酸碱浓度变送器AX43说明书

Health and Safety To ensure that our products are safe and without risk to health, the following points must be noted: 1. The relevant sections of these instructions must be read carefully before proceeding. 2. Warning labels on containers and packages must be observed. 3. Installation, operation, maintenance and servicing must only be carried out by suitably trained personnel and in accordance with the information given. 4. Normal safety precautions must be taken to avoid the possibility of an accident occurring when operating in conditions of high pressure and/ or temperature. 5. Chemicals must be stored away from heat, protected from temperature extremes and powders kept dry. Normal safe handling procedures must be used. 6. When disposing of chemicals ensure that no two chemicals are mixed. Safety advice concerning the use of the equipment described in this manual or any relevant hazard data sheets (where applicable) may be obtained from the Company address on the back cover, together with servicing and spares information.
User Guide
IM/AX4CO4_2
AnalyzeIT Single and Dual Input Analyzers for High Level Conductivity
Models AX413, AX430, AX433, AX436 & AX438
ABB
The Company
We are an established world force in the design and manufacture of instrumentation for industrial process control, flow measurement, gas and liquid analysis and environmental applications. As a part of ABB, a world leader in process automation technology, we offer customers application expertise, service and support worldwide. We are committed to teamwork, high quality manufacturing, advanced technology and unrivalled service and support. The quality, accuracy and performance of the Company’s products result from over 100 years experience, combined with a continuous program of innovative design and development to incorporate the latest technology. The NAMAS Calibration Laboratory No. 0255 is just one of the ten flow calibration plants operated by the Company, and is indicative of our dedication to quality and accuracy.
Symbols
One or more of the following symbols may appear on the instrument labelling:
Warning – Refer to the manual for instructions Caution – Risk of electric shock Protective earth (ground) terminal Earth (ground) terminal
Information in this manual is intended only to assist our customers in the efficient operation of our equipment. Use of this manual for any other purpose is specifically prohibited and its contents are not to be reproduced in full or part without prior approval of the Technical Publications Department.
Direct current supply only Alternating current supply only Both direct and alternating current supply The equipment is protected through double insulation
Cert. No. Q05907 EN ISO 9001:1994
EN 29001 (ISO 9001)
Lenno, Italy – Cert. No. 9/90AStonehou来自e, U.K.0255
Electrical Safety
This instrument complies with the requirements of CEI/IEC 61010-1:2001-2 'Safety Requirements for Electrical Equipment for Measurement, Control and Laboratory Use'. If the instrument is used in a manner NOT specified by the Company, the protection provided by the instrument may be impaired.
CONTENTS
Section 1 Page Section 6 Page
INTRODUCTION .............................................................. 2 1.1 System Description ................................................. 2 1.2 PID Control – AX430 Analyzer Only ......................... 2 1.3 AX400 Series Analyzer Options ............................... 2 OPERATION ..................................................................... 3 2.1 Powering Up the Analyzer ....................................... 3 2.2 Displays and Controls .............................................. 3 2.2.1 Membrane Key Functions ............................ 3 2.3 Operating Page ....................................................... 6 2.3.1 Single Input 4-Electrode Conductivity ........... 6 2.3.2 Dual Input 4-Electrode Conductivity ............. 7 OPERATOR VIEWS ......................................................... 8 3.1 View Set Points ....................................................... 8 3.2 View Outputs .......................................................... 9 3.3 View Hardware ........................................................ 9 3.4 View Software ....................................................... 10 3.5 View Logbook ....................................................... 10 3.6 View Clock ............................................................ 12 SETUP ............................................................................ 13 4.1 Sensor Calibration ................................................. 13 PROGRAMMING ........................................................... 15 5.1 Security Code ....................................................... 15 5.2 Configure Display .................................................. 16 5.3 Configure Sensors ................................................. 17 5.4 Configure Alarms ................................................... 24 5.4.1 Configure Standard Alarms ........................ 24 5.4.2 Configure CIP Interface Alarm .................... 26 5.4.3 Configure CIP Status Alarm ....................... 28 5.4.3 Configure CIP Status Alarm ....................... 29 5.5 Configure Outputs ................................................. 31 5.6 Configure Clock .................................................... 33 5.7 Configure Control .................................................. 34 5.7.1 Configure Single PID Controller .................. 35 5.7.2 Configure Power Failure Recovery Mode .... 38 5.8 Configure Security ................................................. 39 5.9 Configure Logbook ............................................... 39 5.10 Test Outputs and Maintenance .............................. 40