十字旋转屏报告

旋转LED显示屏设计与测试
姓名：姜 x
学号： 20112410212
班级：（二）
专业：电子信息工程
一、实验任务
基于视觉暂留原理，设计一种旋转式LED显示屏，使其能够显示预设的文字，图案等。

二、显示原理
人眼在观察景物时，光信号传入大脑神经，需经过一段短暂的时间，光的作用结束后，视觉形象并不立即消失，这种残留的视觉称“后像”，视觉的这一现象则被称为“视觉暂留”。

肉眼在24帧/秒以上就不会看到闪烁的，所以只要保证电机的速度能在一秒转24圈以上，这样的话人眼就觉得旋转的字很稳定很清晰的显示在空中了。

如果我们用电机带动led主板转动，以stc89c52单片机为控制中心，16个io 口分别控制16个led，再加上一个红外发射管，一个红外接收管。

led主板上的红外接收管每转动一圈红外接收管就会导通一次。

一旦导通，单片机检测到引脚的低电平，便让单片机开始有规律的控制16个led的亮灭，这样，由于人眼的“视觉暂留”效应，便能看到显示屏上显示的文字或图像了。

要想准确显示一个字体或者图形，我们就要准确的给16个管脚赋上有规律的高低电平，要想知道怎样赋值，我们需要对文字或者图形取模，因为我们用的是16个led灯，所以我们取一个16*16的中文字，如图1示
图1 对汉字取模
从第一列开始向下每取8个点作为一个字节，如果最后不足8个点就补满8位。

取模顺序是从低到高，即第一个点作为最低位。

取模后数据如下：
0xFF,0x7F,0xFF,0xBF,0x3F,0xC8,0xBF,0xFB,0xBF,0xFB,0xBF,0xEB,0x80,0x9B,0x B7,0xFB,0xB7,0xEB,0xB7,0x9B,0xB7,0xFB,0x37,0xF8,0xF7,0xEF,0xF7,0x1F,0xFF, 0xFF,0xFF,0xFF,/*"点",0*/
现在我们知道16*16取模是一列一列取的了，一列有2个字节，一共16列，所以一个16*16的汉字就有32个字节，需要占用单片机的Code空间32个字节。

Led每旋转一周红外接收管接收信号时，单片机便开始根据取模后的数组开始依次点亮16个led。

这样，便能显示文字或者图形了。

三、硬件设计
控制芯片采用STC89C52，结构框图设计如图2所示
图2 系统结构框图
本系统采用无线供技术。

利用自激震荡电路，把5v直流电压转换成交流电压。

然后通过线圈电磁感应，给led主板供电。

电源电路原理图如图3所示
图3 电源电路原理图
本系统用p2口，p4口，p5口控制16个led灯，次级感应线圈产生感应电压系统电路原理图如图4所示
图4 系统电路原理图
制作完成后，下载硬件测试程序进行测试，如果16个led灯能够全部点亮，
则制作成功，可以作为显示屏使用，硬件测试程序见：六、程序
四、程序分析
本次实验采用查询方式编写程序，程序结构流程图如图5所示
图5 程序流程图
当程序开始运行的时候，首先就是要对程序进行初始化，主要作用就是让程序按照我们所设计的初始值去运行。

初始化之后，当显示屏旋转到接收到红外发射信号时，开始执行显示程序，有规律地点亮16个led灯。

16个led及其对应引脚如图6所示
图6 16个led及其对应引脚
一列灯16个刚好对应16*16一个汉字的一列：2个字节，所以把取模到的数据依次送到P2口和P4 P5口，这里硬件中P4 P5组成一个字节，所以显示程序如下：
for(i=0;i<16;i++) //送16列显示这里只显示一个字。

{
P2=zimo[i*2]; //送数据低位显示
P4=(zimo[i*2+1]);//送数据高位显示这里用了单片机P4 和P5口是LQFP48脚才有的IO口
P5=(zimo[i*2+1])>>4;//这里行和列都是IO口独立驱动的LED
DelayUs(200); //延时让LED亮起来每列延时的时间
P2=0XFF;
P4=P5=0XFF;
}
在什么时候送显示呢？单片机IO一判断到红外接收管接收到起点信号，就开始显示，显示完16列后等待下一次的起点信号。

这样只要电机的速度够快就会稳定的把字显示字空中了。

平面的文字显示同理。

如何让一组文字不断的移动？这就需要一个字幕计数器，旋转LED每旋转一圈，这个字幕计数器就加一，指向下一列，这样不断的刷新，感觉文字就在移动了，程序如下：
j就是字幕计数器，每转一圈j就会加1；
if(KEY==0) //红外接收管判断起始位
{
j++;
if(j>672) //根据显示的字数定义改数值672/16=42个字显示完42个字后重新开始
{
j=0 ;
}
for(i=j;i<128+j;i++) //每转一圈前进一列这里定义一圈中同时显示128/16=8个字，
{
P2=zimo[i*2]; //送数据低位显示
P4=(zimo[i*2+1]);//送数据高位显示这里用了单片机P4 和P5口是LQFP48脚才有的
P5=(zimo[i*2+1])>>4;//这里行和列都是IO口独立驱动的LED
DelayUs(200); //延时让LED亮起来每列延时的时间
P2=0XFF;
P4=P5=0XFF;
}
这样，利用查询法，执行显示程序，便能在显示屏上显示预设的文字或者图形了。

五、实验结果：
我们把程序下载进单片机，接通电源，旋转屏便能显示我们预设好的图形和文字了。

本次实验先显示几个图形，然后滚动显示“郑州大学信息工程学院”几个字。

显示效果如图7所示
图7 实验显示效果
六、程序
硬件测试程序：
#include<stc89c51rc.h>
#define uchar unsigned char
#define uint unsigned int
unsigned char temp=0X0; //4个字节数据组合成一个long型数据方便移位流水测试
uchar count_time=0;
uchar i=0;
uchar j=0;
uchar u=0;
/**************************延时***********************/
//void delay(void) //误差0us
//{
// unsigned char a,b,c;
// for(c=1;c>0;c--)
// for(b=38;b>0;b--)
// for(a=130;a>0;a--);
//}
void Timer0Interrupt(void) interrupt 1
{
TH0 = 0x10; //18.432M 40MS 定时
TL0 = 0x00;
/************************************/
if(++count_time>2) //定时80MS
{
count_time=0;
temp=temp<<1;
if(++i>8)
{
i=0;
temp=0X01;
}
P2=temp;
P0=temp;
}
}
/********************************************/
/*主函数*/
void main()
{
TMOD = 0x01; //方式0
TH0 = 0x10;
TL0 = 0x00; //18.432M 40MS 定时
EA = 1;
ET0 = 1;
TR0 = 1;
// Send_data(0x55); //发一字节数据到串口
while(1)
{
}
}
实验程序（显示图形及文字）：
#include "NEW_8051.H"
#define uchar unsigned char
#define uint unsigned int //宏定义
sbit KEY=P3^2; //红外检测起点
//pc2002 设置阳码逐列顺向取模见设置图片
uchar code zimo[]={
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0x FF,0xFF,
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0x FF,0xFF,
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0x FF,0xFF,
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0x FF,0xFF,
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0x FF,0xFF,
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0x FF,0xFF,
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0x FF,0xFF,
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0x
0xFF,0xFF,0xFF,0xFF,0x3F,0xF0,0xCF,0xE3,0xF7,0xCF,0xD7,0xDF,0x19,0xBF,0x BE,0xBE,
0x3E,0xBD,0x3E,0xBD,0xBE,0xBE,0x19,0xBF,0xD7,0xBC,0x7B,0x9B,0x7B,0x08, 0x7B,0x6B,
0x7B,0x08,0x7B,0x9B,0xD7,0xBC,0x19,0xBF,0xBE,0xBE,0x3E,0xBD,0x3E,0xBD, 0xBE,0xBE,
0x19,0xBF,0xD7,0xDF,0xF7,0xCF,0xCF,0xE3,0x3F,0xF0,0xFF,0xFF,0xFF,0xFF,0x FF,0xFF,
0xFF,0xFF,0x3F,0xF0,0x0F,0xE0,0x07,0xC0,0x67,0x80,0x31,0x00,0x18,0x00,0x18, 0x00,
0x18,0x08,0x10,0x18,0x21,0x13,0x87,0x24,0x83,0x66,0x83,0x66,0x83,0x64,0x83,0 x66,
0x83,0x66,0x87,0x24,0x21,0x13,0x10,0x18,0x18,0x08,0x18,0x00,0x18,0x00,0x31,0 x00,
0x67,0x80,0x07,0xC0,0x0F,0xE0,0x3F,0xF0,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xF F,0xFF,
0xFF,0xFF,0xFF,0xFF,0x3F,0xF0,0x0F,0xE0,0x67,0xC0,0x97,0x80,0x11,0x01,0x20 ,0x02,
0x10,0x01,0x90,0x10,0x60,0x30,0x01,0x27,0xB7,0x68,0xB3,0x4E,0xB3,0xCE,0xB 3,0xC8,
0xB3,0x4E,0xB3,0x6E,0xB7,0x28,0x01,0x37,0x60,0x10,0x90,0x00,0x10,0x01,0x20, 0x02,
0x11,0x81,0x97,0xC0,0x67,0xE0,0x0F,0xE0,0x3F,0xF0,0xFF,0xFF,0xFF,0xFF,0xF
0xFE,0xFF,0xFF,0xFF,0xFF,0xFF,0x3F,0xF0,0x8F,0xE7,0xE7,0xCF,0xF7,0x9F,0x 39,0x3F,
0x3E,0x7F,0x3E,0x7F,0x3E,0x7F,0x3E,0x7F,0x39,0x63,0x37,0x5D,0xF3,0x45,0xF B,0x45,
0xFB,0x5D,0xFB,0x45,0xF3,0x45,0x37,0x5D,0x39,0x63,0x3E,0x7F,0x3E,0x7F,0x3 E,0x7F,
0x3E,0x7F,0x39,0x3F,0xF7,0x9F,0xE7,0xCF,0x8F,0xE7,0x3F,0xF0,0xFF,0xFF,0xF F,0xFF,
0x7F,0xBF,0x77,0xDF,0x76,0xEF,0x71,0xF3,0x07,0xFC,0x73,0xFB,0x74,0xF7,0x7 7,0xCF,
0x7F,0xBF,0x77,0xDF,0x76,0xEF,0x71,0xF3,0x07,0xFC,0x73,0xFB,0x74,0xF7,0x7 7,0xCF,
0x7F,0xBF,0x77,0xDF,0x76,0xEF,0x71,0xF3,0x07,0xFC,0x73,0xFB,0x74,0xF7,0x7 7,0xCF,
0x7F,0xFF,0xFF,0xFF,0x01,0x00,0xFD,0xF7,0xDD,0xEF,0x25,0xF7,0xF9,0xF8,0x FF,0xFF,/*"郑",0*/
0xFF,0x7E,0x1F,0xBF,0xFF,0xCF,0x00,0xF0,0xFF,0xFF,0xDF,0xFF,0x3F,0xFF,0x FF,0xFF,
0x01,0xC0,0xFF,0xFF,0xDF,0xFF,0x3F,0xFF,0xFF,0xFF,0x00,0x00,0xFF,0xFF,0x FF,0xFF,/*"州",1*/
0xDF,0x7F,0xDF,0x7F,0xDF,0xBF,0xDF,0xDF,0xDF,0xEF,0xDF,0xF3,0xDF,0xFC, 0x00,0xFF,
0xDF,0xFC,0xDF,0xF3,0xDF,0xEF,0xDF,0xDF,0xDF,0xBF,0xDF,0x7F,0xDF,0x7F,
0xBF,0xFB,0xCF,0xFB,0xEE,0xFB,0x69,0xFB,0x6F,0xFB,0x6F,0xBB,0x6E,0x7B, 0x69,0x81,
0x6F,0xF9,0x6F,0xFA,0x67,0xFB,0xEB,0xFB,0xEC,0xFB,0xAF,0xFB,0xCF,0xFB, 0xFF,0xFF,/*"学",3*/
0xFF,0xFE,0x7F,0xFF,0x9F,0xFF,0x07,0x00,0xF8,0xFF,0xFF,0xFF,0xFB,0xFF,0x DB,0x06,
0xDB,0xB6,0xDA,0xB6,0xD9,0xB6,0xDB,0xB6,0xDB,0xB6,0xDB,0x06,0xFB,0xF F,0xFF,0xFF,/*"信",4*/
0xFF,0xBF,0xFF,0xCF,0xFF,0xFF,0x03,0xFC,0xAB,0xC6,0xAB,0xBE,0xA9,0xBE ,0xAA,0xBA,
0xAB,0xA6,0xAB,0xBE,0xAB,0xBE,0x03,0x8C,0xFF,0xFF,0xFF,0xF7,0xFF,0xCF ,0xFF,0xFF,/*"息",5*/
0xFF,0xDF,0xFB,0xDF,0xFB,0xDF,0xFB,0xDF,0xFB,0xDF,0xFB,0xDF,0xFB,0xD F,0x03,0xC0,
0xFB,0xDF,0xFB,0xDF,0xFB,0xDF,0xFB,0xDF,0xFB,0xDF,0xFB,0xDF,0xFF,0xD F,0xFF,0xFF,/*"工",6*/
0xDB,0xF7,0xDB,0xF9,0x5B,0xFE,0x01,0x00,0xDC,0xFE,0xDD,0xF9,0xFF,0xBF, 0xC1,0xB6,
0xDD,0xB6,0xDD,0xB6,0xDD,0x80,0xDD,0xB6,0xDD,0xB6,0xC1,0xB6,0xFF,0xB E,0xFF,0xFF,/*"程",7*/
0xBF,0xFB,0xCF,0xFB,0xEE,0xFB,0x69,0xFB,0x6F,0xFB,0x6F,0xBB,0x6E,0x7B, 0x69,0x81,
0x6F,0xF9,0x6F,0xFA,0x67,0xFB,0xEB,0xFB,0xEC,0xFB,0xAF,0xFB,0xCF,0xFB,
0xFF,0xFF,0x01,0x00,0xDD,0xFB,0xA5,0xF7,0x79,0xF8,0xEF,0x7F,0xF3,0xBE,0x DB,0xCE,
0xDB,0xF0,0xDA,0xFE,0xD9,0xFE,0xDB,0xC0,0xDB,0xBE,0xEB,0xBE,0xF3,0x8 E,0xFF,0xFF,/*"院",9*/
0xFF,0xFF,0xFF,0xFF,0x07,0xE0,0x77,0xF7,0x77,0xF7,0x77,0xF7,0x77,0xF7,0x0 0,0x80,
0x77,0x77,0x77,0x77,0x77,0x77,0x77,0x77,0x07,0x60,0xFF,0x7F,0xFF,0x0F,0xFF, 0xFF,/*"电",10*/
0x7F,0xFF,0x7D,0xFF,0x7D,0xFF,0x7D,0xFF,0x7D,0xFF,0x7D,0xBF,0x7D,0x7F,0 x1D,0x80,
0x5D,0xFF,0x6D,0xFF,0x75,0xFF,0x79,0xFF,0x7D,0xFF,0x7F,0xFF,0x7F,0xFF,0x FF,0xFF,/*"子",11*/
0xFF,0xEF,0xFF,0xEF,0xF7,0xEF,0xF7,0xEF,0xF7,0xEF,0xF7,0xEF,0xF7,0xEF,0 xF7,0xEF,
0xF7,0xEF,0xF7,0xEF,0xF7,0xEF,0xF7,0xEF,0xF7,0xEF,0xFF,0xEF,0xFF,0xEF,0 xFF,0xFF,/*"二",12*/
0x7B,0xEF,0x7B,0xCF,0x03,0xE0,0x7B,0xF7,0x7B,0x77,0xFF,0xBD,0x07,0xDE,0 xFF,0xE7,
0x00,0xF8,0xFF,0xFF,0x7B,0xDF,0x7B,0xDF,0x03,0xC0,0x7B,0xDF,0x7B,0xDF,0 xFF,0xFF,/*"班",13*/
0xFB,0xFF,0xFB,0x01,0xFB,0xFD,0xFB,0xFD,0x0B,0x85,0x6B,0xB5,0x6A,0xB5, 0x69,0xB5,
0x6B,0xB5,0x6B,0xB5,0x0B,0x85,0xFB,0xFD,0xFB,0x7D,0xFB,0x01,0xFB,0xFF,
0xFF,0xFF,0xFF,0x7E,0x7F,0x7F,0x9F,0x7F,0xE7,0xBF,0xFF,0xBF,0xFF,0xDF,0x 00,0xEC,
0xFF,0xF7,0xFF,0xFB,0xF7,0xFD,0x6F,0xFE,0xDF,0xFF,0x3F,0xFF,0xFF,0xFF,0 xFF,0xFF,/*"少",15*/
0xFB,0xFF,0xFB,0xFF,0x1B,0x00,0xDB,0xF6,0xDB,0xF6,0xDB,0xF6,0xDB,0xF6, 0x00,0x80,
0xDB,0xF6,0xDB,0xF6,0xDA,0xB6,0xD9,0x76,0x1B,0x80,0xFB,0xFF,0xFB,0xFF, 0xFF,0xFF,/*"甫",16*/
0xBF,0xFD,0xBB,0x7D,0xAB,0x7D,0xAB,0x65,0xAA,0xA9,0xA9,0xAC,0x2B,0xD D,0x83,0xDD,
0xAB,0xDD,0xA9,0xAD,0xAA,0xB1,0xAB,0xBD,0xAB,0x7D,0xBB,0xFD,0xBF,0x FD,0xFF,0xFF,/*"姜",17*/
0x7B,0xFF,0xAA,0xFF,0xD9,0xFF,0xA3,0x80,0xFB,0x2A,0xBF,0xAA,0x8B,0xAA ,0xBA,0xAA,
0x82,0xAA,0xAA,0xAA,0xBB,0x2A,0xF0,0x80,0xCB,0xFF,0xBA,0xFF,0x1B,0xFF ,0xFF,0xFF,/*"贇",18*/
0xF7,0xFF,0xF7,0x7F,0xF7,0xBF,0xF7,0xDF,0xF7,0xE7,0x07,0xF8,0x76,0xFF,0x7 1,0xFF,
0x77,0xBF,0x77,0x7F,0x77,0xBF,0x77,0xC0,0xF7,0xFF,0xF7,0xFF,0xF7,0xFF,0xF F,0xFF,/*"方",19*/
0xFF,0xBF,0xFF,0xCF,0x03,0xF0,0xFB,0x7F,0x7B,0xBF,0x7B,0xDF,0x7B,0xE7,0 x7A,0xF9,
0x09,0xFE,0x7B,0xF9,0x7B,0xE7,0x7B,0xDF,0x7B,0xBF,0x7B,0x7F,0xFB,0x7F,0
0xFF,0xBF,0xFF,0xCF,0x07,0x70,0xB7,0x9F,0xB7,0xE1,0x80,0xFD,0x55,0xFD,0x 55,0xC1,
0x35,0xBF,0xE7,0xBF,0xDF,0x9D,0xEF,0xAE,0x77,0xB7,0x99,0xB9,0xFF,0x8F,0x FF,0xFF,/*"彪",21*/
0xFF,0xFF,0xFF,0xFF,0x07,0xE0,0x77,0xF7,0x77,0xF7,0x77,0xF7,0x77,0xF7,0x0 0,0x80,
0x77,0x77,0x77,0x77,0x77,0x77,0x77,0x77,0x07,0x60,0xFF,0x7F,0xFF,0x0F,0xFF, 0xFF,/*"电",22*/
0xF7,0xFD,0xF7,0xFE,0x76,0xFF,0x11,0x00,0x67,0xFF,0xFF,0x7C,0xFF,0xBF,0x 01,0xDC,
0xFD,0xE7,0xFD,0xF9,0x0D,0xFE,0xFD,0x81,0xFD,0x7F,0x01,0x7C,0xFF,0x1F,0 xFF,0xFF,/*"视",23*/
0xFF,0x7F,0xFF,0x9F,0x01,0xE0,0xFD,0xBF,0xFD,0xDF,0x0D,0xE8,0x6D,0xBB,0 x65,0x7B,
0x69,0x83,0x6D,0xFB,0x6D,0xFB,0x0D,0xE8,0xFD,0xDF,0xFD,0xBF,0xFD,0xFF, 0xFF,0xFF,/*"原",24*/
0xFB,0xDF,0x7B,0x9F,0x7B,0xDF,0x03,0xE0,0x7B,0xEF,0x7B,0xEF,0xFF,0xBF,0 x01,0xBB,
0x6D,0xBB,0x6D,0xBB,0x01,0x80,0x6D,0xBB,0x6D,0xBB,0x01,0xBB,0xFF,0xBF, 0xFF,0xFF,/*"理",25*/
0xEF,0x7F,0xEF,0x9F,0x0E,0xE0,0x69,0xBF,0x6F,0x7F,0x6F,0x80,0xEF,0x7F,0xD 7,0x9F,
0xD8,0xE0,0xDB,0xDF,0x1B,0x80,0xDB,0xBB,0xDB,0xBB,0x1B,0xBB,0xFB,0xB
0x37,0xF7,0x47,0xE7,0x70,0xF7,0x17,0x00,0x77,0xFB,0x77,0xFB,0xBF,0xFF,0xB 7,0xFD,
0xB7,0xF4,0x17,0xED,0xA0,0xDD,0xB7,0x2D,0xB7,0xF5,0xB7,0xF9,0xBF,0xFF,0 xFF,0xFF,/*"转",27*/
0xF7,0xDF,0x07,0xC0,0xF7,0xDF,0xFF,0xDF,0xFF,0xDF,0xFF,0xDF,0xFF,0xCF,0 xFF,0xFF,/*"L",28*/
0xF7,0xDF,0x07,0xC0,0x77,0xDF,0x77,0xDF,0x17,0xDC,0xF7,0xDF,0xEF,0xE7,0 xFF,0xFF,/*"E",29*/
0xF7,0xDF,0x07,0xC0,0xF7,0xDF,0xF7,0xDF,0xF7,0xDF,0xEF,0xEF,0x1F,0xF0,0 xFF,0xFF,/*"D",30*/
0xFF,0xBF,0xFF,0xBD,0xFF,0xBB,0x01,0xA7,0x6D,0xBF,0x6D,0x80,0x6D,0xBF,0 x6D,0xBF,
0x6D,0xBF,0x6D,0x80,0x6D,0xBF,0x01,0xAF,0xFF,0xB7,0xFF,0xB9,0xFF,0xBF,0 xFF,0xFF,/*"显",31*/
0xBF,0xDF,0xBF,0xEF,0xBD,0xF7,0xBD,0xF9,0xBD,0xFF,0xBD,0xBF,0xBD,0x7F ,0x3D,0x80,
0xBD,0xFF,0xBD,0xFF,0xBD,0xFF,0xBD,0xFD,0xBD,0xFB,0xBF,0xF7,0xBF,0xC F,0xFF,0xFF,/*"示",32*/
0xFF,0xBF,0xFF,0xCF,0x01,0xF0,0xED,0xFB,0x6D,0x7B,0x4D,0x9B,0x2D,0xE0, 0x6D,0xFB,
0x6D,0xFB,0x6D,0xFB,0x2D,0x00,0x4D,0xFB,0x61,0xFB,0xFF,0xFB,0xFF,0xFF,
0xBF,0xFF,0xBF,0xFF,0xBD,0xFF,0x33,0xC0,0xFF,0x6F,0xBF,0x77,0x5F,0xBF,0x 61,0xBC,
0x7D,0xD3,0x7D,0xEF,0x7D,0xD7,0x61,0xB9,0x5F,0xBE,0xDF,0x7F,0xDF,0x7F,0 xFF,0xFF,/*"设",34*/
0xBF,0xFF,0xBF,0xFF,0xBD,0xFF,0x33,0x80,0xFF,0xDF,0xBF,0xEF,0xBF,0xFF,0 xBF,0xFF,
0xBF,0xFF,0x00,0x00,0xBF,0xFF,0xBF,0xFF,0xBF,0xFF,0xBF,0xFF,0xBF,0xFF,0x FF,0xFF,/*"计",35*/
0xFF,0xF7,0xFF,0xF7,0x1F,0xF7,0x60,0xF7,0x77,0xF7,0x77,0xF7,0x77,0xF7,0x77 ,0xF7,
0x77,0xF7,0x77,0xB7,0x77,0x7F,0x77,0xBF,0x77,0xC0,0xF7,0xFF,0xFF,0xFF,0xF F,0xFF,/*"与",36*/
0xEF,0xFB,0x9F,0xFB,0xFD,0x81,0x73,0xFE,0xFF,0x7F,0x01,0xB8,0xFD,0xCF,0 x0D,0xF0,
0xFD,0xEF,0x01,0xD8,0xFF,0xFF,0x07,0xB8,0xFF,0x7F,0x00,0x80,0xFF,0xFF,0x FF,0xFF,/*"测",37*/
0xBF,0xFF,0xBF,0xFF,0xBD,0xFF,0x33,0xC0,0xFF,0xEF,0x6F,0xD7,0x6F,0x9F,0x 6F,0xC0,
0x6F,0xEF,0x6F,0xEF,0x00,0xFE,0xEF,0xF1,0xEE,0xCF,0xE9,0xBF,0xEF,0x0F,0 xFF,0xFF,/*"试",38*/
0xEF,0xFB,0xF3,0x7B,0xFB,0x7B,0x7B,0xBB,0xEB,0xB8,0x9B,0xDB,0xFA,0xEB ,0xF9,0xF3,
0x0B,0xF8,0xFB,0xF3,0xFB,0xEB,0xFB,0xDB,0xFB,0xBB,0xEB,0x7B,0xF3,0xF
0xFD,0xF7,0x05,0xE7,0x7D,0xB7,0x7D,0x7B,0x01,0xBB,0x7F,0xC0,0xBF,0xBF,0 xDF,0xBB,
0xAF,0xA7,0xB3,0xBE,0xBC,0xB1,0xB3,0x9F,0xAF,0xA7,0xDF,0xB8,0xBF,0xBF, 0xFF,0xFF,/*"验",40*/ ，，
};
/*****n（us）延时子程序*****/
void DelayUs(uint N)
{
uint x ;
for(x=0;x<=N;x++);
}
/*****主函数*****/
void main(void)
{
uint i=0,j=0 ;
// led1=0 ;
//主程序中只检测按键
while(1)
{
if(KEY==0) //红外接收管判断起始位
{
j++;
if(j>704) //根据显示的字数定义改数值704/16=44个字显示完44个字后重新开始
{
j=0 ;
}
for(i=j;i<176+j;i++) //每转一圈前进一列这里定义一圈中同时显示176/16=10个字，
{ //在这个程序中如果此参数设置过大会造成头吃尾的后果，如果过少盲点又会太大
//所以比较麻烦要根据电机速度来调整此参数
P2=zimo[i*2]; //送数据低位显示
P0=zimo[i*2+1];//送数据高位显示
DelayUs(20); //延时让LED亮起来每列延时的时间
P2=0XFF;
P0=0XFF;
}
}
}
}。