工厂常用英语词汇一览表
工厂常用英语
制造业常用英语词汇总经理办公室General manager’s office模具部Tooling department项目部Project department品质部Quality department计划部 Plan department制造部Manufacture departmentKeypad产品部Keypad departmentIMD 产品部 IMD department五金部 Metal stamping department设计科 Design section冲压车间 Stamping workshop电镀车间 Plating workshop物控科 Production material control section 计划科 Plan section仓务科 Warehouse section商务科 Business section品质规划科 quality plan sectionIQC科 IQC sectionIPQC科 IPQC sectionOQC科 OQC section检测中心 measurement center项目规划科 Project plan section项目XX科 Project section XX试模科 Mold test section成本科 Cost section设备科 Facility section采购科 Purchase section综合办 General affairs office编程科 Programming section模具工程科 Tooling engineering section模具装配车间Mold assembly workshop文控中心 Document control center (DCC)注塑车间Injection workshop喷涂车间 Spray painting workshop装配车间Assembly workshop总经理General manager (GM)经理managerXX部门经理Manager of XX department原料库 Raw material warehouse半成品库 Semi-finished product warehouse 成品库 Finished product warehouse科长 section chief主任 chief部门主管 department head主管, 线长supervisor组长Foreman, forelady秘书secretary文员clerk操作员operator助理assistant职员staff二、产品超声波焊接ultrasonic welding塑胶件 Plastic parts塑材 Raw parts喷涂件 Painted parts装配件 Assembly parts零件 Component原料 Raw material油漆 Paint稀释剂 Thinner油墨 Ink物料编号part number三、模具注塑模具injection mold冲压模具Stamping tool模架mold base定模座板Fixed clamp plate A板A plateB板B plate支承板 support plate方铁 spacer plate回位销 Return pin导柱 Guide pin动模座板Moving clamp plate 顶针ejector pin单腔模具single cavity mold 多腔模具multi-cavity mold 浇口gate合模力clamping force锁模力locking force开裂crack循环时间cycle time老化aging螺杆screw镶件 Insert主流道 sprue分流道runner浇口gate直浇口 direct gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate浇口套sprue bush流道板runner plate排气槽vent分型线（面）parting line定模Fixed mold动模movable mold型腔cavity凹模cavity plate，凸模core plate斜销angle pin滑块slide拉料杆sprue puller定位环locating ring脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mold 熔合纹weld line三板式模具three plate mold 脱模ejection脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure保压时间holding time闭模时间closing time电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine平面磨床Surface grinding machine万能摇臂钻床Universal radial movable driller 立式钻床Vertical driller倒角chamfer键Key键槽keyway间距pitch快速成型模Rapid prototype tool （RPT）四、品管SPC statistic process control品质保证Quality Assurance(QA)品质控制Quality control(QC)来料检验IQC Incoming quality control巡检IPQC In-process quality control校对calibration环境试验Environmental test光泽gloss拉伸强度tensile strength盐雾实验salt spray test翘曲warp比重specific gravity疲劳fatigue撕裂强度tear strength缩痕sink mark耐久性durability抽样sampling样品数量sample sizeAQL Acceptable Quality level批量lot size抽样计划sampling plan抗张强度 Tensile Strength抗折强度 Flexural Strength硬度 Rigidity色差 Color Difference涂镀层厚度 Coating Thickness导电性能 Electric Conductivity粘度 viscosity附着力 adhesion耐磨 Abrasion resistance尺寸 Dimension(喷涂)外观问题 Cosmetic issue不合格品 Non-conforming product限度样板 Limit sample五、生产注塑机injection machine冲床Punch machine嵌件注塑 Insert molding双色注塑 Double injection molding薄壁注塑 Thin wall molding膜内注塑 IMD molding ( In-mold decoration）移印 Tampo printing丝印 Silk screen printing热熔 Heat staking超声熔接 Ultrasonic welding (USW）尼龙nylon黄铜 brass青铜 bronze紫(纯)铜 copper料斗hopper麻点pit配料compounding涂层coating飞边flash缺料 Short mold烧焦 Burn mark缩水 Sink mark气泡 Bubbles破裂 Crack熔合线 Welding line流痕 Flow mark银条 Silver streak黑条 Black streak表面光泽不良 Lusterless表面剥离 Pelling翘曲变形 Deformation脏圬 Stain mark油污 Oil mark蓝黑点 Blue-black mark顶白 Pin mark拉伤 Scratch限度样品 Limit sample最佳样品 Golden sample预热preheating再生料recycle material机械手 Robot机器人 Servo robot试生产 Trial run; Pilot run (PR)量产 mass production切料头 Degate产能 Capacity能力 Capability参数 Parameter二次加工 Secondary process六．物控保质期shelf lifeABC分类法ABC Classification装配Assembly平均库存Average Inventory批号Batch Number批量生产Mass Production提货单Bill of Lading物料清单Bill of Material采购员Buyer检查点Check Point有效日期Date Available修改日期Date Changed结束日期Date Closed截止日期Date Due生产日期Date in Produced库存调整日期Date Inventory Adjust 作废日期D ate Obsolete收到日期Date Received交付日期Date Released需求日期Date Required需求管理Demand Management需求Demand工程变更生效日期Engineering Change Effect Date呆滞材料分析Excess Material Analysis完全跟踪Full Pegging在制品库存In Process Inventory投入/产出控制Input/ Output Control检验标识Inspection ID库存周转率Inventory Carry Rate准时制生产Just-in-time (JIT)看板Kanban人工工时Labor Hour最后运输日期Last Shipment Date提前期Lead Time负荷Loading仓位代码Location Code仓位状况Location Status批量标识Lot ID批量编号Lot Number批量Lot Size机器能力Machine Capacity机器加载Machine Loading制造周期时间Manufacturing Cycle Time制造资源计划Manufacturing Resource Planning (MRP II)物料成本Material Cost物料发送和接收Material Issues and Receipts物料需求计划Material Requirements Planning现有库存量On-hand Balance订单输入Order Entry零件批次Part Lot零件编号Part Number (P/N)零件Part领料单Picking List领料/提货Picking产品控制Product Control产品线Production Line采购订单跟踪Purchase Order Tracking需求量Quantity Demand毛需求量Quantity Gross安全库存量Safety Stock在制品Work in Process零库存Zero Inventories七．QS-9000中的术语APQP Advanced Product Quality Planning and Control Plan，产品质量先期策划和控制计划PPAP Production Part Approval Process,生产件批准程序FMEA Potential Failure Mode and Effects Analysis,潜在失效模式及后果分析MSA Measure System Analysis,测量系统分析SPC Statistical Process Control,统计过程控制审核 Audit能力 Capability能力指数 Capability Indices控制计划 Control Plans纠正措施 Corrective Action文件 Documentation作业指导书 Standard operation procedure (SOP); Work instruction不合格品 Nonconformance不合格 Nonconformity每百万零件不合格数 Defective Parts Per Million, DPPM预防措施 Preventive Action程序Procedures过程流程图 Process Flow Diagram, Process Flow Chart质量手册Quality Manual质量计划 Quality Plan质量策划 Quality Planning质量记录Quality Records原始数据Raw Data反应计划Reaction Plan返修Repair返工Rework现场Site分承包方Subcontractors产品product质量quality质量要求quality requirement顾客满意customer satisfaction质量管理体系quality management system质量方针quality policy质量目标quality objective质量管理quality management质量控制quality control质量保证quality assurance组织organization顾客customer供方supplier过程process服务service设计与开发design and development：特性characteristic可追溯性trace ability合格conformity缺陷defect纠正correction让步concession放行release报废scrap规范specification检验inspection试验test验证verification评审review测量measurement普通原因Common Cause均值Mean极差Range稳定性Stability计量型数据Variables Data变差Variation重复性Repeatability再现性Reproducibility稳定性Stability分辨率Resolution过程更改Process change质量功能展开QFD外观项目Appearance Item初始过程能力Preliminary Process Capability 材料清单Bill of Material设计确认Design Validation设计验证Design Verification八．常用缩略词语OEM Original Equipment Manufacturer ANOVA 方差分析法 Analysis of VarianceDFMEA 设计失效模式及后果分析 Design Failure Mode and Effects Analysis DOE 试验设计 Design of ExperimentGR&R 量具的重复性和再现性Gage Repeatability and Reproducibility PFMEA 过程失效模式及后果分析Process Failure Mode and Effect Analysis QSR 质量体系要求Quality System RequirementQFD 质量功能展开 Quality Function DeploymentBOM 物料清单 Bill of MaterialCpk 稳定过程的能力指数 Capability for stable processLCL 下控制限 Lower Control LimitUCL 上控制限 Upper Control LimitLSL 工程规范下限 Lower Specification LimitX(—)--R图均值一极差图 Average-Range Chart防错（POKA-YOKE）Mistake ProofingETA 预计到达 Estimate to be arrivePO 定单 Purchase orderM/C 机器 machineRFQ 报价需求 Request for quotationMFI 熔融流动指数 Melt flow indexFAI 全尺寸检测报告 First article inspectionCOC 材质证明 Certificate of complianceALT 加速老化试验 Accelerated life testCRR 承认书 Component review reportOT 加班 Over timeCAP 矫正计划 Corrective action planR&D 研发 Research and DevelopmentASAP 尽快 As soon as possibleECN工程更改通知Engineering change noticeDCN 设计更改通知 Design change noticeOTD 准时交货 On time delivery九．通用词语确保 ensure构想 construct会签 con-sign功能 Function机构 organization外观 appearance适用 apply to作业流程 Operation flow附件 attachment商务人员 business personnel汇总 summarize指定相关人员 designated personnel新产品开发说明会 new product development explanation meeting拟定 Prepare委托 entrust认证 qualify电子档 Soft copy3D文件 3D database移转 Transfer执行 ConductXXX申请单 XXX Application form客户要求 Customer requirement启动 Kick off评估 Evaluation作业员 Operator批准, 承认 Approval合同评审 Contract review可靠性 Reliability相关的 Relevant程序 Procedure制程 Process流程图 Flow chart产品 Product生产 Production资材 Logistics责任 Responsibility跟进 Follow-up交付 Delivery汇总 Summarize外协加工 subcontract指定相关人员 designated personnel编号 number附件 attachment产品名称 Description周期循环时间 Cycle time模具号 Mold No,数量 quantity ( Qt’y )备注 remarkSAP号 SAP No.客户 Customer表单 Form初步的 Preliminary版本 Version根本原因 Root cause（喷漆）夹具 Fixture（设备）小夹具 Jig设备 Equipment设施 Facility送，提交（样品）Submit责任部门,责任人 Responsible by（大的）目标 Objective(小的，具体的)目标 Target格式 Format上岗证 Qualification card需求 Requirement现场 On site查检表 Checklist试产 pilot增值税 VAT---value-added tax品质专业英语大全零件材料类的专有名词CPU: central processing unit(中央处理器)IC: Integrated circuit(集成电路)Memory IC: Memory Integrated circuit（记忆集成电路）RAM: Random Access Memory（随机存取存储器）DRAM: Dynamic Random Access Memory（动态随机存取存储器）SRAM: Staic Random Access Memory（静态随机存储器）ROM: Read-only Memory（只读存储器）EPROM:Electrical Programmable Read-only Memory（电可抹只读存诸器）EEPROM: Electrical Erasbale Programmable Read-only Memory（电可抹可编程只读存储器）CMOS: Complementary Metal-Oxide-Semiconductor（互补金属氧化物半导体）BIOS: Basic Input Output System（基本输入输出系统）Transistor：电晶体LED:发光二极体Resistor：电阻Variator：可变电阻Capacitor:电容Capacitor array：排容Diode：二极体Transistor：三极体Transformer：变压器（ADP）Oscillator：频率振荡器（0sc）Crystal：石英振荡器XTAL/OSC:振荡产生器（X）Relay：延时器Sensor：感应器Bead core：磁珠Filter:滤波器Flat Cable：排线Inductor：电感Buzzer：蜂鸣器Socket：插座Slot：插槽Fuse：熔断器Current：电流表Solder iron：电烙铁Magnifying glass：放大镜Caliper：游标卡尺Driver：螺丝起子Oven：烤箱TFT:液晶显示器Oscilloscope：示波器Connector：连接器PCB:printed circuit board（印刷电路板）PCBA: printed circuit board assembly（电路板成品）PP:并行接口HDD:硬盘FDD:软盘PSU:power supply unit（电源供应器）SPEC:规格Attach:附件Case: 机箱，盖子Cover：上盖Base：下盖Bazel：面板（panel）Bracket：支架，铁片Lable：贴纸Guide：手册Manual：手册，指南Card：网卡Switch：交换机Hub：集线器Router：路由器Sample：样品Gap：间隙Sponge：海绵Pallet：栈板Foam：保利龙Fiber：光纤Disk：磁盘片PROG:程序Barcode：条码System：系统System Barcode：系统条码M/B:mother board：主板CD-ROM:光驱FAN:风扇Cable：线材Audio：音效K/B:Keyboard（键盘）Mouse：鼠标Riser card：转接卡Card reader：读卡器Screw：螺丝Thermal pad：散热垫Heat sink：散热片Rubber：橡胶垫Rubber foot：脚垫Bag：袋子Washer：垫圈Sleeve：袖套Config：机构Label hi-pot：高压标签Firmware label：烧录标签Metal cover：金属盖子Plastic cover：塑胶盖子Tape for packing：包装带Bar code：条码Tray：托盘Collecto：集线夹Holder：固定器,L铁Connecter：连接器IDE:集成电路设备，智能磁盘设备SCSI:小型计算机系统接口Gasket：导电泡棉AGP:加速图形接口PCI:周边组件扩展接口LAN:局域网USB:通用串形总线架构Slim：小型化COM:串型通讯端口LPT:打印口，并行口Power cord：电源线I/O:输入，输出Speaker：扬声器EPE:泡棉Carton：纸箱Button：按键，按钮Foot stand：脚架部门名称的专有名词QS:Quality system品质系统CS:Coutomer Sevice 客户服务QC:Quality control品质管理IQC:Incoming quality control 进料检验LQC:Line Quality Control 生产线品质控制IPQC:In process quality control 制程检验FQC:Final quality control 最终检验OQC:Outgoing quality control 出货检验QA:Quality assurance 品质保证 SQA:Source(supplier) Quality Assurance 供应商品质保证(VQA) CQA：Customer Quality Assurance客户质量保证PQA rocess Quality Assurance 制程品质保证QE:Quality engineer 品质工程CE:component engineering零件工程EE:equipment engineering设备工程ME:manufacturing engineering制造工程TE:testing engineering测试工程PPE roduct Engineer 产品工程IE:Industrial engineer 工业工程ADM: Administration Department行政部RMA:客户退回维修CSDI:检修PC:producing control生管MC:mater control物管GAD: General Affairs Dept总务部A/D: Accountant /Finance Dept会计LAB: Laboratory实验室DOE:实验设计HR:人资PMC:企划RD:研发W/H:仓库SI:客验PD: Product Department生产部PA:采购(PUR: Purchaing Dept)SMT:Surface mount technology 表面粘着技术MFG:Manufacturing 制造MIS:Management information system 资迅管理系统DCC:document control center 文件管制中心厂内作业中的专有名词QT:Quality target品质目标QP:Quality policy目标方针QI:Quality improvement品质改善CRITICAL DEFECT:严重缺点（CR）MAJOR DEFECT:主要缺点（MA）MINOR DEFECT:次要缺点（MI）MAX:Maximum最大值MIN:Minimum最小值DIA iameter直径DIM imension尺寸LCL:Lower control limit管制下限UCL:Upper control limit管制上限EMI:电磁干扰ESD:静电防护EPA:静电保护区域ECN:工程变更ECO:Engineering change order工程改动要求（客户）ECR:工程变更需求单CPI:Continuous Process Improvement 连续工序改善Compatibility：兼容性Marking：标记DWG rawing图面Standardization：标准化Consensus：一致Code：代码ZD:Zero defect零缺点Tolerance：公差Subject matter：主要事项Auditor：审核员BOM:Bill of material物料清单Rework：重工ID：identification识别,鉴别,证明PILOT RUN: (试投产)FAI:首件检查FPIR：First Piece Inspection Report首件检查报告FAA:首件确认SPC：统计制程管制CP: capability index（准确度）CPK: capability index of process(制程能力)PMP:制程管理计划（生产管制计划）MPI:制程分析DAS efects Analysis System 缺陷分析系统PPB：十亿分之一Flux：助焊剂P/N:料号L/N：Lot Number批号Version：版本Quantity：数量Valid date：有效日期MIL-STD：Military-Standard军用标准ICT: In Circuit Test (线路测试)ATE：Automatic Test Equipment自动测试设备MO: Manafacture Order生产单T/U: Touch Up (锡面修补)I/N:手插件P/T:初测F/T: Function Test (功能测试-终测)AS 组立P/K:包装TQM:Total quality control全面品质管理MDA:manufacturing defect analysis制程不良分析(ICT) RUN-IN:老化实验HI-pot：高压测试FMI：Frequency Modulation Inspect高频测试DPPM: Defect Part Per Million(不良率的一种表达方式：百万分之一) 1000PPM即为0.1% Corrective Action: (CAR改善对策)ACC：允收REJ:拒收S/S：Sample size抽样检验样本大小SI-SIV：Special I-Special IV特殊抽样水平等级CON：Concession / Waive特采ISO:国际标准化组织ISA：Industry Standard Architecture工业标准体制结构OBA:开箱稽核FIFO:先进先出PDCA:管理循环Plan do check action计划，执行，检查，总结WIP:在制品（半成品）S/O: Sales Order (业务订单)P/O: Purchase Order (采购订单)P/R: Purchase Request (请购单)AQL:acceptable quality level允收品质水准LQL;Limiting quality level最低品质水准QVL:qualified vendor list合格供应商名册AVL ：认可的供货商清单(Approved Vendor List)QCD: Quality cost delivery（品质，交期，成本）MPM:Manufacturing project management制造专案管理KPI:Key performance indicate重要绩效指标MVT:Manufacturing Verification Test制造验证试产Q/R/S：Quality/Reliability/Service质量/可靠度/服务STL:ship to line（料到上线）NTF:No trouble found误判CIP:capacity improvement plan（产能改善计划）MRB:material review board（物料审核小组）MRB:Material reject bill退货单JIT:just in time（即时管理）5S:seiri seiton seiso seiketsu shitsuke（整理，整顿，清扫，清洁，修养）SOP:standard operation process（标准作业程序）SIP:Specification inspection process制程检验规格TOP: Test Operation Process (测试作业流程)WI: working instruction（作业指导书）SMD:surface mounting device（表面粘着原件）FAR:failure aualysis report故障分析报告CAR:Corrective action report改善报告BPR：企业流程再造 (Business Process Reengineering)ISAR ：首批样品认可(Initial Sample Approval Request)-JIT：实时管理 (Just In Time)QCC ：品管圈 (Quality Control Circle)Engineering Department (工程部)TQEM: Total Quality Environment Management(全面品质环境管理)PD: Production Department (制造)LOG: Logistics (后勤支持)Shipping: (进出口)AOQ：Average Output Quality平均出货质量AOQL：Average Output Quality Level平均出货质量水平FMEA：failure model effectiveness analysis失效模式分析CRB: Change Review Board (工程变更会议)CSA：Customer Simulate Analysis客户模拟分析SQMS：Supplier Quality Management System供应商品质管理系统QIT: Quality Improvement Team 品质改善小组QIP：Quality Improvement Plan品质改善计划CIP：Continual Improvement Plan持续改善计划M.Q.F.S: Material Quality Feedback Sheet (来料品质回馈单) SCAR: Supplier Corrective Action Report (供货商改善对策报告)8D Sheet: 8 Disciplines sheet ( 8D单)PDCA：PDCA (Plan-Do-Check-Action) (管理循环)MPQ: Material Packing Quantity (物料最小包装量)DSCN: Delivery Schedule Change Notice (交期变更通知) QAPS: Quality Assurance Process Sheet (品质工程表)DRP ：运销资源计划 (Distribution Resource Planning)DSS：决策支持系统 (Decision Support System)EC ：电子商务 (Electronic Commerce)EDI ：电子资料交换 (Electronic Data Interchange)EIS ：主管决策系统 (Excutive Information System)ＥＲＰ：企业资源规划 (Enterprise Resource Planning)FMS ：弹性制造系统 (Flexible Manufacture System)KM ：知识管理 (Knowledge Management)4L ：逐批订购法 (Lot-for-Lot)LTC ：最小总成本法 (Least Total Cost)LUC ：最小单位成本 (Least Unit Cost)MES ：制造执行系统 (Manufacturing Execution System)MPS ：主生产排程 (Master Production Schedule)MRP ：物料需求规划 (Material Requirement Planning)MRPⅡ：制造资源计划 (Manufacturing Resource Planning)OEM ：委托代工 (Original Equipment Manufacture)ODM ：委托设计与制造 (Original Design & Manufacture) OLAP：线上分析处理 (On-Line Analytical Processing)OLTP：线上交易处理 (On-Line Transaction Processing)OPT ：最佳生产技术 (Optimized Production Technology) PDCA：PDCA管理循环 (Plan-Do-Check-Action)PDM：产品数据管理系统 (Product Data Management))RCCP：粗略产能规划 (Rough Cut Capacity Planning)SCM ：供应链管理 (Supply Chain Management)SFC ：现场控制 (Shop Floor Control)TOC：限制理论 (Theory of Constraints)TQC ：全面品质管制 (Total Quality Control)FYI/R:for your information/reference仅供参考ASAP:尽快S/T:Standard time标准时间TPM:total production maintenance：全面生产保养ESD Wrist strap：静电环IT:information technology信息技术，资讯科学CEO：Chief Executive Officer执行总裁COO：Chief Operaring Officer首席业务总裁SWOT：Strength,Weakness,Opportunity,Threat优势﹐弱点﹐机会﹐威胁Competence：专业能力Communication：有效沟通Cooperation：统御融合Vibration Testing：振动测试IDP：Individual Development Plan个人发展计划MRP：Material Requirement Planning物料需求计划MAT'S：Material材料LRR：Lot Rejeet Rate批退率ATIN：Attention知会3C：Computer ,Communication , Consumer electronic消费性电子5W1H：When , Where , Who , What , Why , Ho5M: Man , Machine , Material , Method , Measurement人,机器,材料,方法,测量4MIE: Man,Material,Machine,Method,Environment人力,物力,财务,技术,时间(资源)7M1I: Manpower , Machine , Material , Method, Market , Management , Money , Information 人力，机器，材料，方法, 市场，管理，资金，资讯1 Accuracy 准确度2 Action 行动3 Activity 活动4 Analysis Covariance 协方差分析5 Analysis of Variance 方差分析6 Approved 承认7 Attribute 计数值8 Average 平均数9 Balance sheet 资产负债对照表10 Binomial 二项分配11 Brainstorming Techniques 脑力风暴法12 Cause and Effect Matrix 因果图(鱼骨图)13 CL:Center Line 中心线14 Check Sheets 检查表15 Complaint 投诉16 Conformity 合格（符合）17 Control 控制18 Control chart 控制(管制)图19 Correction 纠正20 Correlation Methods 相关分析法21 CPI: continuouse Process Improvement 连续工序改善22 Cross Tabulation Tables 交叉表23 CS: Customer Sevice 客（户）服（务）中心24 DSA: Defects Analysis System 缺陷分析系统25 Data 数据 Description:品名26 DCC: Document Control Center 文控中心27 Decision 决策、判定28 Defects per unit 单位缺点数29 Description 描述30 Device 装置31 Do 执行32 DOE: Design of Experiments 实验设计33 Element 元素34 Engineering recbnology 工程技35 Environmental 环境36 Equipment 设备37 Estimated accumulative frequency 计算估计累计数38 E Equipment Variation 设备变异39 External Failure 外部失效,外部缺陷40 FA: Failure Analysis 失效分析41 Fact control 事实管理42 Fatigue 疲劳43 FMEA: Failure Mode and Effect Analysis失效模式与效果分析44 FP First-Pass Yield （第一次通过）合格率45 FQA: Final Quality Assurance 最终品质保证46 FQC: Final Quality control 最终品质控制47 Gauge system 测量系统48 Grade 等级49 Histogram 直方图50 Improvement 改善51 Initial review 先期审查52 Inspection 检验53 Internal Failure 内部失效、内部缺陷54 IPQC: In Process Quality Control 制程品质控制55 IQC: Incomming Quality Control 来料品质控制56 IS International Organization for Standardization 国际标准化组织57 LCL: Lower Control limit 管制下限58 LQC: Line Quality Control 生产线品质控制59 LSL: Lower Size Limit 规格下限60 Machine 机械61 Manage 管理62 Materials 物料63 Measurement 测量64 Median 中位数65 MSA: Measurement System Analysis 测量系统分析66 Occurrence 发生率67 Operation Instruction 作业指导书68 Organization 组织69 Parto 柏拉图70 PPM arts per Million （百万分之）不良率71 Plan 计划72 Policy 方针73 Population 群体74 PQA: Process Quality Assurance 制程品质保证75 Practice 实务(践)76 Prevention 预防77 Probability 机率78 Probability density function 机率密度函数79 Procedure 流程80 Process 过程81 Process capability analysis 制程能力分析（图）82 Process control and Process capability制程管制与制程能力83 Product 产品84 Production 生产85 Projects 项目86 QA: Quality Assurance 品质保证87 QC: Quality Control 品质控制88 QE: Quality Engineering 品质工程89 QFD: Quality Function Desgin 品质机能展开(法)90 Quality 质量91 Quality manual 品质手册92 Quality policy 品质政策(质量方针)93 Random experiment 随机试验94 Random numbers 随机数95 R:Range 全距（极差）96 Reject 拒收97 Repair 返修98 Repeatusility 再现性99 Reproducibility 再生性100 Requirement 要求101 Responsibilities 职责102 Review 评审103 Reword 返工104 Rolled yield 直通率105 RPN: Risk Priority Number 风险系数106 Sample 抽样,样本107 Sample space 样本空间108 Sampling with replacement 放回抽样109 Sampling without replacement 不放回抽样110 Scatter diagram 散布图分析111 Scrap 报废112 Simple random sampling 简单随机取样113 Size 规格114 SL: Size Line 规格中心线115 Stratified random sampling 分层随机抽样116 SOP: Standard Operation Procedure 标准作业书117 SPC: Statistical Process Control 统计制程管制118 Specification 规范119 SQA: Source(Supplier) Quality Assurance 供货商品质保证120 Stage sampling 分段随机抽样121 Standard Deviation 标准差122 Sum of squares 平方和123 Taguchi-method 田口(试验)方法124 Theory 原理125 TQC: Total Quality Control 全面品质控制126 TQM: Total Quality Management 全面品质管理127 Traceablity 追溯128 Training 培训129 UCL: Upper Control Limit 管制（控制）上限130 USL: Upper Size Limit 规格上限131 Validation 确认132 Variable 计量值133 Verification 验证134 Version 版本135 VOC: Voice of Customer 客户需求136 VOE: Voice of Engineer 工程需求137 Inventory stock report:庫存清单报告138 Sales order report:出货报告质量人员名称类QC quality control 品质管理人员FQC final quality control 终点质量管理人员IPQC in process quality control 制程中的质量管理人员OQC output quality control 最终出货质量管理人员IQC incoming quality control 进料质量管理人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 质量工程人员质量保证类FAI first article inspection 新品首件检查FAA first article assurance 首件确认CP capability index 能力指数CPK capability process index 模具制程能力参数SSQA standardized supplier quality audit 合格供货商质量评估FMEA failure model effectiveness analysis 失效模式分析FQC运作类AQL Acceptable Quality Level 运作类允收质量水平S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的Q/R/S Quality/Reliability/Service 质量/可靠度/服务P/N Part Number 料号L/N Lot Number 批号AOD Accept On Deviation 特采UAI Use As It 特采FPIR First Piece Inspection Report 首件检查报告PPM Percent Per Million 百万分之一制程统计品管专类SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计质量管理GRR Gauge Reproductiveness & Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径N Number 样品数其它质量术语类QIT Quality Improvement Team 质量改善小组ZD Zero Defect 零缺点QI Quality Improvement 质量改善QP Quality Policy 目标方针TQM Total Quality Management 全面质量管理RMA Return Material Audit 退料认可7QCTools 7 Quality Control Tools 品管七大手法通用之件类ECN Engineering Change Notice 工程变更通知(供货商)ECO Engineering Change Order 工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Standard Inspection Procedure 制程检验标准程序SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类ES Engineering Standard 工程标准CGOO China General PCE龙华厂文件IWS International Workman Standard 工艺标准ISO International Standard Organization 国际标准化组织GS General Specification 一般规格部类PMC Production & Material Control 生产和物料控制PCC Product control center 生产管制中心PPC Production Plan Control 生产计划控制MC Material Control 物料控制DC Document Center 资料中心QE Quality Engineering 质量工程(部)QA Quality Assurance 质量保证(处)QC Quality Control 质量管理(课)PD Product Department 生产部LAB Laboratory 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部生产类PCs Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供货商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号OEM Original Equipment Manufacture 原设备制造PC Personal Computer 个人计算机CPU Central Processing Unit 中央处理器A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量I/O input/output 输入/输出NG Not Good 不行,不合格C=0 Critical=0 极严重不允许APP Approve 核准,认可,承认CHK Check 确认ASS'Y Assembly 装配,组装T/P True Position 真位度5WIH When, Where, Who, What, Why, How to6M Man, Machine, Material, Method, Measurement, Message4MTH Man, Material, Money, Method, Time, How 人力,物力,财务,技术,时间(资源) SQA Strategy Quality Assurance 策略质量保证DQA Design Quality Assurance 设计质量保证MQA Manufacture Quality Assurance 制造质量保证SSQA Sales and service Quality Assurance 销售及服务质量保证LRR Lot Reject Rate 批退率SPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Video DiskVCD Video Compact DiskLCD Liquid Crystal DisplayCAD Computer Aided DesignCAM Computer Aided ManufacturingCAE Computer Aided EngineeringPCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WDR Weekly Delivery Requirement 周出货要求PPM Percent Per Million 百万分之一TPM Total Production Maintenance 全面生产保养MRP Material Requirement Planning 物料需计划OS Operation System 操作系统TBA To Be Assured 待定,定缺D/C Drawing ChangeP/P Plans & ProcedureEMI Electrical-Music Industry 电子音乐工业Electrical Magnetic Interference 电子干扰RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material SizeLED lighting-emitting diode 发光二极管QBR Quarter Business RecordCIP Continuous improvement processFGI Forecasted Goal InventoryCNC Computerized numeral controllerB2C Business to customerB2B Business to businessAVL Approved vendor listPOP Procedure of packagingEOL End of lifeVDCS Vender defect correcting sheetPDCS Process defect correcting sheetGRN Goods receiving noteA/R Accounting receivableA/P Accounting payable专业词汇通用类president董事长operator作业员position职务general manager总经理special assistant 特助deputy manager |'depjuti| =vice manager副理deputy supervisor =vice supervisor副课长group leader组长line leader线长supervisor 课长responsible department负责单位Human Resources Department人力资源部Head count 人头数production department生产部门planning department企划部QC Section品管课stamping factory冲压厂painting factory烤漆厂molding factory成型厂administration/general affairs dept./总务部production unit生产单位meeting minutes会议记录distribution department分发单位subject主题conclusion结论decision items决议事项pre-fixed finishing date预定完成日Color management 颜色管理Visual management 目视管理production capacity生产力first count初盘first check初盘复棹second count 复盘second check复盘复核quantity of physical inventory second count 复盘点数量physical inventory盘点数量physical count quantity账面数量difference quantity差异量spare parts physical inventory list备品盘点清单cause analysis原因分析waste materials废料description品名specification 规格model机种work order工令。
车间常用英语单词
车间常用英语单词车间常用词汇表工具加工术语量具公差板手Spanner半精加工Semi Finishing百分表Dial test超差Overtolerance 锉刀File精加工Finishing螺纹环规Thread Ring Gauge上差Upper deviation 顶针Centre粗加工Roughing螺纹量规Thread Gauge下差Lower deviation 定位销Location pin车外圆Turning OD外径千分尺Outside Micrometer尺寸标注Dimension creation 防锈油Corrosion Preventive Oil镗内空Boring ID内径千分尺inside Micrometer尺寸公差Dimension tolerance 虎钳Vice车螺纹Thread turning游标卡尺Calliper（Vernier Calipers）基孔制Hole-basis-system of fits 压板Clamping Plate攻丝Tapping三坐标测量仪CMM基轴制Shaft-basis-system of fits 夹具Fixture铣削Milling高度尺High gauge基准Datum 研磨膏Lapping Paste磨削Grinding高度仪High gauge基准面Reference surface 内六角板手internal Hexagon spanner车削Turning塞规Plug Gauge基准线Reference line 切削液Coolant打磨Fitting投影仪Projector scope对称度Symmetry 圆锥销Taper Pin刀具半径补偿Tool Radius Offset内径量表Bore Guage垂直度Perpendicularity 卡爪Jaw主轴转速Spindle Speed深度尺Sliding Depth callipers同心度Concentricity 卡盘Chuck切削深度Cutting Depth环规Ring gauge同轴度Coaxis 固定螺钉Clamping Screw切削速度Cutting Speed空气量仪Air gauge圆度Roundness 螺丝刀screwdriver装夹Set Up粗糙度仪Rough machine平行度Parallelism 铁锤hammer 通孔Through hole大理石平台leveling block倾斜度Angularity 盲孔Blind hole校验calibration平面度Flatness顺铣climb milling Pin圆柱度Cylindricality逆铣up cut milling做膜投影Cast & project直线度Straightness 抛光Polish Surface compare位置度PositionVisual表面粗糙度surface finishChamfer gaugeThread gaugeRadius gaugeDial test & V-block刀具其他车刀Turning Tool回火Tempering中心钻Centre dirll调质处理Thermal Refining浅孔钻U Drill退火Annealing钻头Drill正火Normalizing钻夹头Bit Chuck阳极化Anodizing铣刀Milling Tool无损检验Nondestructive Testing 面铣刀Face Milling cutter热处理Heat Treatment铰刀Reamer射线探伤FPI槽刀solt milling cutter磁粉探伤MPI镗刀Boring bar镀镉Cadmium插铣刀Plunge milling cutter镀铬Chrome砂轮Grind wheel报废Scrap丝锥Tap让步接收Concession刀夹Cartridge返工Rework路卡route card铸件casting锻件forging序列号Server no卧式加工中心horizontal machine center立式加工中心vertical machine center行车travelling crane电源power supply集装箱container托盘salver铲车forklift幼儿园kindergarten小学elementary school。
工厂常用英语单词
工厂常用英语单词1-1 Substitution1-1代用料balance 結余Alternate current交流電bar code label 條碼標籤AC inletAC插座(電源插座)base 基極基礎acceptable可接受的basic 基本的action行動行為battery 電池active有效的現行的bead core 磁線圈active area有效面積biased 偏置active model有效機種block NO 半成品號additional附加的blooming 涂層開花address label地址標籤board 廠牌板子adhesive膠有粘性的BOM:bill of material 物料清單adhesive three bond 綠膠bonded 粘合的adhesive silicone矽膠board corrugated paper 天地紙板(棧板上面及Monitor 上:)adjustment判斷調整bottom 底部adjust調整bracket 托架括弧AI fixtureAI電氣設備bridge rectifier 橋式整流器AI: auto insertion自動插件部brightness 亮度aid援助brightness uniformity 亮度一致性air condition空運條件bulk rectifiers 矯正器air rubble bag氣泡墊bulky 大宗的笨大的altitude高度bumps ripples 波紋ALU(capacitor)鋁質(電解電容)burning room 燒機房加溫室amber琥珀色by block NO 按機種半品料號階排列ampere安培by model NO 按機種排列amplifier放大器analog模擬cable 線analysis分析cable ties 束線袋application應用cablet bracket 固定片apply應用申請CAI:computer AID issuring 電腦自動模擬發料approval審核承認cancel 取消approve同意贊成CAP:Capacity 電容arrange整理CAP ALU ELECTROLYTIC-400V 鋁質電解電容400以上assign指定,分配CAP ALU ELECTROLYTIC-OTHE 電解電容attachment 附件CAP FILM SPECIAL 薄膜電容audio音頻CAP MEF 金屬化聚乙脂膜電容器audio board音量板CAP MEM 小型化塑膠電容(MEF)audit檢核CAP MPP 金屬化聚丙烯膜電容automatic degaussing自動消磁CAP PEI 聚丙乙烯膜電容(無感式)available 準備好的通用的CAP PEM 聚丙乙烯膜電容(有感式)CAP PPM 聚丙烯電容器collector 集電電路CAP PPN 聚丙烯薄膜電容color/colour 顏色CAP PPS 串連式聚丙烯膜電容器color sticker 彩色貼紙CAP PS 聚丙乙烯膜電容器度射column 列CAP TAN 鉭電容commodity 屬性種類CAP VARIABLE 可變電容common base 共基電路CAP Y Y電容common choke 環形濾波線圈CAR:corrective and action report 校正與預防措施報告common choke 普通扼流圈capability 性能能力company 公司capacitor 電容容量compare 比較對照capacity 能量電容compatibility 兼容性capatine/with 可連接/插上complain 抱怨capacity 電容component 零件calendar 日程表computer 計算機carton 紙箱condition 條件carton box 紙箱confirm 確定cause 原因connector 連接器CC resistor 碳合成電阻consumption 消耗CD(capacitor)陶瓷電容continue 繼續CEM resistor 水泥電阻control chart 控制圖center 中心contract 合同carbon film resistor 碳膜電阻contrast 對比度CR resistor 碳膜電阻(色碼電阻)control BD 控制板change your password 改變密碼core magnetic 磁鐵磁芯characteristics 特性corrective 改善的charge 使承擔使負擔cost 成本chart 流程圖coustomer 顧客客戶chassis 機座critical 極限限制check 檢查CRT 映像管check point 檢查點CRT board CRT電路板choke 扼流圈CRT GND WIRE CRT接地線chromaticity 色度CRT screw CRT螺絲circuit 電路CRT socket CRT插座circuit board 電路板CRT test CRT測試CKD-ID 位置CRT:cathode ray tube 陰極射線管cleaner naphtha 清潔劑current 電流clip 夾子cushion 墊片code 代碼CUT-IN code 切入代碼coil 線圈coil rotation 傾斜線圈daily 每日的coil choke 扼流線圈data display area dimension and posi 數據顯示區域coil degaussing 消磁線圈date 日期coil linear 枕型調整線圈date code label 日期標籤coil peaking 蜂化線圈direct current 直流電conductivity 電導率DC input impedance 直流輸入阻抗本冊英語單詞是工廠常用之基本詞匯.DAB C 第 1 頁共 13 頁DDC:display data channel 顯示器數據通道electrostatic 靜電defect 不良electrostatic discharge 放靜電deffused ambient 散射環境EMI:(Electronic&Magnetic Interfere 電磁干擾濾波器define 解釋emittor 放射極deflection 偏轉EN:engineer notice 工程通知degree 角度enclosure 包圍delete 刪除engineering specification 工程規范delivery 交貨enter 確認進入delivery order 送貨單environmental 環境的decide 解決決定裁決equivalent 等效description 規格說明error 錯誤destination 目的地ESD:electrical static discharge 靜電detail 明細estimate disable 預定的deviate 偏差excess 過剩diagonal 對角線exchange 交換differential amplifier 差分放大器exhausted 耗盡digital control multiscan color monit 數控多頻掃瞄彩色顯示explanation 解釋diode 二極体explode 使爆炸direct 直接external 外面的direct current 直流電disable 使無能factory 工廠discharge 泄放fail 失敗discriminate 區分fan 扇子disk driver 硬盤驅動器FBT:fly back transformer 高壓包display 顯示展示feature 特性display power management signal 顯示器電源管理信號feedback 回饋回接(geometry)distortion (几何)失真fotter plate 底座壓制片distribution 令發分配film stretch wrap 包裝機台伸縮膠膜dot pitch 點距filter 濾波器document center 文件中心final approved 核準door 門finance 財務dot 點first floor 一樓double 雙倍的function led lens 顯是燈座double thread screw 雙牙螺絲(鎖塑膠)flange hex nut 防滑螺絲DQA:design qaulity assurance 設計品質驗證課flat square screen 平面直角屏幕drop test 落下測試flex cable 多蕊電量dynamic 動態flow 流量dynamic performance defeat 動態測試不良flux 電通量dynamic HV 動態高壓flyback 返馳foot pad 角墊ear phone b/d 耳機機板foot-lamberts FL 亮度單位ECN:engineering change notice 工程變更通知form 表單ECR:engineering change request 工程變更申請format 格式化edit 編輯frame 構架electronic 電子F/C front cover 前殼fuse resistor 保險絲電阻information 信息function 功能運行input 投入function key 功能鍵input signal 輸入信號function test 功能測試inquiry 查詢fabricate 制作裝配inrush current 開機電流fuse 保險絲insert 插入fuse clip 保險絲座inspection 檢驗future 將來inspector 檢驗者instruction card 指示卡(牌)gap 縫隙insufficient solder 焊錫不足Gauss 高斯(磁場單位)insulation wire 絕緣導線generate 產生interiaced 交織geometry ate fixture&program internal audit 內部審核geometric distortion 几何失真invar 一種低澎脹合金goal 目標inventory 存貨good 良品好的invoice 發票good finished 成品IPQC:in process quality control 制程品質管制graphic 圖形IQC:incoming quality control 進料品質管制gross 總的ISO:international standard organizat 國際標準化組織gross request 總需求issue quantity 發料量guarantee 保證item 項目guide rail PC板保護條item master 料號主檔heat sink 散熱片jitter 抖動height 高jumper wire 跳線HI-POT OK label 高壓OK標籤junction 連接結HI-pot test 高壓測試high priority(use substitution item fi 第一優先(代用料)L/P:light&play L/P測試動態測試highlight 突出label 標簽hold 拿放抑制控制led 指示燈horizontal 水平的life test 壽命測試hot melt adhesives 熱容膠line date 上線日harness 排線linear filter 線性濾波變壓器humidity 濕度linearity 線性link bar 連接焊linear integrated circuit 線性集成電路local 本地的IC power 功率集成電路login 登入IC socket IC插座logout 登出IC(digital) AC 數位集成電路low radiation 低幅射IC(integrated circuit)集成電路luminance 揮發發揮idle 呆料illuminate 照亮MO:manufacture order 制令工單imagine sharpness 圖像清晰度M.T.B.F:mean time between failure 平均故障時間inductance 電感machine screw 機械螺絲inductor 電感器main 主要的第 3 頁共 13 頁LME F第 2 頁共 13 頁G H I Jmain board 主機板mainland 大陸name plate 裝飾片maintain 維護negative 否定的反向的負極性 major 主要的net shortage 淨需求maker 制造者network 綱路management 管理安排new model check list 新機種一線檢查表manual 說明書NG=NOT GOOD 非良品manual 用手的人工的說明書notice 通知manual PR 人工 PR NUT 螺帽manufacturing 制造master 主人掌握obligation 義務責任material 物料ohm 歐姆(電阻單位)material approve 物料承認書order 訂單material return 退料on hand 庫存maylar(capacitor)聚乙酯樹酯電容option 選擇MC:material control 物料控制OQC:out going quality control 出貸品質管制MCR:mechanical changed request 機構變更申請order balance 訂單余數MDR:material defeat report 物料不良報告original 最初ME:manufacture engineering 制造工程original material 原始材料本料measurement 測量outline 輪廓MEB(capacitor)金屬化多元指電容mechanical 機構的P.O:purchase order 採搆訂單melt 熔化熔解P.R: purchase request 採搆需求menu 菜單metal washer 金屬墊圈packing 包裝meter 測量儀表packing label 包裝祇箱標簽method 方法packing list 包裝明細MFG:manufacturing 制造pad 軟墊圈MI:manual insertion 手工插件pallet 棧板minor 次要的輕微的parameter 參數MIS:manage information system 資訊部part NO P/N 料號model 機種型號password 密碼口令model label(ID label)機種標籤payment term 付款期限model name 機種名稱PC:production control 生產控制MOF resistor 金屬膜電阻PCB board film PCB圖片moire 波紋PCB ckt PCB上位置monitor 顯示器PCB:print Circuit Board 印制線路板monthly 月度的PE BAG PE 袋MOS-FET 金氧場效電晶體PE:production engineering 產品工程MPP(capacitor)金屬化多元指電容peaking 峰值MRP FCST LIST MRP需求預測表relay 繼電器MRP:material request plan 物料需求計劃percentage 百分率MTL:material control 物料部資材部perform 履行magnetic field 磁場perform your own function 發揮自己的功能multiple 复合的多層次的performance 作業操作表演pilot lamp 指示燈recall复位收回pin assignment 管腳排布receiving接收pitch 間距receiving store收料倉pixel 象素象元receiving report收料報表plastic resin 合成松香rectangle矩形長方形plug 轉接頭rectifier整流器problem 問題,難題reduce減少plug and play 即插即用regulation管理調整規則polyfoam 保麗龍reject reason判退原因posistor 熱敏電阻reject判退posistor resistor 熱敏電阻(正溫度系數)relation關係positive 正極性的relay繼電器power 功率電力電源reply答复power cord 電源線request quatity需求量power knob 開關按鍵requirement要求power MO-SFET 功率晶體resistor電阻power switch 電源開關resolution解析度prevent 防止預防result結果prepared 放置模式準備resultant合成的結果preset mode 預調(畫面)retrace追蹤探查priority 優先revision修訂版procedure 程序過程rework重工processing 處理ripple波紋漣綺product tree diagram 產品樹狀圖rivet卯釘production 生產rotary VR:Variable Resistor可旋轉的可變電阻project engineer 項目工程師row行promote 促使rubber pad橡膠墊片proposed 建議,推薦power mos driver電源MOS驅動器protection 保護public inquiry 公共查詢sponge海棉public report 公共報表spring彈簧pulse 脈沖stability穩定性PUR purchase 採購購買standard標準的PVC insulator PVC 絕緣片static靜態的status狀況rag 抹布stock庫存品random 隨機的store儲藏range 範圍SUB assembly半品代號raster 光柵光域substitution代替替代代用料rate 比率suggestion建議意見ratings 預定值summary慨括R/C:rear cover 後殼supply供應reason 原因support支撐reason code 原因代碼surge 振蕩R P第 5 頁共 13 頁第 4 頁共 13 頁NOSP.S.I:production shippment inventionretail 零售suspend/stand by 中止/暫停等待等命swivel 旋轉speaker Assembly 喇叭組裝swivel ball底坐圓盤spec list 規格清單swivel base底盤spec 規格symopom現象special 特殊的synchronization同步specification 規格system系統status 狀況S.O :sale order業務訂單stock 庫存品S.O:shop order工單store 儲藏S.W:diode整流二極體SUB assembly 半品組裝S/N:series no流水號substituuon 代用的代用的safety code安規代碼suggestion 建議意見safety stock安全庫存summary 慨括sample樣品supply 供應schedule計劃support 支撐scope範圍screw 螺絲scrap報廢socket 插座screw螺絲swivel 旋轉screw+washer螺絲加墊片swivel ball 球座second source代用料swivel base 底盤sequence順序symoboy 現象selection選擇synchronization 同步separtesync分開信號system 系統series NO.系列號set up設立TANT(capacitor)鉭質電解電容shift轉移變化tape 膠帶shielding cover隔離罩tapping screw 缺口自攻螺絲ship date出貨日期target 目的shipment出貨TE:test engineering 測試工程shipping schedule 出貨計劃temperature 溫度shipping store出貨倉term 期限時限shortage缺料test pin 測試針插頭管腳shortage quantity缺料量test template 測試樣品signal to noise倍噪sponge 海棉simulation模擬模仿spark gap 放電管size by inch寬度thyristor ser 可控整流器slide SW/PUR SW/TACT 滑動/電源開關tilt 傾斜switch開關timing update 及時修改solder焊接焊接劑tolerance 容限誤差solder wire錫絲top/bottom 頂/底source資源TOTAL 總計spacer support間隔柱扣子trade 貿易商業spare parts備用品transter 調動spark gap放電隙transistor 三極管spark tube放電管transistor(TR)電晶體speaker 喇叭voltage/frequency 電壓/頻率VR knob 旋紐video mode descriptions 可視方式描述VR 可變電阻video b/d(CRT BD)CRT板video cable 信號線wafer 晶片干膠片wafer 封箱紙company policy&procedure 公司制度與規章warehouse 倉庫coding system 物料編號系統warning label 警告標簽item master 項目表warranty card 保證卡BOM bill of material 各機種之物料冊width 寬度component specification 材料規格書WIP work in process 在製品SRA substitution request authorizati 使用代料授權書wire 線材ECN engineering change notice 工程變更通知書wire saddle 隔離束線座notification 聯絡單engineering specificaton 工程規格書X-RAY label 輻射標簽alignment specification 調整規格書xformer 變壓器inspection specificaton 檢驗規格書xformer hordrive 水平驅動變壓器assembly process 制程指導書xformer pincusion 線性調整變壓assembly drawing 裝配圖xformer power 電源變壓器control run 小量試作管制MAP manufacturing assurance plan 制造品質保證計劃zenar diode 穩壓二極体check list criteria 檢驗表及標準uncommon list 機種差異表u/p unit price 單價CAR corrective action report 矯正改善報告uncommon list 專用材料表差異表SOP standard operation process 標準操作程序under request 超耗GR&R gauge reliability&repeatabili 可靠性標準校驗unformity 均衡性OSD INT MENU OSD功能說明upc label 客戶代碼標簽contrast 對比urgent 緊急的brightnes 亮度user control and indicate 用戶控製的及提示H.SIZE(H.=horizontal)水平尺寸user 使用者用戶H.Position 水平相位V.SIZE(V.=vertical)垂直尺寸V.D.S vender delivery schedule 廠商交貸計劃V.position 垂直中心VAL 單位V.pincushion 垂直針墊valid 有效的trapezoid 不規則四邊形variation 變化PIN/BALANCE 內凹/外凹varister 變阻器parallelogram 平行四邊形varistor resistor(vr)可變電阻rotation 旋轉傾斜video display interface 視頻顯示器接口color 顏色vendor 廠商 language 語言vertical 垂直的DISP.FREQ.(Display frequency)頻率顯示VESA:vedio electronic standard asso 示頻電子標準協會degauss 消磁VGA video graphic adapter 視頻圖形適配器recall 復歸VIA 通過H.moire H.一種有波紋的絲綢video cabel 信號線V.focus 垂直聚焦第 6 頁共 13 頁V 主要資料與文件W 第 7 頁共 13 頁T Z U Xvibration震動vibration test 震動測試PRE-alignment 1預調 1magnet 磁鐵PRE-alignment 2預調 2selicone 矽膠PRE-alignment 3預調 3glue 白膠rag 抹布hand gloves 手套burn in retest 加溫複檢cleaning solvent 清潔劑white balance 白平衡調整packing tape 膠帶center raster 底色調整lift pallet 棧板purity 色純hand lift 油壓車convergence=CG 收歛cart 手推車tilt 傾斜調整畫面不良代碼ATE 几何自動調整poor F/V adj 頻率轉換不良inspection 檢驗poor vertical 垂直不良INSP.2(convergence)收歛檢驗vert. over scan 垂直過大INSP.3(final)最終檢驗vert under scan 垂直過小safety inspection 安規檢驗poor vert linearity 垂直相性不良R/C screw 鎖後殼poor vert center 垂直中心不良R/C inspection/preparation 後殼檢驗與準備poor vert sync 垂直同步不良HI-POT test 高壓漏電測試vert damping 垂直反折cable tie 綁訊號線spot when power ON/OFF 關機打點monitor carrier 顯示器搬運vert white bar 一縱線packing station 包裝站別hor over scan 水平過大cleaning and wiping 去污與擦淨hor under scan 水平過小carton label 紙箱標簽retrace line 歸線model label 機種標簽hor no sync 水平不同步packing plastic 包裝塑膠袋子hor damping 水平反折putting manual 放入說明書手冊poor screen 畫面不良packing-carton box 包裝-紙箱poor center 水平中心不良finished goods filling 完成的貨物裝填dog ear 線性扭曲.拉角repair 修理poor hor linearity 左右大小格生產線常用名辭認識poor hor phase 水平相位不良board pallet 板子trap distortion 梯型不良stopper 踏板pincushipon distortion 針墊形不良electric screw driver 電槍smear 拖色拖影glue gun 膠槍red bias 紅色偏壓cutter nip 斜口鉗green bias 綠色偏壓long nose nip 長鼻鉗blue bias 藍色偏壓soldering iron 烙鐵red drive 紅色驅動solder lead 錫絲green drive 綠色驅動 45VPPdesoldering gun 吸錫器blue drive 藍色驅動multitester 三用電表poor focus 聚焦不良adjuster 調棒no picture 無影像hamlet chamber 磁場brightness too dark 畫面過暗counter 計數器相反raster show 底色不良color analyzer 色溫儀poor brightness F4F4不良poor contrast control 對比控制不良function key board Function key BDpoor brightness control 亮度控制不良audio board Audio BD poor G2G2控制不良speaker 喇叭poor bottom 按鍵無作用MIC phone 麥克風led off LED击陷不亮styrofoam 保麗龍tilt 縫隙.傾斜PE bag 塑膠袋F/C logo poor print 面框/印刷不良carton 紙箱poor video cable 信號線不良resistor 電阻insulator panel 安規片作業不良capacitor 電容poor covergence 收歛不良coil 電感(線圈)poor purity 色純度不良transistor 電晶體poor CRT CRT不良field effect transistor 場效電晶體no power 無電源integrated circuit 積體電路poor power saving 省電不良diode 二極體no raster 無光域variable resistor 可變電阻flash LED LED閃爍high voltage transformer 高壓變壓器smoking 冒煙.跳火yoke 便向軛poor degauss 消磁作用不良antenna 天線poor power SW 開關作用不良speaker 揚聲器poor start UP 起動不良poor voltage 電壓不良poor Hi-pot test 高壓測試不良not completely assembly 組裝未入interference 干擾reverse assembly 組裝反向moire 紋路assembly of lost part 組裝缺件noise 異聲.雜音poor wire dressing 佈線不良waggle 抖動.幌動.閃爍poor operating 作業不良ENGLISH DESCRIPTION poor assembly 組裝不良damage 損壞問題ground wire 接地線damage board PCB損壞degaussing coil 消磁線圈damage parts 零件損壞tilt coil=Rotation coil 傾斜線圈damage wire 線材損壞other wire 其他線材copper pad rising 銅箔翹皮anode cap 高壓帽cpper pad on board is broken 銅箔斷裂signal cable 信號線INSERTING PROBLEM插件問題label 標籤parts lost in AI AI缺件screw 螺絲wrong parts in AI AI錯件function key 功能鍵parts reversed in AI AI極性反front cover=F/C 前框parts is not insert into AI AI未插入rear cover=R/C 後框redundant parts in AI AI多件UL shield cover UL 安規片parts lost in MI MI缺件EMI shield cover EMI電磁干擾防護片wrong parts in MI MI錯件MPR II shield cover 幅射防護片parts reversed in MI MI極性反第 9 頁共 13 頁(組裝/包裝問題)第 8 頁共 13 頁CHINESE敘述(組裝段站別)FINAL ASSEMBLY STATION ALIGNMENT STATION (調整段站別)ASSEMBLY/PACKING PROBLEMmain boardMain BD(主機板)parts is not insert into MI MI未插入CRT boardCRT BD redundant parts in MI MI多件LED board LED BD components short each other 短路至其他部份others 其他moire水波紋ALIGNMENT PROBLEM 調整問題jitter/waggle畫面跳動/搖擺voltage adjust 電壓調整pix flash畫面閃爍function align 功能調整poor focus聚焦不良mechnical adjust 機構調整XRP CKT mal-functionXRP動作不良others 其他調整 F.W.T敲打不良OTHER PROBLEM 其他問題mute NG切換畫面不良beyond economic repair 非經濟維修other picture problem其他畫面不良difficult repair 修護困難red bias紅色偏壓engineer problem 工程問題green bias綠色偏壓no fail found 沒有不良發現blue bias藍色篇壓rework 重工red drive紅色驅動parts defect 零件不良green drive綠色驅動component defect 零件不良blue drive藍色驅動color change書色變色smear/tailing模糊/拖影cold solder/dry joint 冷焊/空焊different color at H&V line水平&垂直不同色older broken 錫點破裂impurity/doming色純度不良solder ball/solder short 錫球/錫短路blemish/phospher lost污點solder less 吃錫不良bri.too dark書面過暗others 其他raster show底色出現Hor. over/under scan 水平寬度過大/過小block L/O out of spec小方塊亮度超出規範poor hor.linearity 水平線性不良ABL L/O out of spec全白亮度超出規格hor.no sync 水平不同步poor contrast control對比控製不良hor fold over 水平反折poor bri. Control亮度控製不良poor hor center 水平中心不良poor G2 control G2控製不良poor hor phase 水平相位不良other color problem 其他顏色不良spot when power on/off 開/關機打點L/R output unbalance左右聲音輸出不平衡vert.collapse 一縱線L/R no put左右聲音不輸出vert over/under scan 垂直高度過大/過小Buzz 共振聲poor vert.linearity 垂直線性不良noise雜音vert.no sync 垂直不同步sound putput intermittent聲音輸出斷續vert.fold over 垂直反折Ear jack test failure耳機測試不良poor vert.center 垂直中心不良Microphone test failure麥克風測試不良vert.white bar 白Bar Other audio problem其他聲音不良retrace line 歸線NO power無電源hor.collapse 一橫線poor power saving省電功能不良geometry distortion 几何失真LED flash/power can't start-upLED閃爍&無法開機dog ear/top hook 扭曲/拉角smoke冒煙/跳火tilt 傾斜poor degaussing消磁不良no picture 無影像unit can't start-up起動不良pincushion distirtion 針墊不良hi-pot test failure高壓測試不良poor CG 收歛不良GND continue failure導通不良poor screen 畫面不良poor voltage電壓不良interference 干擾poor freg 除頻不良poor dymanic focus 動態聚集不良lack of manpowerpoor F/V adj 頻率轉換不良11.升降機故障High voltage leakage 高壓漏電lifter defectiveother power problem 其他電源不良12.ECN切入,REWORKGap 空隙engineering change notice reworkLoosen 松動13.設計問題,REWORKnot smooth 未平貼design problem, reworkpoor packing 包裝不良14.材料需全檢scratch/broken 損傷/破裂materials hold need sortingchange shape 變形body 毛邊operation 操作poor printing 印刷不良approve 贊成dirty 髒group 群.組(團体)other cosmetic problem 其他外觀不良leader 領班ICT TEST FAILURE ICT測試不良repair 修理micro ctrl latch-up 微電腦控制鎖住warehouse 倉庫micro ctrl data loss 微電腦控制資料遺漏trouble shooter 技術員DDC data error 寫入資料錯誤transfer 調動DDC data can't write-in 資料無法寫入manpower 人力function key can't work 功能鍵不動作DAY/NIGHT SHIFT 日/夜班(線)poor OSD display OSD顯示不良highlight 用強光照射(指提出重大事件)poor ATE ATE無法調net 淨效率Poor USB USB不良gross 毛效率goal 終點目標1.前殼不足total 總計的line stop/down time(front case shortage)workers 勞動者2.後殼不足urgent 緊急line stop/downtime(rear cover shortage)vertical 垂直3.材料不足horizontal 水平materials/parts shortage procedure 程序4.機構問題control run 小量試作mechanical design defective chassis 基板5.電氣問題inspection 檢驗technical design defective dynamic focus 動態聚焦6.加溫室故障tighten 提高規格burn-in room defective arching 跳火7.生產設備故障guide rail chassis 基板導軌production machine defective carton 紙箱;隔板類程序錯誤drop test 落下實驗program error support 支援(或支架)8.ATE故障combine 合併第 11 頁共 13 頁停線原因中英對照第 10 頁共 13 頁焊錫問題常用單詞SOLDERING PROBLEMATE defectiveseparate 分開9.包裝設備故障solution 對策packing machine defectiveaffirm 10.人員不足確定或確認(常用於新材料確認上)confirm Finance Department (FIN)加強;確認;批準(常用於對事情是否有確認)17.材料控制(物控)control panelMaterial Control (MC)(DAGGER機種的面板)18.生產控制(生管)follow-upProduction Control (PC)強制執行(對事情要確實實施)19.文件中心phase outDocument center 停用;或漸漸停產(用於機種或材料停用) 20.研發處color uniformityR/D Division=Research/Disign Division 色度一致性(指差異值) (a).電氣設計部brightness uniformity B/UElectrical design dept 亮度一致性(指百分比差異值)技術支援課T echnological support section Department 部門文件室1.產品工程部Document room Product Engineering Department(PE) (b).機構設計部2.測試工程部Mechanical design dept Test Engineering Department(TE) (c)專案管理部3.製造工程部Project Management DepartmentManufacture Engineering Department(ME)4.廠務工程部Factory Engineering Department(FE)5.資材部Material Department6.採購部Purchase Department7.人資部Human Resource Department8.自插部Auto Insertion Department9.品保部Quality Assurance Department10.進料品質管制In Coming Quality Control (IQC)11.製程品質管制In Process Quality Control (IPQC)12.出貨品質管制Out going Quality Control (OQC)13.品質工程Quality Engineering (QE)14.資訊部Management Information System(MIS) 15.制造部Manufacturing Department (MFG)16.財務部第 13 頁共 13 頁各部門中英文對照表第 12 頁共 13 頁。
工厂专业词汇大全
[工厂专业词汇大全] 出处:鸿海精密大陆龙华厂组装、冲压、喷漆等专业词汇Assembly line 组装线Layout 布置图Conveyer 流水线物料板Rivet table 拉钉机Rivet gun 拉钉枪Screw driver 起子Electric screw driver 电动起子Pneumatic screw driver 气动起子worktable 工作桌OOBA 开箱检查fit together 组装在一起fasten 锁紧(螺丝) fixture 夹具(治具) pallet 栈板barcode 条形码barcode scanner 条形码扫描仪fuse together 熔合fuse machine 热熔机repair 修理operator 作业员QC 品管supervisor 课长ME 制造工程师MT 制造生技cosmetic inspect 外观检查inner parts inspect 内部检查thumb screw 大头螺丝lbs.inch 镑、英寸EMI gasket 导电条front plate 前板rear plate 后板chassis |'∫asi| 基座bezel panel 面板power button 电源按键reset button 重置键Hi-pot test of SPS 高源高压测试V oltage switch of SPS 电源电压接柆键sheet metal parts 冲件plastic parts 塑料件SOP 制造作业程序material check list 物料检查表work cell 工作间trolley 台车carton 纸箱sub-line 支线left fork 叉车personnel resource department人力资源部production department 生产部门planning department 企划部QC Section 品管科stamping factory 冲压厂painting factory 烤漆厂molding factory 成型厂common equipment 常用设备punching machine 冲床robot 机械手hydraulic machine 油压机lathe 车床planer |'plein | 刨床miller 铣床grinder 磨床driller 钻床linear cutting 线切割electrical sparkle 电火花welder 电焊机staker=reviting machine 铆合机position 职务president 董事长general manager 总经理special assistant manager 特助factory director 厂长department director 部长deputy manager |'depjuti| =vice manager 副理section supervisor 课长deputy section supervisor =vice section supervisor副课长group leader/supervisor 组长line supervisor 线长assistant manager 助理to move, to carry, to handle 搬运be put in storage 入库pack packing 包装to apply oil 擦油to file burr 锉毛刺final inspection 终检to connect material 接料to reverse material 翻料wet station 沾湿台Tiana 天那水cleaning cloth 抹布to load material 上料to unload material 卸料to return material/stock to 退料scraped |'skrapid| 报废scrape ..v. 刮;削deficient purchase 来料不良manufacture procedure 制程deficient manufacturing procedure制程不良oxidation |' ksi'dei n| 氧化scratch 刮伤dents 压痕defective upsiding down 抽芽不良defective to staking 铆合不良embeded lump|in'bed| |l mp| 镶块feeding is not in place 送料不到位stamping-missing 漏冲production capacity 生产力education and training 教育与训练proposal improvement 提案改善spare parts=buffer 备件forklift 叉车trailer=long vehicle 拖板车compound die 模die locker 锁模器pressure plate=plate pinch 压板bolt 螺栓name of a department 部门名称administration/general affairs dept总务部automatic screwdriver 电动启子thickness gauge 厚薄规gauge(or jig) 治具power wire 电源线buzzle 蜂鸣器defective product label 不良标签identifying sheet list 标示单screwdriver holder 起子插座pedal 踩踏板stopper 阻挡器flow board 流水板hydraulic handjack 油压板车forklift 叉车pallet 栈板, (装卸、搬运货物用的)托盘,货板,集装架glove(s) 手套glove(s) with exposed fingers 割手套thumb 大拇指forefinger 食指midfinger 中指ring finger 无名指little finger 小指band-aid 创可贴industrial alcohol 工业酒精alcohol container 沾湿台head of screwdriver 起子头sweeper 扫把mop 拖把vacuum cleaner 吸尘器rag 抹布garbage container 灰箕garbage can 垃圾箱garbage bag 垃圾袋chain 链条jack 升降机production line 流水线chain 链条槽magnetizer 加磁器lamp holder 灯架to mop the floor 拖地to clean the floor 扫地to clean a table 擦桌子air pipe 气管packaging tool 打包机packaging 打包missing part 漏件wrong part 错件excessive defects 过多的缺陷critical defect 极严重缺陷major defect 主要缺陷minor defect 要缺陷not up to standard 不合规格dimension/size is a little bigger尺寸偏大(小)cosmetic defect外观不良,装饰性的;表面的slipped screwhead/slippery screw head 螺丝滑头slipped screwhead/shippery screw thread 滑手speckle 斑点mildewed=moldy=mouldy 发霉rust 生锈deformation 变形burr(金属)flash(塑件)毛边poor staking 铆合不良excessive gap 间隙过大grease/oil stains 油污inclusion 杂质painting peel off 脏污shrinking/shrinkage 缩水mixed color 杂色scratch 划伤poor processing 制程不良poor incoming part 事件不良fold of pakaging belt 打包带折皱painting make-up 补漆discoloration 羿色water spots 水渍polishing/surface processing 表面处理exposed metal/bare metal 金属裸露lack of painting 烤漆不到位safety 安全quality 品质delivery deadline 交货期cost 成本engineering 工程die repair 模修enterprise plan = enterprise expansion projects企划QC 品管die worker 模工production, to produce 生产equipment设备to start a press开机stop/switch off a press关机classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products, up-to-grade products 良品defective products, not up-to-grade products不良品waste废料board广告牌feeder送料机sliding rack滑料架上午10:36 2005/6/2die change 换模to fix a die装模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料transportation运输(be)qualified, up to grade合格not up to grade, not qualified不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for 准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位lots of production生产批量steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify修订to switch over to, switch---tothrow--over switching over切换engineering, project difficulty工程瓶颈stage die工程模automation自动化to stake, staking, reviting铆合add lubricating oil加润滑油shut die架模shut height of a die架模高度analog-mode device类模器die lifter举模器argon welding氩焊vocabulary for stamping 冲压常词汇stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivery to. to send delivery back to return of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking (be)broken,(be)cracked 断裂to lubricate润滑common vocabulary for die engineering 模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die连续模compound die复合模punched hole冲孔panel board镶块to cut edges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line stretching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder活页夹file folder文件夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerazation装箱quantity of physical invetory second count 复盘点数量quantity of customs count 会计师盘点数量blank and waste sheet NO. 空白与作废单号the first page 第一联bill name单据名称filed by accounting department for reference 会计部存查end-user/using unit(department) 使用单位summary of year-end physical inventory bills 年终盘点截止单据汇总表This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点incoming material to be inspected进货待验sample样品description品名steel/rolled steel钢材material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by 核准/审核/承办PCE assembly production schedule sheetPCE组装厂生产排配表model机钟work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity账面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion draw展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条形码flow chart流程窗体assembly组装stamping冲压molding成型spare parts=buffer备品coordinate坐标dismantle the die折模auxiliary function辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave 凹convex 凸short射料不足nick缺口speck瑕疪shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴angular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension draw展开图procedure draw工程图die structure draw模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板)stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing block衬套cover plate盖板guide pad导料块塑件&模具相关英文compression molding压缩成型flash mold溢流式模具compress mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口质量人员名称类fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=2.5~3.5mm diaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣IQC incoming quality control 进料质量管理人员TQC total quality control 全面质量管理PQC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 质量工程人员质量保证类FAI first article inspection 新品首件检查FAA first article assurance 首件确认TVR tool verification report 模具确认报告3B 3B 模具正式投产前确认CP capability index 能力指数CPK capability index of process 模具制程能力参数SSQA standardized supplier quality 合格供货商质量评估OOBA out of box audit 开箱检查QFD quality function deployment 质量机能展开FMEA failure model effectiveness analysis 失效模式分析FA final audit 最后一次稽核CAR corrective action request 改正行动要求corrective action report 改正行动报告FQC运作类AQL Acceptable Quality Level 运作类允收质量水平S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ Average Output Quality 平均出厂质量AOQL Average Output Quality Level 平均出厂质量Q/R/S Quality/Reliability/Service 质量/可靠度服务MIL-STD Military-Standard 军用标准S I-S IV Special I-Special IV 特殊抽样水平等级P/N Part Number 料号L/N Lot Number 特采AOD Accept On Deviation 特采UAI Use As It 首件检查报告FPIR First Piece Inspection Report 百万分之一PPM Percent Per Million 批号制程统计品管专类SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计质量管理R Range 全距AR Average Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GR&R Gauge Reproducibility&Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它质量术语类QCC Quality Control Circle 品质圈QIT Quality Improvement Team 质量改善小组PDCA Plan Do Check Action 计划执行检查总结ZD Zero Defect 零缺点QI Quality Improvement 质量改善QP Quality Policy 目标方针TQM Total Quality Management 全面质量管理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低质量水平RMA Return Material Audit 退料认可QAN Quality Amelionrate Notice 质量改善活动ADM Absolute Dimension Measuremat 全尺寸测量QT Quality Target 质量目标7QCTools 7 Quality Control Tools 品管七大手法通用之件类ECN Engineering Change Notes 工程变更通知(供货商) ECO Engineering Change Order 工程改动要求(客户) PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Specification In Process 制程检验规格SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QC Quality System 质量系统ES Engineering Standardization 工程标准CGOO China General PCE龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司T TAIWAN 台湾IWS International Workman Standard 工艺标准ISO International Standard Organization 国际标准化组织GS General Specification 一般规格CMCS C-China M-Manufact C-Compaq S-StampingCompaq产品在龙华冲压厂制造作业规范CQCA Q-Quality A-Assembly Compaq产品在龙华组装厂品管作业规范CQCP P-Painting Compaq产品在龙华烤漆厂品管作业规范部类PMC Production & Material Control 生产和物料控制PPC Production Plan Control 生产计划控制MC Material Control 物料控制ME Manufacture Engineering 制造工程部PE Project Engineering 产品工程部A/C Accountant Dept 会计部P/A Personal & Administration 人事行政部DC Document Center 数据中心QE Quality Engineering 质量工程(部) QA Quality Assurance 质量保证(处) QC Quality Control 质量管理(课) PD Product Department 生产部LAB Labratry 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供货商)标识符SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号其它OEM Original Equipment Manufacture 原设备制造PCE Personal Computer Enclosure 个人计算机外设PC Personal Computer 个人计算机CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大陆PRC People's Republic of China 中国大陆U.S.A the United States of America 美国A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存I/O Input/Output 输入/输出OK Ok 好NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electristatic Discharge 静电排放5S 希腊语整理,整顿,清扫,清洁,教养ATIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光盘CD-ROM Compact Disk Read-Only Memory 只读光盘FDD Floppy Disk Drive 软盘驱动器HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CA V Cavity 模穴CAD Computer Aid Design 计算器辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly Delivery Requirement 周出货需求C/T Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间) S/T Standard Time 标准时间P/M Product Market 产品市场3C Computer,Commumcation,Consumer electronic's 消费性电子5WIH When,Where,Who,What,Why,How to5M Man,Machine,Material,Method,Measurement4MIH Man,Material,Money,Method,Time 人力,物力,财务,技术,时间(资源) SQA Strategy Quality Assurance 策略质量保证DQA Design Quality Assurance 设计质量保证MQA Manufacture Quality Assurance 制造质量保证SSQA Sales and service Quality Assurance 销售及服务质量保证LRR Lot Reject Rate 批退率BS Brain storming 脑力激荡EMI Electronic Magnetion Inspect 高磁测试FMI Frequency Modulatim Inspect 高频测试B/M Boar/Molding(flat cable) C/P Connector of PCA/P AssemblySPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Video DiskVCD Video Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID ManufacturingCAE Computer AID EngineeringABIOS Advanced Basic in put/output system 先进的基本输入/输出系统CMOS Complementary Metal Oxide Semiconductor 互补金属氧化物半导体PDA Personal Digital Assistant 个人数字助理IC Integrated Circuit 集成电路ISA Industry Standard Architecture 工业标准体制结构MCA Micro Channel Architecture 微信道结构EISA Extended Industry Standard Architecture 扩充的工业标准结构SIMM Single in-line memory module 单项导通汇流组件DIMM Dual in-line Memory Module 双项导通汇流组件LED Light-Emitting Diode 发光二级管FMEA Failure Mode Effectiveness 失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Cable 扁平电缆PCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WPR Weekly Delivery Requirement 周出货要求PPM Parts Per Million 百万分之一TPM Total Production Maintenance 全面生产保养MRP Material Requirement Planning 物料需计划OS Operation System 操作系统TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProcedureEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material Size模具技术用语各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming 起泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 迭层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流檔板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 扥架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁)cavity retainer plate 模穴扥板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘脚flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶冲头headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶?lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块master plate 靠模样板match plate 分型板mold base 塑料模座mold clamp 铸模紧固夹mold platen 模用板moving bolster 换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paring line 分模线parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pilot pin 导?pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 扥料板return pin 回位梢riding stripper 浮动脱模器ring gate 环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide(slide core) 滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架spindle 主轴sprue 注道sprue bushing 注道衬套sprue bushing guide 注道导套sprue lock bushing 注道定位衬套sprue puller 注道拉料spue line 合模线square key 方键square nut 方螺帽square thread 方螺纹stop collar 限位套stop pin 止动梢stop ring 止动环stopper 定位停止梢straight pin 圆柱梢stripper bolt 脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱support pin 支撑梢supporting plate 扥板sweep templete 造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝模板模具常用之工作机械3D coordinate measurement 三次元量床boring machine 搪孔机CNC milling machine CNC铣床contouring machine 轮廓锯床copy grinding machine 仿形磨床copy lathe 仿形车床copy milling machine 仿形铣床copy shaping machine 仿形刨床cylindrical grinding machine 外圆磨床die spotting machine 合模机drilling machine 钻孔机engraving machine 雕刻机engraving E.D.M. 雕模放置加工机form grinding machine 成形磨床graphite machine 石墨加工机horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心internal cylindrical machine 内圆磨床jig boring machine 冶具搪孔机jig grinding machine 冶具磨床lap machine 研磨机machine center 加工制造中心。
工厂常用英文
工厂常用英文 Revised as of 23 November 2020部分工厂常用英文,供大家参考.Education and Training教育训练proposal improvement/creative suggestion提案改善BS Brain Storming 脑力激荡QCC Quality Control Circle 品质圈PDCA Plan Do Check Action 计划执行检查总结DCC delivery control center 交货管制中心3CComputer 计算机类产品Consumer electronics 消费性电子产品Communication 通讯类产品7SClassification整理(sorting, organization)-seiri Regulation整顿(arrangement, tidiness)-seiton Cleanliness清扫(sweeping, purity)-seiso Conservation清洁(cleaning, cleanliness)-seiktsu Culture教养(discipline)-shitsukeSave 节约Safety安全质量人员名称类QC quality control 品质管理人员FQC final quality control 终点质量管理人员IPQC in process quality control 制程中的质量管理人员OQC output quality control 最终出货质量管理人员IQC incoming quality control 进料质量管理人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 质量工程人员质量保证类FAI first article inspection 新品首件检查FAA first article assurance 首件确认CP capability index 能力指数CPK capability process index 模具制程能力参数SSQA standardized supplier quality audit 合格供货商质量评估FMEA failure model effectiveness analysis 失效模式分析FQC运作类AQL Acceptable Quality Level 运作类允收质量水平S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的Q/R/S Quality/Reliability/Service 质量/可靠度/服务P/N Part Number 料号L/N Lot Number 批号AOD Accept On Deviation 特采UAI Use As It 特采FPIR First Piece Inspection Report 首件检查报告PPM Percent Per Million 百万分之一制程统计品管专类SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计质量管理GRR Gauge Reproductiveness & Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径N Number 样品数其它质量术语类QIT Quality Improvement Team 质量改善小组ZD Zero Defect 零缺点QI Quality Improvement 质量改善QP Quality Policy 目标方针TQM Total Quality Management 全面质量管理RMA Return Material Audit 退料认可7QCTools 7 Quality Control Tools 品管七大手法通用之件类ECN Engineering Change Notice 工程变更通知(供货商)ECO Engineering Change Order 工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Standard Inspection Procedure 制程检验标准程序SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类ES Engineering Standard 工程标准CGOO China General PCE龙华厂文件IWS International Workman Standard 工艺标准ISO International Standard Organization 国际标准化组织GS General Specification 一般规格部类PMC Production & Material Control 生产和物料控制PCC Product control center 生产管制中心PPC Production Plan Control 生产计划控制MC Material Control 物料控制DC Document Center 资料中心QE Quality Engineering 质量工程(部) QA Quality Assurance 质量保证(处)QC Quality Control 质量管理(课)PD Product Department 生产部LAB Laboratory 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部生产类PCs Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供货商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号OEM Original Equipment Manufacture 原设备制造PC Personal Computer 个人计算机CPU Central Processing Unit 中央处理器As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量I/O input/output 输入/输出NG Not Good 不行,不合格C=0 Critical=0 极严重不允许APP Approve 核准,认可,承认CHK Check 确认ASS'Y Assembly 装配,组装T/P True Position 真位度5WIH When, Where, Who, What, Why, How to6M Man, Machine, Material, Method, Measurement, Message4MTH Man, Material, Money, Method, Time, How 人力,物力,财务,技术,时间(资源) SQA Strategy Quality Assurance 策略质量保证DQA Design Quality Assurance 设计质量保证MQA Manufacture Quality Assurance 制造质量保证SSQA Sales and service Quality Assurance 销售及服务质量保证LRR Lot Reject Rate 批退率SPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Video DiskVCD Video Compact DiskLCD Liquid Crystal DisplayCAD Computer Aided DesignCAM Computer Aided ManufacturingCAE Computer Aided EngineeringPCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WDR Weekly Delivery Requirement 周出货要求PPM Percent Per Million 百万分之一TPM Total Production Maintenance 全面生产保养MRP Material Requirement Planning 物料需计划OS Operation System 操作系统TBA To Be Assured 待定,定缺D/C Drawing ChangeP/P Plans & ProcedureEMI Electrical Magnetic Interference 电子干扰RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material SizeLED lighting-emitting diode 发光二极管QBR Quarter Business RecordCIP Continuous improvement processFGI Forecasted Goal InventoryCNC Computerized numeral controllerB2C Business to customerB2B Business to businessAVL Approved vendor listPOP Procedure of packagingEOL End of lifeVDCS Vender defect correcting sheet PDCS Process defect correcting sheetGRN Goods receiving noteA/R Accounting receivableA/P Accounting payable三:专业词汇通用类president董事长operator作业员position职务general manager总经理special assistant 特助deputy manager |'depjuti| =vice manager副理deputy supervisor =vice supervisor副课长group leader组长line leader线长supervisor 课长responsible department负责单位Human Resources Department人力资源部Head count 人头数production department生产部门QC Section品管课administration/general affairs dept./总务部production unit生产单位meeting minutes会议记录distribution department分发单位subject主题conclusion结论decision items决议事项pre-fixed finishing date预定完成日Color management 颜色管理Visual management 目视管理production capacity生产力first count初盘first check初盘复棹second count 复盘second check复盘复核quantity of physical inventory second count 复盘点数量physical inventory盘点数量physical count quantity账面数量difference quantity差异量spare parts physical inventory list备品盘点清单cause analysis原因分析waste materials废料description品名specification 规格model机种work order工令revision版次remark备注registration登记registration card登记卡to control管制application form for purchase请购单consume, consumption消耗to notify通知to fill in填写to collect, to gather收集statistics统计cosmetic inspection standard 外观检验规范computer case 计算机外壳(组件)personal computer enclosure 计算机机箱产品front plate前板rear plate后板chassis |'∫?si| 基座bezel panel面板Hood 上盖base pan 基座bezel 面板flat cable 排线resin film 树脂膜raw materials原料materials物料steel plate钢板roll/coil material卷料spare parts =buffer备品plastic parts塑料件sheet metal parts/stamping parts 冲件material check list物料检查表finished product成品semi-finished product半成品good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库packing material包材basket蝴蝶竺plastic basket胶筐flow chart流程窗体production tempo生产进度现状lots of production生产批量manufacture procedure制程to revise, modify修订to switch over to, switch—to, switching over切换engineering bottleneck, project difficulty工程瓶颈glove(s)手套glove(s) with exposed fingers割手套Band-Aid创可贴Industrial alcohol工业酒精broom扫把mop拖把vacuum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋liaison联络单rags抹布lamp holder灯架to mop the floor拖地to clean a table擦桌子air pipe 气管delivery deadline交货期die worker模工production, to produce生产equipment设备resistance电阻beacon警示灯coolant冷却液crusher破碎机plate电镀power button电源按键reset button重置键forklift叉车Workshop traveler 天车trailer =long vehicle拖板车Hydraulic trolley手压车hydraulic hand jack油压板车casing = containerization装箱velocity速度patent专利coordinate坐标supply and demand供求career card履历卡barricade隔板carton box纸箱to pull and stretch拉深work cell/work shop工作间sub-line支线bottleneck 瓶颈packaging tool打包机packaging打包品质类qualified products, up-to-grade products良品defective products, not up-to-grade products不良品defective product box不良品箱poor processing 制程不良poor incoming part来件不良exposed metal/bare metal金属裸露excessive defect过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格cosmetic defect外观不良lack of painting烤漆不到位slipped screw head/slippery slipped thread滑丝missing part漏件wrong part错件oxidation氧化defective threading抽芽不良poor staking铆合不良deficient purchase来料不良deficient manufacturing procedure制程不良cosmetic inspection外观检查inner parts inspection内部检查blister 气泡angular offset 角度偏差dent 压痕scratch 刮伤deformation 变形filings 铁削defective label 不良标签abrasion 磨损Breaking. (be)broken,(be)cracked 断裂short射料不足nick缺口speck瑕疪shine亮班splay 银纹gas mark焦痕delaminating起鳞speckle斑点mildewed =moldy = mouldy发霉deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excessive gap间隙过大grease/oil stains油污inclusion杂质shrinking/shrinkage缩水mixed color杂色fold of packaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍impurity 杂质Mismatch 错位failure, trouble 故障deformation 变形rust 生锈peel 脱漆Shrink 缩水Contamination 脏污water spots 水渍Gap 间隙label error 标签错误Missing label 漏贴rejection criteria 拒收标准Suspected rejects 可疑庇abrasion 损伤、磨损Texture surface 印花纹表面Streak 条纹stains 污点Blotch 斑点discoloration 脱色Inclusion 杂质slug mark 压痕dirt grime 灰尘blush 毛边薄膜sink 下凹Hickey 漏漆labels and logos 贴纸与商标Configuration labels 组合贴纸corrugated container 瓦摆纸箱Delaminating 脱层splattering 散点Gouge 锉孔puckering 折痕烤漆类phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉organic solvent有机溶剂demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料volatile挥发性degrease脱脂rinse水洗alkaline etch龄咬desmot剥黑膜. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔scraped products报放品disposed products处理品dismantle the die折模auxiliary function辅助功能heater band 加热片thermocouple热电偶derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response =reaction =interaction感应ram连杆edge finder巡边器concave凸convex凹cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线grit沙砾granule =pellet =grain细粒sand blasting喷沙grit maker抽粒机cushion缓冲fillet镶;嵌边roller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴组装类Assembly line组装线Layout布置图Conveyer流水线运输带Rivet machine拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Hydraulic machine 液压机Pneumatic screw driver气动起子automation自动化to stake, staking, riveting铆合add lubricant oil加润滑油argon welding氩焊cylinder油缸robot机械手conveying belt输送带transmission rack输送架to draw holes抽孔bolt螺栓nut 螺母screw 螺丝identification tag标示单screwdriver plug起子插座automatic screwdriver电动启子to move, to carry, to handle搬运be put in storage入库packing包装staker = riveting machine铆合机fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet/skid栈板barcode条形码barcode scanner条形码扫描仪fuse together熔合fuse machine/heat stake热熔机processing, to process加工delivery, to deliver 交货to return delivery to. to send delivery back to return of goods退货easily damaged parts易损件standard parts标准件to lubricate润滑spring 弹簧spare tools location/buffer手工备品仓spare molds location模具备品仓tox machine自铆机waste废料board广告牌sliding rack滑料架to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料material change, stock change材料变更feature change 特性变更prepare for, make preparations for 准备rotating speed, revolution转速abnormal handling异常处理工厂常用缩略语５Ｓ：５Ｓ管理ＡＢＣ：作业制成本制度 (Activity-Based Costing)ＡＢＢ：实施作业制预算制度 (Activity-Based Budgeting)ＡＢＭ：作业制成本管理 (Activity-Base Management)ＡＰＳ：先进规画与排程系统 (Advanced Planning and Scheduling) ＡＳＰ：应用程序服务供货商（Application Service Provider）ＡＴＰ：可承诺量 (Available To Promise)ＢＯＭ：物料清单 (Bill Of Material)ＢＰＲ：企业流程再造 (Business Process Reengineering)ＢＳＣ：平衡记分卡 (Balanced ScoreCard)ＢＴＦ：计划生产 (Build To Forecast)ＢＴＯ：订单生产 (Build To Order)ＣＰＭ：要径法 (Critical Path Method)ＣＲＭ：客户关系管理 (Customer Relationship Management)ＣＲＰ：产能需求规划 (Capacity Requirements Planning) ＣＴＯ：客制化生产 (Configuration To Order)ＤＢＲ：限制驱导式排程法 (Drum-Buffer-Rope)ＤＲＰ：运销资源计划 (Distribution Resource Planning) ＤＳＳ：决策支持系统 (Decision Support System)ＥＣ：设计变更／工程变更 (Engineer Change)ＥＣ：电子商务 (Electronic Commerce)ＥＤＩ：电子资料交换 (Electronic Data Interchange)ＥＩＳ：主管决策系统 (Excutive Information System)ＥＯＱ：基本经济订购量 (Economic Order Quantity)ＥＲＰ：企业资源规划 (Enterprise Resource Planning)ＦＭＳ：弹性制造系统 (Flexible Manufacture System)ＦＱＣ：成品品质管制 (Finish or Final Quality Control)ＩＰＱＣ：制程品质管制 (In-Process Quality Control)ＩＱＣ：进料品质管制 (Incoming Quality Control)ＪＩＴ：实时管理 (Just In Time)ＫＭ：知识管理 (Knowledge Management)Ｌ４Ｌ：逐批订购法 (Lot-for-Lot)ＬＴＣ：最小总成本法 (Least Total Cost)ＬＵＣ：最小单位成本 (Least Unit Cost)ＭＥＳ：制造执行系统 (Manufacturing Execution System)ＭＰＳ：主生产排程 (Master Production Schedule)ＭＲＰ：物料需求规划 (Material Requirement Planning)ＭＲＰⅡ：制造资源计划 (Manufacturing Resource Planning)ＯＥＭ：委托代工 (Original Equipment Manufacture)ＯＤＭ：委托设计与制造 (Original Design & Manufacture)ＯＬＡＰ：线上分析处理 (On-Line Analytical Processing)ＯＬＴＰ：线上交易处理 (On-Line Transaction Processing)ＯＰＴ：最佳生产技术 (Optimized Production Technology)ＯＱＣ：出货品质管制 (Out-going Quality Control)ＰＤＣＡ：PDCA管理循环 (Plan-Do-Check-Action)ＰＤＭ：产品数据管理系统 (Product Data Management)ＰＥＲＴ：计画评核术 (Program Evaluation and Review Technique) ＰＯＨ：预估在手量 (Project on Hand)ＱＣＣ：品管圈 (Quality Control Circle)ＲＣＣＰ：粗略产能规划 (Rough Cut Capacity Planning)ＲＯＰ：再订购点 (Re-Order Point)ＳＣＭ：供应链管理 (Supply Chain Management)ＳＦＣ：现场控制 (Shop Floor Control)ＳＩＳ：策略信息系统 (Strategic Information System)ＳＰＣ：统计制程管制 (Statistic Process Control)ＴＯＣ：限制理论 (Theory of Constraints)ＴＱＣ：全面品质管制 (Total Quality Control)ＴＱＭ：全面品质管理 (Total Quality Management)ＷＩＰ：在制品 (Work In Process)> ５Ｓ：５Ｓ管理5S是由JP企业研究出来的一种环境塑造方案，其目的在藉由整理(SEIRI)、整顿(SEITON)、清扫(SEISO)、清洁(SEIKETSU)及身美(SHITSUKE)五种行为来创造清洁、明朗、活泼化之环境，以提高效率、品质及顾客满意度。
工厂常用设备英语词汇
常用设备 台车 纸箱 支线 叉车 整平机 冲床 机械手 油压机 车床 刨床 铣床 磨床 钻床 线切割 电火花 电焊机 铆合机 组装线 流水线物料板 拉钉机 拉钉枪 起子 电动起子 气动起子 工作桌 夹具(检具) 栈板 条形码 条形码扫描仪 大头螺丝 冲件 塑料件 工作间 天那水 抹布 螺栓 电动启子 厚薄规 治具 电源线 蜂鸣器 踩踏板
44 stopper 45 flow board 46 hydraulic handjack 47 iudustrial alcohol 48 head of screwdriver 49 sweeper 50 mop 51 vaccum cleaner 52 rag 53 garbage container 54 garbage can 55 garbage bag 56 chain 57 jack 58 production line 59 chain 60 lamp holder 61 air pipe 62 packaging tool 63 feeder 64 packing material 65 isolating plate baffle plate; barricade 66 carton box
阻挡器 流水板 油压板车 工业酒精 起子头 扫把 拖把 吸尘器 抹布 灰箕 垃圾箱 垃圾袋 链条 千斤顶 流水线 链条槽 灯架 气管 打包机 送料机 包材 nt 2 trolley 3 carton 4 sub-line 5 lift fork 6 uncoiler and straightener 7 punching machine 8 robot 9 hydraulic machine 10 lathe 11 planer 12 miller 13 grinder 14 driller 15 linear cutting (wire cutting) 16 electrical sparkle 17 welder 18 staker = reviting machine 19 Assembly line组装线 20 Conveyer 21 Rivet table 22 Rivet gun 23 Screw driver 24 Electric screw driver 25 Pneumatic screw driver 26 worktable 27 fixture 28 pallet 29 barcode 30 barcode scanner 31 thumb screw 32 sheet metal parts 33 plastic parts 34 work cell 35 Tiana 36 cleaning cloth 37 bolt 38 automatic screwdriver 39 thickness gauge 40 gauge(or jig) 41 power wire 42 buzzle 43 pedal
工厂常用英语单词一览表
Defect describe
雜點 mottle 變形 deform 劃傷 scratch 彎曲 bent 斷裂 rupture 報廢 scrap 生鏽 rust 漏電 creepage 磨損 attrition 異常 abnormity 插入不良 poor insert 電鍍不良 poor plating 不良 defect 不良項目 failure items 不良率 defect rate 附著異物 adhere foreign substance 短路 short circuit
International Trade/Sales
補償貿易：Compensation Trade 市場： Market 進出口： import/export 來件裝配： Assembly from supplied components 來料加工： Processing good from buyers’ raw material 集裝箱運輸：containerization 合同：contract 出貨：shipment 採購： purchase 包裝： packaging 商業的： commercial 商業/交易：business 商人：merchant /business man /trader 客戶：customer 供應商：supplier/vendor
人事部 personnel Dep. 行政部 administration Dep. 品管部 quality control Dep. 工程部 engineering Dep. 采購部 purchase Dep. 財務部 accounting Dep. 業務部 Sales Dep. 關務部 Custom service Dep. 生產部 manufacturing Dep. 文件中心 document control center 資訊部 manage information system 品 保 quality assurance 插件部 auto-insertion (AI) 制程品質管制： in process quality control (IPQC) 進料品質管制： incoming quality control ( IQC) 出貨品質管制：outgoing quality control (OQC)
工厂常用英语词汇一览表
工廠常用英語詞彙一覽表；按字母查詢簡表1Rev:01；英文簡稱英文全名中文解釋；========================；5S5S整理,整頓,清掃,清潔,教養；66Sig ma六標準差；A/IAutoInsertion自動插件；AQLAcceptQualityLevel允收水；B /IBurn-In高溫熱機(老化)過程；BOMBillOfMaterial6 6 Sigma 六標準差A/I Auto Insertion 自動插件AQL Accept Quality Level 允收水準B/I Burn-In 高溫熱機(老化)過程BOM Bill Of Material 材料明細表BTO Build To Order 接單生產CAD/CAM Computer Aided Design/Manufacturing 電腦輔助設計/製造CAL Calibration 儀器校驗 (儀校)CAR Corrective Action Response 改善對策報告CCR Customer Complain Requirement 客戶抱怨/要求Charge Charge 索取費用CND Cannot Duplicate 無法複製,異常現象消失CR Critical 嚴重(CR>MA>MI)CS Customer Service 客戶服務CTO Configure To Order 接單組裝Debit Note Debit Note (會計) 帳目通知DELL's Survey Form DELL's Survey Form DELL公司稽核供應商的文件ECN Engineering Change Notice 工程變更通知ECR Engineering Change Request 工程變更要求EMI Electro Magnetic Interference 電磁干擾ENG Engineering 工程(部)ESD Electrostatic Discharge 靜電放電FAE Field Application Engineering 客訴前置處理單位FAI First Article Inspection 首件檢查FN Factory Notice 工廠通知FRR Field Return Rate 市場退修率FRU Field Replacement Unit 市場不良回修更換套件Hi-Pot Hi-Pot 耐電壓測試Hold Hold (shipping, production…) 停止 (出貨,生產…)ICT In-Circuit Test (PC板)電路測試IE Industrial Engineering 工業工程IPQC In-Process Quality Control 製程品質管制IQC Incoming Quality Control 進料品質管制ISO International Organization for Standardization 國際標准組織JIT Just In Time 即時 (行動,入料…)MA Major 主要ME Mechanical Engineering 機械工程MFG Manufacturing 製造部(業)MI Minor 次要MIS Management Information System 資訊管理系統MP Mass Production 量產 (亦指製造部)MRB Material Review Board VQA材料異常會閱MTBF Mean Time Between Failure 平均失效時間ODM Original Developing Manufacturer 原始設計生產OEM Original Equipment Manufacturer 原始配備生產O/I Operational Instruction 作業指導書ORT On-going Reliablity Test 在製品可靠度測試PDCA Plan Do Check Action 戴明循環PE Production Engineering 製造工程(部)P/N Part Number 品名P/R Pilot-Run 試作驗證Preforming Preforming 預加工P/O Purchase Order 採購下訂單(P/O->S/O->W/O)PPM Part Per Million 百萬分之一 (品質計算單位)QA Quality Assurance 品質保証QCQuality Control 品質管制QCCA Quality Control Circle Activities 品管圈活動QIS Quality Information System 品質資訊系統REV Revision 版本R/I Run-In 常溫熱機(老化)過程RMA Return Merchandise Approval(or Authorization) 退貨品認可RTV Return To Vendor 退回廠商Safety Safety 安全規格 (安規)SMT Surface Mounting Technology 表面黏著技術S/N Serial Number 序號S/O Sales Order 業務下訂單SPC Statistics Process Control 統計製程管制SPEC Specification 規格SWOT Strength Weaknesses Opportunities Threats 強勢弱勢潛在機會威脅TE Test Engineering 測試工程TPM Total Productive Maintenance 全面性生產維護TQM Total Quality Management 全面品質管理TUV TUV 德國萊茵技術監護顧問公司 (安規單位)UL Underwriters Laboratories 美國保險協會實驗室 (安規單位)VQA Vender Quality Approval 供應商品質保證 (雷同進料檢驗)WIP Work In Process 尚未完成的在製品W/O Work Order 生產工單電腦公司專有名詞縮寫釋義小集一. 企劃,產銷,采購,進出口專有名詞P/N ------ Part Number 料號P/R ------ Purchase Request (物控release給采購的)請購單P/O ------ Purchase Order (采購release給廠商的)訂單PMC ------ Production & Material Control 生管&物控管理PM ------ Production Management 整個生產管理(包括生管,物控,產銷) MC ------ Material Control (企劃)物控PC ,------ Production Control (企劃)生管PL,,------ Project Leader ,專案管理(針對大客戶大訂單的專門全面管理, 主要是Pilot Run 階段及其前期工作), OM ------ Order Management ,訂單管理(量產之後的訂單答交﹑生產進度跟蹤﹑工令管理﹑ECN變更﹑出貨排程等),PMP ------ Project Management Plan 專案(訂單)管理計劃書,PIC ------ Person In Charge (專案)負責人,COPP ------,ORT ------ Ongoing Reliability Test生產過程中的可靠度測試,UCL ------ Up Control Line 上管制線,LCL ------ Low Control Line 下管制線FAI ------PVT ------ Process Verification Test ,,Pilot Run試生產第一階段,先作PVT,再作MVB.MVB ------ Mass Verification Board ,Pilot Run試生產之第二階段M/P ------ Mass Production ,量產/大批量生產BTF ------ Build To Forecast ,依據銷售預測進行生產BTO ------ Build To Order , ,,依據訂單生產CTO ------ Configuration To Order 客製化生產PTD ------ Production To Departure,,,CRM ------ Customer Relationship Management 客戶關係管理,,,CRP ------ Capacity Requirements Planning 產能需求規劃, ERP ------ Enterprise Resource Planning 企業資源規劃,FMS ------ Flexible Manufacture System , 彈性製造系統BOM ------ Bill Of Material 物料清單MPS ------ Master Production Scheduling ,主生產排程,指根據業務接單或銷售預測所排定一段期間之產品生產計劃,須指定何種產,品應於何時製造完成多少數量.MRP ------ Material Requirement Planning 物料需求規劃,MRP之計算依照MPS之產品獨立需求,透過BOM展開之零組件相依需求,,配合當時存貨狀況,以求得某段期間內應投入生產或執行採購之計劃方針.,WIP ------ Work In Process 在製品,FG ------ Finished Goods ,制成品/產成品,E&O ------ Excess & Order/Backlog ,呆滯在途(訂單),EOL ------ End Of Line 產品壽命中止(停止生產),MES------Manufacturing Execution System製造執行系統輔助生管人員收集現場資料及控制現場製造流程,提供企業改善製程、提高生產效益的工具.大部分的MES系統模組皆會包括訂單管理系統(Customer Order Management, C OM)﹑物料管理系統(Material Management System, MMS)﹑製程式控制管系統(Work In Process Tracking, WIP)﹑生產排程系統(Production Scheduling S ystem, PSS)﹑品質控管系統(Statistical Process Control , SPC)﹑設備控管系統(Equipment Management System, EMS)及對外部系統的PDM整合介面(PD M Integration Interface)與ERP整合介面(ERP Integration Interface)等模組.,OEM ------ Original Equipment Manufacture 委託代工,,ODM ------ Original Design & Manufacture ,委託設計與製造AVL ------ Approved Vendor List 具備資格/被認可的廠商名冊SCM ------ Supply Chain Management 供應鏈管理SLM ------ Supply Line Management 供應鏈管理產品由起始原料轉換成完成品至最終到達顧客手上之流動過程中,影響其執行績效的個體組合而成之網路稱為供應鏈,供應鏈的組成個體可能包括：供應商→製造→工廠→配銷點→零售商→最終顧客;而供應鏈管理之定義,簡單而言,就是需求與供應適當的結合,以達到資源﹝人﹑設備﹑物﹑資金﹞運用與分配之有效性與及時性.,EC ------ Engineer Change 設計變更/工程變更,EC ------ Electronic Commerce 電子商務,ECN ------ Engineer Change Notice 工程變更通知書,S/O ------ Shipping Order 裝貨通知單S/A ------ Shipping Advice 出貨通知,比“SI”先行S/I ,------ Shipping Invoice 正式的出貨文件/發貨單P/L ------ Packing List , , (出貨)裝箱單B/L ------ Bill of Leading 提貨單/提單N/W ------ Net Weight 淨重ETD/E.T.D/e.t.d ------ Expected Time ,of Departure (貨船)預定開航時間,ETA/E.T.A/e.t.a ------ Expected Time, of Auuival 預定到達時間,CAT ------ Component Approval Team 零件承認組,KPI ------ Key Part Index 關鍵指標二.財務,會計專有名詞A/R ------ Account Receivable 應收帳款A/P ------ Account Payment 應付帳款Deduct AP ------ 扣除應付帳款/不良扣款T/T ------ Telegraph Transfer 匯轉帳(付款)OA 30天 ------ 貨到30天後付款(如11/5到貨,則12/5付款)月結30天 ------ 貨送到後下月底付款(如11/5到貨,則12/30付款) ID ------ Input Duty 關稅VAT ------ Value Add Tax 增值稅三. 品管專有名詞IQC ------ Incoming Quality Control ,, 進料品質控制IPQC------ In-Process Quality Control ,製程品質管制:產品未完成前,尚在製程中的品管工作FQC ------ Finish or Final Quality Control , 成品品質管制:成品未裝箱前的品管工作.QE ------ Quality Engineering , 品質工程FAE ------ Final Application Engineer 終端應用工程部門(屬R&D范疇)又稱為 AED --- Application Engineer Department.FAE ------ Finished Application Engineer 成品應用工程CPSR ------ Customer Product Standard Request 客戶產品規格標准要求QA ------ Quality Assure 品質保証OQA ------ Out-going Quality Assure , 出貨品質保証對廠內生產線的產品進行檢驗及測試, 范圍包括: 產品外觀,ECN是否最新版,產品結搆是否符合ECN,附屬配件是否齊全(CD-PRO,MENU),包裝方法是否符合客戶要求,產品性能檢驗測試(能否正常運行,與其他產品的相容性等).DIST機種用3種固定規格的CPU,HDD進行測試,專案機種按客戶提供的固定程式測試,項目相對較少,時間較短.OQA 0.0 ------ 出貨failure rate(不良率)為0.0%之品質保証OOB ------ Out Of Box 開箱檢查,包括產品功能及相容性測試除需進行與OQA相同的檢驗及測試之外,還要設法取得客戶資訊,模擬客戶端系統使用狀況進行產品相容性測試,對客戶可能采用的各種規格型號之HDD,CPU,FLOPPY等均需進行測試,,測試項目較多,,時間較長,所需的測試程式和測試治具比OQA要多,OQC ------ Out-going Quality Control 出貨品質管。
工厂常见英语
Base 底座 18、 bifilar 双线并绕 Bobbin 绕线管 checked by审核 20、 Choke电感 clip耳夹
21、 Brush Epoxy On Core 铁芯刷胶 22、 Brush Epoxy On Loop 线圈刷胶 23、 close winding密绕 component 组件 24、 condition条件 core铁芯 25、 condition条件 copper铜箔 立式 26、 Curing烘烤 current 电流 27、 Cut wire 裁线 28、 defective product box不良品箱 29、 deficient manufacturing procedure制程不良 30、 description: 说明 31、 dip 浸入 Direction 方向 32、 Electronic Magnetic In EMI 抗电磁干扰 33、 Enameled copper wire 漆包线 34、 ertment )
1、 QC quality control 2、 FQC final quality control 3、 IPQC in process quality control 4、 OQC output quality control 5、 IQC incoming quality control 6、 TQC total quality control 7、 POC passage quality control 8、 QA quality assurance 9、 OQA output quality assurance 10、QE quality engineering 11、FAI first article inspection 12、FAA first article assurance 13、TVR tool verification report 14、CP capability index 15、CPK capability index of process 16、SSQA standardized supplier quality 17、OOBA out of box audit 18、QFD quality function deployment 19、FA final audit 20、CAR corrective action request 品质管理人员 终点品质管制人员 制程中的品质管制人员 最终出货品质管制人员 进料品质管制人员 全面质量管理 段检人员 质量保证人员 出货质量保证人员 品质工程人员 新品首件检查 首件确认 模具确认报告 能力指数 模具制程能力参数 合格供应商品质评估 开箱检查 品质机能展开 最後一次稽核 改正行动要求
工厂常用英语大全
(會計) 帳目通知 Debit Note
高溫熱機(老化)過 B/I（Burn-In）& R/I（Run-In） 程 百萬分之一 (品質 PPM（Part Per Million） 計算單位) 戴明循環 極性反 漏件 錯件 壞件 無線尾 裝插不良 零件偏移 絕緣不良 成型不良 錫洞 錫多 近似短路 錫裂 錫渣 錫橋 冷焊 錫尖 短路 錫少 漏焊 翹皮 漏標示 線腳長 漏點膠 防焊漆膠落 污損 溫度 補焊 老化熱機 PDCA（Plan Do Check Action） polarity reversed missing part wrong part component no lead protruded improper insertion component shifted insulation damaged poor preforming solder void excessive solder near short solder crack solder spatter solder bridge cold solder solder icicle solder short solder in sufficient missing solder peeling off missing marking lead protrusion out of spec missing glue solder mask peeling off contamination temperature touch-up burn-in
零件方面 Component
零件方面 Component
扼流線圈 連接器 基板 二極體 樹脂 風扇 場效電晶體 濾波器 保險絲 保險絲底座 保險絲底座 膠 散熱片 集成電路 電感 絕緣片 跳線 標簽 接地唾形墊片 熱敏電阻 螺絲帽 屏蔽背板 三極管 膠布 自攻螺絲 機械螺絲 端子 變壓器 電晶體 套管 突波吸收器 可變電阻 墊片 齊納 光藕合二極體 穩壓器 電阻 鉚釘 螺絲 插座 錫棒 彈簧墊片 支柱 星形墊片 開關
工厂专业英语术语
工厂专业英语术语Assem bly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Pneumatic screw driver气动起子worktable 工作桌O OBA开箱检查fit together组装在一起fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse m achine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cos metic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch 镑、英寸EMI gasket导电条front plate前板rear plate后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS 电源电压接拉键sheet m etal parts 冲件plastic parts塑胶件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource depart m en t 人力资源部production depart ment生产部门planning depart m ent企划部QC Secti on品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common e quipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic m achine油压机lathe车床planer |'plein?|刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting m achine铆合机position职务president董事长general manager总经理special assistant m anager特助factory director厂长depart m ent director部长deputy m anager | =vice m anager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant m anager助理to m ove, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect m aterial接料to reverse m aterial 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load m aterial上料to unload m aterial卸料to return m aterial/stock to退料scraped |'skr?pid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient m anufacturing procedure制程不良oxidation |' ksi'dei?n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良em bedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车com pound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓administration/general affairs dept总务部autom atic screwdriver电动启子thicknes s gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单location地点present m embers出席人员subject主题conclusion结论decision item s决议事项responsible depart m ent负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准depart ment部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete m aterial良品已呆滞to be inspected or reworked 待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw m aterials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list 备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flam e cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die butto n圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopp er清角active plate活动板baffle plate挡块cover plate盖板m ale die公模fem ale die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetizat ion去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜 D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products 报放心品defective products不良品finished products成品disposed products处理品barcode 条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer 备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting m achine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction =interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕?? shine 亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grai n细粒grit m aker抽粒机cushion缓冲magnalium镁铝合金m agnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tem po生产进度现状torque扭矩spline=t he multiple keys花键quenchi ng淬火tem pering回火annealing退火carbonization碳化tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机。
工厂常用英语词汇一览表
工厂常用英语词汇一览表以下是一份包含工厂常用英语词汇的一览表：1. Raw materials（原材料）2. Production line（生产线）3. Assembly line（装配线）4. Manufacturing（制造）5. Quality control（质量控制）6. Inventory management（库存管理）7. Procurement（采购）8. Supply chain（供应链）9. Logistics（物流）10. Warehousing（仓储）11. Packaging（包装）12. Shipping（运输）13. Distribution（分销）14. Lean manufacturing（精益生产）15. Just-in-time (JIT)（准时生产）16. Six Sigma（六西格玛）17. Production planning（生产计划）18. Equipment maintenance（设备维护）19. Safety procedures（安全程序）20. Workstation（工作台）21. Operator（操作员）22. Supervisor（主管）23. Shift（班次）24. Overtime（加班）25. Cost analysis（成本分析）26. Efficiency（效率）27. Productivity（生产力）28. Waste reduction（减少浪费）29. Batch production（批量生产）30. Continuous production（连续生产）31. Quality assurance（质量保证）32. Defect（缺陷）33. Reject rate（废品率）34. Production target（生产目标）35. Lead time（交货时间）36. Breakdown（故障）37. Preventive maintenance（预防性维护）38. Standard operating procedures（标准操作程序）39. Work in progress（在制品）40. Finished goods（成品）41. Scrap（废料）42. Hazardous materials（危险物质）43. Environmental regulations（环境法规）44. Health and safety regulations（健康和安全规定）45. Engineering drawings（工程图纸）46. Machine operators（机器操作员）47. Parts inventory（零件库存）48. Replenishment（补货）49. Quality testing（质量测试）50. Training programs（培训计划）51. Low-cost labor（低成本劳动力）52. Efficiency improvement（效率提升）53. Cost reduction（成本降低）54. Just-in-case inventory（备用库存）55. Demand forecasting（需求预测）56. Supplier relationship management（供应商关系管理）57. Product specifications（产品规格）58. Assembly instructions（装配说明）59. Product inspection（产品检查）60. Order fulfillment（订单执行）61. Production capacity（生产能力）62. Rejection rate（拒绝率）63. Recycling（回收利用）64. Waste management（废物管理）65. Cost of goods sold（销售成本）66. Batch size（批量大小）67. Cycle time（循环时间）68. Equipment downtime（设备停机时间）69. Root cause analysis（根本原因分析）70. Continuous improvement（持续改进）71. Material handling（物料搬运）72. Kanban system（看板系统）73. Work instructions（工作说明）74. Quality management system（质量管理体系）75. Export regulations（出口法规）76. Production schedule（生产计划表）77. Safety equipment（安全设备）78. Production efficiency（生产效率）79. Performance metrics（绩效指标）80. Hazard identification（危险识别）81. Production costs（生产成本）82. Workforce allocation（员工分配）83. Waste disposal（废物处理）84. Quality standards（质量标准）85. Defect analysis（缺陷分析）86. Production volume（生产量）87. Energy consumption（能源消耗）88. Material waste（材料浪费）89. Continuous training（持续培训）90. Safety inspections（安全检查）91. Automation（自动化）92. Maintenance schedule（维修计划）93. Non-conforming products（不合格产品）94. Quality audits（质量审核）95. Workforce productivity（员工生产率）96. Material shortage（材料短缺）97. Defective parts（有缺陷的零件）98. Production delays（生产延迟）99. Quality improvement（质量改进）100. Cost control（成本控制）101. Supply chain management（供应链管理）102. Quality control inspector（质量控制检查员）103. Production supervisor（生产主管）104. Safety training（安全培训）105. Production target（生产目标）106. Cost reduction initiatives（成本降低计划）107. Waste elimination（浪费消除）108. Process improvement（流程改进）109. Material handling equipment（物料搬运设备）110. Production efficiency analysis（生产效率分析）111. Machine maintenance schedule（机器维护计划）112. Non-compliance（不符合）113. Quality assurance program（质量保证计划）114. Inventory management system（库存管理系统）115. Production line efficiency（生产线效率）116. Safety guidelines（安全指南）117. Production capacity planning（生产能力规划）118. Material specifications（物料规格）119. Quality control procedures（质量控制程序）120. Lean management principles（精益管理原则）121. Waste reduction strategies（减少浪费策略）122. Defect prevention（缺陷预防）123. Production reporting（生产报告）124. Cost analysis report（成本分析报告）125. Workstation layout（工作台布局）126. Safety protocols（安全协议）127. Supply chain optimization（供应链优化）128. Production forecasting（生产预测）129. Quality improvement initiatives（质量改进计划）130. Production schedule adherence（生产计划符合情况）131. Waste management system（废物管理系统）132. Emergency response plan（应急响应计划）133. Production downtime（生产停机时间）134. Quality control standards（质量控制标准）135. Equipment calibration（设备校准）136. Material handling procedures（物料搬运程序）137. Quality control checklist（质量控制清单）138. Production data analysis（生产数据分析）139. Lean production techniques（精益生产技术）140. Production cost tracking（生产成本追踪）141. Waste reduction goals（减少浪费目标）142. Defect tracking（缺陷追踪）143. Production efficiency metrics（生产效率指标）144. Safety procedures manual（安全程序手册）145. Supplier evaluation（供应商评估）146. Production process optimization（生产流程优化）147. Material handling efficiency（物料搬运效率）148. Quality control documentation（质量控制文件）149. Production target achievement（生产目标达成情况）150. Cost estimation（成本估算）151. Workforce training（员工培训）152. Waste disposal system（废物处理系统）153. Emergency drills（紧急演习）154. Production capacity utilization（生产能力利用率）155. Quality control measures（质量控制措施）156. Equipment maintenance records（设备维护记录）157. Material handling policies（物料搬运政策）158. Quality control system implementation（质量控制系统实施）159. Lean production implementation（精益生产实施）160. Production cost analysis（生产成本分析）在工厂工作中，我们经常会遇到各种需要使用专业术语的场景。
工厂常用词汇-精华总结
工厂常用词汇 适合多专业使用Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OPI open box inspection开箱检查fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板 zhan banbarcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch镑、英寸EMI gasket导电条front plate前板rear plate后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件plastic parts塑胶件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线forklift叉车production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |'plein?|刨床miller铣床grinder磨床driller铣床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长 department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运 #p#分页标题#e#be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skr?pid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dei?n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓name of a department部门名称administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车forklift叉车pallet栈板glove(s)手套glove(s) with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头sweeper扫把mop拖把vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机production line流水线chain链条槽magnetizer加磁器lamp holder灯架to mop the floor拖地 #p#分页标题#e#to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位safety安全quality品质delivery deadline交货期cost成本engineering工程die repair模修enterprise plan = enterprise expansion projects企划QC品管die worker模工production, to produce生产equipment设备to start a press开机stop/switch off a press关机classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products, up-to-grade products良品defective products, not up-to-grade products不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱die change 换模to fix a die装模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cut material, to input落料 #p#分页标题#e#to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, not qualified不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for 准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位lots of production生产批量steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify修订to switch over to, switch---to throw--over switching over切换engineering, project difficulty 工程瓶颈stage die工程模automation自动化to stake, staking, reviting铆合add lubricating oil加润滑油shut die架模shut height of a die架模高度analog-mode device类模器die lifter举模器argon welding氩焊vocabulary for stamping冲压常词汇stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to.to send delinery backto retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报 #p#分页标题#e# safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑common vocabulary for die engineering 模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die 连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder文件夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerazation装箱quantity of physical invetory second count 复盘点数量quantity of customs count 会计师盘,点数量 #p#分页标题#e#the first page第一联filed by accounting department for reference会计部存查end-user/using unit(department)使用单位summary of year-end physical inventory bills 年终盘点截止单据汇总表bill name单据名称This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financialdepartment) 本表请与盘点清册一起送会计部－(NHK厂区送财会部) Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO. 空白与作废单号plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材material statistics sheet 物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量 #p#分页标题#e#cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品 #p#分页标题#e# disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点 #p#分页标题#e#dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location 定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆 #p#分页标题#e# trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控 母模core模心 公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口 #p#分页标题#e# fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣品质人员名称类QC quality control 品质管理人员FQC final quality control 终点品质管制人员IPQC in process quality control 制程中的品质管制人员OQC output quality control 最终出货品质管制人员IQC incoming quality control 进料品质管制人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 品质工程人员品质保证类FAI first article inspection 新品首件检查FAA first article assurance 首件确认TVR tool verification report 模具确认报告3B 3B 模具正式投产前确认CP capability index 能力指数CPK capability index of process 模具制程能力参数SSQA standardized supplier quality 合格供应商品质评估OOBA out of box audit 开箱检查QFD quality function deployment 品质机能展开FMEA failure model effectiveness analysis 失效模式分析8 disciplines 8项回复内容FA final audit 最後一次稽核CAR corrective action request 改正行动要求corrective action report 改正行动报告FQC运作类AQL Acceptable Quality Level 运作类允收品质水准S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ Average Output Quality 平均出厂品质AOQL Average Output Quality Level 平均出厂品质Q/R/S Quality/Reliability/Service 品质/可靠度服务MIL-STD Military-Standard 军用标准S I-S IV Special I-Special IV 特殊抽样水准等级P/N Part Number 料号L/N Lot Number 特采AOD Accept On Deviation 特采 #p#分页标题#e#UAI Use As It 首件检查报告FPIR First Piece Inspection Report 百万分之一PPM Percent Per Million 批号制程统计品管专类SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计品质管制R Range 全距AR Averary Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR Gauge Reproducibility&Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它品质术语类QCC Quality Control Circle 品质圈QIT Quality Improvement Team 品质改善小组PDCA Plan Do Check Action 计划 执行 检查 总结ZD Zero Defect 零缺点QI Quality Improvement 品质改善QP Quality Policy 目标方针TQM Total Quality Management 全面品质管理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低品质水准RMA Return Material Audit 退料认可QAN Quality Amelionrate Notice 品质改善活动ADM Absolute Dimension Measuremat 全尺寸测量QT Quality Target 品质目标7QCTools 7 Quality Controll Tools 品管七大手法通用之件类ECN Engineering Change Notes 工程变更通知(供应商) ECO Engineering Change Order 工程改动要求(客户) PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Specification In Process 制程检验规格SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill OfMaterial 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QC Quality System 品质系统ES Engineering Standarization 工程标准CGOO China General PCE龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司 #p#分页标题#e#T TAIWAN 台湾IWS International Workman Standard 工艺标准ISO International Standard Organization 国际标准化组织GS General Specification 一般规格PMC Production & Material Control 生产和物料控制PPC Production Plan Control 生产计划控制MC Material Control 物料控制ME Manafacture Engineering 制造工程部PE Project Engineering 产品工程部A/C Accountant Dept 会计部P/A Personal & Administration 人事行政部DC Document Center 资料中心QE Quality Engineering 品质工程(部)QA Quality Assurance 品质保证(处)QC Quality Control 品质管制(课)PD Product Department 生产部LAB Labratry 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供应商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号其它OEM Original Equipment Manufacture 原设备制造PCE Personal Computer Enclosure 个人电脑外设PC Personal Computer 个人电脑CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大陆PRC People's Republic of China 中国大陆U.S.A the United States of America 美国A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存I/O Input/Output 输入/输出OK Ok 好NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electry-static Discharge 静电排放5S 希腊语 整理,整顿,清扫,清洁,教养ATIN Attention 知会CC Carbon Copy 副本复印相关人员 #p#分页标题#e#APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光碟CD-ROM Compact Disk Read-Only Memory 只读光碟FDD Floppy Disk Drive 软碟机HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CAV Cavity 模穴CAD Computer Aid Design 计算机辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly Delivery Requitement 周出货需求C?T Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间)S/T Standard Time 标准时间P/M Product Market 产品市场3C Computer,Commumcation,Consumer electronic's 消费性电子5WIH When,Where,Who,What,Why,How to5M Man,Machine,Material,Method,Measurement4MIH Man,Materia,Money,Method,Time 人力,物力,财务,技术,时间(资源)SQA Strategy Quality Assurance 策略品质保证DQA Desigh Quality Assurance 设计品质保证MQA Manufacture Quality Assurance 制造品质保证SSQA Sales and service Quality Assurance 销售及服务品质保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic Magnetion Inspect 高磁测试FMI Frequency Modulatim Inspect 高频测试B/M Boar/Molding(flat cable)C/P Connector of PCA/P AssemblySPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Vedio DiskVCD Vdeio Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID ManufacturingCAE Computer AID EngineeringABIOS Achanced Basic in put/output system 先进的基本输入/输出系统CMOS Complemeruary Metoll Oxide Semiconductor 互补金属氧化物半导体PDA Personal Digital Assistant 个人数字助理IC Integrated Circuit 集成电路ISA Industry Standard Architecture 工业标准体制结构MCA Micro Channel Architecture 微通道结构EISA Extended Industry Standard Architecture 扩充的工业标准结构 #p#分页标题#e#SIMM Single in-line memory module 单项导通汇流组件DIMM Dual in-line Memory Module 双项导通汇流组件LED Light-Emitting Diode 发光二级管FMEA Failure Mode Effectivenes 失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Calle 排线PCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WPR Weekly Delivery Requirement 周出货要求PPM Parts Per Million 百万分之一TPM Total Production Maintenance 全面生产保养MRP Material Requiremcnt Planning 物料需计划OC Operation System 作业系统TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProceduneEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material Size模具技术用语 各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming ?泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造 #p#分页标题#e# matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模ouvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 叠层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模 #p#分页标题#e#swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀 anchor pin 锚梢angular pin 角梢 baffle 调节阻板angular pin 倾斜梢 baffle plate 折流档板ball button 球塞套 ball plunger 定位球塞ball slider 球塞滑块 binder plate 压板blank holder 防皱压板 blanking die 落料冲头bolster 上下模板 bottom board 浇注底板bolster 垫板 bottom plate 下固定板bracket 托架 bumper block 缓冲块buster 堵口 casting ladle 浇注包casting lug 铸耳 cavity 模穴(模仁)cavity retainer plate 模穴托板 center pin 中心梢clamping block 锁定块 coil spring 螺旋弹簧cold punched nut 冷冲螺母 cooling spiral 螺旋冷却栓core 心型 core pin 心型梢cotter 开口梢 cross 十字接头cushion pin 缓冲梢 diaphragm gate 盘形浇口die approach 模头料道 die bed 型底die block 块形模体 die body 铸模座die bush 合模衬套 die button 冲模母模die clamper 夹模器 die fastener 模具固定用零件die holder 母模固定板 die lip 模唇die plate 冲模板 die set 冲压模座direct gate 直接浇口 dog chuck 爪牙夹头dowel 定位梢 dowel hole 导套孔dowel pin 合模梢 dozzle 辅助浇口dowel pin 定位梢 draft 拔模锥度draw bead 张力调整杆 drive bearing 传动轴承ejection pad 顶出衬垫 ejector 脱模器ejector guide pin 顶出导梢 ejector leader busher 顶出导梢衬套ejector pad 顶出垫 ejector pin 顶出梢ejector plate 顶出板 ejector rod 顶出杆ejector sleeve 顶出衬套 ejector valve 顶出阀eye bolt 环首螺栓 filling core 椿入蕊film gate 薄膜形浇口 finger pin 指形梢finish machined plate 角形模板 finish machined round plate 圆形模板fixed bolster plate 固定侧模板 flanged pin 带凸缘?flash gate 毛边形浇口 flask 上箱floating punch 浮动冲头 gate 浇口gate land 浇口面 gib 凹形拉紧?goose neck 鹅颈管 guide bushing 引导衬套 #p#分页标题#e# guide pin 导梢 guide post 引导柱guide plate 导板 guide rail 导轨head punch 顶?冲头 headless punch 直柄冲头heavily tapered solid 整体模蕊盒 hose nippler 管接头impact damper 缓冲器 injection ram 压射柱塞inlay busher 嵌入衬套 inner plunger 内柱塞inner punch 内冲头 insert 嵌件insert pin 嵌件梢 king pin 转向梢king pin bush 主梢衬套 knockout bar 脱模杵land 合模平坦面 land area 合模面leader busher 导梢衬套 lifting pin 起模顶?lining 内衬 locating center punch 定位中心冲头locating pilot pin 定位导梢 locating ring 定位环lock block 压块 locking block 定位块locking plate 定位板 loose bush 活动衬套making die 打印冲子 manifold block 歧管档块master plate 靠模样板 match plate 分型板mold base 塑胶模座 mold clamp 铸模紧固夹mold platen 模用板 moving bolster 换模保持装置moving bolster plate 可动侧模板 one piece casting 整体铸件parallel block 平行垫块 paring line 分模线parting lock set 合模定位器 pass guide 穴型导板peened head punch 镶入式冲头 pilot pin 导?pin gate 针尖浇口 plate 衬板pre extrusion punch 顶挤冲头 punch 冲头puncher 推杆 pusher pin 衬套梢rack 机架 rapping rod 起模杆re-entrant mold 凹入模 retainer pin 嵌件梢retainer plate 托料板 return pin 回位梢riding stripper 浮动脱模器 ring gate 环型浇口roller 滚筒 runner 流道runner ejector set 流道顶出器 runner lock pin 流道拉梢。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
工廠常用英語詞彙一覽表按類別查詢簡表Rev: 011.生產規格(Specification or Spec).1.1 BOM: Bill of material 料表1.2 S/N: Spec notice 生產注意事項1.3: ES : Electrical Spec 電氣規格1.4: PK: Schematic 電路圖1.5: PD: Physical dimension 外觀尺寸圖ES: Input characterization 輸入特性1.1 Input voltage range 輸入電壓範圍1.2 Input frequency range 輸入頻率範圍1.3 Max .input AC current 最大輸入交流電流1.4 Inrush current(cold start) 突增電流（冷開機）1.5 Efficency:60% Min.At nomall line 效率:60%，一般電壓（指115/230V,除非另有說明）Noise test 雜訊測試Static output characteristics 靜態輸出特性Dynamic output characteristics 動態輸出特性Rise time DC輸出電壓上升時間Hold up time DC輸出電壓持續時間Protection: 保護OVP(over voltage protection) 過電壓保護OPP(over power protection) 過功率保護OCP(over current protection) 過電流保護OTP(over temp protection) 過溫度保護Short circuit protection 短路保護Hi-pot(dielectric withstand voltage) 耐電壓測試1.1 Primary to secondary 初級對次級 AC TO DC1.2 Primary to safety ground 初級對地 AC TO FG1.3 Secondary to protection) 次級對地 DC TO FG1.4 Insulation resistance 絕緣阻抗1.5 Leakage current 漏電流Electrical常用單詞regulation 調整voltage / current電壓／電流ripple / noise / buzz 漣波／雜訊／異音frequency / load 頻率／負載no power (NOP）無輸出full load / low load重載／輕載broken / blow out (BRO 燒機damage / adjust 損壞／調整open / short 開路／短路oscilloscope示波器SPEC(規格）常用單詞model: 機種 revision: 版本issued date: 發行日期P/N: 品名，料號discrption: 說明remark:備注reported by: 草擬cheched by: 審核approved by: 核準2.FN(factory noice):工廠變更通知 / ECN(cngineering change notice)工程變更通知2.1 FN實施方式： Immediate change 立即變更 Running change 舊料用完用新料2.2 ECN: old rev.(舊版本）new rev.(新版本） drawing no / customer/ alteration ref(圖號 / 客戶 / 變更依據)3.Department 部門3.1 MFG: manufacturing 制造3.1.1 AI: auto insertion 自動插件3.1.2 preforming 加工3.1.3 SMD 自動粘著3.2 QA: quality assurance 品保3.2.1 VQA 進料品質保證3.2.2 PQC ,FQC 製程品管3.2.3 Calibration , safety 儀校，安規3.3 PE: production engineering 制造工程3.3.1 TE: test engineering 測試工程3.3.2 ME: mechanical engineering 機械工程3.3.3 IE: industrial engineering 工業工程3.4 HR: human resources 人力資源3.5 Material 物料3.5.1 PC:production control 生管3.5.2 purchasing 采購3.5.3 warehouse 倉庫3.6 ENG: engineering 工程3.6.1 document center 資料中心4. Safety4.1 UL(Underwriters Laboratories) 美國保險協會實驗室4.2 CSA(Canadian Standards Association) 加拿大標準協會4.3 TUV 德國技術監護協會4.4 VDE 德國電氣標準4.5 NEMKO 挪威電氣標準4.6 DEMKO 丹麥電氣標準4.7 CCEE(China Commission for Conformity 中國電工產品認證委員會Certification of Electronical Equipment)4.8 CCIB(China Commodity Inspection Bureau) 中國商品檢驗局5. Other 其他FAX(傳真): date,to,fm,subject, dear, TKS, best regards,FAR: issue,description,corrective action,preventive action, analysis,defect,failure,supplier/vendorISO: International Organization for Standardization 國際標準化組織Quality Manual:品質手冊Procedure:作業程序Quality policy: Quality Reliability Excellence品質至上信賴第一追求卓越6.Contraction(縮寫)AQL: accept quality level 允收水準ATS: auto test system 自動測試系統CR: critical 嚴重ESD: electrostatic discharge 靜電放電FET: field effective transistor 場效電晶體ICT: in-circuit test 線路測試MA: major 主要MI: minor 次要MRB: material review board 不良材料審核組NTC: negative temperature characteristic 熱敏電阻O/I: operation instruction 工作指導書PWM: pulse width modification 脈波寬調整S/N: series number 序號SMD: surface mounting device 表面沾著WIP: work in progress 半成品(工作進行中)JIT: just in timeIR: infra-red 紅外線的PDPC: Process, Decision, Program, ChartQCCA: quality control circle activities 品管圈活動CWQC: company-wide quality control 全面品管QCCA: quality control circle activities 品管圈活動CWQC: company-wide quality control 全面品管ponent(零件)bobbin 線軸shield 背板bridge diode 橋式整流triode 三極管cable tie 束帶tape 膠布capactitor(cap) 電容screw tapping 自攻螺絲case 外殼screw machine 機械螺絲ceramic capacitor 陶瓷電容terminal 端子chip capacitor 晶片電容transformer(X'FMR) 變壓器chip resistor 晶片電阻transistor 電晶體choke 線圈tube 套管connector 連接器varistor 突波吸收器control board 基板VR(variable resistance) 可變電阻diode 二極體washer 墊片epoxy 樹脂zener 齊納fan 風扇photo couple 光藕合二極體FET 場效電晶體regulator 穩壓器filter 濾波器resistor 電阻fuse 保險絲ricer 鉚釘fuse clip 保險絲底座screw 螺絲fuse holder 保險絲底座socket 插座glue 膠 solder bar 錫棒heatsink 散熱片sping washer 彈簧墊片IC 集成電路stand-off 支柱inductor 電感star washer 星形墊片insulator 絕緣片switch 開關jumper wire 跳線output cable 輸出線label 標簽output wire 輸出線lock washer 接地唾形墊片PCB 電路板NTC 熱敏電阻LED 發光二極體nut 螺絲帽tubber foot 腳墊TEFLON 鐵弗龍套管8.Time(時間)Jan.(Janury) 一月month 月份Feb.(February) 二月period 期間Mar.(March) 三月quarter 季Apr.(April) 四月since 從…..May 五月week 周Jun.(June) 六月after 在……之後Jul.(July) 七月before 在……之前Aug.(August) 八月 date 日期Sept.(September) 九月Oct.(October) 十月Nov.(November) 十一月Dec.(December) 十二月Mon=Monday 星期一Tue=Tuesday 星期二Wed=Wednesday 星期三Thu=Thursday 星期四Fri=Friday 星期五Sat=Saturday 星期六Sun=Sunday 星期日9.Ver(動詞)change 改變pay 付給check 檢查produce 產生come 來 provide 提供damage 損傷receive 收到find 發現replace 代替fix 修理 send 發出go 去 take 拿,采取happen 發生touch 踫觸improve 改善wind 纏(盤,卷)繞,扭曲insert 插入issue 發行make 做,使10.Non(名詞)action 動作,措施analysis 分析condition 條件data 資料defect 缺點disposition 處置engineer 工程師failure 失敗file 文件夾inspector 檢驗員11.Process(製程)assembly 組立method 方法burn-in(B/I) 崩應model 機種component 零件noise 噪音flux 助焊劑pallet 棧板function test 功能測試paper 紙張gravity 比重 plan 設劃Hi-pot test 耐高壓測試position 位置insertion 插件problem 問題ORT 可靠度測試 procedure 程序packing 包裝product 產品solder machine 錫爐production 生產station 站別record 記錄supplier/vendor 廠商remark 備注temperature 溫度report 報告humidity 濕度requirement 要求torque 扭距sample 樣品touch-up(T/U) 補焊(二次作業) target 目標layout 設計圖trace (基板)線路location 位置waybill 運貨單manager 經理operator 作業員technician 技術員12.Color(顏色)black 黑色blue 藍色brown 棕色gold 金色gray 灰色green 綠色orange 橙色red 紅色silver 銀色violet(purple) 紫色white 白色yellow 黃色13.Number(數字)one 一 twenty 二十two 二twenty-one 二十一three 三thirty 三十four 四forty 四十five 五 fifty 五十six 六sixty 六十seven 七seventy 七十eight 八 seventy-three 七十三nine 九 eighty 八十ten 十ninety 九十eleven 十一 hundred 百twelve 十二 thousand 千thirteen 十三million 萬fourteen 十四fifteen 十五sixteen 十六seventeen 十七eighteen 十八nineteen 十九14.基本單位換算長度:1m=10dm=10*10cm=10*10*10mm1inch=25.4mm面積:1立方米=10*10平方分米=104平方釐米=106=1.5-e3体積:1立方米=10+e3=10+e6=10+e9=10+e3=10+e6=264.2重量:1公斤=1千克=103克(g)1磅=453.59克(g)電氣:電感(L) 1亨(H)=103毫亨=106微亨電阻(R) 1千歐=103歐=106毫歐電容(C) 1法=106微法=1012皮法電壓(V) 1千伏=103伏=106毫伏電流(A) 1安=103毫安=106微安頻率(f) 1(MHz)=103千赫(KHz)=106赫茲(Hz)。