SDS-823X Trusted Power System 03

合集下载

NETGEAR S350系列8口光纤猫咪网络管理开关操作指南说明书

1. Register With the NETGEAR Insight AppUse the NETGEAR Insight App to register your switch.1. On your iOS or Android mobile device, visit the app store, search forNETGEAR Insight, and download the latest app.2. Open the NETGEAR Insight app.3. If you did not set up a NETGEAR account, tap Create NETGEAR Account andfollow the onscreen instructions.4. Enter the email address and password for your account and tap LOG IN .5. Tap + in the upper right corner.6. Either use the camera on your phone to scan the serial number bar codelocated on the bottom of the switch, or type in the serial number. 7. Tap Go .8. Tap View Device to add the switch to a network.The switch is registered and added to your account.NETGEAR® S350 Series 8-Port Gigabit Ethernet Smart Managed Pro Switch (GS308T)NETGEAR® S350 Series 8-Port Gigabit PoE+ Ethernet Smart Managed Pro Switch with 2 SFP • Switch model GS308T or GS310TP• GS308T power adapter (varies by region) orGS310TP adapter with detatchable power cord (varies by region)•Installation guide2. Connect the SwitchNote: For more information, see the hardware installation guide which you can download from https:///support/.3. Check the PoE Status (GS310TP Only)PoE+ power is provided by the GS310TP switch on ports 1-8. The switch can supply up to 30W PoE+ (IEEE 802.3at) to each port, with a maximum PoE power budget of 55W across all active PoE+ ports.The PoE Max LED indicates the status of the PoE budget on the switch:• Off . Sufficient (more than 7W of) PoE power is available.• Solid yellow . Less than 7W of PoE power is available.• Blinking yellow . At least once during the previous two minutes, less than 7Wof PoE power was available.4. Discover the IP AddressAn IP address is required to configure your switch. The switch gets an IPaddress from a DHCP server (such as your router) by default. If your switch is not connected to a DHCP server, use the default IP address: 192.168.0.239.Note: Make sure that you are using the latest version of the app.1. On your mobile device, connect with WiFi to the same router as the switch.2. Open the NETGEAR Insight app and log in to your account.The current IP address of the switch is displayed.GS308T switchGaming consoleDesktopNETGEAR, Inc.350 East Plumeria DriveSan Jose, CA 95134, USA NETGEAR INTL LTDBuilding 3, University Technology Centre Curraheen Road, Cork, Ireland© NETGEAR, Inc., NETGEAR and the NETGEAR Logo are trademarks of NETGEAR, Inc. Any non‑NETGEAR trademarks are used for reference purposes only.SupportThank you for purchasing this NETGEAR product. You can visithttps:///support/ to register your product, get help, access the latest downloads and user manuals, and join our community. We recommend that you use only official NETGEAR support resources.Si ce produit est vendu au Canada, vous pouvez accéder à ce document en français canadien à https:///support/download/.(If this product is sold in Canada, you can access this document in Canadian French at https:///support/download/.)For regulatory compliance information including the EU Declaration of Conformity, visit https:///about/regulatory/.See the regulatory compliance document before connecting the power supply.Do not use this device outdoors. If you connect cables or devices that are outdoors to this device, see https:///000057103 for safety and warranty information.November 20185. Configure the SwitchWe recommend that you use a web browser on a computer or tablet to configure the switch.Note: If your computer is a Mac, use the NETGEAR Switch Discovery Tool, as described in the following section.1. Open a web browser from a computer or tablet connected to the samenetwork as your switch.You can use a WiFi or wired connection. 2. Enter the IP address of the switch.3. Enter the password.The default password is password . We recommend that you change the password to a more secure password.4. Click the Login button.Other Discovery and Configuration MethodsThe NETGEAR Switch Discovery Tool and the Smart Control Center Utility let you discover the IP address and configure the switch. •NETGEAR Switch Discovery Tool . You can use a Mac or a 64-bit Windows-based computer that is on the same network as the switch. You can use a WiFi or wired connection. When you discover the switch, this tool provides access to the local browser interface to c onfigure the switch. To download the NETGEAR Switch Discovery Tool, visit/support/product/netgear-switch-discovery-tool.aspx .•Smart Control Center Utility . You can use a Windows-based computer that is on the same network as the switch. This utility requires Adobe Air. If Adobe Air is not detected during Smart Control Center Utility installation, you are prompted to allow Adobe Air to be installed. To download this utility, visit /support/product/SCC .Note: If you cannot discover or configure the switch, you might need totemporarily disable the firewall, Internet security, or antivirus programs. Make sure to reenable these security services after you discover and configure the switch.PoE ConsiderationsThe PoE and PoE+ power supplied by the GS310TP switch is prioritized in ascending port order (from port 1 to port 8), with a total power budget of 55 watts with a 67.5 watt power adapter. If the power requirements for the attached powered devices (PDs) exceed the total power budget of the switch, the PD on the highest-numbered port is disabled to make sure that the PDs that are connected to the higher-priority, lower-numbered ports are supported first.Just because a PD is listed as an 802.3at PoE powered device does notnecessarily mean that it requires the maximum power limit of the specification. Many PDs require less power, allowing all eight PoE+ ports to be active simultaneously.The following table describes the PoE and PoE+ classes and switch allocations.Device ClassStandardClassDescription PowerReserved by the Device PowerDelivered to the Device*0PoE and PoE+Default power (full)15.4W0.44W–12.95W1PoE and PoE+Very low power4.0W 0.44W–3.84W2PoE and PoE+Low power 7.0W 3.84W–6.49W 3PoE and PoE+Mid power 15.4W 6.49W–12.95W 4PoE+ onlyHigh power30.0W12.95W–25.5W* Calculated with the maximum cable length of 328 feet (100 meters). Shorter cable lengths will provide power closer to the power reserved by the switch.。

矽力杰产品选型_恒佳兴电子专业电源IC

Single output step down (Buck) Converter Vin max < 7VSY8018A 2.5 5.5 0.45 / 0.6 ±2% 1.5 400/200 √Ultra Low Quiescent Current DFN2x2-8 SY8030L 2.5 5.5 0.6 2.25 0.6 ±1.5% 50 300/200 DFN2x2-6 SY8078B 1.85 5.5 0.6 3 0.4 ±2% 40 350/250 DFN1.45x1-6 SY8010 2.5 5.5 1 1.5 0.6 ±1.5% 50 200/150 DFN2x2-6 SY8011A 2.5 5.5 1 1.5 0.6 ±2% 40 230/150 DFN1.5x1.5-6 SY8061A 2.5 5.5 1 1.5 0.6 ±2% 60 260/170 Auto Discharge DFN2x2-6 SY8065L 2.5 5.5 1 1.5 0.6 ±2% 90 250/200 √SOT 23-6 SY8071 2.5 5.5 1 2 0.6 ±2% 40 260/170 SOT 23-5 SY8075 2.5 6.5 1 1.5 0.6 ±2% 40 260/170 DFN2x2-6 SY8077 2.5 6.5 1 1.5 0.6 ±2% 40 260/170 SOT 23-5 SY8080 2.5 5.5 1 3 0.6 ±2% 40 270/160 SOT 23-5SY8081 2.5 5.51 2.5 0.6 ±2%40230/150 Output auto discharge DFN1.5×1.5-6SY8011B 2.5 5.5 1.5 1.5 0.6 ±2%60210/130 DFN1.5x1.5-6SY8030 2.5 5.5 1.5 2.25 0.6 ±1.5%50200/150 Ext Mode DFN2x2-6 SY8002B 2.7 5.5 1.5 1 0.6 ±2% / 110/80 √Latch off protection SOT 23-6SY8002E 2.7 5.5 2 1 0.6 ±2% / 110/80 √Force PWM SOT 23-6SY8003L 2.7 5.5 2 1 0.6 ±2% 55 120/90 √DFN2x2-8Single output step down (Buck) Converter Vin max < 7V±2%SY8089 SOT 23-52.7 5.5 2 1 0.6 55 110/80 Latch off protectionSY8003C1 2.7 5.5 3 3 0.6 ±2% 55 110/80 √DFN2x2-8SY8823 2.5 5.5 3.5 2 0.6 ±1.5% 18 55/35 √QFN2x1.5-8SY8047 2.5 5.54 1.25 0.6 ±1.5%1875/55√QFN3x3-16SY8856 2.7 5.54 3 0.6 ±1.5%6035/15 √√DFN2x2-8√±1.5%SY8003F 2.7 5.5 3 1 0.6 / 110/80 DFN2x2-8 SY8079P 2.7 6.5 0.6 ±2% 55 125/95 Non latch off OVP SOT 23-6SY8032 2.7 5.5 2.5 0.6 ±2% 80 100/80 SOT 23-6SY8032E 2.7 5.5 2.5 0.6 ±2% 100/80 Force CCM SOT 23-6SY8003 2.7 5.5 0.6 ±2% 55 110/80 Latch SCP/OVP DFN2x2-8SY8003A 2.7 5.5 0.6 ±2% 55 110/80 Non-latch off protection DFN2x2-8SY8003C 2.7 5.5 0.6 ±2% 55 100/80 DFN2x2-8 SY8003E 2.7 5.5 0.6 ±2% 110/80 Force CCM DFN2x2-8 SY8043A 2.7 5.5 1.25 0.6 ±2% 18 75/55 DFN3x3-16 SY8047L 2.5 5.5 1.25 0.6 ±2% 18 75/55 QFN3x3-16 SY8859 2.7 5.5 0.6 ±1% 40 100/50 OVP/OCP/SCP/UVLO/OTP QFN1.5x1.5-7Single output step down (Buck) Converter Vin max < 7VPart Number Vin (min)(V)Vin (max)(V)Iout (max) (A) Fsw (MHz)Vout (min)( V)VoltageAcurracySY8824B 2.6 5.5 4 1.8 / ±1% SY8824C 2.6 5.5 4 1.8 / ±1% SY8035 2.7 5.5 5 1 0.6 ±1.5% SY8805A 3 5.5 5 1 0.6 ±1.5% SY8825 2.5 5.5 5 2 0.6 ±1.5% SY8876 2.7 6.5 6 1.2 0.6 ±1.5% SY8827K 2.5 5.5 6 2.4 ±1.5% SY8868 2.7 5.56 10.6 ±1% SY8099 2.7 5.5 6 1 0.6 ±1% SY8812 2.75 5.5 12 1 ±1%80 70/40Programmable Output Voltage: 0.7625Vto 1.55V in 12.5mV/step; Default 1.15Voutput voltage8015010018606550408070/4050/4035/1555/3538/1528/1735/1530/1212/6PackageTSOT 23-8Programmable Output Voltage: 0.7625Vto 1.55V in 12.5mV steps; Default 1.05Voutput voltageTSOT 23-8EXT SS DFN3x3-10DFN2x2-8QFN2x1.5-8OCP/UVLO/OTP DFN2x2-8I2C Programmable Vout: 0.7125V~ 1.5V CSP1.56x1.96-20in 12.5mV steps, Addr: 1000001xCOT mode,max dutyHigh efficiencyP rogrammable Output Voltage: 0.6V to1.5V in 10mV stepsQFN2x2-10TSOT 23-6QFN3x3-12Dual output step down (Buck) Converter Vin max < 7VPart Number Vin(min)(V)Vin(max)(V)Iout(max)(A)Fsw (MHz) Vout (min)(V)VoltageAcurracyQuiescentCurrent(uA)MO SFET Ron H/L (m? ) Power GoodOutputFeature/ Special Function PackageSY8020 2.5 5.5 1A x2 1.5 0.6 ±2% 50 200/150 Individual EN DFN3x3-12 SY8831 2.5 5.5 1A x2 1.5 0.6 ±2% 45/55 260/180 Individual EN TSOT 23-8 SY8832 2.5 5.5 2A x2 2 0.6 ±2% 35/45 125/100 Individual EN TSOT 23-8 SY8024 3 5.5 3A x2 1 0.6 ±2% 80 105/85 Individual EN DFN3x3-12 SY8821 2.5 5.5 1A/1.5A 2 0.6 ±2% 45 125/100 Individual EN DFN2x1.5-8Single output step down (Buck) Converter, Vin max > 7VuiescentOriginal Part Number Vin(min)(V)Vin(max)(V)Iout(max)(A)Fsw (MHz) Vout( imn)(V)Fixed O utputVoltage(V)VoltageAcurracyCurrent (uA)MOSFET(RonH/L) (m ? )Power oGodOutputFeature/ Special Function PackageSY8290 5 40 0.3 2 0.6 ±2.0% 160 2000/- SOT 23-6 SY8200 6 24 0.6 0.5 0.6 ±2% 400 420/200 SOT 23-6 SY8401 4.5 50 0.8 1.2 0.6 ±1.0% 150 700/- SOT 23-6SY8201 4.527 1 0.5 0.6 ±2%400350/150 SOT 23-6SY8201C 4.527 1 1.15 0.6 ±2%400350/150 Force CCM SOT 23-6SY85017 100 1 0.2~1MHz 1.2 ±2.0%400500/240 Programmable Switching Frequency SO8ESY8291 5 40 1.2 0.8 0.6 ±2.0% 160 180/- SOT 23-6 SY8502 7 100 1.8 0.2~1MHz 1.2 ±2.0% 400 500/240 Programmable Switching Frequency SO8ESingle output step down (Buck) Converter, Vin max > 7VVin(min) Vin(max) Iout(max) Fsw Vout(min) Voltage Quiescent MO SFET(Ron Power GoodPart Number(V) (V) Iout((m A)ax)(MHz) (V) Acurracy Current (uA) H/L) (m ? ) O utputFeature/ Special Function PackageSY8121 4.5 18 2 1 0.6 ±2% 400 170/160 SOT 23-6/ DFN2x2-6 SY8121B 4.35 18 2 1.2 0.6 ±2% 170/160 1.2MHz, FCCM SOT 23-6SY8120B1 4.5 18 2 0.5 0.6 ±2% 400 130/120 SOT 23-6SY8121C 4.5 18 2 1.2 0.6 ±2% 400 130/120 SOT 23-6SY8222 4.5 23 2 0.5 0.6 ±1.5% 400 150/110 √EXT SS, Hic-cup SCP DFN3x3-10SY8292 5 40 2 0.8 0.6 ±2.0% 160 180/- SOT 23-6SY8113B 4.5 18 3 0.5 0.6 ±1.5% 100 80/40 Hic-cup SCP TSOT 23-6SY8113C 4.518 3 1 0.6 ±1.5%10080/40 Hic-cup SCP TSOT 23-6SY8113D 4.5 18 3 0.5 0.6 ±1.5% 100 80/40 √Hic-cup SCP, EXT SS TSOT 23-8SY8113G 4.518 3 0.5 0.6 ±1.5%10080/40 Hic-cup SCP, FCCM TSOT 23-6SY8203A 4.523 3 1 0.6 ±1.5%400120/85 √EXT SS DFN3x3-10SY8223 4.523 3 0.5 0.6 ±1.5%400120/85 √EXT SS, Hic-cup SCP DFN3x3-10SY8253 4.5 23 3 0.5 0.6 ±1.5% 100 105/50 √EXT SS, Hic-cup SCP TSOT 23-8SY8303 4.5 40 3 0.5~2.5MHz 0.6 ±1.5% 18 70/110 TSOT 23-8 SY8293 5 40 3 0.8 0.6 ±2.0% 160 180/-SO8EPart Number Vin(min)(V)Vin(max)(V)Iout(max)(A)Fsw (MHz) Vout(min)(V)VoltageAcurracyQuiescentCurrent (uA)MO SFET(Ron H/L)(m ? )Power Good OutputFeature/ Special Function PackageSY8502 7 85 1.2 0.2~0.5 1.2 ±2.0% / 500/240 Programmable Switching FrequencyRangeSO8ESY8120B1 4.5 18 2 0.5 0.6 ±2% 400 130/120 SOT 23-6SY8121 4.5 18 2 1 0.6 ±2% 400 170/160 SOT 23-6/ DFN2x2-6 SY8121C 4.5 18 2 1.2 0.6 ±2% 400 130/120 SOT 23-6SY8222 4.5 23 2 0.5 0.6 ±1.5% 400 150/110 √EXT SS, Hic-cup SCP DFN3x3-10SY8292 5 40 2 0.8 0.6 ±2.0% 160 180/- SOT 23-6SY8113B 4.5 18 3 0.5 0.6 ±1.5% 100 80/40 Hic-cup SCP TSOT 23-6SY8113C 4.5 18 3 1 0.6 ±1.5% 100 80/40 Hic-cup SCP TSOT 23-6SY8113D 4.5 18 3 0.5 0.6 ±1.5% 100 80/40 √Hic-cup SCP, EXT SS TSOT 23-8SY8113G 4.5 18 3 0.5 0.6 ±1.5% 100 80/40 Hic-cup SCP, FCCM TSOT 23-6SY8203A 4.5 23 3 1 0.6 ±1.5% 400 120/85 √EXT SS DFN3x3-10SY8223 4.5 23 3 0.5 0.6 ±1.5% 400 120/85 √EXT SS, Hic-cup SCP DFN3x3-10SY8253 4.523 3 0.5 0.6 ±1.5%100105/50 √EXT SS, Hic-cup SCP TSOT 23-8SY8303 4.5 40 3 0.5~2.5MHz 0.6 ±1.5% 18 70/110 TSOT 23-8SY82935 40 3 0.8 0.6 ±2.0%160180/- SO8ESY8113H 4.5 18 3 0.5 0.6 ±1.5% 160 80/40 Programmable soft-start time TSOT 23-8±1.5%SY8104A4.518 4 0.5 0.6±1.5%100 50/30Instant PWM architectureSY8105 4.5 18 5 0.5 0.6±1.5%100 50/30SY8205 4.5 30 5 0.5 0.6±1.5%200 70/40√EXT SSSY8105A 4.5 18 5 0.5 0.6±1.5%100 40/20Instant PWM architectureSY8366H 4 28 6 0.8 0.6±1.5%100 40/20√Hic-cup SCP, 12A Peak current capability,programmable output current limitSY8286A 4 23 60.6 0.6 ±1.0% 12038/19 √SY8366K428 6 0.50.6±1.5%10040/20√Hic-cup SCP,6A continuous/12A peakoutput current capabilitySY8368A42880.80.6±1%100 20/10√Hic-cup SCP, 16A Peak current capability,programmable output current limitSY8288A 4 23 8 0.5 0.6 ±1.0% 80 30/10SY8288 4 23 8 0.5 0.6 ±1.0%8030/10SY8288C5.52380.60.6±1.5%10822/11√OVP/OCPSY8210A 4 28 10 0.6 0.6±1.5%300 25/8√Mem o ry power, 10A VDDQ/1A VTT LDO, 16A Peak Current capability, Latch offUVP/OVP, Over temperature alertSY8204 4.5 30 40.50.620080/50EXT SSPackageTSOT 23-6SO8ETSOT 23-6TSOT 23-6DFN3x4-12TSOT 23-6QFN3x3-12QFN3x3-20QFN3x3-12QFN3x3-12QFN3x3-20 QFN3x3-20QFN3x3-20QFN4x3-19Part Number Vin(min)(V)Vin(max)(V)Iout(max)(A)Fsw (MHz) Vout(min)(V) Voltage AcurracyQuiescent Current (uA)MO SFET(Ron H/L) (m ? ) Power Good OutputFeature/ Special Function Package SY8182 4 18 12 0.2~1MHz 0.6 ±1.0%18/6 √QFN4x4-20SY8182L 4.5 18 12 0.2~1MHz0.6 ±1.0% 500 18/6 √ Hic-cup SCP/OVPQFN4x4-24 SY8186418160.50.6±1.5%1507.5/2.5√Hic-cup SCP, programmble outputQFN4x4-11current limitPart NumberVin(min)(V)Vin(max)(V)Ilim (A)Fsw (MHz)Vout(max)(V)Sync BoostFixed O utputVoltage (V) Acu F r B ra /c y AcurracyInput Q uiescent Current (uA)Q uiescent current from output (uA)MO SFET Ro n (L/S) (m ? )Feature/ Special Function PackageSY7060L 0.7 5 0.2 / 5.25 Y /0.5V ±3% 0.518450/800SOT-363SY7070 0.7 5 0.35 / / Y 3.3 /0.5 5.5 500/700Bypass function @ shutdown SOT 23-5SY7070A 0.7 5 0.35 / / Y 3 / 0.5 5.5 500/700SOT 23-5SY7071 0.7 5 0.35 / 5.25 Y /1.0V ±3%0.5 5 500/700 Pass-through function @ shutdown SOT-363SY7071A 0.7 5 0.35 / / Y 5 / 0.5 7 400/500Pass-through function @ shutdown SOT-363SY7060 0.7 5 0.4 / 5.25 Y /0.5V ±3% 0.5 18 450/800SOT-363SY7080 0.9 4 1.8 1.2 4 Y / 1.2V ±3%65 / 90/200 Output Disconnect @Shutdown SOT 23-6Single output step Up (Boost) Converter (Low V oltage)Part NumberVin(min)(V)Vin(max)(V)Ilim (A)Fsw (MHz)Vout(max)(V)Sync BoostFixed O utput Voltage (V)Acu F rr B a /c y Acurracy InputQuiescent Current (uA) Quies cent current from output (uA) MOSFET Ron(L/S) (m ?) Feature/ Special Function PackageSY7063 1.8 5.25 3 0.5 5.5 Y / 1.2V ±1.5% 102736/40Output Disconnect @Shutdown QFN2x2-10SY7069 2.5 5.5 3 1 5.5 Y / 1.2V±1.5% 8 32 50/90TSOT 23-6SY7088 2.3 5 3 1 5.5 Y / 1.2V ±1.5% 2 30 70/85DFN2x3-8SY7088E 2.3 5 3 1 5.5 Y / 1.2V ±1.5% / / 70/85DFN2x3-8SY7065 1.8 5.25 5 0.5 5.5 Y / 1.2V ±1.5% 10 27 20/40 Auto output discharge function QFN2x2-10SY7065A 1.8 5.25 5 0.5 5.5 Y / 1.2V ±1.5% 10 27 20/40No output discharge function QFN2x2-10SY7076 2 5.5 6 0.5 5.5 Y / 1.2V ±1.5% 10 27 20/40QFN2x2-10SY7066 1.8 5.25 6 0.5 5.5 Y / 1.2V ±1.5% 10 27 20/40 Auto output discharge function QFN2x2-10SY7066B 1.8 5.25 6 0.5 5.5 Y / 1.2V ±1.5%10 27 20/40 Selectable Forced PWM mode QFN2x2-10Single output step Up (Boost) Converter (Low V oltage)SY9701A 2.6 5.5 1.2 1 5.5 0.6V ±1.5% 60 100/100 Output Disconnect @Shutdown DFN3x3-14Single output step Up (Boost) Converter (High Voltage)PackagePart NumberVin(min)(V)Vin(max)(V)Ilim (A)Fsw (MHz) Vout (max) (V) Sync BoostFB/ AcurracyInput Q uiescent Current (uA) MO SFET (RonMain/Rectified)(m? )Disconnect FET Ron ( m ?) Power Good OutputFeature/ Special FunctionSY7208C 3 25 0.6 1 25 N0.6V ±2%100 150/-Int SS/CompSOT 23-6SY7152A 3 8 2 1 16 N0.6V ±2%100 130/-Int SS/Comp SOT 23-6SY7208L 3 25 2 1 25 N0.6V ±2%100 150/-Int SS/Comp SOT 23-6SY7302 3 33 2 1 33 N0.6V ±2% 100 200/-Int SS/Comp SOT 23-6SY7388 3.5 30 2 0.85 30 N 1V ±2%150 200/-Accurate input current limit SOT 23-6SY7102 2 6 2.5 1 6 N0.6V ±2% 200 120/-Int SS/Comp SOT 23-6SY7801 2.5 5.5 2.5 1 / N 0.6V ±2%200 120/-Int SS, with 2A 80m? Load Switch DFN3x3-12SY7104A2 6 4 1 6 N0.6V ±2% 100 90/-Int SS/Comp DFN3x3-10SY7304 3334133N 0.6V ±2%100120/-QFN3x3-10SY7205 8.6 15.9 4.5 0.5 16 N1.25V±1.5% 120 75/-Adjustable soft-start time, OVP DFN3x3-10SY7982 3 9 6 1 13 Y 1V ±2% 600 80/4040√True shutdown QFN3x3-16SY7219 3 5.5 9 / 36 N 1.25V ±2%350 65/-EXT Comp DFN3x3-10 SY721531615/18Y1V ±1.5% 22016/1818√Int SS, OVP/SCP/ True shutdown ProgrammableSwitching Frequency: 0.2~1MHz QFN4x4-18SY7215A31615/18Y 1V ±1.5%2309/1212√Int SS, OVP/SCP/ True shutdown ProgrammableSwitching Frequency: 0.2~1MHzQFN4x4-181.23VInt SS; Adjustable current limit for optical module;SY7501B2.955.50.930.480N ±2%225 800/-Current limit indicator; Accurate high-side currentQFN3x3-16monitor; 320mW maximum output powerDC-DC PWM Controller (external Switch)Original Part Number Vin(min)(V)Vin(max)(V)Fsw (MHz)V(V R)EFFunction PackageSY7901 3 25 0.5 1 Current mode DC/DC controller targeted for Boost, Sepic, Flyback and Forward applications with DC Input Current Limit DFN3x3-10 SY7902A 3 25 0.3 1 Current mode DC/DC controller targeted for both Boost and Sepic applications with DC Output Current Limit SOP10 Power ModulePart Number Vin(min)(V)Vin(max)(V)Iout(max)(A)Fsw (MHz)Fixed O utputVoltage (V)Voltage Acurracy Q uiescent Current (uA) MOSFET (Ron H/L) (m? ) Integrated Inductor PackageSY98081 2.5 5.5 0.6 3 ±2% 40 230/150 √QFN2x1.5-8 SY98001 2.5 5.5 1.2 3 ±2% 40 230/150 √QFN2.5x2-8 SY98003 2.7 5.5 3 3 ±1.5% 60 35/15 √QFN3x3-10 SY98004 2.7 5.5 4 3 ±1.5% 60 35/15 √QFN3x3-10 SY98002 2.7 5.5 2 3 ±1.5% 60 20/40 √QFN3x3-10 SY98202 4.5 23 2 2 ±1.5% 100 50/105 √QFN3x3-10 SY98195 4.5 18 5 1.5 ±1.5% 15/50 √QFN5x5-20LDO RegulatorPart Number Vin(min)(V)Vin(max)(V)Vout(V)Iout(A)Dropout Voltage (mV) Function PackageSY6340 2.3 30 Output Voltage Adjustable 0.15 300 LDO Reg SOT23-5D FN2×2-6 SY6340B 3.6 30 3.3 0.05 100 LDO Reg SOT 23-5SY6345 4 40 Adjustable 0.3 300 LDO Reg SOT 23-5SY6301 1.6 5.5 Output Voltage Adjustable 1 0.32V at I OUT =1A, V OUT =1.5V0.18V at I OUT =1A, V OUT =2.8VLDO Reg DFN3×3-6SY6307B 0.8 5.5 Output Voltage Adjustable 0.5 90 LDO Reg DFN1.2x1.2-6 Protection SwitchPart Number Package Enabl eLogic O CP O VP No. ofChannelsVin(V) Vout(V) Iout(A) Rds(on) TUV/CBCertificateULCertificateSpecial FunctionSY6280A SOT 23-5 H Y N 1 2.4~5.5 2.4~5.5 0.4~2 63m? Programmable current limit, reverse blockingSY6281A SOT 23-5 L Y N 1 2.4~5.5 2.4~5.5 0.4~2 63m? Programmable current limit, reverse blockingSY6288A SOT 23-5 H Y N 1 2.5~5.5 2.5~5.5 0.6 80m? √√Output discharge at shutdown Reverse Blocking,OCB indicatorSY6288B SOT 23-5 L Y N 1 2.5~5.5 2.5~5.5 0.6 80m? ? ? Output discharge at shutdown Reverse Blocking,OCB indicatorSY6811 CSP0.9x0.9-4 H N N 1 1.05~1.95 1.05~1.95 1 45m?@VIN=1.2V35m?@VIN=1.8V Auto output cap discharge function, utra low inputvoltageSY6819A SO8 H Y N 1 4.5~18 4.5~18 1.2 110m?@VIN=12V Programmable blanking t ime for DFF control, Default Off when EN ONSY6819 SO8 H Y Y 1 4.5~18 4.5~18 1.2 110m?@VIN=12V Programmable blanking t ime for DFF control,Default On when EN ONSY6288C20 SOT 23-5 H Y N 1 2.5~5.5 2.5~5.5 2 65m? ? ? Output discharge at shutdown Reverse Blocking,OCB indicatorSY6288D20 SOT 23-5 L Y N1 2.5~5.5 2.5~5.5265m? √√Output discharge at shutdown Reverse Blocking,OCB indicatorPart Number Package EnableLogicOCP OVPNo. ofChannelsVin(V) Vout(V) Iout(A) Rds(on)TUV/CBCertificateULCertificateSpecial FunctionSY6882A DFN2x2-8 H N Y 1 3~23 3~23 2 100m?Internal Fixed Over-Voltage Protection Threshold @7.1V, Thermal Shutdown Protection&Auto RecoverySY6882B DFN2x2-8 H N Y 1 3~23 3~23 2 100m? Programmable OVP Threshold Thermal Shutdown Protection& Auto RecoverySY6883 SOT 23-6 L N Y 1 3~23 3~23 2 100m? Programmable OVP Threshold Thermal Shutdown Protection& Auto RecoverSY6822 QFN2x2-10 L Y N 1 3~6.6 3~6 2 60m? Bidirectional Current Limit SwitchSY6288C7 SOT 23-5 H Y N 1 2.5~5.5 2.5~5.5 2.5 70m? √Output discharge at shutdown Reverse Blocking,OCB indicatorSY6288D7 SOT 23-5 L Y N 1 2.5~5.5 2.5~5.5 2.5 70m? √Output discharge at shutdown Reverse Blocking,OCB indicatorSY6288C5 MSOP8 H Y N 1 2.5~5.5 2.5~5.5 2.5 70m? √√Output discharge at shutdown Reverse Blocking,OCB indicatorSY6288D5 MSOP8 L Y N 1 2.5~5.5 2.5~5.5 2.5 70m? √√Output discharge at shutdown Reverse Blocking,OCB indicatorSY6288E1 SOT 23-5 H Y N 1 2.5~5.5 2.5~5.5 3 45m? √√Output discharge at shutdown Reverse Blocking,OCB indicatorSY6288E2 SOT 23-5 L Y N 1 2.5~5.5 2.5~5.5 3 45m? √√Output discharge at shutdown Reverse Blocking,OCB indicatorSY6288F1 SOT 23-6 H Y N 1 2.5~5.5 2.5~5.5 3 45m? √Output discharge at shutdown Reverse Blocking,OCB indicatorSY6288F2 SOT 23-6 L Y N 1 2.5~5.5 2.5~5.5 3 45m? √Output discharge at shutdown Reverse Blocking,OCB indicatorSY6283A DFN1.2×1.6-4 H Y N 1 2.5~5.5 2.5~5.5 3 60m? Output discharge at shutdown Reverse Blocking SY6283 DFN1.2×1.6-4 H Y N 1 2.5~5.5 2.5~5.5 3 60m? Reverse blocking output, ultra low input voltage SY6813 6 ball CSP H N N 1 1.2~5.5 1.2~5.5 3 22m? Auto output cap discharge functionPart Number Package EnableLogicOCP OVPNo. ofChannelsVin(V) Vout(V) Iout(A) Rds(on)TUV/CBCertificateULCertificateSpecial FunctionSY6288D20 SOT 23-5 L Y N 1 2.5~5.5 2.5~5.5 2 65m? √√Output discharge at shutdown Reverse Blocking,OCB indicatorSY6882A DFN2x2-8 H N Y 1 3~23 3~23 2 100m?Internal Fixed Over-Voltage Protection Threshold @7.1V, Thermal Shutdown Protection&Auto RecoverySY6882B DFN2x2-8 H N Y 1 3~23 3~23 2 100m? Programmable OVP Threshold Thermal Shutdown Protection& Auto RecoverySY6883 SOT 23-6 L N Y 1 3~23 3~23 2 100m? Programmable OVP Threshold Thermal Shutdown Protection& Auto RecoverSY6822 QFN2x2-10 L Y N 1 3~6.6 3~6 2 60m? Bidirectional Current Limit SwitchSY6288C7 SOT 23-5 H Y N 1 2.5~5.5 2.5~5.5 2.5 70m? √Output discharge at shutdown Reverse Blocking,OCB indicatorSY6288D7 SOT 23-5 L Y N 1 2.5~5.5 2.5~5.5 2.5 70m? √Output discharge at shutdown Reverse Blocking,OCB indicatorSY6288C5 MSOP8 H Y N 1 2.5~5.5 2.5~5.5 2.5 70m? √√Output discharge at shutdown Reverse Blocking,OCB indicatorSY6288D5 MSOP8 L Y N 1 2.5~5.5 2.5~5.5 2.5 70m? √√Output discharge at shutdown Reverse Blocking,OCB indicatorSY6288E1 SOT 23-5 H Y N 1 2.5~5.5 2.5~5.5 3 45m? √√Output discharge at shutdown Reverse Blocking,OCB indicatorSY6288E2 SOT 23-5 L Y N 1 2.5~5.5 2.5~5.5 3 45m? √√Output discharge at shutdown Reverse Blocking,OCB indicatorSY6283A DFN1.2× 1.6-4 H Y N 1 2.5~5.5 2.5~5.5 3 60m? Output discharge at shutdown Reverse Blocking SY6283 DFN1.2× 1.6-4 H Y N 1 2.5~5.5 2.5~5.5 3 60m? Reverse blocking output, ultra low input voltage SY6813 6 ball CSP H N N 1 1.2~5.5 1.2~5.5 3 22m? Auto output cap discharge functionPart Number Package EnableLogicOCP OVPNo. ofChannelsVin(V) Vout(V) Iout(A) Rds(on)TUV/CBCertificateULCertificateSpecial FunctionSY6823 DFN2x2-8 H N N 2 0.6~5.5 0.6~5.5 4 28m? Programmable turn-on delay& ramp-up time,integrated OTP SCPSY6818 CSP1.73x1.73-12 H N Y 1 2.5~30 2.5~20 5 R PWPT =53m? (typ) Programmable OVP with Integrated Reverse Blocking FET, acurrate current level indicatorSY6874 DFN3x3-10 H Y Y 1 2.5~30 2.5~14 4 50m? Programmable softstart&current limit,3.3V/5V/12V selectable clamping outputSY6875A DFN3x3-10 H Y Y 1 2.5~30 2.5~14 5 40m? Programmable softstart&current limit,3.3V/5V/12V selectable clamping outputSY6875C DFN3x3-10 H Y Y 1 2.5~30 2.5-14 5 40m? Programmable softstart&current limit, 3.3V/5V/12V selectable clamping outputSY6875D DFN3x3-10 H Y Y 1 2.5~30 2.5-14 5 40m? Programmable softstart&current limit, 3.3V/5V/9V selectable clamping outputSY6875F DFN3x3-10 H Y Y 1 2.5~30 2.5-14 5 50m? Programmable softstart&current limit,3.3V/5V/12V selectable clamping outputSY6895A DFN3x3-10 H Y Y 1 2.5~12 2.5~6.5 5 40m? Fixed Current Limit, Prog.SS SY6895C DFN3x3-10 H Y Y 1 2.5~12 2.5~6.5 5 40m? Fixed Current Limit, Prog.SSSY6880C CSP1.8x2-12 H N Y 1 2.5~28 0~7 5A continous,8A peak38m?Fixed intenal OVP@6.8V, Reverse block, Surgeprotection up to 80VSY6880A CSP1.8x2-12 H N Y 1 2.5~28 0~7 5A continous,8A peak 38m?SY6829 CSP0.79x0.79-4 H N Y 1 2.5~6 0~7 1 96m? Precise clamping output voltageSwitching ChargerPart Number Function Vin (V)Max. ChargeCurrent (A)Fsw (MHz) Series Cells Cell Voltage Special Function PackageSY6903A Single-Cell Bi-directional Power Bank 4.5-5.5 2 0.5 Single Cell 4.2V adaptive current limit, 2.4A Boost QFN3x3-16 SY6923 Single-Cell with USB-OT G 4~6 1.55 3 Single Cell 3/5~4.44V Compliance with USB and USB OT G, MTK reference design CSP 1.93x2.05-20 SY6923D Single-Cell with USB-OT G 4~6 1.55 3 Single Cell 3.5~4.44V Compliance with USB and USB OTG CSP 1.93x2.05-20 SY6923D1 Single-Cell with USB-OT G 3.5- 4.44 1.25/1.55 3 Single Cell 4.2V Compliance with USB and USB OTG CSP 1.93x2.05-20SY6932 Multi-cell Charger Step Down Reg. 4~23 2 0.8 1-3 Cells 4.2VProg. Charge Current&Timer，Output Power PathManagementQFN4x4-16SY6952A Single-cell Charger Step Down Reg. 4~23 2 0.8 Single Cell 4.2V,4.35V Power Path Management and Adaptive Input Current Limit QFN4x4-16 SY6952C Single-cell Charger Step Down Reg. 4~23 2 0.8 Single Cell 4.2V, 4.35V Power Path Management and Adaptive Input Current Limit DFN3x3-12 SY6952B1 Single-cell Charger Step Down Reg. 4~23 2 0.8 Single Cell 4.1V, 4.4V Adaptive Input Current Limit SO8ESY6982C 2 cell Boost Li-Ion Baterry Charger 3.6~5.5 2 1 2 Cells 4.2V, 4.35V Prog. Charge Current&T imer，Adaptive Input Current Limit QFN3x3-16SY6982C1 2 cell Boost Li-Ion Baterry Charger 3.6~5.52 12 Cells 4.1V, 4.25V Prog. Charge Current&T imer，Adaptive Input Current Limit QFN3x3-16 SY6982D 2 cell Boost Li-Ion Baterry Charger 3.6~5.5 2 1 2 Cells 4.1V, 4.2V, 4.3V, 4.35V Prog. Charge Current&T imer，Adaptive Input Current Limit QFN3x3-16SY6982E2 cell Boost Li-Ion Baterry Charger 3.6~5.52 12 Cells 4.2V, 4.35VProg. Charge Current&T imer，Adaptive Input Current LimitQFN3x3-16SY6982E12 cell Boost Li-Ion Baterry Charger 3.6~5.52 12 Cells 4.25V, 4.4VProg. Charge Current&T imer，Adapter and BAT IN IndicatorQFN3x3-16SY6982F 2 cell Boost Li-Ion Baterry Charger 3~5.5 2 1 2 Cells 4.2V Prog. Charge Current&T imer，Adapter and BAT IN Indicator QFN3x3-16 SY6903 Single-Cell Bi-directional Power Bank 4.5~5.35 2 0.5 Single Cell 4.2V 3in1, Adaptive current limit, 2.4A Boost QFN3x3-16 SY6903B Single-Cell Bi-directional Power Bank 4.5~5.3520.5 Single Cell 4.35V 3in1, Adaptive current limit, 2.4A Boost QFN3x3-16Part Number Function Vin (V)Max. ChargeCurrent (A)Fsw (MHz) Series Cells Cell Voltage Special Function PackageSY6908 Single-Cell Bi-directional Power Bank 4.5~5.35 2 0.5 Single Cell 4.2V 3in1, Adaptive current limit, 2.5A Boost QFN3x3-16SY6908A Single-Cell Bi-directional Power Bank 4.5~5.5 2 0.5 Single Cell 4.2V 3in1, Adaptive current limit, 2.5A Boost QFN3x3-16 SY6908B Single-Cell Bi-directional Power Bank 4.5~5.35 2 0.5 Single Cell 4.35V 3in1, Adaptive current limit, 2.5A Boost QFN3x3-16 SY6908D Single-Cell Bi-directional Power Bank 4.5~5.35 2 0.5 Single Cell 4.2V 3in1, Adaptive current limit, >10000mAH BAT, 2.5A Boost QFN3x3-16 SY6908E Single-Cell Bi-directional Power Bank 4.5~5.35 2 0.5 Single Cell 4.35V 3in1, Adaptive current limit, >10000mAH BAT, 2.5A Boost QFN3x3-16 SY6918 Single-Cell Bi-directional Power Bank 4.5~5.35 2 0.5 Single Cell 4.2V,4.35V Prog. current limit, 18V input voltage surge QFN3x3-16 SY6918A Single-Cell Bi-directional Power Bank 4.5~5.35 2 0.5 Single Cell 4.2V,4.35V Prog. current limit, 18V input voltage surge QFN3x3-16SY6918B Single-Cell Bi-directional Power Bank 4.5-5.3520.5 Single Cell 4.2V, 4.35V Prog. current limit, 18V input voltage surge QFN3x3-16SY6990 Single-Cell Bi-directional Power Bank 4~13.5 5 0.5 Single Cell 4.1V,4.2V,4.25V,4.4VI2C controlled, USB Complianced, 5V/3A&12V/1.2A Boost QFN4x4-24SY6992 Single-Cell Bi-directional Power Bank 4~13.5 5 0.5, 0.3 Single Cell 4.1V,4.2V,4.25V,4.4V I2C controlled, USB Complianced, 5V/4A&12V/1.5A Boost QFN4x4-20SY6993 Single-Cell Bi-directional Power Bank 4~13.5 5 0.5, 0.3 Single Cell 4.1V,4.2V,4.25V,4.4VI2C controlled, USB Complianced, 5V/4A&12V/1.5A Boost QFN4x4-20 SY6935 High Current Step-down Charger 4~14 3.5 1 1-2 Cells 4.2V, 4.35V Adaptive input current limit, Blocking FET integrated QFN3x3-16 SY7994 Synchronous Boost converter with QC3.0 3~4.5 NA 0.3, 0.5 Single Cell NA QC3.0 Compliance QFN4x4-20Power Management I CsPart Number Vin(min)(V)Vin(max)(V)Num ber ofChannelsPackage Application Integrated FunctionSY8675 9.3 18 3 SO8E TV power system 1 synchronous buck, 1 sy cnh ronous buck, 1 load switchSY8670 8 25 6 QFN5X5-32 TV Power System 4-Channel Step-Down onCve rter, 2-Channel LDOSY8632A 4.5 18 3 QFN5x5-32 TCON Power System I2C controlled 3-channel Buck RegulatorsSY6401A 4 18 1 DFN3x3-10 SSD Programmable charging current Automatic bi-directional energy flowSY6402 2.7 16 1 QFN3x4-19 SSD Input-side current limit switch Bi-directional DC-DC Regulator wit disconnhe ct switch: Boost Charging Mode and Buck Discharging Mode SY8645 3.4 5.5 8 QFN5x5-32 POS 4 Buck Converter, 2 LDO, one MOS switch, one load switch&one voltage detector.SY7630 2.5 5.5 3 QFN4x4-24 Monitor/NB LCD Panel Power AVDD Boost, VGH/VGL charge pump, VCOM OPAMP, GPMSY7630B 2.3 5.5 3 QFN4x4-24 Monitor/NB LCD Panel Power AVDD Boost, VGH/VGL charge pump, VCOM OPAMP, GPMSY8671 9.1 14.7 6 QFN6X6-40 TV LCD Panel Power 1 AVDD Boost, 1 HAVDD Buck, 2 Buck, 1 VON Boost, 1 VOFF Buck-BoostSY8673 8 18 5 QFN7x7-48 TV LCD Panel Power AVDD Boost, VGH/VGL charge pump, VCOM OPAMP, GPM, DVDD, Gammar reference LDOSY7615 8 18 2 DFN3x3-10 wer supply and control for satellite set t Boost, LNB BlogSY7615A8 18 2 DFN3x3-10 LNB power supply and control for s at elliteset top boxesBoost, LNB BlogSY8631 2.5 5.5 6 QFN4x4-24 Camera module Step Down Buck Regulators,3 Low Dropout LDO and 1 Channel RESET OutputSY86304 20 3DFN3x3-12 Security CCD Camera power supply 2 Buck converters and 1 Boost converterSY86412 5 5QFN3x3-16 3D Glass 1 Boost output with analog switches for 3D glassesSY8660C 2.7 5.5 1 DFN3x3-14 U SB Powered Devices Buck converter with programmable current limit switchSY8689 4.5 18 3 QFN4x4-24 TV Power/USB Ports and Hubs/Set-Top Dual synchronous buck regulator and an N-channel back-to-back power MOSFET switch。

刷机错误代码说明

【1002 错误】平台不对，换刷机工具【1003 错误】平台不对【解决办法】：换平台，建议换6752最新平台刷!【1011 错误】平台错误【解决办法】：换对应mtk刷机平台！【1012 错误】尾插问题【解决办法】：换个尾插即可完美解决！【1013 错误】打开端口失败或者电池问题【解决办法】：1.驱动有问题2.重启电脑3.主板问题，红色进度条后不走，等几秒钟后报错10134.先拔掉电池，然后按住音量+键不放，再装回电池，最后再插入电脑，如果还不行换个USB口即可！【1014 错误】刷机包不对【解决办法】：资料cpu不对，例如6575刷成了6577，换资料解决问题，这个问题跟8200错误一样！【1018 错误】基带被加密【解决办法】：换原厂加密刷机工具！【1022 错误】刷机软件版本和手机不匹配、或者USB 接口不好用，刷机平台不行！【解决办法】：先换个USB 端口刷，不行的话建议去载个最新刷机软件试试去！或者换刷机工具！【1036 错误】原因是手机内存己经损坏【解决办法】：请更换硬件或直接去售后维修【1037 错误】你的刷机包版本不对或者是操作方式不对【解决办法】：请更换刷机包如果你确定你的刷机包是正确的请把DA DL All... 这个勾选取消掉，然后点击Download进行刷机，如果你的平台是中文版的点击“下载”这个按钮进行刷机，英文版本的是“Download”按钮！【1040 错误】S_UNSUPPORTED_OPERATION 刷机引导文件Scatter.txt 不匹配【解决办法】：下载适合你的机器的线刷ROM，很明显这个山寨机会遇到！比如机器是双核6577，但是下载的刷机ROM 是单核6575 的所以会报错【1041 错误】常见字库引起的问题！【解决办法】：如果刷机包的版本符合手机的版本，基本可以断定是字库问题，目前除了更换字库以外貌似没有更好的解决方法！【2004 错误】数据线连接电脑时出现的问题【解决办法】：建议更换其他的usb接口，如果还是不像请更换数据线或者电脑再刷，或者可能是基带被加密，常见于6571，换原厂加密平台刷机！【2005 错误】S_BROM_CMD_STARTCMD_FAIL【解决办法】：1.联机手法不对，重新联机。

摩克斯 EDS-2018-ML 系列 16+2G 端口无管理 Gigabit 以太网开关说明书

EDS-2018-ML Series16+2G-port Gigabit unmanaged Ethernet switchesFeatures and Benefits•2Gigabit uplinks with flexible interface design for high-bandwidth dataaggregation•QoS supported to process critical data in heavy traffic•Relay output warning for power failure and port break alarm•IP30-rated metal housing•Redundant dual 12/24/48VDC power inputs•-40to 75°C wide operating temperature range (-T models)CertificationsIntroductionThe EDS-2018-ML series of industrial Ethernet switches have sixteen 10/100M copper ports and two 10/100/1000BaseT(X)or 100/1000BaseSFP combo ports,which are ideal for applications that require high-bandwidth data convergence.Moreover,to provide greater versatility for use with applications from different industries,the EDS-2018-ML Series also allows users to enable or disable the Quality of Service (QoS)function,broadcast storm protection,and port break alarm function with DIP switches on the outer panel.The EDS-2018-ML Series has 12/24/48VDC redundant power inputs,DIN-rail mounting,and high-level EMI/EMC capability.In addition to its compact size,the EDS-2018-ML Series has passed a 100%burn-in test to ensure it will function reliably in the field.The EDS-2018-ML Series has a standard operating temperature range of -10to 60°C with wide-temperature (-40to 75°C)models also available.SpecificationsEthernet Interface10/100BaseT(X)Ports (RJ45connector)16Auto MDI/MDI-X connectionFull/Half duplex modeAuto negotiation speedCombo Ports (10/100/1000BaseT(X)or 100/1000BaseSFP+)2Auto negotiation speedAuto MDI/MDI-X connectionFull/Half duplex modeStandardsIEEE 802.3for 10BaseTIEEE 802.3u for 100BaseT(X)IEEE 802.3ab for 1000BaseT(X)IEEE 802.3z for 1000BaseXIEEE 802.3x for flow controlIEEE 802.1p for Class of Service DIP Switch ConfigurationEthernet Interface Quality of Service (QoS)Broadcast storm protectionPort break alarmInput/Output InterfaceAlarm Contact Channels Relay output with current carrying capacity of 1A @24VDCSwitch PropertiesMAC Table Size8KPacket Buffer Size4MbitsProcessing Type Store and ForwardPower ParametersConnection1removable6-contact terminal block(s)Input Current0.277A@24VDCInput Voltage12/24/48VDCRedundant dual inputsOperating Voltage9.6to60VDCOverload Current Protection SupportedReverse Polarity Protection SupportedPhysical CharacteristicsHousing MetalIP Rating IP30Dimensions58x135x95mm(2.28x5.31x3.74in)Weight683g(1.51lb)Installation DIN-rail mountingWall mounting(with optional kit)Environmental LimitsOperating Temperature EDS-2018-ML-2GTXSFP:-10to60°C(14to140°F)EDS-2018-ML-2GTXSFP-T:-40to75°C(-40to167°F) Storage Temperature(package included)-40to85°C(-40to185°F)Ambient Relative Humidity5to95%(non-condensing)Standards and CertificationsSafety UL61010-2-201EN62368-1(LVD)EMC EN55032/35EN61000-6-2/-6-4EMI CISPR32,FCC Part15B Class AEMS IEC61000-4-2ESD:Contact:6kV;Air:8kVIEC61000-4-3RS:80MHz to1MHz:20V/mIEC61000-4-4EFT:Power:2kV;Signal:2kVIEC61000-4-5Surge:Power:2kV;Signal:2kVIEC61000-4-6CS:10VIEC61000-4-8PFMFHazardous Locations Class I Division2IECExATEXMaritime DNVLRABSNKRailway EN50121-4Traffic Control NEMA TS2Vibration IEC60068-2-6Shock IEC60068-2-27Freefall IEC60068-2-32MTBFTime1,776,132hrsStandards Telcordia(Bellcore),GB WarrantyWarranty Period5yearsDetails See /warranty Package ContentsDevice1x EDS-2018-ML Series switch Installation Kit2x cap,plastic,for SFP port4x cap,plastic,for RJ45port Documentation1x quick installation guide1x warranty card DimensionsOrdering InformationModel Name 10/100BaseT(X)Ports(RJ45connector)Combo Ports(10/100/1000BaseT(X)or100/1000BaseSFP+)Operating Temp.EDS-2018-ML-2GTXSFP162-10to60°C EDS-2018-ML-2GTXSFP-T162-40to75°CAccessories(sold separately)SFP ModulesSFP-1FEMLC-T SFP module with1100Base multi-mode,LC connector for2/4km transmission,-40to85°C operatingtemperatureSFP-1FESLC-T SFP module with1100Base single-mode with LC connector for40km transmission,-40to85°Coperating temperatureSFP-1FELLC-T SFP module with1100Base single-mode with LC connector for80km transmission,-40to85°Coperating temperatureSFP-1GTXRJ45-T SFP module with11000BaseT port with RJ45connector for100m transmission,-40to75°C operatingtemperatureSFP-1GSXLC SFP module with11000BaseSX port with LC connector for300m/550m transmission,0to60°Coperating temperatureSFP-1GSXLC-T SFP module with11000BaseSX port with LC connector for300m/550m transmission,-40to85°Coperating temperatureSFP-1GLSXLC SFP module with11000BaseLSX port with LC connector for1km/2km transmission,0to60°Coperating temperatureSFP-1GLSXLC-T SFP module with11000BaseLSX port with LC connector for1km/2km transmission,-40to85°Coperating temperatureSFP-1GLXLC SFP module with11000BaseLX port with LC connector for10km transmission,0to60°C operatingtemperatureSFP-1GLXLC-T SFP module with11000BaseLX port with LC connector for10km transmission,-40to85°C operatingtemperatureSFP-1GLHLC SFP module with11000BaseLH port with LC connector for30km transmission,0to60°C operatingtemperatureSFP-1GLHLC-T SFP module with11000BaseLH port with LC connector for30km transmission,-40to85°C operatingtemperatureSFP-1GLHXLC SFP module with11000BaseLHX port with LC connector for40km transmission,0to60°C operatingtemperatureSFP-1GLHXLC-T SFP module with11000BaseLHX port with LC connector for40km transmission,-40to85°Coperating temperatureSFP-1GZXLC SFP module with11000BaseZX port with LC connector for80km transmission,0to60°C operatingtemperatureSFP-1GZXLC-T SFP module with11000BaseZX port with LC connector for80km transmission,-40to85°C operatingtemperatureSFP-1GEZXLC SFP module with11000BaseEZX port with LC connector for110km transmission,0to60°C operatingtemperatureSFP-1GEZXLC-120SFP module with11000BaseEZX port with LC connector for120km transmission,0to60°C operatingtemperatureSFP-1G10ALC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for10km transmission;TX1310nm,RX1550nm,0to60°C operating temperatureSFP-1G10ALC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for10km transmission;TX1310nm,RX1550nm,-40to85°C operating temperatureSFP-1G10BLC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for10km transmission;TX1550nm,RX1310nm,0to60°C operating temperatureSFP-1G10BLC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for10km transmission;TX1550nm,RX1310nm,-40to85°C operating temperatureSFP-1G20BLC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for20km transmission;TX1550nm,RX1310nm,0to60°C operating temperatureSFP-1G20ALC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for20km transmission;TX1310nm,RX1550nm,-40to85°C operating temperatureSFP-1G20ALC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for20km transmission;TX1310nm,RX1550nm,0to60°C operating temperatureSFP-1G20BLC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for20km transmission;TX1550nm,RX1310nm,-40to85°C operating temperatureSFP-1G40BLC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for40km transmission;TX1550nm,RX1310nm,0to60°C operating temperatureSFP-1G40BLC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for40km transmission;TX1550nm,RX1310nm,-40to85°C operating temperatureSFP-1G40ALC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for40km transmission;TX1310nm,RX1550nm,0to60°C operating temperatureSFP-1G40ALC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for40km transmission;TX1310nm,RX1550nm,-40to85°C operating temperaturePower SuppliesDR-452445W/2A DIN-rail24VDC power supply with universal85to264VAC or120to370VDC input,-10to50°C operating temperatureDR-75-2475W/3.2A DIN-rail24VDC power supply with universal85to264VAC or120to370VDC input,-10to60°C operating temperatureDR-120-24120W/2.5A DIN-rail24VDC power supply with universal88to132VAC or176to264VAC input byswitch,or248to370VDC input,-10to60°C operating temperatureMDR-40-24DIN-rail24VDC power supply with40W/1.7A,85to264VAC,or120to370VDC input,-20to70°Coperating temperatureMDR-60-24DIN-rail24VDC power supply with60W/2.5A,85to264VAC,or120to370VDC input,-20to70°Coperating temperatureWall-Mounting KitsWK-46-01Wall-mounting kit,2plates,8screws,46x66.8x2mmRack-Mounting KitsRK-4U19-inch rack-mounting kit©Moxa Inc.All rights reserved.Updated Jul10,2023.This document and any portion thereof may not be reproduced or used in any manner whatsoever without the express written permission of Moxa Inc.Product specifications subject to change without notice.Visit our website for the most up-to-date product information.。

各种品牌卫星小锅接收器解密方法大全

各种品牌卫星小锅接收器解密方法大全用遥控器进行自动搜索节目,系统设置的密码是F1 1 1 F2 0 2 其中F1,F2为遥控器上的按键。

菜单－－系统设置－－确定－－F1 1 1 F2 0 2 输入这六位数密码确定－－自动搜索等进度条100%就OK了。

如果不行的话再来一次就没问题了。

一、皇视1、皇视2080：在“转发器设定”时按5160、1698、156988。

2、皇视2080A型冲击波机（V：1.11）；在开机状态下用遥控器按“菜单”键→电视屏显皇视主菜单→键入“530478”，电视机屏显“系统信息，数据存储中……”，待显示消失，在皇视主菜单中出现“自动搜索”，机内电视节目自动恢复为工厂设置。

此时选中“自动搜索”，设置相应参数，即可进行盲扫。

3、皇视HSR-2080A：调出主菜单→进入“转发器设置”一项，直接用遥控器按“1698”→画面出现“系统更新”字样，随后在主菜单“节目编辑”的下一栏出现“自动搜索”，进入该栏，按照相应的参数设置，再按“确认”键即可。

4、皇视HSR-2080C:将光标移至“转发器设定”，用遥控器数字键输入“1698”或“5168”即可。

5、皇视2080/C：菜单→皇视主菜单→转发器设定→5168或235523即可。

6、皇视2080系列设置方法：打开主菜单直接输入“5168”即可恢复。

7、皇视免费机的方法密码530478。

二、东仕8、东仕：（1）在恢复出厂时按“1270”。

（2）恢复出厂确定时按左键→“喜爱”键。

（3）各版本9画面的打开方法：5.13版：右键→ 确认键。

5.60版：改名键→左键→确认键。

5.89版：右键→左键→改名键→确认键。

9、东仕2000Q开启盲扫和9画面设置：按菜单→系统设置→恢复出厂设置→确认恢复（先不要按确认），按音量右键，然后按确认键恢复出厂状态，这时机器恢复到了出厂状态，9画面功能开启：进行第二次的按菜单→系统设置→恢复出厂设置→确认恢复（先不要按确认），按喜爱键，机器再一次恢复到出厂状态，9画面和盲扫都打开了。

博士安全B520辅助电源模块说明书

u为防火或防盗应用提供高达2 A 的12 V 待机电流（4 A 的盗警电流）u分别监测多达两个12 V 7-18 Ah 电池（多达36 Ah 的容量）u 提供多达80个小时的待机时间u 方便读取式开关寻址u使用博世标准TR1850插入式变压器B520辅助电源模块是一个辅助电源扩展设备，可通过SDI2总线连接到兼容的报警主机。

此模块受到监测并将所有状态更改传递给报警主机。

工业、商业和机构设施是B520模块的典型安装。

B520地址开关可用于实现轻松设备寻址。

SDI2输出端子为SDI2扩展设备（如键盘）提供辅助电源。

AUX PWR 端子为其他设备（如PIR 移动探测器）提供增强型辅助电源功能。

功能监测监控此模块通过SDI2总线监控并传送有关以下内容的状态信息：•操作（检测信号）•电池1 (BATT 1)•电池2 (BATT 2)•AC 输入电源(AC)•电池电量充足•电池电量不足•电池缺失指示灯•检测信号 [图标]。

当系统正常运行时，蓝色LED 指示灯闪烁亮起和熄灭。

LED 指示灯持续亮起或熄灭指示系统故障。

闪烁三次指示通信故障。

•BATT 1 LED 指示灯。

LED 指示灯呈绿色持续亮起指示BATT 1的电池状态正常工作。

闪烁指示电池电量不足。

闪烁三次指示电池充电器故障。

LED 指示灯熄灭指示电池缺失。

•BATT 2 LED 指示灯。

LED 指示灯呈绿色持续亮起指示BATT 2的电池状态正常工作。

闪烁指示电池电量不足。

闪烁三次指示电池充电器故障。

LED 指示灯熄灭指示电池缺失。

•AC LED 指示灯。

LED 指示灯呈绿色持续亮起指示AC 电源正在工作。

正在执行电池测试时会产生脉冲式LED 指示灯（每秒3个脉冲）。

闪烁指示AC 电源不足或发生故障。

电池充电在AC 电源发生故障的情况下，连接到电池端子的已充满电的电池将为B520提供电源。

如果B520的AC 电源输入发生故障（缺失或电量低），则B520将自动从主电源(AC)切换到备用电源（电池）。

TP8230_CN_V1.0,隔离不带PFC,三段开关

特点
集成三段式开关调光功能 100%,50%,10% 调光亮度原边反馈恒流控制，无需次级反馈电路准谐振开关模式，开关损耗小 ±3% 的 LED 输出电流精度 LED 输出电流纹波小，无频闪优异的线电压调整率和负载调整率超低启动电流，典型值 20μA LED 输出开路保护 LED 输出短路保护 VCC 供电过压保护 VCC 供电欠压保护自动重启动功能芯片过温保护采用 SOP8L 封装
PCB 布局
TP8230在进行PCB布局时，建议按以下规则进行：
走线
1. 辅助绕组地先与VCC电容地连接，再与芯片地连接。 2. ZCD 、 COMP 等信号地与芯片地连接，走线越短越好。 3. 芯片地与 CS电阻地连接后再与输入电容地连接，且走线越短越好。 4. ZCD为弱信号， ZCD电阻应尽量靠近 ZCD 脚，并远离干扰源。 5. 功率管的漏极为主要干扰源，走线越短越好。 6. VCC电容应尽量紧靠芯片的VCC脚和 GND脚。
其中， TDIS 为变LED 输出平均电流可以表示为：
输出电流设定
在功率管开始导通时，变压器初级绕组电流从零开始斜坡上升，同时 CS 脚的电压也斜坡上升。当 CS 脚电压上升到 CS 峰值控制电压时，功率管关断。变压器初级绕组 V1.0 TP8230 内部进行电流采样和恒流控制，使得：其中， VREF 为输出平均电流基准电压，典型值为 300mV 。 Shenzhen TPOWER Semiconductor 4
LED 短路保护
当 LE D 短路发生时，LE D 输出电压很小，变压器辅助绕组的电压也很小，并不足以对 V CC 进行供电。因此， V CC 电压开始下降，当 V CC 电压下降到芯片的关断电压时， TP8230 欠压锁死。

GL823K Datasheet

GL823KUSB 2.0 SD Card Reader ControllerDatasheetRevision HistoryTable of ContentsCHAPTER 1GENERAL DESCRIPTION (6)CHAPTER 2FEATURES (7)CHAPTER 3PIN ASSIGMENT (8)3.1SSOP16 Pinout (8)3.2Pin Description (9)CHAPTER 4BLOCK DIAGRAM (10)4.1OCCS USB PHY (10)4.2SIE (10)4.3EPFIFO (10)4.4MCU (10)4.5MHE (11)4.6Regulator (11)4.7PMOS (11)CHAPTER 5ELECTRICAL CHARACTERISTICS (12)5.1Temperature Conditions (12)5.2Operating Conditions (12)5.3DC Characteristics (12)5.4Memory Card Clock Frequency (12)5.5Maximum Ratings (13)CHAPTER 6PACKAGE DIMENSION (14)CHAPTER 7ORDERING INFORMATION (15)List of FiguresFigure 3.1 – SSOP 16 Pinout Diagram (8)Figure 6.1 – SSOP 16 Pin Package (150 mil) (14)List of TablesTable 3.1 – Pin Description (9)Table 4.1 – Functional Block Diagram (10)Table 5.1 – Temperature Conditions (12)Table 5.2 – Operating Conditions (12)Table 5.3 – DC Characteristics (12)Table 5.4 – SD/MMC Card Clock Frequency (12)Table 5.5 – Maximum Ratings (13)Table 7.1 – Ordering Information (15)CHAPTER 1GENERAL DESCRIPTIONThe GL823K is a USB 2.0 Single-LUN card reader controller which can support SD/MMC Flash Memory Cards. It supports USB 2.0 high-speed transmission to Secure Digital TM(SD), SDHC, SDXC, miniSD TM, microSD TM(T-Flash), MultiMediaCard TM (MMC), RS MultiMediaCard TM (RS MMC), MMCmicro , HS-MMC and MMCmobile. As a single chip solution for USB 2.0 flash card reader, the GL823K complies with Universal Serial Bus specification rev. 2.0, USB Storage Class Specification ver.1.0, and each flash card interface specification.The GL823K integrates a high speed 8051 microprocessor and a high efficiency hardware engine for the best data transfer performance between USB and flash card interfaces. Its pin assignment design fits to card sockets to provide easier PCB layout. Inside the chip, it integrates 5V to 3.3V regulator, 3.3V to 1.8V regulator and power MOSFETs and it enables the function of on-chip clock source (OCCS) which means no external 12MHz XTAL is needed and that effectively reduces the total BOM cost.The GL823K implements USB disconnect function; it can be used for Mobile cable/ OTG reader/ PC card reader application.CHAPTER 2FEATURES●USB specification compliance-Comply with 480Mbps Universal Serial Bus specification rev. 2.0-Comply with USB Storage Class specification rev. 1.0-Support one device address and up to four endpoints: Control (0)/Bulk Read (1)/Bulk Write (2)/Interrupt (3) ●Integrated USB building blocks-USB2.0 transceiver macro (UTM), Serial Interface Engine (SIE), Build-in power-on reset (POR) and low-voltage detector (LVD)●Embedded 8051 micro-controller-Operate @ 60 MHz clock, 12 clocks per instruction cycle-Embedded mask ROM and internal SRAM●Secure Digital TM (SD) and MultiMediaCard TM (MMC)-Supports SD specification v1.0 / v1.1 / v2.0 / SDHC (Up to 32GB)-Compatible with SDXC (Up to 2TB)-Supports MMC specification v3.x / v4.0 / v4.1 / v4.2-Supports 1 / 4 bit data bus-Compliant with Secure Digital TM v5.0●Support boost mode for SD3.0 for better performance●Support non-SD Card Detect pin, non-MS Insertion/Removal pin design to save BOM cost●Support non-SD Write Protection pin design to save BOM cost●Support LED function to indicate power and access status●On chip clock source and no need of 12MHz Crystal Clock input●On-Chip 5V to 3.3V and 3.3V to 1.8V regulators●On-Chip power MOSFET for supplying flash media card power●Support USB disconnection by memory card unplug or manual switch for Mobile cable/ OTG reader/ PCcard reader application●Available in SSOP16 package (150 mil)CHAPTER 3 PIN ASSIGMENT3.1 SSOP16 Pinout38765214D 0D 2P M O S C M D V S S D 1D 3C L KFigure 3.1 – SSOP 16 Pinout Diagram3.2Pin DescriptionTable 3.1 – Pin DescriptionNotation:Type O OutputI InputB Bi-directionalpu internal pull-up when inputpd internal pull-down when inputP Power / GroundA AnalogCHAPTER 4BLOCK DIAGRAMTable 4.1 – Functional Block Diagram4.1OCCS USB PHYThe USB 2.0 Transceiver Macrocell is the analog circuitry that handles the low level USB protocol and signaling, and shifts the clock domain of the data from the USB 2.0 rate to one that is compatible with the general logic. On chip clock source and no need of 12MHz Crystal Clock input.4.2SIEThe Serial Interface Engine, which contains the USB PID and address recognition logic, and other sequencing and state machine logic to handle USB packets and transactions.4.3EPFIFOEndpoint FIFO includes Control FIFO (FIFO0) and Bulk In/Out FIFO●EP0 FIFO FIFO of control endpoint 0. It is 64-byte FIFO and used for endpoint 0 data transfer.●Interrupt FIFO 64-byte depth FIFO of endpoint 3 for status interrupt●Bulk FIFO It can be in the TX mode or RX mode:1. It contains ping-pong FIFO (512 bytes each bank) for transmit/receive data continuously.2. It can be directly accessed by micro-controller4.4MCU8051 micro-controller inside.●8051 Core Compliant with Intel 8051 high speed micro-controller●ROM FW code on ROM●SRAM Internal RAM area for MCU access4.5MHE●MIF Media Interface: SD/MMC●MCFIFO It can access by MCU for memory card short data packet.4.6Regulator●5V to 3.3V Band Gap Regulator for stable voltage supply for USB PHY, PMOS●3.3V to 1.8V For core logic and internal memory.4.7PMOSOn-Chip power MOSFETs for memory card powerCHAPTER 5ELECTRICAL CHARACTERISTICS 5.1Temperature ConditionsTable 5.1 – Temperature Conditions5.2Operating ConditionsTable 5.2 – Operating Conditions5.3DC CharacteristicsTable 5.3 – DC Characteristics5.4Memory Card Clock FrequencyTable 5.4 – SD/MMC Card Clock Frequency5.5Maximum RatingsTable 5.5 – Maximum RatingsCHAPTER 6PACKAGE DIMENSIONInternalNo.Lot CodeDateGL823KAAAAAAAAAAYWWXXXXVersionNo.Figure 6.1 – SSOP 16 Pin Package (150 mil)CHAPTER 7ORDERING INFORMATIONTable 7.1 – Ordering Information。

罗克韦尔自动化 Trusted T8200 高可靠电源系统使用手册说明书

PD_T8200 Trusted Trusted High Integrity Power Supply System (110-240 Vac and 24 Vdc)Product OverviewThe Trusted® power supply assembly converts redundant main line voltages of either 110 Vac / 240 Vac or 24 Vdc, to +15 Vdc or +24 Vdc output power for system and field power requirements.Features:•Redundant power inputs.•250 W.•Hot replaceable.•Current sharing.•Power factor correction.•Front panel indicators for input, output voltage status and output current level on each module.•External status signals.•TϋV Certified IEC 61508 SIL 3.Trusted PD_T8200Page intentionally left blankPREFACEIn no event will Rockwell Automation be responsible or liable for indirect or consequential damages resulting from the use or application of this equipment. The examples given in this manual are included solely for illustrative purposes. Because of the many variables and requirements related to any particular installation, Rockwell Automation does not assume responsibility or reliability for actual use based on the examples and diagrams.No patent liability is assumed by Rockwell Automation, with respect to use of information, circuits, equipment, or software described in this manual.All trademarks are acknowledged.DISCLAIMERIt is not intended that the information in this publication covers every possible detail about the construction, operation, or maintenance of a control system installation. You should also refer to your own local (or supplied) system safety manual, installation and operator/maintenance manuals. REVISION AND UPDATING POLICYThis document is based on information available at the time of its publication. The document contents are subject to change from time to time. The latest versions of the manuals are available at the Rockwell Automation Literature Library under "Product Information" information "Critical Process Control & Safety Systems".TRUSTED RELEASEThis technical manual applies to Trusted Release: 3.6.1.LATEST PRODUCT INFORMATIONFor the latest information about this product review the Product Notifications and Technical Notes issued by technical support. Product Notifications and product support are available at the Rockwell Automation Support Centre atAt the Search Knowledgebase tab select the option "By Product" then scroll down and select the Trusted product.Some of the Answer ID’s in the Knowledge Base require a TechConnect Support Contract. For more information about TechConnect Support Contract Access Level and Features please click on the following link:https:///app/answers/detail/a_id/50871This will get you to the login page where you must enter your login details.IMPORTANT A login is required to access the link. If you do not have an account then you can create one using the "Sign Up" link at the top right of the web page.DOCUMENTATION FEEDBACKYour comments help us to write better user documentation. If you discover an error, or have a suggestion on how to make this publication better, send your comment to our technical support group at SCOPEThis manual specifies the maintenance requirements and describes the procedures to assist troubleshooting and maintenance of a Trusted system. WHO SHOULD USE THIS MANUALThis manual is for plant maintenance personnel who are experienced in the operation and maintenance of electronic equipment and are trained to work with safety systems. SYMBOLSIn this manual we will use these notices to tell you about safety considerations.SHOCK HAZARD: Identifies an electrical shock hazard. If a warning label is fitted, it can be on or inside the equipment.WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous environment, which can cause injury or death, property damage or economic loss.ATTENTION: Identifies information about practices or circumstances that can cause injury or death.CAUTION: Identifies information about practices or circumstances that can cause property damage or economic loss.BURN HAZARD: Identifies where a surface can reach dangerous temperatures. If a warning label is fitted, it can be on or inside the equipment.This symbol identifies items which must be thought about and put in place when designing and assembling a Trusted controller for use in a Safety Instrumented Function (SIF). It appears extensively in the Trusted Safety Manual.IMPORTANT Identifies information that is critical for successful application and understanding of the product.NOTE Provides key information about the product or service.TIP Tips give helpful information about using or setting up the equipment.WARNINGS AND CAUTIONSWARNING: EXPLOSION RISKDo not connect or disconnect equipment while the circuit is live or unless the area is known to be free of ignitable concentrations or equivalentAVERTISSEMENT - RISQUE D’EXPLOSIONNe pas connecter ou déconnecter l’équipement alors qu’il est sous tension, sauf si l’environnement est exempt de concentrations inflammables ou équivalenteMAINTENANCEMaintenance must be carried out only by qualified personnel. Failure to follow these instructions may result in personal injury.CAUTION: RADIO FREQUENCY INTERFERENCEMost electronic equipment is influenced by Radio Frequency Interference. Caution should be exercised with regard to the use of portable communications equipment around such equipment. Signs should be posted in the vicinity of the equipment cautioning against the use of portable communications equipment.CAUTION:The module PCBs contains static sensitive components. Static handling precautions must be observed. DO NOT touch exposed connector pins or attempt to dismantle a module.ISSUE RECORDIssue Date Comments8 Sep 05 Format9 Mar 06 Removed hidden characters10 Sep 15 Rebranded and reformatted11 Apr 16 Standardisation of Operating Temperature and Relative Humidity RangeStatements in the Specification sectionPage intentionally left blankTrusted High Integrity Power Supply System Table of Contents Table of Contents1.Description (3)1.1. Power Supply Chassis (3)1.2. Power Supply Modules (4)1.3. Input Power Regulation (4)1.4. Front Panel Indicators (7)1.4.1. Input Power Voltage Indicator (7)1.4.2. Output Power Display (7)1.4.3. Output Power Indicator (7)2.Installation (9)2.1. Chassis Mounting (9)2.2.Backplane Versions and Module Keying (10)2.2.1. Input Power Terminals: TB1, TB2 (#8 Screw Terminals) (10)2.2.2. Output Power Terminals: TB3, TB4 (#6 Screw Terminals) (11)2.2.3. Status Connectors: J14, J15 (11)2.2.4. Monitor Connector: J13 (12)3.Configuration (13)3.1. Current Sharing (13)3.2. REGENT Power Supply Load Units (13)3.3. Regent I/O Triplicated Power Distribution (13)4.Maintenance (15)5.Specifications (17)Table of Contents Trusted High Integrity Power Supply SystemPage intentionally left blank1.DescriptionThe Power Supply Assembly consists of a Power Supply Chassis containing up to six Power Supply Modules. The Chassis may be configured to distribute power in various combinations. For example, a Chassis containing six Power Supply Modules may be set up with three Modules providing triplicated power for Regent+Plus Input/Output (I/O) assemblies and three Modules providing field power in a N+1 configuration. Alternatively, the Chassis may be set up to provide separate dual 24 Vdc supplies for both a Trusted System and associated field devices.Figure 1 Power Supply Assembly1.1.Power Supply ChassisThe Power Supply Chassis houses a maximum of six Power Supply Modules. It may be mounted in a 19-inch rack or flush mounted on a panel. Table 1 identifies the available types of Chassis.Catalogue No. Chassis Unit Input Power Voltage Configuration T8200 I/O Power Supply Chassis 110-240 Vac, 50/60 Hz Straight BussedT8201 I/O Power Supply Chassis 110-240 Vac, 50/60 Hz Cross BussedT8202 I/O Power Supply Chassis 24 VdcTable 1 Chassis Types1.2.Power Supply ModulesThe Power Supply Assembly Modules are single (if redundant inputs are not required) and dual input, hot swap, user-replaceable ac and dc units. Table 2 identifies the available types of Modules.Catalogue No. Input Type Input Power Voltage Output Power Voltage T8220 Dual 110-240 Vac 15 VdcT8222 Dual 24 Vdc 15 VdcT8223 Single 110-240 Vac 24 VdcT8224 Single 110-240 Vac 15 VdcT8225 Dual 110-240 Vac 24 VdcT8226 Dual 24 Vdc 24 VdcTable 2 Module TypesThe dual inputs on the ac Modules are galvanically isolated from each other. The inputs on the dc Modules are diode isolated and share a common return.1.3.Input Power RegulationA block diagram of a typical dual ac input I/O Power Supply Module is shown in Figure 2. A block diagram of a typical dual dc input I/O Power Supply Module is shown in Figure 3. ArrayFigure 2 Block Diagram of a Dual ac I/O Power Supply ModuleFigure 3 Block Diagram of a Dual dc I/O Power Supply ModuleEach primary power input is individually fused and filtered with both standard line filters and metal oxide varistors (MOVs). The filters attenuate any high frequency common mode and normal mode noise present in the power distribution system. The MOVs clamp high voltage transients.Filter, rectifier, and power factor correction circuits convert primary ac input power to bulk dc voltage. The switching regulator converts bulk dc power to regulated dc output voltage. Sensing, status, control and timing circuits provide for the following:•Input power failure - Active low status output. Indicates when the input voltage is below 85 Vac or 18 Vdc. There is a separate signal for each input.•Bulk power failure - Active high status output on ac input modules only. Indicates the dc bulk voltage (power factor correction (PFC output)) is outside the specifiedrange. There is a separate signal for each input.•High temperature warning alarm - Both an active high and active low status output are provided. Indicates when the module temperature exceeds 75 °C. Thetemperature is sensed near the air inlet (bottom) of the module.•High temperature shutdown - Internal signal that will shut down the switching regulator if module temperature is above 85 °C. The temperature is sensed near the air inlet (bottom) of the module.•Output over-voltage - Internal signal that will shut down the switching regulator if the output voltage exceeds +18 Vdc for the 15 volt module and +28 Vdc for the24 volt module. Over-voltage protection circuitry activation is a permanent errorcondition, requiring manual intervention to return module to normal operation.•dc output fail - Active high status output indicates the dc output voltage has gone out of regulation. The dc output fail threshold is 13.75 Vdc (±0.25 Vdc) for the 15 volt module, and 21.75 Vdc (±0.25 Vdc) for the 24 volt module.•Output current limiting - Internal signal limits output current in excessive current demand situations.•POWER FAIL - Active high status signal that indicates impending loss of output power due to one of the following:o Both inputs have indicated power failure.o Remote off control signal activated.o Thermal shutdown.o Output over-voltage.•RESET - Active high status signal that is generated a minimum of 10 ms (ac input module) or 0.5 ms (dc input module) after a POWER FAIL signal. RESET remainsasserted for 200 ms (minimum) after module power-up.•PFC off - Active low input that turns off the power factor correction of an individual input. This signal provides the capability to test the input circuitry of a module byturning off each input independently while monitoring the module fail signal.•Remote off - Active low input that turns off the output power of a module.Note: Bulk Power Fail, PFC Off and Remote Off are accessed through the Monitor Module Connector on the chassis backplane. The Monitor Module Connector allows for a future development of a monitor card that would provide remote control and enhanced monitoring of the Power Supply Chassis.Active low signals are not maintained while RESET is active. All status signals are open collector and require external pull-up resistors.RESET is used in the Regent I/O Transceivers for power system interlocking within the I/O system. A power failure (either input power or module fault) activates RESET and turns off the dc output Front Panel Indicator.The POWER FAIL and RESET signals are required for proper operation of Regent I/O Transceivers and I/O modules during power-up, power down, and loss of power. Refer to Assembly Installation in the associated Regent Product Description for details of connecting these signals to a Regent I/O Chassis.1.4.Front Panel IndicatorsThe Front Panel of each I/O Power Supply Module supports three Light Emitting Diode (LED) indicators detailed in the following sub-paragraphs1.4.1.Input Power Voltage IndicatorEach green INPUT POWER indicator is lit when the associated input (Input A, Input B) is above the lower input voltage threshold.1.4.2.Output Power DisplayThe 10-segment LED indicator bar displays the approximate output current level percentage(0 % - 100 %)1.4.3.Output Power IndicatorThe DC Output indicator is lit when the I/O Power Supply Module's dc output is within tolerance. Out-of-tolerance conditions, loss of input power or brown-out, and module failures turn off this indicator.Page intentionally left blank2.Installation2.1.Chassis MountingFigure 4 and Figure 5 show the front and rear views of the Power Supply Chassis.Figure 4 Power Supply Chassis Front ViewFigure 5 Power Supply Chassis Rear ViewMounting flanges can be attached to either the rear or the front of the Chassis. This allows flush mounting the Chassis to a panel or mounting in a 19-inch rack. The Input Crossover Patch is on the T8200 chassis only.2.2. Backplane Versions and Module KeyingConnector placement on ac Input Modules and backplanes differ from dc modules and backplanes. This prohibits insertion of the wrong Input Module type into a backplane. Module slots in a chassis can be individually keyed to only accept a Module of a particular output voltage.2.2.1. Input Power Terminals: TB1, TB2 (#8 Screw Terminals)Terminal No.T8200 T8202 Source 1 N DC- B 2 L DC+ 3 N DC- A 4LDC+Table 3 Input Power Terminals6E6 6E5 6E7 6E86E3 6E4 6E16E22.2.2. Output Power Terminals: TB3, TB4 (#6 Screw Terminals)Terminal No.Module SlotT8200, T820212 6 + DC Output 11 5 10 4 9 3 8 2 7 1 6 5 4 1-6 DC Return (terminals 1-6 are connected together onBackplane)3 2 1Table 4 Output Power Terminals2.2.3. Status Connectors: J14, J15• Type: 10 pin shrouded header, double row, 0.100 x 0.100 Centres • Manufacturer:AMP• Manufacturer Part No: 102618-3 • Mating Connector: AMP 87631-5• Pin Out:Pin J14J15Slot Signal Slot Signal 1 2 All Input ‘A’ Fail 3AllInput ‘B’ FailPin J14 J15Slot Signal Slot Signal4 All Hi Temperature5 1 Reset 4 Reset6 1 Power Fail 6 Reset7 2 Reset 4 Power Fail8 3 Power Fail 6 Power Fail9 2 Power Fail 5 Power Fail10 3 Reset 5 ResetTable 5 Status Connectors2.2.4.Monitor Connector: J13•Type: 72 pin Edge Connector, 0.125 in centreline •Manufacture: AMP•Manufacturer Part No: 1-530844-9•Pin-out: Not Configured3.Configuration3.1.Current SharingThe Modules are capable of current sharing by connecting their outputs together in parallel. This can be done external to the Chassis or by using a shorting bar that mounts directly to the output terminals on the Chassis backplane. This allows separate groups of Modules from within a single Chassis to have their outputs configured as Single, Dual or N+1. The Module uses a passive ‘droop’ method of current sharing and will share to within 25 % of the rated load.3.2.REGENT Power Supply Load UnitsWhen using the Power Supply System with Regent and Regent+Plus , power supply loading is based on the number of I/O Modules in the I/O Chassis and the load imposed by each I/O Module. Load units for each I/O Module are shown in that Module’s product description and specification sheet under the Safetybus Power heading. A set of three Power Supply Modules will provide the following load units:Number of I/O Units (Chassis): 1 2 3 4Load Unit Capacity: 82 78 74 70Table 6 Available Load Units (for a set of three power supplies) Calculating the number of load units in the system helps determine the number of I/O Power Supplies required by the system. For economic power distribution, and to avoid overloading individual Power Supply Units, calculate power supply loading when configuring systems.3.3.Regent I/O Triplicated Power DistributionA Chassis can contain two sets of triple-redundant Power supplies for Regent I/O. Each of the triple-redundant I/O Power Supply Modules within the I/O Power Supply Chassis provides power for one leg of the three redundant legs of the I/O Safetybus Transceivers, and provides power to all the I/O Modules within its associated I/O Chassis. Each I/O Module contains a diode OR power-sharing circuit that receives power from all three I/O Power Supply Modules.Should any I/O Power Supply Module fail, only one leg of the transceiver modules loses power: the two remaining legs maintain proper Regent operation. In addition, all the I/O Modules continue to operate properly by drawing their current from the two remaining Power Supplies within the I/O Power supply assembly.I/O Transceivers and I/O Modules require power fail and reset status signals for proper operation.4.MaintenanceNo periodic maintenance or calibration is required for I/O Power Supply Modules. There are no user-replaceable parts.A failed I/O Power Supply Module can be hot-replaced without disrupting system operations. Main power wiring and I/O power cables (connected to the Chassis) are not disturbed during Module replacement.Page intentionally left blank5.SpecificationsVoltage RangeT8220, T8223, T8224, T8225 85 Vac to 264 VacT8222, T8226 20 Vdc to 32 VdcFrequency RangeT8220, T8223, T8224, T8225 47 Hz to 63 HzInrush Current (120/260 Vac)T8220, T8223, T8224, T8225 20/4 0A (peak) Cold, 35/65 A (peak)HotPower Factor 0.95 min.Efficiency 70 %Use with ChassisT8220, T8223, T8224, T8225 T8200T8222, T8226 T8202Fusing (Internal to module)T8220, T8223, T8224, T8225 6 A, 250 V, 3AG Slow BlowT8222, T8226 20 A, 250 V, 3AB Slow Blow Output VoltageT8220, T8222, T8224 +15 VdcT8223, T8225, T8226 +24 VdcOutput Power 250 W, per modulePower Hold-up TimeT8220, T8223, T8224, T8225 20 ms, minimumT8222, T8226 1 ms, minimumOperating Temperature 0 °C to +60 °C (+32 °F to +140 °F)Non-operating Temperature -25 °C to +70 °C (-25 °F to +158 °F) Relative Humidity range(operating, storage & transport) 10 % – 95 %, non-condensing Environmental Specifications Refer to document 552517 Module DimensionsHeight 266 mm (10.47 in)Width 61 mm (2.38 in)Depth 318 mm (2.5 in)Chassis DimensionsHeight 266 mm (10.47 in)Width 483 mm (19 in)Depth 343 mm (13.5 in)Module Weight 3.25 kg (7.2 lb)Chassis Weight 7 kg (15.4 lb)。

AES 1235 品牌 BNS 产品名称磁性安全传感器型号 101170049说明书

DATASHEETDataOrdering dataNote (Delivery capacity)Phased-out product Product type description AES 1235101170049Article number (ordernumber)EAN (European Article4030661297118 Number)27-37-18-19eCl@ss number, version12.027-37-18-19eCl@ss number, version11.027-37-18-19eCl@ss number, version9.0EC001449ETIM number, version7.0EC001449ETIM number, version6.0Available until31.12.2023Approvals - StandardsCertificates BGcULusGeneral dataStandards BG-GS-ET-14BG-GS-ET-20EN IEC 62061EN ISO 13849-1EN IEC 60947-5-1EN IEC 60947-5-3EN IEC 60947-5-5EN IEC 60204-1EN IEC 60947-1Climatic stress EN 60068-2-3BG-GS-ET-14Enclosure material Glass-fibre reinforced thermoplastic, ventilated Gross weight240 gGeneral data - FeaturesStop-Category0Wire breakageYesdetectionCross-circuit detection YesFeedback circuit YesYesAutomatic resetfunctionReset afterYesdisconnection of supplyvoltageEarth connectionYesdetectionYesIntegral systemdiagnostics, statusNumber of LEDs12Number of normallyclosed (NC)1Number of normallyopen (NO)Number of undelayed2semi-conductor outputswith signaling functionNumber of safety2contactsNumber of signalling2outputsSafety classificationStandards EN ISO 13849-1EN IEC 61508Safety classification - Relay outputsdPerformance Level, uptoCategory3PFH value 1.00 x 10⁻⁷ /hNotice for max. 50,000 switching cycles/year and max. 80% contact load2Safety Integrity Level(SIL), suitable forapplications inMission time20 Year(s)Mechanical data20,000,000 OperationsMechanical life,minimumMounting Snaps onto standard DIN rail to EN 60715Mechanical data - Connection techniqueTerminal designations IEC/EN 60947-1Termination rigid or flexibleScrew terminals M20 x 1.5Cable section, minimum0.25 mm²2.5 mm²Cable section,maximumTightening torque of0.6 NmClipsMechanical data - DimensionsWidth22.5 mmHeight100 mmDepth121 mmAmbient conditionsDegree of protection ofIP40the enclosureDegree of protection ofIP54the mounting spaceDegree of protection ofIP20clips or terminalsAmbient temperature+0 ... +55 °CStorage and transport-25 °Ctemperature, minimumStorage and transport+70 °Ctemperature, maximumResistance to vibrations10...55 Hz, Amplitude 0.35 mm, ± 15 % Restistance to shock30 g / 11 msAmbient conditions - Insulation valuesRated impulse4 kVwithstand voltage UimpOvervoltage category IIIDegree of pollution2Electrical dataFrequency range50 Hz60 HzOperating voltage24 VAC -15 % / +10 %24 VDC -10 % / +20 %Ripple voltage10 %Thermal test current 6 ARated operating voltage24 VACRated operating voltage24 VDC20.4 VACRated AC voltage forcontrols, 50 Hz,minimum26.4 VACRated control voltage atAC 50 Hz, maximum20.4 VACRated AC voltage forcontrols, 60 Hz,minimum26.4 VACRated control voltage atAC 60 Hz, maximum20.4 VDCRated AC voltage forcontrols at DC minimumRated control voltage at28.8 VDCDC, maximum5 WElectrical powerconsumption0.1 ΩContact resistance,maximumin new stateNote (Contactresistance)Drop-out delay in case80 msof power failure,typically20 msDrop-out delay in caseof emergency, typically100 msPull-in delay atautomatic start,maximum, typically20 msPull-in delay at RESET,typicallyMaterial of the contacts,Ag-Ni 10 and 0.2 µm gold-plated electricalElectrical data - Safe relay outputsVoltage, Utilisation230 VACcategory AC-156 ACurrent, Utilisationcategory AC-15Voltage, Utilisation24 VDCcategory DC-136 ACurrent, Utilisationcategory DC-13Switching capacity,10 VDCminimum10 mASwitching capacity,minimum250 VACSwitching capacity,maximum8 ASwitching capacity,maximumElectrical data - Digital inputs10 … 30 VDCInput signal, HIGHSignal "1"0 … 2 VDCInput signal, LOW Signal"0"40 ΩConduction resistance,maximumElectrical data - Digital OutputVoltage, Utilisation24 VDCcategory DC-120.1 ACurrent, Utilisationcategory DC-12Electrical data - Relay outputs (auxiliary contacts) Switching capacity,24 VDCmaximumSwitching capacity,2 AmaximumElectrical data - Electromagnetic compatibility (EMC)EMC rating EMC-DirectiveIntegral system diagnosis (ISD)Note (ISD -Faults)The following faults are registered by the safety monitoring modules and indicated by ISD.Faults Failure of the safety relay to pull-in or drop-outFailure of door contacts to open or closeCross-wire or short-circuit monitoring of the switch connectionsInterruption of the switch connectionsFault on the input circuits or the relay control circuits of the safety monitoring moduleOther dataNote (applications)Safety sensorGuard systemNoteNote (General)Inductive loads (e.g. contactors, relays, etc.) are to be suppressed by means of asuitable circuit.Wiring exampleNote (Wiring diagram)The wiring diagram is shown with guard doors closed and in de-energised condition.To secure a guard door up to PL d and Category 3Monitoring 1 guard door(s), each with a magnetic safety sensor of the BNS rangeThe ISD tables (Intergral System Diagnostics) for analysis of the fault indications andtheir causes are shown in the appendix.Expansion of enable delay time: The enable delay time can be increased from 0.1 s to1 s by changing the position of a jumper link connection under the cover of the unit.The feedback circuit monitors the position of the contactors K3 and K4.Start push button: A start push button (NO) can optionally be connected into thefeedback circuit. With the guard door closed, the enabling paths are then not closeduntil the start push button has been operated.If only one external relay or contactor is used to switch the load, the system can beclassified in Control Category 3 to ISO 13849-1, if exclusion of the fault “Failure of theexternal contactor” can be substantiated and is documented, e.g. by using a reliabledown-rated contactor. A second contactor leads to an increase in the level of securityby redundant switching to switch the load off.If neither start button nor feedback circuit are connected, a jumper connection must bemounted between X1 and A1.Modification for 2 NC contacts: The safety monitoring module can be modified tomonitor two NC contacts by bridging the terminals A1 and X2. In this configuration, theshort-circuit detection becomes inoperative.Ordering codeProduct type description:AES 123(1)(1)56without start-up test6with start-up testDocumentsOperating instructions and Declaration of conformityAES 1235 / AES 1236(245.3 kB, 10.05.2019, Revision D)BG-test certificateAES and BNS - BG-GS-ET-14 - AES 1135 / AES 1136 / AES 1145 / AES 1146 / AES 1155 / AES 1156 / AES 1165 / AES 1166 / AES 1175 / AES 1176 / AES 1235 / AES 1236 / AES 1265 / AES 1266 / AES 1185(1.4 MB, 10.05.2019, Revision F)BG-test certificateAES - BG-GS-ET-20 - AES 1135 / AES 1136 / AES 1145 / AES 1146 / AES 1155 / AES 1156 / AES 1165 / AES 1166 / AES 1175 / AES 1176 / AES 1235 / AES 1236 / AES 1265 / AES 1266(738.9 kB, 10.05.2019, Revision D)UL CertificateAES / FWS / BNS / BN(415.3 kB, 01.08.2019)Wiring example (electr. wiring)AES 123x(19.6 kB, 10.05.2019)Wiring example (electr. wiring)AES 123x(19.7 kB, 10.05.2019)InfoAES 1135 / AES 1136 / AES 1165 / AES 1166 / AES 1185 / AES 1235 / AES 1236(34.3 kB, 30.06.2021)SISTEMA-VDMA library(659.5 kB, 23.03.2023)PicturesProduct picture (catalogue individual photo)ID: kaes1f09| 711.0 kB | .jpg | 265.642 x 529.167 mm - 753 x 1500 px - 72 dpi| 84.7 kB | .png | 74.083 x 147.461 mm - 210 x 418 px - 72 dpiWiring exampleID: maes1l11| 34.0 kB | .cdr || 143.8 kB | .jpg | 352.778 x 408.517 mm - 1000 x 1158 px - 72 dpiWiring exampleID: kaes1l41| 34.1 kB | .cdr || 139.5 kB | .jpg | 352.425 x 396.875 mm - 999 x 1125 px - 72 dpiK.A. Schmersal GmbH & Co. KG, Möddinghofe 30, 42279 WuppertalThe details and data referred to have been carefully checked. Images may diverge from original. Further technical data can be found in the manual. Technical amendments and errors possible.Generated on: 27/07/2023, 01:44。

si823x中文数据手册

Si823x
0.5 和 4.0 安培 I S O D R I V E R （ 2. 5 和 5
特性

KVRMS）
一个封装内两个完全隔离的驱动 60 ns 传送延时（最大）器独立 HS 和 LS 输入或 PWM 输入最高 5 kVRMS 输入到输出隔离版本最高 1500 VDC 峰值驱动器到驱动瞬态抑制 >45 kV/µs
宽体 SOIC-16 窄体 LGA-14
SOIC-16
应用
供电系统电机控制系统直流到直流隔离供电

照明控制系统等离子显示器太阳能和工业变换器

安全认证

UL 1577 认证
1

VDE 认证合规
60747-5-5 （VDE 0884 第 5 部分） EN 60950-1 （强化绝缘）
IEC
分钟内最多 5000 Vrms
CSA component notice 5A 认证
IEC
60950-1, 61010-1, 60601-1 CQC 认证（强化绝缘） GB4943.1
描述
Si823x 隔离驱动器系列将两个独立、隔离的驱动器集成到一个封装内。 Si8230/1/3/4 是高侧 / 低侧驱动器，而 Si8232/5/6/7/8 是双驱动器。还提供峰值输出电流 0.5 A (Si8230/1/2/7) 和 4.0 A (Si8233/4/5/6/8) 的版本。所有驱动器的最大供电电压为 24 V。 Si823x 驱动器采用 Silicon Labs 自主研发的硅隔离技术，提供符合 UL1577 的 5 kVRMS 耐受电压以及 60 ns 快速传送时间。驱动器输出可连接到相同或独立的地线进行接地，或者连接到正或负电压。单个控制输入 (Si8230/2/3/5/6/7/8) 或 PWM 输入 (Si8231/4) 配置提供滞后 >400 mV 的 TTL 级兼容输入。高度的集成、低传送延时、较小的外形及其灵活性和成本效益性使 Si823x 系列非常适合 MOSFET/IGBT 门驱动器隔离应用。

DPtech FW1000系列应用防火墙安装手册v2.01

iv
DPtech FW1000 系列应用防火墙安装手册
2.2.4 抗干扰要求............................................................................................................................... 3 2.2.5 防雷击要求............................................................................................................................... 3 2.2.6 接地要求................................................................................................................................... 3 2.2.7 布线要求................................................................................................................................... 3 2.3 安装工具......................................................................................................................................4
杭州迪普科技有限公司为客户提供全方位的技术支持。通过杭州迪普科技有限公司代理商购买产品的用户，请直接与销售代理商联系；直接向杭州迪普科技有限公司购买产品的用户，可直接与公司联系。

POWER832 用户手册

关于你的系统你所使用的DSC Power832安全系统的为你提供最具灵活性和方便性的设计，请仔细阅读这本使用手册，和请安装人员介绍这个系统的特性。

你的安全系统是由DSC Power832控制箱，一个或多个Power832键盘和不同探测器组成，控制箱安装在隐蔽的地方，金属的铁箱内含系统电路板，保险丝、电池和变压器等。

除了安装服务公司，其它人员是不能触动该控制箱的。

所有的键盘都有一个音频提示。

LED 的键盘有一组区域灯和系统状态灯，LCD 键盘有阿拉伯字母液晶显示。

键盘是用于向系统发出命令和显示当前系统状态，键盘要安装在一个受到保护且靠近门口的地方。

这个安全系统有数个受保护的防区，每个防区连接一个或多个探测器，在报警时相应的LED 灯会闪亮或在LCD 键盘上显示报警的信息。

联系密码联系密码是用于开启和关闭报警系统，系统共有32个联系密码，其中一个主人密码和32个用户密码。

只有主人密码可以用于编程、增加安全密码和改变其它的系统特性，主人密码由安装公司提供。

开启系统从LED 键盘开启系统如果Ready 灯亮，表示系统已准备好，可以开启，如果Ready 灯不亮，系统是不能启动的。

这时候，你必须检查所有的门、窗是否已关好，并且在有移动探测器的范围内停止走动。

输入你的联系密码，当每按一个键，键盘将会发出“嘀”的一声，如果输入的联系密码不正确，键盘将会发出两秒连续的“嘀”声。

如果发生这样的情况，请按[#]再重新输入你的联系密码，如果输入正确的联系密码，键盘发出快速的嘀嘀声，并且Armed 灯亮，这时你可以从允许的门退出。

从LCD 键盘启动当这个信息出现，表示一个或多个区域是没有关闭的。

关闭门和窗，停止在活动探测器范围内活动。

当这个信息出现时，用箭头（<>）键以确定系统的故障情况，同时检查可能有一些区域被无意让路。

这个信息出现时，系统处于准备状态，可以开启。

开启系统请输入联系密码。

一旦正确的联系密码输入，显示如图所示，控制箱提供一个退出延时，键盘发出“嘀嘀”声提示，你可以指定的通道退出。

ThinkPad(IBM)ThinkPad Z61系列说明书

Access Help G;>Z]j!D*zVa,CVaIbpzTFczDs`}IJ,o zzdC$0&\?~M$_,r_-zbvJb#*r* Access Help, k%w*<,+8kFAyPLr(Z} Windows XP bD Windows® P,FALr),;sFA ThinkVantage#%w Access Help#
62+k#^8O7 |(;c2+5wMj{D0Lenovo P^#$yw1#
u}yw >ywD=<#kZ9C ThinkPad FczD^_&\0DA#ThinkPad Z61 5P Fcz{ONNQz<JmT^_==9C|GDzRrXxF )Dd5M2+j<#kOq4U1Xd5\mu}20M9C ThinkPad Fcz#
|P#
© Copyright Lenovo 2006
3
#x ThinkPad Fcz
}79Cf"iJM}/w v &\bc1ekmL"ZmLOy`Ej)r_3yj);NL,Tbj)(
Z}/wP# v g{Fcz=xng CD"DVD r CD-RW/DVD HbL}/w,k;*%~
bLDmfrPLOD$b7# v H=}{ CD r DVD G*;yEkng CD"DVD r CD-RW/DVD HbL
gSzdvyw . . . . . . . . . . 76 gSxdyw. . . . . . . . . . . . 76
*n(E/1a(FCC)yw . . . . . 76 SCs$5? B `xdf6{Oyw. . . 77 Avis de conformité à la réglementation d’Industrie Canada . . . . . . . . . 77 7K EMC 8n;BTyw . . . . . . 77 U>D73yw . . . . . . . . . . . 77 7^8n 2002/96/EC DX*E" . . . . . 79 Lj. . . . . . . . . . . . . . . 79

摩萨 EDS-4012 系列 8+4G 端口（带 8 802.3bt PoE 端口选项）管理网关交换

EDS-4012Series8+4G-port (with 8802.3bt PoE port option)managed Ethernet switchesFeatures and Benefits•Developed according to the IEC 62443-4-1and compliant with the IEC62443-4-2industrial cybersecurity standards•Support for IEEE 802.3bt PoE for up to 90W output per port•Turbo Ring and Turbo Chain (recovery time <20ms @250switches)1,andRSTP/STP for network redundancy•Wide range of power input options for flexible deployment •Compact and flexible housing design to fit into confined spaces •Supports MXstudio for easy,visualized industrial network managementCertificationsIntroductionThe EDS-4012Series is a range of 12-port managed Fast Ethernet switches with the option for four 1Gbps fiber-optic uplink ports.This Series also offers models with four 10/100BaseT(X)802.3af (PoE),802.3at (PoE+),and 802.3bt-compliant Ethernet PoE port options to connect high-bandwidth PoE devices.Redundant Ethernet technologies such as Turbo Ring,Turbo Chain,and RSTP/STP increase the reliability of your system and improve the availability of your network backbone.The EDS-4012Series is designed specifically for demanding applications such as video and process monitoring,ITS,and DCS systems,all of which can benefit from a scalable backbone.The EDS-4012Series is compliant with the IEC 62443-4-2and IEC 62443-4-1Industrial Cybersecurity certifications,which cover both product security and secure development life-cycle requirements,helping our customers meet the compliance requirements of secure industrial network design.SpecificationsEthernet Interface10/100BaseT(X)Ports (RJ45connector)EDS-4012-4GS-LV/-HV/-T models:8EDS-4012-4GC-LV/-HV/-T models:8Auto negotiation speed Full/Half duplex modeAuto MDI/MDI-X connectionPoE Ports (10/100BaseT(X),RJ45connector)EDS-4012-8P-4GS-LVA/-LVB/-T models:8100/1000BaseSFP PortsEDS-4012-4GS-LV/-HV/-T models:4EDS-4012-8P-4GS-LVA/-VB/-T models:41.If the port link speed is 1Gigabit or higher,the recovery time is <50ms.Combo Ports(10/100/1000BaseT(X)or100/EDS-4012-4GC-LV/-HV/-T models:41000BaseSFP)Standards IEEE802.3for10BaseTIEEE802.3u for100BaseT(X)and100BaseFXIEEE802.3ab for1000BaseT(X)IEEE802.3z for1000BaseXIEEE802.3x for flow controlIEEE802.3ad for Port Trunk with LACPIEEE802.1Q for VLAN TaggingIEEE802.1D-2004for Spanning Tree ProtocolIEEE802.1w for Rapid Spanning Tree ProtocolIEEE802.1p for Class of ServiceIEEE802.1X for authenticationEthernet Software FeaturesFilter GMRP,GVRP,GARP,802.1Q VLAN,IGMP Snooping v1/v2/v3,IGMP QuerierManagement IPv4/IPv6,Flow control,Back Pressure Flow Control,DHCP Server/Client,ARP,RARP,LLDP,Port Mirror,Linkup Delay,SMTP,SNMP Trap,SNMP Inform,SNMPv1/v2c/v3,RMON,TFTP,SFTP,HTTP,HTTPS,Telnet,Syslog,Private MIBMIB P-BRIDGE MIB,Q-BRIDGE MIB,IEEE8021-SPANNING-TREE-MIB,IEEE8021-PAE-MIB,IEEE8023-LAG-MIB,LLDP-EXT-DOT1-MIB,LLDP-EXT-DOT3-MIB,SNMPv2-MIB,RMON MIB Groups1,2,3,9Redundancy Protocols STP,RSTP,Turbo Ring v2,Turbo Chain,Ring Coupling,Dual-Homing,Link AggregationSecurity Broadcast storm protection,Rate Limit,Trust access control,Static Port Lock,MACSticky,HTTPS/SSL,SSH,RADIUS,TACACS+,Login and Password PolicyTime Management SNTP,NTP Server/Client,NTP AuthenticationProtocols IPv4/IPv6,TCP/IP,UDP,ICMP,ARP,RARP,TFTP,DNS,NTP Client,DHCP Server,DHCP Client,802.1X,QoS,HTTPS,HTTP,Telnet,SMTP,SNMPv1/v2c/v3,RMON,SyslogSwitch PropertiesMAC Table Size16KJumbo Frame Size9.216KBMax.No.of VLANs256VLAN ID Range VID1to4094IGMP Groups512Priority Queues4Packet Buffer Size1MBLED InterfaceLED Indicators PWR1,PWR2,STATE,FAULT,MSTR/HEAD,CPLR/TAIL,SYNCSerial InterfaceConsole Port RS-232(TxD,RxD,GND),8-pin RJ45(115200,n,8,1)USB InterfaceUSB Connector USB Type A(Reserved)Input/Output InterfaceAlarm Contact Channels1,Relay output with current carrying capacity of1A@24VDCDigital Input Channels1Digital Inputs+13to+30V for state1-30to+3V for state0Max.input current:8mAButtons Reset buttonDIP Switch ConfigurationDIP Switches Turbo Ring,Master,Coupler,ReservePower ParametersConnection2removable4-contact terminal block(s)Pre-installed Power Module-LV/-LV-T models:PWR-100–LV-HV/-HV-T models:PWR-105-HV-I-LVA/-LVA-T models:PWR-101-LV-BP-I-LVB/-LVB-T models:PWR-103-LV-VB-INote The EDS-4012Series supports modular power supplies.The model names and powerparameters are determined by the installed power module.For example:EDS-4012-4GS-T+PWR-100–LV=EDS-4012-4GS-LV-TEDS-4012-4GS-T+PWR-105-HV-I=EDS-4012-4GS-HV-TIf you install a different power module,refer to the specifications of the correspondingmodel.For example,if you replace the power module of the EDS-4012-4GS–LV-Twith the PWR-105–HV-I,refer to the specifications of the EDS-4012–4GS-HV-T.Input Voltage-LV/-LV-T models:12/24/48VDC,Redundant dual inputs-HV/-HV-T models:110/220VDC/VAC,Single input-LVA/-LVA-T models:48VDC,Redundant dual inputs-LVB/-LVB-T models:12/24/48VDC,Redundant dual inputsOperating Voltage-LV/-LV-T models:9.6to60VDC-HV/-HV-T models:88to300VDC,85to264VAC-LVA/-LVA-T models:44to57VDC(>52VDC for PoE+output recommended)-LVB/-LVB-T models:12to57VDC(>52VDC for PoE+output recommended)Input Current-LV/-LV-T models:12-48VDC,1.50-0.40A or24VDC,0.70A-HV/-HV-T models:110-220VAC,50-60Hz,0.30-0.20A or110-220VDC,0.30-0.20A-LVA/-LVA-T models:48VDC,5.42A-LVB/-LVB-T models:12/48VDC,7.46/4.27A or24VDC,7.26APower Consumption(Max.)EDS-4012-4GS-LV/-T models:10.52WEDS-4012-4GS-HV-/T models:12.22WEDS-4012-4GC-LV/-T models:10.7WEDS-4012-4GC-HV/-T models:13.35WEDS-4012-8P-4GS-LVA/-T models:Without PoE:13.34WWith PoE:Max.240W for total PD power consumption@48VDC inputEDS-4012-8P-4GS-LVB/-T models:Without PoE:15.32WWith PoE:Max.180W for total PD power consumption@48VDC inputMax.150W for total PD power consumption@24VDC input(Max.120W for-T model)Max.62W for total PD consumption@12VDC inputMax.PoE Power Output per Port90WOverload Current Protection SupportedReverse Polarity Protection SupportedPhysical CharacteristicsIP Rating IP40Dimensions55x140x120mm(2.17x5.51x4.72in)Weight827g(1.82lb)Installation DIN-rail mounting,Wall mounting(with optional kit) Housing MetalEnvironmental LimitsOperating Temperature Standard Models:-10to60°C(14to140°F)Wide Temp.Models:-40to75°C(-40to167°F) Storage Temperature(package included)-40to85°C(-40to185°F)Ambient Relative Humidity5to95%(non-condensing)Standards and CertificationsIndustrial Cybersecurity IEC62443-4-1IEC62443-4-2Safety UL61010-2-201,EN62368-1(LVD)EMC EN55032/35,EN61000-6-2/-6-4EMI CISPR32,FCC Part15B Class AEMS IEC61000-4-2ESD:Contact:8kV;Air:15kVIEC61000-4-3RS:80MHz to1GHz:20V/mIEC61000-4-4EFT:Power:4kV;Signal:4kVIEC61000-4-5Surge:Power:4kV;Signal:4kVIEC61000-4-6CS:10VIEC61000-4-8PFMFMaritime-LV/-LV-T,PoE/PoE-T models:DNV,ABS,NK,LR Vibration IEC60068-2-6Shock IEC60068-2-27Freefall IEC60068-2-32Railway EN50121-4Traffic Control NEMA TS2Power Substation IEC61850-3,IEEE1613Class1MTBFTime EDS-4012-4GC-LV/-T models:1,036,336hrsEDS-4012-4GC-HV/-T models:497,392hrsEDS-4012-4GS-LV/-T models:874,838hrsEDS-4012-4GS-HV/-T models:456,870hrsEDS-4012-8P-4GS-LVA/-T models:799,780hrsEDS-4012-8P-4GS-LVB/-T models:759,924hrs Standards Telcordia SR332WarrantyWarranty Period5yearsDetails See /warrantyPackage ContentsDevice1x EDS-4012Series switchDocumentation1x quick installation guide1x product notice,Simplified Chinese1x product certificates of quality inspection,Simplified Chinese1x warranty cardDimensionsOrdering InformationModel Name 10/100BaseT(X)Ports(RJ45Connector)PoE10/100BaseT(X)Ports(RJ45Connector)100/1000BaseSFPSlotsCombo Ports(10/100/1000BaseT(X)or100/1000BaseSFP)OperatingVoltagePre-installedPower ModuleOperatingTemp.EDS-4012-4GS-LV8–4–9.6to60VDC PWR-100-LV-10to60°C EDS-4012-4GS-LV-T8–4–9.6to60VDC PWR-100-LV-40to75°CEDS-4012-4GS-HV8–4–88to300VDC,85to264VACPWR-105-HV-I-10to60°CEDS-4012-4GS-HV-T8–4–88to300VDC,85to264VACPWR-105-HV-I-40to75°CEDS-4012-4GC-LV8––49.6to60VDC PWR-100-LV-10to60°C EDS-4012-4GC-LV-T8––49.6to60VDC PWR-100-LV-40to75°CEDS-4012-4GC-HV8––488to300VDC,85to264VACPWR-105-HV-I-10to60°CEDS-4012-4GC-HV-T8––488to300VDC,85to264VACPWR-105-HV-I-40to75°CEDS-4012-8P-4GS-LVA–84–44to57VDC(>52VDC for PoE+outputrecommended)PWR-101-LV-BP-I-10to60°CEDS-4012-8P-4GS-LVA-T –84–44to57VDC(>52VDC for PoE+outputrecommended)PWR-101-LV-BP-I-40to75°CEDS-4012-8P-4GS-LVB–84–12to57VDC(>52VDC for PoE+outputrecommended)PWR-103-LV-VB-I-10to60°CEDS-4012-8P-4GS-LVB-T –84–12to57VDC(>52VDC for PoE+outputrecommended)PWR-103-LV-VB-I-40to75°CAccessories(sold separately)SFP ModulesSFP-1GEZXLC SFP module with11000BaseEZX port with LC connector for110km transmission,0to60°C operatingtemperatureSFP-1GEZXLC-120SFP module with11000BaseEZX port with LC connector for120km transmission,0to60°C operatingtemperatureSFP-1GLHLC SFP module with11000BaseLH port with LC connector for30km transmission,0to60°C operatingtemperatureSFP-1GLHXLC SFP module with11000BaseLHX port with LC connector for40km transmission,0to60°C operatingtemperatureSFP-1GLSXLC SFP module with11000BaseLSX port with LC connector for1km/2km transmission,0to60°Coperating temperatureSFP-1GLXLC SFP module with11000BaseLX port with LC connector for10km transmission,0to60°C operatingtemperatureSFP-1GSXLC SFP module with11000BaseSX port with LC connector for300m/550m transmission,0to60°Coperating temperatureSFP-1GZXLC SFP module with11000BaseZX port with LC connector for80km transmission,0to60°C operatingtemperatureSFP-1GLHLC-T SFP module with11000BaseLH port with LC connector for30km transmission,-40to85°C operatingtemperatureSFP-1GLHXLC-T SFP module with11000BaseLHX port with LC connector for40km transmission,-40to85°Coperating temperatureSFP-1GLSXLC-T SFP module with11000BaseLSX port with LC connector for1km/2km transmission,-40to85°Coperating temperatureSFP-1GLXLC-T SFP module with11000BaseLX port with LC connector for10km transmission,-40to85°C operatingtemperatureSFP-1GSXLC-T SFP module with11000BaseSX port with LC connector for300m/550m transmission,-40to85°Coperating temperatureSFP-1GZXLC-T SFP module with11000BaseZX port with LC connector for80km transmission,-40to85°C operatingtemperatureSFP-1G10ALC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for10km transmission;TX1310nm,RX1550nm,0to60°C operating temperatureSFP-1G10BLC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for10km transmission;TX1550nm,RX1310nm,0to60°C operating temperatureSFP-1G20ALC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for20km transmission;TX1310nm,RX1550nm,0to60°C operating temperatureSFP-1G20BLC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for20km transmission;TX1550nm,RX1310nm,0to60°C operating temperatureSFP-1G40ALC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for40km transmission;TX1310nm,RX1550nm,0to60°C operating temperatureSFP-1G40BLC WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for40km transmission;TX1550nm,RX1310nm,0to60°C operating temperatureSFP-1G10ALC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for10km transmission;TX1310nm,RX1550nm,-40to85°C operating temperatureSFP-1G10BLC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for10km transmission;TX1550nm,RX1310nm,-40to85°C operating temperatureSFP-1G20ALC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for20km transmission;TX1310nm,RX1550nm,-40to85°C operating temperatureSFP-1G20BLC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for20km transmission;TX1550nm,RX1310nm,-40to85°C operating temperatureSFP-1G40ALC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for40km transmission;TX1310nm,RX1550nm,-40to85°C operating temperatureSFP-1G40BLC-T WDM-type(BiDi)SFP module with11000BaseSFP port with LC connector for40km transmission;TX1550nm,RX1310nm,-40to85°C operating temperatureSFP-1FELLC-T SFP module with1100Base single-mode with LC connector for80km transmission,-40to85°Coperating temperatureSFP-1FEMLC-T SFP module with1100Base multi-mode,LC connector for2/4km transmission,-40to85°C operatingtemperatureSFP-1FESLC-T SFP module with1100Base single-mode with LC connector for40km transmission,-40to85°Coperating temperaturePower SuppliesHDR-60-2460W/2.5A DIN-rail24VDC power supply,universal85to264VAC or120to370VDC input voltage,-30to70°C operating temperatureNDR-120-24120W/5.0A DIN-rail24VDC power supply,universal90to264VAC or127to370VDC input voltage,-20to70°C operating temperatureNDR-120-48120W/2.5A DIN-rail48VDC power supply,universal90to264VAC or127to370VDC input voltage,-20to70°C operating temperatureNDR-240-48240W/5.0A DIN-rail48VDC power supply,universal90to264VAC or127to370VDC input voltage,-20to70°C operating temperatureMDR-40-24DIN-rail24VDC power supply with40W/1.7A,85to264VAC,or120to370VDC input,-20to70°Coperating temperatureMDR-60-24DIN-rail24VDC power supply with60W/2.5A,85to264VAC,or120to370VDC input,-20to70°Coperating temperature©Moxa Inc.All rights reserved.Updated Jun17,2022.This document and any portion thereof may not be reproduced or used in any manner whatsoever without the express written permission of Moxa Inc.Product specifications subject to change without notice.Visit our website for the most up-to-date product information.。

WDR-823A调试指导手册

WDR-823A微机电容器保护装置调试指导手册目录1.外观检查 (3)2. 绝缘耐压试验 (3)3.逆变电源的检查 (6)4.上电初步检查 (6)4.1显示情况 (6)4.2基本操作 (6)4.3软件版本及工程配置检查 (6)6 时钟检查 (7)6.1 时钟的整定 (7)6.2 时钟失电的保持功能 (7)6.3 时钟的准确性检查 (7)7 定值检查 (7)7.1定值正确性检查 (7)7.2失电后定值检查 (7)8. 开入检查 (7)9 开出传动检查 (8)10.模入回路检查 (9)10.1零漂校正 (9)10.2系数校正 (9)11 保护功能测试 (9)11.1试验接线及准备工作 (10)11.2过流保护功能测试 (10)11.3差压保护功能测试 (11)11.4低压保护功能测试 (11)11.5过压保护功能测试 (11)12.连续通电试验 (11)13.试验恢复工作 (11)概述：本调试大纲以检查配线正确性为目的，同时检测装置硬件完好及主要设计回路功能正常。

调试过程依据具体工程设计图纸，开入量测试正电的施加以硬压板或把手位置驱动优先，剩余部分及交流量在距N端子电气距离最远屏端子上施加；开出部分接点通断的检查在距N端子电气距离最远屏端子上测试。

1.外观检查1.1.检查工艺流程卡信息完整并正确。

1.2.检查装置型号、规格、编号与流程卡及技术协议一致。

1.3.检查机箱插件编号顺序正确（参见下图1）1.4.检查机箱、面板无任何磕碰划伤及污迹。

1.5.检查机箱标签清晰完整且粘接牢固1.6.检查装置面板及按键印字清晰。

1.7.检查箱体缝隙均匀及螺丝紧固。

1.8.检查机箱接地标识位置正确1.9.检查屏体，铭牌、机箱布置、压板标签，空气开关型号与协议一致1.10.依据大屏设计图纸检查配线正确；1.11.用万用表检查直流电压回路、交流电压回路无短路；3#4#2#1#信号插件电源插件CPU插件交流插件3#4#2#1#信号插件电源插件CPU插件交流插件通信插件TX基本型P型其中：1# 交流输入；2# CPU插件；3#电源插件、4# 信号插件。

台湾约尔通信息技术有限公司蓝牙低功耗模块产品介绍说明书

Wireless Module BluetoothⓇ low energy Module
Overview
May 30, 2018 Version 1.8
TAIYO YUDEN BluetoothⓇ low energy Module Line-Up Taiyo Yuden BluetoothⓇ low energy Module
EYSGCNAWY-1X http://www.yuden.co.jp/or/product/category/module/EYSGCNAWY-1X.html EYSGJNAWY-1X http://www.yuden.co.jp/or/product/category/module/EYSGJNAWY-1X.html EYSGCNAWY-WX http://www.yuden.co.jp/or/product/category/module/EYSGCNAWY-WX.html EYSGJNAWY-WX http://www.yuden.co.jp/or/product/category/module/EYSGJNAWY-WX.html
EYSGCN Series
Basic
Application Embedded
Embedded antenna
Small
Ext. 32kHz X’tal Ext. LC for DC/DC
5.1 x 11.3 x 1.3 mm
EYSGJN Series
Basic
EYAGJN Series Application
ZXX
ZXX
RAM 32kB RAM 16kB
ANT + BLE SoftDevice SoftDevice S110
S310

Ultrastar DC SS530 SAS SSD说明书

Maximize Storage and Server Scalability with SAS SSDsData is transforming the world and growing at an exponential pace. The SAS interface continues its dominance in traditional enterprise storage arrays, making the ever-increasing volume of data rapidly and reliably available. Storage solutions depend on SAS’s protection features, such as dual-port failover for redundancy, and SAS’s high reliability to power mission-critical applications such as ERP, OLTP, OLAP, and more. Designed with a dual-port 12Gb/s SAS interface for seamless integration into enterprise environments, the Ultrastar ® DC SS530 SAS SSD is available in capacities from 400GB to 15.36TB¹, double the capacity of prior generations. Delivering performance up to 440,000 random read and 320,000 random write IOPS—best in class among current 12Gb/s SAS SSDs—the Ultrastar DC SS530 can help to drive faster data analytics, drive higher productivity, and power business decision-making.Proven Architecture with Industry-Leading Quality and ReliabilityUltrastar DC SS530 leverages the proven architecture of the prior generation Ultrastar SS300 with second generation 3D TLC NAND flash memory. The Ultrastar DC SS530 achieves an extraordinary 0.35% annual failure rate (AFR) or 2.5 million hours mean-time-between-failure (MTBF). DC SS530 offers three endurance options of 1, 3 and 10 drive writes per day (DW/D) to meet the most stringent data center requirements.Help keep confidential data secure by deploying self-encrypting drive technology that supports Trusted Computing Group (TCG) Enterprise standards for security services and FIPS 140-2 validation for cryptographic-enabled drives that are required for certain government applications. The Ultrastar DC SS530 is backed by a five-year limited warranty or the maximum petabytes (PB) written (based on capacity), whichever comes first.Trust Your Storage Systems with SSD Products Developed by Experts in Enterprise StorageUltrastar SAS SSDs leverage decades of proven enterprise storage expertise in Serial Attached SCSI (SAS) design, reliability, firmware, customer qualification, and system integration. The synergistic relationship between the new throughput-enhancing SSDs and traditional HDDs provides cost-effective, end-to-end enterprise-class storage options that deliver reliability, compatibility, capacity, cost savings, and systemperformance. This combination makes Ultrastar storage drives an ideal choice to help meet escalating reliability, endurance, and performance requirements in the most demanding data center environments.Highlights•2nd generation 3D TLC NAND flash for ultra-high performance and endurance •12Gb/s SAS interface for maximum throughput •Advanced power-loss and data-management technology •Self-encrypting models conform to TCG’s Enterprise specificationApplications•Ultra-high performance tier-0 enterprise storage •Enterprise-class servers and high performance computing (HPC) •Software-defined storage (SDS) •Online transaction processing (OLTP) •Finance and e-commerce •Database analyticsDATA SHEETSAS DATA CENTER SSDFeatures & Benefits15.36TB – 400GB | 3D TLC 2.5-inch SFF | SAS 12Gb/sWDS34-EN-US-0919-02© 2018-2019 Western Digital Corporation or its affiliates. All rights reserved. Produced 07/18, rev. 09/19. Western Digital, the Western Digital logo and Ultrastar are registered trademarks or trademarks of Western Digital Corporation or its affiliates in the US and/or other countries. All other marks are the property of their respective owners. References in this publication to Wesstern Digital products, programs, or services do not imply that they will be made avillable in all countries. Product specifications provided are sample specifications that are subject to change and do not constitute a warranty. Please visit the Support section of our website, , for additional information on product specifications. Pictures shown may vary from actual products.Specifications10DW/D3DW/D1DW/DModel Numberx in Model Number denotes Encryption level: 0 = Instant Secure Erase 1 = TCG Encryption4 = No Encryption, Secure Erase5 = TCG + FIPSWUSTM3232ASS20x WUSTM3216ASS20x WUSTM3280ASS20x WUSTM3240ASS20xWUSTR6464ASS20x WUSTR6432ASS20x WUSTR6416ASS20x WUSTR6480ASS20x WUSTR6440ASS20xWUSTR1515ASS20x WUSTR1576ASS20x WUSTR1538ASS20x WUSTR1519ASS20x WUSTR1596ASS20x WUSTR1548ASS20xConfigurationInterface SAS 6/12Gb/s supports wide port @ 12Gb/s Capacity13.2TB / 1.6TB / 800GB / 400GB6.4TB / 3.2TB / 1.6TB / 800GB / 400GB15.36TB / 7.68TB / 3.84TB / 1.92TB /960GB / 480GBEndurance (Drive Writes per Day - DW/D)21031Maximum Terabytes Written (TBW)²59,690 / 29,410 / 15,220 / 7,63036,170 / 17,520 / 9,410 / 4,700 / 2,35030,110 / 15,050 / 7,000 / 3,760 / 1,880 / 940Form Factor2.5-inch 15mm SFF Flash Memory Technology3D TLC NANDPerformance³Read Throughput (max MiB/s, Seq 128KiB)2,1502,1502,150Write Throughput (max MiB/s, Seq 128KiB)2,1202,1202,120Read IOPS (max, Rnd 4KiB)440,000440,000440,000Write IOPS (max, Rnd 4KiB)320,000240,000100,000Mixed IOPS (70/30 R/W, max, 4KiB)430,000330,000190,000Read/Write Latency⁴ (μs, avg)92 / 2692 / 2792 / 36ReliabilityUnrecoverable Bit Error Rate (UBER) 1 in 1017MTBF 5 (M hours)2.5Annualized Failure Rate⁵ (AFR)0.35%Availability (hrs/day x days/wk)24x7Limited Warranty⁶5 yearsPowerRequirement (+/- 5%)+5 VDC, +12VDCOperating (W, typical)9, 11, 14Idle (W, average)3.2Physical Sizez-height (mm)15Dimensions (width x depth, mm)70.1 x 100.45Weight (g, max)175EnvironmentalOperating Temperature⁷0o to 75o C Non-operating Temperature-40o to 85o CUltrastar ® DC SS5305601 Great Oaks ParkwaySan Jose, CA 95119, USAUS (Toll-Free): 800.801.4618International: /dc-ss530One megabyte (MB) is equal to one million bytes, one gigabyte (GB) is equal to 1,000MB (one billion bytes), and one terabyte (TB) is equal to 1,000GB (one trillion bytes) when referring to storage capacity. Accessible capacity will vary from the stated capacity due to formatting, system software, and other factors.² Endurance rating based on DW/D using 4KiB random write workload over 5 years³ Performance will vary by capacity point, or with the changes in useable capacity. Consult product manual for further details. All performancemeasurements are in full sustained mode and are peak values. Subject to change. 1MiB=1,048,576 bytes or 2, 1KiB= 1,024 bytes or 2.⁴ Average R/W latency at 4KiB QD=1⁵ MTBF and AFR specifications are based on a sample population and are estimated by statistical measurements and acceleration algorithms under typical operating conditions for this drive model. MTBF and AFR ratings do not predict an individual drive’s reliability and do not constitute a warranty.⁶ The warranty for the product will expire on the earlier of (i) the date when the flash media has reached one-percent (1%) of its remaining life or (ii) the expiration of the time period associated with the product.⁷ Internal drive temperature as measured via the drive’s temperature sensor.How to Read the Ultrastar Model NumberExample: WUSTR6464ASS201=6.4TB, SAS 12Gb/s, TCG W = Western Digital U = Ultrastar S = StandardTR = NAND type/endurance(TM=TLC/mainstream endurance, TR= TL C/read-intensive)64 = Full capacity (6.4TB)64 = Capacity of this model(15=15.2TB, 76=7.6TB, 38=3.84TB 32=3.2TB, 19=1.92TB,16=1.6TB, 96=960GB, 80=800GB, 48=480GB, 40=400GB)A = Generation codeS = Small form factor (2.5” SFF)S2 = I nterface, SAS 12Gb/s 1 = Encryption setting(0=Instant Secure Erase, 1=TCG Enterprise encryption,4=No encryption/Secure Erase, 5 = TCG+FIPS)。

Adaptec 智能存储解决方案产品指南说明书

Data Center Solutions Adaptec ® Product GuideSmart Storage Performance, Power, Security and ReliabilityWith the massive growth of data centers, performance, power and reliability are more important considerations than ever.Performance requirements are driven by both the increased adoption of Flash-based SSDs and the increasing sizes of HDD arrays. Data centers are looking to take advantage of the performance that these Flash-based drives promise and require storage solutions that can deliver manageability and data availability without compromising performance.Power is a significant component of a data center’s operating expenses.Optimizing power for cold storage tiers in the data center, for example, delivers substantial benefits to the bottom line.Data security has become one of the highest priorities for data centers and cloud computing environments as enterprises seek to safeguard customer information, classified company documentation and communications, financial records, employee payroll records and other confidential data.As more mission-critical data finds its way to data centers, end customers insist on reduced downtime, improved response times to issues and a more positive end-user experience overall.The Adaptec ®SmartRAID 3100, SmartHBA 2100 and HBA 1100 product fam -ilies are based on the company’s latest 28 nm SmartROC 3100 and SmartIOC 2100 storage controller Integrated Circuits (ICs). The SmartRAID 3162-8i /e adapter includes maxCrypto™, the industry’s only data-at-rest controller-based encryption solution, that provides a superior solution over self-encrypting drives.Microchip’s unified Smart Storage stack powers the entire family of products,leveraging core IP that has shipped in over 30 million servers, delivering one of the industry’s most reliable and highest-performing storage controller software platforms.Technology Leadership With Data EncryptionSolutions for data-at-rest encryption are now a security requirement in manymarket segments such as health care, finance, e-commerce, federal government branches and insurance—a significant overall percentage of the deployed storage.Data center managers face the challenge of safeguarding data while still meeting continually-increasing performance demands for large-scale applications, such as web serving, file serving, databases, Online Transaction Processing (OLTP), machine learning and High-Performance Computing (HPC).Now available, the SmartRAID 3162-8i/e with maxCrypto, delivers dataprotection with little to no impact on latency or I/O performance. The 3162-8i/e offers superior advantages over Self-Encrypting Drives (SEDs) and integrates seamlessly into existing storage infrastructures, allowing data centers to deploy a uniform, scalable encryption strategy across the enterprise.Controller-Based EncryptionValue Proposition Versus Self-Encrypting DrivesPrevents data snooping between controller and drivesRe-key support for wrapping keys or data volume keys Encrypted controller cacheSuperior Security vs. SEDController Based EncryptionDelivers Superior Security & FlexibilityAllows in-place encryption of existing data (volume remains available)No separate “special” (SED) drives for end-customers to manage64 Logical Drive support for flexible mapping to OS Users and ApplicationsSuperior Flexibility vs. SEDValue Proposition versus Self-Encrypting Drives (SED)4rASATA-SBACK-I-HDmSAS-4SATA-SBACK-E-HDmSAS-HDmSAS ACK-E-HDmSAS-mSASThe Microchip name and logo, the Microchip logo, Adaptec and maxCrypto is a trademark are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. All other trademarks mentioned herein are property of their respective companies.© 2020, Microchip Technology Incorporated. All Rights Reserved. 1/20 DS00003375ASupportMicrochip is committed to supporting its customers in developing products faster and more efficiently. We maintain a worldwide network of field applica -tions engineers and technical support ready to provide product and system assistance. For more information, please visit :• Technical Support: /support • Evaluation samples of any Microchip device:/sample • Knowledge base and peer help:/forums• Sales and Global Distribution: /salesTrainingIf additional training interests you, Microchip offers several resources including in-depth technical training and reference material, self-paced tutorials and significant online resources.• Overview of Technical Training Resources: /training • MASTERs Conferences:/masters • Developer Help Website:/developerhelp • Technical Training Centers:/seminarsMicrochip Technology Inc. | 2355 W. Chandler Blvd. | Chandler AZ, 85224-6199。

1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。

SDS-823X
Trusted TM Industrial Control System Trusted TM
Power system-T823X
Issue 3 Jan 2006
DESCRIPTION
The Trusted TM
Power System is a high density flexible power supply designed to convert main line voltages of either 110V/240Vac. Outputs are
either 24Vdc for Trusted TM
product or 24-28Vdc adjustable field power.
The power supply system consists of a 1U Power Shelf with mechanical support, containing up to three 750W Power Packs. The Power Packs load share in configurations using 1 or more Power Shelf. Each Power Pack has an individual supply connection via a mechanically retained IEC320 type connector. Each Power Shelf can supply 2250Watts of power or 1500Watts with n+1 redundancy from a single source. Multiple units can be connected for further capacity or redundancy requirements.
Diagnostics information of Power Pack status is provided via the Power Port, which connects to the rear of the Power Shelf. This device monitors input and output conditions and reports out of range faults and over temperature/fan failure using relay contacts. The Power Port also allows connection of the optional rack mounted Power Controller for live configuration of output voltage and current, monitoring up to 12 Power Packs in 4 Power Shelves.
Product No. Product name Description
T8230
Power Shelf
19” x 1U chassis for up to 3 Power Packs. Includes 4U fixing kit, Power Port and mains plugs.
T8231 Power Pack 24Vdc 750Watt, universal input, 24Vdc out. T8232 Power Pack 28Vdc 750Watt, universal input, 28Vdc out. T8233 Power Port Plug in diagnostic interface.
T8234
Power Controller
For live adjustment of output voltage. 19”x1U
T8235 Power Shield
Covers unused Power Pack positions TC323
Power Shelf Interconnect
Ribbon cable for power sharing between 2-4 Power Shelves and connection to Power Controller
FEATURES
Redundant and N+1 configurations
Hot replaceable power Packs
Current sharing Current limiting Power factor correction
Diagnostics contacts
Configurable output voltage
Input/output fail
diagnostics per power pack
SDS-823X
Trusted TM Industrial Control System
Trusted TM Power system-T823X
ICS Triplex
Technical data sheets are intended for information and guidance. The Company has a policy of continual product development and improvement. Specifications are subject to change
without notice. For latest information, visit our Website:-
ASSEMBLY LAYOUT
ELECTRICAL SPECIFICATION
Voltage Range - Input 90V ac to 264V ac
Voltage Range - Output 24Vdc or 28V dc (23-28 adjustable) Frequency Range 47Hz to 63Hz Inrush Current 50A max
Power Factor 0.95min, 0.99typical Efficiency 78 – 84% Hold-up Time 20ms min
Output Power 750W per Power Pack
Isolation voltage 3kVac, Primary to secondary
1.5kVac Primary or secondary to ground
MECHANICAL SPECIFICATION
Dimensions (HxWxD): 43.5mm x 483mm x 340mm
(1.71ins x 19ins x 13.36ins)
Note: Mounting bracket requires minimum 4U rack height. Unused space may be populated by other equipment.
Weight (fully populated) 10kg (approx.) 22lbs (approx.)
ENVIRONMENTAL
Operating Temperature:
0°C to 60°C (30°F to 140°F)
Operating Humidity: 5to 95%, non-condensing
Vibration: 10 to 57Hz ±0.075mm 57 to 150Hz 1g
Shock:
15g, ½ sine wave, 11ms
EMI (IEC 801): ESD
Air discharge to 15kV Contact discharge to 8kV
Radiated Fields
10V/m, 27MHz to 500MHz
Transients and Bursts
2kV, 2.5kHz for t=60 seconds。