3M道路标线产品SPEC IN 写法

合集下载

危险品说明书-涂料

品名: 道路标线涂料（黄色）Commodity: traffic paint (yellow)主要成分：丙烯酸树脂Main component: Acrylic resin分子式: [C3H3O2R]nFormula: [C3H3O2R]n类别: 3Class: 3联合国编号: 1263UN No: 1263外观性状：黄色粘稠液体，有特殊气味Appearance & Properties: Yellow thick liquid, special odor运输储存注意事项：密闭容器运输，确保贮存环境干燥通风，远离火源。

Caution during transportation & Storage: Keep container tightly closed. Ensure the area is well ventilated. Keep away from sources of ignition.包装破或散漏时处理方法：防止排入水管或地下道。

小量泄漏或残留可使用适当的吸附物质进行吸收（比如沙、硅藻土或锯末等），其他按规定进行处置。

大量泄漏构筑围堤或挖坑收容，用泡沫覆盖，抑制蒸发。

How to handle with breakage and leakage of packing: Prevent products from getting into drains / groundwater. Smaller quantity leaking or residues, could contain with absorbent material (e.g. sand, diatomaceous earth, or sawdust). Dispose of in accordance with regulations. Large quantity leaking: build a coffercom or dig a pit, cover with foam to inhibit evaporation.急救措施：如果皮肤、眼睛接触产品，及时用大量清水进行清洗，如有明显不适或症状发生，应及就医治疗；如果吸入或误食，要立即移到新鲜空气处，保持冷静并及时就医进行相关治疗。

3M使用手册

3Scotch-Grip TMIndustrial Adhesive4799Features•Quick drying with fast strength buildup.•Provides low soak in on most porous substrates.•Dries to a flexible, water resistant bond.•Can be used to bond most EPDM rubber, sponge rubber, rubber sheeting, felt, canvas,linoleum and other lightweight materials to many metals, woods, concrete and many plastics.Handling/Application Information D irections for Use1.Surface Preparation: Surfaces to be bonded must be clean, dry and dust free. Wiping withsolvent such as Scotch-Grip TM Solvent No. 3 will aid in removing oil and dirt.*2.Application Temperature: For best results the temperature of the adhesive and thesurfaces being bonded must be at least 65°F (18°C).3.Application: Stir or agitate well before using.Porous Surface(s): Brush a uniform, generous coat of adhesive on the least poroussurface to be bonded. Assemble the materials immediately with sufficient pressure toensure contact.Non-Porous Surface(s): Apply a uniform coat of adhesive to each surface. Allowadhesive to dry until it is tacky, but does not transfer. Assemble materials withsufficient pressure to ensure contact.4.Cleanup: Excess adhesive may be removed with solvent such as Scotch-Grip TM SolventNo. 2.**Note:When using solvents, extinguish all sources of ignition in the area and follow the manufacturer’s precautions and directions for use when handling such materials.(Supersedes June, 1995)Typical Physical Properties Note:The following technical information and data should be considered representative or typical only and should not be used for specification purposes.Viscosity (approx.)7,500-18,000 cps.Brookfield Viscometer RVF #6 sp. @ 20 rpmSolids (by wt.)28-35%Base SBRColor BlackNet Weight (approx.) 6.6 - 7.0 lbs./gal.Flash Point (closed cup)-14°F (-26°C)Solvent Petroleum Distillate, n-hexane and toluene Note:Appropriate application equipment can enhance adhesive performance. The user is responsible for evaluating application equipment in light of the user’sparticular purpose and method of application.1.Pumping: Use a 5:1 ratio double acting, ball check pump with a 3 inch diameter air motor.All packings and glands in contact with the adhesive should be Teflon®coated.2.Hoses: Material hoses should be nylon lined with a working pressure of 500 psi or greater.3.Brushes: Brushes designed for use with oil based paint may be used.Application Equipment SuggestionsScotch-GripTMIndustrial Adhesive 4799180°PEEL STRENGTH – Canvas/SteelTimeTest Value@ 75°F (24°C)Temp.(lbs./in. width)1 day 75°F (24°C)15.53 days 75°F (24°C)225 days 75°F (24°C)257 days 75°F (24°C)25.52 wk.75°F (24°C)27.53 wk.75°F (24°C)28after 3 wk.-30°F (-34°C)14after 3 wk.150°F (66°C)8.5after 3 wk.180°F (82°C)5Typical Adhesive Performance CharacteristicsNote:The following technical information and data should be considered representativeor typical only and should not be used for specification purposes.Storage: Store product at 60-80°F (16-27°C) for maximum storage life. Higher temperatures reduce normal storage life. Lower temperatures cause increased viscosity of a temporary nature. Rotate stock on a “first in-first out” basis.Shelf Life: When stored at the recommended conditions and kept in the original, unopened container, this product has a shelf life of 1 year from date of shipment.Storage and Shelf Life3Adhesives Division3M Center, Building 220-7E-05St. Paul, MN 55144-10001-800-364-3577 or 612-737-6501T eflon is a registered trademark of E.I. DuPont de Nemours Co.Printed in U.S.A.©3M 199778-6900-2823-4For Additional Product Safety and Health Information, See Material Safety Data Sheet, or call:Recycled Paper 40% pre-consumer 10% post-consumerT o request additional product information or to arrange for sales assistance, call toll free 1-800-362-3550.Address correspondence to: 3M Adhesives Division, 3M Center, Building 220-7E-05, St. Paul, MN 55144-1000. Our fax number is 612-733-9175. In Canada, phone: 1-800-364-3577. In Puerto Rico,phone: 1-809-750-3000. In Mexico, phone: 5-728-2180.For Additional Information 3M MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANT ABILITY OR FITNESS FOR A P ARTICULAR PURPOSE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user’s method of application. Please remember that many factors can affect the use and performance of a 3M Adhesives Division product in a particular application. The materials to be bonded with the product, the surface preparation of those materials, the product selected for use, the conditions in which the product is used, and the time and environmental conditions in which the product is expected to perform are among the many factors that can affect the use and performance of a 3M product. Given the variety of factors that can affect the use and performance of a 3M product, some of which are uniquely within the user’s knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a particular purpose and suitable for the user’s method of application.Important NoticeIf the 3M product is proved to be defective, THE EXCLUSIVE REMEDY , A T 3M’S OPTION, SHALL BE TO REFUND THE PURCHASE PRICE OF OR TO REP AIR OR REPLACE THE DEFECTIVE 3M PRODUCT . 3M shall not otherwise be liable for loss or damages, whether direct, indirect, special,incidental, or consequential, regardless of the legal theory asserted, including negligence, warranty, or strict liability.Limitation of Remedies and LiabilityThis Adhesives Division product was manufactured under a 3M quality system registered to ISO 9002standards.Refer to Product Label and Material Safety Data Sheet for Health and Safety Information before using this product.Precautionary Information。

3M Scotchcast Connector Sealing Pack 3570G-N 数据表说明

3M™ Scotchcast™ Connector Sealing Pack 3570G-NDescription The 3M™ Scotchcast™ Connector Sealing Pack 3570G-N insulates and providesprotection for electrical spring connectors against dust, soil, water, and otherenvironmental elements.Each sealing pack contains a specific amount of the two-part 3M™ Scotchcast™ EpoxyResin 3570G-N in a unique closed mixing pouch. The resin generates its own heat tocure and its compatibility with spring connectors makes this sealing pack a convenientinsulating and encapsulating resin for electrical spring connections.The 3570G-N sealing pack will accommodate one 3M™ Performance Plus WireConnector O/B+, R/Y+, T/R+,T/Y+ or one 3M™ Electrical Spring and GroundingConnector 312 or 512.Features•Thermosetting; will not melt or run once it cures•Generates its own heat to cure•Stable in applications at elevated temperatures up to 121°C•Unique closed mixing pouch for mixing the resin and encapsulating the appropriatespring connectors•Tough, excellent multi-purpose moisture sealing resinApplications •For insulating electrical spring connectors•For potting and protecting a wide variety of electrical spring connections•For protecting against dust, soil, water and other environmental elementsTypical Physical And Electrical Properties Not for specifications. Values are typical, not to be considered minimum or maximum. Properties measured at room temperature 73°F (23°C) unless otherwise stated. Physical Property (Test Method)Typical ValueUS units (metric)Color BlackDensity (ASTM D792)0.65 oz/cu in (1,13 g/cc) Hardness (ASTM D2240) 60 Shore DTensile Strength (ASTM D638)1779 psi (125 kg/cm2) Elongation (ASTM D638) 57%Glass Transition Temperature, T g (DSC)70ºF (21ºC)Maximum Exotherm (100g) (ASTM D2471-99) 140°F (60°C)Gel Time @ 73°F (23°C) (ASTM D2471-99) 8-12 minutesWeight Loss, Heat Aging (3M Method TM-451)@ 250°F (121°C)1 week 3.31%2 weeks 5.33%Adhesion to Metals (lb/in2) (3M TM456)CopperBrassSteelAluminum112.5109.25172.3564.8Adhesion to Cable Jackets (lb/in2) (3M TM457)VinylNeopreneNylonXLPE53.8112.5>26.5223.4Weight Gain (1 week, boiling water) (ASTM D471) 4.76%Electrical Property (Test Method)Typical ValueUS units (metric)Dielectric Strength (ASTM D149)435 V/mil (17.1 kV/mm) Dielectric Constant @ 60Hz(ASTM D150)73°F (23°C)194°F (90°C)2.2 pF8.9 pFDissipation Factor @ 60Hz(ASTM D150)73°F (23°C)194°F (90°C)8.8%187%Installation IMPORTANT: The 3M™ Scotchcast™ Connector Sealing Pack 3570G-N should remain sealed in the guard bag (white aluminized bag) until ready to use. In coldweather, warm closed mixing pouch to 50°F (10°C) or warmer prior to mixing. Keep in a warm area, such as truck cab or inside pocket, until ready to use.1. Thoroughly clean and dry the surface of the substrate to which the material is desired to bond.2. Remove guard bag, using cautionnot to damage inner bag.3. Grip both edges of bag at thecenter barrier (fig. 1) and wrinkleand flex the bag across thebarrier. This will weaken thebarrier.4. Squeeze the clear side of the resin, forcing the resin through the center barrier.5. Mix thoroughly to a uniformcolor by squeezing contents back and forth 25-30 times. 6. Squeeze resin to one end of bag and cut off other end. (fig. 2)7. Slowly insert connection into sealing pack until it fits snugly against the opposite end. (fig. 3)8. Wrap open end of bag with Scotch® Super 33+™ Vinyl Electrical Tape and position the taped end up until resin gels (8-12 min. @ 73°F (23° C)). (fig. 4) EHSCautionWorking around energized electrical systems may cause serious injury or death. Installation should be performed by personnel familiar with good safety practice in handling electrical equipment. De-energize and ground all electrical systems before installing product.Read all Health Hazard, Precautionary and First Aid statements found in the Material Safety Data Sheet (MSDS) and/or product label of chemicals prior to handling or use.ProductSpecificationsThe material must be supplied in a two-part plastic composite bag with a barrierseparating the epoxy from the polyol. The barrier must be capable of being broken to permit mixing the two parts without opening the bag.3M, Scotch, Super33+ and Scotchcast are trademarks of 3M Company.3Electrical Markets Division6801 River Place Blvd.Austin, TX 78726-9000 800.245.3573Fax 800.245.0329 /electrical Please recycle© 3M 2013 All rights reserved 78-8141-4501-3 Rev BEngineering/ Architectural Specifications The material must be 3M™ Scotchcast™ Epoxy Resin 3570G-N. It must be packaged in the 3M two-part plastic composite closed mixing pouch. The resin must bemixed within the closed mixing pouch simply by separating the barrier between the two parts of the bag and working the contents back and forth within the bag.Shelf Life & Storage The 3M™ Scotchcast™ Connector Sealing Pack 3570G-N has a 2-year shelf life from date of manufacture when stored under humidity controlled storage (10°C/50°F to 27°C/80°F and <75% relative humidity), provided the guard bag (white aluminized bag) remains unopened. For best results, use within one hour of opening the guard bag.Availability Please contact your local distributor; available from /electrical [Where to Buy] or call 1.800.245.3573.Important Notice All statements, technical information, and recommendations related to 3M’s products are based on informationbelieved to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you mustevaluate it and determine if it is suitable for your intended application. You assume all risks and liability associatedwith such use. Any statements related to the product, which are not contained in 3M’s current publications, or anycontrary statements contained on your purchase order, shall have no force or effect unless expressly agreed upon,in writing, by an authorized officer of 3M.Warranty; Limited Remedy; Limited Liability This product will be free from defects in material and manufacture at the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted.。

3M EMMD胶水及指示标签

3 EMMD
3
电磁波频谱
• UV 200-400 nm • 可见光 400-700 nm
3 EMMD
4
UV 光区域
UVA UVB UVC UVV
200 300
λ (nm)* 320-390 280-320 250-260 395-445
400
* EIT convention
500 nm
UVC 短波 UV 杀菌用
产品选择
Al
>120degC 固化金属,磁铁粘接
填料 SiO2
EW2020
EW2030
Start
固化温度
>80degC固化塑料,金属,磁铁粘接
有填料无

EW2050 EW2060S
3 EMMD
23
3 1-Part EG Epoxy Adhesive Application of 1-part EG epoxy adhesives
250
Total outgassing
Total Outgassing (µg/g)
200
150
100
50
0
DP-460 DP-460EG DP-4XL EG
3 EMMD
19
3 2-Part EG Epoxy Adhesive
双组分环氧胶的操作时间
• 能满足不同工艺的要求
350 300
Mixed Worklife (minutes)
• 在环境老化下减少氯离子的溢出
– DP-460 EG
•
• 降低了氯离子和有机小分子的溢出和腐蚀无硅配方可用于硬盘等特殊设备
3 EMMD
18
3 2-Part EG Epoxy Adhesive

3M 中高压电缆接线、终端和接口设备说明书

3M™ Electrical Products Medium voltage joints, terminations and cable accessories.344677810 234Ever since the installation of the first 3M ™ Cold Shrink termination in 1972, we have developed products that deliver market leading efficiencies and reliability to our customers.3M ™ Cold Shrink technology ensures that a constant radial pressure is applied to the cable. This combined with acomprehensive factory testing programme and a simple installation process makes Cold Shrink the preferred termination solution for public and private networks operators across the world.34Prepare the cable as normal and clean with 3M ™ Cable Wipes.Place the 3M ™ Cold Shrink termination body over the cable and position at the correct point on the cable.Begin to remove the inner core, allowing the termination to shrink down onto the cable.Once the inner core has been fully removed, the termination installation is complete.123M ™ Plug-In EPDM Separable ConnectorsOur easy to install range of plug-in separable connectors are moulded using high quality EPDM and meet the requirements of EN 50180 and EN 50181.FeaturesŔStraight, elbow and symmetrical and assymetrical T-plug ŔAvailable for outer cone bushings type A, B, C andC1 (250 A, 400 A, 630 A and 1250 A) ŔSimple and safe installation on a wide range of cable sizes ŔMaintenance-freeŔOne piece design, with built in capacitive test point ŔFully screened, moisture-proof connectionŔFully type tested to Cenelec HD 629.1 and IEC60502-4ŔAvailable for voltage classes 6.6/11(12)kV, 20/22(24)kV, and 19/33(36)kV53M ™ Cold Shrink Fully Integrated Quick Termination III (QTIII)This fully integrated premium cable termination offers the greatest simplicity and flexibility in our range. Our premium termination covers a wide range of cable sizes and types. This termination has a shorter adjustable tail to enable it to fit into a wide range of boxes and with fewer installation steps it means there is less room for jointer error.3M ™ Cold ShrinkPart Integrated Quick Terminations (QTII)Although this part integrated Cold Shrink termination requires additional installation steps to our Premium QTIII range it still offers additional benefits over heat shrink cable terminations, which have many more parts to install, QTIIIQTIIMoisture Blocking Mastic Integrated into termination Applied separately using Scotch ® 70 Silicone Tape Outer Insulator Very good track resistance Good track resistance Stress Control Tube Integrated into termination Integrated into termination Silicone Grease providing Stress ReliefNo – integrated mastic is enough Yes – applied separately Stress Control MasticIntegrated into terminationNo – requires silicone greaseAll 3M™ Cold Shrink cable joints include built in componentsto ensure sound insulation, stress control and adequateearth potential over the screens. The 3M™ Cold Shrinktechnology ensures constant radial pressure is exertedover the cable for the duration of the cable joint’s life.34Place the 3M™ Cold Shrink splice body onto the prepared cable, connect the cores and clean thoroughly.Thoroughly grease theconnector cable in preparationfor the splice body.Once in position, beginto remove the inner coilfrom the splice body.For extra peace of mind,the splice body positionis easily checked usingthe marked centre point.1278Place the earth copper screen stocking over the splice body. Secure with3M™ Constant Force Springs.Insulate the constant forcesprings with Scotch® 23Rubber Splicing Tape andthen overlay with Scotch®Rubber Mastic Tape 2228.Position the pre-parked3M™ Cold Shrink OuterProtection Tube over thestocking and begin to removethe inner supporting core.Continue to removethe inner core until theouter tube is fully shrunk,completing the cable joint.56 FeaturesŔPrefabricated one-piece Cold Shrink splice body with integrated semi-conductive electrode forms a faraday cage over the connector and eliminates the use oftapes or additional moulded or metallic electrodesŔFast and easy installation at temperaturesranging from -20°C to +50°C ŔSuitable for a broad range of c able type and sizes ŔPermanent radial contact pressureŔSimple assembly by pulling out the spiral coreŔMeets and exceeds the requirements of European Standard CENELEC HD 629.1 and IEC 60502-4.QS1000QS2000QSIII QS200Splice Body Type Moulded Moulded Moulded ExtrudedRange Coverage 50mm² to 400mm²50mm² to 400mm²300mm² to 630mm²50mm² to 1000mm²Voltage Class 6.6/11(12)kV20/22(24)kV to19/33(36)kV 19/33(36)kV 6.6/11(12) kV to19/33(36)kV100% Factory TestedSplice BodyYes Yes Yes No67Our EPDM elastomer caps environmentally seal and protect exposed cables ends against dirt, moisture and mechanical deterioration.FeaturesŔEasy and quick to install ŔNo tools required for installation ŔCovers a wide range of cross sections ŔHigh mechanical strengthŔWaterproof, meets the requirements of ANSI C119.1 ŔResistant to various chemicals and ozone ŔApplication temperature up to 90°COur 3M ™ Cold Shrink Abandonment Kit CSCAK Series is a temporary or permanent solution for cable abandonment. The kits consist of 3M ™ Cold Shrink End Caps, 3M ™ Cold ShrinkPre-Stretched Tube, Scotch ® 23 Self Amalgamating Insulation Tape and earth connection components.FeaturesŔQuick, simple and reliable installationŔ A temporary or permanent solution for cable abandonment ŔEnvironmental sealing and mechanical protection ŔEnsures a permanent, waterproof seal and insulation ŔAvailable for single core, copper wire screened,medium voltage cables up to 33kV ŔWaterproof, meets the requirements of ANSI C119.1 ŔResistant to various chemicals and ozone ŔApplication temperature up to 90°C8Scotch ® Super 33+ Vinyl Electrical TapeA premium grade, 0.178mm thickness, highly conformable, PVC insulating tape with aggressive adhesive and elastic backing ensures easy, moisture tight electrical and mechanical protection. Excellent electrical insulating properties to provide primary electrical insulation for joints up to 600V.FeaturesŔExcellent cold weather handlingŔResistant to UV rays, abrasion, moisture, acids, and alkalis ŔFlame retardant, to UL510 ŔTemperature range -18ºC to 105ºCScotch ® Super 88 Electrical TapePremium grade, 0.2mm thick, all weather PVC insulating tape, designed to perform continuously in very low temperatures, and is conformable for installation at -18ºC. Aggressive adhesive ensures moisture tight electrical and mechanical protection.FeaturesŔTemperature range -40ºC to 105ºC ŔExcellent abrasion and puncture resistance ŔHigh tensile and mechanical strength ŔFlame retardant, to UL510Scotch ® 23 Rubber Splicing TapeA highly conformable, self-amalgamating EPR (Ethylene Propylene Rubber) tape, ideal for insulation and moisture sealing in many applications such as bus bar connections, re-jacketing, and primary insulation up to 69kV.FeaturesŔSpecial polyester liner that willnot stick when unwinding ŔStretch up to 100% for void-free,moisture-resistant insulation ŔNon-vulcanising and shelf-stable ŔOperating temperature up to 90ºCScotch ® ElectricalSemi-Conducting Tape 13A highly conformable, semi-conducting, EPR (Ethylene Propylene Rubber) tape. Conforms easily to irregular shapes and retains itsconductivity when stretched. This tape is used for high voltage connections and provides cable shield continuation and is compatible with all solid dielectric cable insulations.FeaturesŔSemi Conducting (low resistivity) ŔWithstands temperatures up to 90°C ŔPrevents partial discharge ŔExcellent resistance to solvents,UV and moisture9Scotch ® 70 Silicone Rubber Electrical TapeHigh temperature arc and track resistant tape composed of self-fusing, inorganic silicone rubber, 0.3mm thickness. This tape provides moisture sealing on outdoor systems, transformers and terminations up to 69kV. Extremely conformable, even at very low temperatures.FeaturesŔExcellent track and arc resistance ŔHigh dielectric strength 34kV/mmŔExcellent instantaneous fusion; does not needto be held down ŔClass H material (180ºC continuous operation)Scotch ®2228 Rubber Mastic TapeA conformable self-amalgamating rubber electrical insulating and sealing tape with an EPR (Ethylene Propylene Rubber) backing coated with a strong, temperature-stable mastic adhesive. This tape is 1.65mm thick and used to insulate, pad, and seal bus bar and connections up to 1000V.FeaturesŔGood adaptability to uneven surfaces ŔHigh material thickness for quickassembly of insulations and seals ŔTemperature resistance up to 90°CŔOutstanding weather and moisture resistanceScotch ® Cable Jacket Repair Tape 2234Professional grade mastic tape designed for cablejacket repair. This tape is flexible and self-amalgamating with good moisture resistance. It has a tough,abrasion-resistant backing and is quick and easy to apply. FeaturesŔFlexible and resistant to ageingŔResistance to weathering, oil, ozone and UV ŔMoisture-resistant, flame–retardant adhesive ŔTemperature range of -30 to 90°C3M ™ Scotchfil ™Electrical Insulation PuttyA soft, pliable putty which can be wrapped, stretched or moulded around irregular shapes for quick smooth insulation build-up. Use for joint insulation for electrical conductors at temperatures up to 80°C and over-wrap with Super 33+™ or Super 88 Vinyl Electrical Tape. Also suitable for some cable repair applications.FeaturesŔSoft and pliable – simply mould with your fingers ŔPermanently elastic and age-resistant ŔSelf-amalgamatingŔTemperature range of 0ºC to 80°C10Product family Joint type Application91-AH Heat Shrink Un-armoured power cables, standard buried application 91-AHA Heat Shrink Armoured power cables, standard buried application 92-NBA ResinUn-armoured power cables, standard buried application 92-NBA-GS Resin (CMR Free)Un-armoured power cables, standard buried application 92-NA-U Resin Un-armoured power cables, hazardous area application LVI-2Resin Armoured power cables, standard buried applicationLVI-2-PTU Resin Armoured Pilot and Telecom cables, standard buried application LVI-3Resin Armoured power cables, hazardous area applicationLVI-3-IC Resin Armoured Pilot and Telecom cables, hazardous area buried application 91-AC Cold Shrink Un-armoured power cables, indoor applicationLC Cold Shrink Armoured power or pilot and telecom cables, indoor application LC-STFFCold ShrinkArmoured power or pilot and telecom cables, indoor application,fire resistant3M supply a range of locating and marking, cable cleaners, wire pulling lubricants andcable marking products to complete your work.Contact us for more details.Low voltage jointingWe have a full portfolio of low voltage inline joints, including heat shrink, cold shrink and resin joints, for a wide range of applications.Sustainability at 3M –expanding our positiveglobal impact.3M will be investing approximately $1billion over the next20 years to accelerate three new environmental goals.ŔWe have committed to being carbon neutral across ourglobal operations by 2050, achieving a 50% reductionby 2030 and 80% by 2040 (from a 2019 baseline)ŔReduce water use by 25% at our facilities by 2030,including 10% by 2022 and 20% by 2025ŔReturn higher quality water to the environmentafter use in manufacturing operationsŔCombined these two goals will reduce 3M’s wateruse by 2.5 billion gallons (approx. 9.5 billion litres)each year1112© 3M 2021. All rights reserved. 3M is a trademark of 3M Company. OMG237173.3M™ EPDM Separable Connectors 11kV EPDM Indoor Plug In - for Single Core Copper Wire Screened Cables20kV EPDM Indoor Plug In - for Single Core Copper Wire Screened Cables33kV EPDM Indoor Plug In - for Single Core Copper Wire Screened Cables3M™ Cold Shrink Termination Products 11kV Indoor Terminations – Single Core11kV Indoor Terminations - Three Core11kV Outdoor Terminations - Three Core20kV Indoor Terminations - Single Core20kV Outdoor Terminations - Single Core20kV Outdoor Terminations -Three Core33kV Indoor Terminations - Single Core33kV Outdoor Terminations - Single Core33kV Indoor / Outdoor Terminations -Three Core3M Termination Accessories Barrier Boot KitsGland Kits & Seals3M™ Cold Shrink Jointing Products 11kV Straight Joints – Single Core11kV Straight Joints – Three Core**Add your choice of outer protection module, cold shrink or resin11kV Polymeric Trifurcating Joints11kV Stop End Joints11kV Branch Joints - Single Core11kV Branch Joints - Three Core20kV Straight Joints - Single Core20kV Branch Joints - Single Core33kV Straight Joints – Single Core33kV Straight Joints - Three Core33kV Transition Trifurcating JointsUK Selection – contact your local region for variationsUnit 7 Lumley CourtDrum Industrial EstateChester-le-StreetDH2 1ANT: 0191 410 4292E:***************************.ukW: 。

3M Rigid Parts Repair Technical Data说明书

Rigid Parts Repair 08275Detailed Product Description 3M™ Rigid Parts Repair is a two-part epoxy used to repair Sheet Molded Compound (SMC), Fiberglass Reinforced Polyester (FRP), and other rigid composite plastic parts.Features • Rigid two- part epoxy• 400 ml dual-syringe cartridge system• Metered static mixingTypical Physical Properties Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes.Container400 mL dual-syringe cartridgeBase EpoxyDensity lbs/Gallon (Approx.)8.3 / 8.3Color Blue / WhiteSolids Content (Approx.)100%Consistency PasteService Temperature - °F-20° to 180°FProduct Uses For repairing rigid composite materials, such as fiberglass, SMC and carbon fiber.If reinforcing a puncture, tear, or hole, use this product on the front and back side,along with reinforcing fiberglass cloth or mat on the back side.Use with the following applicators: PN 08284 (manual) and PN08280(pneumatic).3M™ Static Mixing Nozzle: PN 08193 (6/bag), PN 08194 (50/box).For professional use only. Not intended for retail sale.3M™ Rigid Parts Repair 08275Typical Performance Properties The following times have been determined with ambient air temperature and substrate temperature @ 70°F and are considered typical values.WORK TIME:10 minutesMIX NOZZLE DWELL TIME:8 minutesSAND TIME:30 minutesCURE TIME:4 hoursPAINT TIME:30 minutesNote: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. Cure time may be reduced by the addition of heat. Maximum heat 140°F for15 minutes, allow material to cool at room temperature prior to next process step.Lap Shear, SMC966 psi ASTM D1002 / 2" per minuteLap Shear, FRP1040 psi ASTM D1002 / 2" per minute Overlap shear test method: Over lap shear test for adhesion determined in accordance with ASTM D1002. Sample dimensions 1" x 4" x .0111" with an overlap area of 1/2" x 1".- 2 -3M™ Rigid Parts Repair08275Directions for Use SURFACE PREPARATION:1. Wash surface with soap and water to remove water soluble contaminants.Follow the soap and water wash with an appropriate VOC compliantproduct for removal of surface contaminants.2. Sand the surface with a grade 60 or P80 abrasive.3. Remove dust from surface using clean, un-oiled compressed air and aclean, dry rag.Note: If using to repair Metton® plastic, be sure to use 3M™ Polyolefin AdhesionPromoter (PN 05907) before applying adhesive, to insure a good bond.PRODUCT PREPARATION:1. Insert cartridge into applicator gun.2. Remove retaining collar and plug from end of cartridge. Discard plug,save retaining collar.3. Extrude a small amount of product until both parts A and B dispenseequally. NOTE: If you choose not to use a mixing nozzle, extrude theamount of filler required, and mix by hand to a uniform color.4. Attach 3M™ Mixing Nozzle (PN 08193) to cartridge and lock in placewith retaining collar.5. Dispense a small amount of material and discard. After use, leave mixnozzle in place to seal the cartridge.GENERAL REPAIR PROCESS:1. Apply a thin coat of mixed material to the repair area using a cleanplastic spreader, making certain to completely “WET OUT” the surface.For a front side cosmetic repair immediately add additional mixedmaterial, building up the repair higher than the surrounding, undamagedarea. For a back side reinforcement repair, saturate and apply fiberglassmat or cloth to the back side of the repair area.2. Allow material to cure 30 minutes.3. For a front side cosmetic repair, shape sand with a grade P80 and finalsand with a grade 180 abrasive followed by grade 240 and/or 320. A backside reinforcement is complete and does not require sanding.4. Remove dust from surface using clean, un-oiled compressed air and aclean, dry rag. NOTE: DO NOT SOLVENT WIPE.CLEAN UP:Unmixed material may be cleaned from most surfaces with an appropriateVOC compliant product.APPLICATION WARNINGS:Once the initial cleaning steps are completed, do not solvent wipe the repairarea again.Applications 3M™ Rigid Parts Repair may be used as a cosmetic repair material as well as a reinforcement repair material on Sheet Molded Compound (SMC), Fiberglass Reinforced Polyester (FRP),Metton® and other rigid composite plastic parts.- 3 -3M™ Rigid Parts Repair08275Storage and Handling STORAGEWhen stored at the recommended conditions in original, unopened containers, thisproduct has a shelf life of at least 24 months from the date of manufacture. Store ina dry place at room temperature conditions for optimal shelf life.After use, leave mix nozzle in place to seal the cartridge.HANDLINGAvoid breathing of dust created by cutting, sanding, grinding or machining. Do noteat, drink or smoke when using this product. Wash exposed areas thoroughly withsoap and water. Keep out of the reach of children. Avoid eye contact with dust orairborne particles.Precautionary Information Before using this product, please reference Product Label and/or Safety Data Sheet for Health and Safety Information. Note: Laws controlling the acceptable amounts of Volatile Organic Compounds (VOC’s) vary by state, and in some cases by locality. For surface preparation and clean-up activities, consult federal, state and local regulations regarding use of products containing VOCs in your area. IMPORTANT NOTE: There are many factors that can affect an individual repair, so the technician and repair facility need to evaluate each specific application and repair process and determine what’s appropriate. 3M recommends referring to relevant vehicle repair and OEM guidelines prior to starting all repairs.Technical Information The technical information, recommendations and other statements contained in this document arebased upon tests or experience that 3M believes are reliable, but the accuracy or completenessof such information is not guaranteed.Product Use Many factors beyond 3M’s control and uniquely within user’s knowledge and control can affect the useand performance of a 3M product in a particular application. Given the variety of factors that can affectthe use and performance of a 3M product, user is solely responsible for evaluating the 3M product anddetermining whether it is fit for a particular purpose and suitable for user’s method of application.Warranty, Limited Remedy, and Disclaimer Unless an additional warranty is specifically stated on the applicable 3M product packaging or product literature, 3M warrants that each 3M product meets the applicable 3M product specification at the time 3M ships the product. 3M MAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY IMPLIED WARRANTY OR CONDITION ARISING OUT OF A COURSE OF DEALING, CUSTOM OR USAGE OF TRADE.If the 3M product does not conform to this warranty, then the sole and exclusive remedy is, at 3M’s option, replacement of the 3M product or refund of the purchase price.Limitation of Liability Except where prohibited by law, 3M will not be liable for any loss or damage arising from the 3M product,whether direct, indirect, special, incidental or consequential, regardless of the legal theory asserted,including warranty, contract, negligence or strict liability.Automotive Aftermarket Division3M Center, Building 223-6N-01St. Paul, MN 55144-10001-877-666-2277 (1-877-MMM-CARS)/automotiveThis is the last page 3M is a trademark of 3M Company. Printed in U.S.A.©3M 2017 P.N. 05885 (11/17)。

3M610材质报告

3M610材质报告Cellophane Film Tape610Technical InformationScotch? Cellophane Film Tape 610 is a high-performance, transparent cellophane film tape featuring a high-tack adhesive system. This tape offers excellent adhesion, dispensing and handling properties.Product Features*Cellophane Film*Rubber Resin AdhesiveProduct Advantages*Temperature Resistant*Handling Properties*Good Initial Bond*Adhesion*High TackProduct Benefits*Dimensionally Stable on the Application Up to 300°F (140°C) *Easily Dispensed, Eliminates Frustration*Excellent Holding Properties for Customer Satisfaction*Controlled Unwind for Reliable Hand Dispensing*Immediate Adhesion to a Variety of SubstratesManufacturing ConsistencyState of the art processes for film making, adhesive coating and pressure sensitive tape converting lead to the most consistent and reliable product available in the market today. Special Note:3M is aware that Scotch? Cellophane Film Tape 610has been used by some customers to test the level of adhesion of coatings to various substrates. 3M does not recommend this procedure, due to variability in pressure-sensitive film tapes, which are inherent in theirmanufacture. This slight and reasonable variability is acceptable for ordinary applications,but in our opinion, could render test data based on these characteristics invalid.Scotch? Cellophane Film Tape610ConstructionBacking:CellophaneAdhesive:Pressure Sensitive Rubber ResinColors:TransparentTypical Physical Properties(Not recommended for specification purposes)ASTM Test Method Adhesion to Steel:43 oz/inch width (47 N/100 mm width)D-3330Transverse Tensile Strength:23 lb/inch width (402 N/100 mm width)D-3759Elongation at Break:15 %D-3759Tape ThicknessBacking: 1.43 mil (0.036 mm)D-3652 Total: 2.3 mil (0.058 mm)D-3652 Available Widths Available Lengths Standard widths:1/4", 3/8", 1/2", 3/4", 1", 1-1/2", 2"72 yards, boxed only Available by Special Order:Custom widths and lengths available on request,subject to minimum order requirementsCore Size (ID):3"Technical Data: All physical properties, statements andrecommendations are based either on tests we believe to be reliable or our experience, but they are not guaranteed. 3M recommends each user determine the suitability of the product for the intended use.Warranty and Limited Remedy: THE FOLLOWING WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND ANY IMPLIED WARRANTY ARISING OUT OF A COURSE OF DEALING, CUSTOM OR USAGE OF TRADE: 3M warrants its tapes will be free from defects in material and manufacture. If a tape is proved to be defective, then the exclusive remedy, and 3M’s and seller’s sole obligation shall be, at 3M's option, to replace the quantity of the tape which is proved to be defective or to refund the purchase price.Limitation of Liability: Except where prohibited by law, 3M will not be liable for any loss or damage arising from this 3M product, whether direct, indirect, special, incidental or consequential, regardless of the legal theory asserted, including but not limited to warranty, contract, negligence or strict liability.The foregoing Warranty and Limited Remedy and Limitation of Liability may be changed only by a written agreement signed by authorized officers of 3M and seller.Packaging Systems Division3M Center, Building 230-1E-04Printed in U.S.A.St. Paul, MN 55144-1000 USA? 3M 20001- 800-722-5463。

3M SJ3572 Hook Fastener产品说明说明书

ASK A 3M EXPERTApril, 20143M™ Hook Fastener SJ3572Product Description3M™ Hook and Loop Fasteners o er advanced closure alternatives to zippers, screws, snaps, hooks andmore. They o er greater design exibility, faster product assembly, smoother and cleaner exterior surfacesand improved product performance in many applications. 3M hook and loop fasteners consist of hooks andloops which engage to form a quick fastening attachment. Simply pull the strips apart by hand to disengage.Product FeaturesThe woven nylon hook has exible, self-supporting inverted j-hooks protruding up from the backing withapproximately 300 hooks per square inch (46 hooks/square cm). The woven nylon loop has thousands of soft,pliable napped loops protruding above the backing, providing for thousands of openings and closings (cycles).Both the hook and loop are preshrunk to insure maximum dimensional stability and atness. Standard colorsavailable are black, white and beige, with several custom colors available with extended delivery times andadditional costs.SJ3572 is coated with high performance acrylic pressure sensitive adhesive which has high temperatureresistance and resistant to many environmental and chemical conditions.Commonly paired with 3M™ Loop Fastener SJ3571, this hook fastener can also engage with other 3M™ LoopFasteners.Technical Information NoteThe following technical information and data should be considered representative or typical only and should not be used for speci cation purposes. Typical Physical PropertiesThickness Test Condition2.4 mm91 mil Unmated without liner0.33 mm140 mil Mated without linerProperty: Thicknessnotes: Using 1/2" pressure foot with 34 gram weightProperty ValuesMaterial Hook- Woven NylonBacking High Performance Acrylic PSALiner Polyole n with embossed 3M logoLiner Thickness0.1 mm 4 milLiner Color ClearWeight0.057 g/cm²0.013 oz/in²Typical Performance CharacteristicsProperty Values Substrate NotesDynamic Tensile7.6 N/cm²11 lb/in²Nylon Hook to NylonLoopRun at 12 inches per minuteDynamic Shear15.2 N/cm²22 lb/in²Nylon Hook to NylonLoopRun at 12 inches per minuteCleavage Strength13.1 g/cm width7.5 lb/in width Nylon Hook to NylonLoopT-Peel Adhesion 3.5 g/cm width 2 lb/in width Nylon Hook to NylonLoopRun at 12 inches per minute90° Peel Adhesion 3.9 g/cm width 2.2 lb/in width Nylon Hook to NylonLoopRun at 12 inches per minuteCycle Life5000Nylon Hook to NylonLoop Number of closures before losing 50% of original strengthTypical Performance Characteristics (continued)Product Performance:Additional Informationnotes: This guide should assist you in determining which product will adhere best to your substrate for.Handling/Application InformationDirections for UseAttachment TechniquesThe following information is intended to assist the designer considering the use of 3M hook and loop fasteners. System product performance depends upon a number of factors, including the fastener (material, adhesive and area), application method, surface characteristics (material, texture and cleanliness), environmental conditions (moisture, ultraviolet and temperature exposure) and the time it is expected to support a given load. Because many of these factors are uniquely within the user’s knowledge and control, it is required that the user evaluate 3M products to determine whether they are t for a particular purpose and are suitable for the user’s substrates, method of application and desired end use.Rounding the corners, slightly recessing the product into the substrate, or providing raised edges around the Reclosable fastener can reduce the possibility of edge lifting and improve the overall appearance of the fastener on the nished product. Mechanically securing the corners of the fastener with rivets, staples, screws, etc. may also reduce the possibility of edge lifting, but may reduce the closure performance.The two most common techniques for attaching these 3M hook and loop fasteners to various surfaces are summarized below.Pressure Sensitive Adhesive Attachment: The use of pressure sensitive adhesives eliminates or reduces the need for sewing, solvent activation, dielectric or ultrasonic bonding or bulk adhesive bonding. This can result in simplicity, improved safety and lower installation costs. Pressure sensitive adhesive products can be applied manually or automatically using a variety of equipment choices. Contact your 3M Sales Representative to discuss automated equipment options.Surface Preparation: Highly textured surfaces may reduce the ultimate adhesion levels and care should be given to minimize the surface texture or roughness. Adhesive backed fasteners should be applied to surfaces that are clean, dry and free of oil, grease, dust, mold release agents or surface contaminants that could reduce the adhesion. It is recommended to remove any surface contaminants that may reduce adhesion by using a method suited for the type and quantity of surface contaminants present. Isopropal alcohol is a good general use solvent for cleaning contaminants from surfaces for example.In exceptional cases, especially when removing silicone mold release agents or on rough, porous surfaces, it may be necessary to lightly abrade the surface, use an adhesion promoter, or surface sealer to optimize the adhesive bond to the substrate. The selection of abrasion, priming or sealing methods will depend upon the substrates and the environmental conditions the product will be exposed to during use.Attachment Procedure: To obtain optimum bond to any surface, both the fasteners and the target surfaces should have equilibrated for a minimum of one hour at temperatures between 68°F (20°C) to 100°F (38°C) before application. The liner protecting the adhesive is removed and preferably without touching the adhesive, the fastener is applied to the substrate. Exposure of the adhesive to ambient conditions without the protective liner, before applying to the surface, should be minimized as initial adhesive tack may decrease. Flexible materials should be lying on a hard at surface so as to permit uniform adhesive contact with the surface. Use of a rubber hand roller, press platen or similar device is recommended to ensure full adhesive contact or wet- out with the substrate surface. Approximately 4.5 pounds of force per square inch, (310 grams per square centimeter) is recommended to increase adhesive contact, improving bond strength. For all adhesive applications, it is important to ensure that the edges are rolled down to reduce the chance of edge lifting.Plain backedThe plain backed 3M hook and loop fasteners are most commonly sewn into their applications. Liquid or hot melt adhesives and staples are other forms of attachment that can be utilized.Sewing: Although the selvedge edge was initially developed for stitching on, customers often nd that they get better anchorage when stitching through the 3M hook and loop portions of the fastener – this may be application dependant. The type of thread and stitch type is also best determined based on individual application, however, the fastener should be stitched on all edges for the best seam strength. Typically, special machine adjustmentsare not necessary when using our 3M hook and loop fastenersStorage and Shelf LifeShelf Life when stored in original packaging at 72°F (22°C) and 50% RH is 24 months.Family GroupReferencesISO Statement Technical Information SJ3401SJ3522SJ3523SJ3526N SJ3527N SJ3402SJ3531SJ3571SJ3572SJ3532N SJ3533N SJ3530Thickness (mm)Test Condition: Unmatedwithout liner2 2.4 3.2 2.4 3.22 3.2 3.2 2.4 2.03 3.05 2.4Thickness (mm)Test Condition: Matedwithout liner3.10.330.330.330.33 3.10.330.330.33 3.3 3.30.33Material Loop-WovenNylon Hook-WovenNylonLoop-WovenNylonHook-WovenNylonLoop-WovenNylonHook-WovenNylonLoop-WovenNylonLoop-WovenNylonHook-WovenNylonHook-WovenNylonLoop-WovenNylonHook-WovenNylonBacking NoAdhesive Sewon Plasticizerresistant acrylicPSAPlasticizerresistant acrylicPSAHighPerformance rubberbased PSAHighPerformance rubberbased PSANoAdhesiveSewonGeneralPurposerubberbasedPSAHighPerformanceAcrylicPSAHighPerformanceAcrylicPSARubberbased PSARubberbased PSAGeneralPurposerubberbasedPSALiner None Nonprintedpolyolen lm Nonprintedpolyolen lmPolyethylene withredprintingPolyethylene withredprintingNone PolypropylenePolyolen withembossed 3MlogoPolyolen withembossed 3MlogoWhitePolypropyleneWhitePolypropylenePolypropyleneLiner Thickness (mm)0.0890.0890.080.080.080.10.10.080.080.08Liner Color Clear Clear White White White Clear Clear White1. Product PageUrl: https:///3M/en_US/company-us/all-3m-products/~/3M-Hook-Fastener-SJ3572?N=5002385+3293241224&rt=rud2. Safety Data SheetUrl: https:///3M/en_US/company-us/SDS-search/results/?gsaAction=msdsSRA&msdsLocale=en_US&co=ptn&q=SJ3572This Industrial Adhesives and Tapes Division product was manufactured under a 3M quality system registered to ISO 9001: 2000 and ISO/TS 16949:2002 standards.The technical information, recommendations and other statements contained in this document are based upon tests or experience that 3M believes are reliable, but the accuracy or completeness of such information is not guaranteed.Product UseWarranty, Limited Remedy, and Disclaimer Limitation of LiabilityIndustrial Adhesives and Tapes Division 3M CenterSt. Paul, MN 55144-1000800-362-3550 Please recycle.© 3M 2018. All Rights Reserved.The brands listed above are trademarks of 3M.Many factors beyond 3M’s control and uniquely within user’s knowledge and control can a ect the use and performance of a 3M product in a particular application. Given the variety of factors that can a ect the use and performance of a 3M product, user is solely responsible for evaluating the 3M product and determining whether it is t for a particular purpose and suitable for user’s method of application.Unless an additional warranty is speci cally stated on the applicable 3M product packaging or product literature, 3M warrants that each 3M product meets the applicable 3M product speci cation at the time 3M ships the product. 3M MAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY IMPLIED WARRANTY OR CONDITION ARISING OUT OF A COURSE OF DEALING, CUSTOM OR USAGE OF TRADE. If the 3M product does not conform to this warranty, then the sole and exclusive remedy is, at 3M’s option, replacement of the 3M product or refund of the purchase price.Except where prohibited by law, 3M will not be liable for any loss or damage arising from the 3M product, whether direct, indirect, special, incidental or consequential, regardless of the legal theory asserted, including warranty, contract, negligence or strict liability.。

3M GasAlertMicroClip XL – 规格说明书

GasAlertMicroClip XL – SpecificationsThe instrument must satisfy the following:Physical SpecificationsSize (h x w x d) Physical size shall be no larger than 4.4 x 2.4 x 1.2 in. / 11.3 x 6.0 x 3.1 cmWeight Weight of instrument shall be no more than 6.7 oz. / 190 g, including aligator clip. Case Material Case material shall be rugged, impact-resistant, non-corrosive composite materialthat will prevent spark generation and shall be available in highly visible safety yellowor black.Integral Boot The instrument shall be equipped with a built-in concussion-proof boot.Vibrator Alarm The detector shall be equipped with an internal vibrator alarm for high noise areas. Handling Unit shall easily attach to pocket or belt.Carrying Attachments Unit shall be equipped with a high-tension stainless steel alligator clip.Accessories The following accessories must be available:• A manual aspirator pump with sampling hose or probe• A vehicle charger•Confined space entry kits in a hard-sided carrying case•Automatic Test and Calibration Station that shall:o Bump test and calibrate instruments in the field without requiring use of adesktop PC or laptopo Be fully portable and available in a variety of portable kit optionso Provide simultaneous management of up to 6 instrument docking moduleso Include battery and 110-240 VAC line power optionso Include software for downloading, evaluating and archiving monitoringresultsUser InterfacesDisplay Type Large alphanumeric LCD (Liquid Crystal Display) type display with simultaneous andcontinuous readouts for each gas monitored in ppm, %LEL and % v/v values, asapplicable, showing the real-time gas concentrations present.Digits not to be lessthan 0.260 in. / 6.50 mm high.Display Symbols (Icons) Gas alarm icons will clearly identify alarm type, gas hazard and alarm levelencountered, low battery condition, instrument status, safe display, stealth, andcalibration steps.Keypad/Switches One-button operation must: activate the detector; run the self-test; display alarmsetpoints; display peak gas exposures and clears them; calibrate and zero. Thereshall be no requirement to access hidden switches for any instrument operation.Monitoring CapabilityConfigurations The gas detector must be available in 1, 2, 3, or 4 gas models that continuously andsimultaneously monitor for oxygen, combustible/methane gases, hydrogen sulfide,carbon monoxide as applicable.Gases Detected and Measuring Specifications Gases Standard Measuring Range In Increments of: Hydrogen Sulfide 0-100 ppm H2S 1 ppm Carbon Monoxide 0-500 ppm CO 1 ppm Oxygen 0-30.0 % O20.1 % Methane 0-5% v/v methane 0.1% methane Combustible gases 0-100% LEL 1.0% LELSensor Type Sensors must be plug-in.Longer Life The catalytic (combustible/methane) sensor should not be affected by common sulfurcompounds, such as H2S.Instrument PowerBattery Type and Run Time Lithium-polymer rechargeable battery pack. The run time of a new instrument shall not be less than 18 hours at room temperature. The run time shall not be less than 12 hours at any time over 2 years of use in a temperature range between -4°F to +122°F (-20°C to +50°C)Rechargeable Choices A Vac (110 to 240) line charger, 12 Vdc (vehicle) charger and 12 Vdc / 24 Vdc cablemust be available.Charge Time Typical charge time for rechargeable batteries shall not be more than 6 hours perbattery.EnvironmentalTemperature Range Normal operation: -4 to +122 °F / -20 to +50 °CHumidity 0-95% RH (non-condensing) continuousIngress Protection IP 66CalibrationAutomatic Calibration Calibration must be fully automatic with Auto Zero and Auto Span functions.Instrument must advise as each automatic function takes place and when to applygas. Calibration span levels must be “User Settable”.Calibration Diagnostics Equipped with calibration diagnostics protection that ensures a valid calibration, thedetector must check the ambient air and the calibration gas. If either does not meetexpected values, the detector will refuse calibration and automatically exit theprocedure, retaining all previous values.Basic Operational FeaturesInstrument Activation One-button activation. ON function must:•Test the battery and advise condition•Display the current alarm set points•Provide a full function self-test of sensor integrity, circuitry integrity and alarmactivation•Automatically calibrate the oxygen sensor•Automatically zero H2S, CO and LEL sensors•Advise when the next calibration is due in days, or advise the number of daysoverdueInadvertent Shut-off Unit must not be able to be turned OFF accidentally and will incorporate a timed offfunction that provides audible/visual/vibration OFF indications.Peak Exposures Records peak (maximum) exposure to gases encountered and must display thereading on demand.Accumulated Exposures Records both TWA (time-weighted average) to toxic gases based on an 8-hourworkday and STEL (short-term exposure limit) to toxic gases based on a 5-15 minuteuser-selectable work period. (STEL period is adjustable.) Must display readings ondemand.Confidence Beep Confidence beep must be a user selectable option.IntelliFlash (ComplianceIntelliFlash verifies operation and compliance to both the user and supervisor. Flash)Instrument Status Advise The detector must constantly analyze and test its own operational status and providealarm advice of any malfunction.Backlight Backlight automatically illuminates the display in all alarm conditions (auto with time-out) and can be reactivated on demand with a button press.Adjustable Options The unit shall be equipped with user options for the following functions:•Adjust STEL period (5-15 minutes in 1 minute intervals)•Set calibration span levels and due date•Toggle ON/OFF: confidence beep, oxygen auto-calibration at start-up, Auto-zeroLEL, CO and H2S on start-up, latching alarms, “SAFE” display function (does notdisplay gas concentrations unless readings change), stealth mode for silentoperations, Force calibration when calibration overdue, Calibration lockout:calibration must be invoked via IR, mandatory bump test option, bump testreminder•Multi-language LCD selection in English, French, German, Portuguese andSpanish•Select combustible gases measurement: 0-100% LEL (Lower Explosive Limit) orMethane gas 0-5.0% v/v•Alarm setpoint disable (set to zero for off).•Calibration due date (1 to 365 days, or set to zero for off)•User-settable confidence beep•Individual sensor enable/disable.Auto Zero Protection Must be able to activate Auto Zero at any time. To ensure a valid Auto Zero, theinstrument will first test the ambient air for background interfering gas beforeproceeding with the Auto Zero function.Instrument AlarmsAlarms and Type Simultaneous visual display alarms, audible alarms and vibrator alarms must warn inthe event of a gas alarm condition, sensor fault or instrument status alarm.Number of Gas Alarms Must be equipped with four (4) user-settable alarm levels, including instant low,instant high, TWA (Time- weighted average) and STEL (short-term exposure limit).Also, will include an OL (over limit) alarm.Visual Alarms Instrument must be equipped with at least three flashing alarm bars easily visible frommultiple angles. The backlight must light in all alarm conditions. LCD must providepositive clear alarm advice as to which alarm level and type has been exceeded(instant LOW, instant HIGH, TWA, STEL and/or over limit).Audible Alarm Instrument must be equipped with one variable pulsed audible alarm that shall berated at 95+ dB.Vibrator Alarm Instrument must be equipped with an internal vibrator alarm for high noise areas. Alarm Set points Alarm set points must be adjustable. The current alarm set points shall be displayedeach time on start-up.Over Limit Exposure Protection For exposures above the instrument’s measuring range for the combustible sensor, the instrument will provide an over limit latching alarm that must be acknowledged.Low Battery Warning Must be equipped with low battery audible and visual alarms.DataloggingRecorded All events and occurrences.Data Storage Period With a default 15-second sampling rate interval the storage capacity will be 16 hours. Compatibility Data must be compatible for use with standard office programs, such as Excel andAccess.Event LoggingRecorded Must record the last 10 alarm events encountered. Information shall include: gasmonitored, alarm level (in ppm or %) encountered, alarm duration in minutes andseconds, time elapsed since each alarm event occurred, life remaining, andcumulative alarm time.Certifications and ApprovalsIntrinsic Safety Instrument must be certified by the following standards:•Approved by CSA to both U.S. and Canadian StandardsCAN/CSA C22.2 No. 157 and C22.2 152ANSI/UL - 913 and ANSI/ISA - 12.13.01 Part 1CSA Class I, Division 1, Group A, B, C, and D•ATEX: CE 0539 g II 1 G Ex ia IIC T4 GaSira 13ATEX2330EN 60079-0, EN 60079-11, and EN 60079-26•IECEx: Ex ia IIC T4 Ga IECEx CSA 05.0015IEC 60079-0, IEC 60079-11, IEC 60079-26•KTL 12-KB4BO-0053Manufacturing Approval The instrument must be certified compliant with ISO 9001 provisions.RFI/EMI Protection RFI/EMI protection must comply with EMC directive 2004/108/ECWarrantyWarranty Two-year full, non pro-rated warranty including instrument, sensors and battery.UK Office。

3M Scotch 盒缝胶带吊带 HR-80 HR-83 说明书

Instructions and Parts ListScotch®Box Sealing Tape DispenserHR 80 (2 inch) HR 83 (3 inch)Model 11000DescriptionThe Tape Dispenser HR 80 / HR 83 provides a quickand easy method for dispensing Scotch® Box SealingTapes directly from the roll. This lightweight, hand-held,portable dispenser is recommended for center seamsealing of RSC boxes.Box Sealing Tape Dispenser HR 80 / HR 83 Speciﬁ cationsTape:For use with most Scotch® Box Sealing Tapes.Tape Widths:HR 80 - 2 inch or 55mm maxHR 83 - 3 inch or 72mm maxTape Roll Diameter:Up to 5-1/8 inch [130mm] maximum on a 3 inch [76.2mm]diameter core.Overall Dimensions:Length: 5 3/4 inches [145mm]Height 10 inches [255mm]Width HR 80 - 2 3/4 inches [ 70mm]HR 83 - 3 3/4 inches [ 95mm]Weight Packaged 1.45 lbs. [0.65 kg]Unpackaged 1.25 lbs. [0.56 kg]Loading InstructionsFigure 1 - Place tape roll fully onto tape drum todispense tape forward from top of roll.Pull tab to remove and discard bladeprotection.Figure 2 - Pivot brake to open position. Threadtape between roller and brake.Figure 3 - Bring tape up and around roller and pullback slightly to one side to cut off excesstape. Adjustable tape roll tension provided.Operating Instructions (Figure 4)A. Place tape and applicator roller on box frontcorner (centered on top seam). Roll dispenserdown to tack tape lead end to side of box.B. P ull dispenser across box top seam applyingpressure to applicator roller in order to obtain atightseal.C. C ontinue tape web 2 1/2 to 3 inches or 65 to 75mmpast end of box.D. B ring dispenser tape wipe-down plate against thecorner of the box. Push down while slightly twistingto cut and wipe tape end to back side of boxes.12Equipment Warranty and Limited Remedy: THE FOLLOWING WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND ANY IMPLIED WARRANTY ARISING OUT OF A COURSE OF DEALING, A CUSTOM OR USAGE OF TRADE:3M warrants that its Scotch ® Box Sealing Equipment will be free from defects for ninety (90) days after delivery. If any part is proved to be defective within the warranty period, then the exclusive remedy and 3M’s and seller’s sole obligation shall be, at 3M’s option, to repair or replace the part, provided the defective part is returned immediately to 3M’s factory or an authorized service station designated by 3M. A part will be presumed to have become defective after the warranty period unless the part is received or 3M is noti ﬁ ed of the problem no later than ﬁ ve (5) calendar days after the warranty period. If 3M is unable to repair or replace the part within a reasonable time, then 3M, at its option, will replace the equipment or refund the purchase price.Limitation of Liability: 3M and seller shall not be liable for direct, indirect, special, incidental or consequential damages based upon breach of warranty, breach of contract, negligence, strict liability or any other legal theory.The foregoing Equipment Warranty and Limited Remedy and Limitation of Liability may be changed only by a written agreement signed by authorized of ﬁ cers of 3M and seller.Model Part NumberDescriptionHR 80 78-8137-3530-1 2" Blade/Wiper Assembly HR 83 78-8137-3531-9 3" Blade/Wiper AssemblyMinimum billing on parts orders is $25.00. Replacement part prices available on request. $10.00 restocking charge per invoice on returned parts.Outside the U.S., contact the local 3M subsidiary for parts ordering information.How To Order Replacement Parts1. Refer to parts list for correct part number.2. Order by description, dispenser name, andpart number.3. Replacement parts and part prices availabledirect from:How To Replace the Wiper and Blade Assembly 1. Remove screws to detach used wiper and bladeassembly.2. Install new wiper and blade assembly withserrated cutting edge pointing away from applicator roller.3. Replace and tighten screws to secure new wiperand blade assembly (Figure 5).3M Tape Dispenser Parts 241 Venture DriveAmery, WI 54001-1325800-344-9883Fax: 715-268-8153Replacement Parts List To reduce the risk associated withsharp blade hazards:Keep hands and cutoff blade. The blade is extremely sharp.Figure 5Replacement IllustrationIndustrial Adhesives and Tape Division 3M Center, Building 220-5E-06St. Paul, MN 55144-10001-800-362-3550/packaging“Scotch” is a trademark of 3M Company "3M" is a trademark of 3M Company,St. Paul, Minnesota 55144-1000Printed in U.S.A.© 3M 2011 44-0009-2199-9 (C042911-NA)。

3M汽身运用

Inner Decoration-Roof fixation Dual lock-SJ3551/3552-Tier 1 Inner Decoration Panel EC-1368Adhesives
Temporary holding on sealantcuring250/2307
Identification Laser label 7847
• In-house development • Leverage 3M Total Solution
2004-2007 Key Accounts Sales Projection
(US$’000)
800 600 400 200 0
2004 2005 2006 2007 50 5 10 5 200 100 50 20 500 200 300 100 750 300 400 150
3M Products Application in AOEM
924# ATT
丁基“蛇胶”防水胶带
6010/7533丝网印刷胶水
3M Products Application in AOEM Tier Suppliers
3M Product: SJ3550 Customer Product: Glass Box Account/Business backgrounds:
lossoflabelintransnoconformabilitynonreadabilitydiscolorlongtimecomplaintfromchannelensurecustomersuccess3mibsolutionontirelabel标签基本作用使用图例典型应用作用品牌标识及形象展示??公司形象??公司品牌展示??公司产品展示??产品使用说明??警示防伪指示建立客户忠诚度使用说明及警示提供清楚的产品使用说明及警示说明保护客户并防止篡改保护客户安全

3M 胶带产品说明书

3 Health Care 3M CanadaPost Office Box 5757 London,Ontario N6A4T1 1-800-364-3577/healthcare 3M,Scotchcast and Primacast are trademarks of 3M.Used under license in Canada.Printed in Cannada Copyright ©3M 2003. All rights reserved.0311 MS18559 E3M Immobilization Products Benefits and ApplicationsCasting Splinting Accessories3InnovationXXXXAt 3M Health Care,our full line of immobilization products are designed to offer you superb handling characteristics and reliable performance in all your immobilization applications.XX1Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Casting Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23M ™Scotchcast ™Plus Casting Tape . . . . . . . . . . . . . . . . . . . . . . . . . . . 33M ™Scotchcast ™Poly Casting Tape . . . . . . . . . . . . . . . . . . . . . . . . . . 43M ™Scotchcast ™Soft Cast Casting Tape . . . . . . . . . . . . . . . . . . . . . . . 5The Dip Application Technique . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Splinting Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73M ™Scotchcast ™Conformable Splint . . . . . . . . . . . . . . . . . . . . . . . . . 83M ™Scotchcast ™Custom Length Splint . . . . . . . . . . . . . . . . . . . . . . . 93M ™Scotchcast ™One-Step Splint . . . . . . . . . . . . . . . . . . . . . . . . . . . 103M ™Primacast ™Unpadded Splint . . . . . . . . . . . . . . . . . . . . . . . . . . . 113M ™Primacast ™Splinting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Casting Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133M ™Synthetic Cast Stockinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143M ™Canvas Cast Shoes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143M ™Splint Scissors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153M ™Synthetic Cast Padding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153M ™Reinforcing Strips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17–21XXXX 3M Casting Products2Product BenefitsWater-activated resin lets youcontrol working time according to application needs.High and early strength allows for weight bearing in 20 minutes and provides a durable cast with less chance of breakdown and the need for costly repairs or replacements. Lightweight for easy mobility. Stretches to conform well to contours for a more comfortable,better fitting cast.Porous weave allows the skinto breathe.Available in 11 colours to maximize patient satisfaction.Suggested ApplicationsFor use in the construction of orthopaedic casts.A lightweight,strong and durable casting tape that combines the benefits of a fibreglass casting tape with the handling ease of plaster. Available in 11 colours to meet patient preferences.3Casting3M ™Scotchcast ™Plus Casting Tape4Product BenefitsHighly radiolucent,lightweightand comfortable for your patients. Resilient and hard wearing as you expect from synthetic tapes. Contains no constricting elastic components.Full range of sizes available.Suggested ApplicationsFor use in the construction of orthopaedic casts.Scotchcast poly casting tape is easy to use and mould,and conforms well to body contours,thus reducing the risk ofconstriction.3M ™Scotchcast ™Poly Casting TapeProduct BenefitsFlexible,soft cast allows for mobility to accommodate specific patient requirements. Casting tape is easy to apply and remove for fast application and enhanced patient comfort. The soft,pliable cast edges improve patient comfort.Ideal for use in combination with rigid Scotchcast casting tape,as soft edges provide additional comfort.Suggested ApplicationsFor use in the construction of casts where support is needed but rigid immobilization is not required,or a limited range in motion is desired. Applications include:Sports Medicine:thumb,wrist and ankle sprains Pediatric Orthopaedics:serial casting for club foot treatmentGeneral Orthopaedics: secondary casting,hybrid casting,corsetsOccupational Therapy: removable splintsA fibreglass casting tape that does not setto a completely rigid state,but remainsflexible and soft even when it iscompletely cured.5Casting3M™Scotchcast™Soft Cast Casting Tape6Basic Dip TechniquesFor casting,select and apply the appropriate size 3M ™Synthetic Stockinet and 3M ™Synthetic Cast Padding.Then select the appropriate size roll of casting tape or splint material for your patient.Note:Gloves must be worn while handling the casting tape so resin doesn’t transfer to skin. No gloves are necessary for Scotchcast ™One-Step Splint.Immerse the roll of tape or splint material in room-temperature water (21-24°C). Give three firm squeezes of the roll or splint while it is submerged in water. For splints,blot on a towel to remove excess water. This will give a set time of approximately 3 minutes. For casting material,wrap the limb spirally and overlap by 50%. For splints,apply to the extremity with foam or felt against the skin and wrap with an elastic bandage.Mould and finish the cast or splint as desired. In areas of critical moulding,keep your hands in place for 30 seconds to speed setting.Specialty Dip TechniquesTo shorten set time,use warmer water and squeeze the roll. If the roll orsplint is immersed in water above 27°C,the roll will set more quickly and a slight increase in the amount of heat release may be noted.To lengthen the set time to about four minutes,immerse the roll or splint in cooler water and remove it immediately without squeezing.(If the casting material is not squeezed while submerged in water,there may be a decrease in slipperiness of the tape.)If maximum set time is desired,don’t dip the roll or splint at all. When you are ready to mould,you can use a spray bottle to moisten the cast or splint or simply dip your gloved hand in water. Do not moisten splint after it is wrapped.Note:Set Strength vs Functional StrengthCast or Splint moulding should be performed until materials set,approximately three minutes after activated in water. Cast material will continue to harden until it reaches functional strength,about 20 minutes from the time it’s activated in water.The Dip Application TechniqueXXXX773M Splinting ProductsSplintingProduct BenefitsLow-profile,one-sided felt padding is less bulky so it moulds more easily to the patient for a closer,more conformable fit.All-in-one splint allows for easyapplication and time savings.Faster application increases patient turnaround. Hypoallergenic,water-repellent felt padding dries much more quickly than standard padding.Provides strong,lightweight support in minutes toencourage early patient mobility.Less messy than plaster splintsfor easy application and faster cleanup.Suggested ApplicationsFor use in the construction of common orthopaedic splints.A ready-to-use,highly conformable splint made of layered fibreglass and pre-padded with water-repellent felt forquicker drying. Pre-packaged in a varietyof sizes to meet application needs.3M ™Scotchcast ™Conformable SplintProduct BenefitsSplint can be customized andcut to the exact length needed for less waste and cost-effective product use.Easy-to-use,self-sealing dispenser helps ensure freshness of splinting material.All-in-one splint allows foreasy application and time savings.Faster application increases patient turnaround.Provides strong,lightweight support in minutes toencourage early patient mobility.Hypoallergenic,water-repellent felt padding dries much more quickly than standard padding.Suggested ApplicationsFor use in the constructionof common orthopaedic splints. Ideal for high volume users such as emergency departments.A cut-to-length fibreglass splinting material that is packaged in an easy-to-use,self-sealing system. The splinting material is made of layered fibreglass andis pre-padded with water-repellent felt.Splinting3M ™Scotchcast ™Custom Length SplintProduct BenefitsAll-in-one splint allows for easy application and time savings.Faster application increases patient turnaround.Conformable and mouldable forbetter patient fit.Provides strong,lightweightsupport to encourage early patient mobility.Available in a variety of pre-cut sizes to accommodate a variety of patient sizes and reduce the need to cut and customize splints.Suggested ApplicationsFor use in the construction of common orthopaedic splints.A splint that incorporates foam padding,splint and breathable backing for easy,one-step application. Pre-packaged in avariety of sizes to meet application needs.3M ™Scotchcast ™One-Step SplintProduct BenefitsOffers the speed and strengthyou expect in synthetics,with a water-activated material that sets in approximately 3-4 minutes with adequate functional strength. Provides a plaster-like conformability for easy moulding and patient fit.Provides superior radiolucency for easier diagnosis from X-rays. Unpadded,for easy customization.Suggested ApplicationsFor use in the construction of common orthopaedic splints.A revolutionary splint technology that offers the speed and strength users expect from synthetic splints with the conformability and feel of plaster.Available unpadded in a variety of sizesto meet patient treatment needs.Splinting3M ™Primacast ™Unpadded SplintAccessories 3M Casting AccessoriesEssential component of a high-quality cast,this synthetic stockinet is intended for use as an underlayment for all standard casting applications. Suitable for use with all casting materials,plaster and synthetic.Product BenefitsStockinet helps reduce water retention and improves patient comfort.Can be used for all standard casting applications and with all casting materials for greater versatility.Available in a variety of widths to meet your casting needs.100% knitted polyester stockinet provides conformability for easy use.Suggested ApplicationsFor use as an underlayment for all standard casting applications.Product BenefitsCanvas shoe design improves the patient’s gait.Protects the cast to reduce need for repair and replacement.Available in a variety of sizes to meet patient needs.Suggested ApplicationsProtecting walking casts that do not have a walking heel attached.A canvas cast shoe designed to improve the patient’s gait while it protects the cast.The shoes are open at the toe and heel,and are available in light beige in a range of sizes.3M ™Synthetic Cast Stockinet3M ™Canvas Cast ShoesAccessories Product BenefitsDesigned for easy and precisecutting of Scotchcast customlength splints.Durable for long-lasting use.Suggested ApplicationsCutting Scotchcast custom lengthsplints.Trimming other 3M splintingmaterials.A pair of scissors designed for use with3M™Scotchcast™Custom Length Splintsor for trimming other 3M splintingmaterials.Product BenefitsSpun polyester padding providesprotection and patient comfort,while helping reduce waterretention for a drier cast.Strong and durable padding iseasy to tear.Conforms easily to body contours.Porous to allow the skin tobreathe.Versatile padding can be used withall casting materials,plaster andsynthetic.Available in a variety of widths tomeet your casting needs.Suggested ApplicationsPadding under casts.A non-woven polyester padding that isporous,highly conformable,strong,yeteasy to tear. Suitable for use with allcasting materials.3M™SplintScissors3M™Synthetic Cast PaddingA reinforcing strip designed to aid in creating strong and durable fibreglass casts,particularly those likely to be exposed to significant challenges of breakdown or stress.Product BenefitsReinforcing strips are easyto use for fast reinforcement of high stress casts.Provide strength and stability to improve cast durability and wear.Wide weave fibreglass mesh allows the cast to breathe better than with closed weave splints for cooler,lighter casts.Suggested ApplicationsReinforcing fibreglass casts,especially those likely to be exposed to significant challenges of breakdown or stress.3M ™Reinforced StripsOrdering Information Ordering Information3M™Scotchcast™Plus Casting TapeCat.No.Description Size Rolls/Case 82001White1" x 2 yds. (2,5 cm x 1,8 m)10 82002White2" x 4 yds. (5 cm x 3,6 m)10 82003White3" x 4 yds. (7,5 cm x 3,6 m)10 82004White4" x 4 yds. (10 cm x 3,6 m)10 82005White5" x 4 yds. (12,5 cm x 3,6 m)10 82002A Black2" x 4 yds. (5 cm x 3,6 m)10 82003A Black3" x 4 yds. (7,5 cm x 3,6 m) 10 82004A Black4" x 4 yds. (10 cm x 3,6 m)10 82005A Black5" x 4 yds. (12,5 cm x 3,6 m)10 82002B Blue2" x 4 yds. (5 cm x 3,6 m)10 82003B Blue3" x 4 yds. (7,5 cm x 3,6 m)10 82004B Blue4" x 4 yds. (10 cm x 3,6 m)10 82005B Blue5" x 4 yds. (12,5 cm x 3,6 m)10 82002G Green2" x 4 yds. (5 cm x 3,6 m)10 82003G Green3" x 4 yds. (7,5 cm x 3,6 m)10 82004G Green4" x 4 yds. (10 cm x 3,6 m)10 82005G Green5" x 4 yds. (12,5 cm x 3,6 m)10 82002J Glow-in-the-dark2" x 4 yds. (5 cm x 3,6 m)10 82003J Glow-in-the-dark3" x 4 yds. (7,5 cm x 3,6 m)10 82004J Glow-in-the-dark4" x 4 yds.(10 cm x 3,6 m)10 82002L Light Blue2" x 4 yds. (5 cm x 3,6 m)10 82003L Light Blue3" x 4 yds. (7,5 cm x 3,6 m)10 82004L Light Blue4" x 4 yds.(10 cm x 3,6 m)10 82005L Light Blue5" x 4 yds. (12,5 cm x 3,6 m)10 82002R Red2" x 4 yds.(5 cm x 3,6 m) 10 82003R Red3" x 4 yds. (7,5 cm x 3,6 m)10 82004R Red4" x 4 yds.(10 cm x 3,6 m) 10 82005R Red5" x 4 yds.(12,5 cm x 3,6 m) 10 82002U Purple2" x 4 yds. (5 cm x 3,6 m)10 82003U Purple3" x 4 yds.(7,5 cm x 3,6 m) 10 82004U Purple4" x 4 yds. (10 cm x 3,6 m)10 82005U Purple5" x 4 yds. (12,5 cm x 3,6 m)10 82002V Bright Green2" x 4 yds. (5 cm x 3,6 m)10 82003V Bright Green3" x 4 yds. (7,5 cm x 3,6 m)10 82004V Bright Green4" x 4 yds. (10 cm x 3,6 m)10 82002W Bright Orange2" x 4 yds. (5 cm x 3,6 m)10 82003W Bright Orange3" x 4 yds. (7,5 cm x 3,6 m)10 82004W Bright Orange4" x 4 yds. (10 cm x 3,6 m)10 82002X Bright Pink2" x 4 yds. (5 cm x 3,6 m)10 82003X Bright Pink3" x 4 yds. (7,5 cm x 3,6 m)10 82004X Bright Pink4" x 4 yds. (10 cm x 3,6 m)10 82005X Bright Pink5" x 4 yds. (12,5 cm x 3,6 m)10Ordering Information3M™Scotchcast™Poly Casting TapeCat.No.Description Size (width)(unstretched length)(stretched length)Rolls/Case86001White1" (2,5 cm) 1.75 yds. (1,6 m) 2.3 yds. (2,1 m)1086002White2" (5,0 cm) 3.5 yds. (3,2 m) 4.5 yds. (4,1 m)1086002R Red2" (5,0 cm) 3.5 yds. (3,2 m) 4.5 yds. (4,1 m)1086002U Purple2" (5,0 cm) 3.5 yds. (3,2 m) 4.5 yds. (4,1 m)1086002B Blue2" (5,0 cm) 3.5 yds. (3,2 m) 4.5 yds. (4,1 m)1086003White3" (7,5 cm) 3.5 yds. (3,2 m) 4.5 yds. (4,1 m)1086003R Red3" (7,5 cm) 3.5 yds. (3,2 m) 4.5 yds. (4,1 m)1086003U Purple3" (7,5 cm) 3.5 yds. (3,2 m) 4.5 yds. (4,1 m)1086003B Blue3" (7,5 cm) 3.5 yds. (3,2 m) 4.5 yds. (4,1 m)1086004White4" (10,1 cm) 3.5 yds. (3,2 m) 4.5 yds. (4,1 m)1086004R Red4" (10,1 cm) 3.5 yds. (3,2 m) 4.5 yds. (4,1 m)1086004U Purple4" (10,1 cm) 3.5 yds. (3,2 m) 4.5 yds. (4,1 m)1086004B Blue4" (10,1 cm) 3.5 yds. (3,2 m) 4.5 yds. (4,1 m)1086005White5" (12,7 cm) 3.5 yds. (3,2 m) 4.5 yds. (4,1 m)1086005R Red5" (12,7 cm) 3.5 yds. (3,2 m) 4.5 yds. (4,1 m)1086005U Purple5" (12,7 cm) 3.5 yds. (3,2 m) 4.5 yds. (4,1 m)1086005B Blue5" (12,7 cm) 3.5 yds. (3,2 m) 4.5 yds. (4,1 m)103M™Scotchcast™Soft Cast Casting TapeCat.No.Description Size Rolls/Case82101White1" x 2 yds. (2,5 cm x 1,8 m)1082102White2" x 4 yds. (5 cm x 3,6 m)1082103White3" x 4 yds. (7,5 cm x 3,6 m)1082104White4" x 4 yds. (10 cm x 3,6 m)1082105White5" x 4 yds. (12,5 cm x 3,6 m)103M™Scotchcast™Conformable SplintCat.No.Size Each/Case 722102" x 10"(5 cm x 25,4 cm)10 723123" x 12"(7,5 cm x 30,5 cm)10 723353" x 35" (7,5 cm x 88,9 cm)10 724154" x 15"(10,2 cm x 38,1 cm)10 724304" x 30" (10,2 cm x 76,2 cm)10 725305" x 30" (12,7 cm x 76,2 cm)103M™Scotchcast™Custom Length Splint (CLS)Cat.No.Description Size Each/Case 760022" CLS2" x 15' roll (5 cm x 457 cm)1 76002D2" CLS Door 6" x 6-1/2"1 760033" CLS3" x 15' roll (7,5 cm x 457 cm)1 76003D3" CLS Door7" x 6-1/2"1 760044" CLS4" x 15' roll (10 cm x 457 cm)1 76004D4" CLS Door8" x 6-1/2"1 760055" CLS5" x 15' roll (12,5 cm x 457 cm)1 76005D5" CLS Door9-1/2" x 6-1/2"13M™Scotchcast™One-Step SplintCat.No.Size Each/Case 76210A2" x 10" (5 cm x 25 cm)10 76312A3" x 12" (7,5 cm x 30 cm)10 76415A4" x 15" (10 cm x 37,5 cm)10 764304" x 30" (10 cm x 75 cm)10 765305" x 30" (12,5 cm x 75 cm)10 863353" x 35" (7,5 cm x 87,5 cm)10 865455" x 45" (12,5 cm x 112,5 cm)103M™Primacast™Unpadded SplintCat.No.Size Each/Case 302102" x 10" (5 cm x 25,4 cm)15 303123" x 12" (7,5 cm x 30,5 cm)15 303353" x 35" (7,5 cm x 88,9 cm)15 304154" x 15" (10,1 cm x 38,1 cm)15 304304" x 30" (10,1 cm x 76,2 cm)15 305305" x 30" (12,7 cm x 76,2 cm)10 305455" x 45" (12,7 cm x 1,1 m)10 306306" x 30" (15,2 cm x 76,2 cm)10 306456" x 45" (15,2 cm x 1,1 m)10 308308" x 30" (20,3 cm x 76,2 cm)10 308458" x 45" (20,3 cm x 1,1 m)10Ordering Information3M ™Synthetic Cast PaddingCat.No.Size Each/BagBags/CaseCMW022" x 4 yds. (5 cm x 3,6 m)204CMW033" x 4 yds. (7,5 cm x 3,6 m)204CMW044" x 4 yds. (10 cm x 3,6 m)204CMW066" x 4 yds.(15 cm x 3,6 m)2043M ™Canvas Cast ShoesCat.No.Description Size Each/Case73040D Infant –673041D Very Small 1, 2, 3673061Small 4, 5, 6373062Medium 6, 7, 8373063Large8, 9, 1033M ™Splint ScissorsCat.No.Each/Case74002103M ™Reinforcing StripsCat.No.Size Each/Case709414" x 18" 10709434" x 36"103M ™Synthetic Cast StockinetCat.No.Size Each/CaseMS011" x 25 yds. (2,5 cm x 22,8 m)1MS022" x 25 yds. (5 cm x 22,8 m)1MS033" x 25 yds. (7,5 cm x 22,8 m)1MS044" x 25 yds. (10,1 cm x 22,8 m)1MS066" x 25 yds. (15,2 cm x 22,8 m)1MS088" x 25 yds.(20,3 cm x 22,8 m)1For more informationFor additional information contact your 3M Health Care Sales Representative,or call the 3M Health Care Customer Helpline at 1-800-364-3577, or visit our web site at /healthcare.。

3M 检验标准

3Optical Systems Division (OSD) Specialty Display ProductsCustomer Quality SpecificationAnti-Reflection Matte Removable (ARMR220 NC) Protection Film Sheet Product Format3Optical Systems Division (OSD)Specialty Display ProductsCustomer Quality SpecificationAnti-Reflection Matte Removable (ARMR220 NC)Protection FilmTable of Contents1.0 Scope2.0 Function3.0 Material4.0 Structure5.0 Optical Definitions6.0 Optical Characteristics7.0 Appearance8.0 Measurement9.0 Environmental Testing10.0 Patent11.0 Packaging12.0 Warranty Period and Storage Conditions1.0 ScopeThis document provides customer specifications for anti-reflection matte removable ARMR220 NC Protection Film.2.0 FunctionARMR220 NC is an anti-reflection film with a removable adhesive. When laminated to the front surface of electronic displays, ARMR220 NC reduces the first surface glare and protects the display from scratching and abrasion. The top surface has a anti-fingerprint layer, which allows some contaminants to be wiped off, making the surface easy to clean. ARMR220 NC is intended to be used for a period of time and replaced with a fresh piece of ARMR220 NC.3.0 MaterialARMR220 NC is a non-tacky elastomer adhesive coated onto anti-reflection film. The AR film is composed of polyester (PET) coated with a scratch resistant hardcoat on one side. The hardcoat is coated with an anti-reflective (AR) coating. The top surface is covered with a low surface energy polymer layer for easy fingerprint removal.4.0 Structure5.0 Optical Definitions5.1.1 Haze – In transmission, the scattering of light by a specimenresponsible for the reduction in contrast of objects viewed throughit. The percent of transmitted light that is scattered so that itsdirection deviates more than a specified angle (2.5°) from thedirection of the incident beam.5.1.2 Transmission – The ratio of radiant power transmitted by an objectto the incident radiant power, expressed in percent.5.1.3 Clarity – In transmission, the deviation of transmitted light fromthe incident angle by a specimen responsible for the distortion ofobjects viewed through it.5.2 Cosmetics5.2.1 Point defect: Dark or light colored, opaque, transparent ortranslucent spot. Size of defect is judged by “D” below.where D = average diameter or {(a+b)/2}5.2.2 Scratch: Any line-like defect. Size and shape defined as greaterthan 4:1 aspect ratio and a >10 mm, where “a” is defined in thedrawing above.5.2.3 Dimple/Dent/Impression: A change in the topography of the filmsurface that is visible in reflected light.5.2.4 If an anomaly causes the product to be unusable in its application,it will be considered a defect. If the anomaly is visible but doesnot affect the function or appearance of the product in its use (e.g.scratches on surface of release liner, etc.), it will not be considereda defect. Cosmetic defects in the release liners should not beconsidered as they are designed to protect the product duringshipping/handling/assembly and disposed prior to final use.6.0 Optical CharacteristicsCharacteristic SpecificationHaze < 3%Transmission > 93%Clarity > 75%7.0 Appearance7.1 InspectionThe film is inspected using reflected and transmitted light. There should be no other lights on in the inspection area. The part is positioned at the eye level of the inspector. The viewing distance from the part to the eye should be no less than 8” (200mm) and more than 18” (457mm).7.1.1 Transmitted Light Inspection:The inspection for defects in transmitted light is done by looking straightthrough the film. Inspection should be based on a display white state.7.1.2 Reflected Light Inspection:The inspection for defects in reflected light is done by positioning the film ata 30-degree angle from the inspector and looking for defects on the topsurface of the film. The light source is a light fixture that contains cool white fluorescent lamps with a light output of approximately 25-35 footcandles(250-375 Lux).7.1.3 Inspection flow:Use reflective light inspection as the preliminary judgment, and if defectscan be found then use transmitted light to judge point defect and linear defects. Defect count should be decided under same background display state(e.g.: turned on to the white mode).7.2 Defect LimitsNon-uniformities are identified using visual inspection in transmissionand reflection under typical room lighting.If an anomaly is observable but does not affect the function ofappearance of the product in its use (e.g.: scratches on the surface ofrelease liner, etc.), it will not be considered a defect.7.3 Defect Specifications7.3.1 Finished Cut – Equal to or larger than 7”Point Defects (transmitted and reflected light)Maximum Allowable Diameter/Equivalent Diameter(Using 3M Limit Gauge)> 0.40 mm 00.40 mm to 0.25 mm 10.25 mm to 0.15 mm Disregard unless 2 defects within a 10mm x 10 mm square.<0.15 mm Disregard7.3.2 Finished Cut – Size smaller than 7”Diameter/Equivalent DiameterMaximum Allowable (Using 3M Limit Gauge)> 0.40 mm 00.40 mm to 0.25 mm 00.25 mm to 0.15 mm Disregard unless 2 defects within a 10mm x 10 mm square.<0.15 mm Disregard7.3.3 Finished Cut Part – All sizesScratches and Similar (reflected light)Maximum Allowable Diameter/Equivalent Diameter(Using 3M Limit Gauge)Length > 2.5 mmORWidth > 0.1 mm1Length < 2.5 mm,AND0.05 mm < Width < 0.1 mmWidth < 0.05 mm Disregard7.3.4 Other defectDimples/Dents (Reflected light):Maximum AllowableDiameter/Equivalent Diameter(Using 3M Limit Gauge)> 0.8 mm 0>0.4 mm to < 0.8 mm1(for display >=7”)>0.4 mm to < 0.8 mm(for display <7”)< 0.4 mm DisregardColor Point:Point defect with colors other than black or white is also viewed as a point defect, thus is to be judged with point defect criteria.Color halo:If a color halo phenomenon contains a debris inside, adopt point defect criteria to judge. Otherwise use PAS with the defined 30-degree view angle.Surrounding air bubble:Judge based on lamination result to a substrate. If an air bubble is found then, it is counted unacceptable.Note: Excluding the edge unevenness and bumps due to cutting process.7.4 Lamination quality7.4.1 Delamination is not allowed in the usable area of the master sheet(5 mm from the edge of the sheet).7.4.2 No visible delamination along the edge of the part when laminatedto a smooth glass surface for the final cut part.7.4.3 Delamination specifications do not apply to the protective liners.7.5 Acceptance Criteria7.5.1 If a defect is visible, refer to the size requirement shown in thetable in section 7.3.7.5.2 If the defect is not visible per section 7.3, the part is acceptable.7.5.3 Air bubbles, with no debris between the release liner and adhesiveare acceptable if not observed after product lamination.7.5.4 Defects in release liner are acceptable if they do not affect filmquality after lamination of product to glass.7.5.5 Sheets shall be free of release liner wrinkles.7.5.6 If the defect can be removed by air-blowing the part with ionizedair, the part is acceptable.7.5.7 Final judgment on all defects not specifically covered here will befitness for use.7.6 New DefectIf a new defect type is found, a discussion will be held between thecustomer and 3M.8.0 MeasurementCharacteristic DescriptionThickness MicrometerSize Caliper or optical comparatorEdge Finish Visual. Cut edge quality is measured as a function of laminationquality to a smooth glass surface.Hardness Procedure: Condition sample at 23C/50% RH for > 16 hours. Placesample on a smooth glass surface. Using a proper fixture with 200 g ofweight on pencil and 45° alignment of pencil, move the pencil across thesample. Perform evaluation for visual gouging or cracking of hard coat.Adjust pencil hardness as necessary and repeat. Conforms to ASTMD3363.Surface Energy Equipment: Dyne pen, 30 dynes/cmProcedure: Apply pen solution to sample. Wait 3 seconds and observefor beading of solution. If solution beads, surface is less than 30dynes/cm.Chemical Resistance Equipment: Liquid dropper, covering dishImmediate & 5-minute Fluid(s): Bleach, MEK, IPA, Acetone, Window Cleaner, Motor Oil, Cola, Coffee, Water Insoluble Marker, & Water. Procedure: Drop fluid onto film surface via liquid dispenser, 1 cm diameter puddle. Cover with dish. Wait appropriate time interval. Confirm visual appearance and surface energy remains unchanged.Abrasion Resistance Equipment: Atlas Instruments CrockmeterAbrasive: #0000 steel woolPressure: 1600g/in2 or 250g/cm2Light scratching allowed with 20 rubs #0000 steel wool,2000 g weight and 1.25 inch diameter steel wool pad Procedure: Condition sample at 23C/50% RH for > 16 hours. Mount steel wool pad on abrader. Mount sample flat against smooth surface. Rub sample 10 times and perform visual evaluation.Taber Abrasion Equipment: Model 5150 Taber Abraser, Discs: CS-10 abrading wheels Procedure: ASTM-D 4060-1< 8% ∆ HazeSpecular Reflection Equipment: Hunter Labs, UltraScan XEMode: RSIN (R eflectance S pecular In cluded &RSEX (R eflectance S pecular Ex cluded)Measure sample in RSIN and RSEX mode.Specular Reflection = RSIN Y – RSEX YHaze,Transmission,ClarityEquipment: BYK-Gardner Haze-gard Plus Illuminant: CStatic Charge Decay Equipment: ETS Static Decay Meter, Model 406C or 406D Procedure: Measure by placing sample with hard coat facing electrodes.9.0 Environmental testing9.1 Testing Condition - Testing should be performed with the release linerremoved at the non-condensing conditions below.Test ConditionHumidity Resistance 60°C/90% RH for 500 hrsHeat Resistance 85°C for 500 hrsCold Resistance -40°C for 500 hrsThermal Shock Resistance (Hot/Cold) 85°C for 1 hr to -40°C for 1 hr, 100 cycles9.2 SpecificationProperty JudgementAppearance No significant change when observed withthe unaided eye.Transmission > 91%10.0 PatentThis product, uses thereof, or its manufacture may be covered by one or more ofthe patents listed on the package labels.11.0 PackagingMaterial will be packaged per packaging standard based on the SKU number.12.0 Warranty Period and Storage Conditions3M warrants that the products produced to this specification will meet thisspecification for twelve (12) months from the date of shipment to Purchaser fromthe 3M selling organization provided that the product is stored flat in accordancewith the requirements in section 13.0 above and in the original package under thefollowing conditions: temperature of 20 ±10°C and at a relative humidity of 45±15%. If product is shown to be defective during this warranty period, 3M’ssole liability and purchaser’s exclusive remedy is, at 3M’s option, for 3M torefund the purchase price of the product or provide replacement product in thequantity shown to be defective.3M makes no additional warranties, express or implied, including but notlimited to, any implied warranties of merchantability or fitness for aparticular purpose. In particular, but without limitation, 3M makes norepresentations or warranties concerning the effective life of the products or theirability to survive user’s environmental testing. Purchaser is responsible fordetermining whether the 3M products are fit for the purchaser’s particular purposeand suitable for the purchaser’s method of production.3M shall not be liable for any loss or damages, whether non-specified direct,indirect, special, incidental or consequential (including downtime, loss ofprofits or goodwill) regardless of the legal theory asserted.。

3M Novec Engineered Fluids 说明书

3M™Novec™Engineered Fluidsfor coating, cleaningand lubricant formulationsAll the performance. No compromise.3M Science. Applied to Life.™No trade-offs. Just results.To formulate quality products,you need solvents that seta new standard of performance.When creating new coatings, cleaners and lubricants, you’re always looking for new ways to push performance higher so your customers see better results. This is where your choice of solvent makes a big difference—the performance and quality of the fluid you choose can significantly impact the quality of your final product.At 3M, we understand it can sometimes be a challenge to find a balanced solution for your formulations. You may think you have to sacrifice safety, sustainability or both for high performance. But with 3M™ Novec™ Engineered Fluids, a proprietary family of safe and sustainable solvents, there is no compromise.Novec fluids offer an outstanding combination of performance, safety and environmental properties, allowing you to provide your customers with unique new solutions that get the job done. And with their excellent materials compatibility, you’ll have the formulating freedom you need to create the perfect mix.A versatile, sustainable solution The unique properties of Novec fluids providea balanced, cost-effective solution for your toughest formulation and performance challenges:• L ow global warming potential (GWP)• Zero ozone depletion potential• N ot scheduled for regulatory restrictionor phase-out• N eat Novec fluids are non-chlorinated and exempt from the U.S. EPA definitions for Volatile Organic Compounds (VOCs)• Non-flammable• Non-conductive• E xcellent materials compatibility• N on-corrosive• Low toxicity• H igh margin of worker safety• S ustainable alternative to hydrochlorofluorocarbons (HCFCs), hydrofluorocarbons (HFCs)and other common industrial solvents3M™ Novec™ Engineered Fluids for coating, cleaning and lubricant formulationsSolutions powered by science3M™ Novec™ Engineered Fluids are based on a proprietary 3M chemistry. The invention of this unique, low-global warming potential chemistry is part of 3M’s longstanding commitment to continually improve the environmental, health and safety profiles of our chemical products. The physical properties of these materials also make them an ideal solution for delivering value in many of today’s most demanding solvent and lubricant applications:• C oatings– Touch screens– Protection of electronic components• Precision cleaners• L ubricants– Fluorinated lubricants, including dry lubricants– Silicones– Hydrocarbon lubricantsMeeting your formulating challengesRegulatory: For regulatory information about this product, contact your 3M representative.Technical Information: The technical information, recommendations and other statements contained in this document are based upon tests or experience that 3M believes are reliable, but the accuracy or completeness of such information is not guaranteed.Product Use: Many factors beyond 3M’s control and uniquely within user’s control can affect the use and performance of a 3M product in a particular application. Given the variety of factors that can affect the use and performance of a 3M product, user is solely responsible for evaluating the 3M product and determining whether it is fit for a particular purpose and suitable for user’s method of application.Warranty, Limited Remedy, and Disclaimer: Unless an additional warranty is specifically stated on the applicable 3M product packaging or product literature, 3M warrants that each 3M product meets the applicable 3M product specification at the time 3M ships the product. 3MMAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY IMPLIED WARRANTY OR CONDITION ARISING OUT OF A COURSE OF DEALING, CUSTOM OR USAGE OR TRADE. If the 3M product does not conform to this warranty, then the sole and exclusive remedy is, at 3M’s option, replacement of the 3M product or refund of the purchase price.Limitation of Liability: Except where prohibited by law, 3M will not be liable for any loss or damage arising from the 3M product, whether direct, indirect, special, incidental or consequential, regardless of the legal theory asserted, including warranty, contract, negligence or strict liability.The 3M ™ Novec ™ Brand FamilyThe Novec brand is the hallmark for a variety of proprietary 3M products. Although each has its own unique formula and performance properties, all Novec products are designed in common to address the need for safe, effective, sustainable solutions in industry-specific applications. These include precision and electronics cleaning, heat transfer, fire protection, protective coatings, immersioncooling, advanced insulation media replacement solutions and several specialty chemical applications.Please recycle. Printed in USA. ©3M 2017. All rights reserved. Issued: 2/17 11966HB 60-5002-0983-2Electronics Materials Solutions Division 3M Center, Building 224-3N-11St. Paul, MN 55144-1000 USA Phone 1-800-810-8513Web 3M ™ Novec ™ Engineered Fluids 3M ™ Novec ™ Aerosol Cleaners 3M ™ Novec ™ 1230 Fire Protection Fluid 3M ™ Novec ™ Electronic Grade Coatings 3M ™ Novec ™ Electronic Surfactants 3M ™ Novec ™ Dielectric Fluids3M and Novec are Trademarks of 3M.Used under license by 3M subsidiaries and affiliates. Vertrel is a trademark of The Chemours Company.3M ™ Novec ™ Engineered Fluids for coating, cleaning and lubricant formulationsEngineered for long-term regulatory complianceNovec fluids are not targeted for regulatory phasedown, unlike conventional solvents such as hydrochlorofluorocarbons (such as HCFC-225) and hydrofluorocarbons (HFCs like Vertrel ™ XF specialty fluid from Chemours). Novec fluids are also a safer alternative to n-propyl bromide (nPB) and trichloroethylene (TCE) because of their wide margin of safety.Let’s get started—togetherNot sure which Novec fluid is right for your particular application? We are here to help! Please use the contact information below to learn more and get started today. Or visit /Novec for product specific information.。

3M2510MSDS胶水

Material Safety Data SheetCopyright, 2003, 3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.SECTION 1: PRODUCT AND COMPANY IDENTIFICATIONPRODUCT NAME:3M(tm) Scotch-Grip(tm) Fastener Adhesive EC-2510 (Neutral) (Dry Composition - Not AsSold)MANUFACTURER:3MDIVISION:Automotive DivisionADDRESS:3M CenterSt. Paul, MN 55144-1000EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours)Issue Date:07/11/2003Supercedes Date:Initial IssueDocument Group:18-6499-0Product Use:Specific Use:Assembly of motored machinerySECTION 2: INGREDIENTSIngredient C.A.S. No.% by WtBisphenol A-Epichlorohydrin copolymer25068-38-6 35 - 45Urea, polymer with formaldehyde and 1,3,5-triazine-2,4,6-triamine25036-13-9 30 - 40POLYVINYL ALCOHOL, REACTION PRODUCT WITH BUTYRALDEHYDE63148-65-2 1 - 104,4'-Trimethylenedipiperidine16898-52-5 1 - 10N-Butyl glycidyl ether2426-08-6 1 - 5Silica gel63231-67-4 1 - 52-ethyl-4-methyl-imidazole931-36-2 1 - 5NOTE: This Material Safety Data Sheet is intended to be descriptive of a "dried" fastener adhesive, although this is not the form in which it is sold and applied. Readers of this MSDS and applicators of the product are urged to consult Document Number 05-9044-8, which describes the "wet" form of 3M(tm) Scotch-Grip(tm) Fastener Adhesive, the form in which it is sold.SECTION 3: HAZARDS IDENTIFICATION3.1 EMERGENCY OVERVIEWOdor, Color, Grade: Residual toluene odorGeneral Physical Form: SolidImmediate health, physical, and environmental hazards: May cause chemical eye burns. May cause severe skin irritation. May cause allergic skin reaction. Contains a chemical or chemicals which can cause birth defects or other reproductive harm. May cause target organ effects.3.2 POTENTIAL HEALTH EFFECTSEye Contact:Corrosive (Eye Burns): Signs/symptoms may include cloudy appearance of the cornea, chemical burns, severe pain, tearing, ulcerations, significantly impaired vision or complete loss of vision.Skin Contact:Severe Skin Irritation: Signs/symptoms may include localized redness, swelling, itching, dryness, cracking, blistering, and pain. Allergic Skin Reaction (non-photo induced): Signs/symptoms may include redness, swelling, blistering, and itching.Inhalation:Upper Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and throat pain.May be absorbed following inhalation and cause target organ effects.Ingestion:Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, nausea, diarrhea and vomiting.May be absorbed following ingestion and cause target organ effects.Target Organ Effects:Central Nervous System (CNS) Depression: Signs/symptoms may include headache, dizziness, drowsiness, incoordination, nausea, slowed reaction time, slurred speech, giddiness, and unconsciousness.Contains a chemical or chemicals which can cause birth defects or other reproductive harm.SECTION 4: FIRST AID MEASURES4.1 FIRST AID PROCEDURESThe following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are followed.Eye Contact: Immediately flush eyes with large amounts of water for at least 15 minutes. Get immediate medical attention.Skin Contact: Remove contaminated clothing and shoes. Immediately flush skin with large amounts of water. Get medical attention. Wash contaminated clothing and clean shoes before reuse.Inhalation: Remove person to fresh air. If signs/symptoms develop, get medical attention.If Swallowed: Do not induce vomiting. Give victim two glasses of water. Never give anything by mouth to an unconscious person. Get immediate medical attention.SECTION 5: FIRE FIGHTING MEASURES5.1 FLAMMABLE PROPERTIESAutoignition temperature No Data AvailableFlash Point Not ApplicableFlammable Limits - LEL Not ApplicableFlammable Limits - UEL Not Applicable5.2 EXTINGUISHING MEDIAOrdinary combustible material. Use fire extinguishers with class A extinguishing agents (e.g., water, foam).5.3 PROTECTION OF FIRE FIGHTERSSpecial Fire Fighting Procedures: Wear full protective clothing, including helmet, self-contained, positive pressure or pressure demand breathing apparatus, bunker coat and pants, bands around arms, waist and legs, face mask, and protective covering for exposed areas of the head.Unusual Fire and Explosion Hazards: Not applicable.Note: See STABILITY AND REACTIVITY (SECTION 10) for hazardous combustion and thermal decomposition information.SECTION 6: ACCIDENTAL RELEASE MEASURESAccidental Release Measures: Refer to other sections of this MSDS for information regarding physical and health hazards, respiratory protection, ventilation, and personal protective equipment. Call 3M-HELPS line (1-800-364-3577) for more information on handling and managing the spill. Evacuate unprotected and untrained personnel from hazard area. The spill should be cleaned up by qualified personnel. Avoid contact with incompatible materials listed in the Reactivity Data Section. Collect as much of the spilled material as possible. Use appropriate and recommended personal protective equipment for the spill clean up. Use wet sweeping compound or water to avoid dusting and sweep up. Or collect spilled material using a vacuum cleaner such as the 3M Brand Model SV - 497 - AJM, with a High Efficiency Particulate Air (HEPA) filter. Warning! A motor could be an ignition source and could cause flammable gases or vapors in the spill area to burn or explode. Clean up residue with an appropriate solvent selected by a qualified and authorized person. Ventilate the area with fresh air. Read and follow safety precautions on the solvent label and MSDS. Place in an approved metal container. Dispose of collected material as soon as possible.In the event of a release of this material, the user should determine if the release qualifies as reportable according to local, state, and federal regulations.SECTION 7: HANDLING AND STORAGE7.1 HANDLINGDo not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water. For industrial or professional use only. Avoid eye contact with dust or airborne particles. Use general dilution ventilation and/or local exhaust ventilation to control airborne exposures to below Occupational Exposure Limits. If ventilation is not adequate, use respiratory protection equipment. Avoid contact with water.7.2 STORAGEStore in a cool place. Store away from acids.SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION8.1 ENGINEERING CONTROLSUse with appropriate local exhaust ventilation.8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE)8.2.1 Eye/Face ProtectionAvoid eye contact.The following eye protection(s) are recommended: Indirect Vented Goggles.8.2.2 Skin ProtectionAvoid skin contact. Select and use gloves and/or protective clothing to prevent skin contact based on the results of an exposure assessment. Consult with your glove and/or protective clothing manufacturer for selection of appropriate compatible materials.8.2.3 Respiratory ProtectionAvoid breathing of dust. Avoid breathing of vapors.Select one of the following NIOSH approved respirators based on airborne concentration of contaminants and in accordance with OSHA regulations: Half facepiece or fullface air-purifying respirator with organic vapor cartridges. Consult the current 3M Respiratory Selection Guide for additional information or call 1-800-243-4630 for 3M technical assistance.8.2.4 Prevention of SwallowingDo not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water.8.3 EXPOSURE GUIDELINESIngredient Authority Type Limit Additional InformationN-Butyl glycidyl ether ACGIH TWA25 ppmN-Butyl glycidyl ether OSHA TWA,25 ppmVacatedN-Butyl glycidyl ether OSHA TWA50 ppm Table Z-1Silica gel CMRG TWA 2 mg/m3VAC Vacated PEL:Vacated Permissible Exposure Limits [PEL] are enforced as the OSHA PEL in some states. Check with your local regulatory agency.SOURCE OF EXPOSURE LIMIT DATA:ACGIH: American Conference of Governmental Industrial HygienistsCMRG: Chemical Manufacturer Recommended GuidelineOSHA: Occupational Safety and Health AdministrationAIHA: American Industrial Hygiene Association Workplace Environmental Exposure Level (WEEL)SECTION 9: PHYSICAL AND CHEMICAL PROPERTIESOdor, Color, Grade:Residual toluene odorGeneral Physical Form:SolidAutoignition temperature No Data AvailableFlash Point Not ApplicableFlammable Limits - LEL Not ApplicableFlammable Limits - UEL Not ApplicableBoiling point Not ApplicableVapor Density No Data AvailableVapor Pressure No Data AvailableSpecific Gravity Approximately 1 [Ref Std: WATER=1]pH Not ApplicableMelting point No Data AvailableSolubility in Water No Data AvailableEvaporation rate No Data AvailableVolatile Organic Compounds Not ApplicablePercent volatile No Data AvailableVOC Less H2O & Exempt Solvents Not ApplicableViscosity Not ApplicableSECTION 10: STABILITY AND REACTIVITYStability: Stable.Materials and Conditions to Avoid: Amines; Alcohols; WaterAdditional Information: SolventsHazardous Polymerization: Hazardous polymerization will not occur.Hazardous Decomposition or By-ProductsSubstance ConditionAldehydes During CombustionCarbon monoxide During CombustionCarbon dioxide During CombustionSECTION 11: TOXICOLOGICAL INFORMATIONPlease contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its components.SECTION 12: ECOLOGICAL INFORMATIONECOTOXICOLOGICAL INFORMATIONNot determined.CHEMICAL FATE INFORMATIONNot determined.SECTION 13: DISPOSAL CONSIDERATIONSWaste Disposal Method: Dispose of completely cured (or polymerized) wastes in a sanitary landfill.As a disposal alternative, incinerate in an industrial or commercial facility in the presence of a combustible material.EPA Hazardous Waste Number (RCRA): Not regulatedSince regulations vary, consult applicable regulations or authorities before disposal.SECTION 14:TRANSPORT INFORMATIONPlease contact the emergency numbers listed on the first page of the MSDS for Transportation Information for this material.SECTION 15: REGULATORY INFORMATIONUS FEDERAL REGULATIONSContact 3M for more information.311/312 Hazard Categories:Fire Hazard - No Pressure Hazard - No Reactivity Hazard - No Immediate Hazard - Yes Delayed Hazard - YesSTATE REGULATIONSContact 3M for more information.CHEMICAL INVENTORIESContact 3M for more information.INTERNATIONAL REGULATIONSContact 3M for more information.This MSDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200. SECTION 16: OTHER INFORMATIONNFPA Hazard ClassificationHealth: 2 Flammability: 1 Reactivity: 0 Special Hazards: NoneNational Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to be generated in significant quantities.No revision information is available.DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a particular purpose and suitable for user's method of use or application.3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy. In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M.3M MSDSs are available at 。

标志标线技术参数

资料范本本资料为word版本，可以直接编辑和打印，感谢您的下载标志标线技术参数地点：__________________时间：__________________说明：本资料适用于约定双方经过谈判，协商而共同承认，共同遵守的责任与义务，仅供参考，文档可直接下载或修改，不需要的部分可直接删除，使用时请详细阅读内容（三）技术要求及主要性能指标总体技术要求供应商提供的货物及服务须满足技术先进、质量优良、供货及时、服务周到的总体要求，并保证正常、安全、可靠的使用。

供应商投标的设备必须是全新制造的，不得利用旧料进行加工而成。

主要技术指标及要求标线符合设计要求，达到交通行业标准JT/T280-2004《路面标线涂料》要求，并满足以下要求：涂料密度：1.8～2.3g/cm3；涂膜外观：涂膜冷凝后应无皱纹、斑点、起泡、裂纹、脱落及表面无发粘现象，涂膜的颜色和外观与标准板差别不大；色度性能：按JT/T280-1995标准6.2.6规定的方法测试；抗压强度：≥12 Mpa；耐磨性（200r/1000g后减重）：≤50 mg；逆反射系数mcd.1×-1.m-2，白色≥200，黄色≥100；耐候性：经12个月试验，涂膜的起皱、斑点、裂纹、脱落及变色等都不大于标准样板；涂料用下涂剂颜色应无透明或琥珀色流；固体含量：30%±5；涂布量：120～200g/ m2；干燥时间：≤5 min；玻璃珠的技术条件：密度（在23℃±2℃的二甲苯中）2.4～2.6g/ m3；外观无色透明球状，扩大10～50倍观察时，熔融团、片状、尖状物、有气泡等瑕庇不应超过总量的20%，玻璃珠的折射率（20℃浸渍法≥1.5）；玻璃珠含量：涂料中含20%～30%的玻璃珠，施工时撒布玻璃珠于热熔涂料上。

制作道路标线使用热熔反光涂料；制作标线的热熔涂料、底漆、玻璃珠要经交通部检测机构检测合格才能使用；人行横道线、人行预告标志、箭头、导流线制作符合GB5768-2009规定；标线厚度不少于1.8mm，亮度因数≥0.27，双实线为黄色，车道线为白色，其他标线、箭头等符合GB5768-2009规定。

3M Scotchcast Inline Splicing Kits 72-N系列说明书

Product Description3M™ Scotchcast™ Inline Splicing Kits 72-N Series is a series of rigid body splices tailored for joining signal and control cables. The kits are designed to accommodate shielded or unshielded constructions of plastic or rubber-jacketed cables. Six kit sizes cover a range of cables up to 100-pair (200 conductors) 10 AWG or 200-pair (400 conductors) 22 AWG. The 72-N series splice consists of a rigid-body mold filled with pliable polyurethane 3M Scotchcast Electrical Insulating and Sealing Compound 2104.Jumper wires with clips provide for shield continuity on shielded cables. Built-in spacer webbing automatically provides for cable centering and proper compound coverage. The kits are sized for, but do not include, 3M™ Scotchlok™Insulated Butt Connectors. The completed splice is designed and tested for direct burial.Kit ContentsEach kit contains sufficient quantities of the following materials to make one (1) splice, excluding inline connectors:• O ne two-part translucent mold body with tongue and groove seams and built-in spacer webbing• 3M™ Scotchcast™ Electrical Insulating and Sealing Compound 2104 in convenient 3M closed mixing pouch • T wo pour spouts for kits 72-N1, 72-N2, and 72-N3; one top cap cover for kits 72-N4, 72-N5 and 72-N6• S cotch® Rubber Splicing Tape 23 for constructing sealing collars and sealing splice body ends• O ne nonconductive abrasive cloth for preparing cable• O ne bonding (jumper) wire with clips for providing solderless shield continuity on shielded cables (except72-N1 kit)• I nstructions showing proper installation techniques for shielded and unshielded signal and control cablesSplice Features• V ersatility is designed into each kit to allow a wide range of cable sizes • T he 72-N2 through 72-N6 kits will accommodate shielded or unshielded cable. The 72-N1 kit is recommended for unshielded cable only• C onvenient kits simplify ordering and stocking• K its provide all materials needed to reinsulate, reconnect shield, and rejacket one splice• C ompound has low viscosity for fast, complete filling of splice• C ompound has low exotherm which will not damage plastic insulated cable• C onvenient closed mixing pouch container permits clean, easy compound handling• P olypropylene mold with built-in spacer web automatically provides for cable centering and compound coverage• No special tools required; normal hand tools only ApplicationsTo splice signal and control cables rated up to 1000 volts, sized 0.25–3.25" (6.4–82.6 mm) O.D.• F or inline splicing of shielded or unshielded cables• For use on plastic or rubber jacketed cables• For use on cables with plastic or rubber insulated conductors • For use in direct burial applications• F or use with underground systems— Manhole— Handhole— Junction box• F or use in indoor applications— Vault— Cable tray— Junction box— Duct• For joining of cable reel-ends• For repair of cable failures and dig-insScotchcast™Signal and Control Inline Splicing Kits 72-N SeriesData SheetPage 1 of 4Page 2 of 478-8126-5772-0-BData: Physical and Electrical Properties3M ™ Scotchcast ™ Inline Splicing Kits 72-N Series can be used on cable that operates continuously at 90°C (194°F) and has an emergency overload temperature rating of 130°C (266°F). The splices are rated at 1000 volts.Moisture-Resistance TestThermal cycling submerged in water pressurized to simulate a 1.8 m (6') head: the splice 72-N series exceeds 1.0-x-106 ohms insulation resistance after ten temperature cycles of 2°C to 24°C (35°F to 75°F).Splice Selection Guide** Figures based on IMSA cable specifications.Typical Properties3M™ Scotchcast™ Electrical Insulating and Sealing Compound 2104Property Test Method Typical ValueTensile Strength ASTM-D-412 600 psi (4.14 MPa) Elongation ASTM-D-412 150%Hardness Shore A 70Apparent Free Isocyanate Distill 15 min. at 170°C (338°F) and 3mm mercury vacuum 3.5%Distill 15 min. at 77°C (171°F) and 3mm mercury vacuum <0.1%Viscosity Brookfield at 20 rpm 1200 cpsGel Time 180 gm sample at 23°C (73°F) 15 min.Exotherm 180 gm sample at 24°C (75°F) 66°C (150°F) max.Water Absorption 7 days in 23°C (73°F) water 0.28%Insulation Resistance Aged 28 days/35°C (95°F) 96% RH 5 x 1010 ohmsDielectric Constant ASTM-D-150 4.1 at 103 Hz3.8 at 106 HzDissipation Factor ASTM-D-150 0.04 at 103 Hz0.05 at 106 HzHydrolytic Stability 7 days in water at 100°C (212°F) +2.4%-10 points Shore A hardness Dry Heat Aging 21 days at 132°C (270°F) -4.7% wt. loss + 10 Shore A Copper Corrosion 30 days at 35°C (95°F), 96% RH under 45 V 0Stress Cracking On cut and stressed polyethylene for 48 hours/49°C (120°F) 0Fungus Resistance ASTM-G-21 0SpecificationProduct(open specification)Signal and control cable splices must be capable of normal continuous operation at 1000 volts. The splices must consist of a rigid polypropylene mold body witha built-in spacer web to automatically provide for cable centering and proper compound coverage; the mold body shall be filled with a flexible polyurethane electrical compound capable of continuous operation at 90°C (194°F), with an emergency overload temperature rating of 130°C (266°F).Splices must have provisions for inline splicing of shielded or unshielded, plastic or rubber jacketed, plastic or rubber insulated, signal and control cables. The splices shall be rated for direct burial applications.Engineering/Architectural(closed specification)Splicing of all signal and control cables rated at 1000 volts or less and sized with an outside diameter of0.25"–3.25" (6.4–82.6 mm) shall be performed in accordance with the instructions provided with 3M Scotchcast Signal and Control Cable Inline Splicing Kit 72-N Series.Installation TechniquesThe exact instructions for constructing each splice are packed in each kit. The following summarizes these instructions:1. P repare cable to dimension “A” for splice opening, removing shielding and core wrapper according to steps for shielded cable or unshielded cable, as applicable. 2. I nstall 3M™ Scotchlok™ Insulated Butt Connectors, not provided, staggering individually or in pairs. Observe color coding.3. I nstall jumper bonding wire to shielded cables; construct sealing collars with Scotch® Rubber Tape 23 provided.4. T rim mold body ends to fit cable and install over splice.5. S eal mold ends with Scotch Tape 23 provided.6. Install pour spouts into kits 72-N1, 72-N2 and 72-N3.7. M ix 3M Scotchcast 2104 compound and pour into splice body, filling completely. Allow compound to cure.MaintenanceThe components within this kit are stable under normal storage conditions. Normal storage and stock rotation are recommended.The 2104 compound is not impaired by freezing; however, it should be warmed to 0°C (32°F) before being mixed and poured.Availability3M Scotchcast Inline Splicing Kits 72-N Series are available in six sizes from your local 3M authorized electrical distributor. The kits will splice signal and control cables sized 0.25"–3.25" (6.4–82.6 mm) outside diameter, as shown in the splice selection guide table.78-8126-5772-0-BPage 3 of 43M, Scotchcast and Scotchlok are trademarks of 3M Company.Scotch is a registered trademark of 3M Company.Important NoticeAll statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. Y ou assume all risks and liability associated with such use. Any statements related to the product which are not contained in3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M.Warranty; Limited Remedy; Limited Liability.This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FORA PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted.Electrical Markets Division6801 River Place Blvd.Austin, TX 78726-9000800-626-8381Fax 800-828-9329 /electrical Recycled paper40% Pre-consumer waste paper10% Post-consumer waste paperLitho in USA© 3M 2006 78-8126-5772-0-BPage 4 of 4。

3M Scotchcal高性能贯穿带颜色和模式指南Duo-Tone 746说明书

Fits '91-'92 Ford Aerostar two-tone vehicles
10
1/8"
10
3/32"
05
1/8"
10
3/16"
05
5/32"
10
31
31 05 31 05
31
60
60 21 60 21
60
1/16" 1/8" 3/16"
Single Stripe
701
Warranty and Limited Remedy: 3M warrants that each 3M product meets the applicable 3M product specification at the time 3M ships the product. 3M MAKES NO OTHER EXPRESS OR IMPLIED WARRANTIES OR CONDITIONS, INCLUDING ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If the 3M product does not conform to this warranty, the sole and exclusive remedy is, at 3M’s option, replacement of the 3M product or refund of the purchase price.
Limitation of Liability: Except where prohibited by law, 3M will not be liable for any loss or damage arising from the 3M product, whether direct, indirect, special, incidental or consequential, regardless of the legal theory asserted.

3M Cold Shrink End Caps EC-Series 数据手册说明书

3M ™Cold Shrink End Caps EC-SeriesDescription3M Cold Shrink End Caps are close-ended, tubular rubber sleeves that are factory expanded and loaded onto a removable core. When positioned over the end of a cable, or other cylindrical object, the core is removed to provide a reliableenvironmental seal. Four different end caps are available to accommodate a wide range of sizes .EHS∙3M Cold Shrink Removable Core is a mixed polymer and recyclable with waste.∙ Read all Health Hazard, Precautionary and First Aid statements found in the MaterialSafety Data Sheet (MSDS) and/or product label prior to handling or use .ApplicationsMoisture sealing and physical protection for cables, pipes or other cylindrical objects.Agency Approvals & Self CertificationsWorking around energized systems may cause serious injury or death. Installation should be performed by personnel familiar with good safety practice in handling electrical equipment. De-energize and ground all electrical systemsFeatures • Simple and fast installation, no tools required • Accommodates size ranges from 0.46” -3.32” • Good abrasion resistance• Seals tight, retains resiliency for years• Water resistant• No mastic or tape required• Resists acids and alkalis• Resists ozone• Easy removalTypical Physical Properties Not for specifications. Values are typical, not to be considered minimum or maximum. Properties measured at room temperature 73°F (~23°C) unless otherwise stated.EPDM RubberPhysical Property (Test Method)Typical ValueUS units (metric)Color Black300% Modulus (ASTM D 412-87)480 psi (3,3 MPa)Ultimate Tensile (ASTM D 412-87)1400 psi (9,6 MPa)Ultimate Elongation (ASTM D 412-87)750%Die C Tear (ASTM G-21)150 pli (26,3 KN/m)Moisture Absorption - 7 days in H2O Wt. Gain 1.8%Selection ChartUse RangeProduct# inches (mm)EC-10.46 - 0.82(11,6 - 20,9)EC-20.63-1.18(15,9 - 30,1)EC-3 1.02-1.94(26,0 - 49,2)EC-4 1.79 - 3.32(45,5 - 84,3) Maintenance3M Cold Shrink End Caps EC-Series are stable under normal storage conditions. The end caps are not impaired by freezing or overheating due to ambient temperaturesencountered during shipping or storage. Normal storage and stock rotation arerecommended.Shelf Life & Storage This product has a 5-year shelf life from date of manufacture when stored in a humidity controlled storage (10°C/50°F to 27°C/80°F and <75% relative humidity).Availability Please contact your local distributor; available from /electrical [Where to Buy] or call 1.800.245.3573.3M, Super 33+ and Scotch are trademarks of 3M Company.3Electrical Markets Division6801 River Place Blvd.Austin, TX 78726-9000 800.245.3573FAX: 800.245.0329 /electrical Please recycle© 3M 2013 All rights reserved 78-8125-9558-1 Rev BImportant Notice All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Beforeusing this product, you must evaluate it and determine if it is suitable for your intended application.You assume all risks and liability associated with such use. Any statements related to the product,which are not contained in 3M’s current publications, or any contrary statements contained on yourpurchase order, shall have no force or effect unless expressly agreed upon, in writing, by anauthorized officer of 3M.Warranty; Limited Remedy; Limited Liability This product will be free from defects in material and manufacture at the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted.。

1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。

3M道路标线产品SPEC IN 写法
1. 对于AWT（全天候热熔反光标线（水下反光））的Spec in的技术要求可按如下写法：
道路标线材料使用热熔标线涂料，涂料颜色的色品坐标和亮度因数应符合JT/T280-2004中的规定；为了雨天夜间更好地起到引导作用，采用的热熔标线应具有水下反光功能的3M微晶陶瓷珠，并符合《道路交通标线质量要求和检测方法》GB/T16311-2005的规定，干燥条件的最初逆反射系数(mcd.lx-1m-2)不低于350（白色）/275（黄色）；潮湿条件的最初逆反射系数(mcd.lx-1m-2)不低于350（白色）/275（黄色）。

技术参数：
备注：生产商须能够提供对该产品在使用现场的逆反射系数检测报告。

2. 对于AWP（双组份涂料）的Spec in的技术要求可按如下写法：
道路标线材料使用双组份标线涂料，涂料颜色的色品坐标和亮度因数应符合JT/T280-2004中的规定；为了雨天夜间更好地起到引导作用，采用的双组分标线应具有水下反光功能，并符合《道路交通标线质量要求和检测方法》GB/T16311-2005的规定，干燥条件的最初逆反射系数(mcd.lx-1m-2)不低于350（白色）/275（黄色）；潮湿条件的最初逆反射系数(mcd.lx-1m-2)不低于300（白色）/225（黄色）。

技术参数：
备注：生产商须能够提供对该产品在使用现场的逆反射系数检测报告。

3. 产品名称：3M钻石级雨夜反光成型标线带（380WR）
符合标准：1.该产品为道路预成型标线带，产品结构属于交通行业标准
JT/T493-2003《道路预成型标线带》中“长效二型“的类别。

2.该产品逆反射系数应符合交通行业标准JT/T493-2003《道路预成型标线带》中
“Ⅰ级”的要求。

结构特点：1. 产品自带背胶，可以直接粘贴在路面上（需预涂底涂剂）。

2. 产品表面有规则分布的四边形突起，突起四边形的边长约
为7-8mm，突起高度为1.6mm，突起表面镶嵌耐磨微晶陶
瓷珠，具有良好的反光、排水，防滑功能。

性能特点：该标线带要具有全天候的反光效果，保证无论是晴天夜晚还
是雨天夜晚都具有优秀的反光性能，其在干燥和下雨状态下
的初始最低逆反射系数必须满足下表要求：
2
2
备注：生产商须能够提供对该产品在使用现场的逆反射系数检测报告。

4. 产品名称：3M钻石级反光成型标线带（380IES）
符合标准：1.该产品为道路预成型标线带，产品结构属于交通行业标准
JT/T493-2003《道路预成型标线带》中“长效二型“的类别。

2.该产品逆反射系数应符合交通行业标准JT/T493-2003《道路预成型标线带》中
“Ⅰ级”的要求。

结构特点：1. 产品自带背胶，可以直接粘贴在路面上（需预涂底涂剂）。

2. 产品表面有规则分布的菱形突起，突起菱形的边长约
为6-7mm，突起高度为1.6mm，突起表面镶嵌耐磨微晶陶
瓷珠，具有良好的反光、排水，防滑功能。

性能特点：该标线带要具有全天候的反光效果，保证无论是晴天夜晚还是雨天夜晚都具有优秀的反光性能，其在干燥和下雨状态下
的初始最低逆反射系数必须满足下表要求：
2
备注：生产商须能够提供对该产品在使用现场的逆反射系数检测报告。

3M道路标线产品SPEC IN 写法

危险品说明书-涂料

3M使用手册

3M Scotchcast Connector Sealing Pack 3570G-N 数据表说明

3M EMMD胶水及指示标签

3M 中高压电缆接线、终端和接口设备说明书

3M Rigid Parts Repair Technical Data说明书

3M610材质报告

3M SJ3572 Hook Fastener产品说明说明书

3M GasAlertMicroClip XL – 规格 说明书

3M Scotch 盒缝胶带吊带 HR-80 HR-83 说明书

3M汽身运用

3M 胶带产品说明书

3M 检验标准

3M Novec Engineered Fluids 说明书

3M2510MSDS胶水

标志标线技术参数

3M Scotchcast Inline Splicing Kits 72-N系列说明书

3M Scotchcal高性能贯穿带颜色和模式指南Duo-Tone 746说明书

3M Cold Shrink End Caps EC-Series 数据手册说明书

3M GasAlertMicroClip XL – 规格说明书