ROS 优化CF的PING值脚本

合集下载

ROS3.30全套多线负载平衡设置脚本

ROS3.30全套多线负载平衡设置脚本ROS3.30设置脚本如果你是菜鸟，下面的脚本也许会帮了，如果你是高高手，请你多指证，谢谢下面是我花了一整天的时间整理出来的，第一次用ROS3.30，走了很多弯路，还好以前有点2.9的基础，结合在网上找些前辈门的脚本，终于测试一切正常，我自己在我的线路上测试通过，如果到你机器上有问题，请嘴上留情，别骂我，请仔细检查，相信你也一定能行的。

如果有问题实在搞不懂，可以加我QQ307237303（请先自己多钻研一下在加我）# dec/03/2011 20:55:29 by RouterOS 3.30# software id = K6BP-MUXD#/interface ethernetset 0 arp=enabled auto-negotiation=yes cable-settings=default comment="" \disable-running-check=yes disabled=no full-duplex=yes mac-address=\00:03:47:95:C8:66 mtu=1500 name=W AN3 speed=100Mbpsset 1 arp=enabled auto-negotiation=yes cable-settings=default comment="" \disable-running-check=yes disabled=no full-duplex=yes mac-address=\00:03:47:95:C2:FC mtu=1500 name=LAN speed=100Mbpsset 2 arp=enabled auto-negotiation=yes cable-settings=default comment="" \disable-running-check=yes disabled=no full-duplex=yes mac-address=\00:20:ED:1C:B3:90 mtu=1500 name=W AN1 speed=100Mbpsset 3 arp=enabled auto-negotiation=yes cable-settings=default comment="" \disable-running-check=yes disabled=no full-duplex=yes mac-address=\00:20:ED:1C:B3:91 mtu=1500 name=W AN2 speed=100Mbps以上是网卡名称设置/ip pooladd name=PPPOE-IP ranges=10.0.0.5-10.0.0.200以上是PPPOE拔号地址池/portset 0 baud-rate=9600 data-bits=8 flow-control=hardware name=serial0 parity=\none stop-bits=1set 1 baud-rate=9600 data-bits=8 flow-control=hardware name=serial1 parity=\none stop-bits=1以上是导出后不知用处的/ppp profileset default change-tcp-mss=yes comment="" name=default only-one=default \use-compression=default use-encryption=default use-vj-compression=defaultadd change-tcp-mss=default comment="" dns-server=210.21.196.6 local-address=\10.0.0.1 name=PPPOE-1 only-one=yes rate-limit=\"108k/1400k 128k/1600k 90k/1m" remote-address=PPPOE-IP use-compression=\default use-encryption=default use-vj-compression=default wins-server=\221.5.88.88add change-tcp-mss=default comment="" dns-server=210.21.196.6 local-address=\10.0.0.1 name=LOW only-one=yes rate-limit="88k/900k 108k/1100k 90k/1m" \remote-address=PPPOE-IP use-compression=default use-encryption=default \use-vj-compression=default wins-server=221.5.88.88set default-encryption change-tcp-mss=yes comment="" name=default-encryption \ only-one=default use-compression=default use-encryption=yes \use-vj-compression=default以上是PPPOE服务建立/interface pppoe-clientadd ac-name="" add-default-route=no allow=pap,chap,mschap1,mschap2 comment="" \ dial-on-demand=no disabled=no interface=WAN1 max-mru=1480 max-mtu=1480 \ mrru=disabled name=pppoe-out1 password=123 profile=default \service-name="" use-peer-dns=no user=123add ac-name="" add-default-route=no allow=pap,chap,mschap1,mschap2 comment="" \ dial-on-demand=no disabled=no interface=WAN2 max-mru=1480 max-mtu=1480 \ mrru=disabled name=pppoe-out2 password=123456 profile=default \service-name="" use-peer-dns=no user=123add ac-name="" add-default-route=no allow=pap,chap,mschap1,mschap2 comment="" \ dial-on-demand=no disabled=no interface=WAN3 max-mru=1480 max-mtu=1480 \ mrru=disabled name=pppoe-out3 password=3 profile=default service-name="" \ use-peer-dns=no user=3 以上是ADSL拔号上网的建立/queue treeadd burst-limit=0 burst-threshold=0 burst-time=0s disabled=no limit-at=0 \ max-limit=12M name=totaldown parent=global-in priority=8/queue typeset default kind=pfifo name=default pfifo-limit=50set ethernet-default kind=pfifo name=ethernet-default pfifo-limit=50set wireless-default kind=sfq name=wireless-default sfq-allot=1514 \sfq-perturb=5set synchronous-default kind=red name=synchronous-default red-avg-packet=1000 \ red-burst=20 red-limit=60 red-max-threshold=50 red-min-threshold=10set hotspot-default kind=sfq name=hotspot-default sfq-allot=1514 sfq-perturb=\ 5add kind=pcq name=PCQ-up pcq-classifier=src-address pcq-limit=50 pcq-rate=\ 1000000 pcq-total-limit=10000 add kind=pcq name=PCQ-down pcq-classifier=dst-address pcq-limit=50 pcq-rate=\ 1000000 pcq-total-limit=10000 add kind=pcq name=80-Down pcq-classifier=dst-address pcq-limit=50 pcq-rate=\ 800000 pcq-total-limit=10000 add kind=pcq name=other_down pcq-classifier=dst-address pcq-limit=50 \ pcq-rate=0 pcq-total-limit=2000 add kind=pcq name=server_down pcq-classifier=dst-address pcq-limit=50 \ pcq-rate=0 pcq-total-limit=2000add kind=pcq name=game-down pcq-classifier=dst-address pcq-limit=50 pcq-rate=\ 400000 pcq-total-limit=10000 set default-small kind=pfifo name=default-small pfifo-limit=10/queue treeadd burst-limit=0 burst-threshold=0 burst-time=0s disabled=no limit-at=1M \ max-limit=10M name=otherdown packet-mark=Port_Packet parent=totaldown \ priority=8 queue=defaultadd burst-limit=0 burst-threshold=0 burst-time=0s disabled=no limit-at=1M \ max-limit=12M name=portdown packet-mark=Port_Packet parent=totaldown \priority=1 queue=defaultadd burst-limit=0 burst-threshold=0 burst-time=3s disabled=no limit-at=5M \ max-limit=12M name=80down packet-mark=80_packet parent=totaldown \priority=2 queue=defaultadd burst-limit=0 burst-threshold=0 burst-time=3s disabled=yes limit-at=0 \ max-limit=18M name=totalup packet-mark=PCQ-up parent=global-out priority=\7 queue=default以上是网络优先设置，感觉用处不大，我是3*4M AD/snmpset contact="" enabled=no engine-boots=0 engine-id="" location="" \time-window=15 trap-sink=0.0.0.0 trap-version=1/snmp communityset public address=0.0.0.0/0 authentication-password="" \ authentication-protocol=MD5 encryption-password="" encryption-protocol=\DES name=public read-access=yes security=none write-access=no/system logging actionset memory memory-lines=100 memory-stop-on-full=no name=memory target=memory set disk disk-file-count=2 disk-file-name=log disk-lines-per-file=100 \disk-stop-on-full=no name=disk target=diskset echo name=echo remember=yes target=echoset remote bsd-syslog=no name=remote remote=0.0.0.0:514 src-address=0.0.0.0 \ syslog-facility=daemon syslog-severity=auto target=remote /user groupadd comment="" name=read policy="local,telnet,ssh,reboot,read,test,winbox,pass\word,web,sniff,sensitive,!ftp,!write,!policy"add comment="" name=write policy="local,telnet,ssh,reboot,read,write,test,winb\ox,password,web,sniff,sensitive,!ftp,!policy"add comment="" name=full policy="local,telnet,ssh,ftp,reboot,read,write,policy\ ,test,winbox ,password,web,sniff,sensitive"/interface bridge settingsset use-ip-firewall=no use-ip-firewall-for-pppoe=no use-ip-firewall-for-vlan=\ no/interface ethernet mirrorset/interface l2tp-server serverset authentication=pap,chap,mschap1,mschap2 default-profile=\default-encryption enabled=no max-mru=1460 max-mtu=1460 mrru=disabled/interface ovpn-server serverset auth=sha1,md5 certificate=none cipher=blowfish128,aes128 default-profile=\ default enabled=no keepalive-timeout=60 mac-address=FE:46:57:28:66:CB \max-mtu=1500 mode=ip netmask=24 port=1194 require-client-certificate=no/interface pppoe-server serveradd authentication=pap,chap,mschap1,mschap2 default-profile=PPPOE-1 disabled=\ yes interface=LAN keepalive-timeout=10 max-mru=1480 max-mtu=1480 \max-sessions=0 mrru=disabled one-session-per-host=no service-name=\service1/interface pptp-server serverset authentication=mschap1,mschap2 default-profile=default-encryption \ enabled=no keepalive-timeout=30 max-mru=1460 max-mtu=1460 mrru=disabled /ip accounting set account-local-traffic=no enabled=no threshold=256/ip accounting web-accessset accessible-via-web=no address=0.0.0.0/0以上也是不知的东东/ip addressadd address=192.168.2.1/24 broadcast=192.168.2.255 comment="" disabled=no \ interface=LAN network=192.168.2.0 以上是设置ROS的内网IP/ip dhcp-server configset store-leases-disk=5m/ip dnsset allow-remote-requests=yes cache-max-ttl=1w cache-size=2048KiB \ max-udp-packet-size=512 primary-dns=210.21.196.6 secondary-dns=\221.5.88.88以上是设置DNS,你的可能不一样/ip firewall connection trackingset enabled=yes generic-timeout=10m icmp-timeout=10s tcp-close-timeout=10s \ tcp-close-wait-timeout=10s tcp-established-timeout=1d \tcp-fin-wait-timeout=10s tcp-last-ack-timeout=10s \tcp-syn-received-timeout=5s tcp-syn-sent-timeout=5s tcp-syncookie=no \tcp-time-wait-timeout=10s udp-stream-timeout=3m udp-timeout=10s以上是系统默认值/ip firewall mangleadd action=change-mss chain=postrouting comment="" disabled=yes new-mss=1460 \ protocol=tcp tcp-flags=syn add action=mark-routing chain=prerouting comment="" disabled=yes \ new-routing-mark=add passthrough=no src-address-list=src1add action=mark-connection chain=prerouting comment=1 disabled=yes \ in-interface=LAN new-connection-mark=1 passthrough=yes \per-connection-classifier=src-address-and-port:3/0add action=mark-routing chain=prerouting comment="" connection-mark=1 \ disabled=yes in-interface=LAN new-routing-mark=1 passthrough=noadd action=mark-connection chain=prerouting comment=2 disabled=yes \ in-interface=LAN new-connection-mark=2passthrough=yes \per-connection-classifier=src-address-and-port:3/1add action=mark-routing chain=prerouting comment="" connection-mark=2 \ disabled=yes in-interface=LAN new-routing-mark=2 passthrough=noadd action=mark-connection chain=prerouting comment=3 disabled=yes \ in-interface=LAN new-connection-mark=3 passthrough=yes \per-connection-classifier=src-address-and-port:3/2add action=mark-routing chain=prerouting comment="" connection-mark=3 \ disabled=yes in-interface=LAN new-routing-mark=3 passthrough=noadd action=change-mss chain=forward comment="" disabled=no new-mss=1400 \ protocol=tcp tcp-flags=syn add action=add-src-to-address-list address-list=src1 address-list-timeout=5s \ chain=prerouting comment="" disabled=no dst-port=80 protocol=tcp \src-address-list=!src2add action=add-src-to-address-list address-list=src2 address-list-timeout=3h \ chain=prerouting comment="" disabled=no dst-port=80 protocol=tcp \src-address-list=!src2add action=accept chain=prerouting comment="" disabled=no dst-port=443 \in-interface=LAN protocol=tcpadd action=mark-connection chain=input comment="" disabled=no in-interface=\pppoe-out1 new-connection-mark=1 passthrough=yesadd action=mark-connection chain=input comment="" disabled=no in-interface=\pppoe-out2 new-connection-mark=2 passthrough=yesadd action=mark-connection chain=input comment="" disabled=no in-interface=\pppoe-out3 new-connection-mark=3 passthrough=yesadd action=mark-routing chain=output comment="" connection-mark=1 disabled=no \new-routing-mark=to_1 passthrough=yesadd action=mark-routing chain=output comment="" connection-mark=2 disabled=no \new-routing-mark=to_2 passthrough=yesadd action=mark-routing chain=output comment="" connection-mark=3 disabled=no \new-routing-mark=to_3 passthrough=yesadd action=mark-connection chain=prerouting comment="" disabled=no \dst-address-type=!local new-connection-mark=1 passthrough=yes \per-connection-classifier=both-addresses:3/0 src-address=10.0.0.0/24add action=mark-connection chain=prerouting comment="" disabled=no \dst-address-type=!local new-connection-mark=2 passthrough=yes \per-connection-classifier=both-addresses:3/1 src-address=10.0.0.0/24add action=mark-connection chain=prerouting comment="" disabled=no \dst-address-type=!local new-connection-mark=3 passthrough=yes \per-connection-classifier=both-addresses:3/2 src-address=10.0.0.0/24add action=mark-routing chain=prerouting comment="" connection-mark=1 \disabled=no new-routing-mark=to_1 passthrough=yes src-address=10.0.0.0/24add action=mark-routing chain=prerouting comment="" connection-mark=2 \disabled=no new-routing-mark=to_2 passthrough=yes src-address=10.0.0.0/24add action=mark-routing chain=prerouting comment="" connection-mark=3 \disabled=no new-routing-mark=to_3 passthrough=yes src-address=10.0.0.0/24以上是PPPOE 负载平衡，为both-addresses形式的（好像和PCC一样，不明白，还有就是我没做IP负载平衡，我用不着，做了也删了）add action=mark-connection chain=prerouting comment="" disabled=no dst-port=\8291 in-interface=pppoe-out3 new-connection-mark=in_3 passthrough=yes \protocol=tcpadd action=mark-routing chain=output comment="" connection-mark=in_3 \disabled=no new-routing-mark=3 passthrough=yes以上是指定外网访问ROS的线路和端口，我这样理解，具体也不明白add action=mark-connection chain=prerouting comment=\ "\D3\C5\CF\C8\B6\CB\BF\DA" disabled=no dst-port=443 new-connection-mark=\Port_Conn passthrough=yes protocol=tcpadd action=mark-connection chain=prerouting comment="" disabled=no dst-port=\3724 new-connection-mark=Port_Conn passthrough=yes protocol=tcpadd action=mark-connection chain=prerouting comment="" disabled=no dst-port=\8000 new-connection-mark=Port_Conn passthrough=yes protocol=udpadd action=mark-packet chain=prerouting comment="" connection-mark=Port_Conn \disabled=no new-packet-mark=Port_Packet passthrough=noadd action=mark-connection chain=prerouting comment="web\B6\CB\BF\DA" \disabled=no dst-port=80 new-connection-mark=80_Conn passthrough=yes \protocol=tcpadd action=mark-connection chain=prerouting comment="" disabled=no dst-port=\53 new-connection-mark=80_Conn passthrough=yes protocol=udpadd action=mark-packet chain=prerouting comment="" connection-mark=80_Conn \ disabled=no new-packet-mark=80_packet passthrough=noadd action=mark-connection chain=prerouting comment=\ "\C6\E4\CB\FB\CA\FD\BE\DD" disabled=no new-connection-mark=Other_Conn \passthrough=yesadd action=mark-packet chain=prerouting comment="" connection-mark=Other_Conn \ disabled=no new-packet-mark=Other_Packet passthrough=no以上是端口优先标记，和前面的一起使用，不用就都不要加/ip firewall natadd action=masquerade chain=srcnat comment=10 disabled=no out-interface=\pppoe-out1add action=masquerade chain=srcnat comment=11 disabled=no out-interface=\pppoe-out2add action=masquerade chain=srcnat comment=12 disabled=no out-interface=\pppoe-out3以上是IP伪装，我是三知AD，和2.9的不一样，开始这里按2.9的搞，搞了很久上不了网/ip firewall service-portset ftp disabled=no ports=21set tftp disabled=no ports=69set irc disabled=no ports=6667set h323 disabled=noset sip disabled=no ports=5060,5061set pptp disabled=no/ip neighbor discoveryset WAN3 discover=yesset LAN discover=yesset WAN1 discover=yesset WAN2 discover=yesset pppoe-out1 discover=noset pppoe-out2 discover=noset pppoe-out3 discover=no/ip proxyset always-from-cache=no cache-administrator=webmastercache-hit-dscp=4 \cache-on-disk=no enabled=no max-cache-size=none max-client-connections=\600 max-fresh-time=3d max-server-connections=600 parent-proxy=0.0.0.0 \parent-proxy-port=0 port=8080 serialize-connections=no src-address=\0.0.0.0以上是不知用的东东/ip routeadd check-gateway=ping comment="" disabled=yes distance=1 dst-address=\0.0.0.0/0 gateway=pppoe-out2 routing-mark=2add check-gateway=ping comment="" disabled=yes distance=1 dst-address=\0.0.0.0/0 gateway=pppoe-out3 routing-mark=3add check-gateway=ping comment="" disabled=yes distance=1 dst-address=\0.0.0.0/0 gateway=pppoe-out1add check-gateway=ping comment="" disabled=yes distance=1 dst-address=\0.0.0.0/0 gateway=pppoe-out1 routing-mark=1add check-gateway=ping comment="" disabled=yes distance=2 dst-address=\0.0.0.0/0 gateway=pppoe-out2add comment=WAN1 disabled=no distance=1 dst-address=0.0.0.0/0 gateway=\pppoe-out1 routing-mark=to_1add comment=WAN3 disabled=no distance=1 dst-address=0.0.0.0/0 gateway=\pppoe-out3 routing-mark=to_3add check-gateway=ping comment="" disabled=yes distance=2 dst-address=\0.0.0.0/0 gateway=pppoe-out1add check-gateway=ping comment=WAN2 disabled=no distance=10 dst-address=\0.0.0.0/0 gateway=pppoe-out2add check-gateway=ping comment="" disabled=yes distance=2 dst-address=\0.0.0.0/0 gateway=pppoe-out3add comment=WAN2 disabled=no distance=1 dst-address=0.0.0.0/0 gateway=\pppoe-out2 routing-mark=to_2add check-gateway=ping comment=WAN1 disabled=no distance=10 dst-address=\0.0.0.0/0 gateway=pppoe-out1add check-gateway=ping comment=WAN3 disabled=no distance=10 dst-address=\0.0.0.0/0 gateway=pppoe-out3以上这里就是路由了，看着有点长，设好后其实就只有3*2+1条了，为什么？我这样理解的，3条AD+3条备用+1条默认/ip serviceset telnet address=0.0.0.0/0 disabled=no port=23set ftp address=0.0.0.0/0 disabled=no port=21set www address=0.0.0.0/0 disabled=no port=80set www-ssl address=0.0.0.0/0 certificate=none disabled=yes port=443set api address=0.0.0.0/0 disabled=yes port=8728set winbox address=0.0.0.0/0 disabled=no port=8291/ip socksset connection-idle-timeout=2m enabled=no max-connections=200 port=1080/ip traffic-flowset active-flow-timeout=30m cache-entries=4k enabled=no \inactive-flow-timeout=15s interfaces=all/ip upnpset allow-disable-external-interface=yes enabled=yes show-dummy-rule=yes以上这些也是不知用的东东，也不用管吧/ppp aaaset accounting=yes interim-update=0s use-radius=no/ppp secretadd caller-id="" comment="" disabled=no limit-bytes-in=0 limit-bytes-out=0 \name=ADSC110 password=110110 profile=LOW routes="" service=anyadd caller-id="" comment="" disabled=no limit-bytes-in=0 limit-bytes-out=0 \name=ADSC207 password=207207 profile=default routes="" service=any以上是我拔号上网的用户名和密码，按自己的加，PPPOE服务前面已建立好了set WAN3 queue=ethernet-defaultset LAN queue=ethernet-defaultset WAN1 queue=ethernet-defaultset WAN2 queue=ethernet-defaultset pppoe-out1 queue=defaultset pppoe-out2 queue=defaultset pppoe-out3 queue=default/radius incomingset accept=no port=3799/storeadd comment="" disabled=no disk=primary-master name=web-proxy1 type=web-proxy /system clockset time-zone-name=manual/system clock manualset dst-delta=+00:00 dst-end="jan/01/1970 00:00:00" dst-start=\"jan/01/1970 00:00:00" time-zone=+00:00/system consoleadd disabled=no port=serial0 term=vt102set [ find vcno=1 ] disabled=no term=linuxset [ find vcno=2 ] disabled=no term=linuxset [ find vcno=3 ] disabled=no term=linuxset [ find vcno=4 ] disabled=no term=linuxset [ find vcno=5 ] disabled=no term=linuxset [ find vcno=6 ] disabled=no term=linuxset [ find vcno=7 ] disabled=no term=linuxset [ find vcno=8 ] disabled=no term=linux/system console screenset line-count=25/system hardwareset multi-cpu=yes/system healthset state-after-reboot=enabled/system identityset name=MikroTik/system loggingadd action=memory disabled=no prefix="" topics=infoadd action=memory disabled=no prefix="" topics=erroradd action=memory disabled=no prefix="" topics=warning add action=echo disabled=no prefix="" topics=critical/system noteset note="" show-at-login=yes/system ntp clientset enabled=no mode=broadcast primary-ntp=0.0.0.0 secondary-ntp=0.0.0.0上面的我也没搞明白是什么，也不用去理会/system scheduleradd comment="" disabled=no interval=30s name=getadsl on-event=":global assign\ \r\\n:global new\r\\n:global status\r\\n:global x\r\\n:set x 3\r\（红字3改成你的AD条数）\n:for i from=1 to=\$x do={\r\\n :set status [/interface get [/interface find name=(\"pppoe-out\" . \\$i)] running]\r\\n :if (\$status=true) do={\r\\n :set new [/ip address get [/ip address find dynamic=yes interface=(\\"pppoe-out\" . \$i)] address]\r\\n :set new [:pick \$new 0 ([:len \$new] -3)]\r\\n :set assign [/ip address get [/ip address find dynamic=no interface\=(\"pppoe-out\" . \$i)] address]\r\\n :set assign [:pick \$assign 0 ([:len \$assign] -3)]\r\\n :if (\$assign != \$new) do={ /ip address set [/ip addressfind c\omment=(\"adsl\" . \$i)] address=\$new network=\$new broadcast=\$new\r\\n /ip route set [/ip route find comment=(\"adsl\" . \$i)] gateway\=\$new\r\\n }\r\\n }\r\\n} \r\\n" start-time=startup以上是刷网关的脚本，很重点的哟add comment="" disabled=no interval=5m name=DDNS on-event=":log info \"DDNS: B\ egin\"\r\\n:global ddns-user \"123456\"\r\\n:global ddns-pass \"123456\"\r\\n:global ddns-host \"/doc/143656614.html,\"\r\（将红字改成你的）\n:global ddns-interface \"pppoe-out1\"\r\（这个是用那条线做DDNS）\n:global ddns-ip [ /ip address get [/ip address find interface=\$ddns-int\erface] address ] \r\\n:log info \"DDNS: Sending UPDATE!\"\r\\n:log info [ /tool dns-update name=\$ddns-host address=[:pick \$ddns-ip 0\\_[:find \$ddns-ip \"/\"] ] key-name=\$ddns-user key=\$ddns-pass ]\r\\n:log info \"DDNS: End\"" start-time=startup以上是DDNS,很好用的/system scriptadd name=ADSL policy=\ftp,reboot,read,write,policy,test,winbox,password,sniff,sensit ive source="\:global assign\r\\n:global new\r\\n:global status\r\\n:global x\r\\n:set x 2\r\\n:for i from=1 to=\$x do={\r\\n :set status [/interface get [/interface find name=(\"pppoe-out\" . \\$i)] running]\r\\n :if (\$status=true) do={\r\\n :set new [/ip address get [/ip address find dynamic=yes interface=(\\"pppoe-out\" . \$i)] address]\r\\n :set new [:pick \$new 0 ([:len \$new] -3)]\r\\n :set assign [/ip address get [/ip address find dynamic=no interface\=(\"pppoe-out\" . \$i)] address]\r\\n :set assign [:pick \$assign 0 ([:len \$assign] -3)]\r\\n :if (\$assign != \$new) do={ /ip address set [/ip address find c\omment=(\"adsl\" . \$i)] address=\$new network=\$new broadcast=\$new\r\\n /ip route set [/ip route find comment=(\"adsl\" . \$i)] gateway\=\$new\r\\n }\r\\n }\r\\n} \r\\n"/system upgrade mirrorset check-interval=1d enabled=no primary-server=0.0.0.0 secondary-server=\0.0.0.0 user=""/system watchdogset auto-send-supout=no automatic-supout=yes no-ping-delay=5m watch-address=\ none watchdog-timer=yes /tool bandwidth-serverset allocate-udp-ports-from=2000 authenticate=yes enabled=yes max-sessions=\ 100/tool e-mailset from=<> password="" server=0.0.0.0:25 username=""/tool graphingset page-refresh=300 store-every=5min/tool graphing interfaceadd allow-address=0.0.0.0/0 disabled=no interface=all store-on-disk=yes/tool mac-serveradd disabled=no interface=all/tool mac-server pingset enabled=yes/tool smsset allowed-number="" channel=0 keep-max-sms=0 receive-enabled=no secret="" /tool snifferset file-limit=10 file-name="" filter-address1=0.0.0.0/0:0-65535 \filter-address2=0.0.0.0/0:0-65535 filter-protocol=ip-only filter-stream=\yes interface=all memory-limit=10 only-headers=no streaming-enabled=no \ streaming-server=0.0.0.0/useradd address=0.0.0.0/0 comment="system default user" disabled=no group=full \ name=admin/user aaaset accounting=yes default-group=read interim-update=0s use-radius=no以上的我还是搞不懂的。

ROS教程及一些防火墙规则和IP限速脚本

ros2.96秋风破解版安装教程（修正版）昨天晚上做的教程，因为半夜思路不清晰，做出了一个错误的垃圾教程~首先向下载过教程的朋友道歉~ 这次经过测试给大家重新做个教程~也是刚才到网盟看了一下~贴子还浮在上面~不能对不起大家，所以，不能误导大家，还是乖乖的重新做一个吧~废话少说了~先把需要的软件和部分策略说一下。

ROS2.96秋风破解版下载（网吧电信光纤，大家手下留情！）网通路由表、防火墙策略、自动切换脚本。

（绿字的教程附带，蓝字的请自己下载。

）接下来是说下具体步骤~这样思路会明确一些~1。

安装ROS系统，并选择所有服务。

硬盘接到IDE1，光驱接到IDE0。

BIOS里设置光驱引导系统,我拿虚拟机做演示，顺便虚拟机的使用大家也看下吧！需要安装的服务，全部选择即可。

全选输入A，同意选择输入I，回车，询问你：注意啦，所有数据（功能），都要被安装（选择的），是否继续，输入Y即可。

它又询问，是否保存旧配置，输入N。

接下来开始创建分区，格式化硬盘，安装服务。

提示软件安装完成，按回车重起。

这里多说一句，虚拟机如果安装完ROS后，会自动从硬盘启动，但是真实的计算机，就还是在光驱启动，所以这时候大家该把光盘拿出来了，BIOS里改为硬盘启动，ROS就会独立启动了。

启动后又问了，是否检测硬盘。

通常不必检测了，因为耽误时间。

默认他自动选N。

我们也可以直接输入N的。

他自动选了。

呵呵~2。

登陆ROS，修改网卡名字、填写另外两块网卡的IP信息。

ROS启动好后，在ROS主机上输入账号admin密码为空。

回车。

输入命令/int pri 查看系统检测到几块网卡~电信+网通双线切换路由，当然应该是3块网卡，如果少了，请自行检查问题所在！输入命令/ip address （设置IP命令）输入命令add address=192.168.0.1/24 interface=ether1 设置路由IP，也就是网关~（内网的网关地址）（内网网卡）通常是靠近CPU的为内网网卡，也就是ether1好了，网关设置好了，那我们登陆http://192.168.0.1来下载Winbox刚才我安装过一次，有遗留信息的。

ROS常用脚本命令有哪些

2011、8、9 2011、5、28
2012、5、16 2012、2、5 女 3.2kg 顺产 40w 38w 男 3.45kg 剖腹产
流出流出 15149525369 13848545068
2010、9、20 2011、6、27 2011、6、27 2011、1、14 2011、10、21 2011、10、7
Hale Waihona Puke 女 3.15kg 3.0kg 2.5kg 3.7kg 3.4kg 3.1kg
3.8kg 剖腹产 40w+1
女 3.85kg
40w+2 2011、8、11转出
2010、10、11 2011、7、18 2011、7、14 2010、10、27 2011、7、4 2010、10、27 2011、7、4 2010、10、18 2011、7、25 2010、10、31 2011、8、7 2010、11、23 2011、9、1 2011、3、22 2011、12、29 2011、5、29 2012、3、6
3.3kg 剖腹产 39w+3
女 3.10kg 男 3.55kg
2010、10、13 2011、7、20 2011、7、20
3.3kg 剖腹产 41w+4 3.8kg 剖腹产
托那娃斯琴 29岁
张波陈蓉黄玉刘春艳
26岁 19岁 23岁 24岁
弘丰锆业三垧梁弘丰锆业三垧梁
G1P0 G1P0 G1P0 G1P0
孕产妇登记本
姓名郝巧花张瑞芳崔霞尚娜高蕊白艳霞何爱梅李小蓉何艳马玲蔺玉芬田二芬卢明英乌日娜王丽红乌兰图雅格鲁刘玉霞年龄 36岁 25岁 24岁 23岁 29岁 29岁 28岁 19岁 25岁 31岁 25岁 41岁 20岁 28岁 23岁 29岁 41岁 32岁家庭住址草原村草原村焦家圪卜草原村焦家圪卜草原村秦油坊草原村三座塔草原村二贵壕兴忠砖厂三垧梁陶尔斯草原村草原村三垧梁工厂草原村三座塔三垧梁草原村园子塔拉草原村释尼召草原村三垧梁草原村三座塔草原村三座塔草原村秦油坊孕产次 G2P1 G1P0 G1P0 G1P0 G2P1 G1P0 G1P0 G1P0 G3P2 G3P2 G2P1 G3P2 G2P0 G3P2 G1P0 G3P2 G2P1 G2P1 G2P1 末次月经预产期分娩日期性别体重分娩方式孕周 3.2Kg 顺产 40w 40w 40w 40w 40w+1 40w 40w 40w+6 40w-3 41w+2 41w+3 40w 40w 女男男女女男男男女女男 3.2Kg 剖腹产 305kg 剖腹产 3.6kg 剖腹产顺产顺产顺产顺产顺产顺产顺产顺产顺产联系电话 13214855313 15344022110 15947736573 13848799528 13451377829 15134873730 13530230784转出 2011、7、12转出 2011、8、2转出 15047743485 13134888165 15247391163 15134806061 15847474774 15924504880 13214855313 2010、1、13 2010、10、27 2010、10、27 男 2009、12、20 2010、10、4 2010、10、4 2010、6、21 2011、3、5 2011、3、5 2010、3、2 2010、12、16 2010、12、16 女 2010、7、13 2011、4、27 2011、4、28 2010、8、16 2011、5、30 2011、5、29 2010、9、2 2010、7、26 2010、7、25 2011、6、9 2011、5、3 2011、5、2 2011、6、9 2011、5、5 2011、5、8 2011、7、1 2011、7、13 2011、8、5 2011、8、18 2011、9、1 2010、7、18 2011、4、25 2011、4、25

Ros 3.30 PCC多线负载均衡脚本脚本

Ros 3.30 PCC双线负载均衡脚本脚本如下/ip address add address=内网网关IP/内网子网掩码interface=内网网卡名称comment="\D1\CC\C9\F1\B6\E0\CF\DF\50\43\43\BD\C5\B1\BE\52\6F\73\BC\BC\CA\F5\ BD\BB\C1\F7\C8\BA\A3\BA\31\30\32\38\37\32\30\35\38"/ip dns set primary-dns=首选DNS secondary-dns=备用DNS allow-remote-requests=yes /interface pppoe-client add name="pppoe-out1" interface=外网网卡1名称user="PPPoE 帐号1" password="密码1" add-default-route=no disabled=no/interface pppoe-client add name="pppoe-out2" interface=外网网卡2名称user="PPPoE 帐号2" password="密码2" add-default-route=no disabled=no/ip firewall mangleadd action=change-mss chain=forwardcomment="\D1\CC\C9\F1\B6\E0\CF\DF\50\43\43\BD\C5\B1\BE\52\6F\73\BC\BC\CA\F5\ BD\BB\C1\F7\C8\BA\A3\BA\31\30\32\38\37\32\30\35\38" disabled=no new-mss=1440 protocol=tcp tcp-flags=synadd action=mark-connection chain=input comment="" disabled=noin-interface=pppoe-out1 new-connection-mark=pppoe-out1_conn passthrough=yesadd action=mark-connection chain=input comment="" disabled=noin-interface=pppoe-out2 new-connection-mark=pppoe-out2_conn passthrough=yesadd action=mark-routing chain=output comment="" connection-mark=pppoe-out1_conn disabled=no new-routing-mark=to_pppoe-out1 passthrough=yesadd action=mark-routing chain=output comment="" connection-mark=pppoe-out2_conn disabled=no new-routing-mark=to_pppoe-out2 passthrough=yesadd action=mark-connection chain=prerouting comment="" disabled=nodst-address-type=!local in-interface=ether1 new-connection-mark=pppoe-out1_conn passthrough=yes per-connection-classifier=both-addresses:2/0 src-address=内网网断/内网子网掩码add action=mark-connection chain=prerouting comment="" disabled=nodst-address-type=!local in-interface=ether1 new-connection-mark=pppoe-out2_conn passthrough=yes per-connection-classifier=both-addresses:2/1 src-address=内网网断/内网子网掩码add action=mark-routing chain=prerouting comment=""connection-mark=pppoe-out1_conn disabled=no in-interface=ether1new-routing-mark=to_pppoe-out1 passthrough=yes src-address=内网网断/内网子网掩码add action=mark-routing chain=prerouting comment=""connection-mark=pppoe-out2_conn disabled=no in-interface=ether1new-routing-mark=to_pppoe-out2 passthrough=yes src-address=内网网断/内网子网掩码/ip routeadd comment=1 disabled=no distance=1 dst-address=0.0.0.0/0 gateway=pppoe-out1 routing-mark=to_pppoe-out1 check-gateway=pingadd comment=2 disabled=no distance=1 dst-address=0.0.0.0/0 gateway=pppoe-out2 routing-mark=to_pppoe-out2 check-gateway=pingadd check-gateway=ping comment="pppoe-out1" disabled=no distance=10dst-address=0.0.0.0/0 gateway=pppoe-out1add check-gateway=ping comment="pppoe-out2" disabled=no distance=10dst-address=0.0.0.0/0 gateway=pppoe-out2/ip firewall natadd action=masquerade chain=srcnat comment="1" disabled=noout-interface=pppoe-out1add action=masquerade chain=srcnat comment="2" disabled=noout-interface=pppoe-out2Ros 3.30 PCC三线负载均衡脚本脚本如下/ip address add address=内网网关IP/内网子网掩码interface=内网网卡名称comment="\D1\CC\C9\F1\B6\E0\CF\DF\50\43\43\BD\C5\B1\BE\52\6F\73\BC\BC\CA\F5\ BD\BB\C1\F7\C8\BA\A3\BA\31\30\32\38\37\32\30\35\38"/ip dns set primary-dns=首选DNS secondary-dns=备用DNS allow-remote-requests=yes /interface pppoe-client add name="pppoe-out1" interface=外网网卡1名称user="PPPoE 帐号1" password="密码1" add-default-route=no disabled=no/interface pppoe-client add name="pppoe-out2" interface=外网网卡2名称user="PPPoE 帐号2" password="密码2" add-default-route=no disabled=no/interface pppoe-client add name="pppoe-out3" interface=外网网卡3名称user="PPPoE 帐号3" password="密码3" add-default-route=no disabled=no/ip firewall mangleadd action=change-mss chain=forwardcomment="\D1\CC\C9\F1\B6\E0\CF\DF\50\43\43\BD\C5\B1\BE\52\6F\73\BC\BC\CA\F5\ BD\BB\C1\F7\C8\BA\A3\BA\31\30\32\38\37\32\30\35\38" disabled=no new-mss=1440 protocol=tcp tcp-flags=synadd action=mark-connection chain=input comment="" disabled=noin-interface=pppoe-out1 new-connection-mark=pppoe-out1_conn passthrough=yesadd action=mark-connection chain=input comment="" disabled=noin-interface=pppoe-out2 new-connection-mark=pppoe-out2_conn passthrough=yesadd action=mark-connection chain=input comment="" disabled=noin-interface=pppoe-out3 new-connection-mark=pppoe-out3_conn passthrough=yesadd action=mark-routing chain=output comment="" connection-mark=pppoe-out1_conn disabled=no new-routing-mark=to_pppoe-out1 passthrough=yesadd action=mark-routing chain=output comment="" connection-mark=pppoe-out2_conn disabled=no new-routing-mark=to_pppoe-out2 passthrough=yesadd action=mark-routing chain=output comment="" connection-mark=pppoe-out3_conn disabled=no new-routing-mark=to_pppoe-out3 passthrough=yesadd action=mark-connection chain=prerouting comment="" disabled=nodst-address-type=!local in-interface=ether1 new-connection-mark=pppoe-out1_conn passthrough=yes per-connection-classifier=both-addresses:3/0 src-address=内网网断/内网子网掩码add action=mark-connection chain=prerouting comment="" disabled=nodst-address-type=!local in-interface=ether1 new-connection-mark=pppoe-out2_conn passthrough=yes per-connection-classifier=both-addresses:3/1 src-address=内网网断/内网子网掩码add action=mark-connection chain=prerouting comment="" disabled=nodst-address-type=!local in-interface=ether1 new-connection-mark=pppoe-out3_conn passthrough=yes per-connection-classifier=both-addresses:3/2 src-address=内网网断/内网子网掩码add action=mark-routing chain=prerouting comment=""connection-mark=pppoe-out1_conn disabled=no in-interface=ether1new-routing-mark=to_pppoe-out1 passthrough=yes src-address=内网网断/内网子网掩码add action=mark-routing chain=prerouting comment=""connection-mark=pppoe-out2_conn disabled=no in-interface=ether1new-routing-mark=to_pppoe-out2 passthrough=yes src-address=内网网断/内网子网掩码add action=mark-routing chain=prerouting comment=""connection-mark=pppoe-out3_conn disabled=no in-interface=ether1new-routing-mark=to_pppoe-out3 passthrough=yes src-address=内网网断/内网子网掩码/ip routeadd comment=1 disabled=no distance=1 dst-address=0.0.0.0/0 gateway=pppoe-out1 routing-mark=to_pppoe-out1 check-gateway=pingadd comment=2 disabled=no distance=1 dst-address=0.0.0.0/0 gateway=pppoe-out2 routing-mark=to_pppoe-out2 check-gateway=pingadd comment=3 disabled=no distance=1 dst-address=0.0.0.0/0 gateway=pppoe-out3 routing-mark=to_pppoe-out3 check-gateway=pingadd check-gateway=ping comment="pppoe-out1" disabled=no distance=10dst-address=0.0.0.0/0 gateway=pppoe-out1add check-gateway=ping comment="pppoe-out2" disabled=no distance=10dst-address=0.0.0.0/0 gateway=pppoe-out2add check-gateway=ping comment="pppoe-out3" disabled=no distance=10dst-address=0.0.0.0/0 gateway=pppoe-out3/ip firewall natadd action=masquerade chain=srcnat comment="1" disabled=noout-interface=pppoe-out1add action=masquerade chain=srcnat comment="2" disabled=noout-interface=pppoe-out2add action=masquerade chain=srcnat comment="3" disabled=noout-interface=pppoe-out3Ros 3.30 PCC四线负载均衡脚本脚本如下/ip address add address=内网网关IP/内网子网掩码interface=内网网卡名称comment="\D1\CC\C9\F1\B6\E0\CF\DF\50\43\43\BD\C5\B1\BE\52\6F\73\BC\BC\CA\F5\ BD\BB\C1\F7\C8\BA\A3\BA\31\30\32\38\37\32\30\35\38"/ip dns set primary-dns=首选DNS secondary-dns=备用DNS allow-remote-requests=yes /interface pppoe-client add name="pppoe-out1" interface=外网网卡1名称user="PPPoE 帐号1" password="密码1" add-default-route=no disabled=no/interface pppoe-client add name="pppoe-out2" interface=外网网卡2名称user="PPPoE 帐号2" password="密码2" add-default-route=no disabled=no/interface pppoe-client add name="pppoe-out3" interface=外网网卡3名称user="PPPoE 帐号3" password="密码3" add-default-route=no disabled=no/interface pppoe-client add name="pppoe-out4" interface=外网网卡4名称user="PPPoE 帐号4" password="密码4" add-default-route=no disabled=no/ip firewall mangleadd action=change-mss chain=forwardcomment="\D1\CC\C9\F1\B6\E0\CF\DF\50\43\43\BD\C5\B1\BE\52\6F\73\BC\BC\CA\F5\ BD\BB\C1\F7\C8\BA\A3\BA\31\30\32\38\37\32\30\35\38" disabled=no new-mss=1440 protocol=tcp tcp-flags=synadd action=mark-connection chain=input comment="" disabled=noin-interface=pppoe-out1 new-connection-mark=pppoe-out1_conn passthrough=yesadd action=mark-connection chain=input comment="" disabled=noin-interface=pppoe-out2 new-connection-mark=pppoe-out2_conn passthrough=yesadd action=mark-connection chain=input comment="" disabled=noin-interface=pppoe-out3 new-connection-mark=pppoe-out3_conn passthrough=yesadd action=mark-connection chain=input comment="" disabled=noin-interface=pppoe-out4 new-connection-mark=pppoe-out4_conn passthrough=yesadd action=mark-routing chain=output comment="" connection-mark=pppoe-out1_conn disabled=no new-routing-mark=to_pppoe-out1 passthrough=yesadd action=mark-routing chain=output comment="" connection-mark=pppoe-out2_conn disabled=no new-routing-mark=to_pppoe-out2 passthrough=yesadd action=mark-routing chain=output comment="" connection-mark=pppoe-out3_conn disabled=no new-routing-mark=to_pppoe-out3 passthrough=yesadd action=mark-routing chain=output comment="" connection-mark=pppoe-out4_conn disabled=no new-routing-mark=to_pppoe-out4 passthrough=yesadd action=mark-connection chain=prerouting comment="" disabled=nodst-address-type=!local in-interface=ether1 new-connection-mark=pppoe-out1_conn passthrough=yes per-connection-classifier=both-addresses:4/0 src-address=内网网断/内网子网掩码add action=mark-connection chain=prerouting comment="" disabled=nodst-address-type=!local in-interface=ether1 new-connection-mark=pppoe-out2_conn passthrough=yes per-connection-classifier=both-addresses:4/1 src-address=内网网断/内网子网掩码add action=mark-connection chain=prerouting comment="" disabled=nodst-address-type=!local in-interface=ether1 new-connection-mark=pppoe-out3_conn passthrough=yes per-connection-classifier=both-addresses:4/2 src-address=内网网断/内网子网掩码add action=mark-connection chain=prerouting comment="" disabled=nodst-address-type=!local in-interface=ether1 new-connection-mark=pppoe-out4_conn passthrough=yes per-connection-classifier=both-addresses:4/3 src-address=内网网断/内网子网掩码add action=mark-routing chain=prerouting comment=""connection-mark=pppoe-out1_conn disabled=no in-interface=ether1new-routing-mark=to_pppoe-out1 passthrough=yes src-address=内网网断/内网子网掩码add action=mark-routing chain=prerouting comment=""connection-mark=pppoe-out2_conn disabled=no in-interface=ether1new-routing-mark=to_pppoe-out2 passthrough=yes src-address=内网网断/内网子网掩码add action=mark-routing chain=prerouting comment=""connection-mark=pppoe-out3_conn disabled=no in-interface=ether1new-routing-mark=to_pppoe-out3 passthrough=yes src-address=内网网断/内网子网掩码add action=mark-routing chain=prerouting comment=""connection-mark=pppoe-out3_conn disabled=no in-interface=ether1new-routing-mark=to_pppoe-out4 passthrough=yes src-address=内网网断/内网子网掩码/ip routeadd comment=1 disabled=no distance=1 dst-address=0.0.0.0/0 gateway=pppoe-out1 routing-mark=to_pppoe-out1 check-gateway=pingadd comment=2 disabled=no distance=1 dst-address=0.0.0.0/0 gateway=pppoe-out2 routing-mark=to_pppoe-out2 check-gateway=pingadd comment=3 disabled=no distance=1 dst-address=0.0.0.0/0 gateway=pppoe-out3 routing-mark=to_pppoe-out3 check-gateway=pingadd comment=4 disabled=no distance=1 dst-address=0.0.0.0/0 gateway=pppoe-out4 routing-mark=to_pppoe-out4 check-gateway=pingadd check-gateway=ping comment="pppoe-out1" disabled=no distance=10dst-address=0.0.0.0/0 gateway=pppoe-out1add check-gateway=ping comment="pppoe-out2" disabled=no distance=10dst-address=0.0.0.0/0 gateway=pppoe-out2add check-gateway=ping comment="pppoe-out3" disabled=no distance=10dst-address=0.0.0.0/0 gateway=pppoe-out3add check-gateway=ping comment="pppoe-out4" disabled=no distance=10dst-address=0.0.0.0/0 gateway=pppoe-out4/ip firewall natadd action=masquerade chain=srcnat comment="1" disabled=noout-interface=pppoe-out1add action=masquerade chain=srcnat comment="2" disabled=noout-interface=pppoe-out2add action=masquerade chain=srcnat comment="3" disabled=noout-interface=pppoe-out3add action=masquerade chain=srcnat comment="4" disabled=noout-interface=pppoe-out4Ros 3.30 PCC五线负载均衡脚本脚本如下/ip address add address=内网网关IP/内网子网掩码interface=内网网卡名称comment="\D1\CC\C9\F1\B6\E0\CF\DF\50\43\43\BD\C5\B1\BE\52\6F\73\BC\BC\CA\F5\ BD\BB\C1\F7\C8\BA\A3\BA\31\30\32\38\37\32\30\35\38"/ip dns set primary-dns=首选DNS secondary-dns=备用DNS allow-remote-requests=yes /interface pppoe-client add name="pppoe-out1" interface=外网网卡1名称user="PPPoE 帐号1" password="密码1" add-default-route=no disabled=no/interface pppoe-client add name="pppoe-out2" interface=外网网卡2名称user="PPPoE 帐号2" password="密码2" add-default-route=no disabled=no/interface pppoe-client add name="pppoe-out3" interface=外网网卡3名称user="PPPoE 帐号3" password="密码3" add-default-route=no disabled=no/interface pppoe-client add name="pppoe-out4" interface=外网网卡4名称user="PPPoE 帐号4" password="密码4" add-default-route=no disabled=no/interface pppoe-client add name="pppoe-out5" interface=外网网卡5名称user="PPPoE 帐号5" password="密码5" add-default-route=no disabled=no/ip firewall mangleadd action=change-mss chain=forwardcomment="\D1\CC\C9\F1\B6\E0\CF\DF\50\43\43\BD\C5\B1\BE\52\6F\73\BC\BC\CA\F5\ BD\BB\C1\F7\C8\BA\A3\BA\31\30\32\38\37\32\30\35\38" disabled=no new-mss=1440 protocol=tcp tcp-flags=synadd action=mark-connection chain=input comment="" disabled=noin-interface=pppoe-out1 new-connection-mark=pppoe-out1_conn passthrough=yesadd action=mark-connection chain=input comment="" disabled=noin-interface=pppoe-out2 new-connection-mark=pppoe-out2_conn passthrough=yesadd action=mark-connection chain=input comment="" disabled=noin-interface=pppoe-out3 new-connection-mark=pppoe-out3_conn passthrough=yesadd action=mark-connection chain=input comment="" disabled=noin-interface=pppoe-out4 new-connection-mark=pppoe-out4_conn passthrough=yesadd action=mark-connection chain=input comment="" disabled=noin-interface=pppoe-out5 new-connection-mark=pppoe-out5_conn passthrough=yesadd action=mark-routing chain=output comment="" connection-mark=pppoe-out1_conn disabled=no new-routing-mark=to_pppoe-out1 passthrough=yesadd action=mark-routing chain=output comment="" connection-mark=pppoe-out2_conn disabled=no new-routing-mark=to_pppoe-out2 passthrough=yesadd action=mark-routing chain=output comment="" connection-mark=pppoe-out3_conn disabled=no new-routing-mark=to_pppoe-out3 passthrough=yesadd action=mark-routing chain=output comment="" connection-mark=pppoe-out4_conn disabled=no new-routing-mark=to_pppoe-out4 passthrough=yesadd action=mark-routing chain=output comment="" connection-mark=pppoe-out5_conn disabled=no new-routing-mark=to_pppoe-out5 passthrough=yesadd action=mark-connection chain=prerouting comment="" disabled=nodst-address-type=!local in-interface=ether1 new-connection-mark=pppoe-out1_conn passthrough=yes per-connection-classifier=both-addresses:5/0 src-address=内网网断/内网子网掩码add action=mark-connection chain=prerouting comment="" disabled=nodst-address-type=!local in-interface=ether1 new-connection-mark=pppoe-out2_conn passthrough=yes per-connection-classifier=both-addresses:5/1 src-address=内网网断/内网子网掩码add action=mark-connection chain=prerouting comment="" disabled=nodst-address-type=!local in-interface=ether1 new-connection-mark=pppoe-out3_conn passthrough=yes per-connection-classifier=both-addresses:5/2 src-address=内网网断/内网子网掩码add action=mark-connection chain=prerouting comment="" disabled=nodst-address-type=!local in-interface=ether1 new-connection-mark=pppoe-out4_conn passthrough=yes per-connection-classifier=both-addresses:5/3 src-address=内网网断/内网子网掩码add action=mark-connection chain=prerouting comment="" disabled=nodst-address-type=!local in-interface=ether1 new-connection-mark=pppoe-out5_conn passthrough=yes per-connection-classifier=both-addresses:5/4 src-address=内网网断/内网子网掩码add action=mark-routing chain=prerouting comment=""connection-mark=pppoe-out1_conn disabled=no in-interface=ether1new-routing-mark=to_pppoe-out1 passthrough=yes src-address=内网网断/内网子网掩码add action=mark-routing chain=prerouting comment=""connection-mark=pppoe-out2_conn disabled=no in-interface=ether1new-routing-mark=to_pppoe-out2 passthrough=yes src-address=内网网断/内网子网掩码add action=mark-routing chain=prerouting comment=""connection-mark=pppoe-out3_conn disabled=no in-interface=ether1new-routing-mark=to_pppoe-out3 passthrough=yes src-address=内网网断/内网子网掩码add action=mark-routing chain=prerouting comment=""connection-mark=pppoe-out3_conn disabled=no in-interface=ether1new-routing-mark=to_pppoe-out4 passthrough=yes src-address=内网网断/内网子网掩码add action=mark-routing chain=prerouting comment=""connection-mark=pppoe-out3_conn disabled=no in-interface=ether1new-routing-mark=to_pppoe-out5 passthrough=yes src-address=内网网断/内网子网掩码/ip routeadd comment=1 disabled=no distance=1 dst-address=0.0.0.0/0 gateway=pppoe-out1 routing-mark=to_pppoe-out1 check-gateway=pingadd comment=2 disabled=no distance=1 dst-address=0.0.0.0/0 gateway=pppoe-out2 routing-mark=to_pppoe-out2 check-gateway=pingadd comment=3 disabled=no distance=1 dst-address=0.0.0.0/0 gateway=pppoe-out3 routing-mark=to_pppoe-out3 check-gateway=pingadd comment=4 disabled=no distance=1 dst-address=0.0.0.0/0 gateway=pppoe-out4 routing-mark=to_pppoe-out4 check-gateway=pingadd comment=5 disabled=no distance=1 dst-address=0.0.0.0/0 gateway=pppoe-out5 routing-mark=to_pppoe-out5 check-gateway=pingadd check-gateway=ping comment="pppoe-out1" disabled=no distance=10dst-address=0.0.0.0/0 gateway=pppoe-out1add check-gateway=ping comment="pppoe-out2" disabled=no distance=10dst-address=0.0.0.0/0 gateway=pppoe-out2add check-gateway=ping comment="pppoe-out3" disabled=no distance=10dst-address=0.0.0.0/0 gateway=pppoe-out3add check-gateway=ping comment="pppoe-out4" disabled=no distance=10dst-address=0.0.0.0/0 gateway=pppoe-out4add check-gateway=ping comment="pppoe-out5" disabled=no distance=10dst-address=0.0.0.0/0 gateway=pppoe-out5/ip firewall natadd action=masquerade chain=srcnat comment="1" disabled=noout-interface=pppoe-out1add action=masquerade chain=srcnat comment="2" disabled=noout-interface=pppoe-out2add action=masquerade chain=srcnat comment="3" disabled=noout-interface=pppoe-out3add action=masquerade chain=srcnat comment="4" disabled=noout-interface=pppoe-out4add action=masquerade chain=srcnat comment="5" disabled=noout-interface=pppoe-out5。

网吧用ROS最正确的限速

网吧用ROS最正确的限速网吧用简单队列做限速完全是扯蛋。

网吧限速最好的办法应该是带宽均分，然后在用简单队列来限制上传。

在利用小包优先来处理游戏卡的问题。

经过2个网吧，一个月的测试，完全摆脱了到处喊卡的噩梦，现在把经验发来大家分享一下。

ROS不要用简单队列来限速，什么智能动态限速也不要用。

只需要用小包优先+带宽均分+简单队列限制上传速度。

小包优先的脚本如下：1./ ip firewall mangle2.add chain=forward protocol=tcp tcp-flags=syn action=change-mss new-mss=1440 comment="" disabled=no3.add chain=forward p2p=all-p2p action=mark-connection new-connection-mark=p2p_conn passthrough=yes comment="" disabled=no4.add chain=forward connection-mark=p2p_conn action=mark-packet new-packet-mark=p2p passthrough=yes comment="" disabled=no5.add chain=forward connection-mark=!p2p_conn action=mark-packet new-packet-mark=general passthrough=yes comment=""6.7.disabled=no8.add chain=forward packet-size=32-512 action=mark-packet new-packet-mark=all passthrough=yes comment="" disabled=no9.add chain=forward packet-size=512-1200 action=mark-packet new-packet-mark=big passthrough=yes comment=""disabled=no10.11.12./ queue tree13.add name="p2p1" parent=wan packet-mark=p2p limit-at=2000000 queue=default priority=8 max-limit=6000000 burst-limit=014.15.burst-threshold=0 burst-time=0s disabled=no16.add name="p2p2" parent=lan packet-mark=p2p limit-at=2000000 queue=default priority=8 max-limit=6000000 burst-limit=017.18.burst-threshold=0 burst-time=0s disabled=no19.add name="ClassA" parent=lan packet-mark="" limit-at=0 queue=default priority=8 max-limit=100000000 burst-limit=0 burst-20.21.threshold=0 burst-time=0s disabled=no22.add name="ClassB" parent=ClassA packet-mark="" limit-at=0 queue=default priority=8 max-limit=0 burst-limit=0 burst-23.24.threshold=0 burst-time=0s disabled=no25.add name="Leaf1" parent=ClassA packet-mark=general limit-at=0 queue=default priority=7 max-limit=0 burst-limit=0 burst-26.27.threshold=0 burst-time=0s disabled=no28.add name="Leaf2" parent=ClassB packet-mark=alllimit-at=0 queue=default priority=5 max-limit=0 burst-limit=0 burst-29.30.threshold=0 burst-time=0s disabled=no31.add name="Leaf3" parent=ClassB packet-mark=big limit-at=0 queue=default priority=6 max-limit=0 burst-limit=0 burst-32.33.threshold=0 burst-time=0s disabled=no复制代码然后是带宽均分：1./ ip firewall mangle add chain=forward src-address=192.168.0.0/24 \2.action=mark-connection new-connection-mark=users-con3./ip firewall mangle add connection-mark=users-con action=mark-packet \4.new-packet-mark=users chain=forward5./queue type add name=pcq-download kind=pcq pcq-classifier=dst-address6./queue type add name=pcq-upload kind=pcq pcq-classifier=src-address7./queue tree add name=Download parent=lan max-limit=10M8./queue tree add parent=Download queue=pcq-download packet-mark=users9./queue tree add name=Upload parent=wan max-limit=9M10./queue tree add parent=Upload queue=pcq-upload packet-mark=users复制代码请根据直接实际修改IP地址段，下载最大速度，上传最大速度,lan为我连接内网的网卡，wan是我连接外网的网卡限制上传速度的脚本：1.:for aaa from 5 to 253 do={/queue simple add name=(yp . $aaa) dst-address=(192.168.0. . $aaa) limit-at=10000000/30000002.3.max-limit=10000000/3000000}复制代码如果是3.2版本的，这个脚本自己要修改下，就用这3个部分，别的不需要的，绝对比什么智能动态限速好的多.。

cf跳ping调法

右键单击我的电脑，点击属性，再点击高级，然后点击性能栏的设置，调整为最佳性能’2下面我来教你怎么样提高网速：
使用宽带上网的自然比普通拨号的上网快了很多,可是WINDOWS XP系统会自动保留一部分宽带,有点浪费.利用起来吧.
单击开始→运行.
在对话框中输入"gpedit.msc"
单击确定进入WINDOWS XP 组策略编辑器,
在本地计算机策略中.逐一双击
" 计算机配置 → 管理摸版 → 网络 → QoS数据包计划程序 "
双击右侧窗口中的"限制可保留带宽"
在"已启用"前面的圆圈点一下,并将带宽限制由默认的20%改为0%.点确定就可以使宽带的利用率达到最高另外你家周围有没有什么新的强磁场设施的存在,那也会有影响.但愿你早点拜托这个问题,跳PING实在太痛苦了,不是一般人过的日子3建议你去下载<迅游> 这个软件，是专门优化游戏的Ping值的，很好用，你去试一试

ros调试方法

ros调试方法【最新版3篇】《ros调试方法》篇1ROS (Robot Operating System) 是一个广泛使用的机器人软件框架，用于开发和部署机器人应用程序。

在开发ROS 应用程序时，调试是非常重要的环节，以下是一些常用的ROS 调试方法：1. 断点调试断点调试是一种常见的调试方法，可以在代码中设置断点，使程序在执行到断点时停止。

可以使用ROS 提供的rostop 命令在代码中设置断点，如下所示：```rostop -r <rate> /<topic_name> <message_type> <message_data> ```其中，`<rate>` 是断点的触发率，`<topic_name>` 是要触发断点的话题名称，`<message_type>` 是消息类型，`<message_data>` 是消息数据。

例如，要在话题`/cmd_vel` 上设置一个触发率为100 Hz 的断点，可以使用以下命令：```rostop -r 100 /cmd_vel sensor_msgs/Joy```2. 监视变量ROS 提供了一种监视变量的方法，可以使用`rostop` 命令的`-m` 选项来监视变量。

例如，要监视`/cmd_vel` 话题上的传感器数据，可以使用以下命令：```rostop -m <topic_name> <message_type>```其中，`<topic_name>` 是要监视的话题名称，`<message_type>` 是消息类型。

例如，要监视`/cmd_vel` 话题上的传感器数据，可以使用以下命令：```rostop -m /cmd_vel sensor_msgs/Joy```3. 日志记录ROS 使用了log4cxx 库来记录日志，可以通过修改`rosconfig.yaml` 文件来配置日志记录级别。

可以优化解决大型网络游戏卡的ROS限速脚本

可以优化解决大型网络游戏卡的ROS限速脚本ros软路由一直是网吧用的比较多的软路由。

的确，ros防ddos攻击还是比较有用的。

网上有很多的ros软路由教程，今天这个算是ros限速脚本吧。

安装就不说了，大家可以参照网上很多的ros软路由教程来安装。

这个ros限速脚本事针对大型网络游戏卡而写的。

ip firewall mangleadd chain=forward p2p=all-p2p action=mark-connection \new-connection-mark=p2p_conn passthrough=yes comment=""disabled=noadd chain=forward connection-mark=p2p_conn action=mark-packet \new-packet-mark=p2p passthrough=yes comment="" disabled=noadd chain=forward connection-mark=!p2p_conn action=mark-packet \new-packet-mark=general passthrough=yes comment="" disabled=no add chain=forward packet-size=32-512 action=mark-packetnew-packet-mark=all \passthrough=yes comment="" disabled=noadd chain=forward packet-size=512-1200 action=mark-packetnew-packet-mark=big \passthrough=yes comment="" disabled=noadd chain=forward connection-mark=p2p_conn action=mark-packet \new-packet-mark=p2p passthrough=yes comment="" disabled=noadd chain=forward p2p=all-p2p action=mark-connection \new-connection-mark=p2p_conn passthrough=yes comment=""disabled=noadd chain=forward connection-mark=!p2p_conn action=mark-packet \new-packet-mark=general passthrough=yes comment="" disabled=no add chain=forward packet-size=32-512 action=mark-packetnew-packet-mark=all \passthrough=yes comment="" disabled=noadd chain=forward packet-size=512-1200 action=mark-packetnew-packet-mark=big \passthrough=yes comment="" disabled=noadd chain=forward p2p=all-p2p action=mark-connection \new-connection-mark=p2p_conn passthrough=yes comment=""disabled=noadd chain=forward connection-mark=p2p_conn action=mark-packet \new-packet-mark=p2p passthrough=yes comment="" disabled=noadd chain=forward connection-mark=!p2p_conn action=mark-packet \new-packet-mark=general passthrough=yes comment="" disabled=no add chain=forward packet-size=32-512 action=mark-packetnew-packet-mark=all \passthrough=yes comment="" disabled=noadd chain=forward packet-size=512-1200 action=mark-packetnew-packet-mark=big \passthrough=yes comment="" disabled=noadd chain=forward p2p=all-p2p action=mark-connection \new-connection-mark=p2p_conn passthrough=yes comment="" disabled=noadd chain=forward connection-mark=p2p_conn action=mark-packet \new-packet-mark=p2p passthrough=yes comment="" disabled=noadd chain=forward connection-mark=!p2p_conn action=mark-packet \new-packet-mark=general passthrough=yes comment="" disabled=no add chain=forward packet-size=32-512 action=mark-packetnew-packet-mark=all \passthrough=yes comment="" disabled=noadd chain=forward packet-size=512-1200 action=mark-packetnew-packet-mark=big \passthrough=yes comment="" disabled=noadd chain=forward p2p=all-p2p action=mark-connection \new-connection-mark=p2p_conn passthrough=yes comment="" disabled=noadd chain=forward connection-mark=p2p_conn action=mark-packet \new-packet-mark=p2p passthrough=yes comment="" disabled=noadd chain=forward connection-mark=!p2p_conn action=mark-packet \new-packet-mark=general passthrough=yes comment="" disabled=no add chain=forward packet-size=32-512 action=mark-packetnew-packet-mark=all \passthrough=yes comment="" disabled=noadd chain=forward packet-size=512-1200 action=mark-packetnew-packet-mark=big \passthrough=yes comment="" disabled=noadd chain=forward p2p=all-p2p action=mark-connection \new-connection-mark=p2p_conn passthrough=yes comment="" disabled=noadd chain=forward connection-mark=p2p_conn action=mark-packet \new-packet-mark=p2p passthrough=yes comment="" disabled=noadd chain=forward connection-mark=!p2p_conn action=mark-packet \new-packet-mark=general passthrough=yes comment="" disabled=no add chain=forward packet-size=32-512 action=mark-packetnew-packet-mark=all \passthrough=yes comment="" disabled=noadd chain=forward packet-size=512-1200 action=mark-packetnew-packet-mark=big \passthrough=yes comment="" disabled=noadd chain=forward p2p=all-p2p action=mark-connection \new-connection-mark=p2p_conn passthrough=yes comment="" disabled=noadd chain=forward connection-mark=p2p_conn action=mark-packet \new-packet-mark=p2p passthrough=yes comment="" disabled=noadd chain=forward connection-mark=!p2p_conn action=mark-packet \new-packet-mark=general passthrough=yes comment="" disabled=no add chain=forward packet-size=32-512 action=mark-packetnew-packet-mark=all \passthrough=yes comment="" disabled=noadd chain=forward packet-size=512-1200 action=mark-packetnew-packet-mark=big \passthrough=yes comment="" disabled=noadd chain=forward p2p=all-p2p action=mark-connection \new-connection-mark=p2p_conn passthrough=yes comment="" disabled=noadd chain=forward connection-mark=p2p_conn action=mark-packet \new-packet-mark=p2p passthrough=yes comment="" disabled=noadd chain=forward connection-mark=!p2p_conn action=mark-packet \new-packet-mark=general passthrough=yes comment="" disabled=no add chain=forward packet-size=32-512 action=mark-packetnew-packet-mark=all \passthrough=yes comment="" disabled=noadd chain=forward packet-size=512-1200 action=mark-packetnew-packet-mark=big \passthrough=yes comment="" disabled=no直接复制上面。

ROS 完美限制速度

Name(脚本名程)
Source(脚本)
OK-选择要运行的脚本-Run Script
ROS限速的极致应用
一般我们用ros限速只是使用了max-limit，其实ros限速可以更好的运用。比如我们希望
客户打开网页时速度可以快一些，下载时速度可以慢一些。ros2.9就可以实现。
max-limit------我们最常用的地方，最大速度
General-In. Interface all(如果你是拨号的就选择pppoe的、固定IP选择all即可）
Dst. Address:外网IP/32
Dst. Port:要映射的端口
Protocol:tcp(如果映射反恐的就用udp)
Action action:nat
TO Dst.Addresses:你的内网IP
$aaa)]}）
脚本名：node_off
脚本内容：（:for aaa from 1 to 254 do={/queue sim dis [find name=(ip_ .
$aaa)]}）
scripts（脚本部分）以完成
打开 /tools/traffic monitor
新建：
名：node_18M traffic=received trigger=above on event=node_on
2 to 254是2~254
192.168.0. . $aaa是IP
上两句加起来是192.168.0.2~192.168.0.254
connection-limit=50是线程数这里为50
max-limit=2000000/2000000是上行／下行
使用：
WinBox-System-Scripts-＋

ROS软路由限速脚本

queue=PCQ-up/PCQ-down limit-at=0/0 max-limit=15000000/15000000 \
total-queue=default-small disabled=yes
到这里就是建立动态限速的策略了！192.168.0.0/24 改为你IP段！max-limit=15000000/15000000 这里
把最后一段替换成这段就是由时间段控制开关PCQ了！
add name="PCQON" interface=WAN traffic=received trigger=above \
threshold=14800000 on-event=PCQON comment="" disabled=no
add name="PCQOFF" interface=WAN traffic=received trigger=below \
的静态限速，这样一算，1.5*5=7.5M了，再加上玩网游的人，基本上就稳定在10M左右了！
然后再设置一个脚本，当总流量少于6M的话（也就算没那么多人下载了，流量下来了）那么1.5M的静态限
速脚本就会自动关闭，又打开了本来3M的限速了！
基本上原理就是这样。通过这个原理，网吧宽带利用就会越来越合理！
/system scheduler add name=timeoff interval=24h start-time=23:59:59 on-event={PCQOFF}
disabled=no
==============================================================
add name="PCQ-down" kind=pcq pcq-rate=1500000 pcq-limit=50 \

发一个能用的ros智能限速脚本和调试说明

发一个能用的ros智能限速脚本和调试说明申明：此脚本不是我写的，也是在这里找的，具体是哪位兄弟写的不知道了，帖子也找不到了，在这里要感谢那位兄弟。

以前下回来操作没成功就放弃了，昨天晚上研究了3个小时终于能用了。

现在把详细调试说明写下来，我的版本是2.927，其他版本未做测试。

--------------脚本开始，请按照下面修改说明，把限制速度修改好后，再一并导入----------:for szwm from 1 to 253 do={/queue simple add name=(TX . $szwm) target-addresses=(192.168.1. . $szwm) max-limit=500000/500000 interface=lan disabled=no} / ip firewall mangle add chain=prerouting action=mark-packet new-packet-mark=all-mark / passthrough=yes comment="" disabled=no / queue type add name="PCQ-up" kind=pcq pcq-rate=350000 pcq-limit=50 / pcq-classifier=src-address pcq-total-limit=2000 add name="PCQ-down" kind=pcq pcq-rate=350000 pcq-limit=50 / pcq-classifier=dst-address pcq-total-limit=2000 / queue simple add name="PCQ"target-addresses=192.168.1.254/24 dst-address=0.0.0.0/0 / interface=all parent=none packet-marks=all-mark direction=both priority=1 /queue=PCQ-up/PCQ-down limit-at=0/0 max-limit=10000000/10000000 / total-queue=default-small disabled=yes / system script add name="PCQON" source=":if /(/[ /queue sim get /[/queue sim find / name=/"PCQ/"/] disable /]=true/) do={/queue sim enable PCQ}" /policy=ftp,reboot,read,write,policy,test,winbox,password add name="PCQOFF" source=":if /(/[ /queue sim get /[/queue sim find / name=/"PCQ/"/] disable /]=false/) do={/queue sim disable PCQ}" /policy=ftp,reboot,read,write,policy,test,winbox,password / tool traffic-monitor add name="PCQON" interface=ether3 traffic=received trigger=above / threshold=9800000 on-event=PCQON comment="" disabled=no add name="PCQOFF"interface=ether3 traffic=received trigger=below / threshold=5000000on-event=PCQOFF comment="" disabled=no----------上面是我修改好的完整脚本，是10m速度设置，下面是脚本注释，请仔细看下面说明，修改好你要限制的速度后在全部导入------:for szwm from 1 to 253 do={/queue simple add name=(TX . $szwm) target-addresses=(192.168.1. . $szwm) max-limit=500000/500000 interface=landisabled=no}这个是建立静态限速，也就是普通速度限制。

ROS最完美限速-根据带宽进行限速

ROS最完美限速-根据带宽进行限速在用脚本之前我们都是使用Simple Queue简单限速来进行客户机的限速，他的缺点是固定了每台客户机的最大上传下载速度，这样在人比较少，带宽占用不高的情况下，客人还是只能按高峰期的最大上传下载速度来上网，体现不了我们光纤极速上网的优势。

今天看了一天的资料看的我是头昏脑胀~~看什么都模糊了···最后看好这个脚本··最重要的不浪费我们的一点带宽以下脚本，是网通百兆电信10M的双线的带宽·带了256台客户机进行智能pcq限速。

现在暂时上传脚本不会的朋友等我到时候发个教程帖子给出详细设置··具体设置1、总下载带宽高于85M时，启动限速，每台机设置下载限速为4.5M。

2、总下载带宽低于40M时，取消限速。

3、总上传带宽高于60M时，启动限速，每台机设置上传限速为6M。

4、总上传带宽低于25M时，取消限速。

使用前，请先将原来的Simple Queue 中设定的限速指令删除。

同时，外网连接的名称要为wan/ip firewall mangle add chain=prerouting action=mark-packet new-packet-mark=all passthrough=no/queue type add name="PCQ_download" kind=pcq pcq-rate=4500000 pcq-classifier=dst-address/queue type add name="PCQ_upload" kind=pcq pcq-rate=6000000 pcq-classifier=src-address/queue tree add name="PCQdown" parent=global-in queue=PCQ_download packet-mark=all/queue tree add name="PCQup" parent=global-out queue=PCQ_upload packet-mark=all/ tool traffic-monitor add name="PCQdownon" interface=wan traffic=received trigger=above threshold=85000000 on-event=downon comment="" disabled=no/ tool traffic-monitor add name="PCQdownoff" interface=wan traffic=received trigger=below threshold=40000000 on-event=downoff comment="" disabled=no/ tool traffic-monitor add name="PCQupon" interface=wantraffic=transmitted trigger=above threshold=60000000 on-event=upon comment="" disabled=no/ tool traffic-monitor add name="PCQupoff" interface=wan traffic=transmitted trigger=below threshold=25000000 on-event=upoff comment="" disabled=no/ system scriptadd name="upon" source=":if $\[ /queue tree get \[/queue tree find name=\"PCQup\"\] disable \]=true $ do={/queue tree enable PCQup}" policy=password,read,reboot,write,policy,test/ system scriptadd name="upoff" source=":if $\[/queue tree get \[/queue tree find name=\"PCQup\"\] disable \]=false $ do={/queue tree disable PCQup}" policy=password,read,reboot,write,policy,test/ system scriptadd name="downon" source=":if $\[/queue tree get \[/queue tree find name=\"PCQdown\"\] disable \]=true $ do={/queue tree enable PCQdown}" policy=password,read,reboot,write,policy,test/ system scriptadd name="downoff" source=":if $\[/queue tree get \[/queue tree find name=\"PCQdown\"\] disable \]=false $ do={/queue tree disable PCQdown}" policy=password,read,reboot,write,policy,test其中的最大带宽触发数量，每台机触发后限制的带宽；以及最小带宽触发数量，这些需要根据实际运用中不断调整，才能达到最佳的效果。

1个简单的ping函数 -回复

1个简单的ping函数-回复如何创建一个简单的ping函数。

Ping是一种常用的网络工具，它用于测试主机之间的连接性以及计算机网络的性能。

在本文中，我们将讨论如何创建一个简单的ping函数，以便在自己的代码中使用它。

首先，我们需要了解ping命令的工作原理。

Ping命令发送一条ICMP （Internet控制报文协议）回显请求消息给特定的目标主机，并等待目标主机回复。

通过计算发送和接收之间的时间差，我们可以确定网络延迟。

在编写我们的ping函数之前，我们需要导入需要的库。

在Python中，我们可以使用socket库来进行网络编程操作。

让我们将其导入到我们的代码中：pythonimport socket接下来，我们可以定义我们的ping函数。

在这个函数中，我们将使用socket库来创建一个新的套接字对象，并发送ICMP请求消息给目标主机。

然后，我们等待目标主机的回复，并返回网络延迟。

pythondef ping(host):try:# 创建一个套接字对象s = socket.socket(socket.AF_INET, socket.SOCK_RAW, socket.getprotobyname("icmp"))# 设置套接字的超时时间s.settimeout(1)# 发送ICMP请求消息给目标主机s.sendto(b"", (host, 1))# 记录发送消息的时间戳start_time = time.time()# 等待接收目标主机的回复data, address = s.recvfrom(1024)# 计算网络延迟end_time = time.time()delay = end_time - start_time# 打印网络延迟print(f"Ping {host} delay is {delay} seconds.")# 关闭套接字s.close()# 返回网络延迟return delayexcept socket.error as e:# 如果发生异常，则打印错误消息print(f"Error: {e}")现在我们可以调用ping函数并测试它是否正常工作。

ros小包优化解决大型游戏卡问题(测试成功)

ros小包优化解决大型游戏卡问题(测试成功）/ ip firewall mangleadd chain=forward p2p=all-p2p action=mark-connection \new-connection-mark=p2p_conn passthrough=yes comment="" disabled=noadd chain=forward connection-mark=p2p_conn action=mark-packet \ new-packet-mark=p2p passthrough=yes comment="" disabled=noadd chain=forward connection-mark=!p2p_conn action=mark-packet \ new-packet-mark=general passthrough=yes comment="" disabled=noadd chain=forward packet-size=32-512 action=mark-packet new-packet-mark=all \ passthrough=yes comment="" disabled=noadd chain=forward packet-size=512-1200 action=mark-packet new-packet-mark=big \ passthrough=yes comment="" disabled=noadd chain=forward connection-mark=p2p_conn action=mark-packet \ new-packet-mark=p2p passthrough=yes comment="" disabled=noadd chain=forward p2p=all-p2p action=mark-connection \new-connection-mark=p2p_conn passthrough=yes comment="" disabled=noadd chain=forward connection-mark=!p2p_conn action=mark-packet \ new-packet-mark=general passthrough=yes comment="" disabled=noadd chain=forward packet-size=32-512 action=mark-packet new-packet-mark=all \ passthrough=yes comment="" disabled=noadd chain=forward packet-size=512-1200 action=mark-packet new-packet-mark=big \ passthrough=yes comment="" disabled=noadd chain=forward p2p=all-p2p action=mark-connection \new-connection-mark=p2p_conn passthrough=yes comment="" disabled=noadd chain=forward connection-mark=p2p_conn action=mark-packet \ new-packet-mark=p2p passthrough=yes comment="" disabled=noadd chain=forward connection-mark=!p2p_conn action=mark-packet \ new-packet-mark=general passthrough=yes comment="" disabled=noadd chain=forward packet-size=32-512 action=mark-packet new-packet-mark=all \ passthrough=yes comment="" disabled=noadd chain=forward packet-size=512-1200 action=mark-packet new-packet-mark=big \ passthrough=yes comment="" disabled=noadd chain=forward p2p=all-p2p action=mark-connection \new-connection-mark=p2p_conn passthrough=yes comment="" disabled=noadd chain=forward connection-mark=p2p_conn action=mark-packet \ new-packet-mark=p2p passthrough=yes comment="" disabled=noadd chain=forward connection-mark=!p2p_conn action=mark-packet \ new-packet-mark=general passthrough=yes comment="" disabled=noadd chain=forward packet-size=32-512 action=mark-packet new-packet-mark=all \ passthrough=yes comment="" disabled=noadd chain=forward packet-size=512-1200 action=mark-packet new-packet-mark=big \ passthrough=yes comment="" disabled=noadd chain=forward p2p=all-p2p action=mark-connection \new-connection-mark=p2p_conn passthrough=yes comment="" disabled=noadd chain=forward connection-mark=p2p_conn action=mark-packet \ new-packet-mark=p2p passthrough=yes comment="" disabled=noadd chain=forward connection-mark=!p2p_conn action=mark-packet \ new-packet-mark=general passthrough=yes comment="" disabled=noadd chain=forward packet-size=32-512 action=mark-packet new-packet-mark=all \ passthrough=yes comment="" disabled=noadd chain=forward packet-size=512-1200 action=mark-packet new-packet-mark=big \ passthrough=yes comment="" disabled=noadd chain=forward p2p=all-p2p action=mark-connection \new-connection-mark=p2p_conn passthrough=yes comment="" disabled=noadd chain=forward connection-mark=p2p_conn action=mark-packet \ new-packet-mark=p2p passthrough=yes comment="" disabled=noadd chain=forward connection-mark=!p2p_conn action=mark-packet \ new-packet-mark=general passthrough=yes comment="" disabled=noadd chain=forward packet-size=32-512 action=mark-packet new-packet-mark=all \ passthrough=yes comment="" disabled=noadd chain=forward packet-size=512-1200 action=mark-packet new-packet-mark=big \ passthrough=yes comment="" disabled=noadd chain=forward p2p=all-p2p action=mark-connection \new-connection-mark=p2p_conn passthrough=yes comment="" disabled=noadd chain=forward connection-mark=p2p_conn action=mark-packet \ new-packet-mark=p2p passthrough=yes comment="" disabled=noadd chain=forward connection-mark=!p2p_conn action=mark-packet \ new-packet-mark=general passthrough=yes comment="" disabled=noadd chain=forward packet-size=32-512 action=mark-packet new-packet-mark=all \ passthrough=yes comment="" disabled=noadd chain=forward packet-size=512-1200 action=mark-packet new-packet-mark=big \ passthrough=yes comment="" disabled=noadd chain=forward p2p=all-p2p action=mark-connection \new-connection-mark=p2p_conn passthrough=yes comment="" disabled=noadd chain=forward connection-mark=p2p_conn action=mark-packet \ new-packet-mark=p2p passthrough=yes comment="" disabled=noadd chain=forward connection-mark=!p2p_conn action=mark-packet \ new-packet-mark=general passthrough=yes comment="" disabled=noadd chain=forward packet-size=32-512 action=mark-packet new-packet-mark=all \ passthrough=yes comment="" disabled=noadd chain=forward packet-size=512-1200 action=mark-packet new-packet-mark=big \ passthrough=yes comment="" disabled=no。

ROS通过劫持ping实现穿越火线游戏0延迟

ROS通过劫持ping实现穿越火线游戏0延迟很多人在网吧玩《穿越火线》这类射击网游的时候，都会看到自己的ping（延迟）为0，都以为自己所在的网吧有多好多好.... 其实非也.. 只要在路由器写个命令即可实现。

123/ip firewall nat add action=redirect chain=dstnat comment="ping\BD\D9\B3\D6" disabled=no \ protocol=icmpROS 3.30测试通过。

w w w .b e a r p c .n e t下面是优化ping 值：1 2 3 4 5 6 7 8 9 10 11 # 优化CF 的PING 值/ip firewall address-listadd address=121.11.152.87 comment="cf icmp" disabled=no list=games add address=58.51.144.15 comment="cf icmp" disabled=no list=games add address=125.64.150.74 comment="cf icmp" disabled=no list=games add address=218.60.37.244 comment="cf icmp" disabled=no list=games add address=119.147.102.198 comment="cf icmp" disabled=no list=games add address=113.12.84.22 comment="cf icmp" disabled=no list=games add address=58.51.144.15 comment="cf icmp" disabled=no list=games add address=125.64.150.74 comment="cf icmp" disabled=no list=gamesw w w .b e a r p c .n et12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 add address=60.210.18.158 comment="cf icmp" disabled=no list=games add address=220.165.14.147 comment="cf icmp" disabled=no list=games add address=122.139.57.111 comment="cf icmp" disabled=no list=games add address=124.115.22.24 comment="cf icmp" disabled=no list=games add address=221.204.242.180 comment="cf icmp" disabled=no list=games add address=123.131.165.28 comment="cf icmp" disabled=no list=games add address=60.210.18.222 comment="cf icmp" disabled=no list=games add address=60.210.18.157 comment="cf icmp" disabled=no list=games add address=60.210.18.153 comment="cf icmp" disabled=no list=games add address=61.157.124.182 comment="cf icmp" disabled=no list=games add address=218.6.16.202 comment="cf icmp" disabled=no list=games add address=202.102.254.228 comment="cf icmp" disabled=no list=games add address=221.204.234.211 comment="cf icmp" disabled=no list=games add address=21.233.60.44 comment="cf icmp" disabled=no list=games add address=59.53.93.140 comment="cf icmp" disabled=no list=games add address=218.8.241.15 comment="cf icmp" disabled=no list=games add address=61.174.60.61 comment="cf icmp" disabled=no list=games add address=60.173.9.138 comment="cf icmp" disabled=no list=gamesww w .b e a r p c .n e t。