Industrial Levels) CISPR 11, Industrial Scientific and Medical(ISM) Radio-frequency Equipment -Electromagnetic Disturbance Characteristics- Limits and Methods of MeasurementMeets Class A LimitsIEC 61000-4-2 ESD ImmunityContact 4 kV, air 8 kVIEC 61000-4-3 Radiated Field Immunity10 V/m at 80 to 1000 MHzIEC 61000-4-4 Electrical FastTransient/Burst Immunity2 kV on I/O, dc power and communicationlinesIEC 61000-4-5 Surge Immunity2kV on ac and dc power lines; 1kV on I/Oand communications linesIEC 61000-4-6 Immunity to ConductedDisturbances Induced by Radio frequencyFields10 V (rms) at 150 kHz to 80 MHz on I/O,dc power and communication linesIEC 61000-4-8 Power Frequency MagneticField Immunity30 A/m at 50 and 60 HzPRODUCT SAFETY (FBM AND CABLE BALUN) Underwriters Laboratories (UL) for U.S. andCanadaUL/UL-C listed as suitable for use inUL/UL-C listed Class I, Groups A-D;Division 2; temperature code T4 enclosurebased systems. These modules are also ULand UL-C listed as associated apparatus forsupplying non-incendive communicationcircuits for Class I, Groups A-D hazardouslocations when connected to specifiedI/A Series® processor modules as describedin the I/A Series DIN Rail MountedSubsystem User’s Guide (B0400FA). Wherepower is supplied by the FBM,communications circuits also meet therequirements for Class2 as defined inArticle725 of the National Electrical Code(NFPA No.70) and Section 16 of theCanadian Electrical Code (CSA C22.1).Conditions for use are as specified in theI/A Series DIN Rail Mounted SubsystemUser’s Guide (B0400FA).European Low Voltage Directive 73/23/EECand Explosive Atmospheres (ATEX) directive94/9/ECCENELEC (DEMKO) certified as EEx nA IICT4 for use in CENELEC certified Zone 2enclosure certified as associated apparatusfor supplying non-incendive field circuits forZone 2, Group IIC, potentially explosiveatmospheres when connected to specifiedI/A Series processor modules as describedin the I/A Series DIN Rail MountedSubsystem User’s Guide (B0400FA). Also,see Table1 on page9.Calibration RequirementsCalibration of the module or termination assembly is not required.PSS 21H-2Z14 B4Page 6ENVIRONMENTAL SPECIFICATIONS(3)OperatingTEMPERATUREModule-20 to +70°C (-4 to +158°F)Termination AssemblyPVC-20 to +50°C (-4 to +122°F)PA-20 to +70°C (-4 to +158°F) RELATIVE HUMIDITY5 to 95% (noncondensing)ALTITUDE-300 to +3,000m (-1,000 to +10,000ft)StorageTEMPERATURE-40 to +70°C (-40 to +158°F)RELATIVE HUMIDITY5 to 95% (noncondensing)ALTITUDE-300 to +12,000m (-1,000 to +40,000ft) ContaminationSuitable for use in Class G3 (Harsh) environments as defined in ISA Standard S71.04, based on exposure testing according to EIA Standard 364-65, Class III. Vibration7.5 m/S2 (0.75 g) from 5 to 500 Hz(3)The environmental limits of this module may be enhanced by the type of enclosure containing the module. Refer to the applicableProduct Specification Sheet (PSS) which describes the specific type of enclosure that is to be used.PSS 21H-2Z14 B4Page 7 PHYSICAL SPECIFICATIONSMountingMODULEFBM214 mounts on a modular baseplate. Thebaseplate can be mounted on a DIN rail(horizontally or vertically), or horizontally on a19-inch rack using a mounting kit. Refer toPSS21H-2W6B4 for details.TERMINATION ASSEMBLYThe TA mounts on a DIN rail and accommodates multiple DIN rail styles including 32mm (1.26in) and 35mm 1.38in).MassMODULE284 g (10 oz) approximateTERMINATION ASSEMBLYCompression181 g (0.40 lb) approximateRing Lug249 g (0.55 lb) approximateDimensions – ModuleHEIGHT102 mm (4 in)114 mm (4.5 in) including mounting lugsWIDTH45 mm (1.75 in)DEPTH104 mm (4.11 in)Dimensions – Termination AssemblySee page10.Part NumbersFBM214 MODULEP0922VTTERMINATION ASSEMBLIESSee “FUNCTIONAL SPECIFICATIONS –TERMINATION ASSEMBLIES” on page8. Termination CablesCABLE LENGTHSUp to 30 m (98 ft)CABLE MATERIALSPolyurethane or Hypalon®/XLPTERMINATION CABLE TYPEType 1 – See Table2 on page9.CABLE CONNECTION – TA25-pin male D-subminiatureConstruction – Termination AssemblyMATERIALPolyvinyl Chloride (PVC), compressionPolyamide (PA), compressionPVC, ring lugFAMILY GROUP COLORGreen – communicationTERMINAL BLOCKS3 tiers, 8 positionsField Termination ConnectionsCOMPRESSION-TYPE ACCEPTED WIRINGSIZESSolid/Stranded/AWG0.2 to 4 mm2/0.2 to 2.5 mm2/24 to 12 AWGStranded with Ferrules0.2 to 2.5 mm2 with or without plastic collarRING-LUG TYPE ACCEPTED WIRING SIZES#6 size connectors (0.375 in (9.5 mm))0.5 to 4 mm2/22 AWG to 12 AWGPSS 21H-2Z14 B4Page 8TERMINATION ASSEMBLIES AND CABLESField input signals connect to the FBM subsystem via DIN rail mounted Termination Assemblies, which are electrically passive.TAs for the FBM214 are available in the following forms: Compression screw type using Polyvinyl Chloride(PVC) materialCompression screw type using Polyamide (PA) material Ring lug type using PVC material.See the following “FUNCTIONAL SPECIFICATIONS –TERMINATION ASSEMBLIES” for a list of TAs used with the FBM214.The FBM214 provides sufficient loop resistance to allow use of the HART Hand-Held Terminal, or PC20 Intelligent Field Device Configurator (PSS 2A-1Z3 E).A removable termination cable connects the DIN railmounted TA to the FBM via a field connector on the baseplate in which the FBM is installed. Termination cables are available in the following materials: PolyurethaneHypalon XLP .Termination cables are available in a variety of lengths, up to 30 meters (98feet), allowing the Termination Assembly to be mounted in either theenclosure or in an adjacent enclosure. See Table 2 for a list of termination cables used with the TAs forthe FBM214.FUNCTIONAL SPECIFICATIONS – TERMINATION ASSEMBLIESFBM Type Input SignalTA Part NumberTermination TA Cable TACertification PVC (a)(a)PVC is polyvinyl chloride rated from -20 to +50°C (-4 to +122°F).PA is Polyamide rated from -20 to +70°C (-4 to +158°F).PA (a)Type (b)(b) C = TA with compression terminals; RL = TA with ring lug terminals.Type (c)(c)See Table 2 for cable part numbers and specifications.Type (d)(d)See Table 1 for Termination Assembly certification definitions.FBM2148 input channels, 4 to 20mA analog signal, alone or with HART signal superimposedP0916BX P0926EA P0926TD CRL11, 2PSS 21H-2Z14 B4Page 9Table 1. Certification for Termination AssembliesType Certification (a)(a)All TAs are UL/UL-C listed to comply with applicable ordinary location safety standards for fire and shock hazards. Hazardous locationtypes comply with ATEX directive for II 3 G use. They also comply with the requirements of the European Low Voltage Directive. All listings/certifications require installation and use within the constraints specified in DIN Rail Mounted Subsystem User’s Guide (B0400FA) and the conditions stated in UL and DEMKO reports.Type 1TAs are UL/UL-C listed as suitable for use in Class I; Groups A-D; Division 2 temperature code T4 hazardous locations. They are CENELEC (DEMKO) certified EEx nA IIC T4 for use in Zone 2 potentially explosive atmospheres.Type 2TAs are UL/UL-C listed as associated apparatus for supplying non-incendive field circuits Class I; Groups A-D; Division 2 hazardous locations when connected to specified DIN rail mounted FBMs and field circuits meeting entity parameter constraints specified in DIN Rail Mounted Subsystem User’s Guide (B0400FA). They are also CENELEC (DEMKO) certified as associated apparatus for supplying field circuits for Group IIC, Zone 2 potentially explosive atmospheres. Field circuits are also Class 2 limited energy (60 V dc, 30 V ac, 100 VA or less) if customer-supplied equipment meets Class 2 limits.Table 2. Cables Types and Part NumbersCable Lengthm (ft) Type 1P/PVC (a)Type 1H/XLPE (b)Cable Lengthm (ft) Type 1P/PVC (a)Type 1H/XLPE (b)0.5 (1.6)P0916DA P0916VA 10.0 (32.8) P0916DE P0916VE 1.0 (3.2) P0916DB P0916VB 15.0 (49.2) P0916DF P0916VF 2.0 (6.6)P0931RM P0931RR 20.0 (65.6) P0916DG P0916VG 3.0 (9.8) P0916DC P0916VC 25.0 (82.0) P0916DH P0916VH 5.0 (16.4)P0916DDP0916VD30.0 (98.4)P0916DJP0916VJ(a)P/PVC is polyurethane outer jacket and semi-rigid PVC primary conductor insulation.(b)H/XLPE is Hypalon outer jacket and XLPE (cross-linked polyethylene) primary conductor insulation.PSS 21H-2Z14 B4Page 10DIMENSIONS – NOMINALRELATED PRODUCT SPECIFICATION SHEETSCompression Termination AssemblyRing Lug Termination Assembly(a) Overall width – for determining DIN rail loading.(b) Height above DIN rail (add to DIN rail height for total).PSS NumberDescriptionPSS 21H-2W1 B3DIN Rail Mounted FBM Subsystem OverviewPSS 21H-2W2 B3DIN Rail Mounted FBM Equipment, Agency CertificationsPSS 21H-2Z14 B4Page 11PSS 21H-2Z14 B4 Page 12IPS Corporate Headquarters 5601 Granite Parkway Suite 1000 Plano, TX 75024United States of AmericaFoxboro Global Client Support Inside U.S.: 1-866-746-6477 Outside U.S.: 1-508-549-2424 or contact your local Foxboro representative.Facsimile: 1-508-549-4999Invensys, Foxboro, I/A Series and the IPS Logo are trademarks of Invensys plc, its subsidiaries, and affiliates. All other brand names may be trademarks of their respective owners.Copyright 2002-2010 Invensys Systems, Inc.All rights reservedMB 21A Printed in U.S.A. 0210。
贴片电感DFE201610E-1R0M 品牌TOKO规格书推荐
DFE201610EInductance Range: 0.24~10μH(Unit: mm)(Unit: mm)∙ Miniature size: 2016 footprint (2.0mm×1.6mm) and low profile(1.0mm Max. height)∙ The use of magnetic iron powder ensure capability for large current.∙ The use of Flat wire for Low DC resistance. ∙ Magnetically shielded, low audible core noise. ∙ Reflow solderable.∙ Operating temperature : -40～+125°C ∙ 小型薄型構造 (2.0ｘ1.6ｍｍ角、高さ1.0mm Max.) ∙ 磁性材に鉄系磁性粉を用いた大電流対応 ∙ 平角線採用による低直流抵抗 ∙ 閉磁路構造、低コア鳴きノイズ ∙ リフロはんだ対応∙動作温度範囲：-40～+125°C(1) Inductance is measured with a LCR meter 4284A (Agilent Technologies ) or equivalent. Test frequency at 1MHz(2) DC resistance is measured with 34420A (Agilent Technologies) or 3541(HIOKI). (Reference ambient temperature 20°C)(3) Inductance Decrease Current based upon 30% inductance reduction from the initial value(4) Temperature Rise Current based upon 40°C temperature rise. (Reference ambient temperature 20°C)(1) インダクタンスはLCR メータ4284A (Agilent Technologies ) または同等品により測定する。
5441FE安全与声音产品说明书
Product Description Security & Sound Cable, Riser-CMR, 2-20 AWG stranded bare copper pairs with polypropylene insulation, Beldfoil® shield and PVC jacket with ripcord
Yes
Overall Cable Diameter (Nominal):
0.218 in
Electrical Characteristics
Electricals
Nom. Conductor DCR
10.3 Ohm/1000ft
Nom. Capacitance Cond-to-Cond Nom. Capacitance Cond-to-Other (Conds + Shield)
Color Code
Pair(s) PP - Polypropylene 0.008 in (0.20 mm) 0.052 in (1.3 mm)
Black & Red, Black & White
Outer Shield
Shield Type
Material
Coverage Drainwire Type
All sales of Belden products are subject to Belden's standard terms and conditions of sale.
Belden believes this product to be in compliance with all applicable environmental programs as listed in the data sheet. The information provided is correct to the best of Belden's knowledge, information and belief at the date of its publication. This information is designed only as a general guide for the safe handling, storage, and any other operation of the product itself or the one that it becomes a part of. The Product Disclosure is not to be considered a warranty or quality specification. Regulatory information is for guidance purposes only. Product users are responsible for determining the applicability of legislation and regulations based on their individual usage of the product.
1SR156-400TE25;中文规格书,Datasheet资料
Rectifier diode
1SR156-400
Applications For fast rectifier Dimensions (Unit : mm) Land size figure (Unit : mm) 2.0
2.6±0.2
Features 1) Small power mold type. (PMDS) 2) High reliability. 3) High switching speed.
0 IR DISPERSION MAP
150
240 Ifsm 8.3ms 1cyc
50 Ta=25℃ IF=10mA IR=10mA Irr=0.10*IR n=10pcs Ifsm 8.3ms 30 8.3ms
REVERSE RECOVERY TIME:trr(ns)
230 220 210 200 190 180 170 160 trr DISPERSION MAP AVE:200.7ns
0
25
50
75
100
125
150
0
25
50
75
100
125
150
AMBIENT TEMPERATURE:Ta(℃) Derating Curveﾞ(Io-Ta)
CASE TEMPARATURE:Tc(℃) Derating Curveﾞ(Io-Tc)
30 No break at 30kV 25 20 15 10 5 0 C=200pF R=0Ω C=100pF R=1.5kΩ AVE:14.6kV
1SR156-400
Data Sheet
0.1
3 0A Io
3 0A Io t T VR D=t/T VR=200V Tj=150℃
高速超导闪电跳变接收器（非镍金属、RoHS合规）产品包装尺寸说明书
BYG24DH to BYG24JH
200 to 600 140
20 at 1
1.5
1.5 at 1
150
x
1.5
1.15 at 1
150
x
AR3PDH to AR3PJH
x
200 to 1000 120 (140)
3
1.6 (1.9) at 3
175
AR3PKH to AR3PMH
x
SMPC (TO-277A) 4.75 x 6.65 x 1.2
VISH AY INTERTECHN OLOGY, INC.
AVALANCHE RECTIFIERS
Sinterglass and Plastic
Ultrafast Avalanche Rectifiers (Halogen-Free, RoHS-Compliant)
Product
BYT53A to BYT53G BYV26A to BYV26E BYV27-50 to BYV27-200
2
1.1 at 1
175
x
x
n/a
x
No
200 to 400 100
3.0
1.1 at 3
x
x
x
200 to 400 100
3
1.1 at 3
20 at 1
x
x
x
4.2 x Ø 4.3
200 to 1000 100 (150) 3 (2.9) 1.6 (1.78) at 3
50 to 1000 100
3
1.4 at 3
x
x
x
x
x
x
800 to 1000 250
耐克限用化学物质清单Nike RSL-2016版
要求的实验报告范围产品中来自位物质浓度检测方法和评论
Bisphenol A (BPA)
食品接触物包括水壶和护口器。
Nike, Inc., 要求
在与食品接触的产品中禁止作为产品单元使用。
Chlorinated Phenols
NIke, Inc., Restricted Substances List & Sustainable Chemistry Guidance 限用物 质清 单和可持续 化学指 南
2016 年 1 月，1.0 版
请始终访问 确保您使用最新版本的限用物质清单 (RSL)。 请注意：本文档在线版本为官方版本。所有印刷版本均为非受控副本。
自 2016 年 4 月 14 日起（含）用于制 造 Nike、Nike 子公司或许可产品的所 有材料都必须遵从本文件的规定。 更多信息，请参阅第 22 页 Nike, Inc., RSL 实施指南。
•• 确保生产中限制使用或不使用目标物质。 •• 推动可持续性产品的创新。 本出版物还包含以下内容： •• Nike, Inc., 绿色化学项目总览 •• 限用物质清单 (MRSL) •• Nike, Inc. 纳米技术要求 •• Nike, Inc. 气味管理指南 •• Nike, Inc. 动物毛皮政策
Nike, Inc., 限用物质清单和可持续化学指南
2016 年 1 月
目录
3
总览
NIKE, Inc., Apparel（服装）、Footwear（鞋类）和 Equipment（装备）中使用的所有材料和成分的化学制品限制。
5 Nike, Inc., 限用物质清单
21 Nike, Inc., RSL 实施指南
合规
本文件第 22 页的 RSL 实施指南列举了每次 RSL 更新生效的日期。我们希望可以给供应商足够的时间去理解，采取措施使 产品符合规范；但也有一些特殊情况——比如出台了新法规——可能会导致通知时间变短。
FAIRCHILD USB1101 数据手册
USB1101
Pin Description
Pin Number Pin Name
1
Config
2
OE
3
DAT_VP
4
SE0_VM
5
GND
6
Suspnd
7, 8 9 10
Note 1: OE H Note 2: OE L
D, D VCCIO VCC
ry
I/O I I
I/O
I/O
2
USB1101
Preliminary
TABLE 2. Driver, Receiver, and Suspend Function Select
Suspnd L
Inputs
Transmit Mode Outputs
OE L L L L Suspnd L
DAT_VP L H L H
The USB1101 has the capability of serving Self Powered power supply configurations only but interfaces to mixed voltage supply applications.
TABLE 1. Function Select
(see Table 2); When in receive mode(Note 1) with Suspnd H DAT_VP outputs the D
data.
(see Table 1 and Table 2) Output drive is 2mA (min) buffer
When in transmit mode(Note 2) SE0_VM is a data input (CMOS level rela-
FAIRCHILD FQPF1P50 数据手册
现货库存、技术资料、百科信息、热点资讯，精彩尽在鼎好!FQPF1P50TO-220FG S D(Note 4)(Note 4, 5)(Note 4, 5) (Note 4)Notes:1. Repetitive Rating : Pulse width limited by maximum junction temperature2. L = 187mH, I AS = -1.03A, V DD = -50V, R G = 25 Ω, Starting T J = 25°C3. I SD ≤ -1.5A, di/dt ≤ 200A/µs, V DD ≤ BV DSS, Starting T J = 25°C4. Pulse Test : Pulse width ≤ 300µs, Duty cycle ≤ 2%5. Essentially independent of operating temperature∆BV DSS / ∆T J Breakdown Voltage Temperature CoefficientI D = -250 µA, Referenced to 25°C -----V/°C I DSS Zero Gate Voltage Drain Current V DS = -500 V, V GS = 0 V -----1µA V DS = -400 V, T C = 125°C -----10µA I GSSF Gate-Body Leakage Current, Forward V GS = -30 V, V DS = 0 V -----100nA I GSSRGate-Body Leakage Current, ReverseV GS = 30 V, V DS = 0 V----100nAOn CharacteristicsV GS(th)Gate Threshold Voltage V DS = V GS , I D = -250 µA -3.0---5.0V R DS(on)Static Drain-Source On-ResistanceV GS = -10 V, I D = -0.515 A --8.010.5Ωg FSForward TransconductanceV DS = -50 V, I D = -0.515 A -- 1.03--SDynamic CharacteristicsC iss Input Capacitance V DS = -25 V, V GS = 0 V, f = 1.0 MHz--270350pF C oss Output Capacitance--4050pF C rssReverse Transfer Capacitance--6.08.0pFSwitching Characteristicst d(on)Turn-On Delay Time V DD = -250 V, I D = -1.5 A,R G = 25 Ω--9.030ns t r Turn-On Rise Time --2560ns t d(off)Turn-Off Delay Time --2765ns t f Turn-Off Fall Time --3070ns Q g Total Gate Charge V DS = -400 V, I D = -1.5 A,V GS = -10 V--1114nC Q gs Gate-Source Charge -- 2.0--nC Q gdGate-Drain Charge--5.6--nCDrain-Source Diode Characteristics and Maximum RatingsI S Maximum Continuous Drain-Source Diode Forward Current -----1.03A I SM Maximum Pulsed Drain-Source Diode Forward Current-----4.12A V SD Drain-Source Diode Forward Voltage V GS = 0 V, I S = -1.03 A -----5.0V t rr Reverse Recovery Time V GS = 0 V, I S = -1.5 A,dI F / dt = 100 A/µs--200--ns Q rrReverse Recovery Charge--0.7--µCTRADEMARKSThe following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is not intended to be an exhaustive list of all such trademarks.ACEx™Bottomless™CoolFET™CROSSVOLT™E2CMOS™FACT™FACT Quiet Series™FAST®FASTr™GTO™HiSeC™ISOPLANAR™MICROWIRE™POP™PowerTrench®QFET™QS™Quiet Series™SuperSOT™-3SuperSOT™-6SuperSOT™-8SyncFET™TinyLogic™UHC™VCX™DISCLAIMERFAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.LIFE SUPPORT POLICYFAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR INTERNATIONAL.As used herein:1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, or (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user.2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.PRODUCT STATUS DEFINITIONSDefinition of TermsDatasheet Identification Product Status DefinitionAdvance Information Formative or InDesign This datasheet contains the design specifications for product development. Specifications may change in any manner without notice.Preliminary First Production This datasheet contains preliminary data, andsupplementary data will be published at a later date.Fairchild Semiconductor reserves the right to makechanges at any time without notice in order to improvedesign.No Identification Needed Full Production This datasheet contains final specifications. FairchildSemiconductor reserves the right to make changes atany time without notice in order to improve design. Obsolete Not In Production This datasheet contains specifications on a productthat has been discontinued by Fairchild semiconductor.The datasheet is printed for reference information only.。