1、QCFC

Name of equipment Control parameters Item name Control standardMeasurementinstrument/meIPQCinspectionProductioninspectionPCM board fully <SOP for PCMAppearance1.No bridge ,no weak ,and no acerbsoldering dot .3.For Ni pad,No deformation,smudginessVisual8timesProductsamplingFirstarticle<DPPM control chart><Scotoma test record>Kapton pasted on <SOP for Kaptonpasted on side>Automatically pasteRun speed:15PCS/minAppearance1. In the correct position,the edge of2. Paste firmly,no impurity ,no drape.VisualProductsamplingOperatorself-testIPQC inspection dailyreportAppearance<Standardinspection Appearance1.The surface of cell has nobreakage,protruding scratch , bubbleVisualProductsamplingFirstarticle<Scotoma test record> Product control projectRecords ReprotControltargetMain processeMachiningProcess nameStandardOperatingEquipment control projectFile Sort Document NumbersStandard FilePage code McNair Newpower Co. LtdName of equipment Control parameters Item name Control standardMeasurementinstrument/meIPQCinspectionProductioninspectionWelding PTCon anode ultrasonic Ultrasoundmachines,0.4MPa3.Super vitality power:30%-50%Weldingeffection21. Ultrasonic welding on the correctposition30.5kgf.2..VisualTensileProductsamplingFirstArticle<Pull test record>Pastingkapton on<SOP for PasteKapton on PTC>Cut tapemachineAppearance1.Film model:Width is 12mm,Thickness is2. In the correct position,the PTCshould be covered of kapton,and theVisualProductsamplingOperatorself-testAutomatically pasting<SOP forautomatically Automatically pastingAppearance2.No drape,and the dupont paper shouldnoumenon of cell.welding,fired fire,and break out thetabVisualTensileProductsamplingFirstArticleProduct control projectRecords ReprotControltargetFile Sort Document Numbers Standard FilePage codeMain processe MachiningProcess nameStandardOperatingEquipment control projectMcNair Newpower Co. LtdName of equipment Control parameters Item name Control standardMeasurementinstrument/meIPQCinspectionProductioninspectionFullyinspecting<SOP for fully AdjustableUPS4.0kg Appearance1.It should have 2 effective weldingjoints. No poor welding, no emptyVisualProductsamplingFirstarticle<DPPM control chart>Winding PCM plate and<Sop forwinding PCMFixingclamp for Appearance1.Operating technique is correctly.2.The surface is clean,no residueVisualProductsamplingOperatorself-Put the battery into <Sop for putbattery intoclamp forplastic91.8mm*57.86mm*4.05mm Appearance1. Battery should be installedplastic frame.0.3mm5.Fall down test frequency:5pcs/dayCaliperVisualProductsamplingOperatorself-<Fall down testrecord>Page codeRecords ReprotFile Sort Document Numbers Standard FileMain processe MachiningProcess nameStandardOperatingEquipment control project Product control projectControltarget McNair Newpower Co. LtdName of equipment Control parameters Item name Control standardMeasurementinstrument/meIPQCinspectionProductioninspectionPastingkapton on<Sop forpasting kapton Cut tapemachineAppearance 2.The kapton should be pasted smooth,no drape.VisualProductsamplingOperatorself-Semi-finished<SOP for semi-finished Comprehensive testingtesting2.Load voltage:3.65-3.95v3.impedance : 30-115mohm6.short circuit protectionFaction1. No low/high/impedance bad2. No charge /discharge badfit the specifcationComperhensivescannerProductsamplingFirstarticle<DPPM control chart><Test report record><Go no go sample>double-side adhesive and <SOP for paste Automatically addAppearance5.3M1.Double-side adhesivemodel:74mm*43mm*0.05mmVisualProductsamplingOperatorself-Page codeProduct control projectRecords ReprotFile Sort Document Numbers Standard FileMain processe MachiningProcess nameStandardOperatingEquipment control projectControltarget McNair Newpower Co. LtdName of equipmentControl parameters Item name Control standardMeasurement instrument/meIPQC inspection Production inspectionPasting Label<Sop for pasting label>Automatically pasting Appearance bel model:Contents are as same as the specification,and the colour is asVisualProduct sampling Operator self-Finished dimensions <Sop for AutomaticallyDimensionsAutomaticallyProductsamplingFirst article <DPPM control chart><Test report record>finished comprehensiv <SOP for Comprehensi ve testingtesting 2.Load voltage:3.65-3.95v 3.impedance : 30-115mohm 6.short circuit protectionFaction1. No low/high/impedance bad2. No charge /discharge bad fit the specifcationComperhensive scannerProduct sampling First article <DPPM control chart><Test report record>Page codeProduct control projectRecords ReprotStandard FileControl targetMainprocesse MachiningProcess nameStandard Operating Equipment control projectMcNair Newpower Co. LtdName of equipment Control parameters Item name Control standardMeasurementinstrument/meIPQCinspectionProductioninspectionFinished appearance <StandardAppearance According to the <Standard inspectionprocedure>VisualProductsamplingFirstarticle<DPPM control chart><Scotoma test record>Scanning weight/Loadi<SOP forScanner,electronicQuantity1. 150pcs/lot,The quantity is accurate,no excessive or short loading3.Customer Payt:58-000049-00VisualProductsamplingOperatorself-test<Send sample record><Program check record>< OQC standardinspectionAppearanceFunctionAccording to the <standard for finisnedinspection>OQC sampleinspection<Send sample record><OQC InspectionStorage<Materialcontrol Quantityspec1.Quantity is accurate,No excessive orshort loading phenomenonVisualelectronicMCacceptance<Product storageRecord>Article Record>and <IPQC inspection daily report>.Product control projectRecords ReprotControltargetMain processe MachiningProcess nameStandardOperatingEquipment control projectStandard FilePage code McNair Newpower Co. Ltd。